USB: gadget: udc: fix wrong pointer passed to IS_ERR() and PTR_ERR()

IS_ERR() and PTR_ERR() use wrong pointer, it should be
udc->virt_addr, fix it.

Fixes: 1b9f35adb0ff ("usb: gadget: udc: Add Synopsys UDC Platform driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210330130159.1051979-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: delete duplicate word in the comment

Delete the duplicate word "from" in comment.

Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Link: https://lore.kernel.org/r/1616988403-48755-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: add parenthess and space around *

Just fix the following checkpatch error:
ERROR: Macros with complex values should be enclosed in parentheses.

Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Link: https://lore.kernel.org/r/1617001556-61868-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: aspeed: fix dma map failure

Currently the virtual port_dev device is passed to DMA API, and this is
wrong because the device passed to DMA API calls must be the actual
hardware device performing the DMA.

The patch replaces usb_gadget_map_request/usb_gadget_unmap_request APIs
with usb_gadget_map_request_by_dev/usb_gadget_unmap_request_by_dev APIs
so the DMA capable platform device can be passed to the DMA APIs.

The patch fixes below backtrace detected on Facebook AST2500 OpenBMC
platforms:

[<80106550>] show_stack+0x20/0x24
[<80106868>] dump_stack+0x28/0x30
[<80823540>] __warn+0xfc/0x110
[<8011ac30>] warn_slowpath_fmt+0xb0/0xc0
[<8011ad44>] dma_map_page_attrs+0x24c/0x314
[<8016a27c>] usb_gadget_map_request_by_dev+0x100/0x1e4
[<805cedd8>] usb_gadget_map_request+0x1c/0x20
[<805cefbc>] ast_vhub_epn_queue+0xa0/0x1d8
[<7f02f710>] usb_ep_queue+0x48/0xc4
[<805cd3e8>] ecm_do_notify+0xf8/0x248
[<7f145920>] ecm_set_alt+0xc8/0x1d0
[<7f145c34>] composite_setup+0x680/0x1d30
[<7f00deb8>] ast_vhub_ep0_handle_setup+0xa4/0x1bc
[<7f02ee94>] ast_vhub_dev_irq+0x58/0x84
[<7f0309e0>] ast_vhub_irq+0xb0/0x1c8
[<7f02e118>] __handle_irq_event_percpu+0x50/0x19c
[<8015e5bc>] handle_irq_event_percpu+0x38/0x8c
[<8015e758>] handle_irq_event+0x38/0x4c

Fixes: 7ecca2a4080c ("usb/gadget: Add driver for Aspeed SoC virtual hub")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20210331045831.28700-1-rentao.bupt@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: add cancelled reasons for dwc3 requests

Currently, when dwc3 handles request cancelled, dwc3 just returns
-ECONNRESET for all requests. It will cause USB function drivers
can't know if the requests are cancelled by other reasons.

This patch will replace DWC3_REQUEST_STATUS_CANCELLED with the
reasons below.
  - DWC3_REQUEST_STATUS_DISCONNECTED
  - DWC3_REQUEST_STATUS_DEQUEUED
  - DWC3_REQUEST_STATUS_STALLED

Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Ray Chi <raychi@google.com>
Link: https://lore.kernel.org/r/20210327181742.1810969-1-raychi@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: dts: imx8mp: Use the correct name for child node "snps, dwc3"

After the node name of "snps,dwc3" has been corrected to start with "usb"
in fsl,imx8mp-dwc3.yaml. Its name in dts should be modified accordingly.

Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210329072714.2135-3-thunder.leizhen@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: dwc3-imx8mp: Use the correct name for child node "snps, dwc3"

File snps,dwc3.yaml describes the schema of Synopsys DesignWare USB3
Controller, it directly or indirectly contains "$ref: usb.yaml". So the
node name of "snps,dwc3" must start with "usb". Otherwise, the following
warning will be displayed:

Documentation/devicetree/bindings/usb/fsl,imx8mp-dwc3.example.dt.yaml: \
dwc3@38100000: $nodename:0: 'dwc3@38100000' does not match '^usb(@.*)?'
        From schema: Documentation/devicetree/bindings/usb/snps,dwc3.yaml

In addition, replace "type: object" with "$ref: snps,dwc3.yaml#". Ensure
that all properties of the child node comply with snps,dwc3.yaml.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210329072714.2135-2-thunder.leizhen@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: exynos: fix incorrect kernel-doc comment syntax

The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for drivers/usb/dwc3/dwc3-exynos.c follows this syntax, but the
content inside does not comply with kernel-doc.

This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warning from kernel-doc:
"warning: expecting prototype for dwc3(). Prototype was for DWC3_EXYNOS_MAX_CLOCKS() instead"

Provide a simple fix by replacing this occurrence with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Link: https://lore.kernel.org/r/20210329140318.27742-1-yashsri421@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: fix incorrect kernel-doc comment syntax in files

The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
There are certain files in drivers/usb/dwc3, which follow this syntax,
but the content inside does not comply with kernel-doc.
Such lines were probably not meant for kernel-doc parsing, but are parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warnings from kernel-doc.

