OSDN Git Service
Po Liu [Fri, 15 Nov 2019 03:33:33 +0000 (03:33 +0000)]
enetc: Configure the Time-Aware Scheduler via tc-taprio offload
ENETC supports in hardware for time-based egress shaping according
to IEEE 802.1Qbv. This patch implement the Qbv enablement by the
hardware offload method qdisc tc-taprio method.
Also update cbdr writeback to up level since control bd ring may
writeback data to control bd ring.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan Lemon [Thu, 14 Nov 2019 22:13:00 +0000 (14:13 -0800)]
page_pool: do not release pool until inflight == 0.
The page pool keeps track of the number of pages in flight, and
it isn't safe to remove the pool until all pages are returned.
Disallow removing the pool until all pages are back, so the pool
is always available for page producers.
Make the page pool responsible for its own delayed destruction
instead of relying on XDP, so the page pool can be used without
the xdp memory model.
When all pages are returned, free the pool and notify xdp if the
pool is registered with the xdp memory system. Have the callback
perform a table walk since some drivers (cpsw) may share the pool
among multiple xdp_rxq_info.
Note that the increment of pages_state_release_cnt may result in
inflight == 0, resulting in the pool being released.
Fixes:
d956a048cd3f ("xdp: force mem allocator removal and periodic warning")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 16 Nov 2019 20:26:49 +0000 (12:26 -0800)]
Merge branch 'smc-last-part-of-termination-improvements'
Karsten Graul says:
====================
last part of termination improvements
Patches 1 and 2 finish the set of termination patches, introducing
a reboot handler that terminates all link groups. Patch 3 adds an
rcu_barrier before the module is unloaded, and patch 4 is cleanup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Sat, 16 Nov 2019 16:47:32 +0000 (17:47 +0100)]
net/smc: remove unused constant
Constant SMC_CLOSE_WAIT_LISTEN_CLCSOCK_TIME is defined, but since
commit
3d502067599f ("net/smc: simplify wait when closing listen socket")
no longer used. Remove it.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Sat, 16 Nov 2019 16:47:31 +0000 (17:47 +0100)]
net/smc: use rcu_barrier() on module unload
Add rcu_barrier() to make sure no RCU readers or callbacks are
pending when the module is unloaded.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Sat, 16 Nov 2019 16:47:30 +0000 (17:47 +0100)]
net/smc: guarantee removal of link groups in reboot
When rebooting it should be guaranteed all link groups are cleaned
up and freed.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Sat, 16 Nov 2019 16:47:29 +0000 (17:47 +0100)]
net/smc: introduce bookkeeping of SMCR link groups
If the smc module is unloaded return control from exit routine only,
if all link groups are freed.
If an IB device is thrown away return control from device removal only,
if all link groups belonging to this device are freed.
Counters for the total number of SMCR link groups and for the total
number of SMCR links per IB device are introduced. smc module unloading
continues only if the total number of SMCR link groups is zero. IB device
removal continues only it the total number of SMCR links per IB device
has decreased to zero.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petar Penkov [Thu, 14 Nov 2019 17:52:09 +0000 (09:52 -0800)]
tun: fix data-race in gro_normal_list()
There is a race in the TUN driver between napi_busy_loop and
napi_gro_frags. This commit resolves the race by adding the NAPI struct
via netif_tx_napi_add, instead of netif_napi_add, which disables polling
for the NAPI struct.
KCSAN reported:
BUG: KCSAN: data-race in gro_normal_list.part.0 / napi_busy_loop
write to 0xffff8880b5d474b0 of 4 bytes by task 11205 on cpu 0:
gro_normal_list.part.0+0x77/0xb0 net/core/dev.c:5682
gro_normal_list net/core/dev.c:5678 [inline]
gro_normal_one net/core/dev.c:5692 [inline]
napi_frags_finish net/core/dev.c:5705 [inline]
napi_gro_frags+0x625/0x770 net/core/dev.c:5778
tun_get_user+0x2150/0x26a0 drivers/net/tun.c:1976
tun_chr_write_iter+0x79/0xd0 drivers/net/tun.c:2022
call_write_iter include/linux/fs.h:1895 [inline]
do_iter_readv_writev+0x487/0x5b0 fs/read_write.c:693
do_iter_write fs/read_write.c:970 [inline]
do_iter_write+0x13b/0x3c0 fs/read_write.c:951
vfs_writev+0x118/0x1c0 fs/read_write.c:1015
do_writev+0xe3/0x250 fs/read_write.c:1058
__do_sys_writev fs/read_write.c:1131 [inline]
__se_sys_writev fs/read_write.c:1128 [inline]
__x64_sys_writev+0x4e/0x60 fs/read_write.c:1128
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
read to 0xffff8880b5d474b0 of 4 bytes by task 11168 on cpu 1:
gro_normal_list net/core/dev.c:5678 [inline]
napi_busy_loop+0xda/0x4f0 net/core/dev.c:6126
sk_busy_loop include/net/busy_poll.h:108 [inline]
__skb_recv_udp+0x4ad/0x560 net/ipv4/udp.c:1689
udpv6_recvmsg+0x29e/0xe90 net/ipv6/udp.c:288
inet6_recvmsg+0xbb/0x240 net/ipv6/af_inet6.c:592
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1889 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
ksys_read+0xd5/0x1b0 fs/read_write.c:587
__do_sys_read fs/read_write.c:597 [inline]
__se_sys_read fs/read_write.c:595 [inline]
__x64_sys_read+0x4c/0x60 fs/read_write.c:595
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 11168 Comm: syz-executor.0 Not tainted 5.4.0-rc6+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes:
943170998b20 ("tun: enable NAPI for TUN/TAP driver")
Signed-off-by: Petar Penkov <ppenkov@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 14 Nov 2019 16:43:27 +0000 (08:43 -0800)]
selftests: net: tcp_mmap should create detached threads
Since we do not plan using pthread_join() in the server do_accept()
loop, we better create detached threads, or risk increasing memory
footprint over time.
Fixes:
192dc405f308 ("selftests: net: add tcp_mmap program")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tonghao Zhang [Thu, 14 Nov 2019 15:51:08 +0000 (23:51 +0800)]
net: openvswitch: don't call pad_packet if not necessary
The nla_put_u16/nla_put_u32 makes sure that
*attrlen is align. The call tree is that:
nla_put_u16/nla_put_u32
-> nla_put attrlen = sizeof(u16) or sizeof(u32)
-> __nla_put attrlen
-> __nla_reserve attrlen
-> skb_put(skb, nla_total_size(attrlen))
nla_total_size returns the total length of attribute
including padding.
Cc: Joe Stringer <joe@ovn.org>
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 15 Nov 2019 20:32:17 +0000 (12:32 -0800)]
Merge branch 'DSA-driver-for-Vitesse-Felix-switch'
Vladimir Oltean says:
====================
DSA driver for Vitesse Felix switch
This series builds upon the previous "Accomodate DSA front-end into
Ocelot" topic and does the following:
- Reworks the Ocelot (VSC7514) driver to support one more switching core
(VSC9959), used in NPI mode. Some code which was thought to be
SoC-specific (ocelot_board.c) wasn't, and vice versa, so it is being
accordingly moved.
- Exports ocelot driver structures and functions to include/soc/mscc.
- Adds a DSA ocelot front-end for VSC9959, which is a PCI device and
uses the exported ocelot functionality for hardware configuration.
