OSDN Git Service
Olof Johansson [Fri, 25 May 2018 21:33:36 +0000 (14:33 -0700)]
Merge tag 'qcom-dts-for-4.18' of git://git./linux/kernel/git/agross/linux into next/dt
Qualcomm Device Tree Changes for v4.18
* APQ8064 fixes for irq translations and pci address translation
* Fix RPM clock controller compatible on MSM8660
* Add TZ and SMEM reserved regions on IPQ4019
* Add vadc nodes for PM8941
* Disable i2c by default at top level APQ8064 dtsi
* tag 'qcom-dts-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: dts: qcom-apq8064: use correct pci address for address translation
ARM: dts: qcom-apq8064: fix gic_irq_domain_translate warnings
ARM: dts: Fix the RPM clock controller compatible string
ARM: dts: ipq4019: Add TZ and SMEM reserved regions
ARM: dts: qcom: pm8941: Add vadc nodes needed to estimate an ocv
ARM: dts: qcom-apq8064: disable i2c by default at soc dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 21:32:58 +0000 (14:32 -0700)]
Merge tag 'qcom-arm64-for-4.18' of git://git./linux/kernel/git/agross/linux into next/dt
Qualcomm ARM64 Updates for v4.18
* Add support for SDM845 and associated peripherals
* Fix gic_irq_domain_translation warnings on Qualcomm platforms
* Add binding for GENI SE, Qualcomm bluetooth, and Command DB
* Add support for SDHCI and ramoops on MSM8992
* Fixup qcom,pcie devices to pcie
* Add wlan, bluetooth, and micro SD supplies on db820c
* Add UFS related nodes on MSM8996
* tag 'qcom-arm64-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: qcom: msm8996: Add ufs related nodes
arm64: dts: msm8996: fix gic_irq_domain_translate warnings
arm64: dts: qcom: sdm845: Sort nodes in the soc by address
arm64: dts: qcom: sdm845: Sort nodes in the reserved mem by address
arm64: dts: sdm845: Add command DB node
arm64: dts: sdm845: Fix xo_board clock name and speed
arm64: dts: qcom: Add SDM845 SMEM nodes
arm64: dts: qcom: Add APSS shared mailbox node to SDM845
arm64: dts: msm8916: fix gic_irq_domain_translate warnings
dt-bindings: introduce Command DB for QCOM SoCs
arm64: dts: apq8096-db820c: Add micro sd card supplies
dt-bindings: soc: qcom: Add device tree binding for GENI SE
dt-bindings: net: bluetooth: Add qualcomm-bluetooth
arm64: dts: apq8096-db820c: enable bluetooth node
arm64: dts: apq8096-db820c: Enable wlan and bt en pins
arm64: dts: qcom: rename qcom,pcie devices to pcie
arm64: dts: msm8992: add pstore-ramoops support
arm64: dts: sdm845: Add minimal dts/dtsi files for sdm845 SoC and MTP
arm64: dts: Enable onboard SDHCI on msm8992
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 21:14:20 +0000 (14:14 -0700)]
Merge tag 'omap-for-v4.18/dt-part2-signed' of git://git./linux/kernel/git/tmlind/linux-omap into next/dt
Second set of dts changes for omap variants for v4.18 merge window
This series of changes contains fixes for already queued tps65218
IRQ_TYPE, and fixes for omap3 and am335x use of IRQ_TYPE. There are
also addition of oscillator clock for logicpd omap3 boards and a series
of changes to improve support for am3517-evm board. And there is also
a change to configure WLAN for am437x-sk-evm.
* tag 'omap-for-v4.18/dt-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (24 commits)
ARM: dts: am3517-evm: Add User LEDs and Pushbutton
ARM: dts: am3517-evm: Add I/O expander for User DIP switches and LEDS
ARM: dts: logicpd-som-lv: Fix Touchscreen controller
ARM: dts: am3517-som: Add Seiko Instruments RTC s35390a
ARM: dts: am437x-sk-evm: add wilink8 support
ARM: dts: am3517-evm: Add LCD panel type 15 support
ARM: dts: am3517-som: Associate cpu to regulator supply
ARM: dts: am3517-som: Add TI TPS65023 regulators
ARM: dts: am3517-evm: Split off SOM features from baseboard
ARM: dts: am3517: Add pinmuxing, CD and WP for MMC1
ARM: dts: logicpd-som-lv: Add fixed 26MHz clock as fck for twl
ARM: dts: logicpd-torpedo: Add fixed 26MHz clock as fck for twl
ARM: dts: omap3-pandora-common: Use IRQ_TYPE specifier
ARM: dts: am335x-boneblue: Use IRQ_TYPE specifier
ARM: dts: am335x-baltos.dtsi: Use IRQ_TYPE specifier
ARM: dts: am335x-baltos-ir5221: Use IRQ_TYPE specifier
ARM: dts: am335x-baltos-ir3220: Use IRQ_TYPE specifier
Revert "ARM: dts: am437x-sk-evm: Correct tps65218 irq type"
ARM: dts: am437x-epos-evm: Fixup (again) tps65218 irq type
ARM: dts: am437x-cm-t43: Fixup (again) tps65218 irq type
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 21:02:46 +0000 (14:02 -0700)]
Merge tag 'sunxi-dt64-for-4.18' of https://git./linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 changes for 4.18
We mostly have some changes to support the H6, Allwinner latest SoC. We're
still in the preliminary phase, with I2C, pinctrl and clock support.
* tag 'sunxi-dt64-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: h6: add PCF8563 RTC on Pine H64 board
arm64: allwinner: h6: add R_I2C controller
arm64: allwinner: h6: add R_INTC interrupt controller
arm64: allwinner: h6: add node for R_PIO pin controller
arm64: allwinner: h6: add PRCM CCU device node
arm64: dts: allwinner: a64: bananapi-m64: add usb otg
arm64: dts: allwinner: axp803: Add drivevbus regulator
arm64: allwinner: h6: restore the usage of CCU slice macros
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 20:58:59 +0000 (13:58 -0700)]
Merge tag 'sunxi-h3-h5-for-4.18' of https://git./linux/kernel/git/sunxi/linux into next/dt
Allwinner H3/H5 support for 4.18
Here is our usual bunch of changes for the H3 and H5 SoCs that share the
same SoC design but with different CPUs.
This time, most of the changes are about supporting CPUFreq on these SoCs,
with voltage scaling being enabled for a number of boards.
* tag 'sunxi-h3-h5-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: h3: Add SY8106A regulator to Orange Pi PC
arm64: dts: allwinner: Add dts file for Libre Computer Board ALL-H3-CC H5 ver.
arm64: dts: allwinner: Sort dtb entries in Makefile
arm64: dts: allwinner: h5: Add cpu0 label for first cpu
ARM: dts: sun8i: h2+: Add Libre Computer Board ALL-H3-CC H2+ ver.
