OSDN Git Service
Srinivas Neeli [Thu, 21 Jul 2022 07:39:09 +0000 (13:09 +0530)]
gpio: gpio-xilinx: Fix integer overflow
Current implementation is not able to configure more than 32 pins
due to incorrect data type. So type casting with unsigned long
to avoid it.
Fixes:
02b3f84d9080 ("xilinx: Switch to use bitmap APIs")
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Kent Gibson [Tue, 19 Jul 2022 11:06:01 +0000 (19:06 +0800)]
selftests: gpio: fix include path to kernel headers for out of tree builds
When building selftests out of the kernel tree the gpio.h the include
path is incorrect and the build falls back to the system includes
which may be outdated.
Add the KHDR_INCLUDES to the CFLAGS to include the gpio.h from the
build tree.
Fixes:
4f4d0af7b2d9 ("selftests: gpio: restore CFLAGS options")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Haibo Chen [Mon, 18 Jul 2022 08:31:43 +0000 (16:31 +0800)]
gpio: pca953x: use the correct register address when regcache sync during init
For regcache_sync_region, we need to use pca953x_recalc_addr() to get
the real register address.
Fixes:
ec82d1eba346 ("gpio: pca953x: Zap ad-hoc reg_output cache")
Fixes:
0f25fda840a9 ("gpio: pca953x: Zap ad-hoc reg_direction cache")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Haibo Chen [Mon, 18 Jul 2022 08:31:42 +0000 (16:31 +0800)]
gpio: pca953x: use the correct range when do regmap sync
regmap will sync a range of registers, here use the correct range
to make sure the sync do not touch other unexpected registers.
Find on pca9557pw on imx8qxp/dxl evk board, this device support
8 pin, so only need one register(8 bits) to cover all the 8 pins's
property setting. But when sync the output, we find it actually
update two registers, output register and the following register.
Fixes:
b76574300504 ("gpio: pca953x: Restore registers after suspend/resume cycle")
Fixes:
ec82d1eba346 ("gpio: pca953x: Zap ad-hoc reg_output cache")
Fixes:
0f25fda840a9 ("gpio: pca953x: Zap ad-hoc reg_direction cache")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Haibo Chen [Mon, 18 Jul 2022 08:31:41 +0000 (16:31 +0800)]
gpio: pca953x: only use single read/write for No AI mode
For the device use NO AI mode(not support auto address increment),
only use the single read/write when config the regmap.
We meet issue on PCA9557PW on i.MX8QXP/DXL evk board, this device
do not support AI mode, but when do the regmap sync, regmap will
sync 3 byte data to register 1, logically this means write first
data to register 1, write second data to register 2, write third data
to register 3. But this device do not support AI mode, finally, these
three data write only into register 1 one by one. the reault is the
value of register 1 alway equal to the latest data, here is the third
data, no operation happened on register 2 and register 3. This is
not what we expect.
Fixes:
49427232764d ("gpio: pca953x: Perform basic regmap conversion")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Linus Torvalds [Sun, 17 Jul 2022 20:30:22 +0000 (13:30 -0700)]
Linux 5.19-rc7
Linus Torvalds [Sun, 17 Jul 2022 20:08:03 +0000 (13:08 -0700)]
Merge tag 'drm-intel-fixes-2022-07-17' of git://anongit.freedesktop.org/drm/drm-intel
Pull intel drm build fix from Rodrigo Vivi:
"Our 'dim' flow has a problem with fixes of fixes getting missed. We
need to take a look on that later.
Meanwhile, please allow me to quickly propagate this fix for the
32-bit build issue here upstream"
* tag 'drm-intel-fixes-2022-07-17' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915/ttm: fix 32b build
Linus Torvalds [Sun, 17 Jul 2022 19:42:57 +0000 (12:42 -0700)]
Merge tag 'perf-tools-fixes-for-v5.19-2022-07-17' of git://git./linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix SIGSEGV when processing syscall args in perf.data files in 'perf
trace'
- Sync kvm, msr-index and cpufeatures headers with the kernel sources
- Fix 'convert perf time to TSC' 'perf test':
- No need to open events twice
- Fix finding correct event on hybrid systems
* tag 'perf-tools-fixes-for-v5.19-2022-07-17' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf trace: Fix SIGSEGV when processing syscall args
perf tests: Fix Convert perf time to TSC test for hybrid
perf tests: Stop Convert perf time to TSC test opening events twice
tools arch x86: Sync the msr-index.h copy with the kernel sources
tools headers cpufeatures: Sync with the kernel sources
tools headers UAPI: Sync linux/kvm.h with the kernel sources
Matthew Auld [Tue, 12 Jul 2022 17:40:50 +0000 (18:40 +0100)]
drm/i915/ttm: fix 32b build
Since segment_pages is no longer a compile time constant, it looks the
DIV_ROUND_UP(node->size, segment_pages) breaks the 32b build. Simplest
is just to use the ULL variant, but really we should need not need more
than u32 for the page alignment (also we are limited by that due to the
sg->length type), so also make it all u32.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes:
aff1e0b09b54 ("drm/i915/ttm: fix sg_table construction")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Nirmoy Das <nirmoy.das@linux.intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220712174050.592550-1-matthew.auld@intel.com
(cherry picked from commit
9306b2b2dfce6931241ef804783692cee526599c)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Linus Torvalds [Sun, 17 Jul 2022 15:34:02 +0000 (08:34 -0700)]
Merge tag 'perf_urgent_for_v5.19_rc7' of git://git./linux/kernel/git/tip/tip
Pull perf fix from Borislav Petkov:
- A single data race fix on the perf event cleanup path to avoid
endless loops due to insufficient locking
* tag 'perf_urgent_for_v5.19_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix data race between perf_event_set_output() and perf_mmap_close()
Linus Torvalds [Sun, 17 Jul 2022 15:27:30 +0000 (08:27 -0700)]
Merge tag 'x86_urgent_for_v5.19_rc7' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Improve the check whether the kernel supports WP mappings so that it
can accomodate a XenPV guest due to how the latter is setting up the
PAT machinery
- Now that the retbleed nightmare is public, here's the first round of
fallout fixes:
* Fix a build failure on 32-bit due to missing include
* Remove an untraining point in espfix64 return path
* other small cleanups
* tag 'x86_urgent_for_v5.19_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/bugs: Remove apostrophe typo
um: Add missing apply_returns()
x86/entry: Remove UNTRAIN_RET from native_irq_return_ldt
x86/bugs: Mark retbleed_strings static
x86/pat: Fix x86_has_pat_wp()
x86/asm/32: Fix ANNOTATE_UNRET_SAFE use on 32-bit
Linus Torvalds [Sun, 17 Jul 2022 14:58:19 +0000 (07:58 -0700)]
Merge tag 'gpio-fixes-for-v5.19-rc7' of git://git./linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
- fix a configfs attribute of the gpio-sim module
* tag 'gpio-fixes-for-v5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: sim: fix the chip_name configfs item
Linus Torvalds [Sun, 17 Jul 2022 14:52:46 +0000 (07:52 -0700)]
Merge tag 'input-for-v5.19-rc6' of git://git./linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- fix Goodix driver to properly behave on the Aya Neo Next
- some more sanity checks in usbtouchscreen driver
- a tweak in wm97xx driver in preparation for remove() to return void
- a clarification in input core regarding units of measurement for
resolution on touch events.
* tag 'input-for-v5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: document the units for resolution of size axes
Input: goodix - call acpi_device_fix_up_power() in some cases
Input: wm97xx - make .remove() obviously always return 0
Input: usbtouchscreen - add driver_info sanity check
Linus Torvalds [Sun, 17 Jul 2022 14:45:51 +0000 (07:45 -0700)]
Merge tag 'for-v5.19-rc' of git://git./linux/kernel/git/sre/linux-power-supply
Pull power supply fixes from Sebastian Reichel:
- power-supply core temperature interpolation regression fix for
incorrect boundaries
- ab8500 needs to destroy its work queues in error paths
- Fix old DT refcount leak in arm-versatile
* tag 'for-v5.19-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: supply: core: Fix boundary conditions in interpolation
power/reset: arm-versatile: Fix refcount leak in versatile_reboot_probe
power: supply: ab8500_fg: add missing destroy_workqueue in ab8500_fg_probe
Naveen N. Rao [Thu, 7 Jul 2022 09:09:00 +0000 (14:39 +0530)]
perf trace: Fix SIGSEGV when processing syscall args
On powerpc, 'perf trace' is crashing with a SIGSEGV when trying to
process a perf.data file created with 'perf trace record -p':
#0 0x00000001225b8988 in syscall_arg__scnprintf_augmented_string <snip> at builtin-trace.c:1492
#1 syscall_arg__scnprintf_filename <snip> at builtin-trace.c:1492
#2 syscall_arg__scnprintf_filename <snip> at builtin-trace.c:1486
#3 0x00000001225bdd9c in syscall_arg_fmt__scnprintf_val <snip> at builtin-trace.c:1973
#4 syscall__scnprintf_args <snip> at builtin-trace.c:2041
#5 0x00000001225bff04 in trace__sys_enter <snip> at builtin-trace.c:2319
That points to the below code in tools/perf/builtin-trace.c:
/*
* If this is raw_syscalls.sys_enter, then it always comes with the 6 possible
* arguments, even if the syscall being handled, say "openat", uses only 4 arguments
* this breaks syscall__augmented_args() check for augmented args, as we calculate
* syscall->args_size using each syscalls:sys_enter_NAME tracefs format file,
* so when handling, say the openat syscall, we end up getting 6 args for the
* raw_syscalls:sys_enter event, when we expected just 4, we end up mistakenly
* thinking that the extra 2 u64 args are the augmented filename, so just check
* here and avoid using augmented syscalls when the evsel is the raw_syscalls one.
*/
if (evsel != trace->syscalls.events.sys_enter)
augmented_args = syscall__augmented_args(sc, sample, &augmented_args_size, trace->raw_augmented_syscalls_args_size);
As the comment points out, we should not be trying to augment the args
for raw_syscalls. However, when processing a perf.data file, we are not
initializing those properly. Fix the same.
Reported-by: Claudio Carvalho <cclaudio@linux.ibm.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/20220707090900.572584-1-naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adrian Hunter [Wed, 13 Jul 2022 12:34:59 +0000 (15:34 +0300)]
perf tests: Fix Convert perf time to TSC test for hybrid
The test does not always correctly determine the number of events for
hybrids, nor allow for more than 1 evsel when parsing.
Fix by iterating the events actually created and getting the correct
evsel for the events processed.
Fixes:
d9da6f70eb235110 ("perf tests: Support 'Convert perf time to TSC' test for hybrid")
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Link: https://lore.kernel.org/r/20220713123459.24145-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adrian Hunter [Wed, 13 Jul 2022 12:34:58 +0000 (15:34 +0300)]
perf tests: Stop Convert perf time to TSC test opening events twice
Do not call evlist__open() twice.
