OSDN Git Service
Antoine Ténart [Tue, 22 Aug 2017 17:08:24 +0000 (19:08 +0200)]
net: mvpp2: initialize the GMAC when using a port
This adds a routine to initialize the GMAC at the port level when using
a port. This wasn't done until this commit, and the mvpp2 driver was
relying on the bootloader/firmware initialization. This doesn't mean
everything is configured in the mvpp2 driver now, but it helps reducing
the gap.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Ténart [Tue, 22 Aug 2017 17:08:23 +0000 (19:08 +0200)]
net: mvpp2: move the mii configuration in the ndo_open path
This moves the mii configuration in the ndo_open path, to allow handling
different mii configurations later and to switch between these
configurations at runtime.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Ténart [Tue, 22 Aug 2017 17:08:22 +0000 (19:08 +0200)]
net: mvpp2: fix the synchronization module bypass macro name
The macro defining the bit to toggle to bypass or not the
synchronization module is wrongly named. Writing 1 will disable bypass.
This patch s/MVPP22_CTRL4_SYNC_BYPASS/MVPP22_CTRL4_SYNC_BYPASS_DIS/.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Ténart [Tue, 22 Aug 2017 17:08:21 +0000 (19:08 +0200)]
net: mvpp2: unify register definitions coding style
Cosmetic patch to use the same formatting rules on all register
definitions.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
William Tu [Tue, 22 Aug 2017 16:40:28 +0000 (09:40 -0700)]
gre: introduce native tunnel support for ERSPAN
The patch adds ERSPAN type II tunnel support. The implementation
is based on the draft at [1]. One of the purposes is for Linux
box to be able to receive ERSPAN monitoring traffic sent from
the Cisco switch, by creating a ERSPAN tunnel device.
In addition, the patch also adds ERSPAN TX, so Linux virtual
switch can redirect monitored traffic to the ERSPAN tunnel device.
The traffic will be encapsulated into ERSPAN and sent out.
The implementation reuses tunnel key as ERSPAN session ID, and
field 'erspan' as ERSPAN Index fields:
./ip link add dev ers11 type erspan seq key 100 erspan 123 \
local 172.16.1.200 remote 172.16.1.100
To use the above device as ERSPAN receiver, configure
Nexus 5000 switch as below:
monitor session 100 type erspan-source
erspan-id 123
vrf default
destination ip 172.16.1.200
source interface Ethernet1/11 both
source interface Ethernet1/12 both
no shut
monitor erspan origin ip-address 172.16.1.100 global
[1] https://tools.ietf.org/html/draft-foschiano-erspan-01
[2] iproute2 patch: http://marc.info/?l=linux-netdev&m=
150306086924951&w=2
[3] test script: http://marc.info/?l=linux-netdev&m=
150231021807304&w=2
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: Meenakshi Vohra <mvohra@vmware.com>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Tue, 22 Aug 2017 15:39:57 +0000 (11:39 -0400)]
udp: remove unreachable ufo branches
Remove two references to ufo in the udp send path that are no longer
reachable now that ufo has been removed.
Commit
85f1bd9a7b5a ("udp: consistently apply ufo or fragmentation")
is a fix to ufo. It is safe to revert what remains of it.
Also, no skb can enter ip_append_page with skb_is_gso true now that
skb_shinfo(skb)->gso_type is no longer set in ip_append_page/_data.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bhumika Goyal [Tue, 22 Aug 2017 08:13:29 +0000 (13:43 +0530)]
net: mdio-gpio: make mdiobb_ops const
Make this const as it is only stored in a const field of a
mdiobb_ctrl structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bhumika Goyal [Tue, 22 Aug 2017 08:15:59 +0000 (13:45 +0530)]
net: ethernet: freescale: fs_enet: make mdiobb_ops const
Make this const as it is only stored in a const field of a
mdiobb_ctrl structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bhumika Goyal [Tue, 22 Aug 2017 08:11:19 +0000 (13:41 +0530)]
net: ethernet: ax88796: make mdiobb_ops const
Make this const as it is only stored in a const field of a
mdiobb_ctrl structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 22 Aug 2017 21:16:13 +0000 (14:16 -0700)]
Merge branch 'tcp_conn_request-cleanup'
Tonghao Zhang says:
====================
tcp: Simplify the tcp_conn_request.
