OSDN Git Service
Shyam Sundar S K [Tue, 16 Feb 2021 19:07:07 +0000 (00:37 +0530)]
net: amd-xgbe: Reset the PHY rx data path when mailbox command timeout
Sometimes mailbox commands timeout when the RX data path becomes
unresponsive. This prevents the submission of new mailbox commands to DXIO.
This patch identifies the timeout and resets the RX data path so that the
next message can be submitted properly.
Fixes:
549b32af9f7c ("amd-xgbe: Simplify mailbox interface rate change code")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Mon, 15 Feb 2021 21:54:34 +0000 (15:54 -0600)]
net: ipa: initialize all resources
We configure the minimum and maximum number of various types of IPA
resources in ipa_resource_config(). It iterates over resource types
in the configuration data and assigns resource limits to each
resource group for each type.
Unfortunately, we are repeatedly initializing the resource data for
the first type, rather than initializing each of the types whose
limits are specified.
Fix this bug.
Fixes:
4a0d7579d466e ("net: ipa: avoid going past end of resource group array")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sukadev Bhattiprolu [Sat, 13 Feb 2021 04:42:50 +0000 (20:42 -0800)]
ibmvnic: serialize access to work queue on remove
The work queue is used to queue reset requests like CHANGE-PARAM or
FAILOVER resets for the worker thread. When the adapter is being removed
the adapter state is set to VNIC_REMOVING and the work queue is flushed
so no new work is added. However the check for adapter being removed is
racy in that the adapter can go into REMOVING state just after we check
and we might end up adding work just as it is being flushed (or after).
The ->rwi_lock is already being used to serialize queue/dequeue work.
Extend its usage ensure there is no race when scheduling/flushing work.
Fixes:
6954a9e4192b ("ibmvnic: Flush existing work items before device removal")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Cc:Uwe Kleine-König <uwe@kleine-koenig.org>
Cc:Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lijun Pan [Sat, 13 Feb 2021 02:49:00 +0000 (20:49 -0600)]
ibmvnic: skip send_request_unmap for timeout reset
Timeout reset will trigger the VIOS to unmap it automatically,
similarly as FAILVOER and MOBILITY events. If we unmap it
in the linux side, we will see errors like
"
30000003: Error 4 in REQUEST_UNMAP_RSP".
So, don't call send_request_unmap for timeout reset.
Fixes:
ed651a10875f ("ibmvnic: Updated reset handling")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lijun Pan [Sat, 13 Feb 2021 02:48:40 +0000 (20:48 -0600)]
ibmvnic: add memory barrier to protect long term buffer
dma_rmb() barrier is added to load the long term buffer before copying
it to socket buffer; and dma_wmb() barrier is added to update the
long term buffer before it being accessed by VIOS (virtual i/o server).
Fixes:
032c5e82847a ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Acked-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sun, 14 Feb 2021 16:36:44 +0000 (17:36 +0100)]
r8169: fix resuming from suspend on RTL8105e if machine runs on battery
Armin reported that after referenced commit his RTL8105e is dead when
resuming from suspend and machine runs on battery. This patch has been
confirmed to fix the issue.
Fixes:
e80bd76fbf56 ("r8169: work around power-saving bug on some chip versions")
Reported-by: Armin Wolf <W_Armin@gmx.de>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sebastian Andrzej Siewior [Sat, 13 Feb 2021 17:05:14 +0000 (18:05 +0100)]
net: caif: Use netif_rx_any_context().
The usage of in_interrupt() in non-core code is phased out. Ideally the
information of the calling context should be passed by the callers or the
functions be split as appropriate.
The attempt to consolidate the code by passing an arguemnt or by
distangling it failed due lack of knowledge about this driver and because
the call chains are hard to follow.
As a stop gap use netif_rx_any_context() which invokes the correct code path
depending on context and confines the in_interrupt() usage to core code.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tong Zhang [Mon, 15 Feb 2021 19:23:07 +0000 (14:23 -0500)]
net: wan/lmc: dont print format string when not available
dev->name is determined only after calling register_hdlc_device(),
however ,it is used by printk before the name is fully determined.
[ 4.565137] hdlc%d: detected at
e8000000, irq 11
Instead of printing out a %d, print hdlc directly
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tong Zhang [Mon, 15 Feb 2021 19:17:56 +0000 (14:17 -0500)]
net: wan/lmc: unregister device when no matching device is found
lmc set sc->lmc_media pointer when there is a matching device.
However, when no matching device is found, this pointer is NULL
and the following dereference will result in a null-ptr-deref.
To fix this issue, unregister the hdlc device and return an error.
[ 4.569359] BUG: KASAN: null-ptr-deref in lmc_init_one.cold+0x2b6/0x55d [lmc]
[ 4.569748] Read of size 8 at addr
0000000000000008 by task modprobe/95
[ 4.570102]
[ 4.570187] CPU: 0 PID: 95 Comm: modprobe Not tainted 5.11.0-rc7 #94
[ 4.570527] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.13.0-48-gd9c812dda519-preb4
[ 4.571125] Call Trace:
[ 4.571261] dump_stack+0x7d/0xa3
[ 4.571445] kasan_report.cold+0x10c/0x10e
[ 4.571667] ? lmc_init_one.cold+0x2b6/0x55d [lmc]
[ 4.571932] lmc_init_one.cold+0x2b6/0x55d [lmc]
[ 4.572186] ? lmc_mii_readreg+0xa0/0xa0 [lmc]
[ 4.572432] local_pci_probe+0x6f/0xb0
[ 4.572639] pci_device_probe+0x171/0x240
[ 4.572857] ? pci_device_remove+0xe0/0xe0
[ 4.573080] ? kernfs_create_link+0xb6/0x110
[ 4.573315] ? sysfs_do_create_link_sd.isra.0+0x76/0xe0
[ 4.573598] really_probe+0x161/0x420
[ 4.573799] driver_probe_device+0x6d/0xd0
[ 4.574022] device_driver_attach+0x82/0x90
[ 4.574249] ? device_driver_attach+0x90/0x90
[ 4.574485] __driver_attach+0x60/0x100
[ 4.574694] ? device_driver_attach+0x90/0x90
[ 4.574931] bus_for_each_dev+0xe1/0x140
[ 4.575146] ? subsys_dev_iter_exit+0x10/0x10
[ 4.575387] ? klist_node_init+0x61/0x80
[ 4.575602] bus_add_driver+0x254/0x2a0
[ 4.575812] driver_register+0xd3/0x150
[ 4.576021] ? 0xffffffffc0018000
[ 4.576202] do_one_initcall+0x84/0x250
[ 4.576411] ? trace_event_raw_event_initcall_finish+0x150/0x150
[ 4.576733] ? unpoison_range+0xf/0x30
[ 4.576938] ? ____kasan_kmalloc.constprop.0+0x84/0xa0
[ 4.577219] ? unpoison_range+0xf/0x30
[ 4.577423] ? unpoison_range+0xf/0x30
[ 4.577628] do_init_module+0xf8/0x350
[ 4.577833] load_module+0x3fe6/0x4340
[ 4.578038] ? vm_unmap_ram+0x1d0/0x1d0
[ 4.578247] ? ____kasan_kmalloc.constprop.0+0x84/0xa0
[ 4.578526] ? module_frob_arch_sections+0x20/0x20
[ 4.578787] ? __do_sys_finit_module+0x108/0x170
[ 4.579037] __do_sys_finit_module+0x108/0x170
[ 4.579278] ? __ia32_sys_init_module+0x40/0x40
[ 4.579523] ? file_open_root+0x200/0x200
[ 4.579742] ? do_sys_open+0x85/0xe0
[ 4.579938] ? filp_open+0x50/0x50
[ 4.580125] ? exit_to_user_mode_prepare+0xfc/0x130
[ 4.580390] do_syscall_64+0x33/0x40
[ 4.580586] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 4.580859] RIP: 0033:0x7f1a724c3cf7
[ 4.581054] Code: 48 89 57 30 48 8b 04 24 48 89 47 38 e9 1d a0 02 00 48 89 f8 48 89 f7 48 89 d6 48 891
[ 4.582043] RSP: 002b:
00007fff44941c68 EFLAGS:
00000246 ORIG_RAX:
0000000000000139
[ 4.582447] RAX:
ffffffffffffffda RBX:
00000000012ada70 RCX:
00007f1a724c3cf7
[ 4.582827] RDX:
0000000000000000 RSI:
00000000012ac9e0 RDI:
0000000000000003
[ 4.583207] RBP:
0000000000000003 R08:
0000000000000000 R09:
0000000000000001
[ 4.583587] R10:
00007f1a72527300 R11:
0000000000000246 R12:
00000000012ac9e0
[ 4.583968] R13:
0000000000000000 R14:
00000000012acc90 R15:
0000000000000001
[ 4.584349] ==================================================================
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Mon, 15 Feb 2021 12:05:32 +0000 (12:05 +0000)]
b43: N-PHY: Fix the update of coef for the PHY revision >= 3case
The documentation for the PHY update [1] states:
Loop 4 times with index i
If PHY Revision >= 3
Copy table[i] to coef[i]
Otherwise
Set coef[i] to 0
the copy of the table to coef is currently implemented the wrong way
around, table is being updated from uninitialized values in coeff.
Fix this by swapping the assignment around.
[1] https://bcm-v4.sipsolutions.net/802.11/PHY/N/RestoreCal/
Fixes:
2f258b74d13c ("b43: N-PHY: implement restoring general configuration")
Addresses-Coverity: ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ayush Sawal [Mon, 15 Feb 2021 11:42:26 +0000 (17:12 +0530)]
cxgb4/chtls/cxgbit: Keeping the max ofld immediate data size same in cxgb4 and ulds
The Max imm data size in cxgb4 is not similar to the max imm data size
in the chtls. This caused an mismatch in output of is_ofld_imm() of
cxgb4 and chtls. So fixed this by keeping the max wreq size of imm data
same in both chtls and cxgb4 as MAX_IMM_OFLD_TX_DATA_WR_LEN.
As cxgb4's max imm. data value for ofld packets is changed to
MAX_IMM_OFLD_TX_DATA_WR_LEN. Using the same in cxgbit also.
Fixes:
36bedb3f2e5b8 ("crypto: chtls - Inline TLS record Tx")
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tong Zhang [Sun, 14 Feb 2021 23:43:08 +0000 (18:43 -0500)]
atm: idt77252: fix build broken on amd64
idt77252 is broken and wont load on amd64 systems
modprobe idt77252 shows the following
idt77252_init: skb->cb is too small (48 < 56)
Add packed attribute to struct idt77252_skb_prv and struct atm_skb_data
so that the total size can be <= sizeof(skb->cb)
Also convert runtime size check to buildtime size check in
idt77252_init()
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Hancock [Sat, 13 Feb 2021 00:17:48 +0000 (18:17 -0600)]
net: axienet: Handle deferred probe on clock properly
This driver is set up to use a clock mapping in the device tree if it is
present, but still work without one for backward compatibility. However,
if getting the clock returns -EPROBE_DEFER, then we need to abort and
return that error from our driver initialization so that the probe can
be retried later after the clock is set up.
Move clock initialization to earlier in the process so we do not waste as
much effort if the clock is not yet available. Switch to use
devm_clk_get_optional and abort initialization on any error reported.
Also enable the clock regardless of whether the controller is using an MDIO
bus, as the clock is required in any case.
Fixes:
09a0354cadec267be7f ("net: axienet: Use clock framework to get device clock rate")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dany Madden [Fri, 12 Feb 2021 20:16:30 +0000 (15:16 -0500)]
ibmvnic: change IBMVNIC_MAX_IND_DESCS to 16
The supported indirect subcrq entries on Power8 is 16. Power9
supports 128. Redefined this value to 16 to minimize the driver from
having to reset when migrating between Power9 and Power8. In our rx/tx
performance testing, we found no performance difference between 16 and
128 at this time.