Fixes:
5bb017d4b97a0f13 ("perf test: Fix error message for test case 71 on s390, where it is not supported")
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Link: https://lore.kernel.org/r/20220713123459.24145-2-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Thu, 1 Jul 2021 16:32:18 +0000 (13:32 -0300)]
tools arch x86: Sync the msr-index.h copy with the kernel sources
To pick up the changes from these csets:
4ad3278df6fe2b08 ("x86/speculation: Disable RRSBA behavior")
d7caac991feeef1b ("x86/cpu/amd: Add Spectral Chicken")
That cause no changes to tooling:
$ tools/perf/trace/beauty/tracepoints/x86_msr.sh > before
$ cp arch/x86/include/asm/msr-index.h tools/arch/x86/include/asm/msr-index.h
$ tools/perf/trace/beauty/tracepoints/x86_msr.sh > after
$ diff -u before after
$
Just silences this perf build warning:
Warning: Kernel ABI header at 'tools/arch/x86/include/asm/msr-index.h' differs from latest version at 'arch/x86/include/asm/msr-index.h'
diff -u tools/arch/x86/include/asm/msr-index.h arch/x86/include/asm/msr-index.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/lkml/YtQTm9wsB3hxQWvy@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Thu, 1 Jul 2021 16:39:15 +0000 (13:39 -0300)]
tools headers cpufeatures: Sync with the kernel sources
To pick the changes from:
f43b9876e857c739 ("x86/retbleed: Add fine grained Kconfig knobs")
a149180fbcf336e9 ("x86: Add magic AMD return-thunk")
15e67227c49a5783 ("x86: Undo return-thunk damage")
369ae6ffc41a3c11 ("x86/retpoline: Cleanup some #ifdefery")
4ad3278df6fe2b08 x86/speculation: Disable RRSBA behavior
26aae8ccbc197223 x86/cpu/amd: Enumerate BTC_NO
9756bba28470722d x86/speculation: Fill RSB on vmexit for IBRS
3ebc170068885b6f x86/bugs: Add retbleed=ibpb
2dbb887e875b1de3 x86/entry: Add kernel IBRS implementation
6b80b59b35557065 x86/bugs: Report AMD retbleed vulnerability
a149180fbcf336e9 x86: Add magic AMD return-thunk
15e67227c49a5783 x86: Undo return-thunk damage
a883d624aed463c8 x86/cpufeatures: Move RETPOLINE flags to word 11
51802186158c74a0 x86/speculation/mmio: Enumerate Processor MMIO Stale Data bug
This only causes these perf files to be rebuilt:
CC /tmp/build/perf/bench/mem-memcpy-x86-64-asm.o
CC /tmp/build/perf/bench/mem-memset-x86-64-asm.o
And addresses this perf build warning:
Warning: Kernel ABI header at 'tools/arch/x86/include/asm/cpufeatures.h' differs from latest version at 'arch/x86/include/asm/cpufeatures.h'
diff -u tools/arch/x86/include/asm/cpufeatures.h arch/x86/include/asm/cpufeatures.h
Warning: Kernel ABI header at 'tools/arch/x86/include/asm/disabled-features.h' differs from latest version at 'arch/x86/include/asm/disabled-features.h'
diff -u tools/arch/x86/include/asm/disabled-features.h arch/x86/include/asm/disabled-features.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org
Link: https://lore.kernel.org/lkml/YtQM40VmiLTkPND2@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Sun, 9 May 2021 12:39:02 +0000 (09:39 -0300)]
tools headers UAPI: Sync linux/kvm.h with the kernel sources
To pick the changes in:
1b870fa5573e260b ("kvm: stats: tell userspace which values are boolean")
That just rebuilds perf, as these patches don't add any new KVM ioctl to
be harvested for the the 'perf trace' ioctl syscall argument
beautifiers.
This is also by now used by tools/testing/selftests/kvm/, a simple test
build succeeded.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/kvm.h' differs from latest version at 'include/uapi/linux/kvm.h'
diff -u tools/include/uapi/linux/kvm.h include/uapi/linux/kvm.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Link: http://lore.kernel.org/lkml/YtQLDvQrBhJNl3n5@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Linus Torvalds [Sat, 16 Jul 2022 20:48:55 +0000 (13:48 -0700)]
Merge tag 'for-5.19-rc7-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs reverts from David Sterba:
"Due to a recent report [1] we need to revert the radix tree to xarray
conversion patches.
There's a problem with sleeping under spinlock, when xa_insert could
allocate memory under pressure. We use GFP_NOFS so this is a real
problem that we unfortunately did not discover during review.
I'm sorry to do such change at rc6 time but the revert is IMO the
safer option, there are patches to use mutex instead of the spin locks
but that would need more testing. The revert branch has been tested on
a few setups, all seem ok.
The conversion to xarray will be revisited in the future"
Link: https://lore.kernel.org/linux-btrfs/cover.1657097693.git.fdmanana@suse.com/
* tag 'for-5.19-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Revert "btrfs: turn delayed_nodes_tree into an XArray"
Revert "btrfs: turn name_cache radix tree into XArray in send_ctx"
Revert "btrfs: turn fs_info member buffer_radix into XArray"
Revert "btrfs: turn fs_roots_radix in btrfs_fs_info into an XArray"
Linus Torvalds [Sat, 16 Jul 2022 18:45:40 +0000 (11:45 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six small and reasonably obvious fixes, all in drivers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: pm80xx: Set stopped phy's linkrate to Disabled
scsi: pm80xx: Fix 'Unknown' max/min linkrate
scsi: ufs: core: Fix missing clk change notification on host reset
scsi: ufs: core: Drop loglevel of WriteBoost message
scsi: megaraid: Clear READ queue map's nr_queues
scsi: target: Fix WRITE_SAME No Data Buffer crash
Linus Torvalds [Sat, 16 Jul 2022 18:40:10 +0000 (11:40 -0700)]
Merge tag 'block-5.19-2022-07-15' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Two NVMe fixes, and a regression fix for the core block layer from
this merge window"
* tag 'block-5.19-2022-07-15' of git://git.kernel.dk/linux-block:
block: fix missing blkcg_bio_issue_init
nvme: fix block device naming collision
nvme-pci: fix freeze accounting for error handling
Linus Torvalds [Sat, 16 Jul 2022 18:21:15 +0000 (11:21 -0700)]
Merge tag 'usb-5.19-rc7' of git://git./linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are some small USB driver fixes and new device ids for 5.19-rc7.
They include:
- new usb-serial driver ids
- typec uevent fix
- uvc gadget driver fix
- dwc3 driver fixes
- ehci-fsl driver fix
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: ftdi_sio: add Belimo device ids
drivers/usb/host/ehci-fsl: Fix interrupt setup in host mode.
usb: gadget: uvc: fix changing interface name via configfs
usb: typec: add missing uevent when partner support PD
usb: dwc3-am62: remove unnecesary clk_put()
usb: dwc3: gadget: Fix event pending check
Linus Torvalds [Sat, 16 Jul 2022 18:11:56 +0000 (11:11 -0700)]
Merge tag 'tty-5.19-rc7' of git://git./linux/kernel/git/gregkh/tty
Pull tty and serial driver fixes from Greg KH:
"Here are some TTY and Serial driver fixes for 5.19-rc7. They resolve a
number of reported problems including:
- longtime bug in pty_write() that has been reported in the past.
- 8250 driver fixes
- new serial device ids
- vt overlapping data copy bugfix
- other tiny serial driver bugfixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: use new tty_insert_flip_string_and_push_buffer() in pty_write()
tty: extract tty_flip_buffer_commit() from tty_flip_buffer_push()
serial: 8250: dw: Fix the macro RZN1_UART_xDMACR_8_WORD_BURST
vt: fix memory overlapping when deleting chars in the buffer
serial: mvebu-uart: correctly report configured baudrate value
serial: 8250: Fix PM usage_count for console handover
serial: 8250: fix return error code in serial8250_request_std_resource()
serial: stm32: Clear prev values before setting RTS delays
tty: Add N_CAN327 line discipline ID for ELM327 based CAN driver
serial: 8250: Fix __stop_tx() & DMA Tx restart races
serial: pl011: UPSTAT_AUTORTS requires .throttle/unthrottle
tty: serial: samsung_tty: set dma burst_size to 1
serial: 8250: dw: enable using pdata with ACPI
Linus Torvalds [Sat, 16 Jul 2022 18:00:40 +0000 (11:00 -0700)]
Merge tag 's390-5.19-6' of git://git./linux/kernel/git/s390/linux
Pull s390 fixes from Alexander Gordeev:
- Fix building of out-of-tree kernel modules without a pre-built kernel
in case CONFIG_EXPOLINE_EXTERN=y.
- Fix a reference counting error that could prevent unloading of zcrypt
modules.
* tag 's390-5.19-6' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ap: fix error handling in __verify_queue_reservations()
s390/nospec: remove unneeded header includes
s390/nospec: build expoline.o for modules_prepare target
Linus Torvalds [Sat, 16 Jul 2022 17:56:28 +0000 (10:56 -0700)]
Merge tag 'pm-5.19-rc7' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki
"Fix recent regression in the cpufreq mediatek driver related to
incorrect handling of regulator_get_optional() return value
(AngeloGioacchino Del Regno)"
* tag 'pm-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: mediatek: Handle sram regulator probe deferral
Linus Torvalds [Sat, 16 Jul 2022 17:52:41 +0000 (10:52 -0700)]
Merge tag 'acpi-5.19-rc7' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix more fallout from recent changes of the ACPI CPPC handling on AMD
platforms (Mario Limonciello)"
* tag 'acpi-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: CPPC: Fix enabling CPPC on AMD systems with shared memory
Linus Torvalds [Sat, 16 Jul 2022 17:46:03 +0000 (10:46 -0700)]
Merge tag 'printk-for-5.19-rc7' of git://git./linux/kernel/git/printk/linux
Pull printk fix from Petr Mladek:
- Make pr_flush() fast when consoles are suspended.
* tag 'printk-for-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk: do not wait for consoles when suspended
Jason A. Donenfeld [Wed, 13 Jul 2022 15:11:15 +0000 (17:11 +0200)]
random: cap jitter samples per bit to factor of HZ
Currently the jitter mechanism will require two timer ticks per
iteration, and it requires N iterations per bit. This N is determined
with a small measurement, and if it's too big, it won't waste time with
jitter entropy because it'd take too long or not have sufficient entropy
anyway.
With the current max N of 32, there are large timeouts on systems with a
small CONFIG_HZ. Rather than set that maximum to 32, instead choose a
factor of CONFIG_HZ. In this case, 1/30 seems to yield sane values for
different configurations of CONFIG_HZ.
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Fixes:
78c768e619fb ("random: vary jitter iterations based on cycle counter speed")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thadeu Lima de Souza Cascardo [Fri, 15 Jul 2022 19:45:50 +0000 (16:45 -0300)]
efi/x86: use naked RET on mixed mode call wrapper
When running with return thunks enabled under 32-bit EFI, the system
crashes with:
kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
BUG: unable to handle page fault for address:
000000005bc02900
#PF: supervisor instruction fetch in kernel mode
#PF: error_code(0x0011) - permissions violation
PGD
18f7063 P4D
18f7063 PUD
18ff063 PMD
190e063 PTE
800000005bc02063
Oops: 0011 [#1] PREEMPT SMP PTI
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.19.0-rc6+ #166
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:0x5bc02900
Code: Unable to access opcode bytes at RIP 0x5bc028d6.
