OSDN Git Service
Luiz Augusto von Dentz [Mon, 29 Jul 2019 15:15:43 +0000 (18:15 +0300)]
Bluetooth: Add initial implementation of CIS connections
This adds the initial implementation of CIS connections and introduces
the ISO packets/links.
== Central: Set CIG Parameters, create a CIS and Setup Data Path ==
> tools/isotest -s <address>
< HCI Command: LE Extended Create... (0x08|0x0043) plen 26
...
> HCI Event: Command Status (0x0f) plen 4
LE Extended Create Connection (0x08|0x0043) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 31
LE Enhanced Connection Complete (0x0a)
...
< HCI Command: LE Create Connected... (0x08|0x0064) plen 5
...
> HCI Event: Command Status (0x0f) plen 4
LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 29
LE Connected Isochronous Stream Established (0x19)
...
< HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13
...
> HCI Event: Command Complete (0x0e) plen 6
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
Status: Success (0x00)
Handle: 257
< HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13
...
> HCI Event: Command Complete (0x0e) plen 6
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
Status: Success (0x00)
Handle: 257
== Peripheral: Accept CIS and Setup Data Path ==
> tools/isotest -d
HCI Event: LE Meta Event (0x3e) plen 7
LE Connected Isochronous Stream Request (0x1a)
...
< HCI Command: LE Accept Co.. (0x08|0x0066) plen 2
...
> HCI Event: LE Meta Event (0x3e) plen 29
LE Connected Isochronous Stream Established (0x19)
...
< HCI Command: LE Setup Is.. (0x08|0x006e) plen 13
...
> HCI Event: Command Complete (0x0e) plen 6
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
Status: Success (0x00)
Handle: 257
< HCI Command: LE Setup Is.. (0x08|0x006e) plen 13
...
> HCI Event: Command Complete (0x0e) plen 6
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
Status: Success (0x00)
Handle: 257
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Fri, 4 Feb 2022 21:04:38 +0000 (13:04 -0800)]
Bluetooth: hci_core: Introduce hci_recv_event_data
This introduces hci_recv_event_data to make it simpler to access the
contents of last received event rather than having to pass its contents
to the likes of *_ind/*_cfm callbacks.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Brian Gix [Thu, 21 Jul 2022 23:22:25 +0000 (16:22 -0700)]
Bluetooth: Convert delayed discov_off to hci_sync
The timed ending of Discoverability was handled in hci_requst.c, with
calls using the deprecated hci_req_add() mechanism. Converted to live
inside mgmt.c using the same delayed work queue, but with hci_sync
version of hci_update_discoverable().
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Brian Gix [Thu, 21 Jul 2022 23:22:24 +0000 (16:22 -0700)]
Bluetooth: Remove update_scan hci_request dependancy
This removes the remaining calls to HCI_OP_WRITE_SCAN_ENABLE from
hci_request call chains, and converts them to hci_sync calls.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Brian Gix [Thu, 21 Jul 2022 23:22:23 +0000 (16:22 -0700)]
Bluetooth: Remove dead code from hci_request.c
The discov_update work queue is no longer used as a result
of the hci_sync rework.
The __hci_req_hci_power_on() function is no longer referenced in the
code as a result of the hci_sync rework.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
shaomin Deng [Wed, 20 Jul 2022 14:10:33 +0000 (10:10 -0400)]
Bluetooth: btrtl: Fix typo in comment
Delete the repeated word "that" in comments.
Signed-off-by: shaomin Deng <dengshaomin@cdjrlc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Thu, 21 Jul 2022 22:56:28 +0000 (15:56 -0700)]
Bluetooth: MGMT: Fix holding hci_conn reference while command is queued
This removes the use of hci_conn_hold from Get Conn Info and Get Clock
Info since the callback can just do a lookup by address using the cmd
data and only then set cmd->user_data to pass to the complete callback.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Tue, 21 Jun 2022 18:58:34 +0000 (11:58 -0700)]
Bluetooth: mgmt: Fix using hci_conn_abort
This fixes using hci_conn_abort instead of using hci_conn_abort_sync.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Wed, 4 May 2022 23:49:17 +0000 (16:49 -0700)]
Bluetooth: Use bt_status to convert from errno
If a command cannot be sent or there is a internal error an errno maybe
set instead of a command status.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Fri, 8 Apr 2022 22:07:44 +0000 (15:07 -0700)]
Bluetooth: Add bt_status
This adds bt_status which can be used to convert Unix errno to
Bluetooth status.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Fri, 1 Apr 2022 23:12:27 +0000 (16:12 -0700)]
Bluetooth: hci_sync: Split hci_dev_open_sync
This splits hci_dev_open_sync so each stage is handle by its own
function so it is easier to identify each stage.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Manish Mandlik [Wed, 20 Jul 2022 23:21:14 +0000 (16:21 -0700)]
Bluetooth: hci_sync: Refactor remove Adv Monitor
Make use of hci_cmd_sync_queue for removing an advertisement monitor.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Miao-chen Chou <mcchou@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Manish Mandlik [Wed, 20 Jul 2022 23:21:13 +0000 (16:21 -0700)]
Bluetooth: hci_sync: Refactor add Adv Monitor
Make use of hci_cmd_sync_queue for adding an advertisement monitor.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Miao-chen Chou <mcchou@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Zijun Hu [Thu, 21 Jul 2022 06:04:33 +0000 (14:04 +0800)]
Bluetooth: hci_sync: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING
Core driver addtionally checks LMP feature bit "Erroneous Data Reporting"
instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so
remove this unnecessary quirk.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Zijun Hu [Thu, 21 Jul 2022 06:04:32 +0000 (14:04 +0800)]
Bluetooth: btusb: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for fake CSR
Core driver addtionally checks LMP feature bit "Erroneous Data Reporting"
instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so
remove this unnecessary quirk for fake CSR controllers.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Zijun Hu [Thu, 21 Jul 2022 06:04:31 +0000 (14:04 +0800)]
Bluetooth: btusb: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for QCA
Core driver addtionally checks LMP feature bit "Erroneous Data Reporting"
instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so
remove this unnecessary quirk for QCA controllers.
The reason why these two HCI commands are broken for QCA controllers is
that feature "Erroneous Data Reporting" is not enabled by their firmware
as shown by below log:
@ RAW Open: hcitool (privileged) version 2.22
< HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0
> HCI Event: Command Complete (0x0e) plen 68
Read Local Supported Commands (0x04|0x0002) ncmd 1
Status: Success (0x00)
Commands: 288 entries
......
Read Default Erroneous Data Reporting (Octet 18 - Bit 2)
Write Default Erroneous Data Reporting (Octet 18 - Bit 3)
......
< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
> HCI Event: Command Complete (0x0e) plen 4
Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1
Status: Unknown HCI Command (0x01)
< HCI Command: Read Local Supported Features (0x04|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Supported Features (0x04|0x0003) ncmd 1
Status: Success (0x00)
Features: 0xff 0xfe 0x0f 0xfe 0xd8 0x3f 0x5b 0x87
3 slot packets
......
