OSDN Git Service
Arend van Spriel [Wed, 10 Jun 2015 22:12:19 +0000 (00:12 +0200)]
brcmfmac: rework .get_station() callback
The .get_station() cfg80211 callback is used in several scenarios. In
managed mode it can obtain information about the access-point and its
BSS parameters. In managed mode it can also obtain information about
TDLS peers. In AP mode it can obtain information about connected
clients.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pontus Fuchs [Wed, 10 Jun 2015 22:12:18 +0000 (00:12 +0200)]
brcmfmac: Build wiphy mode and interface combinations dynamically
Switch from using semi hard coded interface combinations. This makes
it easier to announce what the firmware actually supports. This fixes
the case where brcmfmac announces p2p but the firmware doesn't
support it.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Pontus Fuchs <pontusf@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pontus Fuchs [Wed, 10 Jun 2015 22:12:17 +0000 (00:12 +0200)]
brcmfmac: Check if firmware supports p2p
Add a feature flag to reflect the firmware's p2p capability.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Pontus Fuchs <pontusf@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jakub Kicinski [Wed, 10 Jun 2015 18:10:09 +0000 (20:10 +0200)]
mt7601u: don't warn about devices without per-rate power table
We expect EEPROM per-rate power table to be filled with
s6 values and warn user if values are invalid. However,
there appear to be devices which don't have this section
of EEPROM initialized. In such case we should ignore
the values and leave the driver power tables set to zero.
Note that vendor driver doesn't care about this case but
mt76x2 skips 0xff per value. We take mt76x2's approach.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Stanislaw Gruszka [Wed, 10 Jun 2015 14:30:05 +0000 (16:30 +0200)]
MAINTAINERS: remove rt2x00.serialmonkey.com list and web page
rt2x00.serialmonkey.com will be shutdown.
Since traffic on rt2x00 mailing list is very low, we can use only
linux-wireless list for any rt2x00 related topics.
Thanks for Luis Correia, Ivo van Doorn and Mark Wallis for maintaining
rt2x00 servers for years!
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Chunfan Chen [Wed, 10 Jun 2015 13:19:48 +0000 (06:19 -0700)]
mwifiex: handle BT coex event to adjust Rx BA window size
If timeshare coexistance between bluetooth and WLAN gets enabled,
firmware will give host an event to reduce Rx AMPDU BA window size.
The event is handled in this patch.
Signed-off-by: Chunfan Chen <jeffc@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Chun-Yeow Yeoh [Tue, 9 Jun 2015 07:59:49 +0000 (15:59 +0800)]
ath9k_htc: add support of channel switch
Add the support of channel switching functionality, similar
to ath9k support.
Tested with TP-Link TL-WN722N and TL-WN821N.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend van Spriel [Mon, 8 Jun 2015 12:38:35 +0000 (14:38 +0200)]
brcmfmac: use debugfs_create_devm_seqfile() helper function
Some time ago the function debugfs_create_devm_seqfile() was
introduced in debugfs. The caller simply needs to provide a
device pointer and read function. The function brcmf_debugfs_add_entry()
is now simply a wrapper only doing the work for CONFIG_BRCMDBG.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend van Spriel [Mon, 8 Jun 2015 12:38:34 +0000 (14:38 +0200)]
brcmfmac: remove watchdog reset from brcmf_pcie_buscoreprep()
The watchdog reset as done in brcmf_pcie_buscoreprep() is not
sufficient. It needs to modify PCIe core registers as well
which is properly done by brcmf_pcie_reset_device() after the
chip recognition is done. So the faulty watchdog reset can be
removed as it was causing driver reload to fail and hang the
system requiring a power-cycle. Instead the call to to the
brcmf_pcie_reset_device() function is done twice in the unload.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend van Spriel [Mon, 8 Jun 2015 12:38:33 +0000 (14:38 +0200)]
brcmfmac: remove chipinfo debugfs entry
The information provided by chipinfo is also provided by the
revinfo debugfs entry. Removing it from debugfs.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hante Meuleman [Mon, 8 Jun 2015 12:38:32 +0000 (14:38 +0200)]
brcmfmac: Update msgbuf read pointer quicker.
On device to host data using msgbuf the read pointer gets updated
once all data is processed. Updating this pointer more frequently
allows the firmware to add more data quicker. This will result in
slightly higher and more stable throughput on CPU bounded host
processors.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Taehee Yoo [Sun, 7 Jun 2015 13:33:36 +0000 (22:33 +0900)]
rtlwifi: rtl8192c: Add init codes for "fw_version" and "fw_subversion".
