OSDN Git Service
Yi Yang [Mon, 28 Aug 2017 19:43:23 +0000 (21:43 +0200)]
net: add NSH header structures and helpers
NSH (Network Service Header)[1] is a new protocol for service
function chaining, it can be handled as a L3 protocol like
IPv4 and IPv6, Eth + NSH + Inner packet or VxLAN-gpe + NSH +
Inner packet are two typical use cases.
This patch adds NSH header structures and helpers for NSH GSO
support and Open vSwitch NSH support.
[1] https://datatracker.ietf.org/doc/draft-ietf-sfc-nsh/
[Jiri: added nsh_hdr() helper and renamed the header struct to "struct
nshhdr" to match the usual pattern. Removed packet type defines, these are
now shared with VXLAN-GPE.]
Signed-off-by: Yi Yang <yi.y.yang@intel.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Mon, 28 Aug 2017 19:43:22 +0000 (21:43 +0200)]
vxlan: factor out VXLAN-GPE next protocol
The values are shared between VXLAN-GPE and NSH. Originally probably by
coincidence but I notified both working groups about this last year and they
seem to keep the values in sync since then.
Hopefully they'll get a single IANA registry for the values, too. (I asked
them for that.)
Factor out the code to be shared by the NSH implementation.
NSH and MPLS values are added in this patch, too. For MPLS, the drafts
incorrectly assign only a single value, while we have two MPLS ethertypes.
I raised the problem with both groups. For now, I assume the value is for
unicast.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Mon, 28 Aug 2017 19:43:21 +0000 (21:43 +0200)]
ether: add NSH ethertype
The NSH draft says:
An IEEE EtherType, 0x894F, has been allocated for NSH.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 29 Aug 2017 22:14:19 +0000 (15:14 -0700)]
Merge branch 'ife-ethertype'
Alexander Aring says:
====================
tc: act_ife: handle IEEE IFE ethertype as default
this patch series will introduce the IFE ethertype which is registered by
IEEE. If the netlink act_ife type netlink attribute is not given it will
use this value by default now.
At least it will introduce some UAPI testcases to check if the default type
is used if not specified and vice versa.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Mon, 28 Aug 2017 19:03:15 +0000 (15:03 -0400)]
tc-testing: add test for testing ife type
This patch adds a new testcase for the IFE type setting in tc. In case
of user specified the type it will check if the ife is correctly
configured to react on it. If it's not specified the default IFE type
should be used.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Mon, 28 Aug 2017 19:03:14 +0000 (15:03 -0400)]
act_ife: use registered ife_type as fallback
This patch handles a default IFE type if it's not given by user space
netlink api. The default IFE type will be the registered ethertype by
IEEE for IFE ForCES.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Mon, 28 Aug 2017 19:03:13 +0000 (15:03 -0400)]
if_ether: add forces ife lfb type
This patch adds the forces IFE lfb type according to IEEE registered
ethertypes. See http://standards-oui.ieee.org/ethertype/eth.txt for more
information. Since there exists the IFE subsystem it can be used there.
This patch also use the correct word "ForCES" instead of "FoRCES" which
is a spelling error inside the IEEE ethertype specification.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 29 Aug 2017 22:07:51 +0000 (15:07 -0700)]
Documentation: networking: Add blurb about patches in patchwork
Explain that the patch queue in patchwork should not be touched by patch
submitters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 29 Aug 2017 21:58:33 +0000 (14:58 -0700)]
Merge branch 'mlx4-misc-patches'
Tariq Toukan says:
====================
mlx4 misc patches
This patchset contains misc patches from the team
to the mlx4 Core and Eth drivers.
Patch 1 by Eran replaces large static allocations by dynamic ones.
Patch 2 by Leon makes an explicit conversion and solves a smatch warning.
In patch 3 I fix a misplaced brackets of the sizeof operation.
Patch 4 by Moshe adds the ability to inform the FW regarding user mac updates.
Series generated against net-next commit:
901c5d2fbfcd ARM: dts: rk3228-evb: Fix the compiling error
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Moshe Shemesh [Mon, 28 Aug 2017 13:38:23 +0000 (16:38 +0300)]
net/mlx4: Add user mac FW update support
Adding support for updating the FW on new port mac, when port mac change
is requested by the user. This info is required by the FW as OEM
management tools require this info directly from the NIC FW.
Check device capability bit to verify the FW supports user mac.
If the FW does support it, use set_port command to notify the FW on the
new mac.
The feature is relevant only to PF port mac.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Mon, 28 Aug 2017 13:38:22 +0000 (16:38 +0300)]
net/mlx4_core: Fix misplaced brackets of sizeof
When changing the sizeof style usage in the patch cited below,
one brackets misplacement was introduced. Here we fix it.
Fixes:
31975e27a4b5 ("mlx4: sizeof style usage")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky [Mon, 28 Aug 2017 13:38:21 +0000 (16:38 +0300)]
net/mlx4_core: Make explicit conversion to 64bit value
The "lg" variable is declared as int so in all places where this variable
is used as a shift operand, the output will be int too.
This produces the following smatch warning:
drivers/net/ethernet/mellanox/mlx4/fw.c:1532 mlx4_map_cmd() warn:
should '1 << lg' be a 64 bit type?
Simple declaration of "1" to be "1ULL" will fix the issue.