Fixes:
f019fb6392e5 ("ibmvnic: Introduce indirect subordinate Command Response Queue buffer")
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Fri, 12 Feb 2021 15:12:25 +0000 (16:12 +0100)]
flow_dissector: fix TTL and TOS dissection on IPv4 fragments
the following command:
# tc filter add dev $h2 ingress protocol ip pref 1 handle 101 flower \
$tcflags dst_ip 192.0.2.2 ip_ttl 63 action drop
doesn't drop all IPv4 packets that match the configured TTL / destination
address. In particular, if "fragment offset" or "more fragments" have non
zero value in the IPv4 header, setting of FLOW_DISSECTOR_KEY_IP is simply
ignored. Fix this dissecting IPv4 TTL and TOS before fragment info; while
at it, add a selftest for tc flower's match on 'ip_ttl' that verifies the
correct behavior.
Fixes:
518d8a2e9bad ("net/flow_dissector: add support for dissection of misc ip header fields")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doug Brown [Fri, 12 Feb 2021 05:27:54 +0000 (21:27 -0800)]
appletalk: Fix skb allocation size in loopback case
If a DDP broadcast packet is sent out to a non-gateway target, it is
also looped back. There is a potential for the loopback device to have a
longer hardware header length than the original target route's device,
which can result in the skb not being created with enough room for the
loopback device's hardware header. This patch fixes the issue by
determining that a loopback will be necessary prior to allocating the
skb, and if so, ensuring the skb has enough room.
This was discovered while testing a new driver that creates a LocalTalk
network interface (LTALK_HLEN = 1). It caused an skb_under_panic.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 13 Feb 2021 00:15:23 +0000 (16:15 -0800)]
Merge https://git./linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2021-02-13
The following pull-request contains BPF updates for your *net* tree.
We've added 2 non-merge commits during the last 3 day(s) which contain
a total of 2 files changed, 9 insertions(+), 11 deletions(-).
The main changes are:
1) Fix mod32 truncation handling in verifier, from Daniel Borkmann.
2) Fix XDP redirect tests to explicitly use bash, from Björn Töpel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 10 Feb 2021 13:14:42 +0000 (14:14 +0100)]
bpf: Fix truncation handling for mod32 dst reg wrt zero
Recently noticed that when mod32 with a known src reg of 0 is performed,
then the dst register is 32-bit truncated in verifier:
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (b7) r0 = 0
1: R0_w=inv0 R1=ctx(id=0,off=0,imm=0) R10=fp0
1: (b7) r1 = -1
2: R0_w=inv0 R1_w=inv-1 R10=fp0
2: (b4) w2 = -1
3: R0_w=inv0 R1_w=inv-1 R2_w=inv4294967295 R10=fp0
3: (9c) w1 %= w0
4: R0_w=inv0 R1_w=inv(id=0,umax_value=
4294967295,var_off=(0x0; 0xffffffff)) R2_w=inv4294967295 R10=fp0
4: (b7) r0 = 1
5: R0_w=inv1 R1_w=inv(id=0,umax_value=
4294967295,var_off=(0x0; 0xffffffff)) R2_w=inv4294967295 R10=fp0
5: (1d) if r1 == r2 goto pc+1
R0_w=inv1 R1_w=inv(id=0,umax_value=
4294967295,var_off=(0x0; 0xffffffff)) R2_w=inv4294967295 R10=fp0
6: R0_w=inv1 R1_w=inv(id=0,umax_value=
4294967295,var_off=(0x0; 0xffffffff)) R2_w=inv4294967295 R10=fp0
6: (b7) r0 = 2
7: R0_w=inv2 R1_w=inv(id=0,umax_value=
4294967295,var_off=(0x0; 0xffffffff)) R2_w=inv4294967295 R10=fp0
7: (95) exit
7: R0=inv1 R1=inv(id=0,umin_value=
4294967295,umax_value=
4294967295,var_off=(0x0; 0xffffffff)) R2=inv4294967295 R10=fp0
7: (95) exit
However, as a runtime result, we get 2 instead of 1, meaning the dst
register does not contain (u32)-1 in this case. The reason is fairly
straight forward given the 0 test leaves the dst register as-is:
# ./bpftool p d x i 23
0: (b7) r0 = 0
1: (b7) r1 = -1
2: (b4) w2 = -1
3: (16) if w0 == 0x0 goto pc+1
4: (9c) w1 %= w0
5: (b7) r0 = 1
6: (1d) if r1 == r2 goto pc+1
7: (b7) r0 = 2
8: (95) exit
This was originally not an issue given the dst register was marked as
completely unknown (aka 64 bit unknown). However, after
468f6eafa6c4
("bpf: fix 32-bit ALU op verification") the verifier casts the register
output to 32 bit, and hence it becomes 32 bit unknown. Note that for
the case where the src register is unknown, the dst register is marked
64 bit unknown. After the fix, the register is truncated by the runtime
and the test passes:
# ./bpftool p d x i 23
0: (b7) r0 = 0
1: (b7) r1 = -1
2: (b4) w2 = -1
3: (16) if w0 == 0x0 goto pc+2
4: (9c) w1 %= w0
5: (05) goto pc+1
6: (bc) w1 = w1
7: (b7) r0 = 1
8: (1d) if r1 == r2 goto pc+1
9: (b7) r0 = 2
10: (95) exit
Semantics also match with {R,W}x mod{64,32} 0 -> {R,W}x. Invalid div
has always been {R,W}x div{64,32} 0 -> 0. Rewrites are as follows:
mod32: mod64:
(16) if w0 == 0x0 goto pc+2 (15) if r0 == 0x0 goto pc+1
(9c) w1 %= w0 (9f) r1 %= r0
(05) goto pc+1
(bc) w1 = w1
Fixes:
468f6eafa6c4 ("bpf: fix 32-bit ALU op verification")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
David S. Miller [Fri, 12 Feb 2021 03:25:12 +0000 (19:25 -0800)]
Merge tag 'mlx5-fixes-2021-02-11' of git://git./linux/kernel/git/saeed/linux
mlx5-fixes-2021-02-11
Saeed Mahameed says:
====================
mlx5 fixes 2021-02-11
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v5.4
('net/mlx5e: E-switch, Fix rate calculation for overflow')i
For -stable v5.10
('net/mlx5: Disallow RoCE on multi port slave device')
('net/mlx5: Disable devlink reload for multi port slave device')
('net/mlx5e: Don't change interrupt moderation params when DIM is enabled')
('net/mlx5e: Replace synchronize_rcu with synchronize_net')
('net/mlx5e: Enable XDP for Connect-X IPsec capable devices')
('net/mlx5e: kTLS, Use refcounts to free kTLS RX priv context')
('net/mlx5e: Check tunnel offload is required before setting SWP')
('net/mlx5: Fix health error state handling')
('net/mlx5: Disable devlink reload for lag devices')
('net/mlx5e: CT: manage the lifetime of the ct entry object')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Moshe Shemesh [Tue, 26 Jan 2021 14:46:11 +0000 (16:46 +0200)]
net/mlx5e: Check tunnel offload is required before setting SWP
Check that tunnel offload is required before setting Software Parser
offsets to get Geneve HW offload. In case of Geneve packet we check HW
offload support of SWP in mlx5e_tunnel_features_check() and set features
accordingly, this should be reflected in skb offload requested by the
kernel and we should add the Software Parser offsets only if requested.
Otherwise, in case HW doesn't support SWP for Geneve, data path will
mistakenly try to offload Geneve SKBs with skb->encapsulation set,
regardless of whether offload was requested or not on this specific SKB.
Fixes:
e3cfc7e6b7bd ("net/mlx5e: TX, Add geneve tunnel stateless offload support")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Oz Shlomo [Tue, 12 Jan 2021 12:37:37 +0000 (12:37 +0000)]
net/mlx5e: CT: manage the lifetime of the ct entry object
The ct entry object is accessed by the ct add, del, stats and restore
methods. In addition, it is referenced from several hash tables.
The lifetime of the ct entry object was not managed which triggered race
conditions as in the following kasan dump:
[ 3374.973945] ==================================================================
[ 3374.988552] BUG: KASAN: use-after-free in memcmp+0x4c/0x98
[ 3374.999590] Read of size 1 at addr
ffff00036129ea55 by task ksoftirqd/1/15
[ 3375.016415] CPU: 1 PID: 15 Comm: ksoftirqd/1 Tainted: G O 5.4.31+ #1
[ 3375.055301] Call trace:
[ 3375.060214] dump_backtrace+0x0/0x238
[ 3375.067580] show_stack+0x24/0x30
[ 3375.074244] dump_stack+0xe0/0x118
[ 3375.081085] print_address_description.isra.9+0x74/0x3d0
[ 3375.091771] __kasan_report+0x198/0x1e8
[ 3375.099486] kasan_report+0xc/0x18
[ 3375.106324] __asan_load1+0x60/0x68
[ 3375.113338] memcmp+0x4c/0x98
[ 3375.119409] mlx5e_tc_ct_restore_flow+0x3a4/0x6f8 [mlx5_core]
[ 3375.131073] mlx5e_rep_tc_update_skb+0x1d4/0x2f0 [mlx5_core]
[ 3375.142553] mlx5e_handle_rx_cqe_rep+0x198/0x308 [mlx5_core]
[ 3375.154034] mlx5e_poll_rx_cq+0x2a0/0x1060 [mlx5_core]
[ 3375.164459] mlx5e_napi_poll+0x1d4/0xa78 [mlx5_core]
[ 3375.174453] net_rx_action+0x28c/0x7a8
[ 3375.182004] __do_softirq+0x1b4/0x5d0
Manage the lifetime of the ct entry object by using synchornization
mechanisms for concurrent access.
Fixes:
ac991b48d43c ("net/mlx5e: CT: Offload established flows")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Shay Drory [Thu, 31 Dec 2020 13:04:08 +0000 (15:04 +0200)]
net/mlx5: Disable devlink reload for lag devices
Devlink reload can't be allowed on lag devices since reloading one lag
device will cause traffic on the bond to get stucked.
Users who wish to reload a lag device, need to remove the device from
the bond, and only then reload it.
Fixes:
4383cfcc65e7 ("net/mlx5: Add devlink reload")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Shay Drory [Sun, 3 Jan 2021 08:09:59 +0000 (10:09 +0200)]
net/mlx5: Disallow RoCE on lag device
In lag mode, setting roce enabled/disable of lag device have no effect.
e.g.: bond device (roce/vf_lag) roce status remain unchanged.
Therefore disable it and add an error message.
Fixes:
cc9defcbb8fa ("net/mlx5: Handle "enable_roce" devlink param")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Shay Drory [Wed, 30 Dec 2020 08:58:34 +0000 (10:58 +0200)]
net/mlx5: Disallow RoCE on multi port slave device
In dual port mode, setting roce enabled/disable for the slave device
have no effect. e.g.: the slave device roce status remain unchanged.
Therefore disable it and add an error message.
Enable or disable roce of the master device affect both master and slave
devices.
Fixes:
cc9defcbb8fa ("net/mlx5: Handle "enable_roce" devlink param")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Shay Drory [Wed, 30 Dec 2020 07:58:32 +0000 (09:58 +0200)]
net/mlx5: Disable devlink reload for multi port slave device
Devlink reload can't be allowed on a multi port slave device, because
reload of slave device doesn't take effect.
The right flow is to disable devlink reload for multi port slave
device. Hence, disabling it in mlx5_core probing.
Fixes:
4383cfcc65e7 ("net/mlx5: Add devlink reload")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maxim Mikityanskiy [Fri, 22 Jan 2021 16:42:29 +0000 (18:42 +0200)]
net/mlx5e: kTLS, Use refcounts to free kTLS RX priv context
wait_for_resync is unreliable - if it timeouts, priv_rx will be freed
anyway. However, mlx5e_ktls_handle_get_psv_completion will be called
sooner or later, leading to use-after-free. For example, it can happen
if a CQ error happened, and ICOSQ stopped, but later on the queues are
destroyed, and ICOSQ is flushed with mlx5e_free_icosq_descs.
This patch converts the lifecycle of priv_rx to fully refcount-based, so
that the struct won't be freed before the refcount goes to zero.
