drm/i915: Fix TGL+ plane SAGV watermark programming

When we switch between SAGV on vs. off we need to reprogram all
plane wateramrks accordingly. Currently skl_wm_add_affected_planes()
totally ignores the SAGV watermark and just assumes we will use
the normal WM0.

Fix this by utilizing skl_plane_wm_level() which picks the
correct watermark based on use_sagv_wm. Thus we will force
an update on all the planes whose watermark registers need
to be reprogrammed.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210226153204.1270-2-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>

drm/i915: Readout conn_state->max_bpc

Populate conn_state->max_bpc with something sensible from the start.
Otherwise it's possible that we get to compute_sink_pipe_bpp() with
max_bpc==0.

The specific scenario goes as follows:
1. Initial connector state allocated with max_bpc==0
2. Trigger a modeset on the crtc feeding the connector, without
   actually adding the connector to the commit
3. drm_atomic_connector_check() is skipped because the
   connector has not yet been added, hence conn_state->max_bpc
   retains its current value
4. drm_atomic_helper_check_modeset() ->
   drm_atomic_add_affected_connectors() -> the connector
   is now part of the commit
5. compute_baseline_pipe_bpp() -> MISSING_CASE(max_bpc==0)

Note that pipe_bpp itself may not be populated on pre-g4x machines,
in which case we just fall back to max_bpc==8 and let .compute_config()
limit the resulting pipe_bpp further if necessary.

Cc: Daniel Vetter <daniel@ffwll.ch>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210216160035.4780-1-ville.syrjala@linux.intel.com
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915/icp+: Use icp_hpd_irq_setup() instead of spt_hpd_irq_setup()

While reviewing patches for handling workarounds related to gen9 bc, Imre
from Intel discovered that we're using spt_hpd_irq_setup() on ICP+ PCHs
despite it being almost the same as icp_hpd_irq_setup(). Since we need to
be calling icp_hpd_irq_setup() to ensure that CML-S/TGP platforms function
correctly anyway, let's move platforms using PCH_ICP which aren't handled
by gen11_hpd_irq_setup() over to icp_hpd_irq_setup().

Cc: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210217025337.1929015-2-lyude@redhat.com

drm/i915/gen9bc: Handle TGP PCH during suspend/resume

For Legacy S3 suspend/resume GEN9 BC needs to enable and
setup TGP PCH.

v2:
* Move Wa_14010685332 into it's own function - vsyrjala
* Add TODO comment about figuring out if we can move this workaround - imre
v3:
* Rename cnp_irq_post_reset() to cnp_display_clock_wa()
* Add TODO item mentioning we need to clarify which platforms this
  workaround applies to
* Just use ibx_irq_reset() in gen8_irq_reset(). This code should be
  functionally equivalent on gen9 bc to the code v2 added
* Drop icp_hpd_irq_setup() call in spt_hpd_irq_setup(), this looks to be
  more or less identical to spt_hpd_irq_setup() minus additionally enabling
  one port. Will update i915 to use icp_hpd_irq_setup() for ICP in a
  separate patch.
v4:
* Revert Wa_14010685332 system list in comments to how it was before
* Add back HAS_PCH_SPLIT() check before calling ibx_irq_reset()

Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210217180016.1937401-1-lyude@redhat.com

drm/i915/tgl+: Sanitize the DDI LANES/IO and AUX power domain names

In Bspec the TGL TypeC ports are TC1-6, the AUX power well request flags
are USBC1-6/TBT1-6, so for clarity use these names in the port power
domain names instead of the D-I terminology (which Bspec uses only for
the ICL TypeC ports).

A domain name should follow the <domain>_<pipe/transcoder/port/aux_ch>
format. Add the new aliases based on this, leaving a change to rename
all the rest accordingly for a follow-up.

No functional change.

v2: Add comment to commit log about unifying domain names. (Jose)

Cc: Souza Jose <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210222210400.940158-1-imre.deak@intel.com

drm/i915/display: Do not allow DC3CO if PSR SF is enabled

Even though GEN12+ HW supports PSR + DC3CO, DMC's HW DC3CO exit mechanism
has an issue with using of Selective Fecth and PSR2 manual tracking.
And as some GEN12+ platforms (RKL, ADL-S) don't support PSR2 HW tracking,
Selective Fetch will be enabled by default on that platforms.
Therefore if the system enables PSR Selective Fetch / PSR manual tracking,
it does not allow DC3CO dc state, in that case.

When this DC3CO exit issue is addressed while PSR Selective Fetch is
enabled, this restriction should be removed.

v2: Address Jose's review comment.
  - Fix typo
  - Move check routine of DC3CO ability to
    tgl_dc3co_exitline_compute_config()
v3: Change the check routine of enablement of psr2 sel fetch. (Jose)

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210222213006.1609085-1-gwan-gyeong.mun@intel.com

drm/i915/reg: add stream splitter configuration definitions

The splitter configuration is required for eDP MSO.

Bspec: 50174
Cc: Nischal Varide <nischal.varide@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/443ad1fbf908800ee4e09315cb6a7ba26c64d136.1613054234.git.jani.nikula@intel.com

drm/i915/edp: read sink MSO configuration for eDP 1.4+

Read and debug log the eDP sink MSO configuration. Do not actually do
anything with the information yet besides logging.

FIXME: The pixel overlap is present in DisplayID 2.0, but we don't have
parsing for that. Assume zero for now. We could also add quirks for
non-zero pixel overlap before DisplayID 2.0 parsing.

v3: Add placeholder for pixel overlap.

v2: Rename intel_dp_mso_init -> intel_edp_mso_init

Cc: Nischal Varide <nischal.varide@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/24ef61574e5af12cd86d5b85afbfbd4ac2f9de25.1613054234.git.jani.nikula@intel.com

drm/i915/edp: always add fixed mode to probed modes in ->get_modes()

Unconditionally add fixed mode to probed modes even if EDID is present
and has modes. Prepare for cases where the fixed mode is not present in
EDID (such as eDP MSO).

