OSDN Git Service
Tomi Valkeinen [Fri, 30 Jul 2010 09:39:34 +0000 (12:39 +0300)]
OMAP: DSS2: DSI: add option to leave DSI lanes powered on
The DSI pins are powered by VDDS_DSI. If VDDS_DSI is off, the DSI pins
are floating even if they are pinmuxed to, say, safe mode and there's a
pull down/up.
This patch gives the panel drivers an option to leave the VDDS_DSI power
enabled while the DSS itself is turned off. This can be used to keep the
DSI lanes in a valid state while DSS is off, if the DSI pins are muxed
for pull down (not done in this patch).
There will be a slight power consumption increase (~100 uA?) when the
VDDS_DSI is left on, but because this option is used when the panel is
left on, the regulator consumption is negligible compared to panel power
consumption.
When the panel is fully turned off the VDDS_DSI is also turned off.
As an added bonus this will give us faster start up time when starting
up the DSS and the regulator is already enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Wed, 28 Jul 2010 12:53:38 +0000 (15:53 +0300)]
OMAP: DSS2: DSI: implement ULPS enter and exit
Entering ULPS (Ultra Low Power State) happens by sending ULPS entry
sequence to the DSI peripheral and pulling the DSI lines down.
Exiting ULPS happens by sending ULPS exit sequence.
We can send the ULPS entry sequence by using OMAP DSS HW's ULPS support,
but we cannot use the ULPS exit support from DSS HW. DSS HW refuses to
send the ULPS exit sequence if it thinks that the lanes are not in ULPS.
After being in OFF mode the DSS HW has been reset, and so it does not
know that the lanes are actually in ULPS.
Thus we need to use the lane override support and manually send the ULPS
exit sequence. Luckily the sequence is very simple.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Thu, 14 Apr 2011 08:42:22 +0000 (11:42 +0300)]
OMAP: DSS2: DSI: Remove CIO LDO status check
CIO LDO status check seems to be broken on OMAP3630+ chips, and it's
also quite unclear what LDO status actually tells and when its status
changes.
This patch removes the whole check on the grounds that if there's a
problem with the LDO, we should anyway catch the problem as we check the
CIO power state and CIO reset status.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Tue, 27 Jul 2010 08:11:48 +0000 (11:11 +0300)]
OMAP: DSS2: DSI: Add lane override functions
DSI_DSIPHY_CFG10 register can be used to override DSI lane state. Add
functions to configure and enable the override, and to disable the
override.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Archit Taneja [Mon, 18 Apr 2011 04:02:13 +0000 (09:32 +0530)]
OMAP2PLUS: DSS2: Clean up omap_display_init()
Currently, omap_display_init() maintains arrays for hwmod name(oh_name) and the
correspnding platform_device name(dev_name) needed by omap_device_build().
A variable oh_count keeps a track of the number of devices to build from oh_name
based on what omap revision it is.
Clean this up by maintaining an array of omap_dss_hwmod_data struct which is
defined for each omap revision as suggested by Tomi Valkeinen. Assign the
corresponding omap_dss_hwmod_data array struct to the pointer curr_dss_hwmod in
omap_display_init().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Mon, 4 Apr 2011 06:36:23 +0000 (09:36 +0300)]
OMAP: DSS2: improve clock debugfs output
OMAP4 has clocks set up in a bit interesting way, causing, for example,
the DSS's "ick" to be called "dss_fck".
This patch changes the debugfs output to show both the DSS's name for
the clock (ie. basically the clock alias), and the real name from the
clock struct.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Mon, 4 Apr 2011 12:40:23 +0000 (15:40 +0300)]
OMAP: DSS2: Convert simple/strict_strto* to kstrto*
Convert simple/strict_strto* functions to kstrto* functions. Only simple
cases are converted.
simple_strto* uses are still left to places where it is used to parse
numbers from a list of numbers. These need some other solution than
kstrto*.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Archit Taneja [Tue, 12 Apr 2011 08:22:26 +0000 (13:52 +0530)]
OMAP2PLUS: DSS2: Remove hack config "CONFIG_OMAP2_DSS_USE_DSI_PLL"
The clock sources for DISPC_FCLK and LCD1_CLK are now specified in the board file.
There is no need for the hack config "CONFIG_OMAP2_DSS_USE_DSI_PLL" anymore.
Introduce function dpi_use_dsi_pll() which checks for the clock sources to decide
whether DSI PLL is to be used or not.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Archit Taneja [Tue, 12 Apr 2011 08:22:25 +0000 (13:52 +0530)]
OMAP: DSS2: HDMI: Use dss_device clock configuration for HDMI PLL parameters
Move some of the configurable HDMI PLL parameters to dssdev.clock struct.
Cleanup the function hdmi_compute_pll() by using the parameters defined in the
board file and do some cosmetic modifications.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Archit Taneja [Tue, 12 Apr 2011 08:22:24 +0000 (13:52 +0530)]
OMAP2PLUS: DSS2: Add clock sources to dss device clock configuration
Add enum dss_clock_source in dssdev.clocks struct so that the clock sources can
be specified in the board file.