RSP: 0018:
ffffffffb3203e10 EFLAGS:
00010046
RAX:
0000000000000000 RBX:
0000000000000000 RCX:
0000000000000048
RDX:
000000000190dfac RSI:
0000000000001710 RDI:
000000007eae823b
RBP:
ffffffffb3203e70 R08:
0000000001970000 R09:
ffffffffb3203e28
R10:
747563657865206c R11:
6c6977203a696665 R12:
0000000000001710
R13:
0000000000000030 R14:
0000000001970000 R15:
0000000000000001
FS:
0000000000000000(0000) GS:
ffff8e013ca00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0:
0000000080050033
CR2:
000000005bc02900 CR3:
0000000001930000 CR4:
00000000000006f0
Call Trace:
? efi_set_virtual_address_map+0x9c/0x175
efi_enter_virtual_mode+0x4a6/0x53e
start_kernel+0x67c/0x71e
x86_64_start_reservations+0x24/0x2a
x86_64_start_kernel+0xe9/0xf4
secondary_startup_64_no_verify+0xe5/0xeb
That's because it cannot jump to the return thunk from the 32-bit code.
Using a naked RET and marking it as safe allows the system to proceed
booting.
Fixes:
aa3d480315ba ("x86: Use return-thunk in asm code")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: <stable@vger.kernel.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kim Phillips [Fri, 8 Jul 2022 21:21:28 +0000 (16:21 -0500)]
x86/bugs: Remove apostrophe typo
Remove a superfluous ' in the mitigation string.
Fixes:
e8ec1b6e08a2 ("x86/bugs: Enable STIBP for JMP2RET")
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Linus Torvalds [Fri, 15 Jul 2022 17:40:50 +0000 (10:40 -0700)]
Merge tag 'riscv-for-linus-5.19-rc7' of git://git./linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A fix to avoid printing a warning when modules do not exercise any
errata-dependent behavior and the SiFive errata are enabled.
- A fix to the Microchip PFSOC to attach the L2 cache to the CPU nodes.
* tag 'riscv-for-linus-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: don't warn for sifive erratas in modules
riscv: dts: microchip: hook up the mpfs' l2cache
Linus Torvalds [Fri, 15 Jul 2022 17:31:46 +0000 (10:31 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"RISC-V:
- Fix missing PAGE_PFN_MASK
- Fix SRCU deadlock caused by kvm_riscv_check_vcpu_requests()
x86:
- Fix for nested virtualization when TSC scaling is active
- Estimate the size of fastcc subroutines conservatively, avoiding
disastrous underestimation when return thunks are enabled
- Avoid possible use of uninitialized fields of 'struct
kvm_lapic_irq'
Generic:
- Mark as such the boolean values available from the statistics file
descriptors
- Clarify statistics documentation"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: emulate: do not adjust size of fastop and setcc subroutines
KVM: x86: Fully initialize 'struct kvm_lapic_irq' in kvm_pv_kick_cpu_op()
Documentation: kvm: clarify histogram units
kvm: stats: tell userspace which values are boolean
x86/kvm: fix FASTOP_SIZE when return thunks are enabled
KVM: nVMX: Always enable TSC scaling for L2 when it was enabled for L1
RISC-V: KVM: Fix SRCU deadlock caused by kvm_riscv_check_vcpu_requests()
riscv: Fix missing PAGE_PFN_MASK
Linus Torvalds [Fri, 15 Jul 2022 17:27:28 +0000 (10:27 -0700)]
Merge tag 'ceph-for-5.19-rc7' of https://github.com/ceph/ceph-client
Pull ceph fix from Ilya Dryomov:
"A folio locking fixup that Xiubo and David cooperated on, marked for
stable. Most of it is in netfs but I picked it up into ceph tree on
agreement with David"
* tag 'ceph-for-5.19-rc7' of https://github.com/ceph/ceph-client:
netfs: do not unlock and put the folio twice
Linus Torvalds [Fri, 15 Jul 2022 17:23:43 +0000 (10:23 -0700)]
Merge tag 'spi-fix-v5.19-rc4' of git://git./linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes, none especially remarkable, plus a
MAINTAINERS file update due to the previous maintainer for the NXP
FSPI driver having left the company"
* tag 'spi-fix-v5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: cadence-quadspi: Remove spi_master_put() in probe failure path
MAINTAINERS: change the NXP FSPI driver maintainer.
spi: amd: Limit max transfer and message size
spi: aspeed: Fix division by zero
spi: aspeed: Add dev_dbg() to dump the spi-mem direct mapping descriptor
Linus Torvalds [Fri, 15 Jul 2022 17:16:44 +0000 (10:16 -0700)]
Merge tag 'soc-fixes-5.19-3' of git://git./linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Most of the contents are bugfixes for the devicetree files:
- A Qualcomm MSM8974 pin controller regression, caused by a cleanup
patch that gets partially reverted here.
- Missing properties for Broadcom BCM49xx to fix timer detection and
SMP boot.
- Fix touchscreen pinctrl for imx6ull-colibri board
- Multiple fixes for Rockchip rk3399 based machines including the vdu
clock-rate fix, otg port fix on Quartz64-A and ethernet on
Quartz64-B
- Fixes for misspelled DT contents causing minor problems on
imx6qdl-ts7970m, orangepi-zero, sama5d2, kontron-kswitch-d10, and
ls1028a
And a couple of changes elsewhere:
- Fix binding for Allwinner D1 display pipeline
- Trivial code fixes to the TEE and reset controller driver
subsystems and the rockchip platform code.
- Multiple updates to the MAINTAINERS files, marking the Palm Treo
support as orphaned, and fixing some entries for added or changed
file names"
* tag 'soc-fixes-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (21 commits)
arm64: dts: broadcom: bcm4908: Fix cpu node for smp boot
arm64: dts: broadcom: bcm4908: Fix timer node for BCM4906 SoC
ARM: dts: sunxi: Fix SPI NOR campatible on Orange Pi Zero
ARM: dts: at91: sama5d2: Fix typo in i2s1 node
tee: tee_get_drvdata(): fix description of return value
optee: Remove duplicate 'of' in two places.
ARM: dts: kswitch-d10: use open drain mode for coma-mode pins
ARM: dts: colibri-imx6ull: fix snvs pinmux group
optee: smc_abi.c: fix wrong pointer passed to IS_ERR/PTR_ERR()
MAINTAINERS: add polarfire rng, pci and clock drivers
MAINTAINERS: mark ARM/PALM TREO SUPPORT orphan
ARM: dts: imx6qdl-ts7970: Fix ngpio typo and count
arm64: dts: ls1028a: Update SFP node to include clock
dt-bindings: display: sun4i: Fix D1 pipeline count
ARM: dts: qcom: msm8974: re-add missing pinctrl
reset: Fix devm bulk optional exclusive control getter
MAINTAINERS: rectify entry for SYNOPSYS AXS10x RESET CONTROLLER DRIVER
ARM: rockchip: Add missing of_node_put() in rockchip_suspend_init()
arm64: dts: rockchip: Assign RK3399 VDU clock rate
arm64: dts: rockchip: Fix Quartz64-A dwc3 otg port behavior
...
David Sterba [Fri, 15 Jul 2022 11:59:45 +0000 (13:59 +0200)]
Revert "btrfs: turn delayed_nodes_tree into an XArray"
This reverts commit
253bf57555e451dec5a7f09dc95d380ce8b10e5b.
Revert the xarray conversion, there's a problem with potential
sleep-inside-spinlock [1] when calling xa_insert that triggers GFP_NOFS
allocation. The radix tree used the preloading mechanism to avoid
sleeping but this is not available in xarray.
Conversion from spin lock to mutex is possible but at time of rc6 is
riskier than a clean revert.
[1] https://lore.kernel.org/linux-btrfs/cover.
1657097693.git.fdmanana@suse.com/
Reported-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Fri, 15 Jul 2022 11:59:38 +0000 (13:59 +0200)]
Revert "btrfs: turn name_cache radix tree into XArray in send_ctx"
This reverts commit
4076942021fe14efecae33bf98566df6dd5ae6f7.
Revert the xarray conversion, there's a problem with potential
sleep-inside-spinlock [1] when calling xa_insert that triggers GFP_NOFS
allocation. The radix tree used the preloading mechanism to avoid
sleeping but this is not available in xarray.
Conversion from spin lock to mutex is possible but at time of rc6 is
riskier than a clean revert.
[1] https://lore.kernel.org/linux-btrfs/cover.
1657097693.git.fdmanana@suse.com/
Reported-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Fri, 15 Jul 2022 11:59:31 +0000 (13:59 +0200)]
Revert "btrfs: turn fs_info member buffer_radix into XArray"
This reverts commit
8ee922689d67b7cfa6acbe2aa1ee76ac72e6fc8a.
Revert the xarray conversion, there's a problem with potential
sleep-inside-spinlock [1] when calling xa_insert that triggers GFP_NOFS
allocation. The radix tree used the preloading mechanism to avoid
sleeping but this is not available in xarray.
Conversion from spin lock to mutex is possible but at time of rc6 is
riskier than a clean revert.
[1] https://lore.kernel.org/linux-btrfs/cover.
1657097693.git.fdmanana@suse.com/
Reported-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Fri, 15 Jul 2022 11:59:21 +0000 (13:59 +0200)]
Revert "btrfs: turn fs_roots_radix in btrfs_fs_info into an XArray"
This reverts commit
48b36a602a335c184505346b5b37077840660634.
Revert the xarray conversion, there's a problem with potential
sleep-inside-spinlock [1] when calling xa_insert that triggers GFP_NOFS
allocation. The radix tree used the preloading mechanism to avoid
sleeping but this is not available in xarray.
Conversion from spin lock to mutex is possible but at time of rc6 is
riskier than a clean revert.
[1] https://lore.kernel.org/linux-btrfs/cover.
1657097693.git.fdmanana@suse.com/
Reported-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Linus Torvalds [Fri, 15 Jul 2022 17:12:22 +0000 (10:12 -0700)]
Merge tag 'platform-drivers-x86-v5.19-4' of git://git./linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"Highlights:
- Fix brightness key events getting reported twice on some Dells.
Regression caused by recent Panasonic hotkey fixes
- Fix poweroff no longer working on some devices regression caused
by recent poweroff handler rework
- Mark new (in 5.19) Intel IFS driver as broken, because of some
issues surrounding the userspace (sysfs) API which need to be
cleared up
- Some hardware-id / quirk additions"
* tag 'platform-drivers-x86-v5.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
ACPI: video: Fix acpi_video_handles_brightness_key_presses()
platform/x86: intel_atomisp2_led: Also turn off the always-on camera LED on the Asus T100TAF
platform/x86/intel/ifs: Mark as BROKEN
platform/x86: asus-wmi: Add key mappings
efi: Fix efi_power_off() not being run before acpi_power_off() when necessary
platform/x86: x86-android-tablets: Fix Lenovo Yoga Tablet 2 830/1050 poweroff again
platform/x86: gigabyte-wmi: add support for B660I AORUS PRO DDR4
platform/x86/amd/pmc: Add new platform support
platform/x86/amd/pmc: Add new acpi id for PMC controller
Linus Torvalds [Fri, 15 Jul 2022 17:00:49 +0000 (10:00 -0700)]
Merge tag 'for-linus-5.19a-rc7-tag' of git://git./linux/kernel/git/xen/tip
Pull xen fix from Juergen Gross:
"Fix for the Xen gntdev driver causing inappropriate WARN() messages"
* tag 'for-linus-5.19a-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/gntdev: Ignore failure to unmap INVALID_GRANT_HANDLE
Linus Torvalds [Fri, 15 Jul 2022 16:56:24 +0000 (09:56 -0700)]
Merge tag 'drm-fixes-2022-07-15' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"This is the regular fixes pull for this week. This has a bunch of
amdgpu fixes, major one reverts the buddy allocator until it can be
tested more, otherwise just small ones, then i915 has a bunch of
fixes.
