OSDN Git Service
Oliver Smith [Mon, 16 Sep 2013 18:30:57 +0000 (20:30 +0200)]
netfilter: ipset: Fix serious failure in CIDR tracking
This fixes a serious bug affecting all hash types with a net element -
specifically, if a CIDR value is deleted such that none of the same size
exist any more, all larger (less-specific) values will then fail to
match. Adding back any prefix with a CIDR equal to or more specific than
the one deleted will fix it.
Steps to reproduce:
ipset -N test hash:net
ipset -A test 1.1.0.0/16
ipset -A test 2.2.2.0/24
ipset -T test 1.1.1.1 #1.1.1.1 IS in set
ipset -D test 2.2.2.0/24
ipset -T test 1.1.1.1 #1.1.1.1 IS NOT in set
This is due to the fact that the nets counter was unconditionally
decremented prior to the iteration that shifts up the entries. Now, we
first check if there is a proceeding entry and if not, decrement it and
return. Otherwise, we proceed to iterate and then zero the last element,
which, in most cases, will already be zero.
Signed-off-by: Oliver Smith <oliver@8.c.9.b.0.7.4.0.1.0.0.2.ip6.arpa>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Jozsef Kadlecsik [Mon, 16 Sep 2013 18:07:35 +0000 (20:07 +0200)]
netfilter: ipset: Validate the set family and not the set type family at swapping
This closes netfilter bugzilla #843, reported by Quentin Armitage.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Jozsef Kadlecsik [Mon, 16 Sep 2013 18:04:53 +0000 (20:04 +0200)]
netfilter: ipset: Consistent userspace testing with nomatch flag
The "nomatch" commandline flag should invert the matching at testing,
similarly to the --return-nomatch flag of the "set" match of iptables.
Until now it worked with the elements with "nomatch" flag only. From
now on it works with elements without the flag too, i.e:
# ipset n test hash:net
# ipset a test 10.0.0.0/24 nomatch
# ipset t test 10.0.0.1
10.0.0.1 is NOT in set test.
# ipset t test 10.0.0.1 nomatch
10.0.0.1 is in set test.
# ipset a test 192.168.0.0/24
# ipset t test 192.168.0.1
192.168.0.1 is in set test.
# ipset t test 192.168.0.1 nomatch
192.168.0.1 is NOT in set test.
Before the patch the results were
...
# ipset t test 192.168.0.1
192.168.0.1 is in set test.
# ipset t test 192.168.0.1 nomatch
192.168.0.1 is in set test.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Jozsef Kadlecsik [Mon, 16 Sep 2013 18:00:08 +0000 (20:00 +0200)]
netfilter: ipset: Skip really non-first fragments for IPv6 when getting port/protocol
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Phil Oester [Fri, 13 Sep 2013 01:04:16 +0000 (18:04 -0700)]
netfilter: nf_nat_proto_icmpv6:: fix wrong comparison in icmpv6_manip_pkt
In commit
58a317f1 (netfilter: ipv6: add IPv6 NAT support), icmpv6_manip_pkt
was added with an incorrect comparison of ICMP codes to types. This causes
problems when using NAT rules with the --random option. Correct the
comparison.
This closes netfilter bugzilla #851, reported by Alexander Neumann.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Michal Kubeček [Wed, 11 Sep 2013 08:17:27 +0000 (10:17 +0200)]
netfilter: nf_conntrack: use RCU safe kfree for conntrack extensions
Commit
68b80f11 (netfilter: nf_nat: fix RCU races) introduced
RCU protection for freeing extension data when reallocation
moves them to a new location. We need the same protection when
freeing them in nf_ct_ext_free() in order to prevent a
use-after-free by other threads referencing a NAT extension data
via bysource list.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Ariel Elior [Mon, 9 Sep 2013 11:51:27 +0000 (14:51 +0300)]
bnx2x: Fix configuration of doorbell block
As part of VF RSS feature doorbell block was configured not to use dpm, but
a small part of configuration was left out, preventing the driver from sending
tx messages to the device. This patch adds the missing configuration.
Reported-by: Eric Dumazet <eric.dumazet@gmil.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 9 Sep 2013 18:19:09 +0000 (11:19 -0700)]
Merge tag 'xfs-for-linus-v3.12-rc1' of git://oss.sgi.com/xfs/xfs
Pull xfs updates from Ben Myers:
"For 3.12-rc1 there are a number of bugfixes in addition to work to
ease usage of shared code between libxfs and the kernel, the rest of
the work to enable project and group quotas to be used simultaneously,
performance optimisations in the log and the CIL, directory entry file
type support, fixes for log space reservations, some spelling/grammar
cleanups, and the addition of user namespace support.
- introduce readahead to log recovery
- add directory entry file type support
- fix a number of spelling errors in comments
- introduce new Q_XGETQSTATV quotactl for project quotas
- add USER_NS support
- log space reservation rework
- CIL optimisations
- kernel/userspace libxfs rework"
* tag 'xfs-for-linus-v3.12-rc1' of git://oss.sgi.com/xfs/xfs: (112 commits)
xfs: XFS_MOUNT_QUOTA_ALL needed by userspace
xfs: dtype changed xfs_dir2_sfe_put_ino to xfs_dir3_sfe_put_ino
Fix wrong flag ASSERT in xfs_attr_shortform_getvalue
xfs: finish removing IOP_* macros.
xfs: inode log reservations are too small
xfs: check correct status variable for xfs_inobt_get_rec() call
xfs: inode buffers may not be valid during recovery readahead
xfs: check LSN ordering for v5 superblocks during recovery
xfs: btree block LSN escaping to disk uninitialised
XFS: Assertion failed: first <= last && last < BBTOB(bp->b_length), file: fs/xfs/xfs_trans_buf.c, line: 568
xfs: fix bad dquot buffer size in log recovery readahead
xfs: don't account buffer cancellation during log recovery readahead
xfs: check for underflow in xfs_iformat_fork()
xfs: xfs_dir3_sfe_put_ino can be static
xfs: introduce object readahead to log recovery
xfs: Simplify xfs_ail_min() with list_first_entry_or_null()
xfs: Register hotcpu notifier after initialization
xfs: add xfs sb v4 support for dirent filetype field
xfs: Add write support for dirent filetype field
xfs: Add read-only support for dirent filetype field
...
Olof Johansson [Mon, 9 Sep 2013 17:34:23 +0000 (10:34 -0700)]
direct-io: Use return from cmpxchg to decide of assignment happened
Not using the return value can in the generic case be racy, so it's
in general good practice to check the return value instead.
This also resolved the warning caused on ARM and other architectures:
fs/direct-io.c: In function 'sb_init_dio_done_wq':
fs/direct-io.c:557:2: warning: value computed is not used [-Wunused-value]
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: H Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 9 Sep 2013 17:33:19 +0000 (10:33 -0700)]
Merge tag 'for-linus-
20130909' of git://git.infradead.org/linux-mtd
Pull mtd updates from David Woodhouse:
- factor out common code from MTD tests
- nand-gpio cleanup and portability to non-ARM
- m25p80 support for 4-byte addressing chips, other new chips
- pxa3xx cleanup and support for new platforms
- remove obsolete alauda, octagon-5066 drivers
- erase/write support for bcm47xxsflash
- improve detection of ECC requirements for NAND, controller setup
- NFC acceleration support for atmel-nand, read/write via SRAM
- etc
* tag 'for-linus-
20130909' of git://git.infradead.org/linux-mtd: (184 commits)
mtd: chips: Add support for PMC SPI Flash chips in m25p80.c
mtd: ofpart: use for_each_child_of_node() macro
mtd: mtdswap: replace strict_strtoul() with kstrtoul()
mtd cs553x_nand: use kzalloc() instead of memset
mtd: atmel_nand: fix error return code in atmel_nand_probe()
mtd: bcm47xxsflash: writing support
mtd: bcm47xxsflash: implement erasing support
mtd: bcm47xxsflash: convert to module_platform_driver instead of init/exit
mtd: bcm47xxsflash: convert kzalloc to avoid invalid access
mtd: remove alauda driver
mtd: nand: mxc_nand: mark 'const' properly
mtd: maps: cfi_flagadm: add missing __iomem annotation
mtd: spear_smi: add missing __iomem annotation
mtd: r852: Staticize local symbols
mtd: nandsim: Staticize local symbols
mtd: impa7: add missing __iomem annotation
mtd: sm_ftl: Staticize local symbols
mtd: m25p80: add support for mr25h10
mtd: m25p80: make CONFIG_M25PXX_USE_FAST_READ safe to enable
mtd: m25p80: Pass flags through CAT25_INFO macro
...
Linus Torvalds [Mon, 9 Sep 2013 17:32:03 +0000 (10:32 -0700)]
Merge tag 'firewire-updates' of git://git./linux/kernel/git/ieee1394/linux1394
Pull firewire updates from Stefan Richter:
- Fix a regression since 3.2 inclusive: The subsystem workqueue
deadlocked between transaction completion handling and bus reset
handling if the worker pool could not be increased in time.
- janitorial updates
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: Fix deadlock at bus reset
firewire: ohci: Change module_pci_driver to module_init/module_exit
firewire: ohci: beautify some macro definitions
firewire: ohci: change confusing name of a struct member
firewire: core: typecast from gfp_t to bool more safely
firewire: WQ_NON_REENTRANT is meaningless and going away
Linus Torvalds [Mon, 9 Sep 2013 17:26:33 +0000 (10:26 -0700)]
Merge branch 'for-v3.12' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull DMA mapping update from Marek Szyprowski:
"This contains an addition of Device Tree support for reserved memory
regions (Contiguous Memory Allocator is one of the drivers for it) and
changes required by the KVM extensions for PowerPC architectue"
* 'for-v3.12' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: init: add support for reserved memory defined by device tree
drivers: of: add initialization code for dma reserved memory
drivers: of: add function to scan fdt nodes given by path
drivers: dma-contiguous: clean source code and prepare for device tree
Linus Torvalds [Mon, 9 Sep 2013 17:20:54 +0000 (10:20 -0700)]
Merge tag 'virtio-next-for-linus' of git://git./linux/kernel/git/rusty/linux
Pull virtio update from Rusty Russell:
"More console fixes; these are the theoretical ones which didn't get
CC:stable. But for that reason, I did a merge with master partway
through to avoid an unnecessary conflict.
Also: a fun lguest bug turns out if you don't clear the TF flag when
trapping Bad Things happen to the guest kernel as the stack
overflows..."
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_pci: pm: Use CONFIG_PM_SLEEP instead of CONFIG_PM
lguest: fix GPF in guest when using gdb.
lguest: fix guest kernel stack overflow when TF bit set.
lguest: fix BUG_ON() in invalid guest page table.
virtio: console: prevent use-after-free of port name in port unplug
virtio: console: cleanup an error message
virtio: console: fix locking around send_sigio_to_port()
virtio: console: add locking in port unplug path
virtio: console: add locks around buffer removal in port unplug path
tools/lguest: offer VIRTIO_F_ANY_LAYOUT for net device.
virtio tools: add .gitignore
lguest: Point to the right directory for the lguest launcher
Linus Torvalds [Mon, 9 Sep 2013 17:19:36 +0000 (10:19 -0700)]
Merge tag 'vfio-v3.12-rc0' of git://github.com/awilliam/linux-vfio
Pull VFIO update from Alex Williamson:
"VFIO updates include safer default file flags for VFIO device fds, an
external user interface exported to allow other modules to hold
references to VFIO groups, a fix to test for extended config space on
PCIe and PCI-x, and new hot reset interfaces for PCI devices which
allows the user to do PCI bus/slot resets when all of the devices
affected by the reset are owned by the user.