Replace hard coded clock sources in dsi.c, dpi.c and replace them with the new
clock source members in dssdev.clocks. Modify the sdp4430_lcd_device struct in
board-4430sdp.c to specify clock sources for DISPC_FCLK, LCD1_CLK and DSI1_FCLK.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Archit Taneja [Tue, 12 Apr 2011 08:22:23 +0000 (13:52 +0530)]
OMAP2PLUS: DSS2: Change enum "dss_clk_source" to "omap_dss_clk_source"
Change enum dss_clk_source to omap_dss_clock_source and move it to
'plat/display.h'. Change the enum members to attach "OMAP_" in the beginning.
These changes are done in order to specify the clock sources for DSS in the
board file.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Thu, 31 Mar 2011 09:03:51 +0000 (12:03 +0300)]
OMAP: DSS2: use __exit for selected panel drivers
We can use __exit for the driver remove function in plain dss panels
(ie. those that do not need i2c or spi).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Thu, 31 Mar 2011 09:34:06 +0000 (12:34 +0300)]
OMAP: DSS2: make omap_dss_(un)register_device static
omap_dss_register_device and omap_dss_unregister_device can only be
called from core.c, so we can make it static.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Thu, 28 Oct 2010 13:46:38 +0000 (16:46 +0300)]
OMAP: DSS2: VENC: Add missing start/stop_device calls
VENC code was missing omap_dss_start/stop_device calls. This didn't
cause any problems as VENC could not be compiled as a module, but
nevertheless it's better to add the calls.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Jani Nikula [Fri, 24 Sep 2010 09:16:24 +0000 (11:16 +0200)]
OMAP: DSS2: OMAPFB: Remove implicit display update on unblank
Currently omapfb does an implicit display update (for manual update
displays) on unblank.
There is no guarantee that the framebuffer contains a valid image when
unblank is called. When using manual update displays it is the
responsibility of the user space to update the display, and so it should
be in this case also.
This patch removes the implicit display update on unblank.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
[tomi.valkeinen@ti.com: improved description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Thu, 23 Sep 2010 08:18:44 +0000 (11:18 +0300)]
OMAP: DSS2: OMAPFB: Handle errors when initializing panel
Errors from the panel driver were ignored during panel initialization.
Handle the errors and fail accordingly.
Also move the display initialization to a separate function to make it
cleaner.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Jani Nikula [Wed, 16 Jun 2010 12:26:36 +0000 (15:26 +0300)]
OMAP: DSS2: Add method for querying display dimensions from DSS drivers
Add get_dimensions() to struct omap_dss_driver. Use the call, if supported
by the driver, in OMAPFB.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Wed, 2 Jun 2010 14:57:33 +0000 (17:57 +0300)]
OMAP: DSS2: VENC: Remove sleeps at venc enable/disable
VENC code had 50ms sleep after enabling the output and 100ms sleep after
disabling the output. I don't see any reason for these sleeps.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Wed, 2 Jun 2010 14:48:22 +0000 (17:48 +0300)]
OMAP: DSS2: VENC: make 20ms venc bug-fix sleep optional
There's a 20ms sleep after VENC reset. It's unknown what bug this
circumvents and on what platforms. Add a Kconfig option to disable the
sleep.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Wed, 2 Jun 2010 14:31:53 +0000 (17:31 +0300)]
OMAP: DSS2: make 50ms bug-fix sleep optional
For some unknown reason we may get SYNC_LOST errors from the display
subsystem at initialization time if we don't sleep before resetting the
DSS. See the source (dss.c) for more comments.
However, 50ms is quite long time to sleep, and with some configurations
the SYNC_LOST may never happen, so this patch creates a Kconfig option
to disable the sleep.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Thu, 20 May 2010 12:13:12 +0000 (15:13 +0300)]
OMAP: DSS2: remove non-working msleep(40) workaround
The sleep workaround for the problem described in the comment doesn't
really work. This patch removes the workaround, and improves the comment
about the bug, and proposes an userspace workaround.
omap_dss_set_manager() is called 6 times when loading omapdss and
omapfb, which means that 40ms * 6 = 240ms was spent sleeping when
booting up.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Tue, 22 Feb 2011 11:36:10 +0000 (13:36 +0200)]
OMAP: DSS2: move dss device clock configuration
Clock configuration was defined inside dssdev.phy.dsi struct. The clock
config doesn't really belong there, and so it's moved to dssdev.clock
struct.
Now the explicit clock configuration could also be used for other
interfaces than DSI, although there's no support for it currently.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Archit Taneja [Wed, 23 Mar 2011 09:59:34 +0000 (09:59 +0000)]
OMAP: DSS2: DSI: Introduce sync_vc functions
The DSI protocol engine has no interrupt for signalling the end of a Frame
transfer. The present approach is to send a BTA after DISPC generates a
FRAMEDONE interrupt, and unlock the dsi bus only when the BTA Ack is received.
The assumption made with this approach was that OMAP will send a BTA only after
the long packet corresponding to the last line is sent. However, it is possible
that on the DISPC FRAMEDONE interrupt there are 2 (or more) lines of pixel data
in the DSI line buffer. Hence, the BTA Ack could be received for the long packet
corresponding to the second last line (or the third last and so on..).
Therefore, the current method doesn't ensure that the complete frame data is
sent before we start a new transfer. A similar explanation holds valid if we
send a BTA in between multiple short/long command packets from the slave port.
Introduce dsi_sync_vc functions, based on Tomi Valkeinen's idea, which ensure
that the DSI Virtual Channel in use(update_channel) completes its previous work
before proceeding to the next Frame/Command.