E.g., presence of kernel-doc like comment in drivers/usb/dwc3/io.h at
header causes this warnings by kernel-doc:
"warning: expecting prototype for h(). Prototype was for __DRIVERS_USB_DWC3_IO_H() instead"

Similarly for other files too.

Provide a simple fix by replacing such occurrences with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.

Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Link: https://lore.kernel.org/r/20210329135108.27128-1-yashsri421@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: st: fix incorrect kernel-doc comment syntax in file

The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for drivers/usb/dwc3/dwc3-st.c follows this syntax, but the
content inside does not comply with kernel-doc.

This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warning from kernel-doc:
"warning: expecting prototype for dwc3(). Prototype was for CLKRST_CTRL() instead"

Provide a simple fix by replacing this occurrence with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.

Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Link: https://lore.kernel.org/r/20210329132014.24304-1-yashsri421@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: imx8mp: fix incorrect kernel-doc comment syntax

The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for drivers/usb/dwc3/dwc3-imx8mp.c follows this syntax, but the
content inside does not comply with kernel-doc.

This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warning from kernel-doc:
"warning: expecting prototype for dwc3(). Prototype was for USB_WAKEUP_CTRL() instead"

Provide a simple fix by replacing this occurrence with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Link: https://lore.kernel.org/r/20210329142604.28737-1-yashsri421@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: s3c: Fix the error handling path in 's3c2410_udc_probe()'

Some 'clk_prepare_enable()' and 'clk_get()' must be undone in the error
handling path of the probe function, as already done in the remove
function.

Fixes: 3fc154b6b813 ("USB Gadget driver for Samsung s3c2410 ARM SoC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/2bee52e4ce968f48b4c32545cf8f3b2ab825ba82.1616830026.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: s3c: Fix incorrect resources releasing

Since commit 188db4435ac6 ("usb: gadget: s3c: use platform resources"),
'request_mem_region()' and 'ioremap()' are no more used, so they don't need
to be undone in the error handling path of the probe and in the remove
function.

Remove these calls and the unneeded 'rsrc_start' and 'rsrc_len' global
variables.

Fixes: 188db4435ac6 ("usb: gadget: s3c: use platform resources")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/b317638464f188159bd8eea44427dd359e480625.1616830026.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: Create helper function getting MDWIDTH

Different controller IPs check different HW parameters for MDWIDTH.
To help with maintainability, create a helper function to consolidate
the logic in a single place.

Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/456329d36e8c188df5c234f3282595b630bf1470.1616892233.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: usb-nop-xceiv: Convert to DT schema

Convert the usb-nop-xceiv binding to DT schema.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210327202816.545282-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: mediatek,mtu3: Use graph schema

Users of the DT graph binding now should reference it for their 'port'
schemas, so add it for Mediatek MTU3 binding.

Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210327191448.410795-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: dts: mt8183: update wakeup register offset

Use wakeup control register offset exactly, and update revision
number

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-13-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci-mtk: remove MODULE_ALIAS

Since the driver only supports the devices created by the OF
core, seems no need MODULE_ALIAS() anymore.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-9-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci-mtk: drop CONFIG_OF

The driver can match only the devices created by the OF core
via the DT table, so the table should be always used.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-8-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: mtu3: support wakeup for mt8183 and mt8192

These two HW of wakeup don't follow MediaTek internal IPM rule,
and both use a specific way, like as early revision of mt8173.

Due to the index 2 already used by many DTS, it's better to keep
it unchanged for backward compatibility, treat specific ones without
following IPM rule as revision 1.x, meanwhile reserve 3~99 for
later revision that following the IPM rule.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1616482975-17841-3-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: mtk-xhci: add support wakeup for mt8183 and mt8192

These two HW of wakeup don't follow MediaTek internal IPM rule,
both use a specific way, like as early revision of mt8173.

Due to the index 2 already used by many DTS, it's better to keep
it unchanged for backward compatibility, treat specific ones without
following IPM rule as revision 1.x, meanwhile reserve 3~99 for
later revisions with following the IPM rule.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1616482975-17841-2-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: misc: usbsevseg: update to use usb_control_msg_send()

The newer usb_control_msg_{send|recv}() API ensures that a short read is
treated as an error, data can be used off the stack, and raw usb pipes
need not be created in the calling functions.
For this reason, instances of usb_control_msg() have been replaced with
usb_control_msg_send() appropriately.

Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20210326223251.753952-4-anant.thazhemadam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: misc: ezusb: update to use usb_control_msg_send()

The newer usb_control_msg_{send|recv}() API ensures that a short read is
treated as an error, data can be used off the stack, and raw usb pipes need
not be created in the calling functions.
For this reason, the instance of usb_control_msg() has been replaced with
usb_control_msg_send() appropriately.

Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20210326223251.753952-3-anant.thazhemadam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: misc: ehset: update to use the usb_control_msg_{send|recv}() API

The newer usb_control_msg_{send|recv}() API ensures that a short read
is treated as an error, data can be used off the stack, and raw usb
pipes need not be created in the calling functions.
For this reason, instances of usb_control_msg() have been replaced with
usb_control_msg_{recv|send}() appropriately.

Now, we also test for a short device descriptor (which USB core
should already have fetched if you get to probe this driver), but which
wasn't verified again here before.

Reviewed-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20210326223251.753952-2-anant.thazhemadam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power: supply: Fix build error when CONFIG_POWER_SUPPLY is not enabled.

The build error happens when CONFIG_POWER_SUPPLY is not enabled.

h8300-linux-ld: drivers/usb/dwc3/gadget.o: in function `.L59':
>> gadget.c:(.text+0x655): undefined reference to `power_supply_set_property'

Fixes: 99288de36020 ("usb: dwc3: add an alternate path in vbus_draw callback")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ray Chi <raychi@google.com>
Link: https://lore.kernel.org/r/20210327182809.1814480-3-raychi@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: gadget: modify the scale in vbus_draw callback

Currently, vbus_draw callback used wrong scale for power_supply.
The unit of power supply should be uA.
Therefore, this patch will fix this problem.

Fixes: 99288de36020 ("usb: dwc3: add an alternate path in vbus_draw callback")
Reported-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Ray Chi <raychi@google.com>
Link: https://lore.kernel.org/r/20210327182809.1814480-2-raychi@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: mtu3: drop CONFIG_OF

The driver can match only the devices created by the OF core
via the DT table, so the table should be always used.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-12-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: mtu3: add support ip-sleep wakeup for MT8192

Add add support ip-sleep wakeup for MT8192, it's a specific
revision, not following IPM rule.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-11-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: mtu3: support ip-sleep wakeup for MT8183

Add support ip-sleep wakeup for MT8183, it's similar to MT8173,
and it's also a specific one, but not following IPM rule.
Due to the index 2 already used by many DTS, it's better to keep
it unchanged for backward compatibility, treat specific ones without
following IPM rule as revision 1.x, meanwhile reserve 3~10 for later
revision that follows the IPM rule.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-10-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci-mtk: add support ip-sleep wakeup for mT8192

Add support ip-sleep wakeup for mT8192, it's a specific revision,
and not following IPM rule.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-7-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci-mtk: support ip-sleep wakeup for MT8183

Add support ip-sleep wakeup for MT8183, it's similar to MT8173,
and it's also a specific one, but not following IPM rule.
Due to the index 2 already used by many DTS, it's better to keep
it unchanged for backward compatibility, treat specific ones without
following IPM rule as revision 1.x, meanwhile reserve 3~10 for
later revision that follows the IPM rule.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-6-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: pch_udc: Convert Intel Quark quirk to use driver data

Unify quirks, in particular one for Intel Quark, to use driver data
and accompanying infrastructure.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210325135508.70350-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: pch_udc: Use PCI sub IDs instead of DMI

We don't need DMI to identify Intel Minnowboard (v1) since it has
properly set PCI sub IDs. So, drop unneeded DMI level of identification.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210325135508.70350-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: pch_udc: Remove CONFIG_PM_SLEEP ifdefery

Use __maybe_unused for the suspend()/resume() hooks and get rid of
the CONFIG_PM_SLEEP ifdefery to improve the code.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210325135508.70350-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: pch_udc: switch over to usb_gadget_map/unmap_request()

We have generic implementations for a reason, let's use them.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210325135508.70350-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fotg210-udc: Complete OUT requests on short packets

A short packet indicates the end of a transfer and marks the request as
complete.

Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-8-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fotg210-udc: Don't DMA more than the buffer can take

Before this, it wrote as much as available into the buffer, even if it
didn't fit.

Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-7-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fotg210-udc: Call usb_gadget_udc_reset

Notify the UDC core that a bus reset occurred.

Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-6-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fotg210-udc: Mask GRP2 interrupts we don't handle

Currently it leaves unhandled interrupts unmasked, but those are never
acked. In the case of a "device idle" interrupt, this leads to an
effectively frozen system until plugging it in.

Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-5-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fotg210-udc: Remove a dubious condition leading to fotg210_done

When the EP0 IN request was not completed but less than a packet sent,
it would complete the request successfully. That doesn't make sense
and can't really happen as fotg210_start_dma always sends
min(length, maxpkt) bytes.

Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-4-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fotg210-udc: Fix EP0 IN requests bigger than two packets

For a 134 Byte packet, it sends the first two 64 Byte packets just fine,
but then notice that less than a packet is remaining and call fotg210_done
without actually sending the rest.

Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-3-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fotg210-udc: Fix DMA on EP0 for length > max packet size

For a 75 Byte request, it would send the first 64 separately, then detect
that the remaining 11 Byte fit into a single DMA, but due to this bug set
the length to the original 75 Bytes. This leads to a DMA failure (which is
ignored...) and the request completes without the remaining bytes having
been sent.

Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-2-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: qcom,dwc3: Add bindings for SC7280

Add the compatible string for sc7280 SoC from Qualcomm.

Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1615978901-4202-2-git-send-email-sanm@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: trace: Print register read and write offset

Currently dwc3 only prints the virtual address of a register when doing
register read/write. However, these hashed addresses are difficult to read.
Also, since we use %p, we may get some useless (___ptrval___) prints if the
address is not randomized enough. Let's include the register offset to help
read the register read and write tracepoints.

Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/cb38aa7dec109a8965691b53039a8b317d026189.1616636706.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: tcpci_maxim: Make symbol 'max_tcpci_tcpci_write_table' static

The sparse tool complains as follows:

drivers/usb/typec/tcpm/tcpci_maxim.c:55:34: warning:
 symbol 'max_tcpci_tcpci_write_table' was not declared. Should it be static?

This symbol is not used outside of tcpci_maxim.c, so this
commit marks it static.

Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210324144253.1011234-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usbip: tools: add usage of device mode in usbip_list.c

The option '-d/--device' was implemented in 'usbip list' but not
shown in usage. Hence this commit adds this option to usage.

Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hongren Zheng <i@zenithal.me>
Link: https://lore.kernel.org/r/YFrwq75Uyef3c9gz@Sun
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usbip: tools: add options and examples in man page related to device mode

The commit e0546fd8b748 ("usbip: tools: Start using VUDC backend in
usbip tools") implemented device mode for user space tools, however the
corresponding options are not documented in man page.

This commit documents the options and provides examples on device mode.
Also the command `usbip port` is documented.

Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hongren Zheng <i@zenithal.me>
Link: https://lore.kernel.org/r/YFrdyKKx1nx8bktm@Sun
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tools: usbip: list.h: fix kernel-doc for list_del()

In list.h, the kernel-doc for list_del() should be immediately
preceding the implementation and not separated from it by
another function implementation.

Eliminates this kernel-doc error:
list.h:1: warning: 'list_del' not found

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210325174724.14447-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: Fix a typo

s/Acknowlege/Acknowledge/

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Link: https://lore.kernel.org/r/20210325051023.27914-1-unixbhaskar@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: pch_udc: Provide a GPIO line used on Intel Minnowboard (v1)

Intel Minnowboard (v1) uses SCH GPIO line SUS7 (i.e. 12)
for VBUS sense. Provide a DMI based quirk to have it's being used.

Fixes: e20849a8c883 ("usb: gadget: pch_udc: Convert to use GPIO descriptors")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: pch_udc: Initialize device pointer before use

During conversion to use GPIO descriptors the device pointer,
which is applied to devm_gpiod_get(), is not yet initialized.

Move initialization in the ->probe() in order to have it set before use.

Fixes: e20849a8c883 ("usb: gadget: pch_udc: Convert to use GPIO descriptors")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: pch_udc: Revert d3cb25a12138 completely

The commit d3cb25a12138 ("usb: gadget: udc: fix spin_lock in pch_udc")
obviously was not thought through and had made the situation even worse
than it was before. Two changes after almost reverted it. but a few
leftovers have been left as it. With this revert d3cb25a12138 completely.

While at it, narrow down the scope of unlocked section to prevent
potential race when prot_stall is assigned.

Fixes: d3cb25a12138 ("usb: gadget: udc: fix spin_lock in pch_udc")
Fixes: 9903b6bedd38 ("usb: gadget: pch-udc: fix lock")
Fixes: 1d23d16a88e6 ("usb: gadget: pch_udc: reorder spin_[un]lock to avoid deadlock")
Cc: Iago Abal <mail@iagoabal.eu>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: pch_udc: Move pch_udc_init() to satisfy kernel doc

Kernel doc and the content described by it shouldn't be torn apart.
Otherwise validator is not happy:

.../pch_udc.c:573: warning: expecting prototype for pch_udc_reconnect(). Prototype was for pch_udc_init() instead

Fixes: 1c575d2d2e3f ("usb: gadget: pch_udc: Fix usb/gadget/pch_udc: Fix ether gadget connect/disconnect issue")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: pch_udc: Check for DMA mapping error

DMA mapping might fail, we have to check it with dma_mapping_error().
Otherwise DMA-API is not happy:

  DMA-API: pch_udc 0000:02:02.4: device driver failed to check map error[device address=0x00000000027ee678] [size=64 bytes] [mapped as single]

Fixes: abab0c67c061 ("usb: pch_udc: Fixed issue which does not work with g_serial")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: pch_udc: Check if driver is present before calling ->setup()

Since we have a separate routine for VBUS sense, the interrupt may occur
before gadget driver is present. Hence, ->setup() call may oops the kernel:

[   55.245843] BUG: kernel NULL pointer dereference, address: 00000010
...
[   55.245843] EIP: pch_udc_isr.cold+0x162/0x33f
...
[   55.245843]  <IRQ>
[   55.245843]  ? pch_udc_svc_data_out+0x160/0x160

Check if driver is present before calling ->setup().

