OSDN Git Service
Dan Murphy [Wed, 4 Dec 2019 17:51:12 +0000 (11:51 -0600)]
can: tcan45x: Make wake-up GPIO an optional GPIO
The device has the ability to disable the wake-up pin option. The
wake-up pin can be either force to GND or Vsup and does not have to be
tied to a GPIO. In order for the device to not use the wake-up feature
write the register to disable the WAKE_CONFIG option.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Cc: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Dan Murphy [Wed, 4 Dec 2019 17:51:11 +0000 (11:51 -0600)]
dt-bindings: tcan4x5x: Make wake-gpio an optional gpio
The wake-up of the device can be configured as an optional feature of
the device. Move the wake-up gpio from a requried property to an
optional property.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Cc: Rob Herring <robh@kernel.org>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sean Nyekjaer [Fri, 6 Dec 2019 15:29:23 +0000 (16:29 +0100)]
dt-bindings: can: tcan4x5x: reset pin is active high
Change the reset pin example to active high to be in line with
the datasheet
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sean Nyekjaer [Fri, 6 Dec 2019 15:29:22 +0000 (16:29 +0100)]
can: m_can: tcan4x5x: add required delay after reset
According to section "8.3.8 RST Pin" in the datasheet we are required to
wait >700us after the device is reset.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.4
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Joakim Zhang [Wed, 4 Dec 2019 11:36:14 +0000 (11:36 +0000)]
can: flexcan: poll MCR_LPM_ACK instead of GPR ACK for stop mode acknowledgment
Stop Mode is entered when Stop Mode is requested at chip level and
MCR[LPM_ACK] is asserted by the FlexCAN.
Double check with IP owner, the MCR[LPM_ACK] bit should be polled for
stop mode acknowledgment, not the acknowledgment from chip level which
is used to gate flexcan clocks.
This patch depends on:
b7603d080ffc ("can: flexcan: add low power enter/exit acknowledgment helper")
Fixes:
5f186c257fa4 (can: flexcan: fix stop mode acknowledgment)
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Joakim Zhang [Wed, 4 Dec 2019 11:36:11 +0000 (11:36 +0000)]
can: flexcan: add low power enter/exit acknowledgment helper
The MCR[LPMACK] read-only bit indicates that FlexCAN is in a lower-power
mode (Disabled mode, Doze mode, Stop mode).
The CPU can poll this bit to know when FlexCAN has actually entered low
power mode. The low power enter/exit acknowledgment helper will reduce
code duplication for disabled mode, doze mode and stop mode.
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sean Nyekjaer [Wed, 4 Dec 2019 11:36:06 +0000 (11:36 +0000)]
can: flexcan: fix possible deadlock and out-of-order reception after wakeup
When suspending, and there is still CAN traffic on the interfaces the
flexcan immediately wakes the platform again. As it should :-). But it
throws this error msg:
[ 3169.378661] PM: noirq suspend of devices failed
On the way down to suspend the interface that throws the error message
calls flexcan_suspend() but fails to call flexcan_noirq_suspend(). That
means flexcan_enter_stop_mode() is called, but on the way out of suspend
the driver only calls flexcan_resume() and skips flexcan_noirq_resume(),
thus it doesn't call flexcan_exit_stop_mode(). This leaves the flexcan
in stop mode, and with the current driver it can't recover from this
even with a soft reboot, it requires a hard reboot.
This patch fixes the deadlock when using self wakeup, by calling
flexcan_exit_stop_mode() from flexcan_resume() instead of
flexcan_noirq_resume().
This also fixes another issue: CAN frames are received out-of-order in
first IRQ handler run after wakeup.
The problem is that the wakeup latency from frame reception to the IRQ
handler (where the CAN frames are sorted by timestamp) is much bigger
than the time stamp counter wrap around time. This means it's
impossible to sort the CAN frames by timestamp.
The reason is that the controller exits stop mode during noirq resume,
which means it receives frames immediately, but interrupt handling is
still not possible.
So exit stop mode during resume stage instead of noirq resume fixes this
issue.
Fixes:
de3578c198c6 ("can: flexcan: add self wakeup support")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Srinivas Neeli [Tue, 3 Dec 2019 12:16:36 +0000 (17:46 +0530)]
can: xilinx_can: Fix missing Rx can packets on CANFD2.0
CANFD2.0 core uses BRAM for storing acceptance filter ID(AFID) and MASK
(AFMASK)registers. So by default AFID and AFMASK registers contain random
data. Due to random data, we are not able to receive all CAN ids.
Initializing AFID and AFMASK registers with Zero before enabling
acceptance filter to receive all packets irrespective of ID and Mask.
Fixes:
0db9071353a0 ("can: xilinx: add can 2.0 support")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Thu, 21 Nov 2019 09:47:50 +0000 (10:47 +0100)]
can: j1939: fix address claim code example
During development the define J1939_PGN_ADDRESS_REQUEST was renamed to
J1939_PGN_REQUEST. It was forgotten to adjust the documentation
accordingly.
This patch fixes the name of the symbol.
Reported-by: https://github.com/linux-can/can-utils/issues/159#issuecomment-556538798
Fixes:
9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oleksij Rempel [Fri, 6 Dec 2019 14:18:35 +0000 (15:18 +0100)]
can: j1939: j1939_sk_bind(): take priv after lock is held
syzbot reproduced following crash:
===============================================================================
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 9844 Comm: syz-executor.0 Not tainted 5.4.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:__lock_acquire+0x1254/0x4a00 kernel/locking/lockdep.c:3828
Code: 00 0f 85 96 24 00 00 48 81 c4 f0 00 00 00 5b 41 5c 41 5d 41 5e 41
5f 5d c3 48 b8 00 00 00 00 00 fc ff df 4c 89 f2 48 c1 ea 03 <80> 3c 02
00 0f 85 0b 28 00 00 49 81 3e 20 19 78 8a 0f 84 5f ee ff
RSP: 0018:
ffff888099c3fb48 EFLAGS:
00010006
RAX:
dffffc0000000000 RBX:
0000000000000000 RCX:
0000000000000000
RDX:
0000000000000218 RSI:
0000000000000000 RDI:
0000000000000001
RBP:
ffff888099c3fc60 R08:
0000000000000001 R09:
0000000000000001
R10:
fffffbfff146e1d0 R11:
ffff888098720400 R12:
00000000000010c0
R13:
0000000000000000 R14:
00000000000010c0 R15:
0000000000000000
FS:
00007f0559e98700(0000) GS:
ffff8880ae800000(0000)
knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007fe4d89e0000 CR3:
0000000099606000 CR4:
00000000001406f0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
lock_acquire+0x190/0x410 kernel/locking/lockdep.c:4485
__raw_spin_lock_bh include/linux/spinlock_api_smp.h:135 [inline]
_raw_spin_lock_bh+0x33/0x50 kernel/locking/spinlock.c:175
spin_lock_bh include/linux/spinlock.h:343 [inline]
j1939_jsk_del+0x32/0x210 net/can/j1939/socket.c:89
j1939_sk_bind+0x2ea/0x8f0 net/can/j1939/socket.c:448
__sys_bind+0x239/0x290 net/socket.c:1648
__do_sys_bind net/socket.c:1659 [inline]
__se_sys_bind net/socket.c:1657 [inline]
__x64_sys_bind+0x73/0xb0 net/socket.c:1657
do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x45a679
Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89
f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01
f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007f0559e97c78 EFLAGS:
00000246 ORIG_RAX:
0000000000000031
RAX:
ffffffffffffffda RBX:
0000000000000003 RCX:
000000000045a679
RDX:
0000000000000018 RSI:
0000000020000240 RDI:
0000000000000003
RBP:
000000000075bf20 R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000246 R12:
00007f0559e986d4
R13:
00000000004c09e9 R14:
00000000004d37d0 R15:
00000000ffffffff
Modules linked in:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 9844 at kernel/locking/mutex.c:1419
mutex_trylock+0x279/0x2f0 kernel/locking/mutex.c:1427
===============================================================================
This issues was caused by null pointer deference. Where j1939_sk_bind()
was using currently not existing priv.
Possible scenario may look as following:
cpu0 cpu1
bind()
bind()
j1939_sk_bind()
j1939_sk_bind()
priv = jsk->priv;
priv = jsk->priv;
lock_sock(sock->sk);
priv = j1939_netdev_start(ndev);
j1939_jsk_add(priv, jsk);
jsk->priv = priv;
relase_sock(sock->sk);
lock_sock(sock->sk);
j1939_jsk_del(priv, jsk);
..... ooops ......
With this patch we move "priv = jsk->priv;" after the lock, to avoid
assigning of wrong priv pointer.
Reported-by: syzbot+99e9e1b200a1e363237d@syzkaller.appspotmail.com
Fixes:
9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.4
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Dan Murphy [Thu, 5 Dec 2019 17:57:16 +0000 (11:57 -0600)]
MAINTAINERS: Add myself as a maintainer for TCAN4x5x
Adding myself to support the TI TCAN4X5X SPI CAN device.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Dan Murphy [Thu, 5 Dec 2019 17:57:15 +0000 (11:57 -0600)]
MAINTAINERS: Add myself as a maintainer for MMIO m_can
Since I refactored the code to create a m_can framework and we
have a MMIO MCAN IP as well add myself to help maintain the code.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Heiner Kallweit [Sat, 7 Dec 2019 21:21:52 +0000 (22:21 +0100)]
r8169: fix rtl_hw_jumbo_disable for RTL8168evl
In referenced fix we removed the RTL8168e-specific jumbo config for
RTL8168evl in rtl_hw_jumbo_enable(). We have to do the same in
rtl_hw_jumbo_disable().
v2: fix referenced commit id
Fixes:
14012c9f3bb9 ("r8169: fix jumbo configuration for RTL8168evl")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 7 Dec 2019 19:34:45 +0000 (11:34 -0800)]
net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
Use the new tcf_proto_check_kind() helper to make sure user
provided value is well formed.
BUG: KMSAN: uninit-value in string_nocheck lib/vsprintf.c:606 [inline]
BUG: KMSAN: uninit-value in string+0x4be/0x600 lib/vsprintf.c:668
CPU: 0 PID: 12358 Comm: syz-executor.1 Not tainted 5.4.0-rc8-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x220 lib/dump_stack.c:118
kmsan_report+0x128/0x220 mm/kmsan/kmsan_report.c:108
__msan_warning+0x64/0xc0 mm/kmsan/kmsan_instr.c:245
string_nocheck lib/vsprintf.c:606 [inline]
string+0x4be/0x600 lib/vsprintf.c:668
vsnprintf+0x218f/0x3210 lib/vsprintf.c:2510
__request_module+0x2b1/0x11c0 kernel/kmod.c:143
tcf_proto_lookup_ops+0x171/0x700 net/sched/cls_api.c:139
tc_chain_tmplt_add net/sched/cls_api.c:2730 [inline]
tc_ctl_chain+0x1904/0x38a0 net/sched/cls_api.c:2850
rtnetlink_rcv_msg+0x115a/0x1580 net/core/rtnetlink.c:5224
netlink_rcv_skb+0x431/0x620 net/netlink/af_netlink.c:2477
rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5242
netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
netlink_unicast+0xf3e/0x1020 net/netlink/af_netlink.c:1328
netlink_sendmsg+0x110f/0x1330 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:637 [inline]
sock_sendmsg net/socket.c:657 [inline]
___sys_sendmsg+0x14ff/0x1590 net/socket.c:2311
__sys_sendmsg net/socket.c:2356 [inline]
__do_sys_sendmsg net/socket.c:2365 [inline]
__se_sys_sendmsg+0x305/0x460 net/socket.c:2363
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2363
do_syscall_64+0xb6/0x160 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x45a649
Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007f0790795c78 EFLAGS:
00000246 ORIG_RAX:
000000000000002e
RAX:
ffffffffffffffda RBX:
0000000000000003 RCX:
000000000045a649
RDX:
0000000000000000 RSI:
0000000020000300 RDI:
0000000000000006
RBP:
000000000075bfc8 R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000246 R12:
00007f07907966d4
R13:
00000000004c8db5 R14:
00000000004df630 R15:
00000000ffffffff
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:149 [inline]
kmsan_internal_poison_shadow+0x5c/0x110 mm/kmsan/kmsan.c:132
kmsan_slab_alloc+0x97/0x100 mm/kmsan/kmsan_hooks.c:86
slab_alloc_node mm/slub.c:2773 [inline]
__kmalloc_node_track_caller+0xe27/0x11a0 mm/slub.c:4381
__kmalloc_reserve net/core/skbuff.c:141 [inline]
__alloc_skb+0x306/0xa10 net/core/skbuff.c:209
alloc_skb include/linux/skbuff.h:1049 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1174 [inline]
netlink_sendmsg+0x783/0x1330 net/netlink/af_netlink.c:1892
sock_sendmsg_nosec net/socket.c:637 [inline]
sock_sendmsg net/socket.c:657 [inline]
___sys_sendmsg+0x14ff/0x1590 net/socket.c:2311
__sys_sendmsg net/socket.c:2356 [inline]
__do_sys_sendmsg net/socket.c:2365 [inline]
__se_sys_sendmsg+0x305/0x460 net/socket.c:2363
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2363
do_syscall_64+0xb6/0x160 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes:
6f96c3c6904c ("net_sched: fix backward compatibility for TCA_KIND")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Fri, 6 Dec 2019 22:27:15 +0000 (23:27 +0100)]
r8169: add missing RX enabling for WoL on RTL8125
RTL8125 also requires to enable RX for WoL.
v2: add missing Fixes tag
Fixes:
f1bce4ad2f1c ("r8169: add support for RTL8125")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Fri, 6 Dec 2019 14:39:12 +0000 (15:39 +0100)]
vhost/vsock: accept only packets with the right dst_cid
When we receive a new packet from the guest, we check if the
src_cid is correct, but we forgot to check the dst_cid.