ARM: dts: sun8i: h2-plus: Sort dtb entries in Makefile
arm: dts: sun8i: h3: libretech-all-h3-cc: Move board definition to common dtsi
ARM: dts: sun8i: h3: fix ALL-H3-CC H3 ver VCC-1V2 regulator voltage
ARM: dts: sun8i: h3: set the cpu-supply to VDD-CPUX on ALL-H3-CC H3 ver
ARM: dts: sun8i: h3: fix ALL-H3-CC H3 ver VDD-CPUX voltage
ARM: dts: sun8i: h3: add SY8113B regulator used by Orange Pi One board
ARM: dts: sun8i: h2+: add SY8113B regulator used by Orange Pi Zero board
ARM: dts: sun8i: h3: add operating-points-v2 table for CPU
ARM: dts: sunxi: h3/h5: Add r_i2c I2C controller
ARM: dts: sunxi: h3/h5: Add r_i2c pinmux node
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 20:54:36 +0000 (13:54 -0700)]
Merge tag 'sunxi-dt-for-4.18' of https://git./linux/kernel/git/sunxi/linux into next/dt
Allwinner DT additions for 4.18
Here is our usual bunch of DT changes for our arm SoCs, with most
significantly:
- MIPI-DSI support for the A33
- NAND support for the A33
- SMP support for the A83t
- GMAC support for the R40
- And some new boards: Olimex A20-SOM-EVB-eMMC, Nintendo NES and SuperNES
Classic
* tag 'sunxi-dt-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: Add Olimex A20-SOM-EVB-eMMC board
ARM: dts: sun8i: r40: bananapi-m2-ultra: Enable GMAC ethernet controller
ARM: dts: sun8i: r40: Add device node and RGMII pinmux node for GMAC
ARM: dts: sun8i: r40: bananapi-m2-ultra: Sort device node dereferences
ARM: dts: sun8i: Add enable-method for SMP support for the A83T SoC
ARM: dts: sun8i: a83t: Add CCI-400 node
ARM: dts: sun8i: Add R_CPUCFG device node for the A83T dtsi
ARM: dts: sun8i: Add CPUCFG device node for A83T dtsi
ARM: dts: nes: add Nintendo NES/SuperNES Classic Edition support
ARM: dts: sun8i: a23/a33: declare NAND pins
ARM: dts: sunxi: Add sid for a83t
ARM: dts: sun8i: a33: Add the DSI-related nodes
ARM: dts: sunxi: Change sun7i-a20-olimex-som204-evb to not use cd-inverted
ARM: sun8i: v40: enable USB host ports for Banana Pi M2 Berry
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 20:53:18 +0000 (13:53 -0700)]
Merge tag 'imx-dt64-4.18' of git://git./linux/kernel/git/shawnguo/linux into next/dt
Freescale arm64 device tree update for 4.18:
- Add unit address for ls208xa-rdb SPI flash node matching 'reg'
property to fix DTC warning unit_address_vs_reg.
- Use hypen instead of underscore in aliases name for fsl-ls1012a to
fix DTC warning alias_paths.
* tag 'imx-dt64-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: fsl-ls1012a: Fix DTC aliases warnings
arm64: dts: ls208xa-rdb: Pass unit name to SPI flash node
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 20:52:34 +0000 (13:52 -0700)]
Merge tag 'imx-dt-4.18' of git://git./linux/kernel/git/shawnguo/linux into next/dt
i.MX device tree update for 4.18:
- New boards support: BTicino i.MX6DL Mamoj board, DHCOM iMX6 SoM and
PDK2 board, Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit,
Kieback & Peter GmbH iMX6Q TPC board.
- A series from Anson Huang to add a bunch of devices for i.MX6SX
SabreAuto board, PMIC, IO expanders, FEC, Watchdog, LED and Touch.
- Update i.MX7D for cpufreq support, using operating-points-v2
bindings, correcting cpu supply name for voltage scaling.
- Clean up unneeded 'codec-handle' property from imx25-pdk and
imx53-tx53 device tree.
- Switch SoC dtsi and NXP board dts files to use SPDX identifier.
- Remove unnecessary '#address-cells/#size-cells' to fix DTC warning
avoid_unnecessary_addr_size seen with W=1 switch.
- A series from Rob Herring to fix DTC warning graph_endpoint seen with
IPU OF graph when W=1 switch is on.
- Update a few boards to use symbol name instead of hard-coding the
input codes.
- Update a number of boards to use IRQ_TYPE specifier instead of the
raw value.
- A few updates for i.MX6 RDU2 board: bumping SoC/PU operating points,
adding assigned clocks for GPU, and enabling eGalax touchscreen.
- A couple of i.MX51 RDU1 updates: limiting usbh1 to full-speed, and
cleaning up eMMC device node.
- Convert Hummingboard audio bindings from imx-audio-sgtl5000 to
simple-audio-card, so that auxiliary audio devices such as external
amplifiers can be supported.
- Replace underscore with hyphen in aliases name to fix DTC warning
alias_paths with W=1 switch.
- A couple of updates on i.MX7D SAI and i.MX6ULL UART5 pin defines.
- Other random and small changes.