Fixes:
225c7b1feef1 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha [Mon, 28 Aug 2017 13:38:20 +0000 (16:38 +0300)]
net/mlx4_core: Dynamically allocate structs at mlx4_slave_cap
In order to avoid temporary large structs on the stack,
allocate them dynamically.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tal Alon <talal@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu [Tue, 29 Aug 2017 20:16:57 +0000 (13:16 -0700)]
bridge: fdb add and delete tracepoints
A few useful tracepoints to trace bridge forwarding
database updates.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 29 Aug 2017 21:42:17 +0000 (14:42 -0700)]
Merge branch 'systemport-sf2-mdio-endian'
Florian Fainelli says:
====================
Endian fixes for SYSTEMPORT/SF2/MDIO
While trying an ARM BE kernel for kinks, the 3 drivers below started not
working and the reasons why became pretty obvious because the register space
remains LE (hardwired), except for Broadcom MIPS where it follows the CPU's
native endian (let's call that a feature).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 29 Aug 2017 20:35:18 +0000 (13:35 -0700)]
net: phy: mdio-bcm-unimac: Use correct I/O accessors
The driver currently uses __raw_{read,write}l which works for all
platforms supported: Broadcom MIPS LE/BE (native endian), ARM LE (native
endian) but not ARM BE (registers are still LE). Switch to using the
proper accessors for all platforms and explain why Broadcom MIPS BE is
special here, in doing so, we introduce a couple of helper functions to
abstract these differences.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 29 Aug 2017 20:35:17 +0000 (13:35 -0700)]
net: systemport: Set correct RSB endian bits based on host
RSB_SWAP0 needs to match the host CPU endian, and it needs to be set
for LE and clear for BE. RSB_SWAP1 must always be cleared for SYSTEMPORT
Lite.
With these settings, we have the Receive Status Block always match the
host endian and we do not need to perform any conversion. Since there is
not necessarily a CONFIG_CPU_LITTLE_ENDIAN option defined, we test for
!CONFIG_CPU_BIG_ENDIAN which is guaranteed to be set.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 29 Aug 2017 20:35:16 +0000 (13:35 -0700)]
net: dsa: bcm_sf2: Use correct I/O accessors
The Starfigther 2 driver currently uses __raw_{read,write}l which means
native I/O endian. This works correctly for an ARM LE kernel (default)
but fails miserably on an ARM BE (BE8) kernel where registers are kept
little endian, so replace uses with {read,write}l_relaxed here which is
what we want because this is all performance sensitive code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 29 Aug 2017 20:35:15 +0000 (13:35 -0700)]
net: systemport: Use correct I/O accessors
The SYSTEMPORT driver currently uses __raw_{read,write}l which means
native I/O endian. This works correctly for an ARM LE kernel (default)
but fails miserably on an ARM BE (BE8) kernel where registers are kept
little endian, so replace uses with {read,write}l_relaxed here which is
what we want because this is all performance sensitive code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 29 Aug 2017 18:04:43 +0000 (11:04 -0700)]
Merge tag 'wireless-drivers-next-for-davem-2017-08-28' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.14
rsi driver is getting a lot of new features lately, but as usual
active development happening on iwlwifi as well as other drivers.
I pulled wireless-drivers to fix multiple conflicts in iwlwifi and to
make it easier further development.
Major changes:
ath10k
* initial UBS bus support (no full support yet)
* add tdls support for 10.4 firmware
ath9k
* add Dell Wireless 1802
wil6210
* support FW RSSI reporting
rsi
* support legacy power save, U-APSD, rf-kill and AP mode
* RTS threshold configuration
brcmfmac
* support CYW4373 SDIO/USB chipset
iwlwifi
* some more code moved to a new directory
* add new PCI ID for 7265D
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Yadav [Mon, 28 Aug 2017 05:52:20 +0000 (11:22 +0530)]
net: stmmac: constify clk_div_table
clk_div_table are not supposed to change at runtime.
meson8b_dwmac structure is working with const clk_div_table.
So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 29 Aug 2017 17:51:29 +0000 (10:51 -0700)]
Merge branch 'XDP-redirect-tracepoints'
Jesper Dangaard Brouer says:
====================
XDP redirect tracepoints
I feel this is as far as I can take the tracepoint infrastructure to
assist XDP monitoring.
Tracepoints comes with a base overhead of 25 nanosec for an attached
bpf_prog, and 48 nanosec for using a full perf record. This is
problematic for the XDP use-case, but it is very convenient to use the
existing perf infrastructure.
From a performance perspective, the real solution would be to attach
another bpf_prog (that understand xdp_buff), but I'm not sure we want
to introduce yet another bpf attach API for this.
One thing left is to standardize the possible err return codes, to a
limited set, to allow easier (and faster) mapping into a bpf map.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer [Tue, 29 Aug 2017 14:38:11 +0000 (16:38 +0200)]
samples/bpf: xdp_monitor tool based on tracepoints
This tool xdp_monitor demonstrate how to use the different xdp_redirect
tracepoints xdp_redirect{,_map}{,_err} from a BPF program.
The default mode is to only monitor the error counters, to avoid
affecting the per packet performance. Tracepoints comes with a base
overhead of 25 nanosec for an attached bpf_prog, and 48 nanosec for
using a full perf record (with non-matching filter). Thus, default
loading the --stats mode could affect the maximum performance.
This version of the tool is very simple and count all types of errors
as one. It will be natural to extend this later with the different
types of errors that can occur, which should help users quickly
identify common mistakes.
Because the TP_STRUCT was kept in sync all the tracepoints loads the
same BPF code. It would also be natural to extend the map version to
demonstrate how the map information could be used.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer [Tue, 29 Aug 2017 14:38:06 +0000 (16:38 +0200)]
samples/bpf: xdp_redirect load XDP dummy prog on TX device
For supporting XDP_REDIRECT, a device driver must (obviously)
implement the "TX" function ndo_xdp_xmit(). An additional requirement
is you cannot TX out a device, unless it also have a xdp bpf program
attached. This dependency is caused by the driver code need to setup
XDP resources before it can ndo_xdp_xmit.
Update bpf samples xdp_redirect and xdp_redirect_map to automatically
attach a dummy XDP program to the configured ifindex_out device. Use
the XDP flag XDP_FLAGS_UPDATE_IF_NOEXIST on the dummy load, to avoid
overriding an existing XDP prog on the device.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer [Tue, 29 Aug 2017 14:38:01 +0000 (16:38 +0200)]
xdp: separate xdp_redirect tracepoint in map case
Creating as specific xdp_redirect_map variant of the xdp tracepoints
allow users to write simpler/faster BPF progs that get attached to
these tracepoints.
