OSDN Git Service
Nishanth Menon [Fri, 22 Aug 2014 14:01:01 +0000 (09:01 -0500)]
pinctrl: single: Add DRA7 pinctrl compatibility
DRA7 pinctrl definitions now differ from traditional 16 bit OMAP pin
ctrl definitions, in that all 32 bits are used to describe a single pin
Also the location of wakeupenable and event bits have changed.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Nishanth Menon [Fri, 23 May 2014 04:32:09 +0000 (23:32 -0500)]
pinctrl: bindings: Add OMAP pinctrl binding
Add basic skeleton of OMAP pinctrl bindings. This is compatible with
pinctrl,single bindings and is meant purely as a reference point.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rongjun Ying [Mon, 18 Aug 2014 08:49:24 +0000 (16:49 +0800)]
pinctrl: atlas6: Add I2S external clock input pingroup
The I2S controller can use the external clock as reference clock with
master mode. But based on different hardware or software design, this
external clock might be needed or not needed.
So the external input pin can be an independent pinctrl group, and the
card driver can decice to get it or not.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rongjun Ying [Mon, 18 Aug 2014 08:49:22 +0000 (16:49 +0800)]
pinctrl: atlas6: take mclk pin out of i2s pingroup
The I2S controller can output mclk to external audio codec. But by
hardware design, some codecs need mclk and some codecs do not need
mclk. So the mclk pin can be an independent pinctrl group, and the
card driver can get it or not based on boards.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Bin Shi [Mon, 18 Aug 2014 08:49:21 +0000 (16:49 +0800)]
pinctrl: sirf: fix lots of "line over 80 characters"
According to key customer's requirement, fix "line over 80
characters".
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Bin Shi [Mon, 18 Aug 2014 08:49:20 +0000 (16:49 +0800)]
pinctrl: sirf: fix "quoted string split across lines"
this patch fixes:
WARNING: quoted string split across lines
902: FILE: drivers/pinctrl/sirf/pinctrl-sirf.c:902:
+MODULE_AUTHOR("Rongjun Ying <rongjun.ying@csr.com>, "
+ "Yuping Luo <yuping.luo@csr.com>, "
WARNING: quoted string split across lines
903: FILE: drivers/pinctrl/sirf/pinctrl-sirf.c:903:
+ "Yuping Luo <yuping.luo@csr.com>, "
+ "Barry Song <baohua.song@csr.com>");
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kiran Padwal [Mon, 11 Aug 2014 14:54:57 +0000 (20:24 +0530)]
pinctrl: imx6sl: introduce MODULE_DEVICE_TABLE for module autoloading
Enable autoloading of pinctrl-imx6sl module when a corresponing DT entry is present.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kiran Padwal [Mon, 11 Aug 2014 11:17:50 +0000 (16:47 +0530)]
pinctrl: Make of_device_id array const
Make of_device_id array const, because all OF functions handle it as
const.
Signed-off-by: Kiran Padwal <kiran.padwal21@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Doug Anderson [Fri, 8 Aug 2014 22:29:09 +0000 (15:29 -0700)]
pinctrl: Add mux options 3 and 4 for rockchip pinctrl
Newer Rockchip SoCs have more muxing slots. Add slots 3 and 4 since
the rk3288 table goes all the way up to 4.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Alexander Shiyan [Sun, 27 Jul 2014 05:52:51 +0000 (09:52 +0400)]
pinctrl: Add i.MX21 pincontrol driver
This patch adds pincontrol driver for Freescale i.MX21 SOCs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds [Mon, 25 Aug 2014 22:36:20 +0000 (15:36 -0700)]
Linux 3.17-rc2
Linus Torvalds [Mon, 25 Aug 2014 22:34:28 +0000 (15:34 -0700)]
Merge tag 'nfs-for-3.17-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client fixes from Trond Myklebust:
"Highlights:
- more fixes for read/write codepath regressions
* sleeping while holding the inode lock
* stricter enforcement of page contiguity when coalescing requests
* fix up error handling in the page coalescing code
- don't busy wait on SIGKILL in the file locking code"
* tag 'nfs-for-3.17-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: Don't busy-wait on SIGKILL in __nfs_iocounter_wait
nfs: can_coalesce_requests must enforce contiguity
nfs: disallow duplicate pages in pgio page vectors
nfs: don't sleep with inode lock in lock_and_join_requests
nfs: fix error handling in lock_and_join_requests
nfs: use blocking page_group_lock in add_request
nfs: fix nonblocking calls to nfs_page_group_lock
nfs: change nfs_page_group_lock argument
Linus Torvalds [Mon, 25 Aug 2014 22:29:33 +0000 (15:29 -0700)]
Merge tag 'renesas-sh-drivers-for-v3.17' of git://git./linux/kernel/git/horms/renesas
Pull SH driver fix from Simon Horman:
"Confine SH_INTC to platforms that need it"
* tag 'renesas-sh-drivers-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
sh: intc: Confine SH_INTC to platforms that need it
Linus Torvalds [Mon, 25 Aug 2014 22:28:57 +0000 (15:28 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"Pretty much all across the field so with this we should be in
reasonable shape for the upcoming -rc2"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: OCTEON: make get_system_type() thread-safe
MIPS: CPS: Initialize EVA before bringing up VPEs from secondary cores
MIPS: Malta: EVA: Rename 'eva_entry' to 'platform_eva_init'
MIPS: EVA: Add new EVA header
MIPS: scall64-o32: Fix indirect syscall detection
MIPS: syscall: Fix AUDIT value for O32 processes on MIPS64
MIPS: Loongson: Fix COP2 usage for preemptible kernel
MIPS: NL: Fix nlm_xlp_defconfig build error
MIPS: Remove race window in page fault handling
MIPS: Malta: Improve system memory detection for '{e, }memsize' >= 2G
MIPS: Alchemy: Fix db1200 PSC clock enablement
MIPS: BCM47XX: Fix reboot problem on BCM4705/BCM4785
MIPS: Remove duplicated include from numa.c
MIPS: Add common plat_irq_dispatch declaration
MIPS: MSP71xx: remove unused plat_irq_dispatch() argument
MIPS: GIC: Remove useless parens from GICBIS().
MIPS: perf: Mark pmu interupt IRQF_NO_THREAD
Linus Torvalds [Mon, 25 Aug 2014 22:11:53 +0000 (15:11 -0700)]
Merge tag 'trace-fixes-v3.17-rc1' of git://git./linux/kernel/git/rostedt/linux-trace
Pull fix for ftrace function tracer/profiler conflict from Steven Rostedt:
"The rewrite of the ftrace code that makes it possible to allow for
separate trampolines had a design flaw with the interaction between
the function and function_graph tracers.
The main flaw was the simplification of the use of multiple tracers
having the same filter (like function and function_graph, that use the
set_ftrace_filter file to filter their code). The design assumed that
the two tracers could never run simultaneously as only one tracer can
be used at a time. The problem with this assumption was that the
function profiler could be implemented on top of the function graph
tracer, and the function profiler could run at the same time as the
function tracer. This caused the assumption to be broken and when
ftrace detected this failed assumpiton it would spit out a nasty
warning and shut itself down.
Instead of using a single ftrace_ops that switches between the
function and function_graph callbacks, the two tracers can again use
their own ftrace_ops. But instead of having a complex hierarchy of
ftrace_ops, the filter fields are placed in its own structure and the
ftrace_ops can carefully use the same filter. This change took a bit
to be able to allow for this and currently only the global_ops can
share the same filter, but this new design can easily be modified to
allow for any ftrace_ops to share its filter with another ftrace_ops.
The first four patches deal with the change of allowing the ftrace_ops
to share the filter (and this needs to go to 3.16 as well).