* tag 'imx-dt-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (72 commits)
ARM: dts: imx28/imx53: enable edt-ft5x06 wakeup source
ARM: dts: imx51-zii-rdu1: cleanup eMMC node
ARM: dts: vf610-zii-dev: enable vf610 builtin temp sensor
ARM: dts: imx7d: use operating-points-v2 for cpu
ARM: dts: imx7s-warp: remove unnecessary cpu regulator supply
ARM: dts: imx7d: correct cpu supply name for voltage scaling
ARM: dts: imx51-zii-rdu1: limit usbh1 to full-speed
ARM: dts: imx6/7: Remove unit-address from anatop regulators
ARM: dts: imx: Switch NXP boards to SPDX identifier
ARM: dts: imx6qdl-phytec-pfla02: Use IRQ_TYPE specifier
ARM: dts: imx53-voipac-dmm-668: Use IRQ_TYPE specifier
ARM: dts: imx53-qsb: Use IRQ_TYPE specifier
ARM: dts: vf-colibri-eval-v3: Use IRQ_TYPE specifier
ARM: dts: imx6q-gk802: Do not hardcode input codes
ARM: dts: imx53-smd: Do not hardcode input codes
ARM: dts: imx53-ard: Do not hardcode input codes
ARM: dts: imx7: Fix error in coresight TPIU graph connection
ARM: dts: imx53: Fix LDB OF graph warning
ARM: dts: imx: fix IPU OF graph endpoint node names
ARM: dts: imx: Switch to SPDX identifier
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 12:21:51 +0000 (05:21 -0700)]
Merge tag 'uniphier-dt64-v4.18' of git://git./linux/kernel/git/masahiroy/linux-uniphier into next/dt
UniPhier ARM64 SoC DT updates for v4.18
- add more properties to ethernet nodes
* tag 'uniphier-dt64-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: add syscon-phy-mode property to each ethernet node
arm64: dts: uniphier: add clock-names and reset-names to ethernet node
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 12:20:31 +0000 (05:20 -0700)]
Merge tag 'uniphier-dt-v4.18' of git://git./linux/kernel/git/masahiroy/linux-uniphier into next/dt
UniPhier ARM SoC DT updates for v4.18
- add more properties to ethernet nodes
* tag 'uniphier-dt-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: add syscon-phy-mode property to each ethernet node
ARM: dts: uniphier: add required clocks and resets to Pro4 ethernet node
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 12:19:41 +0000 (05:19 -0700)]
Merge tag 'mvebu-dt64-4.18-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt64 for 4.18 (part 1)
- Allow using Armada 3700 gpio controller as interrupt one too
- Describe SPI flash on the EspressoBin
- Mark ahci as dma-coherent for Armada 7K/8K
- Add 10G interface support Armada 7K/8K based boards (including MacBin)
* tag 'mvebu-dt64-4.18-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: armada-37xx: mark the gpio controllers as irq controller
arm64: dts: marvell: 7040-db: describe the 10G interface as fixed-link
arm64: dts: marvell: 8040-db: describe the 10G interfaces as fixed-link
arm64: dts: marvell: mcbin: enable the fourth network interface
arm64: dts: marvell: mcbin: add 10G SFP support
arm64: dts: marvell: mark CP110 ahci as dma-coherent
arm64: dts: armada-3720-espressobin: wire up spi flash
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 12:17:47 +0000 (05:17 -0700)]
Merge tag 'mvebu-dt-4.18-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.18 (part 1)
- Update 32-bit Marvell EBU NAND DT nodes with new bindings
- Add NAND pinctrl information for the Armada 98DX3236 and variants
* tag 'mvebu-dt-4.18-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-xp-98dx: Add NAND pinctrl information
ARM: dts: armada-39x: update NAND node with new bindings
ARM: dts: armada-38x: update NAND node with new bindings
ARM: dts: armada-375: update NAND node with new bindings
ARM: dts: armada-370-xp: update NAND node with new bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 12:15:34 +0000 (05:15 -0700)]
Merge tag 'tegra-for-4.18-arm-dt' of git://git./linux/kernel/git/tegra/linux into next/dt
ARM: tegra: Device tree changes for v4.18-rc1
Contains a fix for the high-speed UART on Toradex Apalis TK1 boards as
well as IOMMU enablement for various devices on Tegra30 and Tegra30.
* tag 'tegra-for-4.18-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: dts: tegra114: Add IOMMU nodes to Host1x and its clients
ARM: dts: tegra30: Add IOMMU nodes to Host1x and its clients
ARM: tegra: apalis-tk1: Fix high speed UART compatible
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 12:07:55 +0000 (05:07 -0700)]
Merge tag 'tegra-for-4.18-dt-bindings' of git://git./linux/kernel/git/tegra/linux into next/dt
dt-bindings: tegra: Changes for v4.18-rc1
This contains the device tree bindings updates for the memory controller
hot resets that are implemented by driver patches in a different branch.
* tag 'tegra-for-4.18-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: Relocate Tegra20 memory controller bindings
dt-bindings: arm: tegra: Document #reset-cells property of the Tegra20 MC
dt-bindings: memory: tegra: Document #reset-cells property of the Tegra30 MC
dt-bindings: arm: tegra: Remove duplicated Tegra30+ MC binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 11:58:55 +0000 (04:58 -0700)]
Merge tag 'davinci-for-v4.18/dt' of git://git./linux/kernel/git/nsekhar/linux-davinci into next/dt
DaVinci device-tree updates for v4.18
* DA850 EVM gains USB support, SD card write-protect, card detect
and some clean-up
* Support for gpio-ranges makes using gpios from DT much easier
* Lego EV3 clean-up
* tag 'davinci-for-v4.18/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-evm: add WP and CD to MMC
ARM: dts: da850-lego-ev3: remove unnecessary gpio-keys properties
ARM: dts: da850-evm: use phandles to extend nodes
ARM: dts: da850: use gpio-ranges
ARM: dts: da850-evm: Enable usb_phy, usb0 and usb1
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 11:50:57 +0000 (04:50 -0700)]
Merge tag 'amlogic-dt64' of https://git./linux/kernel/git/khilman/linux-amlogic into next/dt
Amlogic 64-bit DT updates for v4.18
- AXG family: support more peripherals (wifi, eMMC, clocks)
- GX family: add/enable USB host support
* tag 'amlogic-dt64' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
dt-bindings: arm: amlogic: add support for the Tronsmart MXIII Plus
dt-bindings: arm: amlogic: add support for the Meson8m2 SoC
ARM64: dts: meson-axg: enable AP6255 wifi module
ARM64: dts: meson: add MMC resets
ARM64: dts: meson-axg: add an 32K alt aoclk
ARM64: dts: meson-axg: add tdm pins
ARM64: dts: meson-axg: add GPIO interrupt controller support
ARM64: dts: meson-axg: enable the eMMC controller
ARM64: dts: meson-gx: fix gxl clock controller compatible
ARM64: dts: meson-axg: use hhi syscon for the clock controller
ARM64: dts: meson-gx: sysctrl is the parent of the clock controller
dt-bindings: clock: meson: update documentation with hhi syscon
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 11:47:45 +0000 (04:47 -0700)]
Merge tag 'amlogic-dt' of https://git./linux/kernel/git/khilman/linux-amlogic into next/dt
Amlogic 32-bit DT updates for v4.18
- add support for meson8m2 SoC
- new board: Tronsmart MXIII Plus using meson8m2 SoC
- odroid-c1: add IR
* tag 'amlogic-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson8m2: add support for the Tronsmart MXIII Plus
ARM: dts: meson8: add the uart_A pins
ARM: dts: meson: add support for the Meson8m2 SoC
ARM: meson: add support for the Meson8m2 SoCs
ARM: dts: meson8b: odroid-c1: enable the IR receiver
ARM: dts: meson8b: odroid-c1: sort nodes alphabetically
ARM: dts: meson8b: add the cortex-a5-pmu compatible PMU
ARM: dts: meson8: add the cortex-a9-pmu compatible PMU
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 25 May 2018 11:47:13 +0000 (04:47 -0700)]
Merge tag 'hisi-arm64-dt-for-4.18v2' of git://github.com/hisilicon/linux-hisi into next/dt
ARM64: DT: Hisilicon SoC DT updates for 4.18v2
- Add mailbox, stub clock, CPU frequency scaling, thermal cooling
management and pcie msi interruption support for hi3660
- Add LPC support for hip06 and hip07
- Add PCIe, usb and emmc support for hi3798cv200
* tag 'hisi-arm64-dt-for-4.18v2' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hi3798cv200: enable emmc support for poplar board
arm64: dts: hi3798cv200: enable usb2 support for poplar board
arm64: dts: hi3798cv200: enable PCIe support for poplar board
arm64: dts: hisi: Enable Hisi LPC node for hip07
arm64: dts: hisi: Enable Hisi LPC node for hip06
arm64: dts: hi3660: Add pcie msi interrupt attribute
arm64: dts: hi3660: Add thermal cooling management
arm64: dts: hi3660: Add CPU frequency scaling support
arm64: dts: hi3660: Add stub clock node
arm64: dts: hi3660: Add mailbox node
Signed-off-by: Olof Johansson <olof@lixom.net>
Bjorn Andersson [Fri, 18 May 2018 06:26:38 +0000 (23:26 -0700)]
arm64: dts: qcom: msm8996: Add ufs related nodes
Add the UFS QMP phy node and the UFS host controller node, now that we
have working UFS and the necessary clocks in place.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Thierry Escande [Fri, 27 Apr 2018 06:10:28 +0000 (08:10 +0200)]
arm64: dts: msm8996: fix gic_irq_domain_translate warnings
Remove the usage of IRQ_TYPE_NONE to fix loud warnings from
patch (
83a86fbb5b56b "irqchip/gic: Loudly complain about
the use of IRQ_TYPE_NONE").
