OSDN Git Service
Akash Goel [Fri, 22 Apr 2016 18:35:45 +0000 (00:05 +0530)]
drm/i915/bxt: Explicitly clear the Turbo control register
As a part of WaGsvDisableTurbo, Driver makes an early exit from the
Gen9 Turbo enabling function, so doesn't program the Turbo Control register.
But BIOS could leave the Hw Turbo as enabled, so need to explicitly clear
out the Control register just to avoid inconsitency with debugfs
interface, which will show Turbo as enabled only and that is not expected
after adding the WaGsvDisableTurbo. Apart from this there is no problem
even if the Turbo is left enabled in the Control register, as the Up/Down
interrupts would remain masked.
v2: Add explicit clearing of Turbo Control register to *_disable_rps()
also for the similar consistency (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-2-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Akash Goel [Fri, 22 Apr 2016 18:35:46 +0000 (00:05 +0530)]
drm/i915: Correct the i915_frequency_info debugfs output
There are certain registers, which captures the time elapsed in the
in current Up/Down EI, for how long GT has been Idle/Busy/Avg in the
current Up/Down EI and also in the previous Up/Down EI.
These register values are reported by the i915_frequency_info debugfs
interface. The Driver prints the 'us' suffix after the values, albeit
they are actually in raw form & not in microsecond units.
This patch removes the 'us' suffix so that its clear to User that values
are indeed in raw form.
v2: Present the values in microseconds unit also, after platform
specific conversion (Chris)
v3: Add a space between raw & microsecond value (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-3-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Akash Goel [Fri, 22 Apr 2016 18:35:44 +0000 (00:05 +0530)]
drm/i915: Macros to convert PM time interval values to microseconds
Added a new GT_PM_INTERVAL_TO_US macro to perform the platform
specific conversion of PM time interval values to microseconds unit.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-1-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Wed, 20 Apr 2016 13:43:56 +0000 (16:43 +0300)]
drm/i915: Make RPS EI/thresholds multiple of 25 on SNB-BDW
Somehow my SNB GT1 (Dell XPS 8300) gets very unhappy around
GPU hangs if the RPS EI/thresholds aren't suitably aligned.
It seems like scheduling/timer interupts stop working somehow
and things get stuck eg. in usleep_range().
I bisected the problem down to
commit
8a5864377b12 ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
I observed that before all the values were at least multiples of 25,
but afterwards they are not. And rounding things up to the next multiple
of 25 does seem to help, so lets' do that. I also tried roundup(..., 5)
but that wasn't sufficient. Also I have no idea if we might need this sort of
thing on gen9+ as well.
These are the original EI/thresholds:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10250
GEN6_RP_UP_THRESHOLD 9225
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 8000
GEN6_RP_UP_THRESHOLD 6800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
These are after
8a5864377b12:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10156
GEN6_RP_UP_THRESHOLD 9140
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7812
GEN6_RP_UP_THRESHOLD 6640
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
And these are what we have after this patch:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10175
GEN6_RP_UP_THRESHOLD 9150
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7825
GEN6_RP_UP_THRESHOLD 6650
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
Cc: stable@vger.kernel.org
Cc: Akash Goel <akash.goel@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Testcase: igt/kms_pipe_crc_basic/hang-read-crc-pipe-B
Fixes:
8a5864377b12 ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461159836-9108-1-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Shashank Sharma [Thu, 21 Apr 2016 11:18:32 +0000 (16:48 +0530)]
drm/i915: Fake HDMI live status
This patch does the following:
- Fakes live status of HDMI as connected (even if that's not).
While testing certain (monitor + cable) combinations with
various intel platforms, it seems that live status register
doesn't work reliably on some older devices. So limit the
live_status check for HDMI detection, only for platforms
from gen7 onwards.
V2: restrict faking live_status to certain platforms
V3: (Ville)
- keep the debug message for !live_status case
- fix indentation of comment
- remove "warning" from the debug message
(Jani)
- Change format of fix details in the commit message
Fixes:
237ed86c693d ("drm/i915: Check live status before reading edid")
Cc: stable@vger.kernel.org # v4.4
Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461237606-16491-1-git-send-email-shashank.sharma@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Imre Deak [Wed, 20 Apr 2016 17:46:06 +0000 (20:46 +0300)]
drm/i915/bxt: Force reprogramming a PHY with invalid HW state
It's possible that BIOS enables PHY0, but it programmes only the first
channel on it. Since we program the PHYs only during driver loading this
is an incorrect configuration from the driver's point of view, since we
may use both channels eventually. Detect this scenario and force
reprogramming the PHY in this case.
The actual scenario for me was that the lane optimization for the second
channel in PHY0 was not setup by BIOS and so a state verification
warning was triggered. Everything else was setup properly.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461174366-16758-4-git-send-email-imre.deak@intel.com
Imre Deak [Thu, 21 Apr 2016 16:19:21 +0000 (19:19 +0300)]
drm/i915/bxt: Wait for PHY1 GRC done if PHY0 was already enabled
If we skipped PHY0 initialization because it was already enabled by
BIOS, we still have to wait for the PHY1 GRC calibration as that is
done as part of the PHY0 init.
v2:
- Use the actual PHY index in the debug message in
broxton_phy_wait_grc_done() (Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461255561-1644-1-git-send-email-imre.deak@intel.com
Imre Deak [Wed, 20 Apr 2016 17:46:04 +0000 (20:46 +0300)]
drm/i915/bxt: Use PHY0 GRC value for HW state verification
It's possible that BIOS enables PHY1 only to read out the GRC value from
it to be used in PHY0 and then disables PHY1. In this case we can't use
the PHY1 GRC value for state verification, so use instead the one in PHY0
always.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461174366-16758-2-git-send-email-imre.deak@intel.com
Matthew Auld [Fri, 22 Apr 2016 11:09:25 +0000 (12:09 +0100)]
drm/i915: use dev_priv directly in gen8_ppgtt_notify_vgt
Remove dev local and use to_i915() in gen8_ppgtt_notify_vgt.
v2: use dev_priv directly for QUESTION_MACROS (Joonas Lahtinen)
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461323365-21256-1-git-send-email-matthew.auld@intel.com
Imre Deak [Wed, 20 Apr 2016 17:27:57 +0000 (20:27 +0300)]
drm/i915/bxt: Enable DC5 during runtime resume
Right after runtime resume we know that we can re-enable DC5, since we
just disabled DC9 and power well 2 is disabled. So enable DC5 explicitly
instead of delaying this until the next time we disable power well 2.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-5-git-send-email-imre.deak@intel.com
Imre Deak [Wed, 20 Apr 2016 17:27:56 +0000 (20:27 +0300)]
drm/i915/bxt: Sanitize DC state tracking during system resume
After suspend-to-ram or -disk we don't know what power state the display
HW will be, DC0 or DC9 are both possible states, so reset the software
DC state tracking in these cases. This gets rid of 'DC state mismatch'
error messages during resuming from ram or disk where we expected to be
in DC9 (as set by the suspend handler) but we are in DC0.
v2:
- Remove extra WS in gen9_sanitize_dc_state() (Bob)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-4-git-send-email-imre.deak@intel.com
Imre Deak [Wed, 20 Apr 2016 17:27:55 +0000 (20:27 +0300)]
drm/i915/bxt: Don't uninit/init display core twice during system suspend/resume
Atm, we run the BSpec display core uninit/init sequences twice during
system suspend/resume. While this shouldn't cause any problem, it's
redundant, so get rid of the duplicate call.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-3-git-send-email-imre.deak@intel.com
Imre Deak [Wed, 20 Apr 2016 17:27:54 +0000 (20:27 +0300)]
drm/i915: Inline intel_suspend_complete
Initially we thought that the platform specific suspend/resume sequences
can be shared between the runtime and system suspend/resume handlers.
This turned out to be not true, we have quite a few differences on most
of the platforms. This was realized already earlier by Paulo who
inlined the platform specific resume_prepare handlers. We have the
same problem with the corresponding suspend_complete handlers, there are
platform differences that make it unfeasible to share the code between
the runtime and system suspend paths. Also now we call functions that
need to be paired like hsw_enable_pc8()/hsw_disable_pc8() from different
levels of the call stack, which is confusing. Fix this by inlining the
suspend_complete handlers too.
This is also needed by the next patch that removes a redundant
uninit/init call during system suspend/resume on BXT.
No functional change.