For this last feature, the PCI bus reset interface, I depend on
changes already merged from Bjorn's PCI pull request. I therefore
merged my tree up to commit
cb3e433, which I think was the correct
action, but as Stephen Rothwell noted, I failed to provide a commit
message indicating why the merge was required. Sorry for that.
Thanks, Alex"
* tag 'vfio-v3.12-rc0' of git://github.com/awilliam/linux-vfio:
vfio: fix documentation
vfio-pci: PCI hot reset interface
vfio-pci: Test for extended config space
vfio-pci: Use fdget() rather than eventfd_fget()
vfio: Add O_CLOEXEC flag to vfio device fd
vfio: use get_unused_fd_flags(0) instead of get_unused_fd()
vfio: add external user support
Linus Torvalds [Mon, 9 Sep 2013 16:19:15 +0000 (09:19 -0700)]
Merge tag 'nfs-for-3.12-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
- Fix NFSv4 recovery so that it doesn't recover lost locks in cases
such as lease loss due to a network partition, where doing so may
result in data corruption. Add a kernel parameter to control
choice of legacy behaviour or not.
- Performance improvements when 2 processes are writing to the same
file.
- Flush data to disk when an RPCSEC_GSS session timeout is imminent.
- Implement NFSv4.1 SP4_MACH_CRED state protection to prevent other
NFS clients from being able to manipulate our lease and file
locking state.
- Allow sharing of RPCSEC_GSS caches between different rpc clients.
- Fix the broken NFSv4 security auto-negotiation between client and
server.
- Fix rmdir() to wait for outstanding sillyrename unlinks to complete
- Add a tracepoint framework for debugging NFSv4 state recovery
issues.
- Add tracing to the generic NFS layer.
- Add tracing for the SUNRPC socket connection state.
- Clean up the rpc_pipefs mount/umount event management.
- Merge more patches from Chuck in preparation for NFSv4 migration
support"
* tag 'nfs-for-3.12-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (107 commits)
NFSv4: use mach cred for SECINFO_NO_NAME w/ integrity
NFS: nfs_compare_super shouldn't check the auth flavour unless 'sec=' was set
NFSv4: Allow security autonegotiation for submounts
NFSv4: Disallow security negotiation for lookups when 'sec=' is specified
NFSv4: Fix security auto-negotiation
NFS: Clean up nfs_parse_security_flavors()
NFS: Clean up the auth flavour array mess
NFSv4.1 Use MDS auth flavor for data server connection
NFS: Don't check lock owner compatability unless file is locked (part 2)
NFS: Don't check lock owner compatibility in writes unless file is locked
nfs4: Map NFS4ERR_WRONG_CRED to EPERM
nfs4.1: Add SP4_MACH_CRED write and commit support
nfs4.1: Add SP4_MACH_CRED stateid support
nfs4.1: Add SP4_MACH_CRED secinfo support
nfs4.1: Add SP4_MACH_CRED cleanup support
nfs4.1: Add state protection handler
nfs4.1: Minimal SP4_MACH_CRED implementation
SUNRPC: Replace pointer values with task->tk_pid and rpc_clnt->cl_clid
SUNRPC: Add an identifier for struct rpc_clnt
SUNRPC: Ensure rpc_task->tk_pid is available for tracepoints
...
Linus Torvalds [Mon, 9 Sep 2013 16:18:23 +0000 (09:18 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mszeredi/fuse
Pull fuse bugfixes from Miklos Szeredi:
"Just a bunch of bugfixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: use list_for_each_entry() for list traversing
fuse: readdir: check for slash in names
fuse: hotfix truncate_pagecache() issue
fuse: invalidate inode attributes on xattr modification
fuse: postpone end_page_writeback() in fuse_writepage_locked()
Linus Torvalds [Mon, 9 Sep 2013 16:16:51 +0000 (09:16 -0700)]
Merge tag 'gfs2-merge-window' of git://git./linux/kernel/git/steve/gfs2-3.0-nmw
Pull GFS2 updates from Steven Whitehouse:
"This is possibly the smallest ever set of GFS2 patches for a merge
window. Also, most of them are bug fixes this time.
Two of my three patches (moving gfs2_sync_meta and merging the two
writepage implementations) are clean ups with the third (taking the
glock ref in examine_bucket) being a fix for a difficult to hit race
condition.
The removal of an unused memory barrier is a clean up from Bob
Peterson, and the "spectator" relates to a rarely used mount option.
Ben Marzinski's patch fixes a corner case where the incorrect inode
flags were being set, resulting in incorrect behaviour on fsync"
* tag 'gfs2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-nmw:
GFS2: dirty inode correctly in gfs2_write_end
GFS2: Don't flag consistency error if first mounter is a spectator
GFS2: Remove unnecessary memory barrier
GFS2: Merge ordered and writeback writepage
GFS2: Take glock reference in examine_bucket()
GFS2: Move gfs2_sync_meta to lops.c
Linus Torvalds [Mon, 9 Sep 2013 16:13:22 +0000 (09:13 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
Pull ceph updates from Sage Weil:
"This includes both the first pile of Ceph patches (which I sent to
torvalds@vger, sigh) and a few new patches that add support for
fscache for Ceph. That includes a few fscache core fixes that David
Howells asked go through the Ceph tree. (Thanks go to Milosz Tanski
for putting this feature together)
This first batch of patches (included here) had (has) several
important RBD bug fixes, hole punch support, several different
cleanups in the page cache interactions, improvements in the truncate
code (new truncate mutex to avoid shenanigans with i_mutex), and a
series of fixes in the synchronous striping read/write code.
On top of that is a random collection of small fixes all across the
tree (error code checks and error path cleanup, obsolete wq flags,
etc)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (43 commits)
ceph: use d_invalidate() to invalidate aliases
ceph: remove ceph_lookup_inode()
ceph: trivial buildbot warnings fix
ceph: Do not do invalidate if the filesystem is mounted nofsc
ceph: page still marked private_2
ceph: ceph_readpage_to_fscache didn't check if marked
ceph: clean PgPrivate2 on returning from readpages
ceph: use fscache as a local presisent cache
fscache: Netfs function for cleanup post readpages
FS-Cache: Fix heading in documentation
CacheFiles: Implement interface to check cache consistency
FS-Cache: Add interface to check consistency of a cached object
rbd: fix null dereference in dout
rbd: fix buffer size for writes to images with snapshots
libceph: use pg_num_mask instead of pgp_num_mask for pg.seed calc
rbd: fix I/O error propagation for reads
ceph: use vfs __set_page_dirty_nobuffers interface instead of doing it inside filesystem
ceph: allow sync_read/write return partial successed size of read/write.
ceph: fix bugs about handling short-read for sync read mode.
ceph: remove useless variable revoked_rdcache
...
Linus Torvalds [Mon, 9 Sep 2013 16:09:44 +0000 (09:09 -0700)]
Merge tag 'metag-for-v3.12' of git://git./linux/kernel/git/jhogan/metag
Pull metag architecture changes from James Hogan:
- Device tree updates for TZ1090 GPIO drivers merged via GPIO tree.
- Add driver for ImgTec PDC irqchip as found in TZ1090 SoC.
- Add linux-metag mailing list to MAINTAINERS file.
* tag 'metag-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
irq-imgpdc: add ImgTec PDC irqchip driver
MAINTAINERS: add linux-metag mailing list
metag: tz1090: instantiate gpio-tz1090-pdc
metag: tz1090: select and instantiate gpio-tz1090
metag: tz1090: select and instantiate irq-imgpdc
Linus Torvalds [Mon, 9 Sep 2013 16:05:33 +0000 (09:05 -0700)]
Merge tag 'arc-v3.12-rc1' of git://git./linux/kernel/git/vgupta/arc
Pull ARC changes from Vineet Gupta:
- ARC MM changes:
- preparation for MMUv4 (accomodate new PTE bits, new cmds)
- Rework the ASID allocation algorithm to remove asid-mm reverse map
- Boilerplate code consolidation in Exception Handlers
- Disable FRAME_POINTER for ARC
- Unaligned Access Emulation for Big-Endian from Noam
- Bunch of fixes (udelay, missing accessors) from Mischa
* tag 'arc-v3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: fix new Section mismatches in build (post __cpuinit cleanup)
Kconfig.debug: Add FRAME_POINTER anti-dependency for ARC
ARC: Fix __udelay calculation
ARC: remove console_verbose() from setup_arch()
ARC: Add read*_relaxed to asm/io.h
ARC: Handle un-aligned user space access in BE.
ARC: [ASID] Track ASID allocation cycles/generations
ARC: [ASID] activate_mm() == switch_mm()
ARC: [ASID] get_new_mmu_context() to conditionally allocate new ASID
ARC: [ASID] Refactor the TLB paranoid debug code
ARC: [ASID] Remove legacy/unused debug code
ARC: No need to flush the TLB in early boot
ARC: MMUv4 preps/3 - Abstract out TLB Insert/Delete
ARC: MMUv4 preps/2 - Reshuffle PTE bits
ARC: MMUv4 preps/1 - Fold PTE K/U access flags
ARC: Code cosmetics (Nothing semantical)
ARC: Entry Handler tweaks: Optimize away redundant IRQ_DISABLE_SAVE
ARC: Exception Handlers Code consolidation
ARC: Add some .gitignore entries
Linus Torvalds [Mon, 9 Sep 2013 16:04:46 +0000 (09:04 -0700)]
Merge branch 'for-next' of git://git./linux/kernel/git/gerg/m68knommu
Pull m68knommu fixes from Greg Ungerer:
"Just a small collection of cleanups and fixes this time, no big
changes. The most interresting are to make the m68k and m68knommu
consistently use CONFIG_IOMAP, clean out some unused board config
options and flush the cache on signal stack creation"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: remove 16 unused boards in Kconfig.machine
m68k: define 'VM_DATA_DEFAULT_FLAGS' no matter whether has 'NOMMU' or not
m68knommu: user generic iomap to support ioread*/iowrite*
m68k/coldfire: flush cache when creating the signal stack frame
m68knommu: Mark functions only called from setup_arch() __init
Linus Torvalds [Mon, 9 Sep 2013 16:03:46 +0000 (09:03 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/rw/uml
Pull UML updates from Richard Weinberger:
"This pile contains mostly fixes and improvements for issues identified
by Richard W M Jones while adding UML as backend to libguestfs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Add irq chip um/mask handlers
um: prctl: Do not include linux/ptrace.h
um: Run UML in it's own session.
um: Cleanup SIGTERM handling
um: ubd: Introduce submit_request()
um: ubd: Add REQ_FLUSH suppport
um: Implement probe_kernel_read()
um: hostfs: Fix writeback
Linus Torvalds [Mon, 9 Sep 2013 01:13:49 +0000 (18:13 -0700)]
vfs: fix dentry RCU to refcounting possibly sleeping dput()
This is the fix that the last two commits indirectly led up to - making
sure that we don't call dput() in a bad context on the dentries we've
looked up in RCU mode after the sequence count validation fails.