For a frame update, the DSI driver now sends a callback to the Panel Driver
on the FRAMEDONE interrupt itself. The callback in the panel driver then unlocks
the bus. dsi_sync_vc() functions are placed in dsi_vc_config_l4() and
dsi_vc_config_vp() to ensure that the previous task of the Virtual Channel is
completed.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Archit Taneja [Tue, 22 Mar 2011 11:33:36 +0000 (06:33 -0500)]
OMAP4: DSS2: Register configuration changes for DSI
The following changes have changed from OMAP3 to OMAP4 DSI:
-The register field DSI_PLL_FREQSEL in DSI_PLL_CONFIGURATION2 has been removed.
-DCS_CMD_ENABLE and DCS_CMD_CODE bits have been moved from DSI_CTRL to
DSI_VC_CTRLi, hence the control of the bits is available per VC.
-DSI LDO powergood notification doesn't work on OMAP4. This is mentioned in
OMAP4 errata revision 1.8(Errata 1.76).
-OCP_WIDTH register field is included in DSI_VC_CTRL.
-The SCP clock is also required to access DSI PLL registers
Introduce dss features for these changes so that DSI runs on both OMAP3 and
OMAP4.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Fri, 8 Apr 2011 06:30:27 +0000 (09:30 +0300)]
OMAP: DSS2: fix panel Kconfig dependencies
All DPI panels were missing dependency to OMAP2_DSS_DPI. Add the
dependency.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Fri, 15 Apr 2011 07:42:59 +0000 (10:42 +0300)]
OMAP: DSS2: DSI: Fix DSI PLL power bug
OMAP3630 has a HW bug causing DSI PLL power command POWER_ON_DIV (0x3)
to not work properly. The bug prevents us from enabling DSI PLL power
only to HS divider block.
This patch adds a dss feature for the bug and converts POWER_ON_DIV
requests to POWER_ON_ALL (0x2).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Archit Taneja [Thu, 31 Mar 2011 07:53:35 +0000 (13:23 +0530)]
OMAP: DSS2: Fix: Return correct lcd clock source for OMAP2/3
dss.lcd_clk_source is set to the default value DSS_CLK_SRC_FCK at dss_init.
For OMAP2 and OMAP3, the dss.lcd_clk_source should always be the same as
dss.dispc_clk_source. The function dss_get_lcd_clk_source() always returns the
default value DSS_CLK_SRC_FCK for OMAP2/3. This leads to wrong clock dumps when
dispc_clk_source is not DSS_CLK_SRC_FCK.
Correct this function to always return dss.dispc_clk_source for OMAP2/3.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Mon, 4 Apr 2011 07:02:53 +0000 (10:02 +0300)]
OMAP: DSS2: DSI: fix dsi_dump_clocks()
On OMAP4, reading DSI_PLL_CONFIGURATION2 register requires the L3 clock
(CIO_CLK_ICG) to PLL. Currently dsi_dump_clocks() tries to read that
register without enabling the L3 clock, leading to crash if DSI is not
in use.
The status of the bit being read from DSI_PLL_CONFIGURATION2 is
available from dsi_clock_info->use_sys_clk, so we can avoid the whole
problem by just using that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Thu, 7 Apr 2011 12:28:47 +0000 (15:28 +0300)]
OMAP: DSS2: DSI: fix use_sys_clk & highfreq
use_sys_clk and highfreq fields in dsi.current_cinfo were never set.
Luckily they weren't used anywhere so it didn't cause any problems.
This patch fixes those fields and they are now set at the same time as
the rest of the fields.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Wed, 11 May 2011 11:10:07 +0000 (14:10 +0300)]
OMAP: DSS2: Move nokia-dsi-panel.h to include/video/
arch/arm/plat-omap/include/plat/nokia-dsi-panel.h is an include for the
OMAP DSS panel driver for Nokia's DSI displays. A more logical place for
it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Tue, 10 May 2011 16:48:10 +0000 (19:48 +0300)]
OMAP: DSS2: Move panel-generic-dpi.h to include/video/
arch/arm/plat-omap/include/plat/panel-generic-dpi.h is an include for
the OMAP DSS panel driver for generic DPI displays. A more logical place
for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Wed, 11 May 2011 11:05:07 +0000 (14:05 +0300)]
OMAP: DSS2: Move display.h to include/video/
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Linus Torvalds [Tue, 10 May 2011 02:33:54 +0000 (19:33 -0700)]
Linux 2.6.39-rc7
Hugh Dickins [Tue, 10 May 2011 00:44:42 +0000 (17:44 -0700)]
vm: fix vm_pgoff wrap in upward expansion
Commit
a626ca6a6564 ("vm: fix vm_pgoff wrap in stack expansion") fixed
the case of an expanding mapping causing vm_pgoff wrapping when you had
downward stack expansion. But there was another case where IA64 and
PA-RISC expand mappings: upward expansion.
This fixes that case too.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 9 May 2011 23:59:51 +0000 (16:59 -0700)]
Merge branch 'drm-intel-fixes' of git://git./linux/kernel/git/keithp/linux-2.6
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915/lvds: Only act on lid notify when the device is on
drm/i915: fix intel_crtc_clock_get pipe reads after "cleanup cleanup"
drm/i915: Only enable the plane after setting the fb base (pre-ILK)
drm/i915/dp: Be paranoid in case we disable a DP before it is attached
drm/i915: Release object along create user fb error path
Mikulas Patocka [Mon, 9 May 2011 11:01:09 +0000 (13:01 +0200)]
Don't lock guardpage if the stack is growing up
Linux kernel excludes guard page when performing mlock on a VMA with
down-growing stack. However, some architectures have up-growing stack
and locking the guard page should be excluded in this case too.
