drm/lima: add missing Kconfig dependency

Current implementation does not support MMU-less
plarforms.

Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Fixes: a1d2a6339961 ("drm/lima: driver for ARM Mali4xx GPUs")
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190409003617.4470-1-yuq825@gmail.com

drm/meson: Add G12A support for the DW-HDMI Glue

The Amlogic G12A embeds the same Synopsys DW-HDMI Controller,
but with :
- a "backport" of the HDR signaling registers from more recent
  DW-HDMI controllers, this will need a tweak since it's not
  normally present on this version of the DW-HDMI controller
- A direct mapping of TOP and DW-HDMI registers instead of an
  internal bus accessed using read/write registers
- Support for RX-SENSE, but not yet implemented
- Support for HDMI 2.1 Dynamic HDR, but not yet implemented
- Different registers mapping for the HDMI PHY setup

This patchs adds support for these changes while providing exact
same support as the previous GXBB, GXL & GXM SoCs.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-12-narmstrong@baylibre.com

drm/meson: Add G12A compatible

Finally add the Amlogic G12A SoC compatible for the VPU driver.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-11-narmstrong@baylibre.com

drm/meson: Add G12A Video Clock setup

While switching to the Common Clock Framework is still Work In Progress,
this patch adds the corresponding G12A HDMI PLL setup to be on-par
with the other SoCs support.

The G12A has only a single tweak about the high frequency setup,
where the HDMI PLL needs a specific setup to handle correctly the
5.94GHz DCO frequency.

Apart that, it handls ecorrectly all the other HDMI frequencies
and can achieve even better DMT clock frequency precision with
the larger fractional dividier width.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-10-narmstrong@baylibre.com

drm/meson: Add G12A support for CVBS Encoder

The Meson G12A SoCs uses the exact same CVBS encoder except a simple
CVBS DAC register offset and settings delta.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fixed subject typo]
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-9-narmstrong@baylibre.com

drm/meson: Add G12A support for plane handling in CRTC driver

This patch adds support for the new OSD+VD Plane blending module
in the CRTC code by adding the G12A code to manage the blending
module and setting the right OSD1 & VD1 plane registers.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-8-narmstrong@baylibre.com

drm/meson: Add G12A Support for the Overlay video plane

Amlogic G12A SoC supports the same set of Video Planes, but now
are handled by the new OSD plane blender module.

This patch uses the same VD1 plane for G12A, using the exact same scaler
and VD1 setup registers, except using the new blender register to
disable the plane.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fix typo in commit log]
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-7-narmstrong@baylibre.com

drm/meson: Add G12A support for OSD1 Plane

Amlogic G12A SoC supports now up to 3 OSD planes (1 more than the
previous SoCs) and a brand new OSD plane blender module.

This patch uses the same OSD1 plane for G12A, using the exact same scaler
and OSD1 setup registers, except using the new blender register to
disable the plane.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fixed typo in commit log]
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-6-narmstrong@baylibre.com

drm/meson: Add G12A Support for VIU setup

Amlogic G12A SoC needs a different VIU setup code,
handle it.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-5-narmstrong@baylibre.com

drm/meson: Add G12A Support for VPP setup

Amlogic G12A needs a different VPP setup code, handle it here.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-4-narmstrong@baylibre.com

drm/meson: Add registers for G12A SoC

This patch adds the new VPU registers added since the
Amlogic GXM SoCs.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-3-narmstrong@baylibre.com

drm/meson: Switch PLL to 5.94GHz base for 297Mhz pixel clock

On Amlogic G12A SoC, the 2,97GHz PLL frequency is not stable enough
to provide a correct 297MHz pixel clock, so switch the PLL base
frequency with a /2 OD when the 297MHz pixel clock is requested.

This solves the issue on G12A and also works fine on GXBB, GXL & GXM.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-2-narmstrong@baylibre.com

dt-bindings: display: amlogic, meson-dw-hdmi: Add G12A compatible and ports

The Amlogic G12A SoC has a slighly modified DW-HDMI Glue with
support for HDMI 2.1 and a different DW-HDMI register access.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190313141030.5958-3-narmstrong@baylibre.com

dt-bindings: display: amlogic, meson-vpu: Add G12A compatible and ports

The Amlogic G12A VPU is very similar to the Amlogic GXM VPU but with :
- an enhanced plane blender, with up to 3 OSD planes
- support for AFBC 1.2 decoder (for Bifrost GPU)
- support display mode up to 4k60@75Hz

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190313141030.5958-2-narmstrong@baylibre.com

dt-bindings: gpu: add bindings for the ARM Mali Bifrost GPU

Add the bindings for the Bifrost family of ARM Mali GPUs.

