OSDN Git Service
Ezequiel Garcia [Wed, 23 Jan 2013 15:26:31 +0000 (12:26 -0300)]
arm: mvebu: Enable USB controllers on Armada 370/XP boards
This patch activates every USB port provided by each SoC.
Except for Armada XP Openblocks AX3-4 board,
where we enable only the first two USB ports
until we have more information on the third one usage.
Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ezequiel Garcia [Wed, 23 Jan 2013 15:26:30 +0000 (12:26 -0300)]
arm: mvebu: Add support for USB host controllers in Armada 370/XP
The Armada 370 and Armada XP SoC has an Orion EHCI USB controller.
This patch adds support for this controller in Armada 370
and Armada XP SoC common device tree files.
Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Mon, 7 Jan 2013 16:29:58 +0000 (17:29 +0100)]
arm: mvebu: add button for OpenBlocks AX3-4
The OpenBlocks AX3-4 board has one software-controlled button on the
front side, labeled "INIT", so we add minimal support for this button
in the kernel.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Andrew Lunn [Fri, 28 Dec 2012 14:14:10 +0000 (15:14 +0100)]
ARM: Kirkwood: Convert NS2 to gpio-poweroff.
Remove C code and add a Device Tree node in its place.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Andrew Lunn [Fri, 28 Dec 2012 14:08:50 +0000 (15:08 +0100)]
ARM: Kirkwood: Convert NSA310 I2C to device tree
Add a sub-node into the I2C node to represent the adt7476 device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Andrew Lunn [Fri, 28 Dec 2012 14:08:49 +0000 (15:08 +0100)]
ARM: Kirkwood: Convert NSA310 to use gpio-poweroff driver
Remove the C code and add a Device Tree node for gpio-poweroff.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Andrew Lunn [Fri, 28 Dec 2012 14:08:48 +0000 (15:08 +0100)]
ARM: Kirkwood: Convert NSA310 to DT based regulators.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Sebastian Hesselbarth [Thu, 27 Dec 2012 22:21:59 +0000 (23:21 +0100)]
ARM: Dove: add fixed regulator for CuBox USB power
CuBox needs to enable USB power on a gpio pin. Add a fixed regulator
to always enable usb power on boot.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Sebastian Hesselbarth [Thu, 27 Dec 2012 22:21:10 +0000 (23:21 +0100)]
ARM: Dove: move CuBox led pinctrl to gpio-leds node
gpio-leds has support for pinctrl allocation, make use of it.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Nobuhiro Iwamatsu [Sun, 23 Dec 2012 02:34:37 +0000 (11:34 +0900)]
ARM: Kirkwood: Convert openblocks A6 board to pinctrl
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Nobuhiro Iwamatsu [Sun, 23 Dec 2012 02:34:36 +0000 (11:34 +0900)]
ARM: Kirkwood: Add pinctrl of NAND to
88f6282
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Nobuhiro Iwamatsu [Sun, 23 Dec 2012 02:34:34 +0000 (11:34 +0900)]
ARM: Kirkwood: Add pinctrl of TWSI1 to
88f6282
The
88f6282 has one more TWSI(TWSI1). This add the information to enable
pinctl of TWSI1.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 21 Dec 2012 14:49:13 +0000 (15:49 +0100)]
arm: kirkwood: add pinmux option for the SDIO interface on
88F6282
This commit adds a pinmux option, pmx_sdio, to enable the muxing of
the SDIO interface on the
88F6282 SoC from Marvell.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 21 Dec 2012 14:49:12 +0000 (15:49 +0100)]
arm: kirkwood: mplcec4: use Device Tree to probe SDIO
Now that the mvsdio driver has a Device Tree binding, and the SDIO
controller is declared in kirkwood.dtsi, migrate the mplcec4 board to
use the Device Tree to probe the SDIO controller and to mux the pins
of the SDIO interface correctly.
This patch has not been tested, it remains to be tested by a person
having access to the hardware.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Stefan Peter <s.peter@mpl.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 21 Dec 2012 14:49:11 +0000 (15:49 +0100)]
arm: kirkwood: dreamplug: use Device Tree to probe SDIO
Now that the mvsdio driver has a Device Tree binding, and the SDIO
controller is declared in kirkwood.dtsi, migrate the dreamplug board
to use the Device Tree to probe the SDIO controller and to mux this
interface properly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 21 Dec 2012 14:49:10 +0000 (15:49 +0100)]
arm: kirkwood: add Device Tree informations for the SDIO controller
Now that the SDIO controller has a Device Tree binding, let's use it
in kirkwood.dtsi.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 21 Dec 2012 14:49:09 +0000 (15:49 +0100)]
arm: mvebu: enable the SDIO interface on the Globalscale Mirabox
The Globalscale Mirabox uses the SDIO interface of the Armada 370 to
connect to a Wifi/Bluetooth SD8787 chip, so we enable the SDIO
interface of this board in its Device Tree file.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 21 Dec 2012 14:49:08 +0000 (15:49 +0100)]
arm: mvebu: enable the SD card slot on Armada 370 DB board
The Armada XP DB evaluation board has one SD card slot, directly
connected to the SDIO IP of the SoC, so we add a device tree
description for it.
However, in the default configuration of the board, the SD card slot
is not usable: the connector plugged into CON40 must be changed
against a different one, provided with the board by the
manufacturer. Since such a manual modification of the hardware is
needed, we did not enable the SDIO interface by default, and left it
to the board user to modify the Device Tree if needed. Since this
board is really only an evaluation board for developers and not a
final product, it is not too bad.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 21 Dec 2012 14:49:07 +0000 (15:49 +0100)]
arm: mvebu: enable the SD card slot on Armada XP DB board
The Armada XP DB evaluation board has one SD card slot, directly
connected to the SDIO IP of the SoC, so we enable this
IP. Unfortunately, there are no GPIOs for card-detect and
write-protect.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 21 Dec 2012 14:49:06 +0000 (15:49 +0100)]
arm: mvebu: add pin muxing options for the SDIO interface on Armada XP
The SDIO interface is only available on pins MPP30/31/32/33/34/35 on
the various Armada XP variants, so we provide a pin muxing option for
this in the Armada XP .dtsi files.
