OSDN Git Service
Rob Herring [Sun, 24 Oct 2021 23:22:39 +0000 (01:22 +0200)]
ARM: dts: arm: Update ICST clock nodes 'reg' and node names
Add a 'reg' entry for ICST clock nodes on the Arm Ltd platforms. The 'reg'
entry is the VCO register address. With this, the node name can be updated
to use a generic node name, 'clock-controller', and a unit-address.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20211024232239.211822-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rob Herring [Sun, 24 Oct 2021 23:20:03 +0000 (01:20 +0200)]
ARM: dts: arm: Update register-bit-led nodes 'reg' and node names
Add a 'reg' entry for register-bit-led nodes on the Arm Ltd platforms.
The 'reg' entry is the LED control register address. With this, the node
name can be updated to use a generic node name, 'led', and a
unit-address.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20211024232003.211484-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 22 Oct 2021 20:02:01 +0000 (22:02 +0200)]
Merge tag 'aspeed-5.16-devicetree-2' of git://git./linux/kernel/git/joel/bmc into arm/dt
ASPEED device tree updates for 5.16, round 2
- New machines:
* Inventec Transformers, an x86 family server with an AST2600 BMC
- Updates to the Everest and Rainier sensors, gpios and KCS devices
- New UART routing device tree description
* tag 'aspeed-5.16-devicetree-2' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc:
ARM: dts: aspeed: Add uart routing to device tree
ARM: dts: aspeed: rainier: Enable earlycon
ARM: dts: aspeed: rainier: Add front panel LEDs
ARM: dts: aspeed: rainier: Add 'factory-reset-toggle' as GPIOF6
ARM: dts: aspeed: rainier: Remove PSU gpio-keys
ARM: dts: aspeed: rainier: Remove gpio hog for GPIOP7
ARM: dts: aspeed: rainier: Add eeprom on bus 12
ARM: dts: aspeed: p10bmc: Enable KCS channel 2
ARM: dts: aspeed: p10bmc: Use KCS 3 for MCTP binding
ARM: dts: aspeed: Adding Inventec Transformers BMC
ARM: dts: aspeed: everest: Fix bus 15 muxed eeproms
ARM: dts: aspeed: everest: Add IBM Operation Panel I2C device
ARM: dts: aspeed: everest: Add I2C switch on bus 8
ARM: dts: aspeed: rainier and everest: Remove PCA gpio specification
ARM: dts: aspeed: p10bmc: Fix ADC iio-hwmon battery node name
Link: https://lore.kernel.org/r/CACPK8Xd=eAMk-S3akhGgL4i_K190Nz9t=_CrdHQMJ+nbW172mg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Paweł Anikiel [Thu, 21 Oct 2021 15:17:36 +0000 (17:17 +0200)]
dts: socfpga: Add Mercury+ AA1 devicetree
Add support for the Mercury+ AA1 module for Arria 10 SoC FPGA.
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Signed-off-by: Joanna Brozek <jbrozek@antmicro.com>
Signed-off-by: Mariusz Glebocki <mglebocki@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Maciej Mikunda <mmikunda@antmicro.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211021151736.2096926-2-pan@semihalf.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rob Herring [Fri, 22 Oct 2021 14:11:56 +0000 (09:11 -0500)]
ARM: dts: spear13xx: Drop malformed 'interrupt-map' on PCI nodes
The spear13xx PCI 'interrupt-map' property is not parse-able.
'#interrupt-cells' is missing and there are 3 #address-cells. Based on the
driver, the only supported interrupt is for MSI. Therefore, 'interrupt-map'
is not needed.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20211022141156.2592221-1-robh@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Chia-Wei Wang [Mon, 27 Sep 2021 02:30:53 +0000 (10:30 +0800)]
ARM: dts: aspeed: Add uart routing to device tree
Add LPC uart routing to the device tree for Aspeed SoCs.
Signed-off-by: Oskar Senft <osk@google.com>
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Tested-by: Lei YU <yulei.sh@bytedance.com>
Link: https://lore.kernel.org/r/20210927023053.6728-6-chiawei_wang@aspeedtech.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Joel Stanley [Tue, 29 Jun 2021 07:23:08 +0000 (16:53 +0930)]
ARM: dts: aspeed: rainier: Enable earlycon
Rainier was missed when enabling all of the other machines in
commit
239566b032f3 ("ARM: dts: aspeed: Set earlycon boot argument").
Signed-off-by: Joel Stanley <joel@jms.id.au>
Joel Stanley [Thu, 21 Oct 2021 06:18:34 +0000 (16:48 +1030)]
ARM: dts: aspeed: rainier: Add front panel LEDs
These were meant to be part of commit
4fb27b3f9176 ("ARM: dts: aspeed:
rainier: Add system LEDs") but went missing.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Isaac Kurth [Wed, 14 Jul 2021 21:47:41 +0000 (16:47 -0500)]
ARM: dts: aspeed: rainier: Add 'factory-reset-toggle' as GPIOF6
The state of this GPIO determines whether a factory reset has been
requested. If a physical switch is used, it can be high or low. During boot,
the software checks and records the state of this switch. If it is different
than the previous recorded state, then the read-write portions of memory are
reformatted.
Signed-off-by: Isaac Kurth <isaac.kurth@ibm.com>
Reviewed-by: Adriana Kobylak <anoo@us.ibm.com>
Link: https://lore.kernel.org/r/20210714214741.1547052-1-blisaac91@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
B. J. Wyman [Wed, 23 Jun 2021 23:04:01 +0000 (23:04 +0000)]
ARM: dts: aspeed: rainier: Remove PSU gpio-keys
Remove the gpio-keys entries for the power supply presence lines from
the Rainier device tree. The user space applications are going to change
from using libevdev to libgpiod.
Signed-off-by: B. J. Wyman <bjwyman@gmail.com>
Link: https://lore.kernel.org/r/20210623230401.3050076-1-bjwyman@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Eddie James [Wed, 15 Sep 2021 21:47:38 +0000 (16:47 -0500)]
ARM: dts: aspeed: rainier: Remove gpio hog for GPIOP7
Only the pass 1 Ingraham board (Rainier system) had a micro-controller
wired to GPIOP7 on ball Y23. Pass 2 boards have this ball wired to the
heartbeat LED, so remove the hog as this device tree supports pass 2.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210915214738.34382-5-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Eddie James [Wed, 15 Sep 2021 21:47:37 +0000 (16:47 -0500)]
ARM: dts: aspeed: rainier: Add eeprom on bus 12
The devicetree was missing an eeprom.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210915214738.34382-4-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Andrew Jeffery [Wed, 23 Jun 2021 03:38:54 +0000 (13:08 +0930)]
ARM: dts: aspeed: p10bmc: Enable KCS channel 2
Rainier uses KCS channel 2 as the source for the debug-trigger
application outlined at [1] and implemented at [2].
[1] https://github.com/openbmc/docs/blob/master/designs/bmc-service-failure-debug-and-recovery.md
[2] https://github.com/openbmc/debug-trigger
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210623033854.587464-8-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Andrew Jeffery [Wed, 23 Jun 2021 03:38:51 +0000 (13:08 +0930)]
ARM: dts: aspeed: p10bmc: Use KCS 3 for MCTP binding
The MCTP LPC driver was loaded by hacking up the compatible in the
devicetree node for KCS 4. With the introduction of the raw KCS driver
this hack is no-longer required. Use the regular compatible string for
KCS 4 and configure the appropriate SerIRQ.
The reset state of the status bits on KCS 4 is inappropriate for the
MCTP LPC binding. Switch to KCS 3 which has a different reset behaviour.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Lin.TommySC 林世欽 TAO [Tue, 19 Oct 2021 08:42:14 +0000 (08:42 +0000)]
ARM: dts: aspeed: Adding Inventec Transformers BMC
Initial introduction of Inventec Transformers x86 family equipped with
AST2600 BMC SoC.