The fifth patch fixes a bug that was also caused by the new changes
but only for archs other than x86, and only if those archs implement a
direct call to the function_graph tracer which they do not do yet but
will in the future. It does not need to go to stable, but needs to be
fixed before the other archs update their code to allow direct calls
to the function_graph trampoline"
* tag 'trace-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Use current addr when converting to nop in __ftrace_replace_code()
ftrace: Fix function_profiler and function tracer together
ftrace: Fix up trampoline accounting with looping on hash ops
ftrace: Update all ftrace_ops for a ftrace_hash_ops update
ftrace: Allow ftrace_ops to use the hashes from other ops
Linus Torvalds [Sun, 24 Aug 2014 23:17:41 +0000 (16:17 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A couple of EFI fixes, plus misc fixes all around the map"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/arm64: Store Runtime Services revision
firmware: Do not use WARN_ON(!spin_is_locked())
x86_32, entry: Clean up sysenter_badsys declaration
x86/doc: Fix the 'tlb_single_page_flush_ceiling' sysconfig path
x86/mm: Fix sparse 'tlb_single_page_flush_ceiling' warning and make the variable read-mostly
x86/mm: Fix RCU splat from new TLB tracepoints
Linus Torvalds [Sun, 24 Aug 2014 23:16:55 +0000 (16:16 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"A kprobes and a perf compat ioctl fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Handle compat ioctl
kprobes: Skip kretprobe hit in NMI context to avoid deadlock
Linus Torvalds [Sun, 24 Aug 2014 22:57:00 +0000 (15:57 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes from this week, it's been pretty quiet and
nothing really stands out as particularly noteworthy here -- mostly
minor fixes across the field:
- ODROID booting was fixed due to PMIC interrupts missing in DT
- a collection of i.MX fixes
- minor Tegra fix for regulators
- Rockchip fix and addition of SoC-specific mailing list to make it
easier to find posted patches"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
bus: arm-ccn: Fix warning message
ARM: shmobile: koelsch: Remove non-existent i2c6 pinmux
ARM: tegra: apalis/colibri t30: fix on-module 5v0 supplies
MAINTAINERS: add new Rockchip SoC list
ARM: dts: rockchip: readd missing mmc0 pinctrl settings
ARM: dts: ODROID i2c improvements
ARM: dts: Enable PMIC interrupts on ODROID
ARM: dts: imx6sx: fix the pad setting for uart CTS_B
ARM: dts: i.MX53: fix apparent bug in VPU clks
ARM: imx: correct gpu2d_axi and gpu3d_axi clock setting
ARM: dts: imx6: edmqmx6: change enet reset pin
ARM: dts: vf610-twr: Fix pinctrl_esdhc1 pin definitions.
ARM: imx: remove unnecessary ARCH_HAS_OPP select
ARM: imx: fix TLB missing of IOMUXC base address during suspend
ARM: imx6: fix SMP compilation again
ARM: dt: sun6i: Add #address-cells and #size-cells to i2c controller nodes
Linus Torvalds [Sun, 24 Aug 2014 22:54:23 +0000 (15:54 -0700)]
Merge tag 'gpio-v3.17-2' of git://git./linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
- a largeish fix for the IRQ handling in the new Zynq driver. The
quite verbose commit message gives the exact details.
- move some defines for gpiod flags outside an ifdef to make stub
functions work again.
- various minor fixes that we can accept for -rc1.
* tag 'gpio-v3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio-lynxpoint: enable input sensing in resume
gpio: move GPIOD flags outside #ifdef
gpio: delete unneeded test before of_node_put
gpio: zynq: Fix IRQ handlers
gpiolib: devres: use correct structure type name in sizeof
MAINTAINERS: Change maintainer for gpio-bcm-kona.c
Linus Torvalds [Sun, 24 Aug 2014 22:48:12 +0000 (15:48 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Intel and radeon fixes.
Post KS/LC git requests from i915 and radeon stacked up. They are all
fixes along with some new pci ids for radeon, and one maintainers file
entry.
- i915: display fixes and irq fixes
- radeon: pci ids, and misc gpuvm, dpm and hdp cache"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (29 commits)
MAINTAINERS: Add entry for Renesas DRM drivers
drm/radeon: add additional SI pci ids
drm/radeon: add new bonaire pci ids
drm/radeon: add new KV pci id
Revert "drm/radeon: Use write-combined CPU mappings of ring buffers with PCIe"
drm/radeon: fix active_cu mask on SI and CIK after re-init (v3)
drm/radeon: fix active cu count for SI and CIK
drm/radeon: re-enable selective GPUVM flushing
drm/radeon: Sync ME and PFP after CP semaphore waits v4
drm/radeon: fix display handling in radeon_gpu_reset
drm/radeon: fix pm handling in radeon_gpu_reset
drm/radeon: Only flush HDP cache for indirect buffers from userspace
drm/radeon: properly document reloc priority mask
drm/i915: don't try to retrain a DP link on an inactive CRTC
drm/i915: make sure VDD is turned off during system suspend
drm/i915: cancel hotplug and dig_port work during suspend and unload
drm/i915: fix HPD IRQ reenable work cancelation
drm/i915: take display port power domain in DP HPD handler
drm/i915: Don't try to enable cursor from setplane when crtc is disabled
drm/i915: Skip load detect when intel_crtc->new_enable==true
...
Benjamin LaHaise [Sun, 24 Aug 2014 17:14:05 +0000 (13:14 -0400)]
aio: fix reqs_available handling
As reported by Dan Aloni, commit
f8567a3845ac ("aio: fix aio request
leak when events are reaped by userspace") introduces a regression when
user code attempts to perform io_submit() with more events than are
available in the ring buffer. Reverting that commit would reintroduce a
regression when user space event reaping is used.
Fixing this bug is a bit more involved than the previous attempts to fix
this regression. Since we do not have a single point at which we can
count events as being reaped by user space and io_getevents(), we have
to track event completion by looking at the number of events left in the
event ring. So long as there are as many events in the ring buffer as
there have been completion events generate, we cannot call
put_reqs_available(). The code to check for this is now placed in
refill_reqs_available().
A test program from Dan and modified by me for verifying this bug is available
at http://www.kvack.org/~bcrl/
20140824-aio_bug.c .
Reported-by: Dan Aloni <dan@kernelim.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Acked-by: Dan Aloni <dan@kernelim.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Mateusz Guzik <mguzik@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: stable@vger.kernel.org # v3.16 and anything that f8567a3845ac was backported to
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pawel Moll [Mon, 18 Aug 2014 17:20:49 +0000 (18:20 +0100)]
bus: arm-ccn: Fix warning message
A message warning a user about wrong vc value was printing
out port instead.
Reported-by: Drew Richardson <drew.richardson@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Geert Uytterhoeven [Thu, 14 Aug 2014 22:19:10 +0000 (07:19 +0900)]
ARM: shmobile: koelsch: Remove non-existent i2c6 pinmux
On r8a7791, i2c6 (aka iic3) doesn't need pinmux, but the koelsch dts
refers to non-existent pinmux configuration data:
pinmux core: sh-pfc does not support function i2c6
sh-pfc
e6060000.pfc: invalid function i2c6 in map table
Remove it to fix this.
Fixes: commit
1d41f36a68c0f4e9b01d563ce33bab5201858b54 ("ARM: shmobile:
koelsch dts: Add VDD MPU regulator for DVFS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
Marcel Ziswiler [Fri, 22 Aug 2014 19:25:10 +0000 (13:25 -0600)]
ARM: tegra: apalis/colibri t30: fix on-module 5v0 supplies
Working on Gigabit/PCIe support in U-Boot for Apalis T30 I realised
that the current device tree source includes for our modules only
happen to work due to referencing the on-carrier 5v0 supply from USB
which is not at all available on-module. The modules actually contain
TPS60150 charge pumps to generate the PMIC required 5 volts from the
one and only 3.3 volt module supply. This patch fixes this.
(Note: When back-porting this to v3.16 stable releases, simply drop the
change to tegra30-apalis.dtsi; that file was added in v3.17)
Cc: <stable@vger.kernel.org> #v3.16+
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sun, 24 Aug 2014 18:19:37 +0000 (11:19 -0700)]
Merge tag 'v3.17-rockchip-fixes1' of git://git./linux/kernel/git/mmind/linux-rockchip into fixes
Merge "ARM: rockchip: fix for 3.17" from Heiko Stubner:
Pinctrl that got accidentially dropped when reorganizing the
dts files and addition of the new Rockchip list to MAINTAINERS.
* tag 'v3.17-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
MAINTAINERS: add new Rockchip SoC list
ARM: dts: rockchip: readd missing mmc0 pinctrl settings
Signed-off-by: Olof Johansson <olof@lixom.net>
Laurent Pinchart [Tue, 19 Aug 2014 21:04:31 +0000 (23:04 +0200)]
MAINTAINERS: Add entry for Renesas DRM drivers
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Dave Airlie [Sun, 24 Aug 2014 05:47:46 +0000 (15:47 +1000)]
Merge branch 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux into drm-next
This pull just contains some new pci ids.
* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add additional SI pci ids
drm/radeon: add new bonaire pci ids
drm/radeon: add new KV pci id
Heiko Stuebner [Wed, 20 Aug 2014 10:31:03 +0000 (12:31 +0200)]
MAINTAINERS: add new Rockchip SoC list
Add the new list that Rockchip-specific patches should also be directed to.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Heiko Stuebner [Mon, 11 Aug 2014 17:51:44 +0000 (19:51 +0200)]
ARM: dts: rockchip: readd missing mmc0 pinctrl settings
During the restructuring of the Rockchip Cortex-A9 dtsi files it seems
like the pinctrl settings vanished at some point from the mmc0 support.