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Douglas Anderson [Tue, 15 May 2018 03:59:22 +0000 (20:59 -0700)]
arm64: dts: qcom: sdm845: Sort nodes in the soc by address
This is pure-churn and should be a no-op. I'm doing it in the hopes
of reducing merge conflicts. When things are sorted in a sane way
(and by base address seems sane) then it's less likely that future
patches will cause merge conflicts.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Douglas Anderson [Tue, 15 May 2018 04:43:06 +0000 (21:43 -0700)]
arm64: dts: qcom: sdm845: Sort nodes in the reserved mem by address
Let's keep the reserved-memory node tidy and neat and keep it sorted
by address. This should have no functional change.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Douglas Anderson [Wed, 9 May 2018 21:34:39 +0000 (14:34 -0700)]
arm64: dts: sdm845: Add command DB node
Add command DB node based on the bindings example.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Douglas Anderson [Wed, 9 May 2018 20:05:28 +0000 (13:05 -0700)]
arm64: dts: sdm845: Fix xo_board clock name and speed
The RPMh clock driver assumes that the xo_board clock is named
"xo_board", not "xo-board". Add a "clock-output-names" property to
the device tree to get the right name.
Also add the proper speed for the xo-clock as
38400000. This is
internally divided in RPMh clock driver to get "bi_tcxo" at
19200000.
After this change the clock tree in /sys/kernel/debug/clk/clk_summary
looks much better.
NOTES:
- Technically you could argue that this clock could belong in board
.dts files, not in the SoC one. However at the moment it's believed
that 100% of sdm845 boards will have an external clock at 38.4. It
can always be moved later if necessary.
- We could rename the "xo-board" device tree node to "xo_board" to
achieve the same effect as this patch. Presumably device-tree folks
would rather keep node names using dashes though.
- We could change the RPMh clock driver to use a dash to achieve the
same effect as this patch, but all other clocks in the clock tree
use underscores. It seems silly to change just this one.
Fixes:
7bafa643647f ("arm64: dts: sdm845: Add minimal dts/dtsi files for sdm845 SoC and MTP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Sibi S [Mon, 30 Apr 2018 14:44:28 +0000 (20:14 +0530)]
arm64: dts: qcom: Add SDM845 SMEM nodes
Add all the necessary dt nodes to support SMEM driver
on SDM845. It also adds the required memory carveouts
so that the kernel does not access memory that is in
use.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Sibi S [Wed, 25 Apr 2018 14:38:03 +0000 (20:08 +0530)]
arm64: dts: qcom: Add APSS shared mailbox node to SDM845
This patch add the node to support APSS shared
mailbox on SDM845
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Srinivas Kandagatla [Wed, 18 Apr 2018 16:34:15 +0000 (17:34 +0100)]
arm64: dts: msm8916: fix gic_irq_domain_translate warnings
Remove the usage of IRQ_TYPE_NONE to fix loud warnings from
patch (
83a86fbb5b56b "irqchip/gic: Loudly complain about
the use of IRQ_TYPE_NONE").
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Thierry Escande <thierry.escande@linaro.org>
Tested-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Mahesh Sivasubramanian [Tue, 10 Apr 2018 17:57:24 +0000 (11:57 -0600)]
dt-bindings: introduce Command DB for QCOM SoCs
Command DB provides information on shared resources like clocks,
regulators etc., probed at boot by the remote subsytem and made
available in shared memory.
Cc: devicetree@vger.kernel.org
Signed-off-by: Mahesh Sivasubramanian <msivasub@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Srinivas Kandagatla [Tue, 10 Apr 2018 13:54:26 +0000 (14:54 +0100)]
arm64: dts: apq8096-db820c: Add micro sd card supplies
This patch adds missing microSD card supplies, without this uSD
card will not be detected.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Karthikeyan Ramasubramanian [Fri, 30 Mar 2018 17:08:16 +0000 (11:08 -0600)]
dt-bindings: soc: qcom: Add device tree binding for GENI SE
Add device tree binding support for the QCOM GENI SE driver.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Thierry Escande [Thu, 29 Mar 2018 19:15:23 +0000 (21:15 +0200)]
dt-bindings: net: bluetooth: Add qualcomm-bluetooth
Add binding document for serial bluetooth chips using Qualcomm protocol.
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Thierry Escande [Thu, 29 Mar 2018 19:15:22 +0000 (21:15 +0200)]
arm64: dts: apq8096-db820c: enable bluetooth node
Add a new serial node for the Qualcomm BT controller QCA6174. This
allows automatic probing and hci registration through the serdev
framework instead of relying on the userspace helpers.
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Srinivas Kandagatla [Thu, 29 Mar 2018 19:15:21 +0000 (21:15 +0200)]
arm64: dts: apq8096-db820c: Enable wlan and bt en pins
This patch enables regulators and gpios for the Qualcomm QCA6174 BT/WLAN
combo controller.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Arnd Bergmann [Tue, 13 Mar 2018 12:13:09 +0000 (13:13 +0100)]
arm64: dts: qcom: rename qcom,pcie devices to pcie
The node name for a PCIe host bridge must be "pcie" as required by
the binging. dtc now warns about it:
arch/arm64/boot/dts/qcom/apq8096-db820c.dtb: Warning (pci_bridge): /soc/agnoc@0/qcom,pcie@610000: node name is not "pci" or "pcie"
arch/arm64/boot/dts/qcom/apq8096-db820c.dtb: Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'
arch/arm64/boot/dts/qcom/msm8996-mtp.dtb: Warning (pci_bridge): /soc/agnoc@0/qcom,pcie@610000: node name is not "pci" or "pcie"
arch/arm64/boot/dts/qcom/msm8996-mtp.dtb: Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'
This renames the nodes as appropriate.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Jeremy McNicoll [Mon, 12 Mar 2018 08:36:57 +0000 (01:36 -0700)]
arm64: dts: msm8992: add pstore-ramoops support
With the addition of this ramoops node it enables post mortem
analysis if a debug cable is not attached and/or not available.
All addresses and values were extracted from CAF AOSP marshmallow
DR 1.6.
