OSDN Git Service
YueHaibing [Sat, 26 Oct 2019 02:51:09 +0000 (02:51 +0000)]
net: aquantia: remove unused including <linux/version.h>
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mao Wenan [Sat, 26 Oct 2019 02:21:39 +0000 (10:21 +0800)]
net: dsa: LAN9303: select REGMAP when LAN9303 enable
When NET_DSA_SMSC_LAN9303=y and NET_DSA_SMSC_LAN9303_MDIO=y,
below errors can be seen:
drivers/net/dsa/lan9303_mdio.c:87:23: error: REGMAP_ENDIAN_LITTLE
undeclared here (not in a function)
.reg_format_endian = REGMAP_ENDIAN_LITTLE,
drivers/net/dsa/lan9303_mdio.c:93:3: error: const struct regmap_config
has no member named reg_read
.reg_read = lan9303_mdio_read,
It should select REGMAP in config NET_DSA_SMSC_LAN9303.
Fixes:
dc7005831523 ("net: dsa: LAN9303: add MDIO managed mode support")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mao Wenan [Sat, 26 Oct 2019 02:07:38 +0000 (10:07 +0800)]
net: aquantia: make two symbols be static
When using ARCH=mips CROSS_COMPILE=mips-linux-gnu-
to build drivers/net/ethernet/aquantia/atlantic/aq_ptp.o
and drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_b0.o,
below errors can be seen:
drivers/net/ethernet/aquantia/atlantic/aq_ptp.c:1378:6:
warning: symbol 'aq_ptp_poll_sync_work_cb' was not declared.
Should it be static?
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_b0.c:1155:5:
warning: symbol 'hw_atl_b0_ts_to_sys_clock' was not declared.
Should it be static?
This patch to make aq_ptp_poll_sync_work_cb and hw_atl_b0_ts_to_sys_clock
be static to fix these warnings.
Fixes:
9c477032f7d0 ("net: aquantia: add support for PIN funcs")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 29 Oct 2019 23:08:54 +0000 (16:08 -0700)]
Merge branch '40GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2019-10-25
This series contains updates to i40e only. Several are fixes that could
go to 'net', but were intended for 'net-next'.
Sylwia changes how the driver function to read the NVM module data, so
that it is able to read the LLDP agent configuration to allow for
persistent LLDP.
Jaroslaw resolves an issue where the incorrect FEC settings were being
displayed in ethtool, by setting the proper FEC bits.
Piotr moves the hardware flags detection into a separate function, so
that the specific flags can be set based on the MAC and NVM. Also
extends the PHY access function to include a command flag to let the
firmware know it should not change the page while accessing a OSFP module.
Updates the driver to display the driver and firmware version when in
recovery mode.
Aleksandr refactored the VF MAC filters accounting since an untrusted
VF was able to delete but not add a MAC filter, so refactor the code to
have more consistency and improved logging.
Nicholas updates the driver to use a default interval of 50 usecs,
instead of the current 100 usecs which was causing some regression
performance issues.
Damian resolved LED blinking issues for X710T*L devices by adding
specific flows for these devices in the LED operations.
Navid Emamdoost found where allocated memory is not being properly freed
upon a failure in setting up MAC VLANs, so added the missing kfree().
v2: Dropped patches 2 & 6 from the original series while we wait for the
author to respond to community feedback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 25 Oct 2019 17:22:55 +0000 (18:22 +0100)]
net: fec: remove redundant assignment to pointer bdp
The pointer bdp is being assigned with a value that is never
read, so the assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 25 Oct 2019 18:48:53 +0000 (14:48 -0400)]
net: dsa: return directly from dsa_to_port
Return directly from within the loop as soon as the port is found,
otherwise we won't return NULL if the end of the list is reached.
Fixes:
b96ddf254b09 ("net: dsa: use ports list in dsa_to_port")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 25 Oct 2019 11:58:11 +0000 (12:58 +0100)]
net: aquantia: fix unintention integer overflow on left shift
Shifting the integer value 1 is evaluated using 32-bit
arithmetic and then used in an expression that expects a 64-bit
value, so there is potentially an integer overflow. Fix this
by using the BIT_ULL macro to perform the shift and avoid the
overflow.
Addresses-Coverity: ("Unintentional integer overflow")
Fixes:
04a1839950d9 ("net: aquantia: implement data PTP datapath")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 25 Oct 2019 11:38:28 +0000 (12:38 +0100)]
net: aquantia: fix spelling mistake: tx_queus -> tx_queues
There is a spelling mistake in a netdev_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Fri, 25 Oct 2019 09:30:30 +0000 (17:30 +0800)]
atm: remove unneeded semicolon
remove unneeded semicolon.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Fri, 25 Oct 2019 09:18:36 +0000 (17:18 +0800)]
sock: remove unneeded semicolon
remove unneeded semicolon.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Fri, 25 Oct 2019 09:13:08 +0000 (17:13 +0800)]
net: mediatek: remove unneeded semicolon
remove unneeded semicolon.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Fri, 25 Oct 2019 09:09:48 +0000 (17:09 +0800)]
mlxsw: spectrum_buffers: remove unneeded semicolon
Remove excess semicolon after closing parenthesis.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Oct 2019 23:21:02 +0000 (16:21 -0700)]
Merge branch 'mv88e6xxx-Allow-config-of-ATU-hash-algorithm'
Andrew Lunn says:
====================
mv88e6xxx: Allow config of ATU hash algorithm
v2:
Pass a pointer for where the hash should be stored, return a plain
errno, or 0.
Document the parameter.
v3:
Document type of parameter, and valid range
Add break statements to default clause of switch
Directly use ctx->val.vu8
v4:
Consistently use devlink, not a mix of devlink and dl.
Fix allocation of devlink priv
Remove upper case from parameter name
Make mask 16 bit wide.
v5:
Back to using the parameter name ATU_hash
v6:
Rebase net-next/master
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 24 Oct 2019 23:03:52 +0000 (01:03 +0200)]
net: dsa: mv88e6xxx: Add devlink param for ATU hash algorithm.
Some of the marvell switches have bits controlling the hash algorithm
the ATU uses for MAC addresses. In some industrial settings, where all
the devices are from the same manufacture, and hence use the same OUI,
the default hashing algorithm is not optimal. Allow the other
algorithms to be selected via devlink.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 24 Oct 2019 23:03:51 +0000 (01:03 +0200)]
net: dsa: Add support for devlink device parameters
Add plumbing to allow DSA drivers to register parameters with devlink.