Just simplify the tcp_conn_request function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tonghao Zhang [Tue, 22 Aug 2017 06:33:49 +0000 (23:33 -0700)]
tcp: Remove the unused parameter for tcp_try_fastopen.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tonghao Zhang [Tue, 22 Aug 2017 06:33:48 +0000 (23:33 -0700)]
tcp: Get a proper dst before checking it.
tcp_peer_is_proven needs a proper route to make the
determination, but dst always is NULL. This bug may
be there at the beginning of git tree. This does not
look serious enough to deserve backports to stable
versions.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 22 Aug 2017 21:08:12 +0000 (14:08 -0700)]
Merge branch 'hv_netvsc-Ethtool-handler-to-change-UDP-hash-levels'
Haiyang Zhang says:
====================
hv_netvsc: Ethtool handler to change UDP hash levels
The patch set adds the functions to switch UDP hash level between
L3 and L4 by ethtool command. UDP over IPv4 and v6 can be set
differently. The default hash level is L4. We currently only
allow switching TX hash level from within the guests.
The ethtool callback function is triggered by command line, and
update the per device variables of the hash level.
On Azure, fragmented UDP packets is not yet supported with L4
hashing, and may have high packet loss rate. Using L3 hashing is
recommended in this case. This ethtool option allows a user to
make this selection.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 22 Aug 2017 02:22:40 +0000 (19:22 -0700)]
hv_netvsc: Update netvsc Document for UDP hash level setting
Update Documentation/networking/netvsc.txt for UDP hash level setting
and related info.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 22 Aug 2017 02:22:39 +0000 (19:22 -0700)]
hv_netvsc: Add ethtool handler to set and get UDP hash levels
The patch add the functions to switch UDP hash level between
L3 and L4 by ethtool command. UDP over IPv4 and v6 can be set
differently. The default hash level is L4. We currently only
allow switching TX hash level from within the guests.
On Azure, fragmented UDP packets have high loss rate with L4
hashing. Using L3 hashing is recommended in this case.
For example, for UDP over IPv4 on eth0:
To include UDP port numbers in hasing:
ethtool -N eth0 rx-flow-hash udp4 sdfn
To exclude UDP port numbers in hasing:
ethtool -N eth0 rx-flow-hash udp4 sd
To show UDP hash level:
ethtool -n eth0 rx-flow-hash udp4
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 22 Aug 2017 02:22:38 +0000 (19:22 -0700)]
hv_netvsc: Clean up unused parameter from netvsc_get_rss_hash_opts()
The parameter "nvdev" is not in use.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 22 Aug 2017 02:22:37 +0000 (19:22 -0700)]
hv_netvsc: Clean up unused parameter from netvsc_get_hash()
The parameter "sk" is not in use.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 22 Aug 2017 18:08:16 +0000 (11:08 -0700)]
Merge branch 'liquidio-VF-driver-will-notify-NIC-firmware-of-MTU-change'
Veerasenareddy Burru says:
====================
liquidio: VF driver will notify NIC firmware of MTU change
Make VF driver notify NIC firmware of MTU change. Firmware needs this
information for MTU propagation and enforcement.
The first patch in this series moves a macro definition to a proper place
to prevent a build error in the second patch which has the code that sends
the notification.
Change Log:
V1 -> V2
* Add "From:" line to patch #1 and #2 to give credit to the author.
* In patch #2, order local variable declarations from longest to
shortest line.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Veerasenareddy Burru [Mon, 21 Aug 2017 19:35:59 +0000 (12:35 -0700)]
liquidio: make VF driver notify NIC firmware of MTU change
Signed-off-by: Veerasenareddy Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Veerasenareddy Burru [Mon, 21 Aug 2017 19:35:56 +0000 (12:35 -0700)]
liquidio: move macro definition to a proper place
The macro LIO_CMD_WAIT_TM is not specific to the PF driver; it can be used
by the VF driver too, so move its definition from a PF-specific header file
to one that's common to PF and VF.
