OSDN Git Service
Christoph Hellwig [Wed, 13 Jul 2011 11:43:48 +0000 (13:43 +0200)]
xfs: start periodic workers later
Start the periodic sync workers only after we have finished xfs_mountfs
and thus fully set up the filesystem structures. Without this we can
call into xfs_qm_sync before the quotainfo strucute is set up if the
mount takes unusually long, and probably hit other incomplete states
as well.
Also clean up the xfs_fs_fill_super error path by using consistent
label names, and removing an impossible to reach case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Reviewed-by: Alex Elder <aelder@sgi.com>
Alex Elder [Mon, 11 Jul 2011 14:51:44 +0000 (09:51 -0500)]
Revert "xfs: fix filesystsem freeze race in xfs_trans_alloc"
This reverts commit
7a249cf83da1813cfa71cfe1e265b40045eceb47.
That commit created a situation that could lead to a filesystem
hang. As Dave Chinner pointed out, xfs_trans_alloc() could hold a
reference to m_active_trans (i.e., keep it non-zero) and then wait
for SB_FREEZE_TRANS to complete. Meanwhile a filesystem freeze
request could set SB_FREEZE_TRANS and then wait for m_active_trans
to drop to zero. Nobody benefits from this sequence of events...
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Chandra Seetharaman [Thu, 9 Jun 2011 16:47:49 +0000 (16:47 +0000)]
xfs: remove variables that serve no purpose in xfs_alloc_ag_vextent_exact()
Remove two variables that serve no purpose in
xfs_alloc_ag_vextent_exact().
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Eric Sandeen [Fri, 20 May 2011 21:52:17 +0000 (21:52 +0000)]
xfs: consolidate & clarify mount sanity checks
Pavol pointed out that there is one silent error case in the mount
path, and that others are rather uninformative.
I've taken Pavol's suggested patch and extended it a bit to also:
* fix a message which says "turned off" but actually errors out
* consolidate the vaguely differentiated "SB sanity check [12]"
messages, and hexdump the superblock for analysis
Original-patch-by: Pavol Gono <Pavol.Gono@siemens.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:36:36 +0000 (14:36 +0200)]
xfs: avoid a few disk cache flushes
There is no need for a pre-flush when doing writing the second part of a
split log buffer, and if we are using an external log there is no need
to do a full cache flush of the log device at all given that all writes
to it use the FUA flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:36:32 +0000 (14:36 +0200)]
xfs: cleanup I/O-related buffer flags
Remove the unused and misnamed _XBF_RUN_QUEUES flag, rename XBF_LOG_BUFFER
to the more fitting XBF_SYNCIO, and split XBF_ORDERED into XBF_FUA and
XBF_FLUSH to allow more fine grained control over the bio flags. Also
cleanup processing of the flags in _xfs_buf_ioapply to make more sense,
and renumber the sparse flag number space to group flags by purpose.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:36:25 +0000 (14:36 +0200)]
xfs: return the buffer locked from xfs_buf_get_uncached
All other xfs_buf_get/read-like helpers return the buffer locked, make sure
xfs_buf_get_uncached isn't different for no reason. Half of the callers
already lock it directly after, and the others probably should also keep
it locked if only for consistency and beeing able to use xfs_buf_rele,
but I'll leave that for later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:36:19 +0000 (14:36 +0200)]
xfs: clean up buffer locking helpers
Rename xfs_buf_cond_lock and reverse it's return value to fit most other
trylock operations in the Kernel and XFS (with the exception of down_trylock,
after which xfs_buf_cond_lock was modelled), and replace xfs_buf_lock_val
with an xfs_buf_islocked for use in asserts, or and opencoded variant in
tracing. remove the XFS_BUF_* wrappers for all the locking helpers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:36:10 +0000 (14:36 +0200)]
xfs: remove the unused xfs_bufhash structure
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:36:05 +0000 (14:36 +0200)]
xfs: byteswap constants instead of variables
Micro-optimize various comparisms by always byteswapping the constant
instead of the variable, which allows to do the swap at compile instead
of runtime.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:35:58 +0000 (14:35 +0200)]
xfs: use generic get_unaligned_beXX helpers
Switch the shortform directory code over to use the generic
get_unaligned_beXX helpers instead of reinventing them. As a result
kill off xfs_arch.h and move the setting of XFS_NATIVE_HOST into
xfs_linux.h.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:35:53 +0000 (14:35 +0200)]
xfs: cleanup struct xfs_dir2_leaf
Simplify the confusing xfs_dir2_leaf structure. It is supposed to describe
an XFS dir2 leaf format btree block, but due to the variable sized nature
of almost all elements in it it can't actuall do anything close to that
job. Remove the members that are after the first variable sized array,
given that they could only be used for sizeof expressions that can as well
just use the underlying types directly, and make the ents array a real
C99 variable sized array.