This patch fixes lvm2 on PA-RISC (and possibly other architectures with
up-growing stack). lvm2 calculates number of used pages when locking and
when unlocking and reports an internal error if the numbers mismatch.
[ Patch changed fairly extensively to also fix /proc/<pid>/maps for the
grows-up case, and to move things around a bit to clean it all up and
share the infrstructure with the /proc bits.
Tested on ia64 that has both grow-up and grow-down segments - Linus ]
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Tested-by: Tony Luck <tony.luck@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 9 May 2011 19:00:49 +0000 (12:00 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
eeepc-laptop: Use ACPI handle to identify rfkill port
[PATCH] sony-laptop: limit brightness range to DSDT provided ones
sony-laptop: report failures on setting LCD brightness
thinkpad-acpi: module autoloading for newer Lenovo ThinkPads.
Alex Williamson [Thu, 21 Apr 2011 22:08:14 +0000 (16:08 -0600)]
drm/i915/lvds: Only act on lid notify when the device is on
If we're using vga switcheroo, the device may be turned off
and poking it can return random state. This provokes an OOPS fixed
separately by
8ff887c847 (drm/i915/dp: Be paranoid in case we disable a
DP before it is attached). Trying to use and respond to events on a
device that has been turned off by the user is in principle a silly thing
to do.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
Chris Wilson [Fri, 22 Apr 2011 21:17:21 +0000 (22:17 +0100)]
drm/i915: fix intel_crtc_clock_get pipe reads after "cleanup cleanup"
Despite the fixes in
548f245ba6a31 (drm/i915: fix per-pipe reads after
"cleanup"), we missed one neighbouring read that was mistakenly replaced
with the reg value in
9db4a9c (drm/i915: cleanup per-pipe reg usage).
This was preventing us from correctly determining the mode the BIOS left
the panel in for machines that neither have an OpRegion nor access to
the VBT, (e.g. the EeePC 700).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Chris Wilson [Tue, 19 Apr 2011 20:14:14 +0000 (21:14 +0100)]
drm/i915: Only enable the plane after setting the fb base (pre-ILK)
When enabling the plane, it is helpful to have already pointed that
plane to valid memory or else we may incur the wrath of a PGTBL_ER.
This code preserved the behaviour from the bad old days for unknown
reasons...
Found by assert_fb_bound_for_plane().
References: https://bugs.freedesktop.org/show_bug.cgi?id=36246
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Linus Torvalds [Mon, 9 May 2011 16:13:10 +0000 (09:13 -0700)]
Merge branch 'fix/asoc' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: Fix CODEC DAI names for Goni
ASoC: Fix CODEC name in Goni
davinci-mcasp: fix _CBM_CFS pin directions
davinci-mcasp: fix _CBM_CFS hw_params
davinci-mcasp: use bitfield definitions for PDIR
ASoC: davinci-mcasp: correct tdm_slots limit
Linus Torvalds [Mon, 9 May 2011 16:09:04 +0000 (09:09 -0700)]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add pci id to acer travelmate quirk for 5730
drm/radeon: fix order of doing things in radeon_crtc_cursor_set
drm: mm: fix debug output
drm/radeon/kms: ATPX switcheroo fixes
drm/nouveau: Fix a crash at card takedown for NV40 and older cards
Linus Torvalds [Mon, 9 May 2011 16:07:55 +0000 (09:07 -0700)]
Merge branch 'hpfs'
* hpfs:
HPFS: Remove unused variable
HPFS: Move declaration up, so that there are no out-of-scope pointers
HPFS: Fix some unaligned accesses
HPFS: Fix endianity. Make hpfs work on big-endian machines
HPFS: Implement fsync for hpfs
HPFS: Fix a bug that filesystem was not marked dirty when remounting it
HPFS: Restrict uid and gid to 16-bit values
HPFS: When marking or clearing the dirty bit, sync the filesystem
HPFS: Use types with defined width
HPFS: Remove mark_inode_dirty
HPFS: Remove CR/LF conversion option
HPFS: Remove remaining locks
HPFS: Introduce a global mutex and lock it on every callback from VFS.
HPFS: Make HPFS compile on preempt and SMP
Mikulas Patocka [Sun, 8 May 2011 18:44:46 +0000 (20:44 +0200)]
HPFS: Remove unused variable
Remove unused variable
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Sun, 8 May 2011 18:44:38 +0000 (20:44 +0200)]
HPFS: Move declaration up, so that there are no out-of-scope pointers
Move declaration up, so that there are no out-of-scope pointers
Reported-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Sun, 8 May 2011 18:44:32 +0000 (20:44 +0200)]
HPFS: Fix some unaligned accesses
Fix some unaligned accesses
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Sun, 8 May 2011 18:44:26 +0000 (20:44 +0200)]
HPFS: Fix endianity. Make hpfs work on big-endian machines
Fix endianity. Make hpfs work on big-endian machines.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Sun, 8 May 2011 18:44:19 +0000 (20:44 +0200)]
HPFS: Implement fsync for hpfs
Implement fsync for hpfs.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Sun, 8 May 2011 18:44:08 +0000 (20:44 +0200)]
HPFS: Fix a bug that filesystem was not marked dirty when remounting it
Fix a bug that filesystem was not marked dirty when remounting it
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Sun, 8 May 2011 18:44:00 +0000 (20:44 +0200)]
HPFS: Restrict uid and gid to 16-bit values
Restrict uid and gid to 16-bit values.
