OSDN Git Service
Vishnu Patekar [Sun, 25 Jan 2015 13:40:09 +0000 (19:10 +0530)]
ARM: sunxi: dts: Add A10/A20 PS2 pin muxing options
Signed-off-by: VishnuPatekar <vishnupatekar0510@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Vishnu Patekar [Sun, 25 Jan 2015 13:40:08 +0000 (19:10 +0530)]
ARM: sunxi: dts: Add PS2 nodes to dtsi for A10,A20
Signed-off-by: VishnuPatekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Sat, 24 Jan 2015 14:33:48 +0000 (22:33 +0800)]
ARM: dts: sun6i: Add resistive touchscreen controller node to dtsi
Now that we support the sun6i variant of the touchscreen controller,
add the device node to the dtsi so we can use it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Fri, 23 Jan 2015 15:39:23 +0000 (16:39 +0100)]
ARM: dts: sun4i: Add Hyundau A7HD board
The Hyundai A7HD is a 7" 16:9 A10 powered tablet featuring 1G RAM, 8G
nand, 1024x600 IPS screen, a mini hdmi port, mini usb receptacle and a
headphones port for details see: http://linux-sunxi.org/Hyundai_A7HD
Cc: Mark Janssen <maniac@maniac.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Aleksei Mamlin [Tue, 20 Jan 2015 18:03:28 +0000 (22:03 +0400)]
ARM: dts: sun4i: Add Marsboard A10 board
This patch add support for Marsboard A10 board.
The Marsboard A10 is a A10 based development board with 1G RAM, 1G NAND,
micro SD card slot, SATA 2.0 socket, 10/100 ethernet, mini HDMI port,
1 USB OTG port and 2 USB 2.0 ports. Board does not use the AXP209 pmic,
it does not have a pmic at all.
Board also have 2 expansion 70 pin headers.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Sat, 17 Jan 2015 05:19:34 +0000 (13:19 +0800)]
ARM: dts: sun9i: Enable mmc2 on A80 Optimus Board
The A80 Optimus Board has a 16GB eMMC connected to mmc2, with 8 bit
wide data bus.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Sat, 17 Jan 2015 05:19:33 +0000 (13:19 +0800)]
ARM: dts: sun9i: Add 8 bit mmc pinmux setting for mmc2
mmc2 is available on port C. Add a pinmux setting for 8 bit wide eMMC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Sat, 17 Jan 2015 05:19:32 +0000 (13:19 +0800)]
ARM: dts: sun9i: Enable mmc0 on A80 Optimus Board
Enable the micro-sd slot on the A80 Optimus Board, which is connected to
mmc0. This adds the card-detect gpio and enables mmc0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Sat, 17 Jan 2015 05:19:31 +0000 (13:19 +0800)]
ARM: dts: sun9i: Convert a80 optimus board dts to label referencing
The preferred method of referencing nodes from the dtsi is to use
labels, instead of copying the complete tree.
This patch converts sun9i-a80-optimus.dts to use label references.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Sat, 17 Jan 2015 05:19:30 +0000 (13:19 +0800)]
ARM: dts: sun9i: Add mmc controller nodes to the A80 dtsi
The A80 has 4 mmc controllers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Sat, 17 Jan 2015 05:19:29 +0000 (13:19 +0800)]
ARM: dts: sun9i: Add mmc config clock nodes
Add the device tree nodes for the mmc config clock nodes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Aleksei Mamlin [Mon, 19 Jan 2015 19:35:22 +0000 (22:35 +0300)]
ARM: dts: sunxi: Add missing mdio label
This patch add missing mdio label for sun[457]i.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 18 Jan 2015 12:09:45 +0000 (13:09 +0100)]
ARM: dts: sun5i: Add mk802_a10s board
The mk802_a10s re-uses is the "classic" mk802 case and functionality, but has
an A10s SoC inside rather then the A10, it features 512M or 1G RAM, 4G nand,
a mini-hdmi female connector, USB-A receptacle, mini-usb receptacle (OTG)
and a sdio realtek wifi chip. Unlike the original mk802 it does have a pmic,
the axp152.
For more details see: http://linux-sunxi.org/Semitime_g2
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Changed the compatible and node names labels]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 18 Jan 2015 12:09:44 +0000 (13:09 +0100)]
ARM: dts: sun4i: Add mk802ii board
The mk802ii is a revised version of the mk802 A10 based hdmi tv-stick, it
features 1G RAM, 4G nand, a hdmi male connector, USB-A receptacle, 2 micro
usb receptacles (OTG & power) and USB-wifi, and does come with an axp209 pmic.
For more details see: http://linux-sunxi.org/Rikomagic_mk802ii
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 18 Jan 2015 12:09:43 +0000 (13:09 +0100)]
ARM: dts: sun4i: Add mk802 board
The mk802 is the "classic" Allwinner A10 based hdmi tv-stick, it features
512M or 1G RAM, 4G nand, a mini-hdmi female connector, USB-A receptacle,
mini-usb receptacle (OTG) and USB-wifi. Somewhat unique the mk802 does not
use the AXP209 pmic, it does not have a pmic at all.
For more details see: http://linux-sunxi.org/Rikomagic_mk802
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 18 Jan 2015 12:08:20 +0000 (13:08 +0100)]
ARM: dts: sun4i: Add dts file for Chuwi V7 CW0825 tablet
The Chuwi V7 is an A10 (sun4i) based tablet with 1G of RAM, 16G of nand flash,
microsd slot, 7" 1024x768 lvds ips panel, mini hdmi out, headphones out,
stereo speakers, front & back camera and usb wifi.
