OSDN Git Service
Ganesh Goudar [Fri, 19 May 2017 12:20:15 +0000 (17:50 +0530)]
cxgb4 : retrieve port information from firmware
issue get port information command to firmware to retrieve port
information and update if it is different from what was last
recorded and also add indication for supported link modes for
firmware port types FW_PORT_TYPE_SFP28, FW_PORT_TYPE_KR_SFP28,
FW_PORT_TYPE_CR4_QSFP.
Based on the original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sivakumar Krishnasamy [Fri, 19 May 2017 09:30:38 +0000 (05:30 -0400)]
ibmveth: Support to enable LSO/CSO for Trunk VEA.
Current largesend and checksum offload feature in ibmveth driver,
- Source VM sends the TCP packets with ip_summed field set as
CHECKSUM_PARTIAL and TCP pseudo header checksum is placed in
checksum field
- CHECKSUM_PARTIAL flag in SKB will enable ibmveth driver to mark
"no checksum" and "checksum good" bits in transmit buffer descriptor
before the packet is delivered to pseries PowerVM Hypervisor
- If ibmveth has largesend capability enabled, transmit buffer descriptors
are market accordingly before packet is delivered to Hypervisor
(along with mss value for packets with length > MSS)
- Destination VM's ibmveth driver receives the packet with "checksum good"
bit set and so, SKB's ip_summed field is set with CHECKSUM_UNNECESSARY
- If "largesend" bit was on, mss value is copied from receive descriptor
into SKB's gso_size and other flags are appropriately set for
packets > MSS size
- The packet is now successfully delivered up the stack in destination VM
The offloads described above works fine for TCP communication among VMs in
the same pseries server ( VM A <=> PowerVM Hypervisor <=> VM B )
We are now enabling support for OVS in pseries PowerVM environment. One of
our requirements is to have ibmveth driver configured in "Trunk" mode, when
they are used with OVS. This is because, PowerVM Hypervisor will no more
bridge the packets between VMs, instead the packets are delivered to
IO Server which hosts OVS to bridge them between VMs or to external
networks (flow shown below),
VM A <=> PowerVM Hypervisor <=> IO Server(OVS) <=> PowerVM Hypervisor
<=> VM B
In "IO server" the packet is received by inbound Trunk ibmveth and then
delivered to OVS, which is then bridged to outbound Trunk ibmveth (shown
below),
Inbound Trunk ibmveth <=> OVS <=> Outbound Trunk ibmveth
In this model, we hit the following issues which impacted the VM
communication performance,
- Issue 1: ibmveth doesn't support largesend and checksum offload features
when configured as "Trunk". Driver has explicit checks to prevent
enabling these offloads.
- Issue 2: SYN packet drops seen at destination VM. When the packet
originates, it has CHECKSUM_PARTIAL flag set and as it gets delivered to
IO server's inbound Trunk ibmveth, on validating "checksum good" bits
in ibmveth receive routine, SKB's ip_summed field is set with
CHECKSUM_UNNECESSARY flag. This packet is then bridged by OVS (or Linux
Bridge) and delivered to outbound Trunk ibmveth. At this point the
outbound ibmveth transmit routine will not set "no checksum" and
"checksum good" bits in transmit buffer descriptor, as it does so only
when the ip_summed field is CHECKSUM_PARTIAL. When this packet gets
delivered to destination VM, TCP layer receives the packet with checksum
value of 0 and with no checksum related flags in ip_summed field. This
leads to packet drops. So, TCP connections never goes through fine.
- Issue 3: First packet of a TCP connection will be dropped, if there is
no OVS flow cached in datapath. OVS while trying to identify the flow,
computes the checksum. The computed checksum will be invalid at the
receiving end, as ibmveth transmit routine zeroes out the pseudo
checksum value in the packet. This leads to packet drop.
- Issue 4: ibmveth driver doesn't have support for SKB's with frag_list.
When Physical NIC has GRO enabled and when OVS bridges these packets,
OVS vport send code will end up calling dev_queue_xmit, which in turn
calls validate_xmit_skb.
In validate_xmit_skb routine, the larger packets will get segmented into
MSS sized segments, if SKB has a frag_list and if the driver to which
they are delivered to doesn't support NETIF_F_FRAGLIST feature.
This patch addresses the above four issues, thereby enabling end to end
largesend and checksum offload support for better performance.
- Fix for Issue 1 : Remove checks which prevent enabling TCP largesend and
checksum offloads.
- Fix for Issue 2 : When ibmveth receives a packet with "checksum good"
bit set and if its configured in Trunk mode, set appropriate SKB fields
using skb_partial_csum_set (ip_summed field is set with
CHECKSUM_PARTIAL)
- Fix for Issue 3: Recompute the pseudo header checksum before sending the
SKB up the stack.
- Fix for Issue 4: Linearize the SKBs with frag_list. Though we end up
allocating buffers and copying data, this fix gives
upto 4X throughput increase.
Note: All these fixes need to be dropped together as fixing just one of
them will lead to other issues immediately (especially for Issues 1,2 & 3).
Signed-off-by: Sivakumar Krishnasamy <ksiva@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 21 May 2017 16:56:57 +0000 (12:56 -0400)]
Merge branch 'qed-next'
Yuval Mintz says:
====================
qed/qede updates
This series contains some general minor fixes and enhancements:
- #1, #2 and #9 correct small missing ethtool functionality.
- #3, #6 and #8 correct minor issues in driver, but those are either
print-related or unexposed in existing code.
- #4 adds proper support to TLB mode bonding.
- #10 is meant to improve performance on varying cache-line sizes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru [Sun, 21 May 2017 09:11:00 +0000 (12:11 +0300)]
qede: Support 1G advertisment.
Some variants of adapters support the 1G speed capability. Need to
allow the configuration of 1G speed if adapter supports it.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tomer Tayar [Sun, 21 May 2017 09:10:59 +0000 (12:10 +0300)]
qed: Fix setting of Management bitfields
The management firmware HSI contains masks which are already
shifted to their right place, so QED_MFW_SET_FIELD() is clearing
incorrect fields by shifting the mask by the offset.
Luckily, today we set the fields in an incrementing order [so we're
not erasing any previously set fields], but this still needs fixing.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mintz, Yuval [Sun, 21 May 2017 09:10:58 +0000 (12:10 +0300)]
qede: qedr closure after setting state
This is benign, but it makes more sense to start the close sequence
only after changing the internal state [in case it would once care].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mintz, Yuval [Sun, 21 May 2017 09:10:57 +0000 (12:10 +0300)]
qed: Correct print in iscsi error-flow
If too many CQs are requested, qed would print the available
number as if it's a resource and not a feature leading to the
wrong print.
