OSDN Git Service
Geert Uytterhoeven [Thu, 27 Apr 2017 12:33:05 +0000 (14:33 +0200)]
arm64: Print DT machine model in setup_machine_fdt()
On arm32, the machine model specified in the device tree is printed
during boot-up, courtesy of of_flat_dt_match_machine().
On arm64, of_flat_dt_match_machine() is not called, and the machine
model information is not available from the kernel log.
Print the machine model to make it easier to derive the machine model
from an arbitrary kernel boot log.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Florian Fainelli [Thu, 20 Apr 2017 19:05:45 +0000 (12:05 -0700)]
arm64: pmu: Wire-up Cortex A53 L2 cache events and DTLB refills
Add missing L2 cache events: read/write accesses and misses, as well as
the DTLB refills.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Tue, 21 Feb 2017 22:12:57 +0000 (22:12 +0000)]
arm64: module: split core and init PLT sections
The arm64 module PLT code allocates all PLT entries in a single core
section, since the overhead of having a separate init PLT section is
not justified by the small number of PLT entries usually required for
init code.
However, the core and init module regions are allocated independently,
and there is a corner case where the core region may be allocated from
the VMALLOC region if the dedicated module region is exhausted, but the
init region, being much smaller, can still be allocated from the module
region. This leads to relocation failures if the distance between those
regions exceeds 128 MB. (In fact, this corner case is highly unlikely to
occur on arm64, but the issue has been observed on ARM, whose module
region is much smaller).
So split the core and init PLT regions, and name the latter ".init.plt"
so it gets allocated along with (and sufficiently close to) the .init
sections that it serves. Also, given that init PLT entries may need to
be emitted for branches that target the core module, modify the logic
that disregards defined symbols to only disregard symbols that are
defined in the same section as the relocated branch instruction.
Since there may now be two PLT entries associated with each entry in
the symbol table, we can no longer hijack the symbol::st_size fields
to record the addresses of PLT entries as we emit them for zero-addend
relocations. So instead, perform an explicit comparison to check for
duplicate entries.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mark Rutland [Tue, 25 Apr 2017 11:08:50 +0000 (12:08 +0100)]
arm64: pmuv3: handle pmuv3+
Commit
f1b36dcb5c316c27 ("arm64: pmuv3: handle !PMUv3 when probing") is
a little too restrictive, and prevents the use of of backwards
compatible PMUv3 extenstions, which have a PMUver value other than 1.
For instance, ARMv8.1 PMU extensions (as implemented by ThunderX2) are
reported with PMUver value 4.
Per the usual ID register principles, at least 0x1-0x7 imply a
PMUv3-compatible PMU. It's not currently clear whether 0x8-0xe imply the
same.
For the time being, treat the value as signed, and with 0x1-0x7 treated
as meaning PMUv3 is implemented. This may be relaxed by future patches.
Reported-by: Jayachandran C <jnair@caviumnetworks.com>
Tested-by: Jayachandran C <jnair@caviumnetworks.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Marc Zyngier [Mon, 24 Apr 2017 08:04:03 +0000 (09:04 +0100)]
arm64: Add CNTFRQ_EL0 trap handler
We now trap accesses to CNTVCT_EL0 when the counter is broken
enough to require the kernel to mediate the access. But it
turns out that some existing userspace (such as OpenMPI) do
probe for the counter frequency, leading to an UNDEF exception
as CNTVCT_EL0 and CNTFRQ_EL0 share the same control bit.
The fix is to handle the exception the same way we do for CNTVCT_EL0.
Fixes:
a86bd139f2ae ("arm64: arch_timer: Enable CNTVCT_EL0 trap if workaround is enabled")
Reported-by: Hanjun Guo <guohanjun@huawei.com>
Tested-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Catalin Marinas [Wed, 12 Apr 2017 09:41:13 +0000 (10:41 +0100)]
Merge branch 'will/for-next/perf' into for-next/core
* will/for-next/perf:
arm64: pmuv3: use arm_pmu ACPI framework
arm64: pmuv3: handle !PMUv3 when probing
drivers/perf: arm_pmu: add ACPI framework
arm64: add function to get a cpu's MADT GICC table
drivers/perf: arm_pmu: split out platform device probe logic
drivers/perf: arm_pmu: move irq request/free into probe
drivers/perf: arm_pmu: split cpu-local irq request/free
drivers/perf: arm_pmu: rename irq request/free functions
drivers/perf: arm_pmu: handle no platform_device
drivers/perf: arm_pmu: simplify cpu_pmu_request_irqs()
drivers/perf: arm_pmu: factor out pmu registration
drivers/perf: arm_pmu: fold init into alloc
drivers/perf: arm_pmu: define armpmu_init_fn
drivers/perf: arm_pmu: remove pointless PMU disabling
perf: qcom: Add L3 cache PMU driver
drivers/perf: arm_pmu: split irq request from enable
drivers/perf: arm_pmu: manage interrupts per-cpu
drivers/perf: arm_pmu: rework per-cpu allocation
MAINTAINERS: Add file patterns for perf device tree bindings
Marc Zyngier [Tue, 11 Apr 2017 16:32:30 +0000 (17:32 +0100)]
arm64: Silence spurious kbuild warning on menuconfig
Since
bbb56c27228d ("arm64: Add detection code for broken .inst support
in binutils"), running any make target that doesn't involve the cross
compiler results in a spurious warning:
$ make ARCH=arm64 menuconfig
arch/arm64/Makefile:43: Detected assembler with broken .inst; disassembly will be unreliable
while
$ make ARCH=arm64 CROSS_COMPILE=aarch64-arm-linux- menuconfig
is silent (assuming your compiler is not affected). That's because
the code that tests for the workaround is always run, irrespective
of the current configuration being available or not.
An easy fix is to make the detection conditional on CONFIG_ARM64
being defined, which is only the case when actually building
something.
Fixes:
bbb56c27228d ("arm64: Add detection code for broken .inst support in binutils")
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mark Rutland [Tue, 11 Apr 2017 08:39:57 +0000 (09:39 +0100)]
arm64: pmuv3: use arm_pmu ACPI framework
Now that we have a framework to handle the ACPI bits, make the PMUv3
code use this. The framework is a little different to what was
originally envisaged, and we can drop some unused support code in the
process of moving over to it.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
[will: make armv8_pmu_driver_init static]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Tue, 11 Apr 2017 08:39:56 +0000 (09:39 +0100)]
arm64: pmuv3: handle !PMUv3 when probing
When probing via ACPI, we won't know up-front whether a CPU has a PMUv3
compatible PMU. Thus we need to consult ID registers during probe time.
This patch updates our PMUv3 probing code to test for the presence of
PMUv3 functionality before touching an PMUv3-specific registers, and
before updating the struct arm_pmu with PMUv3 data.
When a PMUv3-compatible PMU is not present, probing will return -ENODEV.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Tue, 11 Apr 2017 08:39:55 +0000 (09:39 +0100)]
drivers/perf: arm_pmu: add ACPI framework
This patch adds framework code to handle parsing PMU data out of the
MADT, sanity checking this, and managing the association of CPUs (and
their interrupts) with appropriate logical PMUs.
For the time being, we expect that only one PMU driver (PMUv3) will make
use of this, and we simply pass in a single probe function.