It is clearly marked "CHUWI", "V7" and "Model: CW0825" on the back of the
tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 18 Jan 2015 12:08:19 +0000 (13:08 +0100)]
ARM: dts: sun7i: Add dts file for Bananapro board
Add support for the new Bananapro A20 development board from lemaker.org.
This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for
OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver,
3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Sun, 11 Jan 2015 19:33:44 +0000 (20:33 +0100)]
ARM: sun6i: Enable ARM arch timers
The A31 has non-initialized architected timers, without CNTFRQ or CNTVOFF set
by the Allwinner's bootloader.
Use the new DT property for such case, and enable the arch timers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Thu, 15 Jan 2015 15:50:15 +0000 (23:50 +0800)]
ARM: dts: sun6i: Convert hummingbird a31 dts to label references
Using label references is preferred when override settings from the
included dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Tue, 13 Jan 2015 01:37:31 +0000 (09:37 +0800)]
ARM: dts: sun9i: Add pinmux setting for mmc0
mmc0 is only available on port F, and is always used with a 4 bit wide
bus for the onboard micro-sd slot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Tue, 13 Jan 2015 01:37:29 +0000 (09:37 +0800)]
ARM: dts: sunxi: Use label to reference pio in sunxi-common-regulators
Use the label to reference the pin controller node, so that we can use
sunxi-common-regulators with sunxi families that don't share the same
address space mappings, such as sun9i.
This patch is mostly space changes due to the reduction of node parents.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Tue, 13 Jan 2015 01:37:27 +0000 (09:37 +0800)]
ARM: dts: sun9i: Add clock-indices property for bus gate clocks
of_clk_get_parent_name() uses the clock-indices property to resolve
clock phandle arguments in case that the argument index does not
match the clock-output-names sequence.
This is the case on sunxi, where we use the actual bit index as the
argument to the phandle. Add the clock-indices property so that
of_clk_get_parent_name() resolves the names correctly.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Tue, 13 Jan 2015 01:37:25 +0000 (09:37 +0800)]
ARM: dts: sun9i: Add mmc module clock nodes for A80
The mmc module clocks are A80 specific module 0 (storage) type clocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 2 Sep 2014 17:25:26 +0000 (19:25 +0200)]
ARM: sun7i: cubietruck: Relicense the device tree under GPLv2/X11
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexander Bersenev <bay@hackerdom.ru>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Olliver Schinagl <oliver@schinagl.nl>
Maxime Ripard [Tue, 2 Sep 2014 17:25:26 +0000 (19:25 +0200)]
ARM: sun7i: cubieboard2: Relicense the device tree under GPLv2/X11
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexander Bersenev <bay@hackerdom.ru>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Roman Byshko <rbyshko@gmail.com>
Hans de Goede [Tue, 13 Jan 2015 10:44:32 +0000 (11:44 +0100)]
ARM: dts: sun8i: Add dts file for Ippo Q8H v1.2 tablets
The Ippo Q8H v1.2 is almost identical to the v5, still it needs a separate
dtb file since some gpio-s surrounding the wlan/bluetooth are different,
it uses different camera sensors, and different DRAM timings.
Note that atm neither the wlan/bluetooth nor the camera are supported, so
atm their is no difference between the dts files, but because of the different
DRAM timings there are already separate u-boot configs for the 2 different
versions, and the 1.2 config refers to sun8i-a23-ippo-q8h-v1.2.dtb to be
future proof, so we need to provide a sun8i-a23-ippo-q8h-v1.2.dtb file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Tue, 13 Jan 2015 10:47:04 +0000 (11:47 +0100)]
ARM: dts: sun8i: Enable lradc on a23-ippo-q8h-v5
The a23-ippo-q8h tablets have volume up/down buttons using the lradc. This
has been tested on both a v5 and a v1.2 tablet.
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Tue, 13 Jan 2015 10:47:03 +0000 (11:47 +0100)]
ARM: dts: sun8i: Add lradc node to sun8i-a23.dtsi
The A23 has the same lradc controller as previous Allwinner SoCs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Mon, 12 Jan 2015 04:34:09 +0000 (12:34 +0800)]
ARM: dts: sun4i: cubieboard: add axp209 regulator nodes
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.
The regulator names and constraints are based on the board
schematics and the SoC datasheet.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Mon, 12 Jan 2015 04:34:07 +0000 (12:34 +0800)]
ARM: dts: sun5i: hsg-h702: add axp209 regulator nodes
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.
The regulator names and constraints are based on the board
schematics and the SoC datasheet.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
LDO3 powers the USB WiFi module. This patch also references it
from the usb-phy node.
Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Mon, 12 Jan 2015 04:34:05 +0000 (12:34 +0800)]
ARM: dts: sun7i: cubietruck: add axp209 regulator nodes
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.
The regulator names and constraints are based on the board
schematics and the SoC datasheet.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Mon, 12 Jan 2015 04:34:04 +0000 (12:34 +0800)]
ARM: dts: sun7i: cubieboard2: add axp209 regulator nodes
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.