HPFS stores only 2 bytes in the EAs.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Sun, 8 May 2011 18:43:41 +0000 (20:43 +0200)]
HPFS: When marking or clearing the dirty bit, sync the filesystem
When marking or clearing the dirty bit, sync the filesystem
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Sun, 8 May 2011 18:43:34 +0000 (20:43 +0200)]
HPFS: Use types with defined width
Use types with defined width
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Sun, 8 May 2011 18:43:27 +0000 (20:43 +0200)]
HPFS: Remove mark_inode_dirty
Remove mark_inode_dirty
HPFS doesn't use kernel's dirty inode indicator anyway because
writing an inode requires directory's mutex.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Sun, 8 May 2011 18:43:19 +0000 (20:43 +0200)]
HPFS: Remove CR/LF conversion option
Remove CR/LF conversion option
It is unused anyway. It was used on 2.2 kernels or so.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Sun, 8 May 2011 18:43:06 +0000 (20:43 +0200)]
HPFS: Remove remaining locks
Remove remaining locks
Because of a new global per-fs lock, no other locks are needed
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Sun, 8 May 2011 18:42:54 +0000 (20:42 +0200)]
HPFS: Introduce a global mutex and lock it on every callback from VFS.
Introduce a global mutex and lock it on every callback from VFS.
Performance doesn't matter, reviewing the whole code for locking correctness
would be too complicated, so simply lock it all.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Sun, 8 May 2011 18:42:44 +0000 (20:42 +0200)]
HPFS: Make HPFS compile on preempt and SMP
Make HPFS compile on preempt and SMP
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Garrett [Mon, 9 May 2011 14:44:01 +0000 (10:44 -0400)]
eeepc-laptop: Use ACPI handle to identify rfkill port
The ACPI notification we get from rfkill events on these machines gives
us all the information we need to identify the port that's changed. Do
so rather than assuming that it's always bus 1.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Mattia Dongili [Mon, 9 May 2011 14:20:29 +0000 (10:20 -0400)]
[PATCH] sony-laptop: limit brightness range to DSDT provided ones
The new style brightness control provides an operating range of 9 values
(seems consistent over a large number of models sharing the same
brightness control methods).
Read and use the minimum and maximum values to limit the backlight
interface between those boundaries.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Mattia Dongili [Tue, 5 Apr 2011 14:38:36 +0000 (23:38 +0900)]
sony-laptop: report failures on setting LCD brightness
Check if we were successful in setting the requested brightness and
report failure in that case.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Manoj Iyer [Sun, 8 May 2011 22:04:29 +0000 (18:04 -0400)]
thinkpad-acpi: module autoloading for newer Lenovo ThinkPads.
The newer Lenovo ThinkPads have HKEY HID of LEN0068 instead
of IBM0068. Added new HID so that thinkpad_acpi module will
auto load on these newer Lenovo ThinkPads.
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: stable@kernel.org
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Alex Deucher [Wed, 4 May 2011 15:41:47 +0000 (11:41 -0400)]
drm/radeon/kms: add pci id to acer travelmate quirk for 5730
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=34082
Reported by: Sampo Laaksonen <zhamahn@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Ilija Hadzic [Thu, 5 May 2011 00:15:03 +0000 (20:15 -0400)]
drm/radeon: fix order of doing things in radeon_crtc_cursor_set
if object pin or object lookup in radeon_cursor_set fail, the function
could leave inconsistent mouse width and hight values in radeon_crtc
fixed by moving cursor width and height assignments after all
checks have passed
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel Vetter [Fri, 6 May 2011 21:47:53 +0000 (23:47 +0200)]
drm: mm: fix debug output
The looping helper didn't do anything due to a superficial
semicolon. Furthermore one of the two dump functions suffered
from copy&paste fail.
While staring at the code I've also noticed that the replace
helper (currently unused) is a bit broken.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Sun, 8 May 2011 23:14:38 +0000 (09:14 +1000)]
Merge remote branch 'nouveau/drm-nouveau-fixes' of /ssd/git/drm-nouveau-next into drm-fixes
* 'nouveau/drm-nouveau-fixes' of /ssd/git/drm-nouveau-next:
drm/nouveau: Fix a crash at card takedown for NV40 and older cards
Alex Deucher [Fri, 6 May 2011 05:42:49 +0000 (01:42 -0400)]
drm/radeon/kms: ATPX switcheroo fixes
When we switch the display mux, also switch
the i2c mux. Also use the start and finish
methods to let the sbios know that the switch
is happening.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=35398
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Jimmy Rentz [Sun, 17 Apr 2011 20:15:09 +0000 (16:15 -0400)]
drm/nouveau: Fix a crash at card takedown for NV40 and older cards
NV40 and older cards (pre NV50) reserve a vram bo for the vga memory at
card init. This bo is then freed at card shutdown. The problem is that
the ttm bo vram manager was already freed. So a crash occurs when the
vga bo is freed. The fix is to free the vga bo prior to freeing the ttm
bo vram manager. There might be other solutions but this seemed the
simplest to me.