To keep with the abstraction, the DSA drivers pass the ds structure to
these helpers, and the DSA core then translates that to the devlink
structure associated to the device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Thu, 24 Oct 2019 22:30:38 +0000 (00:30 +0200)]
r8169: use helper rtl_hw_aspm_clkreq_enable also in rtl_hw_start_8168g_2
One place in the driver was left where the open-coded functionality
hasn't been replaced with helper rtl_hw_aspm_clkreq_enable yet.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Oct 2019 20:58:20 +0000 (13:58 -0700)]
Merge branch 'net-dsa-b53-Add-support-for-MDB'
Florian Fainelli says:
====================
net: dsa: b53: Add support for MDB
This patch series adds support for programming multicast database
entries on b53 and bcm_sf2. This is extracted from a previously
submitted series that added managed mode support, but these patches are
usable in isolation. The larger series still needs to be reworked.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 24 Oct 2019 19:45:08 +0000 (12:45 -0700)]
net: dsa: bcm_sf2: Wire up MDB operations
Leverage the recently add b53_mdb_{add,del,prepare} functions since they
work as-is for bcm_sf2.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 24 Oct 2019 19:45:07 +0000 (12:45 -0700)]
net: dsa: b53: Add support for MDB
In preparation for supporting IGMP snooping with or without the use of
a bridge, add support within b53_common.c to program the ARL entries for
multicast operations. The key difference is that a multicast ARL entry
is comprised of a bitmask of enabled ports, instead of a port number.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Oct 2019 20:44:26 +0000 (13:44 -0700)]
Merge branch 'mvpp2-improvements-in-rx-path'
Matteo Croce says:
====================
mvpp2 improvements in rx path
Refactor some code in the RX path to allow prefetching some data from the
packet header. The first patch is only a refactor, the second one
reduces the data synced, while the third one adds the prefetch.
The packet rate improvement with the second patch is very small (1606 => 1620 kpps),
while the prefetch bumps it up by 14%: 1620 => 1853 kpps.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo Croce [Thu, 24 Oct 2019 17:24:58 +0000 (19:24 +0200)]
mvpp2: prefetch frame header
When receiving traffic, eth_type_trans() is high up on the perf top list,
because it's the first function which access the packet data.
Move the DMA unmap a bit higher, and put a prefetch just after it, so we
have more time to load the data into the cache.
The packet rate increase is about 14% with a tc drop test: 1620 => 1853 kpps
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo Croce [Thu, 24 Oct 2019 17:24:57 +0000 (19:24 +0200)]
mvpp2: sync only the received frame
In the RX path we always sync against the maximum frame size for that pool.
Do the DMA sync and the unmap separately, so we can only sync by the
size of the received frame.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo Croce [Thu, 24 Oct 2019 17:24:56 +0000 (19:24 +0200)]
mvpp2: refactor frame drop routine
Move some code down to remove a backward goto.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Thu, 24 Oct 2019 15:31:55 +0000 (17:31 +0200)]
isdn: hfcsusb: Spelling and grammar fixes
Fix misspellings of "endpoints", "configuration", and "device's".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Thu, 24 Oct 2019 15:30:43 +0000 (17:30 +0200)]
tipc: Spelling s/enpoint/endpoint/
Fix misspelling of "endpoint".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Thu, 24 Oct 2019 15:23:23 +0000 (17:23 +0200)]
net: Fix various misspellings of "connect"
Fix misspellings of "disconnect", "disconnecting", "connections", and
"disconnected".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Thu, 24 Oct 2019 15:22:01 +0000 (17:22 +0200)]
net: Fix misspellings of "configure" and "configuration"
Fix various misspellings of "configuration" and "configure".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Vokáč [Thu, 24 Oct 2019 13:46:58 +0000 (15:46 +0200)]
net: dsa: qca8k: Initialize the switch with correct number of ports
Since commit
0394a63acfe2 ("net: dsa: enable and disable all ports")
the dsa core disables all unused ports of a switch. In this case
disabling ports with numbers higher than QCA8K_NUM_PORTS causes that
some switch registers are overwritten with incorrect content.
To fix this, initialize the dsa_switch->num_ports with correct number
of ports.
Fixes:
7e99e3470172 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 24 Oct 2019 10:32:18 +0000 (11:32 +0100)]
net: dsa: fix dereference on ds->dev before null check error
Currently ds->dev is dereferenced on the assignments of pdata and
np before ds->dev is null checked, hence there is a potential null
pointer dereference on ds->dev. Fix this by assigning pdata and
np after the ds->dev null pointer sanity check.
Addresses-Coverity: ("Dereference before null check")
Fixes:
7e99e3470172 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 27 Oct 2019 05:57:27 +0000 (22:57 -0700)]
Merge git://git./linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-10-27
The following pull-request contains BPF updates for your *net-next* tree.
We've added 52 non-merge commits during the last 11 day(s) which contain
a total of 65 files changed, 2604 insertions(+), 1100 deletions(-).
The main changes are:
1) Revolutionize BPF tracing by using in-kernel BTF to type check BPF
assembly code. The work here teaches BPF verifier to recognize
kfree_skb()'s first argument as 'struct sk_buff *' in tracepoints
such that verifier allows direct use of bpf_skb_event_output() helper
used in tc BPF et al (w/o probing memory access) that dumps skb data
into perf ring buffer. Also add direct loads to probe memory in order
to speed up/replace bpf_probe_read() calls, from Alexei Starovoitov.
2) Big batch of changes to improve libbpf and BPF kselftests. Besides
others: generalization of libbpf's CO-RE relocation support to now
also include field existence relocations, revamp the BPF kselftest
Makefile to add test runner concept allowing to exercise various
ways to build BPF programs, and teach bpf_object__open() and friends
to automatically derive BPF program type/expected attach type from
section names to ease their use, from Andrii Nakryiko.
3) Fix deadlock in stackmap's build-id lookup on rq_lock(), from Song Liu.
4) Allow to read BTF as raw data from bpftool. Most notable use case
is to dump /sys/kernel/btf/vmlinux through this, from Jiri Olsa.
5) Use bpf_redirect_map() helper in libbpf's AF_XDP helper prog which
manages to improve "rx_drop" performance by ~4%., from Björn Töpel.
6) Fix to restore the flow dissector after reattach BPF test and also
fix error handling in bpf_helper_defs.h generation, from Jakub Sitnicki.
7) Improve verifier's BTF ctx access for use outside of raw_tp, from
Martin KaFai Lau.
8) Improve documentation for AF_XDP with new sections and to reflect
latest features, from Magnus Karlsson.