- Adds a tagger driver for the Vitesse injection/extraction DSA headers.
This is known to be compatible with at least Ocelot and Felix.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 14 Nov 2019 15:03:30 +0000 (17:03 +0200)]
net: dsa: ocelot: add driver for Felix switch family
This supports an Ethernet switching core from Vitesse / Microsemi /
Microchip (VSC9959) which is part of the Ocelot family (a brand name),
and whose code name is Felix. The switch can be (and is) integrated on
different SoCs as a PCIe endpoint device.
The functionality is provided by the core of the Ocelot switch driver
(drivers/net/ethernet/mscc). In this regard, the current driver is an
instance of Microsemi's Ocelot core driver, with a DSA front-end. It
inherits its name from VSC9959's code name, to distinguish itself from
the switchdev ocelot driver.
The patch adds the logic for probing a PCI device and defines the
register map for the VSC9959 switch core, since it has some differences
in register addresses and bitfield mappings compared to the other Ocelot
switches (VSC7511, VSC7512, VSC7513, VSC7514).
The Felix driver declares the register map as part of the "instance
table". Currently the VSC9959 inside NXP LS1028A is the only instance,
but presumably it can support other switches in the Ocelot family, when
used in DSA mode (Linux running on the external CPU, and not on the
embedded MIPS).
In a few cases, some h/w operations have to be done differently on
VSC9959 due to missing bitfields. This is the case for the switch core
reset and init. Because for this operation Ocelot uses some bits that
are not present on Felix, the latter has to use a register from the
global registers block (GCB) instead.
Although it is a PCI driver, it relies on DT bindings for compatibility
with DSA (CPU port link, PHY library). It does not have any custom
device tree bindings, since we would like to minimize its dependency on
device tree though.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 14 Nov 2019 15:03:29 +0000 (17:03 +0200)]
net: dsa: ocelot: add tagger for Ocelot/Felix switches
While it is entirely possible that this tagger format is in fact more
generic than just these 2 switch families, I don't have that knowledge.
The Seville switch in NXP T1040 has a similar frame format, but there
are enough differences (e.g. DEST field starts at bit 57 instead of 56)
that calling this file tag_vitesse.c is a bit of a stretch at the
moment. The frame format has been listed in a comment so that people who
add support for further Vitesse switches can rework this tagger while
keeping compatibility with Felix.
The "ocelot" name was chosen instead of "felix" because even the Ocelot
switch can act as a DSA device when it is used in NPI mode, and the Felix
tagger format is almost identical. Currently it is only used for the
Felix switch embedded in the NXP LS1028A chip.
The ABI for this tagger should be considered "not stable" at the moment.
The DSA tag is always placed before the Ethernet header and therefore,
we are using the long prefix for RX tags to avoid putting the DSA master
port in promiscuous mode. Once there will be an API in DSA for drivers
to request DSA masters to be in promiscuous mode unconditionally, we
will switch to the "no prefix" extraction frame header, which will save
16 padding bytes for each RX frame.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 14 Nov 2019 15:03:28 +0000 (17:03 +0200)]
net: mscc: ocelot: publish ocelot_sys.h to include/soc/mscc
The Felix DSA driver needs to write to SYS_RAM_INIT_RAM_INIT for its own
chip initialization process.
Also update the MAINTAINERS file such that the headers exported by the
ocelot driver are under the same maintainers' umbrella as the driver
itself.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 14 Nov 2019 15:03:27 +0000 (17:03 +0200)]
net: mscc: ocelot: publish structure definitions to include/soc/mscc/ocelot.h
We will be registering another switch driver based on ocelot, which
lives under drivers/net/dsa.
Make sure the Felix DSA front-end has the necessary abstractions to
implement a new Ocelot driver instantiation. This includes the function
prototypes for implementing DSA callbacks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 14 Nov 2019 15:03:26 +0000 (17:03 +0200)]
net: mscc: ocelot: separate the implementation of switch reset
The Felix switch has a different reset procedure, so a function pointer
needs to be created and added to the ocelot_ops structure.
The reset procedure has been moved into ocelot_init.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 14 Nov 2019 15:03:25 +0000 (17:03 +0200)]
net: mscc: ocelot: adjust MTU on the CPU port in NPI mode
When using the NPI port, the DSA tag is passed through Ethernet, so the
switch's MAC needs to accept it as it comes from the DSA master. Increase
the MTU on the external CPU port to account for the length of the
injection header.
Without this patch, MTU-sized frames are dropped by the switch's CPU
port on xmit, which is especially obvious in TCP sessions.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 14 Nov 2019 15:03:24 +0000 (17:03 +0200)]
net: mscc: ocelot: export a constant for the tag length in bytes
This constant will be used in a future patch to increase the MTU on NPI
ports, and will also be used in the tagger driver for Felix.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 14 Nov 2019 15:03:23 +0000 (17:03 +0200)]
net: mscc: ocelot: create a helper for changing the port MTU
Since in an NPI/DSA setup, not all ports will have the same MTU, we need
to make sure the watermarks for pause frames and/or tail dropping logic
that existed in the driver is still coherent for the new MTU values.
We need to do this because the NPI (aka external CPU) port needs an
increased MTU for the DSA tag. This will be done in a future patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 14 Nov 2019 15:03:22 +0000 (17:03 +0200)]
net: mscc: ocelot: move invariant configs out of adjust_link
It doesn't make sense to rewrite all these registers every time the PHY
library notifies us about a link state change.
In a future patch we will customize the MTU for the CPU port, and since
the MTU was previously configured from adjust_link, if we don't make
this change, its value would have got overridden.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Thu, 14 Nov 2019 15:03:21 +0000 (17:03 +0200)]
net: mscc: ocelot: filter out ocelot SoC specific PCS config from common path
The adjust_link routine should be generic enough to be (re)used by
any SoC that integrates a switch core compatible with the Ocelot
core switch driver. Currently all configurations are generic except
for the PCS settings that are SoC specific. Move these out to the
Ocelot SoC/board instance.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Thu, 14 Nov 2019 15:03:20 +0000 (17:03 +0200)]
net: mscc: ocelot: move resource ioremap and regmap init to common code
Let's make this ioremap and regmap init code common. It should not
be platform dependent as it should be usable by PCI devices too.
Use better names where necessary to avoid clashes.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 15 Nov 2019 20:28:28 +0000 (12:28 -0800)]
Merge branch 'net-smc-improve-termination-handling-part-3'
Karsten Graul says:
====================
net/smc: improve termination handling (part 3)
Part 3 of the SMC termination patches improves the link group
termination processing and introduces the ability to immediately
terminate a link group.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Thu, 14 Nov 2019 12:02:47 +0000 (13:02 +0100)]
net/smc: immediate termination for SMCR link groups
If the SMC module is unloaded or an IB device is thrown away, the
immediate link group freeing introduced for SMCD is exploited for SMCR
as well. That means SMCR-specifics are added to smc_conn_kill().
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Thu, 14 Nov 2019 12:02:46 +0000 (13:02 +0100)]
net/smc: wait for tx completions before link freeing
Make sure all pending work requests are completed before freeing
a link.
Dismiss tx pending slots already when terminating a link group to
exploit termination shortcut in tx completion queue handler.