Also factor out the xfs_dir2_leaf_size, to make the sizing of a leaf
entry which already was convoluted somewhat readable after using the
longer type names in the sizeof expressions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:35:50 +0000 (14:35 +0200)]
xfs: cleanup the definition of struct xfs_dir2_data_entry
Remove the tag member which is at a variable offset after the actual
name, and make name a real variable sized C99 array instead of the incorrect
one-sized array which confuses (not only) gcc.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:35:42 +0000 (14:35 +0200)]
xfs: kill struct xfs_dir2_data
Remove the confusing xfs_dir2_data structure. It is supposed to describe
an XFS dir2 data btree block, but due to the variable sized nature of
almost all elements in it it can't actuall do anything close to that
job. In addition to accessing the fixed offset header structure it was
only used to get a pointer to the first dir or unused entry after it,
which can be trivially replaced by pointer arithmetics on the header
pointer. For most users that is actually more natural anyway, as they
don't use a typed pointer but rather a character pointer for further
arithmetics.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:35:38 +0000 (14:35 +0200)]
xfs: avoid usage of struct xfs_dir2_data
In most places we can simply pass around and use the struct xfs_dir2_data_hdr,
which is the first and most important member of struct xfs_dir2_data instead
of the full structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:35:32 +0000 (14:35 +0200)]
xfs: kill struct xfs_dir2_block
Remove the confusing xfs_dir2_block structure. It is supposed to describe
an XFS dir2 block format btree block, but due to the variable sized nature
of almost all elements in it it can't actuall do anything close to that
job. In addition to accessing the fixed offset header structure it was
only used to get a pointer to the first dir or unused entry after it,
which can be trivially replaced by pointer arithmetics on the header
pointer. For most users that is actually more natural anyway, as they
don't use a typed pointer but rather a character pointer for further
arithmetics.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:35:27 +0000 (14:35 +0200)]
xfs: avoid usage of struct xfs_dir2_block
In most places we can simply pass around and use the struct xfs_dir2_data_hdr,
which is the first and most important member of struct xfs_dir2_block instead
of the full structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:35:19 +0000 (14:35 +0200)]
xfs: cleanup the definition of struct xfs_dir2_sf_entry
Remove the inumber member which is at a variable offset after the actual
name, and make name a real variable sized C99 array instead of the incorrect
one-sized array which confuses (not only) gcc. Based on this clean up
the helpers to calculate the entry size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:35:13 +0000 (14:35 +0200)]
xfs: kill struct xfs_dir2_sf
The list field of it is never cactually used, so all uses can simply be
replaced with the xfs_dir2_sf_hdr_t type that it has as first member.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:35:03 +0000 (14:35 +0200)]
xfs: cleanup shortform directory inode number handling
Refactor the shortform directory helpers that deal with the 32-bit vs
64-bit wide inode numbers into more sensible helpers, and kill the
xfs_intino_t typedef that is now superflous.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:34:59 +0000 (14:34 +0200)]
xfs: factor out xfs_dir2_leaf_find_entry
Add a new xfs_dir2_leaf_find_entry helper to factor out some duplicate code
from xfs_dir2_leaf_addname xfs_dir2_leafn_add. Found by Eric Sandeen using
an automated code duplication checker.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:34:51 +0000 (14:34 +0200)]
xfs: kill the unused struct xfs_sync_work
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:34:47 +0000 (14:34 +0200)]
xfs: remove i_transp
Remove the transaction pointer in the inode. It's only used to avoid
passing down an argument in the bmap code, and for a few asserts in
the transaction code right now.
Also use the local variable ip in a few more places in xfs_inode_item_unlock,
so that it isn't only used for debug builds after the above change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:34:42 +0000 (14:34 +0200)]
xfs: fix filesystsem freeze race in xfs_trans_alloc
As pointed out by Jan xfs_trans_alloc can race with a concurrent filesystem
freeze when it sleeps during the memory allocation. Fix this by moving the
wait_for_freeze call after the memory allocation. This means moving the
freeze into the low-level _xfs_trans_alloc helper, which thus grows a new
argument. Also fix up some comments in that area while at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:34:39 +0000 (14:34 +0200)]
xfs: improve sync behaviour in the face of aggressive dirtying
The following script from Wu Fengguang shows very bad behaviour in XFS
when aggressively dirtying data during a sync on XFS, with sync times
up to almost 10 times as long as ext4.
A large part of the issue is that XFS writes data out itself two times
in the ->sync_fs method, overriding the livelock protection in the core
writeback code, and another issue is the lock-less xfs_ioend_wait call,
which doesn't prevent new ioend from being queue up while waiting for
the count to reach zero.
This patch removes the XFS-internal sync calls and relies on the VFS
to do it's work just like all other filesystems do. Note that the
i_iocount wait which is rather suboptimal is simply removed here.
We already do it in ->write_inode, which keeps the current supoptimal
behaviour. We'll eventually need to remove that as well, but that's
material for a separate commit.
------------------------------ snip ------------------------------
#!/bin/sh
umount /dev/sda7
mkfs.xfs -f /dev/sda7
# mkfs.ext4 /dev/sda7
# mkfs.btrfs /dev/sda7
mount /dev/sda7 /fs
echo $((50<<20)) > /proc/sys/vm/dirty_bytes
pid=
for i in `seq 10`
do
dd if=/dev/zero of=/fs/zero-$i bs=1M count=1000 &
pid="$pid $!"
done
sleep 1
tic=$(date +'%s')
sync
tac=$(date +'%s')
echo
echo sync time: $((tac-tic))
egrep '(Dirty|Writeback|NFS_Unstable)' /proc/meminfo
pidof dd > /dev/null && { kill -9 $pid; echo sync NOT livelocked; }
------------------------------ snip ------------------------------
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:34:34 +0000 (14:34 +0200)]
xfs: split xfs_itruncate_finish
Split the guts of xfs_itruncate_finish that loop over the existing extents
and calls xfs_bunmapi on them into a new helper, xfs_itruncate_externs.
Make xfs_attr_inactive call it directly instead of xfs_itruncate_finish,
which allows to simplify the latter a lot, by only letting it deal with
the data fork. As a result xfs_itruncate_finish is renamed to
xfs_itruncate_data to make its use case more obvious.
Also remove the sync parameter from xfs_itruncate_data, which has been
unessecary since the introduction of the busy extent list in 2002, and
completely dead code since 2003 when the XFS_BMAPI_ASYNC parameter was
made a no-op.
I can't actually see why the xfs_attr_inactive needs to set the transaction
sync, but let's keep this patch simple and without changes in behaviour.
Also avoid passing a useless argument to xfs_isize_check, and make it
private to xfs_inode.c.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:34:30 +0000 (14:34 +0200)]
xfs: kill xfs_itruncate_start
xfs_itruncate_start is a rather length wrapper that evaluates to a call
to xfs_ioend_wait and xfs_tosspages, and only has two callers.