Signed-off-by: Veerasenareddy Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bhumika Goyal [Mon, 21 Aug 2017 17:31:12 +0000 (23:01 +0530)]
ptp: make ptp_clock_info const
Make these const as they are only used in a copy operation.
Done using Coccinelle.
@match disable optional_qualifier@
identifier s;
@@
static struct ptp_clock_info s = {...};
@ref@
position p;
identifier match.s;
@@
s@p
@good1@
position ref.p;
identifier match.s,f,c;
expression e;
@@
(
e = s@p
|
e = s@p.f
|
c(...,s@p.f,...)
|
c(...,s@p,...)
)
@bad depends on !good1@
position ref.p;
identifier match.s;
@@
s@p
@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct ptp_clock_info s;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bhumika Goyal [Mon, 21 Aug 2017 17:06:50 +0000 (22:36 +0530)]
net: ethernet: make ptp_clock_info const
Make these const as they are only used in a copy operation.
Done using Coccinelle.
@match disable optional_qualifier@
identifier s;
@@
static struct ptp_clock_info s = {...};
@ref@
position p;
identifier match.s;
@@
s@p
@good1@
position ref.p;
identifier match.s,f,c;
expression e;
@@
(
e = s@p
|
e = s@p.f
|
c(...,s@p.f,...)
|
c(...,s@p,...)
)
@bad depends on !good1@
position ref.p;
identifier match.s;
@@
s@p
@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct ptp_clock_info s;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Salil [Mon, 21 Aug 2017 16:05:24 +0000 (17:05 +0100)]
net: hns3: Add support to change MTU in HNS3 hardware
This patch adds the following support to the HNS3 driver:
1. Support to change the Maximum Transmission Unit of a
port in the HNS NIC hardware.
2. Initializes the supported MTU range for the netdevice.
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 22 Aug 2017 17:48:54 +0000 (10:48 -0700)]
Merge branch 'Huawei-HiNIC-Ethernet-Driver'
Aviad Krawczyk says:
====================
Huawei HiNIC Ethernet Driver
The patch-set contains the support of the HiNIC Ethernet driver for
hinic family of PCIE Network Interface Cards.
The Huawei's PCIE HiNIC card is a new Ethernet card and hence there was
a need of a new driver.
The current driver is meant to be used for the Physical Function and there
would soon be a support for Virtual Function and more features once the
basic PF driver has been accepted.
Changes V7 -> V8:
1. Remove unnecessary cast from void * - Stephen Hemminger comment
https://lkml.org/lkml/2017/8/17/1008
Changes V6 -> V7:
1. Separate netpoll and MAINTAINERS patch - Sergei Shtylyov comment
https://lkml.org/lkml/2017/8/17/479
Changes V5 -> V6:
1. Fix cover letter Message-Id
Changes V4 -> V5:
1. Remove select_queue NOP - David Miller comment
https://lkml.org/lkml/2017/8/16/625
Changes V3 -> V4:
1. Reverse christmas tree order - David Miller comment
https://lkml.org/lkml/2017/8/3/862
Changes V2 -> V3:
1. Replace dev_ functions by netif_ functions - Joe Perches comment
https://lkml.org/lkml/2017/7/19/424
2. Fix the driver directory in MAINTAINERS file - Sergei Shtylyov comment
https://lkml.org/lkml/2017/7/19/615
3. Add a newline at the end of Makefile - David Miller comment
https://lkml.org/lkml/2017/7/19/1345
4. Return a pointer as a val instead of in arg - Francois Romieu comment
https://lkml.org/lkml/2017/7/19/1319
5. Change the error labels to err_xyz - Francois Romieu comment
https://lkml.org/lkml/2017/7/19/1319
6. Remove check of Func Type in free function - Francois Romieu comment
https://lkml.org/lkml/2017/7/19/1319
7. Remove !netdev check in remove function - Francois Romieu comment
https://lkml.org/lkml/2017/7/19/1319
8. Use module_pci_driver - Francois Romieu comment
