OSDN Git Service
Wey-Yi Guy [Thu, 17 Sep 2009 17:43:46 +0000 (10:43 -0700)]
iwlwifi: EEPROM version for 1000 and 6000 series
Update EEPROM version requirement for 1000 and 6000 series of NIC
for EEPROM version verification.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 17 Sep 2009 17:43:45 +0000 (10:43 -0700)]
iwlwifi: allow user change protection mechanism for HT
Allow user to change protection mechanism for HT between RTS/CTS and
CTS-to-self through sysfs:
Show current protection mechanism for HT
cat /sys/class/net/wlan0/device/rts_ht_protection
Change protection mechanism for HT (only allowed while not-associated)
CTS-to-self:
echo 0 > /sys/class/net/wlan0/device/rts_ht_protection
RTS/CTS:
echo 1 > /sys/class/net/wlan0/device/rts_ht_protection
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 17 Sep 2009 17:43:44 +0000 (10:43 -0700)]
iwlwifi: Use RTS/CTS as the preferred protection mechanism for 6000 series
When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.
The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.
When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.
By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.
For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 11 Sep 2009 17:38:17 +0000 (10:38 -0700)]
iwlwifi: clarify and clean up chain settings
The chain settings we currently use in iwlwifi are
rather confusing -- and we also go by the wrong
settings entirely under certain circumstances. To
clean it up, create a new variable in the current
HT config -- single_chain_sufficient -- that tells
us whether we need more than one chain. Calculate
that based on the AP and operating mode (no IBSS
HT implemented -- so no need for multiple chains,
for station mode we use the AP's capabilities).
Additionally, since APs always send disabled SM PS
mode, keeping track of their sm_ps mode isn't very
useful -- doubly not so for our _own_ RX config
since that should depend on our, not the AP's, SM
PS mode.
Finally, document that our configuration of the
number of RX chains used is currently wrong when
in powersave (by adding a comment).
All together this removes the two remaining items
in struct iwl_ht_config that were done wrong there.
For the future, the number of RX chains and some
SM PS handshaking needs to be added to mac80211,
which then needs to tell us, and the new variable
current_ht_config.single_chain_sufficient should
also be calculated by mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 11 Sep 2009 17:38:16 +0000 (10:38 -0700)]
iwlwifi: show NVM version in debugfs
Show version number along with dumping NVM data, the version information
being removed from sysfs, add it back to debugfs to help debugging.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 11 Sep 2009 17:38:15 +0000 (10:38 -0700)]
iwlwifi: clean up ht config naming
Daniel Halperin pointed out that the naming
here is rather inconsistent with at least 3
different names being used for one thing in
different contexts. Rename the struct to
iwl_ht_config (rather than iwl_ht_info) and
use ht_conf as a variable for it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 11 Sep 2009 17:38:14 +0000 (10:38 -0700)]
iwlwifi: Adjust blink rate to compensate Clock difference
Adjust led blink rate to compensate on a MAC Clock difference on every
HW. Led blink rate analysis showed an average deviation of 0% on 3945,
5% on 4965 HW and 20% on 5000 series and up.
Need to compensate on the led on/off time per HW according to the
deviation to achieve the desired led frequency
The calculation is: (100-averageDeviation)/100 * blinkTime
For code efficiency the calculation will be:
compensation = (100 - averageDeviation) * 64 / 100
NewBlinkTime = (compensation * BlinkTime) / 64
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 11 Sep 2009 17:38:13 +0000 (10:38 -0700)]
iwlwifi: clean up ht config a little
is_ht can be bool instead of u8, and there's
no need to use IWL_CHANNEL_WIDTH_* constants
in supported_chan_width when that could just
be named is_40mhz instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 11 Sep 2009 17:38:11 +0000 (10:38 -0700)]
iwlwifi: separate set_hw_params function for 6000 series
Separate set_hw_params() function for 6000
series from 5000/1000 series because:
1) 6000 series use different set of sensitivity range table
2) 6000 series has different uCode image size
Also include the new sensitivity parameters needed by sensitivity
algorithm.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 11 Sep 2009 17:38:10 +0000 (10:38 -0700)]
iwlwifi: separate nic_config for different NIC
Different NIC has different requirements for configuration. Currently all
5000 series hardware and later share the same configuration function even
though they do not need the same configurations. Fix this by separating the
needed configuration actions for each hardware model.
.5000 series: L1-ASPM H/W bug work-around
configure radio
write CSR_HW_IF_CONFIG_REG for uCode use
work-around for NIC get stuck after early PCIe power off
.1000 series: write CSR_HW_IF_CONFIG_REG for uCode use
setting digital SVR for 1000 card to 1.32V
.6000 series: configure radio
write CSR_HW_IF_CONFIG_REG for uCode use
write CSR_GP_DRIVER_REG to indicate radio sku
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 11 Sep 2009 17:38:09 +0000 (10:38 -0700)]
iwlwifi: remove un-supported eeprom parameters
Remove few of the parameters not used and no longer valid in EEPROM.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 11 Sep 2009 17:38:07 +0000 (10:38 -0700)]
iwlwifi: modify LED blink index table
Modify LED blink index table to include 1Mbps.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 14 Sep 2009 09:09:38 +0000 (02:09 -0700)]
ath9k: make ath9k_common_ops const
As noted by Jiri.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 14 Sep 2009 07:55:09 +0000 (00:55 -0700)]
atheros: move bus ops to ath_common
This is the last part to make ath9k hw code core driver agnostic.