Signed-off-by: Tommy Lin <Lin.TommySC@inventec.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/7d7b20575f994a3c9018223a3c5f198d@inventec.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Eddie James [Wed, 20 Oct 2021 21:53:21 +0000 (16:53 -0500)]
ARM: dts: aspeed: everest: Fix bus 15 muxed eeproms
The eeproms on bus 15 muxes were at the wrong addresses.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-6-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Eddie James [Wed, 20 Oct 2021 21:53:20 +0000 (16:53 -0500)]
ARM: dts: aspeed: everest: Add IBM Operation Panel I2C device
Set I2C bus 14 to multi-master mode and add the panel device that will
register the I2C controller as a slave device.
In addition, in early Everest systems, the panel device was behind an
I2C switch, which doesn't work for slave mode. Get it working (albeit
unreliably, since a master transaction might switch the switch at any
moment) by defaulting the switch channel to the one with the panel.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-5-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Eddie James [Wed, 20 Oct 2021 21:53:19 +0000 (16:53 -0500)]
ARM: dts: aspeed: everest: Add I2C switch on bus 8
The switch controls two busses containing some VRMs.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-4-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Eddie James [Wed, 20 Oct 2021 21:53:18 +0000 (16:53 -0500)]
ARM: dts: aspeed: rainier and everest: Remove PCA gpio specification
Specifying gpio nodes under PCA led controllers no longer does anything,
so remove those nodes in the device trees.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-3-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Eddie James [Wed, 20 Oct 2021 21:53:17 +0000 (16:53 -0500)]
ARM: dts: aspeed: p10bmc: Fix ADC iio-hwmon battery node name
In keeping with previous systems, call the iio-hwmon bridge node
"iio-hwmon-battery" to distinguish it as the battery voltage
sensor.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-2-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Arnd Bergmann [Wed, 20 Oct 2021 21:18:00 +0000 (23:18 +0200)]
Merge tag 'omap-for-v5.16/gpmc-signed' of git://git./linux/kernel/git/tmlind/linux-omap into arm/dt
Changes for omap gpmc bindings and devicetree files for v5.16
A series of changes to update the gpmc related bindings to yaml
format, and a few non-urgent dts fixes.
* tag 'omap-for-v5.16/gpmc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap: fix gpmc,mux-add-data type
ARM: dts: omap: Fix boolean properties gpmc,cycle2cycle-{same|diff}csen
dt-bindings: memory-controllers: ti,gpmc: Convert to yaml
dt-bindings: mtd: ti,gpmc-onenand: Convert to yaml
dt-bindings: mtd: ti,gpmc-nand: Convert to yaml
dt-bindings: memory-controllers: Introduce ti,gpmc-child
dt-bindings: net: Remove gpmc-eth.txt
dt-bindings: mtd: Remove gpmc-nor.txt
Link: https://lore.kernel.org/r/pull-1634280279-284035@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 20 Oct 2021 21:17:04 +0000 (23:17 +0200)]
Merge branch 'mstar-dt-next' of https://github.com/linux-chenxing/linux into arm/dt
* 'mstar-dt-next' of https://github.com/linux-chenxing/linux:
ARM: dts: mstar: Mark timer with arm,cpu-registers-not-fw-configured
ARM: dts: mstar: Add rtc device node
Link: https://lore.kernel.org/r/20211020163010.3079-1-romain.perier@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Romain Perier [Thu, 23 Sep 2021 17:07:45 +0000 (19:07 +0200)]
ARM: dts: mstar: Mark timer with arm,cpu-registers-not-fw-configured
The vendor u-boot does not configure the arch timer correctly on
MStar, let Linux do it.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/linux-arm-kernel/20210923170747.5786-2-romain.perier@gmail.com
Romain Perier [Mon, 23 Aug 2021 17:16:13 +0000 (19:16 +0200)]
ARM: dts: mstar: Add rtc device node
This adds the definition of the rtc device node. The RTC being able to
work with the oscillator at 12Mhz for now, it shares the same xtal than
the watchdog.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/all/20210823171613.18941-4-romain.perier@gmail.com
Arnd Bergmann [Wed, 20 Oct 2021 13:45:12 +0000 (15:45 +0200)]
Merge tag 'arm-soc/for-5.15/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This is already in v5.15-rc5, but I'm adding it here as well to get
a clean build of the dts files.
* tag 'arm-soc/for-5.15/devicetree':
ARM: dts: bcm2711-rpi-4-b: Fix usb's unit address
ARM: dts: bcm2711-rpi-4-b: Fix pcie0's unit address formatting
ARM: dts: bcm2711-rpi-4-b: fix sd_io_1v8_reg regulator states
ARM: dts: bcm2711: fix MDIO #address- and #size-cells
ARM: dts: bcm283x: Fix VEC address for BCM2711
Arnd Bergmann [Wed, 20 Oct 2021 13:37:54 +0000 (15:37 +0200)]
Merge tag 'v5.16-rockchip-dts32-2' of git://git./linux/kernel/git/mmind/linux-rockchip into arm/dt
Adapt gpio subnode names to match the yaml binding and removal
of the actually non-matching fallback-string for usb-phys
on rk3066/rk3188 (most-specific compatible is and must always
be used).
* tag 'v5.16-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: remove usb-phy fallback string from rk3066a/rk3188
ARM: dts: rockchip: change gpio nodenames
Link: https://lore.kernel.org/r/3630369.N7QejLDta5@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 20 Oct 2021 13:36:53 +0000 (15:36 +0200)]
Merge tag 'v5.16-rockchip-dts64-2' of git://git./linux/kernel/git/mmind/linux-rockchip into arm/dt
Idle-cooling information for rk3399, rk356x additions (tsadc resets,
i2s, spdif, pwm), rk3368 powerdomains, fixes to make gpio subnodes
compliant with the new pinctrl yaml binding and addition of the
chassis-type for the non-sbc devices.
* tag 'v5.16-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add idle cooling devices to rk3399
arm64: dts: rockchip: fix resets in tsadc node for rk356x
arm64: dts: rockchip: Add analog audio on Quartz64
arm64: dts: rockchip: Add i2s1 on rk356x
arm64: dts: rockchip: change gpio nodenames
arm64: dts: rockchip: add 'chassis-type' property
arm64: dts: rockchip: add powerdomains to rk3368
dt-bindings: arm: rockchip: add rk3368 compatible string to pmu.yaml
arm64: dts: rockchip: enable spdif on Quartz64 A
arm64: dts: rockchip: add spdif node to rk356x
arm64: dts: rockchip: add pwm nodes for rk3568
Link: https://lore.kernel.org/r/4536780.s7XYDJ6uuW@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 20 Oct 2021 13:35:34 +0000 (15:35 +0200)]
Merge tag 'gemini-dts-for-v5.16' of git://git./linux/kernel/git/linusw/linux-nomadik into arm/dt
Gemini changes for the v5.16 kernel cycle:
- Add device trees for Edimax NS2502 and SSI 1328
- Consolidate PCI interrupts
* tag 'gemini-dts-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: gemini: Consolidate PCI interrupt-map properties
ARM: gemini: add device tree for ssi1328
ARM: gemini: add device tree for edimax NS2502
dt-bindings: add vendor prefix for ssi
dt-bindings: add vendor prefix for edimax
ARM: dts: gemini: add labels for USB, IDE, flash and ethernet
Link: https://lore.kernel.org/r/CACRpkdac5Sbt42CtuLMgCazfHdhcP98mEKGjeZ-DVcb=_N90Bg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 20 Oct 2021 13:34:21 +0000 (15:34 +0200)]
Merge tag 'ixp4xx-dts-for-v5.16' of git://git./linux/kernel/git/linusw/linux-nomadik into arm/dt
IXP4xx DTS changes for the v5.16 kernel:
- Add the PTP timesource
- Push down PCI interrupt properties to the individual
board files.