CC: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
[s/uninline/inline in the commit message]
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-2-git-send-email-imre.deak@intel.com
Imre Deak [Tue, 19 Apr 2016 10:00:36 +0000 (13:00 +0300)]
drm/i915/kbl: Don't WARN for expected secondary MISC IO power well request
In commit
5f304c873634 ("drm/i915/kbl: Reset secondary power well requests
left on by DMC/KVMR") I forgot about the fact that SKL==KBL most of the
time and that a secondary MISC IO power well request left on by the DMC is
"expected". Tune down the corresponding WARN to be a debug message. This
was caught by CI suspend tests.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461060036-19043-1-git-send-email-imre.deak@intel.com
Mika Kahola [Wed, 20 Apr 2016 12:39:02 +0000 (15:39 +0300)]
drm/i915: Fix eDP low vswing for Broadwell
It was noticed on bug #94087 that module parameter
i915.edp_vswing=2 that should override the VBT setting
to use default voltage swing (400 mV) was not applied
for Broadwell.
This patch provides a fix for this by checking if default
i.e. higher voltage swing is requested to be used and
applies the DDI translations table for DP instead of eDP
(low vswing) table.
v2: Combine two if statements into one (Jani)
v3: Change dev_priv->edp_low_vswing to use dev_priv->vbt.edp.low_vswing
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94087
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461155942-7749-1-git-send-email-mika.kahola@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Dave Gordon [Tue, 12 Apr 2016 13:46:16 +0000 (14:46 +0100)]
drm/i915: check for ERR_PTR from i915_gem_object_pin_map()
The newly-introduced function i915_gem_object_pin_map() returns an
ERR_PTR (not NULL) if the pin-and-map opertaion fails, so that's what we
must check for. And it's nicer not to assign such a pointer-or-error to
a structure being filled in until after it's been validated, so we
should keep it local and avoid exporting a bogus pointer. Also, for
clarity and symmetry, we should clear 'virtual_start' along with 'vma'
when unmapping a ringbuffer.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Dave Gordon [Tue, 19 Apr 2016 15:08:36 +0000 (16:08 +0100)]
drm/i915/guc: local optimisations and updating comments
Tidying up guc_init_proc_desc() and adding commentary to the client
structure after the recent change in GuC page mapping strategy.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461078516-28678-1-git-send-email-david.s.gordon@intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Alex Dai [Tue, 19 Apr 2016 15:08:35 +0000 (16:08 +0100)]
drm/i915/guc: drop cached copy of 'wq_head'
Now that we keep the GuC client process descriptor permanently mapped,
we don't really need to keep a local copy of the GuC's work-queue-head.
So we can simplify the code a little by not doing this.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Dave Gordon [Tue, 19 Apr 2016 15:08:34 +0000 (16:08 +0100)]
drm/i915/guc: keep GuC doorbell & process descriptor mapped in kernel
Don't use kmap_atomic() for doorbell & process descriptor access.
This patch fixes the BUG shown below, where the thread could sleep
while holding a kmap_atomic mapping. In order not to need to call
kmap_atomic() in this code path, we now set up a permanent kernel
mapping of the shared doorbell and process-descriptor page, and
use that in all doorbell and process-descriptor related code.
BUG: scheduling while atomic: gem_close_race/1941/0x00000002
Modules linked in: hid_generic usbhid i915 asix usbnet libphy mii
i2c_algo_bit drm_kms_helper cfbfillrect syscopyarea cfbimgblt
sysfillrect sysimgblt fb_sys_fops cfbcopyarea drm coretemp i2c_hid
hid video pinctrl_sunrisepoint pinctrl_intel acpi_pad nls_iso8859_1
e1000e ptp psmouse pps_core ahci libahci
CPU: 0 PID: 1941 Comm: gem_close_race Tainted: G U 4.4.0-160121+ #123
Hardware name: Intel Corporation Skylake Client platform/Skylake AIO
DDR3L RVP10, BIOS SKLSE2R1.R00.X100.B01.
1509220551 09/22/2015
0000000000013e40 ffff880166c27a78 ffffffff81280d02 ffff880172c13e40
ffff880166c27a88 ffffffff810c203a ffff880166c27ac8 ffffffff814ec808
ffff88016b7c6000 ffff880166c28000 00000000000f4240 0000000000000001
Call Trace:
[<
ffffffff81280d02>] dump_stack+0x4b/0x79
[<
ffffffff810c203a>] __schedule_bug+0x41/0x4f
[<
ffffffff814ec808>] __schedule+0x5a8/0x690
[<
ffffffff814ec927>] schedule+0x37/0x80
[<
ffffffff814ef3fd>] schedule_hrtimeout_range_clock+0xad/0x130
[<
ffffffff81090be0>] ? hrtimer_init+0x10/0x10
[<
ffffffff814ef3f1>] ? schedule_hrtimeout_range_clock+0xa1/0x130
[<
ffffffff814ef48e>] schedule_hrtimeout_range+0xe/0x10
[<
ffffffff814eef9b>] usleep_range+0x3b/0x40
[<
ffffffffa01ec109>] i915_guc_wq_check_space+0x119/0x210 [i915]
[<
ffffffffa01da47c>] intel_logical_ring_alloc_request_extras+0x5c/0x70 [i915]
[<
ffffffffa01cdbf1>] i915_gem_request_alloc+0x91/0x170 [i915]
[<
ffffffffa01c1c07>] i915_gem_do_execbuffer.isra.25+0xbc7/0x12a0 [i915]
[<
ffffffffa01cb785>] ? i915_gem_object_get_pages_gtt+0x225/0x3c0 [i915]
[<
ffffffffa01d1fb6>] ? i915_gem_pwrite_ioctl+0xd6/0x9f0 [i915]
[<
ffffffffa01c2e68>] i915_gem_execbuffer2+0xa8/0x250 [i915]
[<
ffffffffa00f65d8>] drm_ioctl+0x258/0x4f0 [drm]
[<
ffffffffa01c2dc0>] ? i915_gem_execbuffer+0x340/0x340 [i915]
[<
ffffffff8111590d>] do_vfs_ioctl+0x2cd/0x4a0
[<
ffffffff8111eac2>] ? __fget+0x72/0xb0
[<
ffffffff81115b1c>] SyS_ioctl+0x3c/0x70
[<
ffffffff814effd7>] entry_SYSCALL_64_fastpath+0x12/0x6a
------------[ cut here ]------------
v4:
Only tear down doorbell & kunmap() client object if we actually
succeeded in allocating a client object (Tvrtko Ursulin)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93847
Original-version-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvtrko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Chris Wilson [Wed, 20 Apr 2016 11:09:52 +0000 (12:09 +0100)]
drm/i915/shrinker: Only shmemfs objects are backed by swap
Since we can only swap out shmemfs objects, those are the only ones that
can influence the ability of the shrinker to free pages. Currently, all
non-shmemfs objects have a raised pages_pin_count to protect them from
the shrinker, so this just makes the logic for can_release_pages()
clearer (and safer in future so that we don't over estimate our ability
to free up pages from future non-swappable objects).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461150592-27818-3-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Chris Wilson [Wed, 20 Apr 2016 11:09:51 +0000 (12:09 +0100)]
drm/i915/shrinker: Report "unevictable" pages
Inside the shrinker we call can_release_pages() to indicate whether or
not we can make forward progress in freeing up memory by unbinding that
object. When adding our report to oom, we should be using the same
logic.
Whilst here, change the reporting from bytes to pages so that it looks
smaller to the user!, is consistent with the neighbouring oom report
itself which displays counts in pages, and makes the unsigned long
overflow less likely.
v2: Split oversized format string into two lines
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461150592-27818-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Chris Wilson [Wed, 20 Apr 2016 11:09:50 +0000 (12:09 +0100)]
drm/i915/shrinker: Only report objects with extra pinned pages as pinned
When iterating over the bound list, we expect all objects there to have
their pages pinned (by the bound VMA). So only report those objects with
additional pin count on their pages as "pinned". These should be those
objects used for display and hardware access.
Reported-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Akash Goel <akash.goel@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461150592-27818-1-git-send-email-chris@chris-wilson.co.uk
Tvrtko Ursulin [Tue, 19 Apr 2016 15:46:09 +0000 (16:46 +0100)]
drm/i915: Remove a couple pointless WARN_ONs
Just two WARN_ONs followed by pointer dereference I spotted by accident.
v2: Remove some more of the same.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461080770-14693-1-git-send-email-tvrtko.ursulin@linux.intel.com
Tvrtko Ursulin [Tue, 19 Apr 2016 15:46:08 +0000 (16:46 +0100)]
drm/i915/gen8+: Do not enable DPF interrupt since the handler does not exist
Looks like DPF was not implemented for gen8+ but the IER and IMR
are still enabled on initialization.
