OSDN Git Service
Zhang Qilong [Tue, 27 Oct 2020 13:51:59 +0000 (21:51 +0800)]
net/mac8390: discard unnecessary breaks
The 'break' is unnecessary because of previous 'return',
and we could discard it.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201027135159.71444-1-zhangqilong3@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Łukasz Stelmach [Tue, 27 Oct 2020 11:43:17 +0000 (12:43 +0100)]
net: mii: Report advertised link capabilities when autonegotiation is off
Unify the set of information returned by mii_ethtool_get_link_ksettings(),
mii_ethtool_gset() and phy_ethtool_ksettings_get(). Make the mii_*()
functions report advertised settings when autonegotiation if disabled.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201027114317.8259-1-l.stelmach@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 30 Oct 2020 01:39:49 +0000 (18:39 -0700)]
Merge branch 'net-bridge-cfm-add-support-for-connectivity-fault-management-cfm'
Henrik Bjoernlund says:
====================
net: bridge: cfm: Add support for Connectivity Fault Management(CFM)
Connectivity Fault Management (CFM) is defined in 802.1Q
section 12.14.
Connectivity Fault Management (CFM) comprises capabilities for
detecting, verifying, and isolating connectivity failures in Virtual
Bridged Networks. These capabilities can be used in networks
operated by multiple independent organizations, each with restricted
management access to each other’s equipment.
CFM functions are partitioned as follows:
— Path discovery
— Fault detection
— Fault verification and isolation
— Fault notification
— Fault recovery
The primary CFM protocol shims are called Maintenance Points (MPs).
A MP can be either a MEP or a MHF.
The MEP:
-It is the Maintenance association End Point
described in 802.1Q section 19.2.
-It is created on a specific level (1-7) and is assuring
that no CFM frames are passing through this MEP on lower levels.
-It initiates and terminates/validates CFM frames on its level.
-It can only exist on a port that is related to a bridge.
The MHF:
-It is the Maintenance Domain Intermediate Point
(MIP) Half Function (MHF) described in 802.1Q section 19.3.
-It is created on a specific level (1-7).
-It is extracting/injecting certain CFM frame on this level.
-It can only exist on a port that is related to a bridge.
-Currently not supported.
There are defined the following CFM protocol functions:
-Continuity Check
-Loopback. Currently not supported.
-Linktrace. Currently not supported.
This CFM component supports create/delete of MEP instances and
configuration of the different CFM protocols. Also status information
can be fetched and delivered through notification due to defect
status change.
The user interacts with CFM using the 'cfm' user space client
program, the client talks with the kernel using netlink.
Any notification emitted by CFM from the kernel can be monitored in
user space by starting 'cfm_server' program.
Currently this 'cfm' and 'cfm_server' programs are standalone placed
in a cfm repository https://github.com/microchip-ung/cfm but it is
considered to integrate this into 'iproute2'.
v1 -> v2
Added the CFM switchdev interface and also added utilization by
calling the interface from the kernel CFM implementation trying
to offload CFM functionality to HW. This offload (CFM driver) is
currently not implemented.
Corrections based on RCF comments:
-The single CFM kernel implementation Patch is broken up into
three patches.
-Changed the list of MEP instances from list_head to
hlist_head.
-Removed unnecessary RCU list traversing.
-Solved RCU unlocking problem.
-Removed unnecessary comments.
-Added ASSERT_RTNL() where required.
-Shaping up on error messages.
-Correction NETLINK br_fill_ifinfo() to be able to handle
'filter_mask' with multiple flags asserted.
v2 -> v3
-The switchdev definition and utilization has been removed as
there was no switchdev implementation.
-Some compiling issues are fixed as Reported-by:
kernel test robot <lkp@intel.com>.
v3 -> v4
-Fixed potential crash during hlist walk where elements are
removed.
-Giving all commits unique titles.
-NETLINK implementation split into three commits.
-Commit "bridge: cfm: Bridge port remove" is merged with
commit "bridge: cfm: Kernel space implementation of CFM. MEP
create/delete."
v4 -> v5
-Reordered members in struct net_bridge to bring member
frame_type_list to the first cache line.
-Helper functions nla_get_mac() and nla_get_maid() are removed.
-The NLA_POLICY_NESTED() macro is used to initialize the
br_cfm_policy array.
-Fixed reverse xmas tree.
v5 -> v6
-Fixed that the SKB buffer was not freed during error handling return.
-Removed unused struct definition.
-Changed bool to u8 bitfields for space save.
-Utilizing the NETLINK policy validation feature.
v6 -> v7
-Removed check of parameters in br_cfm_mep_config_set() and
br_cfm_cc_peer_mep_add() in first commit of MEP implementation
(Patch 4 out of 10)
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
====================
Link: https://lore.kernel.org/r/20201027100251.3241719-1-henrik.bjoernlund@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:51 +0000 (10:02 +0000)]
bridge: cfm: Netlink Notifications.
This is the implementation of Netlink notifications out of CFM.
Notifications are initiated whenever a state change happens in CFM.
IFLA_BRIDGE_CFM:
Points to the CFM information.
IFLA_BRIDGE_CFM_MEP_STATUS_INFO:
This indicate that the MEP instance status are following.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO:
This indicate that the peer MEP status are following.
CFM nested attribute has the following attributes in next level.
IFLA_BRIDGE_CFM_MEP_STATUS_INSTANCE:
The MEP instance number of the delivered status.
The type is NLA_U32.
IFLA_BRIDGE_CFM_MEP_STATUS_OPCODE_UNEXP_SEEN:
The MEP instance received CFM PDU with unexpected Opcode.
The type is NLA_U32 (bool).
IFLA_BRIDGE_CFM_MEP_STATUS_VERSION_UNEXP_SEEN:
The MEP instance received CFM PDU with unexpected version.
The type is NLA_U32 (bool).
IFLA_BRIDGE_CFM_MEP_STATUS_RX_LEVEL_LOW_SEEN:
The MEP instance received CCM PDU with MD level lower than
configured level. This frame is discarded.
The type is NLA_U32 (bool).
IFLA_BRIDGE_CFM_CC_PEER_STATUS_INSTANCE:
The MEP instance number of the delivered status.
The type is NLA_U32.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_PEER_MEPID:
The added Peer MEP ID of the delivered status.
The type is NLA_U32.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_CCM_DEFECT:
The CCM defect status.
The type is NLA_U32 (bool).
True means no CCM frame is received for 3.25 intervals.
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_RDI:
The last received CCM PDU RDI.
The type is NLA_U32 (bool).
IFLA_BRIDGE_CFM_CC_PEER_STATUS_PORT_TLV_VALUE:
The last received CCM PDU Port Status TLV value field.
The type is NLA_U8.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_IF_TLV_VALUE:
The last received CCM PDU Interface Status TLV value field.
The type is NLA_U8.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEEN:
A CCM frame has been received from Peer MEP.
The type is NLA_U32 (bool).
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_TLV_SEEN:
A CCM frame with TLV has been received from Peer MEP.
The type is NLA_U32 (bool).
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEQ_UNEXP_SEEN:
A CCM frame with unexpected sequence number has been received
from Peer MEP.
The type is NLA_U32 (bool).
When a sequence number is not one higher than previously received
then it is unexpected.
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:50 +0000 (10:02 +0000)]
bridge: cfm: Netlink GET status Interface.
This is the implementation of CFM netlink status
get information interface.
Add new nested netlink attributes. These attributes are used by the
user space to get status information.
GETLINK:
Request filter RTEXT_FILTER_CFM_STATUS:
Indicating that CFM status information must be delivered.
IFLA_BRIDGE_CFM:
Points to the CFM information.
IFLA_BRIDGE_CFM_MEP_STATUS_INFO:
This indicate that the MEP instance status are following.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO:
This indicate that the peer MEP status are following.
CFM nested attribute has the following attributes in next level.
GETLINK RTEXT_FILTER_CFM_STATUS:
IFLA_BRIDGE_CFM_MEP_STATUS_INSTANCE:
The MEP instance number of the delivered status.
The type is u32.
IFLA_BRIDGE_CFM_MEP_STATUS_OPCODE_UNEXP_SEEN:
The MEP instance received CFM PDU with unexpected Opcode.
The type is u32 (bool).
IFLA_BRIDGE_CFM_MEP_STATUS_VERSION_UNEXP_SEEN:
The MEP instance received CFM PDU with unexpected version.
The type is u32 (bool).
IFLA_BRIDGE_CFM_MEP_STATUS_RX_LEVEL_LOW_SEEN:
The MEP instance received CCM PDU with MD level lower than
configured level. This frame is discarded.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_PEER_STATUS_INSTANCE:
The MEP instance number of the delivered status.
The type is u32.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_PEER_MEPID:
The added Peer MEP ID of the delivered status.
The type is u32.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_CCM_DEFECT:
The CCM defect status.
The type is u32 (bool).
True means no CCM frame is received for 3.25 intervals.
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_RDI:
The last received CCM PDU RDI.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_PEER_STATUS_PORT_TLV_VALUE:
The last received CCM PDU Port Status TLV value field.
The type is u8.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_IF_TLV_VALUE:
The last received CCM PDU Interface Status TLV value field.
The type is u8.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEEN:
A CCM frame has been received from Peer MEP.
The type is u32 (bool).
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_TLV_SEEN:
A CCM frame with TLV has been received from Peer MEP.
The type is u32 (bool).
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEQ_UNEXP_SEEN:
A CCM frame with unexpected sequence number has been received
from Peer MEP.
The type is u32 (bool).
When a sequence number is not one higher than previously received
then it is unexpected.
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:49 +0000 (10:02 +0000)]
bridge: cfm: Netlink GET configuration Interface.
This is the implementation of CFM netlink configuration
get information interface.
Add new nested netlink attributes. These attributes are used by the
user space to get configuration information.
GETLINK:
Request filter RTEXT_FILTER_CFM_CONFIG:
Indicating that CFM configuration information must be delivered.
IFLA_BRIDGE_CFM:
Points to the CFM information.
IFLA_BRIDGE_CFM_MEP_CREATE_INFO:
This indicate that MEP instance create parameters are following.
IFLA_BRIDGE_CFM_MEP_CONFIG_INFO:
This indicate that MEP instance config parameters are following.
IFLA_BRIDGE_CFM_CC_CONFIG_INFO:
This indicate that MEP instance CC functionality
parameters are following.
IFLA_BRIDGE_CFM_CC_RDI_INFO:
This indicate that CC transmitted CCM PDU RDI
parameters are following.
IFLA_BRIDGE_CFM_CC_CCM_TX_INFO:
This indicate that CC transmitted CCM PDU parameters are
following.
IFLA_BRIDGE_CFM_CC_PEER_MEP_INFO:
This indicate that the added peer MEP IDs are following.
CFM nested attribute has the following attributes in next level.
GETLINK RTEXT_FILTER_CFM_CONFIG:
IFLA_BRIDGE_CFM_MEP_CREATE_INSTANCE:
The created MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CREATE_DOMAIN:
The created MEP domain.
The type is u32 (br_cfm_domain).
It must be BR_CFM_PORT.
This means that CFM frames are transmitted and received
directly on the port - untagged. Not in a VLAN.
IFLA_BRIDGE_CFM_MEP_CREATE_DIRECTION:
The created MEP direction.
The type is u32 (br_cfm_mep_direction).
It must be BR_CFM_MEP_DIRECTION_DOWN.
This means that CFM frames are transmitted and received on
the port. Not in the bridge.
IFLA_BRIDGE_CFM_MEP_CREATE_IFINDEX:
The created MEP residence port ifindex.
The type is u32 (ifindex).
IFLA_BRIDGE_CFM_MEP_DELETE_INSTANCE:
The deleted MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CONFIG_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CONFIG_UNICAST_MAC:
The configured MEP unicast MAC address.
The type is 6*u8 (array).
This is used as SMAC in all transmitted CFM frames.
IFLA_BRIDGE_CFM_MEP_CONFIG_MDLEVEL:
The configured MEP unicast MD level.
The type is u32.
It must be in the range 1-7.
No CFM frames are passing through this MEP on lower levels.
IFLA_BRIDGE_CFM_MEP_CONFIG_MEPID:
The configured MEP ID.
The type is u32.
It must be in the range 0-0x1FFF.
This MEP ID is inserted in any transmitted CCM frame.
IFLA_BRIDGE_CFM_CC_CONFIG_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_CONFIG_ENABLE:
The Continuity Check (CC) functionality is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL:
The CC expected receive interval of CCM frames.
The type is u32 (br_cfm_ccm_interval).
This is also the transmission interval of CCM frames when enabled.
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_MAID:
The CC expected receive MAID in CCM frames.
The type is CFM_MAID_LENGTH*u8.
This is MAID is also inserted in transmitted CCM frames.
IFLA_BRIDGE_CFM_CC_PEER_MEP_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_PEER_MEPID:
The CC Peer MEP ID added.
The type is u32.
When a Peer MEP ID is added and CC is enabled it is expected to
receive CCM frames from that Peer MEP.
IFLA_BRIDGE_CFM_CC_RDI_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_RDI_RDI:
The RDI that is inserted in transmitted CCM PDU.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_CCM_TX_DMAC:
The transmitted CCM frame destination MAC address.
The type is 6*u8 (array).
This is used as DMAC in all transmitted CFM frames.
IFLA_BRIDGE_CFM_CC_CCM_TX_SEQ_NO_UPDATE:
The transmitted CCM frame update (increment) of sequence
number is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_PERIOD:
The period of time where CCM frame are transmitted.
The type is u32.
The time is given in seconds. SETLINK IFLA_BRIDGE_CFM_CC_CCM_TX
must be done before timeout to keep transmission alive.
When period is zero any ongoing CCM frame transmission
will be stopped.
IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV:
The transmitted CCM frame update with Interface Status TLV
is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV_VALUE:
The transmitted Interface Status TLV value field.
The type is u8.
IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV:
The transmitted CCM frame update with Port Status TLV is enabled
or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV_VALUE:
The transmitted Port Status TLV value field.
The type is u8.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:48 +0000 (10:02 +0000)]
bridge: cfm: Netlink SET configuration Interface.
This is the implementation of CFM netlink configuration
set information interface.
Add new nested netlink attributes. These attributes are used by the
user space to create/delete/configure CFM instances.
SETLINK:
IFLA_BRIDGE_CFM:
Indicate that the following attributes are CFM.
IFLA_BRIDGE_CFM_MEP_CREATE:
This indicate that a MEP instance must be created.
IFLA_BRIDGE_CFM_MEP_DELETE:
This indicate that a MEP instance must be deleted.
IFLA_BRIDGE_CFM_MEP_CONFIG:
This indicate that a MEP instance must be configured.
IFLA_BRIDGE_CFM_CC_CONFIG:
This indicate that a MEP instance Continuity Check (CC)
functionality must be configured.
IFLA_BRIDGE_CFM_CC_PEER_MEP_ADD:
This indicate that a CC Peer MEP must be added.
IFLA_BRIDGE_CFM_CC_PEER_MEP_REMOVE:
This indicate that a CC Peer MEP must be removed.
IFLA_BRIDGE_CFM_CC_CCM_TX:
This indicate that the CC transmitted CCM PDU must be configured.
IFLA_BRIDGE_CFM_CC_RDI:
This indicate that the CC transmitted CCM PDU RDI must be
configured.
CFM nested attribute has the following attributes in next level.
SETLINK RTEXT_FILTER_CFM_CONFIG:
IFLA_BRIDGE_CFM_MEP_CREATE_INSTANCE:
The created MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CREATE_DOMAIN:
The created MEP domain.
The type is u32 (br_cfm_domain).
It must be BR_CFM_PORT.
This means that CFM frames are transmitted and received
directly on the port - untagged. Not in a VLAN.
IFLA_BRIDGE_CFM_MEP_CREATE_DIRECTION:
The created MEP direction.
The type is u32 (br_cfm_mep_direction).
It must be BR_CFM_MEP_DIRECTION_DOWN.
This means that CFM frames are transmitted and received on
the port. Not in the bridge.
IFLA_BRIDGE_CFM_MEP_CREATE_IFINDEX:
The created MEP residence port ifindex.
The type is u32 (ifindex).
IFLA_BRIDGE_CFM_MEP_DELETE_INSTANCE:
The deleted MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CONFIG_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CONFIG_UNICAST_MAC:
The configured MEP unicast MAC address.
The type is 6*u8 (array).
This is used as SMAC in all transmitted CFM frames.
IFLA_BRIDGE_CFM_MEP_CONFIG_MDLEVEL:
The configured MEP unicast MD level.
The type is u32.
It must be in the range 1-7.
No CFM frames are passing through this MEP on lower levels.
IFLA_BRIDGE_CFM_MEP_CONFIG_MEPID:
The configured MEP ID.
The type is u32.
It must be in the range 0-0x1FFF.
This MEP ID is inserted in any transmitted CCM frame.
IFLA_BRIDGE_CFM_CC_CONFIG_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_CONFIG_ENABLE:
The Continuity Check (CC) functionality is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL:
The CC expected receive interval of CCM frames.
The type is u32 (br_cfm_ccm_interval).
This is also the transmission interval of CCM frames when enabled.
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_MAID:
The CC expected receive MAID in CCM frames.
The type is CFM_MAID_LENGTH*u8.
This is MAID is also inserted in transmitted CCM frames.
IFLA_BRIDGE_CFM_CC_PEER_MEP_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_PEER_MEPID:
The CC Peer MEP ID added.
The type is u32.
When a Peer MEP ID is added and CC is enabled it is expected to
receive CCM frames from that Peer MEP.
IFLA_BRIDGE_CFM_CC_RDI_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_RDI_RDI:
The RDI that is inserted in transmitted CCM PDU.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_CCM_TX_DMAC:
The transmitted CCM frame destination MAC address.
The type is 6*u8 (array).
This is used as DMAC in all transmitted CFM frames.
IFLA_BRIDGE_CFM_CC_CCM_TX_SEQ_NO_UPDATE:
The transmitted CCM frame update (increment) of sequence
number is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_PERIOD:
The period of time where CCM frame are transmitted.
The type is u32.
The time is given in seconds. SETLINK IFLA_BRIDGE_CFM_CC_CCM_TX
must be done before timeout to keep transmission alive.
When period is zero any ongoing CCM frame transmission
will be stopped.
IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV:
The transmitted CCM frame update with Interface Status TLV
is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV_VALUE:
The transmitted Interface Status TLV value field.
The type is u8.
IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV:
The transmitted CCM frame update with Port Status TLV is enabled
or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV_VALUE:
The transmitted Port Status TLV value field.
The type is u8.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:47 +0000 (10:02 +0000)]
bridge: cfm: Kernel space implementation of CFM. CCM frame RX added.
This is the third commit of the implementation of the CFM protocol
according to 802.1Q section 12.14.
Functionality is extended with CCM frame reception.
The MEP instance now contains CCM based status information.
Most important is the CCM defect status indicating if correct
CCM frames are received with the expected interval.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:46 +0000 (10:02 +0000)]
bridge: cfm: Kernel space implementation of CFM. CCM frame TX added.
This is the second commit of the implementation of the CFM protocol
according to 802.1Q section 12.14.
Functionality is extended with CCM frame transmission.
Interface is extended with these functions:
br_cfm_cc_rdi_set()
br_cfm_cc_ccm_tx()
br_cfm_cc_config_set()
A MEP Continuity Check feature can be configured by
br_cfm_cc_config_set()
The Continuity Check parameters can be configured to be used when
transmitting CCM.
A MEP can be configured to start or stop transmission of CCM frames by
br_cfm_cc_ccm_tx()
The CCM will be transmitted for a selected period in seconds.
Must call this function before timeout to keep transmission alive.
A MEP transmitting CCM can be configured with inserted RDI in PDU by
br_cfm_cc_rdi_set()
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:45 +0000 (10:02 +0000)]
bridge: cfm: Kernel space implementation of CFM. MEP create/delete.
This is the first commit of the implementation of the CFM protocol
according to 802.1Q section 12.14.
It contains MEP instance create, delete and configuration.
Connectivity Fault Management (CFM) comprises capabilities for
detecting, verifying, and isolating connectivity failures in
Virtual Bridged Networks. These capabilities can be used in
networks operated by multiple independent organizations, each
with restricted management access to each others equipment.
CFM functions are partitioned as follows:
- Path discovery
- Fault detection
- Fault verification and isolation
- Fault notification
- Fault recovery
Interface consists of these functions:
br_cfm_mep_create()
br_cfm_mep_delete()
br_cfm_mep_config_set()
br_cfm_cc_config_set()
br_cfm_cc_peer_mep_add()
br_cfm_cc_peer_mep_remove()
A MEP instance is created by br_cfm_mep_create()
-It is the Maintenance association End Point
described in 802.1Q section 19.2.
-It is created on a specific level (1-7) and is assuring
that no CFM frames are passing through this MEP on lower levels.
-It initiates and validates CFM frames on its level.
-It can only exist on a port that is related to a bridge.
-Attributes given cannot be changed until the instance is
deleted.
A MEP instance can be deleted by br_cfm_mep_delete().
A created MEP instance has attributes that can be
configured by br_cfm_mep_config_set().
A MEP Continuity Check feature can be configured by
br_cfm_cc_config_set()
The Continuity Check Receiver state machine can be
enabled and disabled.
According to 802.1Q section 19.2.8
A MEP can have Peer MEPs added and removed by
br_cfm_cc_peer_mep_add() and br_cfm_cc_peer_mep_remove()
The Continuity Check feature can maintain connectivity
status on each added Peer MEP.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:44 +0000 (10:02 +0000)]
bridge: uapi: cfm: Added EtherType used by the CFM protocol.
This EtherType is used by all CFM protocal frames transmitted
according to 802.1Q section 12.14.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:43 +0000 (10:02 +0000)]
bridge: cfm: Add BRIDGE_CFM to Kconfig.
This makes it possible to include or exclude the CFM
protocol according to 802.1Q section 12.14.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:42 +0000 (10:02 +0000)]
net: bridge: extend the process of special frames
This patch extends the processing of frames in the bridge. Currently MRP
frames needs special processing and the current implementation doesn't
allow a nice way to process different frame types. Therefore try to
improve this by adding a list that contains frame types that need
special processing. This list is iterated for each input frame and if
there is a match based on frame type then these functions will be called
and decide what to do with the frame. It can process the frame then the
bridge doesn't need to do anything or don't process so then the bridge
will do normal forwarding.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 30 Oct 2020 00:43:23 +0000 (17:43 -0700)]
Merge branch 'vsock-minor-clean-up-of-ioctl-error-handling'
Colin Ian King says:
====================
vsock: minor clean up of ioctl error handling
Two minor changes to the ioctl error handling.
====================
Link: https://lore.kernel.org/r/20201027090942.14916-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Colin Ian King [Tue, 27 Oct 2020 09:09:42 +0000 (09:09 +0000)]
vsock: fix the error return when an invalid ioctl command is used
Currently when an invalid ioctl command is used the error return
is -EINVAL. Fix this by returning the correct error -ENOIOCTLCMD.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Colin Ian King [Tue, 27 Oct 2020 09:09:41 +0000 (09:09 +0000)]
vsock: remove ratelimit unknown ioctl message
When exercising the kernel with stress-ng with some ioctl tests the
"Unknown ioctl" error message is spamming the kernel log at a high
rate. Remove this message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 29 Oct 2020 21:08:40 +0000 (14:08 -0700)]
Merge git://git./linux/kernel/git/netdev/net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 29 Oct 2020 20:02:52 +0000 (13:02 -0700)]
Merge tag 'fallthrough-fixes-clang-5.10-rc2' of git://git./linux/kernel/git/gustavoars/linux
Pull fallthrough fix from Gustavo A. R. Silva:
"This fixes a ton of fall-through warnings when building with Clang
12.0.0 and -Wimplicit-fallthrough"
* tag 'fallthrough-fixes-clang-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
include: jhash/signal: Fix fall-through warnings for Clang
Linus Torvalds [Thu, 29 Oct 2020 19:55:02 +0000 (12:55 -0700)]
Merge tag 'net-5.10-rc2' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Current release regressions:
- r8169: fix forced threading conflicting with other shared
interrupts; we tried to fix the use of raise_softirq_irqoff from an
IRQ handler on RT by forcing hard irqs, but this driver shares
legacy PCI IRQs so drop the _irqoff() instead
- tipc: fix memory leak caused by a recent syzbot report fix to
tipc_buf_append()
Current release - bugs in new features:
- devlink: Unlock on error in dumpit() and fix some error codes
- net/smc: fix null pointer dereference in smc_listen_decline()
Previous release - regressions:
- tcp: Prevent low rmem stalls with SO_RCVLOWAT.
- net: protect tcf_block_unbind with block lock
- ibmveth: Fix use of ibmveth in a bridge; the self-imposed filtering
to only send legal frames to the hypervisor was too strict
- net: hns3: Clear the CMDQ registers before unmapping BAR region;
incorrect cleanup order was leading to a crash
- bnxt_en - handful of fixes to fixes:
- Send HWRM_FUNC_RESET fw command unconditionally, even if there
are PCIe errors being reported
- Check abort error state in bnxt_open_nic().
- Invoke cancel_delayed_work_sync() for PFs also.
- Fix regression in workqueue cleanup logic in bnxt_remove_one().
- mlxsw: Only advertise link modes supported by both driver and
device, after removal of 56G support from the driver 56G was not
cleared from advertised modes
- net/smc: fix suppressed return code
Previous release - always broken:
- netem: fix zero division in tabledist, caused by integer overflow
- bnxt_en: Re-write PCI BARs after PCI fatal error.
- cxgb4: set up filter action after rewrites
- net: ipa: command payloads already mapped
Misc:
- s390/ism: fix incorrect system EID, it's okay to change since it
was added in current release
- vsock: use ns_capable_noaudit() on socket create to suppress false
positive audit messages"
* tag 'net-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (36 commits)
r8169: fix issue with forced threading in combination with shared interrupts
netem: fix zero division in tabledist
ibmvnic: fix ibmvnic_set_mac
mptcp: add missing memory scheduling in the rx path
tipc: fix memory leak caused by tipc_buf_append()
gtp: fix an use-before-init in gtp_newlink()
net: protect tcf_block_unbind with block lock
ibmveth: Fix use of ibmveth in a bridge.
net/sched: act_mpls: Add softdep on mpls_gso.ko
ravb: Fix bit fields checking in ravb_hwtstamp_get()
devlink: Unlock on error in dumpit()
devlink: Fix some error codes
chelsio/chtls: fix memory leaks in CPL handlers
chelsio/chtls: fix deadlock issue
net: hns3: Clear the CMDQ registers before unmapping BAR region
bnxt_en: Send HWRM_FUNC_RESET fw command unconditionally.
bnxt_en: Check abort error state in bnxt_open_nic().
bnxt_en: Re-write PCI BARs after PCI fatal error.
bnxt_en: Invoke cancel_delayed_work_sync() for PFs also.
bnxt_en: Fix regression in workqueue cleanup logic in bnxt_remove_one().
...
Linus Torvalds [Thu, 29 Oct 2020 18:50:59 +0000 (11:50 -0700)]
Merge tag 'for-linus' of git://git./linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"The good news is people are testing rc1 in the RDMA world - the bad
news is testing of the for-next area is not as good as I had hoped, as
we really should have caught at least the rdma_connect_locked() issue
before now.