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Rajendra Nayak [Mon, 12 Mar 2018 14:12:24 +0000 (19:42 +0530)]
arm64: dts: sdm845: Add minimal dts/dtsi files for sdm845 SoC and MTP
Add a skeletal sdm845 SoC dtsi and MTP board dts/dtsi files
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Jeremy McNicoll [Fri, 27 Jan 2017 09:10:04 +0000 (01:10 -0800)]
arm64: dts: Enable onboard SDHCI on msm8992
This enables SDHCI on the Nexus 5X as well creates common smd_rpm node
which can be shared between both 5X and 6P as per HW design.
Given the lack of documentation, only downstream code was used as a reference
and it eludes to the fact that 8994-rpm-regulator is common between both msm8992
& msm8994. [ see msm.git branch: msm-angler-3.10-marshmallow-mr1, msm8992.dtsi]
At this early stage of development it makes sense for the 8994-rpm-regulator
to be common until data / documentation suggests otherwise.
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Stefan Mavrodiev [Wed, 16 May 2018 11:38:08 +0000 (14:38 +0300)]
ARM: dts: sun7i: Add Olimex A20-SOM-EVB-eMMC board
With the new rev.E of A20-SOM-EVB, there is option for 16GB eMMC.
Currently used card is KLMAG2GEND, wired to MMC2 slot.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Daniel Mack [Thu, 17 May 2018 09:05:52 +0000 (11:05 +0200)]
ARM: dts: imx28/imx53: enable edt-ft5x06 wakeup source
The touchscreen driver no longer configures the device as wakeup source by
default. A "wakeup-source" property is needed.
To avoid regressions, this patch changes the DTS files for the only two
users of this driver that didn't have this property yet.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Nikita Yushchenko [Wed, 16 May 2018 06:53:49 +0000 (09:53 +0300)]
ARM: dts: imx51-zii-rdu1: cleanup eMMC node
On RDU1, sdhc1 is used for eMMC, and that is 3.3V only.
Thus configure device node not to probe it as SD/SDIO and not try 1.8V.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Nikita Yushchenko [Wed, 16 May 2018 06:39:21 +0000 (09:39 +0300)]
ARM: dts: vf610-zii-dev: enable vf610 builtin temp sensor
Vybrid has single internal temperature sensor connected to both internal
ADC modules.
vf610-zii-dev already has ADC0 enabled. Now, to get temperature sensor
captured by iio_hwmon driver, need to configure iio_hwmon node to use
that ADC.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Wed, 16 May 2018 04:48:17 +0000 (12:48 +0800)]
ARM: dts: imx7d: use operating-points-v2 for cpu
This patch uses "operating-points-v2" instead of
"operating-points" to be more fit with cpufreq-dt
driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Tue, 15 May 2018 09:18:15 +0000 (17:18 +0800)]
ARM: dts: imx7s-warp: remove unnecessary cpu regulator supply
i.MX7S does NOT support CPU frequency scaling, so no
need to specify the CPU regulator supply.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Wed, 16 May 2018 02:25:48 +0000 (10:25 +0800)]
ARM: dts: imx7d: correct cpu supply name for voltage scaling
Correct CPU supply name to meet cpufreq-dt driver's
requirement for voltage scaling.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Nikita Yushchenko [Tue, 15 May 2018 08:45:02 +0000 (11:45 +0300)]
ARM: dts: imx51-zii-rdu1: limit usbh1 to full-speed
On RDU1, imx51 usbh1 interface is either not used, or used via external
block that breaks USB2 signalling.
To keep things working if high-speed device gets connected to that
block, use ChipIdea feature to limit port to full speed.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Mon, 14 May 2018 13:31:54 +0000 (10:31 -0300)]
ARM: dts: imx6/7: Remove unit-address from anatop regulators
Remove unit-address and reg property from anatop regulators to fix
the following DTC warnings with W=1:
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unique_unit_address): /soc/aips-bus@
2000000/anatop@
20c8000/regulator-vddcore@
20c8140: duplicate unit-address (also used in node /soc/aips-bus@
2000000/anatop@
20c8000/regulator-vddpu@
20c8140)
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unique_unit_address): /soc/aips-bus@
2000000/anatop@
20c8000/regulator-vddcore@
20c8140: duplicate unit-address (also used in node /soc/aips-bus@
2000000/anatop@
20c8000/regulator-vddsoc@
20c8140)
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unique_unit_address): /soc/aips-bus@
2000000/anatop@
20c8000/regulator-vddpu@
20c8140: duplicate unit-address (also used in node /soc/aips-bus@
2000000/anatop@
20c8000/regulator-vddsoc@
20c8140)
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Sun, 6 May 2018 13:00:49 +0000 (08:00 -0500)]
ARM: dts: am3517-evm: Add User LEDs and Pushbutton
There are some LED's attached to the GPIO expander, and
there are is a bank of switches attached to the GPIO expander.
This patch associates the LED and the switches to it.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adam Ford [Sun, 6 May 2018 13:00:48 +0000 (08:00 -0500)]
ARM: dts: am3517-evm: Add I/O expander for User DIP switches and LEDS
There is a tca6416 GPIO expander on i2c2. This patch enables the
GPIO expander which has several LED's and some connected DIP
switches
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Chris Packham [Fri, 4 May 2018 03:06:38 +0000 (15:06 +1200)]
ARM: dts: armada-xp-98dx: Add NAND pinctrl information
Add pin control information for the NAND interface on the Armada
98DX3236 and variants.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Miquel Raynal [Wed, 25 Apr 2018 14:48:02 +0000 (16:48 +0200)]
ARM: dts: armada-39x: update NAND node with new bindings
Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Miquel Raynal [Wed, 25 Apr 2018 14:48:01 +0000 (16:48 +0200)]
ARM: dts: armada-38x: update NAND node with new bindings
Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Miquel Raynal [Wed, 25 Apr 2018 14:48:00 +0000 (16:48 +0200)]
ARM: dts: armada-375: update NAND node with new bindings
Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Miquel Raynal [Wed, 25 Apr 2018 14:47:59 +0000 (16:47 +0200)]
ARM: dts: armada-370-xp: update NAND node with new bindings
Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Uwe Kleine-König [Wed, 21 Mar 2018 10:50:03 +0000 (11:50 +0100)]
arm64: dts: marvell: armada-37xx: mark the gpio controllers as irq controller
This allows to reference these gpio controller as interrupt parent. Also
add a comment which cpu line names are managed by the controllers
because "nb" and "sb" usually doesn't appear in schematics, but MPPX_Y
do.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Antoine Tenart [Thu, 17 May 2018 08:29:39 +0000 (10:29 +0200)]
arm64: dts: marvell: 7040-db: describe the 10G interface as fixed-link
This patch adds a fixed-link node to the 10G interface of the 7040-db
board. This is required as the mvpp2 driver now uses phylink. The best
solution would have been to describe the SFP cage but they are not
wired correctly, and thus unusable, so we chose to use fixed-link
instead.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Antoine Tenart [Thu, 17 May 2018 08:29:38 +0000 (10:29 +0200)]
arm64: dts: marvell: 8040-db: describe the 10G interfaces as fixed-link
This patch adds a fixed-link node to both 10G interfaces of the 8040-db
board. This is required as the mvpp2 driver now uses phylink. The best
solution would have been to describe the SFP cages but they are not
wired correctly, and thus unusable, so we chose to use fixed-link
instead.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Antoine Tenart [Thu, 17 May 2018 08:29:37 +0000 (10:29 +0200)]
arm64: dts: marvell: mcbin: enable the fourth network interface
This patch enables the fourth network interface on the Marvell
Macchiatobin. It is configured in the 2500Base-X PHY mode. The SFP cage
is also described.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Russell King [Thu, 17 May 2018 08:29:36 +0000 (10:29 +0200)]
arm64: dts: marvell: mcbin: add 10G SFP support
This patch adds the SFP cage description in the Marvell Armada 8040
mcbin, for both 10G interfaces.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[Antoine: small reworks, commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Chen-Yu Tsai [Tue, 1 May 2018 16:12:25 +0000 (00:12 +0800)]
ARM: dts: sun8i: r40: bananapi-m2-ultra: Enable GMAC ethernet controller
The Bananapi M2 Ultra has a Realtek RTL8211E RGMII PHY tied to the GMAC.