Goal is to still keep the tracepoints in xdp_redirect and xdp_redirect_map
similar enough, that a tool can read the top part of the TP_STRUCT and
produce similar monitor statistics.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer [Tue, 29 Aug 2017 14:37:56 +0000 (16:37 +0200)]
xdp: separate xdp_redirect tracepoint in error case
There is a need to separate the xdp_redirect tracepoint into two
tracepoints, for separating the error case from the normal forward
case.
Due to the extreme speeds XDP is operating at, loading a tracepoint
have a measurable impact. Single core XDP REDIRECT (ethtool tuned
rx-usecs 25) can do 13.7 Mpps forwarding, but loading a simple
bpf_prog at the tracepoint (with a return 0) reduce perf to 10.2 Mpps
(CPU E5-1650 v4 @ 3.60GHz, driver: ixgbe)
The overhead of loading a bpf-based tracepoint can be calculated to
cost 25 nanosec ((1/
13782002-1/
10267937)*10^9 = -24.83 ns).
Using perf record on the tracepoint event, with a non-matching --filter
expression, the overhead is much larger. Performance drops to 8.3 Mpps,
cost 48 nanosec ((1/
13782002-1/
8312497)*10^9 = -47.74))
Having a separate tracepoint for err cases, which should be less
frequent, allow running a continuous monitor for errors while not
affecting the redirect forward performance (this have also been
verified by measurements).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer [Tue, 29 Aug 2017 14:37:51 +0000 (16:37 +0200)]
xdp: make xdp tracepoints report bpf prog id instead of prog_tag
Given previous patch expose the map_id, it seems natural to also
report the bpf prog id.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer [Tue, 29 Aug 2017 14:37:45 +0000 (16:37 +0200)]
xdp: tracepoint xdp_redirect also need a map argument
To make sense of the map index, the tracepoint user also need to know
that map we are talking about. Supply the map pointer but only expose
the map->id.
The 'to_index' is renamed 'to_ifindex'. In the xdp_redirect_map case,
this is the result of the devmap lookup. The map lookup key is exposed
as map_index, which is needed to troubleshoot in case the lookup failed.
The 'to_ifindex' is placed after 'err' to keep TP_STRUCT as common as
possible.
This also keeps the TP_STRUCT similar enough, that userspace can write
a monitor program, that doesn't need to care about whether
bpf_redirect or bpf_redirect_map were used.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer [Tue, 29 Aug 2017 14:37:40 +0000 (16:37 +0200)]
xdp: remove redundant argument to trace_xdp_redirect
Supplying the action argument XDP_REDIRECT to the tracepoint xdp_redirect
is redundant as it is only called in-case this action was specified.
Remove the argument, but keep "act" member of the tracepoint struct and
populate it with XDP_REDIRECT. This makes it easier to write a common bpf_prog
processing events.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 29 Aug 2017 16:42:48 +0000 (09:42 -0700)]
Merge tag 'rxrpc-next-
20170829' of git://git./linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Miscellany
Here are a number of patches that make some changes/fixes and add a couple
of extensions to AF_RXRPC for kernel services to use. The changes and
fixes are:
(1) Use time64_t rather than u32 outside of protocol or
UAPI-representative structures.
(2) Use the correct time stamp when loading a key from an XDR-encoded
Kerberos 5 key.
(3) Fix IPv6 support.
(4) Fix some places where the error code is being incorrectly made
positive before returning.
(5) Remove some white space.
And the extensions:
(6) Add an end-of-Tx phase notification, thereby allowing kAFS to
transition the state on its own call record at the correct point,
rather than having to do it in advance and risk non-completion of the
call in the wrong state.
(7) Allow a kernel client call to be retried if it fails on a network
error, thereby making it possible for kAFS to iterate over a number of
IP addresses without having to reload the Tx queue and re-encrypt data
each time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 29 Aug 2017 16:41:56 +0000 (09:41 -0700)]
Merge branch 'addrlabel-no-rtnl-locking'
Florian Westphal says:
====================
addrlabel: don't use rtnl locking
addrlabel doesn't appear to require rtnl lock as the addrlabel
table uses a spinlock to serialize add/delete operations.
Also, entries are reference counted so it should be safe
to call the rtnl ops without the rtnl mutex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Tue, 29 Aug 2017 11:29:42 +0000 (13:29 +0200)]
addrlabel: add/delete/get can run without rtnl
There appears to be no need to use rtnl, addrlabel entries are refcounted
and add/delete is serialized by the addrlabel table spinlock.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Tue, 29 Aug 2017 11:29:41 +0000 (13:29 +0200)]
selftests: add addrlabel add/delete to rtnetlink.sh
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Kroah-Hartman [Tue, 29 Aug 2017 07:09:29 +0000 (09:09 +0200)]
staging: irda: update MAINTAINERS
Now that the IRDA code has moved under drivers/staging/irda/, update the
MAINTAINERS file with the new location.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Tue, 29 Aug 2017 06:15:03 +0000 (11:45 +0530)]
bnxt_en: add a dummy definition for bnxt_vf_rep_get_fid()
When bnxt VF-reps are not compiled in (CONFIG_BNXT_SRIOV is off)
bnxt_tc.c needs a dummy definition of the routine bnxt_vf_rep_get_fid().
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes:
2ae7408fedfe ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Tue, 29 Aug 2017 09:19:01 +0000 (10:19 +0100)]
rxrpc: Allow failed client calls to be retried
Allow a client call that failed on network error to be retried, provided
that the Tx queue still holds DATA packet 1. This allows an operation to
be submitted to another server or another address for the same server
without having to repackage and re-encrypt the data so far processed.
Two new functions are provided:
(1) rxrpc_kernel_check_call() - This is used to find out the completion
state of a call to guess whether it can be retried and whether it
should be retried.