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Zijun Hu [Thu, 21 Jul 2022 06:04:30 +0000 (14:04 +0800)]
Bluetooth: hci_sync: Check LMP feature bit instead of quirk
BT core driver should addtionally check LMP feature bit
"Erroneous Data Reporting" instead of quirk
HCI_QUIRK_BROKEN_ERR_DATA_REPORTING set by BT device driver to decide if
HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken.
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 2, Part C | page 587
This feature indicates whether the device is able to support the
Packet_Status_Flag and the HCI commands HCI_Write_Default_-
Erroneous_Data_Reporting and HCI_Read_Default_Erroneous_-
Data_Reporting.
the quirk was introduced by 'commit
cde1a8a99287 ("Bluetooth: btusb: Fix
and detect most of the Chinese Bluetooth controllers")' to mark HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting broken by BT
device driver, but the reason why these two HCI commands are broken is
that feature "Erroneous Data Reporting" is not enabled by firmware, this
scenario is illustrated by below log of QCA controllers with USB I/F:
@ RAW Open: hcitool (privileged) version 2.22
< HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0
> HCI Event: Command Complete (0x0e) plen 68
Read Local Supported Commands (0x04|0x0002) ncmd 1
Status: Success (0x00)
Commands: 288 entries
......
Read Default Erroneous Data Reporting (Octet 18 - Bit 2)
Write Default Erroneous Data Reporting (Octet 18 - Bit 3)
......
< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
> HCI Event: Command Complete (0x0e) plen 4
Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1
Status: Unknown HCI Command (0x01)
< HCI Command: Read Local Supported Features (0x04|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Supported Features (0x04|0x0003) ncmd 1
Status: Success (0x00)
Features: 0xff 0xfe 0x0f 0xfe 0xd8 0x3f 0x5b 0x87
3 slot packets
......
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Zijun Hu [Wed, 13 Jul 2022 06:53:14 +0000 (14:53 +0800)]
Bluetooth: hci_sync: Correct hci_set_event_mask_page_2_sync() event mask
Event HCI_Truncated_Page_Complete should belong to central
and HCI_Peripheral_Page_Response_Timeout should belong to
peripheral, but hci_set_event_mask_page_2_sync() take these
two events for wrong roles, so correct it by this change.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
He Wang [Sat, 25 Jun 2022 09:03:57 +0000 (17:03 +0800)]
Bluetooth: btusb: Add a new VID/PID 0489/e0e2 for MT7922
Add VID/PID 0489:e0e2 for MediaTek MT7922 Bluetooth chip. Found and
tested with Asus UM5302TA.
From /sys/kernel/debug/usb/devices:
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e0e2 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=
000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: He Wang <xw897002528@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Yuri D'Elia [Wed, 13 Jul 2022 15:29:13 +0000 (17:29 +0200)]
Bluetooth: btusb: Set HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN for MTK
This sets HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN for MTK controllers
since SCO appear to not work when using HCI_OP_ENHANCED_SETUP_SYNC_CONN.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215576
Signed-off-by: Yuri D'Elia <wavexx@thregr.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hakan Jansson [Thu, 30 Jun 2022 12:53:45 +0000 (14:53 +0200)]
Bluetooth: hci_bcm: Increase host baudrate for CYW55572 in autobaud mode
Add device specific data for max baudrate in autobaud mode. This allows the
host to use a baudrate higher than "init speed" when loading FW in autobaud
mode.
The device specific max baudrate in autobaud mode for CYW55572 is set to
921600 bps. Devices without device specific max baudrate in autobaud mode
will use init speed as before. If no device specific init speed has been
specified, it will default to the bcm_proto default 115200 bps.
The increased baud rate improves FW load time. The exact load time will
depend on the specific system and FW being used. As a rough indication,
the FW load time dropped from ~9s @ 115.2kbps to ~1.7s @ 921.6kbps in one
test.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hakan Jansson [Thu, 30 Jun 2022 12:45:23 +0000 (14:45 +0200)]
Bluetooth: hci_bcm: Prevent early baudrate setting in autobaud mode
Always prevent trying to set device baudrate before calling setup() when
using autobaud mode.
This was previously happening for devices which had device specific data
with member no_early_set_baudrate set to 0.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hakan Jansson [Thu, 30 Jun 2022 12:45:22 +0000 (14:45 +0200)]
Bluetooth: hci_bcm: Add DT compatible for CYW55572
CYW55572 is a Wi-Fi + Bluetooth combo device from Infineon.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hakan Jansson [Thu, 30 Jun 2022 12:45:21 +0000 (14:45 +0200)]
dt-bindings: net: broadcom-bluetooth: Add conditional constraints
Add conditional constraint to make property "reset-gpios" available only
for compatible devices acually having the reset pin.
Make property "brcm,requires-autobaud-mode" depend on property
"shutdown-gpios" as the shutdown pin is required to enter autobaud mode.
I looked at all compatible devices and compiled the matrix below before
formulating the conditional constraint. This was a pure paper exercise and
no verification testing has been performed.
d
e
v h
i o
c s
s e t
h - -
u w w v
t r a a v d
d e k k b d
o s e e a i
w e u u t o
n t p p - -
- - - - s s
g g g g u u
p p p p t p p
i i i i x l p p
o o o o c p l l
s s s s o o y y
---------------------------------------
brcm,bcm20702a1 X X X X X X X X
brcm,bcm4329-bt X X X X X X X X
brcm,bcm4330-bt X X X X X X X X
brcm,bcm4334-bt X - X X X X X X
brcm,bcm43438-bt X - X X X X X X
brcm,bcm4345c5 X - X X X X X X
brcm,bcm43540-bt X - X X X X X X
brcm,bcm4335a0 X - X X X X X X
brcm,bcm4349-bt X - X X X X X X
infineon,cyw55572-bt X - X X X X X X
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hakan Jansson [Thu, 30 Jun 2022 12:45:20 +0000 (14:45 +0200)]
dt-bindings: net: broadcom-bluetooth: Add CYW55572 DT binding
CYW55572 is a Wi-Fi + Bluetooth combo device from Infineon.
Extend the binding with its DT compatible.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Dan Carpenter [Wed, 20 Jul 2022 11:23:49 +0000 (14:23 +0300)]
Bluetooth: clean up error pointer checking
The bt_skb_sendmsg() function can't return NULL so there is no need to
check for that. Several of these checks were removed previously but
this one was missed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hilda Wu [Thu, 14 Jul 2022 11:25:23 +0000 (19:25 +0800)]
Bluetooth: btusb: Add Realtek RTL8852C support ID 0x13D3:0x3586
Add the support ID(0x13D3, 0x3586) to usb_device_id table for
Realtek RTL8852C.
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3586 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=
00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hilda Wu [Thu, 14 Jul 2022 11:25:22 +0000 (19:25 +0800)]
Bluetooth: btusb: Add Realtek RTL8852C support ID 0x13D3:0x3587
Add the support ID(0x13D3, 0x3587) to usb_device_id table for
Realtek RTL8852C.