The regulator names and constraints are based on the board
schematics and the SoC datasheet.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Mon, 12 Jan 2015 04:34:08 +0000 (12:34 +0800)]
ARM: dts: sun4i: Add cpu thermal zones to dtsi
The core temperature sensor now supports thermal zones. Add a thermal
zone mapping for the cpus with passive cooling (cpufreq throttling).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Mon, 12 Jan 2015 04:34:06 +0000 (12:34 +0800)]
ARM: dts: sun5i: Add cpu thermal zones to dtsi
The core temperature sensor now supports thermal zones. Add a thermal
zone mapping for the cpus with passive cooling (cpufreq throttling).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Mon, 12 Jan 2015 04:34:03 +0000 (12:34 +0800)]
ARM: dts: sun7i: Add cpu thermal zones to dtsi
The core temperature sensor now supports thermal zones. Add a thermal
zone mapping for the cpus with passive cooling (cpufreq throttling).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Mon, 12 Jan 2015 04:34:02 +0000 (12:34 +0800)]
ARM: dts: sunxi: Add dtsi for AXP209 PMIC
The AXP209 PMIC is used with some Allwinner SoCs. This patch adds
a dtsi file listing all the regulator nodes. The regulators are
initialized based on their device node names.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Zoltan HERPAI [Thu, 8 Jan 2015 09:34:24 +0000 (10:34 +0100)]
ARM: dts: pcduino: Enable user LED and button support for pcDuino
The pcDuino board has LEDs connected to PH15/PH16, and back/home/menu
buttons to PH17/18/19 respectively. Enable these via gpio-leds and
gpio-keys. This is shared across the v1 and v2 versions of the board.
Tested on a v2 and verified against the schematics of a v1.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Added some newlines between the button nodes]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Mon, 19 Jan 2015 13:05:12 +0000 (14:05 +0100)]
ARM: dts: sunxi: Add simplefb nodes for de_be0-lcd0, de_be0-lcd0-tve0 pipelines
Add simplefb nodes for "[de_fe0-]de_be0-lcd0" and "[de_fe0-]de_be0-lcd0-tve0"
display pipelines for when u-boot has set up a pipeline to drive a LCD panel /
VGA output rather then the HDMI output.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Tue, 6 Jan 2015 02:35:23 +0000 (10:35 +0800)]
ARM: dts: sun4i: Add cpu clock reference and operating points to dtsi
The cpu core is clocked from the "cpu" clock. Add a reference to it
in the first cpu node. Also add "cpu0" label to the node.
The operating points were taken from the A10 FEX files in the
sunxi-boards repository. All FEX files have the same settings.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Tue, 6 Jan 2015 02:35:20 +0000 (10:35 +0800)]
ARM: dts: sun5i: Add cpu clock reference and operating points to dtsi
The cpu core is clocked from the "cpu" clock. Add a reference to it
in the first cpu node. Also add "cpu0" label to the node.
The operating points were taken from the A13 FEX files in the
sunxi-boards repository. All FEX files have the same settings.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Tue, 6 Jan 2015 02:35:16 +0000 (10:35 +0800)]
ARM: dts: sun7i: Add cpu clock reference and operating points to dtsi
The cpu core is clocked from the "cpu" clock. Add a reference to it
in the first cpu node. Also add "cpu0" label to the node.
The operating points were taken from the A20 FEX files in the
sunxi-boards repository. Not all boards have the same settings. The
settings in this patch are the most generic ones.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Tue, 6 Jan 2015 02:35:15 +0000 (10:35 +0800)]
ARM: dts: sunxi: Enable thermal sensor support for RTP on sun[457]i
Now that the resistive touchpanel driver supports thermal sensors,
add the "#thermal-sensor-cells" property as required by the thermal
framework.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 16 Dec 2014 21:59:59 +0000 (22:59 +0100)]
ARM: sunxi: DT: Convert the DTs to use the generic interrupt header
The NMI IRQ controller uses the standard flags definition for the IRQ level and
edges.
Use the common header to use defines instead of opaque numbers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 16 Dec 2014 21:59:58 +0000 (22:59 +0100)]
ARM: sunxi: DT: Convert the DTs to use the GIC headers
The GIC requires some extra opaque arguments to set the IRQ type and flags.
Convert the DTs to using the common defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 16 Dec 2014 21:59:57 +0000 (22:59 +0100)]
ARM: sunxi: DT: Convert the DTs to use a header for the pinctrl nodes
The pinctrl nodes require some extra opaque arguments for the pull up and drive
strength values.
Introduce a new header file and convert the device trees to replace these
opaque numbers by defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 16 Dec 2014 21:59:56 +0000 (22:59 +0100)]
ARM: sunxi: DT: Convert the DTs to use a header for the DMA arguments
The DMA engine for the A10/A20 and derivatives require an opaque extra
argument.
Add a dt-bindings header, and convert the device trees to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 16 Dec 2014 21:59:55 +0000 (22:59 +0100)]
ARM: sunxi: DT: convert DTs to use common GPIOs includes
Replace the various raw GPIO flags by their definition in the common
dt-bindings header.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 16 Dec 2014 21:59:54 +0000 (22:59 +0100)]
ARM: sunxi: DT: Convert to device tree includes
Prepare the device trees to use the C preprocessor.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Mon, 29 Dec 2014 11:09:26 +0000 (12:09 +0100)]
ARM: dts: sun6i: Add dts file for CSQ CS908 board
The CSQ CS908 is an A31s based top-set box, with 1G RAM, 8G NAND,
rtl8188etv usb wifi, 2 USB A receptacles (1 connected through the OTG
controller), ethernet, 3.5 mm jack with a/v out and hdmi out.
Note it has no sdcard slot and therefore can only be fel booted.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Mon, 29 Dec 2014 11:09:25 +0000 (12:09 +0100)]
ARM: dts: sun6i: Add sun6i-a31s.dtsi
Add a dtsi file for A31s based boards.