(2) rxrpc_kernel_retry_call() - Disconnect the call from its current
connection, reset the state and submit it as a new client call to a
new address. The new address need not match the previous address.
A call may be retried even if all the data hasn't been loaded into it yet;
a partially constructed will be retained at the same point it was at when
an error condition was detected. msg_data_left() can be used to find out
how much data was packaged before the error occurred.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Tue, 29 Aug 2017 09:18:56 +0000 (10:18 +0100)]
rxrpc: Add notification of end-of-Tx phase
Add a callback to rxrpc_kernel_send_data() so that a kernel service can get
a notification that the AF_RXRPC call has transitioned out the Tx phase and
is now waiting for a reply or a final ACK.
This is called from AF_RXRPC with the call state lock held so the
notification is guaranteed to come before any reply is passed back.
Further, modify the AFS filesystem to make use of this so that we don't have
to change the afs_call state before sending the last bit of data.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Tue, 29 Aug 2017 09:18:50 +0000 (10:18 +0100)]
rxrpc: Remove some excess whitespace
Remove indentation from some blank lines.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Tue, 29 Aug 2017 09:18:43 +0000 (10:18 +0100)]
rxrpc: Don't negate call->error before returning it
call->error is stored as 0 or a negative error code. Don't negate this
value (ie. make it positive) before returning it from a kernel function
(though it should still be negated before passing to userspace through a
control message).
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Tue, 29 Aug 2017 09:18:37 +0000 (10:18 +0100)]
rxrpc: Fix IPv6 support
Fix IPv6 support in AF_RXRPC in the following ways:
(1) When extracting the address from a received IPv4 packet, if the local
transport socket is open for IPv6 then fill out the sockaddr_rxrpc
struct for an IPv4-mapped-to-IPv6 AF_INET6 transport address instead
of an AF_INET one.
(2) When sending CHALLENGE or RESPONSE packets, the transport length needs
to be set from the sockaddr_rxrpc::transport_len field rather than
sizeof() on the IPv4 transport address.
(3) When processing an IPv4 ICMP packet received by an IPv6 socket, set up
the address correctly before searching for the affected peer.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Tue, 29 Aug 2017 09:15:40 +0000 (10:15 +0100)]
rxrpc: Use correct timestamp from Kerberos 5 ticket
When an XDR-encoded Kerberos 5 ticket is added as an rxrpc-type key, the
expiry time should be drawn from the k5 part of the token union (which was
what was filled in), rather than the kad part of the union.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Baolin Wang [Tue, 29 Aug 2017 09:15:40 +0000 (10:15 +0100)]
net: rxrpc: Replace time_t type with time64_t type
Since the 'expiry' variable of 'struct key_preparsed_payload' has been
changed to 'time64_t' type, which is year 2038 safe on 32bits system.
In net/rxrpc subsystem, we need convert 'u32' type to 'time64_t' type
when copying ticket expires time to 'prep->expiry', then this patch
introduces two helper functions to help convert 'u32' to 'time64_t'
type.
This patch also uses ktime_get_real_seconds() to get current time instead
of get_seconds() which is not year 2038 safe on 32bits system.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Vitaly Kuznetsov [Mon, 28 Aug 2017 13:16:05 +0000 (15:16 +0200)]
hinic: don't build the module by default
We probably don't want to enable code supporting particular hardware by
default e.g. when someone does 'make defconfig'. Other ethernet modules
don't do it.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Aug 2017 23:57:10 +0000 (16:57 -0700)]
Merge branch 'bnxt_en-next'
Michael Chan says:
====================
bnxt_en: Updates.
Various changes including updated firmware interface, improved TX ring
allocation scheme, improved out-of-memory logic in NAPI loop, reduced
default rings on multi-port devices, new PCI IDs. Of particular note,
CPU affinity hints from Vasundhara Volam.
TC Flower eswitch support from Sathya Perla.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Mon, 28 Aug 2017 17:40:35 +0000 (13:40 -0400)]
bnxt_en: add code to query TC flower offload stats
This patch adds code to implement TC_CLSFLOWER_STATS TC-cmd and the
required FW code to query the stats from the HW.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Mon, 28 Aug 2017 17:40:34 +0000 (13:40 -0400)]
bnxt_en: add TC flower offload flow_alloc/free FW cmds
This patch adds the hwrm_cfa_flow_alloc/free() routines
that are needed to issue the FW cmds needed for TC flower offload.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Mon, 28 Aug 2017 17:40:33 +0000 (13:40 -0400)]
bnxt_en: bnxt: add TC flower filter offload support
This patch adds support for offloading TC based flow
rules and actions for the 'flower' classifier in the bnxt_en driver.
It includes logic to parse flow rules and actions received from the
TC subsystem, store them and issue the corresponding
hwrm_cfa_flow_alloc/free FW cmds. L2/IPv4/IPv6 flows and drop,
redir, vlan push/pop actions are supported in this patch.
In this patch the hwrm_cfa_flow_xxx routines are just stubs.
The code for these routines is introduced in the next patch for easier
review. Also, the code to query the TC/flower action stats will
be introduced in a subsequent patch.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Mon, 28 Aug 2017 17:40:32 +0000 (13:40 -0400)]
bnxt_en: fix clearing devlink ptr from bnxt struct
The routine bnxt_link_bp_to_dl() is used to set the devlink ptr
in bnxt struct (bp) and also to set the bnxt back ptr in
the devlink struct. If devlink_register() fails, bp->dl must
be cleared which is not happening currently. This patch fixes
bnxt_link_bp_to_dl() to clear bp->dl by passing a NULL dl ptr.
Fixes:
4ab0c6a8ffd7 ("bnxt_en: add support to enable VF-representors")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 28 Aug 2017 17:40:31 +0000 (13:40 -0400)]
bnxt_en: Reduce default rings on multi-port cards.
Reduce default rings from 8 to 4 on multi-port cards to reduce memory
usage.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 28 Aug 2017 17:40:30 +0000 (13:40 -0400)]
bnxt_en: Improve -ENOMEM logic in NAPI poll loop.