Notable merge window regressions that didn't get caught/fixed in time
for rc1:
- Fix in kernel users of rxe, they were broken by the rapid fix to
undo the uABI breakage in rxe from another patch
- EFA userspace needs to read the GID table but was broken with the
new GID table logic
- Fix user triggerable deadlock in mlx5 using devlink reload
- Fix deadlock in several ULPs using rdma_connect from the CM handler
callbacks
- Memory leak in qedr"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/qedr: Fix memory leak in iWARP CM
RDMA: Add rdma_connect_locked()
RDMA/uverbs: Fix false error in query gid IOCTL
RDMA/mlx5: Fix devlink deadlock on net namespace deletion
RDMA/rxe: Fix small problem in network_type patch
Heiner Kallweit [Thu, 29 Oct 2020 09:18:53 +0000 (10:18 +0100)]
r8169: fix issue with forced threading in combination with shared interrupts
As reported by Serge flag IRQF_NO_THREAD causes an error if the
interrupt is actually shared and the other driver(s) don't have this
flag set. This situation can occur if a PCI(e) legacy interrupt is
used in combination with forced threading.
There's no good way to deal with this properly, therefore we have to
remove flag IRQF_NO_THREAD. For fixing the original forced threading
issue switch to napi_schedule().
Fixes:
424a646e072a ("r8169: fix operation under forced interrupt threading")
Link: https://www.spinics.net/lists/netdev/msg694960.html
Reported-by: Serge Belyshev <belyshev@depni.sinp.msu.ru>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Serge Belyshev <belyshev@depni.sinp.msu.ru>
Link: https://lore.kernel.org/r/b5b53bfe-35ac-3768-85bf-74d1290cf394@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Aleksandr Nogikh [Wed, 28 Oct 2020 17:07:31 +0000 (17:07 +0000)]
netem: fix zero division in tabledist
Currently it is possible to craft a special netlink RTM_NEWQDISC
command that can result in jitter being equal to 0x80000000. It is
enough to set the 32 bit jitter to 0x02000000 (it will later be
multiplied by 2^6) or just set the 64 bit jitter via
TCA_NETEM_JITTER64. This causes an overflow during the generation of
uniformly distributed numbers in tabledist(), which in turn leads to
division by zero (sigma != 0, but sigma * 2 is 0).
The related fragment of code needs 32-bit division - see commit
9b0ed89 ("netem: remove unnecessary 64 bit modulus"), so switching to
64 bit is not an option.
Fix the issue by keeping the value of jitter within the range that can
be adequately handled by tabledist() - [0;INT_MAX]. As negative std
deviation makes no sense, take the absolute value of the passed value
and cap it at INT_MAX. Inside tabledist(), switch to unsigned 32 bit
arithmetic in order to prevent overflows.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Aleksandr Nogikh <nogikh@google.com>
Reported-by: syzbot+ec762a6342ad0d3c0d8f@syzkaller.appspotmail.com
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Link: https://lore.kernel.org/r/20201028170731.1383332-1-aleksandrnogikh@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lijun Pan [Tue, 27 Oct 2020 22:04:56 +0000 (17:04 -0500)]
ibmvnic: fix ibmvnic_set_mac
Jakub Kicinski brought up a concern in ibmvnic_set_mac().
ibmvnic_set_mac() does this:
ether_addr_copy(adapter->mac_addr, addr->sa_data);
if (adapter->state != VNIC_PROBED)
rc = __ibmvnic_set_mac(netdev, addr->sa_data);
So if state == VNIC_PROBED, the user can assign an invalid address to
adapter->mac_addr, and ibmvnic_set_mac() will still return 0.
The fix is to validate ethernet address at the beginning of
ibmvnic_set_mac(), and move the ether_addr_copy to
the case of "adapter->state != VNIC_PROBED".
Fixes:
c26eba03e407 ("ibmvnic: Update reset infrastructure to support tunable parameters")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201027220456.71450-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paolo Abeni [Tue, 27 Oct 2020 14:59:14 +0000 (15:59 +0100)]
mptcp: add missing memory scheduling in the rx path
When moving the skbs from the subflow into the msk receive
queue, we must schedule there the required amount of memory.
Try to borrow the required memory from the subflow, if needed,
so that we leverage the existing TCP heuristic.
Fixes:
6771bfd9ee24 ("mptcp: update mptcp ack sequence from work queue")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Link: https://lore.kernel.org/r/f6143a6193a083574f11b00dbf7b5ad151bc4ff4.1603810630.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gustavo A. R. Silva [Thu, 3 Sep 2020 04:25:55 +0000 (23:25 -0500)]
include: jhash/signal: Fix fall-through warnings for Clang
In preparation to enable -Wimplicit-fallthrough for Clang, explicitly
add break statements instead of letting the code fall through to the
next case.
This patch adds four break statements that, together, fix almost 40,000
warnings when building Linux 5.10-rc1 with Clang 12.0.0 and this[1] change
reverted. Notice that in order to enable -Wimplicit-fallthrough for Clang,
such change[1] is meant to be reverted at some point. So, this patch helps
to move in that direction.
Something important to mention is that there is currently a discrepancy
between GCC and Clang when dealing with switch fall-through to empty case
statements or to cases that only contain a break/continue/return
statement[2][3][4].
Now that the -Wimplicit-fallthrough option has been globally enabled[5],
any compiler should really warn on missing either a fallthrough annotation
or any of the other case-terminating statements (break/continue/return/
goto) when falling through to the next case statement. Making exceptions
to this introduces variation in case handling which may continue to lead
to bugs, misunderstandings, and a general lack of robustness. The point
of enabling options like -Wimplicit-fallthrough is to prevent human error
and aid developers in spotting bugs before their code is even built/
submitted/committed, therefore eliminating classes of bugs. So, in order
to really accomplish this, we should, and can, move in the direction of
addressing any error-prone scenarios and get rid of the unintentional
fallthrough bug-class in the kernel, entirely, even if there is some minor
redundancy. Better to have explicit case-ending statements than continue to
have exceptions where one must guess as to the right result. The compiler
will eliminate any actual redundancy.
[1] commit
e2079e93f562c ("kbuild: Do not enable -Wimplicit-fallthrough for clang for now")
[2] https://github.com/ClangBuiltLinux/linux/issues/636
[3] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=91432
[4] https://godbolt.org/z/xgkvIh
[5] commit
a035d552a93b ("Makefile: Globally enable fall-through warning")
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Linus Torvalds [Thu, 29 Oct 2020 17:13:09 +0000 (10:13 -0700)]
Merge tag 'afs-fixes-
20201029' of git://git./linux/kernel/git/dhowells/linux-fs
Pull AFS fixes from David Howells:
- Fix copy_file_range() to an afs file now returning EINVAL if the
splice_write file op isn't supplied.
- Fix a deref-before-check in afs_unuse_cell().
- Fix a use-after-free in afs_xattr_get_acl().
- Fix afs to not try to clear PG_writeback when laundering a page.
- Fix afs to take a ref on a page that it sets PG_private on and to
drop that ref when clearing PG_private. This is done through recently
added helpers.
- Fix a page leak if write_begin() fails.
- Fix afs_write_begin() to not alter the dirty region info stored in
page->private, but rather do this in afs_write_end() instead when we
know what we actually changed.
- Fix afs_invalidatepage() to alter the dirty region info on a page
when partial page invalidation occurs so that we don't inadvertantly
include a span of zeros that will get written back if a page gets
laundered due to a remote 3rd-party induced invalidation.
We mustn't, however, reduce the dirty region if the page has been
seen to be mapped (ie. we got called through the page_mkwrite vector)
as the page might still be mapped and we might lose data if the file
is extended again.
- Fix the dirty region info to have a lower resolution if the size of
the page is too large for this to be encoded (e.g. powerpc32 with 64K
pages).
Note that this might not be the ideal way to handle this, since it
may allow some leakage of undirtied zero bytes to the server's copy
in the case of a 3rd-party conflict.
To aid the last two fixes, two additional changes:
- Wrap the manipulations of the dirty region info stored in
page->private into helper functions.
- Alter the encoding of the dirty region so that the region bounds can
be stored with one fewer bit, making a bit available for the
indication of mappedness.
* tag 'afs-fixes-
20201029' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Fix dirty-region encoding on ppc32 with 64K pages
afs: Fix afs_invalidatepage to adjust the dirty region
afs: Alter dirty range encoding in page->private
afs: Wrap page->private manipulations in inline functions
afs: Fix where page->private is set during write
afs: Fix page leak on afs_write_begin() failure
afs: Fix to take ref on page when PG_private is set
afs: Fix afs_launder_page to not clear PG_writeback
afs: Fix a use after free in afs_xattr_get_acl()
afs: Fix tracing deref-before-check
afs: Fix copy_file_range()
Tung Nguyen [Tue, 27 Oct 2020 03:24:03 +0000 (10:24 +0700)]
tipc: fix memory leak caused by tipc_buf_append()
Commit
ed42989eab57 ("tipc: fix the skb_unshare() in tipc_buf_append()")
replaced skb_unshare() with skb_copy() to not reduce the data reference
counter of the original skb intentionally. This is not the correct
way to handle the cloned skb because it causes memory leak in 2
following cases:
1/ Sending multicast messages via broadcast link
The original skb list is cloned to the local skb list for local
destination. After that, the data reference counter of each skb
in the original list has the value of 2. This causes each skb not
to be freed after receiving ACK:
tipc_link_advance_transmq()
{
...
/* release skb */
__skb_unlink(skb, &l->transmq);
kfree_skb(skb); <-- memory exists after being freed
}
2/ Sending multicast messages via replicast link
Similar to the above case, each skb cannot be freed after purging
the skb list:
tipc_mcast_xmit()
{
...
__skb_queue_purge(pkts); <-- memory exists after being freed
}
This commit fixes this issue by using skb_unshare() instead. Besides,
to avoid use-after-free error reported by KASAN, the pointer to the
fragment is set to NULL before calling skb_unshare() to make sure that
the original skb is not freed after freeing the fragment 2 times in
case skb_unshare() returns NULL.
Fixes:
ed42989eab57 ("tipc: fix the skb_unshare() in tipc_buf_append()")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Reported-by: Thang Hoang Ngo <thang.h.ngo@dektech.com.au>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://lore.kernel.org/r/20201027032403.1823-1-tung.q.nguyen@dektech.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Masahiro Fujiwara [Tue, 27 Oct 2020 11:48:46 +0000 (20:48 +0900)]
gtp: fix an use-before-init in gtp_newlink()
*_pdp_find() from gtp_encap_recv() would trigger a crash when a peer
sends GTP packets while creating new GTP device.
RIP: 0010:gtp1_pdp_find.isra.0+0x68/0x90 [gtp]
<SNIP>
Call Trace:
<IRQ>
gtp_encap_recv+0xc2/0x2e0 [gtp]
? gtp1_pdp_find.isra.0+0x90/0x90 [gtp]
udp_queue_rcv_one_skb+0x1fe/0x530
udp_queue_rcv_skb+0x40/0x1b0
udp_unicast_rcv_skb.isra.0+0x78/0x90
__udp4_lib_rcv+0x5af/0xc70
udp_rcv+0x1a/0x20
ip_protocol_deliver_rcu+0xc5/0x1b0
ip_local_deliver_finish+0x48/0x50
ip_local_deliver+0xe5/0xf0
? ip_protocol_deliver_rcu+0x1b0/0x1b0
gtp_encap_enable() should be called after gtp_hastable_new() otherwise
*_pdp_find() will access the uninitialized hash table.
Fixes:
1e3a3abd8b28 ("gtp: make GTP sockets in gtp_newlink optional")
Signed-off-by: Masahiro Fujiwara <fujiwara.masahiro@gmail.com>
Link: https://lore.kernel.org/r/20201027114846.3924-1-fujiwara.masahiro@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 29 Oct 2020 16:36:11 +0000 (09:36 -0700)]
Merge tag 'ext4_for_linus_fixes' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Bug fixes for the new ext4 fast commit feature, plus a fix for the
'data=journal' bug fix.
Also use the generic casefolding support which has now landed in
fs/libfs.c for 5.10"
* tag 'ext4_for_linus_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: indicate that fast_commit is available via /sys/fs/ext4/feature/...
ext4: use generic casefolding support
ext4: do not use extent after put_bh
ext4: use IS_ERR() for error checking of path
ext4: fix mmap write protection for data=journal mode
jbd2: fix a kernel-doc markup
ext4: use s_mount_flags instead of s_mount_state for fast commit state
ext4: make num of fast commit blocks configurable
ext4: properly check for dirty state in ext4_inode_datasync_dirty()
ext4: fix double locking in ext4_fc_commit_dentry_updates()
David Howells [Wed, 28 Oct 2020 12:08:39 +0000 (12:08 +0000)]
afs: Fix dirty-region encoding on ppc32 with 64K pages
The dirty region bounds stored in page->private on an afs page are 15 bits
on a 32-bit box and can, at most, represent a range of up to 32K within a
32K page with a resolution of 1 byte. This is a problem for powerpc32 with
64K pages enabled.
Further, transparent huge pages may get up to 2M, which will be a problem
for the afs filesystem on all 32-bit arches in the future.
Fix this by decreasing the resolution. For the moment, a 64K page will
have a resolution determined from PAGE_SIZE. In the future, the page will
need to be passed in to the helper functions so that the page size can be
assessed and the resolution determined dynamically.
Note that this might not be the ideal way to handle this, since it may
allow some leakage of undirtied zero bytes to the server's copy in the case
of a 3rd-party conflict. Fixing that would require a separately allocated
record and is a more complicated fix.
Fixes:
4343d00872e1 ("afs: Get rid of the afs_writeback record")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
David Howells [Thu, 22 Oct 2020 13:08:23 +0000 (14:08 +0100)]
afs: Fix afs_invalidatepage to adjust the dirty region
Fix afs_invalidatepage() to adjust the dirty region recorded in
page->private when truncating a page. If the dirty region is entirely
removed, then the private data is cleared and the page dirty state is
cleared.