Since the A31s is the same die as the A31 in a different package, this dtsi
simply includes sun6i-a31.dtsi and then overrides the pinctrl compatible to
reflect the different package, everything else is identical.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Tue, 23 Dec 2014 10:13:22 +0000 (11:13 +0100)]
ARM: dts: sun7i: Add lradc node
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Tue, 23 Dec 2014 10:13:21 +0000 (11:13 +0100)]
ARM: dts: sun5i: Add lradc node
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Tue, 23 Dec 2014 10:13:20 +0000 (11:13 +0100)]
ARM: dts: sun4i: Add lradc node
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Wed, 17 Dec 2014 17:18:22 +0000 (18:18 +0100)]
ARM: dts: sun6i: Enable ir receiver on the Mele M9
The Mele M9 has an ir receiver, enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Mon, 29 Dec 2014 11:09:24 +0000 (12:09 +0100)]
ARM: dts: sun6i: Add ir node
Add a node for the ir receiver found on the A31.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Added a node label]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Wed, 17 Dec 2014 17:18:19 +0000 (18:18 +0100)]
ARM: dts: sun6i: Add ir_clk node
Add an ir_clk sub-node to the prcm node.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Alexandru Gagniuc [Mon, 8 Dec 2014 10:14:02 +0000 (04:14 -0600)]
ARM: sun4i: dt: cubieboard: Enable SPI0
Only SPI0 is enabled, as the schematic denotes it as the only SPI bus,
while other pins are reserved for different peripherals.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Alexandru Gagniuc [Mon, 8 Dec 2014 10:14:01 +0000 (04:14 -0600)]
ARM: sun4i: dt: Add pin muxing options for SPI
These are based on the available SPI configurations of Cubieboard,
Olimex LIME, and PcDuino. There is no pin group for SPI3, as all the
boards seem to use those pins for EMAC.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Wed, 3 Dec 2014 07:19:13 +0000 (15:19 +0800)]
ARM: dts: sun6i: hummingbird: Add ethernet phy reset gpio properties
On the Hummingbird A31 board, the RTL8211E ethernet phy has its reset
line connect to a gpio pin, instead of floating like on other boards.
Add the stmmac properties for describing the reset gpio.
The reset delays were taken from the RTL8211E datasheet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 23 Nov 2014 13:38:14 +0000 (14:38 +0100)]
ARM: dts: sun6i: Add pinmux settings for the ir pins
Add pinmux settings for the ir receive pin of the A31.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Mon, 19 Jan 2015 13:01:17 +0000 (14:01 +0100)]
ARM: dts: sun4i: Add simplefb node with de_fe0-de_be0-lcd0-hdmi pipeline
Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. This can be avoided by letting the display frontend engine
do the dma from memory, and then letting it feed the data directly into
the backend unmodified, as the frontend does have deep enough fifo-s.
Note since u-boot-v2015.01 has been released using the de_be0-lcd0-hdmi
pipeline on sun4i, we need to keep that one around too (unfortunately).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Thu, 25 Dec 2014 12:25:19 +0000 (13:25 +0100)]
ARM: dts: sun6i: ippo-q8h-v5: Fix serial0 alias
The Ippo q8h has its serial console connected to the r-uart. Adjust the
serial0 alias to match.
This fixes the kernel serial console no longer working since 3.19-rc1, because
8250_dw.c now honors dt aliases, causing the serial console to be ttyS5 rather
then being ttyS0, as it was in 3.18 and before.
Note that adjusting bootargs instead is not an acceptable fix, because
console=ttyS0,115200 is used by a lot of bootscripts, etc. and this should
continue to work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Thu, 18 Dec 2014 11:10:35 +0000 (19:10 +0800)]
ARM: dts: sunxi: Fix usb-phy support for sun4i/sun5i
usbphy0 support in the sunxi usb-phy driver has been merged, but the
dtsi's for sun4i/sun5i haven't been updated. This results in the phy
driver failing to load, breaking usb support.
Fixes:
6827a46f5994 ('phy: sun4i: add support for USB phy0')
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Linus Torvalds [Sun, 21 Dec 2014 01:08:50 +0000 (17:08 -0800)]
Linux 3.19-rc1
Linus Torvalds [Sun, 21 Dec 2014 00:48:59 +0000 (16:48 -0800)]
Merge tag 'for-linus' of git://git./linux/kernel/git/borntraeger/linux
Pull ACCESS_ONCE cleanup preparation from Christian Borntraeger:
"kernel: Provide READ_ONCE and ASSIGN_ONCE
As discussed on LKML http://marc.info/?i=
54611D86.
4040306%40de.ibm.com
ACCESS_ONCE might fail with specific compilers for non-scalar
accesses.
Here is a set of patches to tackle that problem.
The first patch introduce READ_ONCE and ASSIGN_ONCE. If the data
structure is larger than the machine word size memcpy is used and a
warning is emitted. The next patches fix up several in-tree users of
ACCESS_ONCE on non-scalar types.
This does not yet contain a patch that forces ACCESS_ONCE to work only
on scalar types. This is targetted for the next merge window as Linux
next already contains new offenders regarding ACCESS_ONCE vs.
