OSDN Git Service
Paul M Stillwell Jr [Tue, 2 Mar 2021 18:12:05 +0000 (10:12 -0800)]
ice: handle increasing Tx or Rx ring sizes
There is an issue when the Tx or Rx ring size increases using
'ethtool -L ...' where the new rings don't get the correct ITR
values because when we rebuild the VSI we don't know that some
of the rings may be new.
Fix this by looking at the original number of rings and
determining if the rings in ice_vsi_rebuild_set_coalesce()
were not present in the original rings received in
ice_vsi_rebuild_get_coalesce().
Also change the code to return an error if we can't allocate
memory for the coalesce data in ice_vsi_rebuild().
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Dan Nowlin [Tue, 2 Mar 2021 18:12:04 +0000 (10:12 -0800)]
ice: Update to use package info from ice segment
There are two package versions in the package binary. Today, these two
version numbers are the same. However, in the future that may change.
Update code to use the package info from the ice segment metadata
section, which is the package information that is actually downloaded to
the firmware during the download package process.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Anirudh Venkataramanan [Tue, 2 Mar 2021 18:12:03 +0000 (10:12 -0800)]
ice: Delay netdev registration
Once a netdev is registered, the corresponding network interface can
be immediately used by userspace utilities (like say NetworkManager).
This can be problematic if the driver technically isn't fully up yet.
Move netdev registration to the end of probe, as by this time the
driver data structures and device will be initialized as expected.
However, delaying netdev registration causes a failure in the aRFS flow
where netdev->reg_state == NETREG_REGISTERED condition is checked. It's
not clear why this check was added to begin with, so remove it.
Local testing didn't indicate any issues with this change.
The state bit check in ice_open was put in as a stop-gap measure to
prevent a premature interface up operation. This is no longer needed,
so remove it.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Benita Bose [Tue, 2 Mar 2021 18:12:02 +0000 (10:12 -0800)]
ice: Add Support for XPS
Enable and configure XPS. The driver code implemented sets up the Transmit
Packet Steering Map, which in turn will be used by the kernel in queue
selection during Tx.
Signed-off-by: Benita Bose <benita.bose@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Eric Lin [Wed, 31 Mar 2021 01:04:17 +0000 (09:04 +0800)]
net: ethernet: Fix typo of 'network' in comment
Signed-off-by: Eric Lin <dslin1010@gmail.com>
Reported-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 30 Mar 2021 06:58:41 +0000 (09:58 +0300)]
mlxsw: spectrum_router: Only perform atomic nexthop bucket replacement when requested
When cleared, the 'force' parameter in nexthop bucket replacement
notifications indicates that a driver should try to perform an atomic
replacement. Meaning, only update the contents of the bucket if it is
inactive.
Since mlxsw only queries buckets' activity once every second, there is
no point in trying an atomic replacement if the idle timer interval is
smaller than 1 second.
Currently, mlxsw ignores the original value of 'force' and will always
try an atomic replacement if the idle timer is not smaller than 1
second.
Fix this by taking the original value of 'force' into account and never
promoting a non-atomic replacement to an atomic one.
Fixes:
617a77f044ed ("mlxsw: spectrum_router: Add nexthop bucket replacement support")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 31 Mar 2021 00:42:23 +0000 (17:42 -0700)]
Merge branch 'mptcp-subflow-disconnected'
Mat Martineau says:
====================
MPTCP: Allow initial subflow to be disconnected
An MPTCP connection is aggregated from multiple TCP subflows, and can
involve multiple IP addresses on either peer. The addresses used in the
initial subflow connection are assigned address id 0 on each side of the
link. More addresses can be added and shared with the peer using address
IDs of 1 or larger. MPTCP in Linux shares non-zero address IDs across
all MPTCP connections in a net namespace, which allows userspace to
manage subflow connections across a number of sockets. However, this
makes the address with id 0 a special case, since the IP address
associated with id 0 is potentially different for each socket.
This patch set allows the initial subflow to be disconnected when
userspace specifies an address to remove using both id 0 and an IP
address, or when the peer sends an RM_ADDR for id 0.
Patches 1 and 3 implement the change for requests from the peer and
userspace, respectively.
Patch 2 consolidates some code for disconnecting subflows.
Patches 4-6 update the self tests to cover removal of subflows using
address id 0.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Wed, 31 Mar 2021 00:08:56 +0000 (17:08 -0700)]
selftests: mptcp: remove id 0 address testcases
This patch added the testcases for removing the id 0 subflow and the id 0
address.
In do_transfer, use the removing addresses number '9' for deleting the id
0 address.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Wed, 31 Mar 2021 00:08:55 +0000 (17:08 -0700)]
selftests: mptcp: add addr argument for del_addr
For the id 0 address, different MPTCP connections could be using
different IP addresses for id 0.
This patch added an extra argument IP address for del_addr when
using id 0.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthieu Baerts [Wed, 31 Mar 2021 00:08:54 +0000 (17:08 -0700)]
selftests: mptcp: avoid calling pm_nl_ctl with bad IDs
IDs are supposed to be between 0 and 255.
In pm_nl_ctl, for both the 'add' and 'get' instruction, the ID is casted
in a u_int8_t. So if we give 256, we will delete ID 0. Obviously, the
goal is not to delete this ID by giving 256.
We could modify pm_nl_ctl and stop if the ID is negative or higher than
255 but probably better not to increase the number of lines for such
things in this tool which is only used in selftests. Instead, we use it
within the limits.
This modification also means that we will no longer add a new ID for the
2nd entry. That's why we removed an expected entry from the dump and
introduced with
commit
dc8eb10e95a8 ("selftests: mptcp: add testcases for setting the address ID").
So now we delete ID 9 like before and we add entries for IDs 10 to 255
that are deleted just after.
Note that this could be seen as a fix but it was not really an issue so
far: we were simply playing with ID 0/1 once again. With the following
commit ("selftests: mptcp: add addr argument for del_addr"), it will be
different because ID 0 is going to required an address. We don't want
errors when trying to delete ID 0 without the address argument.
Acked-and-tested-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Wed, 31 Mar 2021 00:08:53 +0000 (17:08 -0700)]
mptcp: remove id 0 address
This patch added a new function mptcp_nl_remove_id_zero_address to
remove the id 0 address.
In this function, traverse all the existing msk sockets to find the
msk matched the input IP address. Then fill the removing list with
id 0, and pass it to mptcp_pm_remove_addr and mptcp_pm_remove_subflow.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Suggested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Wed, 31 Mar 2021 00:08:52 +0000 (17:08 -0700)]
mptcp: unify RM_ADDR and RM_SUBFLOW receiving
There are some duplicate code in mptcp_pm_nl_rm_addr_received and
mptcp_pm_nl_rm_subflow_received. This patch unifies them into a new
function named mptcp_pm_nl_rm_addr_or_subflow. In it, use the input
parameter rm_type to identify it's now removing an address or a subflow.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Wed, 31 Mar 2021 00:08:51 +0000 (17:08 -0700)]
mptcp: remove all subflows involving id 0 address
There's only one subflow involving the non-zero id address, but there
may be multi subflows involving the id 0 address.
Here's an example:
local_id=0, remote_id=0
local_id=1, remote_id=0
local_id=0, remote_id=1
If the removing address id is 0, all the subflows involving the id 0
address need to be removed.