The host should accept only packets where dst_cid is
equal to the host CID.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Fri, 6 Dec 2019 12:34:32 +0000 (14:34 +0200)]
net: phy: dp83867: fix hfs boot in rgmii mode
The commit
ef87f7da6b28 ("net: phy: dp83867: move dt parsing to probe")
causes regression on TI dra71x-evm and dra72x-evm, where DP83867 PHY is
used in "rgmii-id" mode - the networking stops working.
Unfortunately, it's not enough to just move DT parsing code to .probe() as
it depends on phydev->interface value, which is set to correct value abter
the .probe() is completed and before calling .config_init(). So, RGMII
configuration can't be loaded from DT.
To fix and issue
- move RGMII validation code to .config_init()
- parse RGMII parameters in dp83867_of_init(), but consider them as
optional.
Fixes:
ef87f7da6b28 ("net: phy: dp83867: move dt parsing to probe")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Fri, 6 Dec 2019 12:28:20 +0000 (14:28 +0200)]
net: ethernet: ti: cpsw: fix extra rx interrupt
Now RX interrupt is triggered twice every time, because in
cpsw_rx_interrupt() it is asked first and then disabled. So there will be
pending interrupt always, when RX interrupt is enabled again in NAPI
handler.
Fix it by first disabling IRQ and then do ask.
Fixes:
870915feabdc ("drivers: net: cpsw: remove disable_irq/enable_irq as irq can be masked from cpsw itself")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 6 Dec 2019 04:43:46 +0000 (20:43 -0800)]
inet: protect against too small mtu values.
syzbot was once again able to crash a host by setting a very small mtu
on loopback device.
Let's make inetdev_valid_mtu() available in include/net/ip.h,
and use it in ip_setup_cork(), so that we protect both ip_append_page()
and __ip_append_data()
Also add a READ_ONCE() when the device mtu is read.
Pairs this lockless read with one WRITE_ONCE() in __dev_set_mtu(),
even if other code paths might write over this field.
Add a big comment in include/linux/netdevice.h about dev->mtu
needing READ_ONCE()/WRITE_ONCE() annotations.
Hopefully we will add the missing ones in followup patches.
[1]
refcount_t: saturated; leaking memory.
WARNING: CPU: 0 PID: 9464 at lib/refcount.c:22 refcount_warn_saturate+0x138/0x1f0 lib/refcount.c:22
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 9464 Comm: syz-executor850 Not tainted 5.4.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
panic+0x2e3/0x75c kernel/panic.c:221
__warn.cold+0x2f/0x3e kernel/panic.c:582
report_bug+0x289/0x300 lib/bug.c:195
fixup_bug arch/x86/kernel/traps.c:174 [inline]
fixup_bug arch/x86/kernel/traps.c:169 [inline]
do_error_trap+0x11b/0x200 arch/x86/kernel/traps.c:267
do_invalid_op+0x37/0x50 arch/x86/kernel/traps.c:286
invalid_op+0x23/0x30 arch/x86/entry/entry_64.S:1027
RIP: 0010:refcount_warn_saturate+0x138/0x1f0 lib/refcount.c:22
Code: 06 31 ff 89 de e8 c8 f5 e6 fd 84 db 0f 85 6f ff ff ff e8 7b f4 e6 fd 48 c7 c7 e0 71 4f 88 c6 05 56 a6 a4 06 01 e8 c7 a8 b7 fd <0f> 0b e9 50 ff ff ff e8 5c f4 e6 fd 0f b6 1d 3d a6 a4 06 31 ff 89
RSP: 0018:
ffff88809689f550 EFLAGS:
00010286
RAX:
0000000000000000 RBX:
0000000000000000 RCX:
0000000000000000
RDX:
0000000000000000 RSI:
ffffffff815e4336 RDI:
ffffed1012d13e9c
RBP:
ffff88809689f560 R08:
ffff88809c50a3c0 R09:
fffffbfff15d31b1
R10:
fffffbfff15d31b0 R11:
ffffffff8ae98d87 R12:
0000000000000001
R13:
0000000000040100 R14:
ffff888099041104 R15:
ffff888218d96e40
refcount_add include/linux/refcount.h:193 [inline]
skb_set_owner_w+0x2b6/0x410 net/core/sock.c:1999
sock_wmalloc+0xf1/0x120 net/core/sock.c:2096
ip_append_page+0x7ef/0x1190 net/ipv4/ip_output.c:1383
udp_sendpage+0x1c7/0x480 net/ipv4/udp.c:1276
inet_sendpage+0xdb/0x150 net/ipv4/af_inet.c:821
kernel_sendpage+0x92/0xf0 net/socket.c:3794
sock_sendpage+0x8b/0xc0 net/socket.c:936
pipe_to_sendpage+0x2da/0x3c0 fs/splice.c:458
splice_from_pipe_feed fs/splice.c:512 [inline]
__splice_from_pipe+0x3ee/0x7c0 fs/splice.c:636
splice_from_pipe+0x108/0x170 fs/splice.c:671
generic_splice_sendpage+0x3c/0x50 fs/splice.c:842
do_splice_from fs/splice.c:861 [inline]
direct_splice_actor+0x123/0x190 fs/splice.c:1035
splice_direct_to_actor+0x3b4/0xa30 fs/splice.c:990
do_splice_direct+0x1da/0x2a0 fs/splice.c:1078
do_sendfile+0x597/0xd00 fs/read_write.c:1464
__do_sys_sendfile64 fs/read_write.c:1525 [inline]
__se_sys_sendfile64 fs/read_write.c:1511 [inline]
__x64_sys_sendfile64+0x1dd/0x220 fs/read_write.c:1511
do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x441409
Code: e8 ac e8 ff ff 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb 08 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007fffb64c4f78 EFLAGS:
00000246 ORIG_RAX:
0000000000000028
RAX:
ffffffffffffffda RBX:
0000000000000000 RCX:
0000000000441409
RDX:
0000000000000000 RSI:
0000000000000006 RDI:
0000000000000005
RBP:
0000000000073b8a R08:
0000000000000010 R09:
0000000000000010
R10:
0000000000010001 R11:
0000000000000246 R12:
0000000000402180
R13:
0000000000402210 R14:
0000000000000000 R15:
0000000000000000
Kernel Offset: disabled
Rebooting in 86400 seconds..
Fixes:
1470ddf7f8ce ("inet: Remove explicit write references to sk/inet in ip_append_data")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Fri, 6 Dec 2019 03:39:02 +0000 (19:39 -0800)]
gre: refetch erspan header from skb->data after pskb_may_pull()
After pskb_may_pull() we should always refetch the header
pointers from the skb->data in case it got reallocated.
In gre_parse_header(), the erspan header is still fetched
from the 'options' pointer which is fetched before
pskb_may_pull().
Found this during code review of a KMSAN bug report.
Fixes:
cb73ee40b1b3 ("net: ip_gre: use erspan key field for tunnel lookup")
Cc: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: William Tu <u9012063@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aditya Pakki [Thu, 5 Dec 2019 23:04:49 +0000 (17:04 -0600)]
pppoe: remove redundant BUG_ON() check in pppoe_pernet
Passing NULL to pppoe_pernet causes a crash via BUG_ON.
Dereferencing net in net_generici() also has the same effect. This patch
removes the redundant BUG_ON check on the same parameter.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 7 Dec 2019 05:05:14 +0000 (21:05 -0800)]
Merge branch 'tcp-fix-handling-of-stale-syncookies-timestamps'
Guillaume Nault says:
====================
tcp: fix handling of stale syncookies timestamps
The synflood timestamps (->ts_recent_stamp and ->synq_overflow_ts) are
only refreshed when the syncookie protection triggers. Therefore, their
value can become very far apart from jiffies if no synflood happens for
a long time.
If jiffies grows too much and wraps while the synflood timestamp isn't
refreshed, then time_after32() might consider the later to be in the
future. This can trick tcp_synq_no_recent_overflow() into returning
erroneous values and rejecting valid ACKs.
Patch 1 handles the case of ACKs using legitimate syncookies.
Patch 2 handles the case of stray ACKs.
Patch 3 annotates lockless timestamp operations with READ_ONCE() and
WRITE_ONCE().
Changes from v3:
- Fix description of time_between32() (found by Eric Dumazet).
- Use more accurate Fixes tag in patch 3 (suggested by Eric Dumazet).
Changes from v2:
- Define and use time_between32() instead of a pair of
time_before32/time_after32 (suggested by Eric Dumazet).
- Use 'last_overflow - HZ' as lower bound in
tcp_synq_no_recent_overflow(), to accommodate for concurrent
timestamp updates (found by Eric Dumazet).
- Add a third patch to annotate lockless accesses to .ts_recent_stamp.
Changes from v1:
- Initialising timestamps at socket creation time is not enough
because jiffies wraps in 24 days with HZ=1000 (Eric Dumazet).
Handle stale timestamps in tcp_synq_overflow() and
tcp_synq_no_recent_overflow() instead.
- Rework commit description.
- Add a second patch to handle the case of stray ACKs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 6 Dec 2019 11:38:49 +0000 (12:38 +0100)]
tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
Syncookies borrow the ->rx_opt.ts_recent_stamp field to store the
timestamp of the last synflood. Protect them with READ_ONCE() and
WRITE_ONCE() since reads and writes aren't serialised.
Use of .rx_opt.ts_recent_stamp for storing the synflood timestamp was
introduced by
a0f82f64e269 ("syncookies: remove last_synq_overflow from
struct tcp_sock"). But unprotected accesses were already there when
timestamp was stored in .last_synq_overflow.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 6 Dec 2019 11:38:43 +0000 (12:38 +0100)]
tcp: tighten acceptance of ACKs not matching a child socket
When no synflood occurs, the synflood timestamp isn't updated.
Therefore it can be so old that time_after32() can consider it to be
in the future.
That's a problem for tcp_synq_no_recent_overflow() as it may report
that a recent overflow occurred while, in fact, it's just that jiffies
has grown past 'last_overflow' + TCP_SYNCOOKIE_VALID + 2^31.
Spurious detection of recent overflows lead to extra syncookie
verification in cookie_v[46]_check(). At that point, the verification
should fail and the packet dropped. But we should have dropped the
packet earlier as we didn't even send a syncookie.
Let's refine tcp_synq_no_recent_overflow() to report a recent overflow
only if jiffies is within the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval. This
way, no spurious recent overflow is reported when jiffies wraps and
'last_overflow' becomes in the future from the point of view of
time_after32().