And kill the completion queue tasklets after destroy of the
completion queues, otherwise there is a time window for another
tasklet schedule of an already killed tasklet.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Thu, 14 Nov 2019 12:02:45 +0000 (13:02 +0100)]
net/smc: abnormal termination without orderly flag
For abnormal termination issue an LLC DELETE_LINK without the
orderly flag.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Thu, 14 Nov 2019 12:02:44 +0000 (13:02 +0100)]
net/smc: no WR buffer wait for terminating link group
Avoid waiting for a free work request buffer, if the link group
is already terminating.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Thu, 14 Nov 2019 12:02:43 +0000 (13:02 +0100)]
net/smc: introduce bookkeeping of SMCD link groups
If the ism module is unloaded return control from exit routine only,
if all link groups are freed.
If an IB device is thrown away return control from device removal only,
if all link groups belonging to this device are freed.
A counters for the total number of SMCD link groups per ISM device is
introduced. ism module unloading continues only if the total number of
SMCD link groups for all ISM devices is zero. ISM device
removal continues only it the total number of SMCD link groups per ISM
device has decreased to zero.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Thu, 14 Nov 2019 12:02:42 +0000 (13:02 +0100)]
net/smc: abnormal termination of SMCD link groups
A final cleanup due to SMCD device removal means immediate freeing
of all link groups belonging to this device in interrupt context.
This patch introduces a separate SMCD link group termination routine,
which terminates all link groups of an SMCD device.
This new routine smcd_terminate_all ()is reused if the smc module is
unloaded.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Thu, 14 Nov 2019 12:02:41 +0000 (13:02 +0100)]
net/smc: immediate termination for SMCD link groups
SMCD link group termination is called when peer signals its shutdown
of its corresponding link group. For regular shutdowns no connections
exist anymore. For abnormal shutdowns connections must be killed and
their DMBs must be unregistered immediately. That means the SMCR method
to delay the link group freeing several seconds does not fit.
This patch adds immediate termination of a link group and its SMCD
connections and makes sure all SMCD link group related cleanup steps
are finished.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Thu, 14 Nov 2019 12:02:40 +0000 (13:02 +0100)]
net/smc: fix final cleanup sequence for SMCD devices
If peer announces shutdown, use the link group terminate worker for
local cleanup of link groups and connections to terminate link group
in proper context.
Make sure link groups are cleaned up first before destroying the
event queue of the SMCD device, because link group cleanup may
raise events.
Send signal shutdown only if peer has not done it already.
Send socket abort or close only, if peer has not already announced
shutdown.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 15 Nov 2019 20:25:42 +0000 (12:25 -0800)]
Merge branch 'net-stmmac-CPU-Performance-Improvements'
Jose Abreu says:
====================
net: stmmac: CPU Performance Improvements
CPU Performance improvements for stmmac. Please check bellow for results
before and after the series.
Patch 1/7, allows RX Interrupt on Completion to be disabled and only use the
RX HW Watchdog.
Patch 2/7, setups the default RX coalesce settings instead of using the
minimum value.
Patch 3/7 and 4/7, removes the uneeded computations for RX Flow Control
activation/de-activation, on some cases.
Patch 5/7, tunes-up the default coalesce settings.
Patch 6/7, re-works the TX coalesce timer activation logic.
Patch 7/7, removes the now uneeded TBU interrupt.
NetPerf UDP Results:
--------------------
Socket Message Elapsed Messages CPU Service
Size Size Time Okay Errors Throughput Util Demand
bytes bytes secs # # 10^6bits/sec % SS us/KB
--- XGMAC@2.5G: Before
212992 1400 10.00
2100620 0 2351.7 36.69 5.112
212992 10.00
2100539 2351.6 26.18 3.648
--- XGMAC@2.5G: After
212992 1400 10.00
2108972 0 2361.5 21.73 3.015
212992 10.00
2097038 2348.1 19.21 2.666
--- GMAC5@1G: Before
212992 1400 10.00 786000 0 880.2 34.71 12.923
212992 10.00 786000 880.2 23.42 8.719
--- GMAC5@1G: After
212992 1400 10.00 842648 0 943.7 14.12 4.903
212992 10.00 842648 943.7 12.73 4.418
Perf TCP Results on RX Path:
----------------------------
--- XGMAC@2.5G: Before
22.51% swapper [stmmac] [k] dwxgmac2_dma_interrupt
10.82% swapper [stmmac] [k] dwxgmac2_host_mtl_irq_status
5.21% swapper [stmmac] [k] dwxgmac2_host_irq_status
4.67% swapper [stmmac] [k] dwxgmac3_safety_feat_irq_status
3.63% swapper [kernel.kallsyms] [k] stack_trace_consume_entry
2.74% iperf3 [kernel.kallsyms] [k] copy_user_enhanced_fast_string
2.52% swapper [kernel.kallsyms] [k] update_stack_state
1.94% ksoftirqd/0 [stmmac] [k] dwxgmac2_dma_interrupt
1.45% iperf3 [kernel.kallsyms] [k] queued_spin_lock_slowpath
1.26% swapper [kernel.kallsyms] [k] create_object
--- XGMAC@2.5G: After
7.43% swapper [kernel.kallsyms] [k] stack_trace_consume_entry
5.86% swapper [stmmac] [k] dwxgmac2_dma_interrupt
5.68% swapper [kernel.kallsyms] [k] update_stack_state
4.71% iperf3 [kernel.kallsyms] [k] copy_user_enhanced_fast_string
2.88% swapper [kernel.kallsyms] [k] create_object
2.69% swapper [stmmac] [k] dwxgmac2_host_mtl_irq_status
2.61% swapper [stmmac] [k] stmmac_napi_poll_rx
2.52% swapper [kernel.kallsyms] [k] unwind_next_frame.part.4
1.48% swapper [kernel.kallsyms] [k] unwind_get_return_address
1.38% swapper [kernel.kallsyms] [k] arch_stack_walk
--- GMAC5@1G: Before
31.29% swapper [stmmac] [k] dwmac4_dma_interrupt
14.57% swapper [stmmac] [k] dwmac4_irq_mtl_status
10.66% swapper [stmmac] [k] dwmac4_irq_status
1.97% swapper [kernel.kallsyms] [k] stack_trace_consume_entry
1.73% iperf3 [kernel.kallsyms] [k] copy_user_enhanced_fast_string
1.59% swapper [kernel.kallsyms] [k] update_stack_state
1.15% iperf3 [kernel.kallsyms] [k] do_syscall_64
1.01% ksoftirqd/0 [stmmac] [k] dwmac4_dma_interrupt
0.89% swapper [kernel.kallsyms] [k] __default_send_IPI_dest_field
0.75% swapper [stmmac] [k] stmmac_napi_poll_rx
--- GMAC5@1G: After
6.70% swapper [kernel.kallsyms] [k] stack_trace_consume_entry
5.79% swapper [stmmac] [k] dwmac4_dma_interrupt
5.29% swapper [kernel.kallsyms] [k] update_stack_state
3.52% iperf3 [kernel.kallsyms] [k] copy_user_enhanced_fast_string
2.83% swapper [stmmac] [k] dwmac4_irq_mtl_status
2.62% swapper [kernel.kallsyms] [k] create_object
2.46% swapper [stmmac] [k] stmmac_napi_poll_rx
2.32% swapper [kernel.kallsyms] [k] unwind_next_frame.part.4
2.19% swapper [stmmac] [k] dwmac4_irq_status
1.39% swapper [kernel.kallsyms] [k] unwind_get_return_address
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Thu, 14 Nov 2019 11:42:51 +0000 (12:42 +0100)]
net: stmmac: xgmac: Do not enable TBU interrupt
Now that TX Coalesce has been rewritten we no longer need this
additional interrupt enabled. This reduces CPU usage.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Thu, 14 Nov 2019 11:42:50 +0000 (12:42 +0100)]
net: stmmac: Rework TX Coalesce logic
Coalesce logic currently increments the number of packets and sets the
IC bit when the coalesced packets have passed a given limit. This does
not reflect very well what coalesce was meant for as we can have a large
number of packets that are coalesced and then a single one, sent later
on that has the IC bit.