This is based on an earlier patch from Jeremy Linton.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Tue, 11 Apr 2017 08:39:54 +0000 (09:39 +0100)]
arm64: add function to get a cpu's MADT GICC table
Currently the ACPI parking protocol code needs to parse each CPU's MADT
GICC table to extract the mailbox address and so on. Each time we parse
a GICC table, we call back to the parking protocol code to parse it.
This has been fine so far, but we're about to have more code that needs
to extract data from the GICC tables, and adding a callback for each
user is going to get unwieldy.
Instead, this patch ensures that we stash a copy of each CPU's GICC
table at boot time, such that anything needing to parse it can later
request it. This will allow for other parsers of GICC, and for
simplification to the ACPI parking protocol code. Note that we must
store a copy, rather than a pointer, since the core ACPI code
temporarily maps/unmaps tables while iterating over them.
Since we parse the MADT before we know how many CPUs we have (and hence
before we setup the percpu areas), we must use an NR_CPUS sized array.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Tue, 11 Apr 2017 08:39:53 +0000 (09:39 +0100)]
drivers/perf: arm_pmu: split out platform device probe logic
Now that we've split the pdev and DT probing logic from the runtime
management, let's move the former into its own file. We gain a few lines
due to the copyright header and includes, but this should keep the logic
clearly separated, and paves the way for adding ACPI support in a
similar fashion.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
[will: rename nr_irqs to avoid conflict with global variable]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Tue, 11 Apr 2017 08:39:52 +0000 (09:39 +0100)]
drivers/perf: arm_pmu: move irq request/free into probe
Currently we request (and potentially free) all IRQs for a given PMU in
cpu_pmu_init(). This works for platform/DT probing today, but it doesn't
fit ACPI well as we don't have all our affinity data up-front.
In preparation for ACPI support, fold the IRQ request/free into
arm_pmu_device_probe(), which will remain specific to platform/DT
probing.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Tue, 11 Apr 2017 08:39:51 +0000 (09:39 +0100)]
drivers/perf: arm_pmu: split cpu-local irq request/free
Currently we have functions to request/free all IRQs for a given PMU.
While this works today, this won't work for ACPI, where we don't know
the full set of IRQs up front, and need to request them separately.
To enable supporting ACPI, this patch splits out the cpu-local
request/free into new functions, allowing us to request/free individual
IRQs.
As this makes it possible/necessary to request a PPI once per cpu, an
additional check is added to detect mismatched PPIs. This shouldn't
matter for the DT / platform case, as we check this when parsing.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Tue, 11 Apr 2017 08:39:50 +0000 (09:39 +0100)]
drivers/perf: arm_pmu: rename irq request/free functions
For historical reasons, portions of the arm_pmu code use a cpu_pmu_
prefix rather than an armpmu_ prefix. While a minor annoyance, this
hasn't been a problem thusfar.
However, to enable ACPI support, we'll need to expose a few things in
header files, and we should aim to keep those consistently namespaced.
In preparation for exporting our IRQ request/free functions, rename
these to have an armpmu_ prefix. For consistency, the 'cpu_pmu'
parameter is also renamed to 'armpmu'.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Tue, 11 Apr 2017 08:39:49 +0000 (09:39 +0100)]
drivers/perf: arm_pmu: handle no platform_device
In armpmu_dispatch_irq() we look at arm_pmu::plat_device to acquire
platdata, so that we can defer to platform-specific IRQ handling,
required on some 32-bit parts. With the advent of ACPI we won't always
have a platform_device, and so we must avoid trying to dereference
fields from it.
This patch fixes up armpmu_dispatch_irq() to avoid doing so, introducing
a new armpmu_get_platdata() helper.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Tue, 11 Apr 2017 08:39:48 +0000 (09:39 +0100)]
drivers/perf: arm_pmu: simplify cpu_pmu_request_irqs()
The ARM PMU framework code always uses armpmu_dispatch_irq as its common
IRQ handler. Passing this down from cpu_pmu_init() is somewhat
pointless, and gets in the way of refactoring.
This patch makes cpu_pmu_request_irqs() always use armpmu_dispatch_irq
as the handler when requesting IRQs, and removes the handler parameter
from its prototype.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Tue, 11 Apr 2017 08:39:47 +0000 (09:39 +0100)]
drivers/perf: arm_pmu: factor out pmu registration
Currently arm_pmu_device_probe contains probing logic specific to the
platform_device infrastructure, and some logic required to safely
register the PMU with various systems.
This patch factors out the logic relating to the registration of the
PMU. This makes arm_pmu_device_probe a little easier to read, and will
make it easier to reuse the logic for an ACPI-specific probing
mechanism.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Tue, 11 Apr 2017 08:39:46 +0000 (09:39 +0100)]
drivers/perf: arm_pmu: fold init into alloc
Given we always want to initialise common fields on an allocated PMU,
this patch folds this common initialisation into armpmu_alloc(). This
will make it simpler to reuse this code for an ACPI-specific probe path.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Tue, 11 Apr 2017 08:39:45 +0000 (09:39 +0100)]
drivers/perf: arm_pmu: define armpmu_init_fn
We expect an ARM PMU's init function to have a particular prototype,
which we open-code in a few places. This is less than ideal, considering
that we cast a void value to this type in one location, and a mismatch
could easily be missed.
Add a typedef so that we can ensure this is consistent.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Tue, 11 Apr 2017 08:39:44 +0000 (09:39 +0100)]
drivers/perf: arm_pmu: remove pointless PMU disabling
We currently disable the PMU temporarily in armpmu_add(). We may have
required this historically, but the perf core always disables an event's
PMU when calling event::pmu::add(), so this is not necessary.
We don't do similarly in armpmu_del(), or elsewhere, so this is
unnecessary and inconsistent, and only serves to confuse the reader.
Remove the pointless disable, simplifying armpmu_add() in the process.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Catalin Marinas [Fri, 7 Apr 2017 16:04:19 +0000 (17:04 +0100)]
Merge tag 'arch-timer-errata-prereq' of git://git./linux/kernel/git/maz/arm-platforms into for-next/core
Pre-requisites for the arch timer errata workarounds:
- Allow checking of a CPU-local erratum
- Add CNTVCT_EL0 trap handler
- Define Cortex-A73 MIDR
- Allow an erratum to be match for all revisions of a core
- Add capability to advertise Cortex-A73 erratum 858921
* tag 'arch-timer-errata-prereq' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms:
arm64: cpu_errata: Add capability to advertise Cortex-A73 erratum 858921
arm64: cpu_errata: Allow an erratum to be match for all revisions of a core
arm64: Define Cortex-A73 MIDR
arm64: Add CNTVCT_EL0 trap handler
arm64: Allow checking of a CPU-local erratum
Marc Zyngier [Mon, 20 Mar 2017 17:18:06 +0000 (17:18 +0000)]
arm64: cpu_errata: Add capability to advertise Cortex-A73 erratum 858921
In order to work around Cortex-A73 erratum 858921 in a subsequent
patch, add the required capability that advertise the erratum.
As the configuration option it depends on is not present yet,
this has no immediate effect.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Marc Zyngier [Wed, 1 Feb 2017 14:38:46 +0000 (14:38 +0000)]
arm64: cpu_errata: Allow an erratum to be match for all revisions of a core
Some minor erratum may not be fixed in further revisions of a core,
leading to a situation where the workaround needs to be updated each
time an updated core is released.