The outstanding firmware regressions reported by phoronix will
hopefully be dealt with ASAP.
amdgpu:
- revert buddy allocator support for now
- DP MST blank screen fix for specific platforms
- MEC firmware check fix for GC 10.3.7
- Deep color fix for DCE
- Fix possible divide by 0
- Coverage blend mode fix
- Fix cursor only commit timestamps
i915:
- Selftest fix
- TTM fix sg_table construction
- Error return fixes
- Fix a performance regression related to waitboost
- Fix GT resets"
* tag 'drm-fixes-2022-07-15' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Ensure valid event timestamp for cursor-only commits
drm/amd/display: correct check of coverage blend mode
drm/amd/pm: Prevent divide by zero
drm/amd/display: Only use depth 36 bpp linebuffers on DCN display engines.
drm/amdkfd: correct the MEC atomic support firmware checking for GC 10.3.7
drm/amd/display: Ignore First MST Sideband Message Return Error
drm/i915/selftests: fix subtraction overflow bug
drm/i915/gem: Look for waitboosting across the whole object prior to individual waits
drm/i915/gt: Serialize TLB invalidates with GT resets
drm/i915/gt: Serialize GRDOM access between multiple engine resets
drm/i915/ttm: fix sg_table construction
drm/i915/selftests: fix a couple IS_ERR() vs NULL tests
drm/i915: Fix vm use-after-free in vma destruction
drm/i915/guc: ADL-N should use the same GuC FW as ADL-S
drm/i915: fix a possible refcount leak in intel_dp_add_mst_connector()
drm/i915/gvt: IS_ERR() vs NULL bug in intel_gvt_update_reg_whitelist()
Revert "drm/amdgpu: add drm buddy support to amdgpu"
Linus Torvalds [Fri, 15 Jul 2022 16:52:35 +0000 (09:52 -0700)]
Merge tag 'sysctl-fixes-5.19-rc7' of git://git./linux/kernel/git/mcgrof/linux
Pyll sysctl fix from Luis Chamberlain:
"Only one fix for sysctl"
* tag 'sysctl-fixes-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
mm: sysctl: fix missing numa_stat when !CONFIG_HUGETLB_PAGE
Petr Mladek [Fri, 15 Jul 2022 14:43:42 +0000 (16:43 +0200)]
Merge branch 'rework/kthreads' into for-linus
Rafael J. Wysocki [Fri, 15 Jul 2022 11:54:14 +0000 (13:54 +0200)]
Merge tag 'cpufreq-arm-fixes-5.19-rc7' of git://git./linux/kernel/git/vireshk/pm
Pull a cpufreq ARM fix for 5.19-rc7 from Viresh Kumar:
- mediatek: Handle sram regulator probe deferral
* tag 'cpufreq-arm-fixes-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: mediatek: Handle sram regulator probe deferral
Paolo Bonzini [Fri, 15 Jul 2022 11:34:55 +0000 (07:34 -0400)]
KVM: emulate: do not adjust size of fastop and setcc subroutines
Instead of doing complicated calculations to find the size of the subroutines
(which are even more complicated because they need to be stringified into
an asm statement), just hardcode to 16.
It is less dense for a few combinations of IBT/SLS/retbleed, but it has
the advantage of being really simple.
Cc: stable@vger.kernel.org # 5.15.x: 84e7051c0bc1: x86/kvm: fix FASTOP_SIZE when return thunks are enabled
Cc: stable@vger.kernel.org
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
John Ogness [Fri, 15 Jul 2022 06:10:42 +0000 (08:16 +0206)]
printk: do not wait for consoles when suspended
The console_stop() and console_start() functions call pr_flush().
When suspending, these functions are called by the serial subsystem
while the serial port is suspended. In this scenario, if there are
any pending messages, a call to pr_flush() will always result in a
timeout because the serial port cannot make forward progress. This
causes longer suspend and resume times.
Add a check in pr_flush() so that it will immediately timeout if
the consoles are suspended.
Fixes:
3b604ca81202 ("printk: add pr_flush()")
Reported-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Tested-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20220715061042.373640-2-john.ogness@linutronix.de
Tony Krowiak [Wed, 6 Jul 2022 21:43:29 +0000 (17:43 -0400)]
s390/ap: fix error handling in __verify_queue_reservations()
The AP bus's __verify_queue_reservations function increments the ref count
for the device driver passed in as a parameter, but fails to decrement it
before returning control to the caller. This will prevents any subsequent
removal of the module.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reported-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Fixes:
4f8206b88286 ("s390/ap: driver callback to indicate resource in use")
Link: https://lore.kernel.org/r/20220706222619.602094-1-akrowiak@linux.ibm.com
Cc: stable@vger.kernel.org
[agordeev@linux.ibm.com fixed description, added Fixes and Link]
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Dave Airlie [Fri, 15 Jul 2022 01:26:20 +0000 (11:26 +1000)]
Merge tag 'amd-drm-fixes-5.19-2022-07-13' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.19-2022-07-13:
amdgpu:
- DP MST blank screen fix for specific platforms
- MEC firmware check fix for GC 10.3.7
- Deep color fix for DCE
- Fix possible divide by 0
- Coverage blend mode fix
- Fix cursor only commit timestamps
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220713172920.6037-1-alexander.deucher@amd.com
Dave Airlie [Thu, 14 Jul 2022 23:27:05 +0000 (09:27 +1000)]
Merge tag 'drm-intel-fixes-2022-07-13' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Selftest fix (Andrzej)
- TTM fix sg_table construction (Matt Auld)
- Error return fixes (Dan)
- Fix a performance regression related to waitboost (Chris)
- Fix GT resets (Chris)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Ys87yMujcG2sJC1R@intel.com
Dave Airlie [Thu, 14 Jul 2022 23:26:00 +0000 (09:26 +1000)]
Merge tag 'drm-misc-fixes-2022-07-14' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Only a revert for amdgpu reverting the switch to the drm buddy
allocator.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220714071821.hsejxpsgkbbzlec2@houat
Nick Desaulniers [Thu, 14 Jul 2022 20:56:43 +0000 (13:56 -0700)]
ubsan: disable UBSAN_DIV_ZERO for clang
Building with UBSAN_DIV_ZERO with clang produces numerous fallthrough
warnings from objtool.
In the case of uncheck division, UBSAN_DIV_ZERO may introduce new
control flow to check for division by zero.
Because the result of the division is undefined, LLVM may optimize the
control flow such that after the call to __ubsan_handle_divrem_overflow
doesn't matter. If panic_on_warn was set,
__ubsan_handle_divrem_overflow would panic.
The problem is is that panic_on_warn is run time configurable. If it's
disabled, then we cannot guarantee that we will be able to recover
safely. Disable this config for clang until we can come up with a
solution in LLVM.
Link: https://github.com/ClangBuiltLinux/linux/issues/1657
Link: https://github.com/llvm/llvm-project/issues/56289
Link: https://lore.kernel.org/lkml/CAHk-=wj1qhf7y3VNACEexyp5EbkNpdcu_542k-xZpzmYLOjiCg@mail.gmail.com/
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 14 Jul 2022 22:35:24 +0000 (15:35 -0700)]
Revert "vf/remap: return the amount of bytes actually deduplicated"
This reverts commit
4a57a8400075bc5287c5c877702c68aeae2a033d.
Dave Chinner reports:
"As I suspected would occur, this change causes test failures. e.g
generic/517 in fstests fails with:
generic/517 1s ... - output mismatch [..]
-deduped 131172/131172 bytes at offset 65536
+deduped 131072/131172 bytes at offset 65536"
can you please revert this commit for the 5.19 series to give us more
time to investigate and consider the impact of the the API change on
userspace applications before we commit to changing the API"
That changed return value seems to reflect reality, but with the fstest
change, let's revert for now.
Requested-by: Dave Chinner <david@fromorbit.com>
Link: https://lore.kernel.org/all/20220714223238.GH3600936@dread.disaster.area/
Cc: Ansgar Lößer <ansgar.loesser@tu-darmstadt.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nathan Chancellor [Wed, 13 Jul 2022 15:24:37 +0000 (08:24 -0700)]
x86/speculation: Use DECLARE_PER_CPU for x86_spec_ctrl_current
Clang warns:
arch/x86/kernel/cpu/bugs.c:58:21: error: section attribute is specified on redeclared variable [-Werror,-Wsection]
DEFINE_PER_CPU(u64, x86_spec_ctrl_current);
^
arch/x86/include/asm/nospec-branch.h:283:12: note: previous declaration is here
extern u64 x86_spec_ctrl_current;
^
1 error generated.
The declaration should be using DECLARE_PER_CPU instead so all
attributes stay in sync.
Cc: stable@vger.kernel.org
Fixes:
fc02735b14ff ("KVM: VMX: Prevent guest RSB poisoning attacks with eIBRS")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Muchun Song [Thu, 9 Jun 2022 10:40:32 +0000 (18:40 +0800)]
mm: sysctl: fix missing numa_stat when !CONFIG_HUGETLB_PAGE
"numa_stat" should not be included in the scope of CONFIG_HUGETLB_PAGE, if
CONFIG_HUGETLB_PAGE is not configured even if CONFIG_NUMA is configured,
"numa_stat" is missed form /proc. Move it out of CONFIG_HUGETLB_PAGE to
fix it.
Fixes:
4518085e127d ("mm, sysctl: make NUMA stats configurable")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Cc: <stable@vger.kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Linus Torvalds [Thu, 14 Jul 2022 19:48:07 +0000 (12:48 -0700)]
Merge tag 'net-5.19-rc7' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, bpf and wireless.
Still no major regressions, the release continues to be calm. An
uptick of fixes this time around due to trivial data race fixes and
patches flowing down from subtrees.
There has been a few driver fixes (particularly a few fixes for false
positives due to
66e4c8d95008 which went into -next in May!) that make
me worry the wide testing is not exactly fully through.
So "calm" but not "let's just cut the final ASAP" vibes over here.
Current release - regressions:
- wifi: rtw88: fix write to const table of channel parameters
Current release - new code bugs:
- mac80211: add gfp_t arg to ieeee80211_obss_color_collision_notify
- mlx5:
- TC, allow offload from uplink to other PF's VF
- Lag, decouple FDB selection and shared FDB
- Lag, correct get the port select mode str
- bnxt_en: fix and simplify XDP transmit path
- r8152: fix accessing unset transport header
Previous releases - regressions:
- conntrack: fix crash due to confirmed bit load reordering (after
atomic -> refcount conversion)
- stmmac: dwc-qos: disable split header for Tegra194
Previous releases - always broken:
- mlx5e: ring the TX doorbell on DMA errors
- bpf: make sure mac_header was set before using it
- mac80211: do not wake queues on a vif that is being stopped
- mac80211: fix queue selection for mesh/OCB interfaces
- ip: fix dflt addr selection for connected nexthop
- seg6: fix skb checksums for SRH encapsulation/insertion
- xdp: fix spurious packet loss in generic XDP TX path
- bunch of sysctl data race fixes
- nf_log: incorrect offset to network header
Misc:
- bpf: add flags arg to bpf_dynptr_read and bpf_dynptr_write APIs"
* tag 'net-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
nfp: flower: configure tunnel neighbour on cmsg rx
net/tls: Check for errors in tls_device_init
MAINTAINERS: Add an additional maintainer to the AMD XGBE driver
xen/netback: avoid entering xenvif_rx_next_skb() with an empty rx queue
selftests/net: test nexthop without gw
ip: fix dflt addr selection for connected nexthop
net: atlantic: remove aq_nic_deinit() when resume
net: atlantic: remove deep parameter on suspend/resume functions
sfc: fix kernel panic when creating VF
seg6: bpf: fix skb checksum in bpf_push_seg6_encap()
seg6: fix skb checksum in SRv6 End.B6 and End.B6.Encaps behaviors
seg6: fix skb checksum evaluation in SRH encapsulation/insertion
sfc: fix use after free when disabling sriov
net: sunhme: output link status with a single print.
r8152: fix accessing unset transport header
net: stmmac: fix leaks in probe
net: ftgmac100: Hold reference returned by of_get_child_by_name()
nexthop: Fix data-races around nexthop_compat_mode.
ipv4: Fix data-races around sysctl_ip_dynaddr.
tcp: Fix a data-race around sysctl_tcp_ecn_fallback.