Fixes: f646cf94520e ("USB device driver of Topcliff PCH")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: pch_udc: Replace cpu_to_le32() by lower_32_bits()

Either way ~0 will be in the correct byte order, hence
replace cpu_to_le32() by lower_32_bits(). Moreover,
it makes sparse happy, otherwise it complains:

.../pch_udc.c:1813:27: warning: incorrect type in assignment (different base types)
.../pch_udc.c:1813:27:    expected unsigned int [usertype] dataptr
.../pch_udc.c:1813:27:    got restricted __le32 [usertype]

Fixes: f646cf94520e ("USB device driver of Topcliff PCH")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci: Remove unused function

Now that we replaced the xhci_create_usb3_bos_desc() function. We can
remove it along with the static usb_bos_descriptor structure.

Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ce0acbbd0bd3c3c3a08e6418ab3bdb431a44bbfd.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci: Rewrite xhci_create_usb3_bos_desc()

The current xhci_create_usb3_bos_desc() uses a static bos u8 array and
various magic numbers and offsets making it difficult to extend support
for USB 3.2. Let's rewrite this entire function to support dual-lane in
USB 3.2.

The hub driver matches the port speed ID from the extended port status
to the SSID of the sublink speed attributes to detect if the device
supports SuperSpeed Plus. Currently we don't provide the default gen1x2
and gen2x2 sublink speed capability descriptor for USB 3.2 roothub. The
USB stack depends on this to detect and match the correct speed.
In addition, if the xHCI host provides Protocol Speed ID (PSI)
capability, then make sure to convert Protocol Speed ID Mantissa and
Exponent (PSIM & PSIE) to lane speed for gen1x2 and gen2x2.

Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/19cd09b03f96346996270579fd27d38b8a6844aa.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci: Fix port minor revision

Some hosts incorrectly use sub-minor version for minor version (i.e.
0x02 instead of 0x20 for bcdUSB 0x320 and 0x01 for bcdUSB 0x310).
Currently the xHCI driver works around this by just checking for minor
revision > 0x01 for USB 3.1 everywhere. With the addition of USB 3.2,
checking this gets a bit cumbersome. Since there is no USB release with
bcdUSB 0x301 to 0x309, we can assume that sub-minor version 01 to 09 is
incorrect. Let's try to fix this and use the minor revision that matches
with the USB/xHCI spec to help with the version checking within the
driver.

Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ed330e95a19dc367819c5b4d78bf7a541c35aa0a.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci: Init root hub SSP rate

Initialize USB 3.x root hub SuperSpeed Plus rate.

Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f1698a96d5f9dfaefb857b95e5db6135ae0c9e93.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: gadget: f_fs: fix memdup_user.cocci warnings

drivers/usb/gadget/function/f_fs.c:3829:8-15: WARNING opportunity for memdup_user

 Use memdup_user rather than duplicating its implementation
 This is a little bit restricted to reduce false positives

Generated by: scripts/coccinelle/api/memdup_user.cocci

Fixes: 8704fd73bf56 ("USB: gadget: f_fs: remove likely/unlikely")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20210308070951.GA83949@8a16bdd473dc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: legacy: fix error return code of msg_bind()

When usb_otg_descriptor_alloc() returns NULL to usb_desc, no error
return code of msg_bind() is assigned.
To fix this bug, status is assigned with -ENOMEM in this case.

Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20210323123648.3997-1-baijiaju1990@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: core: sysfs: Check for SSP rate in speed attr

Check for usb_device->ssp_rate to output the signaling rate for genXxY.

Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/80a3214592b30da6ca95bb87984f2a9779de0b14.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: core: hub: Print speed name based on ssp rate

Check for usb_device->ssp_rate to print the SuperSpeed Plus signaling
rate generation and lane count.

Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/df0986bbe92251c104dd92e3c796df7c4f2674ce.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: core: hub: Remove port_speed_is_ssp()

The get_port_ssp_rate() can replace port_speed_is_ssp(). If the port
speed is detected to be in gen2x1, gen1x2, or gen2x2, then the port is
operating at SuperSpeed Plus.

Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/dfd61ae637597bad502d2420b4dbd3774fc76aab.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: core: Track SuperSpeed Plus GenXxY

Introduce ssp_rate field to usb_device structure to capture the
connected SuperSpeed Plus signaling rate generation and lane count with
the corresponding usb_ssp_rate enum.

Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/b7805d121e5ae4ad5ae144bd860b6ac04ee47436.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: gadget: Ignore EP queue requests during bus reset

The current dwc3_gadget_reset_interrupt() will stop any active
transfers, but only addresses blocking of EP queuing for while we are
coming from a disconnected scenario, i.e. after receiving the disconnect
event.  If the host decides to issue a bus reset on the device, the
connected parameter will still be set to true, allowing for EP queuing
to continue while we are disabling the functions.  To avoid this, set the
connected flag to false until the stop active transfers is complete.

Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1616146285-19149-3-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: gadget: Avoid continuing preparing TRBs during teardown

Add checks similar to dwc3_gadget_ep_queue() before kicking off
transfers after getting an endpoint completion event.   Since cleaning
up completed requests will momentarily unlock dwc->lock, there is a
chance for a sequence like pullup disable to be executed.  This can
lead to preparing a TRB, which will be removed by the pullup disable
routine.

Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1616146285-19149-2-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: xhci: drop workaround for forced irq threading

Force-threaded interrupt handlers used to run with interrupts enabled,
something which could lead to deadlocks in case a threaded handler
shared a lock with code running in hard interrupt context (e.g. timer
callbacks) and did not explicitly disable interrupts.

Since commit 81e2073c175b ("genirq: Disable interrupts for force
threaded handlers") interrupt handlers always run with interrupts
disabled on non-RT so that drivers no longer need to do handle forced
threading ("threadirqs").

Drop the now obsolete workaround added by commit 63aea0dbab90 ("USB:
xhci: fix lock-inversion problem").

Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322111140.32056-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: gadget: legacy: remove left-over __ref annotations

These were added in commit 780cc0f370 ("usb: gadget: add '__ref' for
rndis_config_register() and cdc_config_register()") to silence
modpost, but they didn't fix the real problem - that was fixed later
by removing wrong __init annotations in commit c94e289f195e ("usb:
gadget: remove incorrect __init/__exit annotations").

It really never makes sense for a function to be marked __ref unless
it (1) has some conditional that chooses whether to call an __init
function (or access __initdata) or not and (2) has a comment
explaining why the __ref is there and why it is safe.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20210323081607.405904-1-linux@rasmusvillemoes.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: u_audio: convert to strscpy

Usage of strlcpy in Linux Kernel has been recently
deprecated [1], convert driver to strscpy

[1] https://lore.kernel.org/lkml/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/

Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1614603943-11668-2-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: f_uac1: disable IN/OUT ep if unused

User can configure f_uac1 function via p_chmask/c_chmask
whether uac1 shall support playback and/or capture,
but it has only effect on the created ALSA device,
but not on the USB descriptor.

This patch adds playback/capture descriptors
dependent on that parameter. It is similar to
the same conversion done earlier for f_uac2

Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1614599375-8803-6-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: f_uac1: validate input parameters

Currently user can configure UAC1 function with
parameters that violate UAC1 spec or are not supported
by UAC1 gadget implementation.

This can lead to incorrect behavior if such gadget
is connected to the host - like enumeration failure
or other issues depending on host's UAC1 driver
implementation, bringing user to a long hours
of debugging the issue.

Instead of silently accept these parameters, throw
an error if they are not valid.

Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1614599375-8803-5-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: f_uac2: validate input parameters

Currently user can configure UAC2 function with
parameters that violate UAC2 spec or are not supported
by UAC2 gadget implementation.

This can lead to incorrect behavior if such gadget
is connected to the host - like enumeration failure
or other issues depending on host's UAC2 driver
implementation, bringing user to a long hours
of debugging the issue.

Instead of silently accept these parameters, throw
an error if they are not valid.

Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1614599375-8803-4-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: legacy: fix error return code of multi_bind()

When usb_otg_descriptor_alloc() returns NULL to usb_desc, no error
return code of multi_bind() is assigned.
To fix this bug, status is assigned with -ENOMEM in this case.

Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20210307084545.21775-1-baijiaju1990@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: f_uac2: adds support for SS and SSP

Patch adds support of SS and SSP speed.

Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20210310105216.38202-1-pawell@gli-login.cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: chipidea: tegra: Silence deferred probe error

Silence deferred probe error caused by the PHY driver which is probed
later than the ChipIdea driver.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314203927.2572-1-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget/function/f_fs string table fix for multiple languages

Fixes bug with the handling of more than one language in
the string table in f_fs.c.
str_count was not reset for subsequent language codes.
str_count-- "rolls under" and processes u32 max strings on
the processing of the second language entry.
The existing bug can be reproduced by adding a second language table
to the structure "strings" in tools/usb/ffs-test.c.

Signed-off-by: Dean Anderson <dean@sensoray.com>
Link: https://lore.kernel.org/r/20210317224109.21534-1-dean@sensoray.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: Add driver for Xilinx platforms

Add a new driver for supporting Xilinx platforms. This driver is used
for some sequence of operations required for Xilinx USB controllers.
This driver is also used to choose between PIPE clock coming from SerDes
and the Suspend Clock. Before the controller is out of reset, the clock
selection should be changed to PIPE clock in order to make the USB
controller work. There is a register added in Xilinx USB controller
register space for the same.

Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1615963949-75320-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: dwc3-xilinx: Add documentation for Versal DWC3 Controller

Add documentation for Versal DWC3 controller. Add required property
'reg' for the same. Also add optional properties for snps,dwc3.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1615963949-75320-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: renesas_usbhs: fix error return code of usbhsf_pkt_handler()

When __usbhsf_pkt_get() returns NULL to pkt, no error return code of
usbhsf_pkt_handler() is assigned.
To fix this bug, ret is assigned with -EINVAL in this case.

Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20210307090030.22369-1-baijiaju1990@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: gadget: Remove invalid low-speed setting

None of the DWC_usb3x IPs (and all their versions) supports low-speed
setting in device mode. In the early days, our "Early Adopter Edition"
DWC_usb3 databook shows that the controller may be configured to operate
in low-speed, but it was revised on release. Let's remove this invalid
speed setting to avoid any confusion.

Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/258b1c7fbb966454f4c4c2c1367508998498fc30.1615509438.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers: usb: host: fotg210-hcd.c: Fix alignment of comment

The * has been aligned on each line for block comment.

Signed-off-by: Shubhankar Kuranagatti <shubhankarvk@gmail.com>
Link: https://lore.kernel.org/r/20210311190901.gaw7m7ndib3uzakm@kewl-virtual-machine
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers: usb: host: fotg210-hcd.c: Fix indentation error

A space was given after tab key. The extra space has been removed.
This is done to maintain uniformity in the code.

Signed-off-by: Shubhankar Kuranagatti <shubhankarvk@gmail.com>
Link: https://lore.kernel.org/r/20210311190058.yudmivcbok56itay@kewl-virtual-machine
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: core: rename usb_driver_claim_interface() data parameter

It's been almost twenty years since the interface "private data" pointer
was removed in favour of using the driver-data pointer of struct device.

Let's rename the driver-data parameter of usb_driver_claim_interface()
so that it better reflects how it's used.

Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210318155406.22399-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: core: drop outdated interface-binding comment

It's been almost twenty years since USB drivers returned a data pointer
from their probe routines in order to bind to an interface.

Time to update the documentation for usb_driver_claim_interface().

Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210318155406.22399-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: sl811-hcd: improve misleading indentation

gcc-11 now warns about a confusingly indented code block:

drivers/usb/host/sl811-hcd.c: In function ‘sl811h_hub_control’:
drivers/usb/host/sl811-hcd.c:1291:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
 1291 |         if (*(u16*)(buf+2))     /* only if wPortChange is interesting */
      |         ^~
drivers/usb/host/sl811-hcd.c:1295:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
 1295 |                 break;

Rewrite this to use a single if() block with the __is_defined() macro.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210322164244.827589-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: ehci: drop workaround for forced irq threading

Force-threaded interrupt handlers used to run with interrupts enabled,
something which could lead to deadlocks in case a threaded handler
shared a lock with code running in hard interrupt context (e.g. timer
callbacks) and did not explicitly disable interrupts.

Since commit 81e2073c175b ("genirq: Disable interrupts for force
threaded handlers") interrupt handlers always run with interrupts
disabled on non-RT so that drivers no longer need to do handle forced
threading ("threadirqs").

Drop the now obsolete workaround added by commit a1227f3c1030 ("usb:
ehci: fix deadlock when threadirqs option is used").

Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322111249.32141-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: host: ehci-tegra: Select USB_GADGET Kconfig option

Select USB_GADGET Kconfig option in order to fix build failure which
happens because ChipIdea driver has a build dependency on both USB_GADGET
and USB_EHCI_HCD, while USB_EHCI_TEGRA force-selects the ChipIdea driver
without taking into account the tristate USB_GADGET dependency. It's not
possible to do anything about the cyclic dependency of the Kconfig
options, but USB_EHCI_TEGRA is now a deprecated option that isn't used
by defconfigs and USB_GADGET is wanted on Tegra by default, hence it's
okay to have a bit clunky workaround for it.

Fixes: c3590c7656fb ("usb: host: ehci-tegra: Remove the driver")
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210320151915.7566-2-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: multi_v7_defconfig: Stop using deprecated USB_EHCI_TEGRA

The USB_EHCI_TEGRA option is deprecated now and replaced by
USB_CHIPIDEA_TEGRA. Replace USB_EHCI_TEGRA with USB_CHIPIDEA_TEGRA
in multi_v7_defconfig.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210320151915.7566-1-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: host: ehci-platform: add spurious_oc DT support

Over-current reporting isn't supported on some platforms such as bcm63xx.
These devices will incorrectly report over-current if this flag isn't properly
activated.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20210223174455.1378-4-noltari@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: generic-ehci: document spurious-oc flag

Over-current reporting isn't supported on some platforms such as bcm63xx.
These devices will incorrectly report over-current if this flag isn't properly
activated.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210223174455.1378-3-noltari@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: ehci: add spurious flag to disable overcurrent checking

This patch adds an ignore_oc flag which can be set by EHCI controller
not supporting or wanting to disable overcurrent checking. The EHCI
platform data in include/linux/usb/ehci_pdriver.h is also augmented to
take advantage of this new flag.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20210223174455.1378-2-noltari@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: fix yamllint check warning

Fix warning: "missing starting space in comment"

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210308053745.25697-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge 5.12-rc4 into usb-next

We need the usb/thunderbolt fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 5.12-rc4