Introduce a MIDR_ALL_VERSIONS match helper that will work for all
versions of that MIDR, once and for all.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Marc Zyngier [Mon, 30 Jan 2017 14:18:49 +0000 (14:18 +0000)]
arm64: Define Cortex-A73 MIDR
As we're about to introduce a new workaround that is specific to
Cortex-A73, let's define the coresponding MIDR.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Marc Zyngier [Wed, 1 Feb 2017 11:48:58 +0000 (11:48 +0000)]
arm64: Add CNTVCT_EL0 trap handler
Since people seem to make a point in breaking the userspace visible
counter, we have no choice but to trap the access. Add the required
handler.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Marc Zyngier [Mon, 30 Jan 2017 15:39:52 +0000 (15:39 +0000)]
arm64: Allow checking of a CPU-local erratum
this_cpu_has_cap() only checks the feature array, and not the errata
one. In order to be able to check for a CPU-local erratum, allow it
to inspect the latter as well.
This is consistent with cpus_have_cap()'s behaviour, which includes
errata already.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Stephen Boyd [Wed, 5 Apr 2017 19:18:31 +0000 (12:18 -0700)]
arm64: print a fault message when attempting to write RO memory
If a page is marked read only we should print out that fact,
instead of printing out that there was a page fault. Right now we
get a cryptic error message that something went wrong with an
unhandled fault, but we don't evaluate the esr to figure out that
it was a read/write permission fault.
Instead of seeing:
Unable to handle kernel paging request at virtual address
ffff000008e460d8
pgd =
ffff800003504000
[
ffff000008e460d8] *pgd=
0000000083473003, *pud=
0000000083503003, *pmd=
0000000000000000
Internal error: Oops:
9600004f [#1] PREEMPT SMP
we'll see:
Unable to handle kernel write to read-only memory at virtual address
ffff000008e760d8
pgd =
ffff80003d3de000
[
ffff000008e760d8] *pgd=
0000000083472003, *pud=
0000000083435003, *pmd=
0000000000000000
Internal error: Oops:
9600004f [#1] PREEMPT SMP
We also add a userspace address check into is_permission_fault()
so that the function doesn't return true for ttbr0 PAN faults
when it shouldn't.
Reviewed-by: James Morse <james.morse@arm.com>
Tested-by: James Morse <james.morse@arm.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Sameer Goel [Mon, 3 Apr 2017 02:26:33 +0000 (11:26 +0900)]
efi/libstub/arm*: Set default address and size cells values for an empty dtb
In cases where a device tree is not provided (ie ACPI based system), an
empty fdt is generated by efistub. #address-cells and #size-cells are not
set in the empty fdt, so they default to 1 (4 byte wide). This can be an
issue on 64-bit systems where values representing addresses, etc may be
8 bytes wide as the default value does not align with the general
requirements for an empty DTB, and is fragile when passed to other agents
as extra care is required to read the entire width of a value.
This issue is observed on Qualcomm Technologies QDF24XX platforms when
kexec-tools inserts 64-bit addresses into the "linux,elfcorehdr" and
"linux,usable-memory-range" properties of the fdt. When the values are
later consumed, they are truncated to 32-bit.
Setting #address-cells and #size-cells to 2 at creation of the empty fdt
resolves the observed issue, and makes the fdt less fragile.
Signed-off-by: Sameer Goel <sgoel@codeaurora.org>
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
James Morse [Mon, 3 Apr 2017 02:26:06 +0000 (11:26 +0900)]
Documentation: dt: chosen properties for arm64 kdump
Add documentation for DT properties:
linux,usable-memory-range
linux,elfcorehdr
used by arm64 kdump. Those are, respectively, a usable memory range
allocated to crash dump kernel and the elfcorehdr's location within it.
Signed-off-by: James Morse <james.morse@arm.com>
[takahiro.akashi@linaro.org: update the text due to recent changes ]
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
AKASHI Takahiro [Mon, 3 Apr 2017 02:24:40 +0000 (11:24 +0900)]
Documentation: kdump: describe arm64 port
Add arch specific descriptions about kdump usage on arm64 to kdump.txt.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Baoquan He <bhe@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
AKASHI Takahiro [Mon, 3 Apr 2017 02:24:39 +0000 (11:24 +0900)]
arm64: kdump: enable kdump in defconfig
Kdump is enabled by default as kexec is.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
AKASHI Takahiro [Mon, 3 Apr 2017 02:24:38 +0000 (11:24 +0900)]
arm64: kdump: provide /proc/vmcore file
Arch-specific functions are added to allow for implementing a crash dump
file interface, /proc/vmcore, which can be viewed as a ELF file.
A user space tool, like kexec-tools, is responsible for allocating
a separate region for the core's ELF header within crash kdump kernel
memory and filling it in when executing kexec_load().
Then, its location will be advertised to crash dump kernel via a new
device-tree property, "linux,elfcorehdr", and crash dump kernel preserves
the region for later use with reserve_elfcorehdr() at boot time.
On crash dump kernel, /proc/vmcore will access the primary kernel's memory
with copy_oldmem_page(), which feeds the data page-by-page by ioremap'ing
it since it does not reside in linear mapping on crash dump kernel.
Meanwhile, elfcorehdr_read() is simple as the region is always mapped.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
AKASHI Takahiro [Mon, 3 Apr 2017 02:24:37 +0000 (11:24 +0900)]
arm64: kdump: add VMCOREINFO's for user-space tools
In addition to common VMCOREINFO's defined in
crash_save_vmcoreinfo_init(), we need to know, for crash utility,
- kimage_voffset
- PHYS_OFFSET
to examine the contents of a dump file (/proc/vmcore) correctly
due to the introduction of KASLR (CONFIG_RANDOMIZE_BASE) in v4.6.
- VA_BITS
is also required for makedumpfile command.
arch_crash_save_vmcoreinfo() appends them to the dump file.
More VMCOREINFO's may be added later.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
AKASHI Takahiro [Mon, 3 Apr 2017 02:24:36 +0000 (11:24 +0900)]
arm64: kdump: implement machine_crash_shutdown()
Primary kernel calls machine_crash_shutdown() to shut down non-boot cpus
and save registers' status in per-cpu ELF notes before starting crash
dump kernel. See kernel_kexec().
Even if not all secondary cpus have shut down, we do kdump anyway.
As we don't have to make non-boot(crashed) cpus offline (to preserve
correct status of cpus at crash dump) before shutting down, this patch
also adds a variant of smp_send_stop().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
AKASHI Takahiro [Mon, 3 Apr 2017 02:24:35 +0000 (11:24 +0900)]
arm64: hibernate: preserve kdump image around hibernation
Since arch_kexec_protect_crashkres() removes a mapping for crash dump
kernel image, the loaded data won't be preserved around hibernation.
In this patch, helper functions, crash_prepare_suspend()/
crash_post_resume(), are additionally called before/after hibernation so
that the relevant memory segments will be mapped again and preserved just
as the others are.
In addition, to minimize the size of hibernation image, crash_is_nosave()
is added to pfn_is_nosave() in order to recognize only the pages that hold
loaded crash dump kernel image as saveable. Hibernation excludes any pages
that are marked as Reserved and yet "nosave."
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Takahiro Akashi [Mon, 3 Apr 2017 02:24:34 +0000 (11:24 +0900)]
arm64: kdump: protect crash dump kernel memory
arch_kexec_protect_crashkres() and arch_kexec_unprotect_crashkres()
are meant to be called by kexec_load() in order to protect the memory
allocated for crash dump kernel once the image is loaded.