I believe ath9k_htc can now use use the hw code unmodified.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 14 Sep 2009 06:55:05 +0000 (23:55 -0700)]
ath9k: move ATH9K_RSSI_BAD to hw.h
mac.c is now core driver independent.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 14 Sep 2009 06:39:31 +0000 (23:39 -0700)]
ath9k: clarify what hw code is and remove ath9k.h from a few files
hw code will be shared between ath9k and ath9k_htc.
Just a few more files are left to clean up, mark them as well.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 14 Sep 2009 06:28:00 +0000 (23:28 -0700)]
ath9k: remove driver ASSERT, just use BUG_ON()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 14 Sep 2009 06:11:13 +0000 (23:11 -0700)]
ath9k: move ATH_AMPDU_LIMIT_MAX to hw.h
This is used by hw code.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 14 Sep 2009 06:04:44 +0000 (23:04 -0700)]
ath9k: remove ath9k_ht_macmode
This is used just to determine how to program the MAC,
either for 20 MHz operation of 40 MHz so just use conf_is_ht40()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 14 Sep 2009 05:05:04 +0000 (22:05 -0700)]
ath9k: remove ath9k 25 MHz HT40 spacing stuff
This was for supporting 25 MHz spacing for HT40, this is not used
as we use 20 MHz spacing instead for HT40 as per 802.11n. The hardware
is capable of it though so we leave the phymode definition and EEPROM
parsing for it. If some experimenter wants to work on this stuff stuff
you can add an extension enabling bool on ath_common and perhaps some
debugfs knob to enable it. Keep in mind you'll also need to update the
phymode with the AR_PHY_FC_DYN2040_EXT_CH which has been left on the
driver.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 14 Sep 2009 04:07:07 +0000 (21:07 -0700)]
atheros: move tx/rx chainmask to ath_common
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Sun, 13 Sep 2009 09:42:02 +0000 (02:42 -0700)]
atheros: add common debug printing
ath9k uses this for now, ath9k_htc is expected to re-use this
as well. We lave ath5k as is, but it certainly can also be
converted later.
The ath9k module parameter and debugfs entry is kept.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Sun, 13 Sep 2009 09:08:34 +0000 (02:08 -0700)]
ath9k: separate core driver and hw timer code
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Sun, 13 Sep 2009 07:03:27 +0000 (00:03 -0700)]
atheros: add ieee80211_hw to ath_common
Make use of it on hw code in ath9k to avoid
using the ath9k ath_softc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Fri, 11 Sep 2009 00:52:45 +0000 (17:52 -0700)]
atheros: define shared bssidmask setting
Also make ath5k and ath9k use it, and share register definitions.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 23:55:11 +0000 (16:55 -0700)]
ath5k: define ath_common ops
Only common ath read/write ops go through the common ops.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Fri, 11 Sep 2009 01:04:47 +0000 (18:04 -0700)]
ath5k: allocate ath5k_hw prior to initializing hw
We can propagate better errors upon failed hw initialization,
and set up the ath_common structure for attach purposes. This
will become important once we start using the ath_common
for read/write ops.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 23:11:21 +0000 (16:11 -0700)]
atheros/ath9k: add common read/write ops and port ath9k to use it
In an effort to make hw code driver core agnostic read
and write operations are defined on the ath_common structure.
This patch adds that and makes ath9k use it. This allows
drivers like ath9k_htc to define its own read/write ops and
still rely on the same hw code. This also paves the way for
sharing code between ath9k/ath5k/ath9k_htc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 19:12:23 +0000 (12:12 -0700)]
ath9k: Define bus agnostic bluetooth coex prep helper
We disable ASPM when enabling bluetooth coexistance. Disabling
ASPM is a bus specific operation. In the future other buses may
support bluetooth coexistance, an example is USB. To this end
move the current routine which disables ASPM into pci.c, and declare
it the PCI bt_coex_prep() helper. Additionally, since ASPM is
a PCI-Express primitive ensure we don't ever try to muck with ASPM
registers on non PCI-express devices.
This also cleans up hw.c to not include bus specific headers or
utilities.