Signed-off-by: Jimmy Rentz <jb17bsome@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Linus Torvalds [Sat, 7 May 2011 20:17:37 +0000 (13:17 -0700)]
Merge branch 'perf-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Makefile: Use gcc to determine ARCH
perf events, x86: Fix Intel Nehalem and Westmere last level cache event definitions
hw_breakpoints, powerpc: Fix CONFIG_HAVE_HW_BREAKPOINT off-case in ptrace_set_debugreg()
sh, hw_breakpoints: Fix racy access to ptrace breakpoints
arm, hw_breakpoints: Fix racy access to ptrace breakpoints
powerpc, hw_breakpoints: Fix racy access to ptrace breakpoints
x86, hw_breakpoints: Fix racy access to ptrace breakpoints
ptrace: Prepare to fix racy accesses on task breakpoints
Lin Ming [Sat, 7 May 2011 04:41:14 +0000 (12:41 +0800)]
perf tools: Makefile: Use gcc to determine ARCH
The original Makefile uses "uname -m" to determine ARCH.
This causes problem on x86 when compile perf tool on 32 bit
userspace with a 64 bit kernel.
bench/../../../arch/x86/lib/memcpy_64.S: Assembler messages:
bench/../../../arch/x86/lib/memcpy_64.S:28: Error: bad register name `%rdi'
This is because "uname -m" returns x86_64 and memcpy_64.S is
included in 32 bit build.
Reported-by: Riccardo Magliocchetti <riccardo.magliocchetti@gmail.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Link: http://lkml.kernel.org/r/1304743274.3132.17.camel@localhost
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Fri, 6 May 2011 22:32:41 +0000 (15:32 -0700)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: handle errors from coalesce_t2
cifs: refactor mid finding loop in cifs_demultiplex_thread
cifs: sanitize length checking in coalesce_t2 (try #3)
cifs: check for bytes_remaining going to zero in CIFS_SessSetup
cifs: change bleft in decode_unicode_ssetup back to signed type
Arjan van de Ven [Fri, 6 May 2011 03:55:18 +0000 (23:55 -0400)]
Regression: partial revert "tracing: Remove lock_depth from event entry"
This partially reverts commit
e6e1e2593592a8f6f6380496655d8c6f67431266.
That commit changed the structure layout of the trace structure, which
in turn broke PowerTOP (1.9x generation) quite badly.
I appreciate not wanting to expose the variable in question, and
PowerTOP was not using it, so I've replaced the variable with just a
padding field - that way if in the future a new field is needed it can
just use this padding field.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 6 May 2011 17:01:54 +0000 (10:01 -0700)]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] fix oops in scsi_run_queue()
Timo Warns [Fri, 6 May 2011 11:47:35 +0000 (13:47 +0200)]
Validate size of EFI GUID partition entries.
Otherwise corrupted EFI partition tables can cause total confusion.
Signed-off-by: Timo Warns <warns@pre-sense.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Zijlstra [Fri, 22 Apr 2011 22:57:42 +0000 (00:57 +0200)]
perf events, x86: Fix Intel Nehalem and Westmere last level cache event definitions
The Intel Nehalem offcore bits implemented in:
e994d7d23a0b: perf: Fix LLC-* events on Intel Nehalem/Westmere
... are wrong: they implemented _ACCESS as _HIT and counted OTHER_CORE_HIT* as
MISS even though its clearly documented as an L3 hit ...
Fix them and the Westmere definitions as well.
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1299119690-13991-3-git-send-email-ming.m.lin@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Frederic Weisbecker [Thu, 5 May 2011 23:53:18 +0000 (01:53 +0200)]
hw_breakpoints, powerpc: Fix CONFIG_HAVE_HW_BREAKPOINT off-case in ptrace_set_debugreg()
We make use of ptrace_get_breakpoints() / ptrace_put_breakpoints() to
protect ptrace_set_debugreg() even if CONFIG_HAVE_HW_BREAKPOINT if off.
However in this case, these APIs are not implemented.
To fix this, push the protection down inside the relevant ifdef.
Best would be to export the code inside
CONFIG_HAVE_HW_BREAKPOINT into a standalone function to cleanup
the ifdefury there and call the breakpoint ref API inside. But
as it is more invasive, this should be rather made in an -rc1.
Fixes this build error:
arch/powerpc/kernel/ptrace.c:1594: error: implicit declaration of function 'ptrace_get_breakpoints' make[2]: ***
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: LPPC <linuxppc-dev@lists.ozlabs.org>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: v2.6.33.. <stable@kernel.org>
Link: http://lkml.kernel.org/r/1304639598-4707-1-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar [Fri, 6 May 2011 06:11:28 +0000 (08:11 +0200)]
Merge branch 'master' of ssh:///linux/kernel/git/torvalds/linux-2.6 into perf/urgent
Linus Torvalds [Fri, 6 May 2011 04:27:57 +0000 (21:27 -0700)]
Merge branch 'for-linus' of git://github.com/at91linux/linux-2.6-at91
* 'for-linus' of git://github.com/at91linux/linux-2.6-at91:
at91: Add ARCH_ID and basic cpu macros definition for 5series chips family.
arm: at91: fix compiler warning for eb01 board build
arm: at91: minimal defconfig for at91x40 SoC
ARM: at91: AT91CAP9 has a macb device
Linus Torvalds [Thu, 5 May 2011 04:30:28 +0000 (21:30 -0700)]
VM: skip the stack guard page lookup in get_user_pages only for mlock
The logic in __get_user_pages() used to skip the stack guard page lookup
whenever the caller wasn't interested in seeing what the actual page
was. But Michel Lespinasse points out that there are cases where we
don't care about the physical page itself (so 'pages' may be NULL), but
do want to make sure a page is mapped into the virtual address space.