The variable "fw_version" is used in the _ResetDigitalProcedure1().
but It is not initialized. so I add init codes for "fw_version" and
"fw_subversion".
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Taehee Yoo [Sun, 7 Jun 2015 12:03:57 +0000 (21:03 +0900)]
rtlwifi: rtl8192cu: Fix variable isfirst_ampdu
rtl92cu_rx_query_desc set a isampdu twice.
but second code is related to isfirst_ampdu.
so i change it.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Taehee Yoo [Sun, 7 Jun 2015 12:03:56 +0000 (21:03 +0900)]
rtlwifi: rtl8192cu: debug message change "RTL8192CE" to "RTL8192CU"
In the rtlwifi/rtl8192cu, I change debug message "RTL8192CE" to
"RTL8192CU".
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Taehee Yoo [Sat, 6 Jun 2015 10:57:14 +0000 (19:57 +0900)]
rtlwifi: rtl8192cu: remove duplicated routine in _rtl92c_phy_rf6052_config_parafile
in the _rtl92c_phy_rf6052_config_parafile(), cases
RF90_PATH_A and RF90_PATH_B call the same routine.
so i remove one of these routine. also the return
routine is duplicated. so i remove it.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hans Ulli Kroll [Sun, 7 Jun 2015 11:19:16 +0000 (13:19 +0200)]
rtlwifi: fix tm_trigger usage
While working on getting my rtl8821au driver in pretty shape for
inclusion, it is dicosvered that the tm_trigger flag is used only for
the first device using this driver.
This flag handles the thermal power management in the hardware.
To change this add a entry in sttruct rtl_dm, so each device can handle
is separately.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Taehee Yoo [Thu, 4 Jun 2015 09:11:33 +0000 (18:11 +0900)]
rtlwifi: rtl8192cu: remove INTF_PCI and INTF_USB
in the rtlwifi/rtl8192cu, INTF_PCI and INTF_USB is unnecessary.
because RTL8192CU chipset is only USB interface.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Taehee Yoo [Thu, 4 Jun 2015 08:43:36 +0000 (17:43 +0900)]
rtlwifi: rtl8192cu: remove _InitBeaconParameters().
_InitBeaconParameters() and rtl92cu_init_beacon_parameters() is
same routine. I remove both functions. then i add
_rtl92cu_init_beacon_parameters() in the hw.c.
_rtl92cu_init_beacon_parameters() is same routine with
_InitBeaconParameters().
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Taehee Yoo [Thu, 4 Jun 2015 08:43:34 +0000 (17:43 +0900)]
rtlwifi: rtl8192cu: remove IS_HARDWARE_TYPE_8192CE and IS_HARDWARE_TYPE_8192CU
in the rtlwifi/rtl8192cu, IS_HARDWARE_TYPE_8192CE and IS_HARDWARE_TYPE_8192CU
is unnecessary. because rtlwifi/rtl8192cu codes aren't shared.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Sun, 7 Jun 2015 11:15:31 +0000 (13:15 +0200)]
bcma: lower dependency of BCMA_DRIVER_PCI_HOSTMODE
This extension of BCMA_DRIVER_PCI has no reason to depend on
BCMA_HOST_PCI. User may just want to have PCI device attached to SoC
registered without enabling any extra client mode code.
This can be useful when having non-bcma PCI device attached or when
using other PCI driver.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Sun, 7 Jun 2015 11:15:30 +0000 (13:15 +0200)]
bcma: make calls to PCI hostmode functions config-safe
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Sat, 6 Jun 2015 20:45:59 +0000 (22:45 +0200)]
b43: fix support for 14e4:4321 PCI dev with BCM4321 chipset
It seems Broadcom released two devices with conflicting device id. There
are for sure 14e4:4321 PCI devices with BCM4321 (N-PHY) chipset, they
can be found in routers, e.g. Netgear WNR834Bv2. However, according to
Broadcom public sources 0x4321 is also used for 5 GHz BCM4306 (G-PHY).
It's unsure if they meant PCI device id, or "virtual" id (from SPROM).