In mptcp_pm_nl_rm_addr_received/mptcp_pm_nl_rm_subflow_received, the
"break" prevents the iteration to the next subflow, so this patch
dropped them.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 30 Mar 2021 21:06:13 +0000 (14:06 -0700)]
net: fix icmp_echo_enable_probe sysctl
sysctl_icmp_echo_enable_probe is an u8.
ipv4_net_table entry should use
.maxlen = sizeof(u8).
.proc_handler = proc_dou8vec_minmax,
Fixes:
f1b8fa9fa586 ("net: add sysctl for enabling RFC 8335 PROBE messages")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 31 Mar 2021 00:37:13 +0000 (17:37 -0700)]
Merge branch 'ionic-cleanups'
Shannon Nelson says:
====================
ionic: code cleanup for heartbeat, dma error counts, sizeof, stats
These patches are a few more bits of code cleanup found in
testing and review: count all our dma error instances, make
better use of sizeof, fix a race in our device heartbeat check,
and clean up code formatting in the ethtool stats collection.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Tue, 30 Mar 2021 19:52:10 +0000 (12:52 -0700)]
ionic: pull per-q stats work out of queue loops
Abstract out the per-queue data collection work into separate
functions from the per-queue loops in the stats reporting,
similar to what Alex did for the data label strings in
commit
acebe5b6107c ("ionic: Update driver to use ethtool_sprintf")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Tue, 30 Mar 2021 19:52:09 +0000 (12:52 -0700)]
ionic: avoid races in ionic_heartbeat_check
Rework the heartbeat checks to be sure that we're getting an
atomic operation. Through testing we found occasions where a
separate thread could clash with this check and cause erroneous
heartbeat check results.
Signed-off-by: Allen Hubbe <allenbh@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Tue, 30 Mar 2021 19:52:08 +0000 (12:52 -0700)]
ionic: fix sizeof usage
Use the actual pointer that we care about as the subject of the
sizeof, rather than a struct name.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Tue, 30 Mar 2021 19:52:07 +0000 (12:52 -0700)]
ionic: count dma errors
Increment our dma-error counter in a couple of spots
that were missed before.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 31 Mar 2021 00:18:26 +0000 (17:18 -0700)]
Merge branch 'dpaa2-switch-STP'
Ioana Ciornei says:
====================
dpaa2-switch: add STP support
This patch set adds support for STP to the dpaa2-switch.
First of all, it fixes a bug which was determined by the improper usage
of bridge BR_STATE_* values directly in the MC ABI.
The next patches deal with creating an ACL table per port and trapping
the STP frames to the control interface by adding an entry into each
table.
The last patch configures proper learning state depending on the STP
state.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Tue, 30 Mar 2021 14:54:19 +0000 (17:54 +0300)]
dpaa2-switch: setup learning state on STP state change
Depending on what STP state a port is in, the learning on that port
should be enabled or disabled.
When the STP state is DISABLED, BLOCKING or LISTENING no learning should
be happening irrespective of what the bridge previously requested. The
learning state is changed to be the one setup by the bridge when the STP
state is LEARNING or FORWARDING.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Tue, 30 Mar 2021 14:54:18 +0000 (17:54 +0300)]
dpaa2-switch: trap STP frames to the CPU
Add an ACL entry in each port's ACL table to redirect any frame that
has the destination MAC address equal to the STP dmac to the control
interface.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Tue, 30 Mar 2021 14:54:17 +0000 (17:54 +0300)]
dpaa2-switch: keep track of the current learning state per port
Keep track of the current learning state per port so that we can
reference it in the next patches when setting up a STP state.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Tue, 30 Mar 2021 14:54:16 +0000 (17:54 +0300)]
dpaa2-switch: create and assign an ACL table per port
In order to trap frames to the CPU, the DPAA2 switch uses the ACL table.
At probe time, create an ACL table for each switch port so that in the
next patches we can use this to trap STP frames and redirect them to the
control interface.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Tue, 30 Mar 2021 14:54:15 +0000 (17:54 +0300)]
dpaa2-switch: fix the translation between the bridge and dpsw STP states
The numerical values used for STP states are different between the
bridge and the MC ABI therefore, the direct usage of the
BR_STATE_* macros directly in the structures passed to the firmware is
incorrect.
Create a separate function that translates between the bridge STP states
and the enum that holds the STP state as seen by the Management Complex.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov [Tue, 30 Mar 2021 10:41:10 +0000 (13:41 +0300)]
tc-testing: add simple action change test
Use act_simple to verify that action created with 'tc actions change'
command exists after command returns. The goal is to verify internal action
API reference counting to ensure that the case when netlink message has
NLM_F_REPLACE flag set but action with specified index doesn't exist is
handled correctly.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 31 Mar 2021 00:06:50 +0000 (17:06 -0700)]
Merge branch 'udp-gro-L4'
Paolo Abeni says:
====================
udp: GRO L4 improvements
This series improves the UDP L4 - either 'forward' or 'frag_list' -
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic.
The first for patches are mostly bugfixes, addressing some GRO
edge-cases when both tunnels and L4 are present, enabled and in use.
The next 3 patches avoid unneeded segmentation when UDP GRO
traffic traverses in the receive path UDP tunnels.
Finally, some self-tests are included, covering the relevant
GRO scenarios.
Even if most patches are actually bugfixes, this series is
targeting net-next, as overall it makes available a new feature.
v2 -> v3:
- no code changes, more verbose commit messages and comment in
patch 1/8
v1 -> v2:
- restrict post segmentation csum fixup to the only the relevant pkts
- use individual 'accept_gso_type' fields instead of whole gso bitmask
(Willem)
- use only ipv6 addesses from test range in self-tests (Willem)
- hopefully clarified most individual patches commit messages
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 30 Mar 2021 10:28:56 +0000 (12:28 +0200)]
selftests: net: add UDP GRO forwarding self-tests
Create a bunch of virtual topologies and verify that
NETIF_F_GRO_FRAGLIST or NETIF_F_GRO_UDP_FWD-enabled
devices aggregate the ingress packets as expected.
Additionally check that the aggregate packets are
segmented correctly when landing on a socket
Also test SKB_GSO_FRAGLIST and SKB_GSO_UDP_L4 aggregation
on top of UDP tunnel (vxlan)
v1 -> v2:
- hopefully clarify the commit message
- moved the overlay network ipv6 range into the 'documentation'
reserved range (Willem)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 30 Mar 2021 10:28:55 +0000 (12:28 +0200)]
bareudp: allow UDP L4 GRO passthrou
Similar to the previous commit, let even geneve
passthrou the L4 GRO packets
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 30 Mar 2021 10:28:54 +0000 (12:28 +0200)]
geneve: allow UDP L4 GRO passthrou
Similar to the previous commit, let even geneve
passthrou the L4 GRO packets
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 30 Mar 2021 10:28:53 +0000 (12:28 +0200)]
vxlan: allow L4 GRO passthrough
When passing up an UDP GSO packet with L4 aggregation, there is
no need to segment it at the vxlan level. We can propagate the
packet untouched and let it be segmented later, if needed.
Introduce an helper to allow let the UDP socket to accept any
L4 aggregation and use it in the vxlan driver.
v1 -> v2:
- updated to use the newly introduced UDP socket 'accept*' fields
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 30 Mar 2021 10:28:52 +0000 (12:28 +0200)]
udp: never accept GSO_FRAGLIST packets
Currently the UDP protocol delivers GSO_FRAGLIST packets to
the sockets without the expected segmentation.