Since there is no code to handle this interrupt, gate the irq
enablement behind HAS_L3_DPF in case the feature gets enabled
in the future.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tim Gore [Tue, 19 Apr 2016 14:45:52 +0000 (15:45 +0100)]
drm/i915/gen9: implement WaEnableSamplerGPGPUPreemptionSupport
WaEnableSamplerGPGPUPreemptionSupport fixes a problem
related to mid thread pre-emption.
Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461077152-31899-1-git-send-email-tim.gore@intel.com
Shubhangi Shrivastava [Tue, 12 Apr 2016 06:53:54 +0000 (12:23 +0530)]
drm/i915: Fixing eDP detection on certain platforms
Since commit
30d9aa4265fe ("drm/i915: Read sink_count dpcd always"),
the status of a DP connector depends on its sink count value.
However, some eDP panels don't set that value appropriately,
causing them to be reported as disconnected.
Fix this by ignoring sink count for eDP.
v2: Rephrased commit message. (Ander)
In case of eDP, returning status as connected if DPCD
read succeeds to avoid any further operations.
Fixes:
30d9aa4265fe ("drm/i915: Read sink_count dpcd always")
Cc: Ander Conselvan De Oliveira <conselvan2@gmail.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460444034-22320-1-git-send-email-shubhangi.shrivastava@intel.com
jim.bride@linux.intel.com [Mon, 11 Apr 2016 17:11:24 +0000 (10:11 -0700)]
drm/i915/dp/mst: Fix MST logic in intel_dp_long_pulse()
In commit
7d23e3c37bb3 ("drm/i915: Cleaning up intel_dp_hpd_pulse") some
much needed clean-up was done, but unfortunately part of the change
broke DP MST. The real issue was setting the connector state to
disconnected in the MST case, which is good, but the code then (after
a goto) checks if the connector state is not connected and shuts down
MST if this is the case, which is bad. With this change both SST and
MST seem to be happy.
v2: Add removed check further up in the function to be sure that MST
is shut down when we lose the link. (Ander)
Fixes: commit
7d23e3c37bb3 ("drm/i915: Cleaning up intel_dp_hpd_pulse")
cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
cc: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
cc: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Signed-off-by: Jim Bride <jim.bride@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: Lyude <cpaul@redhat.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460394684-7036-1-git-send-email-jim.bride@linux.intel.com
Joonas Lahtinen [Fri, 15 Apr 2016 09:03:39 +0000 (12:03 +0300)]
drm/i915: Clean up PCI config register handling
Do not use magic numbers, do not prefix stuff with "PCI_", do not
declare registers in implementation files. Also move the PCI
registers under correct comment in i915_reg.h.
v2:
- Consistently use BSM (not BDSM or other variants from PRM) (Chris)
- Also include register address to help identify the register (Chris)
v3:
- Refer to register value as *_val instead of *_reg (Chris)
v4:
- Make style checker happy
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Matthew Auld [Tue, 12 Apr 2016 15:57:42 +0000 (16:57 +0100)]
drm/i915: call kunmap_px on pt_vaddr
We need to kunmap pt_vaddr and not pt itself, otherwise we end up
mapping a bunch of pages without ever unmapping them.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Fixes:
d1c54acd67dc ("drm/i915/gtt: Introduce kmap|kunmap for dma page")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460476663-24890-4-git-send-email-matthew.auld@intel.com
Ville Syrjälä [Mon, 18 Apr 2016 16:17:51 +0000 (19:17 +0300)]
drm/i915: Wait for power cycle delay after turning off DSI panel power
The power cycle delay starts _after_ turning off the panel power. Do the
msleep after frobbing the pmic panel power gpio.
Also toss in a FIXME about optimizing away needless waits.
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Fixes:
fc45e8219907 ("drm/i915: Use the CRC gpio for panel enable/disable")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460996271-29795-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Mon, 18 Apr 2016 11:02:28 +0000 (14:02 +0300)]
drm/i915: Define HSW/BDW display power domains the right way up
Currently we're trying to define HSW/BDW power wells by what's not
included. Let's do it the other way around, so that you can actually
tell when the power well would get enabled. This will also allow us to
add new power domains without accidentally adding it to the HSW/BDW
display power domains.
The current set of domains looks rather buggy even:
- POWER_DOMAIN_MODESET is included in the display power well needlessly
- DDI-B to DDI-E were not part of the display power well when they
should be
So let's fix that up while at it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460977348-32260-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Ville Syrjälä [Mon, 18 Apr 2016 11:02:27 +0000 (14:02 +0300)]
drm/i915: Define VLV/CHV display power well domains properly
Currently we're using POWER_DOMAIN_MASK as the power domains for the
display power well on VLV/CHV. That includes all power domains even
though the disp2d/pipe-a power well is not needed for a lot of things.
Let's reduce these to what we actually need.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460977348-32260-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Ville Syrjälä [Mon, 18 Apr 2016 11:02:26 +0000 (14:02 +0300)]
drm/i915: Set .domains=POWER_DOMAIN_MASK for the always-on well
The always-on well is the same as runtime PM, so we should just
"enable" it for any power domain. Throw out the usless
FOO_ALWAYS_ON_DOMAINS defines and just use POWER_DOMAIN_MASK.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460977348-32260-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Ville Syrjälä [Mon, 18 Apr 2016 17:34:04 +0000 (20:34 +0300)]
drm/i915: Fix oops in vlv_force_pll_on()
intel_pipe_will_have_type() doesn't just look at the passied in
pipe_config, instead it expects there to be a full atomic state behind
it. Obviously that won't go so well when vlv_force_pll_on() just uses a
temp pipe_config. Fix things by using pipe_config->has_dsi_encoder
instead intel_pipe_will_have_type(INTEL_OUTPUT_DSI) to check if we need
to actually enable the DPLL.
Here's an example oops for reference:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000030
IP: [<
ffffffffa0389a5b>] intel_pipe_will_have_type+0x15/0x7b [i915]
PGD
7acda067 PUD
72696067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: i915 i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops drm intel_gtt agpgart netconsole psmouse atkbd iTCO_wdt libps2 coretemp hwmon efi_pstore intel_rapl punit_atom_debug efivars pcspkr i2c_i801 r8169 lpc_ich mii processor_thermal_device snd_soc_rt5670 intel_soc_dts_iosf snd_soc_rl6231 i2c_hid hid snd_intel_sst_acpi snd_intel_sst_core snd_soc_sst_mfld_platform snd_soc_sst_match snd_soc_core i8042 serio snd_compress snd_pcm snd_timer snd i2c_designware_platform sdhci_acpi i2c_designware_core soundcore sdhci pwm_lpss_platform mmc_core pwm_lpss spi_pxa2xx_platform evdev int3403_thermal int3400_thermal int340x_thermal_zone acpi_thermal_rel sch_fq_codel ip_tables x_tables ipv6 autofs4
CPU: 3 PID: 290 Comm: Xorg Tainted: G U 4.6.0-rc4-bsw+ #2876
Hardware name: Intel Corporation CHERRYVIEW C0 PLATFORM/Braswell CRB, BIOS BRAS.X64.X088.R00.