To distinguish these devices lets check PHY type (G vs. N).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Thu, 4 Jun 2015 20:11:07 +0000 (22:11 +0200)]
brcmfmac: use direct data pointer in NVRAM parser struct
As we plan to add support for platform NVRAM we should store direct
data pointer without the extra struct firmware layer. This will allow
us to support other sources with the only requirement being u8 buffer.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jakub Kicinski [Tue, 2 Jun 2015 19:11:28 +0000 (21:11 +0200)]
mt7601u: set promiscous mode based on FIF_OTHER_BSS
Most drivers use FIF_OTHER_BSS to set promiscous mode. Let us
follow their lead even though it doesn't match exactly the HW
filter flags.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jakub Kicinski [Tue, 2 Jun 2015 19:11:27 +0000 (21:11 +0200)]
mt7601u: don't cleanup device second time after .resume()
Make sure .disconnect() doesn't cleanup the device if
.resume() failed. This may happen when device is removed
during suspend.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jakub Kicinski [Tue, 2 Jun 2015 19:11:26 +0000 (21:11 +0200)]
mt7601u: watch out for invalid-length frames
Users of older Ralink devices report that received frames
sometimes have zero length. Watch out for that.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jakub Kicinski [Tue, 2 Jun 2015 19:11:25 +0000 (21:11 +0200)]
mt7601u: unify paged and non-paged RX dma paths
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Sun, 31 May 2015 00:52:26 +0000 (02:52 +0200)]
brcmfmac: set wiphy perm_addr to hardware MAC address
This allows e.g. user space to use /sys/class/ieee80211/*/macaddress
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Thu, 28 May 2015 12:19:21 +0000 (14:19 +0200)]
brcmfmac: support NVRAMs containing pci devpaths (instead of pcie)
Recently Broadcom added support for NVRAMs with entries for multiple
PCIe devices. One of the supported formats is based on prefixes defined
like: devpath0=pcie/1/4/ and entries like 0:foo=bar 0:baz=qux etc.
Unfortunately there are also a bit older devices using different way of
defining prefixes, e.g. SmartRG SR400ac (2 x BCM43602) with entries:
devpath0=pci/1/1/
devpath1=pci/2/1
Broadcom stated this old format will never be used/supported by brcmfmac
but given the simplicity of this patch I'll insist on supporting it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Thu, 4 Jun 2015 19:31:54 +0000 (01:01 +0530)]
mwifiex: update current config_band info in start_ap
It was observed that AP beacons would not reflect correct regulatory
information upon starting AP in A band. This was because of missing
AP config band update in set_channel of start_ap.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Zhaoyang Liu [Thu, 4 Jun 2015 19:31:53 +0000 (01:01 +0530)]
mwifiex: change debug dump issue since skb maybe null
This patch fixes semantic warning for debugging data dump feature.
Previous code is based on the assumption that skb is not null.
New change makes sure that we already have data buffer.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Taehee Yoo [Thu, 4 Jun 2015 00:47:42 +0000 (09:47 +0900)]
rtlwifi: rtl8192cu: Fix performance issue.
After physical reconnect, the rtl8192cu chipset shows low
transmission rates.It cause is that variable "iqk_initialized"
do not de-initialized. So I add this code.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Wed, 3 Jun 2015 11:29:47 +0000 (16:59 +0530)]
mwifiex: do not decrease tx_pending for AMSDU packet once more
Negative adapter->tx_pending is observed while running data traffic,
because tx_pending is decreased once more for AMSDU packet.
since tx_pending have been decreased for all the source MSDU packets,
we don't need to update once more for AMSDU packet.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Wed, 3 Jun 2015 11:29:46 +0000 (16:59 +0530)]
mwifiex: using right tid for addressing ra_list
This patch fixes issue with the accessing correct ra_list by
downgrading corresponding tid number.
Alternatively, ra lists are created in mwifiex_wmm_add_buf_txqueue
using downgraded tid number.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Wed, 3 Jun 2015 11:29:45 +0000 (16:59 +0530)]
mwifiex: update AP WMM settings from BSS_START event
This was missing and would cause issue in WMM handling.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Wed, 3 Jun 2015 11:29:44 +0000 (16:59 +0530)]
mwifiex: advertise PS ON by default support to cfg80211
This would enable driver to enter powersave as soon as connected.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Wed, 3 Jun 2015 11:29:43 +0000 (16:59 +0530)]
mwifiex: drop block-ack action frames
We often see ADDBA request packets coming to driver because driver
has registered for action frame subtype. We dont process BA action
frames in host; drop such frames.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Xinmin Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Wed, 3 Jun 2015 11:29:42 +0000 (16:59 +0530)]
mwifiex: support downloading IEs from tail
Earlier only RSN, WPA and channel switch IEs from tail buffer would
be downloaded to FW.