Fixes:
0419d8c9d8f8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maxim Mikityanskiy [Wed, 10 Feb 2021 07:25:28 +0000 (09:25 +0200)]
net/mlx5e: Fix CQ params of ICOSQ and async ICOSQ
The commit mentioned below has split the parameters of ICOSQ and async
ICOSQ, but it contained a typo: the CQ parameters were swapped for ICOSQ
and async ICOSQ. Async ICOSQ is longer than the normal ICOSQ, and the CQ
size must be the same as the size of the corresponding SQ, but due to
this bug, the CQ of async ICOSQ was much shorter than async ICOSQ
itself. It led to overflows of the CQ with such messages in dmesg, in
particular, when running multiple kTLS-offloaded streams:
mlx5_core 0000:08:00.0: cq_err_event_notifier:529:(pid 9422): CQ error
on CQN 0x406, syndrome 0x1
mlx5_core 0000:08:00.0 eth2: mlx5e_cq_error_event: cqn=0x000406
event=0x04
This commit fixes the issue by using the corresponding parameters for
ICOSQ and async ICOSQ.
Fixes:
c293ac927fbb ("net/mlx5e: Refactor build channel params")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maxim Mikityanskiy [Mon, 1 Feb 2021 12:01:27 +0000 (14:01 +0200)]
net/mlx5e: Replace synchronize_rcu with synchronize_net
The commit cited below switched from using napi_synchronize to
synchronize_rcu to have a guarantee that it will finish in finite time.
However, on average, synchronize_rcu takes more time than
napi_synchronize. Given that it's called multiple times per channel on
deactivation, it accumulates to a significant amount, which causes
timeouts in some applications (for example, when using bonding with
NetworkManager).
This commit replaces synchronize_rcu with synchronize_net, which is
faster when called under rtnl_lock, allowing to speed up the described
flow.
Fixes:
9c25a22dfb00 ("net/mlx5e: Use synchronize_rcu to sync with NAPI")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Shay Drory [Mon, 23 Nov 2020 06:39:10 +0000 (08:39 +0200)]
net/mlx5: Fix health error state handling
Currently, when we discover a fatal error, we are queueing a work that
will wait for a lock in order to enter the device to error state.
Meanwhile, FW commands are still being processed, and gets timeouts.
This can block the driver for few minutes before the work will manage
to get the lock and enter to error state.
Setting the device to error state before queueing health work, in order
to avoid FW commands being processed while the work is waiting for the
lock.
Fixes:
c1d4d2e92ad6 ("net/mlx5: Avoid calling sleeping function by the health poll thread")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maxim Mikityanskiy [Wed, 3 Feb 2021 16:01:03 +0000 (18:01 +0200)]
net/mlx5e: Change interrupt moderation channel params also when channels are closed
struct mlx5e_params contains fields ({rx,tx}_cq_moderation) that depend
on two things: whether DIM is enabled and the state of a private flag
(MLX5E_PFLAG_{RX,TX}_CQE_BASED_MODER). Whenever the DIM state changes,
mlx5e_reset_{rx,tx}_moderation is called to update the fields, however,
only if the channels are open. The flow where the channels are closed
misses the required update of the fields. This commit moves the calls of
mlx5e_reset_{rx,tx}_moderation, so that they run in both flows.
Fixes:
ebeaf084ad5c ("net/mlx5e: Properly set default values when disabling adaptive moderation")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maxim Mikityanskiy [Wed, 3 Feb 2021 15:55:58 +0000 (17:55 +0200)]
net/mlx5e: Don't change interrupt moderation params when DIM is enabled
When mlx5e_ethtool_set_coalesce doesn't change DIM state
(enabled/disabled), it calls mlx5e_set_priv_channels_coalesce
unconditionally, which in turn invokes a firmware command to set
interrupt moderation parameters. It shouldn't happen while DIM manages
those parameters dynamically (it might even be happening at the same
time).
This patch fixes it by splitting mlx5e_set_priv_channels_coalesce into
two functions (for RX and TX) and calling them only when DIM is disabled
(for RX and TX respectively).
Fixes:
cb3c7fd4f839 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Raed Salem [Mon, 25 Jan 2021 07:58:22 +0000 (09:58 +0200)]
net/mlx5e: Enable XDP for Connect-X IPsec capable devices
This limitation was inherited by previous Innova (FPGA) IPsec
implementation, it uses its private set of RQ handlers which
does not support XDP, for Connect-X this is no longer true.
Fix by keeping this limitation only for Innova IPsec supporting devices,
as otherwise this limitation effectively wrongly blocks XDP for all
future Connect-X devices for all flows even if IPsec offload is not
used.
Fixes:
2d64663cd559 ("net/mlx5: IPsec: Add HW crypto offload support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Alaa Hleihel <alaa@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Raed Salem [Sun, 24 Jan 2021 20:40:23 +0000 (22:40 +0200)]
net/mlx5e: Enable striding RQ for Connect-X IPsec capable devices
This limitation was inherited by previous Innova (FPGA) IPsec
implementation, it uses its private set of RQ handlers which does
not support striding rq, for Connect-X this is no longer true.
Fix by keeping this limitation only for Innova IPsec supporting devices,
as otherwise this limitation effectively wrongly blocks striding RQs for
all future Connect-X devices for all flows even if IPsec offload is not
used.
Fixes:
2d64663cd559 ("net/mlx5: IPsec: Add HW crypto offload support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Parav Pandit [Tue, 12 Jan 2021 14:13:22 +0000 (16:13 +0200)]
net/mlx5e: E-switch, Fix rate calculation for overflow
rate_bytes_ps is a 64-bit field. It passed as 32-bit field to
apply_police_params(). Due to this when police rate is higher
than 4Gbps, 32-bit calculation ignores the carry. This results
in incorrect rate configurationn the device.
Fix it by performing 64-bit calculation.
Fixes:
fcb64c0f5640 ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
David S. Miller [Fri, 12 Feb 2021 02:30:55 +0000 (18:30 -0800)]
Merge branch 'mptcp-Miscellaneous-fixes'
Mat Martineau says:
====================
mptcp: Miscellaneous fixes
Here are some MPTCP fixes for the -net tree, addressing various issues
we have seen thanks to syzkaller and other testing:
Patch 1 correctly propagates errors at connection time and for TCP
fallback connections.
Patch 2 sets the expected poll() events on SEND_SHUTDOWN.
Patch 3 fixes a retranmit crash and unneeded retransmissions.
Patch 4 fixes possible uninitialized data on the error path during
socket creation.
Patch 5 addresses a problem with MPTCP window updates.
Patch 6 fixes a case where MPTCP retransmission can get stuck.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 11 Feb 2021 23:30:42 +0000 (15:30 -0800)]
mptcp: add a missing retransmission timer scheduling
Currently we do not schedule the MPTCP retransmission
timer after pushing the data when such action happens
in the subflow context.
This may cause hang-up on active-backup scenarios, or
even when only single subflow msks are involved, if we lost
some peer's ack.
Fixes:
6e628cd3a8f7 ("mptcp: use mptcp release_cb for delayed tasks")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 11 Feb 2021 23:30:41 +0000 (15:30 -0800)]
mptcp: better msk receive window updates
Move mptcp_cleanup_rbuf() related checks inside the mentioned
helper and extend them to mirror TCP checks more closely.
Additionally drop the 'rmem_pending' hack, since commit
879526030c8b
("mptcp: protect the rx path with the msk socket spinlock") we
can use instead 'rmem_released'.
Fixes:
ea4ca586b16f ("mptcp: refine MPTCP-level ack scheduling")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 11 Feb 2021 23:30:40 +0000 (15:30 -0800)]
mptcp: init mptcp request socket earlier
The mptcp subflow route_req() callback performs the subflow
req initialization after the route_req() check. If the latter
fails, mptcp-specific bits of the current request sockets
are left uninitialized.
The above causes bad things at req socket disposal time, when
the mptcp resources are cleared.
This change addresses the issue by splitting subflow_init_req()
into the actual initialization and the mptcp-specific checks.
The initialization is moved before any possibly failing check.
Reported-by: Christoph Paasch <cpaasch@apple.com>
Fixes:
7ea851d19b23 ("tcp: merge 'init_req' and 'route_req' functions")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 11 Feb 2021 23:30:39 +0000 (15:30 -0800)]
mptcp: fix spurious retransmissions
Syzkaller was able to trigger the following splat again:
WARNING: CPU: 1 PID: 12512 at net/mptcp/protocol.c:761 mptcp_reset_timer+0x12a/0x160 net/mptcp/protocol.c:761
Modules linked in:
CPU: 1 PID: 12512 Comm: kworker/1:6 Not tainted 5.10.0-rc6 #52
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Workqueue: events mptcp_worker
RIP: 0010:mptcp_reset_timer+0x12a/0x160 net/mptcp/protocol.c:761
Code: e8 4b 0c ad ff e8 56 21 88 fe 48 b8 00 00 00 00 00 fc ff df 48 c7 04 03 00 00 00 00 48 83 c4 40 5b 5d 41 5c c3 e8 36 21 88 fe <0f> 0b 41 bc c8 00 00 00 eb 98 e8 e7 b1 af fe e9 30 ff ff ff 48 c7
RSP: 0018:
ffffc900018c7c68 EFLAGS:
00010293
RAX:
ffff888108cb1c80 RBX:
1ffff92000318f8d RCX:
ffffffff82ad0307
RDX:
0000000000000000 RSI:
ffffffff82ad036a RDI:
0000000000000007
RBP:
ffff888113e2d000 R08:
ffff888108cb1c80 R09:
ffffed10227c5ab7
R10:
ffff888113e2d5b7 R11:
ffffed10227c5ab6 R12:
0000000000000000
R13:
ffff88801f100000 R14:
ffff888113e2d5b0 R15:
0000000000000001
FS:
0000000000000000(0000) GS:
ffff88811b500000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007fd76a874ef8 CR3:
000000001689c005 CR4:
0000000000170ee0
Call Trace:
mptcp_worker+0xaa4/0x1560 net/mptcp/protocol.c:2334
process_one_work+0x8d3/0x1200 kernel/workqueue.c:2272
worker_thread+0x9c/0x1090 kernel/workqueue.c:2418
kthread+0x303/0x410 kernel/kthread.c:292
ret_from_fork+0x22/0x30 arch/x86/entry/entry_64.S:296
The mptcp_worker tries to update the MPTCP retransmission timer
even if such timer is not currently scheduled.
The mptcp_rtx_head() return value is bogus: we can have enqueued
data not yet transmitted. The above may additionally cause spurious,
unneeded MPTCP-level retransmissions.
Fix the issue adding an explicit clearing of the rtx queue before
trying to retransmit and checking for unacked data.
Additionally drop an unneeded timer stop call and the unused
mptcp_rtx_tail() helper.
Reported-by: Christoph Paasch <cpaasch@apple.com>
Fixes:
6e628cd3a8f7 ("mptcp: use mptcp release_cb for delayed tasks")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 11 Feb 2021 23:30:38 +0000 (15:30 -0800)]
mptcp: fix poll after shutdown
The current mptcp_poll() implementation gives unexpected
results after shutdown(SEND_SHUTDOWN) and when the msk
status is TCP_CLOSE.
Set the correct mask.
Fixes:
8edf08649eed ("mptcp: rework poll+nospace handling")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 11 Feb 2021 23:30:37 +0000 (15:30 -0800)]
mptcp: deliver ssk errors to msk
Currently all errors received on msk subflows are ignored.
We need to catch at least the errors on connect() and
on fallback sockets.
Use a custom sk_error_report callback at subflow level,
and do the real action under the msk socket lock - via
the usual sock_owned_by_user()/release_callback() schema.
Fixes:
6e628cd3a8f7 ("mptcp: use mptcp release_cb for delayed tasks")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Thu, 11 Feb 2021 21:32:52 +0000 (22:32 +0100)]
net: phy: consider that suspend2ram may cut off PHY power
Claudiu reported that on his system S2R cuts off power to the PHY and
after resuming certain PHY settings are lost. The PM folks confirmed
that cutting off power to selected components in S2R is a valid case.
Therefore resuming from S2R, same as from hibernation, has to assume
that the PHY has power-on defaults. As a consequence use the restore
callback also as resume callback.
In addition make sure that the interrupt configuration is restored.
Let's do this in phy_init_hw() and ensure that after this call
actual interrupt configuration is in sync with phydev->interrupts.
Currently, if interrupt was enabled before hibernation, we would
resume with interrupt disabled because that's the power-on default.
This fix applies cleanly only after the commit marked as fixed.
I don't have an affected system, therefore change is compile-tested
only.