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Zhifeng Cai <zhifeng.cai@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 18:20:57 +0000 (11:20 -0700)]
ath5k: move ath_common to ath5k_hw
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 18:08:14 +0000 (11:08 -0700)]
ath9k: move ath_common to ath_hw
This ensures that we can access common on hw related code
independent of the driver core.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 17:57:00 +0000 (10:57 -0700)]
ath5k: initialize eeprom struct early on attach
This fixes this sparse warning:
CHECK drivers/net/wireless/ath/ath5k/attach.c
drivers/net/wireless/ath/ath5k/attach.c:288:42: warning: symbol 'ee' shadows an earlier one
drivers/net/wireless/ath/ath5k/attach.c:109:34: originally declared here
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 17:51:33 +0000 (10:51 -0700)]
ath5k: use common curbssid, bssidmask and macaddr
The ah_sta_id was really being used as the macaddr.
ath5k still does not use the association ID now passed
up by mac80211, that can be fixed later.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 17:10:54 +0000 (10:10 -0700)]
ar9170: make use of common macaddr and curbssid
These are provided by ath_common.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 16:22:37 +0000 (09:22 -0700)]
atheros/ath9k: move macaddr, curaid, curbssid and bssidmask to common
These are common amongst ath9k and ath5k, so put them into the
common structure and make ath9k to use it. ar9170 can use macaddr,
and curbssid. We'll change ath5k and ar9170 separately.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 15:57:00 +0000 (08:57 -0700)]
ath9k: use ath9k_hw_write_associd() on reset
Use the already provided helper instead of rewriting the code
required in place.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 15:54:56 +0000 (08:54 -0700)]
ath9k: Use ath9k_hw_setbssidmask() on reset
The same code was being implemented on reset for setting the bssidmask,
instead just use the already provided helper.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 15:50:20 +0000 (08:50 -0700)]
ath9k: make ath9k_hw_setbssidmask() and ath9k_hw_write_associd() use ath_hw
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 05:43:17 +0000 (22:43 -0700)]
atheros: use get_unaligned_le*() for bssid mask setting
Historically some macro helpers have been users for this,
AR5K_LOW_ID() and AR5K_HIGH_ID(), use upstream unaligned
helpers instead. This applid to ath5k and ar9170. ath9k
already uses this.
Worth noting is ath5k uses an ah_sta_id but that is already
the MAC address combined with the associaiton ID, ah_sta_id
is really ETH_ALEN in size.
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Nick Kossifidis <mick@madwifi-project.org>
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 05:19:26 +0000 (22:19 -0700)]
ath: move ath_bcast_mac to common header
This is used by both ath5k and ath9k to set the first bssid mask.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 04:10:09 +0000 (21:10 -0700)]
ath9k: rename driver core and hw power save helpers
ath9k_hw_setpower_nolock --> ath9k_hw_setpower()
ath9k_hw_setpower() --> ath9k_setpower()
Also change the param for ath9k_setpower() to pass the ath_softc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 04:02:34 +0000 (21:02 -0700)]
ath9k: move ath9k_hw_setpower() to main.c
And we make it static.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 03:54:36 +0000 (20:54 -0700)]
ath9k: avoid usage of ath9k_hw_setpower() on hw.c
ath9k_hw_setpower() is a core driver helper with locking
protection. Locking protection should be left to the driver
core, not the hw code. Hardware code no longer contends for
locking when it needs to wake up the chip or put it to sleep.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 03:29:18 +0000 (20:29 -0700)]
ath9k: move ath9k_ps_wakeup() and ath9k_ps_restore() to main.c
These are driver core helpers.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 10 Sep 2009 03:05:39 +0000 (20:05 -0700)]
ath9k: move ps helpers onto core driver when reseting tsf
When the TSF is reset power save state is disabled and
then restored. The helpers to disable power save and restore
it use a lock provided by the driver core. Move the callers
of the helpers outside of the hw code.
We reset the TSF when mac80211 tells us and on the beacon.c
helper ath9k_hw_beaconinit() when it is made explicitly required.
Add a helper on beacon.c which will deal with ps awake/restore
if we need to reset the TSF upon ath9k_hw_beaconinit().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 9 Sep 2009 23:05:32 +0000 (16:05 -0700)]
ath9k: rename ath_btcoex_supported() to ath9k_hw_btcoex_supported()
Also just pass the ath_hw as the parameter.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 9 Sep 2009 22:24:02 +0000 (15:24 -0700)]
ath9k: move ath_btcoex_config and ath_bt_mode to btcoex.c
These are only used by btcoex.c on one routine, so stuff them
into that file.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 9 Sep 2009 22:15:55 +0000 (15:15 -0700)]
ath9k: now move ath9k_hw_btcoex_set_weight() to btcoex.c
After some necessary cleanups we now move ath9k_hw_btcoex_set_weight()
to where it belongs.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 9 Sep 2009 22:05:00 +0000 (15:05 -0700)]
ath9k: simplify ath_btcoex_bt_stomp()
The second argument is always the hardware bt coex struct, so
remove it, and rename the function on the path with a ath9k_ prefix.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 9 Sep 2009 21:52:02 +0000 (14:52 -0700)]
ath9k: rename ath_btcoex_info to ath_btcoex_hw
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 9 Sep 2009 21:34:22 +0000 (14:34 -0700)]
ath9k: rename btcoex_scheme to just scheme
btcoex_scheme is already part of a btcoex struct, its implied
this is btcoex related.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 9 Sep 2009 21:31:24 +0000 (14:31 -0700)]
ath9k: remove unused bt_duty_cycle
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 9 Sep 2009 21:26:15 +0000 (14:26 -0700)]
ath9k: move bt_stomp_type to driver core
The bt_stomp_type defines the bt coex weight, it has a one-to-one
mapping. In the future we may want to just use the weight directly.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 9 Sep 2009 20:44:23 +0000 (13:44 -0700)]
ath9k: replaces SC_OP_BTCOEX_ENABLED with a bool
Whether or not bluetooth coex has been enabled is a hardware
state and only the hardware helpers will be able to set this.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 9 Sep 2009 11:17:45 +0000 (04:17 -0700)]
ath9k: split ath9k_hw_btcoex_enable() into two helpers
One for 2-wire and another for 3-wire.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 9 Sep 2009 11:00:10 +0000 (04:00 -0700)]
ath9k: move driver core helpers to main.c
Keep on btcoex.c only hardware access helpers, move the
driver core specific code to main.c. To accomplish
this we had to split ath_init_btcoex_info() into two parts,
the driver core part -- ath_init_btcoex_timer() and the hw
specific part -- ath9k_hw_init_btcoex_hw_info(). This
highlights how ath_gen_timer is part of the driver core, not
hw related, so stuff that into ath_btcoex struct.