Cc: Nischal Varide <nischal.varide@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6979f123f3e4ed948333f1b181202bbced3c3e85.1613054234.git.jani.nikula@intel.com

drm/i915/edp: reject modes with dimensions other than fixed mode

Be more strict about filtering modes for eDP.

Cc: Nischal Varide <nischal.varide@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/feb4c3b2b9c4da56a840bdb3c0e7fd0e58ee50de.1613054234.git.jani.nikula@intel.com

drm/dp: add MSO related DPCD registers

Add DPCD register definitions for eDP 1.4 Multi-SST Operation.

Cc: Nischal Varide <nischal.varide@intel.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ab57627f373ec4a80494bb51ea51080810d9bfb0.1613054234.git.jani.nikula@intel.com

drm/i915/display: Set source_support even if panel do not support PSR

This will set the right value of source_support when the port
encoder/port supports PSR but sink don't.

This change will also be needed in future for panel replay as psr
struct needs to be initialized even if disconnected or current sink
don't support PSR.

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209181439.215104-4-jose.souza@intel.com

drm/i915/display: Remove some redundancy around CAN_PSR()

If source_support is set the platform supports PSR so no need to check
it again at every CAN_PSR().

Also removing the intel_dp_is_edp() calls, if sink_support is set
the sink connected is for sure a eDP panel.

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209181439.215104-3-jose.souza@intel.com

drm/i915/display: Only write to register in intel_psr2_program_trans_man_trk_ctl()

There is no support for two pipes one transcoder for PSR and if we had
that the current code should not use cpu_transcoder.
Also I can't see a scenario where crtc_state->enable_psr2_sel_fetch is
set and PSR is not enabled and if by a bug it happens PSR HW will just
ignore any value in set in PSR2_MAN_TRK_CTL.

So dropping all the rest and keeping the same behavior that we have
with intel_psr2_program_plane_sel_fetch().

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209181439.215104-2-jose.souza@intel.com

drm/i915/display: Rename for_each_intel_encoder.*_can_psr to for_each_intel_encoder.*_with_psr

for_each_intel_encoder.*_"can_psr" sounds strange, in my opinion
"with_psr" is better.

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209181439.215104-1-jose.souza@intel.com

drm/i915/display: Allow PSR2 selective fetch to be enabled at run-time

Right now CI is blacklisting module reload, so we need to be able to
enable PSR2 selective fetch in run time to test this feature before
enable it by default.
Changes in IGT will also be needed.

v2:
- Fixed handling of I915_PSR_DEBUG_ENABLE_SEL_FETCH in
intel_psr_debug_set()

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209205036.351076-1-jose.souza@intel.com

drm/i915/vbt: update DP max link rate table

According to Bspec #20124, max link rate table for DP was updated
at BDB version 230. Max link rate can support upto UHBR.

After migrate to BDB v230, the definition for LBR, HBR2 and HBR3
were changed. For backward compatibility. If BDB version was
from 216 to 229. Driver have to follow original rule to configure
DP max link rate value from VBT.

v2: split the mapping table to two for old and new BDB definition.
v3: return link rate instead of assigning it.
v4: remove the useless variable.

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
[vsyrjala: Try to retain the comment that VBT version 216 added some of this]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210218052333.16109-1-shawn.c.lee@intel.com

drm/i915: Wait for scanout to stop when sanitizing planes

When we sanitize planes let's wait for the scanout to stop
before we let the subsequent code tear down the ggtt mappings
and whatnot. Cures an underrun on my ivb when I boot with
VT-d enabled and the BIOS fb gets thrown out due to stolen
being considered unusable with VT-d active.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210217162050.13803-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Nuke INTEL_OUTPUT_FORMAT_INVALID

We tend to use output_format!=RGB as a shorthand for YCbCr, but
this fails if we have a disabled crtc where output_format==INVALID.
We're now getting some fail from intel_color_check() when we have:
 hw.enable==false
 hw.ctm!=NULL
 output_format==INVALID

Let's avoid that by throwing INTEL_OUTPUT_FORMAT_INVALID to the
dumpster, and thus everything defaults to RGB when the crtc
is disabled.

This does beg the deeper question of how much of the state
should we in fact be validating when hw/uapi.enable==false.
And should we even be doing the uapi->hw copy when
uapi.enable==false? So far I've not been able to come up with
satisfactory answers for myself, so I'm putting it off for the
moment.

Cc: Lee Shawn C <shawn.c.lee@intel.com>
Fixes: 0aa5c3835c8a ("drm/i915: support two CSC module on gen11 and later")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2964
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205202322.27608-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Remove dead code from skl_pipe_wm_get_hw_state()

There is nothing else to be executed after this if block.

Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210212182201.155043-2-jose.souza@intel.com

drm/i915: Enable -Wuninitialized

-Wunintialized was disabled in commit c5627461490e ("drm/i915: Disable
-Wuninitialized") because there were two warnings that were false
positives. The first was due to DECLARE_WAIT_QUEUE_HEAD_ONSTACK, which
was fixed in LLVM 9.0.0. The second was in busywait_stop, which was
fixed in LLVM 10.0.0 (issue 415). The kernel's minimum version for LLVM
is 10.0.1 so this warning can be safely enabled, where it has already
caught a couple bugs.