9) Add back 'version' section parsing to libbpf for old kernels, from
John Fastabend.
10) Fix strncat bounds error in libbpf's libbpf_prog_type_by_name(),
from KP Singh.
11) Turn on -mattr=+alu32 in LLVM by default for BPF kselftests in order
to improve insn coverage for built BPF progs, from Yonghong Song.
12) Misc minor cleanups and fixes, from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Roman Mashak [Sat, 26 Oct 2019 15:11:09 +0000 (11:11 -0400)]
tc-testing: list required kernel options for act_ct action
Updated config with required kernel options for conntrac TC action,
so that tdc can run the tests.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 26 Oct 2019 18:35:43 +0000 (11:35 -0700)]
Merge git://git./linux/kernel/git/pablo/nf-next
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next,
more specifically:
* Updates for ipset:
1) Coding style fix for ipset comment extension, from Jeremy Sowden.
2) De-inline many functions in ipset, from Jeremy Sowden.
3) Move ipset function definition from header to source file.
4) Move ip_set_put_flags() to source, export it as a symbol, remove
inline.
5) Move range_to_mask() to the source file where this is used.
6) Move ip_set_get_ip_port() to the source file where this is used.
* IPVS selftests and netns improvements:
7) Two patches to speedup ipvs netns dismantle, from Haishuang Yan.
8) Three patches to add selftest script for ipvs, also from
Haishuang Yan.
* Conntrack updates and new nf_hook_slow_list() function:
9) Document ct ecache extension, from Florian Westphal.
10) Skip ct extensions from ctnetlink dump, from Florian.
11) Free ct extension immediately, from Florian.
12) Skip access to ecache extension from nf_ct_deliver_cached_events()
this is not correct as reported by Syzbot.
13) Add and use nf_hook_slow_list(), from Florian.
* Flowtable infrastructure updates:
14) Move priority to nf_flowtable definition.
15) Dynamic allocation of per-device hooks in flowtables.
16) Allow to include netdevice only once in flowtable definitions.
17) Rise maximum number of devices per flowtable.
* Netfilter hardware offload infrastructure updates:
18) Add nft_flow_block_chain() helper function.
19) Pass callback list to nft_setup_cb_call().
20) Add nft_flow_cls_offload_setup() helper function.
21) Remove rules for the unregistered device via netdevice event.
22) Support for multiple devices in a basechain definition at the
ingress hook.
22) Add nft_chain_offload_cmd() helper function.
23) Add nft_flow_block_offload_init() helper function.
24) Rewind in case of failing to bind multiple devices to hook.
25) Typo in IPv6 tproxy module description, from Norman Rasmussen.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 26 Oct 2019 18:28:40 +0000 (11:28 -0700)]
Merge branch 'net-aquantia-ptp-followup-fixes'
Igor Russkikh says:
====================
net: aquantia: ptp followup fixes
Here are two sparse warnings, third patch is a fix for
scaled_ppm_to_ppb missing. Eventually I reworked this
to exclude ptp module from build. Please consider it instead
of this patch: https://patchwork.ozlabs.org/patch/
1184171/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Sat, 26 Oct 2019 11:05:34 +0000 (11:05 +0000)]
net: aquantia: disable ptp object build if no config
We do disable aq_ptp module build using inline
stubs when CONFIG_PTP_1588_CLOCK is not declared.
This reduces module size and removes unnecessary code.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Sat, 26 Oct 2019 11:05:33 +0000 (11:05 +0000)]
net: aquantia: fix warnings on endianness
fixes to remove sparse warnings:
sparse: sparse: cast to restricted __be64
Fixes:
04a1839950d9 ("net: aquantia: implement data PTP datapath")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Sat, 26 Oct 2019 11:05:31 +0000 (11:05 +0000)]
net: aquantia: fix var initialization warning
found by sparse, simply useless local initialization with zero.
Fixes:
94ad94558b0f ("net: aquantia: add PTP rings infrastructure")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Thu, 24 Oct 2019 08:30:19 +0000 (10:30 +0200)]
netfilter: nf_tables_offload: unbind if multi-device binding fails
nft_flow_block_chain() needs to unbind in case of error when performing
the multi-device binding.
Fixes:
d54725cd11a5 ("netfilter: nf_tables: support for multiple devices per netdev hook")
Reported-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso [Thu, 24 Oct 2019 08:00:51 +0000 (10:00 +0200)]
netfilter: nf_tables_offload: add nft_flow_block_offload_init()
This patch adds the nft_flow_block_offload_init() helper function to
initialize the flow_block_offload object.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso [Thu, 24 Oct 2019 07:47:08 +0000 (09:47 +0200)]
netfilter: nf_tables_offload: add nft_chain_offload_cmd()
This patch adds the nft_chain_offload_cmd() helper function.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Tue, 22 Oct 2019 16:56:42 +0000 (18:56 +0200)]
netfilter: ecache: don't look for ecache extension on dying/unconfirmed conntracks
syzbot reported following splat:
BUG: KASAN: use-after-free in __nf_ct_ext_exist
include/net/netfilter/nf_conntrack_extend.h:53 [inline]
BUG: KASAN: use-after-free in nf_ct_deliver_cached_events+0x5c3/0x6d0
net/netfilter/nf_conntrack_ecache.c:205
nf_conntrack_confirm include/net/netfilter/nf_conntrack_core.h:65 [inline]
nf_confirm+0x3d8/0x4d0 net/netfilter/nf_conntrack_proto.c:154
[..]
While there is no reproducer yet, the syzbot report contains one
interesting bit of information:
Freed by task 27585:
[..]
kfree+0x10a/0x2c0 mm/slab.c:3757
nf_ct_ext_destroy+0x2ab/0x2e0 net/netfilter/nf_conntrack_extend.c:38
nf_conntrack_free+0x8f/0xe0 net/netfilter/nf_conntrack_core.c:1418
destroy_conntrack+0x1a2/0x270 net/netfilter/nf_conntrack_core.c:626
nf_conntrack_put include/linux/netfilter/nf_conntrack_common.h:31 [inline]
nf_ct_resolve_clash net/netfilter/nf_conntrack_core.c:915 [inline]
^^^^^^^^^^^^^^^^^^^
__nf_conntrack_confirm+0x21ca/0x2830 net/netfilter/nf_conntrack_core.c:1038
nf_conntrack_confirm include/net/netfilter/nf_conntrack_core.h:63 [inline]
nf_confirm+0x3e7/0x4d0 net/netfilter/nf_conntrack_proto.c:154
This is whats happening:
1. a conntrack entry is about to be confirmed (added to hash table).