Fixes:
08737a3fa30a ("qed: Inform qedi the number of possible CQs")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tomer Tayar [Sun, 21 May 2017 09:10:56 +0000 (12:10 +0300)]
qed: Revise alloc/setup/free flow
Re-organize the logic that allocates and frees memory of various
sub-components of the hw-function -
a. No need to pass pointers to said structure as parameters;
The internal logic knows exactly where to find/set the data.
b. Nullify pointers after cleanup to prevent possible errors to
re-entrant code.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mintz, Yuval [Sun, 21 May 2017 09:10:55 +0000 (12:10 +0300)]
qede: Don't use an internal MAC field
Driver maintains its primary MAC in a private field which
gets updated when ndo_dev_set_mac() gets called.
However, there are flows where the primary MAC of the device can change
without said NDO being called [bond device in TLB mode configuring
slaves' addresses], resulting in a configuration where there's a mismatch
between what's apparent to user [the netdevice's value] and what's
configured in the HW [the private value].
As we don't have any real motivation of maintaining this
private field, simply remove it and start using the netdevice's
field instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru [Sun, 21 May 2017 09:10:54 +0000 (12:10 +0300)]
qede: Add missing Status-block free
When destroying the datapath channels, qede doesn't notify qed of the
released status blocks which were acquired during the initialization.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru [Sun, 21 May 2017 09:10:53 +0000 (12:10 +0300)]
qede: Honor user request for Tx buffers
Driver always allocates the maximal number of tx-buffers irrespective of
actual Tx ring config.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mintz, Yuval [Sun, 21 May 2017 09:10:52 +0000 (12:10 +0300)]
qede: Allow WoL to activate by default
When management firmware declares that the device is WoL-capable,
the default driver behavior would be to allow the management firmware
to take the decision of whether it's actually needed or not.
Problem is ethtool interface doesn't have a 'default' kind
of option, and user would see the interface WoL as disabled,
which doesn't accurately reflect the actual configuration.
More-so, if the user actually wants to explicitly disable WoL he'd have
to first enable it [otherwise ethtool would block the command].
Instead of allowing management to make the decision, enable WoL by
default on all devices capable of it.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 19 May 2017 23:41:45 +0000 (19:41 -0400)]
Merge branch 'xgene-check-all-RGMII-phy-mode-variants'
Iyappan Subramanian says:
====================
Check all RGMII phy mode variants
This patch set,
- adds phy_interface_mode_is_rgmii() helper function
- addresses review comment from previous patch set, by calling
phy_interface_mode_is_rgmii() to address all RGMII variants
v2: Address review comments from v1
- adds phy_interface_mode_is_rgmii() helper function
- addresses review comment from previous patch set, by calling
phy_interface_mode_is_rgmii() to address all RGMII variants
v1:
- Initial version
====================
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Iyappan Subramanian [Thu, 18 May 2017 22:13:44 +0000 (15:13 -0700)]
xgene: Check all RGMII phy mode variants
This patch addresses the review comment from the previous patch set,
by using phy_interface_mode_is_rgmii() helper function to address
all RGMII phy mode variants.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Iyappan Subramanian [Thu, 18 May 2017 22:13:43 +0000 (15:13 -0700)]
phy: Add helper function to check phy interface mode
Added helper function that checks phy_mode is RGMII (all variants)
'bool phy_interface_mode_is_rgmii(phy_interface_t mode)'
Changed the following function, to use the above.
'bool phy_interface_is_rgmii(struct phy_device *phydev)'
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 19 May 2017 23:21:32 +0000 (19:21 -0400)]
Merge branch 'net-fix-CRC32c-in-the-forwarding-path'
Davide Caratti says:
====================
net: fix CRC32c in the forwarding path
Current kernel allows offloading CRC32c computation when SCTP packets
are generated, setting skb->ip_summed to CHECKSUM_PARTIAL, if the
underlying device features have NETIF_F_SCTP_CRC set. However, after these
packets are forwarded, they may land on a device where CRC32c offloading is
not available: as a consequence, transmission is done with wrong CRC32c.
It's not possible to use sctp_compte_cksum() in the forwarding path
and in most drivers, because it needs symbols exported by libcrc32c module.
Patch 1 and 2 of this series try to solve this problem, introducing a new
helper function, namely skb_crc32c_csum_help(), that can be used to resolve
CHECKSUM_PARTIAL when crc32c is needed instead of Internet Checksum.
Currently, we need to parse the packet headers to understand what algorithm
is needed to resolve CHECKSUM_PARTIAL. We can speedup things by storing
this information in the skb metadata, and use it to call an appropriate
helper (skb_checksum_help or skb_crc32c_csum_help), or leave the packet
unmodified when the NIC is able to offload the checksum computation.
Patch 3 deprecates skb->csum_bad to free one bit in skb metadata; patch 4
introduces skb->csum_not_inet, providing skb with an indication on the
algorithm needed to resolve CHECKSUM_PARTIAL.
Patch 5 and 6 fix the kernel forwarding path and openvswitch datapath,
where skb_checksum_help was unconditionally called to resolve CHECKSUM_PARTIAL,
thus generating wrong CRC32c in forwarded SCTP packets.
Finally, patch 7 updates documentation to provide a better description of
possible values of skb->ip_summed.
Some further work is still possible:
* drivers that parse the packet header to correctly resolve CHECKSUM_PARTIAL
(e.g. ixgbe_tx_csum()) can benefit from testing skb->csum_not_inet to avoid
calling ip_hdr(skb)->protocol or ixgbe_ipv6_csum_is_sctp(skb).
* drivers that call skb_checksum_help() to resolve CHECKSUM_PARTIAL can
call skb_csum_hwoffload_help to avoid corrupting SCTP packets.
Changes v2->v3:
- patch 1/7: more standard declaration of stub variables
Changes v1->v2:
- none
Changes RFCv4->v1:
- patch 2/7: use WARN_ON_ONCE() instead of BUG_ON(), and avoid computing
CRC32c on the error path.
- patch 3/7: don't invert tests on the values of same_flow and
NAPI_GRO_CB(skb)->flush in dev_gro_receive(), it's useless and it breaks
GRO functionality as reported by kernel test robot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Thu, 18 May 2017 13:44:43 +0000 (15:44 +0200)]
sk_buff.h: improve description of CHECKSUM_{COMPLETE, UNNECESSARY}
Add FCoE to the list of protocols that can set CHECKSUM_UNNECESSARY; add a
note to CHECKSUM_COMPLETE section to specify that it does not apply to SCTP
and FCoE protocols.