However, if jiffies wraps and enters the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval (with
'last_overflow' being a stale synflood timestamp), then
tcp_synq_no_recent_overflow() still erroneously reports an
overflow. In such cases, we have to rely on syncookie verification
to drop the packet. We unfortunately have no way to differentiate
between a fresh and a stale syncookie timestamp.
In practice, using last_overflow as lower bound is problematic.
If the synflood timestamp is concurrently updated between the time
we read jiffies and the moment we store the timestamp in
'last_overflow', then 'now' becomes smaller than 'last_overflow' and
tcp_synq_no_recent_overflow() returns true, potentially dropping a
valid syncookie.
Reading jiffies after loading the timestamp could fix the problem,
but that'd require a memory barrier. Let's just accommodate for
potential timestamp growth instead and extend the interval using
'last_overflow - HZ' as lower bound.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 6 Dec 2019 11:38:36 +0000 (12:38 +0100)]
tcp: fix rejected syncookies due to stale timestamps
If no synflood happens for a long enough period of time, then the
synflood timestamp isn't refreshed and jiffies can advance so much
that time_after32() can't accurately compare them any more.
Therefore, we can end up in a situation where time_after32(now,
last_overflow + HZ) returns false, just because these two values are
too far apart. In that case, the synflood timestamp isn't updated as
it should be, which can trick tcp_synq_no_recent_overflow() into
rejecting valid syncookies.
For example, let's consider the following scenario on a system
with HZ=1000:
* The synflood timestamp is 0, either because that's the timestamp
of the last synflood or, more commonly, because we're working with
a freshly created socket.
* We receive a new SYN, which triggers synflood protection. Let's say
that this happens when jiffies ==
2147484649 (that is,
'synflood timestamp' + HZ + 2^31 + 1).
* Then tcp_synq_overflow() doesn't update the synflood timestamp,
because time_after32(
2147484649, 1000) returns false.
With:
-
2147484649: the value of jiffies, aka. 'now'.
- 1000: the value of 'last_overflow' + HZ.
* A bit later, we receive the ACK completing the 3WHS. But
cookie_v[46]_check() rejects it because tcp_synq_no_recent_overflow()
says that we're not under synflood. That's because
time_after32(
2147484649, 120000) returns false.
With:
-
2147484649: the value of jiffies, aka. 'now'.
- 120000: the value of 'last_overflow' + TCP_SYNCOOKIE_VALID.
Of course, in reality jiffies would have increased a bit, but this
condition will last for the next 119 seconds, which is far enough
to accommodate for jiffie's growth.
Fix this by updating the overflow timestamp whenever jiffies isn't
within the [last_overflow, last_overflow + HZ] range. That shouldn't
have any performance impact since the update still happens at most once
per second.
Now we're guaranteed to have fresh timestamps while under synflood, so
tcp_synq_no_recent_overflow() can safely use it with time_after32() in
such situations.
Stale timestamps can still make tcp_synq_no_recent_overflow() return
the wrong verdict when not under synflood. This will be handled in the
next patch.
For 64 bits architectures, the problem was introduced with the
conversion of ->tw_ts_recent_stamp to 32 bits integer by commit
cca9bab1b72c ("tcp: use monotonic timestamps for PAWS").
The problem has always been there on 32 bits architectures.
Fixes:
cca9bab1b72c ("tcp: use monotonic timestamps for PAWS")
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 7 Dec 2019 04:52:16 +0000 (20:52 -0800)]
Merge tag 'mlx5-fixes-2019-12-05' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-12-05
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.19:
('net/mlx5e: Query global pause state before setting prio2buffer')
For -stable v5.3
('net/mlx5e: Fix SFF 8472 eeprom length')
('net/mlx5e: Fix translation of link mode into speed')
('net/mlx5e: Fix freeing flow with kfree() and not kvfree()')
('net/mlx5e: ethtool, Fix analysis of speed setting')
('net/mlx5e: Fix TXQ indices to be sequential')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruno Carneiro da Cunha [Thu, 5 Dec 2019 20:16:26 +0000 (17:16 -0300)]
lpc_eth: kernel BUG on remove
We may have found a bug in the nxp/lpc_eth.c driver. The function
platform_set_drvdata() is called twice, the second time it is called,
in lpc_mii_init(), it overwrites the struct net_device which should be
at pdev->dev->driver_data with pldat->mii_bus. When trying to remove
the driver, in lpc_eth_drv_remove(), platform_get_drvdata() will
return the pldat->mii_bus pointer and try to use it as a struct
net_device pointer. This causes unregister_netdev to segfault and
generate a kernel BUG. Is this reproducible?
Signed-off-by: Daniel Martinez <linux@danielsmartinez.com>
Signed-off-by: Bruno Carneiro da Cunha <brunocarneirodacunha@usp.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 5 Dec 2019 18:10:15 +0000 (10:10 -0800)]
tcp: md5: fix potential overestimation of TCP option space
Back in 2008, Adam Langley fixed the corner case of packets for flows
having all of the following options : MD5 TS SACK
Since MD5 needs 20 bytes, and TS needs 12 bytes, no sack block
can be cooked from the remaining 8 bytes.
tcp_established_options() correctly sets opts->num_sack_blocks
to zero, but returns 36 instead of 32.
This means TCP cooks packets with 4 extra bytes at the end
of options, containing unitialized bytes.
Fixes:
33ad798c924b ("tcp: options clean up")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 7 Dec 2019 04:45:09 +0000 (20:45 -0800)]
Merge branch 'net-tc-indirect-block-relay'
John Hurley says:
====================
Ensure egress un/bind are relayed with indirect blocks
On register and unregister for indirect blocks, a command is called that
sends a bind/unbind event to the registering driver. This command assumes
that the bind to indirect block will be on ingress. However, drivers such
as NFP have allowed binding to clsact qdiscs as well as ingress qdiscs
from mainline Linux 5.2. A clsact qdisc binds to an ingress and an egress
block.
Rather than assuming that an indirect bind is always ingress, modify the
function names to remove the ingress tag (patch 1). In cls_api, which is
used by NFP to offload TC flower, generate bind/unbind message for both
ingress and egress blocks on the event of indirectly
registering/unregistering from that block. Doing so mimics the behaviour
of both ingress and clsact qdiscs on initialise and destroy.
This now ensures that drivers such as NFP receive the correct binder type
for the indirect block registration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Thu, 5 Dec 2019 17:03:35 +0000 (17:03 +0000)]
net: sched: allow indirect blocks to bind to clsact in TC
When a device is bound to a clsact qdisc, bind events are triggered to
registered drivers for both ingress and egress. However, if a driver
registers to such a device using the indirect block routines then it is
assumed that it is only interested in ingress offload and so only replays
ingress bind/unbind messages.
The NFP driver supports the offload of some egress filters when
registering to a block with qdisc of type clsact. However, on unregister,
if the block is still active, it will not receive an unbind egress
notification which can prevent proper cleanup of other registered
callbacks.
Modify the indirect block callback command in TC to send messages of
ingress and/or egress bind depending on the qdisc in use. NFP currently
supports egress offload for TC flower offload so the changes are only
added to TC.
Fixes:
4d12ba42787b ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Thu, 5 Dec 2019 17:03:34 +0000 (17:03 +0000)]
net: core: rename indirect block ingress cb function
With indirect blocks, a driver can register for callbacks from a device
that is does not 'own', for example, a tunnel device. When registering to
or unregistering from a new device, a callback is triggered to generate
a bind/unbind event. This, in turn, allows the driver to receive any
existing rules or to properly clean up installed rules.
When first added, it was assumed that all indirect block registrations
would be for ingress offloads. However, the NFP driver can, in some
instances, support clsact qdisc binds for egress offload.
Change the name of the indirect block callback command in flow_offload to
remove the 'ingress' identifier from it. While this does not change
functionality, a follow up patch will implement a more more generic
callback than just those currently just supporting ingress offload.
Fixes:
4d12ba42787b ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jouni Hogander [Thu, 5 Dec 2019 13:57:07 +0000 (15:57 +0200)]
net-sysfs: Call dev_hold always in netdev_queue_add_kobject
Dev_hold has to be called always in netdev_queue_add_kobject.
Otherwise usage count drops below 0 in case of failure in
kobject_init_and_add.
Fixes:
b8eb718348b8 ("net-sysfs: Fix reference count leak in rx|netdev_queue_add_kobject")
Reported-by: Hulk Robot <hulkci@huawei.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: David Miller <davem@davemloft.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Lobakin [Thu, 5 Dec 2019 10:02:35 +0000 (13:02 +0300)]
net: dsa: fix flow dissection on Tx path
Commit
43e665287f93 ("net-next: dsa: fix flow dissection") added an
ability to override protocol and network offset during flow dissection
for DSA-enabled devices (i.e. controllers shipped as switch CPU ports)
in order to fix skb hashing for RPS on Rx path.
However, skb_hash() and added part of code can be invoked not only on
Rx, but also on Tx path if we have a multi-queued device and:
- kernel is running on UP system or
- XPS is not configured.
The call stack in this two cases will be like: dev_queue_xmit() ->
__dev_queue_xmit() -> netdev_core_pick_tx() -> netdev_pick_tx() ->
skb_tx_hash() -> skb_get_hash().
The problem is that skbs queued for Tx have both network offset and
correct protocol already set up even after inserting a CPU tag by DSA
tagger, so calling tag_ops->flow_dissect() on this path actually only
breaks flow dissection and hashing.
This can be observed by adding debug prints just before and right after
tag_ops->flow_dissect() call to the related block of code:
Before the patch:
Rx path (RPS):
[ 19.240001] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[ 19.244271] tag_ops->flow_dissect()
[ 19.247811] Rx: proto: 0x0800, nhoff: 8 /* ETH_P_IP */
[ 19.215435] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[ 19.219746] tag_ops->flow_dissect()
[ 19.223241] Rx: proto: 0x0806, nhoff: 8 /* ETH_P_ARP */
[ 18.654057] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[ 18.658332] tag_ops->flow_dissect()
[ 18.661826] Rx: proto: 0x8100, nhoff: 8 /* ETH_P_8021Q */
Tx path (UP system):
[ 18.759560] Tx: proto: 0x0800, nhoff: 26 /* ETH_P_IP */
[ 18.763933] tag_ops->flow_dissect()
[ 18.767485] Tx: proto: 0x920b, nhoff: 34 /* junk */
[ 22.800020] Tx: proto: 0x0806, nhoff: 26 /* ETH_P_ARP */
[ 22.804392] tag_ops->flow_dissect()
[ 22.807921] Tx: proto: 0x920b, nhoff: 34 /* junk */
[ 16.898342] Tx: proto: 0x86dd, nhoff: 26 /* ETH_P_IPV6 */
[ 16.902705] tag_ops->flow_dissect()
[ 16.906227] Tx: proto: 0x920b, nhoff: 34 /* junk */
After:
Rx path (RPS):
[ 16.520993] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[ 16.525260] tag_ops->flow_dissect()
[ 16.528808] Rx: proto: 0x0800, nhoff: 8 /* ETH_P_IP */
[ 15.484807] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[ 15.490417] tag_ops->flow_dissect()
[ 15.495223] Rx: proto: 0x0806, nhoff: 8 /* ETH_P_ARP */
[ 17.134621] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[ 17.138895] tag_ops->flow_dissect()
[ 17.142388] Rx: proto: 0x8100, nhoff: 8 /* ETH_P_8021Q */
Tx path (UP system):
[ 15.499558] Tx: proto: 0x0800, nhoff: 26 /* ETH_P_IP */
[ 20.664689] Tx: proto: 0x0806, nhoff: 26 /* ETH_P_ARP */
[ 18.565782] Tx: proto: 0x86dd, nhoff: 26 /* ETH_P_IPV6 */
In order to fix that we can add the check 'proto == htons(ETH_P_XDSA)'
to prevent code from calling tag_ops->flow_dissect() on Tx.
I also decided to initialize 'offset' variable so tagger callbacks can
now safely leave it untouched without provoking a chaos.