2. a clash with existing entry is detected.
3. nf_ct_resolve_clash() puts skb->nfct (the "losing" entry).
4. this entry now has a refcount of 0 and is freed to SLAB_TYPESAFE_BY_RCU
kmem cache.
skb->nfct has been replaced by the one found in the hash.
Problem is that nf_conntrack_confirm() uses the old ct:
static inline int nf_conntrack_confirm(struct sk_buff *skb)
{
struct nf_conn *ct = (struct nf_conn *)skb_nfct(skb);
int ret = NF_ACCEPT;
if (ct) {
if (!nf_ct_is_confirmed(ct))
ret = __nf_conntrack_confirm(skb);
if (likely(ret == NF_ACCEPT))
nf_ct_deliver_cached_events(ct); /* This ct has refcount 0! */
}
return ret;
}
As of "netfilter: conntrack: free extension area immediately", we can't
access conntrack extensions in this case.
To fix this, make sure we check the dying bit presence before attempting
to get the eache extension.
Reported-by: syzbot+c7aabc9fe93e7f3637ba@syzkaller.appspotmail.com
Fixes:
2ad9d7747c10d1 ("netfilter: conntrack: free extension area immediately")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David S. Miller [Sat, 26 Oct 2019 03:52:36 +0000 (20:52 -0700)]
Merge branch 'ionic-updates'
Shannon Nelson says:
====================
ionic updates
These are a few of the driver updates we've been working on internally.
These clean up a few mismatched struct comments, add checking for dead
firmware, fix an initialization bug, and change the Rx buffer management.
These are based on net-next
v5.4-rc3-709-g985fd98ab5cc.
v2: clear napi->skb in the error case in ionic_rx_frags()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Thu, 24 Oct 2019 00:49:00 +0000 (17:49 -0700)]
ionic: update driver version
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Thu, 24 Oct 2019 00:48:59 +0000 (17:48 -0700)]
ionic: implement support for rx sgl
Even out Rx performance across MTU sizes by changing from full
skb allocations to page-based frag allocations. The device
supports a form of scatter-gather in the Rx path, so we can
set up a number of pages for each descriptor, all of which are
easier to alloc and pass around than the standard kzalloc'd
buffer. An skb is wrapped around the pages while processing
the received packets, and pages are recycled as needed, or
left alone if they weren't used in the Rx.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Thu, 24 Oct 2019 00:48:58 +0000 (17:48 -0700)]
ionic: add a watchdog timer to monitor heartbeat
Add a watchdog to periodically monitor the NIC heartbeat.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Thu, 24 Oct 2019 00:48:57 +0000 (17:48 -0700)]
ionic: add heartbeat check
Most of our firmware has a heartbeat feature that the driver
can watch for to see if the FW is still alive and likely to
answer a dev_cmd or AdminQ request.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Thu, 24 Oct 2019 00:48:56 +0000 (17:48 -0700)]
ionic: reverse an interrupt coalesce calculation
Fix the initial interrupt coalesce usec-to-hw setting
to actually be usec-to-hw.
Fixes:
780eded34ccc ("ionic: report users coalesce request")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Thu, 24 Oct 2019 00:48:55 +0000 (17:48 -0700)]
ionic: fix up struct name comments
Fix up struct names in the ionic_if.h comments
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 23 Oct 2019 19:36:14 +0000 (21:36 +0200)]
r8169: improve rtl8169_rx_fill
We have only one user of the error path, so we can inline it.
In addition the call to rtl8169_make_unusable_by_asic() can be removed
because rtl8169_alloc_rx_data() didn't call rtl8169_mark_to_asic() yet
for the respective index if returning NULL.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 23 Oct 2019 19:09:34 +0000 (21:09 +0200)]
r8169: align fix_features callback with vendor driver
This patch aligns the fix_features callback with the vendor driver and
also disables IPv6 HW checksumming and TSO if jumbo packets are used
on RTL8101/RTL8168/RTL8125.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 26 Oct 2019 03:19:44 +0000 (20:19 -0700)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-10-23
Here's the main bluetooth-next pull request for the 5.5 kernel:
- Multiple fixes to hci_qca driver
- Fix for HCI_USER_CHANNEL initialization
- btwlink: drop superseded driver
- Add support for Intel FW download error recovery
- Various other smaller fixes & improvements
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Baron [Wed, 23 Oct 2019 15:09:26 +0000 (11:09 -0400)]
tcp: add TCP_INFO status for failed client TFO
The TCPI_OPT_SYN_DATA bit as part of tcpi_options currently reports whether
or not data-in-SYN was ack'd on both the client and server side. We'd like
to gather more information on the client-side in the failure case in order
to indicate the reason for the failure. This can be useful for not only
debugging TFO, but also for creating TFO socket policies. For example, if
a middle box removes the TFO option or drops a data-in-SYN, we can
can detect this case, and turn off TFO for these connections saving the
extra retransmits.
The newly added tcpi_fastopen_client_fail status is 2 bits and has the
following 4 states:
1) TFO_STATUS_UNSPEC
Catch-all state which includes when TFO is disabled via black hole
detection, which is indicated via LINUX_MIB_TCPFASTOPENBLACKHOLE.
2) TFO_COOKIE_UNAVAILABLE
If TFO_CLIENT_NO_COOKIE mode is off, this state indicates that no cookie
is available in the cache.
3) TFO_DATA_NOT_ACKED
Data was sent with SYN, we received a SYN/ACK but it did not cover the data
portion. Cookie is not accepted by server because the cookie may be invalid
or the server may be overloaded.
4) TFO_SYN_RETRANSMITTED
Data was sent with SYN, we received a SYN/ACK which did not cover the data
after at least 1 additional SYN was sent (without data). It may be the case
that a middle-box is dropping data-in-SYN packets. Thus, it would be more
efficient to not use TFO on this connection to avoid extra retransmits
during connection establishment.
These new fields do not cover all the cases where TFO may fail, but other
failures, such as SYN/ACK + data being dropped, will result in the
connection not becoming established. And a connection blackhole after
session establishment shows up as a stalled connection.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Christoph Paasch <cpaasch@apple.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 26 Oct 2019 02:24:47 +0000 (19:24 -0700)]
Merge branch 'phy-dp83867-enable-robust-auto-mdix'
Grygorii Strashko says:
====================
net: phy: dp83867: enable robust auto-mdix
Patch 1 - improves link detection when dp83867 PHY is configured in manual mode
by enabling CFG3[9] Robust Auto-MDIX option.