[0] https://lore.kernel.org/netdev/
1610120754-14331-1-git-send-email-claudiu.beznea@microchip.com/
Fixes:
611d779af7ca ("net: phy: fix MDIO bus PM PHY resuming")
Reported-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Thu, 11 Feb 2021 19:51:22 +0000 (21:51 +0200)]
dpaa2-eth: fix memory leak in XDP_REDIRECT
If xdp_do_redirect() fails, the calling driver should handle recycling
or freeing of the page associated with the frame. The dpaa2-eth driver
didn't do either of them and just incremented a counter.
Fix this by trying to DMA map back the page and recycle it or, if the
mapping fails, just free it.
Fixes:
d678be1dc1ec ("dpaa2-eth: add XDP_REDIRECT support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tong Zhang [Thu, 11 Feb 2021 17:54:11 +0000 (12:54 -0500)]
enetc: auto select PHYLIB and MDIO_DEVRES
FSL_ENETC_MDIO use symbols from PHYLIB (MDIO_BUS) and MDIO_DEVRES,
however there are no dependency specified in Kconfig
ERROR: modpost: "__mdiobus_register" [drivers/net/ethernet/freescale/enetc/fsl-enetc-mdio.ko] undefined!
ERROR: modpost: "mdiobus_unregister" [drivers/net/ethernet/freescale/enetc/fsl-enetc-mdio.ko] undefined!
ERROR: modpost: "devm_mdiobus_alloc_size" [drivers/net/ethernet/freescale/enetc/fsl-enetc-mdio.ko] undefined!
add depends on MDIO_DEVRES && MDIO_BUS
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Rossi [Thu, 11 Feb 2021 05:17:57 +0000 (05:17 +0000)]
net: ethernet: aquantia: Handle error cleanup of start on open
The aq_nic_start function can fail in a variety of cases which leaves
the device in broken state.
An example case where the start function fails is the
request_threaded_irq which can be interrupted, resulting in a EINTR
result. This can be manually triggered by bringing the link up (e.g. ip
link set up) and triggering a SIGINT on the initiating process (e.g.
Ctrl+C). This would put the device into a half configured state.
Subsequently bringing the link up again would cause the napi_enable to
BUG.
In order to correctly clean up the failed attempt to start a device call
aq_nic_stop.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 11 Feb 2021 22:36:22 +0000 (14:36 -0800)]
Merge branch 'bnxt_en-fixes'
Michael Chan says:
====================
bnxt_en: 2 bug fixes.
Two unrelated fixes. The first one fixes intermittent false TX timeouts
during ring reconfigurations. The second one fixes a formatting
discrepancy between the stored and the running FW versions.
Please also queue these for -stable. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Thu, 11 Feb 2021 07:24:24 +0000 (02:24 -0500)]
bnxt_en: Fix devlink info's stored fw.psid version format.
The running fw.psid version is in decimal format but the stored
fw.psid is in hex format. This can mislead the user to reset the
NIC to activate the stored version to become the running version.
Fix it to display the stored fw.psid in decimal format.
Fixes:
1388875b3916 ("bnxt_en: Add stored FW version info to devlink info_get cb.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edwin Peer [Thu, 11 Feb 2021 07:24:23 +0000 (02:24 -0500)]
bnxt_en: reverse order of TX disable and carrier off
A TX queue can potentially immediately timeout after it is stopped
and the last TX timestamp on that queue was more than 5 seconds ago with
carrier still up. Prevent these intermittent false TX timeouts
by bringing down carrier first before calling netif_tx_disable().
Fixes:
c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sukadev Bhattiprolu [Thu, 11 Feb 2021 01:41:43 +0000 (17:41 -0800)]
ibmvnic: Set to CLOSED state even on error
If set_link_state() fails for any reason, we still cleanup the adapter
state and cannot recover from a partial close anyway. So set the adapter
to CLOSED state. That way if a new soft/hard reset is processed, the
adapter will remain in the CLOSED state until the next ibmvnic_open().
Fixes:
01d9bd792d16 ("ibmvnic: Reorganize device close")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reported-by: Abdul Haleem <abdhalee@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 10 Feb 2021 17:13:33 +0000 (09:13 -0800)]
tcp: fix tcp_rmem documentation
tcp_rmem[1] has been changed to 131072, we should update the documentation
to reflect this.
Fixes:
a337531b942b ("tcp: up initial rmem to 128KB and SYN rwin to around 64KB")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Zhibin Liu <zhibinliu@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 9 Feb 2021 20:34:09 +0000 (12:34 -0800)]
netdev-FAQ: answer some questions about the patchwork checks
Point out where patchwork bot's code lives, and that we don't want
people posting stuff that doesn't build.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Björn Töpel [Thu, 11 Feb 2021 08:20:29 +0000 (09:20 +0100)]
selftests/bpf: Convert test_xdp_redirect.sh to bash
The test_xdp_redirect.sh script uses a bash feature, '&>'. On systems,
e.g. Debian, where '/bin/sh' is dash, this will not work as
expected. Use bash in the shebang to get the expected behavior.
Further, using 'set -e' means that the error of a command cannot be
captured without the command being executed with '&&' or '||'. Let us
restructure the ping-commands, and use them as an if-expression, so
that we can capture the return value.
v4: Added missing Fixes:, and removed local variables. (Andrii)
v3: Reintroduced /bin/bash, and kept 'set -e'. (Andrii)
v2: Kept /bin/sh and removed bashisms. (Randy)
Fixes:
996139e801fd ("selftests: bpf: add a test for XDP redirect")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210211082029.1687666-1-bjorn.topel@gmail.com
wenxu [Tue, 9 Feb 2021 06:37:49 +0000 (14:37 +0800)]
net/sched: cls_flower: Reject invalid ct_state flags rules
Reject the unsupported and invalid ct_state flags of cls flower rules.
Fixes:
e0ace68af2ac ("net/sched: cls_flower: Add matching on conntrack info")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 10 Feb 2021 20:03:35 +0000 (12:03 -0800)]
Merge tag 'pm-5.11-rc8' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Address a performance regression related to scale-invariance on x86
that may prevent turbo CPU frequencies from being used in certain
workloads on systems using acpi-cpufreq as the CPU performance scaling
driver and schedutil as the scaling governor"
* tag 'pm-5.11-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: ACPI: Update arch scale-invariance max perf ratio if CPPC is not there
cpufreq: ACPI: Extend frequency tables to cover boost frequencies
Linus Torvalds [Wed, 10 Feb 2021 19:58:21 +0000 (11:58 -0800)]
Merge tag 'acpi-5.11-rc8' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Revert a problematic ACPICA commit that changed the code to attempt to
update memory regions which may be read-only on some systems (Ard
Biesheuvel)"
* tag 'acpi-5.11-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPICA: Interpreter: fix memory leak by using existing buffer"
Linus Torvalds [Wed, 10 Feb 2021 19:51:25 +0000 (11:51 -0800)]
Merge tag 'dmaengine-fix2-5.11' of git://git./linux/kernel/git/vkoul/dmaengine
Pull dmaengine fixes from Vinod Koul:
"Some late fixes for dmaengine:
Core:
- fix channel device_node deletion
Driver fixes:
- dw: revert of runtime pm enabling
- idxd: device state fix, interrupt completion and list corruption
- ti: resource leak
* tag 'dmaengine-fix2-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine dw: Revert "dmaengine: dw: Enable runtime PM"
dmaengine: idxd: check device state before issue command
dmaengine: ti: k3-udma: Fix a resource leak in an error handling path
dmaengine: move channel device_node deletion to driver
dmaengine: idxd: fix misc interrupt completion
dmaengine: idxd: Fix list corruption in description completion
Linus Torvalds [Wed, 10 Feb 2021 19:33:39 +0000 (11:33 -0800)]
Merge git://git./linux/kernel/git/netdev/net
Pull networking fixes from David Miller:
"Another pile of networing fixes:
1) ath9k build error fix from Arnd Bergmann
2) dma memory leak fix in mediatec driver from Lorenzo Bianconi.
3) bpf int3 kprobe fix from Alexei Starovoitov.
4) bpf stackmap integer overflow fix from Bui Quang Minh.
5) Add usb device ids for Cinterion MV31 to qmi_qwwan driver, from
Christoph Schemmel.
6) Don't update deleted entry in xt_recent netfilter module, from
Jazsef Kadlecsik.
7) Use after free in nftables, fix from Pablo Neira Ayuso.
8) Header checksum fix in flowtable from Sven Auhagen.
9) Validate user controlled length in qrtr code, from Sabyrzhan
Tasbolatov.
10) Fix race in xen/netback, from Juergen Gross,
11) New device ID in cxgb4, from Raju Rangoju.
12) Fix ring locking in rxrpc release call, from David Howells.
13) Don't return LAPB error codes from x25_open(), from Xie He.
14) Missing error returns in gsi_channel_setup() from Alex Elder.
15) Get skb_copy_and_csum_datagram working properly with odd segment
sizes, from Willem de Bruijn.
16) Missing RFS/RSS table init in enetc driver, from Vladimir Oltean.
17) Do teardown on probe failure in DSA, from Vladimir Oltean.
18) Fix compilation failures of txtimestamp selftest, from Vadim
Fedorenko.
19) Limit rx per-napi gro queue size to fix latency regression, from
Eric Dumazet.
20) dpaa_eth xdp fixes from Camelia Groza.
21) Missing txq mode update when switching CBS off, in stmmac driver,
from Mohammad Athari Bin Ismail.
22) Failover pending logic fix in ibmvnic driver, from Sukadev
Bhattiprolu.
23) Null deref fix in vmw_vsock, from Norbert Slusarek.
24) Missing verdict update in xdp paths of ena driver, from Shay
Agroskin.
25) seq_file iteration fix in sctp from Neil Brown.
26) bpf 32-bit src register truncation fix on div/mod, from Daniel
Borkmann.
27) Fix jmp32 pruning in bpf verifier, from Daniel Borkmann.
28) Fix locking in vsock_shutdown(), from Stefano Garzarella.
29) Various missing index bound checks in hns3 driver, from Yufeng Mo.
30) Flush ports on .phylink_mac_link_down() in dsa felix driver, from
Vladimir Oltean.
31) Don't mix up stp and mrp port states in bridge layer, from Horatiu
Vultur.
32) Fix locking during netif_tx_disable(), from Edwin Peer"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (45 commits)
bpf: Fix 32 bit src register truncation on div/mod
bpf: Fix verifier jmp32 pruning decision logic
bpf: Fix verifier jsgt branch analysis on max bound
vsock: fix locking in vsock_shutdown()
net: hns3: add a check for index in hclge_get_rss_key()
net: hns3: add a check for tqp_index in hclge_get_ring_chain_from_mbx()
net: hns3: add a check for queue_id in hclge_reset_vf_queue()
net: dsa: felix: implement port flushing on .phylink_mac_link_down
switchdev: mrp: Remove SWITCHDEV_ATTR_ID_MRP_PORT_STAT
bridge: mrp: Fix the usage of br_mrp_port_switchdev_set_state
net: watchdog: hold device global xmit lock during tx disable
netfilter: nftables: relax check for stateful expressions in set definition
netfilter: conntrack: skip identical origin tuple in same zone only
vsock/virtio: update credit only if socket is not closed
net: fix iteration for sctp transport seq_files
net: ena: Update XDP verdict upon failure
net/vmw_vsock: improve locking in vsock_connect_timeout()
net/vmw_vsock: fix NULL pointer dereference
ibmvnic: Clear failover_pending if unable to schedule
net: stmmac: set TxQ mode back to DCB after disabling CBS
...
Linus Torvalds [Wed, 10 Feb 2021 19:22:41 +0000 (11:22 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"14 patches.