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3587 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=
00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hilda Wu [Thu, 14 Jul 2022 11:25:21 +0000 (19:25 +0800)]
Bluetooth: btusb: Add Realtek RTL8852C support ID 0x0CB8:0xC558
Add the support ID(0x0CB8, 0xC558) to usb_device_id table for
Realtek RTL8852C.
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cb8 ProdID=c558 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=
00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hilda Wu [Thu, 14 Jul 2022 11:25:20 +0000 (19:25 +0800)]
Bluetooth: btusb: Add Realtek RTL8852C support ID 0x04C5:0x1675
Add the support ID(0x04c5, 0x1675) to usb_device_id table for
Realtek RTL8852C.
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04c5 ProdID=1675 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=
00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hilda Wu [Thu, 14 Jul 2022 11:25:19 +0000 (19:25 +0800)]
Bluetooth: btusb: Add Realtek RTL8852C support ID 0x04CA:0x4007
Add the support ID(0x04CA, 0x4007) to usb_device_id table for
Realtek RTL8852C.
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04ca ProdID=4007 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=
00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Ying Hsu [Mon, 4 Jul 2022 10:33:24 +0000 (18:33 +0800)]
Bluetooth: Add default wakeup callback for HCI UART driver
Bluetooth HCI devices indicate if they are able to wakeup in the wakeup
callback since 'commit
4539ca67fe8e ("Bluetooth: Rename driver
.prevent_wake to .wakeup")'. This patch adds a default wakeup callback
for Bluetooth HCI UAR devices. It assumes Bluetooth HCI UART devices are
wakeable for backward compatibility. For those who need a customized
behavior, one can override it before calling hci_uart_register_device().
Fixes:
4539ca67fe8e ("Bluetooth: Rename driver .prevent_wake to .wakeup")
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Thu, 14 Jul 2022 00:17:55 +0000 (17:17 -0700)]
Bluetooth: hci_sync: Don't remove connected devices from accept list
These devices are likely going to be reprogrammed when disconnected so
this avoid a whole bunch of commands attempt to remove and the add back
to the list.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Zhengping Jiang <jiangzp@google.com>
Luiz Augusto von Dentz [Thu, 14 Jul 2022 00:12:14 +0000 (17:12 -0700)]
Bluetooth: hci_sync: Fix not updating privacy_mode
When programming a new entry into the resolving list it shall default
to network mode since the params may contain the mode programmed when
the device was last added to the resolving list.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209745
Fixes:
853b70b506a20 ("Bluetooth: hci_sync: Set Privacy Mode when updating the resolving list")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Zhengping Jiang <jiangzp@google.com>
Tamas Koczka [Thu, 14 Jul 2022 10:48:14 +0000 (10:48 +0000)]
Bluetooth: Collect kcov coverage from hci_rx_work
Annotate hci_rx_work() with kcov_remote_start() and kcov_remote_stop()
calls, so remote KCOV coverage is collected while processing the rx_q
queue which is the main incoming Bluetooth packet queue.
Coverage is associated with the thread which created the packet skb.
The collected extra coverage helps kernel fuzzing efforts in finding
vulnerabilities.
This change only has effect if the kernel is compiled with CONFIG_KCOV,
otherwise kcov_ functions don't do anything.
Signed-off-by: Tamas Koczka <poprdi@google.com>
Tested-by: Aleksandr Nogikh <nogikh@google.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Zhengping Jiang [Tue, 12 Jul 2022 00:05:30 +0000 (17:05 -0700)]
Bluetooth: hci_sync: Fix resuming scan after suspend resume
After resuming, remove setting scanning_paused to false, because it is
checked and set to false in hci_resume_scan_sync. Also move setting
the value to false before updating passive scan, because the value is
used when resuming passive scan.
Fixes:
3b42055388c30 (Bluetooth: hci_sync: Fix attempting to suspend with
unfiltered passive scan)
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Sean Wang [Sun, 26 Jun 2022 23:27:36 +0000 (07:27 +0800)]
Bluetooth: btmtksdio: Add in-band wakeup support
Commit
ce64b3e94919 ("Bluetooth: mt7921s: Support wake on bluetooth")
adds the wake on bluethooth via a dedicated GPIO.
Extend the wake-on-bluetooth to use the SDIO DAT1 pin (in-band wakeup),
when supported by the SDIO host driver.
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Zhengping Jiang [Mon, 13 Jun 2022 21:43:27 +0000 (14:43 -0700)]
Bluetooth: mgmt: Fix refresh cached connection info
Set the connection data before calling get_conn_info_sync, so it can be
verified the connection is still connected, before refreshing cached
values.
Fixes:
47db6b42991e6 ("Bluetooth: hci_sync: Convert MGMT_OP_GET_CONN_INFO")
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Wed, 8 Jun 2022 22:00:01 +0000 (15:00 -0700)]
Bluetooth: HCI: Fix not always setting Scan Response/Advertising Data
The scan response and advertising data needs to be tracked on a per
instance (adv_info) since when these instaces are removed so are their
data, to fix that new flags are introduced which is used to mark when
the data changes and then checked to confirm when the data needs to be
synced with the controller.
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Tue, 24 May 2022 20:02:45 +0000 (13:02 -0700)]
Bluetooth: eir: Fix using strlen with hdev->{dev_name,short_name}
Both dev_name and short_name are not guaranteed to be NULL terminated so
this instead use strnlen and then attempt to determine if the resulting
string needs to be truncated or not.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216018
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Xiaohui Zhang [Tue, 7 Jun 2022 15:30:20 +0000 (23:30 +0800)]
Bluetooth: use memset avoid memory leaks
Similar to the handling of l2cap_ecred_connect in commit
d3715b2333e9
("Bluetooth: use memset avoid memory leaks"), we thought a patch
might be needed here as well.
Use memset to initialize structs to prevent memory leaks
in l2cap_le_connect
Signed-off-by: Xiaohui Zhang <xiaohuizhang@ruc.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Dan Carpenter [Wed, 8 Jun 2022 13:46:13 +0000 (16:46 +0300)]
Bluetooth: fix an error code in hci_register_dev()
Preserve the error code from hci_register_suspend_notifier(). Don't
return success.
Fixes:
d6bb2a91f95b ("Bluetooth: Unregister suspend with userchannel")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Ahmad Fatoum [Tue, 24 May 2022 05:56:41 +0000 (07:56 +0200)]
Bluetooth: hci_bcm: Add BCM4349B1 variant
The BCM4349B1, aka CYW/BCM89359, is a WiFi+BT chip and its Bluetooth
portion can be controlled over serial.
Two subversions are added for the chip, because ROM firmware reports
002.002.013 (at least for the chips I have here), while depending on
patchram firmware revision, either 002.002.013 or 002.002.014 is
reported.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Ahmad Fatoum [Tue, 24 May 2022 05:56:40 +0000 (07:56 +0200)]
dt-bindings: bluetooth: broadcom: Add BCM4349B1 DT binding
The BCM4349B1, aka CYW/BCM89359, is a WiFi+BT chip and its Bluetooth
portion can be controlled over serial.