Rework the logic so that it coalesces only upon a limit of packets and
sets the IC bit for large number of packets.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Thu, 14 Nov 2019 11:42:49 +0000 (12:42 +0100)]
net: stmmac: Tune-up default coalesce settings
Tune-up the defalt coalesce settings for optimal values. This gives the
best performance in most of the use-cases.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Thu, 14 Nov 2019 11:42:48 +0000 (12:42 +0100)]
net: stmmac: xgmac: Remove uneeded computation for RFA/RFD
RFA and RFD should not be dependent on FIFO size. In fact, the more FIFO
space we have, the later we can activate Flow Control. Let's use
hard-coded values for RFA and RFD for all FIFO sizes with the exception
of 4k, which is a special case.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Thu, 14 Nov 2019 11:42:47 +0000 (12:42 +0100)]
net: stmmac: gmac4+: Remove uneeded computation for RFA/RFD
RFA and RFD should not be dependent on FIFO size. In fact, the more FIFO
space we have, the later we can activate Flow Control. Let's use
hard-coded values for RFA and RFD for all FIFO sizes with the exception
of 4k, which is a special case.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Thu, 14 Nov 2019 11:42:46 +0000 (12:42 +0100)]
net: stmmac: Setup a default RX Coalesce value instead of the minimum
For performance reasons, sometimes using the minimum RX Coalesce value
is not optimal. Lets setup a default value that is optimal in most of
the use cases.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Thu, 14 Nov 2019 11:42:45 +0000 (12:42 +0100)]
net: stmmac: Do not set RX IC bit if RX Coalesce is zero
We may only want to use the RX Watchdog so lets check if RX Coalesce
settings are non-zero and only set the RX Interrupt on Completion bit if
its not.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 14 Nov 2019 09:54:19 +0000 (11:54 +0200)]
mlxsw: spectrum_router: Allocate discard adjacency entry when needed
Commit
0c3cbbf96def ("mlxsw: Add specific trap for packets routed via
invalid nexthops") allocated an adjacency entry during driver
initialization whose purpose is to discard packets hitting the route
pointing to it.
These adjacency entries are allocated from a resource called KVD linear
(KVDL). There are situations in which the user can decide to set the
size of this resource (via devlink-resource) to 0, in which case the
driver will not be able to load.
Therefore, instead of pre-allocating this adjacency entry, simply
allocate it only when needed. A variable indicating the validity of the
entry is added and is used to ensure it is only allocated and written
once and that it is freed after all the routes were flushed.
Fixes:
0c3cbbf96def ("mlxsw: Add specific trap for packets routed via invalid nexthops")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Thu, 14 Nov 2019 07:39:46 +0000 (15:39 +0800)]
net/tls: Fix unused function warning
If PROC_FS is not set, gcc warning this:
net/tls/tls_proc.c:23:12: warning:
'tls_statistics_seq_show' defined but not used [-Wunused-function]
Use #ifdef to guard this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 15 Nov 2019 02:16:51 +0000 (18:16 -0800)]
Merge branch 's390-next'
Julian Wiedmann says:
====================
s390/qeth: updates 2019-11-14
please apply the following qeth patches to net-next.
Along with the usual cleanups, this
(1) reduces collateral packet loss in the RX path when dealing with
bad packets and/or allocation errors, and
(2) simplifies how the L3 driver deals with mcast IP addresses.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 14 Nov 2019 10:19:24 +0000 (11:19 +0100)]
s390/qeth: don't check drvdata in sysfs code
Given the way how the sysfs attributes are registered / unregistered,
the show/store helpers will never be called with a NULL drvdata.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 14 Nov 2019 10:19:23 +0000 (11:19 +0100)]
s390/qeth: replace qeth_l3_get_addr_buffer()
The remaining usage effectively is a kmemdup() of the query object.
By not wrapping it, some of the callers can now use GFP_KERNEL for the
allocation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 14 Nov 2019 10:19:22 +0000 (11:19 +0100)]
s390/qeth: remove VLAN tracking for L3 devices
Use vlan_for_each() instead of tracking each registered VID internally.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 14 Nov 2019 10:19:21 +0000 (11:19 +0100)]
s390/qeth: consolidate L3 mcast registration code
Current code processes each (VLAN) device twice - once to inspect the
IPv4 mcast addresses, and then a second time to walk the IPv6 mcast
addresses. Unify all this into a single helper, thus removing some
checks and a duplicated VLAN lookup.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 14 Nov 2019 10:19:20 +0000 (11:19 +0100)]
s390/qeth: remove gratuitious RX modeset
Trust the IPv4/IPv6 code to properly remove its mcast addresses when a
VLAN device is unregistered, and then also trigger an RX modeset
whenever it's needed.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 14 Nov 2019 10:19:19 +0000 (11:19 +0100)]
s390/qeth: fine-tune L3 mcast locking
Push the inet6_dev locking down into the helper that actually needs it
for walking the mc_list.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 14 Nov 2019 10:19:18 +0000 (11:19 +0100)]
s390/qeth: clean up error path in qeth_core_probe_device()
qeth_core_free_card() is meant to be the counterpart of
qeth_alloc_card() - but unfortunately was also picked as the place
to free the QDIO queues.
This gets messy when qeth_core_probe_device() fails during
qeth_add_dbf_entry(). At this point the card->qdio.state is not initialized
yet, so qeth_free_qdio_queues() ends up operating on uninitialized data.
Luckily for now, the whole qeth_card struct is zero-allocated and the value
of the QETH_QDIO_UNINITIALIZED enum is 0 as well. So there's no real impact
from this bug at the moment, it's just really fragile.
Clean this up by moving the qeth_free_qdio_queues() call up one level in
the hierarchy. This way it doesn't get called from the error path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 14 Nov 2019 10:19:17 +0000 (11:19 +0100)]
s390/qeth: handle skb allocation error gracefully
When current code fails to allocate an skb in the RX path, it drops the
whole RX buffer. Considering the large number of packets that a single
RX buffer might contain, this is quite drastic.
Skip over the packet instead, and try to extract the next packet from
the RX buffer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 14 Nov 2019 10:19:16 +0000 (11:19 +0100)]
s390/qeth: drop unwanted packets earlier in RX path
Packets with an unexpected HW format are currently first extracted from
the RX buffer, passed upwards to the layer-specific driver and only then
finally dropped.
Enhance the RX path so that we can drop such packets before even
allocating an skb. For this, add some additional logic so that when a
packet is meant to be dropped, we can still walk along the packet's data
chunks in the RX buffer. This allows us to extract the following
packet(s) from the buffer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 14 Nov 2019 10:19:15 +0000 (11:19 +0100)]
s390/qeth: support per-frame invalidation
Each RX buffer may contain up to 64KB worth of data. In case the device
needs to discard a packet _after_ already having reserved space for it
in the buffer, the whole buffer gets set to ERROR state. As the buffer
might contain any number of good packets, this can result in collateral
packet loss.
qeth can provide relief by enabling per-frame invalidation. The RX
buffer is then presented as usual, we just need to spot & drop any
individual packet that was flagged as invalid.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 14 Nov 2019 10:19:14 +0000 (11:19 +0100)]
s390/qeth: gather more detailed RX dropped/error statistics
Where available, use the fine-grained counters in rtnl_link_stats64 to
indicate different RX error causes. For drop reasons, use driver-private
ethtool counters.