Link: https://github.com/ClangBuiltLinux/linux/issues/220
Link: https://github.com/ClangBuiltLinux/linux/issues/415
Link: https://github.com/ClangBuiltLinux/linux/issues/499
Link: https://github.com/llvm/llvm-project/commit/2e040398f8d691cc378c1abb098824ff49f3f28f
Link: https://github.com/llvm/llvm-project/commit/c667cdc850c2aa821ffeedbc08c24bc985c59edd
Fixes: c5627461490e ("drm/i915: Disable -Wuninitialized")
References: 2ea4a7ba9bf6 ("drm/i915/gt: Avoid uninitialized use of rpcurupei in frequency_show")
References: 2034c2129bc4 ("drm/i915/display: Ensure that ret is always initialized in icl_combo_phy_verify_state")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20210216212953.24458-1-nathan@kernel.org

drm/i915: s/dev_priv/i915/ for the remainder of DDI clock routing

Convert the remaining 'dev_priv's to 'i915's in the DDI
clock routing functions.

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-16-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>

drm/i915: Relocate icl_sanitize_encoder_pll_mapping()

Move icl_sanitize_encoder_pll_mapping() out from the middle
of the .{enable,disable}_clock() functions.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-15-ville.syrjala@linux.intel.com

drm/i915: Use .disable_clock() for pll sanitation

Instead of every new platform having yet another masive
copy of the whole PLL sanitation code, let's just reuse the
.disable_clock() hook for this purpose. We do need to plug
this into the ICL+ DSI code for that, but fortunately it
already has a suitable function we can use.

We do lose the debug message though on account of not bothering
to check if the clock is actually enabled or not before turning
it off. We could introduce yet another vfunc to query the current
state, but not sure it's worth the hassle?

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-14-ville.syrjala@linux.intel.com

drm/i915: Split adl-s/rkl from icl_ddi_combo_{enable,disable}_clock()

Since .{enable,disable}_clock() are already vfuncs it's a bit silly to
have if-ladders inside them. Just provide specialized version for adl-s
and rkl so we don't need any of that.

v2: s/dev_priv/i915/ (Lucas)
    Fix typos in platform names (Lucas)

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-13-ville.syrjala@linux.intel.com

drm/i915: Extract _cnl_ddi_{enable,disable}_clock()

All the DPCLKA_CFGCR handling follows a common pattern. Let's
extract that to a small helper that just takes a few parameters
each caller can customize.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-12-ville.syrjala@linux.intel.com

drm/i915: Sprinkle WARN(!pll) into icl/dg1 .clock_enable()

The other DDI .enable_clock() functions are trying to protect us
against pll==NULL. A bit tempted to throw out all the WARNs as
just unnecessary noise, but I guess they might have some use
when poking around the shared_dpll code (not sure it wouldn't
oops elsewhere though). So let's unify it all and sprinkle in
the missing WARNs for icl/dg1.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-11-ville.syrjala@linux.intel.com

drm/i915: Sprinkle a few missing locks around shared DDI clock registers

The current code attempts to protect the RMWs into global
clock routing registers with a mutex, but forgets to do so
in a few places. Let's remedy that.

Note that at the moment we serialize all modesets onto single
wq, so this shouldn't actually matter. But maybe one day we
wish to attempt parallel modesets again...

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-10-ville.syrjala@linux.intel.com

drm/i915: Use intel_de_rmw() for DDI clock routing

The DDI clock routing programming is riddled with shared
registers, forcing us to do a lot of RMW. Switch over to
intel_de_rmw() to make that a bit less obnoxious.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-9-ville.syrjala@linux.intel.com

drm/i915: Extract icl+ .{enable,disable}_clock() vfuncs

For ICL+ we have several styles of clock routing for DDIs:
1) TC DDI + TC PHY
   -> needs DDI_CLK_SEL==MG/TBT part form intel_ddi_clk_{select,disable}()
   and ICL_DPCLKA_CFGCR0_TC_CLK_OFF part form icl_{map,unmap}_plls_to_ports()
2) ICL/TGL combo DDI + combo PHY
   -> just need the stuff from icl_{map,unmap}_plls_to_ports()
3) JSL/EHL TC DDI + combo PHY
   -> needs DDI_CLK_SEL==MG part from intel_ddi_clk_{select,disable}() and
   the full combo style clock selection from icl_{map,unmap}_plls_to_ports()
4) ADLS/RKL
   -> these use both TC and combo DDIs with combo PHYs, however they
   always use the full combo style clock selection as per
   icl_{map,unmap}_plls_to_ports() and do not use DDI_CLK_SEL at all,
   thus get treated the same as 2)

We extract all that from the current mess in the following way:
1) icl_ddi_tc_{enable,disable}_clock()
2) icl_ddi_combo_{enable,disable}_clock()
3) jsl_ddi_tc_{enable,disable}_clock()
4) for now we reuse icl_ddi_combo_{enable,disable}_clock() here

v2: s/dev_priv/i915/ (Lucas)

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-8-ville.syrjala@linux.intel.com

drm/i915: Convert DG1 over to .{enable,disable}_clock()

Replace dg1_{map,unmap}_plls_to_ports() with the appropriate
encoder vfuncs. And let's relocate the disable function next to
the enable function while at it.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-7-ville.syrjala@linux.intel.com

drm/i195: Extract cnl_ddi_{enable,disable}_clock()

Extract the DDI clock routing for CNL into the new vfuncs.

v2: s/dev_priv/i915/ (Lucas)

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-6-ville.syrjala@linux.intel.com

drm/i915: Extract skl_ddi_{enable,disable}_clock()

Extract the DDI clock routing clode for skl/derivatives
into the new encoder vfuncs.

v2: s/dev_priv/i915/ (Lucas)

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-5-ville.syrjala@linux.intel.com

drm/i915: Extract hsw_ddi_{enable,disable}_clock()

Yank out the HSW/BDW code from intel_ddi_clk_{select,disable}()
and put it into the new encoder .{enable,disable}_clock() vfuncs.

v2: s/dev_priv/i915/ (Lucas)
v3: Deal with FDI

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-4-ville.syrjala@linux.intel.com

drm/i915: Introduce .{enable,disable}_clock() encoder vfuncs

The current code dealing with the clock routing for DDI encoders
is a maintenance nightmare. Let's start cleaning it up by allowing
the encoder to provide vfuncs for enablign/disabling the clock.