Suggested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Thu, 18 May 2017 13:44:42 +0000 (15:44 +0200)]
openvswitch: more accurate checksumming in queue_userspace_packet()
if skb carries an SCTP packet and ip_summed is CHECKSUM_PARTIAL, it needs
CRC32c in place of Internet Checksum: use skb_csum_hwoffload_help to avoid
corrupting such packets while queueing them towards userspace.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Thu, 18 May 2017 13:44:41 +0000 (15:44 +0200)]
net: more accurate checksumming in validate_xmit_skb()
skb_csum_hwoffload_help() uses netdev features and skb->csum_not_inet to
determine if skb needs software computation of Internet Checksum or crc32c
(or nothing, if this computation can be done by the hardware). Use it in
place of skb_checksum_help() in validate_xmit_skb() to avoid corruption
of non-GSO SCTP packets having skb->ip_summed equal to CHECKSUM_PARTIAL.
While at it, remove references to skb_csum_off_chk* functions, since they
are not present anymore in Linux _ see commit
cf53b1da73bd ("Revert
"net: Add driver helper functions to determine checksum offloadability"").
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Thu, 18 May 2017 13:44:40 +0000 (15:44 +0200)]
net: use skb->csum_not_inet to identify packets needing crc32c
skb->csum_not_inet carries the indication on which algorithm is needed to
compute checksum on skb in the transmit path, when skb->ip_summed is equal
to CHECKSUM_PARTIAL. If skb carries a SCTP packet and crc32c hasn't been
yet written in L4 header, skb->csum_not_inet is assigned to 1; otherwise,
assume Internet Checksum is needed and thus set skb->csum_not_inet to 0.
Suggested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Thu, 18 May 2017 13:44:39 +0000 (15:44 +0200)]
sk_buff: remove support for csum_bad in sk_buff
This bit was introduced with commit
5a21232983aa ("net: Support for
csum_bad in skbuff") to reduce the stack workload when processing RX
packets carrying a wrong Internet Checksum. Up to now, only one driver and
GRO core are setting it.
Suggested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Thu, 18 May 2017 13:44:38 +0000 (15:44 +0200)]
net: introduce skb_crc32c_csum_help
skb_crc32c_csum_help is like skb_checksum_help, but it is designed for
checksumming SCTP packets using crc32c (see RFC3309), provided that
libcrc32c.ko has been loaded before. In case libcrc32c is not loaded,
invoking skb_crc32c_csum_help on a skb results in one the following
printouts:
warn_crc32c_csum_update: attempt to compute crc32c without libcrc32c.ko
warn_crc32c_csum_combine: attempt to compute crc32c without libcrc32c.ko
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Thu, 18 May 2017 13:44:37 +0000 (15:44 +0200)]
skbuff: add stub to help computing crc32c on SCTP packets
sctp_compute_checksum requires crc32c symbol (provided by libcrc32c), so
it can't be used in net core. Like it has been done previously with other
symbols (e.g. ipv6_dst_lookup), introduce a stub struct skb_checksum_ops
to allow computation of crc32c checksum in net core after sctp.ko (and thus
libcrc32c) has been loaded.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Soheil Hassas Yeganeh [Tue, 16 May 2017 21:39:02 +0000 (17:39 -0400)]
tcp: warn on negative reordering values
Commit
bafbb9c73241 ("tcp: eliminate negative reordering
in tcp_clean_rtx_queue") fixes an issue for negative
reordering metrics.
To be resilient to such errors, warn and return
when a negative metric is passed to tcp_update_reordering().
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 18 May 2017 20:11:32 +0000 (16:11 -0400)]
Merge git://git./linux/kernel/git/davem/net
Wei Yongjun [Thu, 18 May 2017 15:34:41 +0000 (15:34 +0000)]
net/mlx5e: Fix possible memory leak
'encap_header' is malloced and should be freed before leaving from
the error handling cases, otherwise it will cause memory leak.
Fixes:
232c001398ae ("net/mlx5e: Add support to neighbour update flow")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Thu, 18 May 2017 15:26:29 +0000 (15:26 +0000)]
qed: Remove unused including <linux/version.h>
Remove including <linux/version.h> that is not needed.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Thu, 18 May 2017 15:24:52 +0000 (15:24 +0000)]
ibmvnic: fix missing unlock on error in __ibmvnic_reset()
Add the missing unlock before return from function __ibmvnic_reset()
in the error handling case.
Fixes:
ed651a10875f ("ibmvnic: Updated reset handling")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 18 May 2017 19:04:41 +0000 (12:04 -0700)]
Merge tag 'md/4.12-rc2' of git://git./linux/kernel/git/shli/md
Pull MD fixes from Shaohua Li:
- Several bug fixes for raid5-cache from Song Liu, mainly handle
journal disk error
- Fix bad block handling in choosing raid1 disk from Tomasz Majchrzak
- Simplify external metadata array sysfs handling from Artur
Paszkiewicz
- Optimize raid0 discard handling from me, now raid0 will dispatch
large discard IO directly to underlayer disks.
* tag 'md/4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
raid1: prefer disk without bad blocks
md/r5cache: handle sync with data in write back cache
md/r5cache: gracefully handle journal device errors for writeback mode
md/raid1/10: avoid unnecessary locking
md/raid5-cache: in r5l_do_submit_io(), submit io->split_bio first
md/md0: optimize raid0 discard handling
md: don't return -EAGAIN in md_allow_write for external metadata arrays
md/raid5: make use of spin_lock_irq over local_irq_disable + spin_lock
Matthias Kaehlcke [Thu, 18 May 2017 17:57:19 +0000 (10:57 -0700)]
net1080: Remove unused function nc_dump_ttl()
The function is not used, removing it fixes the following warning when
building with clang:
drivers/net/usb/net1080.c:271:20: error: unused function
'nc_dump_ttl' [-Werror,-Wunused-function]
Also remove the definition of TTL_THIS, which is only used in
nc_dump_ttl()
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthias Kaehlcke [Thu, 18 May 2017 17:45:33 +0000 (10:45 -0700)]
r8152: Remove unused function usb_ocp_read()
The function is not used, removing it fixes the following warning when
building with clang:
drivers/net/usb/r8152.c:825:5: error: unused function 'usb_ocp_read'
[-Werror,-Wunused-function]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 18 May 2017 18:40:21 +0000 (11:40 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Don't allow negative TCP reordering values, from Soheil Hassas
Yeganeh.
2) Don't overflow while parsing ipv6 header options, from Craig Gallek.
3) Handle more cleanly the case where an individual route entry during
a dump will not fit into the allocated netlink SKB, from David
Ahern.
4) Add missing CONFIG_INET dependency for mlx5e, from Arnd Bergmann.
5) Allow neighbour updates to converge more quickly via gratuitous
ARPs, from Ihar Hrachyshka.