The protection is implemented by unmapping the relevant segments in crash
dump kernel memory, rather than making it read-only as other archs do,
to prevent coherency issues due to potential cache aliasing (with
mismatched attributes).
Page-level mappings are consistently used here so that we can change
the attributes of segments in page granularity as well as shrink the region
also in page granularity through /sys/kernel/kexec_crash_size, putting
the freed memory back to buddy system.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
AKASHI Takahiro [Mon, 3 Apr 2017 02:24:33 +0000 (11:24 +0900)]
arm64: mm: add set_memory_valid()
This function validates and invalidates PTE entries, and will be utilized
in kdump to protect loaded crash dump kernel image.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
AKASHI Takahiro [Mon, 3 Apr 2017 02:24:32 +0000 (11:24 +0900)]
arm64: kdump: reserve memory for crash dump kernel
"crashkernel=" kernel parameter specifies the size (and optionally
the start address) of the system ram to be used by crash dump kernel.
reserve_crashkernel() will allocate and reserve that memory at boot time
of primary kernel.
The memory range will be exposed to userspace as a resource named
"Crash kernel" in /proc/iomem.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Pratyush Anand <panand@redhat.com>
Reviewed-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
AKASHI Takahiro [Mon, 3 Apr 2017 02:24:31 +0000 (11:24 +0900)]
arm64: limit memory regions based on DT property, usable-memory-range
Crash dump kernel uses only a limited range of available memory as System
RAM. On arm64 kdump, This memory range is advertised to crash dump kernel
via a device-tree property under /chosen,
linux,usable-memory-range = <BASE SIZE>
Crash dump kernel reads this property at boot time and calls
memblock_cap_memory_range() to limit usable memory which are listed either
in UEFI memory map table or "memory" nodes of a device tree blob.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Geoff Levand <geoff@infradead.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
AKASHI Takahiro [Mon, 3 Apr 2017 02:23:55 +0000 (11:23 +0900)]
memblock: add memblock_cap_memory_range()
Add memblock_cap_memory_range() which will remove all the memblock regions
except the memory range specified in the arguments. In addition, rework is
done on memblock_mem_limit_remove_map() to re-implement it using
memblock_cap_memory_range().
This function, like memblock_mem_limit_remove_map(), will not remove
memblocks with MEMMAP_NOMAP attribute as they may be mapped and accessed
later as "device memory."
See the commit
a571d4eb55d8 ("mm/memblock.c: add new infrastructure to
address the mem limit issue").
This function is used, in a succeeding patch in the series of arm64 kdump
suuport, to limit the range of usable memory, or System RAM, on crash dump
kernel.
(Please note that "mem=" parameter is of little use for this purpose.)
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Dennis Chen <dennis.chen@arm.com>
Cc: linux-mm@kvack.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
AKASHI Takahiro [Mon, 3 Apr 2017 02:23:54 +0000 (11:23 +0900)]
memblock: add memblock_clear_nomap()
This function, with a combination of memblock_mark_nomap(), will be used
in a later kdump patch for arm64 when it temporarily isolates some range
of memory from the other memory blocks in order to create a specific
kernel mapping at boot time.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Catalin Marinas [Tue, 4 Apr 2017 17:08:47 +0000 (18:08 +0100)]
Merge branch 'arm64/common-sysreg' of git://git./linux/kernel/git/mark/linux into for-next/core
* 'arm64/common-sysreg' of git://git.kernel.org/pub/scm/linux/kernel/git/mark/linux:
arm64: sysreg: add Set/Way sys encodings
arm64: sysreg: add register encodings used by KVM
arm64: sysreg: add physical timer registers
arm64: sysreg: subsume GICv3 sysreg definitions
arm64: sysreg: add performance monitor registers
arm64: sysreg: add debug system registers
arm64: sysreg: sort by encoding
Catalin Marinas [Tue, 4 Apr 2017 17:01:55 +0000 (18:01 +0100)]
Merge tag 'acpi-arm64-for-v4.12' of git://git./linux/kernel/git/lpieralisi/linux into for-next/core
ACPI ARM64 specific changes for v4.12.
Patches contain:
- IORT kernel interface misc clean-ups
- IORT id mapping interface refactoring in preparation for platform
MSI (IORT named components -> GIC ITS mappings) devid mapping code
- IORT id mapping implementation for named components nodes to ITS nodes,
in order to provide the kernel with a firmware interface to map
platform devices devids to GIC ITS components
* tag 'acpi-arm64-for-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lpieralisi/linux:
ACPI: platform: setup MSI domain for ACPI based platform device
ACPI: platform-msi: retrieve devid from IORT
ACPI/IORT: Introduce iort_node_map_platform_id() to retrieve dev id
ACPI/IORT: Rename iort_node_map_rid() to make it generic
ACPI/IORT: Rework iort_match_node_callback() return value handling
ACPI/IORT: Add missing comment for iort_dev_find_its_id()
ACPI/IORT: Fix the indentation in iort_scan_node()
Ard Biesheuvel [Thu, 23 Mar 2017 19:00:51 +0000 (19:00 +0000)]
arm64: efi: split Image code and data into separate PE/COFF sections
To prevent unintended modifications to the kernel text (malicious or
otherwise) while running the EFI stub, describe the kernel image as
two separate sections: a .text section with read-execute permissions,
covering .text, .rodata and .init.text, and a .data section with
read-write permissions, covering .init.data, .data and .bss.
This relies on the firmware to actually take the section permission
flags into account, but this is something that is currently being
implemented in EDK2, which means we will likely start seeing it in
the wild between one and two years from now.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Thu, 23 Mar 2017 19:00:50 +0000 (19:00 +0000)]
arm64: efi: replace open coded constants with symbolic ones
Replace open coded constants with symbolic ones throughout the
Image and the EFI headers. No binary level changes are intended.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Thu, 23 Mar 2017 19:00:49 +0000 (19:00 +0000)]
arm64: efi: remove pointless dummy .reloc section
The kernel's EFI PE/COFF header contains a dummy .reloc section, and
an explanatory comment that claims that this is required for the EFI
application loader to accept the Image as a relocatable image (i.e.,
one that can be loaded at any offset and fixed up in place)
This was inherited from the x86 implementation, which has elaborate host
tooling to mangle the PE/COFF header post-link time, and which populates
the .reloc section with a single dummy base relocation. On ARM, no such
tooling exists, and the .reloc section remains empty, and is never even
exposed via the BaseRelocationTable directory entry, which is where the
PE/COFF loader looks for it.
The PE/COFF spec is unclear about relocatable images that do not require
any fixups, but the EDK2 implementation, which is the de facto reference
for PE/COFF in the UEFI space, clearly does not care, and explicitly
mentions (in a comment) that relocatable images with no base relocations
are perfectly fine, as long as they don't have the RELOCS_STRIPPED
attribute set (which is not the case for our PE/COFF image)
So simply remove the .reloc section altogether.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Thu, 23 Mar 2017 19:00:48 +0000 (19:00 +0000)]
arm64: efi: remove forbidden values from the PE/COFF header
Bring the PE/COFF header in line with the PE/COFF spec, by setting
NumberOfSymbols to 0, and removing the section alignment flags.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Thu, 23 Mar 2017 19:00:47 +0000 (19:00 +0000)]
arm64: efi: clean up Image header after PE header has been split off
After having split off the PE header, clean up the bits that remain:
use .long consistently, merge two adjacent #ifdef CONFIG_EFI blocks,
fix the offset of the PE header pointer and remove the redundant .align
that follows it.