The ath9k_hw_btcoex_init() code is now put inline on
ath_init_softc() through a switch to it easier to follow,
since we did that we can now call ath_tx_get_qnum() from
the main.c instead of btcoex.c
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 9 Sep 2009 09:54:40 +0000 (02:54 -0700)]
ath9k: split bluetooth hardware coex init into two helpers
Use a helper for 2-wire and another for 3-wire.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 9 Sep 2009 09:33:11 +0000 (02:33 -0700)]
ath9k: move hw specific btcoex info to ath_hw
Since we now access it via the ath_hw declare the ath_hw pointer
at the header of some routines and se it. ath9k.h no longer needs to
access btcoex.h and to adjust for this move ath_btcoex_set_weight()
into btcoex.h and instead give main.c a helper for setting initial
values upon drv_start()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 9 Sep 2009 08:18:09 +0000 (01:18 -0700)]
ath9k: move btcoex core driver info to its own struct
There is some bluetooth coexistance data which is driver
specific, stuff that into its own structure.
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 7 Sep 2009 11:52:26 +0000 (04:52 -0700)]
ath9k: use ath_hw for DPRINTF() and debug init/exit
DPRINTF() is used in hw specific related code, as such
ensure we don't rely on the private driver core ath_softc
struct when calling it. Drivers can then implement their
own DPRINTF() as they see fit.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andy Gospodarek [Fri, 2 Oct 2009 09:26:12 +0000 (09:26 +0000)]
net: export device speed and duplex via sysfs
This patch exports the link-speed (in Mbps) and duplex of an interface
via sysfs. This eliminates the need to use ethtool just to check the
link-speed. Not requiring 'ethtool' and not relying on the SIOCETHTOOL
ioctl should be helpful in an embedded environment where space is at a
premium as well.
NOTE: This patch also intentionally allows non-root users to check the link
speed and duplex -- something not possible with ethtool.
Here's some sample output:
# cat /sys/class/net/eth0/speed
100
# cat /sys/class/net/eth0/duplex
half
# ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: Not reported
Advertised auto-negotiation: No
Speed: 100Mb/s
Duplex: Half
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: off
Supports Wake-on: g
Wake-on: g
Current message level: 0x000000ff (255)
Link detected: yes
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel Holtmann [Fri, 2 Oct 2009 05:15:28 +0000 (05:15 +0000)]
cfg80211: assign device type in netdev notifier callback
Instead of having to modify every non-mac80211 for device type assignment,
do this inside the netdev notifier callback of cfg80211. So all drivers
that integrate with cfg80211 will export a proper device type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 2 Oct 2009 05:15:27 +0000 (05:15 +0000)]
net: introduce NETDEV_POST_INIT notifier
For various purposes including a wireless extensions
bugfix, we need to hook into the netdev creation before
before netdev_register_kobject(). This will also ease
doing the dev type assignment that Marcel was working
on for cfg80211 drivers w/o touching them all.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel Holtmann [Fri, 2 Oct 2009 05:15:26 +0000 (05:15 +0000)]
usbnet: Set device type for wlan and wwan devices
For usbnet devices with FLAG_WLAN and FLAG_WWAN set the proper device
type so that uevent contains the correct value. This then allows an easy
identification of the actual underlying technology of the Ethernet device.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel Holtmann [Fri, 2 Oct 2009 05:15:25 +0000 (05:15 +0000)]
usbnet: Use wwan%d interface name for mobile broadband devices
Add support for usbnet based devices like CDC-Ether to indicate that they
are actually mobile broadband devices. In that case use wwan%d as default
interface name.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 5 Oct 2009 07:11:22 +0000 (00:11 -0700)]
tunnels: Optimize tx path
We currently dirty a cache line to update tunnel device stats
(tx_packets/tx_bytes). We better use the txq->tx_bytes/tx_packets
counters that already are present in cpu cache, in the cache
line shared with txq->_xmit_lock
This patch extends IPTUNNEL_XMIT() macro to use txq pointer
provided by the caller.