6) Fix compile error from CONFIG_INET is disabled, from Eric Dumazet.
7) Fix use after free in x25 protocol init, from Lin Zhang.
8) Valid VLAN pvid ranges passed into br_validate(), from Tobias
Jungel.
9) NULL out address lists in child sockets in SCTP, this is similar to
the fix we made for inet connection sockets last week. From Eric
Dumazet.
10) Fix NULL deref in mlxsw driver, from Ido Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
mlxsw: spectrum: Avoid possible NULL pointer dereference
sh_eth: Do not print an error message for probe deferral
sh_eth: Use platform device for printing before register_netdev()
mlxsw: spectrum_router: Fix rif counter freeing routine
mlxsw: spectrum_dpipe: Fix incorrect entry index
cxgb4: update latest firmware version supported
qmi_wwan: add another Lenovo EM74xx device ID
sctp: do not inherit ipv6_{mc|ac|fl}_list from parent
udp: make *udp*_queue_rcv_skb() functions static
bridge: netlink: check vlan_default_pvid range
net: ethernet: faraday: To support device tree usage.
net: x25: fix one potential use-after-free issue
bpf: adjust verifier heuristics
ipv6: Check ip6_find_1stfragopt() return value properly.
selftests/bpf: fix broken build due to types.h
bnxt_en: Check status of firmware DCBX agent before setting DCB_CAP_DCBX_HOST.
bnxt_en: Call bnxt_dcb_init() after getting firmware DCBX configuration.
net: fix compile error in skb_orphan_partial()
ipv6: Prevent overrun when parsing v6 header options
neighbour: update neigh timestamps iff update is effective
...
Linus Torvalds [Thu, 18 May 2017 18:21:10 +0000 (11:21 -0700)]
Merge git://git./linux/kernel/git/davem/sparc
Pull sparc fixes from David Miller:
"Three sparc bug fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc/ftrace: Fix ftrace graph time measurement
sparc: Fix -Wstringop-overflow warning
sparc64: Fix mapping of 64k pages with MAP_FIXED
Linus Torvalds [Thu, 18 May 2017 18:17:34 +0000 (11:17 -0700)]
Merge tag 'kbuild-fixes-v4.12' of git://git./linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fix from Masahiro Yamada:
"Fix headers_install to not delete pre-existing headers in the install
destination"
* tag 'kbuild-fixes-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: skip install/check of headers right under uapi directories
Mintz, Yuval [Thu, 18 May 2017 16:41:04 +0000 (19:41 +0300)]
qed: Utilize FW 8.20.0.0
This pushes qed [and as result, all qed* drivers] into using 8.20.0.0
firmware. The changes are mostly contained in qed with minor changes
to qedi due to some HSI changes.
Content-wise, the firmware contains fixes to various issues exposed
since the release of the previous firmware, including:
- Corrects iSCSI fast retransmit when data digest is enabled.
- Stop draining packets when receiving several consecutive PFCs.
- Prevent possible assertion when consecutively opening/closing
many connections.
- Prevent possible assertion due to too long BDQ fetch time.
In addition, the new firmware would allow us to later add iWARP support
in qed and qedr.
Changes from previous version
-----------------------------
- V2: Fix warning in qed_debug.c
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 18 May 2017 16:15:58 +0000 (09:15 -0700)]
tcp: fix tcp_rearm_rto()
skbs in (re)transmit queue no longer have a copy of jiffies
at the time of the transmit : skb->skb_mstamp is now in usec unit,
with no correlation to tcp_jiffies32.
We have to convert rto from jiffies to usec, compute a time difference
in usec, then convert the delta to HZ units.
Fixes:
9a568de4818d ("tcp: switch TCP TS option (RFC 7323) to 1ms clock")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 18 May 2017 17:04:42 +0000 (10:04 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ebiederm/user-namespace
Pull pid namespace fixes from Eric Biederman:
"These are two bugs that turn out to have simple fixes that were
reported during the merge window. Both of these issues have existed
for a while and it just happens that they both were reported at almost
the same time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
pid_ns: Fix race between setns'ed fork() and zap_pid_ns_processes()
pid_ns: Sleep in TASK_INTERRUPTIBLE in zap_pid_ns_processes
Linus Torvalds [Thu, 18 May 2017 16:38:09 +0000 (09:38 -0700)]
Merge tag 'hwmon-for-linus-v4.12-rc2' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix problem with hotplug state machine in coretemp driver"
* tag 'hwmon-for-linus-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (coretemp) Handle frozen hotplug state correctly
Ido Schimmel [Thu, 18 May 2017 11:03:52 +0000 (13:03 +0200)]
mlxsw: spectrum: Avoid possible NULL pointer dereference
In case we got an FDB notification for a port that doesn't exist we
execute an FDB entry delete to prevent it from re-appearing the next
time we poll for notifications.
If the operation failed we would trigger a NULL pointer dereference as
'mlxsw_sp_port' is NULL.
Fix it by reporting the error using the underlying bus device instead.
Fixes:
12f1501e7511 ("mlxsw: spectrum: remove FDB entry in case we get unknown object notification")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 18 May 2017 09:14:01 +0000 (10:14 +0100)]
liquidio: make the spinlock octeon_devices_lock static
octeon_devices_lock can be made static as it does not need to be
in global scope.
Cleans up sparse warning: "warning: symbol 'octeon_devices_lock'
was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Thu, 18 May 2017 13:01:35 +0000 (15:01 +0200)]
sh_eth: Do not print an error message for probe deferral
EPROBE_DEFER is not an error, hence printing an error message like
sh-eth
ee700000.ethernet: failed to initialise MDIO
may confuse the user.
To fix this, suppress the error message in case of probe deferral.
While at it, shorten the message, and add the actual error code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Thu, 18 May 2017 13:01:34 +0000 (15:01 +0200)]
sh_eth: Use platform device for printing before register_netdev()
The MDIO initialization failure message is printed using the network
device, before it has been registered, leading to:
(null): failed to initialise MDIO
Use the platform device instead to fix this:
sh-eth
ee700000.ethernet: failed to initialise MDIO
Fixes:
daacf03f0bbfefee ("sh_eth: Register MDIO bus before registering the network device")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 18 May 2017 15:18:20 +0000 (11:18 -0400)]
Merge tag 'linux-can-next-for-4.13-
20170518' of git://git./linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2017-05-18
this is a pull request of 4 patches for net-next/master.