This of course renders them unusable, so readd the necessary pinctrl
properties.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Olof Johansson [Sat, 23 Aug 2014 05:57:22 +0000 (22:57 -0700)]
Merge tag 'sunxi-dt-for-3.17-2' of git://git./linux/kernel/git/mripard/linux into fixes
Merge "Allwinner DT changes, take 2" from Maxime Ripard:
Only a single patch in here that fixes a DTC warning.
* tag 'sunxi-dt-for-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dt: sun6i: Add #address-cells and #size-cells to i2c controller nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Steven Rostedt (Red Hat) [Mon, 18 Aug 2014 00:59:10 +0000 (20:59 -0400)]
ftrace: Use current addr when converting to nop in __ftrace_replace_code()
In __ftrace_replace_code(), when converting the call to a nop in a function
it needs to compare against the "curr" (current) value of the ftrace ops, and
not the "new" one. It currently does not affect x86 which is the only arch
to do the trampolines with function graph tracer, but when other archs that do
depend on this code implement the function graph trampoline, it can crash.
Here's an example when ARM uses the trampolines (in the future):
------------[ cut here ]------------
WARNING: CPU: 0 PID: 9 at kernel/trace/ftrace.c:1716 ftrace_bug+0x17c/0x1f4()
Modules linked in: omap_rng rng_core ipv6
CPU: 0 PID: 9 Comm: migration/0 Not tainted
3.16.0-test-10959-gf0094b28f303-dirty #52
[<
c02188f4>] (unwind_backtrace) from [<
c021343c>] (show_stack+0x20/0x24)
[<
c021343c>] (show_stack) from [<
c095a674>] (dump_stack+0x78/0x94)
[<
c095a674>] (dump_stack) from [<
c02532a0>] (warn_slowpath_common+0x7c/0x9c)
[<
c02532a0>] (warn_slowpath_common) from [<
c02532ec>] (warn_slowpath_null+0x2c/0x34)
[<
c02532ec>] (warn_slowpath_null) from [<
c02cbac4>] (ftrace_bug+0x17c/0x1f4)
[<
c02cbac4>] (ftrace_bug) from [<
c02cc44c>] (ftrace_replace_code+0x80/0x9c)
[<
c02cc44c>] (ftrace_replace_code) from [<
c02cc658>] (ftrace_modify_all_code+0xb8/0x164)
[<
c02cc658>] (ftrace_modify_all_code) from [<
c02cc718>] (__ftrace_modify_code+0x14/0x1c)
[<
c02cc718>] (__ftrace_modify_code) from [<
c02c7244>] (multi_cpu_stop+0xf4/0x134)
[<
c02c7244>] (multi_cpu_stop) from [<
c02c6e90>] (cpu_stopper_thread+0x54/0x130)
[<
c02c6e90>] (cpu_stopper_thread) from [<
c0271cd4>] (smpboot_thread_fn+0x1ac/0x1bc)
[<
c0271cd4>] (smpboot_thread_fn) from [<
c026ddf0>] (kthread+0xe0/0xfc)
[<
c026ddf0>] (kthread) from [<
c020f318>] (ret_from_fork+0x14/0x20)
---[ end trace
dc9ce72c5b617d8f ]---
[ 65.047264] ftrace failed to modify [<
c0208580>] asm_do_IRQ+0x10/0x1c
[ 65.054070] actual: 85:1b:00:eb
Fixes:
7413af1fb70e7 "ftrace: Make get_ftrace_addr() and get_ftrace_addr_old() global"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Steven Rostedt (Red Hat) [Fri, 15 Aug 2014 21:18:46 +0000 (17:18 -0400)]
ftrace: Fix function_profiler and function tracer together
The latest rewrite of ftrace removed the separate ftrace_ops of
the function tracer and the function graph tracer and had them
share the same ftrace_ops. This simplified the accounting by removing
the multiple layers of functions called, where the global_ops func
would call a special list that would iterate over the other ops that
were registered within it (like function and function graph), which
itself was registered to the ftrace ops list of all functions
currently active. If that sounds confusing, the code that implemented
it was also confusing and its removal is a good thing.
The problem with this change was that it assumed that the function
and function graph tracer can never be used at the same time.
This is mostly true, but there is an exception. That is when the
function profiler uses the function graph tracer to profile.
The function profiler can be activated the same time as the function
tracer, and this breaks the assumption and the result is that ftrace
will crash (it detects the error and shuts itself down, it does not
cause a kernel oops).
To solve this issue, a previous change allowed the hash tables
for the functions traced by a ftrace_ops to be a pointer and let
multiple ftrace_ops share the same hash. This allows the function
and function_graph tracer to have separate ftrace_ops, but still
share the hash, which is what is done.
Now the function and function graph tracers have separate ftrace_ops
again, and the function tracer can be run while the function_profile
is active.
Cc: stable@vger.kernel.org # 3.16 (apply after 3.17-rc4 is out)
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
David Jeffery [Tue, 5 Aug 2014 15:19:42 +0000 (11:19 -0400)]
nfs: Don't busy-wait on SIGKILL in __nfs_iocounter_wait
If a SIGKILL is sent to a task waiting in __nfs_iocounter_wait,
it will busy-wait or soft lockup in its while loop.
nfs_wait_bit_killable won't sleep, and the loop won't exit on
the error return.
Stop the busy-wait by breaking out of the loop when
nfs_wait_bit_killable returns an error.
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Weston Andros Adamson [Thu, 14 Aug 2014 21:39:33 +0000 (17:39 -0400)]
nfs: can_coalesce_requests must enforce contiguity
Commit
6094f83864c1d1296566a282cba05ba613f151ee
"nfs: allow coalescing of subpage requests" got rid of the requirement
that requests cover whole pages, but it made some incorrect assumptions.
It turns out that callers of this interface can map adjacent requests
(by file position as seen by req_offset + req->wb_bytes) to different pages,
even when they could share a page. An example is the direct I/O interface -
iov_iter_get_pages_alloc may return one segment with a partial page filled
and the next segment (which is adjacent in the file position) starts with a
new page.
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Weston Andros Adamson [Thu, 14 Aug 2014 21:39:32 +0000 (17:39 -0400)]
nfs: disallow duplicate pages in pgio page vectors
Adjacent requests that share the same page are allowed, but should only
use one entry in the page vector. This avoids overruning the page
vector - it is sized based on how many bytes there are, not by
request count.
This fixes issues that manifest as "Redzone overwritten" bugs (the
vector overrun) and hangs waiting on page read / write, as it waits on
the same page more than once.
This also adds bounds checking to the page vector with a graceful failure
(WARN_ON_ONCE and pgio error returned to application).
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Weston Andros Adamson [Fri, 8 Aug 2014 15:00:57 +0000 (11:00 -0400)]
nfs: don't sleep with inode lock in lock_and_join_requests
This handles the 'nonblock=false' case in nfs_lock_and_join_requests.
If the group is already locked and blocking is allowed, drop the inode lock
and wait for the group lock to be cleared before trying it all again.
This should fix warnings found in peterz's tree (sched/wait branch), where
might_sleep() checks are added to wait.[ch].
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Weston Andros Adamson [Fri, 8 Aug 2014 15:00:56 +0000 (11:00 -0400)]
nfs: fix error handling in lock_and_join_requests
This fixes handling of errors from nfs_page_group_lock in
nfs_lock_and_join_requests. It now releases the inode lock and the
reference to the head request.
Reported-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Weston Andros Adamson [Fri, 8 Aug 2014 15:00:55 +0000 (11:00 -0400)]
nfs: use blocking page_group_lock in add_request
__nfs_pageio_add_request was calling nfs_page_group_lock nonblocking, but
this can return -EAGAIN which would end up passing -EIO to the application.
There is no reason not to block in this path, so change the two calls to
do so. Also, there is no need to check the return value of
nfs_page_group_lock when nonblock=false, so remove the error handling code.
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Weston Andros Adamson [Fri, 8 Aug 2014 15:00:54 +0000 (11:00 -0400)]
nfs: fix nonblocking calls to nfs_page_group_lock
nfs_page_group_lock was calling wait_on_bit_lock even when told not to
block. Fix by first trying test_and_set_bit, followed by wait_on_bit_lock
if and only if blocking is allowed. Return -EAGAIN if nonblocking and the
test_and_set of the bit was already locked.