In particular this patch allows us to keep track of driver-side drops due
to unknown/unsupported HW descriptor format.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 15 Nov 2019 02:12:19 +0000 (18:12 -0800)]
Merge branch 'vsock-add-multi-transports-support'
Stefano Garzarella says:
====================
vsock: add multi-transports support
Most of the patches are reviewed by Dexuan, Stefan, and Jorgen.
The following patches need reviews:
- [11/15] vsock: add multi-transports support
- [12/15] vsock/vmci: register vmci_transport only when VMCI guest/host
are active
- [15/15] vhost/vsock: refuse CID assigned to the guest->host transport
RFC: https://patchwork.ozlabs.org/cover/
1168442/
v1: https://patchwork.ozlabs.org/cover/
1181986/
v1 -> v2:
- Patch 11:
+ vmci_transport: sent reset when vsock_assign_transport() fails
[Jorgen]
+ fixed loopback in the guests, checking if the remote_addr is the
same of transport_g2h->get_local_cid()
+ virtio_transport_common: updated space available while creating
the new child socket during a connection request
- Patch 12:
+ removed 'features' variable in vmci_transport_init() [Stefan]
+ added a flag to register only once the host [Jorgen]
- Added patch 15 to refuse CID assigned to the guest->host transport in
the vhost_transport
This series adds the multi-transports support to vsock, following
this proposal: https://www.spinics.net/lists/netdev/msg575792.html
With the multi-transports support, we can use VSOCK with nested VMs
(using also different hypervisors) loading both guest->host and
host->guest transports at the same time.
Before this series, vmci_transport supported this behavior but only
using VMware hypervisor on L0, L1, etc.
The first 9 patches are cleanups and preparations, maybe some of
these can go regardless of this series.
Patch 10 changes the hvs_remote_addr_init(). setting the
VMADDR_CID_HOST as remote CID instead of VMADDR_CID_ANY to make
the choice of transport to be used work properly.
Patch 11 adds multi-transports support.
Patch 12 changes a little bit the vmci_transport and the vmci driver
to register the vmci_transport only when there are active host/guest.
Patch 13 prevents the transport modules unloading while sockets are
assigned to them.
Patch 14 fixes an issue in the bind() logic discoverable only with
the new multi-transport support.
Patch 15 refuses CID assigned to the guest->host transport in the
vhost_transport.
I've tested this series with nested KVM (vsock-transport [L0,L1],
virtio-transport[L1,L2]) and with VMware (L0) + KVM (L1)
(vmci-transport [L0,L1], vhost-transport [L1], virtio-transport[L2]).
Dexuan successfully tested the RFC series on HyperV with a Linux guest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Thu, 14 Nov 2019 09:57:50 +0000 (10:57 +0100)]
vhost/vsock: refuse CID assigned to the guest->host transport
In a nested VM environment, we have to refuse to assign to a nested
guest the same CID assigned to our guest->host transport.
In this way, the user can use the local CID for loopback.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Thu, 14 Nov 2019 09:57:49 +0000 (10:57 +0100)]
vsock: fix bind() behaviour taking care of CID
When we are looking for a socket bound to a specific address,
we also have to take into account the CID.
This patch is useful with multi-transports support because it
allows the binding of the same port with different CID, and
it prevents a connection to a wrong socket bound to the same
port, but with different CID.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Thu, 14 Nov 2019 09:57:48 +0000 (10:57 +0100)]
vsock: prevent transport modules unloading
This patch adds 'module' member in the 'struct vsock_transport'
in order to get/put the transport module. This prevents the
module unloading while sockets are assigned to it.
We increase the module refcnt when a socket is assigned to a
transport, and we decrease the module refcnt when the socket
is destructed.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Thu, 14 Nov 2019 09:57:47 +0000 (10:57 +0100)]
vsock/vmci: register vmci_transport only when VMCI guest/host are active
To allow other transports to be loaded with vmci_transport,
we register the vmci_transport as G2H or H2G only when a VMCI guest
or host is active.
To do that, this patch adds a callback registered in the vmci driver
that will be called when the host or guest becomes active.
This callback will register the vmci_transport in the VSOCK core.
Cc: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Thu, 14 Nov 2019 09:57:46 +0000 (10:57 +0100)]
vsock: add multi-transports support
This patch adds the support of multiple transports in the
VSOCK core.
With the multi-transports support, we can use vsock with nested VMs
(using also different hypervisors) loading both guest->host and
host->guest transports at the same time.
Major changes:
- vsock core module can be loaded regardless of the transports
- vsock_core_init() and vsock_core_exit() are renamed to
vsock_core_register() and vsock_core_unregister()
- vsock_core_register() has a feature parameter (H2G, G2H, DGRAM)
to identify which directions the transport can handle and if it's
support DGRAM (only vmci)
- each stream socket is assigned to a transport when the remote CID
is set (during the connect() or when we receive a connection request
on a listener socket).
The remote CID is used to decide which transport to use:
- remote CID <= VMADDR_CID_HOST will use guest->host transport;
- remote CID == local_cid (guest->host transport) will use guest->host
transport for loopback (host->guest transports don't support loopback);
- remote CID > VMADDR_CID_HOST will use host->guest transport;
- listener sockets are not bound to any transports since no transport
operations are done on it. In this way we can create a listener
socket, also if the transports are not loaded or with VMADDR_CID_ANY
to listen on all transports.
- DGRAM sockets are handled as before, since only the vmci_transport
provides this feature.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Thu, 14 Nov 2019 09:57:45 +0000 (10:57 +0100)]
hv_sock: set VMADDR_CID_HOST in the hvs_remote_addr_init()
Remote peer is always the host, so we set VMADDR_CID_HOST as
remote CID instead of VMADDR_CID_ANY.
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Thu, 14 Nov 2019 09:57:44 +0000 (10:57 +0100)]
vsock: move vsock_insert_unbound() in the vsock_create()
vsock_insert_unbound() was called only when 'sock' parameter of
__vsock_create() was not null. This only happened when
__vsock_create() was called by vsock_create().
In order to simplify the multi-transports support, this patch
moves vsock_insert_unbound() at the end of vsock_create().
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Thu, 14 Nov 2019 09:57:43 +0000 (10:57 +0100)]
vsock: add vsock_create_connected() called by transports
All transports call __vsock_create() with the same parameters,
most of them depending on the parent socket. In order to simplify
the VSOCK core APIs exposed to the transports, this patch adds
the vsock_create_connected() callable from transports to create
a new socket when a connection request is received.
We also unexported the __vsock_create().
Suggested-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Thu, 14 Nov 2019 09:57:42 +0000 (10:57 +0100)]
vsock: handle buffer_size sockopts in the core
virtio_transport and vmci_transport handle the buffer_size
sockopts in a very similar way.
In order to support multiple transports, this patch moves this
handling in the core to allow the user to change the options
also if the socket is not yet assigned to any transport.