Even though those muxing options are the same for MV78230, MV78260 and
MV78460, we keep them in each .dtsi file, because the number of pins,
and therefore the declaration of the pinctrl node, is different for
each SoC variant.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 21 Dec 2012 14:49:05 +0000 (15:49 +0100)]
arm: mvebu: add pin muxing options for the SDIO interface on Armada 370
The SDIO interface is available either on pins MPP9/11/12/13/14/15 or
MPP47/48/49/50/51/52 on the Armada 370. Even though all combinations
are potentially possible, those two muxing options are the most
probable ones, so we provide those at the SoC level .dtsi file.
In practice, in turns out the Armada 370 DB board uses the former,
while the Armada 370 Mirabox uses the latter.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 21 Dec 2012 14:49:04 +0000 (15:49 +0100)]
arm: mvebu: add DT information for the SDIO interface of Armada 370/XP
Now that the mvsdio MMC driver has a Device Tree binding, we add the
Device Tree informations to describe the SDIO interface available in
the Armada 370/XP SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Gregory CLEMENT [Wed, 12 Dec 2012 09:06:24 +0000 (10:06 +0100)]
arm: mvebu: Add RTC support for Armada 370 and Armada XP
The Armada 370 and Armada XP Socs have the same controller that the
one used in the orion platforms. This patch updates the device tree
for these SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Gregory CLEMENT [Mon, 4 Feb 2013 17:21:07 +0000 (18:21 +0100)]
arm: mvebu: update defconfig with ATAG support when using DT
Some of the mvebu boards (mainly the development board) come with
plug-in RAM modules. This patch allows to let the bootloaders which
have no support for DTS to give the real amount of memory available on
the board.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ezequiel Garcia [Wed, 6 Feb 2013 13:06:24 +0000 (10:06 -0300)]
ARM: mvebu: Update defconfig to select SPI flash and MTD support
The Armada XP DB-MV784MP-GP board has an SPI flash device.
These options allow to access that device over MTD.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ezequiel Garcia [Wed, 6 Feb 2013 13:06:22 +0000 (10:06 -0300)]
ARM: mvebu: Update defconfig to select SPI support
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Acked-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Gregory CLEMENT [Thu, 31 Jan 2013 14:50:12 +0000 (15:50 +0100)]
arm: mvebu: support for the new Armada XP development board(DB-MV784MP-GP)
This is the new Armada XP evaluation board from Marvell. It comes with
a RS232 port over USB, a SATA link, an internal SSD, 4 Ethernet
Gigabit links.
Support for USB (Host and device), SDIO, PCIe will be added as drivers
when they become available for Armada XP in mainline.
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Gregory CLEMENT [Fri, 25 Jan 2013 17:32:43 +0000 (18:32 +0100)]
arm: mvebu: update defconfig with local timer support
Now that we have support for local timers, enable it by default
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Gregory CLEMENT [Fri, 25 Jan 2013 17:32:42 +0000 (18:32 +0100)]
clocksource: time-armada-370-xp: add local timer support
On the SOCs Armada 370 and Armada XP, each CPU comes with two private
timers. This patch use the timer 0 of each CPU as local timer for the
clockevent if CONFIG_LOCAL_TIMER is selected. In the other case, use
only the private Timer 0 of CPU 0.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Gregory CLEMENT [Fri, 25 Jan 2013 17:32:41 +0000 (18:32 +0100)]
arm: mvebu: Add support for local interrupt
MPIC allows the use of private interrupt for each CPUs. The 28th first
interrupts are per-cpu. This patch adds support to use them.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ezequiel Garcia [Wed, 23 Jan 2013 15:26:32 +0000 (12:26 -0300)]
arm: mvebu: Update defconfig to select USB support
Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Willy Tarreau [Sun, 9 Dec 2012 18:40:04 +0000 (19:40 +0100)]
ARM: kirkwood: convert Guruplug Server Plus to use the device tree
Add a device tree entry for the Guruplug Server Plus board. This port
was based both on the work done on the dreamplug and the dockstar.
It builds, boots and works on my Guruplug Server Plus.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Florian Fainelli [Wed, 9 Jan 2013 19:56:07 +0000 (20:56 +0100)]
arm: mvebu: add DTS file for Marvell RD-A370-A1 board
This patch adds the DTS file to support the Marvell RD-A370-A1
(Reference Design board) also known as RD-
88F6710 board. It is almost
entirely similar to the DB-A370 board except that the first Ethernet PHY
is SGMII-wired and the second is a switch which is RGMII-wired.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Gregory CLEMENT [Wed, 5 Dec 2012 20:43:23 +0000 (21:43 +0100)]
arm: mvebu: Improve the SMP support of the interrupt controller
This patch makes the interrupt controller driver more SMP aware for
the Armada XP SoCs. It adds the support for the per-CPU irq. It also
adds the implementation for the set_affinity hook.
Patch initialy wrote by Yehuda Yitschak and reworked by Gregory
CLEMENT.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Arnd Bergmann [Thu, 28 Feb 2013 17:19:16 +0000 (18:19 +0100)]
ARM: Dove: split legacy and DT setup
In the beginning of DT for Dove it was reasonable to have it close to
non-DT code. With improved DT support, it became more and more difficult
to not break non-DT while changing DT code.
This patch splits up DT board setup and introduces a DOVE_LEGACY config
to allow to remove legacy code for DT-only kernels.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Olof Johansson [Sun, 13 Jan 2013 17:54:07 +0000 (09:54 -0800)]
ARM: dove: update dove_defconfig with a few useful options
This refreshes the dove_defconfig, and adds:
PRINTK_TIME
DEVTMPFS
EXT4
They're quite useful, and allows booting a cubox ubuntu rootfs on SD card,
since that by default uses ext4.