Instead of using the complicated checks left over from IRIX where we
can to truncate the pagecache just call xfs_tosspages
(aka truncate_inode_pages) directly as we want to get rid of all data
after i_size, and truncate_inode_pages handles incorrect alignments
and too large offsets just fine.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:34:26 +0000 (14:34 +0200)]
xfs: always log timestamp updates in xfs_setattr_size
Get rid of the special case where we use unlogged timestamp updates for
a truncate to the current inode size, and just call xfs_setattr_nonsize
for it to treat it like a utimes calls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:34:23 +0000 (14:34 +0200)]
xfs: split xfs_setattr
Split up xfs_setattr into two functions, one for the complex truncate
handling, and one for the trivial attribute updates. Also move both
new routines to xfs_iops.c as they are fairly Linux-specific.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:34:18 +0000 (14:34 +0200)]
xfs: work around bogus gcc warning in xfs_allocbt_init_cursor
GCC 4.6 complains about an array subscript is above array bounds when
using the btree index to index into the agf_levels array. The only
two indices passed in are 0 and 1, and we have an assert insuring that.
Replace the trick of using the array index directly with using constants
in the already existing branch for assigning the XFS_BTREE_LASTREC_UPDATE
flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:34:14 +0000 (14:34 +0200)]
xfs: re-enable non-blocking behaviour in xfs_map_blocks
The non-blockig behaviour in xfs_vm_writepage currently is conditional on
having both the WB_SYNC_NONE sync_mode and the nonblocking flag set.
The latter used to be used by both pdflush, kswapd and a few other places
in older kernels, but has been fading out starting with the introduction
of the per-bdi flusher threads.
Enable the non-blocking behaviour for all WB_SYNC_NONE calls to get back
the behaviour we want.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Christoph Hellwig [Fri, 8 Jul 2011 12:34:05 +0000 (14:34 +0200)]
xfs: PF_FSTRANS should never be set in ->writepage
Now that we reject direct reclaim in addition to always using GFP_NOFS
allocation there's no chance we'll ever end up in ->writepage with
PF_FSTRANS set. Add a WARN_ON if we hit this case, and stop checking
if we'd actually need to start a transaction.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Dave Chinner [Mon, 4 Jul 2011 05:27:36 +0000 (05:27 +0000)]
xfs: unpin stale inodes directly in IOP_COMMITTED
When inodes are marked stale in a transaction, they are treated
specially when the inode log item is being inserted into the AIL.
It tries to avoid moving the log item forward in the AIL due to a
race condition with the writing the underlying buffer back to disk.
The was "fixed" in commit
de25c18 ("xfs: avoid moving stale inodes
in the AIL").
To avoid moving the item forward, we return a LSN smaller than the
commit_lsn of the completing transaction, thereby trying to trick
the commit code into not moving the inode forward at all. I'm not
sure this ever worked as intended - it assumes the inode is already
in the AIL, but I don't think the returned LSN would have been small
enough to prevent moving the inode. It appears that the reason it
worked is that the lower LSN of the inodes meant they were inserted
into the AIL and flushed before the inode buffer (which was moved to
the commit_lsn of the transaction).
The big problem is that with delayed logging, the returning of the
different LSN means insertion takes the slow, non-bulk path. Worse
yet is that insertion is to a position -before- the commit_lsn so it
is doing a AIL traversal on every insertion, and has to walk over
all the items that have already been inserted into the AIL. It's
expensive.
To compound the matter further, with delayed logging inodes are
likely to go from clean to stale in a single checkpoint, which means
they aren't even in the AIL at all when we come across them at AIL
insertion time. Hence these were all getting inserted into the AIL
when they simply do not need to be as inodes marked XFS_ISTALE are
never written back.
Transactional/recovery integrity is maintained in this case by the
other items in the unlink transaction that were modified (e.g. the
AGI btree blocks) and committed in the same checkpoint.
So to fix this, simply unpin the stale inodes directly in
xfs_inode_item_committed() and return -1 to indicate that the AIL
insertion code does not need to do any further processing of these
inodes.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Dave Chinner [Thu, 23 Jun 2011 01:35:01 +0000 (01:35 +0000)]
xfs: prevent bogus assert when trying to remove non-existent attribute
If the attribute fork on an inode is in btree format and has
multiple levels (i.e node format rather than leaf format), then a
lookup failure will trigger an assert failure in xfs_da_path_shift
if the flag XFS_DA_OP_OKNOENT is not set. This flag is used to
indicate to the directory btree code that not finding an entry is
not a fatal error. In the case of doing a lookup for a directory
name removal, this is valid as a user cannot insert an arbitrary
name to remove from the directory btree.
However, in the case of the attribute tree, a user has direct
control over the attribute name and can ask for any random name to
be removed without any validation. In this case, fsstress is asking
for a non-existent user.selinux attribute to be removed, and that is
causing xfs_da_path_shift() to fall off the bottom of the tree where
it asserts that a lookup failure is allowed. Because the flag is not
set, we die a horrible death on a debug enable kernel.
Prevent this assert from firing on attribute removes by adding the
op_flag XFS_DA_OP_OKNOENT to atribute removal operations.
Discovered when testing on a SELinux enabled system by fsstress in
test 070 by trying to remove a non-existent user.selinux attribute.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Dave Chinner [Thu, 23 Jun 2011 01:35:00 +0000 (01:35 +0000)]
xfs: clear XFS_IDIRTY_RELEASE on truncate down
When an inode is truncated down, speculative preallocation is
removed from the inode. This should also reset the state bits for
controlling whether preallocation is subsequently removed when the
file is next closed. The flag is not being cleared, so repeated
operations on a file that first involve a truncate (e.g. multiple
repeated dd invocations on a file) give different file layouts for
the second and subsequent invocations.