This patch also adds the '.notify_buffer_size' callback in the
'struct virtio_transport' in order to inform the transport,
when the buffer_size is changed by the user. It is also useful
to limit the 'buffer_size' requested (e.g. virtio transports).
Acked-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Thu, 14 Nov 2019 09:57:41 +0000 (10:57 +0100)]
vsock: add 'struct vsock_sock *' param to vsock_core_get_transport()
Since now the 'struct vsock_sock' object contains a pointer to
the transport, this patch adds a parameter to the
vsock_core_get_transport() to return the right transport
assigned to the socket.
This patch modifies also the virtio_transport_get_ops(), that
uses the vsock_core_get_transport(), adding the
'struct vsock_sock *' parameter.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Thu, 14 Nov 2019 09:57:40 +0000 (10:57 +0100)]
vsock/virtio: add transport parameter to the virtio_transport_reset_no_sock()
We are going to add 'struct vsock_sock *' parameter to
virtio_transport_get_ops().
In some cases, like in the virtio_transport_reset_no_sock(),
we don't have any socket assigned to the packet received,
so we can't use the virtio_transport_get_ops().
In order to allow virtio_transport_reset_no_sock() to use the
'.send_pkt' callback from the 'vhost_transport' or 'virtio_transport',
we add the 'struct virtio_transport *' to it and to its caller:
virtio_transport_recv_pkt().
We moved the 'vhost_transport' and 'virtio_transport' definition,
to pass their address to the virtio_transport_recv_pkt().
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Thu, 14 Nov 2019 09:57:39 +0000 (10:57 +0100)]
vsock: add 'transport' member in the struct vsock_sock
As a preparation to support multiple transports, this patch adds
the 'transport' member at the 'struct vsock_sock'.
This new field is initialized during the creation in the
__vsock_create() function.
This patch also renames the global 'transport' pointer to
'transport_single', since for now we're only supporting a single
transport registered at run-time.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Thu, 14 Nov 2019 09:57:38 +0000 (10:57 +0100)]
vsock: remove include/linux/vm_sockets.h file
This header file now only includes the "uapi/linux/vm_sockets.h".
We can include directly it when needed.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Thu, 14 Nov 2019 09:57:37 +0000 (10:57 +0100)]
vsock: remove vm_sockets_get_local_cid()
vm_sockets_get_local_cid() is only used in virtio_transport_common.c.
We can replace it calling the virtio_transport_get_ops() and
using the get_local_cid() callback registered by the transport.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Thu, 14 Nov 2019 09:57:36 +0000 (10:57 +0100)]
vsock/vmci: remove unused VSOCK_DEFAULT_CONNECT_TIMEOUT
The VSOCK_DEFAULT_CONNECT_TIMEOUT definition was introduced with
commit
d021c344051af ("VSOCK: Introduce VM Sockets"), but it is
never used in the net/vmw_vsock/vmci_transport.c.
VSOCK_DEFAULT_CONNECT_TIMEOUT is used and defined in
net/vmw_vsock/af_vsock.c
Cc: Jorgen Hansen <jhansen@vmware.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 15 Nov 2019 02:09:16 +0000 (18:09 -0800)]
Merge branch 'octeontx2-af-Debugfs-support-and-updates-to-parser-profile'
Sunil Goutham says:
====================
octeontx2-af: Debugfs support and updates to parser profile
This patchset adds debugfs support to dump various HW state machine info
which helps in debugging issues. Info includes
- Current queue context, stats, resource utilization etc
- MCAM entry utilization, miss and pkt drop counter
- CGX ingress and egress stats
- Current RVU block allocation status
- etc.
Rest patches has changes wrt
- Updated packet parsing profile for parsing more protocols.
- RSS algorithms to include inner protocols while generating hash
- Handle current version of silicon's limitations wrt shaping, coloring
and fixed mapping of transmit limiter queue's configuration.
- Enable broadcast packet replication to PF and it's VFs.
- Support for configurable NDC cache waymask
- etc
Changes from v1:
Removed inline keyword for newly introduced APIs in few patches.
- Suggested by David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Subbaraya Sundeep [Thu, 14 Nov 2019 05:26:33 +0000 (10:56 +0530)]
octeontx2-af: Start/Stop traffic in CGX along with NPC
Traffic for a CGX mapped NIXLF can be stopped by disabling entries
in NPC MCAM or by configuring CGX and mailbox messages exist for the
two options. If traffic is stopped at CGX then VFs of that PF are
also effected hence CGX traffic should be started/stopped by
tracking all the users of it. This patch implements that CGX users
tracking. CGX is also configured along with NPC if required.
Also removed a check which mandates even number of LBK VFs.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Thu, 14 Nov 2019 05:26:32 +0000 (10:56 +0530)]
octeontx2-af: Add option to disable dynamic entry caching in NDC
A config option is added to disable caching of dynamic entries
like SQEs and stack pages. Also locks down all HW contexts in NDC,
preventing them from being evicted.
This option is useful when the queue count is large and there are
huge NDC cache misses. It's trade off between SQ context misses and
dynamically changing entries like SQE and stack page pointers.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geetha sowjanya [Thu, 14 Nov 2019 05:26:31 +0000 (10:56 +0530)]
octeontx2-af: Support configurable NDC cache way_mask
Each of the NIX/NPA LFs can choose which ways of their respective
NDC caches should be used to cache their contexts. This enables
flexible configurations like disabling caching for a LF, limiting
it's context to a certain set of ways etc etc. Separate way_mask
for NIX-TX and NIX-RX is not supported.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Thu, 14 Nov 2019 05:26:30 +0000 (10:56 +0530)]
octeontx2-af: Enable broadcast packet replication
Ingress packet replication support has been added to 96xx B0
silicon. This patch enables using that feature to replicate
ingress broadcast packets to PF and it's VFs.
Also fixed below issues
- VFs can also install NPC MCAM entry to forward broadcast pkts.
Otherwise, unless PF's interface is UP, VFs will not receive
bcast packets.
- NPC MCAM entry is disabled when PF and all it's VFs are down.
- Few corner cases in installing multicast entry list.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Thu, 14 Nov 2019 05:26:29 +0000 (10:56 +0530)]
octeontx2-af: Support fixed transmit scheduler topology
CN96xx initial silicon doesn't support all features pertaining to
NIX transmit scheduling and shaping.
- It supports a fixed topology of 1:1 mapped transmit
limiters at all levels.
- Supports DWRR only at SMQ/MDQ and TL1.
- Doesn't support shaping and coloring.
This patch adds HW capability structure by which each variant
and skew of silicon can be differentiated by their supported
features. And adds support for A0 silicon's transmit scheduler
capabilities or rather limitations.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kiran Kumar K [Thu, 14 Nov 2019 05:26:28 +0000 (10:56 +0530)]
octeontx2-af: Add more RSS algorithms
This patch adds support for few more RSS key types for flow key
algorithm to compute rss hash index.
Following flow key types have been added.
- Tunnel types like NVGRE, VXLAN, GENEVE.
- L2 offload type ETH_DMAC, Here we will consider only DMAC 6 bytes.
- And extension header IPV6_EXT (1 byte followed by IPV6 header
- Hashing inner protocol fields for inner DMAC, IPv4/v6, TCP, UDP, SCTP.
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nithin Dabilpuram [Thu, 14 Nov 2019 05:26:27 +0000 (10:56 +0530)]
octeontx2-af: Clear NPC MCAM entries before update
Writing into NPC MCAM1 and MCAM0 registers are suppressed if
they happened to form a reserved combination. Hence
clear and disable MCAM entries before update.