1510270350 10/27/2015
task:
ffff88007a8dd200 ti:
ffff880173ac4000 task.ti:
ffff880173ac4000
RIP: 0010:[<
ffffffffa0389a5b>] [<
ffffffffa0389a5b>] intel_pipe_will_have_type+0x15/0x7b [i915]
RSP: 0018:
ffff880173ac7928 EFLAGS:
00010246
RAX:
0000000000000000 RBX:
ffff880176594000 RCX:
0000000000000000
RDX:
0000000000000000 RSI:
0000000000000009 RDI:
ffff880176594000
RBP:
ffff880173ac7930 R08:
0000000000019290 R09:
0000000000000000
R10:
ffff880173ac7890 R11:
00000000000080cf R12:
ffff88017fbd4000
R13:
ffffffffa03e3c44 R14:
ffff88007492c000 R15:
ffff88007492c000
FS:
00007ff8936a6940(0000) GS:
ffff88017ef80000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000000000030 CR3:
0000000177e08000 CR4:
00000000001006e0
Stack:
ffff880176594000 ffff880173ac7948 ffffffffa0389b42 ffff880176594000
ffff880173ac7978 ffffffffa0396e02 ffff8801765b0000 ffff88007af660d8
0000000000000000 0000000000000004 ffff880173ac79c0 ffffffffa03b6b64
Call Trace:
[<
ffffffffa0389b42>] chv_compute_dpll.isra.39+0x33/0x55 [i915]
[<
ffffffffa0396e02>] vlv_force_pll_on+0x80/0xc6 [i915]
[<
ffffffffa03b6b64>] vlv_power_sequencer_pipe+0x29b/0x3dd [i915]
[<
ffffffffa03b6cd4>] _pp_stat_reg+0x2e/0x38 [i915]
[<
ffffffffa03b6dc1>] wait_panel_status+0x4c/0x1ec [i915]
[<
ffffffffa03b6fcb>] wait_panel_power_cycle+0x6a/0xb4 [i915]
[<
ffffffffa03b70da>] edp_panel_vdd_on+0xc5/0x1d1 [i915]
[<
ffffffffa03b861b>] intel_dp_aux_ch+0x55/0x572 [i915]
[<
ffffffff810af5c8>] ? mark_held_locks+0x5d/0x74
[<
ffffffff81518e61>] ? mutex_lock_nested+0x321/0x346
[<
ffffffff81094007>] ? preempt_count_sub+0xf2/0x102
[<
ffffffffa03b8cb4>] intel_dp_aux_transfer+0x17c/0x1b5 [i915]
[<
ffffffffa03028ef>] drm_dp_dpcd_access+0x62/0xed [drm_kms_helper]
[<
ffffffffa0302995>] drm_dp_dpcd_read+0x1b/0x1f [drm_kms_helper]
[<
ffffffffa03b5147>] intel_dp_dpcd_read_wake+0x31/0x69 [i915]
[<
ffffffffa03bb36a>] intel_dp_long_pulse+0x15f/0x5ed [i915]
[<
ffffffffa03bbb09>] intel_dp_detect+0x79/0x95 [i915]
[<
ffffffffa030340e>] drm_helper_probe_single_connector_modes+0xc7/0x3db [drm_kms_helper]
[<
ffffffffa029de23>] drm_mode_getconnector+0xe9/0x333 [drm]
[<
ffffffff810b1cfb>] ? lock_acquire+0x137/0x1df
[<
ffffffffa0292364>] drm_ioctl+0x266/0x3ae [drm]
[<
ffffffffa029dd3a>] ? drm_mode_getcrtc+0x126/0x126 [drm]
[<
ffffffff811af082>] vfs_ioctl+0x18/0x34
[<
ffffffff811af682>] do_vfs_ioctl+0x547/0x5fe
[<
ffffffff811b9acb>] ? __fget_light+0x62/0x71
[<
ffffffff811af77c>] SyS_ioctl+0x43/0x61
[<
ffffffff81001a82>] do_syscall_64+0x63/0xf8
[<
ffffffff8151bc9a>] entry_SYSCALL64_slow_path+0x25/0x25
Code: 35 00 40 a0 e8 97 4b ce e0 b8 17 00 00 00 5d c3 b8 17 00 00 00 c3 0f 1f 44 00 00 55 31 c0 31 d2 48 89 e5 53 48 8b 8f e8 01 00 00 <44> 8b 49 30 41 39 c1 7e 2d 4c 8b 51 38 4c 8b 41 40 49 83 3c c2
RIP [<
ffffffffa0389a5b>] intel_pipe_will_have_type+0x15/0x7b [i915]
RSP <
ffff880173ac7928>
CR2:
0000000000000030
The regressing patch wasn't exactly new (as in first posted more than
six months ago), so I'm a bit baffled how I didn't manage to hit this
myself so far.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Marius Vlad <marius.c.vlad@intel.com>
Reported-by: Marius Vlad <marius.c.vlad@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94995
Fixes:
cd2d34d9b61f ("drm/i915: Setup DPLL/DPLLMD for DSI too on VLV/CHV")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461000844-20543-1-git-send-email-ville.syrjala@linux.intel.com
Tested-by: Marius Vlad <marius.c.vlad@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Imre Deak [Mon, 18 Apr 2016 11:48:21 +0000 (14:48 +0300)]
drm/i915/gen9: Fix runtime PM refcounting in case DMC firmware isn't loaded
While we disable runtime PM and with that display power well support if
the DMC firmware isn't loaded, we still want to disable power wells
during system suspend and driver unload. So drop/reacquire the
corresponding power refcount during suspend/resume and driver unloading.
This also means we have to check if DMC is not loaded and skip enabling
DC states in the power well code.
v2:
- Reuse intel_csr_ucode_suspend() in intel_csr_ucode_fini() instead of
opencoding the former. (Chris)
- Add docbook comment to the public resume and suspend functions.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460980101-14713-1-git-send-email-imre.deak@intel.com
Imre Deak [Mon, 18 Apr 2016 07:04:21 +0000 (10:04 +0300)]
drm/i915/ddi: Fix eDP VDD handling during booting and suspend/resume
The driver's VDD on/off logic assumes that whenever the VDD is on we
also hold an AUX power domain reference. Since BIOS can leave the VDD on
during booting and resuming and on DDI platforms we won't take a
corresponding power reference, the above assumption won't hold on those
platforms and an eventual delayed VDD off work will do an extraneous AUX
power domain put resulting in a refcount underflow. Fix this the same
way we did this for non-DDI DP encoders:
commit
6d93c0c41760c0 ("drm/i915: fix VDD state tracking after system
resume")
At the same time call the DP encoder suspend handler the same way as the
non-DDI DP encoders do to flush any pending VDD off work. Leaving the
work running may cause a HW access where we don't expect this (at a point
where power domains are suspended already).
While at it remove an unnecessary function call indirection.
This fixed for me AUX refcount underflow problems on BXT during
suspend/resume.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-4-git-send-email-imre.deak@intel.com
Imre Deak [Mon, 18 Apr 2016 11:45:54 +0000 (14:45 +0300)]
drm/i915: Fix system resume if PCI device remained enabled
During system resume we depended on pci_enable_device() also putting the
device into PCI D0 state. This won't work if the PCI device was already
enabled but still in D3 state. This is because pci_enable_device() is
refcounted and will not change the HW state if called with a non-zero
refcount. Leaving the device in D3 will make all subsequent device
accesses fail.
This didn't cause a problem most of the time, since we resumed with an
enable refcount of 0. But it fails at least after module reload because
after that we also happen to leak a PCI device enable reference: During
probing we call drm_get_pci_dev() which will enable the PCI device, but
during device removal drm_put_dev() won't disable it. This is a bug of
its own in DRM core, but without much harm as it only leaves the PCI
device enabled. Fixing it is also a bit more involved, due to DRM
mid-layering and because it affects non-i915 drivers too. The fix in
this patch is valid regardless of the problem in DRM core.
v2:
- Add a code comment about the relation of this fix to the freeze/thaw
vs. the suspend/resume phases. (Ville)
- Add a code comment about the inconsistent ordering of set power state
and device enable calls. (Chris)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460979954-14503-1-git-send-email-imre.deak@intel.com
Imre Deak [Mon, 18 Apr 2016 07:04:19 +0000 (10:04 +0300)]
drm/i915: Fix error path in i915_drm_resume_early
If system resume fails, this may lead to a runtime PM wake reference
underflow used for runtime PM state checking.
Fixes:
1f814daca43a ("drm/i915: add support for checking if we hold an RPM reference")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-2-git-send-email-imre.deak@intel.com
Imre Deak [Fri, 15 Apr 2016 19:32:58 +0000 (22:32 +0300)]
drm/i915/kbl: Reset secondary power well requests left on by DMC/KVMR
The workaround added in
commit
c6782b76d31a ("drm/i915/gen9: Reset secondary power well
requests left on by DMC/KVMR")
needs to be applied on Kabylake too as shown by the corresponding
timeout errors about power well 1 and MISC IO power well disabling in
the latest CI run.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460748778-4484-1-git-send-email-imre.deak@intel.com
Ville Syrjälä [Mon, 18 Apr 2016 11:29:32 +0000 (14:29 +0300)]
drm/i915: Replace nondescript 'WARN_ON(!lret)' with a sensible error message
When a vblank wait times out in intel_atomic_wait_for_vblanks() we just
get a cryptic 'WARN_ON(!ret)' backtrace in dmesg. Repace it with
something that tells you what actually happened.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460978973-24945-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Chris Wilson [Sun, 17 Apr 2016 19:42:46 +0000 (20:42 +0100)]
drm/i915: Avoid stalling on pending flips for legacy cursor updates
The legacy cursor ioctl expects to be asynchronous with respect to other
screen updates, in particular page flips. As X updates the cursor from a
signal context, if the cursor blocks then it will stall both the input
and output chains causing bad stuttering and horrible UX.
Reported-and-tested-by: Rafael Ristovski <rafael.ristovski@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94980
Fixes:
5008e874edd34 ("drm/i915: Make wait_for_flips interruptible.")