This change addresses the issue introducing and maintaining
a couple of new fields to explicitly accept SKB_GSO_UDP_L4
or GSO_FRAGLIST packets. Additionally updates udp_unexpected_gso()
accordingly.
UDP sockets enabling UDP_GRO stil keep accept_udp_fraglist
zeroed.
v1 -> v2:
- use 2 bits instead of a whole GSO bitmask (Willem)
Fixes:
9fd1ff5d2ac7 ("udp: Support UDP fraglist GRO/GSO.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 30 Mar 2021 10:28:51 +0000 (12:28 +0200)]
udp: properly complete L4 GRO over UDP tunnel packet
After the previous patch, the stack can do L4 UDP aggregation
on top of a UDP tunnel.
In such scenario, udp{4,6}_gro_complete will be called twice. This function
will enter its is_flist branch immediately, even though that is only
correct on the second call, as GSO_FRAGLIST is only relevant for the
inner packet.
Instead, we need to try first UDP tunnel-based aggregation, if the GRO
packet requires that.
This patch changes udp{4,6}_gro_complete to skip the frag list processing
when while encap_mark == 1, identifying processing of the outer tunnel
header.
Additionally, clears the field in udp_gro_complete() so that we can enter
the frag list path on the next round, for the inner header.
v1 -> v2:
- hopefully clarified the commit message
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 30 Mar 2021 10:28:50 +0000 (12:28 +0200)]
udp: skip L4 aggregation for UDP tunnel packets
If NETIF_F_GRO_FRAGLIST or NETIF_F_GRO_UDP_FWD are enabled, and there
are UDP tunnels available in the system, udp_gro_receive() could end-up
doing L4 aggregation (either SKB_GSO_UDP_L4 or SKB_GSO_FRAGLIST) at
the outer UDP tunnel level for packets effectively carrying and UDP
tunnel header.
That could cause inner protocol corruption. If e.g. the relevant
packets carry a vxlan header, different vxlan ids will be ignored/
aggregated to the same GSO packet. Inner headers will be ignored, too,
so that e.g. TCP over vxlan push packets will be held in the GRO
engine till the next flush, etc.
Just skip the SKB_GSO_UDP_L4 and SKB_GSO_FRAGLIST code path if the
current packet could land in a UDP tunnel, and let udp_gro_receive()
do GRO via udp_sk(sk)->gro_receive.
The check implemented in this patch is broader than what is strictly
needed, as the existing UDP tunnel could be e.g. configured on top of
a different device: we could end-up skipping GRO at-all for some packets.
Anyhow, that is a very thin corner case and covering it will add quite
a bit of complexity.
v1 -> v2:
- hopefully clarify the commit message
Fixes:
9fd1ff5d2ac7 ("udp: Support UDP fraglist GRO/GSO.")
Fixes:
36707061d6ba ("udp: allow forwarding of plain (non-fraglisted) UDP GRO packets")
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 30 Mar 2021 10:28:49 +0000 (12:28 +0200)]
udp: fixup csum for GSO receive slow path
When UDP packets generated locally by a socket with UDP_SEGMENT
traverse the following path:
UDP tunnel(xmit) -> veth (segmentation) -> veth (gro) ->
UDP tunnel (rx) -> UDP socket (no UDP_GRO)
ip_summed will be set to CHECKSUM_PARTIAL at creation time and
such checksum mode will be preserved in the above path up to the
UDP tunnel receive code where we have:
__iptunnel_pull_header() -> skb_pull_rcsum() ->
skb_postpull_rcsum() -> __skb_postpull_rcsum()
The latter will convert the skb to CHECKSUM_NONE.
The UDP GSO packet will be later segmented as part of the rx socket
receive operation, and will present a CHECKSUM_NONE after segmentation.
Additionally the segmented packets UDP CB still refers to the original
GSO packet len. Overall that causes unexpected/wrong csum validation
errors later in the UDP receive path.
We could possibly address the issue with some additional checks and
csum mangling in the UDP tunnel code. Since the issue affects only
this UDP receive slow path, let's set a suitable csum status there.
Note that SKB_GSO_UDP_L4 or SKB_GSO_FRAGLIST packets lacking an UDP
encapsulation present a valid checksum when landing to udp_queue_rcv_skb(),
as the UDP checksum has been validated by the GRO engine.
v2 -> v3:
- even more verbose commit message and comments
v1 -> v2:
- restrict the csum update to the packets strictly needing them
- hopefully clarify the commit message and code comments
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiapeng Chong [Tue, 30 Mar 2021 09:51:30 +0000 (17:51 +0800)]
ppp: deflate: Remove useless call "zlib_inflateEnd"
Fix the following whitescan warning:
Calling "zlib_inflateEnd(&state->strm)" is only useful for its return
value, which is ignored.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 30 Mar 2021 23:56:40 +0000 (16:56 -0700)]
Merge branch 'net-repeated-words'
Huazhong Tan says:
====================
net: remove repeated words
This patch-set removes some repeated words in comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Tue, 30 Mar 2021 07:27:56 +0000 (15:27 +0800)]
net: ipa: remove repeated words
Remove repeated words "that" and "the".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Tue, 30 Mar 2021 07:27:55 +0000 (15:27 +0800)]
net: phy: remove repeated word
Remove repeated word "to".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Tue, 30 Mar 2021 07:27:54 +0000 (15:27 +0800)]
net: bonding: remove repeated word
Remove repeated word "that".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Tue, 30 Mar 2021 07:27:53 +0000 (15:27 +0800)]
net: i40e: remove repeated words
Remove repeated words "to" and "try".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 30 Mar 2021 23:54:50 +0000 (16:54 -0700)]
Merge branch 'obsdolete-todo'
Wang Qing says:
====================
Clean up obsolete TODO files
It is mentioned in the official documents of the Linux Foundation and WIKI
that you can participate in its development according to the TODO files of
each module.
But the TODO files here has not been updated for 15 years, and the function
development described in the file have been implemented or abandoned.
Its existence will mislead developers seeking to view outdated information.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Qing [Tue, 30 Mar 2021 07:02:49 +0000 (15:02 +0800)]
net/decnet: Delete obsolete TODO file
The TODO file here has not been updated from 2005, and the function
development described in the file have been implemented or abandoned.
Its existence will mislead developers seeking to view outdated information.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Qing [Tue, 30 Mar 2021 07:02:48 +0000 (15:02 +0800)]
net/ax25: Delete obsolete TODO file
The TODO file here has not been updated for 13 years, and the function
development described in the file have been implemented or abandoned.
Its existence will mislead developers seeking to view outdated information.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Qing [Tue, 30 Mar 2021 07:02:47 +0000 (15:02 +0800)]
fs/jffs2: Delete obsolete TODO file
The TODO file here has not been updated for 14 years, and the function
development described in the file have been implemented or abandoned.
Its existence will mislead developers seeking to view outdated information.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Qing [Tue, 30 Mar 2021 07:02:46 +0000 (15:02 +0800)]
fs/befs: Delete obsolete TODO file
The TODO file here has not been updated from 2005, and the function
development described in the file have been implemented or abandoned.
Its existence will mislead developers seeking to view outdated information.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Qing [Tue, 30 Mar 2021 07:02:45 +0000 (15:02 +0800)]
scsi/aacraid: Delete obsolete TODO file
The TODO file here has not been updated from 2.6.12 for more than 15 years.