https://lkml.org/lkml/2017/7/19/1319
9. Move the PCI device ID to the .c file - Francois Romieu comment
https://lkml.org/lkml/2017/7/19/1319
10. Remove void * to avoid passing wrong ptr - Francois Romieu comment
https://lkml.org/lkml/2017/7/19/1319
Changes V1 -> V2:
1. remove driver verstion - Andrew Lunn comment
https://lkml.org/lkml/2017/7/12/372
2. replace kzalloc by devm_kzalloc for short clean - Andrew Lunn comment
https://lkml.org/lkml/2017/7/12/372
3. replace pr_ functions by dev_ functions - Andrew Lunn comment
https://lkml.org/lkml/2017/7/12/375
4. seperate last patch by moving ops to a new patch - Andrew Lunn comment
https://lkml.org/lkml/2017/7/12/377
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:56:08 +0000 (23:56 +0800)]
net-next/hinic: Add Maintainer
Update MAINTAINERS file
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:56:07 +0000 (23:56 +0800)]
net-next/hinic: Add netpoll
Add more netdev operation - netpoll.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:56:06 +0000 (23:56 +0800)]
net-next/hinic: Add ethtool and stats
Add ethtool operations and statistics operations.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:56:05 +0000 (23:56 +0800)]
net-next/hinic: Add Tx operation
Add transmit operation for sending data by qp operations.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:56:04 +0000 (23:56 +0800)]
net-next/hinic: Add Rx handler
Set the io resources in the nic and handle rx events by qp operations.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:56:03 +0000 (23:56 +0800)]
net-next/hinic: Add cmdq completion handler
Add cmdq completion handler for getting a notification about the
completion of cmdq commands.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:56:02 +0000 (23:56 +0800)]
net-next/hinic: Add cmdq commands
Add cmdq commands for setting queue pair contexts in the nic.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:56:01 +0000 (23:56 +0800)]
net-next/hinic: Add ceqs
Initialize the completion event queues and handle ceq events by calling
the registered handlers. Used for cmdq command completion.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:56:00 +0000 (23:56 +0800)]
net-next/hinic: Initialize cmdq
Create the work queues for cmdq and update the nic about the work queue
contexts. cmdq commands are used for updating the nic about the qp
contexts.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:55:59 +0000 (23:55 +0800)]
net-next/hinic: Set qp context
Update the nic about the resources of the queue pairs.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:55:58 +0000 (23:55 +0800)]
net-next/hinic: Add qp resources
Create the resources for queue pair operations: doorbell area,
consumer index address and producer index address.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:55:57 +0000 (23:55 +0800)]
net-next/hinic: Add wq
Create work queues for being used by the queue pairs.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:55:56 +0000 (23:55 +0800)]
net-next/hinic: Add logical Txq and Rxq
Create the logical queues of the nic.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:55:55 +0000 (23:55 +0800)]
net-next/hinic: Add Rx mode and link event handler
Add port management message for setting Rx mode in the card,
used for rx_mode netdev operation.
The link event handler is used for getting a notification about the
link state.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:55:54 +0000 (23:55 +0800)]
net-next/hinic: Add port management commands
Add the port management commands that are sent as management messages.