Also, since we will be eliminating all open coded constants from the
EFI header in subsequent patches, let's replace the open coded "ARM\x64"
magic number with its .ascii equivalent.
No changes to the resulting binary image are intended.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Thu, 23 Mar 2017 19:00:46 +0000 (19:00 +0000)]
arm64: efi: move EFI header and related data to a separate .S file
In preparation of yet another round of modifications to the PE/COFF
header, macroize it and move the definition into a separate source
file.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mark Rutland [Thu, 23 Mar 2017 19:00:45 +0000 (19:00 +0000)]
include: pe.h: add some missing definitions
Add the missing IMAGE_FILE_MACHINE_ARM64 and IMAGE_DEBUG_TYPE_CODEVIEW
definitions.
We'll need them for the arm64 EFI stub...
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[ardb: add IMAGE_DEBUG_TYPE_CODEVIEW as well]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mark Rutland [Thu, 23 Mar 2017 19:00:44 +0000 (19:00 +0000)]
include: pe.h: allow for use in assembly
Some of the definitions in include/linux/pe.h would be useful for the
EFI stub headers, where values are currently open-coded. Unfortunately
they cannot be used as some structures are also defined in pe.h without
!__ASSEMBLY__ guards.
This patch moves the structure definitions into an #ifdef __ASSEMBLY__
block, so that the common value definitions can be used from assembly.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Fri, 31 Mar 2017 07:55:33 +0000 (08:55 +0100)]
arm64: relocation testing module
This module tests the module loader's ELF relocation processing
routines. When loaded, it logs output like below.
Relocation test:
-------------------------------------------------------
R_AARCH64_ABS64 0xffff880000cccccc pass
R_AARCH64_ABS32 0x00000000f800cccc pass
R_AARCH64_ABS16 0x000000000000f8cc pass
R_AARCH64_MOVW_SABS_Gn 0xffff880000cccccc pass
R_AARCH64_MOVW_UABS_Gn 0xffff880000cccccc pass
R_AARCH64_ADR_PREL_LO21 0xffffff9cf4d1a400 pass
R_AARCH64_PREL64 0xffffff9cf4d1a400 pass
R_AARCH64_PREL32 0xffffff9cf4d1a400 pass
R_AARCH64_PREL16 0xffffff9cf4d1a400 pass
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Dave Martin [Thu, 23 Mar 2017 15:14:39 +0000 (15:14 +0000)]
arm64: cpufeature: Make ID reg accessor naming less counterintuitive
read_system_reg() can readily be confused with read_sysreg(),
whereas these are really quite different in their meaning.
This patches attempts to reduce the ambiguity be reserving "sysreg"
for the actual system register accessors.
read_system_reg() is instead renamed to read_sanitised_ftr_reg(),
to make it more obvious that the Linux-defined sanitised feature
register cache is being accessed here, not the underlying
architectural system registers.
cpufeature.c's internal __raw_read_system_reg() function is renamed
in line with its actual purpose: a form of read_sysreg() that
indexes on (non-compiletime-constant) encoding rather than symbolic
register name.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Agustin Vega-Frias [Fri, 31 Mar 2017 18:13:43 +0000 (14:13 -0400)]
perf: qcom: Add L3 cache PMU driver
This adds a new dynamic PMU to the Perf Events framework to program
and control the L3 cache PMUs in some Qualcomm Technologies SOCs.
The driver supports a distributed cache architecture where the overall
cache for a socket is comprised of multiple slices each with its own PMU.
Access to each individual PMU is provided even though all CPUs share all
the slices. User space needs to aggregate to individual counts to provide
a global picture.
The driver exports formatting and event information to sysfs so it can
be used by the perf user space tools with the syntaxes:
perf stat -a -e l3cache_0_0/read-miss/
perf stat -a -e l3cache_0_0/event=0x21/
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Agustin Vega-Frias <agustinv@codeaurora.org>
[will: fixed sparse issues]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Fri, 10 Mar 2017 10:46:15 +0000 (10:46 +0000)]
drivers/perf: arm_pmu: split irq request from enable
For historical reasons, we lazily request and free interrupts in the
arm pmu driver. This requires us to refcount use of the pmu (by way of
counting the active events) in order to request/free interrupts at the
correct times, which complicates the driver somewhat.
The existing logic is flawed, as it only considers currently online CPUs
when requesting, freeing, or managing the affinity of interrupts.
Intervening hotplug events can result in erroneous IRQ affinity, online
CPUs for which interrupts have not been requested, or offline CPUs whose
interrupts are still requested.
To fix this, this patch splits the requesting of interrupts from any
per-cpu management (i.e. per-cpu enable/disable, and configuration of
cpu affinity). We now request all interrupts up-front at probe time (and
never free them, since we never unregister PMUs).
The management of affinity, and per-cpu enable/disable now happens in
our cpu hotplug callback, ensuring it occurs consistently. This means
that we must now invoke the CPU hotplug callback at boot time in order
to configure IRQs, and since the callback also resets the PMU hardware,
we can remove the duplicate reset in the probe path.
This rework renders our event refcounting unnecessary, so this is
removed.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: make armpmu_get_cpu_irq static]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Fri, 10 Mar 2017 10:46:14 +0000 (10:46 +0000)]
drivers/perf: arm_pmu: manage interrupts per-cpu
When requesting or freeing interrupts, we use platform_get_irq() to find
relevant irqs, backing this up with additional information in an
optional irq_affinity table.
This means that our irq request and free paths are tied to a
platform_device, and our request path must jump through a number of
hoops in order to determine the required affinity of each interrupt.
Given that the affinity must be static, we can compute the affinity once
up-front at probe time, simplifying the irq request and free paths. By
recording interrupts in a per-cpu data structure, we simplify a few
paths, and permit a subsequent rework of the request and free paths.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: rename local nr_irqs variable to avoid conflict with global]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Fri, 10 Mar 2017 10:46:13 +0000 (10:46 +0000)]
drivers/perf: arm_pmu: rework per-cpu allocation
For historical reasons, we allocate per-cpu data associated with a PMU
rather late, in cpu_pmu_init, after we've parsed whatever hardware
information we were provided with.
In order to allow use to store some per-cpu data early in the probe
path, we need to allocate (and initialise) the per-cpu data earlier.
This patch reworks the way we allocate the pmu and associated per-cpu
data in order to make that possible.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: make armpmu_{alloc,free} static
Signed-off-by: Will Deacon <will.deacon@arm.com>
Hanjun Guo [Tue, 7 Mar 2017 12:40:06 +0000 (20:40 +0800)]
ACPI: platform: setup MSI domain for ACPI based platform device
By allowing platform MSI domain to be created on ACPI platforms,
a platform device MSI domain can be set-up when it is probed.
In order to do that, the MSI domain the platform device connects
to should be retrieved, so the iort_get_platform_device_domain() is
introduced to retrieve the domain from the IORT kernel layer.
With the domain retrieved, we need a proper way to set the
domain to platform device.
Given that some platform devices (irqchips) require the MSI irqdomain
to be their interrupt parent domain, the MSI irqdomain should be
determined before platform device is probed but after the platform
device is allocated which means that the code setting up the MSI
irqdomain, ie acpi_configure_pmsi_domain() should be called in
acpi_platform_notify() (that is triggered after adding a device but
before the respective driver is probed) for the platform MSI domain
code set-up path to work properly.