* tag 'ixp4xx-dts-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ixp4xx: Group PCI interrupt properties together
ARM: dts: Add PTP timesource to the IXP456x
Link: https://lore.kernel.org/r/CACRpkdbSJ662h_B9mAGdXWBeq8ZwKTQvSJ7cZ2x2d8UgELP5QA@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 20 Oct 2021 13:28:13 +0000 (15:28 +0200)]
Merge tag 'sunxi-dt-for-5.16-1' of git://git./linux/kernel/git/sunxi/linux into arm/dt
Our usual round of DT patches for the 5.16 merge window, with:
- DT schema fixes
- I2S support for the R40
- HDMI support for the pinetab
- devfreq support for the A64 GPU
* tag 'sunxi-dt-for-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (21 commits)
dt-bindings: interconnect: sunxi: Add R40 MBUS compatible
arm64: dts: allwinner: NanoPi R1S H5: Add generic compatible string for I2C EEPROM
arm64: dts: allwinner: pinetab: Add HDMI support
arm64: dts: allwinner: a64: Add GPU opp table
ARM: dts: sun8i: r40: Add I2S nodes
dt-bindings: sound: sun4i-i2s: add Allwinner R40 I2S compatible
arm64: dts: allwinner: teres-i: Remove wakekup-source from the PMIC
arm64: dts: allwinner: teres-i: Add missing reg
arm64: dts: allwinner: pinetab: Change regulator node name to avoid warning
arm64: dts: allwinner: a100: Fix thermal zone node name
arm64: dts: allwinner: h6: Fix de3 parent clocks ordering
arm64: dts: allwinner: h5: Fix GPU thermal zone node name
ARM: dts: cubieboard4: Remove the dumb-vga-dac compatible
ARM: dts: tbs711: Fix touchscreen compatible
ARM: dts: sunxi: Fix the SPI NOR node names
ARM: dts: sunxi: Fix OPPs node name
ARM: dts: sunxi: Fix OPP arrays
ARM: dts: sunxi: Rename gpio pinctrl names
ARM: dts: sunxi: Rename power-supply names
dt-bindings: sunxi: Add Allwinner A80 PRCM Binding
...
Link: https://lore.kernel.org/r/5cad5ac6-187d-4d36-9437-5821c6e8242d.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 20 Oct 2021 13:19:15 +0000 (15:19 +0200)]
Merge tag 'imx-dt64-5.16' of git://git./linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree changes for 5.16:
- New board support: LX2160A based BlueBox3, S32G2 EVB and RDB2 boards.
- Quite some updates on imx8mq-librem5 board: delay the startup of the
SDIO, add power sequencing for M.2 cards, add wifi regulator, add
panel reset GPIO, fix led_r and led_g pinctrl, etc.
- Fix the SPI chipselect polarity for a couple of i.MX8MM boards.
- Add GPU nodes for i.MX8MM 2D and 3D core.
- Add VPU and DISP blk-ctrl devices for i.MX8MM.
- A series from Michael Walle to LS1028A device trees and add GPU
support.
- Random and small updates on various boards.
* tag 'imx-dt64-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (37 commits)
arm64: dts: imx8mm-kontron: Add support for ultra high speed modes on SD card
arm64: dts: imx8mm-venice-gw7901.dts: disable pgc_gpumix
arm64: dts: imx8mq-librem5: set debounce interval of volume buttons to 50ms
arm64: dts: imx8mq-librem5: Limit the max sdio frequency
arm64: dts: imx8mq-librem5: add power sequencing for M.2 cards
arm64: dts: imx8mq-librem5: delay the startup of the SDIO
arm64: dts: imx8mq-librem5: wire up the wifi regulator
arm64: dts: imx8mq-librem5: Fix led_r and led_g pinctrl assignments
arm64: dts: imx8mq-librem5: add reset gpio to mantix panel description
arm64: dts: imx8mm-kontron: Fix reset delays for ethernet PHY
arm64: dts: imx8mm: add DISP blk-ctrl
arm64: dts: imx8mm: add VPU blk-ctrl
arm64: dts: imx8mm: Add GPU nodes for 2D and 3D core
arm64: dts: imx8mm: put USB controllers into power-domains
arm64: dts: imx8mm: add GPC node
arm64: dts: ls1028a: mark internal links between Felix and ENETC as capable of flow control
arm64: dts: freescale: Fix 'interrupt-map' parent address cells
arm64: dts: ls1028a: use phy-mode instead of phy-connection-type
arm64: dts: ls1028a: move PHY nodes to MDIO controller
arm64: dts: ls1028a: disable usb controller by default
...
Link: https://lore.kernel.org/r/20211016140138.1603-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 20 Oct 2021 13:01:22 +0000 (15:01 +0200)]
Merge tag 'imx-dt-5.16' of git://git./linux/kernel/git/shawnguo/linux into arm/dt
i.MX device tree changes for 5.16:
- New board support: Kobo Libra H2O, Tolino Vision 5, SKOV LT2 and
Colibri i.MX6ULL eMMC variants.
- A series from Fabio Estevam to correct SPI chipselect polarity for
various i.MX6/7 boards.
- A couple of patches from Krzysztof Kozlowski to clean up unsupported
properties from imx6dl-b1x5v2 and imx6dl-prtrvt boards.
- A series from Li Yang to clean up LS1021a based boards and add missing
device nodes.
- A series from Matthias Schiffer to fix typo, add SPI-NOR flash and
partition layout for imx7-tqma7/mba7 boards.
- Fix the schema check errors in i.MX PCIe device nodes.
- Other random and small fix-up and device additions.
* tag 'imx-dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (42 commits)
ARM: dts: ls1021a-tsn: use generic "jedec,spi-nor" compatible for flash
ARM: dts: ls1021a: move thermal-zones node out of soc/
ARM: dts: ls1021a-tsn: remove undocumented property "position" from mma8452 node
ARM: dts: ls1021a-qds: change fpga to simple-mfd device
ARM: dts: ls1021a: add #power-domain-cells for power-controller node
ARM: dts: ls1021a: add #dma-cells to qdma node
ARM: dts: ls1021a: fix memory node for schema check
ARM: dts: ls1021a: remove regulators simple-bus
ARM: dts: ls1021a: disable ifc node by default
ARM: dts: ls1021a: breakup long values in thermal node
ARM: dts: ls1021a: fix board compatible to follow binding schema
ARM: dts: ls1021a: update pcie nodes for dt-schema check
ARM: dts: ls1021a-qds: Add node for QSPI flash
ARM: dts: ls1021a: change to use SPDX identifiers
ARM: dts: ls1021a: change dma channels order to match schema
ARM: dts: ls1021a: remove clock-names property for i2c nodes
ARM: dts: imx6dl-prtrvt: drop undocumented TRF7970A NFC properties
ARM: dts: imx6: phytec: Add gpio pinctrl for i2c bus recovery
ARM: dts: imx6: skov: provide panel support for lt2 variants
ARM: dts: imx6qdl-apalis: Fix typo in ADC comment
...
Link: https://lore.kernel.org/r/20211016140138.1603-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 20 Oct 2021 13:00:08 +0000 (15:00 +0200)]
Merge tag 'imx-bindings-5.16' of git://git./linux/kernel/git/shawnguo/linux into arm/dt
i.MX DT bindings update for 5.16:
- Various board compatible addition: NXP S32G2, LS1021A TSN, Toradex
Colibri i.MX6ULL, LX2160A BlueBox 3 boards.
- Toradex board and module compatibles clean-up.
- Convert fsl-linflexuart bindings to json-schema format and add S32G2
compatible.
- Add bindings and defines for i.MX8MM VPU and DISP blk-ctrl.