Fix this by clearing the XFS_IDIRTY_RELEASE state bit when the
XFS_ITRUNCATED bit is detected in xfs_release() and hence ensure
that speculative delalloc is removed on files that have been
truncated down.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Dave Chinner [Thu, 23 Jun 2011 01:34:59 +0000 (01:34 +0000)]
xfs: reset inode per-lifetime state when recycling it
XFS inodes has several per-lifetime state fields that determine the
behaviour of the inode. These state fields are not all reset when an
inode is reused from the reclaimable state.
This can lead to unexpected behaviour of the new inode such as
speculative preallocation not being truncated away in the expected
manner for local files until the inode is subsequently truncated,
freed or cycles out of the cache. It can also lead to an inode being
considered to be a filestream inode or having been truncated when
that is not the case.
Rework the reinitialisation of the inode when it is recycled to
ensure that it is pristine before it is reused. While there, also
fix the resetting of state flags in the recycling error paths so the
inode does not become unreclaimable.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Christoph Hellwig [Thu, 16 Jun 2011 12:02:23 +0000 (12:02 +0000)]
xfs: make log devices with write back caches work
There's no reason not to support cache flushing on external log devices.
The only thing this really requires is flushing the data device first
both in fsync and log commits. A side effect is that we also have to
remove the barrier write test during mount, which has been superflous
since the new FLUSH+FUA code anyway. Also use the chance to flush the
RT subvolume write cache before the fsync commit, which is required
for correct semantics.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Al Viro [Sun, 5 Jun 2011 11:12:31 +0000 (11:12 +0000)]
xfs: fix ->mknod() return value on xfs_get_acl() failure
->mknod() should return negative on errors and PTR_ERR() gives
already negative value...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Linus Torvalds [Mon, 6 Jun 2011 09:06:33 +0000 (18:06 +0900)]
Linux 3.0-rc2
Hugh Dickins [Mon, 6 Jun 2011 05:03:13 +0000 (22:03 -0700)]
mm: fix ENOSPC returned by handle_mm_fault()
Al Viro observes that in the hugetlb case, handle_mm_fault() may return
a value of the kind ENOSPC when its caller is expecting a value of the
kind VM_FAULT_SIGBUS: fix alloc_huge_page()'s failure returns.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 6 Jun 2011 08:51:28 +0000 (17:51 +0900)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: usb - turn off de-emphasis in s/pdif for cm6206
ALSA: asihpi: Use angle brackets for system includes
ALSA: fm801: add error handling if auto-detect fails
ALSA: hda - Check pin support EAPD in ad198x_power_eapd_write
ALSA: hda - Fix HP and Front pins of ad1988/ad1989 in ad198x_power_eapd()
ALSA: 6fire: Don't leak firmware in error path
ASoC: Fix wm_hubs input PGA ZC bits
ASoC: Fix dapm_is_shared_kcontrol so everything isn't shared
Linus Torvalds [Mon, 6 Jun 2011 08:48:02 +0000 (17:48 +0900)]
Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
hwmon: (max6642): Better chip detection schema
hwmon: (coretemp) Further relax temperature range checks
hwmon: (coretemp) Fix TjMax detection for older CPUs
hwmon: (coretemp) Relax target temperature range check
hwmon: (max6642) Rename temp_fault sysfs attribute to temp2_fault
Takashi Iwai [Mon, 6 Jun 2011 07:28:49 +0000 (09:28 +0200)]
Merge branch 'fix/asoc' into for-linus
Linus Torvalds [Sat, 4 Jun 2011 23:11:11 +0000 (08:11 +0900)]
Merge branch 'for-linus' of git://android.git./kernel/tegra
* 'for-linus' of git://android.git.kernel.org/kernel/tegra:
ARM: Tegra: Harmony: Fix conflicting GPIO numbering
Stephen Warren [Tue, 31 May 2011 21:14:07 +0000 (15:14 -0600)]
ARM: Tegra: Harmony: Fix conflicting GPIO numbering
Currently, both the WM8903 and TPS6586x chips attempt to register with
gpiolib using the same GPIO numbers. This causes the audio driver to
fail to initialize.
To solve this, add a define to board-harmony.h for the TPS6586x, and make
board-harmony-power.c use this define, instead of directly referencing
TEGRA_NR_GPIOS.
This fixes a regression introduced by commit
6f168f2fa60f87e85e0df25e87e2372f22f5eb7c.
ARM: tegra: harmony: initialize the TPS65862 PMIC
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Linus Torvalds [Sat, 4 Jun 2011 21:17:23 +0000 (06:17 +0900)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/btrfs-unstable
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (25 commits)
btrfs: fix uninitialized variable warning
btrfs: add helper for fs_info->closing
Btrfs: add mount -o inode_cache
btrfs: scrub: add explicit plugging
btrfs: use btrfs_ino to access inode number
Btrfs: don't save the inode cache if we are deleting this root
btrfs: false BUG_ON when degraded
Btrfs: don't save the inode cache in non-FS roots
Btrfs: make sure we don't overflow the free space cache crc page
Btrfs: fix uninit variable in the delayed inode code
btrfs: scrub: don't reuse bios and pages
Btrfs: leave spinning on lookup and map the leaf
Btrfs: check for duplicate entries in the free space cache
Btrfs: don't try to allocate from a block group that doesn't have enough space
Btrfs: don't always do readahead
Btrfs: try not to sleep as much when doing slow caching
Btrfs: kill BTRFS_I(inode)->block_group
Btrfs: don't look at the extent buffer level 3 times in a row
Btrfs: map the node block when looking for readahead targets
Btrfs: set range_start to the right start in count_range_bits
...
Per Dalén [Thu, 26 May 2011 13:08:53 +0000 (09:08 -0400)]
hwmon: (max6642): Better chip detection schema
Improve detection of MAX6642 by reading non existing registers (0x04, 0x06
and 0xff). Reading those registers returns the previously read value.