Acked-by: Rafael J. Wysocki <rafael@kernel.org> [for glue.c]
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Hanjun Guo [Tue, 7 Mar 2017 12:40:05 +0000 (20:40 +0800)]
ACPI: platform-msi: retrieve devid from IORT
For devices connecting to an ITS, the devices need to identify themself
through a devid; this devid is represented in the IORT table in named
component node [1] for platform devices, so this patch adds code that
scans the IORT table to retrieve the devices devid.
Add an IORT interface to collect ITS devices devid to carry out platform
devices MSI mappings with IORT tables.
[1]: https://static.docs.arm.com/den0049/b/DEN0049B_IO_Remapping_Table.pdf
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log/dropped ITS changes]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Hanjun Guo [Tue, 7 Mar 2017 12:40:04 +0000 (20:40 +0800)]
ACPI/IORT: Introduce iort_node_map_platform_id() to retrieve dev id
To retrieve dev id for IORT named components nodes there are
two steps involved (second is optional):
(1) Retrieve the initial id (this may well provide the final mapping)
(2) Map the id (optional if (1) represents the map type we need), this
is needed for use cases such as NC (named component) -> SMMU -> ITS
mappings.
the iort_node_get_id() function was created for step (1) above and
iort_node_map_rid() for step (2).
Create a wrapper, named iort_node_map_platform_id(), that encompasses
the two steps at once to retrieve the dev id to provide steps (1)-(2)
functionality.
iort_node_map_platform_id() will handle the parent type so type handling
in iort_node_get_id() is duplicated, remove it and update current
iort_node_get_id() users to move them over to iort_node_map_platform_id().
Suggested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Suggested-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Hanjun Guo [Tue, 7 Mar 2017 12:40:03 +0000 (20:40 +0800)]
ACPI/IORT: Rename iort_node_map_rid() to make it generic
iort_node_map_rid() was designed to take an input id (that is not
necessarily a PCI requester id) and map it to an output id (eg an SMMU
streamid or an ITS deviceid) according to the mappings provided by an
IORT node mapping entries. This means that the iort_node_map_rid() input
id is not always a PCI requester id as its name, parameters and local
variables suggest, which is misleading.
Apply the s/rid/id substitution to the iort_node_map_rid() mapping
function and its users to make sure its intended usage is clearer.
Suggested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Geert Uytterhoeven [Sun, 12 Mar 2017 13:16:59 +0000 (14:16 +0100)]
MAINTAINERS: Add file patterns for perf device tree bindings
Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Kefeng Wang [Mon, 20 Mar 2017 12:42:55 +0000 (20:42 +0800)]
arm64: drop unnecessary newlines in show_regs()
There are two unnecessary newlines, one is in show_regs, another
is in __show_regs(), drop them.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Thu, 9 Mar 2017 20:52:09 +0000 (21:52 +0100)]
arm64: mm: set the contiguous bit for kernel mappings where appropriate
This is the third attempt at enabling the use of contiguous hints for
kernel mappings. The most recent attempt
0bfc445dec9d was reverted after
it turned out that updating permission attributes on live contiguous ranges
may result in TLB conflicts. So this time, the contiguous hint is not set
for .rodata or for the linear alias of .text/.rodata, both of which are
mapped read-write initially, and remapped read-only at a later stage.
(Note that the latter region could also be unmapped and remapped again
with updated permission attributes, given that the region, while live, is
only mapped for the convenience of the hibernation code, but that also
means the TLB footprint is negligible anyway, so why bother)
This enables the following contiguous range sizes for the virtual mapping
of the kernel image, and for the linear mapping:
granule size | cont PTE | cont PMD |
-------------+------------+------------+
4 KB | 64 KB | 32 MB |
16 KB | 2 MB | 1 GB* |
64 KB | 2 MB | 16 GB* |
* Only when built for 3 or more levels of translation. This is due to the
fact that a 2 level configuration only consists of PGDs and PTEs, and the
added complexity of dealing with folded PMDs is not justified considering
that 16 GB contiguous ranges are likely to be ignored by the hardware (and
16k/2 levels is a niche configuration)
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Thu, 9 Mar 2017 20:52:08 +0000 (21:52 +0100)]
arm64/mm: remove pointless map/unmap sequences when creating page tables
The routines __pud_populate and __pmd_populate only create a table
entry at their respective level which refers to the next level page
by its physical address, so there is no reason to map this page and
then unmap it immediately after.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Thu, 9 Mar 2017 20:52:07 +0000 (21:52 +0100)]
arm64/mmu: replace 'page_mappings_only' parameter with flags argument
In preparation of extending the policy for manipulating kernel mappings
with whether or not contiguous hints may be used in the page tables,
replace the bool 'page_mappings_only' with a flags field and a flag
NO_BLOCK_MAPPINGS.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Thu, 9 Mar 2017 20:52:06 +0000 (21:52 +0100)]
arm64/mmu: add contiguous bit to sanity bug check
A mapping with the contiguous bit cannot be safely manipulated while
live, regardless of whether the bit changes between the old and new
mapping. So take this into account when deciding whether the change
is safe.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Thu, 9 Mar 2017 20:52:05 +0000 (21:52 +0100)]
arm64/mmu: ignore debug_pagealloc for kernel segments
The debug_pagealloc facility manipulates kernel mappings in the linear
region at page granularity to detect out of bounds or use-after-free
accesses. Since the kernel segments are not allocated dynamically,
there is no point in taking the debug_pagealloc_enabled flag into
account for them, and we can use block mappings unconditionally.
Note that this applies equally to the linear alias of text/rodata:
we will never have dynamic allocations there given that the same
memory is statically in use by the kernel image.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Thu, 9 Mar 2017 20:52:04 +0000 (21:52 +0100)]
arm64/mmu: align alloc_init_pte prototype with pmd/pud versions
Align the function prototype of alloc_init_pte() with its pmd and pud
counterparts by replacing the pfn parameter with the equivalent physical
address.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Thu, 9 Mar 2017 20:52:03 +0000 (21:52 +0100)]
arm64: mmu: apply strict permissions to .init.text and .init.data
To avoid having mappings that are writable and executable at the same
time, split the init region into a .init.text region that is mapped
read-only, and a .init.data region that is mapped non-executable.
This is possible now that the alternative patching occurs via the linear
mapping, and the linear alias of the init region is always mapped writable
(but never executable).
Since the alternatives descriptions themselves are read-only data, move
those into the .init.text region.
Reviewed-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Thu, 9 Mar 2017 20:52:02 +0000 (21:52 +0100)]
arm64: mmu: map .text as read-only from the outset
Now that alternatives patching code no longer relies on the primary
mapping of .text being writable, we can remove the code that removes
the writable permissions post-init time, and map it read-only from
the outset.
To preserve the existing behavior under rodata=off, which is relied
upon by external debuggers to manage software breakpoints (as pointed
out by Mark), add an early_param() check for rodata=, and use RWX
permissions if it set to 'off'.
Reviewed-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Thu, 9 Mar 2017 20:52:01 +0000 (21:52 +0100)]
arm64: alternatives: apply boot time fixups via the linear mapping
One important rule of thumb when desiging a secure software system is
that memory should never be writable and executable at the same time.
We mostly adhere to this rule in the kernel, except at boot time, when
regions may be mapped RWX until after we are done applying alternatives
or making other one-off changes.