non-scalar types"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux:
s390/kvm: REPLACE barrier fixup with READ_ONCE
arm/spinlock: Replace ACCESS_ONCE with READ_ONCE
arm64/spinlock: Replace ACCESS_ONCE READ_ONCE
mips/gup: Replace ACCESS_ONCE with READ_ONCE
x86/gup: Replace ACCESS_ONCE with READ_ONCE
x86/spinlock: Replace ACCESS_ONCE with READ_ONCE
mm: replace ACCESS_ONCE with READ_ONCE or barriers
kernel: Provide READ_ONCE and ASSIGN_ONCE
Linus Torvalds [Sun, 21 Dec 2014 00:42:36 +0000 (16:42 -0800)]
Merge tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux
Pull clk framework updates from Mike Turquette:
"This is much later than usual due to several last minute bugs that had
to be addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future
which will better parition clock providers from clock consumers"
* tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: samsung: Fix Exynos 5420 pinctrl setup and clock disable failure due to domain being gated
ARM: OMAP3: clock: fix boot breakage in legacy mode
ARM: OMAP2+: clock: fix DPLL code to use new determine rate APIs
clk: Really fix deadlock with mmap_sem
clk: mmp: fix sparse non static symbol warning
clk: Change clk_ops->determine_rate to return a clk_hw as the best parent
clk: change clk_debugfs_add_file to take a struct clk_hw
clk: Don't expose __clk_get_accuracy
clk: Don't try to use a struct clk* after it could have been freed
clk: Remove unused function __clk_get_prepare_count
clk: samsung: Fix double add of syscore ops after driver rebind
clk: samsung: exynos4: set parent of sclk_hdmiphy to hdmi
clk: samsung: exynos4415: Fix build with PM_SLEEP disabled
clk: samsung: remove unnecessary inclusion of header files from clk.h
clk: samsung: remove unnecessary CONFIG_OF from clk.c
clk: samsung: Spelling s/bwtween/between/
clk: rockchip: Add support for the mmc clock phases using the framework
clk: rockchip: add bindings for the mmc clocks
clk: rockchip: rk3288 export i2s0_clkout for use in DT
clk: rockchip: use clock ID for DMC (memory controller) on rk3288
...
Linus Torvalds [Sat, 20 Dec 2014 21:52:52 +0000 (13:52 -0800)]
Merge branch 'i2c/for-next' of git://git./linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
"Included are two bugfixes needing some bigger refactoring (sh_mobile:
deferred probe with DMA, mv64xxx: fix offload support) and one
deprecated driver removal I thought would go in via ppc but I
misunderstood. It has a proper ack from BenH"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sh_mobile: fix uninitialized var when debug is enabled
macintosh: therm_pm72: delete deprecated driver
i2c: sh_mobile: I2C_SH_MOBILE should depend on HAS_DMA
i2c: sh_mobile: rework deferred probing
i2c: sh_mobile: refactor DMA setup
i2c: mv64xxx: rework offload support to fix several problems
i2c: mv64xxx: use BIT() macro for register value definitions
Linus Torvalds [Sat, 20 Dec 2014 21:42:57 +0000 (13:42 -0800)]
Merge tag 'scsi-for-linus' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI update from James Bottomley:
"This is a much shorter set of patches that were on the go but didn't
make it in to the early pull request for the merge window. It's
really a set of bug fixes plus some final cleanup work on the new tag
queue API"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
storvsc: ring buffer failures may result in I/O freeze
ipr: set scsi_level correctly for disk arrays
ipr: add support for async scanning to speed up boot
scsi_debug: fix missing "break;" in SDEBUG_UA_CAPACITY_CHANGED case
scsi_debug: take sdebug_host_list_lock when changing capacity
scsi_debug: improve driver description in Kconfig
scsi_debug: fix compare and write errors
qla2xxx: fix race in handling rport deletion during recovery causes panic
scsi: blacklist RSOC for Microsoft iSCSI target devices
scsi: fix random memory corruption with scsi-mq + T10 PI
Revert "[SCSI] mpt3sas: Remove phys on topology change"
Revert "[SCSI] mpt2sas: Remove phys on topology change."
esas2r: Correct typos of "validate" in a comment
fc: FCP_PTA_SIMPLE is 0
ibmvfc: remove unused tag variable
scsi: remove MSG_*_TAG defines
scsi: remove scsi_set_tag_type
scsi: remove scsi_get_tag_type
scsi: never drop to untagged mode during queue ramp down
scsi: remove ->change_queue_type method
Linus Torvalds [Sat, 20 Dec 2014 21:37:44 +0000 (13:37 -0800)]
Merge tag 'pm-config-3.19-rc1' of git://git./linux/kernel/git/rafael/linux-pm
Pull CONFIG_PM_RUNTIME elimination from Rafael Wysocki:
"This removes the last few uses of CONFIG_PM_RUNTIME introduced
recently and makes that config option finally go away.
CONFIG_PM will be available directly from the menu now and also it
will be selected automatically if CONFIG_SUSPEND or CONFIG_HIBERNATION
is set"
* tag 'pm-config-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Eliminate CONFIG_PM_RUNTIME
tty: 8250_omap: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound: sst-haswell-pcm: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
Linus Torvalds [Sat, 20 Dec 2014 21:33:03 +0000 (13:33 -0800)]
Merge branch 'misc' of git://git./linux/kernel/git/mmarek/kbuild
Pull misc kbuild changes from Michal Marek:
"There are only a few things in the misc branch:
- Fix for bugon.cocci semantic patch
- Kdevelop4 files are .gitignored
- Put make binrpm-pkg on diet"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scripts/package: binrpm-pkg do not create source and devel package
.gitignore: Add Kdevelop4 project files
bugon.cocci: fix Options at the macro
Linus Torvalds [Sat, 20 Dec 2014 21:31:14 +0000 (13:31 -0800)]
Merge branch 'kbuild' of git://git./linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
"Here are the kbuild changes for v3.19-rc1:
- Cleanups and deduplication in the main Makefile and
scripts/Makefile.*
- Sort the output of *config targets in make help
- Old <linux/version.h> is always removed to avoid a surprise during
bisecting
- Warning fix in kconfig"
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: remove redundant -rR flag of hdr-inst
kbuild: Fix make help-<board series> on powerpc
kbuild: Automatically remove stale <linux/version.h> file
kconfig: Fix warning "‘jump’ may be used uninitialized"
Makefile: sort list of defconfig targets in make help output
kbuild: Remove duplicate $(cmd) definition in Makefile.clean
kbuild: collect shorthands into scripts/Kbuild.include
Wolfram Sang [Tue, 16 Dec 2014 12:31:26 +0000 (13:31 +0100)]
i2c: sh_mobile: fix uninitialized var when debug is enabled
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Linus Torvalds [Sat, 20 Dec 2014 02:19:19 +0000 (18:19 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull vfs pile #3 from Al Viro:
"Assorted fixes and patches from the last cycle"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
[regression] chunk lost from bd9b51
vfs: make mounts and mountstats honor root dir like mountinfo does
vfs: cleanup show_mountinfo
init: fix read-write root mount
unfuck binfmt_misc.c (broken by commit
e6084d4)
vm_area_operations: kill ->migrate()
new helper: iter_is_iovec()
move_extent_per_page(): get rid of unused w_flags
lustre: get rid of playing with ->fs
btrfs: filp_open() returns ERR_PTR() on failure, not NULL...