This basically expands d_rcu_to_refcount() into the callers, and then
fixes the callers to delay the dput() in the failure case until _after_
we've dropped all locks and are no longer in an RCU-locked region.
The case of 'complete_walk()' was trivial, since its failure case did
the unlock_rcu_walk() directly after the call to d_rcu_to_refcount(),
and as such that is just a pure expansion of the function with a trivial
movement of the resulting dput() to after 'unlock_rcu_walk()'.
In contrast, the unlazy_walk() case was much more complicated, because
not only does convert two different dentries from RCU to be reference
counted, but it used to not call unlock_rcu_walk() at all, and instead
just returned an error and let the caller clean everything up in
"terminate_walk()".
Happily, one of the dentries in question (called "parent" inside
unlazy_walk()) is the dentry of "nd->path", which terminate_walk() wants
a refcount to anyway for the non-RCU case.
So what the new and improved unlazy_walk() does is to first turn that
dentry into a refcounted one, and once that is set up, the error cases
can continue to use the terminate_walk() helper for cleanup, but for the
non-RCU case. Which makes it possible to drop out of RCU mode if we
actually hit the sequence number failure case.
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aaron Lu [Mon, 9 Sep 2013 00:27:12 +0000 (09:57 +0930)]
virtio_pci: pm: Use CONFIG_PM_SLEEP instead of CONFIG_PM
The virtio_pci_freeze/restore are defined under CONFIG_PM but is used
by SET_SYSTEM_SLEEP_PM_OPS macro, which is defined under
CONFIG_PM_SLEEP. So if CONFIG_PM_SLEEP is not cofigured but
CONFIG_PM_RUNTIME is, the following warning message appeared:
drivers/virtio/virtio_pci.c:770:12: warning: ‘virtio_pci_freeze’ defined but not used [-Wunused-function]
static int virtio_pci_freeze(struct device *dev)
^
drivers/virtio/virtio_pci.c:790:12: warning: ‘virtio_pci_restore’ defined but not used [-Wunused-function]
static int virtio_pci_restore(struct device *dev)
^
Fix it by changing CONFIG_PM to CONFIG_PM_SLEEP.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Linus Torvalds [Sun, 8 Sep 2013 20:46:52 +0000 (13:46 -0700)]
vfs: use lockred "dead" flag to mark unrecoverably dead dentries
This simplifies the RCU to refcounting code in particular.
I was originally intending to leave this for later, but walking through
all the dput() logic (see previous commit), I realized that the dput()
"might_sleep()" check was misleadingly weak. And I removed it as
misleading, both for performance profiling and for debugging.
However, the might_sleep() debugging case is actually true: the final
dput() can indeed sleep, if the inode of the dentry that you are
releasing ends up sleeping at iput time (see dentry_iput()). So the
problem with the might_sleep() in dput() wasn't that it wasn't true, it
was that it wasn't actually testing and triggering on the interesting
case.
In particular, just about *any* dput() can indeed sleep, if you happen
to race with another thread deleting the file in question, and you then
lose the race to the be the last dput() for that file. But because it's
a very rare race, the debugging code would never trigger it in practice.
Why is this problematic? The new d_rcu_to_refcount() (see commit
15570086b590: "vfs: reimplement d_rcu_to_refcount() using
lockref_get_or_lock()") does a dput() for the failure case, and it does
it under the RCU lock. So potentially sleeping really is a bug.
But there's no way I'm going to fix this with the previous complicated
"lockref_get_or_lock()" interface. And rather than revert to the old
and crufty nested dentry locking code (which did get this right by
delaying the reference count updates until they were verified to be
safe), let's make forward progress.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 8 Sep 2013 20:26:18 +0000 (13:26 -0700)]
vfs: reorganize dput() memory accesses
This is me being a bit OCD after all the dentry optimization work this
merge window: profiles end up showing 'dput()' as a rather expensive
operation, and there were two unrelated bad reasons for that.
The first reason was reading d_lockref.count for debugging purposes,
which touches the lockref cacheline (for reads) before really need to.
More importantly, the debugging test in question is _wrong_, and has
hidden bugs. It's true that we can only sleep when the count goes down
to zero, but the test as-is hides the much more subtle bug that happens
if we race with somebody else deleting the file.
Anyway we _will_ touch that cacheline, but let's do it for a write and
in the right routine (ie in "lockref_put_or_lock()") which annotates the
costs better. So remove the misleading debug code.
The other was an unnecessary access to the cacheline that contains the
d_lru list, just to check whether we already were on the LRU list or
not. This is exactly what we have d_flags for, so that we can avoid
touching extra cache lines for the common case. So just add another bit
for "is this dentry on the LRU".
Finally, mark the tests properly likely/unlikely, so that the common
fast-paths are dense in the instruction stream.
This makes the profiles look much saner.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 8 Sep 2013 03:19:02 +0000 (20:19 -0700)]
Merge git://git.infradead.org/users/willy/linux-nvme
Pull NVM Express driver update from Matthew Wilcox.
* git://git.infradead.org/users/willy/linux-nvme:
NVMe: Merge issue on character device bring-up
NVMe: Handle ioremap failure
NVMe: Add pci suspend/resume driver callbacks
NVMe: Use normal shutdown
NVMe: Separate controller init from disk discovery
NVMe: Separate queue alloc/free from create/delete
NVMe: Group pci related actions in functions
NVMe: Disk stats for read/write commands only
NVMe: Bring up cdev on set feature failure
NVMe: Fix checkpatch issues
NVMe: Namespace IDs are unsigned
NVMe: Update nvme_id_power_state with latest spec
NVMe: Split header file into user-visible and kernel-visible pieces
NVMe: Call nvme_process_cq from submission path
NVMe: Remove "process_cq did something" message
NVMe: Return correct value from interrupt handler
NVMe: Disk IO statistics
NVMe: Restructure MSI / MSI-X setup
NVMe: Use kzalloc instead of kmalloc+memset
Linus Torvalds [Sun, 8 Sep 2013 03:17:44 +0000 (20:17 -0700)]
Merge tag 'ntb-3.12' of git://github.com/jonmason/ntb
Pull NTB (non-transparent bridge) updates from Jon Mason:
"NTB driver bug fixes to address issues in NTB-RP enablement, spad,
debugfs, and USD/DSD identification.
Add a workaround on Xeon NTB devices for b2bdoorbell errata. Also,
add new NTB driver features to support 32bit x86, DMA engine support,
and NTB-RP support.
Finally, a few clean-ups and update to MAINTAINERS for the NTB git
tree and wiki location"
* tag 'ntb-3.12' of git://github.com/jonmason/ntb:
ntb: clean up unnecessary MSI/MSI-X capability find
MAINTAINERS: Add Website and Git Tree for NTB
NTB: Update Version
NTB: Comment Fix
NTB: Remove unused variable
NTB: Remove References of non-B2B BWD HW
NTB: NTB-RP support
NTB: Rename Variables for NTB-RP
NTB: Use DMA Engine to Transmit and Receive
NTB: Enable 32bit Support
NTB: Update Device IDs
NTB: BWD Link Recovery
NTB: Xeon Errata Workaround
NTB: Correct debugfs to work with more than 1 NTB Device
NTB: Correct USD/DSD Identification
NTB: Correct Number of Scratch Pad Registers
NTB: Add Error Handling in ntb_device_setup
Linus Torvalds [Sun, 8 Sep 2013 03:14:19 +0000 (20:14 -0700)]
Merge tag 'mfd-3.12-1' of git://git./linux/kernel/git/sameo/mfd-next
Pull MFD (multi-function device) updates from Samuel Ortiz:
"For the 3.12 merge window we have one new driver for the DA9063 PMIC
from Dialog Semiconductor.
Besides that driver we also have:
- Device tree support for the s2mps11 driver
- More devm_* conversion for the pm8921, max89xx, menelaus, tps65010,
wl1273 and pcf50633-adc drivers.
- A conversion to threaded IRQ and IRQ domain for the twl6030 driver.
- A fairly big update for the rtsx driver: Better power saving
support, better vendor settings handling, and a few fixes.
- Support for a couple more boards (COMe-bHL6 and COMe-cTH6) for the
Kontron driver.
- A conversion to the dev_get_platdata() API for all MFD drivers.
- A removal of non-DT (legacy) support for the twl6040 driver.
- A few fixes and additions (Mic detect level) to the wm5110 register
tables.
- Regmap support for the davinci_voicecodec driver.
- The usual bunch of minor cleanups and janitorial fixes"
* tag 'mfd-3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (81 commits)
mfd: ucb1x00-core: Rewrite ucb1x00_add_dev()
mfd: ab8500-debugfs: Apply a check for -ENOMEM after allocating memory for event name
mfd: ab8500-debugfs: Apply a check for -ENOMEM after allocating memory for sysfs
mfd: timberdale: Use module_pci_driver
mfd: timberdale: Remove redundant break
mfd: timberdale: Staticize local variables
mfd: ab8500-debugfs: Staticize local variables
mfd: db8500-prcmu: Staticize clk_mgt
mfd: db8500-prcmu: Use ANSI function declaration
mfd: omap-usb-host: Staticize usbhs_driver_name
mfd: 88pm805: Fix potential NULL pdata dereference
mfd: 88pm800: Fix potential NULL pdata dereference
mfd: twl6040: Use regmap for register cache
mfd: davinci_voicecodec: Provide a regmap for register I/O
mfd: davinci_voicecodec: Remove unused read and write functions
mmc: memstick: rtsx: Modify copyright comments
mmc: rtsx: Clear SD_CLK toggle enable bit if switching voltage fail
mfd: mmc: rtsx: Change default tx phase
mfd: pcf50633-adc: Use devm_*() functions
mfd: rtsx: Copyright modifications
...
Linus Torvalds [Sun, 8 Sep 2013 02:47:35 +0000 (19:47 -0700)]
Merge branch 'misc' of git://git./linux/kernel/git/mmarek/kbuild
Pull misc kbuild updates from Michal Marek:
"In the kbuild misc branch, I have:
- make rpm-pkg updates, most importantly the rpm package now calls
/sbin/installkernel
- make deb-pkg: debuginfo split, correct kernel image path for
parisc, mips and powerpc and a couple more minor fixes
- New coccinelle check"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scripts/checkkconfigsymbols.sh: replace echo -e with printf
Provide version number for Debian firmware package
coccinelle: replace 0/1 with false/true in functions returning bool
deb-pkg: add a hook argument to match debian hooks parameters
deb-pkg: fix installed image path on parisc, mips and powerpc
deb-pkg: split debug symbols in their own package
deb-pkg: use KCONFIG_CONFIG instead of .config file directly
rpm-pkg: add generation of kernel-devel
rpm-pkg: install firmware files in kernel relative directory
rpm-pkg: add %post section to create initramfs and grub hooks
Linus Torvalds [Sun, 8 Sep 2013 02:46:50 +0000 (19:46 -0700)]
Merge branch 'kbuild' of git://git./linux/kernel/git/mmarek/kbuild
Pull kbuild update from Michal Marek:
"Only these two commits are in the kbuild branch this time:
- Using filechk for include/config/kernel.release
- Cleanup in scripts/sortextable.c"
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Do not overwrite include/config/kernel.release needlessly
scripts: remove unused function in sortextable.c
Linus Torvalds [Sat, 7 Sep 2013 22:49:18 +0000 (15:49 -0700)]
lockref: add ability to mark lockrefs "dead"
The only actual current lockref user (dcache) uses zero reference counts
even for perfectly live dentries, because it's a cache: there may not be
any users, but that doesn't mean that we want to throw away the dentry.