Suggested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/1460922166-20292-1-git-send-email-chris@chris-wilson.co.uk
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Jani Nikula [Fri, 15 Apr 2016 12:47:31 +0000 (15:47 +0300)]
drm/i915/dsi: fix CHV dsi encoder hardware state readout on port C
Due to "some hardware limitation" the DPI enable bit in port C control
register does not get set on VLV. As a workaround we check the status in
pipe B conf register instead. The workaround was added in
commit
c0beefd29fcb1ca998f0f9ba41be8539f8eeba9b
Author: Gaurav K Singh <gaurav.k.singh@intel.com>
Date: Tue Dec 9 10:59:20 2014 +0530
drm/i915: Software workaround for getting the HW status of DSI Port C on BYT
Empirical evidence (on Surface 3 with DSI on port C per VBT) shows that
this is the case also on CHV, so extend the workaround to CHV. We still
have the device ready register check in place, so this should not get
confused with e.g. HDMI on pipe B.
This fixes a number of state checker warnings on CHV DSI port C.
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460724451-13810-1-git-send-email-jani.nikula@intel.com
Tvrtko Ursulin [Fri, 15 Apr 2016 10:34:53 +0000 (11:34 +0100)]
drm/i915: Show pin mapped counts and sizes in debugfs
Show a total and purgeable number of pin mapped objects
and their total and purgeable size.
Example output (new stat prefixed with a star):
# cat i915_gem_objects
19920 objects,
289243136 bytes
19920 [18466] objects,
288714752 [
267911168] bytes in gtt
0 [0] active objects, 0 [0] bytes
19917 [18466] inactive objects,
288714752 [
267911168] bytes
0 unbound objects, 0 bytes
0 purgeable objects, 0 bytes
1 pinned mappable objects,
3145728 bytes
0 fault mappable objects, 0 bytes
* 19914 [0] pin mapped objects,
285560832 [0] bytes [purgeable]
4294967296 [
268435456] gtt total
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460716493-27826-1-git-send-email-tvrtko.ursulin@linux.intel.com
Tvrtko Ursulin [Fri, 15 Apr 2016 10:34:52 +0000 (11:34 +0100)]
drm/i915: Show pin mapped status in describe_obj
Reflect the status of obj->mapping as added with the
i915_gem_object_pin_map API.
'M' was chosen to designate the pin mapped status.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Tue, 12 Apr 2016 19:14:38 +0000 (22:14 +0300)]
drm/i915: Reject 'Center' scaling mode for eDP/DSI on GMCH platforms
We don't have a LVDS_BORDER_ENABLE type of bit for either eDP or DSI,
and just trying to frob the display timings to include borders results
in a corrupted picture. So reject the 'Center' scaling mode on GMCH
platforms for eDP and DSI.
TODO: Should really filter out the unsupported modes from the prop,
but that would be fairly invasive since the prop is now created and
stored by drm core. So leave it for a rainy day.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-6-git-send-email-ville.syrjala@linux.intel.com
Tested-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Tue, 12 Apr 2016 19:14:37 +0000 (22:14 +0300)]
drm/i915: Hook up pfit for DSI
Add the scaling mode property to DSI connectors, handle changes in the
property value, and compute the panel fitter state during
.compute_config().
v2: Handle BXT as well
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-5-git-send-email-ville.syrjala@linux.intel.com
Tested-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Tue, 12 Apr 2016 19:14:36 +0000 (22:14 +0300)]
drm/i915: Eliminate {vlv,bxt}_configure_dsi_pll()
Fold the DSI PLL configuration functions into the DSI PLL
enable functions since they are small and not called from anywhere else.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-4-git-send-email-ville.syrjala@linux.intel.com
Tested-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Tue, 12 Apr 2016 19:14:35 +0000 (22:14 +0300)]
drm/i915: Compute DSI PLL parameters during .compute_config()
Compute the DSI PLL parameters during .compute_config() rather than
.pre_pll_enable() so that we can fail gracefully if we can't find
suitable parameters.
In order to do that we need to store the DSI PLL parameters in
pipe_config.
v2: Handle BXT too
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-3-git-send-email-ville.syrjala@linux.intel.com
Tested-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Tue, 12 Apr 2016 19:14:34 +0000 (22:14 +0300)]
drm/i915: Setup DPLL/DPLLMD for DSI too on VLV/CHV
Set up DPLL and DPLL_MD even when driving DSI output on VLV/CHV. While
the DPLL isn't used to provide the clock we still need the refclock, and
it appears that the pixel repeat factor also has an effect on DSI
output. So set up eveyrhing in DPLL and DPLL_MD as we would do for
DP/HDMI/VGA, but don't actually enable the DPLL or configure the
dividers via DPIO.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Jani Nikula <jani.nikula@intel.com>
Dongwon Kim [Thu, 14 Apr 2016 22:37:43 +0000 (15:37 -0700)]
drm/i915/bxt: PORT_PLL_REF_SEL bit should be set for all BXT variations
This patch is to correct one thing in this commit:
commit
25a56705332add0363e47b3a0eca001d6fbd5bec
Author: Dongwon Kim <dongwon.kim@intel.com>
Date: Wed Mar 16 18:06:13 2016 -0700
drm/i915/bxt: Reversed polarity of PORT_PLL_REF_SEL bit
This reversed bit polarity is actually common
for all BXT and APL SoCs. Therefore, revision checking
in the original commit should be removed to make
the bit set regardless of revision ID of GFX block.
Signed-off-by: Dongwon Kim <dongwon.kim@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460673463-14453-1-git-send-email-dongwon.kim@intel.com
Imre Deak [Fri, 1 Apr 2016 13:02:47 +0000 (16:02 +0300)]
drm/i915/bxt: Enable runtime PM
With the preceding fixes runtime PM should be functional, I could
runtime suspend/resume the device without problems.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-17-git-send-email-imre.deak@intel.com
Imre Deak [Fri, 1 Apr 2016 13:02:46 +0000 (16:02 +0300)]
Revert "drm/i915/bxt: Disable power well support"
With the preceding fixes power well support should be functional on
Broxton, I could enter/exit DC5 without problems.
This reverts commit
18024199579882265653bfe9e2b1a3dcb5697cd9.
CC: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-16-git-send-email-imre.deak@intel.com
Imre Deak [Mon, 4 Apr 2016 14:27:10 +0000 (17:27 +0300)]
drm/i915/bxt: Add HW state verification for DDI PHY and CDCLK
I caught a few errors in our current PHY/CDCLK programming by sanity
checking the actual programmed state, so I thought it would be also
useful for the future. In addition to verifying the state after
programming it also verify it after exiting DC5, to make sure DMC
restored/kept intact everything related.
v2:
- Inlining __phy_reg_verify_state() doesn't make sense and also
incorrect, so don't do it (PW/CI gcc)
v3:
- Rebase on latest -nightly
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459780030-15781-1-git-send-email-imre.deak@intel.com
Imre Deak [Fri, 1 Apr 2016 13:02:44 +0000 (16:02 +0300)]
drm/i915/bxt: Don't reprogram an already enabled DDI PHY
If BIOS has already programmed and enabled a PHY, don't reprogram it as
that may interfere with the currently active outputs. A follow-up patch
will add state verification, so we can catch any misconfiguration on
BIOS's behalf.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-14-git-send-email-imre.deak@intel.com
Imre Deak [Fri, 1 Apr 2016 13:02:43 +0000 (16:02 +0300)]
drm/i915/bxt: Sanitize the DBUF HW state together with CDCLK
When determining whether CDCLK is enabled by BIOS and so we should skip
reprogramming it, we didn't check the related DBUF power request and
state. In theory BIOS could enable one without the other so check for
this case and reprogram things if something is amiss.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-13-git-send-email-imre.deak@intel.com
Imre Deak [Fri, 1 Apr 2016 13:02:42 +0000 (16:02 +0300)]
drm/i915/bxt: Don't toggle power well 1 on-demand
Power well 1 is managed by the DMC firmware so don't toggle it on-demand
from the driver. This means we need to follow the BSpec display
initialization sequence during driver loading and resuming (both system
and runtime) and enable power well 1 only once there. Afterwards DMC
will toggle power well 1 whenever entering/exiting DC5.