...
Hans de Goede [Wed, 13 Jul 2022 21:11:01 +0000 (23:11 +0200)]
ACPI: video: Fix acpi_video_handles_brightness_key_presses()
Commit
3a0cf7ab8df3 ("ACPI: video: Change how we determine if brightness
key-presses are handled") made acpi_video_handles_brightness_key_presses()
report false when none of the ACPI Video Devices support backlight control.
But it turns out that at least on a Dell Inspiron N4010 there is no ACPI
backlight control, yet brightness hotkeys are still reported through
the ACPI Video Bus; and since acpi_video_handles_brightness_key_presses()
now returns false, brightness keypresses are now reported twice.
To fix this rename the has_backlight flag to may_report_brightness_keys and
also set it the first time a brightness key press event is received.
Depending on the delivery of the other ACPI (WMI) event vs the ACPI Video
Bus event this means that the first brightness key press might still get
reported twice, but all further keypresses will be filtered as before.
Note that this relies on other drivers reporting brightness key events
calling acpi_video_handles_brightness_key_presses() when delivering
the events (rather then once during driver probe). This is already
required and documented in include/acpi/video.h:
/*
* Note: The value returned by acpi_video_handles_brightness_key_presses()
* may change over time and should not be cached.
*/
Fixes:
3a0cf7ab8df3 ("ACPI: video: Change how we determine if brightness key-presses are handled")
Link: https://lore.kernel.org/regressions/CALF=6jEe5G8+r1Wo0vvz4GjNQQhdkLT5p8uCHn6ZXhg4nsOWow@mail.gmail.com/
Reported-and-tested-by: Ben Greening <bgreening@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20220713211101.85547-2-hdegoede@redhat.com
Linus Torvalds [Thu, 14 Jul 2022 19:35:15 +0000 (12:35 -0700)]
Merge tag '5.19-rc6-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Three smb3 client fixes:
- two multichannel fixes: fix a potential deadlock freeing a channel,
and fix a race condition on failed creation of a new channel
- mount failure fix: work around a server bug in some common older
Samba servers by avoiding padding at the end of the negotiate
protocol request"
* tag '5.19-rc6-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb3: workaround negprot bug in some Samba servers
cifs: remove unnecessary locking of chan_lock while freeing session
cifs: fix race condition with delayed threads
Linus Torvalds [Thu, 14 Jul 2022 19:29:43 +0000 (12:29 -0700)]
Merge tag 'nfsd-5.19-3' of git://git./linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
"Notable regression fixes:
- Enable SETATTR(time_create) to fix regression with Mac OS clients
- Fix a lockd crasher and broken NLM UNLCK behavior"
* tag 'nfsd-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
lockd: fix nlm_close_files
lockd: set fl_owner when unlocking files
NFSD: Decode NFSv4 birth time attribute
Linus Torvalds [Thu, 14 Jul 2022 19:15:42 +0000 (12:15 -0700)]
Merge tag 'integrity-v5.19-fix' of git://git./linux/kernel/git/zohar/linux-integrity
Pull integrity fixes from Mimi Zohar:
"Here are a number of fixes for recently found bugs.
Only 'ima: fix violation measurement list record' was introduced in
the current release. The rest address existing bugs"
* tag 'integrity-v5.19-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
ima: Fix potential memory leak in ima_init_crypto()
ima: force signature verification when CONFIG_KEXEC_SIG is configured
ima: Fix a potential integer overflow in ima_appraise_measurement
ima: fix violation measurement list record
Revert "evm: Fix memleak in init_desc"
Linus Torvalds [Thu, 14 Jul 2022 19:08:59 +0000 (12:08 -0700)]
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- quieten the spectre-bhb prints
- mark flattened device tree sections as shareable
- remove some obsolete CPU domain code and help text
- fix thumb unaligned access abort emulation
- fix amba_device_add() refcount underflow
- fix literal placement
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9208/1: entry: add .ltorg directive to keep literals in range
ARM: 9207/1: amba: fix refcount underflow if amba_device_add() fails
ARM: 9214/1: alignment: advance IT state after emulating Thumb instruction
ARM: 9213/1: Print message about disabled Spectre workarounds only once
ARM: 9212/1: domain: Modify Kconfig help text
ARM: 9211/1: domain: drop modify_domain()
ARM: 9210/1: Mark the FDT_FIXED sections as shareable
ARM: 9209/1: Spectre-BHB: avoid pr_info() every time a CPU comes out of idle
Guenter Roeck [Thu, 14 Jul 2022 18:46:00 +0000 (11:46 -0700)]
um: Replace to_phys() and to_virt() with less generic function names
The UML function names to_virt() and to_phys() are exposed by UML
headers, and are very generic and may be defined by drivers. As it
turns out, commit
9409c9b6709e ("pmem: refactor pmem_clear_poison()")
did exactly that.
This results in build errors such as the following when trying to build
um:allmodconfig:
drivers/nvdimm/pmem.c: In function ‘pmem_dax_zero_page_range’:
./arch/um/include/asm/page.h:105:20: error: too few arguments to function ‘to_phys’
105 | #define __pa(virt) to_phys((void *) (unsigned long) (virt))
| ^~~~~~~
Use less generic function names for the um specific to_phys() and
to_virt() functions to fix the problem and to avoid similar problems in
the future.
Fixes:
9409c9b6709e ("pmem: refactor pmem_clear_poison()")
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 14 Jul 2022 18:34:16 +0000 (11:34 -0700)]
Merge tag 'sound-5.19-rc7' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Hopefully the last one for 5.19. This became bigger than wished, but
all changes are pretty device-specific small fixes, which look less
worrisome.
The majority of changes are about various ASoC fixes, while the usual
HD-audio quirks are included as well"
* tag 'sound-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (28 commits)
ALSA: hda/realtek - Enable the headset-mic on a Xiaomi's laptop
ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc221
ALSA: hda/realtek: fix mute/micmute LEDs for HP machines
ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc671
ALSA: hda - Add fixup for Dell Latitidue E5430
ALSA: hda/conexant: Apply quirk for another HP ProDesk 600 G3 model
ALSA: hda/realtek: Fix headset mic for Acer SF313-51
ASoC: Intel: Skylake: Correct the handling of fmt_config flexible array
ASoC: Intel: Skylake: Correct the ssp rate discovery in skl_get_ssp_clks()
ASoC: rt5640: Fix the wrong state of JD1 and JD2
ASoC: Intel: sof_rt5682: fix out-of-bounds array access
ASoC: qdsp6: fix potential memory leak in q6apm_get_audioreach_graph()
ASoC: tas2764: Fix amp gain register offset & default
ASoC: tas2764: Correct playback volume range
ASoC: tas2764: Fix and extend FSYNC polarity handling
ASoC: tas2764: Add post reset delays
ASoC: dt-bindings: Fix description for msm8916
ASoC: doc: Capitalize RESET line name
ASoC: arizona: Update arizona_aif_cfg_changed to use RX_BCLK_RATE
ASoC: cs47l92: Fix event generation for OUT1 demux
...
Tianyu Yuan [Thu, 14 Jul 2022 08:19:15 +0000 (10:19 +0200)]
nfp: flower: configure tunnel neighbour on cmsg rx
nfp_tun_write_neigh() function will configure a tunnel neighbour when
calling nfp_tun_neigh_event_handler() or nfp_flower_cmsg_process_one_rx()
(with no tunnel neighbour type) from firmware.
When configuring IP on physical port as a tunnel endpoint, no operation
will be performed after receiving the cmsg mentioned above.
Therefore, add a progress to configure tunnel neighbour in this case.
v2: Correct format of fixes tag.
Fixes:
f1df7956c11f ("nfp: flower: rework tunnel neighbour configuration")
Signed-off-by: Tianyu Yuan <tianyu.yuan@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220714081915.148378-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tariq Toukan [Thu, 14 Jul 2022 07:07:54 +0000 (10:07 +0300)]
net/tls: Check for errors in tls_device_init
Add missing error checks in tls_device_init.
Fixes:
e8f69799810c ("net/tls: Add generic NIC offload infrastructure")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220714070754.1428-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tom Lendacky [Wed, 13 Jul 2022 22:31:41 +0000 (17:31 -0500)]
MAINTAINERS: Add an additional maintainer to the AMD XGBE driver
Add Shyam Sundar S K as an additional maintainer to support the AMD XGBE
network device driver.
Cc: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/db367f24089c2bbbcd1cec8e21af49922017a110.1657751501.git.thomas.lendacky@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Juergen Gross [Wed, 13 Jul 2022 13:53:22 +0000 (15:53 +0200)]
xen/netback: avoid entering xenvif_rx_next_skb() with an empty rx queue
xenvif_rx_next_skb() is expecting the rx queue not being empty, but
in case the loop in xenvif_rx_action() is doing multiple iterations,
the availability of another skb in the rx queue is not being checked.
This can lead to crashes:
[40072.537261] BUG: unable to handle kernel NULL pointer dereference at
0000000000000080
[40072.537407] IP: xenvif_rx_skb+0x23/0x590 [xen_netback]
[40072.537534] PGD 0 P4D 0
[40072.537644] Oops: 0000 [#1] SMP NOPTI
[40072.537749] CPU: 0 PID: 12505 Comm: v1-c40247-q2-gu Not tainted 4.12.14-122.121-default #1 SLE12-SP5
[40072.537867] Hardware name: HP ProLiant DL580 Gen9/ProLiant DL580 Gen9, BIOS U17 11/23/2021
[40072.537999] task:
ffff880433b38100 task.stack:
ffffc90043d40000
[40072.538112] RIP: e030:xenvif_rx_skb+0x23/0x590 [xen_netback]
[40072.538217] RSP: e02b:
ffffc90043d43de0 EFLAGS:
00010246
[40072.538319] RAX:
0000000000000000 RBX:
ffffc90043cd7cd0 RCX:
00000000000000f7
[40072.538430] RDX:
0000000000000000 RSI:
0000000000000006 RDI:
ffffc90043d43df8
[40072.538531] RBP:
000000000000003f R08:
000077ff80000000 R09:
0000000000000008
[40072.538644] R10:
0000000000007ff0 R11:
00000000000008f6 R12:
ffffc90043ce2708
[40072.538745] R13:
0000000000000000 R14:
ffffc90043d43ed0 R15:
ffff88043ea748c0
[40072.538861] FS:
0000000000000000(0000) GS:
ffff880484600000(0000) knlGS:
0000000000000000
[40072.538988] CS: e033 DS: 0000 ES: 0000 CR0:
0000000080050033
[40072.539088] CR2:
0000000000000080 CR3:
0000000407ac8000 CR4:
0000000000040660
[40072.539211] Call Trace:
[40072.539319] xenvif_rx_action+0x71/0x90 [xen_netback]
[40072.539429] xenvif_kthread_guest_rx+0x14a/0x29c [xen_netback]
Fix that by stopping the loop in case the rx queue becomes empty.