Fixes:
43e665287f93 ("net-next: dsa: fix flow dissection")
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Valentin Vidic [Thu, 5 Dec 2019 06:41:18 +0000 (07:41 +0100)]
net/tls: Fix return values to avoid ENOTSUPP
ENOTSUPP is not available in userspace, for example:
setsockopt failed, 524, Unknown error 524
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 6 Dec 2019 17:38:36 +0000 (09:38 -0800)]
net: avoid an indirect call in ____sys_recvmsg()
CONFIG_RETPOLINE=y made indirect calls expensive.
gcc seems to add an indirect call in ____sys_recvmsg().
Rewriting the code slightly makes sure to avoid this indirection.
Alternative would be to not call sock_recvmsg() and instead
use security_socket_recvmsg() and sock_recvmsg_nosec(),
but this is less readable IMO.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: David Laight <David.Laight@aculab.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chuhong Yuan [Fri, 6 Dec 2019 07:54:46 +0000 (15:54 +0800)]
phy: mdio-thunder: add missed pci_release_regions in remove
The driver forgets to call pci_release_regions() in remove like that
in probe failure.
Add the missed call to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Fri, 6 Dec 2019 05:25:48 +0000 (05:25 +0000)]
tipc: fix ordering of tipc module init and exit routine
In order to set/get/dump, the tipc uses the generic netlink
infrastructure. So, when tipc module is inserted, init function
calls genl_register_family().
After genl_register_family(), set/get/dump commands are immediately
allowed and these callbacks internally use the net_generic.
net_generic is allocated by register_pernet_device() but this
is called after genl_register_family() in the __init function.
So, these callbacks would use un-initialized net_generic.
Test commands:
#SHELL1
while :
do
modprobe tipc
modprobe -rv tipc
done
#SHELL2
while :
do
tipc link list
done
Splat looks like:
[ 59.616322][ T2788] kasan: CONFIG_KASAN_INLINE enabled
[ 59.617234][ T2788] kasan: GPF could be caused by NULL-ptr deref or user memory access
[ 59.618398][ T2788] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 59.619389][ T2788] CPU: 3 PID: 2788 Comm: tipc Not tainted 5.4.0+ #194
[ 59.620231][ T2788] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 59.621428][ T2788] RIP: 0010:tipc_bcast_get_broadcast_mode+0x131/0x310 [tipc]
[ 59.622379][ T2788] Code: c7 c6 ef 8b 38 c0 65 ff 0d 84 83 c9 3f e8 d7 a5 f2 e3 48 8d bb 38 11 00 00 48 b8 00 00 00 00
[ 59.622550][ T2780] NET: Registered protocol family 30
[ 59.624627][ T2788] RSP: 0018:
ffff88804b09f578 EFLAGS:
00010202
[ 59.624630][ T2788] RAX:
dffffc0000000000 RBX:
0000000000000011 RCX:
000000008bc66907
[ 59.624631][ T2788] RDX:
0000000000000229 RSI:
000000004b3cf4cc RDI:
0000000000001149
[ 59.624633][ T2788] RBP:
ffff88804b09f588 R08:
0000000000000003 R09:
fffffbfff4fb3df1
[ 59.624635][ T2788] R10:
fffffbfff50318f8 R11:
ffff888066cadc18 R12:
ffffffffa6cc2f40
[ 59.624637][ T2788] R13:
1ffff11009613eba R14:
ffff8880662e9328 R15:
ffff8880662e9328
[ 59.624639][ T2788] FS:
00007f57d8f7b740(0000) GS:
ffff88806cc00000(0000) knlGS:
0000000000000000
[ 59.624645][ T2788] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 59.625875][ T2780] tipc: Started in single node mode
[ 59.626128][ T2788] CR2:
00007f57d887a8c0 CR3:
000000004b140002 CR4:
00000000000606e0
[ 59.633991][ T2788] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[ 59.635195][ T2788] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[ 59.636478][ T2788] Call Trace:
[ 59.637025][ T2788] tipc_nl_add_bc_link+0x179/0x1470 [tipc]
[ 59.638219][ T2788] ? lock_downgrade+0x6e0/0x6e0
[ 59.638923][ T2788] ? __tipc_nl_add_link+0xf90/0xf90 [tipc]
[ 59.639533][ T2788] ? tipc_nl_node_dump_link+0x318/0xa50 [tipc]
[ 59.640160][ T2788] ? mutex_lock_io_nested+0x1380/0x1380
[ 59.640746][ T2788] tipc_nl_node_dump_link+0x4fd/0xa50 [tipc]
[ 59.641356][ T2788] ? tipc_nl_node_reset_link_stats+0x340/0x340 [tipc]
[ 59.642088][ T2788] ? __skb_ext_del+0x270/0x270
[ 59.642594][ T2788] genl_lock_dumpit+0x85/0xb0
[ 59.643050][ T2788] netlink_dump+0x49c/0xed0
[ 59.643529][ T2788] ? __netlink_sendskb+0xc0/0xc0
[ 59.644044][ T2788] ? __netlink_dump_start+0x190/0x800
[ 59.644617][ T2788] ? __mutex_unlock_slowpath+0xd0/0x670
[ 59.645177][ T2788] __netlink_dump_start+0x5a0/0x800
[ 59.645692][ T2788] genl_rcv_msg+0xa75/0xe90
[ 59.646144][ T2788] ? __lock_acquire+0xdfe/0x3de0
[ 59.646692][ T2788] ? genl_family_rcv_msg_attrs_parse+0x320/0x320
[ 59.647340][ T2788] ? genl_lock_dumpit+0xb0/0xb0
[ 59.647821][ T2788] ? genl_unlock+0x20/0x20
[ 59.648290][ T2788] ? genl_parallel_done+0xe0/0xe0
[ 59.648787][ T2788] ? find_held_lock+0x39/0x1d0
[ 59.649276][ T2788] ? genl_rcv+0x15/0x40
[ 59.649722][ T2788] ? lock_contended+0xcd0/0xcd0
[ 59.650296][ T2788] netlink_rcv_skb+0x121/0x350
[ 59.650828][ T2788] ? genl_family_rcv_msg_attrs_parse+0x320/0x320
[ 59.651491][ T2788] ? netlink_ack+0x940/0x940
[ 59.651953][ T2788] ? lock_acquire+0x164/0x3b0
[ 59.652449][ T2788] genl_rcv+0x24/0x40
[ 59.652841][ T2788] netlink_unicast+0x421/0x600
[ ... ]
Fixes:
7e4369057806 ("tipc: fix a slab object leak")
Fixes:
a62fbccecd62 ("tipc: make subscriber server support net namespace")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladyslav Tarasiuk [Fri, 6 Dec 2019 13:51:05 +0000 (13:51 +0000)]
mqprio: Fix out-of-bounds access in mqprio_dump
When user runs a command like
tc qdisc add dev eth1 root mqprio
KASAN stack-out-of-bounds warning is emitted.
Currently, NLA_ALIGN macro used in mqprio_dump provides too large
buffer size as argument for nla_put and memcpy down the call stack.
The flow looks like this:
1. nla_put expects exact object size as an argument;
2. Later it provides this size to memcpy;
3. To calculate correct padding for SKB, nla_put applies NLA_ALIGN
macro itself.
Therefore, NLA_ALIGN should not be applied to the nla_put parameter.
Otherwise it will lead to out-of-bounds memory access in memcpy.
Fixes:
4e8b86c06269 ("mqprio: Introduce new hardware offload mode and shaper in mqprio")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jongsung Kim [Fri, 6 Dec 2019 11:40:00 +0000 (20:40 +0900)]
net: stmmac: reset Tx desc base address before restarting Tx
Refer to the databook of DesignWare Cores Ethernet MAC Universal:
6.2.1.5 Register 4 (Transmit Descriptor List Address Register
If this register is not changed when the ST bit is set to 0, then
the DMA takes the descriptor address where it was stopped earlier.
The stmmac_tx_err() does zero indices to Tx descriptors, but does
not reset HW current Tx descriptor address. To fix inconsistency,
the base address of the Tx descriptors should be rewritten before
restarting Tx.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yangbo Lu [Fri, 6 Dec 2019 09:53:35 +0000 (17:53 +0800)]
enetc: disable EEE autoneg by default
The EEE support has not been enabled on ENETC, but it may connect
to a PHY which supports EEE and advertises EEE by default, while
its link partner also advertises EEE. If this happens, the PHY enters
low power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
ENETC connects to, to prevent the above unwanted outcome.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 6 Dec 2019 08:04:15 +0000 (00:04 -0800)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Alexei Starovoitov says:
====================
pull-request: bpf 2019-12-05
The following pull-request contains BPF updates for your *net* tree.
We've added 6 non-merge commits during the last 1 day(s) which contain
a total of 14 files changed, 116 insertions(+), 37 deletions(-).
The main changes are:
1) three selftests fixes, from Stanislav.
2) one samples fix, from Jesper.
3) one verifier fix, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Biggers [Thu, 5 Dec 2019 05:54:19 +0000 (21:54 -0800)]
ppp: fix out-of-bounds access in bpf_prog_create()
sock_fprog_kern::len is in units of struct sock_filter, not bytes.
Fixes:
3e859adf3643 ("compat_ioctl: unify copy-in of ppp filters")
Reported-by: syzbot+eb853b51b10f1befa0b7@syzkaller.appspotmail.com
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 5 Dec 2019 22:42:43 +0000 (14:42 -0800)]
Merge branch 'hns3-fixes'
Huazhong Tan says:
====================
net: hns3: fixes for -net
This patchset includes misc fixes for the HNS3 ethernet driver.
[patch 1/3] fixes a TX queue not restarted problem.
[patch 2/3] fixes a use-after-free issue.
[patch 3/3] fixes a VF ID issue for setting VF VLAN.
change log:
V1->V2: keeps 'ring' as parameter in hns3_nic_maybe_stop_tx()
in [patch 1/3], suggestted by David.
rewrites [patch 2/3]'s commit log to make it be easier
to understand, suggestted by David.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Thu, 5 Dec 2019 02:12:29 +0000 (10:12 +0800)]
net: hns3: fix VF ID issue for setting VF VLAN
Previously, when set VF VLAN with command "ip link set <pf name>
vf <vf id> vlan <vlan id>", the VF ID 0 is handled as PF incorrectly,
which should be the first VF. This patch fixes it.
Fixes:
21e043cd8124 ("net: hns3: fix set port based VLAN for PF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Thu, 5 Dec 2019 02:12:28 +0000 (10:12 +0800)]
net: hns3: fix a use after free problem in hns3_nic_maybe_stop_tx()
Currently, hns3_nic_maybe_stop_tx() uses skb_copy() to linearize a
SKB if the BD num required by the SKB does not meet the hardware
limitation, and it linearizes the SKB by allocating a new linearized SKB
and freeing the old SKB, if hns3_nic_maybe_stop_tx() returns -EBUSY
because there are no enough space in the ring to send the linearized
skb to hardware, the sch_direct_xmit() still hold reference to old SKB
and try to retransmit the old SKB when dev_hard_start_xmit() return
TX_BUSY, which may cause use after freed problem.
This patch fixes it by using __skb_linearize() to linearize the
SKB in hns3_nic_maybe_stop_tx().
Fixes:
51e8439f3496 ("net: hns3: add 8 BD limit for tx flow")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Thu, 5 Dec 2019 02:12:27 +0000 (10:12 +0800)]
net: hns3: fix for TX queue not restarted problem
There is timing window between ring_space checking and
netif_stop_subqueue when transmiting a SKB, and the TX BD
cleaning may be executed during the time window, which may
caused TX queue not restarted problem.
This patch fixes it by rechecking the ring_space after
netif_stop_subqueue to make sure TX queue is restarted.
Also, the ring->next_to_clean is updated even when pkts is
zero, because all the TX BD cleaned may be non-SKB, so it
needs to check if TX queue need to be restarted.