Its existence will mislead developers seeking to view outdated information.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Qing [Tue, 30 Mar 2021 07:02:44 +0000 (15:02 +0800)]
mips/sgi-ip27: Delete obsolete TODO file
The TODO file here has not been updated for 15 years, and the function
development described in the file have been implemented or abandoned.
Its existence will mislead developers seeking to view outdated information.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Yingliang [Tue, 30 Mar 2021 12:55:39 +0000 (20:55 +0800)]
net: mhi: remove pointless conditional before kfree_skb()
It already has null pointer check in kfree_skb(),
remove pointless pointer check before kfree_skb().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wong Vee Khee [Tue, 30 Mar 2021 02:46:53 +0000 (10:46 +0800)]
stmmac: intel: add cross time-stamping freq difference adjustment
Cross time-stamping mechanism used in certain instance of Intel mGbE
may run at different clock frequency in comparison to the clock
frequency used by processor, so we introduce cross T/S frequency
adjustment to ensure TSC calculation is correct when processor got the
cross time-stamps.
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shixin Liu [Tue, 30 Mar 2021 02:24:15 +0000 (10:24 +0800)]
mISDN: Use LIST_HEAD() for list_head
There's no need to declare a list and then init it manually,
just use the LIST_HEAD() macro.
Signed-off-by: Shixin Liu <liushixin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shixin Liu [Tue, 30 Mar 2021 02:24:14 +0000 (10:24 +0800)]
mISDN: Use DEFINE_SPINLOCK() for spinlock
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Changelog:
From v1:
1. fix the mistake reported by kernel test robot.
Signed-off-by: Shixin Liu <liushixin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 30 Mar 2021 20:29:39 +0000 (13:29 -0700)]
Merge branch 'rfc8335-probe'
Andreas Roeseler says:
====================
add support for RFC 8335 PROBE
The popular utility ping has several severe limitations, such as the
inability to query specific interfaces on a node and requiring
bidirectional connectivity between the probing and probed interfaces.
RFC 8335 attempts to solve these limitations by creating the new utility
PROBE which is a specialized ICMP message that makes use of the ICMP
Extension Structure outlined in RFC 4884.
This patchset adds definitions for the ICMP Extended Echo Request and
Reply (PROBE) types for both IPV4 and IPV6, adds a sysctl to enable
responses to PROBE messages, expands the list of supported ICMP messages
to accommodate PROBE types, adds ipv6_dev_find into ipv6_stubs, and adds
functionality to respond to PROBE requests.
Changes:
v1 -> v2:
- Add AFI definitions
- Switch to functions such as dev_get_by_name and ip_dev_find to lookup
net devices
v2 -> v3:
Suggested by Willem de Bruijn <willemdebruijn.kernel@gmail.com>
- Add verification of incoming messages before looking up netdev
- Add prefix for PROBE specific defined variables
- Use proc_dointvec_minmax with zero and one for sysctl
- Create struct icmp_ext_echo_iio for parsing incoming packets
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
- Include net/addrconf.h library for ipv6_dev_find
v3 -> v4:
- Use in_addr instead of __be32 for storing IPV4 addresses
- Use IFNAMSIZ to statically allocate space for name in
icmp_ext_echo_iio
Suggested by Willem de Bruijn <willemdebruijn.kernel@gmail.com>
- Use skb_header_pointer to verify fields in incoming message
- Add check to ensure that extobj_hdr.length is valid
- Check to ensure object payload is padded with ASCII NULL characters
when probing by name, as specified by RFC 8335
- Statically allocate buff using IFNAMSIZ
- Add rcu blocking around ipv6_dev_find
- Use __in_dev_get_rcu to access IPV4 addresses of identified
net_device
- Remove check for ICMPV6 PROBE types
v4 -> v5:
- Statically allocate buff to size IFNAMSIZ on declaration
- Remove goto probe in favor of single branch
- Remove strict check for incoming PROBE request padding to nearest
32-bit boundary
Reported-by: kernel test robot <lkp@intel.com>
v5 -> v6:
- Add documentation for icmp_echo_enable_probe sysctl
- Remove RCU locking around ipv6_dev_find()
- Assign iio based on ctype
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Roeseler [Tue, 30 Mar 2021 01:45:51 +0000 (18:45 -0700)]
icmp: add response to RFC 8335 PROBE messages
Modify the icmp_rcv function to check PROBE messages and call icmp_echo
if a PROBE request is detected.
Modify the existing icmp_echo function to respond ot both ping and PROBE
requests.
This was tested using a custom modification to the iputils package and
wireshark. It supports IPV4 probing by name, ifindex, and probing by
both IPV4 and IPV6 addresses. It currently does not support responding
to probes off the proxy node (see RFC 8335 Section 2).
The modification to the iputils package is still in development and can
be found here: https://github.com/Juniper-Clinic-2020/iputils.git. It
supports full sending functionality of PROBE requests, but currently
does not parse the response messages, which is why Wireshark is required
to verify the sent and recieved PROBE messages. The modification adds
the ``-e'' flag to the command which allows the user to specify the
interface identifier to query the probed host. An example usage would be
<./ping -4 -e 1 [destination]> to send a PROBE request of ifindex 1 to the
destination node.
Signed-off-by: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Roeseler [Tue, 30 Mar 2021 01:45:43 +0000 (18:45 -0700)]
ipv6: add ipv6_dev_find to stubs
Add ipv6_dev_find to ipv6_stub to allow lookup of net_devices by IPV6
address in net/ipv4/icmp.c.
Signed-off-by: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Roeseler [Tue, 30 Mar 2021 01:45:36 +0000 (18:45 -0700)]
net: add support for sending RFC 8335 PROBE messages
Modify the ping_supported function to support PROBE message types. This
allows tools such as the ping command in the iputils package to be
modified to send PROBE requests through the existing framework for
sending ping requests.
Signed-off-by: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Roeseler [Tue, 30 Mar 2021 01:45:29 +0000 (18:45 -0700)]
net: add sysctl for enabling RFC 8335 PROBE messages
Section 8 of RFC 8335 specifies potential security concerns of
responding to PROBE requests, and states that nodes that support PROBE
functionality MUST be able to enable/disable responses and that
responses MUST be disabled by default
Signed-off-by: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Roeseler [Tue, 30 Mar 2021 01:45:21 +0000 (18:45 -0700)]
ICMPV6: add support for RFC 8335 PROBE
Add definitions for the ICMPV6 type of Extended Echo Request and
Extended Echo Reply, as defined by sections 2 and 3 of RFC 8335.
Signed-off-by: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Roeseler [Tue, 30 Mar 2021 01:45:15 +0000 (18:45 -0700)]
icmp: add support for RFC 8335 PROBE
Add definitions for PROBE ICMP types and codes.
Add AFI definitions for IP and IPV6 as specified by IANA
Add a struct to represent the additional header when probing by IP
address (ctype == 3) for use in parsing incoming PROBE messages
Add a struct to represent the entire Interface Identification Object
(IIO) section of an incoming PROBE packet
Signed-off-by: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Edich [Mon, 29 Mar 2021 09:45:36 +0000 (11:45 +0200)]
net: phy: lan87xx: fix access to wrong register of LAN87xx
The function lan87xx_config_aneg_ext was introduced to configure
LAN95xxA but as well writes to undocumented register of LAN87xx.