Merge tag 'ext4_for_linus_stable' of git://git./linux/kernel/git/tytso/ext4

Pull ext4 fixes from Ted Ts'o:
 "Miscellaneous ext4 bug fixes for v5.12"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: initialize ret to suppress smatch warning
  ext4: stop inode update before return
  ext4: fix rename whiteout with fast commit
  ext4: fix timer use-after-free on failed mount
  ext4: fix potential error in ext4_do_update_inode
  ext4: do not try to set xattr into ea_inode if value is empty
  ext4: do not iput inode under running transaction in ext4_rename()
  ext4: find old entry again if failed to rename whiteout
  ext4: fix error handling in ext4_end_enable_verity()
  ext4: fix bh ref count on error paths
  fs/ext4: fix integer overflow in s_log_groups_per_flex
  ext4: add reclaim checks to xattr code
  ext4: shrink race window in ext4_should_retry_alloc()

Merge tag 'io_uring-5.12-2021-03-21' of git://git.kernel.dk/linux-block

Pull io_uring followup fixes from Jens Axboe:

 - The SIGSTOP change from Eric, so we properly ignore that for
   PF_IO_WORKER threads.

 - Disallow sending signals to PF_IO_WORKER threads in general, we're
   not interested in having them funnel back to the io_uring owning
   task.

 - Stable fix from Stefan, ensuring we properly break links for short
   send/sendmsg recv/recvmsg if MSG_WAITALL is set.

 - Catch and loop when needing to run task_work before a PF_IO_WORKER
   threads goes to sleep.

* tag 'io_uring-5.12-2021-03-21' of git://git.kernel.dk/linux-block:
  io_uring: call req_set_fail_links() on short send[msg]()/recv[msg]() with MSG_WAITALL
  io-wq: ensure task is running before processing task_work
  signal: don't allow STOP on PF_IO_WORKER threads
  signal: don't allow sending any signals to PF_IO_WORKER threads

Merge tag 'staging-5.12-rc4' of git://git./linux/kernel/git/gregkh/staging

Pull staging and IIO driver fixes from Greg KH:
 "Some small staging and IIO driver fixes:

   - MAINTAINERS changes for the move of the staging mailing list

   - comedi driver fixes to get request_irq() to work correctly

   - counter driver fixes for reported issues with iio devices

   - tiny iio driver fixes for reported issues.

  All of these have been in linux-next with no reported problems"

* tag 'staging-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: vt665x: fix alignment constraints
  staging: comedi: cb_pcidas64: fix request_irq() warn
  staging: comedi: cb_pcidas: fix request_irq() warn
  MAINTAINERS: move the staging subsystem to lists.linux.dev
  MAINTAINERS: move some real subsystems off of the staging mailing list
  iio: gyro: mpu3050: Fix error handling in mpu3050_trigger_handler
  iio: hid-sensor-temperature: Fix issues of timestamp channel
  iio: hid-sensor-humidity: Fix alignment issue of timestamp channel
  counter: stm32-timer-cnt: fix ceiling miss-alignment with reload register
  counter: stm32-timer-cnt: fix ceiling write max value
  counter: stm32-timer-cnt: Report count function when SLAVE_MODE_DISABLED
  iio: adc: ab8500-gpadc: Fix off by 10 to 3
  iio:adc:stm32-adc: Add HAS_IOMEM dependency
  iio: adis16400: Fix an error code in adis16400_initial_setup()
  iio: adc: adi-axi-adc: add proper Kconfig dependencies
  iio: adc: ad7949: fix wrong ADC result due to incorrect bit mask
  iio: hid-sensor-prox: Fix scale not correct issue
  iio:adc:qcom-spmi-vadc: add default scale to LR_MUX2_BAT_ID channel

Merge tag 'usb-5.12-rc4' of git://git./linux/kernel/git/gregkh/usb

Pull USB and Thunderbolt driver fixes from Greg KH:
 "Here are some small Thunderbolt and USB driver fixes for some reported
  issues:

   - thunderbolt fixes for minor problems

   - typec fixes for power issues

   - usb-storage quirk addition

   - usbip bugfix

   - dwc3 bugfix when stopping transfers

   - cdnsp bugfix for isoc transfers

   - gadget use-after-free fix

  All have been in linux-next this week with no reported issues"

* tag 'usb-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: typec: tcpm: Skip sink_cap query only when VDM sm is busy
  usb: dwc3: gadget: Prevent EP queuing while stopping transfers
  usb: typec: tcpm: Invoke power_supply_changed for tcpm-source-psy-
  usb: typec: Remove vdo[3] part of tps6598x_rx_identity_reg struct
  usb-storage: Add quirk to defeat Kindle's automatic unload
  usb: gadget: configfs: Fix KASAN use-after-free
  usbip: Fix incorrect double assignment to udc->ud.tcp_rx
  usb: cdnsp: Fixes incorrect value in ISOC TRB
  thunderbolt: Increase runtime PM reference count on DP tunnel discovery
  thunderbolt: Initialize HopID IDAs in tb_switch_alloc()