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Weston Andros Adamson [Fri, 8 Aug 2014 15:00:53 +0000 (11:00 -0400)]
nfs: change nfs_page_group_lock argument
Flip the meaning of the second argument from 'wait' to 'nonblock' to
match related functions. Update all five calls to reflect this change.
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Linus Torvalds [Fri, 22 Aug 2014 21:50:21 +0000 (14:50 -0700)]
Merge tag 'pwm/for-3.17-rc2' of git://git./linux/kernel/git/thierry.reding/linux-pwm
Pull pwm fix from Thierry Reding:
"Just one bugfix for the PWM lookup table code that would cause a PWM
channel to be set to the wrong period and polarity for non-perfect
matches"
* tag 'pwm/for-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: Fix period and polarity in pwm_get() for non-perfect matches
Michal Kazior [Mon, 18 Aug 2014 11:19:09 +0000 (13:19 +0200)]
mac80211: fix channel switch for chanctx-based drivers
The new_ctx pointer is set only for non-chanctx drivers. This yielded a
crash for chanctx-based drivers during channel switch finalization:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000020
IP: ieee80211_vif_use_reserved_switch+0x71c/0xb00 [mac80211]
Use an adequate chanctx pointer to fix this.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 22 Aug 2014 21:33:18 +0000 (14:33 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"Here are some bug fixes that have piled up during ksummit/linuxcon.
1) Fix endian problems in ibmveth, from Anton Blanchard.
2) IPV6 routing code does GFP_KERNEL allocation in atomic, fix from
Benjamin Block.
3) SCTP association fixes from Daniel Borkmann.
4) When multiple VLAN headers are present we have to make sure the
second and subsequent ones are pullable in the SKB otherwise we
blindly dereference garbage. From Jiri Benc.
5) The argument adjustment of the signature of hlist_add_after*()
introduced a regression in the batman-adv code, fix from Sven
Eckelmann.
6) Fix TX hang handling to avoid a panic in i40e, from Anjali Singhai
Jain.
7) PTP flag test is inverted in i40e driver, from Jesse Brandeburg.
8) ATM LEC driver needs to hold RTNL mutex over MTU changes, from
Chas Williams.
9) Truncate packets larger then the TPACKET_V3 format configured
buffers, otherwise we overwrite past the end of said buffers.
From Eric Dumazet.
10) Fix endianness bugs in qlcnic firmware handling, from Rajesh
Borundia and Shahed Shaikh.
11) CXGB4 sometimes doesn't get all of the TX completion events it
should resulting in SKBs getting stuck in the TX queue, from
Hariprasad Shenai.
12) When the FEC chip's PTP clock is disabled, you can't access the
register. Add necessary checks to avoid the resulting hang, from
Fugang Duan"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
drivers: isdn: eicon: xdi_msg.h: Fix typo in #ifndef
net: sctp: fix suboptimal edge-case on non-active active/retrans path selection
net: sctp: spare unnecessary comparison in sctp_trans_elect_best
net: ethernet: broadcom: bnx2x: Remove redundant #ifdef
ibmveth: Fix endian issues with rx_no_buffer statistic
net: xgene: fix possible NULL dereference in xgene_enet_free_desc_rings()
openvswitch: fix panic with multiple vlan headers
net: ipv6: fib: don't sleep inside atomic lock
net: fec: ptp: avoid register access when ipg clock is disabled
cxgb4: Free completed tx skbs promptly
cxgb4: Fix race condition in cleanup
sctp: not send SCTP_PEER_ADDR_CHANGE notifications with failed probe
bnx2x: Revert UNDI flushing mechanism
qlcnic: Fix endianess issue in firmware load from file operation
qlcnic: Fix endianess issue in FW dump template header
qlcnic: Fix flash access interface to application
MAINTAINERS: Add section for MRF24J40 IEEE 802.15.4 radio driver
macvlan: Allow setting multicast filter on all macvlan types
packet: handle too big packets for PACKET_V3
MAINTAINERS: add entry for ec_bhf driver
...
Steven Rostedt (Red Hat) [Thu, 21 Aug 2014 03:57:04 +0000 (23:57 -0400)]
ftrace: Fix up trampoline accounting with looping on hash ops
Now that a ftrace_hash can be shared by multiple ftrace_ops, they can dec
the rec->flags by more than once (one per those that share the ftrace_hash).
This means that the tramp_hash may not have a hash item when it was added.
For example, if two ftrace_ops share a hash for a ftrace record, and the
first ops has a trampoline, when it adds itself it will set the rec->flags
TRAMP flag and increments its nr_trampolines counter. When the second ops
is added, it must clear that tramp flag but also decrement the other ops
that shares its hash. As the update to the function callbacks has not yet
been performed, the other ops will not have the tramp hash set yet and it
can not be used to know to decrement its nr_trampolines.
Luckily, the tramp_hash does not need to be used. As the ftrace_mutex is
held, a ops with a trampoline to a record during an update of another ops
that shares the record will have its func_hash pointing to it. Since a
trampoline can only be set for a record if only one ops is attached to it,
we can just check if the record has a trampoline (the FTRACE_FL_TRAMP flag
is set) and then find the ops that has this record in its hashes.
Also added some output to help debug when things go wrong.
Cc: stable@vger.kernel.org # 3.16+ (apply after 3.17-rc4 is out)
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Rasmus Villemoes [Fri, 22 Aug 2014 16:39:14 +0000 (18:39 +0200)]
drivers: isdn: eicon: xdi_msg.h: Fix typo in #ifndef
Test for definedness of the macro which is actually defined (the
change is hard to see: it is s/SSS/SSA/).
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 22 Aug 2014 11:03:30 +0000 (13:03 +0200)]
net: sctp: fix suboptimal edge-case on non-active active/retrans path selection
In SCTP, selection of active (T.ACT) and retransmission (T.RET)
transports is being done whenever transport control operations
(UP, DOWN, PF, ...) are engaged through sctp_assoc_control_transport().
Commits
4c47af4d5eb2 ("net: sctp: rework multihoming retransmission
path selection to rfc4960") and
a7288c4dd509 ("net: sctp: improve
sctp_select_active_and_retran_path selection") have both improved
it towards a more fine-grained and optimal path selection.
Currently, the selection algorithm for T.ACT and T.RET is as follows:
1) Elect the two most recently used ACTIVE transports T1, T2 for
T.ACT, T.RET, where T.ACT<-T1 and T1 is most recently used
2) In case primary path T.PRI not in {T1, T2} but ACTIVE, set
T.ACT<-T.PRI and T.RET<-T1
3) If only T1 is ACTIVE from the set, set T.ACT<-T1 and T.RET<-T1
4) If none is ACTIVE, set T.ACT<-best(T.PRI, T.RET, T3) where
T3 is the most recently used (if avail) in PF, set T.RET<-T.PRI
Prior to above commits, 4) was simply a camp on T.ACT<-T.PRI and
T.RET<-T.PRI, ignoring possible paths in PF. Camping on T.PRI is
still slightly suboptimal as it can lead to the following scenario:
Setup:
<A> <B>
T1: p1p1 (10.0.10.10) <==> .'`) <==> p1p1 (10.0.10.12) <= T.PRI
T2: p1p2 (10.0.10.20) <==> (_ . ) <==> p1p2 (10.0.10.22)
net.sctp.rto_min = 1000
net.sctp.path_max_retrans = 2
net.sctp.pf_retrans = 0
net.sctp.hb_interval = 1000
T.PRI is permanently down, T2 is put briefly into PF state (e.g. due to
link flapping). Here, the first time transmission is sent over PF path
T2 as it's the only non-INACTIVE path, but the retransmitted data-chunks
are sent over the INACTIVE path T1 (T.PRI), which is not good.
After the patch, it's choosing better transports in both cases by
modifying step 4):
4) If none is ACTIVE, set T.ACT_new<-best(T.ACT_old, T3) where T3 is
the most recently used (if avail) in PF, set T.RET<-T.ACT_new
This will still select a best possible path in PF if available (which
can also include T.PRI/T.RET), and set both T.ACT/T.RET to it.
In case sctp_assoc_control_transport() *just* put T.ACT_old into INACTIVE
as it transitioned from ACTIVE->PF->INACTIVE and stays in INACTIVE just
for a very short while before going back ACTIVE, it will guarantee that
this path will be reselected for T.ACT/T.RET since T3 (PF) is not
available.