For the alternative patching, we can improve the situation by applying
the fixups via the linear mapping, which is never mapped with executable
permissions. So map the linear alias of .text with RW- permissions
initially, and remove the write permissions as soon as alternative
patching has completed.
Reviewed-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Thu, 9 Mar 2017 20:52:00 +0000 (21:52 +0100)]
arm64: mmu: move TLB maintenance from callers to create_mapping_late()
In preparation of refactoring the kernel mapping logic so that text regions
are never mapped writable, which would require adding explicit TLB
maintenance to new call sites of create_mapping_late() (which is currently
invoked twice from the same function), move the TLB maintenance from the
call site into create_mapping_late() itself, and change it from a full
TLB flush into a flush by VA, which is more appropriate here.
Also, given that create_mapping_late() has evolved into a routine that only
updates protection bits on existing mappings, rename it to
update_mapping_prot()
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Thu, 9 Mar 2017 20:51:59 +0000 (21:51 +0100)]
arm: kvm: move kvm_vgic_global_state out of .text section
The kvm_vgic_global_state struct contains a static key which is
written to by jump_label_init() at boot time. So in preparation of
making .text regions truly (well, almost truly) read-only, mark
kvm_vgic_global_state __ro_after_init so it moves to the .rodata
section instead.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Mon, 6 Feb 2017 15:02:42 +0000 (15:02 +0000)]
arm64: Revert "arm64: kaslr: fix breakage with CONFIG_MODVERSIONS=y"
This reverts commit
9c0e83c371cf4696926c95f9c8c77cd6ea803426, which
is no longer needed now that the modversions code plays nice with
relocatable PIE kernels.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mark Rutland [Wed, 15 Feb 2017 14:54:17 +0000 (14:54 +0000)]
arm64: move !VHE work to end of el2_setup
We only need to initialise sctlr_el1 if we're installing an EL2 stub, so
we may as well defer this until we're doing so. Similarly, we can defer
intialising CPTR_EL2 until then, as we do not access any trapped
functionality as part of el2_setup.
This patch modified el2_setup accordingly, allowing us to remove a
branch and simplify the code flow.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mark Rutland [Wed, 15 Feb 2017 14:54:16 +0000 (14:54 +0000)]
arm64: reduce el2_setup branching
The early el2_setup code is a little convoluted, with two branches where
one would do. This makes the code more painful to read than is
necessary.
We can remove a branch and simplify the logic by moving the early return
in the booted-at-EL1 case earlier in the function. This separates it
from all the setup logic that only makes sense for EL2.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Chris Redmon [Thu, 16 Mar 2017 22:10:43 +0000 (18:10 -0400)]
arm64: struct debug_info: Check CONFIG_HAVE_HW_BREAKPOINT
Check if CONFIG_HAVE_HW_BREAKPOINT is enabled before compiling in extra
data required for hardware breakpoints. Compiling out this code when hw
breakpoints are disabled saves about 272 bytes per struct task_struct.
Signed-off-by: Chris Redmon <credmonster@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Geert Uytterhoeven [Tue, 7 Mar 2017 17:43:32 +0000 (18:43 +0100)]
arm64: Add support for DMA_ATTR_FORCE_CONTIGUOUS to IOMMU
Add support for allocating physically contiguous DMA buffers on arm64
systems with an IOMMU. This can be useful when two or more devices
with different memory requirements are involved in buffer sharing.
Note that as this uses the CMA allocator, setting the
DMA_ATTR_FORCE_CONTIGUOUS attribute has a runtime-dependency on
CONFIG_DMA_CMA, just like on arm32.
For arm64 systems using swiotlb, no changes are needed to support the
allocation of physically contiguous DMA buffers:
- swiotlb always uses physically contiguous buffers (up to
IO_TLB_SEGSIZE = 128 pages),
- arm64's __dma_alloc_coherent() already calls
dma_alloc_from_contiguous() when CMA is available.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Arnd Bergmann [Tue, 14 Mar 2017 21:39:21 +0000 (22:39 +0100)]
arm64: define BUG() instruction without CONFIG_BUG
This mirrors commit
e9c38ceba8d9 ("ARM: 8455/1: define __BUG as
asm(BUG_INSTR) without CONFIG_BUG") to make the behavior of
arm64 consistent with arm and x86, and avoids lots of warnings in
randconfig builds, such as:
kernel/seccomp.c: In function '__seccomp_filter':
kernel/seccomp.c:666:1: error: no return statement in function returning non-void [-Werror=return-type]
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Hanjun Guo [Tue, 7 Mar 2017 12:39:58 +0000 (20:39 +0800)]
ACPI/IORT: Rework iort_match_node_callback() return value handling
The return value handling in iort_match_node_callback() is
too convoluted; update the iort_match_node_callback() return
value handling to make code easier to read.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Hanjun Guo [Tue, 7 Mar 2017 12:39:57 +0000 (20:39 +0800)]
ACPI/IORT: Add missing comment for iort_dev_find_its_id()
Add missing req_id parameter to the iort_dev_find_its_id() function
kernel-doc comment.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Hanjun Guo [Tue, 7 Mar 2017 12:39:56 +0000 (20:39 +0800)]
ACPI/IORT: Fix the indentation in iort_scan_node()
The indentation in the iort_scan_node() function is wrong, fix it.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: massaged commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Suzuki K Poulose [Tue, 14 Mar 2017 18:13:27 +0000 (18:13 +0000)]
arm64: v8.3: Support for weaker release consistency
ARMv8.3 adds new instructions to support Release Consistent
processor consistent (RCpc) model, which is weaker than the
RCsc model.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Suzuki K Poulose [Tue, 14 Mar 2017 18:13:26 +0000 (18:13 +0000)]
arm64: v8.3: Support for complex number instructions
ARM v8.3 adds support for new instructions to aid floating-point
multiplication and addition of complex numbers. Expose the support
via HWCAP and MRS emulation
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Suzuki K Poulose [Tue, 14 Mar 2017 18:13:25 +0000 (18:13 +0000)]
arm64: v8.3: Support for Javascript conversion instruction
ARMv8.3 adds support for a new instruction to perform conversion
from double precision floating point to integer to match the
architected behaviour of the equivalent Javascript conversion.
Expose the availability via HWCAP and MRS emulation.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Fri, 10 Mar 2017 20:32:25 +0000 (20:32 +0000)]
arm64: KVM: Add support for VPIPT I-caches
A VPIPT I-cache has two main properties:
1. Lines allocated into the cache are tagged by VMID and a lookup can
only hit lines that were allocated with the current VMID.
2. I-cache invalidation from EL1/0 only invalidates lines that match the
current VMID of the CPU doing the invalidation.
This can cause issues with non-VHE configurations, where the host runs
at EL1 and wants to invalidate I-cache entries for a guest running with
a different VMID. VHE is not affected, because the host runs at EL2 and
I-cache invalidation applies as expected.
This patch solves the problem by invalidating the I-cache when unmapping
a page at stage 2 on a system with a VPIPT I-cache but not running with
VHE enabled. Hopefully this is an obscure enough configuration that the
overhead isn't anything to worry about, although it does mean that the
by-range I-cache invalidation currently performed when mapping at stage
2 can be elided on such systems, because the I-cache will be clean for
the guest VMID following a rollover event.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Fri, 10 Mar 2017 20:32:24 +0000 (20:32 +0000)]
arm64: cache: Identify VPIPT I-caches
Add support for detecting VPIPT I-caches, as introduced by ARMv8.2.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Fri, 10 Mar 2017 20:32:23 +0000 (20:32 +0000)]
arm64: cache: Merge cachetype.h into cache.h
cachetype.h and cache.h are small and both obviously related to caches.