Fixes:
76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Wed, 4 Dec 2019 17:45:32 +0000 (19:45 +0200)]
net: ethernet: ti: cpsw_switchdev: fix unmet direct dependencies detected for NET_SWITCHDEV
Replace "select NET_SWITCHDEV" vs "depends on NET_SWITCHDEV" to fix Kconfig
warning with CONFIG_COMPILE_TEST=y
WARNING: unmet direct dependencies detected for NET_SWITCHDEV
Depends on [n]: NET [=y] && INET [=n]
Selected by [y]:
- TI_CPSW_SWITCHDEV [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && (ARCH_DAVINCI || ARCH_OMAP2PLUS || COMPILE_TEST [=y])
because TI_CPSW_SWITCHDEV blindly selects NET_SWITCHDEV even though
INET is not set/enabled, while NET_SWITCHDEV depends on INET.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes:
ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
Parav Pandit [Tue, 12 Nov 2019 23:06:00 +0000 (17:06 -0600)]
net/mlx5e: E-switch, Fix Ingress ACL groups in switchdev mode for prio tag
In cited commit, when prio tag mode is enabled, FTE creation fails
due to missing group with valid match criteria.
Hence,
(a) create prio tag group metadata_prio_tag_grp when prio tag is
enabled with match criteria for vlan push FTE.
(b) Rename metadata_grp to metadata_allmatch_grp to reflect its purpose.
Also when priority tag is enabled, delete metadata settings after
deleting ingress rules, which are using it.
Tide up rest of the ingress config code for unnecessary labels.
Fixes:
10652f39943e ("net/mlx5: Refactor ingress acl configuration")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Aya Levin [Sun, 1 Dec 2019 14:33:55 +0000 (16:33 +0200)]
net/mlx5e: ethtool, Fix analysis of speed setting
When setting speed to 100G via ethtool (AN is set to off), only 25G*4 is
configured while the user, who has an advanced HW which supports
extended PTYS, expects also 50G*2 to be configured.
With this patch, when extended PTYS mode is available, configure
PTYS via extended fields.
Fixes:
4b95840a6ced ("net/mlx5e: Fix matching of speed to PRM link modes")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Aya Levin [Sun, 1 Dec 2019 12:45:25 +0000 (14:45 +0200)]
net/mlx5e: Fix translation of link mode into speed
Add a missing value in translation of PTYS ext_eth_proto_oper to its
corresponding speed. When ext_eth_proto_oper bit 10 is set, ethtool
shows unknown speed. With this fix, ethtool shows speed is 100G as
expected.
Fixes:
a08b4ed1373d ("net/mlx5: Add support to ext_* fields introduced in Port Type and Speed register")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Roi Dayan [Mon, 2 Dec 2019 17:19:47 +0000 (19:19 +0200)]
net/mlx5e: Fix free peer_flow when refcount is 0
It could be neigh update flow took a refcount on peer flow so
sometimes we cannot release peer flow even if parent flow is
being freed now.
Fixes:
5a7e5bcb663d ("net/mlx5e: Extend tc flow struct with reference counter")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Roi Dayan [Wed, 4 Dec 2019 09:25:43 +0000 (11:25 +0200)]
net/mlx5e: Fix freeing flow with kfree() and not kvfree()
Flows are allocated with kzalloc() so free with kfree().
Fixes:
04de7dda7394 ("net/mlx5e: Infrastructure for duplicated offloading of TC flows")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eran Ben Elisha [Thu, 5 Dec 2019 08:30:22 +0000 (10:30 +0200)]
net/mlx5e: Fix SFF 8472 eeprom length
SFF 8472 eeprom length is 512 bytes. Fix module info return value to
support 512 bytes read.
Fixes:
ace329f4ab3b ("net/mlx5e: ethtool, Remove unsupported SFP EEPROM high pages query")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Huy Nguyen [Fri, 6 Sep 2019 14:28:46 +0000 (09:28 -0500)]
net/mlx5e: Query global pause state before setting prio2buffer
When the user changes prio2buffer mapping while global pause is
enabled, mlx5 driver incorrectly sets all active buffers
(buffer that has at least one priority mapped) to lossy.
Solution:
If global pause is enabled, set all the active buffers to lossless
in prio2buffer command.
Also, add error message when buffer size is not enough to meet
xoff threshold.
Fixes:
0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eran Ben Elisha [Mon, 25 Nov 2019 10:11:49 +0000 (12:11 +0200)]
net/mlx5e: Fix TXQ indices to be sequential
Cited patch changed (channel index, tc) => (TXQ index) mapping to be a
static one, in order to keep indices consistent when changing number of
channels or TCs.
For 32 channels (OOB) and 8 TCs, real num of TXQs is 256.
When reducing the amount of channels to 8, the real num of TXQs will be
changed to 64.
This indices method is buggy:
- Channel #0, TC 3, the TXQ index is 96.
- Index 8 is not valid, as there is no such TXQ from driver perspective
(As it represents channel #8, TC 0, which is not valid with the above
configuration).
As part of driver's select queue, it calls netdev_pick_tx which returns an
index in the range of real number of TXQs. Depends on the return value,
with the examples above, driver could have returned index larger than the
real number of tx queues, or crash the kernel as it tries to read invalid
address of SQ which was not allocated.
Fix that by allocating sequential TXQ indices, and hold a new mapping
between (channel index, tc) => (real TXQ index). This mapping will be
updated as part of priv channels activation, and is used in
mlx5e_select_queue to find the selected queue index.
The existing indices mapping (channel_tc2txq) is no longer needed, as it
is used only for statistics structures and can be calculated on run time.
Delete its definintion and updates.
Fixes:
8bfaf07f7806 ("net/mlx5e: Present SW stats when state is not opened")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
David S. Miller [Thu, 5 Dec 2019 20:25:05 +0000 (12:25 -0800)]
Merge branch 's390-fixes'
Julian Wiedmann says:
====================
s390/qeth: fixes 2019-12-05
please apply the following fixes to your net tree.
The first two patches target the RX data path, the third fixes a memory
leak when shutting down a qeth device.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 5 Dec 2019 13:33:04 +0000 (14:33 +0100)]
s390/qeth: fix dangling IO buffers after halt/clear
The cio layer's intparm logic does not align itself well with how qeth
manages cmd IOs. When an active IO gets terminated via halt/clear, the
corresponding IRQ's intparm does not reflect the cmd buffer but rather
the intparm that was passed to ccw_device_halt() / ccw_device_clear().
This behaviour was recently clarified in
commit
b91d9e67e50b ("s390/cio: fix intparm documentation").
As a result, qeth_irq() currently doesn't cancel a cmd that was
terminated via halt/clear. This primarily causes us to leak
card->read_cmd after the qeth device is removed, since our IO path still
holds a refcount for this cmd.
For qeth this means that we need to keep track of which IO is pending on
a device ('active_cmd'), and use this as the intparm when calling
halt/clear. Otherwise qeth_irq() can't match the subsequent IRQ to its
cmd buffer.
Since we now keep track of the _expected_ intparm, we can also detect
any mismatch; this would constitute a bug somewhere in the lower layers.
In this case cancel the active cmd - we effectively "lost" the IRQ and
should not expect any further notification for this IO.
Fixes:
405548959cc7 ("s390/qeth: add support for dynamically allocated cmds")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 5 Dec 2019 13:33:03 +0000 (14:33 +0100)]
s390/qeth: ensure linear access to packet headers
When the RX path builds non-linear skbs, the packet headers can
currently spill over into page fragments. Depending on the packet type
and what fields we need to access in the headers, this could cause us
to go past the end of skb->data.
So for non-linear packets, copy precisely the length of the necessary
headers ('linear_len') into skb->data.
And don't copy more, upper-level protocols will peel whatever additional
packet headers they need.
Fixes:
4a71df50047f ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 5 Dec 2019 13:33:02 +0000 (14:33 +0100)]
s390/qeth: guard against runt packets
Depending on a packet's type, the RX path needs to access fields in the
packet headers and thus requires a minimum packet length.
Enforce this length when building the skb.
On the other hand a single runt packet is no reason to drop the whole
RX buffer. So just skip it, and continue processing on the next packet.
Fixes:
4a71df50047f ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mian Yousaf Kaukab [Thu, 5 Dec 2019 09:41:16 +0000 (10:41 +0100)]
net: thunderx: start phy before starting autonegotiation
Since commit
2b3e88ea6528 ("net: phy: improve phy state checking")
phy_start_aneg() expects phy state to be >= PHY_UP. Call phy_start()
before calling phy_start_aneg() during probe so that autonegotiation
is initiated.
As phy_start() takes care of calling phy_start_aneg(), drop the explicit
call to phy_start_aneg().
Network fails without this patch on Octeon TX.
Fixes:
2b3e88ea6528 ("net: phy: improve phy state checking")
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Thu, 5 Dec 2019 07:23:39 +0000 (07:23 +0000)]
hsr: fix a NULL pointer dereference in hsr_dev_xmit()
hsr_dev_xmit() calls hsr_port_get_hsr() to find master node and that would
return NULL if master node is not existing in the list.
But hsr_dev_xmit() doesn't check return pointer so a NULL dereference
could occur.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
hping3 192.168.100.2 -2 --flood &
modprobe -rv hsr
Splat looks like:
[ 217.351122][ T1635] kasan: CONFIG_KASAN_INLINE enabled
[ 217.352969][ T1635] kasan: GPF could be caused by NULL-ptr deref or user memory access
[ 217.354297][ T1635] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 217.355507][ T1635] CPU: 1 PID: 1635 Comm: hping3 Not tainted 5.4.0+ #192
[ 217.356472][ T1635] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 217.357804][ T1635] RIP: 0010:hsr_dev_xmit+0x34/0x90 [hsr]
[ 217.373010][ T1635] Code: 48 8d be 00 0c 00 00 be 04 00 00 00 48 83 ec 08 e8 21 be ff ff 48 8d 78 10 48 ba 00 b
[ 217.376919][ T1635] RSP: 0018:
ffff8880cd8af058 EFLAGS:
00010202
[ 217.377571][ T1635] RAX:
0000000000000000 RBX:
ffff8880acde6840 RCX:
0000000000000002
[ 217.379465][ T1635] RDX:
dffffc0000000000 RSI:
0000000000000004 RDI:
0000000000000010
[ 217.380274][ T1635] RBP:
ffff8880acde6840 R08:
ffffed101b440d5d R09:
0000000000000001
[ 217.381078][ T1635] R10:
0000000000000001 R11:
ffffed101b440d5c R12:
ffff8880bffcc000
[ 217.382023][ T1635] R13:
ffff8880bffcc088 R14:
0000000000000000 R15:
ffff8880ca675c00
[ 217.383094][ T1635] FS:
00007f060d9d1740(0000) GS:
ffff8880da000000(0000) knlGS:
0000000000000000
[ 217.384289][ T1635] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 217.385009][ T1635] CR2:
00007faf15381dd0 CR3:
00000000d523c001 CR4:
00000000000606e0
[ 217.385940][ T1635] Call Trace:
[ 217.386544][ T1635] dev_hard_start_xmit+0x160/0x740
[ 217.387114][ T1635] __dev_queue_xmit+0x1961/0x2e10
[ 217.388118][ T1635] ? check_object+0xaf/0x260
[ 217.391466][ T1635] ? __alloc_skb+0xb9/0x500
[ 217.392017][ T1635] ? init_object+0x6b/0x80
[ 217.392629][ T1635] ? netdev_core_pick_tx+0x2e0/0x2e0
[ 217.393175][ T1635] ? __alloc_skb+0xb9/0x500
[ 217.393727][ T1635] ? rcu_read_lock_sched_held+0x90/0xc0
[ 217.394331][ T1635] ? rcu_read_lock_bh_held+0xa0/0xa0
[ 217.395013][ T1635] ? kasan_unpoison_shadow+0x30/0x40
[ 217.395668][ T1635] ? __kasan_kmalloc.constprop.4+0xa0/0xd0
[ 217.396280][ T1635] ? __kmalloc_node_track_caller+0x3a8/0x3f0
[ 217.399007][ T1635] ? __kasan_kmalloc.constprop.4+0xa0/0xd0
[ 217.400093][ T1635] ? __kmalloc_reserve.isra.46+0x2e/0xb0
[ 217.401118][ T1635] ? memset+0x1f/0x40
[ 217.402529][ T1635] ? __alloc_skb+0x317/0x500
[ 217.404915][ T1635] ? arp_xmit+0xca/0x2c0
[ ... ]
Fixes:
311633b60406 ("hsr: switch ->dellink() to ->ndo_uninit()")
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song [Thu, 5 Dec 2019 01:06:07 +0000 (17:06 -0800)]
selftests/bpf: Add a fexit/bpf2bpf test with target bpf prog no callees
The existing fexit_bpf2bpf test covers the target progrm with callees.