The port management commands are used for netdev operations.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:55:53 +0000 (23:55 +0800)]
net-next/hinic: Add aeqs
Handle aeq elements that are accumulated on the aeq by calling the
registered handler for the specific event.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:55:52 +0000 (23:55 +0800)]
net-next/hinic: Add api cmd commands
Add the api cmd commands for sending management messages to the nic.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:55:51 +0000 (23:55 +0800)]
net-next/hinic: Add management messages
Add the management messages for sending to api cmd and the asynchronous
event handler for the completion of the messages.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:55:50 +0000 (23:55 +0800)]
net-next/hinic: Initialize api cmd hw
Update the hardware about api cmd resources and initialize it.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:55:49 +0000 (23:55 +0800)]
net-next/hinic: Initialize api cmd resources
Initialize api cmd resources as part of management initialization.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:55:48 +0000 (23:55 +0800)]
net-next/hinic: Initialize hw device components
Initialize hw device by calling the initialization functions of aeqs and
management channel.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Krawczyk [Mon, 21 Aug 2017 15:55:47 +0000 (23:55 +0800)]
net-next/hinic: Initialize hw interface
Initialize hw interface as part of the nic initialization for accessing hw.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Wu [Mon, 21 Aug 2017 10:12:55 +0000 (18:12 +0800)]
net: ethernet: stmmac: dwmac-rk: Add rv1108 gmac support
It only supports rmii interface. Add constants and callback functions
for the dwmac on rv1108 socs. As can be seen, the base structure is
the same, only registers and the bits in them moved slightly.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Mon, 21 Aug 2017 09:47:30 +0000 (12:47 +0300)]
ethernet: xircom: small clean up in setup_xirc2ps_cs()
The get_options() function takes the whole ARRAY_SIZE(). It doesn't
matter here because we don't use more than 7 elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shubham Bansal [Tue, 22 Aug 2017 06:32:33 +0000 (12:02 +0530)]
arm: eBPF JIT compiler
The JIT compiler emits ARM 32 bit instructions. Currently, It supports
eBPF only. Classic BPF is supported because of the conversion by BPF core.
This patch is essentially changing the current implementation of JIT compiler
of Berkeley Packet Filter from classic to internal with almost all
instructions from eBPF ISA supported except the following
BPF_ALU64 | BPF_DIV | BPF_K
BPF_ALU64 | BPF_DIV | BPF_X
BPF_ALU64 | BPF_MOD | BPF_K
BPF_ALU64 | BPF_MOD | BPF_X
BPF_STX | BPF_XADD | BPF_W
BPF_STX | BPF_XADD | BPF_DW
Implementation is using scratch space to emulate 64 bit eBPF ISA on 32 bit
ARM because of deficiency of general purpose registers on ARM. Currently,
only LITTLE ENDIAN machines are supported in this eBPF JIT Compiler.
Tested on ARMv7 with QEMU by me (Shubham Bansal).
Testing results on ARMv7:
1) test_bpf: Summary: 341 PASSED, 0 FAILED, [312/333 JIT'ed]
2) test_tag: OK (40945 tests)
3) test_progs: Summary: 30 PASSED, 0 FAILED
4) test_lpm: OK
5) test_lru_map: OK
Above tests are all done with following flags enabled discreatly.
1) bpf_jit_enable=1
a) CONFIG_FRAME_POINTER enabled
b) CONFIG_FRAME_POINTER disabled
2) bpf_jit_enable=1 and bpf_jit_harden=2
a) CONFIG_FRAME_POINTER enabled
b) CONFIG_FRAME_POINTER disabled
See Documentation/networking/filter.txt for more information.
Signed-off-by: Shubham Bansal <illusionist.neo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 22 Aug 2017 00:06:42 +0000 (17:06 -0700)]
Merge git://git./linux/kernel/git/davem/net
Linus Torvalds [Mon, 21 Aug 2017 21:07:48 +0000 (14:07 -0700)]
Merge git://git./linux/kernel/git/davem/sparc
Pull sparc fixes from David Miller:
"Just a couple small fixes, two of which have to do with gcc-7:
1) Don't clobber kernel fixed registers in __multi4 libgcc helper.
2) Fix a new uninitialized variable warning on sparc32 with gcc-7,
from Thomas Petazzoni.
3) Adjust pmd_t initializer on sparc32 to make gcc happy.
4) If ATU isn't available, don't bark in the logs. From Tushar Dave"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: kernel/pcic: silence gcc 7.x warning in pcibios_fixup_bus()
sparc64: remove unnecessary log message
sparc64: Don't clibber fixed registers in __multi4.
mm: add pmd_t initializer __pmd() to work around a GCC bug.