Subsystems affected by this patch series: mm (kasan, mremap, tmpfs,
selftests, memcg, and slub), MAINTAINERS, squashfs, nilfs2, and
firmware"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
nilfs2: make splice write available again
mm, slub: better heuristic for number of cpus when calculating slab order
Revert "mm: memcontrol: avoid workload stalls when lowering memory.high"
MAINTAINERS: update Andrey Ryabinin's email address
selftests/vm: rename file run_vmtests to run_vmtests.sh
tmpfs: disallow CONFIG_TMPFS_INODE64 on alpha
tmpfs: disallow CONFIG_TMPFS_INODE64 on s390
mm/mremap: fix BUILD_BUG_ON() error in get_extent
firmware_loader: align .builtin_fw to 8
kasan: fix stack traces dependency for HW_TAGS
squashfs: add more sanity checks in xattr id lookup
squashfs: add more sanity checks in inode lookup
squashfs: add more sanity checks in id lookup
squashfs: avoid out of bounds writes in decompressors
Joachim Henke [Tue, 9 Feb 2021 21:42:36 +0000 (13:42 -0800)]
nilfs2: make splice write available again
Since 5.10, splice() or sendfile() to NILFS2 return EINVAL. This was
caused by commit
36e2c7421f02 ("fs: don't allow splice read/write
without explicit ops").
This patch initializes the splice_write field in file_operations, like
most file systems do, to restore the functionality.
Link: https://lkml.kernel.org/r/1612784101-14353-1-git-send-email-konishi.ryusuke@gmail.com
Signed-off-by: Joachim Henke <joachim.henke@t-systems.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org> [5.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vlastimil Babka [Tue, 9 Feb 2021 21:42:32 +0000 (13:42 -0800)]
mm, slub: better heuristic for number of cpus when calculating slab order
When creating a new kmem cache, SLUB determines how large the slab pages
will based on number of inputs, including the number of CPUs in the
system. Larger slab pages mean that more objects can be allocated/free
from per-cpu slabs before accessing shared structures, but also
potentially more memory can be wasted due to low slab usage and
fragmentation. The rough idea of using number of CPUs is that larger
systems will be more likely to benefit from reduced contention, and also
should have enough memory to spare.
Number of CPUs used to be determined as nr_cpu_ids, which is number of
possible cpus, but on some systems many will never be onlined, thus
commit
045ab8c9487b ("mm/slub: let number of online CPUs determine the
slub page order") changed it to nr_online_cpus(). However, for kmem
caches created early before CPUs are onlined, this may lead to
permamently low slab page sizes.
Vincent reports a regression [1] of hackbench on arm64 systems:
"I'm facing significant performances regression on a large arm64
server system (224 CPUs). Regressions is also present on small arm64
system (8 CPUs) but in a far smaller order of magnitude
On 224 CPUs system : 9 iterations of hackbench -l 16000 -g 16
v5.11-rc4 : 9.135sec (+/- 0.45%)
v5.11-rc4 + revert this patch: 3.173sec (+/- 0.48%)
v5.10: 3.136sec (+/- 0.40%)"
Mel reports a regression [2] of hackbench on x86_64, with lockstat suggesting
page allocator contention:
"i.e. the patch incurs a 7% to 32% performance penalty. This bisected
cleanly yesterday when I was looking for the regression and then
found the thread.
Numerous caches change size. For example, kmalloc-512 goes from
order-0 (vanilla) to order-2 with the revert.
So mostly this is down to the number of times SLUB calls into the
page allocator which only caches order-0 pages on a per-cpu basis"
Clearly num_online_cpus() doesn't work too early in bootup. We could
change the order dynamically in a memory hotplug callback, but runtime
order changing for existing kmem caches has been already shown as
dangerous, and removed in
32a6f409b693 ("mm, slub: remove runtime
allocation order changes").
It could be resurrected in a safe manner with some effort, but to fix
the regression we need something simpler.
We could use num_present_cpus() that should be the number of physically
present CPUs even before they are onlined. That would work for PowerPC
[3], which triggered the original commit, but that still doesn't work on
arm64 [4] as explained in [5].
So this patch tries to determine the best available value without
specific arch knowledge.
- num_present_cpus() if the number is larger than 1, as that means the
arch is likely setting it properly
- nr_cpu_ids otherwise
This should fix the reported regressions while also keeping the effect
of
045ab8c9487b for PowerPC systems. It's possible there are
configurations where num_present_cpus() is 1 during boot while
nr_cpu_ids is at the same time bloated, so these (if they exist) would
keep the large orders based on nr_cpu_ids as was before
045ab8c9487b.
[1] https://lore.kernel.org/linux-mm/CAKfTPtA_JgMf_+zdFbcb_V9rM7JBWNPjAz9irgwFj7Rou=xzZg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mm/
20210128134512.GF3592@techsingularity.net/
[3] https://lore.kernel.org/linux-mm/
20210123051607.GC2587010@in.ibm.com/
[4] https://lore.kernel.org/linux-mm/CAKfTPtAjyVmS5VYvU6DBxg4-JEo5bdmWbngf-03YsY18cmWv_g@mail.gmail.com/
[5] https://lore.kernel.org/linux-mm/
20210126230305.GD30941@willie-the-truck/
Link: https://lkml.kernel.org/r/20210208134108.22286-1-vbabka@suse.cz
Fixes:
045ab8c9487b ("mm/slub: let number of online CPUs determine the slub page order")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Vincent Guittot <vincent.guittot@linaro.org>
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Tested-by: Mel Gorman <mgorman@techsingularity.net>
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Jann Horn <jannh@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Wed, 10 Feb 2021 02:55:17 +0000 (18:55 -0800)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2021-02-10
The following pull-request contains BPF updates for your *net* tree.
We've added 5 non-merge commits during the last 8 day(s) which contain
a total of 3 files changed, 22 insertions(+), 21 deletions(-).
The main changes are:
1) Fix missed execution of kprobes BPF progs when kprobe is firing via
int3, from Alexei Starovoitov.
2) Fix potential integer overflow in map max_entries for stackmap on
32 bit archs, from Bui Quang Minh.
3) Fix a verifier pruning and a insn rewrite issue related to 32 bit ops,
from Daniel Borkmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
c# Please enter a commit message to explain why this merge is necessary,
Johannes Weiner [Tue, 9 Feb 2021 21:42:28 +0000 (13:42 -0800)]
Revert "mm: memcontrol: avoid workload stalls when lowering memory.high"
This reverts commit
536d3bf261a2fc3b05b3e91e7eef7383443015cf, as it can
cause writers to memory.high to get stuck in the kernel forever,
performing page reclaim and consuming excessive amounts of CPU cycles.
Before the patch, a write to memory.high would first put the new limit
in place for the workload, and then reclaim the requested delta. After
the patch, the kernel tries to reclaim the delta before putting the new
limit into place, in order to not overwhelm the workload with a sudden,
large excess over the limit. However, if reclaim is actively racing
with new allocations from the uncurbed workload, it can keep the write()
working inside the kernel indefinitely.
This is causing problems in Facebook production. A privileged
system-level daemon that adjusts memory.high for various workloads
running on a host can get unexpectedly stuck in the kernel and
essentially turn into a sort of involuntary kswapd for one of the
workloads. We've observed that daemon busy-spin in a write() for
minutes at a time, neglecting its other duties on the system, and
expending privileged system resources on behalf of a workload.
To remedy this, we have first considered changing the reclaim logic to
break out after a couple of loops - whether the workload has converged
to the new limit or not - and bound the write() call this way. However,
the root cause that inspired the sequence change in the first place has
been fixed through other means, and so a revert back to the proven
limit-setting sequence, also used by memory.max, is preferable.
The sequence was changed to avoid extreme latencies in the workload when
the limit was lowered: the sudden, large excess created by the limit
lowering would erroneously trigger the penalty sleeping code that is
meant to throttle excessive growth from below. Allocating threads could
end up sleeping long after the write() had already reclaimed the delta
for which they were being punished.
However, erroneous throttling also caused problems in other scenarios at
around the same time. This resulted in commit
b3ff92916af3 ("mm, memcg:
reclaim more aggressively before high allocator throttling"), included
in the same release as the offending commit. When allocating threads
now encounter large excess caused by a racing write() to memory.high,
instead of entering punitive sleeps, they will simply be tasked with
helping reclaim down the excess, and will be held no longer than it
takes to accomplish that. This is in line with regular limit
enforcement - i.e. if the workload allocates up against or over an
otherwise unchanged limit from below.
With the patch breaking userspace, and the root cause addressed by other
means already, revert it again.
Link: https://lkml.kernel.org/r/20210122184341.292461-1-hannes@cmpxchg.org
Fixes:
536d3bf261a2 ("mm: memcontrol: avoid workload stalls when lowering memory.high")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Tejun Heo <tj@kernel.org>
Acked-by: Chris Down <chris@chrisdown.name>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Michal Koutný <mkoutny@suse.com>
Cc: <stable@vger.kernel.org> [5.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Tue, 9 Feb 2021 21:42:24 +0000 (13:42 -0800)]
MAINTAINERS: update Andrey Ryabinin's email address
Update my email, @virtuozzo.com will stop working shortly.
Link: https://lkml.kernel.org/r/20210204223904.3824-1-ryabinin.a.a@gmail.com
Signed-off-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rong Chen [Tue, 9 Feb 2021 21:42:21 +0000 (13:42 -0800)]
selftests/vm: rename file run_vmtests to run_vmtests.sh
Commit
c2aa8afc36fa has renamed run_vmtests in Makefile, but the file
still uses the old name.
The kernel test robot reported the following issue:
# selftests: vm: run_vmtests.sh
# Warning: file run_vmtests.sh is missing!
not ok 1 selftests: vm: run_vmtests.sh
Link: https://lkml.kernel.org/r/20210205085507.1479894-1-rong.a.chen@intel.com
Fixes:
c2aa8afc36fa (selftests/vm: rename run_vmtests --> run_vmtests.sh)
Signed-off-by: Rong Chen <rong.a.chen@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Seth Forshee [Tue, 9 Feb 2021 21:42:17 +0000 (13:42 -0800)]
tmpfs: disallow CONFIG_TMPFS_INODE64 on alpha
As with s390, alpha is a 64-bit architecture with a 32-bit ino_t. With
CONFIG_TMPFS_INODE64=y tmpfs mounts will get 64-bit inode numbers and
display "inode64" in the mount options, whereas passing "inode64" in the
mount options will fail. This leads to erroneous behaviours such as
this:
# mkdir mnt
# mount -t tmpfs nodev mnt
# mount -o remount,rw mnt
mount: /home/ubuntu/mnt: mount point not mounted or bad option.
Prevent CONFIG_TMPFS_INODE64 from being selected on alpha.
Link: https://lkml.kernel.org/r/20210208215726.608197-1-seth.forshee@canonical.com
Fixes:
ea3271f7196c ("tmpfs: support 64-bit inums per-sb")
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Chris Down <chris@chrisdown.name>
Cc: Amir Goldstein <amir73il@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: <stable@vger.kernel.org> [5.9+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Seth Forshee [Tue, 9 Feb 2021 21:42:14 +0000 (13:42 -0800)]
tmpfs: disallow CONFIG_TMPFS_INODE64 on s390
Currently there is an assumption in tmpfs that 64-bit architectures also
have a 64-bit ino_t. This is not true on s390 which has a 32-bit ino_t.
With CONFIG_TMPFS_INODE64=y tmpfs mounts will get 64-bit inode numbers
and display "inode64" in the mount options, but passing the "inode64"
mount option will fail. This leads to the following behavior:
# mkdir mnt
# mount -t tmpfs nodev mnt
# mount -o remount,rw mnt
mount: /home/ubuntu/mnt: mount point not mounted or bad option.
As mount sees "inode64" in the mount options and thus passes it in the
options for the remount.
So prevent CONFIG_TMPFS_INODE64 from being selected on s390.
Link: https://lkml.kernel.org/r/20210205230620.518245-1-seth.forshee@canonical.com
Fixes:
ea3271f7196c ("tmpfs: support 64-bit inums per-sb")
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Chris Down <chris@chrisdown.name>
Cc: Hugh Dickins <hughd@google.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: <stable@vger.kernel.org> [5.9+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Tue, 9 Feb 2021 21:42:10 +0000 (13:42 -0800)]
mm/mremap: fix BUILD_BUG_ON() error in get_extent
clang can't evaluate this function argument at compile time when the
function is not inlined, which leads to a link time failure:
ld.lld: error: undefined symbol: __compiletime_assert_414
>>> referenced by mremap.c
>>> mremap.o:(get_extent) in archive mm/built-in.a
Mark the function as __always_inline to avoid it.