Without this, if the page is truncated and then expanded again by truncate,
zeros from the expanded, but no-longer dirty region may get written back to
the server if the page gets laundered due to a conflicting 3rd-party write.
It mustn't, however, shorten the dirty region of the page if that page is
still mmapped and has been marked dirty by afs_page_mkwrite(), so a flag is
stored in page->private to record this.
Fixes:
4343d00872e1 ("afs: Get rid of the afs_writeback record")
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 26 Oct 2020 13:57:44 +0000 (13:57 +0000)]
afs: Alter dirty range encoding in page->private
Currently, page->private on an afs page is used to store the range of
dirtied data within the page, where the range includes the lower bound, but
excludes the upper bound (e.g. 0-1 is a range covering a single byte).
This, however, requires a superfluous bit for the last-byte bound so that
on a 4KiB page, it can say 0-4096 to indicate the whole page, the idea
being that having both numbers the same would indicate an empty range.
This is unnecessary as the PG_private bit is clear if it's an empty range
(as is PG_dirty).
Alter the way the dirty range is encoded in page->private such that the
upper bound is reduced by 1 (e.g. 0-0 is then specified the same single
byte range mentioned above).
Applying this to both bounds frees up two bits, one of which can be used in
a future commit.
This allows the afs filesystem to be compiled on ppc32 with 64K pages;
without this, the following warnings are seen:
../fs/afs/internal.h: In function 'afs_page_dirty_to':
../fs/afs/internal.h:881:15: warning: right shift count >= width of type [-Wshift-count-overflow]
881 | return (priv >> __AFS_PAGE_PRIV_SHIFT) & __AFS_PAGE_PRIV_MASK;
| ^~
../fs/afs/internal.h: In function 'afs_page_dirty':
../fs/afs/internal.h:886:28: warning: left shift count >= width of type [-Wshift-count-overflow]
886 | return ((unsigned long)to << __AFS_PAGE_PRIV_SHIFT) | from;
| ^~
Fixes:
4343d00872e1 ("afs: Get rid of the afs_writeback record")
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 26 Oct 2020 13:22:47 +0000 (13:22 +0000)]
afs: Wrap page->private manipulations in inline functions
The afs filesystem uses page->private to store the dirty range within a
page such that in the event of a conflicting 3rd-party write to the server,
we write back just the bits that got changed locally.
However, there are a couple of problems with this:
(1) I need a bit to note if the page might be mapped so that partial
invalidation doesn't shrink the range.
(2) There aren't necessarily sufficient bits to store the entire range of
data altered (say it's a 32-bit system with 64KiB pages or transparent
huge pages are in use).
So wrap the accesses in inline functions so that future commits can change
how this works.
Also move them out of the tracing header into the in-directory header.
There's not really any need for them to be in the tracing header.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 26 Oct 2020 14:05:33 +0000 (14:05 +0000)]
afs: Fix where page->private is set during write
In afs, page->private is set to indicate the dirty region of a page. This
is done in afs_write_begin(), but that can't take account of whether the
copy into the page actually worked.
Fix this by moving the change of page->private into afs_write_end().
Fixes:
4343d00872e1 ("afs: Get rid of the afs_writeback record")
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Thu, 22 Oct 2020 13:03:03 +0000 (14:03 +0100)]
afs: Fix page leak on afs_write_begin() failure
Fix the leak of the target page in afs_write_begin() when it fails.
Fixes:
15b4650e55e0 ("afs: convert to new aops")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Nick Piggin <npiggin@gmail.com>
David Howells [Wed, 21 Oct 2020 12:22:19 +0000 (13:22 +0100)]
afs: Fix to take ref on page when PG_private is set
Fix afs to take a ref on a page when it sets PG_private on it and to drop
the ref when removing the flag.
Note that in afs_write_begin(), a lot of the time, PG_private is already
set on a page to which we're going to add some data. In such a case, we
leave the bit set and mustn't increment the page count.
As suggested by Matthew Wilcox, use attach/detach_page_private() where
possible.
Fixes:
31143d5d515e ("AFS: implement basic file write support")
Reported-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Linus Torvalds [Wed, 28 Oct 2020 19:05:14 +0000 (12:05 -0700)]
Merge tag 'trace-v5.10-rc1' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Fix synthetic event "strcat" overrun
New synthetic event code used strcat() and miscalculated the ending,
causing the concatenation to write beyond the allocated memory.
Instead of using strncat(), the code is switched over to seq_buf which
has all the mechanisms in place to protect against writing more than
what is allocated, and cleans up the code a bit"
* tag 'trace-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing, synthetic events: Replace buggy strcat() with seq_buf operations
Theodore Ts'o [Wed, 28 Oct 2020 17:39:13 +0000 (13:39 -0400)]
ext4: indicate that fast_commit is available via /sys/fs/ext4/feature/...
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Daniel Rosenberg [Wed, 28 Oct 2020 05:08:20 +0000 (05:08 +0000)]
ext4: use generic casefolding support
This switches ext4 over to the generic support provided in libfs.
Since casefolded dentries behave the same in ext4 and f2fs, we decrease
the maintenance burden by unifying them, and any optimizations will
immediately apply to both.
Signed-off-by: Daniel Rosenberg <drosen@google.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20201028050820.1636571-1-drosen@google.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
yangerkun [Wed, 28 Oct 2020 05:56:17 +0000 (13:56 +0800)]
ext4: do not use extent after put_bh
ext4_ext_search_right() will read more extent blocks and call put_bh
after we get the information we need. However, ret_ex will break this
and may cause use-after-free once pagecache has been freed. Fix it by
copying the extent structure if needed.
Signed-off-by: yangerkun <yangerkun@huawei.com>
Link: https://lore.kernel.org/r/20201028055617.2569255-1-yangerkun@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Harshad Shirwadkar [Tue, 27 Oct 2020 20:43:42 +0000 (13:43 -0700)]
ext4: use IS_ERR() for error checking of path
With this fix, fast commit recovery code uses IS_ERR() for path
returned by ext4_find_extent.
Fixes:
8016e29f4362 ("ext4: fast commit recovery path")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201027204342.2794949-1-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Jan Kara [Tue, 27 Oct 2020 13:27:51 +0000 (14:27 +0100)]
ext4: fix mmap write protection for data=journal mode
Commit
afb585a97f81 "ext4: data=journal: write-protect pages on
j_submit_inode_data_buffers()") added calls ext4_jbd2_inode_add_write()
to track inode ranges whose mappings need to get write-protected during
transaction commits. However the added calls use wrong start of a range
(0 instead of page offset) and so write protection is not necessarily
effective. Use correct range start to fix the problem.
Fixes:
afb585a97f81 ("ext4: data=journal: write-protect pages on j_submit_inode_data_buffers()")
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20201027132751.29858-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Mauro Carvalho Chehab [Tue, 27 Oct 2020 09:51:27 +0000 (10:51 +0100)]
jbd2: fix a kernel-doc markup
The kernel-doc markup that documents _fc_replay_callback is
missing an asterisk, causing this warning:
../include/linux/jbd2.h:1271: warning: Function parameter or member 'j_fc_replay_callback' not described in 'journal_s'
When building the docs.
Fixes:
609f928af48f ("jbd2: fast commit recovery path")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/6055927ada2015b55b413cdd2670533bdc9a8da2.1603791716.git.mchehab+huawei@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Harshad Shirwadkar [Tue, 27 Oct 2020 04:49:15 +0000 (21:49 -0700)]
ext4: use s_mount_flags instead of s_mount_state for fast commit state
Ext4's fast commit related transient states should use
sb->s_mount_flags instead of persistent sb->s_mount_state.
Fixes:
8016e29f4362 ("ext4: fast commit recovery path")
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201027044915.2553163-3-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Harshad Shirwadkar [Tue, 27 Oct 2020 04:49:14 +0000 (21:49 -0700)]
ext4: make num of fast commit blocks configurable
This patch reserves a field in the jbd2 superblock for number of fast
commit blocks. When this value is non-zero, Ext4 uses this field to
set the number of fast commit blocks.
Fixes:
6866d7b3f2bb ("ext4/jbd2: add fast commit initialization")
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201027044915.2553163-2-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Andrea Righi [Tue, 27 Oct 2020 04:49:13 +0000 (21:49 -0700)]
ext4: properly check for dirty state in ext4_inode_datasync_dirty()
ext4_inode_datasync_dirty() needs to return 'true' if the inode is
dirty, 'false' otherwise, but the logic seems to be incorrectly changed
by commit
aa75f4d3daae ("ext4: main fast-commit commit path").
This introduces a problem with swap files that are always failing to be
activated, showing this error in dmesg:
[ 34.406479] swapon: file is not committed
Simple test case to reproduce the problem:
# fallocate -l 8G swapfile
# chmod 0600 swapfile
# mkswap swapfile
# swapon swapfile
Fix the logic to return the proper state of the inode.
Link: https://lore.kernel.org/lkml/20201024131333.GA32124@xps-13-7390
Fixes:
8016e29f4362 ("ext4: fast commit recovery path")
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201027044915.2553163-1-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Harshad Shirwadkar [Fri, 23 Oct 2020 16:13:39 +0000 (09:13 -0700)]
ext4: fix double locking in ext4_fc_commit_dentry_updates()
Fixed double locking of sbi->s_fc_lock in the above function
as reported by kernel-test-robot.
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201023161339.1449437-1-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Alok Prasad [Wed, 21 Oct 2020 11:50:08 +0000 (11:50 +0000)]
RDMA/qedr: Fix memory leak in iWARP CM
Fixes memory leak in iWARP CM
Fixes:
e411e0587e0d ("RDMA/qedr: Add iWARP connection management functions")
Link: https://lore.kernel.org/r/20201021115008.28138-1-palok@marvell.com
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Jason Gunthorpe [Mon, 26 Oct 2020 14:25:49 +0000 (11:25 -0300)]
RDMA: Add rdma_connect_locked()
There are two flows for handling RDMA_CM_EVENT_ROUTE_RESOLVED, either the
handler triggers a completion and another thread does rdma_connect() or
the handler directly calls rdma_connect().
In all cases rdma_connect() needs to hold the handler_mutex, but when
handler's are invoked this is already held by the core code. This causes
ULPs using the 2nd method to deadlock.
Provide a rdma_connect_locked() and have all ULPs call it from their
handlers.
Link: https://lore.kernel.org/r/0-v2-53c22d5c1405+33-rdma_connect_locking_jgg@nvidia.com
Reported-and-tested-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Fixes:
2a7cec538169 ("RDMA/cma: Fix locking for the RDMA_CM_CONNECT state")
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Robert Hancock [Mon, 26 Oct 2020 17:58:02 +0000 (11:58 -0600)]
net: phylink: disable BMCR_ISOLATE in phylink_mii_c22_pcs_config
The Xilinx PCS/PMA PHY requires that BMCR_ISOLATE be disabled for proper
operation in 1000BaseX mode. It should be safe to ensure this bit is
disabled in phylink_mii_c22_pcs_config in all cases.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20201026175802.1332477-1-robert.hancock@calian.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Leon Romanovsky [Mon, 26 Oct 2020 12:33:27 +0000 (14:33 +0200)]
net: protect tcf_block_unbind with block lock
The tcf_block_unbind() expects that the caller will take block->cb_lock
before calling it, however the code took RTNL lock and dropped cb_lock
instead. This causes to the following kernel panic.
WARNING: CPU: 1 PID: 13524 at net/sched/cls_api.c:1488 tcf_block_unbind+0x2db/0x420
Modules linked in: mlx5_ib mlx5_core mlxfw ptp pps_core act_mirred act_tunnel_key cls_flower vxlan ip6_udp_tunnel udp_tunnel dummy sch_ingress openvswitch nsh xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 br_netfilter rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad ib_ipoib rdma_cm iw_cm ib_cm ib_uverbs ib_core overlay [last unloaded: mlxfw]
CPU: 1 PID: 13524 Comm: test-ecmp-add-v Tainted: G W 5.9.0+ #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:tcf_block_unbind+0x2db/0x420
Code: ff 48 83 c4 40 5b 5d 41 5c 41 5d 41 5e 41 5f c3 49 8d bc 24 30 01 00 00 be ff ff ff ff e8 7d 7f 70 00 85 c0 0f 85 7b fd ff ff <0f> 0b e9 74 fd ff ff 48 c7 c7 dc 6a 24 84 e8 02 ec fe fe e9 55 fd
RSP: 0018:
ffff888117d17968 EFLAGS:
00010246
RAX:
0000000000000000 RBX:
ffff88812f713c00 RCX:
1ffffffff0848d5b
RDX:
0000000000000001 RSI:
ffff88814fbc8130 RDI:
ffff888107f2b878
RBP:
1ffff11022fa2f3f R08:
0000000000000000 R09:
ffffffff84115a87
R10:
fffffbfff0822b50 R11:
ffff888107f2b898 R12:
ffff88814fbc8000
R13:
ffff88812f713c10 R14:
ffff888117d17a38 R15:
ffff88814fbc80c0
FS:
00007f6593d36740(0000) GS:
ffff8882a4f00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00005607a00758f8 CR3:
0000000131aea006 CR4:
0000000000170ea0
Call Trace:
tc_block_indr_cleanup+0x3e0/0x5a0
? tcf_block_unbind+0x420/0x420
? __mutex_unlock_slowpath+0xe7/0x610
flow_indr_dev_unregister+0x5e2/0x930
? mlx5e_restore_tunnel+0xdf0/0xdf0 [mlx5_core]
? mlx5e_restore_tunnel+0xdf0/0xdf0 [mlx5_core]
? flow_indr_block_cb_alloc+0x3c0/0x3c0
? mlx5_db_free+0x37c/0x4b0 [mlx5_core]
mlx5e_cleanup_rep_tx+0x8b/0xc0 [mlx5_core]
mlx5e_detach_netdev+0xe5/0x120 [mlx5_core]
mlx5e_vport_rep_unload+0x155/0x260 [mlx5_core]
esw_offloads_disable+0x227/0x2b0 [mlx5_core]
mlx5_eswitch_disable_locked.cold+0x38e/0x699 [mlx5_core]
mlx5_eswitch_disable+0x94/0xf0 [mlx5_core]
mlx5_device_disable_sriov+0x183/0x1f0 [mlx5_core]
mlx5_core_sriov_configure+0xfd/0x230 [mlx5_core]
sriov_numvfs_store+0x261/0x2f0
? sriov_drivers_autoprobe_store+0x110/0x110
? sysfs_file_ops+0x170/0x170
? sysfs_file_ops+0x117/0x170
? sysfs_file_ops+0x170/0x170
kernfs_fop_write+0x1ff/0x3f0
? rcu_read_lock_any_held+0x6e/0x90
vfs_write+0x1f3/0x620
ksys_write+0xf9/0x1d0
? __x64_sys_read+0xb0/0xb0
? lockdep_hardirqs_on_prepare+0x273/0x3f0
? syscall_enter_from_user_mode+0x1d/0x50
do_syscall_64+0x2d/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
<...>
---[ end trace
bfdd028ada702879 ]---
Fixes:
0fdcf78d5973 ("net: use flow_indr_dev_setup_offload()")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20201026123327.1141066-1-leon@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Thomas Bogendoerfer [Mon, 26 Oct 2020 10:42:21 +0000 (11:42 +0100)]
ibmveth: Fix use of ibmveth in a bridge.