Thomas Petazzoni [Sun, 13 Aug 2017 21:14:58 +0000 (23:14 +0200)]
sparc: kernel/pcic: silence gcc 7.x warning in pcibios_fixup_bus()
When building the kernel for Sparc using gcc 7.x, the build fails
with:
arch/sparc/kernel/pcic.c: In function ‘pcibios_fixup_bus’:
arch/sparc/kernel/pcic.c:647:8: error: ‘cmd’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
cmd |= PCI_COMMAND_IO;
^~
The simplified code looks like this:
unsigned int cmd;
[...]
pcic_read_config(dev->bus, dev->devfn, PCI_COMMAND, 2, &cmd);
[...]
cmd |= PCI_COMMAND_IO;
I.e, the code assumes that pcic_read_config() will always initialize
cmd. But it's not the case. Looking at pcic_read_config(), if
bus->number is != 0 or if the size is not one of 1, 2 or 4, *val will
not be initialized.
As a simple fix, we initialize cmd to zero at the beginning of
pcibios_fixup_bus.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gao Feng [Fri, 18 Aug 2017 07:23:24 +0000 (15:23 +0800)]
net: sched: Add the invalid handle check in qdisc_class_find
Add the invalid handle "0" check to avoid unnecessary search, because
the qdisc uses the skb->priority as the handle value to look up, and
it is "0" usually.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Mon, 21 Aug 2017 15:59:30 +0000 (17:59 +0200)]
tipc: don't reset stale broadcast send link
When the broadcast send link after 100 attempts has failed to
transfer a packet to all peers, we consider it stale, and reset
it. Thereafter it needs to re-synchronize with the peers, something
currently done by just resetting and re-establishing all links to
all peers. This has turned out to be overkill, with potentially
unwanted consequences for the remaining cluster.
A closer analysis reveals that this can be done much simpler. When
this kind of failure happens, for reasons that may lie outside the
TIPC protocol, it is typically only one peer which is failing to
receive and acknowledge packets. It is hence sufficient to identify
and reset the links only to that peer to resolve the situation, without
having to reset the broadcast link at all. This solution entails a much
lower risk of negative consequences for the own node as well as for
the overall cluster.
We implement this change in this commit.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 21 Aug 2017 20:30:36 +0000 (13:30 -0700)]
Merge tag 'arc-4.13-rc7-fixes' of git://git./linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- PAE40 related updates
- SLC errata for region ops
- intc line masking by default
* tag 'arc-4.13-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
arc: Mask individual IRQ lines during core INTC init
ARCv2: PAE40: set MSB even if !CONFIG_ARC_HAS_PAE40 but PAE exists in SoC
ARCv2: PAE40: Explicitly set MSB counterpart of SLC region ops addresses
ARC: dma: implement dma_unmap_page and sg variant
ARCv2: SLC: Make sure busy bit is set properly for region ops
ARC: [plat-sim] Include this platform unconditionally
ARC: [plat-axs10x]: prepare dts files for enabling PAE40 on axs103
ARC: defconfig: Cleanup from old Kconfig options
Linus Torvalds [Mon, 21 Aug 2017 20:27:51 +0000 (13:27 -0700)]
Merge tag 'rtc-4.13-fixes' of git://git./linux/kernel/git/abelloni/linux
Pull RTC fix from Alexandre Belloni:
"Fix regmap configuration for ds1307"
* tag 'rtc-4.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: ds1307: fix regmap config
Linus Torvalds [Mon, 21 Aug 2017 20:16:27 +0000 (13:16 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix IGMP handling wrt VRF, from David Ahern.
2) Fix timer access to freed object in dccp, from Eric Dumazet.
3) Use kmalloc_array() in ptr_ring to avoid overflow cases which are
triggerable by userspace. Also from Eric Dumazet.
4) Fix infinite loop in unmapping cleanup of nfp driver, from Colin Ian
King.
5) Correct datagram peek handling of empty SKBs, from Matthew Dawson.