This patch adds support for downloading more IEs from tail buffer.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Wed, 3 Jun 2015 11:29:41 +0000 (16:59 +0530)]
mwifiex: parse power constraint IE from Tail
This patch adds support to parse power constraint IEs from
Tail buffer. This power constraint is then set to FW during
bss_config download.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Wed, 3 Jun 2015 11:29:40 +0000 (16:59 +0530)]
mwifiex: dump station support in uap mode
This patch extend cfg80211 dump_station handler, support for
dump stations associated to mwifiex micro AP.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Wed, 3 Jun 2015 11:29:39 +0000 (16:59 +0530)]
mwifiex: add sta_list firmware command
This patch add sta_list firmware command, which can be used
to get power status and rssi for the stations associated to
mwifiex micro AP.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Wed, 3 Jun 2015 11:29:38 +0000 (16:59 +0530)]
mwifiex: maintain station statistic in uap mode
This patch maintain statistic information for the stations associated
to the mwifiex micro AP, include tx/rx bytes/packets, signal strength,
tx bitrate.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Wed, 3 Jun 2015 11:29:37 +0000 (16:59 +0530)]
mwifiex: add cfg80211 get_channel handler
This patch add cfg80211 get_channel handler for mwifiex.
The handler will be used to report current channel to upper
layer utility.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Wed, 3 Jun 2015 11:29:36 +0000 (16:59 +0530)]
mwifiex: disable CAC upon radar detection event
This patch adds support to disable ongoing CAC in FW upon
detecting radar during CAC period.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Wed, 3 Jun 2015 11:29:35 +0000 (16:59 +0530)]
mwifiex: reset 11h active flag when chandef does not require dfs
This patch fixes an issue where we were still setting 11h_active
flag to true for channel defs where DFS is not required.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Wed, 3 Jun 2015 11:29:34 +0000 (16:59 +0530)]
mwifiex: enable 11d after bss reset
BSS reset would reset all state information in FW.
Issue 11d config command after reset to enabled 11d in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Wed, 3 Jun 2015 11:29:33 +0000 (16:59 +0530)]
mwifiex: support AP reset after bss_stop
This would enable clearing of FW bss data structures when AP
operations are stopped.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Wed, 3 Jun 2015 11:29:32 +0000 (16:59 +0530)]
mwifiex: correct bss_type assignment
Correct bss_type assignment in add_virtual_interface.
This would ensure correct operation in multiple station scenarios.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Wed, 3 Jun 2015 11:29:31 +0000 (16:59 +0530)]
mwifiex: verbose logging for association failure messages
This patch adds more detailed information about association failures
- reason and states.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Felix Fietkau [Tue, 2 Jun 2015 08:38:32 +0000 (10:38 +0200)]
ath9k: fix DMA stop sequence for AR9003+
AR93xx and newer needs to stop rx before tx to avoid getting the DMA
engine or MAC into a stuck state.
This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Julia Lawall [Thu, 28 May 2015 21:02:20 +0000 (23:02 +0200)]
wl1251: drop unneeded goto
Delete jump to a label on the next line, when that label is not
used elsewhere.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier l;
@@
-if (...) goto l;
-l:
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wei Liu [Wed, 3 Jun 2015 10:10:42 +0000 (11:10 +0100)]
tcp: double default TSQ output bytes limit
Xen virtual network driver has higher latency than a physical NIC.
Having only 128K as limit for TSQ introduced 30% regression in guest
throughput.
This patch raises the limit to 256K. This reduces the regression to 8%.
This buys us more time to work out a proper solution in the long run.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 4 Jun 2015 06:49:21 +0000 (23:49 -0700)]
tcp: remove redundant checks
tcp_v4_rcv() checks the following before calling tcp_v4_do_rcv():
if (th->doff < sizeof(struct tcphdr) / 4)
goto bad_packet;
if (!pskb_may_pull(skb, th->doff * 4))
goto discard_it;
So following check in tcp_v4_do_rcv() is redundant
and "goto csum_err;" is wrong anyway.
if (skb->len < tcp_hdrlen(skb) || ...)
goto csum_err;
A second check can be removed after no_tcp_socket label for same reason.