This patch added a test for the target program without callees.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191205010607.177904-1-yhs@fb.com
Yonghong Song [Thu, 5 Dec 2019 01:06:06 +0000 (17:06 -0800)]
bpf: Fix a bug when getting subprog 0 jited image in check_attach_btf_id
For jited bpf program, if the subprogram count is 1, i.e.,
there is no callees in the program, prog->aux->func will be NULL
and prog->bpf_func points to image address of the program.
If there is more than one subprogram, prog->aux->func is populated,
and subprogram 0 can be accessed through either prog->bpf_func or
prog->aux->func[0]. Other subprograms should be accessed through
prog->aux->func[subprog_id].
This patch fixed a bug in check_attach_btf_id(), where
prog->aux->func[subprog_id] is used to access any subprogram which
caused a segfault like below:
[79162.619208] BUG: kernel NULL pointer dereference, address:
0000000000000000
......
[79162.634255] Call Trace:
[79162.634974] ? _cond_resched+0x15/0x30
[79162.635686] ? kmem_cache_alloc_trace+0x162/0x220
[79162.636398] ? selinux_bpf_prog_alloc+0x1f/0x60
[79162.637111] bpf_prog_load+0x3de/0x690
[79162.637809] __do_sys_bpf+0x105/0x1740
[79162.638488] do_syscall_64+0x5b/0x180
[79162.639147] entry_SYSCALL_64_after_hwframe+0x44/0xa9
......
Fixes:
5b92a28aae4d ("bpf: Support attaching tracing BPF program to other BPF programs")
Reported-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191205010606.177774-1-yhs@fb.com
Stanislav Fomichev [Wed, 4 Dec 2019 19:09:55 +0000 (11:09 -0800)]
selftests/bpf: De-flake test_tcpbpf
It looks like BPF program that handles BPF_SOCK_OPS_STATE_CB state
can race with the bpf_map_lookup_elem("global_map"); I sometimes
see the failures in this test and re-running helps.
Since we know that we expect the callback to be called 3 times (one
time for listener socket, two times for both ends of the connection),
let's export this number and add simple retry logic around that.
Also, let's make EXPECT_EQ() not return on failure, but continue
evaluating all conditions; that should make potential debugging
easier.
With this fix in place I don't observe the flakiness anymore.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Lawrence Brakmo <brakmo@fb.com>
Link: https://lore.kernel.org/bpf/20191204190955.170934-1-sdf@google.com
Stanislav Fomichev [Mon, 2 Dec 2019 21:59:31 +0000 (13:59 -0800)]
selftests/bpf: Bring back c++ include/link test
Commit
5c26f9a78358 ("libbpf: Don't use cxx to test_libpf target")
converted existing c++ test to c. We still want to include and
link against libbpf from c++ code, so reinstate this test back,
this time in a form of a selftest with a clear comment about
its purpose.
v2:
* -lelf -> $(LDLIBS) (Andrii Nakryiko)
Fixes:
5c26f9a78358 ("libbpf: Don't use cxx to test_libpf target")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191202215931.248178-1-sdf@google.com
Stanislav Fomichev [Mon, 2 Dec 2019 20:01:43 +0000 (12:01 -0800)]
selftests/bpf: Don't hard-code root cgroup id
Commit
40430452fd5d ("kernfs: use 64bit inos if ino_t is 64bit") changed
the way cgroup ids are exposed to the userspace. Instead of assuming
fixed root id, let's query it.
Fixes:
40430452fd5d ("kernfs: use 64bit inos if ino_t is 64bit")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191202200143.250793-1-sdf@google.com
Jesper Dangaard Brouer [Mon, 2 Dec 2019 12:37:31 +0000 (13:37 +0100)]
samples/bpf: Fix broken xdp_rxq_info due to map order assumptions
In the days of using bpf_load.c the order in which the 'maps' sections
were defines in BPF side (*_kern.c) file, were used by userspace side
to identify the map via using the map order as an index. In effect the
order-index is created based on the order the maps sections are stored
in the ELF-object file, by the LLVM compiler.
This have also carried over in libbpf via API bpf_map__next(NULL, obj)
to extract maps in the order libbpf parsed the ELF-object file.
When BTF based maps were introduced a new section type ".maps" were
created. I found that the LLVM compiler doesn't create the ".maps"
sections in the order they are defined in the C-file. The order in the
ELF file is based on the order the map pointer is referenced in the code.
This combination of changes lead to xdp_rxq_info mixing up the map
file-descriptors in userspace, resulting in very broken behaviour, but
without warning the user.
This patch fix issue by instead using bpf_object__find_map_by_name()
to find maps via their names. (Note, this is the ELF name, which can
be longer than the name the kernel retains).
Fixes:
be5bca44aa6b ("samples: bpf: convert some XDP samples from bpf_load to libbpf")
Fixes:
451d1dc886b5 ("samples: bpf: update map definition to new syntax BTF-defined map")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/157529025128.29832.5953245340679936909.stgit@firesoul
Martin Varghese [Thu, 5 Dec 2019 00:27:22 +0000 (05:57 +0530)]
net: Fixed updating of ethertype in skb_mpls_push()
The skb_mpls_push was not updating ethertype of an ethernet packet if
the packet was originally received from a non ARPHRD_ETHER device.
In the below OVS data path flow, since the device corresponding to
port 7 is an l3 device (ARPHRD_NONE) the skb_mpls_push function does
not update the ethertype of the packet even though the previous
push_eth action had added an ethernet header to the packet.
recirc_id(0),in_port(7),eth_type(0x0800),ipv4(tos=0/0xfc,ttl=64,frag=no),
actions:push_eth(src=00:00:00:00:00:00,dst=00:00:00:00:00:00),
push_mpls(label=13,tc=0,ttl=64,bos=1,eth_type=0x8847),4
Fixes:
8822e270d697 ("net: core: move push MPLS functionality from OvS to core helper")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandru Ardelean [Wed, 4 Dec 2019 07:58:09 +0000 (09:58 +0200)]
NFC: NCI: use new `delay` structure for SPI transfer delays
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current `delay_secs`
with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit
bebcfd272df6485 ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 3 Dec 2019 23:51:28 +0000 (23:51 +0000)]
net: sfp: fix hwmon
The referenced commit below allowed more than one hwmon device to be
created per SFP, which is definitely not what we want. Avoid this by
only creating the hwmon device just as we transition to WAITDEV state.
Fixes:
139d3a212a1f ("net: sfp: allow modules with slow diagnostics to probe")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 3 Dec 2019 23:51:22 +0000 (23:51 +0000)]
net: sfp: fix unbind
When unbinding, we don't correctly tear down the module state, leaving
(for example) the hwmon registration behind. Ensure everything is
properly removed by sending a remove event at unbind.
Fixes:
6b0da5c9c1a3 ("net: sfp: track upstream's attachment state in state machine")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Tue, 3 Dec 2019 22:17:34 +0000 (14:17 -0800)]
ionic: keep users rss hash across lif reset
If the user has specified their own RSS hash key, don't
lose it across queue resets such as DOWN/UP, MTU change,
and number of channels change. This is fixed by moving
the key initialization to a little earlier in the lif
creation.
Also, let's clean up the RSS config a little better on
the way down by setting it all to 0.
Fixes:
aa3198819bea ("ionic: Add RSS support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan Lemon [Tue, 3 Dec 2019 22:01:14 +0000 (14:01 -0800)]
xdp: obtain the mem_id mutex before trying to remove an entry.
A lockdep splat was observed when trying to remove an xdp memory
model from the table since the mutex was obtained when trying to
remove the entry, but not before the table walk started:
Fix the splat by obtaining the lock before starting the table walk.
Fixes:
c3f812cea0d7 ("page_pool: do not release pool until inflight == 0.")
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aaron Conole [Tue, 3 Dec 2019 21:34:14 +0000 (16:34 -0500)]
act_ct: support asymmetric conntrack
The act_ct TC module shares a common conntrack and NAT infrastructure
exposed via netfilter. It's possible that a packet needs both SNAT and
DNAT manipulation, due to e.g. tuple collision. Netfilter can support
this because it runs through the NAT table twice - once on ingress and
again after egress. The act_ct action doesn't have such capability.
Like netfilter hook infrastructure, we should run through NAT twice to
keep the symmetry.
Fixes:
b57dc7c13ea9 ("net/sched: Introduce action ct")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aaron Conole [Tue, 3 Dec 2019 21:34:13 +0000 (16:34 -0500)]
openvswitch: support asymmetric conntrack
The openvswitch module shares a common conntrack and NAT infrastructure
exposed via netfilter. It's possible that a packet needs both SNAT and
DNAT manipulation, due to e.g. tuple collision. Netfilter can support
this because it runs through the NAT table twice - once on ingress and
again after egress. The openvswitch module doesn't have such capability.
Like netfilter hook infrastructure, we should run through NAT twice to
keep the symmetry.
Fixes:
05752523e565 ("openvswitch: Interface with NAT.")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 4 Dec 2019 20:27:13 +0000 (12:27 -0800)]
Merge branch 'net-convert-ipv6_stub-to-ip6_dst_lookup_flow'
Sabrina Dubroca says:
====================
net: convert ipv6_stub to ip6_dst_lookup_flow
Xiumei Mu reported a bug in a VXLAN over IPsec setup:
IPv6 | ESP | VXLAN
Using this setup, packets go out unencrypted, because VXLAN over IPv6
gets its route from ipv6_stub->ipv6_dst_lookup (in vxlan6_get_route),
which doesn't perform an XFRM lookup.
This patchset first makes ip6_dst_lookup_flow suitable for some
existing users of ipv6_stub->ipv6_dst_lookup by adding a 'net'
argument, then converts all those users.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Wed, 4 Dec 2019 14:35:53 +0000 (15:35 +0100)]
net: ipv6_stub: use ip6_dst_lookup_flow instead of ip6_dst_lookup
ipv6_stub uses the ip6_dst_lookup function to allow other modules to
perform IPv6 lookups. However, this function skips the XFRM layer
entirely.
All users of ipv6_stub->ip6_dst_lookup use ip_route_output_flow (via the
ip_route_output_key and ip_route_output helpers) for their IPv4 lookups,
which calls xfrm_lookup_route(). This patch fixes this inconsistent
behavior by switching the stub to ip6_dst_lookup_flow, which also calls
xfrm_lookup_route().
This requires some changes in all the callers, as these two functions
take different arguments and have different return types.
Fixes:
5f81bd2e5d80 ("ipv6: export a stub for IPv6 symbols used by vxlan")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Wed, 4 Dec 2019 14:35:52 +0000 (15:35 +0100)]
net: ipv6: add net argument to ip6_dst_lookup_flow
This will be used in the conversion of ipv6_stub to ip6_dst_lookup_flow,
as some modules currently pass a net argument without a socket to
ip6_dst_lookup. This is equivalent to commit
343d60aada5a ("ipv6: change
ipv6_stub_impl.ipv6_dst_lookup to take net argument").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yoshiki Komachi [Tue, 3 Dec 2019 10:40:12 +0000 (19:40 +0900)]
cls_flower: Fix the behavior using port ranges with hw-offload
The recent commit
5c72299fba9d ("net: sched: cls_flower: Classify
packets using port ranges") had added filtering based on port ranges
to tc flower. However the commit missed necessary changes in hw-offload
code, so the feature gave rise to generating incorrect offloaded flow
keys in NIC.
One more detailed example is below:
$ tc qdisc add dev eth0 ingress
$ tc filter add dev eth0 ingress protocol ip flower ip_proto tcp \
dst_port 100-200 action drop
With the setup above, an exact match filter with dst_port == 0 will be
installed in NIC by hw-offload. IOW, the NIC will have a rule which is
equivalent to the following one.