The rest of the churn is due to options and defaults moving around, no
functional difference.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Andrew Lunn [Thu, 10 Jan 2013 21:01:09 +0000 (22:01 +0100)]
ARM: Kirkwood: Remove redundent SDIO clock alias
Now that SDIO is instantiated via DT, and the SDIO DT node has a clocks
property, we no longer need a C coded clock alias. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Andrew Lunn [Thu, 10 Jan 2013 21:01:08 +0000 (22:01 +0100)]
ARM: Kirkwood: Remove redundent USB clock alias
Now that USB is instantiated via DT, and the USB DT node has a clocks
property, we no longer need a C coded clock alias. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Mon, 7 Jan 2013 16:27:14 +0000 (17:27 +0100)]
arm: mvebu: add LEDs support to defconfig file
The OpenBlocks AX3-4 platform has several LEDs, so it sounds wise to
enable LED support in mvebu_defconfig. We anticipate that more
platforms using Marvell EBU SoCs will have LEDs in the future.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 21 Dec 2012 14:49:19 +0000 (15:49 +0100)]
arm: mvebu: enable btmrvl driver in mvebu_defconfig
The Globalscale Mirabox platform, based on the Armada 370 from
Marvell, has a SD8787 Wireless/Bluetooth chip connected on the SDIO
interface. Now that the mvsdio has a Device Tree binding, and the
necessary Device Tree informations have been added at the SoC and
board level, let's enable the btmrvl driver for the Bluetooth part of
the SD8787 chip.
For now, the driver gets probed correctly, detects the device but
apparently fails to push the firmware to the device:
Bluetooth: vendor=0x2df, device=0x911a, class=255, fn=2
Bluetooth: FW failed to be active in time!
Bluetooth: Downloading firmware failed!
Bluetooth: vendor=0x2df, device=0x911b, class=255, fn=3
Bluetooth: FW failed to be active in time!
Bluetooth: Downloading firmware failed!
This will have to be investigated separately.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 21 Dec 2012 14:49:18 +0000 (15:49 +0100)]
arm: mvebu: enable mwifiex driver in mvebu_defconfig
The Globalscale Mirabox platform, based on the Armada 370 from
Marvell, has a SD8787 Wireless chip connected on the SDIO
interface. Now that the mvsdio has a Device Tree binding, and the
necessary Device Tree informations have been added at the SoC and
board level, let's enable the mwifiex driver for the Wireless part of
the SD8787 chip.
For now, the driver gets probed correctly, detects a device and shows
the network interfaces. However, scanning Wifi networks doesn't work
for now, with a 'CMD_RESP: cmd 0x6 error, result=0x1' message. This
will have to be investigated separately.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 21 Dec 2012 14:49:17 +0000 (15:49 +0100)]
arm: mvebu: enable SDIO support in mvebu_defconfig
Now that the mvsdio driver has gained Device Tree support and the
necessary Device Tree informations has been added for Armada 370 and
Armada XP platforms, we enable the MMC subsystem and the mvsdio driver
in mvebu_defconfig.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Gregory CLEMENT [Wed, 12 Dec 2012 09:06:26 +0000 (10:06 +0100)]
arm: mvebu: Update defconfig with Marvell RTC support
The RTC class driver is already part of the mvebu_defconfig but the
Marvell internal RTC not yet. Now that its support is added for mvebu
let's update the config file.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Arnd Bergmann [Thu, 28 Feb 2013 17:54:15 +0000 (18:54 +0100)]
Merge branch 'timer/cleanup' into late/mvebu2
Basing the mvebu patches on top of the timer cleanup
avoids some nasty merges.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 28 Feb 2013 17:53:01 +0000 (18:53 +0100)]
Merge 'mmc/upstream' into late/mvebu2
These patches from the mmc tree were merged into v3.9 already
and the later mvebu patches depend on them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Thomas Petazzoni [Mon, 28 Jan 2013 11:26:53 +0000 (06:26 -0500)]
mmc: mvsdio: add pinctrl integration
On many Marvell SoCs, the pins used for the SDIO interface are part of
the MPP pins, that are muxable pins. In order to get the muxing of
those pins correct, this commit integrates the mvsdio driver with the
pinctrl infrastructure by calling devm_pinctrl_get_select_default()
during ->probe().
Note that we permit this function to fail because not all Marvell
platforms have yet been fully converted to using the pinctrl
infrastructure.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
Thomas Petazzoni [Wed, 16 Jan 2013 13:13:59 +0000 (14:13 +0100)]
mmc: mvsdio: implement a Device Tree binding
This patch adds a simple Device Tree binding for the mvsdio driver, as
well as the necessary documentation for it. Compatibility with non-DT
platforms is preserved, by keeping the platform_data based
initialization.