The Bifrost GPU architecture is similar to the Midgard family,
but with a different Shader Core & Execution Engine structures.

Bindings are based on the Midgard family bindings, but the inner
architectural changes makes it a separate family needing separate
bindings.

The Bifrost GPUs are present in a number of recent SoCs, like the
Amlogic G12A Family, and many other vendors.
The Amlogic vendor specific compatible is added to handle the
specific IP integration differences and dependencies.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[narmstrong: fixed small typo in compatible description]
Link: https://patchwork.freedesktop.org/patch/msgid/20190401080949.14550-1-narmstrong@baylibre.com

MAINTAINERS: mark lima mailing list as moderated

Note that the lima mailing list is moderated.

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Qiang Yu <yuq825@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: lima@lists.freedesktop.org
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9138d8e8-5390-0650-9bc3-050b869e978c@infradead.org
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>

drm/cirrus: rewrite and modernize driver.

Time to kill some bad sample code people are copying from ;)

This is a complete rewrite of the cirrus driver.  The cirrus_mode_set()
function is pretty much the only function which is carried over largely
unmodified.  Everything else is upside down.

It is a single monster patch.  But given that it does some pretty
fundamental changes to the drivers workflow and also reduces the code
size by roughly 70% I think it'll still be alot easier to review than a
longish baby-step patch series.

Changes summary:
 - Given the small amout of video memory (4 MB) the cirrus device has
   the rewritten driver doesn't try to manage buffers there.  Instead
   it will blit (memcpy) the active framebuffer to video memory.
 - All gem objects are stored in main memory and are manged using the
   new shmem helpers.  ttm is out.
 - It supports RG16, RG24 and XR24 formats.  XR24 gets converted to RG24
   or RG16 at blit time if needed, to avoid the pitch becoming larger
   than what the cirrus hardware can handle.
 - The simple display pipeline is used.
 - The generic fbdev emulation is used.
 - It's a atomic driver now.
 - It runs wayland.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20190405095219.9231-6-kraxel@redhat.com

drm: add drm_fb_xrgb8888_to_rgb888_dstclip()

Simliar to drm_fb_xrgb8888_to_rgb565_dstclip() but converts to rgb888
instead of rgb565.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20190405095219.9231-5-kraxel@redhat.com

drm: add drm_fb_xrgb8888_to_rgb565_dstclip()

It is a drm_fb_xrgb8888_to_rgb565() variant which checks the clip
rectangle for the destination too.

Common code between drm_fb_xrgb8888_to_rgb565() and
drm_fb_xrgb8888_to_rgb565_dstclip() was factored out into the
drm_fb_xrgb8888_to_rgb565_lines() helper function.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20190405095219.9231-4-kraxel@redhat.com

drm: add drm_fb_memcpy_dstclip() helper

It is a drm_fb_memcpy() variant which checks the clip rectangle for the
destination too.

Common code between drm_fb_memcpy() and drm_fb_memcpy_dstclip() was
factored out into the drm_fb_memcpy_lines() helper function.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20190405095219.9231-3-kraxel@redhat.com

drm: move tinydrm format conversion helpers to new drm_format_helper.c

Also rename them from tinydrm_* to drm_fb_*
Pure code motion, no functional change.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20190405095219.9231-2-kraxel@redhat.com

Documentation/gpu/meson: Remove link to meson_canvas.c

The file was removed in the below patch and is causing this error:
WARNING: kernel-doc '../scripts/kernel-doc -rst -enable-lineno -function Canvas ../drivers/gpu/drm/meson/meson_canvas.c' failed with return code

Fixes: 2bf6b5b0e374 ("drm/meson: exclusively use the canvas provider module")
Cc: Maxime Jourdan <mjourdan@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190403205652.183496-1-sean@poorly.run

drm/pl111: fix possible object reference leak

The call to of_find_matching_node_and_match returns a node pointer with
refcount incremented thus it must be explicitly decremented after the
last usage.

Detected by coccinelle with the following warnings:
drivers/gpu/drm/pl111/pl111_versatile.c:333:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
drivers/gpu/drm/pl111/pl111_versatile.c:340:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
drivers/gpu/drm/pl111/pl111_versatile.c:346:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
drivers/gpu/drm/pl111/pl111_versatile.c:354:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
drivers/gpu/drm/pl111/pl111_versatile.c:395:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
drivers/gpu/drm/pl111/pl111_versatile.c:402:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.

Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Eric Anholt <eric@anholt.net> (supporter:DRM DRIVER FOR ARM PL111 CLCD)
Cc: David Airlie <airlied@linux.ie> (maintainer:DRM DRIVERS)
Cc: Daniel Vetter <daniel@ffwll.ch> (maintainer:DRM DRIVERS)
Cc: dri-devel@lists.freedesktop.org (open list:DRM DRIVERS)
Cc: linux-kernel@vger.kernel.org (open list)
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/1554307455-40361-6-git-send-email-wen.yang99@zte.com.cn

drm/vc4: vc4_debugfs_regset32() can be static

Fixes: c9be804c8c7a ("drm/vc4: Use common helpers for debugfs setup by the driver components.")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190403213629.GA31570@lkp-ib03

drm/panel: Rocktech jh057n00900: Add terminating newlines to logging

These were missing '\n' terminations, add them.

Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/da6f2344396555034cf2476c8338b0ce1c56e0a7.camel@perches.com

MAINTAINERS: Add ASPEED BMC GFX DRM driver entry

This hardware is found inside ASPEED Baseboard Management Controller
(BMC) system on chips. It is called the 'SOC Display Controller' or 'GFX'.

Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://patchwork.freedesktop.org/patch/msgid/20190403001909.31637-4-joel@jms.id.au

drm: Add ASPEED GFX driver

This driver is for the ASPEED BMC SoC's GFX display hardware. This
driver runs on the ARM based BMC systems, unlike the ast driver which
runs on a host CPU and is is for a PCI graphics device.

Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190403001909.31637-3-joel@jms.id.au

dt-bindings: gpu: Add ASPEED GFX bindings document

This describes the ASPEED BMC SoC's display controller.

Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://patchwork.freedesktop.org/patch/msgid/20190403001909.31637-2-joel@jms.id.au

drm/vc4: Disable V3D interactions if the v3d component didn't probe.

One might want to use the VC4 display stack without using Mesa.
Similar to the debugfs fixes for not having all of the possible
display bits enabled, make sure you can't oops in vc4 if v3d isn't
enabled.

v2: Fix matching against other v3d variants (review by Paul), don't
    forget to set irq_enabled so that the vblank uapi works
v3: Use -ENODEV instead of -EINVAL on Paul's suggestion.

Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190401183559.3823-2-eric@anholt.net
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>

drm/vc4: Use common helpers for debugfs setup by the driver components.

The global list of all debugfs entries for the driver was painful: the
list couldn't see into the components' structs, so each component had
its own debugs show function to find the component, then find the
regset and dump it.  The components also had to be careful to check
that they were actually registered in vc4 before dereferencing
themselves, in case they weren't probed on a particular platform.
They routinely failed at that.

Instead, we can have the components add their debugfs callbacks to a
little list in vc4 to be registered at drm_dev_register() time, which
gets vc4_debugfs.c out of the business of knowing the whole list of
components.

Thanks to this change, dsi0 (if it existed) would register its node.

v2: Rebase on hvs_underrun addition.
v3: whitespace fixup

Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190401183559.3823-1-eric@anholt.net
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>

drm/panel: otm8009a: Set clock to 29.70 Mhz

The panel does not support clock frequency over 30.74 MHz. The clock
rate has been reduced to 29.70 MHz & new timings have been computed to
get a framerate of 50 fps.

Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1553155646-13636-1-git-send-email-yannick.fertre@st.com

drm/panel: rm68200: No error msg if probe deferred

Do not print an error message if the regulator framework returns
EPROBE_DEFER.

Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1553155535-13555-1-git-send-email-yannick.fertre@st.com

drm/panel: otm8009a: No error msg if probe deferred

Do not print an error message if the regulator framework returns
EPROBE_DEFER.

Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1553155484-13460-1-git-send-email-yannick.fertre@st.com

drm/panel: otm8009a: Add delay at the end of initialization

At the end of initialization, a delay is required by the panel. Without
this delay, the panel could received a frame early & generate a crash of
panel (black screen).

Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1553155445-13407-1-git-send-email-yannick.fertre@st.com

drm/panel: Add Rocktech jh057n00900 panel driver

Support Rocktech jh057n00900 5.5" 720x1440 TFT LCD panel. It is a MIPI
DSI video mode panel.

The panel seems to use a Sitronix ST7703 look alike (most of the
commands look similar to the ST7703's data sheet but use a different
number of parameters). The initial version of the DSI init sequence
(including sleeps) were provided by the vendor. Sleeps were reduced
considerably though to speed up initialization.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1a9ce687be283c66dfb26d1dfb52a7bf695090fa.1554114302.git.agx@sigxcpu.org

dt-bindings: Add Rocktech jh057n00900 panel bindings

The Rocktec jh057n00900 is a 5.5" MIPI DSI video mode panel with a
720x1440 resolution and a built in backlight.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ec59b22907ac28764ffb3bec33445b6e019945a4.1554114302.git.agx@sigxcpu.org