We leave them initially unimplemented, falling back to the old
if-else approach.

v2: Convert the FDI enable sequence

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-3-ville.syrjala@linux.intel.com

drm/i915: Use intel_ddi_clk_select() for FDI

We want to put all DDI clock routing code into one place.
Unify the FDI enable sequence to use the standard function
instead of hand rolling its own. The disable sequence already
uses the normal thing.

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-2-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>

drm/i915: move intel_init_audio_hooks inside display

intel_init_audio_hooks() sets up hooks in the display struct and only
makes sense when we have display. Move it inside
intel_init_display_hooks() so it isn't called when we don't have
display.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20210213042756.953007-4-lucas.demarchi@intel.com

drm/i915/display: move register functions to display/

Now that all display-related functions are grouped in
i915_driver_register(), move them to display/ so we reduce the amount of
display calls from the rest of the driver.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20210213042756.953007-3-lucas.demarchi@intel.com

drm/i915: group display-related register calls

intel_gt_driver_register() may be called earlier than
intel_opregion_register() and acpi_video_register(), so move it up.

intel_display_debugfs_register() may be called later, together with the
other display-related initializations. There is a slight change in
behavior that sysfs files will show up before the display-related
debugfs files, but that shouldn't be a problem - userspace shouldn't be
relying in debugfs.

This allows us to group all the display-related calls under a single
check for "HAS_DISPLAY()" that can be later moved to a better place.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20210213042756.953007-2-lucas.demarchi@intel.com

drm/i915: stop registering if drm_dev_register() fails

If drm_dev_register() fails there is no reason to continue registering
the driver and initializing.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20210213042756.953007-1-lucas.demarchi@intel.com

drm/i915: Try to detect sudden loss of MMIO access

In rare circumstances bugs in PCI programming, broken BIOS, or failing
hardware can cause the CPU to lose access to the MMIO BAR on dgfx
platforms.  This is a pretty catastrophic failure since all register
reads come back with values of 0xFFFFFFFF.  Let's check for this special
case while doing our usual checks for unclaimed registers; the FPGA_DBG
register we use for those checks on modern platforms has some unused
bits that will always read back as 0 when things are behaving properly;
we can use them as canaries to detect when MMIO itself has suddenly
broken and try to print a more informative error message in the logs.

v2: Let the detection function still return 'true' if we've lost our
    MMIO access.  We'll still get an extra false positive message about
    an unclaimed register access, but we'll still honor the 'mmio_debug'
    limit and not spam the log.  (Lucas)

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210212211925.3418280-2-matthew.d.roper@intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>

drm/i915: FPGA_DBG is display-specific

Although the bspec's description doesn't make it very clear, the
hardware architects have confirmed that the FPGA_DBG register that we
use to check for unclaimed MMIO accesses is display-specific and will
only properly flag unclaimed MMIO transactions for registers in the
display range.  If a platform doesn't have display, FPGA_DBG itself will
not be available and should not be checked.  Let's move the feature flag
into intel_device_info.display to more accurately reflect this.

Given that we now know FPGA_DBG is display-specific, it could be argued
that we should only check it on out intel_de_*() functions.  However
let's not make that change right now; keeping the checks in all of the
existing locations still helps us catch cases where regular
intel_uncore_*() functions use bad MMIO offset math / base addresses and
accidentally wind up landing within an unused area within the display
MMIO range.  It will also help catch cases where userspace-initiated
MMIO (e.g., IGT's intel_reg tool) attempt to read bad offsets within the
display range.

v2:  Add missing hunk with the update to the HAS_FPGA_DBG_UNCLAIMED
     macro.  (CI)

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210212222049.3516344-1-matthew.d.roper@intel.com

drm/i915/gen9_bc: Add W/A for missing STRAP config on TGP PCH + CML combos

Apparently the new gen9_bc platforms that Intel has introduced don't
provide us with a STRAP config register to read from for initializing DDI
B, C, and D detection. So, workaround this by hard-coding our strap config
in intel_setup_outputs().

Changes since v4:
* Split this into it's own commit

Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
[originally from Tejas's work]
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209212832.1401815-5-lyude@redhat.com

drm/i915/gen9_bc: Introduce HPD pin mappings for TGP PCH + CML combos

Next, let's start introducing the HPD pin mappings for Intel's new gen9_bc
platform in order to make hotplugging display connectors work. Since
gen9_bc is just a TGP PCH along with a CML CPU, except with the same HPD
mappings as ICL, we simply add a skl_hpd_pin function that is shared
between gen9 and gen9_bc which handles both the traditional gen9 HPD pin
mappings and the Icelake HPD pin mappings that gen9_bc uses.

Changes since v4:
* Split this into its own commit
* Introduce skl_hpd_pin() like vsyrjala suggested and use that instead of
  sticking our HPD pin mappings in TGP code

Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
[originally from Tejas's work]
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209212832.1401815-4-lyude@redhat.com

i915/perf: Drop the check for report reason in OA

After fixing the OA_TAIL_PTR corruption, there are no more reports with
reason field of zero. Drop the check for report reason.

Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210210190106.8586-1-umesh.nerlige.ramappa@intel.com

drm/i915/debugfs: HDCP capability enc NULL check

DP-MST connector encoder initializes at modeset
Adding a connector->encoder NULL check in order to
avoid any NULL pointer dereference.
intel_hdcp_enable() already handle this but debugfs
can also invoke the intel_{hdcp,hdcp2_capable}.
Handling it gracefully.

v2:
- Use necessary lock and NULL check in
  i915_hdcp_sink_capability_show. [Imre]

Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210211140502.22786-1-anshuman.gupta@intel.com

drm/i915/display: fix comment on skl straps

We are not checking for specific SKUs and feedback from HW team is that
it may not work since it was supposed to be fixed by the same time
straps stopped to be used. So, just update comment.

v2: Instead of removing the check, just update the comment since
feedback from HW team was that it actually may not work

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200625001120.22810-3-lucas.demarchi@intel.com

drm/i915/gen9_bc: Introduce TGP PCH DDC pin mappings

With the introduction of gen9_bc, where Intel combines Cometlake CPUs with
a Tigerpoint PCH, we'll need to introduce new DDC pin mappings for this
platform in order to make all of the display connectors work. So, let's do
that.