We introduce a small difference between non-DT and DT platforms: DT
platforms are required to provide a clocks = <...> property, which the
driver uses to get the frequency of the clock that goes to the SDIO
IP. The behaviour on non-DT platforms is kept unchanged: a clock
reference is not mandatory, but the clock frequency must be passed in
the "clock" field of the mvsdio_platform_data structure.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
Thomas Petazzoni [Wed, 16 Jan 2013 13:13:58 +0000 (14:13 +0100)]
mmc: mvsdio: use slot-gpio for card detect gpio
The MMC core subsystem provides in drivers/mmc/core/slot-gpio.c a nice
set of helper functions to simplify the management of the card detect
GPIO in MMC host drivers. This patch migrates the mvsdio driver to
using those helpers, which will make the ->probe() code simpler, and
therefore ease the process of adding a Device Tree binding for this
driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
Thomas Petazzoni [Wed, 16 Jan 2013 13:13:57 +0000 (14:13 +0100)]
mmc: mvsdio: use slot-gpio infrastructure for write protect gpio
The MMC core subsystem provides in drivers/mmc/core/slot-gpio.c a nice
set of helper functions to simplify the management of the write
protect GPIO in MMC host drivers. This patch migrates the mvsdio
driver to using those helpers, which will make the ->probe() code
simpler, and therefore ease the process of adding a Device Tree
binding for this driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
Shawn Guo [Tue, 15 Jan 2013 15:19:54 +0000 (23:19 +0800)]
mmc: sdhci-esdhc-imx: remove ESDHC_CD_GPIO handling from IO accessory
With commit
9444e07 (mmc: remove unncessary mmc_gpio_free_cd() call from
slot-gpio users) in place, the ESDHC_CD_GPIO handling in IO accessories
becomes unnecessary. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Andy Shevchenko [Mon, 7 Jan 2013 14:31:08 +0000 (16:31 +0200)]
mmc: sdhci: introduce sdhci_update_clock helper to re-enable clock
There are three places where same piece of code is used. Let's split it
to a separate function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Kevin Liu [Mon, 14 Jan 2013 19:38:53 +0000 (14:38 -0500)]
mmc: sdhci-pxav3: add IRQ wake up support
[cjb: The MMP3 architecture requires a registered interrupt to retire wfi
when waking from suspend.]
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Kevin Liu [Sat, 5 Jan 2013 09:21:33 +0000 (17:21 +0800)]
mmc: sdhci: add IRQ wake up support
Don't disable SD Host IRQ during suspend if it is wake up source.
Enable wakeup event during suspend.
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Kevin Liu [Sat, 5 Jan 2013 09:18:28 +0000 (17:18 +0800)]
mmc: sdhci: disable interrupt before free_irq
Current code missed disabling interrupts before free irq which is shared.
Notice below comments for function free_irq (kernel/irq/manage.c):
On a shared IRQ the caller must ensure the interrupt is disabled
on the card it drives before calling this function.
Original code has below issue during suspend/resume when multiple SD
hosts share the same IRQ:
1. Assume there are two hosts (host1 for emmc while host2 for sd) share
the same mmc irq.
2. When system suspend, host2 will be suspended before host1.
So the sequence is below:
step1: irq handler for host2 removed ->
step2: irq handler for host1 removed and irq disabled ->
... system suspended ...
... system resumed ...
step3: irq enabled and the irq handler for host1 restored ->
step4: irq handler for host2 restored
3. So there is the buggy time slot that the irq is enabled but the irq
handler for host2 is removed. Then host2 interrupt can be triggered
but can't be handled at that moment.
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Stephen Warren [Thu, 3 Jan 2013 05:34:49 +0000 (22:34 -0700)]
mmc: add BCM2835 driver
Add a very simple driver for the BCM2835 SoC, which is used in the
Raspberry Pi board.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Konstantin Dorfman [Mon, 14 Jan 2013 19:28:17 +0000 (14:28 -0500)]
mmc: fix async request mechanism for sequential read scenarios
When current request is running on the bus and if next request fetched
by mmcqd is NULL, mmc context (mmcqd thread) gets blocked until the
current request completes. This means that if new request comes in while
the mmcqd thread is blocked, this new request can not be prepared in
parallel to current ongoing request. This may result in delaying the new
request execution and increase it's latency.
This change allows to wake up the MMC thread on new request arrival.
Now once the MMC thread is woken up, a new request can be fetched and
prepared in parallel to the current running request which means this new
request can be started immediately after the current running request
completes.
With this change read throughput is improved by 16%.
Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Reviewed-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Wed, 26 Dec 2012 01:40:17 +0000 (10:40 +0900)]
mmc: queue: exclude asynchronous transfer for special request
Unlike normal r/w request, special requests(discard, flush)
is finished with a one-time issue_fn. Request change to
mqrq_prev makes unnecessary call.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Guennadi Liakhovetski [Wed, 12 Dec 2012 14:45:14 +0000 (15:45 +0100)]
mmc: sh_mmcif: simplify IRQ processing
The classical way to process IRQs is read out the status, ack all triggered
IRQs, possibly mask them, then process them. Follow this simple procesure
instead of the current complex custom algorithm.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Teppei Kamijou [Wed, 12 Dec 2012 14:38:18 +0000 (15:38 +0100)]
mmc: sh_mmcif: report all errors
Make error reporting in the driver more verbose. This patch is based on
an earlier work by Teppei Kamijou, but we try to not add any new error
messages to the log in the normal case to avoid confusing the user, and
also add a few more dev_dbg() calls.
Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
[g.liakhovetski@gmx.de: avoid producing new errors in normal case]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Guennadi Liakhovetski [Wed, 12 Dec 2012 14:38:17 +0000 (15:38 +0100)]
mmc: sh_mmcif: fix I/O errors
The INT_BUFWEN IRQ often arrives with other bits set too. If they are not
cleared, an additional IRQ can be triggered, sometimes also after the MMC
request has already been completed. This leads to block I/O errors. Earlier
Teppei Kamijou also observed these additional interrupts and proposed to
explicitly wait for them. This patch chooses an alternative approach of
clearing all active bits immediately, when processing the main interrupt.
Reported-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Guennadi Liakhovetski [Wed, 12 Dec 2012 14:38:16 +0000 (15:38 +0100)]
mmc: sh_mmcif: reset DMA completion immediately before starting DMA
DMA completion can be signalled from the DMA callback and from the error
handler. If both are called, the completion struct can enter an
inconsistent state. To prevent this move completion initialisation
immediately before activating DMA.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Guennadi Liakhovetski [Wed, 12 Dec 2012 14:38:15 +0000 (15:38 +0100)]
mmc: sh_mmcif: reset error code for any opcode
If a command execution has produced an error, it has to be reset as a part
of the error handling.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Guennadi Liakhovetski [Wed, 12 Dec 2012 14:38:14 +0000 (15:38 +0100)]
mmc: sh_mmcif: fix a race, causing an Oops on SMP
Oopses have been observed on SMP in the sh-mmcif IRQ thread, when the two
IRQ threads run simultaneously on two CPUs. Also take care to guard the
timeout work and the DMA completion callback from possible NULL-pointer
dereferences and races.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Guennadi Liakhovetski [Wed, 12 Dec 2012 14:38:13 +0000 (15:38 +0100)]
mmc: sh_mmcif: (cosmetic) simplify boolean return blocks
Use "return condition" instead of "if (condition) return true; return false"
in functions, returning bool.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Teppei Kamijou [Wed, 12 Dec 2012 14:38:12 +0000 (15:38 +0100)]
mmc: sh_mmcif: Terminate DMA transactions when detecting timeout or error
If a DMA transaction fails, terminate all outstanding DMA transfers and
unmap buffers.
Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
[g.liakhovetski@gmx.de: forward-port, add dma_unmap_sg() in error cases]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Guennadi Liakhovetski [Wed, 12 Dec 2012 14:38:11 +0000 (15:38 +0100)]
mmc: sh_mmcif: fix missing and consolidate IO completion timeouts
Read block and write block operations are currently missing completion
timeouts. Add missing timeouts and consolidate them at one location.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Teppei Kamijou [Wed, 12 Dec 2012 14:38:10 +0000 (15:38 +0100)]
mmc: sh_mmcif: Avoid unnecessary mmc_delay() at mmc_card_sleepawake()
SH/R-Mobile MMCIF host controller can wait while the card signals busy.
Set MMC_CAP_WAIT_WHILE_BUSY to inform an upper layer (core/mmc_ops.c)
not to insert unnecessary mmc_delay().
Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Teppei Kamijou [Wed, 12 Dec 2012 14:38:09 +0000 (15:38 +0100)]
mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout
Timeout period should be properly normalized using msecs_to_jiffies().
Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Teppei Kamijou [Wed, 12 Dec 2012 14:38:08 +0000 (15:38 +0100)]
mmc: sh_mmcif: Add support for eMMC Dual Data Rate
Some MMCIF implementations support the Dual Data Rate. With this patch,
platforms can set the MMC_CAP_UHS_DDR50 capability flag in MMCIF platform
data. This will let the MMC core to actually use the DDR mode.
Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Shinya Kuribayashi [Mon, 14 Jan 2013 19:12:36 +0000 (14:12 -0500)]
mmc: sh_mmcif: add support for bundled MMCIF IRQs
On newer SoCs like R-Mobile U2, MMCIF interrupts are bundled.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Teppei Kamijou [Wed, 12 Dec 2012 14:38:06 +0000 (15:38 +0100)]
mmc: sh_mmcif: ensure run-time suspend call is processed before suspend
With this post-v2.6.35 change applied:
commit
a0a1a5fd4fb15ec61117c759fe9f5c16c53d9e9c
Author: Tejun Heo <tj@kernel.org>
Date: Tue Jun 29 10:07:12 2010 +0200
workqueue: reimplement workqueue freeze using max_active
freeze_workqueues_begin() was introduced and workqueue now gets frozen
before device drivers suspend operations.
We have to ensure that run-time PM suspend operation completes before
system-wide suspend is started.
Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Teppei Kamijou [Wed, 12 Dec 2012 14:38:05 +0000 (15:38 +0100)]
mmc: sh_mmcif: force to fail CMD52 immediately
mmc_rescan() sends CMD52 (SD_IO_RW_DIRECT) to reset SDIO card during
card detection. CMD52 should be ignored by SD/eMMC cards, but we can
also abort it in the driver immediately, since MMCIF doesn't support
SDIO cards anyway.
Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Shawn Guo [Tue, 11 Dec 2012 14:32:20 +0000 (22:32 +0800)]
mmc: sdhci-esdhc-imx: use slot-gpio helpers for CD and WP
Use slot-gpio helpers to save some code in the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Shawn Guo [Tue, 11 Dec 2012 14:32:19 +0000 (22:32 +0800)]
mmc: remove unncessary mmc_gpio_free_cd() call from slot-gpio users
Since slot-gpio uses devm_* managed functions in mmc_gpio_request_cd()
now, we can remove those mmc_gpio_free_cd() call from host drivers'
.probe() error path and .remove().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Shawn Guo [Tue, 11 Dec 2012 14:32:18 +0000 (22:32 +0800)]
mmc: slot-gpio: use devm_* managed functions to ease users
Use devm_* managed functions, so that slot-gpio users do not have to
call mmc_gpio_free_ro/cd to free up resources requested in
mmc_gpio_request_ro/cd.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Shawn Guo [Tue, 11 Dec 2012 07:23:42 +0000 (15:23 +0800)]
mmc: sdhci: query card presence from cd-gpio before asking SDHCI
Call mmc_gpio_get_cd() to query card presence from cd-gpio before
asking SDHCI. The rationale behind this change is that flag
SDHCI_QUIRK_BROKEN_CARD_DETECTION is designed for SDHCI controller to
tell that SDHCI_PRESENT_STATE is broken, and it should be used for this
case only. So when cd-gpio is being used, the controller should set
the flag to tell that SDHCI_PRESENT_STATE is not available.
However, the existing code will skip checking cd-gpio as long as flag
SDHCI_QUIRK_BROKEN_CARD_DETECTION is set. Change the querying order
between cd-gpio and SDHCI to support the rationale above.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Subhash Jadavani [Tue, 4 Dec 2012 11:36:20 +0000 (17:06 +0530)]
mmc: sdio: print correct UHS mode during card detection
When SDIO3.0 card is detected, incorrect bus speed mode
is printed as part of card detection print in kernel logs.