For HRM:
[CAM(1)]<n>=1, [CAM(0)]<n>=1: Reserved.
The reserved combination is not allowed. Hardware suppresses any
write to CAM(0) or CAM(1) that would result in the reserved combination for
any CAM bit.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hao Zheng [Thu, 14 Nov 2019 05:26:26 +0000 (10:56 +0530)]
octeontx2-af: Update NPC KPU packet parsing profile
Updated NPC KPU packet parsing profile with support for following
- Fragmentation support for IPv4 IPv6 outer header
- NIX instruction header support
- QinQ with TPID of 0x8100 as non inner most vlan tag, as legacy
network equipments still generate QinQ packets with this configuration.
- To better support RSS for tunnelled packets, udp based tunnel
protocols such as vxlan, vxlan-gpe, geneve and gtpu are now
captured into a separate layer E. Consequently, the inner
packet headers are pushed one layer down to LF, LG, and LH
accordingly.
- Support for rfc7510 mpls in udp. Up to 4 MPLS labels can be parsed
and captured in one layer LE.
- Parser support for DSA, extended DSA and eDSA tags right after
ethernet header by Marvell SOHO and Falcon switches. For extended
DSA and eDSA tags, a special PKIND of 62 is used, as these tags don't
contain a tpid field.
- Higig2 protocol header parsing support, added a NPC_LT_LA_HIGIG2_ETHER
for a combined header of HIGIG2 and Ethernet. Add a
NPC_LT_LA_IH_NIX_HIGIG2_ETHER for a combined header of nix_ih,
HIGIG2 and Ethernet on egress side. Also added 2 upper flags in LA to
indicate the presence of nix_ih and HIGIG2.
Other changes include
- IPv4.TTL==0 IPv6.HLIM==0 check
- Per RFC 1858, mark fragment offset == 1 as error
- TCP invalid flags check
- Separate error codes for outer and inner IPv4 checksum errors.
- Fix a parser error when KPU parses incoming IPSec ESP and AH packets
- NPC vtag capture/strip hardware expect tag pointer to point to
tpid/ethertype instead of tci. So move lb_ptr to point to tpid/ethertype.
- Fix npc parser error when parsing udp packets that don't have any payload.
- For a single MCAM entry to match on packets with one or stacked vlan tags
combine NPC_LT_LB_STAG and NPC_LT_LB_QINQ to NPC_LT_LB_STAG_QINQ.
- NVGRE to have a separate ltype LD_NVGRE instead of combined with LD_GRE.
- Reserve top LD/LTYPEs to support custom KPU profile fields.
Signed-off-by: Hao Zheng <haoz@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subbaraya Sundeep [Thu, 14 Nov 2019 05:26:25 +0000 (10:56 +0530)]
octeontx2-af: Add macro to generate mbox handlers declarations
For every mailbox handler added to rvu, we are adding a function
declaration in rvu header file. Cleaned this up by adding a macro
to generate these declarations automatically.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geetha sowjanya [Thu, 14 Nov 2019 05:26:24 +0000 (10:56 +0530)]
octeontx2-af: Sync hw mbox with bounce buffer.
If mailbox client has a bounce buffer or a intermediate buffer where
mbox messages are framed then copy them from there to HW buffer.
If 'mbase' and 'hw_mbase' are not same then assume 'mbase' points to
bounce buffer.
This patch also adds msg_size field to mbox header to copy only valid
data instead of whole buffer.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Thu, 14 Nov 2019 05:26:23 +0000 (10:56 +0530)]
octeontx2-af: Add mbox API to validate all responses
Added a new mailbox API which goes through all responses
to check their IDs and response codes.
Also added logic to prevent queuing multiple works to
process the same mailbox message. This scenario happens
when AF is processing a PF's request and menawhile PF
sends ACK to AF sent UP message, then mbox_hdr->num_msgs
in the PF->AF DOWN mbox region will be nonzero and AF
will end up processing PF's request again. This is fixed
by taking a backup of num_msgs counter and clearing the
same in the mbox region before scheduling work.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Thu, 14 Nov 2019 05:26:22 +0000 (10:56 +0530)]
octeontx2-af: Add NPC MCAM entry allocation status to debugfs
Added support to display current NPC MCAM entries and counter's allocation
status ín debugfs.
cat /sys/kernel/debug/octeontx2/npc/mcam_info' will dump following info
- MCAM Rx and Tx keysize
- Total MCAM entries and counters
- Current available count
- Count of number of MCAM entries and counters allocated
by a RVU PF/VF device.
Also, one NPC MCAM counter (last one) is reserved and mapped to
NPC RX_INTF's MISS_ACTION to count dropped packets due to no MCAM
entry match. This pkt drop counter can be checked via debugfs.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linu Cherian [Thu, 14 Nov 2019 05:26:21 +0000 (10:56 +0530)]
octeontx2-af: Add per CGX port level NIX Rx/Tx counters
A CGX port is shared by a RVU PF and it's VFs. These per
CGX port level NIX Rx/Tx counters are cumilative stats of
all NIXLFs sharing this port. These stats when compared
to CGX Rx/Tx stats helps in identifying pkts dropped within
the system, if any.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prakash Brahmajyosyula [Thu, 14 Nov 2019 05:26:20 +0000 (10:56 +0530)]
octeontx2-af: Add CGX LMAC stats to debugfs
This patch adds CGX LMAC physical interface or serdes Rx/Tx
packet stats to debugfs.
'cat cgx<idx>/lmac<idx>/stats' dumps the current interface link
status and Rx/Tx stats. Stats include pkt received/transmitted,
dropped, pause frames etc etc.
Signed-off-by: Prakash Brahmajyosyula <bprakash@marvell.com>
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prakash Brahmajyosyula [Thu, 14 Nov 2019 05:26:19 +0000 (10:56 +0530)]
octeontx2-af: Add NDC block stats to debugfs.
NDC is a data cache unit which caches NPA and NIX block's
aura/pool/RQ/SQ/CQ/etc contexts to reduce number of costly
DRAM accesses.
This patch adds support to dump cache's performance stats
like cache line hit/miss counters, average cycles taken for
accessing cached and non-cached data. This will help in
checking if NPA/NIX context reads/writes are having NDC cache
misses which inturn might effect performance.
Also changed NDC enums to reflect correct NDC hardware instance.
Signed-off-by: Prakash Brahmajyosyula <bprakash@marvell.com>
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prakash Brahmajyosyula [Thu, 14 Nov 2019 05:26:18 +0000 (10:56 +0530)]
octeontx2-af: Add NIX RQ, SQ and CQ contexts to debugfs
To aid in debugging NIX block related issues, added support to dump
NIX block LF's RQ, SQ and CQ hardware contexts in debugfs. User can
check which contexts are enabled currently and dump it's current HW
context.
Four new files 'qsize', 'rq_ctx', 'sq_ctx' and 'cq_ctx' are added to the
debugfs at 'sys/kernel/debug/octeontx2/nix/'
'echo <nixlf index> > qsize' will display current enabled CQ/SQ/RQs.
'echo <nixlf> [rq number/all] > rq_ctx',
'echo <nixlf> [sq number/all] > sq_ctx' &
'echo <nixlf> [cq number/all] > cq_ctx' will dump RQ/SQ/CQ's current
hardware context.