Previously, this was not possible, as we would only select between T.PRI
and T.RET, and a possible T3 would be NULL due to the fact that we have
just transitioned T3 in sctp_assoc_control_transport() from PF->INACTIVE
and would select a suboptimal path when T.PRI/T.RET have worse properties.
In the case that T.ACT_old permanently went to INACTIVE during this
transition and there's no PF path available, plus T.PRI and T.RET are
INACTIVE as well, we would now camp on T.ACT_old, but if everything is
being INACTIVE there's really not much we can do except hoping for a
successful HB to bring one of the transports back up again and, thus
cause a new selection through sctp_assoc_control_transport().
Now both tests work fine:
Case 1:
1. T1 S(ACTIVE) T.ACT
T2 S(ACTIVE) T.RET
2. T1 S(ACTIVE) T.ACT, T.RET
T2 S(PF)
3. T1 S(ACTIVE) T.ACT, T.RET
T2 S(INACTIVE)
5. T1 S(PF) T.ACT, T.RET
T2 S(INACTIVE)
[ 5.1 T1 S(INACTIVE) T.ACT, T.RET
T2 S(INACTIVE) ]
6. T1 S(ACTIVE) T.ACT, T.RET
T2 S(INACTIVE)
7. T1 S(ACTIVE) T.ACT
T2 S(ACTIVE) T.RET
Case 2:
1. T1 S(ACTIVE) T.ACT
T2 S(ACTIVE) T.RET
2. T1 S(PF)
T2 S(ACTIVE) T.ACT, T.RET
3. T1 S(INACTIVE)
T2 S(ACTIVE) T.ACT, T.RET
5. T1 S(INACTIVE)
T2 S(PF) T.ACT, T.RET
[ 5.1 T1 S(INACTIVE)
T2 S(INACTIVE) T.ACT, T.RET ]
6. T1 S(INACTIVE)
T2 S(ACTIVE) T.ACT, T.RET
7. T1 S(ACTIVE) T.ACT
T2 S(ACTIVE) T.RET
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 22 Aug 2014 11:03:29 +0000 (13:03 +0200)]
net: sctp: spare unnecessary comparison in sctp_trans_elect_best
When both transports are the same, we don't have to go down that
road only to realize that we will return the very same transport.
We are guaranteed that curr is always non-NULL. Therefore, just
short-circuit this special case.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rasmus Villemoes [Wed, 20 Aug 2014 13:14:49 +0000 (15:14 +0200)]
net: ethernet: broadcom: bnx2x: Remove redundant #ifdef
Nothing defines _ASM_GENERIC_INT_L64_H, it is a weird way to check for
64 bit longs, and u64 should be printed using %llx anyway.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Blanchard [Fri, 22 Aug 2014 01:36:52 +0000 (11:36 +1000)]
ibmveth: Fix endian issues with rx_no_buffer statistic
Hidden away in the last 8 bytes of the buffer_list page is a solitary
statistic. It needs to be byte swapped or else ethtool -S will
produce numbers that terrify the user.
Since we do this in multiple places, create a helper function with a
comment explaining what is going on.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Iyappan Subramanian [Thu, 21 Aug 2014 20:44:48 +0000 (13:44 -0700)]
net: xgene: fix possible NULL dereference in xgene_enet_free_desc_rings()
A NULL pointer dereference is possible for the argument ring->buf_pool
which is passed to xgene_enet_free_desc_ring(), as ring could be NULL.
And now since NULL pointers are being checked for before the calls to
xgene_enet_free_desc_ring(), might as well take advantage of them and
not call the function if the argument would be NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Thu, 21 Aug 2014 19:33:44 +0000 (21:33 +0200)]
openvswitch: fix panic with multiple vlan headers
When there are multiple vlan headers present in a received frame, the first
one is put into vlan_tci and protocol is set to ETH_P_8021Q. Anything in the
skb beyond the VLAN TPID may be still non-linear, including the inner TCI
and ethertype. While ovs_flow_extract takes care of IP and IPv6 headers, it
does nothing with ETH_P_8021Q. Later, if OVS_ACTION_ATTR_POP_VLAN is
executed, __pop_vlan_tci pulls the next vlan header into vlan_tci.
This leads to two things:
1. Part of the resulting ethernet header is in the non-linear part of the
skb. When eth_type_trans is called later as the result of
OVS_ACTION_ATTR_OUTPUT, kernel BUGs in __skb_pull. Also, __pop_vlan_tci
is in fact accessing random data when it reads past the TPID.
2. network_header points into the ethernet header instead of behind it.
mac_len is set to a wrong value (10), too.
Reported-by: Yulong Pei <ypei@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Block [Thu, 21 Aug 2014 17:37:48 +0000 (19:37 +0200)]
net: ipv6: fib: don't sleep inside atomic lock
The function fib6_commit_metrics() allocates a piece of memory in mode
GFP_KERNEL while holding an atomic lock from higher up in the stack, in
the function __ip6_ins_rt(). This produces the following BUG:
> BUG: sleeping function called from invalid context at mm/slub.c:1250
> in_atomic(): 1, irqs_disabled(): 0, pid: 2909, name: dhcpcd
> 2 locks held by dhcpcd/2909:
> #0: (rtnl_mutex){+.+.+.}, at: [<
ffffffff81978e67>] rtnl_lock+0x17/0x20
> #1: (&tb->tb6_lock){++--+.}, at: [<
ffffffff81a6951a>] ip6_route_add+0x65a/0x800
> CPU: 1 PID: 2909 Comm: dhcpcd Not tainted 3.17.0-rc1 #1
> Hardware name: ASUS All Series/Q87T, BIOS 0216 10/16/2013
>
0000000000000008 ffff8800c8f13858 ffffffff81af135a 0000000000000000
>
ffff880212202430 ffff8800c8f13878 ffffffff810f8d3a ffff880212202c98
>
0000000000000010 ffff8800c8f138c8 ffffffff8121ad0e 0000000000000001
> Call Trace:
> [<
ffffffff81af135a>] dump_stack+0x4e/0x68
> [<
ffffffff810f8d3a>] __might_sleep+0x10a/0x120
> [<
ffffffff8121ad0e>] kmem_cache_alloc_trace+0x4e/0x190
> [<
ffffffff81a6bcd6>] ? fib6_commit_metrics+0x66/0x110
> [<
ffffffff81a6bcd6>] fib6_commit_metrics+0x66/0x110
> [<
ffffffff81a6cbf3>] fib6_add+0x883/0xa80
> [<
ffffffff81a6951a>] ? ip6_route_add+0x65a/0x800
> [<
ffffffff81a69535>] ip6_route_add+0x675/0x800
> [<
ffffffff81a68f2a>] ? ip6_route_add+0x6a/0x800
> [<
ffffffff81a6990c>] inet6_rtm_newroute+0x5c/0x80
> [<
ffffffff8197cf01>] rtnetlink_rcv_msg+0x211/0x260
> [<
ffffffff81978e67>] ? rtnl_lock+0x17/0x20
> [<
ffffffff81119708>] ? lock_release_holdtime+0x28/0x180
> [<
ffffffff81978e67>] ? rtnl_lock+0x17/0x20
> [<
ffffffff8197ccf0>] ? __rtnl_unlock+0x20/0x20
> [<
ffffffff819a989e>] netlink_rcv_skb+0x6e/0xd0
> [<
ffffffff81978ee5>] rtnetlink_rcv+0x25/0x40
> [<
ffffffff819a8e59>] netlink_unicast+0xd9/0x180
> [<
ffffffff819a9600>] netlink_sendmsg+0x700/0x770
> [<
ffffffff81103735>] ? local_clock+0x25/0x30
> [<
ffffffff8194e83c>] sock_sendmsg+0x6c/0x90
> [<
ffffffff811f98e3>] ? might_fault+0xa3/0xb0
> [<
ffffffff8195ca6d>] ? verify_iovec+0x7d/0xf0
> [<
ffffffff8194ec3e>] ___sys_sendmsg+0x37e/0x3b0
> [<
ffffffff8111ef15>] ? trace_hardirqs_on_caller+0x185/0x220
> [<
ffffffff81af979e>] ? mutex_unlock+0xe/0x10
> [<
ffffffff819a55ec>] ? netlink_insert+0xbc/0xe0
> [<
ffffffff819a65e5>] ? netlink_autobind.isra.30+0x125/0x150
> [<
ffffffff819a6520>] ? netlink_autobind.isra.30+0x60/0x150
> [<
ffffffff819a84f9>] ? netlink_bind+0x159/0x230
> [<
ffffffff811f989a>] ? might_fault+0x5a/0xb0
> [<
ffffffff8194f25e>] ? SYSC_bind+0x7e/0xd0
> [<
ffffffff8194f8cd>] __sys_sendmsg+0x4d/0x80
> [<
ffffffff8194f912>] SyS_sendmsg+0x12/0x20
> [<
ffffffff81afc692>] system_call_fastpath+0x16/0x1b
Fixing this by replacing the mode GFP_KERNEL with GFP_ATOMIC.