dt-bindings: Add vendor prefix for ROCKTECH DISPLAYS LIMITED

Add ROCKTECH DISPLAYS LIMITED (https://rocktech.com.hk) LCD panel
supplier.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b8db03faa344c834e6cc81eef1eca154e1a1bd90.1554114302.git.agx@sigxcpu.org

dt-bindings: display/panel: Add missing unit names

Some examples were missing the unit names triggering

 Warning (unit_address_vs_reg): .../panel: node has a reg or ranges property, but no unit name

warnings when used verbatim in DTs and running dtc with W=1.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/901e836ea06889a9d91a799102b2a6b836d93dcd.1553529797.git.agx@sigxcpu.org

drm/panel: Add Feiyang FY07024DI26A30-D MIPI-DSI LCD panel

Feiyang FY07024DI26A30-D is 1024x600, 4-lane MIPI-DSI LCD panel.

Add panel driver for it.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Bhushan Shah <bshah@kde.org>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190212204109.3528-2-jagan@amarulasolutions.com

dt-bindings: panel: Add Feiyang FY07024DI26A30-D MIPI-DSI LCD panel

Feiyang FY07024DI26A30-D is 1024x600, 4-lane MIPI-DSI LCD panel.

Add dt-bingings for it.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190212204109.3528-1-jagan@amarulasolutions.com

drm/gamma: Clarify gamma lut uapi

Interpreting it as a 0.16 fixed point means we can't accurately
represent 1.0. Which is one of the values we really should be able to
represent.

Since most (all?) luts have lower precision this will only affect
rounding of 0xffff.

Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: "Kumar, Kiran S" <kiran.s.kumar@intel.com>
Cc: Kausal Malladi <kausalmalladi@gmail.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Rob Bradford <robert.bradford@intel.com>
Cc: Daniel Stone <daniels@collabora.com>
Cc: Stefan Schake <stschake@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: James (Qian) Wang <james.qian.wang@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190329092027.3430-1-daniel.vetter@ffwll.ch

drm/fb-helper: generic: Call drm_client_add() after setup is done

Hotplug can happen while drm_fbdev_generic_setup() is running so move
drm_client_add() call after setup is done to avoid
drm_fbdev_client_hotplug() running in two threads at the same time.

Fixes: 9060d7f49376 ("drm/fb-helper: Finish the generic fbdev emulation")
Cc: stable@vger.kernel.org
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190401141358.25309-1-noralf@tronnes.org

drm/vc4: Call drm_dev_register() after all setup is done

drm_dev_register() initializes internal clients like bootsplash as the
last thing it does, so all setup needs to be done at this point.

Fix by calling vc4_kms_load() before registering.
Also check the error code returned from that function.

Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326175546.18126-17-noralf@tronnes.org

drm/fb-helper: dpms_legacy(): Only set on connectors in use

For each enabled crtc the functions sets dpms on all registered connectors.
Limit this to only doing it once and on the connectors actually in use.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Fixes: 023eb571a1d0 ("drm: correctly update connector DPMS status in drm_fb_helper")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326175546.18126-3-noralf@tronnes.org

drm/fb-helper: Remove unused gamma_size variable

The gamma_size variable has not been used since
commit 4abe35204af8 ("drm/kms/fb: use slow work mechanism for normal hotplug also.")

While in the area move a comment back to its code block.
They got separated by
commit d50ba256b5f1 ("drm/kms: start adding command line interface using fb.").

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326175546.18126-2-noralf@tronnes.org

drm/cirrus: drop mode_info.mode_config_initialized

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20190402090459.12126-3-kraxel@redhat.com

drm/bochs: drop mode_config_initialized

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20190402090459.12126-2-kraxel@redhat.com

drm/cirrus: add missing drm_helper_force_disable_all() call.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20190401140306.28063-4-kraxel@redhat.com

drm/bochs: add missing drm_atomic_helper_shutdown() call.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20190401140306.28063-3-kraxel@redhat.com

drm/virtio: add missing drm_atomic_helper_shutdown() call.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20190401140306.28063-2-kraxel@redhat.com

drm/v3d: fix a missing check of pm_runtime_get_sync

pm_runtime_get_sync could fail and thus deserves a check.

The patch adds such a check and return its error code upstream
if it indeed failed.