Link: https://lkml.kernel.org/r/20201230154104.522605-1-arnd@kernel.org
Fixes:
9ad9718bfa41 ("mm/mremap: calculate extent in one place")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Brian Geffon <bgeffon@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fangrui Song [Tue, 9 Feb 2021 21:42:07 +0000 (13:42 -0800)]
firmware_loader: align .builtin_fw to 8
arm64 references the start address of .builtin_fw (__start_builtin_fw)
with a pair of R_AARCH64_ADR_PREL_PG_HI21/R_AARCH64_LDST64_ABS_LO12_NC
relocations. The compiler is allowed to emit the
R_AARCH64_LDST64_ABS_LO12_NC relocation because struct builtin_fw in
include/linux/firmware.h is 8-byte aligned.
The R_AARCH64_LDST64_ABS_LO12_NC relocation requires the address to be a
multiple of 8, which may not be the case if .builtin_fw is empty.
Unconditionally align .builtin_fw to fix the linker error. 32-bit
architectures could use ALIGN(4) but that would add unnecessary
complexity, so just use ALIGN(8).
Link: https://lkml.kernel.org/r/20201208054646.2913063-1-maskray@google.com
Link: https://github.com/ClangBuiltLinux/linux/issues/1204
Fixes:
5658c76 ("firmware: allow firmware files to be built into kernel image")
Signed-off-by: Fangrui Song <maskray@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Tue, 9 Feb 2021 21:42:03 +0000 (13:42 -0800)]
kasan: fix stack traces dependency for HW_TAGS
Currently, whether the alloc/free stack traces collection is enabled by
default for hardware tag-based KASAN depends on CONFIG_DEBUG_KERNEL.
The intention for this dependency was to only enable collection on slow
debug kernels due to a significant perf and memory impact.
As it turns out, CONFIG_DEBUG_KERNEL is not considered a debug option
and is enabled on many productions kernels including Android and Ubuntu.
As the result, this dependency is pointless and only complicates the
code and documentation.
Having stack traces collection disabled by default would make the
hardware mode work differently to to the software ones, which is
confusing.
This change removes the dependency and enables stack traces collection
by default.
Looking into the future, this default might makes sense for production
kernels, assuming we implement a fast stack trace collection approach.
Link: https://lkml.kernel.org/r/6678d77ceffb71f1cff2cf61560e2ffe7bb6bfe9.1612808820.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Marco Elver <elver@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Branislav Rankov <Branislav.Rankov@arm.com>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Phillip Lougher [Tue, 9 Feb 2021 21:42:00 +0000 (13:42 -0800)]
squashfs: add more sanity checks in xattr id lookup
Sysbot has reported a warning where a kmalloc() attempt exceeds the
maximum limit. This has been identified as corruption of the xattr_ids
count when reading the xattr id lookup table.
This patch adds a number of additional sanity checks to detect this
corruption and others.
1. It checks for a corrupted xattr index read from the inode. This could
be because the metadata block is uncompressed, or because the
"compression" bit has been corrupted (turning a compressed block
into an uncompressed block). This would cause an out of bounds read.
2. It checks against corruption of the xattr_ids count. This can either
lead to the above kmalloc failure, or a smaller than expected
table to be read.
3. It checks the contents of the index table for corruption.
[phillip@squashfs.org.uk: fix checkpatch issue]
Link: https://lkml.kernel.org/r/270245655.754655.1612770082682@webmail.123-reg.co.uk
Link: https://lkml.kernel.org/r/20210204130249.4495-5-phillip@squashfs.org.uk
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Reported-by: syzbot+2ccea6339d368360800d@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Phillip Lougher [Tue, 9 Feb 2021 21:41:56 +0000 (13:41 -0800)]
squashfs: add more sanity checks in inode lookup
Sysbot has reported an "slab-out-of-bounds read" error which has been
identified as being caused by a corrupted "ino_num" value read from the
inode. This could be because the metadata block is uncompressed, or
because the "compression" bit has been corrupted (turning a compressed
block into an uncompressed block).
This patch adds additional sanity checks to detect this, and the
following corruption.
1. It checks against corruption of the inodes count. This can either
lead to a larger table to be read, or a smaller than expected
table to be read.
In the case of a too large inodes count, this would often have been
trapped by the existing sanity checks, but this patch introduces
a more exact check, which can identify too small values.
2. It checks the contents of the index table for corruption.
[phillip@squashfs.org.uk: fix checkpatch issue]
Link: https://lkml.kernel.org/r/527909353.754618.1612769948607@webmail.123-reg.co.uk
Link: https://lkml.kernel.org/r/20210204130249.4495-4-phillip@squashfs.org.uk
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Reported-by: syzbot+04419e3ff19d2970ea28@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Phillip Lougher [Tue, 9 Feb 2021 21:41:53 +0000 (13:41 -0800)]
squashfs: add more sanity checks in id lookup
Sysbot has reported a number of "slab-out-of-bounds reads" and
"use-after-free read" errors which has been identified as being caused
by a corrupted index value read from the inode. This could be because
the metadata block is uncompressed, or because the "compression" bit has
been corrupted (turning a compressed block into an uncompressed block).
This patch adds additional sanity checks to detect this, and the
following corruption.
1. It checks against corruption of the ids count. This can either
lead to a larger table to be read, or a smaller than expected
table to be read.
In the case of a too large ids count, this would often have been
trapped by the existing sanity checks, but this patch introduces
a more exact check, which can identify too small values.
2. It checks the contents of the index table for corruption.
Link: https://lkml.kernel.org/r/20210204130249.4495-3-phillip@squashfs.org.uk
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Reported-by: syzbot+b06d57ba83f604522af2@syzkaller.appspotmail.com
Reported-by: syzbot+c021ba012da41ee9807c@syzkaller.appspotmail.com
Reported-by: syzbot+5024636e8b5fd19f0f19@syzkaller.appspotmail.com
Reported-by: syzbot+bcbc661df46657d0fa4f@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Phillip Lougher [Tue, 9 Feb 2021 21:41:50 +0000 (13:41 -0800)]
squashfs: avoid out of bounds writes in decompressors
Patch series "Squashfs: fix BIO migration regression and add sanity checks".
Patch [1/4] fixes a regression introduced by the "migrate from
ll_rw_block usage to BIO" patch, which has produced a number of
Sysbot/Syzkaller reports.
Patches [2/4], [3/4], and [4/4] fix a number of filesystem corruption
issues which have produced Sysbot reports in the id, inode and xattr
lookup code.
Each patch has been tested against the Sysbot reproducers using the
given kernel configuration. They have the appropriate "Reported-by:"
lines added.
Additionally, all of the reproducer filesystems are indirectly fixed by
patch [4/4] due to the fact they all have xattr corruption which is now
detected there.
Additional testing with other configurations and architectures (32bit,
big endian), and normal filesystems has also been done to trap any
inadvertent regressions caused by the additional sanity checks.
This patch (of 4):
This is a regression introduced by the patch "migrate from ll_rw_block
usage to BIO".
Sysbot/Syskaller has reported a number of "out of bounds writes" and
"unable to handle kernel paging request in squashfs_decompress" errors
which have been identified as a regression introduced by the above
patch.
Specifically, the patch removed the following sanity check
if (length < 0 || length > output->length ||
(index + length) > msblk->bytes_used)
This check did two things:
1. It ensured any reads were not beyond the end of the filesystem
2. It ensured that the "length" field read from the filesystem
was within the expected maximum length. Without this any
corrupted values can over-run allocated buffers.
Link: https://lkml.kernel.org/r/20210204130249.4495-1-phillip@squashfs.org.uk
Link: https://lkml.kernel.org/r/20210204130249.4495-2-phillip@squashfs.org.uk
Fixes:
93e72b3c612adc ("squashfs: migrate from ll_rw_block usage to BIO")
Reported-by: syzbot+6fba78f99b9afd4b5634@syzkaller.appspotmail.com
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Cc: Philippe Liard <pliard@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 10 Feb 2021 01:19:56 +0000 (17:19 -0800)]
Merge tag 'i3c/fixes-for-5.11' of git://git./linux/kernel/git/i3c/linux
Pull i3c fix from Alexandre Belloni:
"A single build warning fix"
* tag 'i3c/fixes-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c/master/mipi-i3c-hci: Fix position of __maybe_unused in i3c_hci_of_match
Daniel Borkmann [Tue, 9 Feb 2021 18:46:10 +0000 (18:46 +0000)]
bpf: Fix 32 bit src register truncation on div/mod
While reviewing a different fix, John and I noticed an oddity in one of the
BPF program dumps that stood out, for example:
# bpftool p d x i 13
0: (b7) r0 =
808464450
1: (b4) w4 =
808464432
2: (bc) w0 = w0
3: (15) if r0 == 0x0 goto pc+1
4: (9c) w4 %= w0
[...]
In line 2 we noticed that the mov32 would 32 bit truncate the original src
register for the div/mod operation. While for the two operations the dst
register is typically marked unknown e.g. from adjust_scalar_min_max_vals()
the src register is not, and thus verifier keeps tracking original bounds,
simplified:
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (b7) r0 = -1
1: R0_w=invP-1 R1=ctx(id=0,off=0,imm=0) R10=fp0
1: (b7) r1 = -1
2: R0_w=invP-1 R1_w=invP-1 R10=fp0
2: (3c) w0 /= w1
3: R0_w=invP(id=0,umax_value=
4294967295,var_off=(0x0; 0xffffffff)) R1_w=invP-1 R10=fp0
3: (77) r1 >>= 32
4: R0_w=invP(id=0,umax_value=
4294967295,var_off=(0x0; 0xffffffff)) R1_w=invP4294967295 R10=fp0
4: (bf) r0 = r1
5: R0_w=invP4294967295 R1_w=invP4294967295 R10=fp0
5: (95) exit
processed 6 insns (limit
1000000) max_states_per_insn 0 total_states 0 peak_states 0 mark_read 0
Runtime result of r0 at exit is 0 instead of expected -1. Remove the
verifier mov32 src rewrite in div/mod and replace it with a jmp32 test
instead. After the fix, we result in the following code generation when
having dividend r1 and divisor r6:
div, 64 bit: div, 32 bit:
0: (b7) r6 = 8 0: (b7) r6 = 8
1: (b7) r1 = 8 1: (b7) r1 = 8
2: (55) if r6 != 0x0 goto pc+2 2: (56) if w6 != 0x0 goto pc+2
3: (ac) w1 ^= w1 3: (ac) w1 ^= w1
4: (05) goto pc+1 4: (05) goto pc+1
5: (3f) r1 /= r6 5: (3c) w1 /= w6
6: (b7) r0 = 0 6: (b7) r0 = 0
7: (95) exit 7: (95) exit
mod, 64 bit: mod, 32 bit:
0: (b7) r6 = 8 0: (b7) r6 = 8
1: (b7) r1 = 8 1: (b7) r1 = 8
2: (15) if r6 == 0x0 goto pc+1 2: (16) if w6 == 0x0 goto pc+1
3: (9f) r1 %= r6 3: (9c) w1 %= w6
4: (b7) r0 = 0 4: (b7) r0 = 0
5: (95) exit 5: (95) exit
x86 in particular can throw a 'divide error' exception for div
instruction not only for divisor being zero, but also for the case
when the quotient is too large for the designated register. For the
edx:eax and rdx:rax dividend pair it is not an issue in x86 BPF JIT
since we always zero edx (rdx). Hence really the only protection
needed is against divisor being zero.