If we cannot allocate RX buffers in the NAPI poll loop when processing
an RX event, the current code does not count that event towards the NAPI
budget. This can cause us to potentially loop forever in NAPI if we
consistently cannot allocate new buffers. Improve it by counting
-ENOMEM event as 1 towards the NAPI budget.
Cc: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reported-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Branden [Mon, 28 Aug 2017 17:40:29 +0000 (13:40 -0400)]
bnxt: initialize board_info values with proper enums
initialize board_info values with proper enums for defensive programming
purposes. This will avoid any errors of the enums being declared not
lining up with the board_info array.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ray Jui [Mon, 28 Aug 2017 17:40:28 +0000 (13:40 -0400)]
bnxt: Add PCIe device IDs for bcm58802/bcm58808
Add PCIe device ID for bcm58802 and bcm58808. Also add chip number
update to declare bcm588xx as chip class phase 4 and later
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Mon, 28 Aug 2017 17:40:27 +0000 (13:40 -0400)]
bnxt_en: assign CPU affinity hints to bnxt_en IRQs
This patch provides hints to irqbalance to map bnxt_en device IRQs
to specific CPU cores. cpumask_local_spread() is used, which first
maps IRQs to near NUMA cores; when those cores are exhausted, IRQs
are mapped to far NUMA cores.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 28 Aug 2017 17:40:26 +0000 (13:40 -0400)]
bnxt_en: Improve tx ring reservation logic.
When the number of TX rings is changed (e.g. ethtool -L, enabling XDP TX
rings, etc), the current code tries to reserve the new number of TX rings
before closing and re-opening the NIC. If we are unable to reserve the
new TX rings, we abort the operation and keep the current TX rings.
The problem is that the firmware will disable the current TX rings even
when it cannot reserve the new set of TX rings. We fix it as follows:
1. Instead of reserving the new set of TX rings, just ask the firmware
to check if the new set of TX rings is available. There is a flag in
the firmware message to do that. If not available, abort and the
current TX rings will not be disabled.
2. Do the actual TX ring reservation in the path that opens the NIC.
We keep the number of TX rings currently successfully reserved. If the
number of TX rings is different than the reserved TX rings, we call
firmware and reserve again.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 28 Aug 2017 17:40:25 +0000 (13:40 -0400)]
bnxt_en: Update firmware interface spec. to 1.8.1.4.
Flow APIs are added in this firmware interface.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Aug 2017 23:49:49 +0000 (16:49 -0700)]
Merge branch 'NCSI-vlan-filtering'
Samuel Mendoza-Jonas says:
====================
NCSI VLAN Filtering Support
This series (mainly patch 2) adds VLAN filtering to the NCSI implementation.
A fair amount of code already exists in the NCSI stack for VLAN filtering but
none of it is actually hooked up. This goes the final mile and fixes a few
bugs in the existing code found along the way (patch 1).
Patch 3 adds the appropriate flag and callbacks to the ftgmac100 driver to
enable filtering as it's a large consumer of NCSI (and what I've been
testing on).
v3: - Add comment describing change to ncsi_find_filter()
- Catch NULL in clear_one_vid() from ncsi_get_filter()
- Simplify state changes when kicking updated channel
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Samuel Mendoza-Jonas [Mon, 28 Aug 2017 06:18:43 +0000 (16:18 +1000)]
ftgmac100: Support NCSI VLAN filtering when available
Register the ndo_vlan_rx_{add,kill}_vid callbacks and set the
NETIF_F_HW_VLAN_CTAG_FILTER if NCSI is available.
This allows the VLAN core to notify the NCSI driver when changes occur
so that the remote NCSI channel can be properly configured to filter on
the set VLAN tags.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Samuel Mendoza-Jonas [Mon, 28 Aug 2017 06:18:42 +0000 (16:18 +1000)]
net/ncsi: Configure VLAN tag filter
Make use of the ndo_vlan_rx_{add,kill}_vid callbacks to have the NCSI
stack process new VLAN tags and configure the channel VLAN filter
appropriately.
Several VLAN tags can be set and a "Set VLAN Filter" packet must be sent
for each one, meaning the ncsi_dev_state_config_svf state must be
repeated. An internal list of VLAN tags is maintained, and compared
against the current channel's ncsi_channel_filter in order to keep track
within the state. VLAN filters are removed in a similar manner, with the
introduction of the ncsi_dev_state_config_clear_vids state. The maximum
number of VLAN tag filters is determined by the "Get Capabilities"
response from the channel.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Samuel Mendoza-Jonas [Mon, 28 Aug 2017 06:18:41 +0000 (16:18 +1000)]
net/ncsi: Fix several packet definitions
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Aug 2017 23:46:25 +0000 (16:46 -0700)]
Merge branch '40GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-08-27
This series contains updates to i40e and i40evf only.
Sudheer updates code comments and state variable so that adminq_subtask
will have accutate information whenever it gets scheduled.
Mariusz stores information about FEC modes, to be used to printing link
states information, so that we do not need to call admin queue when
reporting link status. Adds VF support for controlling VLAN tag
stripping via ethtool.
Jake provides the majority of changes in this series, starting with
increasing the size of the prefix buffer so that it can hold enough
characters for every possible input, which prevents snprintf truncation.
Fixed other string truncation errors/warnings produced by GCC 7.x.
Removed an unnecessary workaround for resetting XPS. Fixed an issue
where there is a mismatched affinity mask value, so initialize the value
to cpu_possible_mask and invert the logic for checking incorrect CPU vs
IRQ affinity so that the exceptional case is handled at the check.
Removed ULTRA latency mode due to several issues found and will be
looking at better solution for small packet workloads.
Akeem fixes an issue where the incorrect flag was being used to set
promiscuous mode for unicast, which was enabling promiscuous mode only
for multicast instead of unicast.