6) Fix use after free in TIPC, from Eric Dumazet.
7) When replacing a route in ipv6 we need to reset the round robin
pointer, from Wei Wang.
8) Fix bug in pci_find_pcie_root_port() which was unearthed by the
relaxed ordering changes, from Thierry Redding. I made sure to get
an explicit ACK from Bjorn this time around :-)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
ipv6: repair fib6 tree in failure case
net_sched: fix order of queue length updates in qdisc_replace()
tools lib bpf: improve warning
switchdev: documentation: minor typo fixes
bpf, doc: also add s390x as arch to sysctl description
net: sched: fix NULL pointer dereference when action calls some targets
rxrpc: Fix oops when discarding a preallocated service call
irda: do not leak initialized list.dev to userspace
net/mlx4_core: Enable 4K UAR if SRIOV module parameter is not enabled
PCI: Allow PCI express root ports to find themselves
tcp: when rearming RTO, if RTO time is in past then fire RTO ASAP
net: check and errout if res->fi is NULL when RTM_F_FIB_MATCH is set
ipv6: reset fn->rr_ptr when replacing route
sctp: fully initialize the IPv6 address in sctp_v6_to_addr()
tipc: fix use-after-free
tun: handle register_netdevice() failures properly
datagram: When peeking datagrams with offset < 0 don't skip empty skbs
bpf, doc: improve sysctl knob description
netxen: fix incorrect loop counter decrement
nfp: fix infinite loop on umapping cleanup
...
Oleg Nesterov [Mon, 21 Aug 2017 15:35:02 +0000 (17:35 +0200)]
pids: make task_tgid_nr_ns() safe
This was reported many times, and this was even mentioned in commit
52ee2dfdd4f5 ("pids: refactor vnr/nr_ns helpers to make them safe") but
somehow nobody bothered to fix the obvious problem: task_tgid_nr_ns() is
not safe because task->group_leader points to nowhere after the exiting
task passes exit_notify(), rcu_read_lock() can not help.
We really need to change __unhash_process() to nullify group_leader,
parent, and real_parent, but this needs some cleanups. Until then we
can turn task_tgid_nr_ns() into another user of __task_pid_nr_ns() and
fix the problem.
Reported-by: Troy Kensinger <tkensinger@google.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Lamparter [Fri, 18 Aug 2017 12:31:35 +0000 (14:31 +0200)]
net: check type when freeing metadata dst
Commit
3fcece12bc1b ("net: store port/representator id in metadata_dst")
added a new type field to metadata_dst, but metadata_dst_free() wasn't
updated to check it before freeing the METADATA_IP_TUNNEL specific dst
cache entry.
This is not currently causing problems since it's far enough back in the
struct to be zeroed for the only other type currently in existance
(METADATA_HW_PORT_MUX), but nevertheless it's not correct.
Fixes:
3fcece12bc1b ("net: store port/representator id in metadata_dst")
Signed-off-by: David Lamparter <equinox@diac24.net>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Sridhar Samudrala <sridhar.samudrala@intel.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 17 Aug 2017 19:17:20 +0000 (12:17 -0700)]
net: ipv6: put host and anycast routes on device with address
One nagging difference between ipv4 and ipv6 is host routes for ipv6
addresses are installed using the loopback device or VRF / L3 Master
device. e.g.,
2001:db8:1::/120 dev veth0 proto kernel metric 256 pref medium
local 2001:db8:1::1 dev lo table local proto kernel metric 0 pref medium
Using the loopback device is convenient -- necessary for local tx, but
has some nasty side effects, most notably setting the 'lo' device down
causes all host routes for all local IPv6 address to be removed from the
FIB and completely breaks IPv6 networking across all interfaces.
This patch puts FIB entries for IPv6 routes against the device. This
simplifies the routes in the FIB, for example by making dst->dev and
rt6i_idev->dev the same (a future patch can look at removing the device
reference taken for rt6i_idev for FIB entries).
When copies are made on FIB lookups, the cloned route has dst->dev
set to loopback (or the L3 master device). This is needed for the
local Tx of packets to local addresses.