* tag 'imx-bindings-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: arm: fsl: add ls1021a-tsn board
dt-bindings: power: imx8mm: add defines for DISP blk-ctrl domains
dt-bindings: soc: add binding for i.MX8MM DISP blk-ctrl
dt-bindings: power: imx8mm: add defines for VPU blk-ctrl domains
dt-bindings: soc: add binding for i.MX8MM VPU blk-ctrl
dt-bindings: arm: fsl: Add E70K02 based ebook readers
dt-bindings: arm: fsl: add toradex,colibri-imx6ull-emmc
dt-bindings: arm: fsl: clean-up all toradex boards/modules
dt-bindings: serial: fsl-linflexuart: add compatible for S32G2
dt-bindings: serial: fsl-linflexuart: convert to json-schema format
dt-bindings: arm: fsl: add NXP S32G2 boards
dt-bindings: arm: fsl: document the LX2160A BlueBox 3 boards
Link: https://lore.kernel.org/r/20211016140138.1603-1-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 20 Oct 2021 12:59:16 +0000 (14:59 +0200)]
Merge tag 'visconti-arm-dt-for-v5.16' of git://git./linux/kernel/git/iwamatsu/linux-visconti into arm/dt
Visconti device tree updates for 5.16
- Add DT support for Toshiba Visconti5 PCIe driver
- Add 150MHz fixed clock to TMPV7708 SoC
- Add DT support for VisROBO VRB boardi
* tag 'visconti-arm-dt-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/iwamatsu/linux-visconti:
arm64: dts: visconti: Add DTS for the VisROBO board
dt-bindings: arm: toshiba: Add the TMPV7708 VisROBO VRB board
arm64: dts: visconti: Add 150MHz fixed clock to TMPV7708 SoC
arm64: dts: visconti: Add PCIe host controller support for TMPV7708 SoC
Link: https://lore.kernel.org/r/YWoH3g7vU1ZEAp+P@toshiba.co.jp
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 20 Oct 2021 12:56:57 +0000 (14:56 +0200)]
Merge tag 'mvebu-dt-5.16-1' of git://git./linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt for 5.16 (part 1)
Add support for Netgear GS110EMX switch (Armada 381 SoC based)
* tag 'mvebu-dt-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: mvebu: add device tree for netgear gs110emx switch
Link: https://lore.kernel.org/r/874k9imeel.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 20 Oct 2021 12:55:31 +0000 (14:55 +0200)]
Merge tag 'mvebu-dt64-5.16-1' of git://git./linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt64 for 5.16 (part 1)
Add support for Globalscale MOCHAbin an Armada 7040 based development
board.
* tag 'mvebu-dt64-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: marvell: add Globalscale MOCHAbin
Link: https://lore.kernel.org/r/877deemefy.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Daniel Lezcano [Fri, 1 Oct 2021 16:17:28 +0000 (18:17 +0200)]
arm64: dts: rockchip: Add idle cooling devices to rk3399
The thermal framework accepts now the cpu idle cooling device as an
alternative when the cpufreq cooling device fails.
Add the node in the DT so the cooling devices will be present and the
platforms can extend the thermal zone definition to add them.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20211001161728.1729664-1-daniel.lezcano@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Sat, 28 Aug 2021 11:12:18 +0000 (13:12 +0200)]
ARM: dts: rockchip: remove usb-phy fallback string from rk3066a/rk3188
With the conversion of rockchip-usb-phy.yaml a long time used fallback
string for rk3066a/rk3188 was added. The linux driver doesn't do much with
the GRF phy address range, however the u-boot driver rockchip_usb2_phy.c
does. The bits in GRF_UOC0_CON2 for rk3066a/rk3188 and rk3288 for example
don't match. Remove the usb-phy fallback string for rk3066a/rk3188
to prevent possible strange side effects.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210828111218.10026-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rob Herring [Tue, 28 Sep 2021 19:17:59 +0000 (14:17 -0500)]
ARM: dts: gemini: Consolidate PCI interrupt-map properties
The Gemini PCI 'interrupt-map' does not vary by board, so let's move
the definition to a common location. This avoids having incomplete
interrupt properties (i.e. #interrupt-cells without interrupt-map).
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rob Herring [Tue, 28 Sep 2021 19:21:22 +0000 (14:21 -0500)]
ARM: dts: ixp4xx: Group PCI interrupt properties together
Move the PCI 'interrupt-map-mask' and '#interrupt-cells' properties
alongside the 'interrupt-map' property in each board dts. This avoids
having incomplete set of interrupt properties which may fail validation.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Arnd Bergmann [Tue, 19 Oct 2021 22:07:02 +0000 (00:07 +0200)]
Merge tag 'stm32-dt-for-v5.16-1' of git://git./linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT for v5.16, round 1
Highlights:
----------
- MPU:
- ST boards:
- Add new stm32mp135f-dk board. It embedds new STM32MP135 SoC,
with 512 MB of DDR3. Several connections are available on this
board:
4*USB2.0, 1*USB2.0 typeC DRD, SDcard, 2*RJ45, HDMI,
Combo Wifi/BT, ...
Only SD card, uart4 (console) and watchdog IPs are enabled in
this tag.
- Change IRQ level for STUSB1600 on DKx boards.
- Fix SAI subclocks range.
- Add ck_usb0_48m clock in USB OHCI node device to match with
STM32MP15 datasheet.
- DH boards:
- Reduce DHCOR SPI NOR frequency to 50 MHz to avoid sporadic issues.
- Fix SAI pin muxing.
- Odyssey:
- Set DCMI pins.
* tag 'stm32-dt-for-v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151
ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
ARM: dts: stm32: fix SAI sub nodes register range
ARM: dts: stm32: fix STUSB1600 Type-C irq level on stm32mp15xx-dkx
ARM: dts: stm32: set the DCMI pins on stm32mp157c-odyssey
ARM: dts: stm32: Reduce DHCOR SPI NOR frequency to 50 MHz
ARM: dts: stm32: add initial support of stm32mp135f-dk board
dt-bindings: stm32: document stm32mp135f-dk board
ARM: dts: stm32: add STM32MP13 SoCs support
Link: https://lore.kernel.org/r/9d52c3e2-a3b9-89f3-1896-7cd3560e7010@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 22:05:08 +0000 (00:05 +0200)]
Merge tag 'renesas-arm-dt-for-v5.16-tag2' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.16 (take two)
- SPI Multi I/O Bus, SDHI, and Ethernet support for the RZ/G2L SoC,
- SPI Multi I/O Bus, camera, and video-on support for the R-Car V3U
SoC,
- SPI FLASH support for the Falcon development board,
- eMMC, microSD, and Ethernet support for the RZ/G2L SMARC EVK
development board,
- 2 GHz High-Performance support for the R-Car H3e-2G, M3e-2G, and
M3Ne-2G SoCs,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.16-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
mailmap: Fix text encoding for Niklas Söderlund
arm64: dts: renesas: rcar-gen3e: Add Cortex-A57 2 GHz opps
arm64: dts: renesas: rzg2l-smarc-som: Enable Ethernet
arm64: dts: renesas: r9a07g044: Add GbEthernet nodes
arm64: dts: renesas: Add ports node to all adv7482 nodes
arm64: dts: renesas: r8a779a0: Add and connect all CSI-2, ISP and VIN nodes
arm64: dts: renesas: rzg2l-smarc: Enable microSD on SMARC platform
arm64: dts: renesas: rzg2l-smarc-som: Enable eMMC on SMARC platform
arm64: dts: renesas: r9a07g044: Add SDHI nodes
arm64: dts: renesas: falcon-cpu: Add SPI flash via RPC
arm64: dts: renesas: r8a779a0: Add RPC node
arm64: dts: renesas: r9a07g044: Add SPI Multi I/O Bus controller node
Link: https://lore.kernel.org/r/cover.1634298094.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 21:58:41 +0000 (23:58 +0200)]
Merge tag 'aspeed-5.16-devicetree' of git://git./linux/kernel/git/joel/bmc into arm/dt
ASPEED device tree updates for 5.15
- New machines:
* TYAN S7106 BMC, a x86 server from about four years ago
- Descriptions for the AST2600 ADC, which now has an upstream driver
- Lots of GPIO line names. The OpenBMC project has adopted a scheme for
naming the lines, and new additions will follow this guide
- New I2C devices for Rainier, Everest, EthanolX, Mt Jade
- Fixes for fp5280g2 which has seen some recent development, including
the addtion of a QEmu machine for testing
* tag 'aspeed-5.16-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc:
ARM: dts: aspeed: fp5280g2: Use the 64M layout
ARM: dts: aspeed: Add TYAN S7106 BMC machine
ARM: dts: aspeed: rainier: Add power-config-full-load gpio
ARM: dts: aspeed: p10bmc: Define secure boot gpio
ARM: dts: aspeed: mtjade: Add some gpios
ARM: dts: aspeed: Add ADC for AST2600 and enable for Rainier and Everest
ARM: dts: everest: Define name for gpio line B6
ARM: dts: everest: Define name for gpio line Q2
ARM: dts: rainier: Define name for gpio line Q2
ARM: dts: everest: Add 'factory-reset-toggle' as GPIOF6
ARM: dts: aspeed: everest: Add I2C bus 15 muxes
ARM: dts: aspeed: rainier: Add system LEDs
ARM: dts: aspeed: amd-ethanolx: Add FRU EEPROM
ARM: dts: fp5280g2: Enable KCS 3 for MCTP binding
Link: https://lore.kernel.org/r/CACPK8XdrMzY9tzdof7KpzxKquTo7GcWW4N9Zqwtmmu73C7htXA@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 21:41:26 +0000 (23:41 +0200)]
Merge tag 'hisi-arm64-dt-for-5.16' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM64: DT: HiSilicon ARM64 DT updates for 5.16
- Add SPMI PMIC support for the Hikey970 board
- Correct the sp805 watchdog compatible string to match the document
- Correct the operating-points table name to match the dtschema
* tag 'hisi-arm64-dt-for-5.16' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisilicon: align operating-points table name with dtschema
arm64: dts: hisilicon: fix arm,sp805 compatible string
arm64: dts: hisilicon: Add support for Hikey 970 PMIC
Link: https://lore.kernel.org/r/6168EB53.60503@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 21:40:40 +0000 (23:40 +0200)]
Merge tag 'ux500-dts-for-v5.16' of git://git./linux/kernel/git/linusw/linux-nomadik into arm/dt
Ux500 DTS updates:
- Flag the janice SPI display lines properly for the right line
semantics.