Carolyn fixes an issue where an error return value is set, but this
value can be overwritten before we actually do exit the function. So
remove the error code assignment and add code comments for better
understanding on why we do not need to set and return the error.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Sun, 27 Aug 2017 17:35:30 +0000 (01:35 +0800)]
net-next/hinic: fix comparison of a uint16_t type with -1
Remove the search for index of constant buffer size
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Sun, 27 Aug 2017 17:20:26 +0000 (01:20 +0800)]
net-next/hinic: Fix MTU limitation
Fix the hw MTU limitation by setting max_mtu
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Aug 2017 23:42:57 +0000 (16:42 -0700)]
Merge branch 'irda-move-to-staging'
Greg Kroah-Hartman says:
====================
irda: move it to drivers/staging so we can delete it
The IRDA code has long been obsolete and broken. So, to keep people
from trying to use it, and to prevent people from having to maintain it,
let's move it to drivers/staging/ so that we can delete it entirely from
the kernel in a few releases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Kroah-Hartman [Sun, 27 Aug 2017 15:03:34 +0000 (17:03 +0200)]
staging: irda: add a TODO file.
The irda code will be deleted in a future kernel release, so no need to
have anyone do any new work on it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Kroah-Hartman [Sun, 27 Aug 2017 15:03:33 +0000 (17:03 +0200)]
irda: move include/net/irda into staging subdirectory
And finally, move the irda include files into
drivers/staging/irda/include/net/irda. Yes, it's a long path, but it
makes it easy for us to just add a Makefile directory path addition and
all of the net and drivers code "just works".
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Kroah-Hartman [Sun, 27 Aug 2017 15:03:32 +0000 (17:03 +0200)]
irda: move drivers/net/irda to drivers/staging/irda/drivers
Move the irda drivers from drivers/net/irda/ to
drivers/staging/irda/drivers as they will be deleted in a future kernel
release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Kroah-Hartman [Sun, 27 Aug 2017 15:03:31 +0000 (17:03 +0200)]
irda: move net/irda/ to drivers/staging/irda/net/
It's time to get rid of IRDA. It's long been broken, and no one seems
to use it anymore. So move it to staging and after a while, we can
delete it from there.
To start, move the network irda core from net/irda to
drivers/staging/irda/net/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Aug 2017 23:41:01 +0000 (16:41 -0700)]
Merge branch 'dpaa_eth-rss'
Madalin Bucur says:
====================
Add RSS to DPAA 1.x Ethernet driver
This patch set introduces Receive Side Scaling for the DPAA Ethernet
driver. Documentation is updated with details related to the new
feature and limitations that apply.
Added also a small fix.
v2: removed a C++ style comment
v3: move struct fman to header file to avoid exporting a function
v4: addressed compilation issues introduced in v3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Sun, 27 Aug 2017 13:13:43 +0000 (16:13 +0300)]
dpaa_eth: check allocation result
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Sun, 27 Aug 2017 13:13:42 +0000 (16:13 +0300)]
Documentation: networking: add RSS information
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Sun, 27 Aug 2017 13:13:41 +0000 (16:13 +0300)]
dpaa_eth: add NETIF_F_RXHASH
Set the skb hash when then FMan Keygen hash result is available.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Sun, 27 Aug 2017 13:13:40 +0000 (16:13 +0300)]
dpaa_eth: enable Rx hashing control
Allow ethtool control of the Rx flow hashing. By default RSS is
enabled, this allows to turn it off by bypassing the FMan Keygen
block and sending all traffic on the default Rx frame queue.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Sun, 27 Aug 2017 13:13:39 +0000 (16:13 +0300)]
dpaa_eth: use multiple Rx frame queues
Add a block of 128 Rx frame queues per port. The FMan hardware will
send traffic on one of these queues based on the FMan port Parse
Classify Distribute setup. The hash computed by the FMan Keygen
block will select the Rx FQ.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Iordache Florinel-R70177 [Sun, 27 Aug 2017 13:13:38 +0000 (16:13 +0300)]
fsl/fman: enable FMan Keygen
Add support for the FMan Keygen with a hardcoded scheme to spread
incoming traffic on a FQ range based on source and destination IPs
and ports.
Signed-off-by: Iordache Florinel <florinel.iordache@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Sun, 27 Aug 2017 13:13:37 +0000 (16:13 +0300)]
fsl/fman: move struct fman to header file
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Himanshu Jha [Sat, 26 Aug 2017 20:17:47 +0000 (01:47 +0530)]
net: ethernet: broadcom: Remove null check before kfree
Kfree on NULL pointer is a no-op and therefore checking is redundant.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gao Feng [Sat, 26 Aug 2017 14:58:58 +0000 (22:58 +0800)]
sched: sfq: drop packets after root qdisc lock is released
The commit
520ac30f4551 ("net_sched: drop packets after root qdisc lock
is released) made a big change of tc for performance. But there are
some points which are not changed in SFQ enqueue operation.
1. Fail to find the SFQ hash slot;
2. When the queue is full;
Now use qdisc_drop instead free skb directly.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Aug 2017 22:41:15 +0000 (15:41 -0700)]
Merge branch 'mlxsw-dpipe-fixes'
Jiri Pirko says:
====================
mlxsw: spectrum: Fix couple of dpipe ipv4 host table bugs
Arkadi Sharshevsky (1):
mlxsw: spectrum_dpipe: Fix host table dump
Jiri Pirko (1):
mlxsw: spectrum: compile-in dpipe support only if devlink is enabled
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Arkadi Sharshevsky [Sat, 26 Aug 2017 06:35:39 +0000 (08:35 +0200)]
mlxsw: spectrum_dpipe: Fix host table dump
During the neighbor traversal the neighbors from different families
should be ignored.