Signed-off-by: Benjamin Block <bebl@mageta.org>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nimrod Andy [Thu, 21 Aug 2014 09:09:38 +0000 (17:09 +0800)]
net: fec: ptp: avoid register access when ipg clock is disabled
The current kernel hang on i.MX6SX with rootfs mount from MMC.
The root cause is that ptp uses a periodic timer to access enet register
even if ipg clock is disabled.
FEC ptp driver start one period timer to read 1588 counter register in the
ptp init function that is called after FEC driver is probed.
To save power, after FEC probe finish, FEC driver disable all clocks including
ipg clock that is needed for register access.
i.MX5x, i.MX6q/dl/sl FEC register access don't cause system hang when ipg clock
is disabled, just return zero value. But for i.MX6sx SOC, it cause system hang.
To avoid the issue, we need to check ptp clock status before ptp timer count access.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steven Rostedt (Red Hat) [Mon, 18 Aug 2014 17:21:08 +0000 (13:21 -0400)]
ftrace: Update all ftrace_ops for a ftrace_hash_ops update
When updating what an ftrace_ops traces, if it is registered (that is,
actively tracing), and that ftrace_ops uses the shared global_ops
local_hash, then we need to update all tracers that are active and
also share the global_ops' ftrace_hash_ops.
Cc: stable@vger.kernel.org # 3.16 (apply after 3.17-rc4 is out)
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Steven Rostedt (Red Hat) [Fri, 15 Aug 2014 21:23:02 +0000 (17:23 -0400)]
ftrace: Allow ftrace_ops to use the hashes from other ops
Currently the top level debug file system function tracer shares its
ftrace_ops with the function graph tracer. This was thought to be fine
because the tracers are not used together, as one can only enable
function or function_graph tracer in the current_tracer file.
But that assumption proved to be incorrect. The function profiler
can use the function graph tracer when function tracing is enabled.
Since all function graph users uses the function tracing ftrace_ops
this causes a conflict and when a user enables both function profiling
as well as the function tracer it will crash ftrace and disable it.
The quick solution so far is to move them as separate ftrace_ops like
it was earlier. The problem though is to synchronize the functions that
are traced because both function and function_graph tracer are limited
by the selections made in the set_ftrace_filter and set_ftrace_notrace
files.
To handle this, a new structure is made called ftrace_ops_hash. This
structure will now hold the filter_hash and notrace_hash, and the
ftrace_ops will point to this structure. That will allow two ftrace_ops
to share the same hashes.
Since most ftrace_ops do not share the hashes, and to keep allocation
simple, the ftrace_ops structure will include both a pointer to the
ftrace_ops_hash called func_hash, as well as the structure itself,
called local_hash. When the ops are registered, the func_hash pointer
will be initialized to point to the local_hash within the ftrace_ops
structure. Some of the ftrace internal ftrace_ops will be initialized
statically. This will allow for the function and function_graph tracer
to have separate ops but still share the same hash tables that determine
what functions they trace.
Cc: stable@vger.kernel.org # 3.16 (apply after 3.17-rc4 is out)
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Linus Torvalds [Fri, 22 Aug 2014 16:08:20 +0000 (09:08 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"This small set of fixes addresses a few issues introduced during the
merge window, including:
- fix typo in I-cache detection that was causing us to treat all
I-caches as aliasing
- hook up memfd_create and getrandom syscalls for native and compat
- revert a temporary hack for defconfig builds in -next (the audit
tree changes didn't make it in this merge window)
- a couple of UEFI fixes for TEXT_OFFSET fuzzing and /memreserve/
- a simple sparsemem fix for 48-bit physical addressing
- small defconfig updates to get autotesters working with X-gene"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
Revert "arm64: Do not invoke audit_syscall_* functions if !CONFIG_AUDIT_SYSCALL"
arm64: mm: update max pa bits to 48
arm64: ignore DT memreserve entries when booting in UEFI mode
arm64: configs: Enable X-Gene SATA and ethernet in defconfig
arm64: align randomized TEXT_OFFSET on 4 kB boundary
asm-generic: add memfd_create system call to unistd.h
arm64: compat: wire up memfd_create and getrandom syscalls for aarch32
arm64: fix typo in I-cache policy detection
Linus Torvalds [Fri, 22 Aug 2014 16:06:22 +0000 (09:06 -0700)]
Merge tag 'iommu-fixes-v3.17-rc1' of git://git./linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"The fixes include:
- fix a crash in the VT-d driver when devices with a driver attached
are hot-unplugged
- fix a AMD IOMMU driver crash with device assignment of 32 bit PCI
devices to KVM guests
- fix for a copy&paste error in generic IOMMU code. Now the right
function pointer is checked before calling"
* tag 'iommu-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/core: Check for the right function pointer in iommu_map()
iommu/amd: Fix cleanup_domain for mass device removal
iommu/vt-d: Defer domain removal if device is assigned to a driver
Alex Deucher [Thu, 21 Aug 2014 14:55:07 +0000 (10:55 -0400)]
drm/radeon: add additional SI pci ids
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Alex Deucher [Thu, 21 Aug 2014 14:48:11 +0000 (10:48 -0400)]
drm/radeon: add new bonaire pci ids
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Alex Deucher [Thu, 21 Aug 2014 14:41:42 +0000 (10:41 -0400)]
drm/radeon: add new KV pci id
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=82912
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Ingo Molnar [Fri, 22 Aug 2014 08:04:15 +0000 (10:04 +0200)]
Merge tag 'efi-urgent' of git://git./linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fixes from Matt Fleming:
* WARN_ON(!spin_is_locked()) always triggers on non-SMP machines.
Swap it for the more canonical lockdep_assert_held() which always
does the right thing - Guenter Roeck
* Assign the correct value to efi.runtime_version on arm64 so that all
the runtime services can be invoked - Semen Protsenko
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Semen Protsenko [Fri, 15 Aug 2014 13:22:44 +0000 (16:22 +0300)]
efi/arm64: Store Runtime Services revision
"efi" global data structure contains "runtime_version" field which must
be assigned in order to use it later in Runtime Services virtual calls
(virt_efi_* functions).
Before this patch "runtime_version" was unassigned (0), so each
Runtime Service virtual call that checks revision would fail.
Signed-off-by: Semen Protsenko <semen.protsenko@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Guenter Roeck [Wed, 13 Aug 2014 18:21:34 +0000 (11:21 -0700)]
firmware: Do not use WARN_ON(!spin_is_locked())
spin_is_locked() always returns false for uniprocessor configurations
in several architectures, so do not use WARN_ON with it.
Use lockdep_assert_held() instead to also reduce overhead in
non-debug kernels.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Hariprasad Shenai [Thu, 21 Aug 2014 11:34:46 +0000 (17:04 +0530)]
cxgb4: Free completed tx skbs promptly
Description of problem:
The NIC card is not reporting back to the driver the transmitted skbs,
so they get stuck in the TX ring causing issues with reference
counters in other kernel components.
Developed a new Automatic Egress Queue Update firmware facility to slowly tick
through Egress Queues and send back any outstanding CIDX Updates which are
laying around.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 22 Aug 2014 04:53:15 +0000 (21:53 -0700)]
Merge tag 'linux-can-fixes-for-3.17-
20140821' of git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2014-08-21
The first patch is from Mirza Krak, it fixes the initialization of the hardware
in the sja1000 driver. The next patch is contributed by Dan Carpenter, it fixes
the error handling in the c_can's probe function. Then there are two patches
for the flexcan driver, one by Alexander Stein, which fixes the resetting of
the bus error interrupt mask, the other one by Sebastian Andrzej Siewior which
adds an additional error state transition message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Anish Bhatt [Wed, 20 Aug 2014 20:44:06 +0000 (13:44 -0700)]
cxgb4: Fix race condition in cleanup
There is a possible race condition when we unregister the PCI Driver and then
flush/destroy the global "workq". This could lead to situations where there
are tasks on the Work Queue with references to now deleted adapter data
structures. Instead, have per-adapter Work Queues which were instantiated and
torn down in init_one() and remove_one(), respectively.
v2: Remove unnecessary call to flush_workqueue() before destroy_workqueue()
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
zhuyj [Wed, 20 Aug 2014 09:31:43 +0000 (17:31 +0800)]
sctp: not send SCTP_PEER_ADDR_CHANGE notifications with failed probe
Since the transport has always been in state SCTP_UNCONFIRMED, it
therefore wasn't active before and hasn't been used before, and it
always has been, so it is unnecessary to bug the user with a
notification.