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190324231602.2436-1-kjlu@umn.edu
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>

MAINTAINERS: add drm/lima driver info

Signed-off-by: Qiang Yu <yuq825@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190329134748.8269-1-yuq825@gmail.com
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/lima: driver for ARM Mali4xx GPUs

- Mali 4xx GPUs have two kinds of processors GP and PP. GP is for
  OpenGL vertex shader processing and PP is for fragment shader
  processing. Each processor has its own MMU so prcessors work in
  virtual address space.
- There's only one GP but multiple PP (max 4 for mali 400 and 8
  for mali 450) in the same mali 4xx GPU. All PPs are grouped
  togather to handle a single fragment shader task divided by
  FB output tiled pixels. Mali 400 user space driver is
  responsible for assign target tiled pixels to each PP, but mali
  450 has a HW module called DLBU to dynamically balance each
  PP's load.
- User space driver allocate buffer object and map into GPU
  virtual address space, upload command stream and draw data with
  CPU mmap of the buffer object, then submit task to GP/PP with
  a register frame indicating where is the command stream and misc
  settings.
- There's no command stream validation/relocation due to each user
  process has its own GPU virtual address space. GP/PP's MMU switch
  virtual address space before running two tasks from different
  user process. Error or evil user space code just get MMU fault
  or GP/PP error IRQ, then the HW/SW will be recovered.
- Use GEM+shmem for MM. Currently just alloc and pin memory when
  gem object creation. GPU vm map of the buffer is also done in
  the alloc stage in kernel space. We may delay the memory
  allocation and real GPU vm map to command submission stage in the
  furture as improvement.
- Use drm_sched for GPU task schedule. Each OpenGL context should
  have a lima context object in the kernel to distinguish tasks
  from different user. drm_sched gets task from each lima context
  in a fair way.

mesa driver can be found here before upstreamed:
https://gitlab.freedesktop.org/lima/mesa

v8:
- add comments for in_sync
- fix ctx free miss mutex unlock

v7:
- remove lima_fence_ops with default value
- move fence slab create to device probe
- check pad ioctl args to be zero
- add comments for user/kernel interface

v6:
- fix comments by checkpatch.pl

v5:
- export gp/pp version to userspace
- rebase on drm-misc-next

v4:
- use get param interface to get info
- separate context create/free ioctl
- remove unused max sched task param
- update copyright time
- use xarray instead of idr
- stop using drmP.h

v3:
- fix comments from kbuild robot
- restrict supported arch to tested ones

v2:
- fix syscall argument check
- fix job finish fence leak since kernel 5.0
- use drm syncobj to replace native fence
- move buffer object GPU va map into kernel
- reserve syscall argument space for future info
- remove kernel gem modifier
- switch TTM back to GEM+shmem MM
- use time based io poll
- use whole register name
- adopt gem reservation obj integration
- use drm_timeout_abs_to_jiffies

Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Herring <robh@kernel.org>
Cc: Christian König <ckoenig.leichtzumerken@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Andreas Baierl <ichgeh@imkreisrum.de>
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Rob Herring <robh@kerrnel.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/291200/

drm/vc4: Make sure that the v3d ident debugfs has vc4's power on.

Otherwise, you sometimes decode the ident fields based on 0xdeadbeef
register reads.

Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190220210343.28157-7-eric@anholt.net
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>

drm/vc4: Add helpers for pm get/put.

This makes sure the vc4_reset doesn't hit an obscure race with the
GET_PARAM ioctl, fixes a decrement outside of the lock, and prevents
future code from making mistakes with the weird return value of
pm_runtime_get_sync().

Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190220210343.28157-6-eric@anholt.net
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>

drm/vc4: Use drm_printer for the debugfs and runtime bo stats output.

Now I can extend the stats without more copy and pasting between the
two.

Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190220210343.28157-4-eric@anholt.net
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>

drm: shmem: Off by one in drm_gem_shmem_fault()

The shmem->pages[] array has "num_pages" elements so the > should be >=
to prevent reading beyond the end of the array.  The shmem->pages[]
array is allocated in drm_gem_shmem_prime_import_sg_table().

Fixes: 2194a63a818d ("drm: Add library for shmem backed GEM objects")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322064125.GA12551@kadam

drm/vc4: Use drm_print_regset32() for our debug register dumping.

This removes a bunch of duplicated boilerplate for the debugfs vs
runtime printk debug dumping.

Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190220210343.28157-2-eric@anholt.net
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>

drm: Add a helper function for printing a debugfs_regset32.

The debugfs_regset32 is nice to use for reducing boilerplate in
dumping a bunch of regs in debugfs, but we also want to be able to
print to dmesg them at runtime for driver debugging.  drm_printer lets
us format debugfs and the printk the same way.

v2: Add some kerneldoc for the function (requested by danvet)

Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190220210343.28157-1-eric@anholt.net
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> (v1)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/v3d: Rename the fence signaled from IRQs to "irq_fence".

We have another thing called the "done fence" that tracks when the
scheduler considers the job done, and having the shared name was
confusing.

Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190313235211.28995-2-eric@anholt.net
Reviewed-by: Dave Emett <david.emett@broadcom.com>

drm/v3d: Add a note about OOM vs FLDONE, which may be racing on v3.3.