Also &tunnel->dev->stats can be replaced by &dev->stats
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Sun, 20 Sep 2009 10:35:36 +0000 (10:35 +0000)]
ipv4: fib table algorithm performance improvement
The FIB algorithim for IPV4 is set at compile time, but kernel goes through
the overhead of function call indirection at runtime. Save some
cycles by turning the indirect calls to direct calls to either
hash or trie code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Fri, 2 Oct 2009 06:56:41 +0000 (06:56 +0000)]
af_packet: add interframe drop cmsg (v6)
Add Ancilliary data to better represent loss information
I've had a few requests recently to provide more detail regarding frame loss
during an AF_PACKET packet capture session. Specifically the requestors want to
see where in a packet sequence frames were lost, i.e. they want to see that 40
frames were lost between frames 302 and 303 in a packet capture file. In order
to do this we need:
1) The kernel to export this data to user space
2) The applications to make use of it
This patch addresses item (1). It does this by doing the following:
A) Anytime we drop a frame for which we would increment po->stats.tp_drops, we
also no increment a stats called po->stats.tp_gap.
B) Every time we successfully enqueue a frame to sk_receive_queue, we record the
value of po->stats.tp_gap in skb->mark. skb->cb would nominally be the place to
record this, but since all the space there is used up, we're overloading
skb->mark. Its safe to do since any enqueued packet is guaranteed to be
unshared at this point, and skb->mark isn't used for anything else in the rx
path to the application. After we record tp_gap in the skb, we zero
po->stats.tp_gap. This allows us to keep a counter of the number of frames lost
between any two enqueued packets
C) When the application goes to dequeue a frame from the packet socket, we look
at skb->mark for that frame. If it is non-zero, we add a cmsg chunk to the
msghdr of level SOL_PACKET and type PACKET_GAPDATA. Its a 32 bit integer that
represents the number of frames lost between this packet and the last previous
frame received.
Note there is a chance that if there is frame loss after a receive, and then the
socket is closed, some gap data might be lost. This is covered by the use of
the PACKET_AUXDATA socket option, which gives total loss data. With a bit of
math, the final gap can be determined that way.
I've tested this patch myself, and it works well.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
include/linux/if_packet.h | 2 ++
net/packet/af_packet.c | 33 +++++++++++++++++++++++++++++++++
2 files changed, 35 insertions(+)
Signed-off-by: David S. Miller <davem@davemloft.net>
chaithrika@ti.com [Thu, 1 Oct 2009 10:25:19 +0000 (10:25 +0000)]
TI DaVinci EMAC: Minor macro related updates
Use BIT for macro definitions wherever possible, remove
unused and redundant macros.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 30 Sep 2009 13:03:33 +0000 (13:03 +0000)]
pktgen: Avoid dirtying skb->users when txq is full
We can avoid two atomic ops on skb->users if packet is not going to be
sent to the device (because hardware txqueue is full)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 24 Sep 2009 12:16:51 +0000 (12:16 +0000)]
icmp: No need to call sk_write_space()
We can make icmp messages tx completion callback a litle bit faster.
Setting SOCK_USE_WRITE_QUEUE sk flag tells sock_wfree() to
not call sk_write_space() on a socket we know no thread is posssibly
waiting for write space. (on per cpu kernel internal icmp sockets only)
This avoids the sock_def_write_space() call and
read_lock(&sk->sk_callback_lock)/read_unlock(&sk->sk_callback_lock) calls
as well.
We avoid three atomic ops.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 1 Oct 2009 11:33:03 +0000 (11:33 +0000)]
ethtool: Remove support for obsolete string query operations
The in-tree implementations have all been converted to
get_sset_count().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 1 Oct 2009 11:58:24 +0000 (11:58 +0000)]
net: Convert ethtool {get_stats, self_test}_count() ops to get_sset_count()
These string query operations were supposed to be replaced by the
generic get_sset_count() starting in 2007. Convert the remaining
implementations.
Also remove calls to these operations to initialise drvinfo->n_stats.
The ethtool core code already does that.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 1 Oct 2009 11:27:59 +0000 (11:27 +0000)]
tehuti: Convert ethtool get_stats_count() ops to get_sset_count()
This string query operation was supposed to be replaced by the
generic get_sset_count() starting in 2007. Convert tehuti's
implementation.