- Fix some errors in the Skomer regulator configuration.
- Fix some SD card pin configurations on Skomer.
- Assign the Skomer SD card a 300 ms power-on delay.
- Rewrite the battery nodes to use the standard binding
"monitored-battery" as used in the updated bindings, and
provide the right Samsung battery compatibles for the Samsung
phones.
* tag 'ux500-dts-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ux500: Switch battery nodes to standard
ARM: dts: ux500: Skomer eMMC needs 300 ms power on
ARM: dts: ux500: Fix up SD card pin config
ARM: dts: ux500: Skomer regulator fixes
ARM: dts: ux500: Tag Janice display SPI correct
Link: https://lore.kernel.org/r/CACRpkdYf5GwRvG1Gemk4mE+aw6UnAVTY8OudwsVNPQXThHXu6g@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 21:39:15 +0000 (23:39 +0200)]
Merge tag 'arm-soc/for-5.16/devicetree-arm64' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 5.16, please pull the following:
- Rafal updates the BCM4908 DTS files to produce fewer warnings by
fixing the UART clock name, moving the reboot syscon node out of the bus
node, and finally updating the NAND controller node names.
* tag 'arm-soc/for-5.16/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: broadcom: bcm4908: Fix UART clock name
arm64: dts: broadcom: bcm4908: Move reboot syscon out of bus
arm64: dts: broadcom: bcm4908: Fix NAND node name
Link: https://lore.kernel.org/r/20211013174016.831348-2-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 21:35:31 +0000 (23:35 +0200)]
Merge tag 'arm-soc/for-5.16/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.16, please pull the following:
- Matthew provides a set of updates to the Northstar Plus Device Tree
files to fix a number of warnings, and prepare the files to support the
addition of the Cisco Meraki MX64/MX65 wireless controller devices and
finally adds support for those boards.
- Rafal continues to provide updates to the BCM5301X Device Tree files
in order to fix warnings with the various node names, MDIO muxes and
memory nodes. He also adds support for the external switches on the
BCM53573 SoC and adds Tenda AC9 switch ports.
- Christian provides the description of the Ethernet switch ports for
the Cisco Meraki MR32 based on the 53016 SoC
- Arinc adds support for the Asus RT-AC88U device based on the BCM4709
and featuring 8 Ethernet ports over the integrated and the external
Realtek switch (not supported yet)
- Stefan adds support for the Raspberry Pi Compute Module 4 IO board and
does a number of preparatory changes to get there to the Device Tree
files before doing the actual addition
* tag 'arm-soc/for-5.16/devicetree' of https://github.com/Broadcom/stblinux: (31 commits)
arm64: dts: broadcom: Add reference to RPi CM4 IO Board
ARM: dts: Add Raspberry Pi Compute Module 4 IO Board
ARM: dts: Add Raspberry Pi Compute Module 4
dt-bindings: arm: bcm2835: Add Raspberry Pi Compute Module 4
ARM: dts: bcm283x-rpi: Move Wifi/BT into separate dtsi
dt-bindings: display: bcm2835: add optional property power-domains
ARM: dts: BCM5301X: Add DT for Asus RT-AC88U
ARM: BCM53016: MR32: get mac-address from nvmem
ARM: BCM53016: Specify switch ports for Meraki MR32
ARM: dts: BCM53573: Add Tenda AC9 switch ports
ARM: dts: BCM53573: Describe on-SoC BCM53125 rev 4 switch
ARM: dts: BCM5301X: Specify switch ports for more devices
ARM: dts: NSP: Fix MX65 MDIO mux warnings
ARM: dts: NSP: Fix MX64/MX65 eeprom node name
ARM: dts: NSP: Fix MDIO mux node names
ARM: dts: NSP: Fix mpcore, mmc node names
ARM: dts: NSP: Add bcm958623hr board name to dts
ARM: dts: BCM5301X: Fix memory nodes names
ARM: dts: BCM5301X: Fix MDIO mux binding
ARM: dts: BCM5301X: Fix nodes names
...
Link: https://lore.kernel.org/r/20211013174016.831348-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 20:57:36 +0000 (22:57 +0200)]
Merge tag 'samsung-dt64-5.16' of git://git./linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM64 changes for v5.16
1. Match Exynos5433 DTS with dtschema.
2. Add an Exynos Auto v9 SoC and SADK board. The Exynos Auto v9 is a
design for automotive for In-vehicle Infotainments (IVI) and Advanced
Driver-Assistance Systems (ADAS).
This pull request brings very basic support (pinctrl, UART and UFS
storage) with a development SADK (Samsung Automotive Development Kit)
board.
* tag 'samsung-dt64-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: add minimal support for exynosautov9 sadk board
arm64: dts: exynos: add initial support for exynosautov9 SoC
arm64: dts: exynos: add proper comaptible FSYS syscon in Exynos5433
arm64: dts: exynos: align operating-points table name with dtschema in Exynos5433
Link: https://lore.kernel.org/r/20211013162418.43072-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 20:49:26 +0000 (22:49 +0200)]
Merge tag 'samsung-dt-5.16' of git://git./linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.16
Minor cleanups - from undocumented or unused properties, coding style.
* tag 'samsung-dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: use spaces instead of tabs around '='
ARM: dts: exynos: remove unneeded DVS voltages from PMIC on Arndale
ARM: dts: exynos: drop undocumented samsung,sata-freq property in Exynos5250
Link: https://lore.kernel.org/r/20211013162418.43072-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 20:37:09 +0000 (22:37 +0200)]
Merge tag 'qcom-arm64-for-5.16' of git://git./linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 dts updates for v5.16
MSM8916 gained some DT cleanup fixes. The Dragonboard 410c gains updated
firmware paths to the device specific firmware for modem and WiFi, to
allow these to be pushed to linux-next. The Longcheer L8150 gains extcon
support and the interrupt configuration for the accelerometer and
magnetometer are corrected.
MSM8998 gained descriptions for the multimedia clock controller and
iommu, as well as the GPU and its dedicated IOMMU. The QFPROM node is
updated to access the CRC corrected value space, the white LED (for
backlight) found in PMI8998 is described and GCC gains references to the
missing XO and sleep_clk reference clocks.
On top of this initial support for the Fxtec Pro1 QX1000 is added and
then the Sony Xperia XZ1, Xperia XZ1 Compact and the Xperia XZ Premium,
with USB, touchscreen, SDHCI, Bluetooth and vibrator supported.
The Xiaomi Mi 5 and Xiaomi Mi Note 2, based on the MSM8996 platform was
added, with support for frame buffer, GPU, audio, video encoder/decoder
and touchscreen.
The USB controller and PHY found in IPA6018 is described to provide USB
support. IPQ8074 gains a description of the SPMI controller.