Extend the binding with its DT compatible.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Abhishek Pandit-Subedi [Thu, 2 Jun 2022 16:46:50 +0000 (09:46 -0700)]
Bluetooth: Unregister suspend with userchannel
When HCI_USERCHANNEL is used, unregister the suspend notifier when
binding and register when releasing. The userchannel socket should be
left alone after open is completed.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Abhishek Pandit-Subedi [Thu, 2 Jun 2022 16:46:49 +0000 (09:46 -0700)]
Bluetooth: Fix index added after unregister
When a userchannel socket is released, we should check whether the hdev
is already unregistered before sending out an IndexAdded.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Schspa Shi [Fri, 3 Jun 2022 08:19:14 +0000 (16:19 +0800)]
Bluetooth: When HCI work queue is drained, only queue chained work
The HCI command, event, and data packet processing workqueue is drained
to avoid deadlock in commit
76727c02c1e1 ("Bluetooth: Call drain_workqueue() before resetting state").
There is another delayed work, which will queue command to this drained
workqueue. Which results in the following error report:
Bluetooth: hci2: command 0x040f tx timeout
WARNING: CPU: 1 PID: 18374 at kernel/workqueue.c:1438 __queue_work+0xdad/0x1140
Workqueue: events hci_cmd_timeout
RIP: 0010:__queue_work+0xdad/0x1140
RSP: 0000:
ffffc90002cffc60 EFLAGS:
00010093
RAX:
0000000000000000 RBX:
ffff8880b9d3ec00 RCX:
0000000000000000
RDX:
ffff888024ba0000 RSI:
ffffffff814e048d RDI:
ffff8880b9d3ec08
RBP:
0000000000000008 R08:
0000000000000000 R09:
00000000b9d39700
R10:
ffffffff814f73c6 R11:
0000000000000000 R12:
ffff88807cce4c60
R13:
0000000000000000 R14:
ffff8880796d8800 R15:
ffff8880796d8800
FS:
0000000000000000(0000) GS:
ffff8880b9d00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
000000c0174b4000 CR3:
000000007cae9000 CR4:
00000000003506e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
<TASK>
? queue_work_on+0xcb/0x110
? lockdep_hardirqs_off+0x90/0xd0
queue_work_on+0xee/0x110
process_one_work+0x996/0x1610
? pwq_dec_nr_in_flight+0x2a0/0x2a0
? rwlock_bug.part.0+0x90/0x90
? _raw_spin_lock_irq+0x41/0x50
worker_thread+0x665/0x1080
? process_one_work+0x1610/0x1610
kthread+0x2e9/0x3a0
? kthread_complete_and_exit+0x40/0x40
ret_from_fork+0x1f/0x30
</TASK>
To fix this, we can add a new HCI_DRAIN_WQ flag, and don't queue the
timeout workqueue while command workqueue is draining.
Fixes:
76727c02c1e1 ("Bluetooth: Call drain_workqueue() before resetting state")
Reported-by: syzbot+63bed493aebbf6872647@syzkaller.appspotmail.com
Signed-off-by: Schspa Shi <schspa@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jiasheng Jiang [Fri, 3 Jun 2022 01:24:36 +0000 (09:24 +0800)]
Bluetooth: hci_intel: Add check for platform_driver_register
As platform_driver_register() could fail, it should be better
to deal with the return value in order to maintain the code
consisitency.
Fixes:
1ab1f239bf17 ("Bluetooth: hci_intel: Add support for platform driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alain Michaud [Thu, 2 Jun 2022 15:30:03 +0000 (15:30 +0000)]
Bluetooth: clear the temporary linkkey in hci_conn_cleanup
If a hardware error occurs and the connections are flushed without a
disconnection_complete event being signaled, the temporary linkkeys are
not flushed.
This change ensures that any outstanding flushable linkkeys are flushed
when the connection are flushed from the hash table.
Additionally, this also makes use of test_and_clear_bit to avoid
multiple attempts to delete the link key that's already been flushed.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Hakan Jansson [Mon, 30 May 2022 15:02:18 +0000 (17:02 +0200)]
Bluetooth: hci_bcm: Add support for FW loading in autobaud mode
Use the presence of a DT property, "brcm,requires-autobaud-mode", to enable
startup in autobaud mode. If the property is present, the device is started
in autobaud mode by asserting RTS (BT_UART_CTS_N) prior to powering on the
device.
Also prevent the use of unsupported commands for devices started in
autobaud mode. Only a limited subset of HCI commands are supported in
autobaud mode.
Some devices (e.g. CYW5557x) require autobaud mode to enable FW loading.
Autobaud mode can also be required on some boards where the controller
device is using a non-standard baud rate in normal mode when first powered
on.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Hakan Jansson [Mon, 30 May 2022 15:02:17 +0000 (17:02 +0200)]
dt-bindings: net: broadcom-bluetooth: Add property for autobaud mode
Add property, "brcm,requires-autobaud-mode", to enable autobaud mode
selection.
Some devices (e.g. CYW5557x) require autobaud mode to enable FW loading.
Autobaud mode can also be required on some boards where the controller
device is using a non-standard baud rate when first powered on.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sai Teja Aluvala [Fri, 27 May 2022 10:15:43 +0000 (15:45 +0530)]
Bluetooth: hci_qca: Return wakeup for qca_wakeup
This fixes the return value of qca_wakeup(), since
.wakeup work inversely with original .prevent_wake.
Fixes:
4539ca67fe8ed (Bluetooth: Rename driver .prevent_wake to .wakeup)
Signed-off-by: Sai Teja Aluvala <quic_saluvala@quicinc.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Aaron Ma [Thu, 2 Jun 2022 09:28:22 +0000 (17:28 +0800)]
Bluetooth: btusb: Add support of IMC Networks PID 0x3568
It is 13d3:3568 for MediaTek MT7922 USB Bluetooth chip.
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3568 Rev=01.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=...
C: #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jakub Kicinski [Thu, 21 Jul 2022 20:03:39 +0000 (13:03 -0700)]
Merge git://git./linux/kernel/git/netdev/net
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 21 Jul 2022 18:08:35 +0000 (11:08 -0700)]
Merge tag 'net-5.19-rc8' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from can.
Still no major regressions, most of the changes are still due to data
races fixes, plus the usual bunch of drivers fixes.
Previous releases - regressions:
- tcp/udp: make early_demux back namespacified.