At the same time, the dentry cache does have a notion of a truly "dead"
dentry that we must not even increment the reference count of, because
we have pruned it and it is not valid.
Currently that distinction is not visible in the lockref itself, and the
dentry cache validation uses "lockref_get_or_lock()" to either get a new
reference to a dentry that already had existing references (and thus
cannot be dead), or get the dentry lock so that we can then verify the
dentry and increment the reference count under the lock if that
verification was successful.
That's all somewhat complicated.
This adds the concept of being "dead" to the lockref itself, by simply
using a count that is negative. This allows a usage scenario where we
can increment the refcount of a dentry without having to validate it,
and pushing the special "we killed it" case into the lockref code.
The dentry code itself doesn't actually use this yet, and it's probably
too late in the merge window to do that code (the dentry_kill() code
with its "should I decrement the count" logic really is pretty complex
code), but let's introduce the concept at the lockref level now.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Weston Andros Adamson [Wed, 4 Sep 2013 16:13:19 +0000 (12:13 -0400)]
NFSv4: use mach cred for SECINFO_NO_NAME w/ integrity
Commit
97431204ea005ec8070ac94bc3251e836daa7ca7 introduced a regression
that causes SECINFO_NO_NAME to fail without sending an RPC if:
1) the nfs_client's rpc_client is using krb5i/p (now tried by default)
2) the current user doesn't have valid kerberos credentials
This situation is quite common - as of now a sec=sys mount would use
krb5i for the nfs_client's rpc_client and a user would hardly be faulted
for not having run kinit.
The solution is to use the machine cred when trying to use an integrity
protected auth flavor for SECINFO_NO_NAME.
Older servers may not support using the machine cred or an integrity
protected auth flavor for SECINFO_NO_NAME in every circumstance, so we fall
back to using the user's cred and the filesystem's auth flavor in this case.
We run into another problem when running against linux nfs servers -
they return NFS4ERR_WRONGSEC when using integrity auth flavor (unless the
mount is also that flavor) even though that is not a valid error for
SECINFO*. Even though it's against spec, handle WRONGSEC errors on
SECINFO_NO_NAME by falling back to using the user cred and the
filesystem's auth flavor.
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Sat, 7 Sep 2013 22:28:10 +0000 (18:28 -0400)]
NFS: nfs_compare_super shouldn't check the auth flavour unless 'sec=' was set
Also don't worry about obsolete mount flags...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Linus Torvalds [Sat, 7 Sep 2013 22:30:29 +0000 (15:30 -0700)]
lockref: fix docbook argument names
The code got rewritten, but the comments got copied as-is from older
versions, and as a result the argument name in the comment didn't
actually match the code any more.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trond Myklebust [Sat, 7 Sep 2013 20:01:07 +0000 (16:01 -0400)]
NFSv4: Allow security autonegotiation for submounts
In cases where the parent super block was not mounted with a 'sec=' line,
allow autonegotiation of security for the submounts.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Sat, 7 Sep 2013 21:49:05 +0000 (17:49 -0400)]
NFSv4: Disallow security negotiation for lookups when 'sec=' is specified
Ensure that nfs4_proc_lookup_common respects the NFS_MOUNT_SECFLAVOUR
flag.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Linus Torvalds [Sat, 7 Sep 2013 21:36:57 +0000 (14:36 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull vfs pile 2 (of many) from Al Viro:
"Mostly Miklos' series this time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
constify dcache.c inlined helpers where possible
fuse: drop dentry on failed revalidate
fuse: clean up return in fuse_dentry_revalidate()
fuse: use d_materialise_unique()
sysfs: use check_submounts_and_drop()
nfs: use check_submounts_and_drop()
gfs2: use check_submounts_and_drop()
afs: use check_submounts_and_drop()
vfs: check unlinked ancestors before mount
vfs: check submounts and drop atomically
vfs: add d_walk()
vfs: restructure d_genocide()
Linus Torvalds [Sat, 7 Sep 2013 21:35:32 +0000 (14:35 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ebiederm/user-namespace
Pull namespace changes from Eric Biederman:
"This is an assorted mishmash of small cleanups, enhancements and bug
fixes.
The major theme is user namespace mount restrictions. nsown_capable
is killed as it encourages not thinking about details that need to be
considered. A very hard to hit pid namespace exiting bug was finally
tracked and fixed. A couple of cleanups to the basic namespace
infrastructure.
Finally there is an enhancement that makes per user namespace
capabilities usable as capabilities, and an enhancement that allows
the per userns root to nice other processes in the user namespace"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
userns: Kill nsown_capable it makes the wrong thing easy
capabilities: allow nice if we are privileged
pidns: Don't have unshare(CLONE_NEWPID) imply CLONE_THREAD
userns: Allow PR_CAPBSET_DROP in a user namespace.
namespaces: Simplify copy_namespaces so it is clear what is going on.
pidns: Fix hang in zap_pid_ns_processes by sending a potentially extra wakeup
sysfs: Restrict mounting sysfs
userns: Better restrictions on when proc and sysfs can be mounted
vfs: Don't copy mount bind mounts of /proc/<pid>/ns/mnt between namespaces
kernel/nsproxy.c: Improving a snippet of code.
proc: Restrict mounting the proc filesystem
vfs: Lock in place mounts from more privileged users
Linus Torvalds [Sat, 7 Sep 2013 21:34:07 +0000 (14:34 -0700)]
Merge branch 'next' of git://git./linux/kernel/git/jmorris/linux-security
Pull security subsystem updates from James Morris:
"Nothing major for this kernel, just maintenance updates"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (21 commits)
apparmor: add the ability to report a sha1 hash of loaded policy
apparmor: export set of capabilities supported by the apparmor module
apparmor: add the profile introspection file to interface
apparmor: add an optional profile attachment string for profiles
apparmor: add interface files for profiles and namespaces
apparmor: allow setting any profile into the unconfined state
apparmor: make free_profile available outside of policy.c
apparmor: rework namespace free path
apparmor: update how unconfined is handled
apparmor: change how profile replacement update is done
apparmor: convert profile lists to RCU based locking
apparmor: provide base for multiple profiles to be replaced at once
apparmor: add a features/policy dir to interface
apparmor: enable users to query whether apparmor is enabled
apparmor: remove minimum size check for vmalloc()
Smack: parse multiple rules per write to load2, up to PAGE_SIZE-1 bytes
Smack: network label match fix
security: smack: add a hash table to quicken smk_find_entry()
security: smack: fix memleak in smk_write_rules_list()
xattr: Constify ->name member of "struct xattr".
...
Linus Torvalds [Sat, 7 Sep 2013 21:31:18 +0000 (14:31 -0700)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto update from Herbert Xu:
"Here is the crypto update for 3.12:
- Added MODULE_SOFTDEP to allow pre-loading of modules.
- Reinstated crct10dif driver using the module softdep feature.
- Allow via rng driver to be auto-loaded.
- Split large input data when necessary in nx.
- Handle zero length messages correctly for GCM/XCBC in nx.
- Handle SHA-2 chunks bigger than block size properly in nx.
- Handle unaligned lengths in omap-aes.
- Added SHA384/SHA512 to omap-sham.
- Added OMAP5/AM43XX SHAM support.
- Added OMAP4 TRNG support.
- Misc fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (66 commits)
Reinstate "crypto: crct10dif - Wrap crc_t10dif function all to use crypto transform framework"
hwrng: via - Add MODULE_DEVICE_TABLE
crypto: fcrypt - Fix bitoperation for compilation with clang
crypto: nx - fix SHA-2 for chunks bigger than block size
crypto: nx - fix GCM for zero length messages
crypto: nx - fix XCBC for zero length messages
crypto: nx - fix limits to sg lists for AES-CCM
crypto: nx - fix limits to sg lists for AES-XCBC
crypto: nx - fix limits to sg lists for AES-GCM
crypto: nx - fix limits to sg lists for AES-CTR
crypto: nx - fix limits to sg lists for AES-CBC
crypto: nx - fix limits to sg lists for AES-ECB
crypto: nx - add offset to nx_build_sg_lists()
padata - Register hotcpu notifier after initialization
padata - share code between CPU_ONLINE and CPU_DOWN_FAILED, same to CPU_DOWN_PREPARE and CPU_UP_CANCELED
hwrng: omap - reorder OMAP TRNG driver code
crypto: omap-sham - correct dma burst size
crypto: omap-sham - Enable Polling mode if DMA fails
crypto: tegra-aes - bitwise vs logical and
crypto: sahara - checking the wrong variable
...
Linus Torvalds [Sat, 7 Sep 2013 21:27:46 +0000 (14:27 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"A quick set of fixes, some to deal with fallout from yesterday's
net-next merge.
1) Fix compilation of bnx2x driver with CONFIG_BNX2X_SRIOV disabled,
from Dmitry Kravkov.
2) Fix a bnx2x regression caused by one of Dave Jones's mistaken
braces changes, from Eilon Greenstein.
3) Add some protective filtering in the netlink tap code, from Daniel
Borkmann.
4) Fix TCP congestion window growth regression after timeouts, from
Yuchung Cheng.
5) Correctly adjust TCP's rcv_ssthresh for out of order packets, from
Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
tcp: properly increase rcv_ssthresh for ofo packets
net: add documentation for BQL helpers
mlx5: remove unused MLX5_DEBUG param in Kconfig
bnx2x: Restore a call to config_init
bnx2x: fix broken compilation with CONFIG_BNX2X_SRIOV is not set
tcp: fix no cwnd growth after timeout
net: netlink: filter particular protocols from analyzers
Trond Myklebust [Sat, 7 Sep 2013 16:58:57 +0000 (12:58 -0400)]
NFSv4: Fix security auto-negotiation
NFSv4 security auto-negotiation has been broken since
commit
4580a92d44e2b21c2254fa5fef0f1bfb43c82318 (NFS:
Use server-recommended security flavor by default (NFSv3))
because nfs4_try_mount() will automatically select AUTH_SYS
if it sees no auth flavours.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Chuck Lever <chuck.lever@oracle.com>
Trond Myklebust [Sat, 7 Sep 2013 18:09:52 +0000 (14:09 -0400)]
NFS: Clean up nfs_parse_security_flavors()
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Sat, 7 Sep 2013 17:26:57 +0000 (13:26 -0400)]
NFS: Clean up the auth flavour array mess
What is the point of having a 'auth_flavor_len' field, if it is
always set to 1, and can't be used to determine if the user has
selected an auth flavour?
This cleanup goes back to using auth_flavor_len for its original
intended purpose, and gets rid of the ad-hoc replacements.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Linus Torvalds [Sat, 7 Sep 2013 17:54:19 +0000 (10:54 -0700)]
Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/jdelvare/staging
Pull hwmon fixes from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (emc6w201) Do not declare enum variable
hwmon: (w83792d) Update module author
Linus Torvalds [Sat, 7 Sep 2013 17:53:00 +0000 (10:53 -0700)]
Merge tag 'gpio-v3.12-1' of git://git./linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v3.12 series:
- A new driver for the TZ1090 PDC which is used on the metag
architecture.
