OSDN Git Service
Ville Syrjälä [Tue, 12 Feb 2013 20:01:38 +0000 (22:01 +0200)]
drm/i915: Print the pipe control page GTT address
We already print the HWS addresses during init, so do the same for the
pipe control page. Reduces guesswork when looking at hex addresses
later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Fri, 8 Feb 2013 14:35:38 +0000 (16:35 +0200)]
drm/i915: clean up panel fitter handling in lvds
With the previous patch "drm/i915: disable shared panel fitter for
pipe" we now disable the panel fitter at the right spot in the modeset
sequence in the crtc functions on all platforms. Hence the disabling
in intel_disable_lvds is no longer required and potentially harmful
(since the plane is still enabled at this point).
Similarly on the enabling side we enable the panel fitter in the lvds
callback only once the plane is enabled. Which is too late. Hence move
this into a new intel_pre_enable_lvds callback.
Finally we can ditch lvds_encoder->pfit_dirty - this was required to
work around the crtc helper semantics, but with the new i915 modeset
infrastructure we should enable/disable the pfit only when enabling or
disabling the entire output pipeline. So separate state tracking for
the pfit is no longer required.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Bikeshed the commit message a bit to stress that now we
enable/disable the pfit on i9xx platforms at the right point of time
compared to the old code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Fri, 8 Feb 2013 14:35:37 +0000 (16:35 +0200)]
drm/i915: disable shared panel fitter for pipe
If encoder is switched off by BIOS, but the panel fitter is left on,
we never try to turn off the panel fitter and leave it still attached
to the pipe - which can cause blurry output elsewhere.
Based on work by Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58867
Cc: stable@vger.kernel.org
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Tested-by: Andreas Sturmlechner <andreas.sturmlechner@gmail.com>
[danvet: Remove the redundant HAS_PCH_SPLIT check and add a tiny
comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sat, 9 Feb 2013 20:03:42 +0000 (21:03 +0100)]
drm/i915: detect wrong MCH watermark values
Some early bios versions seem to ship with the wrong tuning values for
the MCH, possible resulting in pipe underruns under load. Especially
on DP outputs this can lead to black screen, since DP really doesn't
like an occasional whack from an underrun.
Unfortunately the registers seem to be locked after boot, so the only
thing we can do is politely point out issues and suggest a BIOS
upgrade.
Arthur Runyan pointed us at this issue while discussion DP bugs - thus
far no confirmation from a bug report yet that it helps. But at least
some of my machines here have wrong values, so this might be useful in
understanding bug reports.
v2: After a bit more discussion with Art and Ben we've decided to only
the check the watermark values, since the OREF ones could be be a
notch more aggressive on certain machines.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Runyan, Arthur J <arthur.j.runyan@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Mon, 11 Feb 2013 21:31:27 +0000 (13:31 -0800)]
drm/i915/ctx: Remove bad invariant
It's not that the assertion is incorrect, but rather that we can call
do_destroy early in loading, and we will falsely BUG().
Since contexts have been in for a while now, and in the internal APIs
are pretty stable, it should be fairly safe to remove this.
v2: Remove unused dev_priv, and dev
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Fri, 8 Feb 2013 19:49:24 +0000 (11:49 -0800)]
drm/i915: Extract ring init from hw_init
The ring initialization will differ a bit in upcoming generations, and
this split will prepare the code for what's needed.
This patch also fixes a bug introduced in:
commit
99433931950f33039d9e1a52b4ed9af3f1b58e84
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Tue Jan 22 14:12:17 2013 +0200
drm/i915: use gem_set_seqno() on hardware init
After doing the extraction, the bad error handling became obvious. I
acknowledge that this should be two patches, but it's a pretty
small/trivial patch. If requested, I can certainly do the fix as a
distinct patch.
v2: Should be cleanup blt, not init blt on failure (Chris)
v3: Forgot to git add on v2
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Fri, 8 Feb 2013 19:32:47 +0000 (11:32 -0800)]
drm/i915: Fix gen2 mappable calculations
When I refactored the code initially, I forgot that gen2 uses a
different bar for the CPU mappable aperture. The agp-less code knows
nothing of generations less than 5, so we have to expand the gtt_probe
function to include the mappable base and end.
It was originally broken by me:
commit
baa09f5fd8a6d033ec075355dda99a65b7f6a0f3
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Thu Jan 24 13:49:57 2013 -0800
drm/i915: Add probe and remove to the gtt ops
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 8 Feb 2013 19:35:15 +0000 (17:35 -0200)]
drm/i915: add ibx_irq_postinstall
So we can remove duplicated code. Note that this function is used not
only on IBX, but also CPT and LPT.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Also bikeshed s/ironlake_enable_pch_hotplug/ibx_enable_hotplug
to keep consistent with our ibx for pch naming scheme.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 8 Feb 2013 21:13:35 +0000 (23:13 +0200)]
drm/i915: Fix sprite_scaling_enabled for multiple sprites
We have more than one sprite, so a boolean simply won't cut it.
Turn sprite_scaling_enabled into a bitmask and track the state
of sprite scaler for each sprite independently.
Also don't re-enable LP watermarks until the sprite registers
have actually been written, and thus sprite scaling has really
been disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 7 Feb 2013 11:42:32 +0000 (12:42 +0100)]
drm/i915: unify HDMI/DP hpd definitions
They're physically the same pins and also the same bits, duplicating
only confuses the reader. This also makes it a bit obvious that we
have quite some code duplication going on here. Squashing that is for
a larger rework in our hpd handling though.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Thu, 7 Feb 2013 21:34:19 +0000 (13:34 -0800)]
drm/i915: Clarify HW context size logic
This was a rebase error from when the patches originally landed. Since
the context size is unsigned, there is also no use in checking if it's
less than 0.
The existing code is not really wrong, but it's not simple as it should
be.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 6 Feb 2013 10:24:41 +0000 (11:24 +0100)]
drm/i915: write backlight harder
770c12312ad617172b1a65b911d3e6564fc5aca8 is the first bad commit
commit
770c12312ad617172b1a65b911d3e6564fc5aca8
Author: Takashi Iwai <tiwai@suse.de>
Date: Sat Aug 11 08:56:42 2012 +0200
drm/i915: Fix blank panel at reopening lid
changed the register write sequence for restoring the backlight, which
helped prevent non-working backlights on some machines. Turns out that
the original sequence was the right thing to do for a different set of
machines. Worse, setting the backlight level _after_ enabling it seems
to reset it somehow. So we need to make that one conditional upon the
backlight having been reset to zero, and add the old one back.
Cargo-culting at it's best, but it seems to work.
Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47941
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Zhang Rui [Tue, 5 Feb 2013 07:41:53 +0000 (15:41 +0800)]
i915: ignore lid open event when resuming
i915 driver needs to do modeset when
1. system resumes from sleep
2. lid is opened
In PM_SUSPEND_MEM state, all the GPEs are cleared when system resumes,
thus it is the i915_resume code does the modeset rather than intel_lid_notify().
But in PM_SUSPEND_FREEZE state, this will be broken because
system is still responsive to the lid events.