All 4 patches are by Quentin Schulz, they add deep deep Suspend/Resume
support to the m_can driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Arkadi Sharshevsky [Thu, 18 May 2017 07:22:45 +0000 (09:22 +0200)]
mlxsw: spectrum_dpipe: Fix sparse warnings
drivers/net/ethernet/mellanox/mlxsw//spectrum_dpipe.c:221:52: warning:
Using plain integer as NULL pointer
drivers/net/ethernet/mellanox/mlxsw//spectrum_dpipe.c:221:74: warning:
Using plain integer as NULL pointer
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 18 May 2017 15:04:00 +0000 (11:04 -0400)]
Merge branch 'mlxsw-fixes'
Jiri Pirko says:
====================
mlxsw: couple of fixes
Couple of fixes from Arkadi
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Arkadi Sharshevsky [Thu, 18 May 2017 07:18:53 +0000 (09:18 +0200)]
mlxsw: spectrum_router: Fix rif counter freeing routine
During rif counter freeing the counter index can be invalid. Add check
of validity before freeing the counter.
Fixes:
e0c0afd8aa4e ("mlxsw: spectrum: Support for counters on router interfaces")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arkadi Sharshevsky [Thu, 18 May 2017 07:18:52 +0000 (09:18 +0200)]
mlxsw: spectrum_dpipe: Fix incorrect entry index
In case of disabled counters the entry index will be incorrect. Fix this
by moving the entry index set before the counter status check.
Fixes:
2ba5999f009d ("mlxsw: spectrum: Add Support for erif table entries access")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Anholt [Thu, 18 May 2017 00:32:12 +0000 (17:32 -0700)]
net: dsa: b53: Add compatible strings for the Cygnus-family BCM11360.
Cygnus is a small family of SoCs, of which we currently have
devicetree for BCM11360 and BCM58300. The 11360's B53 is mostly the
same as 58xx, just requiring a tiny bit of setup that was previously
missing.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 18 May 2017 14:40:20 +0000 (10:40 -0400)]
Merge branch 'dsa-headers-cleanup'
Vivien Didelot says:
====================
net: dsa: headers cleanup
The DSA core files share a common private header file. Include the DSA
public header there instead of independently in each core source file.
DSA core and its drivers use switchdev, thus include switchdev.h in the
public DSA header. This allows us to get rid of the forward declaration
and use typedef defined by switchdev.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Wed, 17 May 2017 19:46:05 +0000 (15:46 -0400)]
net: dsa: use switchdev_obj_dump_cb_t everywhere
Now that the DSA public header includes switchdev.h, use the provided
switchdev_obj_dump_cb_t typedef for the object dump callback.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Wed, 17 May 2017 19:46:04 +0000 (15:46 -0400)]
net: dsa: include switchdev.h only once
DSA drivers and core use switchdev. Include switchdev.h only once, in
the dsa.h public header, so that inclusion in DSA drivers or forward
declarations of switchdev structures in not necessary anymore.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Wed, 17 May 2017 19:46:03 +0000 (15:46 -0400)]
net: dsa: include dsa.h only once
The public include/net/dsa.h file is meant for DSA drivers, while all
DSA core files share a common private header net/dsa/dsa_priv.h file.
Ensure that dsa_priv.h is the only DSA core file to include net/dsa.h,
and add a new line to separate absolute and relative headers at the same
time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Vagin [Wed, 17 May 2017 18:39:05 +0000 (11:39 -0700)]
net: fix __skb_try_recv_from_queue to return the old behavior
This function has to return NULL on a error case, because there is a
separate error variable.
The offset has to be changed only if skb is returned
v2: fix udp code to not use an extra variable
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Fixes:
65101aeca522 ("net/sock: factor out dequeue/peek with offset cod")
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Wed, 17 May 2017 18:38:16 +0000 (00:08 +0530)]
cxgb4: update latest firmware version supported
Change t4fw_version.h to update latest firmware version
number to 1.16.43.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Wed, 17 May 2017 16:31:39 +0000 (19:31 +0300)]
net: make struct dst_entry::dev first member
struct dst_entry::dev is used most often. Move it so it can be
accessed without imm8 offset on x86_64.
add/remove: 0/0 grow/shrink: 9/239 up/down: 52/-413 (-361)
function old new delta
dst_rcu_free 126 138 +12
fnhe_flush_routes 211 219 +8
rt_set_nexthop 747 754 +7
rt_cache_route 85 91 +6
rt6_release 209 215 +6
dst_release 107 111 +4
dst_destroy_rcu 29 33 +4
dn_dst_check_expire 329 333 +4
dn_insert_route 484 485 +1
xfrm_resolve_and_create_bundle 2991 2990 -1
...
ip_route_me_harder 1163 1157 -6
__ip_append_data.isra 2730 2724 -6
ip6_forward 3052 3045 -7
callforward_do_filter 659 651 -8
dst_gc_task 571 549 -22
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 18 May 2017 14:28:49 +0000 (10:28 -0400)]
Merge branch 'fsl_ucc_hdlc-enhancements'
Signed-off-by: David S. Miller <davem@davemloft.net>
Holger Brunck [Wed, 17 May 2017 15:24:39 +0000 (17:24 +0200)]
powerpc/85xx/kmcent2: use hdlc busmode for UCC1
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Holger Brunck [Wed, 17 May 2017 15:24:38 +0000 (17:24 +0200)]
net/wan/fsl_ucc_hdlc: add hdlc-bus support
This adds support for hdlc-bus mode to the fsl_ucc_hdlc driver. This can
be enabled with the "fsl,hdlc-bus" property in the DTS node of the
corresponding ucc.
This aligns the configuration of the UPSMR and GUMR registers to what is
done in our ucc_hdlc driver (that only support hdlc-bus mode) and with
the QuickEngine's documentation for hdlc-bus mode.