Also remove the dummy self-test name which was not used since tehuti
does not advertise any self-tests.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 1 Oct 2009 11:24:32 +0000 (11:24 +0000)]
qeth: Convert ethtool get_stats_count() ops to get_sset_count()
This string query operation was supposed to be replaced by the
generic get_sset_count() starting in 2007. Convert qeth's
implementation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 5 Oct 2009 00:12:30 +0000 (17:12 -0700)]
Linux 2.6.32-rc3
I'm skipping -rc2 because the -rc1 Makefile mistakenly said -rc2, so in
order to avoid confusion, I'm jumping from -rc1 to -rc3. That way, when
'uname' (or an oops report) says 2.6.32-rc2, there's no confusion about
whether people perhaps meant -rc1 or -rc2.
Alexey Dobriyan [Sun, 4 Oct 2009 12:11:37 +0000 (16:11 +0400)]
headers: remove sched.h from poll.h
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 4 Oct 2009 22:03:00 +0000 (15:03 -0700)]
Merge branch 'acpi-pad' of git://git./linux/kernel/git/lenb/linux-acpi-2.6
* 'acpi-pad' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
acpi_pad: build only on X86
ACPI: create Processor Aggregator Device driver
Fixup trivial conflicts in MAINTAINERS file.
Linus Torvalds [Sun, 4 Oct 2009 22:00:08 +0000 (15:00 -0700)]
Merge branch 'sfi-release' of git://git./linux/kernel/git/lenb/linux-sfi-2.6
* 'sfi-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-sfi-2.6:
SFI: remove __init from sfi_verify_table
SFI: fix section mismatch warnings in sfi_core.c
Linus Torvalds [Sun, 4 Oct 2009 21:59:53 +0000 (14:59 -0700)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: EC: Don't parse DSDT for EC early init on Compal
ACPI: EC: Rewrite DMI checks
ACPI: dock: fix "sibiling" typo
ACPI: kill overly verbose "throttling states" log messages
ACPI: Fix bound checks for copy_from_user in the acpi /proc code
ACPI: fix bus scanning memory leaks
ACPI: EC: Restart command even if no interrupts from EC
sony-laptop: Don't unregister the SPIC driver if it wasn't registered
sony-laptop: remove _INI call at init time
sony-laptop: SPIC unset IRQF_SHARED, set IRQF_DISABLED
sony-laptop: remove device_ctrl and the SPIC mini drivers
Linus Torvalds [Sun, 4 Oct 2009 21:59:14 +0000 (14:59 -0700)]
Merge branch 'i2c-for-linus' of git://git./linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
macintosh: Don't assume i2c device probing always succeeds
i2c: Hide probe errors caused by ACPI resource conflicts
i2c: Minor documentation update
mfd: AB3100 drop unused module parameters
Staging: IIO: tsl2561: Drop unused module parameters
leds: leds-pca9532 - Drop unused module parameters
ltc4215/ltc4245: Discard obsolete detect methods
ds2482: Discard obsolete detect method
max6875: Discard obsolete detect method
i2c: Move misc devices documentation
Jean Delvare [Sun, 4 Oct 2009 20:53:46 +0000 (22:53 +0200)]
macintosh: Don't assume i2c device probing always succeeds
If i2c device probing fails, then there is no driver to dereference
after calling i2c_new_device(). Stop assuming that probing will always
succeed, to avoid NULL pointer dereferences. We have an easier access
to the driver anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Tim Shepard <shep@alum.mit.edu>
Cc: Colin Leroy <colin@colino.net>
Jean Delvare [Sun, 4 Oct 2009 20:53:45 +0000 (22:53 +0200)]
i2c: Hide probe errors caused by ACPI resource conflicts
When an ACPI resource conflict is detected, error messages are already
printed by ACPI. There's no point in causing the driver core to print
more error messages, so return one of the error codes for which no
message is printed.
This fixes bug #14293:
http://bugzilla.kernel.org/show_bug.cgi?id=14293
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Sun, 4 Oct 2009 20:53:45 +0000 (22:53 +0200)]
i2c: Minor documentation update
The sysfs path to i2c adapters has changed recently, update the
documentation to reflect that change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Sun, 4 Oct 2009 20:53:44 +0000 (22:53 +0200)]
mfd: AB3100 drop unused module parameters
The I2C_CLIENT_INSMOD_1 macro is only useful for i2c drivers which
implement device detection. The ab3100 driver doesn't, so there is no
point in calling it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Jean Delvare [Sun, 4 Oct 2009 20:53:43 +0000 (22:53 +0200)]
Staging: IIO: tsl2561: Drop unused module parameters
The I2C_CLIENT_INSMOD macro is only useful for i2c drivers which
implement device detection. The tsl2561 driver doesn't, so there
is no point in calling it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Jean Delvare [Sun, 4 Oct 2009 20:53:43 +0000 (22:53 +0200)]
leds: leds-pca9532 - Drop unused module parameters
The I2C_CLIENT_INSMOD_1 macro is only useful for i2c drivers which
implement device detection. The leds-pca9532 driver doesn't, so there
is no point in calling it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Riku Voipio <riku.voipio@iki.fi>
Jean Delvare [Sun, 4 Oct 2009 20:53:42 +0000 (22:53 +0200)]
ltc4215/ltc4245: Discard obsolete detect methods
There is no point in implementing a detect callback for the LTC4215
and LTC4245, as these devices can't be detected. It was there solely
to handle "force" module parameters to instantiate devices, but now
we have a better sysfs interface that can do the same.