Patch 2 - is minor optimization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Wed, 23 Oct 2019 14:48:46 +0000 (17:48 +0300)]
net: phy: dp83867: move dt parsing to probe
Move DT parsing code to probe dp83867_probe() as it's one time operation.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Wed, 23 Oct 2019 14:48:45 +0000 (17:48 +0300)]
net: phy: dp83867: enable robust auto-mdix
The link detection timeouts can be observed (or link might not be detected
at all) when dp83867 PHY is configured in manual mode (speed/duplex).
CFG3[9] Robust Auto-MDIX option allows to significantly improve link detection
in case dp83867 is configured in manual mode and reduce link detection
time.
As per DM: "If link partners are configured to operational modes that are
not supported by normal Auto MDI/MDIX mode (like Auto-Neg versus Force
100Base-TX or Force 100Base-TX versus Force 100Base-TX), this Robust Auto
MDI/MDIX mode allows MDI/MDIX resolution and prevents deadlock."
Hence, enable this option by default as there are no known reasons
not to do so.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Prince [Wed, 23 Oct 2019 13:44:20 +0000 (15:44 +0200)]
net: sch_generic: Use pfifo_fast as fallback scheduler for CAN hardware
There is networking hardware that isn't based on Ethernet for layers 1 and 2.
For example CAN.
CAN is a multi-master serial bus standard for connecting Electronic Control
Units [ECUs] also known as nodes. A frame on the CAN bus carries up to 8 bytes
of payload. Frame corruption is detected by a CRC. However frame loss due to
corruption is possible, but a quite unusual phenomenon.
While fq_codel works great for TCP/IP, it doesn't for CAN. There are a lot of
legacy protocols on top of CAN, which are not build with flow control or high
CAN frame drop rates in mind.
When using fq_codel, as soon as the queue reaches a certain delay based length,
skbs from the head of the queue are silently dropped. Silently meaning that the
user space using a send() or similar syscall doesn't get an error. However
TCP's flow control algorithm will detect dropped packages and adjust the
bandwidth accordingly.
When using fq_codel and sending raw frames over CAN, which is the common use
case, the user space thinks the package has been sent without problems, because
send() returned without an error. pfifo_fast will drop skbs, if the queue
length exceeds the maximum. But with this scheduler the skbs at the tail are
dropped, an error (-ENOBUFS) is propagated to user space. So that the user
space can slow down the package generation.
On distributions, where fq_codel is made default via CONFIG_DEFAULT_NET_SCH
during compile time, or set default during runtime with sysctl
net.core.default_qdisc (see [1]), we get a bad user experience. In my test case
with pfifo_fast, I can transfer thousands of million CAN frames without a frame
drop. On the other hand with fq_codel there is more then one lost CAN frame per
thousand frames.
As pointed out fq_codel is not suited for CAN hardware, so this patch changes
attach_one_default_qdisc() to use pfifo_fast for "ARPHRD_CAN" network devices.
During transition of a netdev from down to up state the default queuing
discipline is attached by attach_default_qdiscs() with the help of
attach_one_default_qdisc(). This patch modifies attach_one_default_qdisc() to
attach the pfifo_fast (pfifo_fast_ops) if the network device type is
"ARPHRD_CAN".
[1] https://github.com/systemd/systemd/issues/9194
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Vincent Prince <vincent.prince.fr@gmail.com>
Acked-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang [Wed, 23 Oct 2019 13:24:44 +0000 (21:24 +0800)]
r8152: check the pointer rtl_fw->fw before using it
Fix the pointer rtl_fw->fw would be used before checking in
rtl8152_apply_firmware() that causes the following kernel oops.
Unable to handle kernel NULL pointer dereference at virtual address
00000002
pgd = (ptrval)
[
00000002] *pgd=
00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 131 Comm: kworker/0:2 Not tainted
5.4.0-rc1-00539-g9370f2d05a2a #6788
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events_long rtl_hw_phy_work_func_t
PC is at rtl8152_apply_firmware+0x14/0x464
LR is at r8153_hw_phy_cfg+0x24/0x17c
pc : [<
c064f4e4>] lr : [<
c064fa18>] psr:
a0000013
sp :
e75c9e60 ip :
60000013 fp :
c11b7614
r10:
e883b91c r9 :
00000000 r8 :
fffffffe
r7 :
e883b640 r6 :
fffffffe r5 :
fffffffe r4 :
e883b640
r3 :
736cfe7c r2 :
736cfe7c r1 :
000052f8 r0 :
e883b640
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control:
10c5387d Table:
6640006a DAC:
00000051
Process kworker/0:2 (pid: 131, stack limit = 0x(ptrval))
Stack: (0xe75c9e60 to 0xe75ca000)
...
[<
c064f4e4>] (rtl8152_apply_firmware) from [<
c064fa18>]
(r8153_hw_phy_cfg+0x24/0x17c)
[<
c064fa18>] (r8153_hw_phy_cfg) from [<
c064e784>]
(rtl_hw_phy_work_func_t+0x220/0x3e4)
[<
c064e784>] (rtl_hw_phy_work_func_t) from [<
c0148a74>]
(process_one_work+0x22c/0x7c8)
[<
c0148a74>] (process_one_work) from [<
c0149054>] (worker_thread+0x44/0x520)
[<
c0149054>] (worker_thread) from [<
c0150548>] (kthread+0x130/0x164)
[<
c0150548>] (kthread) from [<
c01010b4>] (ret_from_fork+0x14/0x20)
Exception stack(0xe75c9fb0 to 0xe75c9ff8)
...
Fixes:
9370f2d05a2a ("r8152: support request_firmware for RTL8153")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrii Nakryiko [Fri, 25 Oct 2019 04:55:03 +0000 (21:55 -0700)]
selftests/bpf: Fix .gitignore to ignore no_alu32/
When switching to alu32 by default, no_alu32/ subdirectory wasn't added
to .gitignore. Fix it.