Signed-off-by: Per Dalen <per.dalen@appeartv.com>
[guenter.roeck@ericsson.com: added second set of register reads]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Linus Torvalds [Sat, 4 Jun 2011 14:19:51 +0000 (23:19 +0900)]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] Fix oops caused by queue refcounting failure
Linus Torvalds [Sat, 4 Jun 2011 14:16:00 +0000 (23:16 +0900)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (40 commits)
tg3: Fix tg3_skb_error_unmap()
net: tracepoint of net_dev_xmit sees freed skb and causes panic
drivers/net/can/flexcan.c: add missing clk_put
net: dm9000: Get the chip in a known good state before enabling interrupts
drivers/net/davinci_emac.c: add missing clk_put
af-packet: Add flag to distinguish VID 0 from no-vlan.
caif: Fix race when conditionally taking rtnl lock
usbnet/cdc_ncm: add missing .reset_resume hook
vlan: fix typo in vlan_dev_hard_start_xmit()
net/ipv4: Check for mistakenly passed in non-IPv4 address
iwl4965: correctly validate temperature value
bluetooth l2cap: fix locking in l2cap_global_chan_by_psm
ath9k: fix two more bugs in tx power
cfg80211: don't drop p2p probe responses
Revert "net: fix section mismatches"
drivers/net/usb/catc.c: Fix potential deadlock in catc_ctrl_run()
sctp: stop pending timers and purge queues when peer restart asoc
drivers/net: ks8842 Fix crash on received packet when in PIO mode.
ip_options_compile: properly handle unaligned pointer
iwlagn: fix incorrect PCI subsystem id for 6150 devices
...
David Sterba [Fri, 3 Jun 2011 14:29:08 +0000 (16:29 +0200)]
btrfs: fix uninitialized variable warning
With Linus' tree, today's linux-next build (powercp ppc64_defconfig)
produced this warning:
fs/btrfs/delayed-inode.c: In function 'btrfs_delayed_update_inode':
fs/btrfs/delayed-inode.c:1598:6: warning: 'ret' may be used
uninitialized in this function
Introduced by commit
16cdcec736cd ("btrfs: implement delayed inode items
operation").
This fixes a bug in btrfs_update_inode(): if the returned value from
btrfs_delayed_update_inode is a nonzero garbage, inode stat data are not
updated and several call paths may hit a BUG_ON or fail with strange
code.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David Sterba <dsterba@suse.cz>
David Sterba [Tue, 31 May 2011 16:07:27 +0000 (18:07 +0200)]
btrfs: add helper for fs_info->closing
wrap checking of filesystem 'closing' flag and fix a few missing memory
barriers.
Signed-off-by: David Sterba <dsterba@suse.cz>
Chris Mason [Fri, 3 Jun 2011 13:36:29 +0000 (09:36 -0400)]
Btrfs: add mount -o inode_cache
This makes the inode map cache default to off until we
fix the overflow problem when the free space crcs don't fit
inside a single page.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Arne Jansen [Sat, 28 May 2011 20:58:38 +0000 (20:58 +0000)]
btrfs: scrub: add explicit plugging
With the removal of the implicit plugging scrub ends up doing more and
smaller I/O than necessary. This patch adds explicit plugging per chunk.
Signed-off-by: Arne Jansen <sensille@gmx.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
David Sterba [Tue, 31 May 2011 17:08:14 +0000 (17:08 +0000)]
btrfs: use btrfs_ino to access inode number
commit
4cb5300bc ("Btrfs: add mount -o auto_defrag") accesses inode
number directly while it should use the helper with the new inode
number allocator.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik [Tue, 31 May 2011 19:33:33 +0000 (19:33 +0000)]
Btrfs: don't save the inode cache if we are deleting this root
With xfstest 254 I can panic the box every time with the inode number caching
stuff on. This is because we clean the inodes out when we delete the subvolume,
but then we write out the inode cache which adds an inode to the subvolume inode
tree, and then when it gets evicted again the root gets added back on the dead
roots list and is deleted again, so we have a double free. To stop this from
happening just return 0 if refs is 0 (and we're not the tree root since tree
root always has refs of 0). With this fix 254 no longer panics. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Tested-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Arne Jansen [Mon, 30 May 2011 08:36:16 +0000 (08:36 +0000)]
btrfs: false BUG_ON when degraded
In degraded mode the struct btrfs_device of missing devs don't have
device->name set. A kstrdup of NULL correctly returns NULL. Don't
BUG in this case.
Signed-off-by: Arne Jansen <sensille@gmx.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
liubo [Wed, 1 Jun 2011 09:42:49 +0000 (09:42 +0000)]
Btrfs: don't save the inode cache in non-FS roots
This adds extra checks to make sure the inode map we are caching really
belongs to a FS root instead of a special relocation tree. It
prevents crashes during balancing operations.
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Chris Mason [Fri, 3 Jun 2011 05:26:53 +0000 (01:26 -0400)]
Btrfs: make sure we don't overflow the free space cache crc page
The free space cache uses only one page for crcs right now,
which means we can't have a cache file bigger than the
crcs we can fit in the first page. This adds a check to
enforce that restriction.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Chris Mason [Fri, 3 Jun 2011 05:13:45 +0000 (01:13 -0400)]
Btrfs: fix uninit variable in the delayed inode code
The nitems counter needs to start at zero
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Arne Jansen [Sat, 28 May 2011 19:57:55 +0000 (21:57 +0200)]
btrfs: scrub: don't reuse bios and pages
The current scrub implementation reuses bios and pages as often as possible,
allocating them only on start and releasing them when finished. This leads
to more problems with the block layer than it's worth. The elevator gets
confused when there are more pages added to the bio than bi_size suggests.
This patch completely rips out the reuse of bios and pages and allocates
them freshly for each submit.