- A new driver for the Kontron ETX or COMexpress GPIO block. This is
found on some ETX x86 devices.
- A new driver for the Fintek Super-I/O chips, used on some x86
boards.
- Added device tree probing on a few select GPIO blocks.
- Drop the Exynos support from the Samsung GPIO driver.
The Samsung maintainers have moved over to use the modernized pin
control driver to provide GPIO for the modern platforms instead.
- The usual bunch of non-critical fixes and cleanups"
* tag 'gpio-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (36 commits)
gpio: return -ENOTSUPP if debounce cannot be set
gpio: improve error path in gpiolib
gpio: add GPIO support for F71882FG and
F71889F
of: add vendor prefix for Microchip Technology Inc
gpio: mcp23s08: rename the device tree property
gpio: samsung: Drop support for Exynos SoCs
gpio: pcf857x: Remove pdata argument to pcf857x_irq_domain_init()
gpio: pcf857x: Sort headers alphabetically
gpio: max7301: Reverting "Do not force SPI speed when using OF Platform"
gpio: Fix bit masking in Kontron PLD GPIO driver
gpio: pca953x: fix gpio input on gpio offsets >= 8
drivers/gpio: simplify use of devm_ioremap_resource
drivers/gpio/gpio-omap.c: convert comma to semicolon
gpio-lynxpoint: Fix warning about unbalanced pm_runtime_enable
gpio: Fix platform driver name in Kontron PLD GPIO driver
gpio: adnp: Fix segfault if request_threaded_irq fails
gpio: msm: Staticize local variable 'msm_gpio'
gpio: gpiolib-of.c: make error message more meaningful by adding the node name and index
gpio: use dev_get_platdata()
gpio/mxc: add chained_irq_enter/exit() to mx2_gpio_irq_handler
...
Linus Torvalds [Sat, 7 Sep 2013 17:38:46 +0000 (10:38 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"A new driver for slidebar on Ideapad laptops and a bunch of assorted
driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (32 commits)
Input: add SYN_MAX and SYN_CNT constants
Input: max11801_ts - convert to devm
Input: egalax-ts - fix typo and improve text
Input: MAINTAINERS - change maintainer for cyttsp driver
Input: cyttsp4 - kill 'defined but not used' compiler warnings
Input: add driver for slidebar on Lenovo IdeaPad laptops
Input: omap-keypad - set up irq type from DT
Input: omap-keypad - enable wakeup capability for keypad.
Input: omap-keypad - clear interrupts on open
Input: omap-keypad - convert to threaded IRQ
Input: omap-keypad - use bitfiled instead of hardcoded values
Input: cyttsp4 - remove useless NULL test from cyttsp4_watchdog_timer()
Input: wacom - fix error return code in wacom_probe()
Input: as5011 - fix error return code in as5011_probe()
Input: keyboard, serio - simplify use of devm_ioremap_resource
Input: tegra-kbc - simplify use of devm_ioremap_resource
Input: htcpen - fix incorrect placement of __initdata
Input: qt1070 - add power management ops
Input: wistron_btns - add MODULE_DEVICE_TABLE
Input: wistron_btns - mark the Medion MD96500 keymap as tested
...
Linus Torvalds [Sat, 7 Sep 2013 16:48:41 +0000 (09:48 -0700)]
Revert "Input: introduce BTN/ABS bits for drums and guitars"
This reverts commits
61e00655e9cb,
73f8645db191 and
8e22ecb603c8:
"Input: introduce BTN/ABS bits for drums and guitars"
"HID: wiimote: add support for Guitar-Hero drums"
"HID: wiimote: add support for Guitar-Hero guitars"
The extra new ABS_xx values resulted in ABS_MAX no longer being a
power-of-two, which broke the comparison logic. It also caused the
ioctl numbers to overflow into the next byte, causing problems for that.
We'll try again for 3.13.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Richard Weinberger [Mon, 2 Sep 2013 20:49:22 +0000 (22:49 +0200)]
um: Add irq chip um/mask handlers
These handlers are not optional and need in our case
dummy implementions to avoid NULL pointer bugs within
the irq core code.
Reported-and-tested-by: Toralf Foester <toralf.foerster@gmx.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Fri, 23 Aug 2013 11:37:49 +0000 (13:37 +0200)]
um: prctl: Do not include linux/ptrace.h
On recent toolchains we hit:
In file included from arch/x86/um/os-Linux/prctl.c:7:0:
/usr/include/linux/ptrace.h:58:8: error: redefinition of ‘struct
ptrace_peeksiginfo_args’ struct ptrace_peeksiginfo_args {
^
In file included from arch/x86/um/os-Linux/prctl.c:6:0:
/usr/include/sys/ptrace.h:191:8: note: originally defined here
struct ptrace_peeksiginfo_args
^
make[2]: *** [arch/x86/um/os-Linux/prctl.o] Error 1
make[1]: *** [arch/x86/um/os-Linux] Error 2
make: *** [arch/x86/um] Error 2
The solution is not to include linux/ptrace.h and obtain
the arch specific ptrace command from asm/ptrace.h.
Reported-and-tested-by: David Oberhollenzer <david.oberhollenzer@tele2.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Sun, 18 Aug 2013 11:30:09 +0000 (13:30 +0200)]
um: Run UML in it's own session.
If UML is not run by a shell it can happen that UML
will kill unrelated proceses upon a fatal exit because
it issues a kill(0, ...).
To prevent such oddities we create a new session in main().
Reported-and-tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Sun, 18 Aug 2013 11:30:08 +0000 (13:30 +0200)]
um: Cleanup SIGTERM handling
Richard reported that some UML processes survive if the UML
main process receives a SIGTERM.
This issue was caused by a wrongly placed signal(SIGTERM, SIG_DFL)
in init_new_thread_signals().
It disabled the UML exit handler accidently for some processes.
The correct solution is to disable the fatal handler for all
UML helper threads/processes.
Such that last_ditch_exit() does not get called multiple times
and all processes can exit due to SIGTERM.
Reported-and-tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Sun, 18 Aug 2013 11:30:07 +0000 (13:30 +0200)]
um: ubd: Introduce submit_request()
Just a clean-up patch to remove the open coded
variants and to ensure that all requests are submitted the
same way.
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Sun, 18 Aug 2013 11:30:06 +0000 (13:30 +0200)]
um: ubd: Add REQ_FLUSH suppport
UML's block device driver does not support write barriers,
to support this this patch adds REQ_FLUSH suppport.
Every time the block layer sends a REQ_FLUSH we fsync() now
our backing file to guarantee data consistency.
Reported-and-tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Sat, 17 Aug 2013 16:46:00 +0000 (18:46 +0200)]
um: Implement probe_kernel_read()
UML needs it's own probe_kernel_read() to handle kernel
mode faults correctly.
The implementation uses mincore() on the host side to detect
whether a page is owned by the UML kernel process.
This fixes also a possible crash when sysrq-t is used.
Starting with 3.10 sysrq-t calls probe_kernel_read() to
read details from the kernel workers. As kernel worker are
completely async pointers may turn NULL while reading them.
Cc: <stian@nixia.no>
Cc: <tj@kernel.org>
Cc: <stable@vger.kernel.org> # 3.10.x
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Sun, 4 Aug 2013 17:23:51 +0000 (17:23 +0000)]
um: hostfs: Fix writeback
We have to implement ->release() and trigger writeback from it.
Otherwise we might lose dirty pages at munmap().
Signed-off-by: Richard Weinberger <richard@nod.at>
Dmitry Torokhov [Sat, 7 Sep 2013 03:23:44 +0000 (20:23 -0700)]
Merge branch 'next' into for-linus
Merge first round of changes for 3.12 merge window.
Herbert Xu [Sat, 7 Sep 2013 02:56:26 +0000 (12:56 +1000)]
Reinstate "crypto: crct10dif - Wrap crc_t10dif function all to use crypto transform framework"
This patch reinstates commits
67822649d7305caf3dd50ed46c27b99c94eff996
39761214eefc6b070f29402aa1165f24d789b3f7
0b95a7f85718adcbba36407ef88bba0a7379ed03
31d939625a9a20b1badd2d4e6bf6fd39fa523405
2d31e518a42828df7877bca23a958627d60408bc
Now that module softdeps are in the kernel we can use that to resolve
the boot issue which cause the revert.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert Xu [Sat, 7 Sep 2013 02:53:35 +0000 (12:53 +1000)]
Merge git://git./linux/kernel/git/torvalds/linux
Merge upstream tree in order to reinstate crct10dif.
Linus Torvalds [Fri, 6 Sep 2013 20:34:43 +0000 (13:34 -0700)]
Merge tag 'boards-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"Board updates for 3.12. Again, a bit of domain overlap with SoC and
DT branches, but most of this is around legacy code and board support.
We've found that platform maintainers have a hard time separating all
of these out and might move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and
clocksource setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas
Lager.
- New backlight drivers for backlights used on Renesas shmobile
platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for
others in the same mach directory. More in 3.13"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
mmc: sdhci-bcm-kona: Staticize sdhci_bcm_kona_card_event
mmc: sdhci-bcm-kona: Remove unneeded version.h inclusion
ARM: bcm: Make secure API call optional
ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
ARM: bcm: Rename board_bcm
mmc: sdhci-bcm-kona: make linker-section warning go away
ARM: tegra: defconfig updates
ARM: dove: add initial DT file for Globalscale D2Plug
ARM: dove: add GPIO IR receiver node to SolidRun CuBox
ARM: dove: add common pinmux functions to DT
ARM: dove: add cpu device tree node
ARM: dove: update dove_defconfig with SI5351, PCI, and xHCI
arch/arm/mach-kirkwood: Avoid using ARRAY_AND_SIZE(e) as a function argument
ARM: kirkwood: fix DT building and update defconfig
ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code
ARM: configs: disable DEBUG_LL in bcm_defconfig
ARM: bcm281xx: Board specific reboot code
ARM bcm281xx: Turn on socket & network support.
ARM: bcm281xx: Turn on L2 cache.
...
Linus Torvalds [Fri, 6 Sep 2013 20:30:06 +0000 (13:30 -0700)]
Merge tag 'soc-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
Keith Busch [Thu, 5 Sep 2013 20:45:07 +0000 (14:45 -0600)]
NVMe: Merge issue on character device bring-up
A recent patch made it possible to bring up the character handle when the
device is responsive but not accepting a set-features command. Another
recent patch moved the initialization that requires we move where the
checks for this condition occur. This patch merges these two ideas so
it works much as before.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Linus Torvalds [Fri, 6 Sep 2013 20:26:27 +0000 (13:26 -0700)]
Merge tag 'dt-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on
various platforms as support gets added. Some of the bigger changes
are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for
4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (177 commits)
dts: Rename DW APB timer compatible strings
dts: Deprecate ALTR as a vendor prefix
of: add vendor prefix for Altera Corp.