This fix prevents that access.
The function lan87xx_config_aneg_ext gets more suitable for the new
behavior name.
Reported-by: Måns Rullgård <mans@mansr.com>
Fixes:
05b35e7eb9a1 ("smsc95xx: add phylib support")
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 30 Mar 2021 20:04:28 +0000 (13:04 -0700)]
Merge tag 'linux-can-next-for-5.13-
20210330' of git://git./linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2021-03-30
this is a pull request of 39 patches for net-next/master.
The first two patches update the MAINTAINERS file. One is by me and
removes Dan Murphy from the from m_can and tcan4x5x. The other one is
by Pankaj Sharma and updates the maintainership of the m-can mmio
driver.
The next three patches are by me and update the CAN echo skb handling.
Vincent Mailhol provides 5 patches where Transmitter Delay
Compensation is added CAN bittiming calculation is cleaned up.
The next patch is by me and adds a missing HAS_IOMEM to the grcan
driver.
Michal Simek's patch for the xilinx driver add dev_err_probe()
support.
Arnd Bergmann's patch for the ucan driver fixes a compiler warning.
Stephane Grosjean provides 3 patches for the peak USB drivers, which
add ethtool set_phys_id and CAN one-shot mode.
Xulin Sun's patch removes a not needed return check in the m-can
driver. Torin Cooper-Bennun provides 3 patches for the m-can driver
that add rx-offload support to ensure that skbs are sent from softirq
context. Wan Jiabing's patch for the tcan4x5x driver removes a
duplicate include.
The next 6 patches are by me and target the mcp251xfd driver. They add
devcoredump support, simplify the UINC handling, and add HW timestamp
support.
The remaining 12 patches target the c_can driver. The first 6 are by
me and do generic checkpatch related cleanup work. Dario Binacchi's
patches bring some cleanups and increase the number of usable message
objects from 16 to 64.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 30 Mar 2021 19:59:25 +0000 (12:59 -0700)]
Merge tag 'mlx5-updates-2021-03-29' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-03-29
Coexistence of CQE compression and HW PTP time-stamp:
From Aya this series improves mlx5 netdev driver to allow
both mlx5 CQE compression (RX descriptor compression, that saves on PCI
transaction) and HW time-stamp PTP to co-exists.
Prior to this series both features were mutually exclusive due to the
nature of CQE compression which reduces the size of RX descriptor for
the price of trimming some data, such as the time-stamp.
In order to allow CQE compression when PTP time stamping is enabled,
We enable it on the regular performance critical RX queues which will
service all the data path traffic that is not PTP.
PTP traffic will be re-directed to dedicated RX queues on which we will
not enable CQE compression and thus keep the time-stamp intact.
Having both features is critical for systems with low PCI BW, e.g.
Multi-Host.
The series will be adding:
1) Infrastructure to create a dedicated RX queue to service the PTP traffic
2) Flow steering plumbing to capture PTP traffic both UDP packets with
destination port 319 and L2 packets with ethertype 0x88F7
3) Steer PTP traffic to the dedicated RX queue.
4) The feature will be enabled when PTP is being configured via the
already existing PTP IOCTL when CQE compression is active, otherwise
no change to the driver flow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dario Binacchi [Tue, 2 Mar 2021 21:54:35 +0000 (22:54 +0100)]
can: c_can: add support to 64 message objects
D_CAN controller supports 16, 32, 64 or 128 message objects, comparing
to 32 on C_CAN. AM335x/AM437x Sitara processors and DRA7 SOC all
instantiate a D_CAN controller with 64 message objects, as described
in the "DCAN features" subsection of the CAN chapter of their
technical reference manuals.
The driver policy has been kept unchanged, and as in the previous
version, the first half of the message objects is used for reception
and the second for transmission.
The I/O load is increased only in the case of 64 message objects,
keeping it unchanged in the case of 32. Two 32-bit read accesses are
in fact required, which however remained at 16-bit for configurations
with 32 message objects.
Link: https://lore.kernel.org/r/20210302215435.18286-7-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Dario Binacchi [Tue, 2 Mar 2021 21:54:34 +0000 (22:54 +0100)]
can: c_can: prepare to up the message objects number
As pointed by commit
c0a9f4d396c9 ("can: c_can: Reduce register
access") the "driver casts the 16 message objects in stone, which is
completely braindead as contemporary hardware has up to 128 message
objects".
The patch prepares the module to extend the number of message objects
beyond the 32 currently managed. This was achieved by transforming the
constants used to manage RX/TX messages into variables without
changing the driver policy.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20210302215435.18286-6-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Dario Binacchi [Tue, 2 Mar 2021 21:54:33 +0000 (22:54 +0100)]
can: c_can: use 32-bit write to set arbitration register
The arbitration register is already set up with 32-bit writes in the
other parts of the code except for this point.
Link: https://lore.kernel.org/r/20210302215435.18286-5-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Dario Binacchi [Tue, 2 Mar 2021 21:54:32 +0000 (22:54 +0100)]
can: c_can: add a comment about IF_RX interface's use
After reading the commit
640916db2bf7 ("can: c_can: Make it SMP safe")
it may sound strange to see the IF_RX interface used by the
can_inval_tx_object function. A comment was added to avoid any
misunderstanding.
Link: https://lore.kernel.org/r/20210302215435.18286-4-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Dario Binacchi [Tue, 2 Mar 2021 21:54:31 +0000 (22:54 +0100)]
can: c_can: fix indentation
Commit
524369e2391f ("can: c_can: remove obsolete STRICT_FRAME_ORDERING Kconfig option")
left behind wrong indentation, fix it.
Link: https://lore.kernel.org/r/20210302215435.18286-3-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Dario Binacchi [Tue, 2 Mar 2021 21:54:30 +0000 (22:54 +0100)]
can: c_can: remove unused code
Commit
9d23a9818cb1 ("can: c_can: Remove unused inline function") left
behind C_CAN_MSG_OBJ_TX_LAST constant.
Commit
fa39b54ccf28 ("can: c_can: Get rid of pointless interrupts") left
behind C_CAN_MSG_RX_LOW_LAST and C_CAN_MSG_OBJ_RX_SPLIT constants.
The removed code also made a comment useless and misleading.
Link: https://lore.kernel.org/r/20210302215435.18286-2-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Thu, 4 Mar 2021 14:23:19 +0000 (15:23 +0100)]
can: c_can: fix remaining checkpatch warnings
This patch fixes the remaining checkpatch warnings in the driver.
Link: https://lore.kernel.org/r/20210304154240.2747987-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Thu, 4 Mar 2021 14:21:36 +0000 (15:21 +0100)]
can: c_can: replace double assignments by two single ones
This patch replaces the double assignments by two single ones, to make
checkpatch happy.
Link: https://lore.kernel.org/r/20210304154240.2747987-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Thu, 4 Mar 2021 14:20:31 +0000 (15:20 +0100)]
can: c_can: fix print formating string
This patch fixes the print format string in the driver, so that it
stays in a single line.
Link: https://lore.kernel.org/r/20210304154240.2747987-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Thu, 4 Mar 2021 14:16:14 +0000 (15:16 +0100)]
can: c_can: fix indention
This patch fixes the indention in the driver.
Link: https://lore.kernel.org/r/20210304154240.2747987-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Thu, 4 Mar 2021 14:16:14 +0000 (15:16 +0100)]
can: c_can: remove unnecessary blank lines and add suggested ones
This patch removes unnecessary blank lines and add suggested ones, so
that checkpatch doesn't complain anymore.