Cc: stable@vger.kernel.org
Fixes:
98f6d57ced73 ("xen-netback: process guest rx packets in batches")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Link: https://lore.kernel.org/r/20220713135322.19616-1-jgross@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Wed, 13 Jul 2022 19:36:50 +0000 (12:36 -0700)]
amdgpu: disable powerpc support for the newer display engine
The DRM_AMD_DC_DCN display engine support (Raven, Navi, and newer) has
not been building cleanly on powerpc and causes link errors due to
mixing hard- and soft-float object files:
powerpc64-linux-ld: drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.o uses hard float, drivers/gpu/drm/amd/amdgpu/../display/dc/dcn31/dcn31_resource.o uses soft float
powerpc64-linux-ld: failed to merge target specific data of file drivers/gpu/drm/amd/amdgpu/../display/dc/dcn31/dcn31_resource.o
[..]
and while patches are floating around, it's not exactly obvious what is
going on.
The problem bisects to commit
41b7a347bf14 ("powerpc: Book3S 64-bit
outline-only KASAN support") but that is probably more about changing
config variables than the fundamental cause.
Despite the bisection result, a more directly related commit seems to be
26f4712aedbd ("drm/amd/display: move FPU related code from dcn31 to
dml/dcn31 folder"). It's probably a combination of the two.
This has been going on since the merge window, without any final word.
So instead of blindly applying patches that may or may not be the right
thing, let's disable this for now.
As Michael Ellerman says:
"IIUIC this code was never enabled on ppc before, so disabling it seems
like a reasonable fix to get the build clean"
and once we have more actual feedback (and find any potential users) we
can always re-enable it with the patch that fixes the issues and
back-port as necessary.
Fixes:
41b7a347bf14 ("powerpc: Book3S 64-bit outline-only KASAN support")
Fixes:
26f4712aedbd ("drm/amd/display: move FPU related code from dcn31 to dml/dcn31 folder")
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/all/20220606153910.GA1773067@roeck-us.net/
Link: https://lore.kernel.org/all/20220618232737.2036722-1-linux@roeck-us.net/
Link: https://lore.kernel.org/all/20220713050724.GA2471738@roeck-us.net/
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Muchun Song [Wed, 13 Jul 2022 14:02:26 +0000 (22:02 +0800)]
block: fix missing blkcg_bio_issue_init
The commit
513616843d73 ("block: remove superfluous calls to
blkcg_bio_issue_init") has removed blkcg_bio_issue_init from
__bio_clone since submit_bio will override ->bi_issue.
However, __blk_queue_split is called after blkcg_bio_issue_init
(see blk_mq_submit_bio) in submit_bio. In this case, the
->bi_issue is 0. Fix it.
Fixes:
513616843d73 ("block: remove superfluous calls to blkcg_bio_issue_init")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Link: https://lore.kernel.org/r/20220713140226.68135-1-songmuchun@bytedance.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Thu, 14 Jul 2022 16:29:56 +0000 (10:29 -0600)]
Merge tag 'nvme-5.19-2022-07-14' of git://git.infradead.org/nvme into block-5.19
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 5.19
- fix a block device naming collision (Israel Rukshin)
- fix freeze accounting for PCI error handling (Keith Busch)"
* tag 'nvme-5.19-2022-07-14' of git://git.infradead.org/nvme:
nvme: fix block device naming collision
nvme-pci: fix freeze accounting for error handling
Vitaly Kuznetsov [Fri, 8 Jul 2022 12:51:47 +0000 (14:51 +0200)]
KVM: x86: Fully initialize 'struct kvm_lapic_irq' in kvm_pv_kick_cpu_op()
'vector' and 'trig_mode' fields of 'struct kvm_lapic_irq' are left
uninitialized in kvm_pv_kick_cpu_op(). While these fields are normally
not needed for APIC_DM_REMRD, they're still referenced by
__apic_accept_irq() for trace_kvm_apic_accept_irq(). Fully initialize
the structure to avoid consuming random stack memory.
Fixes:
a183b638b61c ("KVM: x86: make apic_accept_irq tracepoint more generic")
Reported-by: syzbot+d6caa905917d353f0d07@syzkaller.appspotmail.com
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <
20220708125147.593975-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Israel Rukshin [Thu, 14 Jul 2022 12:42:10 +0000 (12:42 +0000)]
nvme: fix block device naming collision
The issue exists when multipath is enabled and the namespace is
shared, but all the other controller checks at nvme_is_unique_nsid()
are false. The reason for this issue is that nvme_is_unique_nsid()
returns false when is called from nvme_mpath_alloc_disk() due to an
uninitialized value of head->shared. The patch fixes it by setting
head->shared before nvme_mpath_alloc_disk() is called.
Fixes:
5974ea7ce0f9 ("nvme: allow duplicate NSIDs for private namespaces")
Signed-off-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Keith Busch [Tue, 12 Jul 2022 15:16:32 +0000 (08:16 -0700)]
nvme-pci: fix freeze accounting for error handling
A reset on a live device experiencing a link error still needs to have
the queue freeze state started for the subsequent reinitialization. Skip
only the register read if the device is not present instead of bypassing
the freeze checks.
Fixes:
b98235d3a471e ("nvme-pci: harden drive presence detect in nvme_dev_disable()")
Reported-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Tested-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Greg Kroah-Hartman [Thu, 14 Jul 2022 14:22:12 +0000 (16:22 +0200)]
Merge tag 'usb-serial-5.19-rc7' of https://git./linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.19-rc7
Here are a couple of new device ids for ftdi_sio.
Everything has been in linux-next with no reported issues.
* tag 'usb-serial-5.19-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add Belimo device ids
Greg Kroah-Hartman [Thu, 14 Jul 2022 14:18:22 +0000 (16:18 +0200)]
Merge tag 'v5.19-rc6' into usb-linus
The usb-serial fixes are based on this branch, so merge it in here to
prevent merge confusion when merging in that tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paolo Bonzini [Thu, 14 Jul 2022 14:04:12 +0000 (10:04 -0400)]
Merge commit 'kvm-vmx-nested-tsc-fix' into kvm-master
Merge bugfix needed in both 5.19 (because it's bad) and 5.20 (because
it is a prerequisite to test new features).
Nicolas Dichtel [Wed, 13 Jul 2022 11:48:53 +0000 (13:48 +0200)]
selftests/net: test nexthop without gw
This test implement the scenario described in the commit
"ip: fix dflt addr selection for connected nexthop".
The test configures a nexthop object with an output device only (no gateway
address) and a route that uses this nexthop. The goal is to check if the
kernel selects a valid source address.
Link: https://lore.kernel.org/netdev/20220712095545.10947-1-nicolas.dichtel@6wind.com/
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20220713114853.29406-2-nicolas.dichtel@6wind.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Nicolas Dichtel [Wed, 13 Jul 2022 11:48:52 +0000 (13:48 +0200)]
ip: fix dflt addr selection for connected nexthop
When a nexthop is added, without a gw address, the default scope was set
to 'host'. Thus, when a source address is selected, 127.0.0.1 may be chosen
but rejected when the route is used.
When using a route without a nexthop id, the scope can be configured in the
route, thus the problem doesn't exist.
To explain more deeply: when a user creates a nexthop, it cannot specify
the scope. To create it, the function nh_create_ipv4() calls fib_check_nh()
with scope set to 0. fib_check_nh() calls fib_check_nh_nongw() wich was
setting scope to 'host'. Then, nh_create_ipv4() calls
fib_info_update_nhc_saddr() with scope set to 'host'. The src addr is
chosen before the route is inserted.
When a 'standard' route (ie without a reference to a nexthop) is added,
fib_create_info() calls fib_info_update_nhc_saddr() with the scope set by
the user. iproute2 set the scope to 'link' by default.
Here is a way to reproduce the problem:
ip netns add foo
ip -n foo link set lo up
ip netns add bar
ip -n bar link set lo up
sleep 1
ip -n foo link add name eth0 type dummy
ip -n foo link set eth0 up
ip -n foo address add 192.168.0.1/24 dev eth0
ip -n foo link add name veth0 type veth peer name veth1 netns bar
ip -n foo link set veth0 up
ip -n bar link set veth1 up
ip -n bar address add 192.168.1.1/32 dev veth1
ip -n bar route add default dev veth1
ip -n foo nexthop add id 1 dev veth0
ip -n foo route add 192.168.1.1 nhid 1
Try to get/use the route:
> $ ip -n foo route get 192.168.1.1
> RTNETLINK answers: Invalid argument
> $ ip netns exec foo ping -c1 192.168.1.1
> ping: connect: Invalid argument
Try without nexthop group (iproute2 sets scope to 'link' by dflt):
ip -n foo route del 192.168.1.1
ip -n foo route add 192.168.1.1 dev veth0
Try to get/use the route:
> $ ip -n foo route get 192.168.1.1
> 192.168.1.1 dev veth0 src 192.168.0.1 uid 0
> cache
> $ ip netns exec foo ping -c1 192.168.1.1
> PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
> 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.039 ms
>
> --- 192.168.1.1 ping statistics ---
> 1 packets transmitted, 1 received, 0% packet loss, time 0ms
> rtt min/avg/max/mdev = 0.039/0.039/0.039/0.000 ms
CC: stable@vger.kernel.org
Fixes:
597cfe4fc339 ("nexthop: Add support for IPv4 nexthops")
Reported-by: Edwin Brossette <edwin.brossette@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20220713114853.29406-1-nicolas.dichtel@6wind.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Vaishnav Achath [Wed, 1 Jun 2022 07:16:11 +0000 (12:46 +0530)]
spi: cadence-quadspi: Remove spi_master_put() in probe failure path
Currently the spi_master is allocated by devm_spi_alloc_master()
and devres core manages the deallocation, but in probe failure
path spi_master_put() is being handled manually which causes
"refcount underflow use-after-free" warning when probe failure happens
after allocating spi_master.
Trimmed backtrace during failure:
refcount_t: underflow; use-after-free.
pc : refcount_warn_saturate+0xf4/0x144
Call trace:
refcount_warn_saturate
kobject_put
put_device
devm_spi_release_controller
devres_release_all
This commit makes relevant changes to remove spi_master_put() from probe
failure path.
Fixes:
606e5d408184 ("spi: cadence-quadspi: Handle spi_unregister_master() in remove()")
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20220601071611.11853-1-vaishnav.a@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Ard Biesheuvel [Tue, 31 May 2022 08:49:24 +0000 (09:49 +0100)]
ARM: 9208/1: entry: add .ltorg directive to keep literals in range
LKP reports a build issue on Clang, related to a literal load of
__current issued through the ldr_va macro. This turns out to be due to
the fact that group relocations are disabled when CONFIG_COMPILE_TEST=y,
which means that the ldr_va macro resolves to a pair of LDR
instructions, the first one being a literal load issued too far from its
literal pool.
Due to the introduction of a couple of new uses of this macro in commit
508074607c7b95b2 ("ARM: 9195/1: entry: avoid explicit literal loads"),
the literal pools end up getting rearranged in a way that causes the
literal for __current to go out of range. Let's fix this up by putting a
.ltorg directive in a suitable place in the code.