GUMR/SYNL is set to AUTO for the busmode as in this case the CD signal
is ignored. The brkpt_support is enabled to set the HBM1 bit in the
CMXUCR register to configure an open-drain connected HDLC bus.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Holger Brunck [Wed, 17 May 2017 15:24:37 +0000 (17:24 +0200)]
fsl/qe: add bit description for SYNL register for GUMR
Add the bitmask for the two bit SYNL register according to the QUICK
Engine Reference Manual.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Holger Brunck [Wed, 17 May 2017 15:24:36 +0000 (17:24 +0200)]
net/wan/fsl_ucc_hdlc: call qe_setbrg only for loopback mode
We can't assume that we are always in loopback mode if rx and tx clock
have the same clock source. If we want to use HDLC busmode we also have
the same clock source but we are not in loopback mode. So move the
setting of the baudrate generator after the check for property for the
loopback mode.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Holger Brunck [Wed, 17 May 2017 15:24:35 +0000 (17:24 +0200)]
net/wan/fsl_ucc_hdlc: fix incorrect memory allocation
We need space for the struct qe_bd and not for a pointer to this struct.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Holger Brunck [Wed, 17 May 2017 15:24:34 +0000 (17:24 +0200)]
net/wan/fsl_ucc_hdlc: fix wrong indentation
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Holger Brunck [Wed, 17 May 2017 15:24:33 +0000 (17:24 +0200)]
net/wan/fsl_ucc_hdlc: fix unitialized variable warnings
This fixes the following compiler warnings:
drivers/net/wan/fsl_ucc_hdlc.c: In function 'ucc_hdlc_poll':
warning: 'skb' may be used uninitialized in this function
[-Wmaybe-uninitialized]
skb->mac_header = skb->data - skb->head;
and
drivers/net/wan/fsl_ucc_hdlc.c: In function 'ucc_hdlc_probe':
drivers/net/wan/fsl_ucc_hdlc.c:1127:3: warning: 'utdm' may be used
uninitialized in this function [-Wmaybe-uninitialized]
kfree(utdm);
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Holger Brunck [Wed, 17 May 2017 15:24:32 +0000 (17:24 +0200)]
net/wan/fsl_ucc_hdlc: cleanup debug traces
Some of the tracing seems to be remaining traces for basic driver
development. They can be removed now, as they cause noisy printouts.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Wed, 17 May 2017 14:31:41 +0000 (16:31 +0200)]
qmi_wwan: add another Lenovo EM74xx device ID
In their infinite wisdom, and never ending quest for end user frustration,
Lenovo has decided to use a new USB device ID for the wwan modules in
their 2017 laptops. The actual hardware is still the Sierra Wireless
EM7455 or EM7430, depending on region.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 17 May 2017 14:16:40 +0000 (07:16 -0700)]
sctp: do not inherit ipv6_{mc|ac|fl}_list from parent
SCTP needs fixes similar to
83eaddab4378 ("ipv6/dccp: do not inherit
ipv6_mc_list from parent"), otherwise bad things can happen.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 17 May 2017 12:52:16 +0000 (14:52 +0200)]
udp: make *udp*_queue_rcv_skb() functions static
Since the udp memory accounting refactor, we don't need any more
to export the *udp*_queue_rcv_skb(). Make them static and fix
a couple of sparse warnings:
net/ipv4/udp.c:1615:5: warning: symbol 'udp_queue_rcv_skb' was not
declared. Should it be static?
net/ipv6/udp.c:572:5: warning: symbol 'udpv6_queue_rcv_skb' was not
declared. Should it be static?
Fixes:
850cbaddb52d ("udp: use it's own memory accounting schema")
Fixes:
c915fe13cbaa ("udplite: fix NULL pointer dereference")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Wed, 17 May 2017 10:30:44 +0000 (13:30 +0300)]
net: make struct net_device::tx_queue_len unsigned int
4 billion packet queue is something unthinkable so use 32-bit value
for now.
Space savings on x86_64:
add/remove: 0/0 grow/shrink: 3/70 up/down: 16/-131 (-115)
function old new delta
change_tx_queue_len 94 108 +14
qdisc_create 1176 1177 +1
alloc_netdev_mqs 1124 1125 +1
xenvif_alloc 533 532 -1
x25_asy_setup 167 166 -1
...
tun_queue_resize 945 940 -5
pfifo_fast_enqueue 167 162 -5
qfq_init_qdisc 168 158 -10
tap_queue_resize 810 799 -11
transmit 719 698 -21
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Jungel [Wed, 17 May 2017 07:29:12 +0000 (09:29 +0200)]
bridge: netlink: check vlan_default_pvid range
Currently it is allowed to set the default pvid of a bridge to a value
above VLAN_VID_MASK (0xfff). This patch adds a check to br_validate and
returns -EINVAL in case the pvid is out of bounds.
Reproduce by calling:
[root@test ~]# ip l a type bridge
[root@test ~]# ip l a type dummy
[root@test ~]# ip l s bridge0 type bridge vlan_filtering 1
[root@test ~]# ip l s bridge0 type bridge vlan_default_pvid 9999
[root@test ~]# ip l s dummy0 master bridge0
[root@test ~]# bridge vlan
port vlan ids
bridge0 9999 PVID Egress Untagged
dummy0 9999 PVID Egress Untagged
Fixes:
0f963b7592ef ("bridge: netlink: add support for default_pvid")
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Tobias Jungel <tobias.jungel@bisdn.de>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Wed, 17 May 2017 08:50:36 +0000 (09:50 +0100)]
udp: make function udp_skb_dtor_locked static
Function udp_skb_dtor_locked does not need to be in global scope
so make it static to fix sparse warning:
net/ipv4/udp.c: warning: symbol 'udp_skb_dtor_locked' was not
declared. Should it be static?
Fixes:
6dfb4367cd911d ("udp: keep the sk_receive_queue held when splicing")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Greentime Hu [Wed, 17 May 2017 07:28:19 +0000 (15:28 +0800)]
net: ethernet: faraday: To support device tree usage.
To support device tree usage for ftmac100.
Signed-off-by: Greentime Hu <green.hu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 18 May 2017 14:07:42 +0000 (10:07 -0400)]
Merge branch 'vhost_net-rx-batch-dequeuing'
Jason Wang says:
====================
vhost_net rx batch dequeuing
This series tries to implement rx batching for vhost-net. This is done
by batching the dequeuing from skb_array which was exported by
underlayer socket and pass the sbk back through msg_control to finish
userspace copying. This is also the requirement for more batching
implemention on rx path.
Tests shows at most 7.56% improvment bon rx pps on top of batch
zeroing and no obvious changes for TCP_STREAM/TCP_RR result.
Please review.
Thanks
Changes from V4:
- drop batch zeroing patch
- renew the performance numbers
- move skb pointer array out of vhost_net structure
Changes from V3:
- add batch zeroing patch to fix the build warnings
Changes from V2:
- rebase to net-next HEAD
- use unconsume helpers to put skb back on releasing
- introduce and use vhost_net internal buffer helpers
- renew performance numbers on top of batch zeroing
Changes from V1:
- switch to use for() in __ptr_ring_consume_batched()
- rename peek_head_len_batched() to fetch_skbs()
- use skb_array_consume_batched() instead of
skb_array_consume_batched_bh() since no consumer run in bh
- drop the lockless peeking patch since skb_array could be resized, so
it's not safe to call lockless one
====================
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 17 May 2017 04:14:45 +0000 (12:14 +0800)]
vhost_net: try batch dequing from skb array
We used to dequeue one skb during recvmsg() from skb_array, this could
be inefficient because of the bad cache utilization and spinlock
touching for each packet. This patch tries to batch them by calling
batch dequeuing helpers explicitly on the exported skb array and pass
the skb back through msg_control for underlayer socket to finish the
userspace copying. Batch dequeuing is also the requirement for more
batching improvement on receive path.