Linus Torvalds [Sat, 20 Dec 2014 02:15:12 +0000 (18:15 -0800)]
Merge tag 'ecryptfs-3.19-rc1-fixes' of git://git./linux/kernel/git/tyhicks/ecryptfs
Pull eCryptfs fixes from Tyler Hicks:
"Fixes for filename decryption and encrypted view plus a cleanup
- The filename decryption routines were, at times, writing a zero
byte one character past the end of the filename buffer
- The encrypted view feature attempted, and failed, to roll its own
form of enforcing a read-only mount instead of letting the VFS
enforce it"
* tag 'ecryptfs-3.19-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: Remove buggy and unnecessary write in file name decode routine
eCryptfs: Remove unnecessary casts when parsing packet lengths
eCryptfs: Force RO mount when encrypted view is enabled
Linus Torvalds [Sat, 20 Dec 2014 02:10:42 +0000 (18:10 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/linux-btrfs
Pull more btrfs updates from Chris Mason:
"This is part two of our merge window patches.
These are all from Filipe, and fix some really hard to find races that
can cause corruptions. Most of them involved block group removal
(balance) or discard"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: remove non-sense btrfs_error_discard_extent() function
Btrfs: fix fs corruption on transaction abort if device supports discard
Btrfs: always clear a block group node when removing it from the tree
Btrfs: ensure deletion from pinned_chunks list is protected
Linus Torvalds [Sat, 20 Dec 2014 02:07:17 +0000 (18:07 -0800)]
Merge tag 'sound-fix-3.19-rc1' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a few fixes that have landed after the previous pull request.
All are driver specific fixes including:
- error/int value fixes in OXFW,
- Intel Skylake HD-audio HDMI codec support,
- Additional HD-audio Realtek codecs and
AD1986A codec fixes/quirks,
- a few more DSD support and a quirk for Arcam rPAC in usb-audio,
- a typo fix for Scarlett 6i6,
- fixes for new ASIHPI firmware,
- ASoC Exynos7 cleanups,
- Intel ACPI support, and
- a fix for PCM512 register cache sync"
* tag 'sound-fix-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (24 commits)
ALSA: usb-audio: extend KEF X300A FU 10 tweak to Arcam rPAC
ALSA: hda/realtek - New codec support for ALC298
ALSA: asihpi: update to HPI version 4.14
ALSA: asihpi: increase tuner pad cache size
ALSA: asihpi: relax firmware version check
ALSA: usb-audio: Fix Scarlett 6i6 initialization typo
ALSA: hda - Add quirk for Packard Bell EasyNote MX65
ALSA: usb-audio: add native DSD support for Matrix Audio DACs
ALSA: hda/realtek - New codec support for ALC256
ALSA: hda/realtek - Add new Dell desktop for ALC3234 headset mode
ASoC: Intel: fix possible acpi enumeration panic
ALSA: hda/hdmi - apply Haswell fix-ups to Skylake display codec
ASoC: Intel: fix return value check in sst_acpi_probe()
ALSA: hda - Make add_stereo_mix_input flag tristate
ALSA: hda - Create capture source ctls when stereo mix input is added
ALSA: hda - Fix typos in snd_hda_get_int_hint() kerneldoc comments
ALSA: hda - add codec ID for Skylake display audio codec
ALSA: oxfw: some signedness bugs
ALSA: oxfw: fix detect_loud_models() return value
ASoC: rt5677: add REGMAP_I2C and REGMAP_IRQ dependency
...
Linus Torvalds [Sat, 20 Dec 2014 02:02:22 +0000 (18:02 -0800)]
Merge branch 'for-next' of git://git./linux/kernel/git/nab/target-pending
Pull SCSI target fixes from Nicholas Bellinger:
"The highlights this merge window include:
- Allow target fabric drivers to function as built-in. (Roland)
- Fix tcm_loop multi-TPG endpoint nexus bug. (Hannes)
- Move per device config_item_type into se_subsystem_api, allowing
configfs attributes to be defined at module_init time. (Jerome +
nab)
- Convert existing IBLOCK/FILEIO/RAMDISK/PSCSI/TCMU drivers to use
external configfs attributes. (nab)
- A number of iser-target fixes related to active session + network
portal shutdown stability during extended stress testing. (Sagi +
Slava)
- Dynamic allocation of T10-PI contexts for iser-target, fixing a
potentially bogus iscsi_np->tpg_np pointer reference in >= v3.14
code. (Sagi)
- iser-target performance + scalability improvements. (Sagi)
- Fixes for SPC-4 Persistent Reservation AllRegistrants spec
compliance. (Ilias + James + nab)
- Avoid potential short kern_sendmsg() in iscsi-target for now until
Al's conversion to use msghdr iteration is merged post -rc1.
(Viro)
Also, Sagi has requested a number of iser-target patches (9) that
address stability issues he's encountered during extended stress
testing be considered for v3.10.y + v3.14.y code. Given the amount of
LOC involved, it will certainly require extra backporting effort.