Fixes:
e13a2fe642bd ("tools/bpf: Turn on llvm alu32 attribute by default")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20191025045503.3043427-1-andriin@fb.com
Jiri Olsa [Thu, 24 Oct 2019 13:30:25 +0000 (15:30 +0200)]
bpftool: Allow to read btf as raw data
The bpftool interface stays the same, but now it's possible
to run it over BTF raw data, like:
$ bpftool btf dump file /sys/kernel/btf/vmlinux
[1] INT '(anon)' size=4 bits_offset=0 nr_bits=32 encoding=(none)
[2] INT 'long unsigned int' size=8 bits_offset=0 nr_bits=64 encoding=(none)
[3] CONST '(anon)' type_id=2
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Link: https://lore.kernel.org/bpf/20191024133025.10691-1-jolsa@kernel.org
Navid Emamdoost [Wed, 25 Sep 2019 15:48:30 +0000 (10:48 -0500)]
i40e: prevent memory leak in i40e_setup_macvlans
In i40e_setup_macvlans if i40e_setup_channel fails the allocated memory
for ch should be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Aleksandr Loktionov [Fri, 20 Sep 2019 09:17:24 +0000 (02:17 -0700)]
i40e: Refactoring VF MAC filters counting to make more reliable
This patch prepares ground for the next VF MAC address change fix.
It lets untrusted VF to delete any VF mac filter, but it still
doesn't let untrusted VF to add mac filter not setup by PF.
It removes information duplication in num_mac mac filters counter.
And improves exact h/w mac filters usage checking in the
i40e_check_vf_permission() function by counting mac2add_cnt.
It also improves logging because now all mac addresses will be validated
first and corresponding messages will be logged.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Damian Milosek [Fri, 20 Sep 2019 09:17:23 +0000 (02:17 -0700)]
i40e: Fix LED blinking flow for X710T*L devices
Add X710T*L device specific operations (in port LED detection and
handling of GLGEN_GPIO_CTL.PIN_FUNC field) to enable LED blinking.
Signed-off-by: Damian Milosek <damian.milosek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Piotr Kwapulinski [Fri, 20 Sep 2019 09:17:22 +0000 (02:17 -0700)]
i40e: allow ethtool to report SW and FW versions in recovery mode
Let ethtool print driver and firmware versions when NIC is in
recovery mode. Assign i40e_get_drvinfo() operation to ethtool
recovery mode operations. Previously ethtool did not report
driver and firmware versions when NIC was in recovery mode.
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Nicholas Nunley [Fri, 20 Sep 2019 09:17:21 +0000 (02:17 -0700)]
i40e: initialize ITRN registers with correct values
Since commit
92418fb14750 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN/ITR0 registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.
Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.
This patch adds the correct conversion when writing the initial values to
the ITRN registers.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Piotr Azarewicz [Fri, 20 Sep 2019 09:17:19 +0000 (02:17 -0700)]
i40e: Extend PHY access with page change flag
Currently FW use MDIO I/F number corresponded with current PF for PHY
access. This code allow to specify used MDIO I/F number.
Add new field - command flags with only one flag for now. Added flag
tells FW that it shouldn't change page while accessing QSFP module, as
it was set manually.
Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Piotr Azarewicz [Fri, 20 Sep 2019 09:17:18 +0000 (02:17 -0700)]
i40e: Extract detection of HW flags into a function
Move code detecting HW flags based on device type and FW API version
into a single function.
Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jaroslaw Gawin [Fri, 20 Sep 2019 09:17:17 +0000 (02:17 -0700)]
i40e: Wrong 'Advertised FEC modes' after set FEC to AUTO
Fix display of parameters "Configured FEC encodings:" and "Advertised
FEC modes:" in ethtool. Implemented by setting proper FEC bits in
“advertising” bitmask of link_modes struct and “fec” bitmask in
ethtool_fecparam struct. Without this patch wrong FEC settings
can be shown.
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sylwia Wnuczko [Fri, 20 Sep 2019 09:17:15 +0000 (02:17 -0700)]
i40e: Fix for persistent lldp support
This patch fixes function to read NVM module data and uses it to
read current LLDP agent configuration from NVM API version 1.8.
Signed-off-by: Sylwia Wnuczko <sylwia.wnuczko@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Martin KaFai Lau [Fri, 25 Oct 2019 00:18:11 +0000 (17:18 -0700)]
bpf: Prepare btf_ctx_access for non raw_tp use case
This patch makes a few changes to btf_ctx_access() to prepare
it for non raw_tp use case where the attach_btf_id is not
necessary a BTF_KIND_TYPEDEF.
It moves the "btf_trace_" prefix check and typedef-follow logic to a new
function "check_attach_btf_id()" which is called only once during
bpf_check(). btf_ctx_access() only operates on a BTF_KIND_FUNC_PROTO
type now. That should also be more efficient since it is done only
one instead of every-time check_ctx_access() is called.
"check_attach_btf_id()" needs to find the func_proto type from
the attach_btf_id. It needs to store the result into the
newly added prog->aux->attach_func_proto. func_proto
btf type has no name, so a proper name should be stored into
"attach_func_name" also.
v2:
- Move the "btf_trace_" check to an earlier verifier phase (Alexei)
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191025001811.1718491-1-kafai@fb.com
David S. Miller [Thu, 24 Oct 2019 22:21:58 +0000 (15:21 -0700)]
Merge branch 'DPAA-Ethernet-changes'
Madalin Bucur says:
====================
DPAA Ethernet changes
v3: add newline at the end of error messages
v2: resending with From: field matching signed-off-by
Here's a series of changes for the DPAA Ethernet, addressing minor
or unapparent issues in the codebase, adding probe ordering based on
a recently added DPAA QMan API, removing some redundant code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Wed, 23 Oct 2019 09:08:46 +0000 (12:08 +0300)]
dpaa_eth: add newline in dev_err() msg
Newline was missing at the end of the error message.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Wed, 23 Oct 2019 09:08:45 +0000 (12:08 +0300)]
fsl/fman: remove unused struct member
Remove unused struct member second_largest_buf_size. Also, an out of
bounds access would have occurred in the removed code if there was only
one buffer pool in use.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Wed, 23 Oct 2019 09:08:44 +0000 (12:08 +0300)]
dpaa_eth: change DMA device
The DPAA Ethernet driver is using the FMan MAC as the device for DMA
mapping. This is not actually correct, as the real DMA device is the
FMan port (the FMan Rx port for reception and the FMan Tx port for
transmission). Changing the device used for DMA mapping to the Fman
Rx and Tx port devices.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Laurentiu Tudor [Wed, 23 Oct 2019 09:08:43 +0000 (12:08 +0300)]
fsl/fman: add API to get the device behind a fman port
Add an API that retrieves the 'struct device' that the specified FMan
port probed against. The new API will be used in a subsequent patch
that corrects the DMA devices used by the dpaa_eth driver.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Wed, 23 Oct 2019 09:08:42 +0000 (12:08 +0300)]
dpaa_eth: remove redundant code
Condition was previously checked, removing duplicate code.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Laurentiu Tudor [Wed, 23 Oct 2019 09:08:41 +0000 (12:08 +0300)]
dpaa_eth: defer probing after qbman
If the DPAA 1 Ethernet driver gets probed before the QBMan driver it will
cause a boot crash. Add predictability in the probing order by deferring
the Ethernet driver probe after QBMan and portals by using the recently
introduced QBMan APIs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Laurentiu Tudor [Wed, 23 Oct 2019 09:08:40 +0000 (12:08 +0300)]
fsl/fman: don't touch liodn base regs reserved on non-PAMU SoCs
The liodn base registers are specific to PAMU based NXP systems and are
reserved on SMMU based ones. Don't access them unless PAMU is compiled in.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 24 Oct 2019 16:51:23 +0000 (09:51 -0700)]
Merge branch 'net-aquantia-PTP-support-for-AQC-devices'
Igor Russkikh says:
====================
net: aquantia: PTP support for AQC devices
This patchset introduces PTP feature support in Aquantia AQC atlantic driver.