The highlight on SC7180 is the introduction of the just released
"Homestar" device. CPU power coefficients are corrected based on
measurements, IMEM is described to ensure that remoteproc relocation
information is carried to post mortem debug tools and a few smaller
fixes are introduced.
The SC7280 gains QSPI, low speed (i2c/spi/uart), GPU, thermal zones,
modem, CPU topology and updated memory map.
On SDM845 the "Limits hardware" is described and increases the
throttling temperature of the hardware from ~70C to 95C, with up to 30%
improvement in benchmarks as result. Relying on hardware throttling and
thermal pressure, the CPU cooling devices are dropped.
The power for the second WiFi channel is properly described for the
Lenovo Yoga C630, to ensure they are both powered.
reboot-modes are defined for the PM660 PMIC, found in SDM630 and SDM660.
Initial support for the Snapdragon 690 (aka SM6350) is introduced, with
support for clocks, regulators, pinctrl, storage, thermal sensors, USB,
SMMU and CPUfreq. On top of this support for the Sony Xperia 10 III is
introduced.
* tag 'qcom-arm64-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (99 commits)
arm64: dts: qcom: sdm630-nile: Correct regulator label name
arm64: dts: qcom: sm6125: Improve indentation of multiline properties
arm64: dts: qcom: msm8916-longcheer-l8150: Use &pm8916_usbin extcon
arm64: dts: qcom: pm8916: Add pm8941-misc extcon for USB detection
arm64: dts: qcom: pm8916: Remove wrong reg-names for rtc@6000
arm64: dts: qcom: sc7280: Update Q6V5 MSS node
arm64: dts: qcom: sc7280: Add Q6V5 MSS node
arm64: dts: qcom: sc7280: Add nodes to boot modem
arm64: dts: qcom: sc7280: Add/Delete/Update reserved memory nodes
arm64: dts: qcom: sc7280: Update reserved memory map
arm64: dts: qcom: msm8998-fxtec-pro1: Add tlmm keyboard keys
arm64: dts: qcom: msm8998-fxtec-pro1: Add Goodix GT9286 touchscreen
arm64: dts: qcom: msm8998-fxtec-pro1: Add physical keyboard leds
arm64: dts: qcom: Add support for MSM8998 F(x)tec Pro1 QX1000
arm64: dts: qcom: msm8916: Fix Secondary MI2S bit clock
arm64: dts: qcom: msm8916-longcheer-l8150: Add missing sensor interrupts
arm64: dts: qcom: sc7180: Add IMEM and pil info regions
arm64: dts: qcom: pm6150l: Add missing include
arm64: dts: qcom: sm6350: Add device tree for Sony Xperia 10 III
arm64: dts: qcom: sm6350: Add apps_smmu and assign iommus prop to USB1
...
Link: https://lore.kernel.org/r/20211012231155.1036519-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 20:36:17 +0000 (22:36 +0200)]
Merge tag 'qcom-dts-for-5.16' of git://git./linux/kernel/git/qcom/linux into arm/dt
Qualcomm DTS updates for v5.16
This extends the previous limited description of MSM8226 with SDHC,
UART, I2C, SCM, SMEM, RPM and basic PMIC definitions. Based on this,
initial support for the LG G Watch R smartwatch is introduced.
APQ8064 gets a couple of DT updates, one which will allow the GPU driver
to drop supporting legacy "opp tables" in the future.
DT bindings and DTS files are updated with additional compatibles, for
completeness.
* tag 'qcom-dts-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
dt-bindings: arm: qcom, add missing devices
ARM: dts: qcom: msm8974: Add xo_board reference clock to DSI0 PHY
ARM: dts: qcom: fill secondary compatible for multiple boards
ARM: dts: qcom: apq8064: adjust memory node according to specs
ARM: dts: qcom: apq8064: Convert adreno from legacy gpu-pwrlevels to opp-v2
ARM: dts: qcom: Add support for LG G Watch R
dt-bindings: arm: qcom: Document APQ8026 SoC binding
ARM: dts: qcom: Add pm8226 PMIC
ARM: dts: qcom: msm8226: Add more SoC bits
dt-bindings: arm: qcom: Document SDX65 platform and boards
Link: https://lore.kernel.org/r/20211012174310.1017857-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 20:34:11 +0000 (22:34 +0200)]
Merge tag 'v5.15-next-dts64' of git://git./linux/kernel/git/matthias.bgg/linux into arm/dt
Biggest change is, that we have now support for a reset controller inside the
mmsys. This goes inhand with changes to the driver, that you will find in the
soc pull request.
Mediatek PCI device tree binding described the root port in a wrong. The IP
actaully implements several root complex with everyone having a single root port.
We need to fix the DT in an incompatible way to describe the HW as it is. This
also fixes a problem that no IRQ bigger then 32 could be handled.
The only public available HW that is affected by this is the BananaPi R64. I'm
not aware that there is a big user base using the upstream kernel. In this
boards PCI is only used for extension cards, so I don't expect any boot problems.
- mt8173: add reset for dsi0 to mmsys
- move dt-bindings reset controller includes to correct folder
- split PCIe node to use new format for mt2712 and mt7622
- mt8183: add audio node to chromebook devices
- mt8192: add clock controller node
* tag 'v5.15-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: dts: mt8183: Add the mmsys reset bit to reset the dsi0
arm64: dts: mt8173: Add the mmsys reset bit to reset the dsi0
dt-bindings: display: mediatek: add dsi reset optional property
dt-bindings: mediatek: Add #reset-cells to mmsys system controller
arm64: dts: mediatek: Move reset controller constants into common location
arm64: dts: mediatek: Split PCIe node for MT2712 and MT7622
arm64: dts: mt8183: add kukui platform audio node
arm64: dts: mt8183: add audio node
arm64: dts: mediatek: Add mt8192 clock controllers
Link: https://lore.kernel.org/r/1a3d63a3-c020-3319-26f6-a2ec338cc42e@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Johan Jonker [Thu, 30 Sep 2021 11:05:17 +0000 (13:05 +0200)]
arm64: dts: rockchip: fix resets in tsadc node for rk356x
In the rockchip_thermal.c driver we now get the resets with
a devm_reset_control_array_get() function, so remove
the reset-names property as it is no longer needed.
Although no longer required in rockchip-thermal.yaml
sort tsadc-apb as first item.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210930110517.14323-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Nicolas Frattaroli [Sat, 16 Oct 2021 10:53:53 +0000 (12:53 +0200)]
arm64: dts: rockchip: Add analog audio on Quartz64
On the Quartz64 Model A, the I2S1 TDM controller is connected
to the rk817 codec in I2S mode. Enabling it and adding the
necessary simple-sound-card and codec nodes allows for analog
audio output on the PINE64 Quartz64 Model A SBC.
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20211016105354.116513-5-frattaroli.nicolas@gmail.com
[some property sorting]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Nicolas Frattaroli [Sat, 16 Oct 2021 10:53:52 +0000 (12:53 +0200)]
arm64: dts: rockchip: Add i2s1 on rk356x
This adds the necessary device tree node on rk3566 and rk3568
to enable the I2S1 TDM audio controller.
I2S0 has not been added, as it is connected to HDMI and there is
no way to test that it's working without a functioning video
clock (read: VOP2 driver).
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20211016105354.116513-4-frattaroli.nicolas@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Thu, 7 Oct 2021 14:40:19 +0000 (16:40 +0200)]
arm64: dts: rockchip: change gpio nodenames
Currently all gpio nodenames are sort of identical to there label.
Nodenames should be of a generic type, so change them all.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20211007144019.7461-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Thu, 7 Oct 2021 14:40:18 +0000 (16:40 +0200)]
ARM: dts: rockchip: change gpio nodenames
Currently all gpio nodenames are sort of identical to there label.
Nodenames should be of a generic type, so change them all.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20211007144019.7461-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Arnaud Ferraris [Sat, 16 Oct 2021 10:20:25 +0000 (12:20 +0200)]
arm64: dts: rockchip: add 'chassis-type' property
A new 'chassis-type' root node property has recently been approved for
the device-tree specification, in order to provide a simple way for
userspace to detect the device form factor and adjust their behavior
accordingly.