For this to work we also need to do away getting the PLL power domain,
since that just kept runtime PM disabled for good.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-12-git-send-email-imre.deak@intel.com
Imre Deak [Fri, 1 Apr 2016 13:02:41 +0000 (16:02 +0300)]
drm/i915/bxt: Power down DDI PHYs separately during the per PHY uninit
The power-down step logically belongs to the individual PHY uninit
sequence so move it there. The only functional change is that we will
power down now PHY 1 separately before PHY 0 and preserve the other bits
in the register which are defined as reserved.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-11-git-send-email-imre.deak@intel.com
Imre Deak [Fri, 1 Apr 2016 13:02:40 +0000 (16:02 +0300)]
drm/i915/bxt: Pass drm_i915_private to DDI PHY, CDCLK helpers
For internal APIs passing dev_priv is preferred to reduce indirections,
so convert over a few DDI PHY, CDCLK helpers.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-10-git-send-email-imre.deak@intel.com
Imre Deak [Mon, 4 Apr 2016 12:42:57 +0000 (15:42 +0300)]
drm/i915/skl: Unexport skl_pw1_misc_io_init
On Broxton we need to enable/disable power well 1 during the init/unit
display sequence similarly to Skylake/Kabylake. The code for this will
be added in a follow-up patch, but to prepare for that unexport
skl_pw1_misc_io_init(). It's a simple function called only from a single
place and having it inlined in the Skylake display core init/unit
functions will make it easier to compare it with its Broxton
counterpart.
This also flips the order of Misc IO and power well 1 disabling which
matches the enabling order. The specification doesn't prescribe the
disabling order, so this should be fine.
v2:
- Fix incorrect enable vs. disable power well call in
skl_display_core_uninit() (Patrik)
- Add commit comment about chaning the order of PW1 and Misc IO power
well disabling (Patrik)
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459773777-10701-1-git-send-email-imre.deak@intel.com
Imre Deak [Fri, 1 Apr 2016 13:02:38 +0000 (16:02 +0300)]
drm/i915/bxt: Suspend power domains during suspend-to-idle
On SKL/KBL suspend-to-idle (aka freeze/s0ix) is performed with DMC
firmware assistance where the target display power state is DC6. On
Broxton on the other hand we don't use the firmware for this, but rely
instead on a manual DC9 flow. For this we have to uninitialize the
display following the BSpec display uninit sequence, just as during
S3/S4, so make sure we follow this sequence.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-8-git-send-email-imre.deak@intel.com
Imre Deak [Fri, 1 Apr 2016 13:02:37 +0000 (16:02 +0300)]
drm/i915/gen9: Fix DMC/DC state asserts
The display power well support and DC state management doesn't depend on
runtime PM support, so remove the incorrect asserts about this.
Also Broxton does support DC5, so the related assert in
assert_can_enable_dc5() is incorrect. There is a more generic and
correct assert for this already in gen9_set_dc_state(), so we can remove
all the other ones.
At the same time convert WARNs to WARN_ONCE for consistency with the
other DC state asserts.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-7-git-send-email-imre.deak@intel.com
Imre Deak [Fri, 1 Apr 2016 13:02:36 +0000 (16:02 +0300)]
drm/i915/gen9: Make power well disabling synchronous
So far we only power well enabling was synchronous not disabling. Since
we don't exactly know how the firmware (both DMC and PCU) synchronizes
against the actual power well state during DC transitions, make the
disabling also synchronous.
CC: Mika Kuoppala <mika.kuoppala@linux.intel.com>
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-6-git-send-email-imre.deak@intel.com
Imre Deak [Tue, 5 Apr 2016 10:26:05 +0000 (13:26 +0300)]
drm/i915/gen9: Reset secondary power well requests left on by DMC/KVMR
DMC forces on power well 1 and the misc IO power well by setting the
corresponding request bits both in the BIOS and the DEBUG power well
request registers. This is somewhat unexpected since the firmware should
really just save and restore state but not alter it. We also depend on
being able to disable power well 1, and the misc IO power well before
entering S3/S4 on BXT and SKL or entering DC9 on BXT. To fix this make
sure these request bits are cleared whenever we want to disable the
given power wells.
On SKL there is another twist where the firmware also clears the power
well 1 request bit in HSW_POWER_WELL_DRIVER (but not that of the misc IO
power well). This happens to not cause a problem due to the forced-on
request bits in the other request registers.
I've filed a bug about all this, but fixing that may take a while and
having this sanity check in place makes sense even for future firmware
versions.
At the same time also check the KVMR request bits. I haven't seen this
being altered, but we don't expect any request bits in here either, so
sanitize this register as well.
v2:
- Apply the workaround on SKL as well. I noticed the related failure
from the CI report, later Patrik also reported seeing it on his
machine.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459851965-6137-1-git-send-email-imre.deak@intel.com
Imre Deak [Fri, 1 Apr 2016 13:02:34 +0000 (16:02 +0300)]
drm/i915/bxt: Add a note about BXT_PORT_CL1CM_DW30 being read-only
This register is read-only, so we have never actually set
OCL2_LDOFUSE_PWR_DIS in it as specified by the specification. Add a code
comment about this. I filed a specification update request to clarify
this there.
CC: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-4-git-send-email-imre.deak@intel.com
Imre Deak [Fri, 1 Apr 2016 13:02:33 +0000 (16:02 +0300)]
drm/i915/bxt: Fix GRC code register field definitions
This has been corrected in BSpec quite some time ago, but we missed it
somehow. The wrong field definitions resulted in configuring PHY0 with
an incorrect GRC value.
v2:
- Remove the FIXME comment, we left in the code exactly about this
issue. (Ville)
CC: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-3-git-send-email-imre.deak@intel.com
Imre Deak [Fri, 1 Apr 2016 13:02:32 +0000 (16:02 +0300)]
drm/i915/bxt: Reject DMC firmware versions with known bugs
DMC version 1.06 has a known bug, where the firmware polls forever for a
port PLL to lock, if the PLL was disabled when entering DC5, which locks
up the machine. Version 1.07 fixes this, so make that the minimum
required version on BXT.
CC: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-2-git-send-email-imre.deak@intel.com
Gustavo Padovan [Thu, 14 Apr 2016 17:48:15 +0000 (10:48 -0700)]
drm/i915: use drm_crtc_send_vblank_event()
Replace the legacy drm_send_vblank_event() with the new helper function.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460656118-16766-4-git-send-email-gustavo@padovan.org
Ville Syrjälä [Thu, 14 Apr 2016 11:39:02 +0000 (14:39 +0300)]
drm/i915: Use fw_domains_put_with_fifo() on HSW
HSW still has the wake FIFO, so let's check it.
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Deepak S <deepak.s@linux.intel.com>
Fixes:
05a2fb157e44 ("drm/i915: Consolidate forcewake code")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460633942-24013-1-git-send-email-ville.syrjala@linux.intel.com
Cc: stable@vger.kernel.org
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Ville Syrjälä [Wed, 13 Apr 2016 18:19:58 +0000 (21:19 +0300)]
drm/i915: Split gen8_gt_irq_handler into ack+handle
As we did on VLV, split the gt irq handling to ack and handler phases on
CHV. Leave the BDW+ codepath mostly intact for now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-13-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Wed, 13 Apr 2016 18:19:57 +0000 (21:19 +0300)]
drm/i915: Eliminate passing dev+dev_priv to {snb,ilk}_gt_irq_handler()
It looks silly to pass both dev and dev_priv to the snb/ilk gt irq
handlers. Just pass dev_priv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-12-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Wed, 13 Apr 2016 18:19:56 +0000 (21:19 +0300)]
drm/i915: Move gt/pm irq handling out from irq disabled section on VLV
No need to actually handle the GT/PM interrupt while we have interrupt
sources disabled. Move the actual processing to happen after we've
restored VLV_IER and master interrupt enable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-11-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Wed, 13 Apr 2016 18:19:55 +0000 (21:19 +0300)]
drm/i915: Split VLV/CVH PIPESTAT handling into ack+handler
Minimize the amount of stuff we do with interrupt sources disabled by
splitting the PIPESTAT irq handling into ack+handler phases.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-10-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Wed, 13 Apr 2016 18:19:54 +0000 (21:19 +0300)]
drm/i915: Split PORT_HOTPLUG_STAT ack out from i9xx_hpd_irq_handler()
Split the VLV/CHV hoplug irq handling to ack and handler phases. This
way we can move the actual irq handling outside the section where
we have disabled the interrupt sources.