Link: https://lore.kernel.org/all/202205290805.1vZLAr36-lkp@intel.com/
Fixes:
508074607c7b95b2 ("ARM: 9195/1: entry: avoid explicit literal loads")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Wang Kefeng [Tue, 24 May 2022 08:03:46 +0000 (09:03 +0100)]
ARM: 9207/1: amba: fix refcount underflow if amba_device_add() fails
"ARM: 9192/1: amba: fix memory leak in amba_device_try_add()" leads
to a refcount underflow if amba_device_add() fails, which called by
of_amba_device_create(), the of_amba_device_create() already exists
the error handling, so amba_put_device() only need to be added into
amba_deferred_retry().
Fixes:
7719a68b2fa4 ("ARM: 9192/1: amba: fix memory leak in amba_device_try_add()")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Paolo Bonzini [Thu, 14 Jul 2022 11:29:57 +0000 (07:29 -0400)]
Documentation: kvm: clarify histogram units
In the case of histogram statistics, the values are always sample
counts; the unit instead applies to the bucket range. For example,
halt_poll_success_hist is a nanosecond statistic because the buckets are
for 0ns, 1ns, 2-3ns, 4-7ns etc. There isn't really any other sensible
interpretation, but clarify this anyway in the Documentation.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Thu, 14 Jul 2022 11:27:31 +0000 (07:27 -0400)]
kvm: stats: tell userspace which values are boolean
Some of the statistics values exported by KVM are always only 0 or 1.
It can be useful to export this fact to userspace so that it can track
them specially (for example by polling the value every now and then to
compute a % of time spent in a specific state).
Therefore, add "boolean value" as a new "unit". While it is not exactly
a unit, it walks and quacks like one. In particular, using the type
would be wrong because boolean values could be instantaneous or peak
values (e.g. "is the rmap allocated?") or even two-bucket histograms
(e.g. "number of posted vs. non-posted interrupt injections").
Suggested-by: Amneesh Singh <natto@weirdnatto.in>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Thadeu Lima de Souza Cascardo [Wed, 13 Jul 2022 17:12:41 +0000 (14:12 -0300)]
x86/kvm: fix FASTOP_SIZE when return thunks are enabled
The return thunk call makes the fastop functions larger, just like IBT
does. Consider a 16-byte FASTOP_SIZE when CONFIG_RETHUNK is enabled.
Otherwise, functions will be incorrectly aligned and when computing their
position for differently sized operators, they will executed in the middle
or end of a function, which may as well be an int3, leading to a crash
like:
[ 36.091116] int3: 0000 [#1] SMP NOPTI
[ 36.091119] CPU: 3 PID: 1371 Comm: qemu-system-x86 Not tainted 5.15.0-41-generic #44
[ 36.091120] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1 04/01/2014
[ 36.091121] RIP: 0010:xaddw_ax_dx+0x9/0x10 [kvm]
[ 36.091185] Code: 00 0f bb d0 c3 cc cc cc cc 48 0f bb d0 c3 cc cc cc cc 0f 1f 80 00 00 00 00 0f c0 d0 c3 cc cc cc cc 66 0f c1 d0 c3 cc cc cc cc <0f> 1f 80 00 00 00 00 0f c1 d0 c3 cc cc cc cc 48 0f c1 d0 c3 cc cc
[ 36.091186] RSP: 0018:
ffffb1f541143c98 EFLAGS:
00000202
[ 36.091188] RAX:
0000000089abcdef RBX:
0000000000000001 RCX:
0000000000000000
[ 36.091188] RDX:
0000000076543210 RSI:
ffffffffc073c6d0 RDI:
0000000000000200
[ 36.091189] RBP:
ffffb1f541143ca0 R08:
ffff9f1803350a70 R09:
0000000000000002
[ 36.091190] R10:
ffff9f1803350a70 R11:
0000000000000000 R12:
ffff9f1803350a70
[ 36.091190] R13:
ffffffffc077fee0 R14:
0000000000000000 R15:
0000000000000000
[ 36.091191] FS:
00007efdfce8d640(0000) GS:
ffff9f187dd80000(0000) knlGS:
0000000000000000
[ 36.091192] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 36.091192] CR2:
0000000000000000 CR3:
0000000009b62002 CR4:
0000000000772ee0
[ 36.091195] PKRU:
55555554
[ 36.091195] Call Trace:
[ 36.091197] <TASK>
[ 36.091198] ? fastop+0x5a/0xa0 [kvm]
[ 36.091222] x86_emulate_insn+0x7b8/0xe90 [kvm]
[ 36.091244] x86_emulate_instruction+0x2f4/0x630 [kvm]
[ 36.091263] ? kvm_arch_vcpu_load+0x7c/0x230 [kvm]
[ 36.091283] ? vmx_prepare_switch_to_host+0xf7/0x190 [kvm_intel]
[ 36.091290] complete_emulated_mmio+0x297/0x320 [kvm]
[ 36.091310] kvm_arch_vcpu_ioctl_run+0x32f/0x550 [kvm]
[ 36.091330] kvm_vcpu_ioctl+0x29e/0x6d0 [kvm]
[ 36.091344] ? kvm_vcpu_ioctl+0x120/0x6d0 [kvm]
[ 36.091357] ? __fget_files+0x86/0xc0
[ 36.091362] ? __fget_files+0x86/0xc0
[ 36.091363] __x64_sys_ioctl+0x92/0xd0
[ 36.091366] do_syscall_64+0x59/0xc0
[ 36.091369] ? syscall_exit_to_user_mode+0x27/0x50
[ 36.091370] ? do_syscall_64+0x69/0xc0
[ 36.091371] ? syscall_exit_to_user_mode+0x27/0x50
[ 36.091372] ? __x64_sys_writev+0x1c/0x30
[ 36.091374] ? do_syscall_64+0x69/0xc0
[ 36.091374] ? exit_to_user_mode_prepare+0x37/0xb0
[ 36.091378] ? syscall_exit_to_user_mode+0x27/0x50
[ 36.091379] ? do_syscall_64+0x69/0xc0
[ 36.091379] ? do_syscall_64+0x69/0xc0
[ 36.091380] ? do_syscall_64+0x69/0xc0
[ 36.091381] ? do_syscall_64+0x69/0xc0
[ 36.091381] entry_SYSCALL_64_after_hwframe+0x61/0xcb
[ 36.091384] RIP: 0033:0x7efdfe6d1aff
[ 36.091390] Code: 00 48 89 44 24 18 31 c0 48 8d 44 24 60 c7 04 24 10 00 00 00 48 89 44 24 08 48 8d 44 24 20 48 89 44 24 10 b8 10 00 00 00 0f 05 <41> 89 c0 3d 00 f0 ff ff 77 1f 48 8b 44 24 18 64 48 2b 04 25 28 00
[ 36.091391] RSP: 002b:
00007efdfce8c460 EFLAGS:
00000246 ORIG_RAX:
0000000000000010
[ 36.091393] RAX:
ffffffffffffffda RBX:
000000000000ae80 RCX:
00007efdfe6d1aff
[ 36.091393] RDX:
0000000000000000 RSI:
000000000000ae80 RDI:
000000000000000c
[ 36.091394] RBP:
0000558f1609e220 R08:
0000558f13fb8190 R09:
00000000ffffffff
[ 36.091394] R10:
0000558f16b5e950 R11:
0000000000000246 R12:
0000000000000000
[ 36.091394] R13:
0000000000000001 R14:
0000000000000000 R15:
0000000000000000
[ 36.091396] </TASK>
[ 36.091397] Modules linked in: isofs nls_iso8859_1 kvm_intel joydev kvm input_leds serio_raw sch_fq_codel dm_multipath scsi_dh_rdac scsi_dh_emc scsi_dh_alua ipmi_devintf ipmi_msghandler drm msr ip_tables x_tables autofs4 btrfs blake2b_generic zstd_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 multipath linear crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel virtio_net net_failover crypto_simd ahci xhci_pci cryptd psmouse virtio_blk libahci xhci_pci_renesas failover
[ 36.123271] ---[ end trace
db3c0ab5a48fabcc ]---
[ 36.123272] RIP: 0010:xaddw_ax_dx+0x9/0x10 [kvm]
[ 36.123319] Code: 00 0f bb d0 c3 cc cc cc cc 48 0f bb d0 c3 cc cc cc cc 0f 1f 80 00 00 00 00 0f c0 d0 c3 cc cc cc cc 66 0f c1 d0 c3 cc cc cc cc <0f> 1f 80 00 00 00 00 0f c1 d0 c3 cc cc cc cc 48 0f c1 d0 c3 cc cc
[ 36.123320] RSP: 0018:
ffffb1f541143c98 EFLAGS:
00000202
[ 36.123321] RAX:
0000000089abcdef RBX:
0000000000000001 RCX:
0000000000000000
[ 36.123321] RDX:
0000000076543210 RSI:
ffffffffc073c6d0 RDI:
0000000000000200
[ 36.123322] RBP:
ffffb1f541143ca0 R08:
ffff9f1803350a70 R09:
0000000000000002
[ 36.123322] R10:
ffff9f1803350a70 R11:
0000000000000000 R12:
ffff9f1803350a70
[ 36.123323] R13:
ffffffffc077fee0 R14:
0000000000000000 R15:
0000000000000000
[ 36.123323] FS:
00007efdfce8d640(0000) GS:
ffff9f187dd80000(0000) knlGS:
0000000000000000
[ 36.123324] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 36.123325] CR2:
0000000000000000 CR3:
0000000009b62002 CR4:
0000000000772ee0
[ 36.123327] PKRU:
55555554
[ 36.123328] Kernel panic - not syncing: Fatal exception in interrupt
[ 36.123410] Kernel Offset: 0x1400000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)
[ 36.135305] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---
Fixes:
aa3d480315ba ("x86: Use return-thunk in asm code")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Co-developed-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Message-Id: <
20220713171241.184026-1-cascardo@canonical.com>
Tested-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Vitaly Kuznetsov [Tue, 12 Jul 2022 13:50:09 +0000 (15:50 +0200)]
KVM: nVMX: Always enable TSC scaling for L2 when it was enabled for L1
Windows 10/11 guests with Hyper-V role (WSL2) enabled are observed to
hang upon boot or shortly after when a non-default TSC frequency was
set for L1. The issue is observed on a host where TSC scaling is
supported. The problem appears to be that Windows doesn't use TSC
frequency for its guests even when the feature is advertised and KVM
filters SECONDARY_EXEC_TSC_SCALING out when creating L2 controls from
L1's. This leads to L2 running with the default frequency (matching
host's) while L1 is running with an altered one.
Keep SECONDARY_EXEC_TSC_SCALING in secondary exec controls for L2 when
it was set for L1. TSC_MULTIPLIER is already correctly computed and
written by prepare_vmcs02().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <
20220712135009.952805-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Peter Zijlstra [Thu, 14 Jul 2022 10:20:19 +0000 (12:20 +0200)]
um: Add missing apply_returns()
Implement apply_returns() stub for UM, just like all the other patching
routines.
Fixes:
15e67227c49a ("x86: Undo return-thunk damage")
Reported-by: Randy Dunlap <rdunlap@infradead.org)
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/Ys%2Ft45l%2FgarIrD0u@worktop.programming.kicks-ass.net
Chia-Lin Kao (AceLan) [Wed, 13 Jul 2022 11:12:24 +0000 (19:12 +0800)]
net: atlantic: remove aq_nic_deinit() when resume
aq_nic_deinit() has been called while suspending, so we don't have to call
it again on resume.