So we can get rid of the ugly module parameters and the detect
callbacks. This shrinks the binary module sizes by 36% and 46%,
respectively.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Jean Delvare [Sun, 4 Oct 2009 20:53:41 +0000 (22:53 +0200)]
ds2482: Discard obsolete detect method
There is no point in implementing a detect callback for the DS2482, as
this device can't be detected. It was there solely to handle "force"
module parameters to instantiate devices, but now we have a better sysfs
interface that can do the same.
So we can get rid of the ugly module parameters and the detect callback.
This shrinks the binary module size by 21%.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Gardner <gardner.ben@gmail.com>
Jean Delvare [Sun, 4 Oct 2009 20:53:41 +0000 (22:53 +0200)]
max6875: Discard obsolete detect method
There is no point in implementing a detect callback for the MAX6875, as
this device can't be detected. It was there solely to handle "force"
module parameters to instantiate devices, but now we have a better sysfs
interface that can do the same.
So we can get rid of the ugly module parameters and the detect callback.
This basically divides the binary module size by 2.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Ben Gardner <gardner.ben@gmail.com>
Jean Delvare [Sun, 4 Oct 2009 20:53:40 +0000 (22:53 +0200)]
i2c: Move misc devices documentation
Some times ago the eeprom and max6875 drivers moved to
drivers/misc/eeprom, but their documentation did not follow. It's
finally time to get rid of Documentation/i2c/chips.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Gardner <gardner.ben@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Linus Torvalds [Sun, 4 Oct 2009 19:39:14 +0000 (12:39 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (41 commits)
Revert "Seperate read and write statistics of in_flight requests"
cfq-iosched: don't delay async queue if it hasn't dispatched at all
block: Topology ioctls
cfq-iosched: use assigned slice sync value, not default
cfq-iosched: rename 'desktop' sysfs entry to 'low_latency'
cfq-iosched: implement slower async initiate and queue ramp up
cfq-iosched: delay async IO dispatch, if sync IO was just done
cfq-iosched: add a knob for desktop interactiveness
Add a tracepoint for block request remapping
block: allow large discard requests
block: use normal I/O path for discard requests
swapfile: avoid NULL pointer dereference in swapon when s_bdev is NULL
fs/bio.c: move EXPORT* macros to line after function
Add missing blk_trace_remove_sysfs to be in pair with blk_trace_init_sysfs
cciss: fix build when !PROC_FS
block: Do not clamp max_hw_sectors for stacking devices
block: Set max_sectors correctly for stacking devices
cciss: cciss_host_attr_groups should be const
cciss: Dynamically allocate the drive_info_struct for each logical drive.
cciss: Add usage_count attribute to each logical drive in /sys
...
Jens Axboe [Sun, 4 Oct 2009 19:04:38 +0000 (21:04 +0200)]
Revert "Seperate read and write statistics of in_flight requests"
This reverts commit
a9327cac440be4d8333bba975cbbf76045096275.
Corrado Zoccolo <czoccolo@gmail.com> reports:
"with 2.6.32-rc1 I started getting the following strange output from
"iostat -kx 2":
Linux 2.6.31bisect (et2) 04/10/2009 _i686_ (2 CPU)
avg-cpu: %user %nice %system %iowait %steal %idle
10,70 0,00 3,16 15,75 0,00 70,38
Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s
avgrq-sz avgqu-sz await svctm %util
sda 18,22 0,00 0,67 0,01 14,77 0,02
43,94 0,01 10,53
39043915,03
2629219,87
sdb 60,89 9,68 50,79 3,04 1724,43 50,52
65,95 0,70 13,06 488437,47
2629219,87
avg-cpu: %user %nice %system %iowait %steal %idle
2,72 0,00 0,74 0,00 0,00 96,53
Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s
avgrq-sz avgqu-sz await svctm %util
sda 0,00 0,00 0,00 0,00 0,00 0,00
0,00 0,00 0,00 0,00 100,00
sdb 0,00 0,00 0,00 0,00 0,00 0,00
0,00 0,00 0,00 0,00 100,00
avg-cpu: %user %nice %system %iowait %steal %idle
6,68 0,00 0,99 0,00 0,00 92,33
Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s
avgrq-sz avgqu-sz await svctm %util
sda 0,00 0,00 0,00 0,00 0,00 0,00
0,00 0,00 0,00 0,00 100,00
sdb 0,00 0,00 0,00 0,00 0,00 0,00
0,00 0,00 0,00 0,00 100,00
avg-cpu: %user %nice %system %iowait %steal %idle
4,40 0,00 0,73 1,47 0,00 93,40
Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s
avgrq-sz avgqu-sz await svctm %util
sda 0,00 0,00 0,00 0,00 0,00 0,00
0,00 0,00 0,00 0,00 100,00
sdb 0,00 4,00 0,00 3,00 0,00 28,00
18,67 0,06 19,50 333,33 100,00
Global values for service time and utilization are garbage. For
interval values, utilization is always 100%, and service time is
higher than normal.