Fixes:
68fda450a7df ("bpf: fix 32-bit divide by zero")
Co-developed-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann [Fri, 5 Feb 2021 19:48:21 +0000 (20:48 +0100)]
bpf: Fix verifier jmp32 pruning decision logic
Anatoly has been fuzzing with kBdysch harness and reported a hang in
one of the outcomes:
func#0 @0
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (b7) r0 =
808464450
1: R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R10=fp0
1: (b4) w4 =
808464432
2: R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R4_w=invP808464432 R10=fp0
2: (9c) w4 %= w0
3: R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umax_value=
4294967295,var_off=(0x0; 0xffffffff)) R10=fp0
3: (66) if w4 s> 0x30303030 goto pc+0
R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umax_value=
4294967295,var_off=(0x0; 0xffffffff),s32_max_value=
808464432) R10=fp0
4: R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umax_value=
4294967295,var_off=(0x0; 0xffffffff),s32_max_value=
808464432) R10=fp0
4: (7f) r0 >>= r0
5: R0_w=invP(id=0) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umax_value=
4294967295,var_off=(0x0; 0xffffffff),s32_max_value=
808464432) R10=fp0
5: (9c) w4 %= w0
6: R0_w=invP(id=0) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
6: (66) if w0 s> 0x3030 goto pc+0
R0_w=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
7: R0=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4=invP(id=0) R10=fp0
7: (d6) if w0 s<= 0x303030 goto pc+1
9: R0=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4=invP(id=0) R10=fp0
9: (95) exit
propagating r0
from 6 to 7: safe
4: R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umin_value=
808464433,umax_value=
2147483647,var_off=(0x0; 0x7fffffff)) R10=fp0
4: (7f) r0 >>= r0
5: R0_w=invP(id=0) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umin_value=
808464433,umax_value=
2147483647,var_off=(0x0; 0x7fffffff)) R10=fp0
5: (9c) w4 %= w0
6: R0_w=invP(id=0) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
6: (66) if w0 s> 0x3030 goto pc+0
R0_w=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
propagating r0
7: safe
propagating r0
from 6 to 7: safe
processed 15 insns (limit
1000000) max_states_per_insn 0 total_states 1 peak_states 1 mark_read 1
The underlying program was xlated as follows:
# bpftool p d x i 10
0: (b7) r0 =
808464450
1: (b4) w4 =
808464432
2: (bc) w0 = w0
3: (15) if r0 == 0x0 goto pc+1
4: (9c) w4 %= w0
5: (66) if w4 s> 0x30303030 goto pc+0
6: (7f) r0 >>= r0
7: (bc) w0 = w0
8: (15) if r0 == 0x0 goto pc+1
9: (9c) w4 %= w0
10: (66) if w0 s> 0x3030 goto pc+0
11: (d6) if w0 s<= 0x303030 goto pc+1
12: (05) goto pc-1
13: (95) exit
The verifier rewrote original instructions it recognized as dead code with
'goto pc-1', but reality differs from verifier simulation in that we are
actually able to trigger a hang due to hitting the 'goto pc-1' instructions.
Taking a closer look at the verifier analysis, the reason is that it misjudges
its pruning decision at the first 'from 6 to 7: safe' occasion. What happens
is that while both old/cur registers are marked as precise, they get misjudged
for the jmp32 case as range_within() yields true, meaning that the prior
verification path with a wider register bound could be verified successfully
and therefore the current path with a narrower register bound is deemed safe
as well whereas in reality it's not. R0 old/cur path's bounds compare as
follows:
old: smin_value=0x8000000000000000,smax_value=0x7fffffffffffffff,umin_value=0x0,umax_value=0xffffffffffffffff,var_off=(0x0; 0xffffffffffffffff)
cur: smin_value=0x8000000000000000,smax_value=0x7fffffff7fffffff,umin_value=0x0,umax_value=0xffffffff7fffffff,var_off=(0x0; 0xffffffff7fffffff)
old: s32_min_value=0x80000000,s32_max_value=0x00003030,u32_min_value=0x00000000,u32_max_value=0xffffffff
cur: s32_min_value=0x00003031,s32_max_value=0x7fffffff,u32_min_value=0x00003031,u32_max_value=0x7fffffff
The 64 bit bounds generally look okay and while the information that got
propagated from 32 to 64 bit looks correct as well, it's not precise enough
for judging a conditional jmp32. Given the latter only operates on subregisters
we also need to take these into account as well for a range_within() probe
in order to be able to prune paths. Extending the range_within() constraint
to both bounds will be able to tell us that the old signed 32 bit bounds are
not wider than the cur signed 32 bit bounds.
With the fix in place, the program will now verify the 'goto' branch case as
it should have been:
[...]
6: R0_w=invP(id=0) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
6: (66) if w0 s> 0x3030 goto pc+0
R0_w=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
7: R0=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4=invP(id=0) R10=fp0
7: (d6) if w0 s<= 0x303030 goto pc+1
9: R0=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4=invP(id=0) R10=fp0
9: (95) exit
7: R0_w=invP(id=0,smax_value=
9223372034707292159,umax_value=
18446744071562067967,var_off=(0x0; 0xffffffff7fffffff),s32_min_value=12337,u32_min_value=12337,u32_max_value=
2147483647) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
7: (d6) if w0 s<= 0x303030 goto pc+1
R0_w=invP(id=0,smax_value=
9223372034707292159,umax_value=
18446744071562067967,var_off=(0x0; 0xffffffff7fffffff),s32_min_value=
3158065,u32_min_value=
3158065,u32_max_value=
2147483647) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
8: R0_w=invP(id=0,smax_value=
9223372034707292159,umax_value=
18446744071562067967,var_off=(0x0; 0xffffffff7fffffff),s32_min_value=
3158065,u32_min_value=
3158065,u32_max_value=
2147483647) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
8: (30) r0 = *(u8 *)skb[
808464432]
BPF_LD_[ABS|IND] uses reserved fields
processed 11 insns (limit
1000000) max_states_per_insn 1 total_states 1 peak_states 1 mark_read 1
The bug is quite subtle in the sense that when verifier would determine that
a given branch is dead code, it would (here: wrongly) remove these instructions
from the program and hard-wire the taken branch for privileged programs instead
of the 'goto pc-1' rewrites which will cause hard to debug problems.
Fixes:
3f50f132d840 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann [Fri, 5 Feb 2021 16:20:14 +0000 (17:20 +0100)]
bpf: Fix verifier jsgt branch analysis on max bound
Fix incorrect is_branch{32,64}_taken() analysis for the jsgt case. The return
code for both will tell the caller whether a given conditional jump is taken
or not, e.g. 1 means branch will be taken [for the involved registers] and the
goto target will be executed, 0 means branch will not be taken and instead we
fall-through to the next insn, and last but not least a -1 denotes that it is
not known at verification time whether a branch will be taken or not. Now while
the jsgt has the branch-taken case correct with reg->s32_min_value > sval, the
branch-not-taken case is off-by-one when testing for reg->s32_max_value < sval
since the branch will also be taken for reg->s32_max_value == sval. The jgt
branch analysis, for example, gets this right.
Fixes:
3f50f132d840 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Fixes:
4f7b3e82589e ("bpf: improve verifier branch analysis")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
David S. Miller [Tue, 9 Feb 2021 23:55:59 +0000 (15:55 -0800)]
Merge git://git./pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) nf_conntrack_tuple_taken() needs to recheck zone for
NAT clash resolution, from Florian Westphal.
2) Restore support for stateful expressions when set definition
specifies no stateful expressions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Tue, 9 Feb 2021 08:52:19 +0000 (09:52 +0100)]
vsock: fix locking in vsock_shutdown()
In vsock_shutdown() we touched some socket fields without holding the
socket lock, such as 'state' and 'sk_flags'.
Also, after the introduction of multi-transport, we are accessing
'vsk->transport' in vsock_send_shutdown() without holding the lock
and this call can be made while the connection is in progress, so
the transport can change in the meantime.
To avoid issues, we hold the socket lock when we enter in
vsock_shutdown() and release it when we leave.
Among the transports that implement the 'shutdown' callback, only
hyperv_transport acquired the lock. Since the caller now holds it,
we no longer take it.
Fixes:
d021c344051a ("VSOCK: Introduce VM Sockets")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 9 Feb 2021 23:20:43 +0000 (15:20 -0800)]
Merge branch 'hns3-fixes'
Huazhong Tan says:
====================
net: hns3: fixes for -net
The parameters sent from vf may be unreliable. If these
parameters are used directly, memory overwriting may occur.
So this series adds some checks for this case.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Tue, 9 Feb 2021 09:03:07 +0000 (17:03 +0800)]
net: hns3: add a check for index in hclge_get_rss_key()
The index is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this index before using it in hclge_get_rss_key().
Fixes:
a638b1d8cc87 ("net: hns3: fix get VF RSS issue")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Tue, 9 Feb 2021 09:03:06 +0000 (17:03 +0800)]
net: hns3: add a check for tqp_index in hclge_get_ring_chain_from_mbx()
The tqp_index is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this tqp_index before using it in hclge_get_ring_chain_from_mbx().
Fixes:
84e095d64ed9 ("net: hns3: Change PF to add ring-vect binding & resetQ to mailbox")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Tue, 9 Feb 2021 09:03:05 +0000 (17:03 +0800)]
net: hns3: add a check for queue_id in hclge_reset_vf_queue()
The queue_id is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this queue_id before using it in hclge_reset_vf_queue().
Fixes:
1a426f8b40fc ("net: hns3: fix the VF queue reset flow error")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 8 Feb 2021 17:36:27 +0000 (19:36 +0200)]
net: dsa: felix: implement port flushing on .phylink_mac_link_down
There are several issues which may be seen when the link goes down while
forwarding traffic, all of which can be attributed to the fact that the
port flushing procedure from the reference manual was not closely
followed.
With flow control enabled on both the ingress port and the egress port,
it may happen when a link goes down that Ethernet packets are in flight.
In flow control mode, frames are held back and not dropped. When there
is enough traffic in flight (example: iperf3 TCP), then the ingress port
might enter congestion and never exit that state. This is a problem,
because it is the egress port's link that went down, and that has caused
the inability of the ingress port to send packets to any other port.
This is solved by flushing the egress port's queues when it goes down.
There is also a problem when performing stream splitting for
IEEE 802.1CB traffic (not yet upstream, but a sort of multicast,
basically). There, if one port from the destination ports mask goes
down, splitting the stream towards the other destinations will no longer
be performed. This can be traced down to this line:
ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);
which should have been instead, as per the reference manual:
ocelot_port_rmwl(ocelot_port, 0, DEV_MAC_ENA_CFG_RX_ENA,
DEV_MAC_ENA_CFG);
Basically only DEV_MAC_ENA_CFG_RX_ENA should be disabled, but not
DEV_MAC_ENA_CFG_TX_ENA - I don't have further insight into why that is
the case, but apparently multicasting to several ports will cause issues
if at least one of them doesn't have DEV_MAC_ENA_CFG_TX_ENA set.
I am not sure what the state of the Ocelot VSC7514 driver is, but
probably not as bad as Felix/Seville, since VSC7514 uses phylib and has
the following in ocelot_adjust_link:
if (!phydev->link)
return;
therefore the port is not really put down when the link is lost, unlike
the DSA drivers which use .phylink_mac_link_down for that.
Nonetheless, I put ocelot_port_flush() in the common ocelot.c because it
needs to access some registers from drivers/net/ethernet/mscc/ocelot_rew.h
which are not exported in include/soc/mscc/ and a bugfix patch should
probably not move headers around.
Fixes:
bdeced75b13f ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 9 Feb 2021 00:20:58 +0000 (16:20 -0800)]
Merge branch 'bridge-mrp'
Horatiu Vultur says:
====================
bridge: mrp: Fix br_mrp_port_switchdev_set_state
Based on the discussion here[1], there was a problem with the function
br_mrp_port_switchdev_set_state. The problem was that it was called
both with BR_STATE* and BR_MRP_PORT_STATE* types. This patch series
fixes this issue and removes SWITCHDEV_ATTR_ID_MRP_PORT_STAT because
is not used anymore.
[1] https://www.spinics.net/lists/netdev/msg714816.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Sat, 6 Feb 2021 21:47:34 +0000 (22:47 +0100)]
switchdev: mrp: Remove SWITCHDEV_ATTR_ID_MRP_PORT_STAT
Now that MRP started to use also SWITCHDEV_ATTR_ID_PORT_STP_STATE to
notify HW, then SWITCHDEV_ATTR_ID_MRP_PORT_STAT is not used anywhere
else, therefore we can remove it.
Fixes:
c284b545900830 ("switchdev: mrp: Extend switchdev API to offload MRP")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Sat, 6 Feb 2021 21:47:33 +0000 (22:47 +0100)]
bridge: mrp: Fix the usage of br_mrp_port_switchdev_set_state
The function br_mrp_port_switchdev_set_state was called both with MRP
port state and STP port state, which is an issue because they don't
match exactly.
Therefore, update the function to be used only with STP port state and
use the id SWITCHDEV_ATTR_ID_PORT_STP_STATE.