Reported-by: Deepak Khandelwal <khandelwal.deepak.1987@gmail.com>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Suggested-by: Michael Tuexen <tuexen@fh-muenster.de>
Suggested-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Zhu Yanjun <Yanjun.Zhu@windriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Wed, 20 Aug 2014 13:39:22 +0000 (15:39 +0200)]
sh: intc: Confine SH_INTC to platforms that need it
Currently the sh-intc driver is compiled on all SuperH and
non-multiplatform SH-Mobile platforms, while it's only used on a limited
number of platforms:
- SuperH: SH2(A), SH3(A), SH4(A)(L) (all but SH5)
- ARM: sh7372, sh73a0
Drop the "default y" on SH_INTC, make all CPU platforms that use it
select it, and protect all sub-options by "if SH_INTC" to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Yuval Mintz [Mon, 18 Aug 2014 19:36:23 +0000 (22:36 +0300)]
bnx2x: Revert UNDI flushing mechanism
Commit
91ebb929b6f8 ("bnx2x: Add support for Multi-Function UNDI") [which was
later supposedly fixed by
de682941eef3 ("bnx2x: Fix UNDI driver unload")]
introduced a bug in which in some [yet-to-be-determined] scenarios the
alternative flushing mechanism which was to guarantee the Rx buffers are
empty before resetting them during device probe will fail.
If this happens, when device will be loaded once more a fatal attention will
occur; Since this most likely happens in boot from SAN scenarios, the machine
will fail to load.
Notice this may occur not only in the 'Multi-Function' scenario but in the
regular scenario as well, i.e., this introduced a regression in the driver's
ability to perform boot from SAN.
The patch reverts the mechanism and applies the old scheme to multi-function
devices as well as to single-function devices.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 22 Aug 2014 00:43:20 +0000 (17:43 -0700)]
Merge branch 'qlcnic'
Shahed Shaikh says:
====================
qlcnic: Bug fixes
This series fixes some bugs related to endianess.
Please apply this series to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shahed Shaikh [Mon, 18 Aug 2014 13:31:55 +0000 (09:31 -0400)]
qlcnic: Fix endianess issue in firmware load from file operation
Firmware binary file is in little endian. On big-endian architecture, while
writing this binary FW file to adapters memory, writel() swaps the data resulting into
corruption of FW image. So, swap the data before writing into adapters memory.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rajesh Borundia [Mon, 18 Aug 2014 13:31:54 +0000 (09:31 -0400)]
qlcnic: Fix endianess issue in FW dump template header
Firmware dump template header is read from adapter using
readl() which swaps the data. So, adjust structure
element on the boundary of 32bit dword.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jitendra Kalsaria [Mon, 18 Aug 2014 13:31:53 +0000 (09:31 -0400)]
qlcnic: Fix flash access interface to application
Application expects flash data in little endian, but driver reads/writes
flash data using readl()/writel() APIs which swaps data on big endian machine.
So, swap the data after reading from and before writing to flash memory.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Ott [Sat, 16 Aug 2014 21:09:03 +0000 (17:09 -0400)]
MAINTAINERS: Add section for MRF24J40 IEEE 802.15.4 radio driver
Alan is the original author of the driver. This change was discussed
with the 802.15.4 subsystem maintainer, Alexander Aring.
Signed-off-by: Alan Ott <alan@signal11.us>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Fri, 15 Aug 2014 17:04:59 +0000 (13:04 -0400)]
macvlan: Allow setting multicast filter on all macvlan types
Currently, macvlan code restricts multicast and unicast
filter setting only to passthru devices. As a result,
if a guest using macvtap wants to receive multicast
traffic, it has to set IFF_ALLMULTI or IFF_PROMISC.
This patch makes it possible to use the fdb interface
to add multicast addresses to the filter thus allowing
a guest to receive only targeted multicast traffic.
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 15 Aug 2014 16:16:04 +0000 (09:16 -0700)]
packet: handle too big packets for PACKET_V3
af_packet can currently overwrite kernel memory by out of bound
accesses, because it assumed a [new] block can always hold one frame.
This is not generally the case, even if most existing tools do it right.
This patch clamps too long frames as API permits, and issue a one time
error on syslog.
[ 394.357639] tpacket_rcv: packet too big, clamped from 5042 to 3966. macoff=82
In this example, packet header tp_snaplen was set to 3966,
and tp_len was set to 5042 (skb->len)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes:
f6fb8f100b80 ("af-packet: TPACKET_V3 flexible buffer implementation.")
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dariusz Marcinkiewicz [Fri, 15 Aug 2014 15:50:47 +0000 (17:50 +0200)]
MAINTAINERS: add entry for ec_bhf driver
Added entry for ec_bhf driver.
Signed-off-by: Dariusz Marcinkiewicz <reksio@newterm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
chas williams - CONTRACTOR [Thu, 14 Aug 2014 13:19:47 +0000 (09:19 -0400)]
lec: Use rtnl lock/unlock when updating MTU
The LECS response contains the MTU that should be used. Correctly
synchronize with other layers when updating.
Signed-off-by: Chas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Airlie [Thu, 21 Aug 2014 21:29:52 +0000 (07:29 +1000)]
Merge tag 'drm-intel-fixes-2014-08-21' of git://anongit.freedesktop.org/drm-intel
Display fixes from Ville and Imre, all cc: stable.
* tag 'drm-intel-fixes-2014-08-21' of git://anongit.freedesktop.org/drm-intel:
drm/i915: don't try to retrain a DP link on an inactive CRTC
drm/i915: make sure VDD is turned off during system suspend
drm/i915: cancel hotplug and dig_port work during suspend and unload
drm/i915: fix HPD IRQ reenable work cancelation
drm/i915: take display port power domain in DP HPD handler
drm/i915: Don't try to enable cursor from setplane when crtc is disabled
drm/i915: Skip load detect when intel_crtc->new_enable==true
drm/i915: Fix locking for intel_enable_pipe_a()
Dave Airlie [Thu, 21 Aug 2014 21:29:25 +0000 (07:29 +1000)]
Merge branch 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux
more radeon fixes
* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
Revert "drm/radeon: Use write-combined CPU mappings of ring buffers with PCIe"
drm/radeon: fix active_cu mask on SI and CIK after re-init (v3)
drm/radeon: fix active cu count for SI and CIK
drm/radeon: re-enable selective GPUVM flushing
drm/radeon: Sync ME and PFP after CP semaphore waits v4
drm/radeon: fix display handling in radeon_gpu_reset
drm/radeon: fix pm handling in radeon_gpu_reset
drm/radeon: Only flush HDP cache for indirect buffers from userspace
drm/radeon: properly document reloc priority mask
Linus Torvalds [Thu, 21 Aug 2014 21:26:27 +0000 (14:26 -0700)]
Merge branch 'for-3.17-fixes' of git://git./linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Nothing drastic but pushing out early due to build breakage in the new
tegra platform.
Additionally:
- M550 tagged trim blacklist pattern is widened so that it matches
the new 1TB model
- three controller specific fixes"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: widen Crucial M550 blacklist matching
pata_scc: propagate return value of scc_wait_after_reset
ata: ahci_tegra: Change include to fix compilation
pata_samsung_cf: change ret type to signed
ahci_xgene: Removing NCQ support from the APM X-Gene SoC AHCI SATA Host Controller driver.
Linus Torvalds [Thu, 21 Aug 2014 21:25:20 +0000 (14:25 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fixes for a couple potential memory corruption problems (the HW would
have to be manufactured to be deliberately evil to trigger those)
found by Ben Hawkes
- fix for potential infinite loop when using sysfs interface of
logitech driver, from Simon Wood
- a couple more simple driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: fix a couple of off-by-ones
HID: logitech: perform bounds checking on device_id early enough
HID: logitech: fix bounds checking on LED report size
HID: logitech: Prevent possibility of infinite loop when using /sys interface
HID: rmi: print an error if F11 is not found instead of stopping the device
HID: hid-sensor-hub: use devm_ functions consistently
HID: huion: Use allocated buffer for DMA
HID: huion: Fail on parameter retrieval errors
Linus Torvalds [Thu, 21 Aug 2014 21:24:40 +0000 (14:24 -0700)]
Merge tag 'sound-3.17-rc2' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A bunch of ASoC fixes with a few HD-audio fixes in this pull request.