This implementation is a joined effort of aquantia developers:
Egor is the main designer and driver/firmware architect on PTP,
Sergey and Dmitry are included as co-developers.
Dmitry also helped me in the overall patchset preparations.
Feature was verified on AQC hardware with testptp tool, linuxptp,
gptp and with Motu hardware unit.
version3 updates:
- Review comments applied: error handling, various fixes
version2 updates:
- Fixing issues from Andrew's review: replacing self with
ptp var name, making ptp_clk_offset a field in the ptp instance.
devm_kzalloc advice is actually non applicable, because ptp object gets
created/destroyed on each network device close/open and it should not be
linked with dev lifecycle.
- Rearranging commit authorship, adding Egor as a ptp module main maintainer
- Fixing kbuild 32bit division issues
====================
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Tue, 22 Oct 2019 09:53:49 +0000 (09:53 +0000)]
net: aquantia: adding atlantic ptp maintainer
PTP implementation is designed and maintained by Egor Pomozov, adding
him as this module maintainer. Egor is the author of the core
functionality and the architect, and is to be contacted for
all Aquantia PTP/AVB functionality.
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bezrukov [Tue, 22 Oct 2019 09:53:47 +0000 (09:53 +0000)]
net: aquantia: add support for PIN funcs
Depending on FW configuration we can manage from 0 to 3 PINs for periodic output
and from 0 to 1 ext ts PIN for getting TS for external event.
Ext TS PIN functionality is implemented via periodic timestamps polling
directly from PHY, because right now there is now way to receive the
PIN trigger interrupt from phy.
The polling interval is 15 milliseconds.
Co-developed-by: Egor Pomozov <epomozov@marvell.com>
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bezrukov [Tue, 22 Oct 2019 09:53:45 +0000 (09:53 +0000)]
net: aquantia: add support for Phy access
GPIO PIN control and access is done by direct phy manipulation.
Here we add an aq_phy module which is able to access phy registers
via MDIO access mailbox.
Access is controlled via HW semaphore.
Co-developed-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Egor Pomozov [Tue, 22 Oct 2019 09:53:42 +0000 (09:53 +0000)]
net: aquantia: implement get_ts_info ethtool
Ethtool callback with basic information on what PTP features are supported
by the device.
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Egor Pomozov [Tue, 22 Oct 2019 09:53:40 +0000 (09:53 +0000)]
net: aquantia: add support for ptp ioctls
Here we add support for PTP specific IOCTLs of HW timestamp get/set.
These will use filters to configure flows onto the required queue ids.
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bezrukov [Tue, 22 Oct 2019 09:53:38 +0000 (09:53 +0000)]
net: aquantia: rx filters for ptp
We implement HW filter reservation for PTP traffic. Special location
in filters table is marked as reserved, because incoming ptp traffic
should be directed only to PTP designated queue. This way HW will do PTP
timestamping and proper processing.
Co-developed-by: Egor Pomozov <epomozov@marvell.com>
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Egor Pomozov [Tue, 22 Oct 2019 09:53:35 +0000 (09:53 +0000)]
net: aquantia: implement data PTP datapath
Here we do alloc/free IRQs for PTP rings.
We also implement processing of PTP packets on TX and RX sides.
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bezrukov [Tue, 22 Oct 2019 09:53:32 +0000 (09:53 +0000)]
net: aquantia: styling fixes on ptp related functions
Checkpatch and styling fixes on parts of code touched by ptp
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Egor Pomozov [Tue, 22 Oct 2019 09:53:29 +0000 (09:53 +0000)]
net: aquantia: add PTP rings infrastructure
Add implementations of PTP rings alloc/free.
PTP desing on this device uses two separate rings on a separate traffic
class for traffic rx/tx.
Third ring (hwts) is not a traffic ring, but is used only to receive timestamps
of the transmitted packets.
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Egor Pomozov [Tue, 22 Oct 2019 09:53:27 +0000 (09:53 +0000)]
net: aquantia: add basic ptp_clock callbacks
Basic HW functions implemented for adjusting frequency,
adjusting time, getting and setting time.
With these callbacks we now do register ptp clock in the system.
Firmware interface parts are defined for PTP requests and interactions.
Enable/disable PTP counters in HW on clock register/unregister.
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bezrukov [Tue, 22 Oct 2019 09:53:25 +0000 (09:53 +0000)]
net: aquantia: unify styling of bit enums
Make some other bit-enums more clear about positioning,
this helps on debugging and development
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Egor Pomozov [Tue, 22 Oct 2019 09:53:22 +0000 (09:53 +0000)]
net: aquantia: PTP skeleton declarations and callbacks
Here we add basic function for PTP clock register/unregister.
We also declare FW/HW capability bits used to control PTP feature on device.
PTP device is created if network card has appropriate FW that has PTP
enabled in config. HW supports timestamping for PTPv2 802.AS1 and
PTPv2 IPv4 UDP packets.
It also supports basic PTP callbacks for getting/setting time, adjusting
frequency and time as well.
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 23 Oct 2019 07:36:26 +0000 (15:36 +0800)]
net: lan78xx: remove set but not used variable 'event'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/usb/lan78xx.c:3995:6: warning:
variable event set but not used [-Wunused-but-set-variable]
It is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 24 Oct 2019 04:31:31 +0000 (21:31 -0700)]
Merge branch 'mlxsw-Update-main-pool-computation-and-pool-size-limits'
Ido Schimmel says:
====================
mlxsw: Update main pool computation and pool size limits
Petr says:
In Spectrum ASICs, the shared buffer is an area of memory where packets are
kept until they can be transmitted. There are two resources associated with
shared buffer size: cap_total_buffer_size and cap_guaranteed_shared_buffer.