This patch fills in this property for end-user devices (such as laptops,
smartphones and tablets) based on Rockchip ARM64 processors.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Link: https://lore.kernel.org/r/20211016102025.23346-5-arnaud.ferraris@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Heiko Stuebner [Sat, 25 Sep 2021 09:04:05 +0000 (11:04 +0200)]
arm64: dts: rockchip: add powerdomains to rk3368
Add the core io-domain node for rk3368.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20210925090405.2601792-3-heiko@sntech.de
Heiko Stuebner [Sat, 25 Sep 2021 09:04:03 +0000 (11:04 +0200)]
dt-bindings: arm: rockchip: add rk3368 compatible string to pmu.yaml
Add the compatible for the pmu mfd on rk3368.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210925090405.2601792-1-heiko@sntech.de
Nicolas Frattaroli [Fri, 15 Oct 2021 11:13:02 +0000 (13:13 +0200)]
arm64: dts: rockchip: enable spdif on Quartz64 A
Add the necessary nodes to enable the spdif output on the
RK3566-Quartz-A board.
Co-developed-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20211015111303.1365328-2-frattaroli.nicolas@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Peter Geis [Fri, 15 Oct 2021 11:13:01 +0000 (13:13 +0200)]
arm64: dts: rockchip: add spdif node to rk356x
This adds the spdif node to the rk356x device tree.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20211015111303.1365328-1-frattaroli.nicolas@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Frieder Schrempf [Fri, 15 Oct 2021 12:48:35 +0000 (14:48 +0200)]
arm64: dts: imx8mm-kontron: Add support for ultra high speed modes on SD card
In order to use ultra high speed modes (UHS) on the SD card slot, we
add matching pinctrls and fix the voltage switching for LDO5 of the
PMIC, by providing the SD_VSEL pin as GPIO to the PMIC driver.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Yuji Ishikawa [Thu, 14 Oct 2021 09:27:03 +0000 (18:27 +0900)]
arm64: dts: visconti: Add DTS for the VisROBO board
This board consists of two boards:
the SoM board (VRC SoM) with the SoC on board, and the board for I/O (VRB).
The functions of each board supported by this update are as follows:
- VRC SoM
- WDT
- GPIO
- SDCard (SPI-MMC mode)
- I2C x1
- VRB board
- VRC SoM
- UART x2
- Ethernet phy
Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Link: https://lore.kernel.org/r/20211014092703.15251-4-yuji2.ishikawa@toshiba.co.jp
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Yuji Ishikawa [Thu, 14 Oct 2021 09:27:02 +0000 (18:27 +0900)]
dt-bindings: arm: toshiba: Add the TMPV7708 VisROBO VRB board
Add an entry for the Toshiba Visconti TMPV7708 VisROBO VRB board
(tmpv7708-visrobo-vrb) to the board/SoC bindings.
Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Link: https://lore.kernel.org/r/20211014092703.15251-3-yuji2.ishikawa@toshiba.co.jp
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Yuji Ishikawa [Thu, 14 Oct 2021 09:27:01 +0000 (18:27 +0900)]
arm64: dts: visconti: Add 150MHz fixed clock to TMPV7708 SoC
This clock source is referred by baudrate generators of
SPI and I2C devices.
Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Link: https://lore.kernel.org/r/20211014092703.15251-2-yuji2.ishikawa@toshiba.co.jp
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Nobuhiro Iwamatsu [Tue, 7 Sep 2021 04:25:00 +0000 (13:25 +0900)]
arm64: dts: visconti: Add PCIe host controller support for TMPV7708 SoC
Add PCIe node and fixed clock for PCIe in TMPV7708's dtsi,
and tmpv7708-rm-mbrc boards's dts.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Link: https://lore.kernel.org/r/20210907042500.1525771-1-nobuhiro1.iwamatsu@toshiba.co.jp
Amelie Delaunay [Wed, 6 Oct 2021 09:53:55 +0000 (11:53 +0200)]
ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151
Referring to the note under USBH reset and clocks chapter of RM0436,
"In order to access USBH_OHCI registers it is necessary to activate the USB
clocks by enabling the PLL controlled by USBPHYC" (ck_usbo_48m).
The point is, when USBPHYC PLL is not enabled, OHCI register access
freezes the resume from STANDBY. It is the case when dual USBH is enabled,
instead of OTG + single USBH.
When OTG is probed, as ck_usbo_48m is USBO clock parent, then USBPHYC PLL
is enabled and OHCI register access is OK.
This patch adds ck_usbo_48m (provided by USBPHYC PLL) as clock of USBH
OHCI, thus USBPHYC PLL will be enabled and OHCI register access will be OK.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Olivier Moysan [Mon, 4 Oct 2021 09:03:04 +0000 (11:03 +0200)]
ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
Fix SAI2A and SAI2B pin muxings for AV96 board on STM32MP15.
Change sai2a-4 & sai2a-5 to sai2a-2 & sai2a-2.
Change sai2a-4 & sai2a-sleep-5 to sai2b-2 & sai2b-sleep-2
Fixes:
dcf185ca8175 ("ARM: dts: stm32: Add alternate pinmux for SAI2 pins on stm32mp15")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Olivier Moysan [Fri, 24 Sep 2021 16:02:21 +0000 (18:02 +0200)]
ARM: dts: stm32: fix SAI sub nodes register range
The STM32 SAI subblocks registers offsets are in the range
0x0004 (SAIx_CR1) to 0x0020 (SAIx_DR).
The corresponding range length is 0x20 instead of 0x1c.
Change reg property accordingly.
Fixes:
5afd65c3a060 ("ARM: dts: stm32: add sai support on stm32mp157c")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Fabrice Gasnier [Tue, 21 Sep 2021 13:34:49 +0000 (15:34 +0200)]
ARM: dts: stm32: fix STUSB1600 Type-C irq level on stm32mp15xx-dkx
STUSB1600 IRQ (Alert pin) is active low (open drain). Interrupts may get
lost currently, so fix the IRQ type.
Fixes:
83686162c0eb ("ARM: dts: stm32: add STUSB1600 Type-C using I2C4 on stm32mp15xx-dkx")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Grzegorz Szymaszek [Thu, 26 Aug 2021 14:45:43 +0000 (16:45 +0200)]
ARM: dts: stm32: set the DCMI pins on stm32mp157c-odyssey
The Seeed Odyssey-STM32MP157C board has a 20-pin DVP camera output. The
DCMI pins used on this output are defined in the pin state definition
&pinctrl/dcmi-1, AKA &dcmi_pins_b (added in mainline commit
02814a41529a55dbfb9fbb2a3728e78e70646ea6). Set these pins as the default
pinctrl of the DCMI peripheral in the board device tree.
The pins are not used for any other purpose, so it seems safe to assume
most users will not need to override (delete) what this patch provides.
status defaults to "disabled", so the peripheral will not be
unnecessarily started. And the users who actually intend to make use of
a camera on the DVP port will have this little part of the configuration
ready.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Mon, 9 Aug 2021 12:13:24 +0000 (14:13 +0200)]
ARM: dts: stm32: Reduce DHCOR SPI NOR frequency to 50 MHz
The SPI NOR is a bit further away from the SoC on DHCOR than on DHCOM,
which causes additional signal delay. At 108 MHz, this delay triggers
a sporadic issue where the first bit of RX data is not received by the
QSPI controller.
There are two options of addressing this problem, either by using the
DLYB block to compensate the extra delay, or by reducing the QSPI bus
clock frequency. The former requires calibration and that is overly
complex, so opt for the second option.
Fixes:
76045bc457104 ("ARM: dts: stm32: Add QSPI NOR on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Alexandre Torgue [Fri, 23 Jul 2021 13:28:10 +0000 (15:28 +0200)]
ARM: dts: stm32: add initial support of stm32mp135f-dk board
Add support of stm32mp135f discovery board (part number: STM32MP135F-DK).
It embeds a STM32MP135F SOC with 512 MB of DDR3.
Several connections are available on this board:
4*USB2.0, 1*USB2.0 typeC DRD, SDcard, 2*RJ45, HDMI, Combo Wifi/BT, ...