All fairly small, boring and device-specific fixes, in addition to
MAINTAINERS update for better reviewing"
* tag 'sound-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/hdmi - apply Valleyview fix-ups to Cherryview display codec
ALSA: hda/hdmi - set depop_delay for haswell plus
ALSA: hda - restore the gpio led after resume
ALSA: hda/realtek - Avoid setting wrong COEF on ALC269 & co
ASoC: pxa-ssp: drop SNDRV_PCM_FMTBIT_S24_LE
ASoC: fsl-esai: Revert .xlate_tdm_slot_mask() support
ASoC: mcasp: Fix implicit BLCK divider setting
ASoC: arizona: Fix TDM slot length handling in arizona_hw_params
ASoC: pcm512x: Correct Digital Playback control names
ASoC: dapm: Fix uninitialized variable in snd_soc_dapm_get_enum_double()
ASoC: Intel: Restore Baytrail ADSP streams only when ADSP was in reset
ASoC: Intel: Wait Baytrail ADSP boot at resume_early stage
ASoC: Intel: Merge Baytrail ADSP suspend_noirq into suspend_late
MAINTAINERS: Add i.MX maintainers and paths to Freescale ASoC entry
ASoC: Intel: Update Baytrail ADSP firmware name
Linus Torvalds [Thu, 21 Aug 2014 21:07:44 +0000 (14:07 -0700)]
Merge branch 'i2c/for-next' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here is the fixup for the 'lowlight' of my last pull request. I2C is
not selected anymore by I2C_ACPI. Instead, the code in question now
depends on I2C=y.
Also, Mika has agreed to support me and be the maintainer for I2C-ACPI
related patches. Finally, a new-ID-patch came along last week"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer for ACPI parts of I2C
i2c: i801: Add PCI ID for Intel Braswell
i2c: rework kernel config I2C_ACPI
Linus Torvalds [Thu, 21 Aug 2014 21:06:56 +0000 (14:06 -0700)]
Merge tag 'please-pull-memfd_create' of git://git./linux/kernel/git/aegl/linux
Pull ia64 update from Tony Luck:
"Add memfd_create syscall to ia64"
* tag 'please-pull-memfd_create' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] Wire up memfd_create() system call
Linus Torvalds [Thu, 21 Aug 2014 21:06:18 +0000 (14:06 -0700)]
Merge tag 'microblaze-3.17-rc2' of git://git.monstr.eu/linux-2.6-microblaze
Pull microblaze update from Michal Simek:
"Wire-up seccomp/getrandom/memfd_create syscalls"
* tag 'microblaze-3.17-rc2' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Wire-up memfd_create syscall
microblaze: Wire-up getrandom syscall
microblaze: Wire-up seccomp syscall
Jiri Kosina [Thu, 21 Aug 2014 14:57:48 +0000 (09:57 -0500)]
HID: fix a couple of off-by-ones
There are a few very theoretical off-by-one bugs in report descriptor size
checking when performing a pre-parsing fixup. Fix those.
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jiri Kosina [Thu, 21 Aug 2014 14:57:17 +0000 (09:57 -0500)]
HID: logitech: perform bounds checking on device_id early enough
device_index is a char type and the size of paired_dj_deivces is 7
elements, therefore proper bounds checking has to be applied to
device_index before it is used.
We are currently performing the bounds checking in
logi_dj_recv_add_djhid_device(), which is too late, as malicious device
could send REPORT_TYPE_NOTIF_DEVICE_UNPAIRED early enough and trigger the
problem in one of the report forwarding functions called from
logi_dj_raw_event().
Fix this by performing the check at the earliest possible ocasion in
logi_dj_raw_event().
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jiri Kosina [Thu, 21 Aug 2014 14:56:47 +0000 (09:56 -0500)]
HID: logitech: fix bounds checking on LED report size
The check on report size for REPORT_TYPE_LEDS in logi_dj_ll_raw_request()
is wrong; the current check doesn't make any sense -- the report allocated
by HID core in hid_hw_raw_request() can be much larger than
DJREPORT_SHORT_LENGTH, and currently logi_dj_ll_raw_request() doesn't
handle this properly at all.
Fix the check by actually trimming down the report size properly if it is
too large.
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Mathias Nyman [Tue, 19 Aug 2014 11:00:01 +0000 (14:00 +0300)]
gpio-lynxpoint: enable input sensing in resume
It appears that input sensing bit might be reset during
suspend/resume. Set input sensing again for all requested gpios
in resume
Tested-by: Jerome Blin <jerome.blin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 19 Aug 2014 17:00:53 +0000 (12:00 -0500)]
gpio: move GPIOD flags outside #ifdef
The GPIOD flags are defined inside the #ifdef CONFIG_GPIOLIB
switch, making the gpiolib stubs fail if these flags are used
by a consumer. This is not correct: the stubs should compile
fine without GPIOLIB.
Reported-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sebastian Andrzej Siewior [Fri, 25 Jul 2014 18:16:40 +0000 (20:16 +0200)]
can: flexcan: handle state passive -> warning transition
Once the CAN-bus is open and a packet is sent, the controller switches
into the PASSIVE state. Once the BUS is closed again it goes the back
err-warning. The TX error counter goes 0 -> 0x80 -> 0x7f.
This patch makes sure that the user learns about this state chang
(CAN_STATE_ERROR_WARNING => CAN_STATE_ERROR_PASSIVE)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Matthias Klein <matthias.klein@optimeas.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Alexander Stein [Tue, 12 Aug 2014 08:47:21 +0000 (10:47 +0200)]
can: flexcan: Disable error interrupt when bus error reporting is disabled
In case we don't have FLEXCAN_HAS_BROKEN_ERR_STATE and the user set
CAN_CTRLMODE_BERR_REPORTING once it can not be unset again until reboot.
So in case neither hardware nor user wants the error interrupt disable
the bit.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Dan Carpenter [Fri, 1 Aug 2014 08:53:44 +0000 (11:53 +0300)]
can: c_can: checking IS_ERR() instead of NULL
devm_ioremap() returns NULL on error, not an ERR_PTR().
Fixes:
33cf75656923 ('can: c_can_platform: Fix raminit, use devm_ioremap() instead of devm_ioremap_resource()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Mirza Krak [Fri, 8 Aug 2014 12:30:50 +0000 (14:30 +0200)]
can: sja1000: Validate initialization state in start method
When sja1000 is not compiled as module the SJA1000 chip is only
initialized during device registration on kernel boot. Should the chip
get a hardware reset there is no way to reinitialize it without re-
booting the Linux kernel.
This patch adds a check in sja1000_start if the chip is initialized, if
not we initialize it.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Michal Simek [Thu, 21 Aug 2014 08:19:28 +0000 (10:19 +0200)]
microblaze: Wire-up memfd_create syscall
Add new memfd_create syscall.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 7 Aug 2014 13:59:05 +0000 (15:59 +0200)]
microblaze: Wire-up getrandom syscall
Add new getrandom syscall.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 7 Aug 2014 13:57:41 +0000 (15:57 +0200)]
microblaze: Wire-up seccomp syscall
Add new seccomp syscall.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Linus Torvalds [Wed, 20 Aug 2014 23:33:21 +0000 (18:33 -0500)]
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Most important fixes in this set include three SMB3 fixes for stable
(including fix for possible kernel oops), and a workaround to allow
writes to Mac servers (only cifs dialect, not more current SMB2.1,
worked to Mac servers). Also fallocate support added, and lease fix
from Jeff"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
[SMB3] Enable fallocate -z support for SMB3 mounts
enable fallocate punch hole ("fallocate -p") for SMB3
Incorrect error returned on setting file compressed on SMB2
CIFS: Fix wrong directory attributes after rename
CIFS: Fix SMB2 readdir error handling
[CIFS] Possible null ptr deref in SMB2_tcon
[CIFS] Workaround MacOS server problem with SMB2.1 write response
cifs: handle lease F_UNLCK requests properly
Cleanup sparse file support by creating worker function for it
Add sparse file support to SMB2/SMB3 mounts
Add missing definitions for CIFS File System Attributes
cifs: remove unused function cifs_oplock_break_wait
Linus Torvalds [Wed, 20 Aug 2014 23:32:16 +0000 (18:32 -0500)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-fs
Pull filesystem fixes from Jan Kara:
"udf, isofs, and ext3 bug fixes"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext3: Count internal journal as bsddf overhead in ext3_statfs
isofs: Fix unbounded recursion when processing relocated directories
udf: avoid unneeded up_write when fail to add entry in ->symlink