Signed-off-by: Arne Jansen <sensille@gmx.net>
Signed-off-by: Chris Maosn <chris.mason@oracle.com>
Linus Torvalds [Fri, 3 Jun 2011 23:11:26 +0000 (08:11 +0900)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
* 'for-linus' of git://git.kernel.dk/linux-block:
block: Use hlist_entry() for io_context.cic_list.first
cfq-iosched: Remove bogus check in queue_fail path
xen/blkback: potential null dereference in error handling
xen/blkback: don't call vbd_size() if bd_disk is NULL
block: blkdev_get() should access ->bd_disk only after success
CFQ: Fix typo and remove unnecessary semicolon
block: remove unwanted semicolons
Revert "block: Remove extra discard_alignment from hd_struct."
nbd: adjust 'max_part' according to part_shift
nbd: limit module parameters to a sane value
nbd: pass MSG_* flags to kernel_recvmsg()
block: improve the bio_add_page() and bio_add_pc_page() descriptions
Linus Torvalds [Fri, 3 Jun 2011 23:04:10 +0000 (08:04 +0900)]
Merge branch 'for-linus' of git://git./linux/kernel/git/vapier/blackfin
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
Blackfin: strncpy: fix handling of zero lengths
Linus Torvalds [Fri, 3 Jun 2011 23:03:16 +0000 (08:03 +0900)]
Merge branch 'stable' of git://git./linux/kernel/git/cmetcalf/linux-tile
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
asm-generic/unistd.h: support sendmmsg syscall
tile: enable CONFIG_BUGVERBOSE
Linus Torvalds [Fri, 3 Jun 2011 22:59:32 +0000 (07:59 +0900)]
Merge branch 'linux-next' of git://git.infradead.org/ubifs-2.6
* 'linux-next' of git://git.infradead.org/ubifs-2.6:
UBIFS: fix-up free space earlier
UBIFS: intialize LPT earlier
UBIFS: assert no fixup when writing a node
UBIFS: fix clean znode counter corruption in error cases
UBIFS: fix memory leak on error path
UBIFS: fix shrinker object count reports
UBIFS: fix recovery broken by the previous recovery fix
UBIFS: amend ubifs_recover_leb interface
UBIFS: introduce a "grouped" journal head flag
UBIFS: supress false error messages
Linus Torvalds [Fri, 3 Jun 2011 22:58:48 +0000 (07:58 +0900)]
Merge branch 'for-linus' of git://git./linux/kernel/git/rostedt/linux-2.6-ktest
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-ktest:
ktest: Ignore unset values of the minconfig in config_bisect
ktest: Fix result of rebooting the kernel
ktest: Fix off-by-one in config bisect result
Linus Torvalds [Fri, 3 Jun 2011 22:53:23 +0000 (07:53 +0900)]
Merge branch 'rmobile-fixes-for-linus' of git://git./linux/kernel/git/lethal/sh-2.6
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: mach-shmobile: add DMAC clock definitions on SH7372
ARM: arch-shmobile: support SDHI card detection on mackerel, using a GPIO
sh_mobile_meram: MERAM platform data for LCDC
Linus Torvalds [Fri, 3 Jun 2011 22:04:25 +0000 (07:04 +0900)]
Merge branch 'sh-fixes-for-linus' of git://git./linux/kernel/git/lethal/sh-2.6
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
dmaengine: shdma: fix a regression: initialise DMA channels for memcpy
dmaengine: shdma: Fix up fallout from runtime PM changes.
Revert "clocksource: sh_cmt: Runtime PM support"
Revert "clocksource: sh_tmu: Runtime PM support"
sh: Fix up asm-generic/ptrace.h fallout.
sh64: Move from P1SEG to CAC_ADDR for consistent sync.
sh64: asm/pgtable.h needs asm/mmu.h
sh: asm/tlb.h needs linux/swap.h
sh: mark DMA slave ID 0 as invalid
sh: Update shmin to reflect PIO dependency.
sh: arch/sh/kernel/process_32.c needs linux/prefetch.h.
sh: add MMCIF runtime PM support on ecovec
sh: switch ap325rxa to dynamically manage the platform camera
Linus Torvalds [Fri, 3 Jun 2011 22:00:50 +0000 (07:00 +0900)]
Revert "ASoC: Update cx20442 for TTY API change"
This reverts commit
ed0bd2333cffc3d856db9beb829543c1dfc00982.
Since we reverted the TTY API change, we should revert the ASoC update
to it too.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 3 Jun 2011 21:33:24 +0000 (06:33 +0900)]
Revert "tty: make receive_buf() return the amout of bytes received"
This reverts commit
b1c43f82c5aa265442f82dba31ce985ebb7aa71c.
It was broken in so many ways, and results in random odd pty issues.
It re-introduced the buggy schedule_work() in flush_to_ldisc() that can
cause endless work-loops (see commit
a5660b41af6a: "tty: fix endless
work loop when the buffer fills up").
It also used an "unsigned int" return value fo the ->receive_buf()
function, but then made multiple functions return a negative error code,
and didn't actually check for the error in the caller.
And it didn't actually work at all. BenH bisected down odd tty behavior
to it:
"It looks like the patch is causing some major malfunctions of the X
server for me, possibly related to PTYs. For example, cat'ing a
large file in a gnome terminal hangs the kernel for -minutes- in a
loop of what looks like flush_to_ldisc/workqueue code, (some ftrace
data in the quoted bits further down).
...
Some more data: It -looks- like what happens is that the
flush_to_ldisc work queue entry constantly re-queues itself (because
the PTY is full ?) and the workqueue thread will basically loop
forver calling it without ever scheduling, thus starving the consumer
process that could have emptied the PTY."
which is pretty much exactly the problem we fixed in
a5660b41af6a.
Milton Miller pointed out the 'unsigned int' issue.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Milton Miller <miltonm@bga.com>
Cc: Stefan Bigler <stefan.bigler@keymile.com>
Cc: Toby Gray <toby.gray@realvnc.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
John W. Linville [Fri, 3 Jun 2011 18:31:50 +0000 (14:31 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6 into for-davem
Eric Lammerts [Fri, 27 May 2011 22:16:52 +0000 (18:16 -0400)]
ALSA: usb - turn off de-emphasis in s/pdif for cm6206
CM6206: Turn off de-emphasis channel status bit in S/PDIF output.