Link: https://lore.kernel.org/r/20210304154240.2747987-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Thu, 4 Mar 2021 14:16:14 +0000 (15:16 +0100)]
can: c_can: convert block comments to network style comments
This patch converts all block comments to network subsystem style
block comments.
Link: https://lore.kernel.org/r/20210304154240.2747987-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 2 Mar 2021 14:58:18 +0000 (15:58 +0100)]
can: mcp251xfd: add HW timestamp to RX, TX and error CAN frames
This patch uses the previously added mcp251xfd_skb_set_timestamp()
function to convert the timestamp done by the CAN controller into a
proper skb hw timestamp.
Link: https://lore.kernel.org/r/20210304161209.2754463-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 2 Mar 2021 14:58:18 +0000 (15:58 +0100)]
can: mcp251xfd: add HW timestamp infrastructure
This patch add the HW timestamping infrastructure. The mcp251xfd has a
free running timer of 32 bit width, running at max 40MHz, which wraps
around every 107 seconds. The current timestamp is latched into RX and
TEF objects automatically be the CAN controller.
This patch sets up a cyclecounter, timecounter and delayed worker
infrastructure (which runs every 45 seconds) to convert the timer into
a proper 64 bit based ns timestamp.
Link: https://lore.kernel.org/r/20210304160328.2752293-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 3 Mar 2021 10:43:41 +0000 (11:43 +0100)]
can: mcp251xfd: mcp251xfd_get_timestamp(): move to mcp251xfd.h
This is a preparation patch, it moves the mcp251xfd_get_timestamp()
function into the mcp251xfd.h file.
Link: https://lore.kernel.org/r/20210304160328.2752293-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 2 Mar 2021 15:46:52 +0000 (16:46 +0100)]
can: mcp251xfd: move netdevice.h to mcp251xfd.h
The netdevice.h header is needed in mcp251xfd.h, so that it can be
included without further headers.
Link: https://lore.kernel.org/r/20210304160328.2752293-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Sat, 13 Feb 2021 23:25:45 +0000 (00:25 +0100)]
can: mcp251xfd: simplify UINC handling
In the patches:
|
1f652bb6bae7 can: mcp25xxfd: rx-path: reduce number of SPI core requests to set UINC bit
|
68c0c1c7f966 can: mcp251xfd: tef-path: reduce number of SPI core requests to set UINC bit
the setting of the UINC bit in the TEF and RX FIFO was batched into a
single SPI message consisting of several transfers. All transfers but
the last need to have the cs_change set to 1.
In the original patches the array of prepared transfers is send from
the beginning with the length depending on the number of read TEF/RX
objects. The cs_change of the last transfer is temporarily set to
0 during send.
This patch removes the modification of cs_change by preparing the last
transfer with cs_change to 0 and all other to 1. When sending the SPI
message the driver now starts with an offset into the array, so that
it always ends on the last entry in the array, which has the cs_change
set to 0.
Link: https://lore.kernel.org/r/20210304160328.2752293-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 23 Dec 2020 15:50:25 +0000 (16:50 +0100)]
can: mcp251xfd: add dev coredump support
For easier debugging this patch adds dev coredump support to the
driver. A dev coredump is generated in case the chip fails to start or
an error in the interrupt handler is detected.
The dev coredump consists of all chip registers and chip memory, as
well as the driver's internal state of the TEF-, RX- and TX-FIFOs, it
can be analyzed with the mcp251xfd-dump tool of the can-utils:
https://github.com/linux-can/can-utils/tree/master/mcp251xfd
Link: https://lore.kernel.org/r/20210304160328.2752293-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Wan Jiabing [Tue, 23 Mar 2021 02:10:25 +0000 (10:10 +0800)]
can: tcan4x5x: remove duplicate include of regmap.h
linux/regmap.h has been included at line 13, so remove the duplicate
one at line 14.
Fixes:
67def4ef8bb9 ("can: tcan4x5x: move regmap code into seperate file")
Link: https://lore.kernel.org/r/20210323021026.140460-1-wanjiabing@vivo.com
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Torin Cooper-Bennun [Mon, 8 Mar 2021 10:24:28 +0000 (10:24 +0000)]
can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context
For peripheral devices, m_can sent skbs directly from a threaded irq
instead of from a softirq context, breaking the tcan4x5x peripheral
driver completely. This patch transitions the driver to use the
rx-offload helper for peripherals, ensuring the skbs are sent from the
correct context, with h/w timestamping to ensure correct ordering.
Link: https://lore.kernel.org/r/20210308102427.63916-4-torin@maxiluxsystems.com
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
[mkl: m_can_class_register(): update error handling]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Torin Cooper-Bennun [Mon, 8 Mar 2021 10:24:27 +0000 (10:24 +0000)]
can: m_can: m_can_chip_config(): enable and configure internal timestamps
This is a prerequisite for transitioning the m_can driver to rx-offload,
which works best with TX and RX timestamps.
The timestamps provided by M_CAN are 16-bit, timed according to the
nominal bit timing, and may be prescaled by a multiplier up to 16. We
choose the highest prescalar so that the timestamp wraps every 2^20 bit
times, or 209 ms at a bus speed of 5 Mbit/s. Timestamps will have a
precision of 16 bit times.
Link: https://lore.kernel.org/r/20210308102427.63916-3-torin@maxiluxsystems.com
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Torin Cooper-Bennun [Mon, 8 Mar 2021 10:24:26 +0000 (10:24 +0000)]
can: m_can: add infrastructure for internal timestamps
Add infrastucture to allow internal timestamps from the M_CAN to be
configured and retrieved.
Link: https://lore.kernel.org/r/20210308102427.63916-2-torin@maxiluxsystems.com
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Xulin Sun [Fri, 5 Feb 2021 07:25:59 +0000 (15:25 +0800)]
can: m_can: m_can_class_allocate_dev(): remove impossible error return judgment
If the CAN net device has been successfully allocated, its private
data structure is impossible to be empty, remove this redundant error
return judgment.
Link: https://lore.kernel.org/r/20210205072559.13241-2-xulin.sun@windriver.com
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stephane Grosjean [Tue, 9 Mar 2021 08:21:28 +0000 (09:21 +0100)]
can: peak_usb: add support of ONE_SHOT mode
This patch adds "ONE-SHOT" mode support to the following CAN-USB
PEAK-System GmbH interfaces:
- PCAN-USB X6
- PCAN-USB FD
- PCAN-USB Pro FD
- PCAN-Chip USB
- PCAN-USB Pro
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: split into two patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stephane Grosjean [Tue, 9 Mar 2021 08:21:26 +0000 (09:21 +0100)]
can: peak_usb: add support of ethtool set_phys_id()
This patch makes it possible to specifically flash the LED of a CAN
port of the CAN-USB interfaces of PEAK-System.
Link: https://lore.kernel.org/r/20210309122141.3276927-1-mkl@pengutronix.de
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: use common prefix PCAN_ for defines]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stephane Grosjean [Tue, 9 Mar 2021 08:21:28 +0000 (09:21 +0100)]
can: peak_usb: pcan_usb_pro_encode_msg(): use macros for flags instead of plain integers
This patch replaces the plain integers used for flags in
pcan_usb_pro_encode_msg() by macros which are already defined.