- dsa: fix issues with vlan_filtering_is_global
Previous releases - always broken:
- ip: fix data-races around ipv4_net_table (round 2, 3 & 4)
- amt: fix validation and synchronization bugs
- can: fix detection of mcp251863
- eth: iavf: fix handling of dummy receive descriptors
- eth: lan966x: fix issues with MAC table
- eth: stmmac: dwmac-mediatek: fix clock issue
Misc:
- dsa: update documentation"
* tag 'net-5.19-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (107 commits)
mlxsw: spectrum_router: Fix IPv4 nexthop gateway indication
net/sched: cls_api: Fix flow action initialization
tcp: Fix data-races around sysctl_tcp_max_reordering.
tcp: Fix a data-race around sysctl_tcp_abort_on_overflow.
tcp: Fix a data-race around sysctl_tcp_rfc1337.
tcp: Fix a data-race around sysctl_tcp_stdurg.
tcp: Fix a data-race around sysctl_tcp_retrans_collapse.
tcp: Fix data-races around sysctl_tcp_slow_start_after_idle.
tcp: Fix a data-race around sysctl_tcp_thin_linear_timeouts.
tcp: Fix data-races around sysctl_tcp_recovery.
tcp: Fix a data-race around sysctl_tcp_early_retrans.
tcp: Fix data-races around sysctl knobs related to SYN option.
udp: Fix a data-race around sysctl_udp_l3mdev_accept.
ip: Fix data-races around sysctl_ip_prot_sock.
ipv4: Fix data-races around sysctl_fib_multipath_hash_fields.
ipv4: Fix data-races around sysctl_fib_multipath_hash_policy.
ipv4: Fix a data-race around sysctl_fib_multipath_use_neigh.
can: rcar_canfd: Add missing of_node_put() in rcar_canfd_probe()
can: mcp251xfd: fix detection of mcp251863
Documentation: fix udp_wmem_min in ip-sysctl.rst
...
Peter Zijlstra [Fri, 8 Jul 2022 07:18:06 +0000 (09:18 +0200)]
mmu_gather: Force tlb-flush VM_PFNMAP vmas
Jann reported a race between munmap() and unmap_mapping_range(), where
unmap_mapping_range() will no-op once unmap_vmas() has unlinked the
VMA; however munmap() will not yet have invalidated the TLBs.
Therefore unmap_mapping_range() will complete while there are still
(stale) TLB entries for the specified range.
Mitigate this by force flushing TLBs for VM_PFNMAP ranges.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Zijlstra [Fri, 8 Jul 2022 07:18:05 +0000 (09:18 +0200)]
mmu_gather: Let there be one tlb_{start,end}_vma() implementation
Now that architectures are no longer allowed to override
tlb_{start,end}_vma() re-arrange code so that there is only one
implementation for each of these functions.
This much simplifies trying to figure out what they actually do.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Zijlstra [Fri, 8 Jul 2022 07:18:04 +0000 (09:18 +0200)]
csky/tlb: Remove tlb_flush() define
The previous patch removed the tlb_flush_end() implementation which
used tlb_flush_range(). This means:
- csky did double invalidates, a range invalidate per vma and a full
invalidate at the end
- csky actually has range invalidates and as such the generic
tlb_flush implementation is more efficient for it.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will@kernel.org>
Tested-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Zijlstra [Fri, 8 Jul 2022 07:18:03 +0000 (09:18 +0200)]
mmu_gather: Remove per arch tlb_{start,end}_vma()
Scattered across the archs are 3 basic forms of tlb_{start,end}_vma().
Provide two new MMU_GATHER_knobs to enumerate them and remove the per
arch tlb_{start,end}_vma() implementations.
- MMU_GATHER_NO_FLUSH_CACHE indicates the arch has flush_cache_range()
but does *NOT* want to call it for each VMA.
- MMU_GATHER_MERGE_VMAS indicates the arch wants to merge the
invalidate across multiple VMAs if possible.
With these it is possible to capture the three forms:
1) empty stubs;
select MMU_GATHER_NO_FLUSH_CACHE and MMU_GATHER_MERGE_VMAS
2) start: flush_cache_range(), end: empty;
select MMU_GATHER_MERGE_VMAS
3) start: flush_cache_range(), end: flush_tlb_range();
default
Obviously, if the architecture does not have flush_cache_range() then
it also doesn't need to select MMU_GATHER_NO_FLUSH_CACHE.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will@kernel.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Khalid Masum [Thu, 21 Jul 2022 09:30:42 +0000 (15:30 +0600)]
scripts/gdb: Fix gdb 'lx-symbols' command
Currently the command 'lx-symbols' in gdb exits with the error`Function
"do_init_module" not defined in "kernel/module.c"`. This occurs because
the file kernel/module.c was moved to kernel/module/main.c.
Fix this breakage by changing the path to "kernel/module/main.c" in
LoadModuleBreakpoint.
Signed-off-by: Khalid Masum <khalid.masum.92@gmail.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Fixes:
cfc1d277891e ("module: Move all into module/")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 21 Jul 2022 17:30:14 +0000 (10:30 -0700)]
watch-queue: remove spurious double semicolon
Sedat Dilek noticed that I had an extraneous semicolon at the end of a
line in the previous patch.
It's harmless, but unintentional, and while compilers just treat it as
an extra empty statement, for all I know some other tooling might warn
about it. So clean it up before other people notice too ;)
Fixes:
353f7988dd84 ("watchqueue: make sure to serialize 'wqueue->defunct' properly")
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Łukasz Spintzyk [Wed, 20 Jul 2022 06:05:18 +0000 (08:05 +0200)]
net/cdc_ncm: Increase NTB max RX/TX values to 64kb
DisplayLink ethernet devices require NTB buffers larger then 32kb
in order to run with highest performance.
This patch is changing upper limit of the rx and tx buffers.
Those buffers are initialized with CDC_NCM_NTB_DEF_SIZE_RX and
CDC_NCM_NTB_DEF_SIZE_TX which is 16kb so by default no device is
affected by increased limit.
Rx and tx buffer is increased under two conditions:
- Device need to advertise that it supports higher buffer size in
dwNtbMaxInMaxSize and dwNtbMaxOutMaxSize.
- cdc_ncm/rx_max and cdc_ncm/tx_max driver parameters must be adjusted
with udev rule or ethtool.
Summary of testing and performance results:
Tests were performed on following devices:
- DisplayLink DL-3xxx family device
- DisplayLink DL-6xxx family device
- ASUS USB-C2500 2.5G USB3 ethernet adapter
- Plugable USB3 1G USB3 ethernet adapter
- EDIMAX EU-4307 USB-C ethernet adapter
- Dell DBQBCBC064 USB-C ethernet adapter
Performance measurements were done with:
- iperf3 between two linux boxes
- http://openspeedtest.com/ instance running on local test machine
Insights from tests results:
- All except one from third party usb adapters were not affected by
increased buffer size to their advertised dwNtbOutMaxSize and
dwNtbInMaxSize.
Devices were generally reaching 912-940Mbps both download and upload.
Only EDIMAX adapter experienced decreased download size from
929Mbps to 827Mbps with iper3, with openspeedtest decrease was from
968Mbps to 886Mbps.
- DisplayLink DL-3xxx family devices experienced performance increase
with iperf3 download from 300Mbps to 870Mbps and
upload from 782Mbps to 844Mbps.
With openspeedtest download increased from 556Mbps to 873Mbps
and upload from 727Mbps to 973Mbps
- DiplayLink DL-6xxx family devices are not affected by
increased buffer size.
Signed-off-by: Łukasz Spintzyk <lukasz.spintzyk@synaptics.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220720060518.541-2-lukasz.spintzyk@synaptics.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Dominik Czerwik [Wed, 20 Jul 2022 06:05:17 +0000 (08:05 +0200)]
net/cdc_ncm: Enable ZLP for DisplayLink ethernet devices
This improves performance and stability of
DL-3xxx/DL-5xxx/DL-6xxx device series.