The choice of using STP over MRP is that the drivers already implement
SWITCHDEV_ATTR_ID_PORT_STP_STATE and already in SW we update the port
STP state.
Fixes:
9a9f26e8f7ea30 ("bridge: mrp: Connect MRP API with the switchdev API")
Fixes:
fadd409136f0f2 ("bridge: switchdev: mrp: Implement MRP API for switchdev")
Fixes:
2f1a11ae11d222 ("bridge: mrp: Add MRP interface.")
Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edwin Peer [Sat, 6 Feb 2021 01:37:32 +0000 (17:37 -0800)]
net: watchdog: hold device global xmit lock during tx disable
Prevent netif_tx_disable() running concurrently with dev_watchdog() by
taking the device global xmit lock. Otherwise, the recommended:
netif_carrier_off(dev);
netif_tx_disable(dev);
driver shutdown sequence can happen after the watchdog has already
checked carrier, resulting in possible false alarms. This is because
netif_tx_lock() only sets the frozen bit without maintaining the locks
on the individual queues.
Fixes:
c3f26a269c24 ("netdev: Fix lockdep warnings in multiqueue configurations.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Mon, 8 Feb 2021 12:20:47 +0000 (13:20 +0100)]
netfilter: nftables: relax check for stateful expressions in set definition
Restore the original behaviour where users are allowed to add an element
with any stateful expression if the set definition specifies no stateful
expressions. Make sure upper maximum number of stateful expressions of
NFT_SET_EXPR_MAX is not reached.
Fixes:
8cfd9b0f8515 ("netfilter: nftables: generalize set expressions support")
Fixes:
48b0ae046ee9 ("netfilter: nftables: netlink support for several set element expressions")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Fri, 5 Feb 2021 11:56:43 +0000 (12:56 +0100)]
netfilter: conntrack: skip identical origin tuple in same zone only
The origin skip check needs to re-test the zone. Else, we might skip
a colliding tuple in the reply direction.
This only occurs when using 'directional zones' where origin tuples
reside in different zones but the reply tuples share the same zone.
This causes the new conntrack entry to be dropped at confirmation time
because NAT clash resolution was elided.
Fixes:
4e35c1cb9460240 ("netfilter: nf_nat: skip nat clash resolution for same-origin entries")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Stefano Garzarella [Mon, 8 Feb 2021 14:44:54 +0000 (15:44 +0100)]
vsock/virtio: update credit only if socket is not closed
If the socket is closed or is being released, some resources used by
virtio_transport_space_update() such as 'vsk->trans' may be released.
To avoid a use after free bug we should only update the available credit
when we are sure the socket is still open and we have the lock held.
Fixes:
06a8fc78367d ("VSOCK: Introduce virtio_vsock_common.ko")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20210208144454.84438-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Mon, 8 Feb 2021 19:32:39 +0000 (11:32 -0800)]
Merge tag 'trace-v5.11-rc7' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Fix output of top level event tracing 'enable' file.
When writing a tool for enabling events in the tracing system, an
anomaly was discovered. The top level event 'enable' file would never
show '1' when all events were enabled.
The system and event 'enable' files worked as expected.
The reason was because the top level event 'enable' file included the
'ftrace' tracer events, which are not controlled by the 'enable' file
and would cause the output to be wrong. This appears to have been a
bug since it was created"
* tag 'trace-v5.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Do not count ftrace events in top level enable output
NeilBrown [Fri, 5 Feb 2021 00:36:30 +0000 (11:36 +1100)]
net: fix iteration for sctp transport seq_files
The sctp transport seq_file iterators take a reference to the transport
in the ->start and ->next functions and releases the reference in the
->show function. The preferred handling for such resources is to
release them in the subsequent ->next or ->stop function call.
Since Commit
1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration
code and interface") there is no guarantee that ->show will be called
after ->next, so this function can now leak references.
So move the sctp_transport_put() call to ->next and ->stop.
Fixes:
1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code and interface")
Reported-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ard Biesheuvel [Sat, 6 Feb 2021 08:49:37 +0000 (09:49 +0100)]
Revert "ACPICA: Interpreter: fix memory leak by using existing buffer"
This reverts commit
32cf1a12cad43358e47dac8014379c2f33dfbed4.
The 'exisitng buffer' in this case is the firmware provided table, and
we should not modify that in place. This fixes a crash on arm64 with
initrd table overrides, in which case the DSDT is not mapped with
read/write permissions.
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki [Thu, 4 Feb 2021 17:34:32 +0000 (18:34 +0100)]
cpufreq: ACPI: Update arch scale-invariance max perf ratio if CPPC is not there
If the maximum performance level taken for computing the
arch_max_freq_ratio value used in the x86 scale-invariance code is
higher than the one corresponding to the cpuinfo.max_freq value
coming from the acpi_cpufreq driver, the scale-invariant utilization
falls below 100% even if the CPU runs at cpuinfo.max_freq or slightly
faster, which causes the schedutil governor to select a frequency
below cpuinfo.max_freq. That frequency corresponds to a frequency
table entry below the maximum performance level necessary to get to
the "boost" range of CPU frequencies which prevents "boost"
frequencies from being used in some workloads.
While this issue is related to scale-invariance, it may be amplified
by commit
db865272d9c4 ("cpufreq: Avoid configuring old governors as
default with intel_pstate") from the 5.10 development cycle which
made it extremely easy to default to schedutil even if the preferred
driver is acpi_cpufreq as long as intel_pstate is built too, because
the mere presence of the latter effectively removes the ondemand
governor from the defaults. Distro kernels are likely to include
both intel_pstate and acpi_cpufreq on x86, so their users who cannot
use intel_pstate or choose to use acpi_cpufreq may easily be
affectecd by this issue.
If CPPC is available, it can be used to address this issue by
extending the frequency tables created by acpi_cpufreq to cover the
entire available frequency range (including "boost" frequencies) for
each CPU, but if CPPC is not there, acpi_cpufreq has no idea what
the maximum "boost" frequency is and the frequency tables created by
it cannot be extended in a meaningful way, so in that case make it
ask the arch scale-invariance code to to use the "nominal" performance
level for CPU utilization scaling in order to avoid the issue at hand.
Fixes:
db865272d9c4 ("cpufreq: Avoid configuring old governors as default with intel_pstate")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Rafael J. Wysocki [Thu, 4 Feb 2021 17:25:37 +0000 (18:25 +0100)]
cpufreq: ACPI: Extend frequency tables to cover boost frequencies
A severe performance regression on AMD EPYC processors when using
the schedutil scaling governor was discovered by Phoronix.com and
attributed to the following commits:
41ea667227ba ("x86, sched: Calculate frequency invariance for AMD
systems")
976df7e5730e ("x86, sched: Use midpoint of max_boost and max_P for
frequency invariance on AMD EPYC")
The source of the problem is that the maximum performance level taken
for computing the arch_max_freq_ratio value used in the x86 scale-
invariance code is higher than the one corresponding to the
cpuinfo.max_freq value coming from the acpi_cpufreq driver.
This effectively causes the scale-invariant utilization to fall below
100% even if the CPU runs at cpuinfo.max_freq or slightly faster, so
the schedutil governor selects a frequency below cpuinfo.max_freq
then. That frequency corresponds to a frequency table entry below
the maximum performance level necessary to get to the "boost" range
of CPU frequencies.
However, if the cpuinfo.max_freq value coming from acpi_cpufreq was
higher, the schedutil governor would select higher frequencies which
in turn would allow acpi_cpufreq to set more adequate performance
levels and to get to the "boost" range of CPU frequencies more often.
This issue affects any systems where acpi_cpufreq is used and the
"boost" (or "turbo") frequencies are enabled, not just AMD EPYC.
Moreover, commit
db865272d9c4 ("cpufreq: Avoid configuring old
governors as default with intel_pstate") from the 5.10 development
cycle made it extremely easy to default to schedutil even if the
preferred driver is acpi_cpufreq as long as intel_pstate is built
too, because the mere presence of the latter effectively removes the
ondemand governor from the defaults. Distro kernels are likely to
include both intel_pstate and acpi_cpufreq on x86, so their users
who cannot use intel_pstate or choose to use acpi_cpufreq may
easily be affectecd by this issue.
To address this issue, extend the frequency table constructed by
acpi_cpufreq for each CPU to cover the entire range of available
frequencies (including the "boost" ones) if CPPC is available and
indicates that "boost" (or "turbo") frequencies are enabled. That
causes cpuinfo.max_freq to become the maximum "boost" frequency of
the given CPU (instead of the maximum frequency returned by the ACPI
_PSS object that corresponds to the "nominal" performance level).
Fixes:
41ea667227ba ("x86, sched: Calculate frequency invariance for AMD systems")
Fixes:
976df7e5730e ("x86, sched: Use midpoint of max_boost and max_P for frequency invariance on AMD EPYC")
Fixes:
db865272d9c4 ("cpufreq: Avoid configuring old governors as default with intel_pstate")
Link: https://www.phoronix.com/scan.php?page=article&item=linux511-amd-schedutil&num=1
Link: https://lore.kernel.org/linux-pm/20210203135321.12253-2-ggherdovich@suse.cz/
Reported-by: Michael Larabel <Michael@phoronix.com>
Diagnosed-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Reviewed-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Tested-by: Michael Larabel <Michael@phoronix.com>
Cezary Rojewski [Wed, 3 Feb 2021 19:19:24 +0000 (20:19 +0100)]
dmaengine dw: Revert "dmaengine: dw: Enable runtime PM"
This reverts commit
842067940a3e3fc008a60fee388e000219b32632.
For some solutions e.g. sound/soc/intel/catpt, DW DMA is part of a
compound device (in that very example, domains: ADSP, SSP0, SSP1, DMA0
and DMA1 are part of a single entity) rather than being a standalone
one. Driver for said device may enlist DMA to transfer data during
suspend or resume sequences.
Manipulating RPM explicitly in dw's DMA request and release channel
functions causes suspend() to also invoke resume() for the exact same
device. Similar situation occurs for resume() sequence. Effectively
renders device dysfunctional after first suspend() attempt. Revert the
change to address the problem.
Fixes:
842067940a3e ("dmaengine: dw: Enable runtime PM")
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210203191924.15706-1-cezary.rojewski@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Linus Torvalds [Sun, 7 Feb 2021 21:57:38 +0000 (13:57 -0800)]
Linux 5.11-rc7
Linus Torvalds [Sun, 7 Feb 2021 18:45:26 +0000 (10:45 -0800)]
Merge tag 'libnvdimm-fixes-5.11-rc7' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A fix for a crash scenario that has been present since the initial
merge, a minor regression in sysfs attribute visibility, and a fix for
some flexible array warnings.
The bulk of this pull is an update to the libnvdimm unit test
infrastructure to test non-ACPI platforms. Given there is zero
regression risk for test updates, and the tests enable validation of
bits headed towards the next merge window, I saw no reason to hold the
new tests back. Santosh originally submitted this before the v5.11
window opened.
Summary:
- Fix a crash when sysfs accesses race 'dimm' driver probe/remove.
- Fix a regression in 'resource' attribute visibility necessary for
mapping badblocks and other physical address interrogations.
- Fix some flexible array warnings
- Expand the unit test infrastructure for non-ACPI platforms"
* tag 'libnvdimm-fixes-5.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm/dimm: Avoid race between probe and available_slots_show()
ndtest: Add papr health related flags
ndtest: Add nvdimm control functions
ndtest: Add regions and mappings to the test buses
ndtest: Add dimm attributes
ndtest: Add dimms to the two buses
ndtest: Add compatability string to treat it as PAPR family
testing/nvdimm: Add test module for non-nfit platforms
libnvdimm/namespace: Fix visibility of namespace resource attribute
libnvdimm/pmem: Remove unused header
ACPI: NFIT: Fix flexible_array.cocci warnings
Linus Torvalds [Sun, 7 Feb 2021 18:40:48 +0000 (10:40 -0800)]
Merge tag 'dma-mapping-5.11-2' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fix from Christoph Hellwig:
"Fix a 32 vs 64-bit padding issue in the new benchmark code (Barry
Song)"
* tag 'dma-mapping-5.11-2' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: benchmark: use u8 for reserved field in uAPI structure