1. When we close the lid in Freeze state, intel_lid_notify() sets modeset_on_lid.
2. When we reopen the lid, intel_lid_notify() will do a modeset,
before the system is resumed.
here is the error log,
[92146.548074] WARNING: at drivers/gpu/drm/i915/intel_display.c:1028 intel_wait_for_pipe_off+0x184/0x190 [i915]()
[92146.548076] Hardware name: VGN-Z540N
[92146.548078] pipe_off wait timed out
[92146.548167] Modules linked in: hid_generic usbhid hid snd_hda_codec_realtek snd_hda_intel snd_hda_codec parport_pc snd_hwdep ppdev snd_pcm_oss i915 snd_mixer_oss snd_pcm arc4 iwldvm snd_seq_dummy mac80211 snd_seq_oss snd_seq_midi fbcon tileblit font bitblit softcursor drm_kms_helper snd_rawmidi snd_seq_midi_event coretemp drm snd_seq kvm btusb bluetooth snd_timer iwlwifi pcmcia tpm_infineon i2c_algo_bit joydev snd_seq_device intel_agp cfg80211 snd intel_gtt yenta_socket pcmcia_rsrc sony_laptop agpgart microcode psmouse tpm_tis serio_raw mxm_wmi soundcore snd_page_alloc tpm acpi_cpufreq lpc_ich pcmcia_core tpm_bios mperf processor lp parport firewire_ohci firewire_core crc_itu_t sdhci_pci sdhci thermal e1000e
[92146.548173] Pid: 4304, comm: kworker/0:0 Tainted: G W 3.8.0-rc3-s0i3-v3-test+ #9
[92146.548175] Call Trace:
[92146.548189] [<
c10378e2>] warn_slowpath_common+0x72/0xa0
[92146.548227] [<
f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548263] [<
f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548270] [<
c10379b3>] warn_slowpath_fmt+0x33/0x40
[92146.548307] [<
f86398b4>] intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548344] [<
f86399c2>] intel_disable_pipe+0x102/0x190 [i915]
[92146.548380] [<
f8639ea4>] ? intel_disable_plane+0x64/0x80 [i915]
[92146.548417] [<
f8639f7c>] i9xx_crtc_disable+0xbc/0x150 [i915]
[92146.548456] [<
f863ebee>] intel_crtc_update_dpms+0x5e/0x90 [i915]
[92146.548493] [<
f86437cf>] intel_modeset_setup_hw_state+0x42f/0x8f0 [i915]
[92146.548535] [<
f8645b0b>] intel_lid_notify+0x9b/0xc0 [i915]
[92146.548543] [<
c15610d3>] notifier_call_chain+0x43/0x60
[92146.548550] [<
c105d1e1>] __blocking_notifier_call_chain+0x41/0x80
[92146.548556] [<
c105d23f>] blocking_notifier_call_chain+0x1f/0x30
[92146.548563] [<
c131a684>] acpi_lid_send_state+0x78/0xa4
[92146.548569] [<
c131aa9e>] acpi_button_notify+0x3b/0xf1
[92146.548577] [<
c12df56a>] ? acpi_os_execute+0x17/0x19
[92146.548582] [<
c12e591a>] ? acpi_ec_sync_query+0xa5/0xbc
[92146.548589] [<
c12e2b82>] acpi_device_notify+0x16/0x18
[92146.548595] [<
c12f4904>] acpi_ev_notify_dispatch+0x38/0x4f
[92146.548600] [<
c12df0e8>] acpi_os_execute_deferred+0x20/0x2b
[92146.548607] [<
c1051208>] process_one_work+0x128/0x3f0
[92146.548613] [<
c1564f73>] ? common_interrupt+0x33/0x38
[92146.548618] [<
c104f8c0>] ? wake_up_worker+0x30/0x30
[92146.548624] [<
c12df0c8>] ? acpi_os_wait_events_complete+0x1e/0x1e
[92146.548629] [<
c10524f9>] worker_thread+0x119/0x3b0
[92146.548634] [<
c10523e0>] ? manage_workers+0x240/0x240
[92146.548640] [<
c1056e84>] kthread+0x94/0xa0
[92146.548647] [<
c1060000>] ? ftrace_raw_output_sched_stat_runtime+0x70/0xf0
[92146.548652] [<
c15649b7>] ret_from_kernel_thread+0x1b/0x28
[92146.548658] [<
c1056df0>] ? kthread_create_on_node+0xc0/0xc0
three different modeset flags are introduced in this patch
MODESET_ON_LID_OPEN: do modeset on next lid open event
MODESET_DONE: modeset already done
MODESET_SUSPENDED: suspended, only do modeset when system is resumed
In this way,
1. when lid is closed, MODESET_ON_LID_OPEN is set so that
we'll do modeset on next lid open event.
2. when lid is opened, MODESET_DONE is set
so that duplicate lid open events will be ignored.
3. when system suspends, MODESET_SUSPENDED is set.
In this case, we will not do modeset on any lid events.
Plus, locking mechanism is also introduced to avoid racing.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Sat, 2 Feb 2013 00:41:14 +0000 (16:41 -0800)]
drm/i915: Fix RC6VIDS encode/decode
The RC6 VIDS has a linear ramp starting at 250mv, which means any values
below 250 are invalid. The old buggy macros tried to adjust for this to
be more flexible, but there is no need. As Dan pointed out the ENCODE
only ever has one value. The only invalid value for decode is an input
of 0 which means something is really wonky, and the cases where DECODE
are used either don't matter (debug values), or would be implicitly
correct (the check for less than 450).
This patch makes simpler, easier to read macros which are actually
correct. Maybe this patch can actually fix some bugs now.
Thanks to Dan for catching this. /me hides
Cc: stable@kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 13 Feb 2013 10:37:48 +0000 (20:37 +1000)]
Revert "drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S"
This reverts commit
6f33814bd4d9cfe76033a31b1c0c76c960cd8e4b.
The quirk cause a regression, and it looks like the original bug was
simply a lack of FIFO bandwidth on the i915G of the reporter. Which
should eventually be fixed as soon as we get around to implemented
DSPARB FIFO reassignment on gen 3.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52281
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 8 Feb 2013 04:02:32 +0000 (14:02 +1000)]
Merge branch 'for-airlied' of git://people.freedesktop.org/~mlankhorst/linux into drm-next
TTM reservations changes, preparing for new reservation mutex system.
* 'for-airlied' of git://people.freedesktop.org/~mlankhorst/linux:
drm/ttm: unexport ttm_bo_wait_unreserved
drm/nouveau: use ttm_bo_reserve_slowpath in validate_init, v2
drm/ttm: use ttm_bo_reserve_slowpath_nolru in ttm_eu_reserve_buffers, v2
drm/ttm: add ttm_bo_reserve_slowpath
drm/ttm: cleanup ttm_eu_reserve_buffers handling
drm/ttm: remove lru_lock around ttm_bo_reserve
drm/nouveau: increase reservation sequence every retry
drm/vmwgfx: always use ttm_bo_is_reserved
Daniel Kurtz [Thu, 27 Dec 2012 01:01:46 +0000 (01:01 +0000)]
drm: make frame duration time calculation more precise
It is a bit more precise to compute the total number of pixels first and
then divide, rather than multiplying the line pixel count by the
already-rounded line duration.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Bjorn Helgaas [Fri, 4 Jan 2013 19:10:42 +0000 (19:10 +0000)]
drm/pci: Use PCI Express Capability accessors
Use PCI Express Capability access functions to simplify this code a bit.
For non-PCIe devices or pre-PCIe 3.0 devices that don't implement the Link
Capabilities 2 register, pcie_capability_read_dword() reads a zero.
Since we're only testing whether the bits we care about are set, there's no
need to mask out the other bits we *don't* care about.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Bjorn Helgaas [Fri, 4 Jan 2013 19:10:37 +0000 (19:10 +0000)]
drm/pci: Set all supported speeds in speed cap mask for pre-3.0 devices
For devices that conform to PCIe r3.0 and have a Link Capabilities 2
register, we test and report every bit in the Supported Link Speeds Vector
field. For a device that supports both 2.5GT/s and 5.0GT/s, we set both
DRM_PCIE_SPEED_25 and DRM_PCIE_SPEED_50 in the returned mask.