This change fixes it so that user won't be confused by
looking at incorrect card detection message in logs.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Jackey Shen <Jackey.Shen@amd.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Sujit Reddy Thumma [Tue, 4 Dec 2012 11:36:19 +0000 (17:06 +0530)]
mmc: sdio: Fix SDIO 3.0 UHS-I initialization sequence
According to UHS-I initialization sequence for SDIO 3.0 cards,
the host must set bit[24] (S18R) of OCR register during OCR
handshake to know whether the SDIO card is capable of doing
1.8V I/O.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Johan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Subhash Jadavani [Tue, 4 Dec 2012 11:36:18 +0000 (17:06 +0530)]
mmc: sdio: fix resume failure due to lack of CMD52 reset
If SDIO keep power flag (MMC_PM_KEEP_POWER) is not set, card would
be reinitialized during resume but as we are not resetting
(CMD52 reset) the SDIO card during this reinitialization, card may
fail to respond back to subsequent commands (CMD5 etc...).
This change resets the card before the reinitialization of card
during resume.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
YOSHIFUJI Hideaki [Fri, 25 Jan 2013 14:54:20 +0000 (16:54 +0200)]
digsig: Fix memory leakage in digsig_verify_rsa()
digsig_verify_rsa() does not free kmalloc'ed buffer returned by
mpi_get_buffer().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Morris <james.l.morris@oracle.com>
Linus Torvalds [Fri, 1 Feb 2013 01:08:14 +0000 (12:08 +1100)]
Linux 3.8-rc6
Linus Torvalds [Fri, 1 Feb 2013 01:04:22 +0000 (12:04 +1100)]
Merge tag 'dm-3.8-fixes-2' of git://git./linux/kernel/git/agk/linux-dm
Pull more device-mapper fixes from Alasdair G Kergon:
"A fix for stacked dm thin devices and a fix for the new dm WRITE SAME
support."
* tag 'dm-3.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm: fix write same requests counting
dm thin: fix queue limits stacking
Linus Torvalds [Thu, 31 Jan 2013 21:44:59 +0000 (08:44 +1100)]
Merge branch 'for-3.8/upstream-fixes' of git://git./linux/kernel/git/jikos/hid
PullHID fixes from Jiri Kosina:
- fix i2c-hid and hidraw interaction, by Benjamin Tissoires
- a quirk to make a particular device (Formosa IR receiver) work
properly, by Nicholas Santos
* 'for-3.8/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: i2c-hid: fix i2c_hid_output_raw_report
HID: usbhid: quirk for Formosa IR receiver
HID: remove x bit from sensor doc
Linus Torvalds [Thu, 31 Jan 2013 21:43:52 +0000 (08:43 +1100)]
Merge tag 'nfs-for-3.8-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Error reporting in nfs_xdev_mount incorrectly maps all errors to
ENOMEM
- Fix an NFSv4 refcounting issue
- Fix a mount failure when the server reboots during NFSv4 trunking
discovery
- NFSv4.1 mounts may need to run the lease recovery thread.
- Don't silently fail setattr() requests on mountpoints
- Fix a SUNRPC socket/transport livelock and priority queue issue
- We must handle NFS4ERR_DELAY when resetting the NFSv4.1 session.
* tag 'nfs-for-3.8-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4.1: Handle NFS4ERR_DELAY when resetting the NFSv4.1 session
SUNRPC: When changing the queue priority, ensure that we change the owner
NFS: Don't silently fail setattr() requests on mountpoints
NFSv4.1: Ensure that nfs41_walk_client_list() does start lease recovery
NFSv4: Fix NFSv4 trunking discovery
NFSv4: Fix NFSv4 reference counting for trunked sessions
NFS: Fix error reporting in nfs_xdev_mount
Linus Torvalds [Thu, 31 Jan 2013 21:43:04 +0000 (08:43 +1100)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"A number of fixes all across the MIPS tree. No area is particularly
standing out and things have cooled down quite nicely for a release."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Function tracer: Fix broken function tracing
mips: Move __virt_addr_valid() to a place for MIPS 64
MIPS: Netlogic: Fix UP compilation on XLR
MIPS: AR71xx: Fix AR71XX_PCI_MEM_SIZE
MIPS: AR724x: Fix AR724X_PCI_MEM_SIZE
MIPS: Lantiq: Fix cp0_perfcount_irq mapping
MIPS: DSP: Fix DSP mask for registers.
MIPS: Fix build failure by adding definition of pfn_pmd().
MIPS: Octeon: Fix warning.
MIPS: delay.c: Check BITS_PER_LONG instead of __SIZEOF_LONG__
MIPS: PNX833x: Fix comment.
MIPS: Add struct p_format to union mips_instruction.
MIPS: Export <asm/break.h>.
MIPS: BCM47xx: Enable SSB prerequisite SSB_DRIVER_PCICORE.
MIPS: BCM47xx: Select GPIOLIB for BCMA on bcm47xx platform
MIPS: vpe.c: Fix null pointer dereference in print arguments.
Jason Cooper [Thu, 31 Jan 2013 17:39:01 +0000 (17:39 +0000)]
Merge commit '
d293875' into mvebu/boards
Pulled in mmc/mmc-next up to:
d293875 mmc: mvsdio: add pinctrl integration
Jason Cooper [Thu, 31 Jan 2013 17:38:48 +0000 (17:38 +0000)]
Merge tag 'tags/drivers_for_v3.9' into mvebu/boards
mvebu drivers for v3.9
- use rtc-mv in mvebu armv7 SoCs
- add pci-e hotplug for kirkwood
Depends on:
- tags/mvebu_fixes_for_v3.8-rc6
Jason Cooper [Thu, 31 Jan 2013 17:38:38 +0000 (17:38 +0000)]
Merge tag 'tags/cleanup_for_v3.9_round2' into mvebu/boards
cleanup for v3.9 round2
- remove unneeded #includes for mach-dove
- remove unneeded #includes and code for the nsa310
Jason Cooper [Thu, 31 Jan 2013 17:38:25 +0000 (17:38 +0000)]
Merge tag 'tags/mvebu_fixes_for_v3.8-rc6' into mvebu/boards
fixes for v3.8-rc6
- add missing gpio interrupt lines to dove dt
- fix bad logic for printing MPP error message on orion boards
- build proper serial port driver after changing mvebu DT compatible property
- This is a change to mvebu_defconfig that I wouldn't usually push out as a
fix. However, the commit
b24212f arm: mvebu: Use dw-apb-uart instead of ns16650 as UART driver
changed the serial driver for the board in the dts file. without the patch
I've included in this pull, users won't see any log messages.