ARM: at91/dt: sam9x5ek: add sound configuration
ARM: at91/dt: sam9x5ek: enable SSC
ARM: at91/dt: sam9x5ek: add WM8731 codec
ARM: at91/dt: sam9x5: add SSC DMA parameters
ARM: at91/dt: add at91rm9200 PQFP package version
ARM: at91: at91rm9200: set default mmc0 pinctrl-names
ARM: at91: at91sam9n12: correct pin number of gpio-key
ARM: at91: at91sam9n12: add qt1070 support
ARM: at91: at91sam9n12: add pinctrl of TWI
ARM: at91: Add PMU support for sama5d3
ARM: at91: at91sam9260: add missing pinctrl-names on mmc
ARM: tegra: configure power off for Dalmore
ARM: DT: binding fixup to align with vendor-prefixes.txt (DT)
ARM: dts: add sdio blocks to bcm28155-ap board
ARM: dts: align sdio numbers to HW definition
ARM: sun7i: Add Olimex A20-Olinuxino-Micro support
ARM: sun7i: Add Allwinner A20 DTSI
...
Linus Torvalds [Fri, 6 Sep 2013 20:21:16 +0000 (13:21 -0700)]
Merge tag 'cleanup-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer
API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM
driver and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM
platform code for include changes so we took it through our tree"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: OMAP2+: Add back the define for AM33XX_RST_GLOBAL_WARM_SW_MASK
gpio: (gpio-pca953x) move header to linux/platform_data/
arm: zynq: hotplug: Remove unreachable code
ARM: SAMSUNG: Remove unnecessary exynos4_default_sdhci*()
tegra: simplify use of devm_ioremap_resource
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
ARM: mach-mvebu: remove redundant DT parsing and validation
ARM: msm: Only compile io.c on platforms that use it
iommu/msm: Move mach includes to iommu directory
ARM: msm: Remove devices-iommu.c
ARM: msm: Move mach/board.h contents to common.h
ARM: msm: Migrate msm_timer to CLOCKSOURCE_OF_DECLARE
ARM: msm: Remove TMR and TMR0 static mappings
...
Linus Torvalds [Fri, 6 Sep 2013 20:17:02 +0000 (13:17 -0700)]
Merge tag 'fixes-nc-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC low-priority fixes from Olof Johansson:
"This branch contains a handful of fixes for various platforms that
weren't serious enough to be included in late 3.11-rc releases. Most
of them are for minor cleanups and cosmetic fixes.
There's also a bit of code removal here, one board file removal for
clps711x, and removal of some legacy device creation on OMAP2+"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
ARM: OMAP2: use 'int' instead of 'unsigned' for variable 'gpmc_irq_start'
ARM: OMAP2: remove useless variable 'ret'
ARM: OMAP: dma: fix error return code in omap_system_dma_probe()
ARM: OMAP2+: fix wrong address when loading PRM_FRAC_INCREMENTOR_DENUMERATOR_RELOAD
ARM: OMAP2+: am33xx-restart: trigger warm reset on omap2+ boards
ARM: OMAP2: Use a consistent AM33XX SoC option description
ARM: OMAP2+: Remove legacy device creation for McPDM and DMIC
ARM: clps711x:
edb7211: Remove extra iotable_init() call
ARM: clps711x: autcpu12: Remove incorrect config checking
ARM: clps711x: Drop fortunet board support
ARM: clps711x: Remove the special name for the syscon driver
ARM: dts: Fix memory node in skeleton64.dtsi
ARM: Keystone: Convert device tree file to use IRQ defines
ARM: keystone: use #include to include skeleton.dtsi
ARM: keystone: Drop the un-necessary dsb from keystone_cpu_smc()
ARM: Keystone: No need to preserve r12 across smc call
ARM: keystone: remove redundant smp_init_cpus definition
ARM: keystone: drop useless HAVE_SCHED_CLOCK
ARM: dove: fix missing __init section of dove_mpp_gpio_mode
ARM: shmobile: armadillo800eva-reference: fix compiler warning
...
Linus Torvalds [Fri, 6 Sep 2013 20:16:01 +0000 (13:16 -0700)]
Merge tag 'please-pull-misc-3.12' of git://git./linux/kernel/git/aegl/linux
Pull ia64 fixes from Tony Luck:
"Couple of small cleanups for ia64"
* tag 'please-pull-misc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] Use asm-generic/bitops/builtin-ffs.h
[IA64] dmi.h: Make dmi_alloc use kzalloc
Yan, Zheng [Mon, 2 Sep 2013 07:19:54 +0000 (15:19 +0800)]
ceph: use d_invalidate() to invalidate aliases
d_invalidate() is the standard VFS method to invalidate dentry.
compare to d_delete(), it also try shrinking children dentries.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Yan, Zheng [Mon, 2 Sep 2013 07:19:53 +0000 (15:19 +0800)]
ceph: remove ceph_lookup_inode()
commit
6f60f889 (ceph: fix freeing inode vs removing session caps race)
introduced ceph_lookup_inode(). But there is already a ceph_find_inode()
which provides similar function. So remove ceph_lookup_inode(), use
ceph_find_inode() instead.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Reviewed-by: Alex Elder <alex.elder@linary.org>
Reviewed-by: Sage Weil <sage@inktank.com>
Andy Adamson [Fri, 6 Sep 2013 18:14:00 +0000 (14:14 -0400)]
NFSv4.1 Use MDS auth flavor for data server connection
Commit
4edaa308 "NFS: Use "krb5i" to establish NFSv4 state whenever possible"
uses the nfs_client cl_rpcclient for all state management operations, and
will use krb5i or auth_sys with no regard to the mount command authflavor
choice.
The MDS, as any NFSv4.1 mount point, uses the nfs_server rpc client for all
non-state management operations with a different nfs_server for each fsid
encountered traversing the mount point, each with a potentially different
auth flavor.
pNFS data servers are not mounted in the normal sense as there is no associated
nfs_server structure. Data servers can also export multiple fsids, each with
a potentially different auth flavor.
Data servers need to use the same authflavor as the MDS server rpc client for
non-state management operations. Populate a list of rpc clients with the MDS
server rpc client auth flavor for the DS to use.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Eric Dumazet [Fri, 6 Sep 2013 17:35:58 +0000 (10:35 -0700)]
tcp: properly increase rcv_ssthresh for ofo packets
TCP receive window handling is multi staged.
A socket has a memory budget, static or dynamic, in sk_rcvbuf.
Because we do not really know how this memory budget translates to
a TCP window (payload), TCP announces a small initial window
(about 20 MSS).
When a packet is received, we increase TCP rcv_win depending
on the payload/truesize ratio of this packet. Good citizen
packets give a hint that it's reasonable to have rcv_win = sk_rcvbuf/2
This heuristic takes place in tcp_grow_window()
Problem is : We currently call tcp_grow_window() only for in-order
packets.
This means that reorders or packet losses stop proper grow of
rcv_win, and senders are unable to benefit from fast recovery,
or proper reordering level detection.
Really, a packet being stored in OFO queue is not a bad citizen.
It should be part of the game as in-order packets.
In our traces, we very often see sender is limited by linux small
receive windows, even if linux hosts use autotuning (DRS) and should
allow rcv_win to grow to ~3MB.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 6 Sep 2013 15:58:00 +0000 (16:58 +0100)]
net: add documentation for BQL helpers
Provide a kernel-doc comment documentation for the BQL helpers:
- netdev_sent_queue
- netdev_completed_queue
- netdev_reset_queue
Similarly to how it is done for the other functions, the documentation
only covers the function operating on struct net_device and not struct
netdev_queue.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Opdenacker [Fri, 6 Sep 2013 11:49:22 +0000 (13:49 +0200)]
mlx5: remove unused MLX5_DEBUG param in Kconfig
This patch proposes to remove the MLX5_DEBUG kernel configuration
parameter defined in drivers/net/ethernet/mellanox/mlx5/core/Kconfig,
but used nowhere in the makefiles and source code.
This could also be fixed by using this parameter,
but this may be a leftover from driver development...
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Fri, 6 Sep 2013 09:55:02 +0000 (12:55 +0300)]
bnx2x: Restore a call to config_init
Commit
c0a77ec74f295013d7ba3204dd3ed25fccf83cb4 'bnx2x: Add missing braces in
bnx2x:bnx2x_link_initialize' identified indentation problem, but resolved it
by adding braces instead of fixing the indentation. The braces now prevents a
config_init call in some cases, though it should be called regardless of that
condition. This patch removes the braces and fix the confusing indentation
that caused this mess.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
CC: Dave Jones <davej@redhat.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Fri, 6 Sep 2013 07:35:28 +0000 (10:35 +0300)]
bnx2x: fix broken compilation with CONFIG_BNX2X_SRIOV is not set
Since commit
60cad4e67bd6ff400e7ea61fe762b3042b12ae9d
"bnx2x: VF RSS support - VF side" fails to compile w/o
CONFIG_BNX2X_SRIOV option.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Thu, 5 Sep 2013 22:36:09 +0000 (15:36 -0700)]
tcp: fix no cwnd growth after timeout
In commit
0f7cc9a3 "tcp: increase throughput when reordering is high",
it only allows cwnd to increase in Open state. This mistakenly disables
slow start after timeout (CA_Loss). Moreover cwnd won't grow if the
state moves from Disorder to Open later in tcp_fastretrans_alert().
Therefore the correct logic should be to allow cwnd to grow as long
as the data is received in order in Open, Loss, or even Disorder state.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 5 Sep 2013 15:48:47 +0000 (17:48 +0200)]
net: netlink: filter particular protocols from analyzers
Fix finer-grained control and let only a whitelist of allowed netlink
protocols pass, in our case related to networking. If later on, other
subsystems decide they want to add their protocol as well to the list
of allowed protocols they shall simply add it. While at it, we also
need to tell what protocol is in use otherwise BPF_S_ANC_PROTOCOL can
not pick it up (as it's not filled out).
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 6 Sep 2013 18:14:33 +0000 (11:14 -0700)]
Merge git://git./linux/kernel/git/cmetcalf/linux-tile
Pull Tile arch updates from Chris Metcalf:
"These changes bring in a bunch of new functionality that has been
maintained internally at Tilera over the last year, plus other stray
bits of work that I've taken into the tile tree from other folks.
The changes include some PCI root complex work, interrupt-driven
console support, support for performing fast-path unaligned data
fixups by kernel-based JIT code generation, CONFIG_PREEMPT support,
vDSO support for gettimeofday(), a serial driver for the tilegx
on-chip UART, KGDB support, more optimized string routines, support
for ftrace and kprobes, improved ASLR, and many bug fixes.
We also remove support for the old TILE64 chip, which is no longer
buildable"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (85 commits)
tile: refresh tile defconfig files
tile: rework <asm/cmpxchg.h>
tile PCI RC: make default consistent DMA mask 32-bit
tile: add null check for kzalloc in tile/kernel/setup.c
tile: make __write_once a synonym for __read_mostly
tile: remove support for TILE64
tile: use asm-generic/bitops/builtin-*.h
tile: eliminate no-op "noatomichash" boot argument
tile: use standard tile_bundle_bits type in traps.c
tile: simplify code referencing hypervisor API addresses
tile: change <asm/system.h> to <asm/switch_to.h> in comments
tile: mark pcibios_init() as __init
tile: check for correct compiler earlier in asm-offsets.c
tile: use standard 'generic-y' model for <asm/hw_irq.h>
tile: use asm-generic version of <asm/local64.h>
tile PCI RC: add comment about "PCI hole" problem
tile: remove DEBUG_EXTRA_FLAGS kernel config option
tile: add virt_to_kpte() API and clean up and document behavior
tile: support FRAME_POINTER
tile: support reporting Tilera hypervisor statistics
...