Same tests can be removed in tcp_v6_do_rcv()
Note : short tcp frames are not properly accounted in tcpInErrs MIB,
because pskb_may_pull() failure simply drops incoming skb, we might
fix this in a separate patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Jun 2015 06:47:24 +0000 (23:47 -0700)]
Merge branch 'switchdev-next'
Scott Feldman says:
====================
switchdev: documentation updates
Update the switchdev documentation to clarify that for IPV4 FIB object, the add
op is used for both adding and modifying the FIB entry on the device.
I found a few other white-space and grammer issues to fix, and to clarify the
static FDB ops.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman [Thu, 4 Jun 2015 03:43:43 +0000 (20:43 -0700)]
switchdev: documentation: use switchdev_port_obj_xxx for IPv4 FIB add/modify/delete ops
Clarify in documentation and code that IPV4 FIB add operation is used for
both adding a new FIB entry to the device and for modifying an existing FIB
entry on the device.
Also, remove left-over references to ipv4_fib ops and replace with details
on SWITCHDEV_PORT_IPV4_FIB object.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman [Thu, 4 Jun 2015 03:43:42 +0000 (20:43 -0700)]
switchdev: documentation: for static FDB ops, use switchdev_port_fdb_xxx ops
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman [Thu, 4 Jun 2015 03:43:41 +0000 (20:43 -0700)]
switchdev: documentation: fix grammer error
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman [Thu, 4 Jun 2015 03:43:40 +0000 (20:43 -0700)]
switchdev: documentation: fix longer-than-80-char lines
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Jun 2015 06:44:57 +0000 (23:44 -0700)]
Merge tag 'wireless-drivers-next-for-davem-2015-06-03' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
new driver mt7601u for MediaTek Wi-Fi devices MT7601U
ath10k:
* qca6174 power consumption improvements, enable ASPM etc (Michal)
wil6210:
* support Wi-Fi Simple Configuration in STA mode
iwlwifi:
* a few fixes (re-enablement of interrupts for certain new
platforms that have special power states)
* Rework completely the RBD allocation model towards new
multi RX hardware.
* cleanups
* scan reworks continuation (Luca)
mwifiex:
* improve firmware debug functionality
rtlwifi:
* update regulatory database
brcmfmac:
* cleanup and new feature support in PCIe code
* alternative nvram loading for router support
====================
Conflicts:
drivers/net/wireless/iwlwifi/Kconfig
Trivial conflict in iwlwifi Kconfig, two commits adding
the same two chip numbers to the help text, but order
transposed.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Jun 2015 06:40:20 +0000 (23:40 -0700)]
Merge branch 'cxgb4-next'
Hariprasad Shenai says:
====================
cxgb4: Adds support for various ethtool stats
This patch series adds the following:
Adds support to dump adapter specific stats in ethtool
Adds support to dump channel stats in ethtool
Adds support to dump loopback port stats in ethtool
Remove wake-on-lan get/set ethtool support
This patch series has been created against net-next tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Wed, 3 Jun 2015 15:34:42 +0000 (21:04 +0530)]
cxgb4: Remove WOL get/set ethtool support
Remove ethtool get/set support for wake on lan, adapter doesn't support
it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Wed, 3 Jun 2015 15:34:41 +0000 (21:04 +0530)]
cxgb4: Add support to dump loopback port stats
Add support in ethtool to dump loopback port statistics
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Wed, 3 Jun 2015 15:34:40 +0000 (21:04 +0530)]
cxgb4: Add support in ethtool to dump channel stats
Add support in ethtool to dump adapter channel stats
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Wed, 3 Jun 2015 15:34:39 +0000 (21:04 +0530)]
cxgb4: Add ethtool support to get adapter stats
Add ethtool support to get adapter specific hardware statistics
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Jun 2015 03:22:46 +0000 (20:22 -0700)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
pull request: batman-adv
20150603
here you have our second batch of patches intended for net-next.
In this patchset you won't find any new features, but quite some code
cleanup work, a bunch of code style fixes and also comments corrections
by Markus Pargmann.
Moreover you have a patch from Sven Eckelmann removing an unnecessary
NULL check in batadv_iv_ogm_update_seqnos().