We deref v3d->bin_job in the work handler, but v3d->bin_job doesn't
actually hold a ref on the job.

v2: typo fix FRDONE -> FLDONE

Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190313235211.28995-1-eric@anholt.net
Reviewed-by: Dave Emett <david.emett@broadcom.com>

drm/v3d: fix a NULL vs error pointer mixup

The drm_gem_shmem_create() returns error pointers and v3d_bo_create() is
also supposed to return error pointers.

Fixes: 40609d4820b2 ("drm/v3d: Use the new shmem helpers to reduce driver boilerplate.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321062731.GC21489@kadam

drm/vc4: Make sure to emit a tile coordinates between two MSAA loads.

The HW only executes a load once the tile coordinates packet happens,
and only tracks one at a time, so by emitting our two MSAA loads back
to back we would end up with an undefined color or Z buffer.

Fixes dEQP-EGL.functional.render.multi_context.gles2.rgb888_window

Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190206232550.12012-1-eric@anholt.net

drm/syncobj: add timeline signal ioctl for syncobj v5

v2: individually allocate chain array, since chain node is free independently.
v3: all existing points must be already signaled before cpu perform signal operation,
    so add check condition for that.
v4: remove v3 change and add checking to prevent out-of-order
v5: unify binary and timeline

Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: Tobias Hector <Tobias.Hector@amd.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/295792/?series=58813&rev=1

drm/syncobj: add transition iotcls between binary and timeline v2

we need to import/export timeline point.

v2: unify to one transfer ioctl

Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/295790/?series=58813&rev=1

drm/syncobj: use the timeline point in drm_syncobj_find_fence v4

Implement finding the right timeline point in drm_syncobj_find_fence.

v2: return -EINVAL when the point is not submitted yet.
v3: fix reference counting bug, add flags handling as well
v4: add timeout for find fence

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/295786/?series=58813&rev=1

drm/syncobj: add timeline payload query ioctl v6

user mode can query timeline payload.
v2: check return value of copy_to_user
v3: handle querying entry by entry
v4: rebase on new chain container, simplify interface
v5: query last signaled timeline point, not last point.
v6: add unorder point check

Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: Tobias Hector <Tobias.Hector@amd.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/295784/?series=58813&rev=1

drm/syncobj: add support for timeline point wait v8

points array is one-to-one match with syncobjs array.
v2:
add seperate ioctl for timeline point wait, otherwise break uapi.
v3:
userspace can specify two kinds waits::
a. Wait for time point to be completed.
b. and wait for time point to become available
v4:
rebase
v5:
add comment for xxx_WAIT_AVAILABLE
v6: rebase and rework on new container
v7: drop _WAIT_COMPLETED, it is the default anyway
v8: correctly handle garbage collected fences

Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: Tobias Hector <Tobias.Hector@amd.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/295782/?series=58813&rev=1

drm/syncobj: add new drm_syncobj_add_point interface v4

Use the dma_fence_chain object to create a timeline of fence objects
instead of just replacing the existing fence.

v2: rebase and cleanup
v3: fix garbage collection parameters
v4: add unorder point check, print a warn calltrace

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/295780/?series=58813&rev=1

dma-buf: add new dma_fence_chain container v7

Lockless container implementation similar to a dma_fence_array, but with
only two elements per node and automatic garbage collection.

v2: properly document dma_fence_chain_for_each, add dma_fence_chain_find_seqno,
    drop prev reference during garbage collection if it's not a chain fence.
v3: use head and iterator for dma_fence_chain_for_each
v4: fix reference count in dma_fence_chain_enable_signaling
v5: fix iteration when walking each chain node
v6: add __rcu for member 'prev' of struct chain node
v7: fix rcu warnings from kernel robot

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/295778/?series=58813&rev=1

drm: fallback to dma_alloc_coherent when memory encryption is active

We can't just map any randome page we get when memory encryption is
active.

Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.kernel.org/patch/10850833/

drm/sun4i: hdmi: add support for ddc-i2c-bus property

Sometimes it is desirabled to use a separate i2c controller for ddc
access.  This adds support for the ddc-i2c-bus property of the
hdmi-connector node, using the specified controller if provided.

Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190328130249.19356-1-mans@mansr.com

drm/stm: add sleep power management

Implements system sleep power management ops.

Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1553156120-13851-1-git-send-email-yannick.fertre@st.com

drm/stm: dw_mipi_dsi-stm: add sleep power management

Implements system sleep power management ops.

Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1553156033-13792-1-git-send-email-yannick.fertre@st.com

drm: rockchip: introduce rk3066 hdmi

The RK3066 HDMI TX serves as interface between a LCD Controller and
a HDMI bus. A HDMI TX consists of one HDMI transmitter controller and
one HDMI transmitter PHY. The interface has three (3) 8-bit data channels
which can be configured for a number of bus widths (8/10/12/16/20/24-bit)
and different video formats (RGB, YCbCr).