Link: https://lore.kernel.org/r/20210309082128.23125-4-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: split into two patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Arnd Bergmann [Thu, 4 Feb 2021 16:26:13 +0000 (17:26 +0100)]
can: ucan: fix alignment constraints
struct ucan_message_in contains member with 4-byte alignment
but is itself marked as unaligned, which triggers a warning:
drivers/net/can/usb/ucan.c:249:1: warning: alignment 1 of 'struct ucan_message_in' is less than 4 [-Wpacked-not-aligned]
Mark the outer structure to have the same alignment as the inner
one.
Link: https://lore.kernel.org/r/20210204162625.3099392-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Michal Simek [Thu, 4 Feb 2021 12:42:48 +0000 (13:42 +0100)]
can: xilinx_can: Simplify code by using dev_err_probe()
Use already prepared dev_err_probe() introduced by commit
a787e5400a1c
("driver core: add device probe log helper").
It simplifies EPROBE_DEFER handling.
Also unify message format for similar error cases.
Link: https://lore.kernel.org/r/91af0945ed7397b08f1af0c829450620bd92b804.1612442564.git.michal.simek@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Sat, 13 Feb 2021 11:48:28 +0000 (12:48 +0100)]
can: grcan: add missing Kconfig dependency to HAS_IOMEM
On ARCHs without IOMEM support the grcan driver fails to link due to
missing iomem functionality. This patch adds the missing Kconfig
dependency to HAS_IOMEM.
Link: https://lore.kernel.org/r/20210309140424.3331010-1-mkl@pengutronix.de
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Vincent Mailhol [Sat, 6 Mar 2021 05:40:40 +0000 (14:40 +0900)]
can: bittiming: add CAN_KBPS, CAN_MBPS and CAN_MHZ macros
Add three macro to simplify the readability of big bit timing numbers:
- CAN_KBPS: kilobits per second (one thousand)
- CAN_MBPS: megabits per second (one million)
- CAN_MHZ: megahertz per second (one million)
Example:
u32 bitrate_max = 8 * CAN_MBPS;
struct can_clock clock = {.freq = 80 * CAN_MHZ};
instead of:
u32 bitrate_max =
8000000;
struct can_clock clock = {.freq =
80000000};
Apply the new macro to driver/net/can/dev/bittiming.c.
Link: https://lore.kernel.org/r/20210306054040.76483-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Vincent Mailhol [Wed, 24 Feb 2021 00:20:08 +0000 (09:20 +0900)]
can: bittiming: add calculation for CAN FD Transmitter Delay Compensation (TDC)
The logic for the tdco calculation is to just reuse the normal sample
point: tdco = sp. Because the sample point is expressed in tenth of
percent and the tdco is expressed in time quanta, a conversion is
needed.
At the end,
ssp = tdcv + tdco
= tdcv + sp.
Another popular method is to set tdco to the middle of the bit:
tdc->tdco = can_bit_time(dbt) / 2
During benchmark tests, we could not find a clear advantages for one
of the two methods.
The tdco calculation is triggered each time the data_bittiming is
changed so that users relying on automated calculation can use the
netlink interface the exact same way without need of new parameters.
For example, a command such as:
ip link set canX type can bitrate 500000 dbitrate
4000000 fd on
would trigger the calculation.
The user using CONFIG_CAN_CALC_BITTIMING who does not want automated
calculation needs to manually set tdco to zero.
For example with:
ip link set canX type can tdco 0 bitrate 500000 dbitrate
4000000 fd on
(if the tdco parameter is provided in a previous command, it will be
overwritten).
If tdcv is set to zero (default), it is automatically calculated by
the transiver for each frame. As such, there is no code in the kernel
to calculate it.
tdcf has no automated calculation functions because we could not
figure out a formula for this parameter.
Link: https://lore.kernel.org/r/20210224002008.4158-6-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Vincent Mailhol [Wed, 24 Feb 2021 00:20:06 +0000 (09:20 +0900)]
can: netlink: move '=' operators back to previous line (checkpatch fix)
Fix the warning triggered by having an '=' at the beginning of the
line by moving it back to the previous line. Also replace all
indentations with a single space so that future entries can be more
easily added.
Extract of ./scripts/checkpatch.pl -f drivers/net/can/dev/netlink.c:
CHECK: Assignment operator '=' should be on the previous line
+ [IFLA_CAN_BITTIMING_CONST]
+ = { .len = sizeof(struct can_bittiming_const) },
CHECK: Assignment operator '=' should be on the previous line
+ [IFLA_CAN_DATA_BITTIMING]
+ = { .len = sizeof(struct can_bittiming) },
CHECK: Assignment operator '=' should be on the previous line
+ [IFLA_CAN_DATA_BITTIMING_CONST]
+ = { .len = sizeof(struct can_bittiming_const) },
Link: https://lore.kernel.org/r/20210224002008.4158-4-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Vincent Mailhol [Wed, 24 Feb 2021 00:20:05 +0000 (09:20 +0900)]
can: dev: reorder struct can_priv members for better packing
Save eight bytes of holes on x86-64 architectures by reordering struct
can_priv members.
Before:
$ pahole -C can_priv drivers/net/can/dev/dev.o
struct can_priv {
struct net_device * dev; /* 0 8 */
struct can_device_stats can_stats; /* 8 24 */
struct can_bittiming bittiming; /* 32 32 */
/* --- cacheline 1 boundary (64 bytes) --- */
struct can_bittiming data_bittiming; /* 64 32 */
const struct can_bittiming_const * bittiming_const; /* 96 8 */
const struct can_bittiming_const * data_bittiming_const; /* 104 8 */
struct can_tdc tdc; /* 112 12 */
/* XXX 4 bytes hole, try to pack */
/* --- cacheline 2 boundary (128 bytes) --- */
const struct can_tdc_const * tdc_const; /* 128 8 */
const u16 * termination_const; /* 136 8 */
unsigned int termination_const_cnt; /* 144 4 */
u16 termination; /* 148 2 */
/* XXX 2 bytes hole, try to pack */
const u32 * bitrate_const; /* 152 8 */
unsigned int bitrate_const_cnt; /* 160 4 */
/* XXX 4 bytes hole, try to pack */
const u32 * data_bitrate_const; /* 168 8 */
unsigned int data_bitrate_const_cnt; /* 176 4 */
u32 bitrate_max; /* 180 4 */
struct can_clock clock; /* 184 4 */
enum can_state state; /* 188 4 */
/* --- cacheline 3 boundary (192 bytes) --- */
u32 ctrlmode; /* 192 4 */
u32 ctrlmode_supported; /* 196 4 */
u32 ctrlmode_static; /* 200 4 */
int restart_ms; /* 204 4 */
struct delayed_work restart_work; /* 208 168 */
/* XXX last struct has 4 bytes of padding */
/* --- cacheline 5 boundary (320 bytes) was 56 bytes ago --- */
int (*do_set_bittiming)(struct net_device *); /* 376 8 */
/* --- cacheline 6 boundary (384 bytes) --- */
int (*do_set_data_bittiming)(struct net_device *); /* 384 8 */
int (*do_set_mode)(struct net_device *, enum can_mode); /* 392 8 */
int (*do_set_termination)(struct net_device *, u16); /* 400 8 */
int (*do_get_state)(const struct net_device *, enum can_state *); /* 408 8 */
int (*do_get_berr_counter)(const struct net_device *, struct can_berr_counter *); /* 416 8 */