$ tc qdisc add dev eth0 ingress
$ tc filter add dev eth0 ingress protocol ip flower ip_proto tcp \
dst_port 0 action drop
The behavior was caused by the flow dissector which extracts packet
data into the flow key in the tc flower. More specifically, regardless
of exact match or specified port ranges, fl_init_dissector() set the
FLOW_DISSECTOR_KEY_PORTS flag in struct flow_dissector to extract port
numbers from skb in skb_flow_dissect() called by fl_classify(). Note
that device drivers received the same struct flow_dissector object as
used in skb_flow_dissect(). Thus, offloaded drivers could not identify
which of these is used because the FLOW_DISSECTOR_KEY_PORTS flag was
set to struct flow_dissector in either case.
This patch adds the new FLOW_DISSECTOR_KEY_PORTS_RANGE flag and the new
tp_range field in struct fl_flow_key to recognize which filters are applied
to offloaded drivers. At this point, when filters based on port ranges
passed to drivers, drivers return the EOPNOTSUPP error because they do
not support the feature (the newly created FLOW_DISSECTOR_KEY_PORTS_RANGE
flag).
Fixes:
5c72299fba9d ("net: sched: cls_flower: Classify packets using port ranges")
Signed-off-by: Yoshiki Komachi <komachi.yoshiki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dust Li [Tue, 3 Dec 2019 03:17:40 +0000 (11:17 +0800)]
net: sched: fix dump qlen for sch_mq/sch_mqprio with NOLOCK subqueues
sch->q.len hasn't been set if the subqueue is a NOLOCK qdisc
in mq_dump() and mqprio_dump().
Fixes:
ce679e8df7ed ("net: sched: add support for TCQ_F_NOLOCK subqueues to sch_mqprio")
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 3 Dec 2019 16:05:52 +0000 (08:05 -0800)]
tcp: refactor tcp_retransmit_timer()
It appears linux-4.14 stable needs a backport of commit
88f8598d0a30 ("tcp: exit if nothing to retransmit on RTO timeout")
Since tcp_rtx_queue_empty() is not in pre 4.15 kernels,
let's refactor tcp_retransmit_timer() to only use tcp_rtx_queue_head()
I will provide to stable teams the squashed patches.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 3 Dec 2019 15:45:35 +0000 (17:45 +0200)]
net: mscc: ocelot: unregister the PTP clock on deinit
Currently a switch driver deinit frees the regmaps, but the PTP clock is
still out there, available to user space via /dev/ptpN. Any PTP
operation is a ticking time bomb, since it will attempt to use the freed
regmaps and thus trigger kernel panics:
[ 4.291746] fsl_enetc 0000:00:00.2 eth1: error -22 setting up slave phy
[ 4.291871] mscc_felix 0000:00:00.5: Failed to register DSA switch: -22
[ 4.308666] mscc_felix: probe of 0000:00:00.5 failed with error -22
[ 6.358270] Unable to handle kernel NULL pointer dereference at virtual address
0000000000000088
[ 6.367090] Mem abort info:
[ 6.369888] ESR = 0x96000046
[ 6.369891] EC = 0x25: DABT (current EL), IL = 32 bits
[ 6.369892] SET = 0, FnV = 0
[ 6.369894] EA = 0, S1PTW = 0
[ 6.369895] Data abort info:
[ 6.369897] ISV = 0, ISS = 0x00000046
[ 6.369899] CM = 0, WnR = 1
[ 6.369902] user pgtable: 4k pages, 48-bit VAs, pgdp=
00000020d58c7000
[ 6.369904] [
0000000000000088] pgd=
00000020d5912003, pud=
00000020d5915003, pmd=
0000000000000000
[ 6.369914] Internal error: Oops:
96000046 [#1] PREEMPT SMP
[ 6.420443] Modules linked in:
[ 6.423506] CPU: 1 PID: 262 Comm: phc_ctl Not tainted
5.4.0-03625-gb7b2a5dadd7f #204
[ 6.431273] Hardware name: LS1028A RDB Board (DT)
[ 6.435989] pstate:
40000085 (nZcv daIf -PAN -UAO)
[ 6.440802] pc : css_release+0x24/0x58
[ 6.444561] lr : regmap_read+0x40/0x78
[ 6.448316] sp :
ffff800010513cc0
[ 6.451636] x29:
ffff800010513cc0 x28:
ffff002055873040
[ 6.456963] x27:
0000000000000000 x26:
0000000000000000
[ 6.462289] x25:
0000000000000000 x24:
0000000000000000
[ 6.467617] x23:
0000000000000000 x22:
0000000000000080
[ 6.472944] x21:
ffff800010513d44 x20:
0000000000000080
[ 6.478270] x19:
0000000000000000 x18:
0000000000000000
[ 6.483596] x17:
0000000000000000 x16:
0000000000000000
[ 6.488921] x15:
0000000000000000 x14:
0000000000000000
[ 6.494247] x13:
0000000000000000 x12:
0000000000000000
[ 6.499573] x11:
0000000000000000 x10:
0000000000000000
[ 6.504899] x9 :
0000000000000000 x8 :
0000000000000000
[ 6.510225] x7 :
0000000000000000 x6 :
ffff800010513cf0
[ 6.515550] x5 :
0000000000000000 x4 :
0000000fffffffe0
[ 6.520876] x3 :
0000000000000088 x2 :
ffff800010513d44
[ 6.526202] x1 :
ffffcada668ea000 x0 :
ffffcada64d8b0c0
[ 6.531528] Call trace:
[ 6.533977] css_release+0x24/0x58
[ 6.537385] regmap_read+0x40/0x78
[ 6.540795] __ocelot_read_ix+0x6c/0xa0
[ 6.544641] ocelot_ptp_gettime64+0x4c/0x110
[ 6.548921] ptp_clock_gettime+0x4c/0x58
[ 6.552853] pc_clock_gettime+0x5c/0xa8
[ 6.556699] __arm64_sys_clock_gettime+0x68/0xc8
[ 6.561331] el0_svc_common.constprop.2+0x7c/0x178
[ 6.566133] el0_svc_handler+0x34/0xa0
[ 6.569891] el0_sync_handler+0x114/0x1d0
[ 6.573908] el0_sync+0x140/0x180
[ 6.577232] Code:
d503201f b00119a1 91022263 b27b7be4 (
f9004663)
[ 6.583349] ---[ end trace
d196b9b14cdae2da ]---
[ 6.587977] Kernel panic - not syncing: Fatal exception
[ 6.593216] SMP: stopping secondary CPUs
[ 6.597151] Kernel Offset: 0x4ada54400000 from 0xffff800010000000
[ 6.603261] PHYS_OFFSET: 0xffffd0a7c0000000
[ 6.607454] CPU features: 0x10002,
21806008
[ 6.611558] Memory Limit: none
And now that ocelot->ptp_clock is checked at exit, prevent a potential
error where ptp_clock_register returned a pointer-encoded error, which
we are keeping in the ocelot private data structure. So now,
ocelot->ptp_clock is now either NULL or a valid pointer.
Fixes:
4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Danit Goldberg [Tue, 3 Dec 2019 15:43:36 +0000 (17:43 +0200)]
net/core: Populate VF index in struct ifla_vf_guid
In addition to filling the node_guid and port_guid attributes,
there is a need to populate VF index too, otherwise users of netlink
interface will see same VF index for all VFs.
Fixes:
30aad41721e0 ("net/core: Add support for getting VF GUIDs")
Signed-off-by: Danit Goldberg <danitg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 3 Dec 2019 14:48:06 +0000 (16:48 +0200)]
net: bridge: deny dev_set_mac_address() when unregistering
We have an interesting memory leak in the bridge when it is being
unregistered and is a slave to a master device which would change the
mac of its slaves on unregister (e.g. bond, team). This is a very
unusual setup but we do end up leaking 1 fdb entry because
dev_set_mac_address() would cause the bridge to insert the new mac address
into its table after all fdbs are flushed, i.e. after dellink() on the
bridge has finished and we call NETDEV_UNREGISTER the bond/team would
release it and will call dev_set_mac_address() to restore its original
address and that in turn will add an fdb in the bridge.
One fix is to check for the bridge dev's reg_state in its
ndo_set_mac_address callback and return an error if the bridge is not in
NETREG_REGISTERED.
Easy steps to reproduce:
1. add bond in mode != A/B
2. add any slave to the bond
3. add bridge dev as a slave to the bond
4. destroy the bridge device
Trace:
unreferenced object 0xffff888035c4d080 (size 128):
comm "ip", pid 4068, jiffies
4296209429 (age 1413.753s)
hex dump (first 32 bytes):
41 1d c9 36 80 88 ff ff 00 00 00 00 00 00 00 00 A..6............
d2 19 c9 5e 3f d7 00 00 00 00 00 00 00 00 00 00 ...^?...........
backtrace:
[<
00000000ddb525dc>] kmem_cache_alloc+0x155/0x26f
[<
00000000633ff1e0>] fdb_create+0x21/0x486 [bridge]
[<
0000000092b17e9c>] fdb_insert+0x91/0xdc [bridge]
[<
00000000f2a0f0ff>] br_fdb_change_mac_address+0xb3/0x175 [bridge]
[<
000000001de02dbd>] br_stp_change_bridge_id+0xf/0xff [bridge]
[<
00000000ac0e32b1>] br_set_mac_address+0x76/0x99 [bridge]
[<
000000006846a77f>] dev_set_mac_address+0x63/0x9b
[<
00000000d30738fc>] __bond_release_one+0x3f6/0x455 [bonding]
[<
00000000fc7ec01d>] bond_netdev_event+0x2f2/0x400 [bonding]
[<
00000000305d7795>] notifier_call_chain+0x38/0x56
[<
0000000028885d4a>] call_netdevice_notifiers+0x1e/0x23
[<
000000008279477b>] rollback_registered_many+0x353/0x6a4
[<
0000000018ef753a>] unregister_netdevice_many+0x17/0x6f
[<
00000000ba854b7a>] rtnl_delete_link+0x3c/0x43
[<
00000000adf8618d>] rtnl_dellink+0x1dc/0x20a
[<
000000009b6395fd>] rtnetlink_rcv_msg+0x23d/0x268
Fixes:
43598813386f ("bridge: add local MAC address to forwarding table (v2)")
Reported-by: syzbot+2add91c08eb181fea1bf@syzkaller.appspotmail.com
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 3 Dec 2019 14:12:39 +0000 (17:12 +0300)]
net: fix a leak in register_netdevice()
We have to free "dev->name_node" on this error path.
Fixes:
ff92741270bf ("net: introduce name_node struct to be used in hashlist")
Reported-by: syzbot+6e13e65ffbaa33757bcb@syzkaller.appspotmail.com
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 3 Dec 2019 19:14:41 +0000 (11:14 -0800)]
Merge tag 'linux-can-fixes-for-5.5-
20191203' of git://git./linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2019-12-03
this is a pull request of 6 patches for net/master.
The first two patches are against the MAINTAINERS file and adds Appana
Durga Kedareswara rao as maintainer for the xilinx-can driver and Sriram
Dash for the m_can (mmio) driver.
The next patch is by Jouni Hogander and fixes a use-after-free in the
slcan driver.
Johan Hovold's patch for the ucan driver fixes the non-atomic allocation
in the completion handler.
The last two patches target the xilinx-can driver. The first one is by
Venkatesh Yadav Abbarapu and skips the error message on deferred probe,
the second one is by Srinivas Neeli and fixes the usage of the skb after
can_put_echo_skb().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Srinivas Neeli [Mon, 2 Dec 2019 13:02:11 +0000 (18:32 +0530)]
can: xilinx_can: Fix usage of skb memory
As per linux can framework, driver not allowed to touch the skb memory
after can_put_echo_skb() call.
This patch fixes the same.
https://www.spinics.net/lists/linux-can/msg02199.html
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Appana Durga Kedareswara Rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Venkatesh Yadav Abbarapu [Mon, 2 Dec 2019 13:02:10 +0000 (18:32 +0530)]
can: xilinx_can: skip error message on deferred probe
When the CAN bus clock is provided from the clock wizard, clock wizard
driver may not be available when can driver probes resulting to the
error message "bus clock not found error".