Apologies in advance to Greg-KH & Co on this. Sagi and I will be
working post-merge to ensure they each get applied correctly"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (53 commits)
target: Allow AllRegistrants to re-RESERVE existing reservation
uapi/linux/target_core_user.h: fix headers_install.sh badness
iscsi-target: Fail connection on short sendmsg writes
iscsi-target: nullify session in failed login sequence
target: Avoid dropping AllRegistrants reservation during unregister
target: Fix R_HOLDER bit usage for AllRegistrants
iscsi-target: Drop left-over bogus iscsi_np->tpg_np
iser-target: Fix wc->wr_id cast warning
iser-target: Remove code duplication
iser-target: Adjust log levels and prettify some prints
iser-target: Use debug_level parameter to control logging level
iser-target: Fix logout sequence
iser-target: Don't wait for session commands from completion context
iser-target: Reduce CQ lock contention by batch polling
iser-target: Introduce isert_poll_budget
iser-target: Remove an atomic operation from the IO path
iser-target: Remove redundant call to isert_conn_terminate
iser-target: Use single CQ for TX and RX
iser-target: Centralize completion elements to a context
iser-target: Cast wr_id with uintptr_t instead of unsinged long
...
Linus Torvalds [Sat, 20 Dec 2014 01:57:51 +0000 (17:57 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/rkuo/linux-hexagon-kernel
Pull arch/hexagon updates from Richard Kuo:
"Build cleanup and a few misc fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel:
Hexagon: fix signal delivery for debug traps
Hexagon: set ARCH_DMA_MINALIGN
Hexagon: fix alignment of init_task in RW_DATA_SECTION
hexagon: Fix build failures in linux-next
Linus Torvalds [Sat, 20 Dec 2014 01:08:14 +0000 (17:08 -0800)]
Merge tag 'cris-changes-for-3.19' of git://git./linux/kernel/git/jesper/cris
Pull arch/chris updates from Jesper Nilsson:
"Mostly cleanup and build fixes for CRISv32 allmodconfig
God Jul och Gott Nytt år!"
* tag 'cris-changes-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
CRISv32: Remove last remnants of ETRAX_SPI_MMC_BOARD
CRISv32: ETRAXFS: Fix recursive spinlock
CRISv32: Select MTDRAM for axisflashmap
CRISv32: Implement early console
CRIS: Use KALLSYMs if available in call stack dump
CRISv32: Fix declaration mismatch
CRISv32: Rewrite of synchronous serial port driver
CRIS: Update init memory handling
CRISv32: Better handling of watchdog bite
CRIS: Export missing function symbols
CRIS: Export ioremap_nocache
CRIS: Fix headers_install
CRISv32: Add missing include for mm.h
CRISv32: Drop obsolete file for SPI driver
Linus Torvalds [Sat, 20 Dec 2014 01:07:27 +0000 (17:07 -0800)]
Merge tag 'please-pull-misc-3.19' of git://git./linux/kernel/git/aegl/linux
Pull ia64 __get_cpu_var removal from Tony Luck:
"__get_cpu_var removed from rest of tree, drop reference from comments
in arch/ia64"
* tag 'please-pull-misc-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] Update comment that references __get_cpu_var
Jesper Nilsson [Wed, 29 Oct 2014 09:15:35 +0000 (10:15 +0100)]
CRISv32: Remove last remnants of ETRAX_SPI_MMC_BOARD
There are no users of this symbol left.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Jesper Nilsson [Mon, 27 Oct 2014 08:11:31 +0000 (09:11 +0100)]
CRISv32: ETRAXFS: Fix recursive spinlock
Move pinmux alloc/dealloc code into functions that don't take
the spinlock so we can use from code that has the spinlock already.
CRISv32 has no working SMP, so spinlocks becomes a NOP,
so deadlock was never seen.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Jesper Nilsson [Mon, 27 Oct 2014 08:09:14 +0000 (09:09 +0100)]
CRISv32: Select MTDRAM for axisflashmap
Fixes compile error on allmodconfig.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Jesper Nilsson [Wed, 8 Oct 2014 13:52:49 +0000 (15:52 +0200)]
CRISv32: Implement early console
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Jesper Nilsson [Wed, 8 Oct 2014 12:57:35 +0000 (14:57 +0200)]
CRIS: Use KALLSYMs if available in call stack dump
Also, print kernel version on oops.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Jesper Nilsson [Tue, 7 Oct 2014 11:42:35 +0000 (13:42 +0200)]
CRISv32: Fix declaration mismatch
Drop i2c_init from this header, it was declared non-static here,
but static in the C-file.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Jesper Nilsson [Tue, 7 Oct 2014 11:40:08 +0000 (13:40 +0200)]
CRISv32: Rewrite of synchronous serial port driver
Make driver possible to load as a module and try to handle
locking better.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Jesper Nilsson [Tue, 7 Oct 2014 11:03:17 +0000 (13:03 +0200)]
CRIS: Update init memory handling
- Add free_initrd_mem as found by Guenter Roeck <linux@roeck-us.net>
- Add free_init_pages
- Export empty_zero_page symbol
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Jesper Nilsson [Tue, 7 Oct 2014 10:59:24 +0000 (12:59 +0200)]
CRISv32: Better handling of watchdog bite
Don't enter watchdog handling if we're already in watchdog handling.
Also some minor formatting tweaks.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Jesper Nilsson [Tue, 7 Oct 2014 10:20:47 +0000 (12:20 +0200)]
CRIS: Export missing function symbols
strcmp was lost when all other string functions were removed,
but we still have an optimized version for this on CRISv32,
so any driver built as a module would not have access to this symbol.
In a similar manner, we had optimized versions of
csum_partial_copy_from_user and __do_clear_user
but no exported symbols for them, breaking bunch of other drivers
when built as a module.