For pre-r3.0 devices, the Link Capabilities 0010b encoding
(PCI_EXP_LNKCAP_SLS_5_0GB) means that both 5.0GT/s and 2.5GT/s are
supported, so set both DRM_PCIE_SPEED_25 and DRM_PCIE_SPEED_50 in this
case as well.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Bjorn Helgaas [Fri, 4 Jan 2013 19:10:32 +0000 (19:10 +0000)]
drm/pci: Use the standard #defines for PCIe Link Capability bits
Use the standard #defines rather than bare numbers for the PCIe Link
Capabilities speed bits.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Thierry Reding [Mon, 14 Jan 2013 16:05:56 +0000 (16:05 +0000)]
drm: Allow vblank support without DRIVER_HAVE_IRQ
Drivers that register interrupt handlers without the DRM core helpers
don't initialize the .irq_enabled field and drm_dev_to_irq() may fail
when called on them. This shouldn't preclude them from implementing
the vblank IOCTL.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Aaron Plattner [Tue, 15 Jan 2013 20:47:44 +0000 (20:47 +0000)]
drm/radeon: use prime helpers
Simplify the Radeon prime implementation by using the default behavior provided
by drm_gem_prime_import and drm_gem_prime_export.
v2:
- Rename functions to radeon_gem_prime_get_sg_table and
radeon_gem_prime_import_sg_table.
- Delete the now-unused vmapping_count variable.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Aaron Plattner [Tue, 15 Jan 2013 20:47:43 +0000 (20:47 +0000)]
drm/nouveau: use prime helpers
Simplify the Nouveau prime implementation by using the default behavior provided
by drm_gem_prime_import and drm_gem_prime_export.
v2: Rename functions to nouveau_gem_prime_get_sg_table and
nouveau_gem_prime_import_sg_table.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Aaron Plattner [Tue, 15 Jan 2013 20:47:42 +0000 (20:47 +0000)]
drm: add prime helpers
Instead of reimplementing all of the dma_buf functionality in every driver,
create helpers drm_prime_import and drm_prime_export that implement them in
terms of new, lower-level hook functions:
gem_prime_pin: callback when a buffer is created, used to pin buffers into GTT
gem_prime_get_sg_table: convert a drm_gem_object to an sg_table for export
gem_prime_import_sg_table: convert an sg_table into a drm_gem_object
gem_prime_vmap, gem_prime_vunmap: map and unmap an object
These hooks are optional; drivers can opt in by using drm_gem_prime_import and
drm_gem_prime_export as the .gem_prime_import and .gem_prime_export fields of
struct drm_driver.
v2:
- Drop .begin_cpu_access. None of the drivers this code replaces implemented
it. Having it here was a leftover from when I was trying to include i915 in
this rework.
- Use mutex_lock instead of mutex_lock_interruptible, as these three drivers
did. This patch series shouldn't change that behavior.
- Rename helpers to gem_prime_get_sg_table and gem_prime_import_sg_table.
Rename struct sg_table* variables to 'sgt' for clarity.
- Update drm.tmpl for these new hooks.
v3:
- Pass the vaddr down to the driver. This lets drivers that just call vunmap on
the pointer avoid having to store the pointer in their GEM private structures.
- Move documentation into a /** DOC */ comment in drm_prime.c and include it in
drm.tmpl with a !P line. I tried to use !F lines to include documentation of
the individual functions from drmP.h, but the docproc / kernel-doc scripts
barf on that file, so hopefully this is good enough for now.
- apply refcount fix from commit
be8a42ae60addd8b6092535c11b42d099d6470ec
("drm/prime: drop reference on imported dma-buf come from gem")
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rob Clark [Thu, 24 Jan 2013 21:46:07 +0000 (21:46 +0000)]
drm/i2c: give i2c it's own Kconfig
Move this out of nouveau directory. As we start to add more encoder
slaves used by other drivers, it makes sense to put the Kconfig bits in
one place.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 8 Feb 2013 03:27:28 +0000 (13:27 +1000)]
Merge branch 'drm-next-3.9' of git://people.freedesktop.org/~agd5f/linux into drm-next
Alex writes:
- CS ioctl cleanup and unification. Unification of a lot of functionality
that was duplicated across multiple generates of hardware.
- Add support for Oland GPUs
- Deprecate UMS support. Mesa and the ddx dropped support for UMS and
apparently very few people still use it since the UMS CS ioctl was broken
for several kernels and no one reported it. It was fixed in 3.8/stable.
- Rework GPU reset. Use the status registers to determine what blocks
to reset. This better matches the recommended reset programming model.
This also allows us to properly reset blocks besides GFX and DMA.
- Switch the VM set page code to use an IB rather than the ring. This
fixes overflow issues when doing large page table updates using a small
ring like DMA.
- Several small cleanups and bug fixes.
* 'drm-next-3.9' of git://people.freedesktop.org/~agd5f/linux: (38 commits)
drm/radeon/dce6: fix display powergating
drm/radeon: add Oland pci ids
drm/radeon: radeon-asic updates for Oland
drm/radeon: add ucode loading support for Oland
drm/radeon: fill in gpu init for Oland
drm/radeon: add Oland chip family
drm/radeon: switch back to using the DMA ring for VM PT updates
drm/radeon: use IBs for VM page table updates v2
drm/radeon: don't reset the MC on IGPs/APUs
drm/radeon: use the reset mask to determine if rings are hung
drm/radeon: halt engines before disabling MC (si)
drm/radeon: halt engines before disabling MC (cayman/TN)
drm/radeon: halt engines before disabling MC (evergreen)
drm/radeon: halt engines before disabling MC (6xx/7xx)
drm/radeon: use status regs to determine what to reset (si)
drm/radeon: use status regs to determine what to reset (cayman)
drm/radeon: use status regs to determine what to reset (evergreen)
drm/radeon: use status regs to determine what to reset (6xx/7xx)
drm/radeon: rework GPU reset on cayman/TN
drm/radeon: rework GPU reset on cayman/TN
...
Dave Airlie [Fri, 8 Feb 2013 02:34:44 +0000 (12:34 +1000)]
Merge tag 'of_videomode_helper' of git://git.pengutronix.de/git/str/linux into drm-next
videomode helpers for of + devicetree stuff, required for new kms drivers
(not the fbdev maintainer).
* tag 'of_videomode_helper' of git://git.pengutronix.de/git/str/linux:
drm_modes: add of_videomode helpers
drm_modes: add videomode helpers
fbmon: add of_videomode helpers
fbmon: add videomode helpers
video: add of helper for display timings/videomode
video: add display_timing and videomode
viafb: rename display_timing to via_display_timing
Dave Airlie [Fri, 8 Feb 2013 02:14:50 +0000 (12:14 +1000)]
Merge branch 'udl-fixes' into drm-next
Fixes for usb/udl devices
* udl-fixes:
drm/udl: disable fb_defio by default
drm/udl: Inline memcmp() for RLE compression of xfer
drm/udl: make usage as a console safer
drm/usb: bind driver to correct device
Dave Airlie [Fri, 8 Feb 2013 02:13:43 +0000 (12:13 +1000)]
Merge branch 'console-fixes' into drm-next
(not the fbcon maintainer pull 2)
fix bug in vgacon on bootup and fbcon losing fonts on startup.
* console-fixes: (50 commits)
fbcon: don't lose the console font across generic->chip driver switch
vgacon/vt: clear buffer attributes when we load a 512 character font (v2)
Dave Airlie [Fri, 8 Feb 2013 02:10:18 +0000 (12:10 +1000)]
Merge branch 'fbcon-locking-fixes' of ssh://people.freedesktop.org/~airlied/linux into drm-next
This pulls in most of Linus tree up to -rc6, this fixes the worst lockdep
reported issues and re-enables fbcon lockdep.
(not the fbcon maintainer)
* 'fbcon-locking-fixes' of ssh://people.freedesktop.org/~airlied/linux: (529 commits)
Revert "Revert "console: implement lockdep support for console_lock""
fbcon: fix locking harder
fb: Yet another band-aid for fixing lockdep mess
fb: rework locking to fix lock ordering on takeover
Dave Airlie [Fri, 8 Feb 2013 02:07:01 +0000 (12:07 +1000)]
Revert "Revert "console: implement lockdep support for console_lock""
This reverts commit
ff0d05bf73620eb7dc8aee7423e992ef87870bdf.