Please pull or let me know of any problem!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rasmus Villemoes [Wed, 3 Jun 2015 11:44:03 +0000 (13:44 +0200)]
net: tulip: rearrange order of searching for substrings
Currently, two of the branches are dead code, since an earlier smaller
substring would have been found ("TP" in the "TP_NW" case and either
of "BNC" and "AUI" in the "BNC_AUI" case). Rearrange the strstr()
calls so that the longer strings are searched for first.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Jun 2015 03:19:16 +0000 (20:19 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-06-03
This series contains updates to e1000e only.
Yanir provides 8 fixes and 1 version bump for e1000e. First fix resolves
a possible unit hang if multiple descriptors are available in the rings
during reset or runtime suspend. Fixed a warning on SPARC compile based
on a suggested solution from Alex Duyck. Fixed a logical error, where
a "if" condition under which a flush should occur, was revered. Fixed
a hardware issue that prevented i219 from working in legacy interrupts
mode. Fixed the hardware clock configuration and suprious non-linear
increment. Lastly, fixed a system hang which occurred during execution
of "ethtool -t <NIC>", by disabling MULR for the loopback test to avoid
the hand state.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov [Tue, 2 Jun 2015 23:03:14 +0000 (16:03 -0700)]
bpf: introduce bpf_clone_redirect() helper
Allow eBPF programs attached to classifier/actions to call
bpf_clone_redirect(skb, ifindex, flags) helper which will
mirror or redirect the packet by dynamic ifindex selection
from within the program to a target device either at ingress
or at egress. Can be used for various scenarios, for example,
to load balance skbs into veths, split parts of the traffic
to local taps, etc.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carol Soto [Tue, 2 Jun 2015 21:07:25 +0000 (16:07 -0500)]
net/mlx4_core: fix typo in mlx4_set_vf_mac
fix typo in mlx4_set_vf_mac
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carol Soto [Tue, 2 Jun 2015 21:07:24 +0000 (16:07 -0500)]
net/mlx4_core: need to call close fw if alloc icm is called twice
If mlx4_enable_sriov is called by adapter without this
feature MLX4_DEV_CAP_FLAG2_SYS_EQS then during this path the function alloc
icm is called twice without freeing the structures from the first time.
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carol L Soto [Tue, 2 Jun 2015 21:07:23 +0000 (16:07 -0500)]
net/mlx4_core: double free of dev_vfs
If user loads mlx4_core with num_vfs greater than
supported then variable dev->dev_vfs is freed 2 times after unloading the
driver.
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Malcolm [Tue, 2 Jun 2015 19:31:17 +0000 (15:31 -0400)]
drivers/net/ethernet/dec/tulip/uli526x.c: fix misleading indentation in uli526x_timer
This code in drivers/net/ethernet/dec/tulip/uli526x.c
function "uli526x_timer":
1086 } else
1087 if ((tmp_cr12 & 0x3) && db->link_failed) {
[...snip...]
1109 }
1110 else if(!(tmp_cr12 & 0x3) && db->link_failed)
1111 {
[...snip...]
1117 }
1118 db->init=0;
is misleadingly indented: the
db->init=0
is indented as if part of the else clause at line 1086, but it is
independent of it (no braces before the "if" at line 1087).
This patch fixes the indentation to reflect the actual meaning of the code,
though is it actually meant to be part of the "else" clause? (I'm a
compiler developer, not a kernel person). It also adds spaces around
the assignment, to placate checkpatch.pl.
Seen via an experimental new gcc warning I'm working on for gcc 6,
-Wmisleading-indentation, using gcc r223098 adding
-Werror=misleading-indentation to KBUILD_CFLAGS in Makefile.
The experimental GCC emits this warning (as an error), rightly IMHO:
drivers/net/ethernet/dec/tulip/uli526x.c: In function ‘uli526x_timer’:
drivers/net/ethernet/dec/tulip/uli526x.c:1118:3: error: statement is
indented as if it were guarded by... [-Werror=misleading-indentation]
db->init=0;
^
drivers/net/ethernet/dec/tulip/uli526x.c:1086:4: note: ...this ‘else’
clause, but it is not
} else
^
Hope this is helpful
Dave
Signed-off-by: David Malcolm <dmalcolm@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Murphy [Tue, 2 Jun 2015 14:34:37 +0000 (09:34 -0500)]
net: phy: dp83867: Add TI dp83867 phy
Add support for the TI dp83867 Gigabit ethernet phy
device.