For now, we leave things as is for pre-VLV GMCH platforms, but
eventually they could get the same treatment.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Wed, 13 Apr 2016 18:19:53 +0000 (21:19 +0300)]
drm/i915: Move variables to narrower scope in VLV/CHV irq handlers
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-8-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Wed, 13 Apr 2016 18:19:52 +0000 (21:19 +0300)]
drm/i915: Eliminate loop from VLV irq handler
Now that we've dealt with the races in clearing IIR bits via VLV_IER
and the master interrupt enable, we can go ahead aliminate the loop
from the VLV interrupt handler.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-7-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Wed, 13 Apr 2016 18:19:51 +0000 (21:19 +0300)]
drm/i915: Clear VLV_IER around irq processing
On VLV/CHV the master interrupt enable bit only affects GT/PM
interrupts. Display interrupts are not affected by the master
irq control.
Also it seems that the CPU interrupt will only be generated when
the combined result of all GT/PM/display interrupts has a 0->1
edge. We already use the master interrupt enable bit to make sure
GT/PM interrupt can generate such an edge if we don't end up clearing
all IIR bits. We must do the same for display interrupts, and for
that we can simply clear out VLV_IER, and restore after we've acked
all the interrupts we are about to process.
So with both master interrupt enable and VLV_IER cleared out, we will
guarantee that there will be a 0->1 edge if any IIR bits are still set
at the end, and thus another CPU interrupt will be generated.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes:
579de73b048a ("drm/i915: Exit cherryview_irq_handler() after one pass")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Wed, 13 Apr 2016 18:19:50 +0000 (21:19 +0300)]
drm/i915: Clear VLV_MASTER_IER around irq processing
Like on CHV, let's clear out the master irq enable bit when we ack
GT/PM interrupts. This will allow GT/PM interrupts to re-raise the
CPU interrupt if we fail to clear all the bits from the IIR(s).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Wed, 13 Apr 2016 18:19:49 +0000 (21:19 +0300)]
drm/i915: Clear VLV_IIR after PIPESTAT
On VLV/CHV VLV_IIR is not double double buffered, and it doesn't detect
edges from PIPESTAT & co. like it does on gen4. Instead it just
directly latches the level from PIPESTAT & co. That means we must clear
VLV_IIR after PIPESTAT & co. or else we'll get a spurious bit in VLV_IIR
every single time.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Wed, 13 Apr 2016 18:19:48 +0000 (21:19 +0300)]
drm/i915: Set up VLV_MASTER_IER consistently
We're lacking VLV_MASTER_IER setup from valleyview_irq_preinstall(), so
add it there. Also cargo cult in some POSTING_READ()s to match the other
platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Wed, 13 Apr 2016 18:19:47 +0000 (21:19 +0300)]
drm/i915: Use GEN8_MASTER_IRQ_CONTROL consistently
Use GEN8_MASTER_IRQ_CONTROL instead of DE_MASTER_IRQ_CONTROL or
MASTER_INTERRUPT_ENABLE with the GEN8_MASTER_IRQ register. They're
all bit 31 so there's no actual bug here, but let's be consistent
which name we use for the bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Wed, 13 Apr 2016 18:09:30 +0000 (21:09 +0300)]
drm/i915: Ignore GTFIFODBG FIFO free entry fields on CHV
On CHV GTFIFODBG has some read-only bits to indicate the number
of free FIFO entries. Ignore these when checking to see if any
of the sticky error bits are set.
This gets rid of these during device resume:
[drm:cherryview_enable_rps] GT fifo had a previous error
1080000
While at it, move the assignments out of the if().
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460570970-14073-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Peter Antoine [Wed, 13 Apr 2016 14:03:25 +0000 (15:03 +0100)]
drm/i915/mocs: Program MOCS for all engines on init
Allow for the MOCS to be programmed for all engines.
Currently we program the MOCS when the first render batch
goes through. This works on most platforms but fails on
platforms that do not run a render batch early,
i.e. headless servers. The patch now programs all initialised engines
on init and the RCS is programmed again within the initial batch. This
is done for predictable consistency with regards to the hardware
context.
Hardware context loading sets the values of the MOCS for RCS
and L3CC. Programming them from within the batch makes sure that
the render context is valid, no matter what the previous state of
the saved-context was.
v2: posted correct version to the mailing list.
v3: moved programming to within engine->init_hw() (Chris Wilson)
v4: code formatting and white-space changes. (Chris Wilson)
Testcase: igt/gem_mocs_settings
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460556205-6644-1-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Wed, 13 Apr 2016 16:35:15 +0000 (17:35 +0100)]
drm/i915: Late request cancellations are harmful
Conceptually, each request is a record of a hardware transaction - we
build up a list of pending commands and then either commit them to
hardware, or cancel them. However, whilst building up the list of
pending commands, we may modify state outside of the request and make
references to the pending request. If we do so and then cancel that
request, external objects then point to the deleted request leading to
both graphical and memory corruption.
The easiest example is to consider object/VMA tracking. When we mark an
object as active in a request, we store a pointer to this, the most
recent request, in the object. Then we want to free that object, we wait
for the most recent request to be idle before proceeding (otherwise the
hardware will write to pages now owned by the system, or we will attempt
to read from those pages before the hardware is finished writing). If
the request was cancelled instead, that wait completes immediately. As a
result, all requests must be committed and not cancelled if the external
state is unknown.
All that remains of i915_gem_request_cancel() users are just a couple of
extremely unlikely allocation failures, so remove the API entirely.
A consequence of committing all incomplete requests is that we generate
excess breadcrumbs and fill the ring much more often with dummy work. We
have completely undone the outstanding_last_seqno optimisation.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93907
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-16-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Wed, 13 Apr 2016 16:35:14 +0000 (17:35 +0100)]
drm/i915: Reorganise legacy context switch to cope with late failure
After mi_set_context() succeeds, we need to update the state of the
engine's last_context. This ensures that we hold a pin on the context
whilst the hardware may write to it. However, since we didn't complete
the post-switch setup of the context, we need to force the subsequent
use of the same context to complete the setup (which means updating
should_skip_switch()).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-15-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Wed, 13 Apr 2016 16:35:13 +0000 (17:35 +0100)]
drm/i915: Split out !RCS legacy context switching
Having the !RCS legacy context switch threaded through the RCS switching
code makes it much harder to follow and understand. In the next patch, I
want to fix a bug handling the incomplete switch, this is made much
simpler if we segregate the two paths now.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-14-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Wed, 13 Apr 2016 16:35:12 +0000 (17:35 +0100)]
drm/i915: Move the mb() following release-mmap into release-mmap
As paranoia, we want to ensure that the CPU's PTEs have been revoked for
the object before we return from i915_gem_release_mmap(). This allows us
to rely on there being no outstanding memory accesses from userspace
and guarantees serialisation of the code against concurrent access just
by calling i915_gem_release_mmap().
v2: Reduce the mb() into a wmb() following the revoke.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Goel, Akash" <akash.goel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-13-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Wed, 13 Apr 2016 16:35:11 +0000 (17:35 +0100)]
drm/i915: Force ringbuffers to not be at offset 0
For reasons unknown Sandybridge GT1 (at least) will eventually hang when
it encounters a ring wraparound at offset 0. The test case that
reproduces the bug reliably forces a large number of interrupted context
switches, thereby causing very frequent ring wraparounds, but there are
similar bug reports in the wild with the same symptoms, seqno writes
stop just before the wrap and the ringbuffer at address 0. It is also
timing crucial, but adding various delays hasn't helped pinpoint where
the window lies.
Whether the fault is restricted to the ringbuffer itself or the GTT
addressing is unclear, but moving the ringbuffer fixes all the hangs I
have been able to reproduce.
References: (e.g.) https://bugs.freedesktop.org/show_bug.cgi?id=93262
Testcase: igt/gem_exec_whisper/render-contexts-interruptible #snb-gt1
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-12-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Wed, 13 Apr 2016 16:35:10 +0000 (17:35 +0100)]
drm/i915: Prevent machine death on Ivybridge context switching
Two concurrent writes into the same register cacheline has the chance of
killing the machine on Ivybridge and other gen7. This includes LRI
emitted from the command parser. The MI_SET_CONTEXT itself serves as
serialising barrier and prevents the pair of register writes in the first
packet from triggering the fault. However, if a second switch-context
immediately occurs then we may have two adjacent blocks of LRI to the
same registers which may then trigger the hang. To counteract this we
need to insert a delay after the second register write using SRM.
This is easiest to reproduce with something like
igt/gem_ctx_switch/interruptible that triggers back-to-back context
switches (with no operations in between them in the command stream,
which requires the execbuf operation to be interrupted after the
MI_SET_CONTEXT) but can be observed sporadically elsewhere when running
interruptible igt. No reports from the wild though, so it must be of low
enough frequency that no one has correlated the random machine freezes
with i915.ko
The issue was introduced with
commit
2c550183476dfa25641309ae9a28d30feed14379 [v3.19]
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Dec 16 10:02:27 2014 +0000
drm/i915: Disable PSMI sleep messages on all rings around context switches
Testcase: igt/gem_ctx_switch/render-interruptible #ivb
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-11-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Wed, 13 Apr 2016 16:35:09 +0000 (17:35 +0100)]
drm/i915: Suppress error message when GPU resets are disabled
If we do not have lowlevel support for reseting the GPU, or if the user
has explicitly disabled reseting the device, the failure is expected.