At the same time, move EXPORT_SYMBOL(__copy_user) and
EXPORT_SYMBOL(__copy_user_zeroing) C-files so it's
located together with the function definition.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Jesper Nilsson [Wed, 1 Oct 2014 13:38:38 +0000 (15:38 +0200)]
CRIS: Export ioremap_nocache
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Sam Ravnborg [Mon, 14 Jul 2014 15:08:29 +0000 (17:08 +0200)]
CRIS: Fix headers_install
Fix headers_install by adjusting the path to arch files.
And delete unused Kbuild file.
Drop special handling of cris in the headers.sh script
as a nice side-effect.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Jesper Nilsson [Tue, 30 Sep 2014 13:34:10 +0000 (15:34 +0200)]
CRISv32: Add missing include for mm.h
Fixes the following compile error.
arch/cris/arch-v32/kernel/time.c: In function 'reset_watchdog':
arch/cris/arch-v32/kernel/time.c:121:2:
error: implicit declaration of function 'global_page_state'
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Jesper Nilsson [Tue, 30 Sep 2014 13:31:16 +0000 (15:31 +0200)]
CRISv32: Drop obsolete file for SPI driver
File was already deleted.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Linus Torvalds [Fri, 19 Dec 2014 22:02:02 +0000 (14:02 -0800)]
Merge branch 'x86-apic-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 apic updates from Thomas Gleixner:
"After stopping the full x86/apic branch, I took some time to go
through the first block of patches again, which are mostly cleanups
and preparatory work for the irqdomain conversion and ioapic hotplug
support.
Unfortunaly one of the real problematic commits was right at the
beginning, so I rebased this portion of the pending patches without
the offenders.
It would be great to get this into 3.19. That makes reworking the
problematic parts simpler. The usual tip testing did not unearth any
issues and it is fully bisectible now.
I'm pretty confident that this wont affect the calmness of the xmas
season.
Changes:
- Split the convoluted io_apic.c code into domain specific parts
(vector, ioapic, msi, htirq)
- Introduce proper helper functions to retrieve irq specific data
instead of open coded dereferencing of pointers
- Preparatory work for ioapic hotplug and irqdomain conversion
- Removal of the non functional pci-ioapic driver
- Removal of unused irq entry stubs
- Make native_smp_prepare_cpus() preemtible to avoid GFP_ATOMIC
allocations for everything which is called from there.
- Small cleanups and fixes"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
iommu/amd: Use helpers to access irq_cfg data structure associated with IRQ
iommu/vt-d: Use helpers to access irq_cfg data structure associated with IRQ
x86: irq_remapping: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Make MSI and HT_IRQ indepenent of X86_IO_APIC
x86, irq: Move IRQ initialization routines from io_apic.c into vector.c
x86, irq: Move IOAPIC related declarations from hw_irq.h into io_apic.h
x86, irq: Move HT IRQ related code from io_apic.c into htirq.c
x86, irq: Move PCI MSI related code from io_apic.c into msi.c
x86, irq: Replace printk(KERN_LVL) with pr_lvl() utilities
x86, irq: Make UP version of irq_complete_move() an inline stub
x86, irq: Move local APIC related code from io_apic.c into vector.c
x86, irq: Introduce helpers to access struct irq_cfg
x86, irq: Protect __clear_irq_vector() with vector_lock
x86, irq: Rename local APIC related functions in io_apic.c as apic_xxx()
x86, irq: Refine hw_irq.h to prepare for irqdomain support
x86, irq: Convert irq_2_pin list to generic list
x86, irq: Kill useless parameter 'irq_attr' of IO_APIC_get_PCI_irq_vector()
x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI
x86, irq: Introduce helper to check whether an IOAPIC has been registered
...
Rafael J. Wysocki [Fri, 19 Dec 2014 14:37:54 +0000 (15:37 +0100)]
PM: Eliminate CONFIG_PM_RUNTIME
Having switched over all of the users of CONFIG_PM_RUNTIME to use
CONFIG_PM directly, turn the latter into a user-selectable option
and drop the former entirely from the tree.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Linus Torvalds [Fri, 19 Dec 2014 21:29:20 +0000 (13:29 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull NOHZ update from Thomas Gleixner:
"Remove the call into the nohz idle code from the fake 'idle' thread in
the powerclamp driver along with the export of those functions which
was smuggeled in via the thermal tree. People have tried to hack
around it in the nohz core code, but it just violates all rightful
assumptions of that code about the only valid calling context (i.e.
the proper idle task).
The powerclamp trainwreck will still work, it just wont get the
benefit of long idle sleeps"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/powerclamp: Remove tick_nohz_idle abuse
Linus Torvalds [Fri, 19 Dec 2014 21:26:08 +0000 (13:26 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq core fix from Thomas Gleixner:
"A single fix plugging a long standing race between proc/stat and
proc/interrupts access and freeing of interrupt descriptors"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Prevent proc race against freeing of irq descriptors
Linus Torvalds [Fri, 19 Dec 2014 21:22:42 +0000 (13:22 -0800)]
Merge branch 'x86-mpx-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 MPX fixes from Thomas Gleixner:
"Three updates for the new MPX infrastructure:
- Use the proper error check in the trap handler
- Add a proper config option for it
- Bring documentation up to date"
* 'x86-mpx-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, mpx: Give MPX a real config option prompt
x86, mpx: Update documentation
x86_64/traps: Fix always true condition
Linus Torvalds [Fri, 19 Dec 2014 21:18:31 +0000 (13:18 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"This contains a single TLS ABI validation fix from Andy Lutomirski"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tls: Don't validate lm in set_thread_area() after all