The check for src mac address in ibmveth_is_packet_unsupported is wrong.
Commit
6f2275433a2f wanted to shut down messages for loopback packets,
but now suppresses bridged frames, which are accepted by the hypervisor
otherwise bridging won't work at all.
Fixes:
6f2275433a2f ("ibmveth: Detect unsupported packets before sending to the hypervisor")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Link: https://lore.kernel.org/r/20201026104221.26570-1-msuchanek@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yi Li [Tue, 27 Oct 2020 05:59:04 +0000 (13:59 +0800)]
net: core: Use skb_is_gso() in skb_checksum_help()
No functional changes, just minor refactoring.
Signed-off-by: Yi Li <yili@winhong.com>
Link: https://lore.kernel.org/r/20201027055904.2683444-1-yili@winhong.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guillaume Nault [Mon, 26 Oct 2020 10:29:45 +0000 (11:29 +0100)]
net/sched: act_mpls: Add softdep on mpls_gso.ko
TCA_MPLS_ACT_PUSH and TCA_MPLS_ACT_MAC_PUSH might be used on gso
packets. Such packets will thus require mpls_gso.ko for segmentation.
v2: Drop dependency on CONFIG_NET_MPLS_GSO in Kconfig (from Jakub and
David).
Fixes:
2a2ea50870ba ("net: sched: add mpls manipulation actions to TC")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Link: https://lore.kernel.org/r/1f6cab15bbd15666795061c55563aaf6a386e90e.1603708007.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Gabbasov [Mon, 26 Oct 2020 10:21:30 +0000 (05:21 -0500)]
ravb: Fix bit fields checking in ravb_hwtstamp_get()
In the function ravb_hwtstamp_get() in ravb_main.c with the existing
values for RAVB_RXTSTAMP_TYPE_V2_L2_EVENT (0x2) and RAVB_RXTSTAMP_TYPE_ALL
(0x6)
if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_V2_L2_EVENT)
config.rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
else if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_ALL)
config.rx_filter = HWTSTAMP_FILTER_ALL;
if the test on RAVB_RXTSTAMP_TYPE_ALL should be true,
it will never be reached.
This issue can be verified with 'hwtstamp_config' testing program
(tools/testing/selftests/net/hwtstamp_config.c). Setting filter type
to ALL and subsequent retrieving it gives incorrect value:
$ hwtstamp_config eth0 OFF ALL
flags = 0
tx_type = OFF
rx_filter = ALL
$ hwtstamp_config eth0
flags = 0
tx_type = OFF
rx_filter = PTP_V2_L2_EVENT
Correct this by converting if-else's to switch.
Fixes:
c156633f1353 ("Renesas Ethernet AVB driver proper")
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Link: https://lore.kernel.org/r/20201026102130.29368-1-andrew_gabbasov@mentor.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dan Carpenter [Mon, 26 Oct 2020 08:01:27 +0000 (11:01 +0300)]
devlink: Unlock on error in dumpit()
This needs to unlock before returning.
Fixes:
544e7c33ec2f ("net: devlink: Add support for port regions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201026080127.GB1628785@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dan Carpenter [Mon, 26 Oct 2020 08:00:59 +0000 (11:00 +0300)]
devlink: Fix some error codes
These paths don't set the error codes. It's especially important in
devlink_nl_region_notify_build() where it leads to a NULL dereference in
the caller.
Fixes:
544e7c33ec2f ("net: devlink: Add support for port regions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201026080059.GA1628785@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vinay Kumar Yadav [Sun, 25 Oct 2020 19:42:29 +0000 (01:12 +0530)]
chelsio/chtls: fix memory leaks in CPL handlers
CPL handler functions chtls_pass_open_rpl() and
chtls_close_listsrv_rpl() should return CPL_RET_BUF_DONE
so that caller function will do skb free to avoid leak.
Fixes:
cc35c88ae4db ("crypto : chtls - CPL handler definition")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Link: https://lore.kernel.org/r/20201025194228.31271-1-vinay.yadav@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vinay Kumar Yadav [Sun, 25 Oct 2020 19:35:39 +0000 (01:05 +0530)]
chelsio/chtls: fix deadlock issue
In chtls_pass_establish() we hold child socket lock using bh_lock_sock
and we are again trying bh_lock_sock in add_to_reap_list, causing deadlock.
Remove bh_lock_sock in add_to_reap_list() as lock is already held.
Fixes:
cc35c88ae4db ("crypto : chtls - CPL handler definition")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Link: https://lore.kernel.org/r/20201025193538.31112-1-vinay.yadav@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xu Wang [Fri, 23 Oct 2020 09:21:07 +0000 (09:21 +0000)]
net: microchip: Remove unneeded variable ret
Remove unneeded variable ret used to store return value.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20201023092107.28065-1-vulab@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xu Wang [Fri, 23 Oct 2020 08:55:33 +0000 (16:55 +0800)]
vxge: remove unnecessary cast in kfree()
Remove unnecessary cast in the argument to kfree.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20201023085533.4792-1-vulab@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David Howells [Thu, 22 Oct 2020 13:40:31 +0000 (14:40 +0100)]
afs: Fix afs_launder_page to not clear PG_writeback
Fix afs_launder_page() to not clear PG_writeback on the page it is
laundering as the flag isn't set in this case.
Fixes:
4343d00872e1 ("afs: Get rid of the afs_writeback record")
Signed-off-by: David Howells <dhowells@redhat.com>
Dan Carpenter [Mon, 24 Aug 2020 08:58:12 +0000 (11:58 +0300)]
afs: Fix a use after free in afs_xattr_get_acl()
The "op" pointer is freed earlier when we call afs_put_operation().
Fixes:
e49c7b2f6de7 ("afs: Build an abstraction around an "operation" concept")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Colin Ian King <colin.king@canonical.com>
David Howells [Tue, 27 Oct 2020 10:42:56 +0000 (10:42 +0000)]
afs: Fix tracing deref-before-check
The patch
dca54a7bbb8c: "afs: Add tracing for cell refcount and active user
count" from Oct 13, 2020, leads to the following Smatch complaint:
fs/afs/cell.c:596 afs_unuse_cell()
warn: variable dereferenced before check 'cell' (see line 592)
Fix this by moving the retrieval of the cell debug ID to after the check of
the validity of the cell pointer.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes:
dca54a7bbb8c ("afs: Add tracing for cell refcount and active user count")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Dan Carpenter <dan.carpenter@oracle.com>
David Howells [Tue, 27 Oct 2020 09:39:04 +0000 (09:39 +0000)]
afs: Fix copy_file_range()
The prevention of splice-write without explicit ops made the
copy_file_write() syscall to an afs file (as done by the generic/112
xfstest) fail with EINVAL.
Fix by using iter_file_splice_write() for afs.
Fixes:
36e2c7421f02 ("fs: don't allow splice read/write without explicit ops")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Linus Torvalds [Tue, 27 Oct 2020 21:39:29 +0000 (14:39 -0700)]
Merge tag 'x86-urgent-2020-10-27' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A couple of x86 fixes which missed rc1 due to my stupidity:
- Drop lazy TLB mode before switching to the temporary address space
for text patching.
text_poke() switches to the temporary mm which clears the lazy mode
and restores the original mm afterwards. Due to clearing lazy mode
this might restore a already dead mm if exit_mmap() runs in
parallel on another CPU.
- Document the x32 syscall design fail vs. syscall numbers 512-547
properly.
- Fix the ORC unwinder to handle the inactive task frame correctly.
This was unearthed due to the slightly different code generation of
gcc-10.
- Use an up to date screen_info for the boot params of kexec instead
of the possibly stale and invalid version which happened to be
valid when the kexec kernel was loaded"
* tag 'x86-urgent-2020-10-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/alternative: Don't call text_poke() in lazy TLB mode
x86/syscalls: Document the fact that syscalls 512-547 are a legacy mistake
x86/unwind/orc: Fix inactive tasks with stack pointer in %sp on GCC 10 compiled kernels
hyperv_fb: Update screen_info after removing old framebuffer
x86/kexec: Use up-to-dated screen_info copy to fill boot params
Linus Torvalds [Tue, 27 Oct 2020 19:42:44 +0000 (12:42 -0700)]
Merge tag 'orphan-handling-v5.10-rc2' of git://git./linux/kernel/git/kees/linux
Pull orphan section fixes from Kees Cook:
"A couple corner cases were found from the link-time orphan section
handling series:
- arm: handle .ARM.exidx and .ARM.extab sections (Nathan Chancellor)
- x86: collect .ctors.* with .ctors (Kees Cook)"
* tag 'orphan-handling-v5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
arm/build: Always handle .ARM.exidx and .ARM.extab sections
vmlinux.lds.h: Keep .ctors.* with .ctors
Geert Uytterhoeven [Tue, 27 Oct 2020 18:22:46 +0000 (19:22 +0100)]
mm/process_vm_access: Add missing #include <linux/compat.h>
With e.g. m68k/defconfig:
mm/process_vm_access.c: In function ‘process_vm_rw’:
mm/process_vm_access.c:277:5: error: implicit declaration of function ‘in_compat_syscall’ [-Werror=implicit-function-declaration]
277 | in_compat_syscall());
| ^~~~~~~~~~~~~~~~~
Fix this by adding #include <linux/compat.h>.
Reported-by: noreply@ellerman.id.au
Reported-by: damian <damian.tometzki@familie-tometzki.de>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Fixes:
38dc5079da7081e8 ("Fix compat regression in process_vm_rw()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nathan Chancellor [Mon, 28 Sep 2020 22:48:54 +0000 (15:48 -0700)]
arm/build: Always handle .ARM.exidx and .ARM.extab sections
After turning on warnings for orphan section placement, enabling
CONFIG_UNWINDER_FRAME_POINTER instead of CONFIG_UNWINDER_ARM causes
thousands of warnings when clang + ld.lld are used:
$ scripts/config --file arch/arm/configs/multi_v7_defconfig \
-d CONFIG_UNWINDER_ARM \
-e CONFIG_UNWINDER_FRAME_POINTER
$ make -skj"$(nproc)" ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- LLVM=1 defconfig zImage
ld.lld: warning: init/built-in.a(main.o):(.ARM.extab) is being placed in '.ARM.extab'
ld.lld: warning: init/built-in.a(main.o):(.ARM.extab.init.text) is being placed in '.ARM.extab.init.text'
ld.lld: warning: init/built-in.a(main.o):(.ARM.extab.ref.text) is being placed in '.ARM.extab.ref.text'
ld.lld: warning: init/built-in.a(do_mounts.o):(.ARM.extab.init.text) is being placed in '.ARM.extab.init.text'
ld.lld: warning: init/built-in.a(do_mounts.o):(.ARM.extab) is being placed in '.ARM.extab'
ld.lld: warning: init/built-in.a(do_mounts_rd.o):(.ARM.extab.init.text) is being placed in '.ARM.extab.init.text'
ld.lld: warning: init/built-in.a(do_mounts_rd.o):(.ARM.extab) is being placed in '.ARM.extab'
ld.lld: warning: init/built-in.a(do_mounts_initrd.o):(.ARM.extab.init.text) is being placed in '.ARM.extab.init.text'
ld.lld: warning: init/built-in.a(initramfs.o):(.ARM.extab.init.text) is being placed in '.ARM.extab.init.text'
ld.lld: warning: init/built-in.a(initramfs.o):(.ARM.extab) is being placed in '.ARM.extab'
ld.lld: warning: init/built-in.a(calibrate.o):(.ARM.extab.init.text) is being placed in '.ARM.extab.init.text'
ld.lld: warning: init/built-in.a(calibrate.o):(.ARM.extab) is being placed in '.ARM.extab'
These sections are handled by the ARM_UNWIND_SECTIONS define, which is
only added to the list of sections when CONFIG_ARM_UNWIND is set.
CONFIG_ARM_UNWIND is a hidden symbol that is only selected when
CONFIG_UNWINDER_ARM is set so CONFIG_UNWINDER_FRAME_POINTER never
handles these sections. According to the help text of
CONFIG_UNWINDER_ARM, these sections should be discarded so that the
kernel image size is not affected.