Andrew Lunn [Wed, 9 Jan 2013 12:22:15 +0000 (13:22 +0100)]
cpuidle: kirkwood: Move out of mach directory
Move the Kirkwood cpuidle driver out of arch/arm/mach-kirkwood and
into drivers/cpuidle. Convert the driver into a platform driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Benjamin Tissoires [Thu, 31 Jan 2013 16:50:02 +0000 (17:50 +0100)]
HID: i2c-hid: fix i2c_hid_output_raw_report
i2c_hid_output_raw_report is used by hidraw to forward set_report requests.
The current implementation of i2c_hid_set_report needs to take the
report_id as an argument. The report_id is stored in the first byte
of the buffer in argument of i2c_hid_output_raw_report.
Not removing the report_id from the given buffer adds this byte 2 times
in the command, leading to a non working command.
Reported-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Al Cooper [Wed, 16 Jan 2013 22:43:28 +0000 (22:43 +0000)]
MIPS: Function tracer: Fix broken function tracing
Function tracing is currently broken for all 32 bit MIPS platforms.
When tracing is enabled, the kernel immediately hangs on boot.
This is a result of commit
b732d439cb43336cd6d7e804ecb2c81193ef63b0
that changes the kernel/trace/Kconfig file so that is no longer
forces FRAME_POINTER when FUNCTION_TRACING is enabled.
MIPS frame pointers are generally considered to be useless because
they cannot be used to unwind the stack. Unfortunately the MIPS
function tracing code has bugs that are masked by the use of frame
pointers. This commit fixes the bugs so that MIPS frame pointers
don't need to be enabled.
The bugs are a result of the odd calling sequence used to call the trace
routine. This calling sequence is inserted into every traceable function
when the tracing CONFIG option is enabled. This sequence is generated
for 32bit MIPS platforms by the compiler via the "-pg" flag.
Part of the sequence is "addiu sp,sp,-8" in the delay slot after every
call to the trace routine "_mcount" (some legacy thing where 2 arguments
used to be pushed on the stack). The _mcount routine is expected to
adjust the sp by +8 before returning. So when not disabled, the original
jalr and addiu will be there, so _mcount has to adjust sp.
The problem is that when tracing is disabled for a function, the
"jalr _mcount" instruction is replaced with a nop, but the
"addiu sp,sp,-8" is still executed and the stack pointer is left
trashed. When frame pointers are enabled the problem is masked
because any access to the stack is done through the frame
pointer and the stack pointer is restored from the frame pointer when
the function returns.
This patch writes two nops starting at the address of the "jalr _mcount"
instruction whenever tracing is disabled. This means that the
"addiu sp,sp.-8" will be converted to a nop along with the "jalr". When
disabled, there will be two nops.
This is SMP safe because the first time this happens is during
ftrace_init() which is before any other processor has been started.
Subsequent calls to enable/disable tracing when other CPUs ARE running
will still be safe because the enable will only change the first nop
to a "jalr" and the disable, while writing 2 nops, will only be changing
the "jalr". This patch also stops using stop_machine() to call the
tracer enable/disable routines and calls them directly because the
routines are SMP safe.
When the kernel first boots we have to be able to handle the gcc
generated jalr, addui sequence until ftrace_init gets a chance to run
and change the sequence. At this point mcount just adjusts the stack
and returns. When ftrace_init runs, we convert the jalr/addui to nops.
Then whenever tracing is enabled we convert the first nop to a "jalr
mcount+8". The mcount+8 entry point skips the stack adjust.
[ralf@linux-mips.org: Folded in Steven Rostedt's build fix.]
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: rostedt@goodmis.org
Cc: ddaney.cavm@gmail.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4806/
Patchwork: https://patchwork.linux-mips.org/patch/4841/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Alasdair G Kergon [Thu, 31 Jan 2013 14:23:36 +0000 (14:23 +0000)]
dm: fix write same requests counting
When processing write same requests, fix dm to send the configured
number of WRITE SAME requests to the target rather than the number of
discards, which is not always the same.
Device-mapper WRITE SAME support was introduced by commit
23508a96cd2e857d57044a2ed7d305f2d9daf441 ("dm: add WRITE SAME support").
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Sebastian Hesselbarth [Tue, 29 Jan 2013 21:23:09 +0000 (22:23 +0100)]
ARM: dove: cleanup includes
This patch cleans unneccessary includes and reorders the remaining
includes in common dove code.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Jason Cooper [Wed, 23 Jan 2013 19:58:21 +0000 (19:58 +0000)]
ARM: kirkwood: nsa310: cleanup includes and unneeded code
After removing the unneeded linux/i2c.h, linux/of.h was needed for
of_machine_is_compatible(). i2c.h had included of.h.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Steven Rostedt [Fri, 25 Jan 2013 17:13:15 +0000 (17:13 +0000)]
mips: Move __virt_addr_valid() to a place for MIPS 64
Commit
d3ce88431892 "MIPS: Fix modpost error in modules attepting to use
virt_addr_valid()" moved __virt_addr_valid() from a macro in a header
file to a function in ioremap.c. But ioremap.c is only compiled for MIPS
32, and not for MIPS 64.