Changes since v4:
* Split this into it's own patch - vsyrjala
Changes since v5:
* Rename gen9bc_port_to_ddc_pin() to gen9bc_tgp_port_to_ddc_pin()

Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
[originally from Tejas's work]
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209212832.1401815-3-lyude@redhat.com

drm/i915/gen9_bc: Recognize TGP PCH + CML combos

Since Intel has introduced the gen9_bc platform, a combination of
Tigerpoint PCHs and CML CPUs, let's recognize such platforms as valid and
avoid WARNing on them.

Changes since v4:
* Split this into it's own patch - vsyrjala

Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
[originally from Tejas's work]
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209212832.1401815-2-lyude@redhat.com

drm/i915/display: Handle lane polarity for DDI port

Lane Reversal is required for some of the DDI ports. This information
is populated in VBT and driver should read the same and set the
polarity while enabling the port. This patch handles the same.

It helps fix a display blankout issue on DP ports on certain
platforms.

Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210211114209.23866-1-uma.shankar@intel.com

drm/i915/display: Add DDR5 and LPDDR5 BW buddy page entries

Set the right BW buddy page mask for new memory types.

BSpec: 49218
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209174238.153278-1-jose.souza@intel.com

drm/i915: Warn when releasing a frontbuffer while in use

Let's scream if we are about to release a frontbuffer which
is still in use.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209021918.16234-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Fix overlay frontbuffer tracking

We don't have a persistent fb holding a reference to the frontbuffer
object, so every time we do the get+put we throw the frontbuffer object
immediately away. And so the next time around we get a pristine
frontbuffer object with bits==0 even for the old vma. This confuses
the frontbuffer tracking code which understandably expects the old
frontbuffer to have the overlay's bit set.

Fix this by hanging on to the frontbuffer reference until the next
flip. And just to make this a bit more clear let's track the frontbuffer
explicitly instead of just grabbing it via the old vma.

Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1136
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209021918.16234-2-ville.syrjala@linux.intel.com
Fixes: 8e7cb1799b4f ("drm/i915: Extract intel_frontbuffer active tracking")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Disallow plane x+w>stride on ilk+ with X-tiling

ilk+ planes get notably unhappy when the plane x+w exceeds
the stride. This wasn't a problem previously because we
always aligned SURF to the closest tile boundary so the
x offset never got particularly large. But now with async
flips we have to align to 256KiB instead and thus this
becomes a real issue.

On ilk/snb/ivb it looks like the accesses just wrap
early to the next tile row when scanout goes past the
SURF+n*stride boundary, hsw/bdw suffer more heavily and
start to underrun constantly. i965/g4x appear to be immune.
vlv/chv I've not yet checked.

Let's borrow another trick from the skl+ code and search
backwards for a better SURF offset in the hopes of getting the
x offset below the limit. IIRC when I ran into a similar issue
on skl years ago it was causing the hardware to fall over
pretty hard as well.

And let's be consistent and include i965/g4x in the check
as well, just in case I just got super lucky somehow when
I wasn't able to reproduce the issue. Not that it really
matters since we still use 4k SURF alignment for i965/g4x
anyway.

Fixes: 6ede6b0616b2 ("drm/i915: Implement async flips for vlv/chv")
Fixes: 4bb18054adc4 ("drm/i915: Implement async flip for ilk/snb")
Fixes: 2a636e240c77 ("drm/i915: Implement async flip for ivb/hsw")
Fixes: cda195f13abd ("drm/i915: Implement async flips for bdw")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209021918.16234-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/tgl+: Make sure TypeC FIA is powered up when initializing it

The TypeC FIA can be powered down if the TC-COLD power state is allowed,
so block the TC-COLD state when initializing the FIA.

Note that this isn't needed on ICL where the FIA is never modular and
which has no generic way to block TC-COLD (except for platforms with a
legacy TypeC port and on those too only via these legacy ports, not via
a DP-alt/TBT port).

Cc: <stable@vger.kernel.org> # v5.10+
Cc: José Roberto de Souza <jose.souza@intel.com>
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3027
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210208154303.6839-1-imre.deak@intel.com
Reviewed-by: Jos� Roberto de Souza <jose.souza@intel.com>

i915/perf: Add additional OA formats for gen12

Gen12 supports additional OA formats as compared to what was added
earlier. Include the additional OA formats.

Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210208174029.45621-3-umesh.nerlige.ramappa@intel.com

i915/perf: Move OA formats to single array

Variations in OA formats in the different gens has led to creation of
several sparse arrays to store the formats.

Move oa formats into a single array and format_mask to check for
platform specific oa formats.

Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210208174029.45621-2-umesh.nerlige.ramappa@intel.com

i915/perf: Store a mask of valid OA formats for a platform

Validity of an OA format is checked by using a sparse array of formats
per gen. Instead maintain a mask of supported formats for a platform in
the perf object.

v2: Use set_bit and test_bit style for the format_mask (Chris)

Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210208174029.45621-1-umesh.nerlige.ramappa@intel.com

drm/i915/rkl: Remove require_force_probe protection

Removing force probe protection from RKL platform. Did
not observe warnings, errors, flickering or any visual
defects while doing ordinary tasks like browsing and
editing documents in a two monitor setup.

Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130124855.319226-1-tejaskumarx.surendrakumar.upadhyay@intel.com

drm/i915: Fix HAS_LSPCON macro for platforms between GEN9 and GEN10

Legacy LSPCON chip from MCA and Parade is only used for platforms
between GEN9 and GEN10. Fixing the HAS_LSPCON macro to reflect the same.

Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210208055554.24357-1-ankit.k.nautiyal@intel.com

drm/i915: refactor skylake scaler code into new file.

This moves the code from various places and consolidates it
into one new file.

v2:
- rename skl_program_plane -> skl_program_plane_scaler (Ville)
- also move skl_pfit_enable, and consequently make some skl_scaler_*
  functions static to skl_scaler.c (Ville)

Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2fa703ffc7b96a41c392fd5ebbd2e6e4ffb6fb05.1612536383.git.jani.nikula@intel.com

drm/i915: migrate i9xx plane get config

Migrate this code out like the skylake code.

Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c003bd458a6bcc703e9e2fb05731fb7124012e8c.1612536383.git.jani.nikula@intel.com

drm/i915: migrate pll enable/disable code to intel_dpll.[ch]

This moves the older i9xx/vlv/chv enable/disable to dpll file.

Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7fa8c76b0f07f3ede9efd7c1f989f33fbc8c53a3.1612536383.git.jani.nikula@intel.com

drm/i915: move is_ccs_modifier to an inline

There is no need for this to be out of line.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/bb73a151b7b780f927edeb7e121449446592805d.1612536383.git.jani.nikula@intel.com

drm/i915: split fb scalable checks into g4x and skl versions

This just cleans these up a bit.

Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c91d924e93965515d2017dbf3c89c245ff6d52ea.1612536383.git.jani.nikula@intel.com

drm/i915: move pipe update code into crtc. (v2)

Daniel suggested this should move here.

v2: move vrr code.

Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/738c7aaeb63c7d2357ddd932f18787ec8a3cefeb.1612536383.git.jani.nikula@intel.com

drm/i915: migrate skl planes code new file (v5)

Rework the plane init calls to do the gen test one level higher.

Rework some of the plane helpers so they can live in new file,
there is still some scope to clean up the plane/fb interactions
later.

v2: drop atomic code back, rename file to Ville suggestions,
add header file.
v3: move scaler bits back
v4: drop wrong new includes (Ville)
v5: integrate the ccs gen12 changes
v6: fix unrelated code movement (Ville)

Signed-off-by: Dave Airlie <airlied@redhat.com>
[Jani: fixed up sparse warnings.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4e88a5c6b9ab3b93cc2b6c7d78c26ae86f6abbd0.1612536383.git.jani.nikula@intel.com

drm/i915: Use intel_hdmi_port_clock() more

Replace the hand rolled intel_hdmi_port_clock() stuff
with the real thing.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210204020846.2094-2-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>

drm/i915: Index min_{cdclk,voltage_level}[] with pipe

min_cdclk[] and min_voltage_level[] are supposed to be indexed
with the pipe. Fix up a few cases where we index via the crtc
index (via the atomic iterators) instead.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210204020846.2094-1-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>

drm/i915: migrate hsw fdi code to new file.

Daniel asked for this, but it's a bit messy and I'm not sure
how best to clean it up yet.

Signed-off-by: Dave Airlie <airlied@redhat.com>
[Jani: also moved fdi buf trans to intel_fdi.c.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/44491f2465549ea5c2e48cde5437fa232f77ab96.1612467466.git.jani.nikula@intel.com

drm/i915: refactor ddi translations into a separate file (v2)

Ville suggested this, these tables are probably better being
standalone.

This fixes up the cnl/bxt interfaces to be like the others,
the intel one I left alone since it has a few extra entrypoints.

v2: add back missing rocketlake bits.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
[Jani: made some functions static]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/def9eed2581d71863ccdf35f323b525facc2482c.1612467466.git.jani.nikula@intel.com

drm/i915: Make psr_safest_params and enable_psr2_sel_fetch parameters read only

By mistake those 2 parameters were defined as read and write in the
.h file while in the .c file it is read only.
The intention here was to be read only to avoid the need of additional
handling.

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Petri Latvala <petri.latvala@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210204153357.39681-1-jose.souza@intel.com

drm/i915/display: Remove PSR2 on JSL and EHL

While JSL and EHL eDP transcoder supports PSR2, the phy of this
platforms only supports eDP 1.3, so removing PSR2 support as this
feature was added in eDP 1.4.

Signed-off-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210204175830.97857-1-jose.souza@intel.com

drm/i915/display: Support Multiple Transcoders' PSR status on debugfs

In order to support the PSR state of each transcoder, it adds
i915_psr_status to sub-directory of each transcoder.

v2: Change using of Symbolic permissions 'S_IRUGO' to using of octal
    permissions '0444'
v5: Addressed JJani Nikula's review comments
 - Remove checking of Gen12 for i915_psr_status.
 - Add check of HAS_PSR()
 - Remove meaningless check routine.

Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210204134015.419036-2-gwan-gyeong.mun@intel.com

drm/i915/display: Support PSR Multiple Instances

It is a preliminary work for supporting multiple EDP PSR and
DP PanelReplay. And it refactors singleton PSR to Multi Transcoder
supportable PSR.
And this moves and renames the i915_psr structure of drm_i915_private's to
intel_dp's intel_psr structure.
It also causes changes in PSR interrupt handling routine for supporting
multiple transcoders. But it does not change the scenario and timing of
enabling and disabling PSR. And it not support multiple pipes with
a single transcoder PSR case yet.