Since it is an expected failure, we should be using a lower priority
message than *ERROR*, perhaps NOTICE. In the absence of DRM_NOTICE, just
emit the expected failure as a DEBUG message.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-10-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Wed, 13 Apr 2016 16:35:08 +0000 (17:35 +0100)]
drm/i915: Prevent leaking of -EIO from i915_wait_request()
Reporting -EIO from i915_wait_request() has proven very troublematic
over the years, with numerous hard-to-reproduce bugs cropping up in the
corner case of where a reset occurs and the code wasn't expecting such
an error.
If the we reset the GPU or have detected a hang and wish to reset the
GPU, the request is forcibly complete and the wait broken. Currently, we
report either -EAGAIN or -EIO in order for the caller to retreat and
restart the wait (if appropriate) after dropping and then reacquiring
the struct_mutex (essential to allow the GPU reset to proceed). However,
if we take the view that the request is complete (no further work will
be done on it by the GPU because it is dead and soon to be reset), then
we can proceed with the task at hand and then drop the struct_mutex
allowing the reset to occur. This transfers the burden of checking
whether it is safe to proceed to the caller, which in all but one
instance it is safe - completely eliminating the source of all spurious
-EIO.
Of note, we only have two API entry points where we expect that
userspace can observe an EIO. First is when submitting an execbuf, if
the GPU is terminally wedged, then the operation cannot succeed and an
-EIO is reported. Secondly, existing userspace uses the throttle ioctl
to detect an already wedged GPU before starting using HW acceleration
(or to confirm that the GPU is wedged after an error condition). So if
the GPU is wedged when the user calls throttle, also report -EIO.
v2: Split more carefully the change to i915_wait_request() and assorted
ABI from the reset handling.
v3: Add a couple of WARN_ON(EIO) to the interruptible modesetting code
so that we don't start to leak EIO there in future (and break our hang
resistant modesetting).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-9-git-send-email-chris@chris-wilson.co.uk
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-1-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Wed, 13 Apr 2016 16:35:07 +0000 (17:35 +0100)]
drm/i915: Simplify reset_counter handling during atomic modesetting
Now that the reset_counter is stored on the request, we can rearrange
the code to handle reading the counter versus waiting during the atomic
modesetting for readibility (by deleting the hairiest of codes).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-8-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Wed, 13 Apr 2016 16:35:06 +0000 (17:35 +0100)]
drm/i915: Store the reset counter when constructing a request
As the request is only valid during the same global reset epoch, we can
record the current reset_counter when constructing the request and reuse
it when waiting upon that request in future. This removes a very hairy
atomic check serialised by the struct_mutex at the time of waiting and
allows us to transfer those waits to a central dispatcher for all
waiters and all requests.
PS: With per-engine resets, we obviously cannot assume a global reset
epoch for the requests - a per-engine epoch makes the most sense. The
challenge then is how to handle checking in the waiter for when to break
the wait, as the fine-grained reset may also want to requeue the
request (i.e. the assumption that just because the epoch changes the
request is completed may be broken - or we just avoid breaking that
assumption with the fine-grained resets).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-7-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Wed, 13 Apr 2016 16:35:05 +0000 (17:35 +0100)]
drm/i915: Tighten reset_counter for reset status
In the reset_counter, we use two bits to track a GPU hang and reset. The
low bit is a "reset-in-progress" flag that we set to signal when we need
to break waiters in order for the recovery task to grab the mutex. As
soon as the recovery task has the mutex, we can clear that flag (which
we do by incrementing the reset_counter thereby incrementing the gobal
reset epoch). By clearing that flag when the recovery task holds the
struct_mutex, we can forgo a second flag that simply tells GEM to ignore
the "reset-in-progress" flag.
The second flag we store in the reset_counter is whether the
reset failed and we consider the GPU terminally wedged. Whilst this flag
is set, all access to the GPU (at least through GEM rather than direct mmio
access) is verboten.
PS: Fun is in store, as in the future we want to move from a global
reset epoch to a per-engine reset engine with request recovery.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-6-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Wed, 13 Apr 2016 16:35:04 +0000 (17:35 +0100)]
drm/i915: Simplify checking of GPU reset_counter in display pageflips
If we, when we store the reset_counter for the operation, we ensure that
it is not in a wedged or in the middle of a reset, we can then assert that
if any reset occurs the reset_counter must change. Later we can just
compare the operation's reset epoch against the current counter to see
if we need to abort the operation (to handle the hang).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-5-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Wed, 13 Apr 2016 16:35:03 +0000 (17:35 +0100)]
drm/i915: Hide the atomic_read(reset_counter) behind a helper
This is principally a little bit of syntatic sugar to hide the
atomic_read()s throughout the code to retrieve the current reset_counter.
It also provides the other utility functions to check the reset state on the
already read reset_counter, so that (in later patches) we can read it once
and do multiple tests rather than risk the value changing between tests.
v2: Be more strict on converting existing i915_reset_in_progress() over to
the more verbose i915_reset_in_progress_or_wedged().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-4-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Wed, 13 Apr 2016 16:35:02 +0000 (17:35 +0100)]
drm/i915: Add GEM debugging Kconfig option
Currently there is a #define to enable extra BUG_ON for debugging
requests and associated activities. I want to expand its use to cover
all of GEM internals (so that we can saturate the code with asserts).
We can add a Kconfig option to make it easier to enable - with the usual
caveats of not enabling unless explicitly requested.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-3-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Wed, 13 Apr 2016 16:35:01 +0000 (17:35 +0100)]
drm/i915: Disentangle i915_drv.h includes
Separate out the layers of includes (linux, drm, intel, i915) so that it
is a little easier to order our definitions between our multiple
reentrant headers. A couple of headers needed fixes to make them more
standalone (forgotten includes, forward declarations etc).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-2-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Wed, 13 Apr 2016 16:35:00 +0000 (17:35 +0100)]
drm/i915: Force clean compilation with -Werror
Our driver compiles clean (nowadays thanks to 0day) but for me, at least,
it would be beneficial if the compiler threw an error rather than a
warning when it found a piece of suspect code. (I use this to
compile-check patch series and want to break on the first compiler error
in order to fix the patch.)
v2: Kick off a new "Debugging" submenu for i915.ko
At this point, we applied it to the kernel and promptly kicked it out
again as it broke buildbots (due to a compiler warning on 32bits):
commit
908d759b210effb33d927a8cb6603a16448474e4
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue May 26 07:46:21 2015 +0200
Revert "drm/i915: Force clean compilation with -Werror"
v3: Avoid enabling -Werror for allyesconfig/allmodconfig builds, using
COMPILE_TEST as a suitable proxy suggested by Andrew Morton. (Damien)
Only make the option available for EXPERT to reinforce that the option
should not be casually enabled.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-1-git-send-email-chris@chris-wilson.co.uk
Mika Kuoppala [Wed, 13 Apr 2016 14:26:44 +0000 (17:26 +0300)]
drm/i915: Calculate edram size
With gen9+ the edram capabilities are defined so
that we can calculate the edram (ellc) size accordingly.
Note that there are undefined combinations for some subset of
edram capability bits. Return the closest size for undefined indexes.
Even if we get it wrong with beginning of future gen enabling, the size
information is currently only used for boot message and in debugfs entry.
v2: Use function instead of hard to read macro (Daniel)
v3: s/INTEL_INFO/INTEL_GEN (Matthew)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460557604-7126-2-git-send-email-mika.kuoppala@intel.com
Mika Kuoppala [Wed, 13 Apr 2016 14:26:43 +0000 (17:26 +0300)]
drm/i915: Store and use edram capabilities
Store the edram capabilities instead of only the size of
edram. This is preparatory patch to allow edram size calculation
based on edram capability bits for gen9+. With gen9 the
edram is behind llc and is a separate entity. With hsw/bdw
it was more of a victim cache for LLC so the name 'eLLC' might
be warranted. Regardless, rename all mentions of eLLC to EDRAM to
clear the confusion.
v2: return bytes for edram size (Chris)
s/eLLC/eDRAM in output if we are gen > 8
v3: rebase, INTEL_GEN (Chris)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>