Fixes:
5a17850e251a ("arm/build: Warn on orphan section placement")
Link: https://github.com/ClangBuiltLinux/linux/issues/1152
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Review-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
[kees: Made the discard slightly more specific]
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20200928224854.3224862-1-natechancellor@gmail.com
Kees Cook [Mon, 5 Oct 2020 02:57:20 +0000 (19:57 -0700)]
vmlinux.lds.h: Keep .ctors.* with .ctors
Under some circumstances, the compiler generates .ctors.* sections. This
is seen doing a cross compile of x86_64 from a powerpc64el host:
x86_64-linux-gnu-ld: warning: orphan section `.ctors.65435' from `kernel/trace/trace_clock.o' being
placed in section `.ctors.65435'
x86_64-linux-gnu-ld: warning: orphan section `.ctors.65435' from `kernel/trace/ftrace.o' being
placed in section `.ctors.65435'
x86_64-linux-gnu-ld: warning: orphan section `.ctors.65435' from `kernel/trace/ring_buffer.o' being
placed in section `.ctors.65435'
Include these orphans along with the regular .ctors section.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes:
83109d5d5fba ("x86/build: Warn on orphan section placement")
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20201005025720.2599682-1-keescook@chromium.org
Linus Torvalds [Tue, 27 Oct 2020 17:01:24 +0000 (10:01 -0700)]
Merge tag 'devicetree-fixes-for-5.10-1' of git://git./linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- More binding additionalProperties/unevaluatedProperties additions
- More yamllint fixes on additions in the merge window
- CrOS embedded controller schema updates to fix warnings
- LEDs schema update adding ID_RGB
- A reserved-memory fix for regions starting at address 0x0
* tag 'devicetree-fixes-for-5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: Another round of adding missing 'additionalProperties/unevalutatedProperties'
dt-bindings: Explicitly allow additional properties in board/SoC schemas
dt-bindings: More whitespace clean-ups in schema files
mfd: google,cros-ec: add missing properties
dt-bindings: input: convert cros-ec-keyb to json-schema
dt-bindings: i2c: convert i2c-cros-ec-tunnel to json-schema
of: Fix reserved-memory overlap detection
dt-bindings: mailbox: mtk-gce: fix incorrect mbox-cells value
dt-bindings: leds: Update devicetree documents for ID_RGB
Jens Axboe [Tue, 27 Oct 2020 00:03:18 +0000 (18:03 -0600)]
Fix compat regression in process_vm_rw()
The removal of compat_process_vm_{readv,writev} didn't change
process_vm_rw(), which always assumes it's not doing a compat syscall.
Instead of passing in 'false' unconditionally for 'compat', make it
conditional on in_compat_syscall().
[ Both Al and Christoph point out that trying to access a 64-bit process
from a 32-bit one cannot work anyway, and is likely better prohibited,
but that's a separate issue - Linus ]
Fixes:
c3973b401ef2 ("mm: remove compat_process_vm_{readv,writev}")
Reported-and-tested-by: Kyle Huey <me@kylehuey.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Steven Rostedt (VMware) [Fri, 23 Oct 2020 23:00:49 +0000 (19:00 -0400)]
tracing, synthetic events: Replace buggy strcat() with seq_buf operations
There was a memory corruption bug happening while running the synthetic
event selftests:
kmemleak: Cannot insert 0xffff8c196fa2afe5 into the object search tree (overlaps existing)
CPU: 5 PID: 6866 Comm: ftracetest Tainted: G W 5.9.0-rc5-test+ #577
Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v03.03 07/14/2016
Call Trace:
dump_stack+0x8d/0xc0
create_object.cold+0x3b/0x60
slab_post_alloc_hook+0x57/0x510
? tracing_map_init+0x178/0x340
__kmalloc+0x1b1/0x390
tracing_map_init+0x178/0x340
event_hist_trigger_func+0x523/0xa40
trigger_process_regex+0xc5/0x110
event_trigger_write+0x71/0xd0
vfs_write+0xca/0x210
ksys_write+0x70/0xf0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fef0a63a487
Code: 64 89 02 48 c7 c0 ff ff ff ff eb bb 0f 1f 80 00 00 00 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24
RSP: 002b:
00007fff76f18398 EFLAGS:
00000246 ORIG_RAX:
0000000000000001
RAX:
ffffffffffffffda RBX:
0000000000000039 RCX:
00007fef0a63a487
RDX:
0000000000000039 RSI:
000055eb3b26d690 RDI:
0000000000000001
RBP:
000055eb3b26d690 R08:
000000000000000a R09:
0000000000000038
R10:
000055eb3b2cdb80 R11:
0000000000000246 R12:
0000000000000039
R13:
00007fef0a70b500 R14:
0000000000000039 R15:
00007fef0a70b700
kmemleak: Kernel memory leak detector disabled
kmemleak: Object 0xffff8c196fa2afe0 (size 8):
kmemleak: comm "ftracetest", pid 6866, jiffies
4295082531
kmemleak: min_count = 1
kmemleak: count = 0
kmemleak: flags = 0x1
kmemleak: checksum = 0
kmemleak: backtrace:
__kmalloc+0x1b1/0x390
tracing_map_init+0x1be/0x340
event_hist_trigger_func+0x523/0xa40
trigger_process_regex+0xc5/0x110
event_trigger_write+0x71/0xd0
vfs_write+0xca/0x210
ksys_write+0x70/0xf0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The cause came down to a use of strcat() that was adding an string that was
shorten, but the strcat() did not take that into account.
strcat() is extremely dangerous as it does not care how big the buffer is.
Replace it with seq_buf operations that prevent the buffer from being
overwritten if what is being written is bigger than the buffer.
Fixes:
10819e25799a ("tracing: Handle synthetic event array field type checking correctly")
Reviewed-by: Tom Zanussi <zanussi@kernel.org>
Tested-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Zenghui Yu [Fri, 23 Oct 2020 05:15:50 +0000 (13:15 +0800)]
net: hns3: Clear the CMDQ registers before unmapping BAR region
When unbinding the hns3 driver with the HNS3 VF, I got the following
kernel panic:
[ 265.709989] Unable to handle kernel paging request at virtual address
ffff800054627000
[ 265.717928] Mem abort info:
[ 265.720740] ESR = 0x96000047
[ 265.723810] EC = 0x25: DABT (current EL), IL = 32 bits
[ 265.729126] SET = 0, FnV = 0
[ 265.732195] EA = 0, S1PTW = 0
[ 265.735351] Data abort info:
[ 265.738227] ISV = 0, ISS = 0x00000047
[ 265.742071] CM = 0, WnR = 1
[ 265.745055] swapper pgtable: 4k pages, 48-bit VAs, pgdp=
0000000009b54000
[ 265.751753] [
ffff800054627000] pgd=
0000202ffffff003, p4d=
0000202ffffff003, pud=
00002020020eb003, pmd=
00000020a0dfc003, pte=
0000000000000000
[ 265.764314] Internal error: Oops:
96000047 [#1] SMP
[ 265.830357] CPU: 61 PID: 20319 Comm: bash Not tainted 5.9.0+ #206
[ 265.836423] Hardware name: Huawei TaiShan 2280 V2/BC82AMDDA, BIOS 1.05 09/18/2019
[ 265.843873] pstate:
80400009 (Nzcv daif +PAN -UAO -TCO BTYPE=--)
[ 265.843890] pc : hclgevf_cmd_uninit+0xbc/0x300
[ 265.861988] lr : hclgevf_cmd_uninit+0xb0/0x300
[ 265.861992] sp :
ffff80004c983b50
[ 265.881411] pmr_save:
000000e0
[ 265.884453] x29:
ffff80004c983b50 x28:
ffff20280bbce500
[ 265.889744] x27:
0000000000000000 x26:
0000000000000000
[ 265.895034] x25:
ffff800011a1f000 x24:
ffff800011a1fe90
[ 265.900325] x23:
ffff0020ce9b00d8 x22:
ffff0020ce9b0150
[ 265.905616] x21:
ffff800010d70e90 x20:
ffff800010d70e90
[ 265.910906] x19:
ffff0020ce9b0080 x18:
0000000000000004
[ 265.916198] x17:
0000000000000000 x16:
ffff800011ae32e8
[ 265.916201] x15:
0000000000000028 x14:
0000000000000002
[ 265.916204] x13:
ffff800011ae32e8 x12:
0000000000012ad8
[ 265.946619] x11:
ffff80004c983b50 x10:
0000000000000000
[ 265.951911] x9 :
ffff8000115d0888 x8 :
0000000000000000
[ 265.951914] x7 :
ffff800011890b20 x6 :
c0000000ffff7fff
[ 265.951917] x5 :
ffff80004c983930 x4 :
0000000000000001
[ 265.951919] x3 :
ffffa027eec1b000 x2 :
2b78ccbbff369100
[ 265.964487] x1 :
0000000000000000 x0 :
ffff800054627000
[ 265.964491] Call trace:
[ 265.964494] hclgevf_cmd_uninit+0xbc/0x300
[ 265.964496] hclgevf_uninit_ae_dev+0x9c/0xe8
[ 265.964501] hnae3_unregister_ae_dev+0xb0/0x130
[ 265.964516] hns3_remove+0x34/0x88 [hns3]
[ 266.009683] pci_device_remove+0x48/0xf0
[ 266.009692] device_release_driver_internal+0x114/0x1e8
[ 266.030058] device_driver_detach+0x28/0x38
[ 266.034224] unbind_store+0xd4/0x108
[ 266.037784] drv_attr_store+0x40/0x58
[ 266.041435] sysfs_kf_write+0x54/0x80
[ 266.045081] kernfs_fop_write+0x12c/0x250
[ 266.049076] vfs_write+0xc4/0x248
[ 266.052378] ksys_write+0x74/0xf8
[ 266.055677] __arm64_sys_write+0x24/0x30
[ 266.059584] el0_svc_common.constprop.3+0x84/0x270
[ 266.064354] do_el0_svc+0x34/0xa0
[ 266.067658] el0_svc+0x38/0x40
[ 266.070700] el0_sync_handler+0x8c/0xb0
[ 266.074519] el0_sync+0x140/0x180
It looks like the BAR memory region had already been unmapped before we
start clearing CMDQ registers in it, which is pretty bad and the kernel
happily kills itself because of a Current EL Data Abort (on arm64).
Moving the CMDQ uninitialization a bit early fixes the issue for me.
Fixes:
862d969a3a4d ("net: hns3: do VF's pci re-initialization while PF doing FLR")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20201023051550.793-1-yuzenghui@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 27 Oct 2020 01:26:38 +0000 (18:26 -0700)]
Merge branch 'bnxt_en-bug-fixes'
Michael Chan says:
====================
bnxt_en: Bug fixes.
These 5 bug fixes are all related to the firmware reset or AER recovery.
2 patches fix the cleanup logic for the workqueue used to handle firmware
reset and recovery. 1 patch ensures that the chip will have the proper
BAR addresses latched after fatal AER recovery. 1 patch fixes the
open path to check for firmware reset abort error. The last one
sends the fw reset command unconditionally to fix the AER reset logic.
====================
Link: https://lore.kernel.org/r/1603685901-17917-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vasundhara Volam [Mon, 26 Oct 2020 04:18:21 +0000 (00:18 -0400)]
bnxt_en: Send HWRM_FUNC_RESET fw command unconditionally.
In the AER or firmware reset flow, if we are in fatal error state or
if pci_channel_offline() is true, we don't send any commands to the
firmware because the commands will likely not reach the firmware and
most commands don't matter much because the firmware is likely to be
reset imminently.
However, the HWRM_FUNC_RESET command is different and we should always
attempt to send it. In the AER flow for example, the .slot_reset()
call will trigger this fw command and we need to try to send it to
effect the proper reset.
Fixes:
b340dc680ed4 ("bnxt_en: Avoid sending firmware messages when AER error is detected.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan [Mon, 26 Oct 2020 04:18:20 +0000 (00:18 -0400)]
bnxt_en: Check abort error state in bnxt_open_nic().
bnxt_open_nic() is called during configuration changes that require
the NIC to be closed and then opened. This call is protected by
rtnl_lock. Firmware reset can be happening at the same time. Only
critical portions of the entire firmware reset sequence are protected
by the rtnl_lock. It is possible that bnxt_open_nic() can be called
when the firmware reset sequence is aborting. In that case,
bnxt_open_nic() needs to check if the ABORT_ERR flag is set and
abort if it is. The configuration change that resulted in the
bnxt_open_nic() call will fail but the NIC will be brought to a
consistent IF_DOWN state.