Actually, call it again leads to another hang issue when resuming from
S3.
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992345] Call Trace:
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992346] <TASK>
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992348] aq_nic_deinit+0xb4/0xd0 [atlantic]
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992356] aq_pm_thaw+0x7f/0x100 [atlantic]
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992362] pci_pm_resume+0x5c/0x90
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992366] ? pci_pm_thaw+0x80/0x80
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992368] dpm_run_callback+0x4e/0x120
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992371] device_resume+0xad/0x200
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992373] async_resume+0x1e/0x40
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992374] async_run_entry_fn+0x33/0x120
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992377] process_one_work+0x220/0x3c0
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992380] worker_thread+0x4d/0x3f0
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992382] ? process_one_work+0x3c0/0x3c0
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992384] kthread+0x12a/0x150
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992386] ? set_kthread_struct+0x40/0x40
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992387] ret_from_fork+0x22/0x30
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992391] </TASK>
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992392] ---[ end trace
1ec8c79604ed5e0d ]---
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992394] PM: dpm_run_callback(): pci_pm_resume+0x0/0x90 returns -110
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992397] atlantic 0000:02:00.0: PM: failed to resume async: error -110
Fixes:
1809c30b6e5a ("net: atlantic: always deep reset on pm op, fixing up my null deref regression")
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Link: https://lore.kernel.org/r/20220713111224.1535938-2-acelan.kao@canonical.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Chia-Lin Kao (AceLan) [Wed, 13 Jul 2022 11:12:23 +0000 (19:12 +0800)]
net: atlantic: remove deep parameter on suspend/resume functions
Below commit claims that atlantic NIC requires to reset the device on pm
op, and had set the deep to true for all suspend/resume functions.
commit
1809c30b6e5a ("net: atlantic: always deep reset on pm op, fixing up my null deref regression")
So, we could remove deep parameter on suspend/resume functions without
any functional change.
Fixes:
1809c30b6e5a ("net: atlantic: always deep reset on pm op, fixing up my null deref regression")
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Link: https://lore.kernel.org/r/20220713111224.1535938-1-acelan.kao@canonical.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Íñigo Huguet [Wed, 13 Jul 2022 09:21:16 +0000 (11:21 +0200)]
sfc: fix kernel panic when creating VF
When creating VFs a kernel panic can happen when calling to
efx_ef10_try_update_nic_stats_vf.
When releasing a DMA coherent buffer, sometimes, I don't know in what
specific circumstances, it has to unmap memory with vunmap. It is
disallowed to do that in IRQ context or with BH disabled. Otherwise, we
hit this line in vunmap, causing the crash:
BUG_ON(in_interrupt());
This patch reenables BH to release the buffer.
Log messages when the bug is hit:
kernel BUG at mm/vmalloc.c:2727!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 6 PID: 1462 Comm: NetworkManager Kdump: loaded Tainted: G I --------- --- 5.14.0-119.el9.x86_64 #1
Hardware name: Dell Inc. PowerEdge R740/06WXJT, BIOS 2.8.2 08/27/2020
RIP: 0010:vunmap+0x2e/0x30
...skip...
Call Trace:
__iommu_dma_free+0x96/0x100
efx_nic_free_buffer+0x2b/0x40 [sfc]
efx_ef10_try_update_nic_stats_vf+0x14a/0x1c0 [sfc]
efx_ef10_update_stats_vf+0x18/0x40 [sfc]
efx_start_all+0x15e/0x1d0 [sfc]
efx_net_open+0x5a/0xe0 [sfc]
__dev_open+0xe7/0x1a0
__dev_change_flags+0x1d7/0x240
dev_change_flags+0x21/0x60
...skip...
Fixes:
d778819609a2 ("sfc: DMA the VF stats only when requested")
Reported-by: Ma Yuying <yuma@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20220713092116.21238-1-ihuguet@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paolo Bonzini [Thu, 14 Jul 2022 10:01:53 +0000 (06:01 -0400)]
Merge tag 'kvm-riscv-fixes-5.19-2' of https://github.com/kvm-riscv/linux into HEAD
KVM/riscv fixes for 5.19, take #2
- Fix missing PAGE_PFN_MASK
- Fix SRCU deadlock caused by kvm_riscv_check_vcpu_requests()
Paolo Abeni [Thu, 14 Jul 2022 08:15:15 +0000 (10:15 +0200)]
Merge branch 'seg6-fix-skb-checksum-for-srh-encapsulation-insertion'
Andrea Mayer says:
====================
seg6: fix skb checksum for SRH encapsulation/insertion
The Linux kernel supports Segment Routing Header (SRH)
encapsulation/insertion operations by providing the capability to: i)
encapsulate a packet in an outer IPv6 header with a specified SRH; ii)
insert a specified SRH directly after the IPv6 header of the packet.
Note that the insertion operation is also referred to as 'injection'.
The two operations are respectively supported by seg6_do_srh_encap() and
seg6_do_srh_inline(), which operate on the skb associated to the packet as
needed (e.g. adding the necessary headers and initializing them, while
taking care to recalculate the skb checksum).
seg6_do_srh_encap() and seg6_do_srh_inline() do not initialize the payload
length of the IPv6 header, which is carried out by the caller functions.
However, this approach causes the corruption of the skb checksum which
needs to be updated only after initialization of headers is completed
(thanks to Paolo Abeni for detecting this issue).
The patchset fixes the skb checksum corruption by moving the IPv6 header
payload length initialization from the callers of seg6_do_srh_encap() and
seg6_do_srh_inline() directly into these functions.
This patchset is organized as follows:
- patch 1/3, seg6: fix skb checksum evaluation in SRH
encapsulation/insertion;
(* SRH encapsulation/insertion available since v4.10)
- patch 2/3, seg6: fix skb checksum in SRv6 End.B6 and End.B6.Encaps
behaviors;
(* SRv6 End.B6 and End.B6.Encaps behaviors available since v4.14)
- patch 3/3, seg6: bpf: fix skb checksum in bpf_push_seg6_encap();
(* bpf IPv6 Segment Routing helpers available since v4.18)
====================
Link: https://lore.kernel.org/r/20220712175837.16267-1-andrea.mayer@uniroma2.it
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Andrea Mayer [Tue, 12 Jul 2022 17:58:37 +0000 (19:58 +0200)]
seg6: bpf: fix skb checksum in bpf_push_seg6_encap()
Both helper functions bpf_lwt_seg6_action() and bpf_lwt_push_encap() use
the bpf_push_seg6_encap() to encapsulate the packet in an IPv6 with Segment
Routing Header (SRH) or insert an SRH between the IPv6 header and the
payload.
To achieve this result, such helper functions rely on bpf_push_seg6_encap()
which, in turn, leverages seg6_do_srh_{encap,inline}() to perform the
required operation (i.e. encap/inline).
This patch removes the initialization of the IPv6 header payload length
from bpf_push_seg6_encap(), as it is now handled properly by
seg6_do_srh_{encap,inline}() to prevent corruption of the skb checksum.
Fixes:
fe94cc290f53 ("bpf: Add IPv6 Segment Routing helpers")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Andrea Mayer [Tue, 12 Jul 2022 17:58:36 +0000 (19:58 +0200)]
seg6: fix skb checksum in SRv6 End.B6 and End.B6.Encaps behaviors
The SRv6 End.B6 and End.B6.Encaps behaviors rely on functions
seg6_do_srh_{encap,inline}() to, respectively: i) encapsulate the
packet within an outer IPv6 header with the specified Segment Routing
Header (SRH); ii) insert the specified SRH directly after the IPv6
header of the packet.
This patch removes the initialization of the IPv6 header payload length
from the input_action_end_b6{_encap}() functions, as it is now handled
properly by seg6_do_srh_{encap,inline}() to avoid corruption of the skb
checksum.
Fixes:
140f04c33bbc ("ipv6: sr: implement several seg6local actions")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Andrea Mayer [Tue, 12 Jul 2022 17:58:35 +0000 (19:58 +0200)]
seg6: fix skb checksum evaluation in SRH encapsulation/insertion
Support for SRH encapsulation and insertion was introduced with
commit
6c8702c60b88 ("ipv6: sr: add support for SRH encapsulation and
injection with lwtunnels"), through the seg6_do_srh_encap() and
seg6_do_srh_inline() functions, respectively.
The former encapsulates the packet in an outer IPv6 header along with
the SRH, while the latter inserts the SRH between the IPv6 header and
the payload. Then, the headers are initialized/updated according to the
operating mode (i.e., encap/inline).
Finally, the skb checksum is calculated to reflect the changes applied
to the headers.
The IPv6 payload length ('payload_len') is not initialized
within seg6_do_srh_{inline,encap}() but is deferred in seg6_do_srh(), i.e.
the caller of seg6_do_srh_{inline,encap}().
However, this operation invalidates the skb checksum, since the
'payload_len' is updated only after the checksum is evaluated.
To solve this issue, the initialization of the IPv6 payload length is
moved from seg6_do_srh() directly into the seg6_do_srh_{inline,encap}()
functions and before the skb checksum update takes place.
Fixes:
6c8702c60b88 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/all/20220705190727.69d532417be7438b15404ee1@uniroma2.it
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Xiubo Li [Mon, 11 Jul 2022 04:11:21 +0000 (12:11 +0800)]
netfs: do not unlock and put the folio twice
check_write_begin() will unlock and put the folio when return
non-zero. So we should avoid unlocking and putting it twice in
netfs layer.
Change the way ->check_write_begin() works in the following two ways:
(1) Pass it a pointer to the folio pointer, allowing it to unlock and put
the folio prior to doing the stuff it wants to do, provided it clears
the folio pointer.
(2) Change the return values such that 0 with folio pointer set means
continue, 0 with folio pointer cleared means re-get and all error
codes indicating an error (no special treatment for -EAGAIN).
[ bagasdotme: use Sphinx code text syntax for *foliop pointer ]
Cc: stable@vger.kernel.org
Link: https://tracker.ceph.com/issues/56423
Link: https://lore.kernel.org/r/cf169f43-8ee7-8697-25da-0204d1b4343e@redhat.com
Co-developed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Alexandre Chartre [Wed, 13 Jul 2022 19:58:08 +0000 (21:58 +0200)]
x86/entry: Remove UNTRAIN_RET from native_irq_return_ldt
UNTRAIN_RET is not needed in native_irq_return_ldt because RET
untraining has already been done at this point.
In addition, when the RETBleed mitigation is IBPB, UNTRAIN_RET clobbers
several registers (AX, CX, DX) so here it trashes user values which are
in these registers.
Signed-off-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/35b0d50f-12d1-10c3-f5e8-d6c140486d4a@oracle.com
Jiapeng Chong [Thu, 14 Jul 2022 07:29:39 +0000 (15:29 +0800)]
x86/bugs: Mark retbleed_strings static
This symbol is not used outside of bugs.c, so mark it static.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220714072939.71162-1-jiapeng.chong@linux.alibaba.com
Changyuan Lyu [Fri, 8 Jul 2022 20:50:26 +0000 (13:50 -0700)]
scsi: pm80xx: Set stopped phy's linkrate to Disabled
Negotiated link rate needs to be updated to 'Disabled' when phy is stopped.
Link: https://lore.kernel.org/r/20220708205026.969161-1-changyuanl@google.com
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Changyuan Lyu <changyuanl@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>