Signed-off-by: Eric Lammerts <eric@lammerts.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ben Gardiner [Mon, 30 May 2011 18:56:16 +0000 (14:56 -0400)]
UBIFS: fix-up free space earlier
The free space fixup is currently initiated during mount after the call to
ubifs_write_master() which results in a write to PEBs; this has been observed
with the patch 'assert no fixup when writing a node' applied:
Move the free space fixup on mount to before the calls to
ubifs_recover_inl_heads() and ubifs_write_master(). This results in no
assertions with the previously mentioned patch applied.
Artem: tweaked the patch a bit
Signed-off-by: Ben Gardiner <bengardiner@nanometrics>
Reviewed-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Ben Gardiner [Mon, 30 May 2011 18:56:15 +0000 (14:56 -0400)]
UBIFS: intialize LPT earlier
The current 'mount_ubifs()' implementation does not initialize the LPT until the
the master node is marked dirty. Move the LPT initialization to before marking
the master node dirty. This is a preparation for the next patch which will move
the free-space-fixup check to before marking the master node dirty, because we
have to fix-up the free space before doing any writes.
Artem: massaged the patch and commit message.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Ben Gardiner [Mon, 30 May 2011 18:56:14 +0000 (14:56 -0400)]
UBIFS: assert no fixup when writing a node
The current free space fixup can result in some writing to the UBI volume
when the space_fixup flag is set.
To catch instances where UBIFS is writing to the NAND while the space_fixup
flag is set, add an assert to ubifs_write_node().
Artem: tweaked the patch, added similar assertion to the write buffer
write path.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Artem Bityutskiy [Tue, 31 May 2011 11:26:07 +0000 (14:26 +0300)]
UBIFS: fix clean znode counter corruption in error cases
UBIFS maintains per-filesystem and global clean znode counters
('c->clean_zn_cnt' and 'ubifs_clean_zn_cnt'). It is important to maintain
correct values there since the shrinker relies on 'ubifs_clean_zn_cnt'.
However, in case of failures during commit the counters were corrupted. E.g.,
if a failure happens in the middle of 'write_index()', then some nodes in the
commit list ('c->cnext') are marked as clean, and some are marked as dirty. And
the 'ubifs_destroy_tnc_subtree()' frees does not retrun correct count, and we
end up with non-zero 'c->clean_zn_cnt' when unmounting. This means that if we
have 2 file-sytem and one of them fails, and we unmount it,
'ubifs_clean_zn_cnt' stays incorrect and confuses the shrinker.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Artem Bityutskiy [Tue, 31 May 2011 05:40:40 +0000 (08:40 +0300)]
UBIFS: fix memory leak on error path
UBIFS leaks memory on error path in 'ubifs_jnl_update()' in case of write
failure because it forgets to free the 'struct ubifs_dent_node *dent' object.
Although the object is small, the alignment can make it large - e.g., 2KiB
if the min. I/O unit is 2KiB.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org
Artem Bityutskiy [Tue, 31 May 2011 04:03:21 +0000 (07:03 +0300)]
UBIFS: fix shrinker object count reports
Sometimes VM asks the shrinker to return amount of objects it can shrink,
and we return the ubifs_clean_zn_cnt in that case. However, it is possible
that this counter is negative for a short period of time, due to the way
UBIFS TNC code updates it. And I can observe the following warnings sometimes:
shrink_slab: ubifs_shrinker+0x0/0x2b7 [ubifs] negative objects to delete nr=-
8541616642706119788
This patch makes sure UBIFS never returns negative count of objects.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org
Steven Miao [Wed, 1 Jun 2011 07:52:41 +0000 (15:52 +0800)]
Blackfin: strncpy: fix handling of zero lengths
The jump to 4f will cause the NUL padding loop to run at least one time,
so if string length is zero just jump to the end. Otherwise we wrongly
write one NUL byte when size==0.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Joe Perches [Fri, 3 Jun 2011 09:28:49 +0000 (02:28 -0700)]
ALSA: asihpi: Use angle brackets for system includes
Use the normal include style.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dan Carpenter [Thu, 26 May 2011 08:47:35 +0000 (11:47 +0300)]
ALSA: fm801: add error handling if auto-detect fails
In the original code if auto detect failed and tea575x_tuner == 4
then we copy bogus information to chip->tea.card. I've changed the
autodetect code to cleanup and return -ENODEV on error instead.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Raymond Yau [Wed, 1 Jun 2011 07:09:48 +0000 (15:09 +0800)]
ALSA: hda - Check pin support EAPD in ad198x_power_eapd_write
Check whether the pin supports EAPD in ad198x_power_eapd_write.
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Fri, 3 Jun 2011 08:05:02 +0000 (10:05 +0200)]
ALSA: hda - Fix HP and Front pins of ad1988/ad1989 in ad198x_power_eapd()
In ad198x_power_eapd(), wrong pin NIDs are used for controlling EAPD for
HP and Front outputs of AD1988/AD1989. These are actually same with the
ones for AD1984 & co, port-A is 0x11 and port-D 0x12.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Matt Carlson [Thu, 2 Jun 2011 13:01:39 +0000 (13:01 +0000)]
tg3: Fix tg3_skb_error_unmap()
This function attempts to free one fragment beyond the number of
fragments that were actually mapped. This patch brings back the limit
to the correct spot.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Koki Sanagi [Mon, 30 May 2011 21:48:34 +0000 (21:48 +0000)]
net: tracepoint of net_dev_xmit sees freed skb and causes panic
Because there is a possibility that skb is kfree_skb()ed and zero cleared
after ndo_start_xmit, we should not see the contents of skb like skb->len and
skb->dev->name after ndo_start_xmit. But trace_net_dev_xmit does that
and causes panic by NULL pointer dereference.
This patch fixes trace_net_dev_xmit not to see the contents of skb directly.