Tests were done by pktgen on tap with XDP1 in guest. Host is Intel(R)
Xeon(R) CPU E5-2650 0 @ 2.00GHz.
rx batch | pps
0 2.25Mpps
1 2.33Mpps (+3.56%)
4 2.33Mpps (+3.56%)
16 2.35Mpps (+4.44%)
64 2.42Mpps (+7.56%) <- Default rx batching
128 2.40Mpps (+6.67%)
256 2.38Mpps (+5.78%)
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 17 May 2017 04:14:44 +0000 (12:14 +0800)]
tap: support receiving skb from msg_control
This patch makes tap_recvmsg() can receive from skb from its caller
through msg_control. Vhost_net will be the first user.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 17 May 2017 04:14:43 +0000 (12:14 +0800)]
tun: support receiving skb through msg_control
This patch makes tun_recvmsg() can receive from skb from its caller
through msg_control. Vhost_net will be the first user.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 17 May 2017 04:14:42 +0000 (12:14 +0800)]
tap: export skb_array
This patch exports skb_array through tap_get_skb_array(). Caller can
then manipulate skb array directly.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 17 May 2017 04:14:41 +0000 (12:14 +0800)]
tun: export skb_array
This patch exports skb_array through tun_get_skb_array(). Caller can
then manipulate skb array directly.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 17 May 2017 04:14:40 +0000 (12:14 +0800)]
skb_array: introduce batch dequeuing
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 17 May 2017 04:14:39 +0000 (12:14 +0800)]
ptr_ring: introduce batch dequeuing
This patch introduce a batched version of consuming, consumer can
dequeue more than one pointers from the ring at a time. We don't care
about the reorder of reading here so no need for compiler barrier.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 17 May 2017 04:14:38 +0000 (12:14 +0800)]
skb_array: introduce skb_array_unconsume
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael S. Tsirkin [Wed, 17 May 2017 04:14:37 +0000 (12:14 +0800)]
ptr_ring: add ptr_ring_unconsume
Applications that consume a batch of entries in one go
can benefit from ability to return some of them back
into the ring.
Add an API for that - assuming there's space. If there's no space
naturally can't do this and have to drop entries, but this implies ring
is full so we'd likely drop some anyway.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
linzhang [Wed, 17 May 2017 04:05:07 +0000 (12:05 +0800)]
net: x25: fix one potential use-after-free issue
The function x25_init is not properly unregister related resources
on error handler.It is will result in kernel oops if x25_init init
failed, so add properly unregister call on error handler.
Also, i adjust the coding style and make x25_register_sysctl properly
return failure.
Signed-off-by: linzhang <xiaolou4617@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quentin Schulz [Fri, 5 May 2017 13:50:33 +0000 (15:50 +0200)]
can: m_can: add deep Suspend/Resume support
This adds Power Management deep Suspend/Resume support for Bosch M_CAN
chip.
When entering deep sleep, the clocks are gated, the interrupts are
disabled. When resuming from deep sleep, the chip needs to be
reinitialized, the clocks ungated and the interrupts enabled.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Quentin Schulz [Fri, 5 May 2017 13:50:32 +0000 (15:50 +0200)]
can: m_can: factorize clock gating and ungating
This creates a function to ungate M_CAN clocks and another to gate the
same clocks, then swaps all gating/ungating code with their respective
function.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Quentin Schulz [Fri, 5 May 2017 13:50:31 +0000 (15:50 +0200)]
can: m_can: make m_can_start and m_can_stop symmetric
This moves clocks gating outside of the m_can_stop function as the
m_can_start function does not (and cannot, at least in current
implementation) ungate clocks. This way, both functions can now be used
symmetrically.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Quentin Schulz [Fri, 5 May 2017 13:50:30 +0000 (15:50 +0200)]
can: m_can: move Message RAM initialization to function
To avoid possible ECC/parity checksum errors when reading an
uninitialized buffer, the entire Message RAM is initialized when probing
the driver. This initialization is done in the same function reading the
Device Tree properties.
This patch moves the RAM initialization to a separate function so it can
be called separately from device initialization from Device Tree.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Daniel Borkmann [Thu, 18 May 2017 01:00:06 +0000 (03:00 +0200)]
bpf: adjust verifier heuristics
Current limits with regards to processing program paths do not
really reflect today's needs anymore due to programs becoming
more complex and verifier smarter, keeping track of more data
such as const ALU operations, alignment tracking, spilling of
PTR_TO_MAP_VALUE_ADJ registers, and other features allowing for
smarter matching of what LLVM generates.
This also comes with the side-effect that we result in fewer
opportunities to prune search states and thus often need to do
more work to prove safety than in the past due to different
register states and stack layout where we mismatch. Generally,
it's quite hard to determine what caused a sudden increase in
complexity, it could be caused by something as trivial as a
single branch somewhere at the beginning of the program where
LLVM assigned a stack slot that is marked differently throughout
other branches and thus causing a mismatch, where verifier
then needs to prove safety for the whole rest of the program.
Subsequently, programs with even less than half the insn size
limit can get rejected. We noticed that while some programs
load fine under pre 4.11, they get rejected due to hitting
limits on more recent kernels. We saw that in the vast majority
of cases (90+%) pruning failed due to register mismatches. In
case of stack mismatches, majority of cases failed due to
different stack slot types (invalid, spill, misc) rather than
differences in spilled registers.
This patch makes pruning more aggressive by also adding markers
that sit at conditional jumps as well. Currently, we only mark
jump targets for pruning. For example in direct packet access,
these are usually error paths where we bail out. We found that
adding these markers, it can reduce number of processed insns
by up to 30%. Another option is to ignore reg->id in probing
PTR_TO_MAP_VALUE_OR_NULL registers, which can help pruning
slightly as well by up to 7% observed complexity reduction as
stand-alone. Meaning, if a previous path with register type
PTR_TO_MAP_VALUE_OR_NULL for map X was found to be safe, then
in the current state a PTR_TO_MAP_VALUE_OR_NULL register for
the same map X must be safe as well. Last but not least the
patch also adds a scheduling point and bumps the current limit
for instructions to be processed to a more adequate value.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 18 May 2017 02:54:11 +0000 (22:54 -0400)]
ipv6: Check ip6_find_1stfragopt() return value properly.
Do not use unsigned variables to see if it returns a negative
error or not.
Fixes:
2423496af35d ("ipv6: Prevent overrun when parsing v6 header options")
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song [Wed, 17 May 2017 22:18:05 +0000 (15:18 -0700)]
selftests/bpf: fix broken build due to types.h
Commit
0a5539f66133 ("bpf: Provide a linux/types.h override
for bpf selftests.") caused a build failure for tools/testing/selftest/bpf
because of some missing types:
$ make -C tools/testing/selftests/bpf/
...