So far, mlxsw has been using the former as a limit when validating shared
buffer pool size configuration. However, the total size also includes
headrooms and reserved space, which really cannot be used for shared buffer
pools. Patch #1 mends this and has mlxsw use the guaranteed size.
To configure default pool sizes, mlxsw has historically hard-coded one or
two smallish pools, and one "main" pool that took most of the shared buffer
(that would be pool 0 on ingress and pool 4 on egress). During the
development of Spectrum-2, it became clear that the shared buffer size
keeps shrinking as bugs are identified and worked around. In order to
prevent having to tweak the size of pools 0 and 4 to catch up with updates
to values reported by the FW, patch #2 changes the way these pools are set.
Instead of hard-coding a fixed value, the main pool now takes whatever is
left from the guaranteed size after the smaller pool(s) are taken into
account.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Wed, 23 Oct 2019 06:05:00 +0000 (09:05 +0300)]
mlxsw: spectrum_buffers: Calculate the size of the main pool
Instead of hard-coding the size of the largest pool, calculate it from the
reported guaranteed shared buffer size and sizes of other pools (currently
only the CPU port pool).
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Wed, 23 Oct 2019 06:04:59 +0000 (09:04 +0300)]
mlxsw: spectrum: Use guaranteed buffer size as pool size limit
There are two resources associated with shared buffer size:
cap_total_buffer_size, and cap_guaranteed_shared_buffer. So far, mlxsw has
been using the former as a limit to determine how large a pool size is
allowed to be. However, the total size also includes headrooms and reserved
space, which really cannot be used for shared buffer pools.
Therefore convert mlxsw to use the latter resource as a limit. Adjust
hard-coded pool sizes to be the guaranteed size minus 256000 bytes for CPU
port pool. On Spectrum-1 that actually leads to an increase. A follow-up
patch will have this size calculated automatically.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Tue, 22 Oct 2019 19:30:57 +0000 (21:30 +0200)]
r8169: never set PCI_EXP_DEVCTL_NOSNOOP_EN
Setting PCI_EXP_DEVCTL_NOSNOOP_EN for certain chip versions had been
added to the vendor driver more than 10 years ago, and copied from
there to r8169. It has been removed from the vendor driver meanwhile
and I think we can safely remove this too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 24 Oct 2019 03:42:53 +0000 (20:42 -0700)]
Merge branch 'net-phy-support-1000Base-X-auto-negotiation-for-BCM54616S'
Tao Ren says:
====================
net: phy: support 1000Base-X auto-negotiation for BCM54616S
This patch series aims at supporting auto negotiation when BCM54616S is
running in 1000Base-X mode: without the patch series, BCM54616S PHY driver
would report incorrect link speed in 1000Base-X mode.
Patch #1 (of 3) modifies assignment to OR when dealing with dev_flags in
phy_attach_direct function, so that dev_flags updated in BCM54616S PHY's
probe callback won't be lost.
Patch #2 (of 3) adds several genphy_c37_* functions to support clause 37
1000Base-X auto-negotiation, and these functions are called in BCM54616S
PHY driver.
Patch #3 (of 3) detects BCM54616S PHY's operation mode and calls according
genphy_c37_* functions to configure auto-negotiation and parse link
attributes (speed, duplex, and etc.) in 1000Base-X mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tao Ren [Tue, 22 Oct 2019 18:31:08 +0000 (11:31 -0700)]
net: phy: broadcom: add 1000Base-X support for BCM54616S
The BCM54616S PHY cannot work properly in RGMII->1000Base-X mode, mainly
because genphy functions are designed for copper links, and 1000Base-X
(clause 37) auto negotiation needs to be handled differently.
This patch enables 1000Base-X support for BCM54616S by customizing 3
driver callbacks, and it's verified to be working on Facebook CMM BMC
platform (RGMII->1000Base-KX):
- probe: probe callback detects PHY's operation mode based on
INTERF_SEL[1:0] pins and 1000X/100FX selection bit in SerDES 100-FX
Control register.
- config_aneg: calls genphy_c37_config_aneg when the PHY is running in
1000Base-X mode; otherwise, genphy_config_aneg will be called.
- read_status: calls genphy_c37_read_status when the PHY is running in
1000Base-X mode; otherwise, genphy_read_status will be called.
Note: BCM54616S PHY can also be configured in RGMII->100Base-FX mode, and
100Base-FX support is not available as of now.
Signed-off-by: Tao Ren <taoren@fb.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Tue, 22 Oct 2019 18:31:07 +0000 (11:31 -0700)]
net: phy: add support for clause 37 auto-negotiation
This patch adds support for clause 37 1000Base-X auto-negotiation.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Tao Ren <taoren@fb.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tao Ren [Tue, 22 Oct 2019 18:31:06 +0000 (11:31 -0700)]
net: phy: modify assignment to OR for dev_flags in phy_attach_direct
Modify the assignment to OR when dealing with phydev->dev_flags in
phy_attach_direct function, and this is to make sure dev_flags set in
driver's probe callback won't be lost.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
CC: Heiner Kallweit <hkallweit1@gmail.com>
CC: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KP Singh [Wed, 23 Oct 2019 15:40:38 +0000 (17:40 +0200)]
libbpf: Fix strncat bounds error in libbpf_prog_type_by_name
On compiling samples with this change, one gets an error:
error: ‘strncat’ specified bound 118 equals destination size
[-Werror=stringop-truncation]
strncat(dst, name + section_names[i].len,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(raw_tp_btf_name) - (dst - raw_tp_btf_name));
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
strncat requires the destination to have enough space for the
terminating null byte.
Fixes:
f75a697e09137 ("libbpf: Auto-detect btf_id of BTF-based raw_tracepoint")
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191023154038.24075-1-kpsingh@chromium.org
Magnus Karlsson [Mon, 21 Oct 2019 08:57:04 +0000 (10:57 +0200)]
xsk: Improve documentation for AF_XDP
Added sections on all the bind flags, libbpf, all the setsockopts and
all the getsockopts. Also updated the document to reflect the latest
features and to correct some spelling errors.
v1 -> v2:
* Updated XDP program with latest BTF map format
* Added one more FAQ entry
* Some minor edits and corrections
v2 -> v3:
* Simplified XDP_SHARED_UMEM example XDP program
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1571648224-16889-1-git-send-email-magnus.karlsson@intel.com