The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antonio Murdaca [Tue, 2 Jun 2015 12:35:52 +0000 (14:35 +0200)]
ethernet: micrel: use time_after_eq
use the time_after_eq macro for jiffies comparison operation
Signed-off-by: Antonio Murdaca <antonio.murdaca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Tue, 2 Jun 2015 07:29:48 +0000 (10:29 +0300)]
net/mlx4_core: Fix build failure introduced by the EQ pool changes
When CONFIG_RFS_ACCEL or SMP aren't set, we fail to build, fix it.
Also, avoid build warning as of unused function on that setup.
Fixes:
c66fa19c405a ('net/mlx4: Add EQ pool')
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Pargmann [Fri, 26 Dec 2014 11:41:41 +0000 (12:41 +0100)]
batman-adv: Remove unnecessary ret variable in algo_register
Remove ret variable and all jumps.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Markus Pargmann [Fri, 26 Dec 2014 11:41:40 +0000 (12:41 +0100)]
batman-adv: Remove unnecessary ret variable
We can avoid this indirect return variable by directly returning the
error values.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Markus Pargmann [Fri, 26 Dec 2014 11:41:39 +0000 (12:41 +0100)]
batman-adv: main, batadv_compare_eth return bool
Declare the returntype of batadv_compare_eth as bool.
The function called inside this helper function
(ether_addr_equal_unaligned) also uses bool as return value, so there is
no need to return int.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Markus Pargmann [Fri, 26 Dec 2014 11:41:38 +0000 (12:41 +0100)]
batman-adv: main, Convert is_my_mac() to bool
It is much clearer to see a bool type as return value than 'int' for
functions that are supposed to return true or false.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Sven Eckelmann [Sun, 1 Mar 2015 15:56:26 +0000 (16:56 +0100)]
batman-adv: Remove unnecessary check for orig_ifinfo not NULL
orig_ifinfo is dereferenced multiple times in batadv_iv_ogm_update_seqnos
before the check for NULL is done. The function also exists at the
beginning when orig_ifinfo would have been NULL. This makes the check at
the end unnecessary and only confuses the reader/code analyzers.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Markus Pargmann [Fri, 26 Dec 2014 11:41:37 +0000 (12:41 +0100)]
batman-adv: types, Fix comment on bcast_own
batadv_orig_bat_iv->bcast_own is actually not a bitfield, it is an
array. Adjust the comment accordingly.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Yanir Lubetkin [Tue, 2 Jun 2015 14:05:50 +0000 (17:05 +0300)]
e1000e: Bump the version to 3.2.5
Bump the version to reflect the driver changes and bug fixes for i219.
Also update the copyright, while we are at it.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Yanir Lubetkin [Tue, 2 Jun 2015 14:05:47 +0000 (17:05 +0300)]
e1000e: fix unit hang during loopback test
System would hang during execution of "ethtool -t <NIC>" for the same
reason that required flushing the descriptor rings. This fix disables
MULR for the loopback test to avoid the hang state.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Yanir Lubetkin [Tue, 2 Jun 2015 14:05:45 +0000 (17:05 +0300)]
e1000e: fix systim issues
Two issues involving systim were reported.
1. Clock is not running in the correct frequency
2. In some situations, systim values were not incremented linearly
This patch fixes the hardware clock configuration and the spurious
non-linear increment.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Yanir Lubetkin [Tue, 2 Jun 2015 14:05:42 +0000 (17:05 +0300)]
e1000e: fix legacy interrupt handling in i219
This fix handles a hardware issue that prevented i219 from
working in legacy interrupts mode (IntMode=0)
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Yanir Lubetkin [Tue, 2 Jun 2015 14:05:38 +0000 (17:05 +0300)]
e1000e: fix flush_desc_ring implementation
The indication that a descriptor ring flush is required was read from
FEXTNVM7 by mistake. It should be read from the PCI config space.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Yanir Lubetkin [Wed, 22 Apr 2015 16:25:17 +0000 (19:25 +0300)]
e1000e: fix logical error in flush_desc_rings
The condition under which the flush should occur was reversed. The fix
should be applied before any HW reset (unless followed by bus reset)
and before any power state transition from D0.
If E1000_FEXTNVM7_NEED_DESCRING_FLUSH bit is set in FEXTNVM7 and TDLEN > 0
the Tx ring should be flushed. (fixes ~95% of the hang states).