Features:
HDMI version 1.4a, HDCP revision 1.4 and
DVI version 1.0 compliant transmitter.
Supports DTV resolutions from 480i to 1080i/p HD.
Master I2C interface for a DDC connection.
HDMI TX supports multiple power save modes.
The HDMI TX input can switch between LCDC0 and LCDC1.
(Sound support is not included in this patch)

Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20190330095639.14626-2-jbx6244@gmail.com

dt-bindings: display: rockchip: add document for rk3066 hdmi

This patch adds a binding that describes the HDMI controller for
rk3066.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20190330095639.14626-5-jbx6244@gmail.com

drm/rockchip: vop: Support dithering to RGB666

Splits out the dither register bits and introduces
the same config enumerations as in the rockchip kernel tree.
Tested to fix the banding on my ASUS C201.

Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20190318154412.26994-1-urjaman@gmail.com

drm/virtio: rework resource creation workflow.

This patch moves the virtio_gpu_cmd_create_resource() call (which
notifies the host about the new resource created) into the
virtio_gpu_object_create() function.  That way we can call
virtio_gpu_cmd_create_resource() before ttm_bo_init(), so the host
already knows about the object when ttm initializes the object and calls
our driver callbacks.

Specifically the object is already created when the
virtio_gpu_ttm_tt_bind() callback invokes virtio_gpu_object_attach(),
so the extra virtio_gpu_object_attach() calls done after
virtio_gpu_object_create() are not needed any more.

The fence support for the create ioctl becomes a bit more tricky though.
The code moved into virtio_gpu_object_create() too.  We first submit the
(fenced) virtio_gpu_cmd_create_resource() command, then initialize the
ttm object, and finally attach just created object to the fence for the
command in case it didn't finish yet.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20190318113332.10900-6-kraxel@redhat.com

drm/virtio: params struct for virtio_gpu_cmd_create_resource_3d()

Add 3d resource parameters to virtio_gpu_object_params struct.  With
that in place we can use it for virtio_gpu_cmd_resource_create_3d()
calls.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20190318113332.10900-5-kraxel@redhat.com

drm/virtio: params struct for virtio_gpu_cmd_create_resource()

Add format, width and height fields to the virtio_gpu_object_params
struct.  With that in place we can use the parameter struct for
virtio_gpu_cmd_create_resource() calls too.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20190318113332.10900-4-kraxel@redhat.com

drm/virtio: use struct to pass params to virtio_gpu_object_create()

Create virtio_gpu_object_params, use that to pass object parameters to
virtio_gpu_object_create.  This is just the first step, followup patches
will add more parameters to the struct.  The plan is to use the struct
for all object parameters.

Drop unused "kernel" parameter for virtio_gpu_alloc_object(), it is
unused and always false.

Also drop "pinned" parameter.  virtio-gpu doesn't shuffle around
objects, so effecively they all are pinned anyway.  Hardcode
TTM_PL_FLAG_NO_EVICT so ttm knows.  Doesn't change much for the moment
as virtio-gpu supports TTM_PL_FLAG_TT only so there is no opportunity to
move around objects.  That'll probably change in the future though.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20190318113332.10900-3-kraxel@redhat.com

drm/virtio: move virtio_gpu_object_{attach, detach} calls.

Drop the dummy ttm backend implementation, add a real one for
TTM_PL_FLAG_TT objects.  The bin/unbind callbacks will call
virtio_gpu_object_{attach,detach}, to update the object state
on the host side, instead of invoking those calls from the
move_notify() callback.

With that in place the move and move_notify callbacks are not
needed any more, so drop them.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20190318113332.10900-2-kraxel@redhat.com

drm/virtio: add virtio-gpu-features debugfs file.

This file prints which features the virtio-gpu device has.

Also add "virtio-gpu-" prefix to the existing fence file,
to make clear this is a driver-specific debugfs file.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20190320083612.32067-1-kraxel@redhat.com

drm/virtio: remove set but not used variable 'vgdev'

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/gpu/drm/virtio/virtgpu_ttm.c: In function 'virtio_gpu_init_mem_type':
drivers/gpu/drm/virtio/virtgpu_ttm.c:117:28: warning:
 variable 'vgdev' set but not used [-Wunused-but-set-variable]

drivers/gpu/drm/virtio/virtgpu_ttm.c: In function 'virtio_gpu_bo_swap_notify':
drivers/gpu/drm/virtio/virtgpu_ttm.c:300:28: warning:
 variable 'vgdev' set but not used [-Wunused-but-set-variable]

It is never used since introduction in dc5698e80cf7 ("Add virtio gpu driver.")