Signed-off-by: Prakash Brahmajyosyula <bprakash@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christina Jacob [Thu, 14 Nov 2019 05:26:17 +0000 (10:56 +0530)]
octeontx2-af: Add NPA aura and pool contexts to debugfs
To aid in debugging NPA related issues, added support to dump
NPA (pool allocator) block LF's aura and pool hardware contexts in
debugfs. User can check which contexts are enabled currently and dump
it's current HW context.
Three new files 'qsize', 'aura_ctx', 'pool_ctx' are added to the
debugfs at 'sys/kernel/debug/octeontx2/npa/'
'echo <npalf index> > qsize' will display current enabled Aura/Pools.
'echo <npalf> [aura number/all] > aura_ctx' &
'echo <npalf> [aura number/all] > pool_ctx' will dump Aura/Pool
context info.
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Prakash Brahmajyosyula <bprakash@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christina Jacob [Thu, 14 Nov 2019 05:26:16 +0000 (10:56 +0530)]
octeontx2-af: Dump current resource provisioning status
Added support to dump current resource provisioning status
of all resource virtualization unit (RVU) block's
(i.e NPA, NIX, SSO, SSOW, CPT, TIM) local functions attached
to a PF_FUNC into a debugfs file.
'cat /sys/kernel/debug/octeontx2/rsrc_alloc'
will show the current block LF's allocation status.
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Prakash Brahmajyosyula <bprakash@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi [Wed, 13 Nov 2019 23:25:55 +0000 (01:25 +0200)]
net: mvneta: fix build skb for bm capable devices
Fix build_skb for bm capable devices when they fall-back using swbm path
(e.g. when bm properties are configured in device tree but
CONFIG_MVNETA_BM_ENABLE is not set). In this case rx_offset_correction is
overwritten so we need to use it building skb instead of
MVNETA_SKB_HEADROOM directly
Fixes:
8dc9a0888f4c ("net: mvneta: rely on build_skb in mvneta_rx_swbm poll routine")
Fixes:
0db51da7a8e9 ("net: mvneta: add basic XDP support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reported-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 15 Nov 2019 02:01:45 +0000 (18:01 -0800)]
Merge tag 'mlx5-updates-2019-11-12' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-11-12
1) Merge mlx5-next for devlink reload and flowtable offloads dependencies
2) Devlink reload support
3) TC Flowtable offloads
4) Misc cleanup
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 13 Nov 2019 22:03:26 +0000 (23:03 +0100)]
r8169: use r8168d_modify_extpage in rtl8168f_config_eee_phy
Use r8168d_modify_extpage() also in rtl8168f_config_eee_phy() to
simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cris Forno [Wed, 13 Nov 2019 21:06:16 +0000 (15:06 -0600)]
ibmveth: Detect unsupported packets before sending to the hypervisor
Currently, when ibmveth receive a loopback packet, it reports an
ambiguous error message "tx: h_send_logical_lan failed with rc=-4"
because the hypervisor rejects those types of packets. This fix
detects loopback packet and assures the source packet's MAC address
matches the driver's MAC address before transmitting to the
hypervisor.
Signed-off-by: Cris Forno <cforno12@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Murphy [Wed, 13 Nov 2019 16:42:26 +0000 (10:42 -0600)]
net: phy: dp83869: Add TI dp83869 phy
Add support for the TI DP83869 Gigabit ethernet phy
device.
The DP83869 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Murphy [Wed, 13 Nov 2019 16:42:25 +0000 (10:42 -0600)]
dt-bindings: net: dp83869: Add TI dp83869 phy
Add dt bindings for the TI dp83869 Gigabit ethernet phy
device.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tonghao Zhang [Wed, 13 Nov 2019 15:04:49 +0000 (23:04 +0800)]
net: openvswitch: add hash info to upcall
When using the kernel datapath, the upcall don't
include skb hash info relatived. That will introduce
some problem, because the hash of skb is important
in kernel stack. For example, VXLAN module uses
it to select UDP src port. The tx queue selection
may also use the hash in stack.
Hash is computed in different ways. Hash is random
for a TCP socket, and hash may be computed in hardware,
or software stack. Recalculation hash is not easy.
Hash of TCP socket is computed:
tcp_v4_connect
-> sk_set_txhash (is random)
__tcp_transmit_skb
-> skb_set_hash_from_sk
There will be one upcall, without information of skb
hash, to ovs-vswitchd, for the first packet of a TCP
session. The rest packets will be processed in Open vSwitch
modules, hash kept. If this tcp session is forward to
VXLAN module, then the UDP src port of first tcp packet
is different from rest packets.
TCP packets may come from the host or dockers, to Open vSwitch.
To fix it, we store the hash info to upcall, and restore hash
when packets sent back.
+---------------+ +-------------------------+
| Docker/VMs | | ovs-vswitchd |
+----+----------+ +-+--------------------+--+
| ^ |
| | |
| | upcall v restore packet hash (not recalculate)
| +-+--------------------+--+
| tap netdev | | vxlan module
+---------------> +--> Open vSwitch ko +-->
or internal type | |
+-------------------------+
Reported-at: https://mail.openvswitch.org/pipermail/ovs-dev/2019-October/364062.html
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 14 Nov 2019 23:13:28 +0000 (15:13 -0800)]
Merge branch 'Rework-mt762x-GDM-setup-flow'
MarkLee says:
====================
Rework mt762x GDM setup flow
The mt762x GDM block is mainly used to setup the HW internal
rx path from GMAC to RX DMA engine(PDMA) and the packet
switching engine(PSE) is responsed to do the data forward
following the GDM configuration.
This patch set have three goals :
1. Integrate GDM/PSE setup operations into single function "mtk_gdm_config"
2. Refine the timing of GDM/PSE setup, move it from mtk_hw_init
to mtk_open
3. Enable GDM GDMA_DROP_ALL mode to drop all packet during the
stop operation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
MarkLee [Wed, 13 Nov 2019 02:38:44 +0000 (10:38 +0800)]
net: ethernet: mediatek: Enable GDM GDMA_DROP_ALL mode
Enable GDM GDMA_DROP_ALL mode to drop all packet during the
stop operation. This is recommended by the mt762x HW design
to drop all packet from GMAC before stopping PDMA.
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MarkLee [Wed, 13 Nov 2019 02:38:43 +0000 (10:38 +0800)]
net: ethernet: mediatek: Refine the timing of GDM/PSE setup
Refine the timing of GDM/PSE setup, move it from mtk_hw_init
to mtk_open. This is recommended by the mt762x HW design to
do GDM/PSE setup only after PDMA has been started.
We exclude mt7628 in mtk_gdm_config function since it is a old IP
and there is no GDM/PSE block on it.
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MarkLee [Wed, 13 Nov 2019 02:38:42 +0000 (10:38 +0800)]
net: ethernet: mediatek: Integrate GDM/PSE setup operations
Integrate GDM/PSE setup operations into single function "mtk_gdm_config"
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 12 Nov 2019 22:16:41 +0000 (00:16 +0200)]
net: dsa: sja1105: Simplify reset handling
We don't really need 10k species of reset. Remove everything except cold
reset which is what is actually used. Too bad the hardware designers
couldn't agree to use the same bit field for rev 1 and rev 2, so the
(*reset_cmd) function pointer is there to stay.
However let's simplify the prototype and give it a struct dsa_switch (we
want to avoid forward-declarations of structures, in this case struct
sja1105_private, wherever we can).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>