Without this patch, if bnxt_open_nic() were to continue in this error
state, it may crash like this:
[ 1648.659736] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 1648.659768] IP: [<
ffffffffc01e9b3a>] bnxt_alloc_mem+0x50a/0x1140 [bnxt_en]
[ 1648.659796] PGD
101e1b3067 PUD
101e1b2067 PMD 0
[ 1648.659813] Oops: 0000 [#1] SMP
[ 1648.659825] Modules linked in: xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 tun bridge stp llc ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter sunrpc dell_smbios dell_wmi_descriptor dcdbas amd64_edac_mod edac_mce_amd kvm_amd kvm irqbypass crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper vfat cryptd fat pcspkr ipmi_ssif sg k10temp i2c_piix4 wmi ipmi_si ipmi_devintf ipmi_msghandler tpm_crb acpi_power_meter sch_fq_codel ip_tables xfs libcrc32c sd_mod crc_t10dif crct10dif_generic mgag200 i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm ahci drm libahci megaraid_sas crct10dif_pclmul crct10dif_common
[ 1648.660063] tg3 libata crc32c_intel bnxt_en(OE) drm_panel_orientation_quirks devlink ptp pps_core dm_mirror dm_region_hash dm_log dm_mod fuse
[ 1648.660105] CPU: 13 PID: 3867 Comm: ethtool Kdump: loaded Tainted: G OE ------------ 3.10.0-1152.el7.x86_64 #1
[ 1648.660911] Hardware name: Dell Inc. PowerEdge R7515/0R4CNN, BIOS 1.2.14 01/28/2020
[ 1648.661662] task:
ffff94e64cbc9080 ti:
ffff94f55df1c000 task.ti:
ffff94f55df1c000
[ 1648.662409] RIP: 0010:[<
ffffffffc01e9b3a>] [<
ffffffffc01e9b3a>] bnxt_alloc_mem+0x50a/0x1140 [bnxt_en]
[ 1648.663171] RSP: 0018:
ffff94f55df1fba8 EFLAGS:
00010202
[ 1648.663927] RAX:
0000000000000000 RBX:
ffff94e6827e0000 RCX:
0000000000000000
[ 1648.664684] RDX:
0000000000000000 RSI:
0000000000000000 RDI:
ffff94e6827e08c0
[ 1648.665433] RBP:
ffff94f55df1fc20 R08:
00000000000001ff R09:
0000000000000008
[ 1648.666184] R10:
0000000000000d53 R11:
ffff94f55df1f7ce R12:
ffff94e6827e08c0
[ 1648.666940] R13:
ffff94e6827e08c0 R14:
ffff94e6827e08c0 R15:
ffffffffb9115e40
[ 1648.667695] FS:
00007f8aadba5740(0000) GS:
ffff94f57eb40000(0000) knlGS:
0000000000000000
[ 1648.668447] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 1648.669202] CR2:
0000000000000000 CR3:
0000001022772000 CR4:
0000000000340fe0
[ 1648.669966] Call Trace:
[ 1648.670730] [<
ffffffffc01f1d5d>] ? bnxt_need_reserve_rings+0x9d/0x170 [bnxt_en]
[ 1648.671496] [<
ffffffffc01fa7ea>] __bnxt_open_nic+0x8a/0x9a0 [bnxt_en]
[ 1648.672263] [<
ffffffffc01f7479>] ? bnxt_close_nic+0x59/0x1b0 [bnxt_en]
[ 1648.673031] [<
ffffffffc01fb11b>] bnxt_open_nic+0x1b/0x50 [bnxt_en]
[ 1648.673793] [<
ffffffffc020037c>] bnxt_set_ringparam+0x6c/0xa0 [bnxt_en]
[ 1648.674550] [<
ffffffffb8a5f564>] dev_ethtool+0x1334/0x21a0
[ 1648.675306] [<
ffffffffb8a719ff>] dev_ioctl+0x1ef/0x5f0
[ 1648.676061] [<
ffffffffb8a324bd>] sock_do_ioctl+0x4d/0x60
[ 1648.676810] [<
ffffffffb8a326bb>] sock_ioctl+0x1eb/0x2d0
[ 1648.677548] [<
ffffffffb8663230>] do_vfs_ioctl+0x3a0/0x5b0
[ 1648.678282] [<
ffffffffb8b8e678>] ? __do_page_fault+0x238/0x500
[ 1648.679016] [<
ffffffffb86634e1>] SyS_ioctl+0xa1/0xc0
[ 1648.679745] [<
ffffffffb8b93f92>] system_call_fastpath+0x25/0x2a
[ 1648.680461] Code: 9e 60 01 00 00 0f 1f 40 00 45 8b 8e 48 01 00 00 31 c9 45 85 c9 0f 8e 73 01 00 00 66 0f 1f 44 00 00 49 8b 86 a8 00 00 00 48 63 d1 <48> 8b 14 d0 48 85 d2 0f 84 46 01 00 00 41 8b 86 44 01 00 00 c7
[ 1648.681986] RIP [<
ffffffffc01e9b3a>] bnxt_alloc_mem+0x50a/0x1140 [bnxt_en]
[ 1648.682724] RSP <
ffff94f55df1fba8>
[ 1648.683451] CR2:
0000000000000000
Fixes:
ec5d31e3c15d ("bnxt_en: Handle firmware reset status during IF_UP.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vasundhara Volam [Mon, 26 Oct 2020 04:18:19 +0000 (00:18 -0400)]
bnxt_en: Re-write PCI BARs after PCI fatal error.
When a PCIe fatal error occurs, the internal latched BAR addresses
in the chip get reset even though the BAR register values in config
space are retained.
pci_restore_state() will not rewrite the BAR addresses if the
BAR address values are valid, causing the chip's internal BAR addresses
to stay invalid. So we need to zero the BAR registers during PCIe fatal
error to force pci_restore_state() to restore the BAR addresses. These
write cycles to the BAR registers will cause the proper BAR addresses to
latch internally.
Fixes:
6316ea6db93d ("bnxt_en: Enable AER support.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vasundhara Volam [Mon, 26 Oct 2020 04:18:18 +0000 (00:18 -0400)]
bnxt_en: Invoke cancel_delayed_work_sync() for PFs also.
As part of the commit
b148bb238c02
("bnxt_en: Fix possible crash in bnxt_fw_reset_task()."),
cancel_delayed_work_sync() is called only for VFs to fix a possible
crash by cancelling any pending delayed work items. It was assumed
by mistake that the flush_workqueue() call on the PF would flush
delayed work items as well.
As flush_workqueue() does not cancel the delayed workqueue, extend
the fix for PFs. This fix will avoid the system crash, if there are
any pending delayed work items in fw_reset_task() during driver's
.remove() call.
Unify the workqueue cleanup logic for both PF and VF by calling
cancel_work_sync() and cancel_delayed_work_sync() directly in
bnxt_remove_one().
Fixes:
b148bb238c02 ("bnxt_en: Fix possible crash in bnxt_fw_reset_task().")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vasundhara Volam [Mon, 26 Oct 2020 04:18:17 +0000 (00:18 -0400)]
bnxt_en: Fix regression in workqueue cleanup logic in bnxt_remove_one().
A recent patch has moved the workqueue cleanup logic before
calling unregister_netdev() in bnxt_remove_one(). This caused a
regression because the workqueue can be restarted if the device is
still open. Workqueue cleanup must be done after unregister_netdev().
The workqueue will not restart itself after the device is closed.
Call bnxt_cancel_sp_work() after unregister_netdev() and
call bnxt_dl_fw_reporters_destroy() after that. This fixes the
regession and the original NULL ptr dereference issue.
Fixes:
b16939b59cc0 ("bnxt_en: Fix NULL ptr dereference crash in bnxt_fw_reset_task()")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 26 Oct 2020 23:45:53 +0000 (16:45 -0700)]
Merge branch 'mlxsw-various-fixes'
Ido Schimmel says:
====================
mlxsw: Various fixes
This patch set contains various fixes for mlxsw.
Patch #1 ensures that only link modes that are supported by both the
device and the driver are advertised. When a link mode that is not
supported by the driver is negotiated by the device, it will be
presented as an unknown speed by ethtool, causing the bond driver to
wrongly assume that the link is down.
Patch #2 fixes a trivial memory leak upon module removal.
Patch #3 fixes a use-after-free that syzkaller was able to trigger once
on a slow emulator after a few months of fuzzing.
====================
Link: https://lore.kernel.org/r/20201024133733.2107509-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Sat, 24 Oct 2020 13:37:33 +0000 (16:37 +0300)]
mlxsw: core: Fix use-after-free in mlxsw_emad_trans_finish()
Each EMAD transaction stores the skb used to issue the EMAD request
('trans->tx_skb') so that the request could be retried in case of a
timeout. The skb can be freed when a corresponding response is received
or as part of the retry logic (e.g., failed retransmit, exceeded maximum
number of retries).
The two tasks (i.e., response processing and retransmits) are
synchronized by the atomic 'trans->active' field which ensures that
responses to inactive transactions are ignored.
In case of a failed retransmit the transaction is finished and all of
its resources are freed. However, the current code does not mark it as
inactive. Syzkaller was able to hit a race condition in which a
concurrent response is processed while the transaction's resources are
being freed, resulting in a use-after-free [1].
Fix the issue by making sure to mark the transaction as inactive after a
failed retransmit and free its resources only if a concurrent task did
not already do that.
[1]
BUG: KASAN: use-after-free in consume_skb+0x30/0x370
net/core/skbuff.c:833
Read of size 4 at addr
ffff88804f570494 by task syz-executor.0/1004
CPU: 0 PID: 1004 Comm: syz-executor.0 Not tainted 5.8.0-rc7+ #68
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xf6/0x16e lib/dump_stack.c:118
print_address_description.constprop.0+0x1c/0x250
mm/kasan/report.c:383
__kasan_report mm/kasan/report.c:513 [inline]
kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530
check_memory_region_inline mm/kasan/generic.c:186 [inline]
check_memory_region+0x14e/0x1b0 mm/kasan/generic.c:192
instrument_atomic_read include/linux/instrumented.h:56 [inline]
atomic_read include/asm-generic/atomic-instrumented.h:27 [inline]
refcount_read include/linux/refcount.h:147 [inline]
skb_unref include/linux/skbuff.h:1044 [inline]
consume_skb+0x30/0x370 net/core/skbuff.c:833
mlxsw_emad_trans_finish+0x64/0x1c0 drivers/net/ethernet/mellanox/mlxsw/core.c:592
mlxsw_emad_process_response drivers/net/ethernet/mellanox/mlxsw/core.c:651 [inline]
mlxsw_emad_rx_listener_func+0x5c9/0xac0 drivers/net/ethernet/mellanox/mlxsw/core.c:672
mlxsw_core_skb_receive+0x4df/0x770 drivers/net/ethernet/mellanox/mlxsw/core.c:2063
mlxsw_pci_cqe_rdq_handle drivers/net/ethernet/mellanox/mlxsw/pci.c:595 [inline]
mlxsw_pci_cq_tasklet+0x12a6/0x2520 drivers/net/ethernet/mellanox/mlxsw/pci.c:651
tasklet_action_common.isra.0+0x13f/0x3e0 kernel/softirq.c:550
__do_softirq+0x223/0x964 kernel/softirq.c:292
asm_call_on_stack+0x12/0x20 arch/x86/entry/entry_64.S:711
Allocated by task 1006:
save_stack+0x1b/0x40 mm/kasan/common.c:48
set_track mm/kasan/common.c:56 [inline]
__kasan_kmalloc mm/kasan/common.c:494 [inline]
__kasan_kmalloc.constprop.0+0xc2/0xd0 mm/kasan/common.c:467
slab_post_alloc_hook mm/slab.h:586 [inline]
slab_alloc_node mm/slub.c:2824 [inline]
slab_alloc mm/slub.c:2832 [inline]
kmem_cache_alloc+0xcd/0x2e0 mm/slub.c:2837
__build_skb+0x21/0x60 net/core/skbuff.c:311
__netdev_alloc_skb+0x1e2/0x360 net/core/skbuff.c:464
netdev_alloc_skb include/linux/skbuff.h:2810 [inline]
mlxsw_emad_alloc drivers/net/ethernet/mellanox/mlxsw/core.c:756 [inline]
mlxsw_emad_reg_access drivers/net/ethernet/mellanox/mlxsw/core.c:787 [inline]
mlxsw_core_reg_access_emad+0x1ab/0x1420 drivers/net/ethernet/mellanox/mlxsw/core.c:1817
mlxsw_reg_trans_query+0x39/0x50 drivers/net/ethernet/mellanox/mlxsw/core.c:1831
mlxsw_sp_sb_pm_occ_clear drivers/net/ethernet/mellanox/mlxsw/spectrum_buffers.c:260 [inline]
mlxsw_sp_sb_occ_max_clear+0xbff/0x10a0 drivers/net/ethernet/mellanox/mlxsw/spectrum_buffers.c:1365
mlxsw_devlink_sb_occ_max_clear+0x76/0xb0 drivers/net/ethernet/mellanox/mlxsw/core.c:1037
devlink_nl_cmd_sb_occ_max_clear_doit+0x1ec/0x280 net/core/devlink.c:1765
genl_family_rcv_msg_doit net/netlink/genetlink.c:669 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:714 [inline]
genl_rcv_msg+0x617/0x980 net/netlink/genetlink.c:731
netlink_rcv_skb+0x152/0x440 net/netlink/af_netlink.c:2470
genl_rcv+0x24/0x40 net/netlink/genetlink.c:742
netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline]
netlink_unicast+0x53a/0x750 net/netlink/af_netlink.c:1330
netlink_sendmsg+0x850/0xd90 net/netlink/af_netlink.c:1919
sock_sendmsg_nosec net/socket.c:651 [inline]
sock_sendmsg+0x150/0x190 net/socket.c:671
____sys_sendmsg+0x6d8/0x840 net/socket.c:2359
___sys_sendmsg+0xff/0x170 net/socket.c:2413
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2446
do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:384
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Freed by task 73:
save_stack+0x1b/0x40 mm/kasan/common.c:48
set_track mm/kasan/common.c:56 [inline]
kasan_set_free_info mm/kasan/common.c:316 [inline]
__kasan_slab_free+0x12c/0x170 mm/kasan/common.c:455
slab_free_hook mm/slub.c:1474 [inline]
slab_free_freelist_hook mm/slub.c:1507 [inline]
slab_free mm/slub.c:3072 [inline]
kmem_cache_free+0xbe/0x380 mm/slub.c:3088
kfree_skbmem net/core/skbuff.c:622 [inline]
kfree_skbmem+0xef/0x1b0 net/core/skbuff.c:616
__kfree_skb net/core/skbuff.c:679 [inline]
consume_skb net/core/skbuff.c:837 [inline]
consume_skb+0xe1/0x370 net/core/skbuff.c:831
mlxsw_emad_trans_finish+0x64/0x1c0 drivers/net/ethernet/mellanox/mlxsw/core.c:592
mlxsw_emad_transmit_retry.isra.0+0x9d/0xc0 drivers/net/ethernet/mellanox/mlxsw/core.c:613
mlxsw_emad_trans_timeout_work+0x43/0x50 drivers/net/ethernet/mellanox/mlxsw/core.c:625
process_one_work+0xa3e/0x17a0 kernel/workqueue.c:2269
worker_thread+0x9e/0x1050 kernel/workqueue.c:2415
kthread+0x355/0x470 kernel/kthread.c:291
ret_from_fork+0x22/0x30 arch/x86/entry/entry_64.S:293
The buggy address belongs to the object at
ffff88804f5703c0
which belongs to the cache skbuff_head_cache of size 224
The buggy address is located 212 bytes inside of
224-byte region [
ffff88804f5703c0,
ffff88804f5704a0)
The buggy address belongs to the page:
page:
ffffea00013d5c00 refcount:1 mapcount:0 mapping:
0000000000000000
index:0x0
flags: 0x100000000000200(slab)
raw:
0100000000000200 dead000000000100 dead000000000122 ffff88806c625400
raw:
0000000000000000 00000000000c000c 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88804f570380: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
ffff88804f570400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>
ffff88804f570480: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff88804f570500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff88804f570580: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc
Fixes:
caf7297e7ab5f ("mlxsw: core: Introduce support for asynchronous EMAD register access")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel [Sat, 24 Oct 2020 13:37:32 +0000 (16:37 +0300)]
mlxsw: core: Fix memory leak on module removal
Free the devlink instance during the teardown sequence in the non-reload
case to avoid the following memory leak.
unreferenced object 0xffff888232895000 (size 2048):
comm "modprobe", pid 1073, jiffies
4295568857 (age 164.871s)
hex dump (first 32 bytes):
00 01 00 00 00 00 ad de 22 01 00 00 00 00 ad de ........".......