In file included from /home/yhs/work/net-next/tools/testing/selftests/bpf/test_pkt_access.c:8:
../../../include/uapi/linux/bpf.h:170:3: error: unknown type name '__aligned_u64'
__aligned_u64 key;
...
/usr/include/linux/swab.h:160:8: error: unknown type name '__always_inline'
static __always_inline __u16 __swab16p(const __u16 *p)
...
The type __aligned_u64 is defined in linux:include/uapi/linux/types.h.
The fix is to copy missing type definition into
tools/testing/selftests/bpf/include/uapi/linux/types.h.
Adding additional include "string.h" resolves __always_inline issue.
Fixes:
0a5539f66133 ("bpf: Provide a linux/types.h override for bpf selftests.")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 17 May 2017 21:21:15 +0000 (14:21 -0700)]
Merge tag 'for-4.12/dm-fixes-2' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a couple DM thin provisioning fixes
- a few request-based DM and DM multipath fixes for issues that were
made when merging Christoph's changes with Bart's changes for 4.12
- a DM bufio unsigned overflow fix
- a couple pure fixes for the DM cache target.
- various very small tweaks to the DM cache target that enable
considerable speed improvements in the face of continuous IO. Given
that the cache target was significantly reworked for 4.12 I see no
reason to sit on these advances until 4.13 considering the favorable
results associated with such minimalist tweaks.
* tag 'for-4.12/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache: handle kmalloc failure allocating background_tracker struct
dm bufio: make the parameter "retain_bytes" unsigned long
dm mpath: multipath_clone_and_map must not return -EIO
dm mpath: don't return -EIO from dm_report_EIO
dm rq: add a missing break to map_request
dm space map disk: fix some book keeping in the disk space map
dm thin metadata: call precommit before saving the roots
dm cache policy smq: don't do any writebacks unless IDLE
dm cache: simplify the IDLE vs BUSY state calculation
dm cache: track all IO to the cache rather than just the origin device's IO
dm cache policy smq: stop preemptively demoting blocks
dm cache policy smq: put newly promoted entries at the top of the multiqueue
dm cache policy smq: be more aggressive about triggering a writeback
dm cache policy smq: only demote entries in bottom half of the clean multiqueue
dm cache: fix incorrect 'idle_time' reset in IO tracker
Linus Torvalds [Wed, 17 May 2017 21:13:44 +0000 (14:13 -0700)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here are some bugfixes from I2C, especially removing a wrongly
displayed error message for all i2c muxes"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: xgene: Set ACPI_COMPANION_I2C
i2c: mv64xxx: don't override deferred probing when getting irq
i2c: mux: only print failure message on error
i2c: mux: reg: rename label to indicate what it does
i2c: mux: reg: put away the parent i2c adapter on probe failure
David S. Miller [Wed, 17 May 2017 20:27:52 +0000 (16:27 -0400)]
Merge branch 'phy-marvell-cleanups'
Andrew Lunn says:
====================
net: phy: marvell: Checkpatch cleanup
I will be contributing a few new features to the Marvell PHY driver
soon. Start by making the code mostly checkpatch clean. There should
not be any functional changes. Just comments set into the correct
format, missing blank lines, turn some comparisons around, and
refactoring to reduce indentation depth.
There is still one camel in the code, but it actually makes sense, so
leave it in piece.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 17 May 2017 01:26:04 +0000 (03:26 +0200)]
net: phy: marvell: checkpatch - Fix remaining long lines
Fold lines longer than 80 characters
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 17 May 2017 01:26:03 +0000 (03:26 +0200)]
net: phy: marvell: Add helpers to get/set page
Makes the code a bit more readable, and solves quite a few checkpatch
warnings of lines longer than 80 characters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 17 May 2017 01:26:02 +0000 (03:26 +0200)]
net: phy: marvell: Refactor some bigger functions
Break big functions up by using a number of smaller helper
function. Solves some of the over 80 lines warnings, by reducing the
indentation level.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 17 May 2017 01:26:01 +0000 (03:26 +0200)]
net: phy: marvell: Checkpatch - assignments and comparisons
Avoid multiple assignments
Comparisons should place the constant on the right side of the test
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 17 May 2017 01:26:00 +0000 (03:26 +0200)]
net: phy: marvell: Checkpatch - Missing or extra blank lines
Remove the extra blank lines, add one in where recommended.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 17 May 2017 01:25:59 +0000 (03:25 +0200)]
net: phy: Marvell: checkpatch - Comments
Use net style comment blocks, and wrap one block with long lines.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 17 May 2017 20:06:03 +0000 (16:06 -0400)]
Merge branch 'tcp-TCP-TS-option-use-1-ms-clock'
Eric Dumazet says:
====================
tcp: TCP TS option use 1 ms clock
TCP Timestamps option is defined in RFC 7323
Traditionally on linux, it has been tied to the internal
'jiffy' variable, because it had been a cheap and good enough
generator.
Unfortunately some distros use HZ=250 or even HZ=100 leading
to not very useful TCP timestamps.
For TCP flows in the DC, Google has used usec resolution for more
than two years with great success [1].
RCVBUF autotuning is more precise.
This series converts tp->tcp_mstamp to a plain u64 value storing
a 1 usec TCP clock.
This choice will allow us to upstream the 1 usec TS option as
discussed in IETF 97.
Kathleen Nichols [2] and others advocate for 1ms TS clocks for
network analysis. (1ms being the lowest value supported by RFC 7323.)
[1] https://www.ietf.org/proceedings/97/slides/slides-97-tcpm-tcp-options-for-low-latency-00.pdf
[2] http://netseminar.stanford.edu/seminars/02_02_17.pdf
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 16 May 2017 21:00:14 +0000 (14:00 -0700)]
tcp: switch TCP TS option (RFC 7323) to 1ms clock
TCP Timestamps option is defined in RFC 7323
Traditionally on linux, it has been tied to the internal
'jiffies' variable, because it had been a cheap and good enough
generator.
For TCP flows on the Internet, 1 ms resolution would be much better
than 4ms or 10ms (HZ=250 or HZ=100 respectively)
For TCP flows in the DC, Google has used usec resolution for more
than two years with great success [1]
Receive size autotuning (DRS) is indeed more precise and converges
faster to optimal window size.
This patch converts tp->tcp_mstamp to a plain u64 value storing
a 1 usec TCP clock.
This choice will allow us to upstream the 1 usec TS option as
discussed in IETF 97.
[1] https://www.ietf.org/proceedings/97/slides/slides-97-tcpm-tcp-options-for-low-latency-00.pdf
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>