Specifically prevents device from temporary network dropouts when
playing video from the web and network traffic going through is high.
Signed-off-by: Dominik Czerwik <dominik.czerwik@synaptics.com>
Signed-off-by: Łukasz Spintzyk <lukasz.spintzyk@synaptics.com>
Link: https://lore.kernel.org/r/20220720060518.541-1-lukasz.spintzyk@synaptics.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Thu, 21 Jul 2022 04:05:44 +0000 (21:05 -0700)]
Merge branch 'net-ipa-move-configuration-data-files'
Alex Elder says:
====================
net: ipa: move configuration data files
This series moves the "ipa_data-vX.Y.c" files into a subdirectory.
The first patch adds a Makefile variable containing the list of
supported IPA versions, and uses it to simplify the way these files
are specified.
====================
Link: https://lore.kernel.org/r/20220719150827.295248-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Tue, 19 Jul 2022 15:08:27 +0000 (10:08 -0500)]
net: ipa: move configuration data files into a subdirectory
Reduce the clutter in the main IPA source directory by creating a
new "data" subdirectory, and locating all of the configuration data
files in there.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Tue, 19 Jul 2022 15:08:26 +0000 (10:08 -0500)]
net: ipa: list supported IPA versions in the Makefile
Create a variable in the Makefile listing the IPA versions supported
by the driver. Use that to create the list of configuration data
object files used (rather than listing them all individually).
Add a SPDX license comment.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 21 Jul 2022 04:05:07 +0000 (21:05 -0700)]
Merge branch 'net-ipa-small-transaction-updates'
Alex Elder says:
====================
net: ipa: small transaction updates
Version 2 of this series corrects a misspelling of "outstanding"
pointed out by the netdev test bots. (For some reason I don't see
that when I run "checkpatch".) I found and fixed a second instance
of that word being misspelled as well.
This series includes three changes to the transaction code. The
first adds a new transaction list that represents a distinct state
that has not been maintained. The second moves a field in the
transaction information structure, and reorders its initialization
a bit. The third skips a function call when it is known not to be
necessary.
The last two are very small "leftover" patches.
====================
Link: https://lore.kernel.org/r/20220719181020.372697-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Tue, 19 Jul 2022 18:10:20 +0000 (13:10 -0500)]
net: ipa: fix an outdated comment
Since commit
8797972afff3d ("net: ipa: remove command info pool"),
we don't allocate "command info" entries for command channel
transactions. Fix a comment that seems to suggest we still do.
(Even before that commit, the comment was out of place.)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Tue, 19 Jul 2022 18:10:19 +0000 (13:10 -0500)]
net: ipa: report when the driver has been removed
When the IPA driver has completed its initialization and setup
stages, it emits a brief message to the log. Add a small message
that reports when it has been removed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Tue, 19 Jul 2022 18:10:18 +0000 (13:10 -0500)]
net: ipa: skip some cleanup for unused transactions
In gsi_trans_free(), there's no point in ipa_gsi_trans_release() if
a transaction is unused. No used TREs means no IPA layer resources
to clean up. So only call ipa_gsi_trans_release() if at least one
TRE was used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Tue, 19 Jul 2022 18:10:17 +0000 (13:10 -0500)]
net: ipa: rearrange transaction initialization
The transaction map is really associated with the transaction pool;
move its definition earlier in the gsi_trans_info structure.
Rearrange initialization in gsi_channel_trans_init() so it
sets the tre_avail value first, then initializes the transaction
pool, and finally allocating the transaction map.
Update comments.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Tue, 19 Jul 2022 18:10:16 +0000 (13:10 -0500)]
net: ipa: add a transaction committed list
We currently put a transaction on the pending list when it has
been committed. But until the channel's doorbell rings, these
transactions aren't actually "owned" by the hardware yet.
Add a new "committed" state (and list), to represent transactions
that have been committed but not yet sent to hardware. Define
"pending" to mean committed transactions that have been sent
to hardware but have not yet completed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Tue, 19 Jul 2022 19:16:39 +0000 (14:16 -0500)]
net: ipa: add an endpoint device attribute group
Create a new attribute group meant to provide a single place that
defines endpoint IDs that might be needed by user space. Not all
defined endpoints are presented, and only those that are defined
will be made visible.
The new attributes use "extended" device attributes to hold endpoint
IDs, which is a little more compact and efficient. Reimplement the
existing modem endpoint ID attribute files using common code.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20220719191639.373249-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kuniyuki Iwashima [Wed, 20 Jul 2022 00:57:50 +0000 (17:57 -0700)]
selftests: net: af_unix: Fix a build error of unix_connect.c.
This patch fixes a build error reported in the link. [0]
unix_connect.c: In function ‘unix_connect_test’:
unix_connect.c:115:55: error: expected identifier before ‘(’ token
#define offsetof(type, member) ((size_t)&((type *)0)->(member))
^
unix_connect.c:128:12: note: in expansion of macro ‘offsetof’
addrlen = offsetof(struct sockaddr_un, sun_path) + variant->len;
^~~~~~~~
We can fix this by removing () around member, but checkpatch will complain
about it, and the root cause of the build failure is that I followed the
warning and fixed this in the v2 -> v3 change of the blamed commit. [1]
CHECK: Macro argument 'member' may be better as '(member)' to avoid precedence issues
#33: FILE: tools/testing/selftests/net/af_unix/unix_connect.c:115:
+#define offsetof(type, member) ((size_t)&((type *)0)->member)
To avoid this warning, let's use offsetof() defined in stddef.h instead.
[0]: https://lore.kernel.org/linux-mm/
202207182205.FrkMeDZT-lkp@intel.com/
[1]: https://lore.kernel.org/netdev/
20220702154818.66761-1-kuniyu@amazon.com/
Fixes:
e95ab1d85289 ("selftests: net: af_unix: Test connect() with different netns.")
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20220720005750.16600-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jian Shen [Tue, 19 Jul 2022 14:24:24 +0000 (22:24 +0800)]
net: amd8111e: remove repeated dev->features assignement
It's repeated with line 1793-1795, and there isn't any other
handling for it. So remove it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Link: https://lore.kernel.org/r/20220719142424.4528-1-shenjian15@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 21 Jul 2022 01:05:51 +0000 (18:05 -0700)]
Merge git://git./linux/kernel/git/netfilter/nf-next
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Simplify nf_ct_get_tuple(), from Jackie Liu.
2) Add format to request_module() call, from Bill Wendling.
3) Add /proc/net/stats/nf_flowtable to monitor in-flight pending
hardware offload objects to be processed, from Vlad Buslov.
4) Missing rcu annotation and accessors in the netfilter tree,
from Florian Westphal.
5) Merge h323 conntrack helper nat hooks into single object,
also from Florian.
6) A batch of update to fix sparse warnings treewide,
from Florian Westphal.
7) Move nft_cmp_fast_mask() where it used, from Florian.
8) Missing const in nf_nat_initialized(), from James Yonan.
9) Use bitmap API for Maglev IPVS scheduler, from Christophe Jaillet.