v2: Fix indentation and add comments
v3: Remove Blank line
v4: Rebased
v5: Rebased and Addressed Anshuman's review comment.
    - Move calling of intel_psr_init() to intel_dp_init_connector()
v6: Address Anshuman's review comments
   - Remove wrong comments and add comments for a limit of supporting of
     a single pipe PSR
v7: Update intel_psr_compute_config() for supporting multiple transcoder
    PSR on BDW+
v8: Address Anshuman's review comments
   - Replace DRM_DEBUG_KMS with drm_dbg_kms() / DRM_WARN with drm_warn()
v9: Fix commit message
v10: Rebased
v11: Address Jose's review comment.
  - Reorder calling order of intel_psr2_program_trans_man_trk_ctl().
  - In order to reduce changes keep the old name for drm_i915_private.
  - Change restrictions of multiple instances of PSR.
v12: Address Jose's review comment.
  - Change the calling of intel_psr2_program_trans_man_trk_ctl() into
    commit_pipe_config().
  - Change a checking order of CAN_PSR() and connector_status to original
    on i915_psr_sink_status_show().
  - Drop unneeded intel_dp_update_pipe() function.
  - In order to wait a specific encoder which belong to crtc_state on
    intel_psr_wait_for_idle(), add checking of encoder.
  - Add an whitespace to comments.
v13: Rebased and Address Jose's review comment.
  - Add and use for_each_intel_psr_enabled_encoder() macro.
  - In order to use correct frontbuffer_bit for each pipe,
    fix intel_psr_invalidate() and intel_psr_flush().
  - Remove redundant or unneeded codes.
  - Update comments.
v14: Address Jose's review comment
  - Add and use for_each_intel_encoder_can_psr() macro and
    for_each_intel_encoder_mask_can_psr() macro.
  - Add source_support member variable into intel_psr structure.
  - Update CAN_PSR() macro that checks source_support.
  - Move encoder's PSR availity check to psr_init() from
    psr_compute_config().
  - Remove redundant or unneeded codes.
v15: Remove wrong mutex lock/unlock of PSR from
     intel_psr2_program_trans_man_trk_ctl()

Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210204134015.419036-1-gwan-gyeong.mun@intel.com

drm/i915/display: support ddr5 mem types

Add DDR5 and LPDDR5 return values from punit fw.

BSPEC: 54023
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210204200458.21875-1-clinton.a.taylor@intel.com

drm/i915: Reject 446-480MHz HDMI clock on GLK

The BXT/GLK DPLL can't generate certain frequencies. We already
reject the 233-240MHz range on both. But on GLK the DPLL max
frequency was bumped from 300MHz to 594MHz, so now we get to
also worry about the 446-480MHz range (double the original
problem range). Reject any frequency within the higher
problematic range as well.

Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3000
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210203093044.30532-1-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>

drm/i915: Disable runtime power management during shutdown

At least on some TGL platforms PUNIT wants to access some display HW
registers, but it doesn't handle display power management (disabling DC
states as required) and so this register access will lead to a hang. To
prevent this disable runtime power management for poweroff and reboot.

v2:
- Add code comment clarifying the requirement of display power states.
  (Ville)

Reported-and-tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210127181909.128094-1-imre.deak@intel.com

drm/i915/display: fix spelling mistake "Couldnt" -> "Couldn't"

There is a spelling mistake in a drm_dbg message. Fix it.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210203110803.17894-1-colin.king@canonical.com

Merge tag 'topic/drm-device-pdev-2021-02-02' of git://anongit.freedesktop.org/drm/drm-intel into drm-intel-next

Driver Changes:
- drm/i915: Remove references to struct drm_device.pdev

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87y2g6fxxv.fsf@intel.com

drm/i915/gvt: Remove references to struct drm_device.pdev

Using struct drm_device.pdev is deprecated. Convert i915 to struct
drm_device.dev. No functional changes.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128133127.2311-4-tzimmermann@suse.de

drm/i915/gt: Remove references to struct drm_device.pdev

Using struct drm_device.pdev is deprecated. Convert i915 to struct
drm_device.dev. No functional changes.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128133127.2311-3-tzimmermann@suse.de

drm/i915: Remove references to struct drm_device.pdev

Using struct drm_device.pdev is deprecated. Convert i915 to struct
drm_device.dev. No functional changes.

v6:
* also remove assignment in selftests/ in a later patch (Chris)
v5:
* remove assignment in later patch (Chris)
v3:
* rebased
v2:
* move gt/ and gvt/ changes into separate patches

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128133127.2311-2-tzimmermann@suse.de

Merge tag 'topic/adl-s-enabling-2021-02-01-1' of git://anongit.freedesktop.org/drm/drm-intel into drm-intel-next

Driver Changes:
  - Add basic support for Alder Lake S, to be shared between
  drm-intel-next and drm-intel-gt-next

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
# Conflicts:
# drivers/gpu/drm/i915/i915_drv.h
From: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210202025620.2212559-1-lucas.demarchi@intel.com

drm/i915/adl_s: Add GT and CTX WAs for ADL-S

- Extend Wa_1606931601 and Wa_1409804808 to ADL-S.
- Extend Wa_14010919138 and Wa_14010229206 to ADL-S (Madhumitha)
- Extend Wa_22010271021 to ADLS (cyokoyam)

v2:
- Extend Wa_1409804808 and remove unnecessary branching/redundant
  adls workaround placeholder functions.
- Split WAs properly based on previous platforms and applicable ADLS
  WA.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Madhumitha Tolakanahalli Pradeep <madhumitha.tolakanahalli.pradeep@intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210129182945.217078-9-aditya.swarup@intel.com

drm/i915/adl_s: Add display WAs for ADL-S

- Extend permanent driver WA Wa_1409767108, Wa_14010685332
  and Wa_14011294188 to adl-s.
- Extend permanent driver WA Wa_1606054188 to adl-s.
- Add Wa_14011765242 for adl-s A0 stepping.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210129182945.217078-8-aditya.swarup@intel.com

drm/i915/adl_s: Update memory bandwidth parameters

Just like RKL, the ADL_S platform also has different memory
characteristics from past platforms.  Update the values used
by our memory bandwidth calculations accordingly.

v2: Fix minor nitpick for shifting ADLS case above RKL(based on platform
order).(mdroper)

Bspec: 64631
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210129182945.217078-7-aditya.swarup@intel.com

drm/i915/adl_s: Load DMC

Load DMC on ADL_S v2.01. This is the first offcial
release of DMC for ADL_S.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210129182945.217078-6-aditya.swarup@intel.com

drm/i915/display: Add HAS_D12_PLANE_MINIMIZATION

- As RKL and ADL-S only have 5 planes, primary and 4 sprites and
  the cursor plane, let's group the handling together under
  HAS_D12_PLANE_MINIMIZATION.
- Also use macro to select pipe irq fault error mask.