As this error message is not very useful to the end user, skip printing
in the case of deferred probe.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Appana Durga Kedareswara Rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Johan Hovold [Thu, 28 Nov 2019 18:26:03 +0000 (19:26 +0100)]
can: ucan: fix non-atomic allocation in completion handler
USB completion handlers are called in atomic context and must
specifically not allocate memory using GFP_KERNEL.
Fixes:
9f2d3eae88d2 ("can: ucan: add driver for Theobroma Systems UCAN devices")
Cc: stable <stable@vger.kernel.org> # 4.19
Cc: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Cc: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jouni Hogander [Wed, 27 Nov 2019 06:40:26 +0000 (08:40 +0200)]
can: slcan: Fix use-after-free Read in slcan_open
Slcan_open doesn't clean-up device which registration failed from the
slcan_devs device list. On next open this list is iterated and freed
device is accessed. Fix this by calling slc_free_netdev in error path.
Driver/net/can/slcan.c is derived from slip.c. Use-after-free error was
identified in slip_open by syzboz. Same bug is in slcan.c. Here is the
trace from the Syzbot slip report:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374
__kasan_report.cold+0x1b/0x41 mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:634
__asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:132
sl_sync drivers/net/slip/slip.c:725 [inline]
slip_open+0xecd/0x11b7 drivers/net/slip/slip.c:801
tty_ldisc_open.isra.0+0xa3/0x110 drivers/tty/tty_ldisc.c:469
tty_set_ldisc+0x30e/0x6b0 drivers/tty/tty_ldisc.c:596
tiocsetd drivers/tty/tty_io.c:2334 [inline]
tty_ioctl+0xe8d/0x14f0 drivers/tty/tty_io.c:2594
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0xdb6/0x13e0 fs/ioctl.c:696
ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl fs/ioctl.c:718 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
do_syscall_64+0xfa/0x760 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes:
ed50e1600b44 ("slcan: Fix memory leak in error path")
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David Miller <davem@davemloft.net>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.4
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sriram Dash [Tue, 3 Dec 2019 04:29:09 +0000 (09:59 +0530)]
MAINTAINERS: add myself as maintainer of MCAN MMIO device driver
Since we are actively working on MMIO MCAN device driver,
as discussed with Marc, I am adding myself as a maintainer.
Signed-off-by: Sriram Dash <sriram.dash@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Appana Durga Kedareswara rao [Thu, 21 Nov 2019 08:39:24 +0000 (14:09 +0530)]
MAINTAINERS: add fragment for xilinx CAN driver
Added entry for xilinx CAN driver.
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Martin Varghese [Mon, 2 Dec 2019 05:19:51 +0000 (10:49 +0530)]
Fixed updating of ethertype in function skb_mpls_pop
The skb_mpls_pop was not updating ethertype of an ethernet packet if the
packet was originally received from a non ARPHRD_ETHER device.
In the below OVS data path flow, since the device corresponding to port 7
is an l3 device (ARPHRD_NONE) the skb_mpls_pop function does not update
the ethertype of the packet even though the previous push_eth action had
added an ethernet header to the packet.
recirc_id(0),in_port(7),eth_type(0x8847),
mpls(label=12/0xfffff,tc=0/0,ttl=0/0x0,bos=1/1),
actions:push_eth(src=00:00:00:00:00:00,dst=00:00:00:00:00:00),
pop_mpls(eth_type=0x800),4
Fixes:
ed246cee09b9 ("net: core: move pop MPLS functionality from OvS to core helper")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Victorien Molle [Mon, 2 Dec 2019 14:11:38 +0000 (15:11 +0100)]
sch_cake: Add missing NLA policy entry TCA_CAKE_SPLIT_GSO
This field has never been checked since introduction in mainline kernel
Signed-off-by: Victorien Molle <victorien.molle@wifirst.fr>
Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr>
Fixes:
2db6dc2662ba "sch_cake: Make gso-splitting configurable from userspace"
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 2 Dec 2019 18:50:29 +0000 (10:50 -0800)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2019-12-02
The following pull-request contains BPF updates for your *net* tree.
We've added 10 non-merge commits during the last 6 day(s) which contain
a total of 10 files changed, 60 insertions(+), 51 deletions(-).
The main changes are:
1) Fix vmlinux BTF generation for binutils pre v2.25, from Stanislav Fomichev.
2) Fix libbpf global variable relocation to take symbol's st_value offset
into account, from Andrii Nakryiko.
3) Fix libbpf build on powerpc where check_abi target fails due to different
readelf output format, from Aurelien Jarno.
4) Don't set BPF insns RO for the case when they are JITed in order to avoid
fragmenting the direct map, from Daniel Borkmann.
5) Fix static checker warning in btf_distill_func_proto() as well as a build
error due to empty enum when BPF is compiled out, from Alexei Starovoitov.
6) Fix up generation of bpf_helper_defs.h for perf, from Arnaldo Carvalho de Melo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Aurelien Jarno [Sun, 1 Dec 2019 19:57:28 +0000 (20:57 +0100)]
libbpf: Fix readelf output parsing on powerpc with recent binutils
On powerpc with recent versions of binutils, readelf outputs an extra
field when dumping the symbols of an object file. For example:
35:
0000000000000838 96 FUNC LOCAL DEFAULT [<localentry>: 8] 1 btf_is_struct
The extra "[<localentry>: 8]" prevents the GLOBAL_SYM_COUNT variable to
be computed correctly and causes the check_abi target to fail.
Fix that by looking for the symbol name in the last field instead of the
8th one. This way it should also cope with future extra fields.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/bpf/20191201195728.4161537-1-aurelien@aurel32.net
Linus Torvalds [Mon, 2 Dec 2019 04:36:41 +0000 (20:36 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge updates from Andrew Morton:
"Incoming:
- a small number of updates to scripts/, ocfs2 and fs/buffer.c
- most of MM
I still have quite a lot of material (mostly not MM) staged after
linux-next due to -next dependencies. I'll send those across next week
as the preprequisites get merged up"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (135 commits)
mm/page_io.c: annotate refault stalls from swap_readpage
mm/Kconfig: fix trivial help text punctuation
mm/Kconfig: fix indentation
mm/memory_hotplug.c: remove __online_page_set_limits()
mm: fix typos in comments when calling __SetPageUptodate()
mm: fix struct member name in function comments
mm/shmem.c: cast the type of unmap_start to u64
mm: shmem: use proper gfp flags for shmem_writepage()
mm/shmem.c: make array 'values' static const, makes object smaller
userfaultfd: require CAP_SYS_PTRACE for UFFD_FEATURE_EVENT_FORK
fs/userfaultfd.c: wp: clear VM_UFFD_MISSING or VM_UFFD_WP during userfaultfd_register()
userfaultfd: wrap the common dst_vma check into an inlined function
userfaultfd: remove unnecessary WARN_ON() in __mcopy_atomic_hugetlb()
userfaultfd: use vma_pagesize for all huge page size calculation
mm/madvise.c: use PAGE_ALIGN[ED] for range checking
mm/madvise.c: replace with page_size() in madvise_inject_error()
mm/mmap.c: make vma_merge() comment more easy to understand
mm/hwpoison-inject: use DEFINE_DEBUGFS_ATTRIBUTE to define debugfs fops
autonuma: reduce cache footprint when scanning page tables
autonuma: fix watermark checking in migrate_balanced_pgdat()
...
Linus Torvalds [Mon, 2 Dec 2019 04:35:03 +0000 (20:35 -0800)]
Merge git://git./linux/kernel/git/netdev/net
Pull networking fixes from David Miller:
1) Fix several scatter gather list issues in kTLS code, from Jakub
Kicinski.
2) macb driver device remove has to kill the hresp_err_tasklet. From
Chuhong Yuan.
3) Several memory leak and reference count bug fixes in tipc, from Tung
Nguyen.
4) Fix mlx5 build error w/o ipv6, from Yue Haibing.
5) Fix jumbo frame and other regressions in r8169, from Heiner
Kallweit.
6) Undo some BUG_ON()'s and replace them with WARN_ON_ONCE and proper
error propagation/handling. From Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (24 commits)
openvswitch: remove another BUG_ON()
openvswitch: drop unneeded BUG_ON() in ovs_flow_cmd_build_info()
net: phy: realtek: fix using paged operations with RTL8105e / RTL8208
r8169: fix resume on cable plug-in
r8169: fix jumbo configuration for RTL8168evl
net: emulex: benet: indent a Kconfig depends continuation line
selftests: forwarding: fix race between packet receive and tc check
net: sched: fix `tc -s class show` no bstats on class with nolock subqueues
net: ethernet: ti: ale: ensure vlan/mdb deleted when no members
net/mlx5e: Fix build error without IPV6
selftests: pmtu: use -oneline for ip route list cache
tipc: fix duplicate SYN messages under link congestion
tipc: fix wrong timeout input for tipc_wait_for_cond()
tipc: fix wrong socket reference counter after tipc_sk_timeout() returns
tipc: fix potential memory leak in __tipc_sendmsg()
net: macb: add missed tasklet_kill
selftests: bpf: correct perror strings
selftests: bpf: test_sockmap: handle file creation failures gracefully
net/tls: use sg_next() to walk sg entries
net/tls: remove the dead inplace_crypto code
...
Linus Torvalds [Mon, 2 Dec 2019 03:05:07 +0000 (19:05 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Various fixes:
- Fix the PAT performance regression that downgraded write-combining
device memory regions to uncached.
- There's been a number of bugs in 32-bit double fault handling -
hopefully all fixed now.
- Fix an LDT crash
- Fix an FPU over-optimization that broke with GCC9 code
optimizations.
- Misc cleanups"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/pat: Fix off-by-one bugs in interval tree search
x86/ioperm: Save an indentation level in tss_update_io_bitmap()
x86/fpu: Don't cache access to fpu_fpregs_owner_ctx
x86/entry/32: Remove unused 'restore_all_notrace' local label
x86/ptrace: Document FSBASE and GSBASE ABI oddities
x86/ptrace: Remove set_segment_reg() implementations for current
x86/traps: die() instead of panicking on a double fault
x86/doublefault/32: Rewrite the x86_32 #DF handler and unify with 64-bit
x86/doublefault/32: Move #DF stack and TSS to cpu_entry_area
x86/doublefault/32: Rename doublefault.c to doublefault_32.c
x86/traps: Disentangle the 32-bit and 64-bit doublefault code
lkdtm: Add a DOUBLE_FAULT crash type on x86
selftests/x86/single_step_syscall: Check SYSENTER directly
x86/mm/32: Sync only to VMALLOC_END in vmalloc_sync_all()
Linus Torvalds [Mon, 2 Dec 2019 02:49:57 +0000 (18:49 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
- Make /sys/devices/cpu/rdpmc based RDPMC enforcement more
instantaneous
- decoder: Update the Intel opcode map
- Various tooling fixes, including a few late optimizations and
cleanups.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
perf script: Fix invalid LBR/binary mismatch error
perf script: Fix brstackinsn for AUXTRACE
perf affinity: Add infrastructure to save/restore affinity
perf pmu: Use file system cache to optimize sysfs access
perf regs: Make perf_reg_name() return "unknown" instead of NULL
perf diff: Use llabs() with 64-bit values
perf diff: Use llabs() with 64-bit values
perf/x86: Implement immediate enforcement of /sys/devices/cpu/rdpmc value of 0
perf tools: Allow to link with libbpf dynamicaly
perf tests: Rename tests/map_groups.c to tests/maps.c
perf tests: Rename thread-mg-share to thread-maps-share
perf maps: Rename map_groups.h to maps.h
perf maps: Rename 'mg' variables to 'maps'
perf map_symbol: Rename ms->mg to ms->maps
perf addr_location: Rename al->mg to al->maps
perf thread: Rename thread->mg to thread->maps
perf maps: Merge 'struct maps' with 'struct map_groups'
x86/insn: perf tools: Add some more instructions to the new instructions test
x86/insn: Add some more Intel instructions to the opcode map
perf map: Remove unused functions
...