Now that we have all the locking fixes in place, we can revert the
revert. This re-enables lockdep tracking for the console lock,
daee779718a319ff9f83e1ba3339334ac650bb22.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 25 Jan 2013 01:38:56 +0000 (11:38 +1000)]
fbcon: fix locking harder
Okay so Alan's patch handled the case where there was no registered fbcon,
however the other path entered in set_con2fb_map pit.
In there we called fbcon_takeover, but we also took the console lock in a couple
of places. So push the console lock out to the callers of set_con2fb_map,
this means fbmem and switcheroo needed to take the lock around the fb notifier
entry points that lead to this.
This should fix the efifb regression seen by Maarten.
Tested-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Tested-by: Lu Hua <huax.lu@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Takashi Iwai [Fri, 25 Jan 2013 00:28:18 +0000 (10:28 +1000)]
fb: Yet another band-aid for fixing lockdep mess
I've still got lockdep warnings even after Alan's patch, and it seems that
yet more band aids are required to paper over similar paths for
unbind_con_driver() and unregister_con_driver(). After this hack, lockdep
warnings are finally gone.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: stable <stable@vger.kernel.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alan Cox [Fri, 25 Jan 2013 00:28:15 +0000 (10:28 +1000)]
fb: rework locking to fix lock ordering on takeover
Adjust the console layer to allow a take over call where the caller
already holds the locks. Make the fb layer lock in order.
This is partly a band aid, the fb layer is terminally confused about the
locking rules it uses for its notifiers it seems.
[akpm@linux-foundation.org: remove stray non-ascii char, tidy comment]
[akpm@linux-foundation.org: export do_take_over_console()]
[airlied: cleanup another non-ascii char]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: stable <stable@vger.kernel.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Borislav Petkov [Mon, 4 Feb 2013 09:13:15 +0000 (10:13 +0100)]
x86/intel/cacheinfo: Shut up annoying warning
I've been getting the following warning when doing randbuilds
since forever. Now it finally pissed me off just the perfect
amount so that I can fix it.
arch/x86/kernel/cpu/intel_cacheinfo.c:489:27: warning: ‘cache_disable_0’ defined but not used [-Wunused-variable]
arch/x86/kernel/cpu/intel_cacheinfo.c:491:27: warning: ‘cache_disable_1’ defined but not used [-Wunused-variable] arch/x86/kernel/cpu/intel_cacheinfo.c:524:27: warning: ‘subcaches’ defined but not used [-Wunused-variable]
It happens because in randconfigs where CONFIG_SYSFS is not set,
the whole sysfs-interface to L3 cache index disabling is
remaining unused and gcc correctly warns about it. Make it
optional, depending on CONFIG_SYSFS too, as is the case with
other sysfs-related machinery in this file.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Link: http://lkml.kernel.org/r/1359969195-27362-1-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
H. Peter Anvin [Fri, 1 Feb 2013 04:23:49 +0000 (20:23 -0800)]
x86, doc: Boot protocol 2.12 is in 3.8
The boot protocol 2.12 changes were pulled for 3.8, so update the
documentation accordingly.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Jan Beulich [Wed, 30 Jan 2013 07:55:53 +0000 (07:55 +0000)]
x86-64: Replace left over sti/cli in ia32 audit exit code
For some reason they didn't get replaced so far by their
paravirt equivalents, resulting in code to be run with
interrupts disabled that doesn't expect so (causing, in the
observed case, a BUG_ON() to trigger) when syscall auditing is
enabled.
David (Cc-ed) came up with an identical fix, so likely this can
be taken to count as an ack from him.
Reported-by: Peter Moody <pmoody@google.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/5108E01902000078000BA9C5@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Tested-by: Peter Moody <pmoody@google.com>
Dave Airlie [Thu, 7 Feb 2013 02:30:25 +0000 (12:30 +1000)]
drm/udl: disable fb_defio by default
There seems to be a bad interaction between gem/shmem and defio on top,
I get list corruption on the page lru in the shmem code.
Turn it off for now until we get some more digging done.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Chris Wilson [Fri, 18 Jan 2013 16:31:14 +0000 (16:31 +0000)]
drm/udl: Inline memcmp() for RLE compression of xfer
As we use a variable length the compiler does not realise that it is a
fixed value of either 2 or 4 bytes. Instead of performing the inline
comparison itself, the compiler inserts a function call to the generic
memcmp routine which is optimised for long comparisons of variable
length. That turns out to be quite expensive...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 8 Feb 2013 01:08:10 +0000 (11:08 +1000)]
Merge tag 'drm-intel-next-2013-02-01' of git://people.freedesktop.org/~danvet/drm-intel into drm-next
Daniel writes:
"Probably the last feature pull for 3.9, there's some fixes outstanding
thought that I'd like to sneak in. And maybe 3.8 takes a bit longer ...
Anyway, highlights of this pull:
- Kill the horrible IS_DISPLAYREG hack to handle the mmio offset movements
on vlv, big thanks to Ville.
- Dynamic power well support for Haswell, shaves away a bit when only
using the eDP port on pipe A (Paulo). Plus unclaimed register fixes
uncovered by this.
- Clarifications of the gpu hang/reset state transitions, hopefully fixing
a few spurious -EIO deaths in userspace.
- Haswell ELD fixes.
- Some more (pp)gtt cleanups from Ben.
- A few smaller things all over.
Plus all the stuff from the previous rather small pull request:
- Broadcast RBG improvements and reduced color range fixes from Ville.
- Ben is on a "kill legacy gtt code for good" spree, first pile of patches
included.
- No-relocs and bo lut improvements for faster execbuf from Chris.
- Some refactorings from Imre."
* tag 'drm-intel-next-2013-02-01' of git://people.freedesktop.org/~danvet/drm-intel: (101 commits)
GPU/i915: Fix acpi_bus_get_device() check in drivers/gpu/drm/i915/intel_opregion.c
drm/i915: Set the SR01 "screen off" bit in i915_redisable_vga() too
drm/i915: Kill IS_DISPLAYREG()
drm/i915: Introduce i915_vgacntrl_reg()
drm/i915: gen6_gmch_remove can be static
drm/i915: dynamic Haswell display power well support
drm/i915: check the power down well on assert_pipe()
drm/i915: don't send DP "idle" pattern before "normal" on HSW PORT_A
drm/i915: don't run hsw power well code on !hsw
drm/i915: kill cargo-culted locking from power well code
drm/i915: Only run idle processing from i915_gem_retire_requests_worker
drm/i915: Fix CAGF for HSW
drm/i915: Reclaim GTT space for failed PPGTT
drm/i915: remove intel_gtt structure
drm/i915: Add probe and remove to the gtt ops
drm/i915: extract hw ppgtt setup/cleanup code
drm/i915: pte_encode is gen6+
drm/i915: vfuncs for ppgtt
drm/i915: vfuncs for gtt_clear_range/insert_entries
drm/i915: Error state should print /sys/kernel/debug
...
Dave Airlie [Thu, 7 Feb 2013 01:19:15 +0000 (11:19 +1000)]
drm/udl: make usage as a console safer
Okay you don't really want to use udl devices as your console, but if
you are unlucky enough to do so, you run into a lot of schedule while atomic
due to printk being called from all sorts of funky places. So check if we
are in an atomic context, and queue the damage for later, the next printk
should cause it to appear. This isn't ideal, but it is simple, and seems to
work okay in my testing here.
(dirty area idea came from xenfb)
fixes a bunch of sleeping while atomic issues running fbcon on udl devices.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 7 Feb 2013 00:10:04 +0000 (10:10 +1000)]
drm/usb: bind driver to correct device
While looking at plymouth on udl I noticed that plymouth was trying
to use its fb plugin not its drm one, it was trying to drmOpen a driver called
usb not udl, noticed that we actually had out driver pointing at the wrong
device.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 24 Jan 2013 06:12:41 +0000 (16:12 +1000)]
fbcon: don't lose the console font across generic->chip driver switch
If grub2 loads efifb/vesafb, then when systemd starts it can set the console
font on that framebuffer device, however when we then load the native KMS
driver, the first thing it does is tear down the generic framebuffer driver.