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20190325092631.152060-1-yuehaibing@huawei.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>

drm/fb-helper: Fixup fill_info cleanup

I forgot the !CONFIG_FBDEV case. Also some kerneldoc needed more
adjusting.

Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190327125819.16478-1-daniel.vetter@ffwll.ch

drm/edid: Remove defunct EDID_QUIRK_FIRST_DETAILED_PREFERRED

Looks like EDID_QUIRK_FIRST_DETAILED_PREFERRED never did anything.
Its counterpart in f86EdidModes.c is properly hooked up but somehow
that functionality was lost when it was copied into the kernel.

The concensus seems to be that this quirk is a bit misguided
anyway so let's nuke the leftovers.

For posterity here are some links to known cases:
* Proview AY765C
  https://bugs.freedesktop.org/show_bug.cgi?id=15160
* Unknown Acer
  https://bugzilla.redhat.com/show_bug.cgi?id=284231 (got the
  reference from xf86EdidModes.c)
* Peacock Ergovision 19 (only in xf86EdidModes.c)
  https://bugzilla.redhat.com/show_bug.cgi?id=492359
* Philips 107p5 CRT
  "Reported on xorg@ with pastebin", didn't find the mail(s)

Cc: Adam Jackson <ajax@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322174244.23945-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>

drm/uapi: Remove unused DRM_DISPLAY_INFO_LEN

Remove the unused DRM_DISPLAY_INFO_LEN from the uapi headers.
I presume the original plan was to expose the display name
via getconnector, but looks like that never happened. So we have
the define for the length of the string but no string anywhere.

A quick scan didn't seem to reveal userspace referencing this
so hopefully we can just nuke it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326173401.7329-4-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm: Kill drm_display_info.name

drm_display_info.name is only ever set by a few panel drivers but
never actually used anywhere except in i915 debugfs code. Trash it.

v2: Fix typo in commit msg (Sam Ravnborg)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326173401.7329-3-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm: Fix tabs vs. spaces

A set of 8 spaces has snuck in. Replace with a tab, and
toss in an extra newline while at it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326173401.7329-2-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm: Nuke unused drm_display_info.pixel_clock

drm_display_info.pixel_clock is unused. Let's get rid of it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326173401.7329-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/fb-helper: Unexport fill_{var,info}

Not used by drivers anymore.

v2: Rebase

Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-21-daniel.vetter@ffwll.ch

drm/udl: Use drm_fb_helper_fill_info

This should not result in any changes.

v2: Rebase

v3: Don't forget to remove the info->par assignment (Noralf)

Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Emil Lundmark <lndmrk@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-19-daniel.vetter@ffwll.ch

drm/vboxvideo: Use drm_fb_helper_fill_info

This should not result in any changes.

v2: Rebase over vbox changes - vbox gained it's own line to fill
fix.id.

v3: Rebase

Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Alexander Kapshuk <alexander.kapshuk@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-20-daniel.vetter@ffwll.ch

drm/tegra: Use drm_fb_helper_fill_info

Another driver that didn't set fbinfo->fix.id before.

v2: Fix subject and rebase

Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-18-daniel.vetter@ffwll.ch

drm/rockchip: Use drm_fb_helper_fill_info

This will set an fb name for the first time!

v2: Rebase

Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-17-daniel.vetter@ffwll.ch

drm/radeon: Use drm_fb_helper_fill_info

This should not result in any changes.

v2: Rebase

Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-16-daniel.vetter@ffwll.ch

drm/omap: Use drm_fb_helper_fill_info

This changes the fb name from "omapdrm" to "omapdrmfb".

v2: Rebase

Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-15-daniel.vetter@ffwll.ch

drm/nouveau: Use drm_fb_helper_fill_info

This changes the fb name from "nouveaufb" to "nouveaudrmfb".

Aside: I wonder whether the in_interrupt() check is good enough for
the nouveau acceleration. Cargo-cult says drm_can_sleep() is needed,
which isn't actually working if you pick a .config without PREEMPT.
For the generic fbdev defio support we've gone with offloading
everything to a worker. For the non-accel callbacks (set_par, blank
and friends) checking for oops_in_progress is good enough to catch all
the evil calling contexts.

v2: Rebase

Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-14-daniel.vetter@ffwll.ch

drm/msm: Use drm_fb_helper_fill_info

This will change the fb name from "msm" to "msmdrmfb".

v2: Rebase

v3: Fix subject prefix (Noralf)

Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-13-daniel.vetter@ffwll.ch

drm/mga200g: Use drm_fb_helper_fill_info

Only changes the name of the fb from "mgadrmfb" to "mga200drmfb".

v2: Rebase

v3: Note the name change (Noralf)

Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Junwei Zhang <Jerry.Zhang@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-12-daniel.vetter@ffwll.ch