So using the existence of the "pages" array as an indication of whether
to look up the guard page or not isn't actually so great, and we really
should just use the FOLL_MLOCK bit. But because that bit was only set
for the VM_LOCKED case (and not all vma's necessarily have it, even for
mlock()), we couldn't do that originally.
Fix that by moving the VM_LOCKED check deeper into the call-chain, which
actually simplifies many things. Now mlock() gets simpler, and we can
also check for FOLL_MLOCK in __get_user_pages() and the code ends up
much more straightforward.
Reported-and-reviewed-by: Michel Lespinasse <walken@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 4 May 2011 21:23:41 +0000 (14:23 -0700)]
Merge branch 'staging-linus' of git://git./linux/kernel/git/gregkh/staging-2.6
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
staging: Remove a warning for drivers/staging/wlan-ng/cfg80211.c
staging: intel_sst: intelmid needs delay.h
staging: solo6x10: add select SND_PCM to fix build error
staging: usbip: vhci: fix oops on subsequent attach
staging: ft1000: Remove unnecessary EXPORT_SYMBOLs
staging: rts_pstor: use #ifdef instead of #if
staging: rts_pstor: Add <linux/vmalloc.h>
staging: gma500: Depend on X86
staging: olpc: Add <linux/delay.h>
Linus Torvalds [Wed, 4 May 2011 21:22:53 +0000 (14:22 -0700)]
Merge branch 'usb-linus' of git://git./linux/kernel/git/gregkh/usb-2.6
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
xHCI: Clear PLC in xhci_bus_resume()
USB: fix regression in usbip by setting has_tt flag
usb/isp1760: Report correct urb status after unlink
omap:usb: add regulator support for EHCI
mfd: Fix usbhs_enable error handling
usb: musb: gadget: Fix out-of-sync runtime pm calls
usb: musb: omap2430: Fix retention idle on musb peripheral only boards
Linus Torvalds [Wed, 4 May 2011 21:22:20 +0000 (14:22 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: do not call __mark_dirty_inode under i_lock
libceph: fix ceph_osdc_alloc_request error checks
ceph: handle ceph_osdc_new_request failure in ceph_writepages_start
libceph: fix ceph_msg_new error path
ceph: use ihold() when i_lock is held
Linus Torvalds [Wed, 4 May 2011 21:22:04 +0000 (14:22 -0700)]
Merge branch 'v4l_for_linus' of git://git./linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] ngene: Fix CI data transfer regression Fix CI data transfer regression introduced by previous cleanup.
[media] v4l: make sure drivers supply a zeroed struct v4l2_subdev
[media] Missing frontend config for LME DM04/QQBOX
[media] rc_core: avoid kernel oops when rmmod saa7134
[media] imon: add conditional locking in change_protocol
[media] rc: show RC_TYPE_OTHER in sysfs
[media] ite-cir: modular build on ppc requires delay.h include
[media] mceusb: add Dell transceiver ID
Linus Torvalds [Wed, 4 May 2011 21:21:39 +0000 (14:21 -0700)]
Merge branch 'fixes' of git://git./linux/kernel/git/ieee1394/linux1394-2.6
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: Fix for broken configrom updates in quick succession
Linus Torvalds [Wed, 4 May 2011 21:21:08 +0000 (14:21 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
flex_arrays: allow zero length flex arrays
flex_array: flex_array_prealloc takes a number of elements, not an end
SELinux: pass last path component in may_create
Thomas Gleixner [Wed, 4 May 2011 13:38:19 +0000 (15:38 +0200)]
slub: Fix the lockless code on 32-bit platforms with no 64-bit cmpxchg
The SLUB allocator use of the cmpxchg_double logic was wrong: it
actually needs the irq-safe one.
That happens automatically when we use the native unlocked 'cmpxchg8b'
instruction, but when compiling the kernel for older x86 CPUs that do
not support that instruction, we fall back to the generic emulation
code.
And if you don't specify that you want the irq-safe version, the generic
code ends up just open-coding the cmpxchg8b equivalent without any
protection against interrupts or preemption. Which definitely doesn't
work for SLUB.
This was reported by Werner Landgraf <w.landgraf@ru.ru>, who saw
instability with his distro-kernel that was compiled to support pretty
much everything under the sun. Most big Linux distributions tend to
compile for PPro and later, and would never have noticed this problem.
This also fixes the prototypes for the irqsafe cmpxchg_double functions
to use 'bool' like they should.
[ Btw, that whole "generic code defaults to no protection" design just
sounds stupid - if the code needs no protection, there is no reason to
use "cmpxchg_double" to begin with. So we should probably just remove
the unprotected version entirely as pointless. - Linus ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reported-and-tested-by: werner <w.landgraf@ru.ru>
Acked-and-tested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1105041539050.3005@ionos
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sage Weil [Wed, 4 May 2011 18:33:47 +0000 (11:33 -0700)]
ceph: do not call __mark_dirty_inode under i_lock
The __mark_dirty_inode helper now takes i_lock as of
250df6ed. Fix the
one ceph callers that held i_lock (__ceph_mark_dirty_caps) to return the
flags value so that the callers can do it outside of i_lock.