The thing is the generic code is doing the right thing, it frees the font
because otherwise it would leak memory. However we can assume that if you
are removing the generic firmware driver (vesa/efi/offb), that a new driver
*should* be loading soon after, so we effectively leak the font.
However the old code left a dangling pointer in vc->vc_font.data and we
can now reuse that dangling pointer to load the font into the new
driver, now that we aren't freeing it.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=892340
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 24 Jan 2013 04:14:19 +0000 (14:14 +1000)]
vgacon/vt: clear buffer attributes when we load a 512 character font (v2)
When we switch from 256->512 byte font rendering mode, it means the
current contents of the screen is being reinterpreted. The bit that holds
the high bit of the 9-bit font, may have been previously set, and thus
the new font misrenders.
The problem case we see is grub2 writes spaces with the bit set, so it
ends up with data like 0x820, which gets reinterpreted into 0x120 char
which the font translates into G with a circumflex. This flashes up on
screen at boot and is quite ugly.
A current side effect of this patch though is that any rendering on the
screen changes color to a slightly darker color, but at least the screen
no longer corrupts.
v2: as suggested by hpa, always clear the attribute space, whether we
are are going to or from 512 chars.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Tue, 5 Feb 2013 16:47:09 +0000 (11:47 -0500)]
drm/radeon/dce6: fix display powergating
Only enable it when we disable the display rather than
at DPMS time since enabling it requires a full modeset
to restore the display state. Fixes blank screens in
certain cases.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Linus Torvalds [Tue, 5 Feb 2013 21:36:12 +0000 (08:36 +1100)]
Merge branch 'v4l_for_linus' of git://git./linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"For a regression fix on a few radio drivers that were preventing radio
TX to work on those devices"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] radio: set vfl_dir correctly to fix modulator regression
Linus Torvalds [Tue, 5 Feb 2013 21:32:32 +0000 (08:32 +1100)]
Merge tag 'usb-3.8-rc6' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a few tiny USB fixes for 3.8-rc6.
Nothing major here, some host controller bug fixes to resolve a number
of bugs that people have reported, and a bunch of additional device
ids are added to a number of drivers (which caused code to be deleted
from the usb-storage driver, always nice)"
* tag 'usb-3.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
USB: storage: optimize to match the Huawei USB storage devices and support new switch command
USB: storage: Define a new macro for USB storage match rules
USB: ftdi_sio: add Zolix FTDI PID
USB: option: add Changhong CH690
USB: ftdi_sio: add PID/VID entries for ELV WS 300 PC II
USB: add OWL CM-160 support to cp210x driver
USB: EHCI: fix bug in scheduling periodic split transfers
USB: EHCI: fix for leaking isochronous data
USB: option: add support for Telit LE920
USB: qcserial: add Telit Gobi QDL device
USB: EHCI: fix timer bug affecting port resume
USB: UHCI: notify usbcore about port resumes
USB: EHCI: notify usbcore about port resumes
USB: add usb_hcd_{start,end}_port_resume
USB: EHCI: unlink one async QH at a time
USB: EHCI: remove ASS/PSS polling timeout
usb: Using correct way to clear usb3.0 device's remote wakeup feature.
usb: Prevent dead ports when xhci is not enabled
USB: XHCI: fix memory leak of URB-private data
drivers: xhci: fix incorrect bit test
...
Linus Torvalds [Tue, 5 Feb 2013 21:23:47 +0000 (08:23 +1100)]
Merge branch 'fixes-for-v3.8-rc7' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull DMA mapping fixes from Marek Szyprowski:
"This pull request contains important bugfix patches for 9
architectures, which finally fixes broken allmodconfig builds
introduced in v3.8-rc1. Those architectures don't use dma_map_ops
based implementation and require manual update or additional dummy
implementations of the missing new dma-mapping api functions:
dma_mmap_coherent and dma_get_sgtable."
* 'fixes-for-v3.8-rc7' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
xtensa: Provide dummy dma_mmap_coherent() and dma_get_sgtable()
parisc: Provide dummy dma_mmap_coherent() and dma_get_sgtable()
mn10300: Provide dummy dma_mmap_coherent() and dma_get_sgtable()
m68k: Provide dma_mmap_coherent() and dma_get_sgtable()
frv: Provide dummy dma_mmap_coherent() and dma_get_sgtable()
cris: Provide dma_mmap_coherent() and dma_get_sgtable()
c6x: Provide dummy dma_mmap_coherent() and dma_get_sgtable()
blackfin: Provide dma_mmap_coherent() and dma_get_sgtable()
avr32: Provide dma_mmap_coherent() and dma_get_sgtable()
Linus Torvalds [Tue, 5 Feb 2013 09:50:11 +0000 (20:50 +1100)]
Merge branch 'fix-max-write' of git://git./linux/kernel/git/teigland/linux-dlm
Pull dlm fix from David Teigland:
"Thanks to Jana who reported the problem and was able to test this fix
so quickly."
This fixes an incorrect size check that triggered for CONFIG_COMPAT
whether the code was actually doing compat or not. The incorrect write
size check broke userland (clvmd) when maximum resource name lengths are
used.
* 'fix-max-write' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
dlm: check the write size from user
Linus Torvalds [Tue, 5 Feb 2013 09:38:59 +0000 (20:38 +1100)]
Merge branch 'akpm' (Andrew's patch-bomb)
Merge mix fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (12 commits)
drivers/rtc/rtc-pl031.c: fix the missing operation on enable
drivers/rtc/rtc-isl1208.c: call rtc_update_irq() from the alarm irq handler
samples/seccomp: be less stupid about cross compiling
checkpatch: fix $Float creation of match variables
memcg: fix typo in kmemcg cache walk macro
mm: fix wrong comments about anon_vma lock
MAINTAINERS: update avr32 web ressources
mm/hugetlb: set PTE as huge in hugetlb_change_protection and remove_migration_pte
drivers/rtc/rtc-vt8500.c: fix year field in vt8500_rtc_set_time()
tools/vm: add .gitignore to ignore built binaries
thp: avoid dumping huge zero page
nilfs2: fix fix very long mount time issue
Haojian Zhuang [Mon, 4 Feb 2013 22:28:54 +0000 (14:28 -0800)]
drivers/rtc/rtc-pl031.c: fix the missing operation on enable
The RTC control register should be enabled in the process of
initializing.
Without this patch, I failed to enable RTC in Hisilicon Hi3620 SoC. The
register mapping section in RTC is always read as zero. So I doubt that
ST guys may already enable this register in bootloader. So they won't
meet this issue.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Luebbe [Mon, 4 Feb 2013 22:28:53 +0000 (14:28 -0800)]
drivers/rtc/rtc-isl1208.c: call rtc_update_irq() from the alarm irq handler
Previously the alarm event was not propagated into the RTC subsystem.
By adding a call to rtc_update_irq, this fixes a timeout problem with
the hwclock utility.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Mon, 4 Feb 2013 22:28:52 +0000 (14:28 -0800)]
samples/seccomp: be less stupid about cross compiling
The seccomp filters are currently built for the build host, not for the
machine that they are going to run on, but they are also built for with
the -m32 flag if the kernel is built for a 32 bit machine, both of which
seems rather odd.
It broke allyesconfig on my machine, which is x86-64, but building for
32 bit ARM, with this error message:
In file included from /usr/include/stdio.h:28:0,
from samples/seccomp/bpf-fancy.c:15:
/usr/include/features.h:324:26: fatal error: bits/predefs.h: No such file or directory
because there are no 32 bit libc headers installed on this machine. We
should really be building all the samples for the target machine rather
than the build host, but since the infrastructure for that appears to be
missing right now, let's be a little bit smarter and not pass the '-m32'
flag to the HOSTCC when cross- compiling.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: James Morris <james.l.morris@oracle.com>
Acked-by: Will Drewry <wad@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Mon, 4 Feb 2013 22:28:51 +0000 (14:28 -0800)]
checkpatch: fix $Float creation of match variables
Commit
74349bccedb3 ("checkpatch: add support for floating point
constants") added an unnecessary match variable that caused tests that
used a $Constant or $LvalOrFunc to have one too many matches.