When compiling for my yeeloong2, which supposedly supports hibernation,
which compiles kernel/power/snapshot.c which calls virt_addr_valid(), I
got this error:
LD init/built-in.o
kernel/built-in.o: In function `memory_bm_free':
snapshot.c:(.text+0x4c9c4): undefined reference to `__virt_addr_valid'
snapshot.c:(.text+0x4ca58): undefined reference to `__virt_addr_valid'
kernel/built-in.o: In function `snapshot_write_next':
(.text+0x4e44c): undefined reference to `__virt_addr_valid'
kernel/built-in.o: In function `snapshot_write_next':
(.text+0x4e890): undefined reference to `__virt_addr_valid'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2
I suspect that __virt_addr_valid() is fine for mips 64. I moved it to
mmap.c such that it gets compiled for mips 64 and 32.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4842/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Mike Snitzer [Thu, 31 Jan 2013 14:11:14 +0000 (14:11 +0000)]
dm thin: fix queue limits stacking
thin_io_hints() is blindly copying the queue limits from the thin-pool
which can lead to incorrect limits being set. The fix here simply
deletes the thin_io_hints() hook which leaves the existing stacking
infrastructure to set the limits correctly.
When a thin-pool uses an MD device for the data device a thin device
from the thin-pool must respect MD's constraints about disallowing a bio
from spanning multiple chunks. Otherwise we can see problems. If the raid0
chunksize is 1152K and thin-pool chunksize is 256K I see the following
md/raid0 error (with extra debug tracing added to thin_endio) when
mkfs.xfs is executed against the thin device:
md/raid0:md99: make_request bug: can't convert block across chunks or bigger than 1152k 6688 127
device-mapper: thin: bio sector=2080 err=-5 bi_size=130560 bi_rw=17 bi_vcnt=32 bi_idx=0
This extra DM debugging shows that the failing bio is spanning across
the first and second logical 1152K chunk (sector 2080 + 255 takes the
bio beyond the first chunk's boundary of sector 2304). So the bio
splitting that DM is doing clearly isn't respecting the MD limits.
max_hw_sectors_kb is 127 for both the thin-pool and thin device
(queue_max_hw_sectors returns 255 so we'll excuse sysfs's lack of
precision). So this explains why bi_size is 130560.
But the thin device's max_hw_sectors_kb should be 4 (PAGE_SIZE) given
that it doesn't have a .merge function (for bio_add_page to consult
indirectly via dm_merge_bvec) yet the thin-pool does sit above an MD
device that has a compulsory merge_bvec_fn. This scenario is exactly
why DM must resort to sending single PAGE_SIZE bios to the underlying
layer. Some additional context for this is available in the header for
commit
8cbeb67a ("dm: avoid unsupported spanning of md stripe boundaries").
Long story short, the reason a thin device doesn't properly get
configured to have a max_hw_sectors_kb of 4 (PAGE_SIZE) is that
thin_io_hints() is blindly copying the queue limits from the thin-pool
device directly to the thin device's queue limits.
Fix this by eliminating thin_io_hints. Doing so is safe because the
block layer's queue limits stacking already enables the upper level thin
device to inherit the thin-pool device's discard and minimum_io_size and
optimal_io_size limits that get set in pool_io_hints. But avoiding the
queue limits copy allows the thin and thin-pool limits to be different
where it is important, namely max_hw_sectors_kb.
Reported-by: Daniel Browning <db@kavod.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Linus Torvalds [Thu, 31 Jan 2013 06:10:36 +0000 (17:10 +1100)]
Merge branch 'x86-efi-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 EFI fixes from Peter Anvin:
"This is a collection of fixes for the EFI support. The controversial
bit here is a set of patches which bumps the boot protocol version as
part of fixing some serious problems with the EFI handover protocol,
used when booting under EFI using a bootloader as opposed to directly
from EFI. These changes should also make it a lot saner to support
cross-mode 32/64-bit EFI booting in the future. Getting these changes
into 3.8 means we avoid presenting an inconsistent ABI to bootloaders.
Other changes are display detection and fixing efivarfs."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: remove attribute check from setup_efi_pci
x86, build: Dynamically find entry points in compressed startup code
x86, efi: Fix PCI ROM handing in EFI boot stub, in 32-bit mode
x86, efi: Fix 32-bit EFI handover protocol entry point
x86, efi: Fix display detection in EFI boot stub
x86, boot: Define the 2.12 bzImage boot protocol
x86/boot: Fix minor fd leakage in tools/relocs.c
x86, efi: Set runtime_version to the EFI spec revision
x86, efi: fix 32-bit warnings in setup_efi_pci()
efivarfs: Delete dentry from dcache in efivarfs_file_write()
efivarfs: Never return ENOENT from firmware
efi, x86: Pass a proper identity mapping in efi_call_phys_prelog
efivarfs: Drop link count of the right inode
Linus Torvalds [Thu, 31 Jan 2013 06:08:43 +0000 (17:08 +1100)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"This is a collection of miscellaneous fixes, the most important one is
the fix for the Samsung laptop bricking issue (auto-blacklisting the
samsung-laptop driver); the efi_enabled() changes you see below are
prerequisites for that fix.
The other issues fixed are booting on OLPC XO-1.5, an UV fix, NMI
debugging, and requiring CAP_SYS_RAWIO for MSR references, just as
with I/O port references."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
samsung-laptop: Disable on EFI hardware
efi: Make 'efi_enabled' a function to query EFI facilities
smp: Fix SMP function call empty cpu mask race
x86/msr: Add capabilities check
x86/dma-debug: Bump PREALLOC_DMA_DEBUG_ENTRIES
x86/olpc: Fix olpc-xo1-sci.c build errors
arch/x86/platform/uv: Fix incorrect tlb flush all issue
x86-64: Fix unwind annotations in recent NMI changes
x86-32: Start out cr0 clean, disable paging before modifying cr3/4
Linus Torvalds [Thu, 31 Jan 2013 06:04:46 +0000 (17:04 +1100)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull console lockdep checking revert from Dave Airlie.
The lockdep splat this showed was interesting, but it's very very old,
and we won't be fixing it until 3.9. In the meantime, undo the lockdep
annotation so that we don't generate the (known) console lockdep issue,
and then possibly hide any potential other (unknown) lockdep problems
that got disabled by the first one that triggered.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "console: implement lockdep support for console_lock"