10) Use refcount_inc instead of _inc_not_zero in flowtable,
from Florian Westphal.
11) Remove pr_debug in xt_TPROXY, from Nathan Cancellor.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: xt_TPROXY: remove pr_debug invocations
netfilter: flowtable: prefer refcount_inc
netfilter: ipvs: Use the bitmap API to allocate bitmaps
netfilter: nf_nat: in nf_nat_initialized(), use const struct nf_conn *
netfilter: nf_tables: move nft_cmp_fast_mask to where its used
netfilter: nf_tables: use correct integer types
netfilter: nf_tables: add and use BE register load-store helpers
netfilter: nf_tables: use the correct get/put helpers
netfilter: x_tables: use correct integer types
netfilter: nfnetlink: add missing __be16 cast
netfilter: nft_set_bitmap: Fix spelling mistake
netfilter: h323: merge nat hook pointers into one
netfilter: nf_conntrack: use rcu accessors where needed
netfilter: nf_conntrack: add missing __rcu annotations
netfilter: nf_flow_table: count pending offload workqueue tasks
net/sched: act_ct: set 'net' pointer when creating new nf_flow_table
netfilter: conntrack: use correct format characters
netfilter: conntrack: use fallthrough to cleanup
====================
Link: https://lore.kernel.org/r/20220720230754.209053-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 21 Jul 2022 00:54:46 +0000 (17:54 -0700)]
Merge tag 'mlx5-updates-2022-07-17' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2022-07-17
1) Add resiliency for lost completions for PTP TX port timestamp
2) Report Header-data split state via ethtool
3) Decouple HTB code from main regular TX code
* tag 'mlx5-updates-2022-07-17' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: CT: Remove warning of ignore_flow_level support for non PF
net/mlx5e: Add resiliency for PTP TX port timestamp
net/mlx5: Expose ts_cqe_metadata_size2wqe_counter
net/mlx5e: HTB, move htb functions to a new file
net/mlx5e: HTB, change functions name to follow convention
net/mlx5e: HTB, remove priv from htb function calls
net/mlx5e: HTB, hide and dynamically allocate mlx5e_htb structure
net/mlx5e: HTB, move stats and max_sqs to priv
net/mlx5e: HTB, move section comment to the right place
net/mlx5e: HTB, move ids to selq_params struct
net/mlx5e: HTB, reduce visibility of htb functions
net/mlx5e: Fix mqprio_rl handling on devlink reload
net/mlx5e: Report header-data split state through ethtool
====================
Link: https://lore.kernel.org/r/20220719203529.51151-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Justin Stitt [Tue, 12 Jul 2022 20:49:00 +0000 (13:49 -0700)]
netfilter: xt_TPROXY: remove pr_debug invocations
pr_debug calls are no longer needed in this file.
Pablo suggested "a patch to remove these pr_debug calls". This patch has
some other beneficial collateral as it also silences multiple Clang
-Wformat warnings that were present in the pr_debug calls.
diff from v1 -> v2:
* converted if statement one-liner style
* x == NULL is now !x
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Justin Stitt <justinstitt@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Thu, 7 Jul 2022 19:30:56 +0000 (21:30 +0200)]
netfilter: flowtable: prefer refcount_inc
With refcount_inc_not_zero, we'd also need a smp_rmb or similar,
followed by a test of the CONFIRMED bit.
However, the ct pointer is taken from skb->_nfct, its refcount must
not be 0 (else, we'd already have a use-after-free bug).
Use refcount_inc() instead to clarify the ct refcount is expected to
be at least 1.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Christophe JAILLET [Mon, 4 Jul 2022 19:24:46 +0000 (21:24 +0200)]
netfilter: ipvs: Use the bitmap API to allocate bitmaps
Use bitmap_zalloc()/bitmap_free() instead of hand-writing them.
It is less verbose and it improves the semantic.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Linus Torvalds [Tue, 19 Jul 2022 18:09:01 +0000 (11:09 -0700)]
watchqueue: make sure to serialize 'wqueue->defunct' properly
When the pipe is closed, we mark the associated watchqueue defunct by
calling watch_queue_clear(). However, while that is protected by the
watchqueue lock, new watchqueue entries aren't actually added under that
lock at all: they use the pipe->rd_wait.lock instead, and looking up
that pipe happens without any locking.
The watchqueue code uses the RCU read-side section to make sure that the
wqueue entry itself hasn't disappeared, but that does not protect the
pipe_info in any way.
So make sure to actually hold the wqueue lock when posting watch events,
properly serializing against the pipe being torn down.
Reported-by: Noam Rathaus <noamr@ssd-disclosure.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Snowberg [Wed, 20 Jul 2022 16:40:27 +0000 (12:40 -0400)]
lockdown: Fix kexec lockdown bypass with ima policy
The lockdown LSM is primarily used in conjunction with UEFI Secure Boot.
This LSM may also be used on machines without UEFI. It can also be
enabled when UEFI Secure Boot is disabled. One of lockdown's features
is to prevent kexec from loading untrusted kernels. Lockdown can be
enabled through a bootparam or after the kernel has booted through
securityfs.
If IMA appraisal is used with the "ima_appraise=log" boot param,
lockdown can be defeated with kexec on any machine when Secure Boot is
disabled or unavailable. IMA prevents setting "ima_appraise=log" from
the boot param when Secure Boot is enabled, but this does not cover
cases where lockdown is used without Secure Boot.
To defeat lockdown, boot without Secure Boot and add ima_appraise=log to
the kernel command line; then:
$ echo "integrity" > /sys/kernel/security/lockdown
$ echo "appraise func=KEXEC_KERNEL_CHECK appraise_type=imasig" > \
/sys/kernel/security/ima/policy
$ kexec -ls unsigned-kernel
Add a call to verify ima appraisal is set to "enforce" whenever lockdown
is enabled. This fixes CVE-2022-21505.
Cc: stable@vger.kernel.org
Fixes:
29d3c1c8dfe7 ("kexec: Allow kexec_file() with appropriate IMA policy when locked down")
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Acked-by: Mimi Zohar <zohar@linux.ibm.com>
Reviewed-by: John Haxby <john.haxby@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Wed, 20 Jul 2022 10:13:54 +0000 (11:13 +0100)]
Merge tag 'linux-can-fixes-for-5.19-
20220720' of git://git./linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
this is a pull request of 2 patches for net/master.
The first patch is by me and fixes the detection of the mcp251863 in
the mcp251xfd driver.
The last patch is by Liang He and adds a missing of_node_put() in the
rcar_canfd driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Tue, 19 Jul 2022 14:18:55 +0000 (09:18 -0500)]
net: ipa: initialize ring indexes to 0
When a GSI channel is initially allocated, and after it has been
reset, the hardware assumes its ring index is 0. And although we
do initialize channels this way, the comments in the IPA code don't
really explain this. For event rings, it doesn't matter what value
we use initially, so using 0 is just fine.
Add some information about the assumptions made by hardware above
the definition of the gsi_ring structure in "gsi.h".
Zero the index field for all rings (channel and event) when the ring
is allocated. As a result, that function initializes all fields in
the structure.