Signed-off-by: Sage Weil <sage@newdream.net>
Chris Wilson [Sun, 17 Apr 2011 05:38:35 +0000 (06:38 +0100)]
drm/i915/dp: Be paranoid in case we disable a DP before it is attached
Given that the hardware may be left in a random condition by the BIOS,
it is conceivable that we then attempt to clear the DP_PIPEB_SELECT bit
without us ever enabling/attaching the DP encoder to a pipe. Thus
causing a NULL deference when we attempt to wait for a vblank on that
crtc.
Reported-and-tested-by: Bryan Christ <bryan.christ@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36314
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36456
Reported-and-tested-by: Bo Wang <bo.b.wang@intel.com>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
Chris Wilson [Sat, 16 Apr 2011 09:23:51 +0000 (10:23 +0100)]
drm/i915: Release object along create user fb error path
Reported-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
Ingo Molnar [Wed, 4 May 2011 18:33:42 +0000 (20:33 +0200)]
Merge branch 'perf/urgent' of git://git./linux/kernel/git/frederic/random-tracing into perf/urgent
Linus Torvalds [Wed, 4 May 2011 02:59:13 +0000 (19:59 -0700)]
Linux 2.6.39-rc6
James Morris [Wed, 4 May 2011 01:59:34 +0000 (11:59 +1000)]
Merge branch 'for-linus' of git://git.infradead.org/users/eparis/selinux into for-linus
Linus Torvalds [Wed, 4 May 2011 01:52:09 +0000 (18:52 -0700)]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: fix gart setup on fusion parts (v2)
drm: Send pending vblank events before disabling vblank.
drm/radeon: fix regression on atom cards with hardcoded EDID record.
drm/radeon/kms: add some new pci ids
Alex Deucher [Tue, 3 May 2011 23:28:02 +0000 (19:28 -0400)]
drm/radeon/kms: fix gart setup on fusion parts (v2)
Out of the entire GART/VM subsystem, the hw designers changed
the location of 3 regs.
v2: airlied: add parameter for userspace to work from.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Christopher James Halse Rogers [Wed, 27 Apr 2011 06:10:57 +0000 (16:10 +1000)]
drm: Send pending vblank events before disabling vblank.
This is the least-bad behaviour. It means that we signal the
vblank event before it actually happens, but since we're disabling
vblanks there's no guarantee that it will *ever* happen otherwise.
This prevents GL applications which use WaitMSC from hanging
indefinitely.
Signed-off-by: Christopher James Halse Rogers <christopher.halse.rogers@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Sun, 1 May 2011 10:16:30 +0000 (20:16 +1000)]
drm/radeon: fix regression on atom cards with hardcoded EDID record.
Since
fafcf94e2b5732d1e13b440291c53115d2b172e9 introduced an edid size, it seems to have broken this path.
This manifest as oops on T500 Lenovo laptops with dual graphics primarily.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=33812
cc: stable@kernel.org
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Tue, 3 May 2011 19:15:55 +0000 (15:15 -0400)]
drm/radeon/kms: add some new pci ids
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Tue, 3 May 2011 23:10:25 +0000 (16:10 -0700)]
logfs: initialize superblock entries earlier
In particular, s_freeing_list needs to be initialized early, since it is
used on some of the error paths when mounts fail. The mapping inode,
for example, would be initialized and then free'd on an error path
before s_freeing_list was initialized, but the inode drop operation
needs the s_freeing_list to be set up.
Normally you'd never see this, because not only is logfs fairly rare,
but a successful mount will never have any issues.
Reported-by: werner <w.landgraf@ru.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
James Bottomley [Sun, 1 May 2011 14:42:07 +0000 (09:42 -0500)]
[SCSI] fix oops in scsi_run_queue()
The recent commit closing the race window in device teardown:
commit
86cbfb5607d4b81b1a993ff689bbd2addd5d3a9b
Author: James Bottomley <James.Bottomley@suse.de>
Date: Fri Apr 22 10:39:59 2011 -0500
[SCSI] put stricter guards on queue dead checks
is causing a potential NULL deref in scsi_run_queue() because the
q->queuedata may already be NULL by the time this function is called.
Since we shouldn't be running a queue that is being torn down, simply
add a NULL check in scsi_run_queue() to forestall this.
Tested-by: Jim Schutt <jaschut@sandia.gov>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Harry Wei [Thu, 28 Apr 2011 01:30:01 +0000 (09:30 +0800)]
staging: Remove a warning for drivers/staging/wlan-ng/cfg80211.c
Hi us,
When i was compiling kernel, a warning happened to me.
The warning said like following.
drivers/staging/wlan-ng/cfg80211.c:709: warning: initialization from
incompatible pointer type.
See http://s1202.photobucket.com/albums/bb364/harrywei/?action=view¤t=patched2.png
for more details.
So i patch like following.
Signed-off-by: Harry Wei <harryxiyou@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andiry Xu [Tue, 19 Apr 2011 09:17:39 +0000 (17:17 +0800)]
xHCI: Clear PLC in xhci_bus_resume()
This patch clears PORT_PLC if xhci_bus_resume() resumes a previous suspended
port, because if a port transition from U3 to U0 state, it will report a
port link state change, and software should clear the corresponding PLC bit.
It also uses hcd->speed to check if a port is a USB2 protocol port.
The patch fixes the issue that USB keyboard can not wakeup system from
hibernation.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>