I bisected it down to:
[
a9327cac440be4d8333bba975cbbf76045096275] Seperate read and write
statistics of in_flight requests
and verified that reverting just that commit indeed solves the issue
on 2.6.32-rc1."
So until this is debugged, revert the bad commit.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Jens Axboe [Sun, 4 Oct 2009 18:36:19 +0000 (20:36 +0200)]
cfq-iosched: don't delay async queue if it hasn't dispatched at all
We cannot delay for the first dispatch of the async queue if it
hasn't dispatched at all, since that could present a local user
DoS attack vector using an app that just did slow timed sync reads
while filling memory.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Linus Torvalds [Sun, 4 Oct 2009 04:57:06 +0000 (21:57 -0700)]
Merge branch 'for-linus' of git://linux-m32r.org/git/takata/linux-2.6_dev
* 'for-linus' of git://www.linux-m32r.org/git/takata/linux-2.6_dev:
m32r: Fix IPI function calls for SMP
m32r: Fix set_memory() for DISCONTIGMEM
m32r: add rtc_lock variable
m32r: define ioread* and iowrite* macros
m32r: export delay loop symbols
m32r: fix tme_handler
Linus Torvalds [Sun, 4 Oct 2009 04:44:21 +0000 (21:44 -0700)]
tty: Avoid dropping ldisc_mutex over hangup tty re-initialization
A couple of people have hit the WARN_ON() in drivers/char/tty_io.c,
tty_open() that is unhappy about seeing the tty line discipline go away
during the tty hangup. See for example
http://bugzilla.kernel.org/show_bug.cgi?id=14255
and the reason is that we do the tty_ldisc_halt() outside the
ldisc_mutex in order to be able to flush the scheduled work without a
deadlock with vhangup_work.
However, it turns out that we can solve this particular case by
- using "cancel_delayed_work_sync()" in tty_ldisc_halt(), which waits
for just the particular work, rather than synchronizing with any
random outstanding pending work.
This won't deadlock, since the buf.work we synchronize with doesn't
care about the ldisc_mutex, it just flushes the tty ldisc buffers.
- realize that for this particular case, we don't need to wait for any
hangup work, because we are inside the hangup codepaths ourselves.
so as a result we can just drop the flush_scheduled_work() entirely, and
then move the tty_ldisc_halt() call to inside the mutex. That way we
never expose the partially torn down ldisc state to tty_open(), and hold
the ldisc_mutex over the whole sequence.
Reported-by: Ingo Molnar <mingo@elte.hu>
Reported-by: Heinz Diehl <htd@fancy-poultry.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Toshihiro HANAWA [Fri, 2 Oct 2009 08:52:54 +0000 (17:52 +0900)]
m32r: Fix IPI function calls for SMP
This patch fixes the m32r SMP kernel after 2.6.27.
A part of the following patch breaks m32r SMP operation.
> m32r: convert to generic helpers for IPI function calls
> commit
7b7426c8a615cf61df9a77b9df7d5b75d91e3fa0
In the above patch, a CALL_FUNC_SINGLE_IPI was newly introduced,
but the its IPI vector number was wrong in the patch code.
The m32r SMP kernel hanged-up during boot operation, because
the CPU_BOOT_IPI was called instead of CALL_FUNC_SINGLE_IPI
(CPU_BOOT_IPI had no side effect at that time because the 2nd
core had already been started up),
as a result, csd_unlock() was not called, then a dead lock
occurred in csd_lock_wait() after the detection of Compact Flash
memory as IDE generic disk.
Signed-off-by: Toshihiro HANAWA <hanawa@ccs.tsukuba.ac.jp>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Hirokazu Takata [Wed, 23 Sep 2009 12:37:06 +0000 (21:37 +0900)]
m32r: Fix set_memory() for DISCONTIGMEM
In case CONFIG_DISCONTIGMEM is set, the memory size of system was
always determined by CONFIG_MEMORY_SIZE and was not changeable.
This patch fixes set_memory() of arch/m32r/mm/discontig.c so that
we can specify memory size by the "mem=<size>" kernel parameter.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Hirokazu Takata [Wed, 26 Aug 2009 04:13:12 +0000 (13:13 +0900)]
m32r: add rtc_lock variable
Add a spinlock variable "rtc_lock".
This is taken from arch/arm/kernel/time.c.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Hirokazu Takata [Wed, 26 Aug 2009 04:04:33 +0000 (13:04 +0900)]
m32r: define ioread* and iowrite* macros
Define ioread* and iowrite* macros to fix the following build errors:
CC [M] drivers/uio/uio_smx.o
drivers/uio/uio_smx.c: In function 'smx_handler':
drivers/uio/uio_smx.c:31: error: implicit declaration of function 'ioread32'
drivers/uio/uio_smx.c:37: error: implicit declaration of function 'iowrite32'
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>