Stop zeroing the index the top of gsi_channel_program(). Initially
we'll use the index value set when the channel ring was allocated.
And we'll explicitly zero the index value in gsi_channel_reset()
before programming the hardware, adding a comment explaining why
it's required.
For event rings, use the index initialized by gsi_ring_alloc()
rather than 0 when ringing the doorbell in gsi_evt_ring_program().
(It'll still be zero, but we won't assume that to be the case.)
Use a local variable in gsi_evt_ring_program() that represents the
address of the event ring's ring structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 19 Jul 2022 12:26:26 +0000 (15:26 +0300)]
mlxsw: spectrum_router: Fix IPv4 nexthop gateway indication
mlxsw needs to distinguish nexthops with a gateway from connected
nexthops in order to write the former to the adjacency table of the
device. The check used to rely on the fact that nexthops with a gateway
have a 'link' scope whereas connected nexthops have a 'host' scope. This
is no longer correct after commit
747c14307214 ("ip: fix dflt addr
selection for connected nexthop").
Fix that by instead checking the address family of the gateway IP. This
is a more direct way and also consistent with the IPv6 counterpart in
mlxsw_sp_rt6_is_gateway().
Cc: stable@vger.kernel.org
Fixes:
747c14307214 ("ip: fix dflt addr selection for connected nexthop")
Fixes:
597cfe4fc339 ("nexthop: Add support for IPv4 nexthops")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oz Shlomo [Tue, 19 Jul 2022 12:24:09 +0000 (15:24 +0300)]
net/sched: cls_api: Fix flow action initialization
The cited commit refactored the flow action initialization sequence to
use an interface method when translating tc action instances to flow
offload objects. The refactored version skips the initialization of the
generic flow action attributes for tc actions, such as pedit, that allocate
more than one offload entry. This can cause potential issues for drivers
mapping flow action ids.
Populate the generic flow action fields for all the flow action entries.
Fixes:
c54e1d920f04 ("flow_offload: add ops to tc_action_ops for flow action setup")
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
----
v1 -> v2:
- coalese the generic flow action fields initialization to a single loop
Reviewed-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksandr Mazur [Tue, 19 Jul 2022 10:57:16 +0000 (13:57 +0300)]
net: marvell: prestera: add phylink support
For SFP port prestera driver will use kernel
phylink infrastucture to configure port mode based on
the module that has beed inserted
Co-developed-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Co-developed-by: Taras Chornyi <taras.chornyi@plvision.eu>
Signed-off-by: Taras Chornyi <taras.chornyi@plvision.eu>
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Turkin [Tue, 19 Jul 2022 04:29:55 +0000 (04:29 +0000)]
vmxnet3: Implement ethtool's get_channels command
Some tools (e.g. libxdp) use that information.
Signed-off-by: Andrey Turkin <andrey.turkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 20 Jul 2022 09:17:05 +0000 (10:17 +0100)]
Merge tag 'linux-can-next-for-5.20-
20220720' of git://git./linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
this is a pull request of 29 patches for net-next/master.
The first 6 patches target the slcan driver. Dan Carpenter contributes
a hardening patch, followed by 5 cleanup patches.
Biju Das contributes 5 patches to prepare the sja1000 driver to
support the Renesas RZ/N1 SJA1000 CAN controller.
Dario Binacchi's patch for the slcan driver fixes a sleep with held
spin lock.
Another patch by Dario Binacchi fixes a wrong comment in the c_can
driver.
Pavel Pisa updates the CTU CAN FD IP core registers.
Stephane Grosjean contributes 3 patches to the peak_usb driver for
cleanups and support of a new MCU.
The last 12 patches are by Vincent Mailhol, they fix and improve the
txerr and rxerr reporting in all CAN drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 20 Jul 2022 09:14:50 +0000 (10:14 +0100)]
Merge branch 'net-sysctl-races-round-4'
Kuniyuki Iwashima says:
====================
sysctl: Fix data-races around ipv4_net_table (Round 4).
This series fixes data-races around 17 knobs after fib_multipath_use_neigh
in ipv4_net_table.
tcp_fack was skipped because it's obsolete and there's no readers.
So, round 5 will start with tcp_dsack, 2 rounds left for 27 knobs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kuniyuki Iwashima [Mon, 18 Jul 2022 17:26:53 +0000 (10:26 -0700)]
tcp: Fix data-races around sysctl_tcp_max_reordering.
While reading sysctl_tcp_max_reordering, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes:
dca145ffaa8d ("tcp: allow for bigger reordering level")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kuniyuki Iwashima [Mon, 18 Jul 2022 17:26:52 +0000 (10:26 -0700)]
tcp: Fix a data-race around sysctl_tcp_abort_on_overflow.
While reading sysctl_tcp_abort_on_overflow, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kuniyuki Iwashima [Mon, 18 Jul 2022 17:26:51 +0000 (10:26 -0700)]
tcp: Fix a data-race around sysctl_tcp_rfc1337.
While reading sysctl_tcp_rfc1337, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kuniyuki Iwashima [Mon, 18 Jul 2022 17:26:50 +0000 (10:26 -0700)]
tcp: Fix a data-race around sysctl_tcp_stdurg.
While reading sysctl_tcp_stdurg, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kuniyuki Iwashima [Mon, 18 Jul 2022 17:26:49 +0000 (10:26 -0700)]
tcp: Fix a data-race around sysctl_tcp_retrans_collapse.
While reading sysctl_tcp_retrans_collapse, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kuniyuki Iwashima [Mon, 18 Jul 2022 17:26:48 +0000 (10:26 -0700)]
tcp: Fix data-races around sysctl_tcp_slow_start_after_idle.
While reading sysctl_tcp_slow_start_after_idle, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes:
35089bb203f4 ("[TCP]: Add tcp_slow_start_after_idle sysctl.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kuniyuki Iwashima [Mon, 18 Jul 2022 17:26:47 +0000 (10:26 -0700)]
tcp: Fix a data-race around sysctl_tcp_thin_linear_timeouts.
While reading sysctl_tcp_thin_linear_timeouts, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes:
36e31b0af587 ("net: TCP thin linear timeouts")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kuniyuki Iwashima [Mon, 18 Jul 2022 17:26:46 +0000 (10:26 -0700)]
tcp: Fix data-races around sysctl_tcp_recovery.
While reading sysctl_tcp_recovery, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes:
4f41b1c58a32 ("tcp: use RACK to detect losses")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kuniyuki Iwashima [Mon, 18 Jul 2022 17:26:45 +0000 (10:26 -0700)]
tcp: Fix a data-race around sysctl_tcp_early_retrans.
While reading sysctl_tcp_early_retrans, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes:
eed530b6c676 ("tcp: early retransmit")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kuniyuki Iwashima [Mon, 18 Jul 2022 17:26:44 +0000 (10:26 -0700)]
tcp: Fix data-races around sysctl knobs related to SYN option.
While reading these knobs, they can be changed concurrently.
Thus, we need to add READ_ONCE() to their readers.
- tcp_sack
- tcp_window_scaling
- tcp_timestamps
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>