The PMIC's DC1SW output provides power for the PHY, while the ALDO2
output provides I/O voltages on both sides.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Chen-Yu Tsai [Tue, 1 May 2018 16:12:24 +0000 (00:12 +0800)]
ARM: dts: sun8i: r40: Add device node and RGMII pinmux node for GMAC
The R40 SoC has a GMAC (gigabit capable Ethernet controller). Add a
device node for it. The only publicly available board for this SoC
uses an RGMII PHY. Add a pinmux node for it as well.
Since this SoC also has an old 10/100 Mbps EMAC, which also has an
MDIO bus controller, the MDIO bus for the GMAC is labeled "gmac_mdio".
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Chen-Yu Tsai [Tue, 1 May 2018 16:12:23 +0000 (00:12 +0800)]
ARM: dts: sun8i: r40: bananapi-m2-ultra: Sort device node dereferences
The device nodes dereference (&foo) usages should be sorted by the label
names, barring any parsing order issues such as the #include statement
for the PMIC's .dtsi file that must come after the PMIC.
Move the mmc and ohci blocks in front of the PMIC's regulator blocks.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Adam Ford [Sat, 12 May 2018 12:23:58 +0000 (07:23 -0500)]
ARM: dts: da850-evm: add WP and CD to MMC
The legacy mode uses the write protect and card detect but DT does not.
This patch enables Write-Protect and Card-Detect pins for the MMC card, and
the gpio-ranges property sets the gpio pinmuxing for those respective pins.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Olof Johansson [Tue, 15 May 2018 20:52:13 +0000 (13:52 -0700)]
Merge tag 'v4.18-rockchip-dts64-1' of git://git./linux/kernel/git/mmind/linux-rockchip into next/dt
All iommus got their clocks added and rk3399 got support for its
usb3-phy otg-port and better ajustment for the cpll child clocks.
On the board side, all rk3399 got their typec phys enabled - which
is needed for better usb support, the sapphire board got some more
properties moved to the excavator baseboard where they really belong,
kevin got a fix to use a real devicetree compatible and puma-haikou
got its hdmi port enabled.
* tag 'v4.18-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: enable hdmi on rk3399-puma-haikou
arm64: dts: rockchip: use canonical compatible for touchpad/touchscreen on gru-kevin
arm64: dts: rockchip: add clocks in iommu nodes
arm64: dts: rockchip: add usb3-phy otg-port support for rk3399
arm64: dts: rockchip: remove PCIe assigned-clocks in excavator baseboard
arm64: dts: rockchip: move rk3399-sapphire PCIe to excavator baseboard
arm64: dts: rockchip: assign clock rate for cpll child clocks on rk3399
arm64: dts: rockchip: enable typec-phy0 for rk3399-puma-haikou
arm64: dts: rockchip: enable typec-phy1 for rk3399-puma
arm64: dts: rockchip: enable typec-phy for rk3399-firefly
arm64: dts: rockchip: enable typec-phy for rk3399-sapphire
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 15 May 2018 20:51:43 +0000 (13:51 -0700)]
Merge tag 'v4.18-rockchip-dts32-1' of git://git./linux/kernel/git/mmind/linux-rockchip into next/dt
Fixed pin numbers for uart4 on rk3288, iommu clocks and small changes
over multiple boards like default serial setting for rk3288-tinker,
output selection for the dp83867 on the phycore-som and the newly
added pwm-backlight delay properties for veyron boards.
* tag 'v4.18-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: default serial for rk3288 Tinker Board
ARM: dts: rockchip: set PWM delay backlight settings for Minnie
ARM: dts: rockchip: set PWM delay backlight settings for Veyron
ARM: dts: rockchip: add clocks in iommu nodes
ARM: dts: rockchip: Add dp83867 CLK_OUT muxing on rk3288-phycore-som
ARM: dts: rockchip: fix uart4 pin-numbers for rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 15 May 2018 20:48:01 +0000 (13:48 -0700)]
Merge tag 'juno-updates-4.18' of git://git./linux/kernel/git/sudeep.holla/linux into next/dt
ARMv8 Juno/Vexpress updates/cleanups for v4.18
1. Add the missing connections to the STM output port as all endpoint
connections must be bidirectional.
2. Replace all the custom OF graph endpoint node names with the standard
'endpoint'
3. Cleanup to replace all underscores('_') with hyphens('-') in the
device node names
4. Syntactic restructuring of motherboard include file so that it can be
included at the top of any other DTS file as it should be rather than
existing include in the middle of the file at a specific location
* tag 'juno-updates-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno/rtsm: re-structure motherboard includes
arm64: dts: juno: replace '_' with '-' in node names
arm64: dts: juno: Fix "debounce-interval" property misspelling
arm64: dts: juno: fix OF graph endpoint node names
arm64: dts: juno: fix missing Coresight STM graph connection
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 15 May 2018 20:46:21 +0000 (13:46 -0700)]
Merge tag 'vexpress-updates-4.18' of git://git./linux/kernel/git/sudeep.holla/linux into next/dt
ARMv7 Vexpress updates/cleanups for v4.18
1. Syntactic restructuring of motherboard include file so that it can be
included at the top of any other DTS file as it should be rather than
existing include in the middle of the file at a specific location
2. Use of standard GPIO controller bindings for few sysreg components
like LED, MMC Write Protect/Card Detect and Flash Write Protect
to fix some of the new DTC warnings
3. Cleanup to replace all underscores('_') with hyphens('-') in the
device node names
* tag 'vexpress-updates-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: replace '_' with '-' in node names
ARM: dts: vexpress: use standard gpio bindings for sys_{led,mci,flash}
ARM: dts: vexpress: Restructure motherboard includes
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 15 May 2018 20:44:07 +0000 (13:44 -0700)]
Merge tag 'sti-dt-for-v4.18-round1' of git://git./linux/kernel/git/pchotard/sti into next/dt
STi DT update:
_ Fix complain about IRQ_TYPE_NONE_usage
* tag 'sti-dt-for-v4.18-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: stihxxx-b2120: Fix complain about IRQ_TYPE_NONE usage
ARM: dts: stih410: Fix complain about IRQ_TYPE_NONE usage
ARM: dts: stih407: Fix complain about IRQ_TYPE_NONE usage
ARM: dts: stih407-pinctrl: Fix complain about IRQ_TYPE_NONE usage
ARM: dts: stih407-family: Fix complain about IRQ_TYPE_NONE usage
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 15 May 2018 20:39:40 +0000 (13:39 -0700)]
Merge tag 'v4.17-next-dts64' of https://git./linux/kernel/git/matthias.bgg/linux into next/dt
- add clock and pinctrl nodes for mt2712e
- add High-Speed DMA and audio nodes for mt7622
* tag 'v4.17-next-dts64' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: dts: mt7622: add audio related device nodes
arm64: dts: mt7622: add High-Speed DMA device nodes
arm64: dts: mt2712: add pintcrl device node.