Fixes:
c58035a74aba ("mlxsw: spectrum_dpipe: Add support for IPv4 host table dump")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Sat, 26 Aug 2017 06:35:38 +0000 (08:35 +0200)]
mlxsw: spectrum: compile-in dpipe support only if devlink is enabled
Makes no sense to have dpipe compiled in when devlink is not enabled,
because the devlink dpipe registation is noop function. So don't compile
it in. This also fixes missing extern structs errors.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes:
a86f030915f2 ("mlxsw: spectrum_dpipe: Add support for IPv4 host table dump")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dexuan Cui [Sat, 26 Aug 2017 04:52:43 +0000 (04:52 +0000)]
hv_sock: implements Hyper-V transport for Virtual Sockets (AF_VSOCK)
Hyper-V Sockets (hv_sock) supplies a byte-stream based communication
mechanism between the host and the guest. It uses VMBus ringbuffer as the
transportation layer.
With hv_sock, applications between the host (Windows 10, Windows Server
2016 or newer) and the guest can talk with each other using the traditional
socket APIs.
More info about Hyper-V Sockets is available here:
"Make your own integration services":
https://docs.microsoft.com/en-us/virtualization/hyper-v-on-windows/user-guide/make-integration-service
The patch implements the necessary support in Linux guest by introducing a new
vsock transport for AF_VSOCK.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Andy King <acking@vmware.com>
Cc: Dmitry Torokhov <dtor@vmware.com>
Cc: George Zhang <georgezhang@vmware.com>
Cc: Jorgen Hansen <jhansen@vmware.com>
Cc: Reilly Grant <grantr@vmware.com>
Cc: Asias He <asias@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Cathy Avery <cavery@redhat.com>
Cc: Rolf Neugebauer <rolf.neugebauer@docker.com>
Cc: Marcelo Cerri <marcelo.cerri@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 25 Aug 2017 21:39:57 +0000 (14:39 -0700)]
selftests/bpf: check the instruction dumps are populated
Add a basic test for checking whether kernel is populating
the jited and xlated BPF images. It was used to confirm
the behaviour change from commit
d777b2ddbecf ("bpf: don't
zero out the info struct in bpf_obj_get_info_by_fd()"),
which made bpf_obj_get_info_by_fd() usable for retrieving
the image dumps.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 25 Aug 2017 20:27:14 +0000 (23:27 +0300)]
bpf: fix oops on allocation failure
"err" is set to zero if bpf_map_area_alloc() fails so it means we return
ERR_PTR(0) which is NULL. The caller, find_and_alloc_map(), is not
expecting NULL returns and will oops.
Fixes:
174a79ff9515 ("bpf: sockmap with sk redirect support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 28 Aug 2017 22:14:20 +0000 (15:14 -0700)]
net: Add comment that early_demux can change via sysctl
Twice patches trying to constify inet{6}_protocol have been reverted:
39294c3df2a8 ("Revert "ipv6: constify inet6_protocol structures"") to
revert
3a3a4e3054137 and then
03157937fe0b5 ("Revert "ipv4: make
net_protocol const"") to revert
aa8db499ea67.
Add a comment that the structures can not be const because the
early_demux field can change based on a sysctl.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Fri, 25 Aug 2017 17:10:43 +0000 (13:10 -0400)]
xen-netback: update ubuf_info initialization to anonymous union
The xen driver initializes struct ubuf_info fields using designated
initializers. I recently moved these fields inside a nested anonymous
struct inside an anonymous union. I had missed this use case.
This breaks compilation of xen-netback with older compilers.
>From kbuild bot with gcc-4.4.7:
drivers/net//xen-netback/interface.c: In function
'xenvif_init_queue':
>> drivers/net//xen-netback/interface.c:554: error: unknown field 'ctx' specified in initializer
>> drivers/net//xen-netback/interface.c:554: warning: missing braces around initializer
drivers/net//xen-netback/interface.c:554: warning: (near initialization for '(anonymous).<anonymous>')
>> drivers/net//xen-netback/interface.c:554: warning: initialization makes integer from pointer without a cast
>> drivers/net//xen-netback/interface.c:555: error: unknown field 'desc' specified in initializer
Add double braces around the designated initializers to match their
nested position in the struct. After this, compilation succeeds again.
Fixes:
4ab6c99d99bb ("sock: MSG_ZEROCOPY notification coalescing")
Reported-by: kbuild bot <lpk@intel.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Aug 2017 22:04:52 +0000 (15:04 -0700)]
Merge branch 'gre-add-collect_md-mode-for-ERSPAN-tunnel'
William Tu says:
====================
gre: add collect_md mode for ERSPAN tunnel
This patch series provide collect_md mode for ERSPAN tunnel. The fist patch
refactors the existing gre_fb_xmit function by exacting the route cache
portion into a new function called prepare_fb_xmit. The second patch
introduces the collect_md mode for ERSPAN tunnel, by calling the
prepare_fb_xmit function and adding ERSPAN specific logic. The final patch
adds the test case using bpf_skb_{set,get}_tunnel_{key,opt}.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
William Tu [Fri, 25 Aug 2017 16:21:29 +0000 (09:21 -0700)]
samples/bpf: extend test_tunnel_bpf.sh with ERSPAN
Extend existing tests for vxlan, gre, geneve, ipip to
include ERSPAN tunnel.
Signed-off-by: William Tu <u9012063@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
William Tu [Fri, 25 Aug 2017 16:21:28 +0000 (09:21 -0700)]
gre: add collect_md mode to ERSPAN tunnel
Similar to gre, vxlan, geneve, ipip tunnels, allow ERSPAN tunnels to
operate in 'collect metadata' mode. bpf_skb_[gs]et_tunnel_key() helpers
can make use of it right away. OVS can use it as well in the future.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
William Tu [Fri, 25 Aug 2017 16:21:27 +0000 (09:21 -0700)]
gre: refactor the gre_fb_xmit
The patch refactors the gre_fb_xmit function, by creating
prepare_fb_xmit function for later ERSPAN collect_md mode patch.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 28 Aug 2017 20:23:09 +0000 (13:23 -0700)]
Revert "ipv4: make net_protocol const"
This reverts commit
aa8db499ea67cff1f5f049033810ffede2fe5ae4.