BSpec: 49251
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210129182945.217078-5-aditya.swarup@intel.com

drm/i915/adl_s: Re-use TGL GuC/HuC firmware

ADL-S, like RKL, uses the same internal device ID for the GuC and HuC as
TGL did, making them all firmware-compatible.  Let's re-use TGL's
firmware for ADL-S.

Bspec: 50668
Cc: John Harrison <John.C.Harrison@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210129182945.217078-4-aditya.swarup@intel.com

drm/i915/adl_s: Add power wells

TGL power wells can be re-used for ADL-S with the exception of the fake
power well for TC_COLD, just like DG-1.

BSpec: 53597
Bspec: 49231

Cc: Imre Deak <imre.deak@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210129182945.217078-3-aditya.swarup@intel.com

drm/i915/adl_s: Update PHY_MISC programming

ADL-S switches up which PHYs are considered a master to other PHYs;
PHY-C is no longer a master, but PHY-D is now.

Bspec: 49291
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210129182945.217078-2-aditya.swarup@intel.com

drm/i915/bios: tidy up child device debug logging

Make the child device details easier to read by turning this:

[drm:parse_ddi_port [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
[drm:parse_ddi_port [i915]] VBT HDMI level shift for port B: 8
[drm:parse_ddi_port [i915]] VBT DP max link rate for port B: 810000
[drm:parse_ddi_port [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
[drm:parse_ddi_port [i915]] VBT HDMI level shift for port C: 8
[drm:parse_ddi_port [i915]] VBT (e)DP boost level for port C: 3
[drm:parse_ddi_port [i915]] VBT HDMI boost level for port C: 1
[drm:parse_ddi_port [i915]] VBT DP max link rate for port C: 810000

into this:

[drm:parse_ddi_port [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
[drm:parse_ddi_port [i915]] Port B VBT HDMI level shift: 8
[drm:parse_ddi_port [i915]] Port B VBT DP max link rate: 810000
[drm:parse_ddi_port [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
[drm:parse_ddi_port [i915]] Port C VBT HDMI level shift: 8
[drm:parse_ddi_port [i915]] Port C VBT (e)DP boost level: 3
[drm:parse_ddi_port [i915]] Port C VBT HDMI boost level: 1
[drm:parse_ddi_port [i915]] Port C VBT DP max link rate: 810000

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210127084534.24406-1-jani.nikula@intel.com

drm/i915/hdcp: disable the QSES check for HDCP2.2 over MST

Like the patch to disable QSES for HDCP 1.4 over MST
https://patchwork.freedesktop.org/patch/415297/ the HDCP2.2 spec
doesn't require QSES as well and we've seen QSES not supported on a
couple HDCP2.2 docks so far (Dell WD19 and Lenovo LDC-G2)

Remove it for now until we get a better idea of how widely supported
QSES is and how to support it optionally.

Signed-off-by: Juston Li <juston.li@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210127065034.2501119-4-juston.li@intel.com

drm/i915: Don't check tc_mode unless dealing with a TC PHY

We shouldn't really trust tc_mode on non-TC PHYs since we never
initialize it explicitly. So let's check for the PHY type first.
Fortunately TC_PORT_TBT_ALT happens to be zero so I don't think
there's an actual bug here, just a possibility for a future one
if someone rearranges the enum values.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128155948.13678-5-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Move HDMI vswing programming to the right place

The documented programming sequence indicates the correct point
for the vswing programming is just before we enable the DDI.
Make it so.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128155948.13678-4-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Power up combo PHY lanes for for HDMI as well

Currently we only explicitly power up the combo PHY lanes
for DP. The spec says we should do it for HDMI as well.

Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128155948.13678-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Extract intel_ddi_power_up_lanes()

Reduce the copypasta by pulling the combo PHY lane
power up stuff into a helper. We'll have a third user soon.

Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128155948.13678-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Skip vswing programming for TBT

In thunderbolt mode the PHY is owned by the thunderbolt controller.
We are not supposed to touch it. So skip the vswing programming
as well (we already skipped the other steps not applicable to TBT).

Touching this stuff could supposedly interfere with the PHY
programming done by the thunderbolt controller.

Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128155948.13678-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915/dp: Prevent setting the LTTPR LT mode if no LTTPRs are detected

Atm, the driver programs explicitly the default transparent link
training mode (0x55) to DP_PHY_REPEATER_MODE even if no LTTPRs are
detected.

This conforms to the spec (3.6.6.1):
"DP upstream devices that do not enable the Non-transparent mode of
 LTTPRs shall program the PHY_REPEATER_MODE register (DPCD Address
 F0003h) to 55h (default) prior to link training"

however writing the default value to this DPCD register seems to cause
occasional link training errors at least for a DELL WD19TB TBT dock, when
no LTTPRs are detected.

Writing to DP_PHY_REPEATER_MODE will also cause an unnecessary timeout
on systems without any LTTPR.

To fix the above two issues let's assume that setting the default mode
is redundant when no LTTPRs are detected. Keep the existing behavior and
program the default mode if more than 8 LTTPRs are detected or in case
the read from DP_PHY_REPEATER_CNT returns an invalid value.

References: https://gitlab.freedesktop.org/drm/intel/-/issues/2801
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210118183143.1145707-1-imre.deak@intel.com