arm64: dts: mt2712: add pintcrl file
arm64: dts: add clock device nodes of MT2712
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 15 May 2018 20:39:06 +0000 (13:39 -0700)]
Merge tag 'v4.17-next-dts32' of https://git./linux/kernel/git/matthias.bgg/linux into next/dt
convert to SPDX IDs
mt7623:
- add audio, bluetooth, highspees DMA and SPI-NOR nodes
- fix invalid memory nodes by not using skeleton64.dtsi
- fix memory size for bananapi-r2
- fix dtc warnings
- refactor dts and dtsi to aviod code duplication
- add mt7623n and mt7623a reference boards
* tag 'v4.17-next-dts32' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm: dts: mt7623: add MT7623N reference board with eMMC
arm: dts: mt7623: add MT7623A reference boards
arm: dts: mt7623: add MT7623A SoC level DTS
arm: dts: mt7623: extend common file reused by all boards with MT7623 SoCs
arm: dts: mt6323: move node mt6323 leds to mt6323.dtsi
arm: dts: mt7623: add BTIF, HSDMA and SPI-NOR device nodes
arm: dts: mt7623: fix all Warnings (unit_address_vs_reg)
arm: dts: mt7623: fix available memory size on bananapi-r2
arm: dts: mt7623: fix invalid memory node being generated
arm: dts: mediatek: converted to using SPDX identifiers
arm: dts: mediatek: modify audio related nodes for both MT2701 and MT7623
Signed-off-by: Olof Johansson <olof@lixom.net>
Adam Ford [Mon, 7 May 2018 00:56:29 +0000 (19:56 -0500)]
ARM: dts: logicpd-som-lv: Fix Touchscreen controller
The touchscreen patch did not apply to this branch correctly and
inadvertently got placed onto I2C2 when it should be on I2C3. This fixes
the issue.
Fixes:
121685b14624 ("ARM: dts: logicpd-som-lv: Enable Touchscreen
controller")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adam Ford [Sun, 6 May 2018 13:00:47 +0000 (08:00 -0500)]
ARM: dts: am3517-som: Add Seiko Instruments RTC s35390a
The SOM used in the am3517-evm has a s35390a onboard. This
patch allows the s35390a to be used as the RTC.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eyal Reizer [Sun, 6 May 2018 07:58:06 +0000 (10:58 +0300)]
ARM: dts: am437x-sk-evm: add wilink8 support
enable mmc3 used for wlan and uart1 used for bluetooth
configure the gpios used for wlan and bluetooth controls
add fixed voltage regulator used for wlan power control
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adam Ford [Sun, 6 May 2018 01:26:11 +0000 (20:26 -0500)]
ARM: dts: am3517-evm: Add LCD panel type 15 support
The AM3517-EVM by Logic PD has a Logic PD type 15 display LCD
attached to the baseboard, and the SOM itself has an integrated
touchscreen controller. This patch enables both the LCD and
the tsc2004 on the SOM.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adam Ford [Sun, 6 May 2018 01:26:10 +0000 (20:26 -0500)]
ARM: dts: am3517-som: Associate cpu to regulator supply
The am3517-som is powered by vdd_core_reg, so let's add the
'cpu' device-tree node with the 'vdd_core' regulator as the core
supply.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adam Ford [Sun, 6 May 2018 01:26:09 +0000 (20:26 -0500)]
ARM: dts: am3517-som: Add TI TPS65023 regulators
This commit adds the common voltage regulators used on LogicPD's
AM3517 System-On-Modules.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adam Ford [Sun, 6 May 2018 01:26:08 +0000 (20:26 -0500)]
ARM: dts: am3517-evm: Split off SOM features from baseboard
The am3517-evm consists of an am3517 SOM-M2 and a baseboard.
As items are added that are unique to the baseboard, let's place
them in a file called am3517-som.dtsi. These items will be
common for all variants of the SOM.
Anything unique to the baseboard will be placed into
am3517-evm.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adam Ford [Sun, 6 May 2018 01:26:07 +0000 (20:26 -0500)]
ARM: dts: am3517: Add pinmuxing, CD and WP for MMC1
The boardboard supports card detect and write protect, so let's
enable those pins.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adam Ford [Fri, 4 May 2018 21:00:11 +0000 (16:00 -0500)]
ARM: dts: logicpd-som-lv: Add fixed 26MHz clock as fck for twl
The board uses 26MHz oscillator for the twl4030 HFCLK. This way we will
not depend on the bootloader to configure the CFG_BOOT:HFCLK_FREQ
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adam Ford [Fri, 4 May 2018 21:00:10 +0000 (16:00 -0500)]
ARM: dts: logicpd-torpedo: Add fixed 26MHz clock as fck for twl
The board uses 26MHz oscillator for the twl4030 HFCLK.
This way we will not depend on the bootloader to configure the
CFG_BOOT:HFCLK_FREQ
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hernán Gonzalez [Sun, 13 May 2018 23:29:52 +0000 (20:29 -0300)]
ARM: dts: omap3-pandora-common: Use IRQ_TYPE specifier
Replace magic number with the proper IRQ_TYPE specifier to improve DT
readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hernán Gonzalez [Sun, 13 May 2018 23:19:56 +0000 (20:19 -0300)]
ARM: dts: am335x-boneblue: Use IRQ_TYPE specifier
GPIO_ACTIVE_LOW was being used to specify an interrupt, use
IRQ_TYPE_EDGE_RISING instead. This improves DT readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hernán Gonzalez [Sun, 13 May 2018 23:19:03 +0000 (20:19 -0300)]
ARM: dts: am335x-baltos.dtsi: Use IRQ_TYPE specifier
GPIO_ACTIVE_LOW was being used to specify an interrupt, use
IRQ_TYPE_EDGE_RISING instead. This improves DT readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hernán Gonzalez [Sun, 13 May 2018 23:18:14 +0000 (20:18 -0300)]
ARM: dts: am335x-baltos-ir5221: Use IRQ_TYPE specifier
GPIO_ACTIVE_LOW was being used to specify an interrupt, use
IRQ_TYPE_EDGE_RISING instead. This improves DT readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hernán Gonzalez [Sun, 13 May 2018 23:16:33 +0000 (20:16 -0300)]
ARM: dts: am335x-baltos-ir3220: Use IRQ_TYPE specifier
GPIO_ACTIVE_LOW was being used to specify an interrupt, use
IRQ_TYPE_EDGE_RISING instead. This improves DT readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Tue, 8 May 2018 13:20:53 +0000 (16:20 +0300)]
Revert "ARM: dts: am437x-sk-evm: Correct tps65218 irq type"
This reverts commit
561f9bcf268422ebe78a1739d86a255fd481c71c.