Merge them together to reduce clutter.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Fri, 10 Mar 2017 20:32:22 +0000 (20:32 +0000)]
arm64: cache: Remove support for ASID-tagged VIVT I-caches
As a recent change to ARMv8, ASID-tagged VIVT I-caches are removed
retrospectively from the architecture. Consequently, we don't need to
support them in Linux either.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Fri, 10 Mar 2017 20:32:21 +0000 (20:32 +0000)]
arm64: cacheinfo: Remove CCSIDR-based cache information probing
The CCSIDR_EL1.{NumSets,Associativity,LineSize} fields are only for use
in conjunction with set/way cache maintenance and are not guaranteed to
represent the actual microarchitectural features of a design.
The architecture explicitly states:
| You cannot make any inference about the actual sizes of caches based
| on these parameters.
Furthermore, CCSIDR_EL1.{WT,WB,RA,WA} have been removed retrospectively
from ARMv8 and are now considered to be UNKNOWN.
Since the kernel doesn't make use of set/way cache maintenance and it is
not possible for userspace to execute these instructions, we have no
need for the CCSIDR information in the kernel.
This patch removes the accessors, along with the related portions of the
cacheinfo support, which should instead be reintroduced when firmware has
a mechanism to provide us with reliable information.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Fri, 10 Mar 2017 20:32:20 +0000 (20:32 +0000)]
arm64: cpuinfo: remove I-cache VIPT aliasing detection
The CCSIDR_EL1.{NumSets,Associativity,LineSize} fields are only for use
in conjunction with set/way cache maintenance and are not guaranteed to
represent the actual microarchitectural features of a design.
The architecture explicitly states:
| You cannot make any inference about the actual sizes of caches based
| on these parameters.
We currently use these fields to determine whether or the I-cache is
aliasing, which is bogus and known to break on some platforms. Instead,
assume the I-cache is always aliasing if it advertises a VIPT policy.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Linus Torvalds [Mon, 20 Mar 2017 02:09:39 +0000 (19:09 -0700)]
Linux 4.11-rc3
Linus Torvalds [Mon, 20 Mar 2017 02:00:47 +0000 (19:00 -0700)]
mm/swap: don't BUG_ON() due to uninitialized swap slot cache
This BUG_ON() triggered for me once at shutdown, and I don't see a
reason for the check. The code correctly checks whether the swap slot
cache is usable or not, so an uninitialized swap slot cache is not
actually problematic afaik.
I've temporarily just switched the BUG_ON() to a WARN_ON_ONCE(), since
I'm not sure why that seemingly pointless check was there. I suspect
the real fix is to just remove it entirely, but for now we'll warn about
it but not bring the machine down.
Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 20 Mar 2017 01:49:28 +0000 (18:49 -0700)]
Merge tag 'powerpc-4.11-5' of git://git./linux/kernel/git/powerpc/linux
Pull more powerpc fixes from Michael Ellerman:
"A couple of minor powerpc fixes for 4.11:
- wire up statx() syscall
- don't print a warning on memory hotplug when HPT resizing isn't
available
Thanks to: David Gibson, Chandan Rajendra"
* tag 'powerpc-4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Don't give a warning when HPT resizing isn't available
powerpc: Wire up statx() syscall
Linus Torvalds [Mon, 20 Mar 2017 01:11:13 +0000 (18:11 -0700)]
Merge branch 'parisc-4.11-2' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
- Mikulas Patocka added support for R_PARISC_SECREL32 relocations in
modules with CONFIG_MODVERSIONS.
- Dave Anglin optimized the cache flushing for vmap ranges.
- Arvind Yadav provided a fix for a potential NULL pointer dereference
in the parisc perf code (and some code cleanups).
- I wired up the new statx system call, fixed some compiler warnings
with the access_ok() macro and fixed shutdown code to really halt a
system at shutdown instead of crashing & rebooting.
* 'parisc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix system shutdown halt
parisc: perf: Fix potential NULL pointer dereference
parisc: Avoid compiler warnings with access_ok()
parisc: Wire up statx system call
parisc: Optimize flush_kernel_vmap_range and invalidate_kernel_vmap_range
parisc: support R_PARISC_SECREL32 relocation in modules
Linus Torvalds [Mon, 20 Mar 2017 01:06:31 +0000 (18:06 -0700)]
Merge git://git./linux/kernel/git/nab/target-pending
Pull SCSI target fixes from Nicholas Bellinger:
"The bulk of the changes are in qla2xxx target driver code to address
various issues found during Cavium/QLogic's internal testing (stable
CC's included), along with a few other stability and smaller
miscellaneous improvements.
There are also a couple of different patch sets from Mike Christie,
which have been a result of his work to use target-core ALUA logic
together with tcm-user backend driver.
Finally, a patch to address some long standing issues with
pass-through SCSI export of TYPE_TAPE + TYPE_MEDIUM_CHANGER devices,
which will make folks using physical (or virtual) magnetic tape happy"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (28 commits)
qla2xxx: Update driver version to 9.00.00.00-k
qla2xxx: Fix delayed response to command for loop mode/direct connect.
qla2xxx: Change scsi host lookup method.
qla2xxx: Add DebugFS node to display Port Database
qla2xxx: Use IOCB interface to submit non-critical MBX.
qla2xxx: Add async new target notification
qla2xxx: Export DIF stats via debugfs
qla2xxx: Improve T10-DIF/PI handling in driver.
qla2xxx: Allow relogin to proceed if remote login did not finish
qla2xxx: Fix sess_lock & hardware_lock lock order problem.
qla2xxx: Fix inadequate lock protection for ABTS.
qla2xxx: Fix request queue corruption.
qla2xxx: Fix memory leak for abts processing
qla2xxx: Allow vref count to timeout on vport delete.
tcmu: Convert cmd_time_out into backend device attribute
tcmu: make cmd timeout configurable
tcmu: add helper to check if dev was configured
target: fix race during implicit transition work flushes
target: allow userspace to set state to transitioning
target: fix ALUA transition timeout handling
...
Linus Torvalds [Sun, 19 Mar 2017 22:45:02 +0000 (15:45 -0700)]
Merge branch 'libnvdimm-fixes' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull device-dax fixes from Dan Williams:
"The device-dax driver was not being careful to handle falling back to
smaller fault-granularity sizes.
The driver already fails fault attempts that are smaller than the
device's alignment, but it also needs to handle the cases where a
larger page mapping could be established. For simplicity of the
immediate fix the implementation just signals VM_FAULT_FALLBACK until
fault-size == device-alignment.
One fix is for -stable to address pmd-to-pte fallback from the
original implementation, another fix is for the new (introduced in
4.11-rc1) pud-to-pmd regression, and a typo fix comes along for the
ride.
These have received a build success notification from the kbuild
robot"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: fix debug output typo
device-dax: fix pud fault fallback handling
device-dax: fix pmd/pte fault fallback handling
Himanshu Madhani [Wed, 15 Mar 2017 16:48:56 +0000 (09:48 -0700)]
qla2xxx: Update driver version to 9.00.00.00-k
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>