Only SD card, uart4 (console) and watchdog IPs are enabled in this commit.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Alexandre Torgue [Fri, 23 Jul 2021 13:28:09 +0000 (15:28 +0200)]
dt-bindings: stm32: document stm32mp135f-dk board
Add new entry for stm32mp135f-dk board.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Alexandre Torgue [Fri, 23 Jul 2021 13:28:08 +0000 (15:28 +0200)]
ARM: dts: stm32: add STM32MP13 SoCs support
Add initial support of STM32MP13 family. The STM32MP13 SoC diversity is
composed by:
-STM32MP131:
-core: 1*CA7, 17*TIMERS, 5*LPTIMERS, DMA/MDMA/DMAMUX
-storage: 3*SDMCC, 1*QSPI, FMC
-com: USB (OHCI/EHCI, OTG), 5*I2C, 5*SPI/I2S, 8*U(S)ART
-audio: 2*SAI
-network: 1*ETH(GMAC)
-STM32MP133: STM32MP131 + 2*CAN, ETH2(GMAC), ADC1
-STM32MP135: STM32MP133 + DCMIPP, LTDC
A second diversity layer exists for security features:
-STM32MP13xY, "Y" gives information:
-Y = A/D means no cryp IP and no secure boot.
-Y = C/F means cryp IP + secure boot.
This commit adds basic peripheral.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Maxime Ripard [Wed, 1 Sep 2021 09:18:25 +0000 (11:18 +0200)]
dt-bindings: interconnect: sunxi: Add R40 MBUS compatible
The R40 MBUS compatible was introduced recently but it was never
documented.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-26-maxime@cerno.tech
Niklas Söderlund [Thu, 14 Oct 2021 21:29:06 +0000 (23:29 +0200)]
mailmap: Fix text encoding for Niklas Söderlund
There are commits that mess up the encoding of 'ö' in Söderlund, add a
correct entry to .mailmap.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20211014212906.2331293-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Li Yang [Tue, 12 Oct 2021 23:58:23 +0000 (18:58 -0500)]
ARM: dts: ls1021a-tsn: use generic "jedec,spi-nor" compatible for flash
We cannot list all the possible chips used in different board revisions,
just use the generic "jedec,spi-nor" compatible instead. This also
fixes dtbs_check error:
['jedec,spi-nor', 's25fl256s1', 's25fl512s'] is too long
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Tue, 12 Oct 2021 23:58:22 +0000 (18:58 -0500)]
ARM: dts: ls1021a: move thermal-zones node out of soc/
This fixes dtbs-check error from simple-bus schema:
soc: thermal-zones: {'type': 'object'} is not allowed for {'cpu-thermal': ..... }
From schema: /home/leo/.local/lib/python3.8/site-packages/dtschema/schemas/simple-bus.yaml
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Tue, 12 Oct 2021 23:58:21 +0000 (18:58 -0500)]
ARM: dts: ls1021a-tsn: remove undocumented property "position" from mma8452 node
Property "postion" is not documented in the mma8452 binding. Remove it
to resolve the error in "make dtbs_check"
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Tue, 12 Oct 2021 23:58:20 +0000 (18:58 -0500)]
ARM: dts: ls1021a-qds: change fpga to simple-mfd device
The FPGA is not really a bus but more like an MFD device. Change the
compatible string from "simple-bus" to "simple-mfd". This also fix a
node name issue with simple-bus schema.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Tue, 12 Oct 2021 23:58:19 +0000 (18:58 -0500)]
ARM: dts: ls1021a: add #power-domain-cells for power-controller node
Add the #power-domain-cells for power-controller node as required by the
schema.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Tue, 12 Oct 2021 23:58:18 +0000 (18:58 -0500)]
ARM: dts: ls1021a: add #dma-cells to qdma node
Add the #dma-cells to align with the dma schema.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Tue, 12 Oct 2021 23:58:17 +0000 (18:58 -0500)]
ARM: dts: ls1021a: fix memory node for schema check
Fix the following error from "make dtbs_check"
memory: False schema does not allow ...
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Tue, 12 Oct 2021 23:58:16 +0000 (18:58 -0500)]
ARM: dts: ls1021a: remove regulators simple-bus
There is no regulator bus in hardware. So move the regulator nodes out
and remove the regulators simple-bus. This also make the dts align with
the simple-bus schema.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Tue, 12 Oct 2021 23:58:15 +0000 (18:58 -0500)]
ARM: dts: ls1021a: disable ifc node by default
Disable the bus in the SoC dtsi file to be enabled only in board dts
files. Also breakup long values in the ifc node to fix dtbs_check.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Tue, 12 Oct 2021 23:58:14 +0000 (18:58 -0500)]
ARM: dts: ls1021a: breakup long values in thermal node
Breakup long values to pass the schema check.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Tue, 12 Oct 2021 23:58:13 +0000 (18:58 -0500)]
ARM: dts: ls1021a: fix board compatible to follow binding schema
Align the compatible strings with the board binding defined in schema
file.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Tue, 12 Oct 2021 23:58:12 +0000 (18:58 -0500)]
ARM: dts: ls1021a: update pcie nodes for dt-schema check
Break up long values to pass dt-schema checks.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Tue, 12 Oct 2021 23:58:11 +0000 (18:58 -0500)]
ARM: dts: ls1021a-qds: Add node for QSPI flash
Add the missing node for qspi flash.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Tue, 12 Oct 2021 23:58:10 +0000 (18:58 -0500)]
ARM: dts: ls1021a: change to use SPDX identifiers
Replace the license text with SPDX identifiers.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Tue, 12 Oct 2021 23:58:09 +0000 (18:58 -0500)]
ARM: dts: ls1021a: change dma channels order to match schema
Although the ordering of DMA channels was not relevant in the txt binding,
it is defined as ordered in the converted yaml schema. Update the dts
to match the order.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Tue, 12 Oct 2021 23:58:08 +0000 (18:58 -0500)]
ARM: dts: ls1021a: remove clock-names property for i2c nodes
The property is optional and not used in matching the clock in driver.
Remove it to avoid dtbs_check issues.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Tue, 12 Oct 2021 23:58:07 +0000 (18:58 -0500)]
dt-bindings: arm: fsl: add ls1021a-tsn board
Add the missing board in the binding docuemnt.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Krzysztof Kozlowski [Sun, 10 Oct 2021 13:32:15 +0000 (15:32 +0200)]
ARM: dts: imx6dl-prtrvt: drop undocumented TRF7970A NFC properties
Neither the bindings nor the device driver use/document
"vin-voltage-override" and "t5t-rmb-extra-byte-quirk" properties.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Wed, 6 Oct 2021 15:38:36 +0000 (08:38 -0700)]
arm64: dts: imx8mm-venice-gw7901.dts: disable pgc_gpumix
Since commit
b21269b12e48 ("arm64: dts: imx8mm: add GPC node") the
GW7901 will hang during kernel init because it does not power the unused
GPU voltage rails on the IMX8MM. Disable pgc_gpumix to work around this.
We also disable the GPU devices that depend on the gpumix power domain
and pgc_gpu to avoid them staying in a probe deferred state forever.
Additionally as the MIPI voltage rail is also not connected on this
board we disable pgc_mipi and disp_blk_ctrl.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Sebastian Krzyszkowiak [Tue, 5 Oct 2021 13:49:02 +0000 (15:49 +0200)]
arm64: dts: imx8mq-librem5: set debounce interval of volume buttons to 50ms
The default of 5ms is too low.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Angus Ainslie [Tue, 5 Oct 2021 13:49:01 +0000 (15:49 +0200)]
arm64: dts: imx8mq-librem5: Limit the max sdio frequency
This is needed for the 1LV Cyress WiFi module to probe correctly.
It also helps improve GNSS sensitivity.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Angus Ainslie [Tue, 5 Oct 2021 13:49:00 +0000 (15:49 +0200)]
arm64: dts: imx8mq-librem5: add power sequencing for M.2 cards
Some wifi cards need reset asserted until after the power supplies
have been enabled.
So wire up the W_DISABLE signal for the SDIO port (WIFI_REG_ON net) and
the BT_REG_ON net to use it for power sequencing.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>