Linus Torvalds [Fri, 6 Sep 2013 18:09:44 +0000 (11:09 -0700)]
Merge tag 'arm64-for-linus' of git://git./linux/kernel/git/cmarinas/linux-aarch64
Pull ARM64 update from Catalin Marinas:
- User tagged pointers support (top 8-bit of user pointers
automatically ignored by the CPU).
- Kernel mode NEON (no users for arm64 yet but work in progress).
- arm64 kernel Image header extended to accommodate future EFI stub.
- Remove BogoMIPS reporting (not relevant, it's just the timer
frequency).
- Clean-up (EM_AARCH64/EM_ARM to elf-em.h, ELF notes in read-only
segment, unused variable).
- Bug-fixes (RAM boundaries not 2MB aligned, perf, includes).
* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
Documentation/arm64: clarify requirements for DTB placement
arm64: mm: permit use of tagged pointers at EL0
Move the EM_ARM and EM_AARCH64 definitions to uapi/linux/elf-em.h
arm64: Remove unused cpu_name ascii in arch/arm64/mm/proc.S
arm64: delay: don't bother reporting bogomips in /proc/cpuinfo
arm64: Fix mapping of memory banks not ending on a PMD_SIZE boundary
arm64: move elf notes into readonly segment
arm64: Enable interrupts in the EL0 undef handler
arm64: Expand arm64 image header
ARM64: include: asm: include "asm/types.h" in "pgtable-2level-types.h" and "pgtable-3level-types.h"
arm64: add support for kernel mode NEON
arm64: perf: fix ARMv8 EVTYPE_MASK to include NSH bit
arm64: perf: fix group validation when using enable_on_exec
Linus Torvalds [Fri, 6 Sep 2013 17:58:34 +0000 (10:58 -0700)]
Merge tag 'microblaze-3.12-rc1' of git://git.monstr.eu/linux-2.6-microblaze
Pull Microblaze patches from Michal Simek:
- PCI fixes
- Selfmod code removing
- Intc and timer fixes
- Adding new MB versions
- Minor fixes
* tag 'microblaze-3.12-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Show message when reset gpio is not present
microblaze: Add linux.bin.ub target
microblaze: Add PVR version string for MB v9.0 and v9.1
microblaze: timer: Replace microblaze_ prefix by xilinx_
microblaze: timer: Update header
microblaze: timer: Remove unused header
microblaze: timer: Clear driver init function
microblaze: timer: Use CLKSRC_OF initialization
microblaze: intc: Remove unused header
microblaze: intc: Clean driver init function
microblaze: intc: Using irqchip
microblaze: intc: Update header
microblaze: intc: Remove unused headers
microblaze: Remove selfmodified feature
of/pci: Use of_pci_range_parser
Linus Torvalds [Fri, 6 Sep 2013 17:49:42 +0000 (10:49 -0700)]
Merge branch 'next' of git://git./linux/kernel/git/benh/powerpc
Pull powerpc updates from Ben Herrenschmidt:
"Here's the powerpc batch for this merge window. Some of the
highlights are:
- A bunch of endian fixes ! We don't have full LE support yet in that
release but this contains a lot of fixes all over arch/powerpc to
use the proper accessors, call the firmware with the right endian
mode, etc...
- A few updates to our "powernv" platform (non-virtualized, the one
to run KVM on), among other, support for bridging the P8 LPC bus
for UARTs, support and some EEH fixes.
- Some mpc51xx clock API cleanups in preparation for a clock API
overhaul
- A pile of cleanups of our old math emulation code, including better
support for using it to emulate optional FP instructions on
embedded chips that otherwise have a HW FPU.
- Some infrastructure in selftest, for powerpc now, but could be
generalized, initially used by some tests for our perf instruction
counting code.
- A pile of fixes for hotplug on pseries (that was seriously
bitrotting)
- The usual slew of freescale embedded updates, new boards, 64-bit
hiberation support, e6500 core PMU support, etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc: Correct FSCR bit definitions
powerpc/xmon: Fix printing of set of CPUs in xmon
powerpc/pseries: Move lparcfg.c to platforms/pseries
powerpc/powernv: Return secondary CPUs to firmware on kexec
powerpc/btext: Fix CONFIG_PPC_EARLY_DEBUG_BOOTX on ppc32
powerpc: Cleanup handling of the DSCR bit in the FSCR register
powerpc/pseries: Child nodes are not detached by dlpar_detach_node
powerpc/pseries: Add mising of_node_put in delete_dt_node
powerpc/pseries: Make dlpar_configure_connector parent node aware
powerpc/pseries: Do all node initialization in dlpar_parse_cc_node
powerpc/pseries: Fix parsing of initial node path in update_dt_node
powerpc/pseries: Pack update_props_workarea to map correctly to rtas buffer header
powerpc/pseries: Fix over writing of rtas return code in update_dt_node
powerpc/pseries: Fix creation of loop in device node property list
powerpc: Skip emulating & leave interrupts off for kernel program checks
powerpc: Add more exception trampolines for hypervisor exceptions
powerpc: Fix location and rename exception trampolines
powerpc: Add more trap names to xmon
powerpc/pseries: Add a warning in the case of cross-cpu VPA registration
powerpc: Update the 00-Index in Documentation/powerpc
...
Chris Metcalf [Fri, 6 Sep 2013 12:58:35 +0000 (08:58 -0400)]
tile: refresh tile defconfig files
These are based on the current shipping versions of the config files
from Tilera, as synced up to the tip, so are a better starting point
for folks who want a default configuration.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Fri, 6 Sep 2013 12:56:45 +0000 (08:56 -0400)]
tile: rework <asm/cmpxchg.h>
The macrology in cmpxchg.h was designed to allow arbitrary pointer
and integer values to be passed through the routines. To support
cmpxchg() on 64-bit values on the 32-bit tilepro architecture, we
used the idiom "(typeof(val))(typeof(val-val))". This way, in the
"size 8" branch of the switch, when the underlying cmpxchg routine
returns a 64-bit quantity, we cast it first to a typeof(val-val)
quantity (i.e. size_t if "val" is a pointer) with no warnings about
casting between pointers and integers of different sizes, then cast
onwards to typeof(val), again with no warnings. If val is not a
pointer type, the additional cast is a no-op. We can't replace the
typeof(val-val) cast with (for example) unsigned long, since then if
"val" is really a 64-bit type, we cast away the high bits.
HOWEVER, this fails with current gcc (through 4.7 at least) if "val"
is a pointer to an incomplete type. Unfortunately gcc isn't smart
enough to realize that "val - val" will always be a size_t type
even if it's an incomplete type pointer.
Accordingly, I've reworked the way we handle the casting. We have
given up the ability to use cmpxchg() on 64-bit values on tilepro,
which is OK in the kernel since we should use cmpxchg64() explicitly
on such values anyway. As a result, I can just use simple "unsigned
long" casts internally.
As I reworked it, I realized it would be cleaner to move the
architecture-specific conditionals for cmpxchg and xchg out of the
atomic.h headers and into cmpxchg, and then use the cmpxchg() and
xchg() primitives directly in atomic.h and elsewhere. This allowed
the cmpxchg.h header to stand on its own without relying on the
implicit include of it that is performed by <asm/atomic.h>.
It also allowed collapsing the atomic_xchg/atomic_cmpxchg routines
from atomic_{32,64}.h into atomic.h.
I improved the tests that guard the allowed size of the arguments
to the routines to use a __compiletime_error() test. (By avoiding
the use of BUILD_BUG, I could include cmpxchg.h into bitops.h as
well and use the macros there, which is otherwise impossible due
to include order dependency issues.)
The tilepro _atomic_xxx internal methods were previously set up to
take atomic_t and atomic64_t arguments, which isn't as convenient
with the new model, so I modified them to take int or u64 arguments,
which is consistent with how they used the arguments internally
anyway, so provided some nice simplification there too.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Milosz Tanski [Fri, 6 Sep 2013 15:13:18 +0000 (15:13 +0000)]
ceph: trivial buildbot warnings fix
The linux-next build bot found a three of warnings, this addresses all of them.
* non-ANSI function declaration of function 'ceph_fscache_register' and
'ceph_fscache_unregister'
* symbol 'ceph_cache_netfs' was not declared, now it's extern in the header.
* warning: "pr_fmt" redefined
Signed-off-by: Milosz Tanski <milosz@adfin.com>
Milosz Tanski [Thu, 5 Sep 2013 18:29:03 +0000 (18:29 +0000)]
ceph: Do not do invalidate if the filesystem is mounted nofsc
Previously we would always try to enqueue work even if the filesystem is not
mounted with fscache enabled (or the file has no cookie). In the case of the
filesystem mouned nofsc (but with fscache compiled in) this would lead to a
crash.
Signed-off-by: Milosz Tanski <milosz@adfin.com>
Milosz Tanski [Tue, 3 Sep 2013 23:11:17 +0000 (19:11 -0400)]
ceph: page still marked private_2
Previous patch that allowed us to cleanup most of the issues with pages marked
as private_2 when calling ceph_readpages. However, there seams to be a case in
the error case clean up in start read that still trigers this from time to
time. I've only seen this one a couple times.
BUG: Bad page state in process petabucket pfn:335b82
page:
ffffea000cd6e080 count:0 mapcount:0 mapping: (null) index:0x0
page flags: 0x200000000001000(private_2)
Call Trace:
[<
ffffffff81563442>] dump_stack+0x46/0x58
[<
ffffffff8112c7f7>] bad_page+0xc7/0x120
[<
ffffffff8112cd9e>] free_pages_prepare+0x10e/0x120
[<
ffffffff8112e580>] free_hot_cold_page+0x40/0x160
[<
ffffffff81132427>] __put_single_page+0x27/0x30
[<
ffffffff81132d95>] put_page+0x25/0x40
[<
ffffffffa02cb409>] ceph_readpages+0x2e9/0x6f0 [ceph]
[<
ffffffff811313cf>] __do_page_cache_readahead+0x1af/0x260
Signed-off-by: Milosz Tanski <milosz@adfin.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Milosz Tanski [Tue, 3 Sep 2013 23:11:01 +0000 (19:11 -0400)]
ceph: ceph_readpage_to_fscache didn't check if marked
Previously ceph_readpage_to_fscache did not call if page was marked as cached
before calling fscache_write_page resulting in a BUG inside of fscache.
FS-Cache: Assertion failed
------------[ cut here ]------------
kernel BUG at fs/fscache/page.c:874!
invalid opcode: 0000 [#1] SMP
Call Trace:
[<
ffffffffa02e6566>] __ceph_readpage_to_fscache+0x66/0x80 [ceph]
[<
ffffffffa02caf84>] readpage_nounlock+0x124/0x210 [ceph]
[<
ffffffffa02cb08d>] ceph_readpage+0x1d/0x40 [ceph]
[<
ffffffff81126db6>] generic_file_aio_read+0x1f6/0x700
[<
ffffffffa02c6fcc>] ceph_aio_read+0x5fc/0xab0 [ceph]
Signed-off-by: Milosz Tanski <milosz@adfin.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Milosz Tanski [Wed, 21 Aug 2013 21:30:27 +0000 (17:30 -0400)]
ceph: clean PgPrivate2 on returning from readpages
In some cases the ceph readapages code code bails without filling all the pages
already marked by fscache. When we return back to readahead code this causes
a BUG.