10 50 89 32 82 88 ff ff 10 50 89 32 82 88 ff ff .P.2.....P.2....
backtrace:
[<
00000000c704e9a6>] __kmalloc+0x13a/0x2a0
[<
00000000ee30129d>] devlink_alloc+0xff/0x760
[<
0000000092ab3e5d>] 0xffffffffa042e5b0
[<
000000004f3f8a31>] 0xffffffffa042f6ad
[<
0000000092800b4b>] 0xffffffffa0491df3
[<
00000000c4843903>] local_pci_probe+0xcb/0x170
[<
000000006993ded7>] pci_device_probe+0x2c2/0x4e0
[<
00000000a8e0de75>] really_probe+0x2c5/0xf90
[<
00000000d42ba75d>] driver_probe_device+0x1eb/0x340
[<
00000000bcc95e05>] device_driver_attach+0x294/0x300
[<
000000000e2bc177>] __driver_attach+0x167/0x2f0
[<
000000007d44cd6e>] bus_for_each_dev+0x148/0x1f0
[<
000000003cd5a91e>] driver_attach+0x45/0x60
[<
000000000041ce51>] bus_add_driver+0x3b8/0x720
[<
00000000f5215476>] driver_register+0x230/0x4e0
[<
00000000d79356f5>] __pci_register_driver+0x190/0x200
Fixes:
a22712a96291 ("mlxsw: core: Fix devlink unregister flow")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reported-by: Vadim Pasternak <vadimp@nvidia.com>
Tested-by: Oleksandr Shamray <oleksandrs@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Sat, 24 Oct 2020 13:37:31 +0000 (16:37 +0300)]
mlxsw: Only advertise link modes supported by both driver and device
During port creation the driver instructs the device to advertise all
the supported link modes queried from the device.
Since cited commit not all the link modes supported by the device are
supported by the driver. This can result in the device negotiating a
link mode that is not recognized by the driver causing ethtool to show
an unsupported speed:
$ ethtool swp1
...
Speed: Unknown!
This is especially problematic when the netdev is enslaved to a bond, as
the bond driver uses unknown speed as an indication that the link is
down:
[13048.900895] net_ratelimit: 86 callbacks suppressed
[13048.900902] t_bond0: (slave swp52): failed to get link speed/duplex
[13048.912160] t_bond0: (slave swp49): failed to get link speed/duplex
Fix this by making sure that only link modes that are supported by both
the device and the driver are advertised.
Fixes:
b97cd891268d ("mlxsw: Remove 56G speed support")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 26 Oct 2020 23:29:38 +0000 (16:29 -0700)]
Merge branch 'net-smc-fixes-2020-10-23'
Karsten Graul says:
====================
net/smc: fixes 2020-10-23
Patch 1 fixes a potential null pointer dereference. Patch 2 takes care
of a suppressed return code and patch 3 corrects the system EID in the
ISM driver.
====================
Link: https://lore.kernel.org/r/20201023184830.59548-1-kgraul@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Karsten Graul [Fri, 23 Oct 2020 18:48:30 +0000 (20:48 +0200)]
s390/ism: fix incorrect system EID
The system EID that is defined by the ISM driver is not correct. Using
an incorrect system EID allows to communicate with remote Linux systems
that use the same incorrect system EID, but when it comes to
interoperability with other operating systems then the system EIDs do
never match which prevents SMC-Dv2 communication.
Using the correct system EID fixes this problem.
Fixes:
201091ebb2a1 ("net/smc: introduce System Enterprise ID (SEID)")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Karsten Graul [Fri, 23 Oct 2020 18:48:29 +0000 (20:48 +0200)]
net/smc: fix suppressed return code
The patch that repaired the invalid return code in smcd_new_buf_create()
missed to take care of errno ENOSPC which has a special meaning that no
more DMBEs can be registered on the device. Fix that by keeping this
errno value during the translation of the return code.
Fixes:
6b1bbf94ab36 ("net/smc: fix invalid return code in smcd_new_buf_create()")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Karsten Graul [Fri, 23 Oct 2020 18:48:28 +0000 (20:48 +0200)]
net/smc: fix null pointer dereference in smc_listen_decline()
smc_listen_work() calls smc_listen_decline() on label out_decl,
providing the ini pointer variable. But this pointer can still be null
when the label out_decl is reached.
Fix this by checking the ini variable in smc_listen_work() and call
smc_listen_decline() with the result directly.
Fixes:
a7c9c5f4af7f ("net/smc: CLC accept / confirm V2")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jeff Vander Stoep [Fri, 23 Oct 2020 14:37:57 +0000 (16:37 +0200)]
vsock: use ns_capable_noaudit() on socket create
During __vsock_create() CAP_NET_ADMIN is used to determine if the
vsock_sock->trusted should be set to true. This value is used later
for determing if a remote connection should be allowed to connect
to a restricted VM. Unfortunately, if the caller doesn't have
CAP_NET_ADMIN, an audit message such as an selinux denial is
generated even if the caller does not want a trusted socket.
Logging errors on success is confusing. To avoid this, switch the
capable(CAP_NET_ADMIN) check to the noaudit version.
Reported-by: Roman Kiryanov <rkir@google.com>
https://android-review.googlesource.com/c/device/generic/goldfish/+/
1468545/
Signed-off-by: Jeff Vander Stoep <jeffv@google.com>
Reviewed-by: James Morris <jamorris@linux.microsoft.com>
Link: https://lore.kernel.org/r/20201023143757.377574-1-jeffv@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Raju Rangoju [Fri, 23 Oct 2020 11:58:52 +0000 (17:28 +0530)]
cxgb4: set up filter action after rewrites
The current code sets up the filter action field before
rewrites are set up. When the action 'switch' is used
with rewrites, this may result in initial few packets
that get switched out don't have rewrites applied
on them.
So, make sure filter action is set up along with rewrites
or only after everything else is set up for rewrites.
Fixes:
12b276fbf6e0 ("cxgb4: add support to create hash filters")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Link: https://lore.kernel.org/r/20201023115852.18262-1-rajur@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dan Carpenter [Fri, 23 Oct 2020 11:22:12 +0000 (14:22 +0300)]
net: hns3: clean up a return in hclge_tm_bp_setup()
Smatch complains that "ret" might be uninitialized if we don't enter
the loop. We do always enter the loop so it's a false positive, but
it's cleaner to just return a literal zero and that silences the
warning as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201023112212.GA282278@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Mon, 26 Oct 2020 22:45:22 +0000 (15:45 -0700)]
scsi: qla2xxx: remove incorrect sparse #ifdef
The code to try to shut up sparse warnings about questionable locking
didn't shut up sparse: it made the result not parse as valid C at all,
since the end result now has a label with no statement.
The proper fix is to just always lock the hardware, the same way Bart
did in commit
8ae178760b23 ("scsi: qla2xxx: Simplify the functions for
dumping firmware"). That avoids the whole problem with having locking
that is not statically obvious.
But in the meantime, just remove the incorrect attempt at trying to
avoid a sparse warning that just made things worse.
This was exposed by commit
3e6efab865ac ("scsi: qla2xxx: Fix reset of
MPI firmware"), very similarly to how commit
cbb01c2f2f63 ("scsi:
qla2xxx: Fix MPI failure AEN (8200) handling") exposed the same problem
in another place, and caused that commit
8ae178760b23.
Please don't add code to just shut up sparse without actually fixing
what sparse complains about.
Reported-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Arun Easi <aeasi@marvell.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 26 Oct 2020 22:39:37 +0000 (15:39 -0700)]
arch/um: partially revert the conversion to __section() macro
A couple of um files ended up not including the header file that defines
the __section() macro, and the simplest fix is to just revert the change
for those files.
Fixes:
33def8498fdd treewide: Convert macro and uses of __section(foo) to __section("foo")
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gal Pressman [Mon, 26 Oct 2020 08:26:21 +0000 (10:26 +0200)]
RDMA/uverbs: Fix false error in query gid IOCTL
Some drivers (such as EFA) have a GID table, but aren't IB/RoCE devices.
Remove the unnecessary rdma_ib_or_roce() check.
This fixes rdma-core failures for EFA when it uses the new ioctl interface
for querying the GID table.
Fixes:
9f85cbe50aa0 ("RDMA/uverbs: Expose the new GID query API to user space")
Link: https://lore.kernel.org/r/20201026082621.32463-1-galpress@amazon.com
Signed-off-by: Gal Pressman <galpress@amazon.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Parav Pandit [Mon, 26 Oct 2020 13:43:59 +0000 (15:43 +0200)]
RDMA/mlx5: Fix devlink deadlock on net namespace deletion
When a mlx5 core devlink instance is reloaded in different net namespace,
its associated IB device is deleted and recreated.
Example sequence is:
$ ip netns add foo
$ devlink dev reload pci/0000:00:08.0 netns foo
$ ip netns del foo
mlx5 IB device needs to attach and detach the netdevice to it through the
netdev notifier chain during load and unload sequence. A below call graph
of the unload flow.
cleanup_net()
down_read(&pernet_ops_rwsem); <- first sem acquired
ops_pre_exit_list()
pre_exit()
devlink_pernet_pre_exit()
devlink_reload()
mlx5_devlink_reload_down()
mlx5_unload_one()
[...]
mlx5_ib_remove()
mlx5_ib_unbind_slave_port()
mlx5_remove_netdev_notifier()
unregister_netdevice_notifier()
down_write(&pernet_ops_rwsem);<- recurrsive lock
Hence, when net namespace is deleted, mlx5 reload results in deadlock.
When deadlock occurs, devlink mutex is also held. This not only deadlocks
the mlx5 device under reload, but all the processes which attempt to
access unrelated devlink devices are deadlocked.
Hence, fix this by mlx5 ib driver to register for per net netdev notifier
instead of global one, which operats on the net namespace without holding
the pernet_ops_rwsem.
Fixes:
4383cfcc65e7 ("net/mlx5: Add devlink reload")
Link: https://lore.kernel.org/r/20201026134359.23150-1-parav@nvidia.com
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Bob Pearson [Fri, 16 Oct 2020 21:13:44 +0000 (16:13 -0500)]
RDMA/rxe: Fix small problem in network_type patch
The patch referenced below has a typo that results in using the wrong L2
header size for outbound traffic. (V4 <-> V6).
It also breaks kernel-side RC traffic because they use AVs that use
RDMA_NETWORK_XXX enums instead of RXE_NETWORK_TYPE_XXX enums. Fix this by
transcoding between these enum types.
Fixes:
e0d696d201dd ("RDMA/rxe: Move the definitions for rxe_av.network_type to uAPI")
Link: https://lore.kernel.org/r/20201016211343.22906-1-rpearson@hpe.com
Signed-off-by: Bob Pearson <rpearson@hpe.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Rob Herring [Tue, 6 Oct 2020 17:19:08 +0000 (12:19 -0500)]
dt-bindings: Another round of adding missing 'additionalProperties/unevalutatedProperties'
Another round of wack-a-mole. The json-schema default is additional
unknown properties are allowed, but for DT all properties should be
defined.
Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Mon, 5 Oct 2020 18:38:29 +0000 (13:38 -0500)]
dt-bindings: Explicitly allow additional properties in board/SoC schemas
In order to add meta-schema checks for additional/unevaluatedProperties
being present, all schema need to make this explicit. As the top-level
board/SoC schemas always have additional properties, add
'additionalProperties: true'.
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201005183830.486085-4-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Tue, 21 Apr 2020 02:24:47 +0000 (21:24 -0500)]
dt-bindings: More whitespace clean-ups in schema files
Clean-up incorrect indentation, extra spaces, and missing EOF newline in
schema files. Most of the clean-ups are for list indentation which
should always be 2 spaces more than the preceding keyword.
Found with yamllint (now integrated into the checks).
Cc: linux-arm-kernel@lists.infradead.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-i2c@vger.kernel.org
Cc: linux-iio@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-serial@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Sam Ravnborg <sam@ravnborg.org> # for display
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio
Signed-off-by: Rob Herring <robh@kernel.org>
Ricardo Cañuelo [Wed, 21 Oct 2020 11:43:08 +0000 (13:43 +0200)]
mfd: google,cros-ec: add missing properties
Add missing properties that are currently used in the examples of
subnode bindings and in many DTs.
Also updates the example in sound/google,cros-ec-codec.yaml to comply
with the google,cros-ec binding.
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Link: https://lore.kernel.org/r/20201021114308.25485-4-ricardo.canuelo@collabora.com
[robh: Add missing '#address-cells' and '#size-cells']
Signed-off-by: Rob Herring <robh@kernel.org>