This causes problems with usleep_range, min/max and other extended
tests.
Avoid using match variables in $Float.
Avoid using match variables in $Assignment too.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Glauber Costa [Mon, 4 Feb 2013 22:28:49 +0000 (14:28 -0800)]
memcg: fix typo in kmemcg cache walk macro
The macro for_each_memcg_cache_index contains a silly yet potentially
deadly mistake. Although the macro parameter is _idx, the loop tests
are done over i, not _idx.
This hasn't generated any problems so far, because all users use i as a
loop index. However, while playing with an extension of the code I
ended using another loop index and the compiler was quick to complain.
Unfortunately, this is not the kind of thing that testing reveals =(
Signed-off-by: Glauber Costa <glommer@parallels.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yuanhan Liu [Mon, 4 Feb 2013 22:28:48 +0000 (14:28 -0800)]
mm: fix wrong comments about anon_vma lock
We use rwsem since commit
5a505085f043 ("mm/rmap: Convert the struct
anon_vma::mutex to an rwsem"). And most of comments are converted to
the new rwsem lock; while just 2 more missed from:
$ git grep 'anon_vma->mutex'
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthias Brugger [Mon, 4 Feb 2013 22:28:47 +0000 (14:28 -0800)]
MAINTAINERS: update avr32 web ressources
Web resource http://avr32linux.org/ is no longer available. We add the
mirror of the web page foud at http://mirror.egtvedt.no/avr32linux.org/.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tony Lu [Mon, 4 Feb 2013 22:28:46 +0000 (14:28 -0800)]
mm/hugetlb: set PTE as huge in hugetlb_change_protection and remove_migration_pte
When setting a huge PTE, besides calling pte_mkhuge(), we also need to
call arch_make_huge_pte(), which we indeed do in make_huge_pte(), but we
forget to do in hugetlb_change_protection() and remove_migration_pte().
Signed-off-by: Zhigang Lu <zlu@tilera.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Hillf Danton <dhillf@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tony Prisk [Mon, 4 Feb 2013 22:28:44 +0000 (14:28 -0800)]
drivers/rtc/rtc-vt8500.c: fix year field in vt8500_rtc_set_time()
The year field is incorrectly masked when setting the date. If the year
is beyond 2099, the year field will be incorrectly updated in hardware.
This patch masks the year field correctly.
Signed-off-by: Edgar Toernig <froese@gmx.de>
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Mon, 4 Feb 2013 22:28:43 +0000 (14:28 -0800)]
tools/vm: add .gitignore to ignore built binaries
There is no .gitignore in tools/vm, so 'git status' always show built
binaries. To ignore this, add .gitignore.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kirill A. Shutemov [Mon, 4 Feb 2013 22:28:42 +0000 (14:28 -0800)]
thp: avoid dumping huge zero page
No reason to preserve the huge zero page in core dumps.
Reported-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vyacheslav Dubeyko [Mon, 4 Feb 2013 22:28:41 +0000 (14:28 -0800)]
nilfs2: fix fix very long mount time issue
There exists a situation when GC can work in background alone without
any other filesystem activity during significant time.
The nilfs_clean_segments() method calls nilfs_segctor_construct() that
updates superblocks in the case of NILFS_SC_SUPER_ROOT and
THE_NILFS_DISCONTINUED flags are set. But when GC is working alone the
nilfs_clean_segments() is called with unset THE_NILFS_DISCONTINUED flag.
As a result, the update of superblocks doesn't occurred all this time
and in the case of SPOR superblocks keep very old values of last super
root placement.
SYMPTOMS:
Trying to mount a NILFS2 volume after SPOR in such environment ends with
very long mounting time (it can achieve about several hours in some
cases).
REPRODUCING PATH:
1. It needs to use external USB HDD, disable automount and doesn't
make any additional filesystem activity on the NILFS2 volume.
2. Generate temporary file with size about 100 - 500 GB (for example,
dd if=/dev/zero of=<file_name> bs=
1073741824 count=200). The size of
file defines duration of GC working.
3. Then it needs to delete file.
4. Start GC manually by means of command "nilfs-clean -p 0". When you
start GC by means of such way then, at the end, superblocks is updated
by once. So, for simulation of SPOR, it needs to wait sometime (15 -
40 minutes) and simply switch off USB HDD manually.
5. Switch on USB HDD again and try to mount NILFS2 volume. As a
result, NILFS2 volume will mount during very long time.
REPRODUCIBILITY: 100%
FIX:
This patch adds checking that superblocks need to update and set
THE_NILFS_DISCONTINUED flag before nilfs_clean_segments() call.
Reported-by: Sergey Alexandrov <splavgm@gmail.com>
Signed-off-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Tested-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Tested-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Teigland [Mon, 4 Feb 2013 21:31:22 +0000 (15:31 -0600)]
dlm: check the write size from user
Return EINVAL from write if the size is larger than
allowed. Do this before allocating kernel memory for
the bogus size, which could lead to OOM.
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Tested-by: Jana Saout <jana@saout.de>
Signed-off-by: David Teigland <teigland@redhat.com>
Linus Torvalds [Mon, 4 Feb 2013 20:59:44 +0000 (07:59 +1100)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Three small fixlets"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel/cacheinfo: Shut up annoying warning
x86, doc: Boot protocol 2.12 is in 3.8
x86-64: Replace left over sti/cli in ia32 audit exit code
Linus Torvalds [Mon, 4 Feb 2013 20:58:24 +0000 (07:58 +1100)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Three small fixlets"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/debug: Fix format string for 32-bit platforms
sched: Fix warning in kernel/sched/fair.c
sched/rt: Use root_domain of rt_rq not current processor
Linus Torvalds [Mon, 4 Feb 2013 20:57:09 +0000 (07:57 +1100)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Three fixlets and two small (and low risk) hw-enablement changes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix event group context move
x86/perf: Add IvyBridge EP support
perf/x86: Fix P6 driver section warning
arch/x86/tools/insn_sanity.c: Identify source of messages
perf/x86: Enable Intel Lincroft/Penwell/Cloverview Atom support
Linus Torvalds [Mon, 4 Feb 2013 20:56:07 +0000 (07:56 +1100)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull two small RCU fixlets from Ingo Molnar.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Make rcu_nocb_poll an early_param instead of module_param
rcu: Prevent soft-lockup complaints about no-CBs CPUs
Linus Torvalds [Mon, 4 Feb 2013 20:54:11 +0000 (07:54 +1100)]
Merge tag 'for-linus-
20130204' of git://git.infradead.org/linux-mtd
Pull MTD fixes from David Woodhouse:
"A small set of simple regression and build fixes for 3.8:
- Fix a warning introduced in ONFI NAND probe
- Fix commandline partition parsing
- Require BITREVERSE for DiskOnChip G3 driver
- Fix build failure for davinci_nand as module
- Bump NFLASH_READY_RETRIES for bcm47xxnflash"
* tag 'for-linus-
20130204' of git://git.infradead.org/linux-mtd:
mtd: nand: onfi don't WARN if we are in 16 bits mode
mtd: physmap_of: fix cmdline partition method w/o linux, mtd-name
mtd: docg3 fix missing bitreverse lib
mtd: davinci_nand: fix modular build with CONFIG_OF=y
mtd: bcm47xxnflash: increase NFLASH_READY_RETRIES
fangxiaozhi [Mon, 4 Feb 2013 07:16:34 +0000 (15:16 +0800)]
USB: storage: optimize to match the Huawei USB storage devices and support new switch command
1. Optimize the match rules with new macro for Huawei USB storage devices,
to avoid to load USB storage driver for the modem interface
with Huawei devices.