While the correct IRQ level fixed the WARN_ON(), but prevented the probe
of tps65218 as GIC_SPI does not support LEVEL_LOW (?)
Use LEVEL_HIGH as it looks to be the accurate one since the INTn of TPS is
connected to NMIn of the SoC.
Fixes:
561f9bcf2684 ("ARM: dts: am437x-sk-evm: Correct tps65218 irq type")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Tue, 8 May 2018 13:20:52 +0000 (16:20 +0300)]
ARM: dts: am437x-epos-evm: Fixup (again) tps65218 irq type
While the correct IRQ level fixed the WARN_ON(), but prevented the probe
of tps65218 as GIC_SPI does not support LEVEL_LOW (?)
Use LEVEL_HIGH as it looks to be the accurate one since the INTn of TPS is
connected to NMIn of the SoC.
Fixes:
7a53a34622da ("ARM: dts: am437x-epos-evm: Correct tps65218 irq type")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Tue, 8 May 2018 13:20:51 +0000 (16:20 +0300)]
ARM: dts: am437x-cm-t43: Fixup (again) tps65218 irq type
While the correct IRQ level fixed the WARN_ON(), but prevented the probe
of tps65218 as GIC_SPI does not support LEVEL_LOW (?)
Use LEVEL_HIGH as it looks to be the accurate one since the INTn of TPS is
connected to NMIn of the SoC.
Fixes:
b997f534b551 ("ARM: dts: am437x-cm-t43: Correct tps65218 irq type")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Tue, 8 May 2018 13:20:50 +0000 (16:20 +0300)]
ARM: dts: am437x-gp-evm: Fixup (again) tps65218 irq type
While the correct IRQ level fixed the WARN_ON(), but prevented the probe
of tps65218 as GIC_SPI does not support LEVEL_LOW (?)
Use LEVEL_HIGH as it looks to be the accurate one since the INTn of TPS is
connected to NMIn of the SoC.
Fixes:
5692b911c980 ("ARM: dts: am437x-gp-evm: Correct tps65218 irq type")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Tue, 8 May 2018 10:04:33 +0000 (13:04 +0300)]
ARM: dts: am335x-evmsk: Add phandle for the backlight for the panel
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Tue, 15 May 2018 18:13:24 +0000 (11:13 -0700)]
Merge branch 'omap-for-v4.18/dt-fixes' into omap-for-v4.18/dt
Rob Herring [Tue, 8 May 2018 13:59:30 +0000 (08:59 -0500)]
ARM: dts: omap: fix OMAP3 CM-T3x OF graph video connectors
The OMAP3 CM-T3x based boards define 2 /connector nodes for S-Video and
DVI output. However, since they have the same node name, the S-Video
connector overwritten. This leaves a dangling graph connection which
gives the following warning:
arch/arm/boot/dts/omap3-sbc-t3517.dtb: Warning (graph_endpoint):
/ocp@
68000000/dss@
48050000/encoder@
48050c00/port/endpoint: graph
connection to node '/connector/port/endpoint' is not bidirectional
Fix this by renaming the nodes to s-video-connector and dvi-connector.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rob Herring [Tue, 8 May 2018 13:59:29 +0000 (08:59 -0500)]
ARM: dts: omap: fix OF graph in omap3-devkit8000
omap3-devkit8000-common.dtsi defines a graph connection for DVI, but
then omap3-devkit8000-lcd-common.dtsi overrides that with a graph
connection for the LCD as the same output signals are used. This
leaves an incomplete graph as the TFP410 output has only half a
connection. The result is the following warning:
arch/arm/boot/dts/omap3-devkit8000-lcd70.dtb: Warning (graph_endpoint):
/encoder0/ports/port@0/endpoint: graph connection to node
'/ocp@
68000000/dss@
48050000/port/endpoint' is not bidirectional
Fix this by defining multiple endpoints which is the correct way to show
a 1 to many connection.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Shawn Guo [Fri, 11 May 2018 02:03:40 +0000 (10:03 +0800)]
arm64: dts: hi3798cv200: enable emmc support for poplar board
It adds pinctrl device pinconf@
8a21000, gpio-ranges for GPIO devices,
and then enables eMMC support for Hi3798CV200 Poplar board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Shawn Guo [Fri, 11 May 2018 02:03:39 +0000 (10:03 +0800)]
arm64: dts: hi3798cv200: enable usb2 support for poplar board
It adds usb2 phy devices, and enables ehci/ohci support for Hi3798CV200
Poplar board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Shawn Guo [Fri, 11 May 2018 02:03:38 +0000 (10:03 +0800)]
arm64: dts: hi3798cv200: enable PCIe support for poplar board
It adds combophy devices under peripheral controller and enables PCIe
support for Hi3798CV200 Poplar board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
John Garry [Mon, 30 Apr 2018 15:15:42 +0000 (23:15 +0800)]
arm64: dts: hisi: Enable Hisi LPC node for hip07
The patch enables the HiSi LPC node for hip07, with
the IPMI child device.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
John Garry [Mon, 30 Apr 2018 15:15:41 +0000 (23:15 +0800)]
arm64: dts: hisi: Enable Hisi LPC node for hip06
The patch enables the HiSi LPC node for hip06, with
IPMI and UART child devices.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Yao Chen [Fri, 11 May 2018 09:15:49 +0000 (17:15 +0800)]
arm64: dts: hi3660: Add pcie msi interrupt attribute
Add pcie msi interrupt attribute for hi3660 SOC.
Signed-off-by: Yao Chen <chenyao11@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Tao Wang [Tue, 15 May 2018 02:53:14 +0000 (10:53 +0800)]
arm64: dts: hi3660: Add thermal cooling management
Add nodes and properties for thermal cooling management support.
Signed-off-by: Tao Wang <jean.wangtao@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Leo Yan [Tue, 15 May 2018 02:53:13 +0000 (10:53 +0800)]
arm64: dts: hi3660: Add CPU frequency scaling support
Add two CPU OPP tables, one table is corresponding to one cluster,
which allow CPU frequency scaling on hi3660 platforms.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>