Early demux structs can not be made const. Doing so results in:
[ 84.967355] BUG: unable to handle kernel paging request at
ffffffff81684b10
[ 84.969272] IP: proc_configure_early_demux+0x1e/0x3d
[ 84.970544] PGD
1a0a067
[ 84.970546] P4D
1a0a067
[ 84.971212] PUD
1a0b063
[ 84.971733] PMD
80000000016001e1
[ 84.972669] Oops: 0003 [#1] SMP
[ 84.973065] Modules linked in: ip6table_filter ip6_tables veth vrf
[ 84.973833] CPU: 0 PID: 955 Comm: sysctl Not tainted 4.13.0-rc6+ #22
[ 84.974612] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 84.975855] task:
ffff88003854ce00 task.stack:
ffffc900005a4000
[ 84.976580] RIP: 0010:proc_configure_early_demux+0x1e/0x3d
[ 84.977253] RSP: 0018:
ffffc900005a7dd0 EFLAGS:
00010246
[ 84.977891] RAX:
ffffffff81684b10 RBX:
0000000000000001 RCX:
0000000000000000
[ 84.978759] RDX:
0000000000000000 RSI:
0000000000000006 RDI:
0000000000000000
[ 84.979628] RBP:
ffffc900005a7dd0 R08:
0000000000000000 R09:
0000000000000000
[ 84.980501] R10:
0000000000000001 R11:
0000000000000008 R12:
0000000000000001
[ 84.981373] R13:
ffffffffffffffea R14:
ffffffff81a9b4c0 R15:
0000000000000002
[ 84.982249] FS:
00007feb237b7700(0000) GS:
ffff88003fc00000(0000) knlGS:
0000000000000000
[ 84.983231] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 84.983941] CR2:
ffffffff81684b10 CR3:
0000000038492000 CR4:
00000000000406f0
[ 84.984817] Call Trace:
[ 84.985133] proc_tcp_early_demux+0x29/0x30
I think this is the second time such a patch has been reverted.
Cc: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bhumika Goyal [Fri, 25 Aug 2017 14:21:45 +0000 (19:51 +0530)]
RDS: make rhashtable_params const
Make this const as it is either used during a copy operation or passed
to a const argument of the function rhltable_init
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bhumika Goyal [Fri, 25 Aug 2017 14:21:44 +0000 (19:51 +0530)]
ipv4: make net_protocol const
Make these const as they are only passed to a const argument of the
function inet_add_protocol.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bhumika Goyal [Fri, 25 Aug 2017 14:21:42 +0000 (19:51 +0530)]
bridge: make ebt_table const
Make this const as it is only passed to a const argument of the function
ebt_register_table.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Aug 2017 18:13:22 +0000 (11:13 -0700)]
Merge branch 'sockmap-uapi-updates-and-fixes'
John Fastabend says:
====================
sockmap UAPI updates and fixes
This series updates sockmap UAPI, adds additional test cases and
provides a couple fixes.
First the UAPI changes. The original API added two sockmap specific
API artifacts (a) a new map_flags field with a sockmap specific update
command and (b) a new sockmap specific attach field in the attach data
structure. After this series instead of attaching programs with a
single command now two commands are used to attach programs to maps
individually. This allows us to add new programs easily in the future
and avoids any specific sockmap data structure additions. The
map_flags field is also removed and instead we allow socks to be
added to multiple maps that may or may not have programs attached.
This allows users to decide if a sock should run a SK_SKB program type
on receive based on the map it is attached to. This is a nice
improvement. See patches for specific details.
More test cases were added to test above changes and also stress test
the interface.
Finally two fixes/improvements were made. First a missing rcu
section was added. Second now sockmap can build without KCM being
used to trigger 'y' on CONFIG_STREAM_PARSER by selecting a new
BPF config option.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Mon, 28 Aug 2017 14:12:41 +0000 (07:12 -0700)]
bpf: test_maps add sockmap stress test
Sockmap is a bit different than normal stress tests that can run
in parallel as is. We need to reuse the same socket pool and map
pool to get good stress test cases.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Mon, 28 Aug 2017 14:12:21 +0000 (07:12 -0700)]
bpf: sockmap requires STREAM_PARSER add Kconfig entry
SOCKMAP uses strparser code (compiled with Kconfig option
CONFIG_STREAM_PARSER) to run the parser BPF program. Without this
config option set sockmap wont be compiled. However, at the moment
the only way to pull in the strparser code is to enable KCM.
To resolve this create a BPF specific config option to pull
only the strparser piece in that sockmap needs. This also
allows folks who want to use BPF/syscall/maps but don't need
sockmap to easily opt out.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Mon, 28 Aug 2017 14:12:01 +0000 (07:12 -0700)]
bpf: sockmap indicate sock events to listeners
After userspace pushes sockets into a sockmap it may not be receiving
data (assuming stream_{parser|verdict} programs are attached). But, it
may still want to manage the socks. A common pattern is to poll/select
for a POLLRDHUP event so we can close the sock.
This patch adds the logic to wake up these listeners.
Also add TCP_SYN_SENT to the list of events to handle. We don't want
to break the connection just because we happen to be in this state.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Mon, 28 Aug 2017 14:11:43 +0000 (07:11 -0700)]
bpf: harden sockmap program attach to ensure correct map type
When attaching a program to sockmap we need to check map type
is correct.
Fixes:
174a79ff9515 ("bpf: sockmap with sk redirect support")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Mon, 28 Aug 2017 14:11:24 +0000 (07:11 -0700)]
bpf: more SK_SKB selftests
Tests packet read/writes and additional skb fields.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Mon, 28 Aug 2017 14:11:05 +0000 (07:11 -0700)]
bpf: additional sockmap self tests
Add some more sockmap tests to cover,
- forwarding to NULL entries
- more than two maps to test list ops
- forwarding to different map
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>