2. Add to support new switch command for new Huawei USB dongles.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fangxiaozhi [Mon, 4 Feb 2013 07:14:46 +0000 (15:14 +0800)]
USB: storage: Define a new macro for USB storage match rules
1. Define a new macro for USB storage match rules:
matching with Vendor ID and interface descriptors.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Borislav Petkov [Mon, 4 Feb 2013 09:13:15 +0000 (10:13 +0100)]
x86/intel/cacheinfo: Shut up annoying warning
I've been getting the following warning when doing randbuilds
since forever. Now it finally pissed me off just the perfect
amount so that I can fix it.
arch/x86/kernel/cpu/intel_cacheinfo.c:489:27: warning: ‘cache_disable_0’ defined but not used [-Wunused-variable]
arch/x86/kernel/cpu/intel_cacheinfo.c:491:27: warning: ‘cache_disable_1’ defined but not used [-Wunused-variable] arch/x86/kernel/cpu/intel_cacheinfo.c:524:27: warning: ‘subcaches’ defined but not used [-Wunused-variable]
It happens because in randconfigs where CONFIG_SYSFS is not set,
the whole sysfs-interface to L3 cache index disabling is
remaining unused and gcc correctly warns about it. Make it
optional, depending on CONFIG_SYSFS too, as is the case with
other sysfs-related machinery in this file.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Link: http://lkml.kernel.org/r/1359969195-27362-1-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Mon, 4 Feb 2013 05:58:41 +0000 (16:58 +1100)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
Pull powerpc update from Benjamin Herrenschmidt:
"Just so that you don't get too bored on your Island here's a patch for
3.8 fixing a nasty bug that affects the new 64T support that was
merged in 3.7. Please apply whenever you have a chance (and an
internet connection!)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix hash computation function
Linus Torvalds [Mon, 4 Feb 2013 05:51:53 +0000 (16:51 +1100)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull radeon fixes from Dave Airlie:
"I got these late last week, the main chunks of these fix a rendering
regression since 3.7, and the settle ones all fix the issue where we
don't wait long enough for the memory controller to settle after
turning it off which causes bad memory reads, they all fix real users
bugs, and most of them are destined for stable.
Can't remember if you had net connection on that island :-)"
I don't know if the "two tin-cans and a string" thing here on "that
island" can really be considered internet, but I guess I can pull
things. Barely.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: switch back to the CP ring for VM PT updates
drm/radeon: prevent crash in the ring space allocation
drm/radeon: Calling object_unrefer() when creating fb failure
drm/radeon/r5xx-r7xx: wait for the MC to settle after MC blackout
drm/radeon/evergreen+: wait for the MC to settle after MC blackout
drm/radeon: protect against div by 0 in backend setup
drm/radeon: fix backend map setup on 1 RB sumo boards
drm/radeon: add quirk for RV100 board
drm/radeon: add WAIT_UNTIL to the non-VM safe regs list for cayman/TN
drm/radeon: fix MC blackout on evergreen+
Aneesh Kumar K.V [Tue, 29 Jan 2013 19:40:42 +0000 (19:40 +0000)]
powerpc/mm: Fix hash computation function
The ASM version of hash computation function was truncating the upper bit.
Make the ASM version similar to hpt_hash function. Remove masking vsid bits.
Without this patch, we observed hang during bootup due to not satisfying page
fault request correctly. The fault handler used wrong hash values to update
the HPTE. Hence we kept looping with page fault.
hash_page(ea=
000001003e260008, access=203, trap=300 ip=
3fff91787134 dsisr
42000000
The computed value of hash
000000000f22f390
update: avpnv=
4003e46054003e00, hash=
000000000722f390, f=
80000006, psize: 2 ...
BenH: The over-masking has been there for ever but only hurts with the
new 64T support introduced in 3.7
Reported-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Tested-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.7]
Jiri Olsa [Fri, 1 Feb 2013 10:23:45 +0000 (11:23 +0100)]
perf: Fix event group context move
When we have group with mixed events (hw/sw) we want to end up
with group leader being in hw context. So if group leader is
initialy sw event, we move all the events under hw context.
The move is done for each event by removing it from its context
and adding it back into proper one. As a part of the removal the
event is automatically disabled, which is not what we want at
this stage of creating groups.
The fix is to initialize event state after removal from sw
context.
This fix resulted from the following discussion:
http://thread.gmane.org/gmane.linux.kernel.perf.user/1144
Reported-by: Andreas Hollmann <hollmann@in.tum.de>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Vince Weaver <vince@deater.net>
Link: http://lkml.kernel.org/r/1359714225-4231-1-git-send-email-jolsa@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Petr Kubánek [Fri, 1 Feb 2013 16:24:04 +0000 (17:24 +0100)]
USB: ftdi_sio: add Zolix FTDI PID
Add support for Zolix Omni 1509 monochromator custom USB-RS232 converter.
Signed-off-by: Petr Kubánek <petr@kubanek.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Fri, 1 Feb 2013 11:06:51 +0000 (12:06 +0100)]
USB: option: add Changhong CH690
New device with 3 serial interfaces:
If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend) Sub=ff Prot=ff
If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend) Sub=ff Prot=ff
If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend) Sub=ff Prot=ff
If#= 3 Alt= 0 #EPs= 2 Cls=08(stor) Sub=06 Prot=50
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sven Killig [Fri, 1 Feb 2013 22:43:06 +0000 (23:43 +0100)]
USB: ftdi_sio: add PID/VID entries for ELV WS 300 PC II
Add PID/VID entries for ELV WS 300 PC II weather station
Signed-off-by: Sven Killig <sven@killig.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sat, 2 Feb 2013 02:37:56 +0000 (13:37 +1100)]
Merge git://git./linux/kernel/git/nab/target-pending
Pull scsi target fixes from Nicholas Bellinger:
"Here's the current set of v3.8-rc fixes in the target-pending.git
queue. Apologies in advance for these missing the -rc6 release, and
having to be destined for -rc7 code.
The majority of these patches are regression bugfixes specific to
v3.8-rc code changes, namely the zero-length CDB handling breakage
after the sense_reason_t conversion, and preventing configfs port
linking for unconfigured devices after the recent struct
se_subsystem_dev removal. These is also one (the divide by zero bug
for unconfigured devices) that is CC'ed to stable."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix divide by zero bug in fabric_max_sectors for unconfigured devices
target: Fix regression allowing unconfigured devices to fabric port link
tcm_vhost: fix pr_err on early kick
target: Fix zero-length READ_CAPACITY_16 regression
target: Fix zero-length MODE_SENSE regression
target: Fix zero-length INQUIRY additional sense code regression
Alex Deucher [Thu, 26 Jul 2012 22:48:01 +0000 (18:48 -0400)]
drm/radeon: add Oland pci ids
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Thu, 30 Aug 2012 18:00:03 +0000 (14:00 -0400)]
drm/radeon: radeon-asic updates for Oland
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Thu, 26 Jul 2012 22:36:28 +0000 (18:36 -0400)]
drm/radeon: add ucode loading support for Oland
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Thu, 26 Jul 2012 21:42:25 +0000 (17:42 -0400)]
drm/radeon: fill in gpu init for Oland
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Tue, 18 Dec 2012 22:01:35 +0000 (17:01 -0500)]
drm/radeon: add Oland chip family
Oland is a new asic in the SI family.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Thu, 31 Jan 2013 21:26:02 +0000 (16:26 -0500)]
drm/radeon: switch back to using the DMA ring for VM PT updates
Now that we have switched to using IBs for page table updates,
we can switch back the using the DMA ring.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Fri, 1 Feb 2013 16:32:42 +0000 (17:32 +0100)]
drm/radeon: use IBs for VM page table updates v2
For very large page table updates, we can exceed the
size of the ring. To avoid this, use an IB to perform
the page table update.
v2(ck): cleanup the IB infrastructure and the use it instead
of filling the struct ourself.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Yasuaki Ishimatsu [Fri, 1 Feb 2013 01:14:20 +0000 (10:14 +0900)]
GPU/i915: Fix acpi_bus_get_device() check in drivers/gpu/drm/i915/intel_opregion.c
acpi_bus_get_device() returns int not acpi_status.