unsigned int echo_skb_max; /* 424 4 */
/* XXX 4 bytes hole, try to pack */
struct sk_buff * * echo_skb; /* 432 8 */
/* size: 440, cachelines: 7, members: 31 */
/* sum members: 426, holes: 4, sum holes: 14 */
/* paddings: 1, sum paddings: 4 */
/* last cacheline: 56 bytes */
};
After:
$ pahole -C can_priv drivers/net/can/dev/dev.o
struct can_priv {
struct net_device * dev; /* 0 8 */
struct can_device_stats can_stats; /* 8 24 */
const struct can_bittiming_const * bittiming_const; /* 32 8 */
const struct can_bittiming_const * data_bittiming_const; /* 40 8 */
struct can_bittiming bittiming; /* 48 32 */
/* --- cacheline 1 boundary (64 bytes) was 16 bytes ago --- */
struct can_bittiming data_bittiming; /* 80 32 */
const struct can_tdc_const * tdc_const; /* 112 8 */
struct can_tdc tdc; /* 120 12 */
/* --- cacheline 2 boundary (128 bytes) was 4 bytes ago --- */
unsigned int bitrate_const_cnt; /* 132 4 */
const u32 * bitrate_const; /* 136 8 */
const u32 * data_bitrate_const; /* 144 8 */
unsigned int data_bitrate_const_cnt; /* 152 4 */
u32 bitrate_max; /* 156 4 */
struct can_clock clock; /* 160 4 */
unsigned int termination_const_cnt; /* 164 4 */
const u16 * termination_const; /* 168 8 */
u16 termination; /* 176 2 */
/* XXX 2 bytes hole, try to pack */
enum can_state state; /* 180 4 */
u32 ctrlmode; /* 184 4 */
u32 ctrlmode_supported; /* 188 4 */
/* --- cacheline 3 boundary (192 bytes) --- */
u32 ctrlmode_static; /* 192 4 */
int restart_ms; /* 196 4 */
struct delayed_work restart_work; /* 200 168 */
/* XXX last struct has 4 bytes of padding */
/* --- cacheline 5 boundary (320 bytes) was 48 bytes ago --- */
int (*do_set_bittiming)(struct net_device *); /* 368 8 */
int (*do_set_data_bittiming)(struct net_device *); /* 376 8 */
/* --- cacheline 6 boundary (384 bytes) --- */
int (*do_set_mode)(struct net_device *, enum can_mode); /* 384 8 */
int (*do_set_termination)(struct net_device *, u16); /* 392 8 */
int (*do_get_state)(const struct net_device *, enum can_state *); /* 400 8 */
int (*do_get_berr_counter)(const struct net_device *, struct can_berr_counter *); /* 408 8 */
unsigned int echo_skb_max; /* 416 4 */
/* XXX 4 bytes hole, try to pack */
struct sk_buff * * echo_skb; /* 424 8 */
/* size: 432, cachelines: 7, members: 31 */
/* sum members: 426, holes: 2, sum holes: 6 */
/* paddings: 1, sum paddings: 4 */
/* last cacheline: 48 bytes */
};
Link: https://lore.kernel.org/r/20210224002008.4158-3-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Vincent Mailhol [Wed, 24 Feb 2021 00:20:04 +0000 (09:20 +0900)]
can: add new CAN FD bittiming parameters: Transmitter Delay Compensation (TDC)
At high bit rates, the propagation delay from the TX pin to the RX pin
of the transceiver causes measurement errors: the sample point on the
RX pin might occur on the previous bit.
This issue is addressed in ISO 11898-1 section 11.3.3 "Transmitter
delay compensation" (TDC).
This patch adds two new structures: can_tdc and can_tdc_const in order
to implement this TDC.
The structures are then added to can_priv.
A controller supports TDC if an only if can_priv::tdc_const is not
NULL.
TDC is active if and only if:
- fd flag is on
- can_priv::tdc.tdco is not zero.
It is the driver responsibility to check those two conditions are met.
No new controller modes are introduced (i.e. no CAN_CTRL_MODE_TDC) in
order not to be redundant with above logic.
The names of the parameters are chosen to match existing CAN
controllers specification. References:
- Bosch C_CAN FD8:
https://www.bosch-semiconductors.com/media/ip_modules/pdf_2/c_can_fd8/users_manual_c_can_fd8_r210_1.pdf
- Microchip CAN FD Controller Module:
http://ww1.microchip.com/downloads/en/DeviceDoc/MCP251XXFD-CAN-FD-Controller-Module-Family-Reference-Manual-
20005678B.pdf
- SAM E701/S70/V70/V71 Family:
https://www.mouser.com/datasheet/2/268/
60001527A-
1284321.pdf
Link: https://lore.kernel.org/r/20210224002008.4158-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Fri, 19 Mar 2021 14:21:32 +0000 (15:21 +0100)]
can: dev: can_free_echo_skb(): extend to return can frame length
In order to implement byte queue limits (bql) in CAN drivers, the
length of the CAN frame needs to be passed into the networking stack
even if the transmission failed for some reason.
To avoid to calculate this length twice, extend can_free_echo_skb() to
return that value. Convert all users of this function, too.
This patch is the natural extension of commit:
|
9420e1d495e2 ("can: dev: can_get_echo_skb(): extend to return can
| frame length")
Link: https://lore.kernel.org/r/20210319142700.305648-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Fri, 19 Mar 2021 14:08:13 +0000 (15:08 +0100)]
can: dev: can_free_echo_skb(): don't crash the kernel if can_priv::echo_skb is accessed out of bounds
A out of bounds access to "struct can_priv::echo_skb" leads to a
kernel crash. Better print a sensible warning message instead and try
to recover.
This patch is similar to:
|
e7a6994d043a ("can: dev: __can_get_echo_skb(): Don't crash the kernel
| if can_priv::echo_skb is accessed out of bounds")
Link: https://lore.kernel.org/r/20210319142700.305648-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 10 Feb 2021 07:42:04 +0000 (08:42 +0100)]
can: dev: always create TX echo skb
So far the creation of the TX echo skb was optional and can be
controlled by the local sender of a CAN frame.
It turns out that the TX echo CAN skb can be piggybacked to carry
information in the driver from the TX- to the TX-complete handler.
Several drivers already use the return value of
can_get_echo_skb() (which is the length of the data field in the CAN
frame) for their number of transferred bytes statistics. The
statistics are not working if CAN echo skbs are disabled.
Another use case is to calculate and set the CAN frame length on the
wire, which is needed for BQL support in both the TX and TX-completion
handler.
For now in can_put_echo_skb(), which is called from the TX handler,
the skb carrying the CAN frame is discarded if no TX echo is
requested, leading to the above illustrated problems.
This patch changes the can_put_echo_skb() function, so that the echo
skb is always generated. If the sender requests no echo, the echo skb
is consumed in __can_get_echo_skb() without being passed into the RX
handler of the networking stack, but the CAN data length and CAN frame
length information is properly returned.
Link: https://lore.kernel.org/r/20210309211904.3348700-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pankaj Sharma [Thu, 18 Mar 2021 11:26:34 +0000 (16:56 +0530)]
MAINTAINERS: Update MCAN MMIO device driver maintainer
Update Chandrasekar Ramakrishnan as maintainer for mcan mmio device driver as I
will be moving to a different role.
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>