If the E1000_FEXTNVM7_NEED_DESCRING_FLUSH did not clear, we should also
flush the RX ring. Bug was caught by Alexander Duyck during a code review
when examining this fix.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Yanir Lubetkin [Wed, 22 Apr 2015 02:55:43 +0000 (05:55 +0300)]
e1000e: remove call to do_div and sign mismatch warning
Fixes a warning that was reported by Yanjiang Jin
<yanjiang.jin@windriver.com> by implementing the solution suggested by
Alexander Duyck <alexander.h.duyck@redhat.com>.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Yanir Lubetkin [Wed, 22 Apr 2015 01:15:01 +0000 (04:15 +0300)]
e1000e: i219 execute unit hang fix on every reset or power state transition
After testing various cases, the conclusion is that the fix MUST be
executed BEFORE any event that the HW is reset or transition to D3.
To fix that I moved the execution to the relevant places but per
Alexander Duyck's review, ensure now that the DMA is valid and was not
freed before manipulating the ring.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Yanir Lubetkin [Mon, 13 Apr 2015 23:20:21 +0000 (02:20 +0300)]
e1000e: i219 fix unit hang on reset and runtime D3
Unit hang may occur if multiple descriptors are available in the rings
during reset or runtime suspend. This state can be detected by testing
bit 8 in the FEXTNVM7 register. If this bit is set and there are pending
descriptors in one of the rings, we must flush them prior to reset. Same
applies entering runtime suspend.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kalle Valo [Wed, 3 Jun 2015 09:15:51 +0000 (12:15 +0300)]
Merge tag 'iwlwifi-next-for-kalle-2015-06-03' of https://git./linux/kernel/git/iwlwifi/iwlwifi-next
* a few fixes (re-enablement of interrupts for certain new
platforms that have special power states)
* Rework completely the RBD allocation model towards new
multi RX hardware.
* cleanups
* scan reworks continuation (Luca)
Markus Pargmann [Fri, 26 Dec 2014 11:41:36 +0000 (12:41 +0100)]
batman-adv: iv_ogm, fix comment function name
This is a small copy paste fix for batadv_ing_buffer_avg.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Markus Pargmann [Fri, 26 Dec 2014 11:41:35 +0000 (12:41 +0100)]
batman-adv: iv_ogm, fix coding style
The kernel coding style says, that there should not be multiple
assignments in one row.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Markus Pargmann [Fri, 26 Dec 2014 11:41:34 +0000 (12:41 +0100)]
batman-adv: iv_ogm, Fix dup_status comment
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Markus Pargmann [Fri, 26 Dec 2014 11:41:33 +0000 (12:41 +0100)]
batman-adv: iv_ogm_orig_update, style, add missing brackets
CodingStyle describes that either none or both branches of a conditional
have to have brackets.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Markus Pargmann [Fri, 26 Dec 2014 11:41:32 +0000 (12:41 +0100)]
batman-adv: iv_ogm_queue_add, Simplify expressions
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Markus Pargmann [Fri, 26 Dec 2014 11:41:31 +0000 (12:41 +0100)]
batman-adv: iv_ogm_aggregate_new, simplify error handling
It is just a bit easier to put the error handling at one place and let
multiple error paths use the same calls.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Johannes Berg [Wed, 20 May 2015 14:51:28 +0000 (16:51 +0200)]
iwlwifi: mvm: advertise only HW-supported ciphers
After the new ciphers CCMP-256 and GCMP-128/256 were implemented,
wpa_supplicant could start negotiating them and use the software
implementation. This, however, breaks D3 behaviour in the driver
since it means that WoWLAN will not be possible.
To avoid breaking that feature, advertise only ciphers that the
hardware supports.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Emmanuel Grumbach [Wed, 3 Jun 2015 06:54:18 +0000 (09:54 +0300)]
iwlwifi: bump the iwlmvm API number to 15
The driver is now ready to handle the -15.ucode.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Matti Gottlieb [Sun, 31 May 2015 06:18:30 +0000 (09:18 +0300)]
iwlwifi: mvm: Add DC2DC_CONFIG_CMD (0x83) cmd & TLV
Add DC2DC_CONFIG_CMD (0x83) cmd.
Add IWL_UCODE_TLV_CAPA_DC2DC_CONFIG_SUPPORT tlv.
The command allows the driver get & set the DCDC's frequency tune.
(freq_tune is the divider that is used to calculate the actual DCDC's
clock rate)
The command always returns the current/updated frequency tune values of
the DCDC.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>