If you want to reproduce this panic,
1. Get tracepoint of net_dev_xmit on
2. Create 2 guests on KVM
2. Make 2 guests use virtio_net
4. Execute netperf from one to another for a long time as a network burden
5. host will panic(It takes about 30 minutes)
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Metcalf [Thu, 2 Jun 2011 18:21:45 +0000 (14:21 -0400)]
asm-generic/unistd.h: support sendmmsg syscall
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Jesper Juhl [Mon, 30 May 2011 10:49:01 +0000 (12:49 +0200)]
ALSA: 6fire: Don't leak firmware in error path
One of the error paths in
sound/usb/6fire/firmware.c::usb6fire_fw_ezusb_upload() neglects to free
the memory allocated for the firmware before returning, thus leaking the
memory.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Steven Rostedt [Thu, 2 Jun 2011 03:27:19 +0000 (23:27 -0400)]
ktest: Ignore unset values of the minconfig in config_bisect
By ignoring the unset values of the minconfig in deciding
what to test in the config_bisect can cause the problem
config from being tested too.
Just do not test the configs that are set in the minconfig.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Steven Rostedt [Thu, 2 Jun 2011 03:25:13 +0000 (23:25 -0400)]
ktest: Fix result of rebooting the kernel
The command that is called that reboots the kernel may fail
but the return code is not passed back to the ktest.pl script.
This is because a ';' is used between the two commands and
if the second command fails, only the first command's return
code is returned. Using a '&&' between the two commands fixes
this.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Steven Rostedt [Thu, 2 Jun 2011 03:22:30 +0000 (23:22 -0400)]
ktest: Fix off-by-one in config bisect result
Because in perl the array size returned by $#arr, is the last
index and not the actually size of the array, we end the config
bisect early, thinking there is only one config left when there
are in fact two. Thus the result has a 50% chance of picking
the correct config that caused the problem.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Jens Axboe [Thu, 2 Jun 2011 11:14:15 +0000 (13:14 +0200)]
Merge branch 'for-jens/xen-blkback.fixes' of git://git./linux/kernel/git/konrad/xen into for-linus
Paul Bolle [Thu, 2 Jun 2011 11:05:02 +0000 (13:05 +0200)]
block: Use hlist_entry() for io_context.cic_list.first
list_entry() and hlist_entry() are both simply aliases for
container_of(), but since io_context.cic_list.first is an hlist_node one
should at least use the correct alias.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Paul Bolle [Thu, 2 Jun 2011 11:05:02 +0000 (13:05 +0200)]
cfq-iosched: Remove bogus check in queue_fail path
queue_fail can only be reached if cic is NULL, so its check for cic must
be bogus.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
James Bottomley [Wed, 25 May 2011 20:52:14 +0000 (15:52 -0500)]
[SCSI] Fix oops caused by queue refcounting failure
In certain circumstances, we can get an oops from a torn down device.
Most notably this is from CD roms trying to call scsi_ioctl. The root
cause of the problem is the fact that after scsi_remove_device() has
been called, the queue is fully torn down. This is actually wrong
since the queue can be used until the sdev release function is called.
Therefore, we add an extra reference to the queue which is released in
sdev->release, so the queue always exists.
Reported-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Julia Lawall [Wed, 1 Jun 2011 19:48:50 +0000 (19:48 +0000)]
drivers/net/can/flexcan.c: add missing clk_put
The failed_get label is used after the call to clk_get has succeeded, so it
should be moved up above the call to clk_put.
The failed_req labels doesn't do anything different than failed_get, so
delete it.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2;
statement S;
@@
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guennadi Liakhovetski [Wed, 1 Jun 2011 07:32:07 +0000 (07:32 +0000)]
ARM: mach-shmobile: add DMAC clock definitions on SH7372
These definitions are needed to let the runtime PM subsystem turn off
DMAC clocks, when it is suspended by the driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Guennadi Liakhovetski [Tue, 31 May 2011 09:25:16 +0000 (09:25 +0000)]
dmaengine: shdma: fix a regression: initialise DMA channels for memcpy
A recent patch has introduced a regression, where repeating a memcpy
DMA test with shdma module unloading between them skips the DMA channel
configuration. Fix this regression by always configuring the channel
during its allocation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Mark Brown [Wed, 1 Jun 2011 10:18:09 +0000 (10:18 +0000)]
net: dm9000: Get the chip in a known good state before enabling interrupts
Currently the DM9000 driver requests the primary interrupt before it
resets the chip and puts it into a known good state. This means that if
the chip is asserting interrupt for some reason we can end up with a
screaming IRQ that the interrupt handler is unable to deal with. Avoid
this by only requesting the interrupt after we've reset the chip so we
know what state it's in.
This started manifesting itself on one of my boards in the past month or
so, I suspect as a result of some core infrastructure changes removing
some form of mitigation against bad behaviour here, even when things boot
it seems that the new code brings the interface up more quickly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Wed, 1 Jun 2011 07:10:10 +0000 (07:10 +0000)]
drivers/net/davinci_emac.c: add missing clk_put
Go to existing error handling code at the end of the function that calls
clk_put.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2;
statement S;
@@
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Greear [Wed, 1 Jun 2011 06:49:10 +0000 (06:49 +0000)]
af-packet: Add flag to distinguish VID 0 from no-vlan.
Currently, user-space cannot determine if a 0 tcp_vlan_tci
means there is no VLAN tag or the VLAN ID was zero.
Add flag to make this explicit. User-space can check for
TP_STATUS_VLAN_VALID || tp_vlan_tci > 0, which will be backwards
compatible. Older could would have just checked for tp_vlan_tci,
so it will work no worse than before.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sjur.brandeland@stericsson.com [Wed, 1 Jun 2011 00:55:37 +0000 (00:55 +0000)]
caif: Fix race when conditionally taking rtnl lock
Take the RTNL lock unconditionally when calling dev_close.
Taking the lock conditionally may cause race conditions.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>