Signed-off-by: Milosz Tanski <milosz@adfin.com>
Milosz Tanski [Wed, 21 Aug 2013 21:29:54 +0000 (17:29 -0400)]
ceph: use fscache as a local presisent cache
Adding support for fscache to the Ceph filesystem. This would bring it to on
par with some of the other network filesystems in Linux (like NFS, AFS, etc...)
In order to mount the filesystem with fscache the 'fsc' mount option must be
passed.
Signed-off-by: Milosz Tanski <milosz@adfin.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Milosz Tanski [Fri, 6 Sep 2013 16:41:20 +0000 (16:41 +0000)]
Merge tag 'fscache-fixes-for-ceph' into wip-fscache
Patches for Ceph FS-Cache support
Linus Torvalds [Fri, 6 Sep 2013 16:36:28 +0000 (09:36 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
Linus Torvalds [Fri, 6 Sep 2013 16:30:36 +0000 (09:30 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
"Highlights:
- conversion of HID subsystem to use devm-based resource management,
from Benjamin Tissoires
- i2c-hid support for DT bindings, from Benjamin Tissoires
- much improved support for Win8-multitouch devices, from Benjamin
Tissoires
- cleanup of core code using common hidinput_input_event(), from
David Herrmann
- fix for bug in implement() access to the bit stream (causing oops)
that has been present in the code for ages, but devices that are
able to trigger it have started to appear only now, from Jiri
Kosina
- fixes for CVE-2013-2899, CVE-2013-2898, CVE-2013-2896,
CVE-2013-2892, CVE-2013-2888 (all triggerable only by specially
crafted malicious HW devices plugged into the system), from Kees
Cook
- hidraw oops fix, from Manoj Chourasia
- various smaller fixes here and there, support for a bunch of new
devices by various contributors"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (53 commits)
HID: MAINTAINERS: add roccat drivers
HID: hid-sensor-hub: change kmalloc + memcpy by kmemdup
HID: hid-sensor-hub: move to devm_kzalloc
HID: hid-sensor-hub: fix indentation accross the code
HID: move HID_REPORT_TYPES closer to the report-definitions
HID: check for NULL field when setting values
HID: picolcd_core: validate output report details
HID: sensor-hub: validate feature report details
HID: ntrig: validate feature report details
HID: pantherlord: validate output report details
HID: hid-wiimote: print small buffers via %*phC
HID: uhid: improve uhid example client
HID: Correct the USB IDs for the new Macbook Air 6
HID: wiimote: add support for Guitar-Hero guitars
HID: wiimote: add support for Guitar-Hero drums
Input: introduce BTN/ABS bits for drums and guitars
HID: battery: don't do DMA from stack
HID: roccat: add support for KonePureOptical v2
HID: picolcd: Prevent NULL pointer dereference on _remove()
HID: usbhid: quirk for N-Trig DuoSense Touch Screen
...
Linus Torvalds [Fri, 6 Sep 2013 16:06:02 +0000 (09:06 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-fs
Pull ext3, reiserfs, udf & isofs fixes from Jan Kara:
"The contains a bunch of ext3 cleanups and minor improvements, major
reiserfs locking changes which should hopefully fix deadlocks
introduced by BKL removal, and udf/isofs changes to refuse mounting fs
rw instead of mounting it ro automatically which makes eject button
work as expected for all media (see the changelog for why userspace
should be ok with this change)"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
jbd: use a single printk for jbd_debug()
reiserfs: locking, release lock around quota operations
reiserfs: locking, handle nested locks properly
reiserfs: locking, push write lock out of xattr code
jbd: relocate assert after state lock in journal_commit_transaction()
udf: Refuse RW mount of the filesystem instead of making it RO
udf: Standardize return values in mount sequence
isofs: Refuse RW mount of the filesystem instead of making it RO
ext3: allow specifying external journal by pathname mount option
jbd: remove unneeded semicolon
Linus Torvalds [Fri, 6 Sep 2013 16:04:34 +0000 (09:04 -0700)]
Merge tag 'for-f2fs-3.12' of git://git./linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"This patch-set includes the following major enhancement patches:
- support inline xattrs
- add sysfs support to control GCs explicitly
- add proc entry to show the current segment usage information
- improve the GC/SSR performance
The other bug fixes are as follows:
- avoid the overflow on status calculation
- fix some error handling routines
- fix inconsistent xattr states after power-off-recovery
- fix incorrect xattr node offset definition
- fix deadlock condition in fsync
- fix the fdatasync routine for power-off-recovery"
* tag 'for-f2fs-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (40 commits)
f2fs: optimize gc for better performance
f2fs: merge more bios of node block writes
f2fs: avoid an overflow during utilization calculation
f2fs: trigger GC when there are prefree segments
f2fs: use strncasecmp() simplify the string comparison
f2fs: fix omitting to update inode page
f2fs: support the inline xattrs
f2fs: add the truncate_xattr_node function
f2fs: introduce __find_xattr for readability
f2fs: reserve the xattr space dynamically
f2fs: add flags for inline xattrs
f2fs: fix error return code in init_f2fs_fs()
f2fs: fix wrong BUG_ON condition
f2fs: fix memory leak when init f2fs filesystem fail
f2fs: fix a compound statement label error
f2fs: avoid writing inode redundantly when creating a file
f2fs: alloc_page() doesn't return an ERR_PTR
f2fs: should cover i_xattr_nid with its xattr node page lock
f2fs: check the free space first in new_node_page
f2fs: clean up the needless end 'return' of void function
...
Trond Myklebust [Fri, 6 Sep 2013 15:09:38 +0000 (11:09 -0400)]
NFS: Don't check lock owner compatability unless file is locked (part 2)
When coalescing requests into a single READ or WRITE RPC call, and there
is no file locking involved, we don't have to refuse coalescing for
requests where the lock owner information doesn't match.
Reported-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Guenter Roeck [Fri, 6 Sep 2013 12:05:43 +0000 (14:05 +0200)]
hwmon: (emc6w201) Do not declare enum variable
Fix the following smatch warning:
emc6w201.c:52:26: warning: symbol 'subfeature' was not declared.
Should it be static?
'enum { } subtype' declares an enum as (global) variable which we don't want.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Shane Huang [Fri, 6 Sep 2013 12:05:42 +0000 (14:05 +0200)]
hwmon: (w83792d) Update module author
w83792d was written by me in 2004, I'd like to update my first name
into my current one to keep consistent, and delete invalid address.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jiri Kosina [Fri, 6 Sep 2013 09:59:53 +0000 (11:59 +0200)]
Merge branch 'for-3.12/sensor-hub' into for-linus
Conflicts:
drivers/hid/hid-sensor-hub.c
Jiri Kosina [Fri, 6 Sep 2013 09:58:37 +0000 (11:58 +0200)]
Merge branches 'for-3.12/devm', 'for-3.12/i2c-hid', 'for-3.12/i2c-hid-dt', 'for-3.12/logitech', 'for-3.12/multitouch-win8', 'for-3.12/trasnport-driver-cleanup', 'for-3.12/uhid', 'for-3.12/upstream' and 'for-3.12/wiimote' into for-linus
Milosz Tanski [Wed, 21 Aug 2013 21:30:11 +0000 (17:30 -0400)]
fscache: Netfs function for cleanup post readpages
Currently the fscache code expect the netfs to call fscache_readpages_or_alloc
inside the aops readpages callback. It marks all the pages in the list
provided by readahead with PG_private_2. In the cases that the netfs fails to
read all the pages (which is legal) it ends up returning to the readahead and
triggering a BUG. This happens because the page list still contains marked
pages.
This patch implements a simple fscache_readpages_cancel function that the netfs
should call before returning from readpages. It will revoke the pages from the
underlying cache backend and unmark them.
The problem was originally worked out in the Ceph devel tree, but it also
occurs in CIFS. It appears that NFS, AFS and 9P are okay as read_cache_pages()
will clean up the unprocessed pages in the case of an error.
This can be used to address the following oops:
[
12410647.597278] BUG: Bad page state in process petabucket pfn:3d504e
[
12410647.597292] page:
ffffea000f541380 count:0 mapcount:0 mapping:
(null) index:0x0
[
12410647.597298] page flags: 0x200000000001000(private_2)
...
[
12410647.597334] Call Trace:
[
12410647.597345] [<
ffffffff815523f2>] dump_stack+0x19/0x1b
[
12410647.597356] [<
ffffffff8111def7>] bad_page+0xc7/0x120
[
12410647.597359] [<
ffffffff8111e49e>] free_pages_prepare+0x10e/0x120
[
12410647.597361] [<
ffffffff8111fc80>] free_hot_cold_page+0x40/0x170
[
12410647.597363] [<
ffffffff81123507>] __put_single_page+0x27/0x30
[
12410647.597365] [<
ffffffff81123df5>] put_page+0x25/0x40
[
12410647.597376] [<
ffffffffa02bdcf9>] ceph_readpages+0x2e9/0x6e0 [ceph]
[
12410647.597379] [<
ffffffff81122a8f>] __do_page_cache_readahead+0x1af/0x260
[
12410647.597382] [<
ffffffff81122ea1>] ra_submit+0x21/0x30
[
12410647.597384] [<
ffffffff81118f64>] filemap_fault+0x254/0x490
[
12410647.597387] [<
ffffffff8113a74f>] __do_fault+0x6f/0x4e0
[
12410647.597391] [<
ffffffff810125bd>] ? __switch_to+0x16d/0x4a0
[
12410647.597395] [<
ffffffff810865ba>] ? finish_task_switch+0x5a/0xc0
[
12410647.597398] [<
ffffffff8113d856>] handle_pte_fault+0xf6/0x930
[
12410647.597401] [<
ffffffff81008c33>] ? pte_mfn_to_pfn+0x93/0x110
[
12410647.597403] [<
ffffffff81008cce>] ? xen_pmd_val+0xe/0x10
[
12410647.597405] [<
ffffffff81005469>] ? __raw_callee_save_xen_pmd_val+0x11/0x1e
[
12410647.597407] [<
ffffffff8113f361>] handle_mm_fault+0x251/0x370
[
12410647.597411] [<
ffffffff812b0ac4>] ? call_rwsem_down_read_failed+0x14/0x30
[
12410647.597414] [<
ffffffff8155bffa>] __do_page_fault+0x1aa/0x550
[
12410647.597418] [<
ffffffff8108011d>] ? up_write+0x1d/0x20
[
12410647.597422] [<
ffffffff8113141c>] ? vm_mmap_pgoff+0xbc/0xe0
[
12410647.597425] [<
ffffffff81143bb8>] ? SyS_mmap_pgoff+0xd8/0x240
[
12410647.597427] [<
ffffffff8155c3ae>] do_page_fault+0xe/0x10
[
12410647.597431] [<
ffffffff81558818>] page_fault+0x28/0x30
Signed-off-by: Milosz Tanski <milosz@adfin.com>
Signed-off-by: David Howells <dhowells@redhat.com>