The patch change not to apply ACPI_FAILURE() to the return value of
acpi_bus_get_device().
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
YOSHIFUJI Hideaki [Fri, 25 Jan 2013 14:54:20 +0000 (16:54 +0200)]
digsig: Fix memory leakage in digsig_verify_rsa()
digsig_verify_rsa() does not free kmalloc'ed buffer returned by
mpi_get_buffer().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Morris <james.l.morris@oracle.com>
H. Peter Anvin [Fri, 1 Feb 2013 04:23:49 +0000 (20:23 -0800)]
x86, doc: Boot protocol 2.12 is in 3.8
The boot protocol 2.12 changes were pulled for 3.8, so update the
documentation accordingly.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
H. Peter Anvin [Fri, 1 Feb 2013 04:22:57 +0000 (20:22 -0800)]
Merge tag 'v3.8-rc6' into x86/urgent
Linux 3.8-rc6
Merged in order to add a documentation update versus new code in
upstream.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Linus Torvalds [Fri, 1 Feb 2013 01:08:14 +0000 (12:08 +1100)]
Linux 3.8-rc6
Linus Torvalds [Fri, 1 Feb 2013 01:04:22 +0000 (12:04 +1100)]
Merge tag 'dm-3.8-fixes-2' of git://git./linux/kernel/git/agk/linux-dm
Pull more device-mapper fixes from Alasdair G Kergon:
"A fix for stacked dm thin devices and a fix for the new dm WRITE SAME
support."
* tag 'dm-3.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm: fix write same requests counting
dm thin: fix queue limits stacking
Dave Airlie [Thu, 31 Jan 2013 23:51:02 +0000 (10:51 +1100)]
Merge branch 'drm-fixes-3.8' of git://people.freedesktop.org/~agd5f/linux
Alex writes:
"A few more radeon fixes for 3.8. Mostly small stuff. The big
change is disabling the use of the DMA ring for VM PT updates. This
reverts back to the 3.7 behavior. Problem is we can get huge PT
updates in certain cases that are too big for the DMA ring. I've
got patches to use an IB for this so I can re-enable the use of the
DMA ring for VM PT updates in 3.9. This request also includes the
patches from the last pull request I sent on Monday in case you haven't
pulled them yet."
* 'drm-fixes-3.8' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: switch back to the CP ring for VM PT updates
drm/radeon: prevent crash in the ring space allocation
drm/radeon: Calling object_unrefer() when creating fb failure
drm/radeon/r5xx-r7xx: wait for the MC to settle after MC blackout
drm/radeon/evergreen+: wait for the MC to settle after MC blackout
drm/radeon: protect against div by 0 in backend setup
drm/radeon: fix backend map setup on 1 RB sumo boards
drm/radeon: add quirk for RV100 board
drm/radeon: add WAIT_UNTIL to the non-VM safe regs list for cayman/TN
drm/radeon: fix MC blackout on evergreen+
Nicholas Bellinger [Thu, 31 Jan 2013 23:05:48 +0000 (15:05 -0800)]
target: Fix divide by zero bug in fabric_max_sectors for unconfigured devices
This patch fixes a possible divide by zero bug when the fabric_max_sectors
device attribute is written and backend se_device failed to be successfully
configured -> enabled.
Go ahead and use block_size=512 within se_dev_set_fabric_max_sectors()
in the event of a target_configure_device() failure case, as no valid
dev->dev_attrib.block_size value will have been setup yet.
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nicholas Bellinger [Thu, 31 Jan 2013 22:56:12 +0000 (14:56 -0800)]
target: Fix regression allowing unconfigured devices to fabric port link
This patch fixes a v3.8-rc1 regression bug where an unconfigured se_device
was incorrectly allowed to perform a fabric port-link. This bug was
introduced in commit:
commit
0fd97ccf45be26fb01b3a412f1f6c6b5044b2f16
Author: Christoph Hellwig <hch@infradead.org>
Date: Mon Oct 8 00:03:19 2012 -0400
target: kill struct se_subsystem_dev
which ended up dropping the original se_subsystem_dev->se_dev_ptr check
preventing this from happening with pre commit
0fd97ccf code.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Linus Torvalds [Thu, 31 Jan 2013 21:44:59 +0000 (08:44 +1100)]
Merge branch 'for-3.8/upstream-fixes' of git://git./linux/kernel/git/jikos/hid
PullHID fixes from Jiri Kosina:
- fix i2c-hid and hidraw interaction, by Benjamin Tissoires
- a quirk to make a particular device (Formosa IR receiver) work
properly, by Nicholas Santos
* 'for-3.8/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: i2c-hid: fix i2c_hid_output_raw_report
HID: usbhid: quirk for Formosa IR receiver
HID: remove x bit from sensor doc
Linus Torvalds [Thu, 31 Jan 2013 21:43:52 +0000 (08:43 +1100)]
Merge tag 'nfs-for-3.8-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Error reporting in nfs_xdev_mount incorrectly maps all errors to
ENOMEM
- Fix an NFSv4 refcounting issue
- Fix a mount failure when the server reboots during NFSv4 trunking
discovery
- NFSv4.1 mounts may need to run the lease recovery thread.
- Don't silently fail setattr() requests on mountpoints
- Fix a SUNRPC socket/transport livelock and priority queue issue
- We must handle NFS4ERR_DELAY when resetting the NFSv4.1 session.
* tag 'nfs-for-3.8-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4.1: Handle NFS4ERR_DELAY when resetting the NFSv4.1 session
SUNRPC: When changing the queue priority, ensure that we change the owner
NFS: Don't silently fail setattr() requests on mountpoints
NFSv4.1: Ensure that nfs41_walk_client_list() does start lease recovery
NFSv4: Fix NFSv4 trunking discovery
NFSv4: Fix NFSv4 reference counting for trunked sessions
NFS: Fix error reporting in nfs_xdev_mount
Linus Torvalds [Thu, 31 Jan 2013 21:43:04 +0000 (08:43 +1100)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"A number of fixes all across the MIPS tree. No area is particularly
standing out and things have cooled down quite nicely for a release."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Function tracer: Fix broken function tracing
mips: Move __virt_addr_valid() to a place for MIPS 64
MIPS: Netlogic: Fix UP compilation on XLR
MIPS: AR71xx: Fix AR71XX_PCI_MEM_SIZE
MIPS: AR724x: Fix AR724X_PCI_MEM_SIZE
MIPS: Lantiq: Fix cp0_perfcount_irq mapping
MIPS: DSP: Fix DSP mask for registers.
MIPS: Fix build failure by adding definition of pfn_pmd().
MIPS: Octeon: Fix warning.
MIPS: delay.c: Check BITS_PER_LONG instead of __SIZEOF_LONG__
MIPS: PNX833x: Fix comment.
MIPS: Add struct p_format to union mips_instruction.
MIPS: Export <asm/break.h>.
MIPS: BCM47xx: Enable SSB prerequisite SSB_DRIVER_PCICORE.
MIPS: BCM47xx: Select GPIOLIB for BCMA on bcm47xx platform
MIPS: vpe.c: Fix null pointer dereference in print arguments.
Alex Deucher [Thu, 24 Jan 2013 20:00:17 +0000 (15:00 -0500)]
drm/radeon: don't reset the MC on IGPs/APUs
The MC isn't part of the GPU per se.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Thu, 24 Jan 2013 16:37:19 +0000 (11:37 -0500)]
drm/radeon: use the reset mask to determine if rings are hung
fetch the reset mask and check if the relevant ring flags
are set to determine whether the ring is hung or not.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>