With fib entries allocated against the real network device, the addrconf
code that reinserts host routes on admin up of 'lo' is no longer needed.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Thu, 17 Aug 2017 14:47:00 +0000 (16:47 +0200)]
dsa: remove unused net_device arg from handlers
compile tested only, but saw no warnings/errors with
allmodconfig build.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 21 Aug 2017 17:31:34 +0000 (10:31 -0700)]
Merge branch 'bpf-mips-jit-improvements'
David Daney says:
====================
MIPS,bpf: Improvements for MIPS eBPF JIT
Here are several improvements and bug fixes for the MIPS eBPF JIT.
The main change is the addition of support for JLT, JLE, JSLT and JSLE
ops, that were recently added.
Also fix WARN output when used with preemptable kernel, and a small
cleanup/optimization in the use of BPF_OP(insn->code).
I suggest that the whole thing go via the BPF/net-next path as there
are dependencies on code that is not yet merged to Linus' tree.
Still pending are changes to reduce stack usage when the verifier can
determine the maximum stack size.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Daney [Fri, 18 Aug 2017 23:40:33 +0000 (16:40 -0700)]
MIPS,bpf: Cache value of BPF_OP(insn->code) in eBPF JIT.
The code looks a little cleaner if we replace BPF_OP(insn->code) with
the local variable bpf_op. Caching the value this way also saves 300
bytes (about 1%) in the code size of the JIT.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Daney [Fri, 18 Aug 2017 23:40:32 +0000 (16:40 -0700)]
MIPS, bpf: Implement JLT, JLE, JSLT and JSLE ops in the eBPF JIT.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Daney [Fri, 18 Aug 2017 23:40:31 +0000 (16:40 -0700)]
MIPS,bpf: Fix using smp_processor_id() in preemptible splat.
If the kernel is configured with preemption enabled we were getting
warning stack traces for use of current_cpu_type().
Fix by moving the test between preempt_disable()/preempt_enable() and
caching the results of the CPU type tests for use during code
generation.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bhumika Goyal [Mon, 21 Aug 2017 11:43:10 +0000 (17:13 +0530)]
qlogic: make device_attribute const
Make these const as they are only passed as an argument to the
function device_create_file and device_remove_file and the corresponding
arguments are of type const.
Done using Coccinelle
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 21 Aug 2017 16:29:47 +0000 (09:29 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-08-21
1) Support RX checksum with IPsec crypto offload for esp4/esp6.
From Ilan Tayari.
2) Fixup IPv6 checksums when doing IPsec crypto offload.
From Yossi Kuperman.
3) Auto load the xfrom offload modules if a user installs
a SA that requests IPsec offload. From Ilan Tayari.
4) Clear RX offload informations in xfrm_input to not
confuse the TX path with stale offload informations.
From Ilan Tayari.
5) Allow IPsec GSO for local sockets if the crypto operation
will be offloaded.
6) Support setting of an output mark to the xfrm_state.
This mark can be used to to do the tunnel route lookup.
From Lorenzo Colitti.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Tue, 25 Jul 2017 16:44:04 +0000 (18:44 +0200)]
rtc: ds1307: fix regmap config
Current max_register setting breaks reading nvram on certain chips and
also reading the standard registers on RX8130 where register map starts
at 0x10.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes:
11e5890b5342 "rtc: ds1307: convert driver to regmap"
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Rick Farrington [Sat, 19 Aug 2017 01:21:49 +0000 (18:21 -0700)]
liquidio: fix use of pf in pass-through mode in a virtual machine
Fix problem when PF is used in pass-through mode in a VM (w/embedded f/w).
If host error reading PF num from CN23XX_PCIE_SRIOV_FDL reg,
try to retrieve PF num from SLI_PKT(0)_INPUT_CONTROL (initialized by f/w).
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Sat, 19 Aug 2017 00:14:49 +0000 (17:14 -0700)]
ipv6: repair fib6 tree in failure case
In fib6_add(), it is possible that fib6_add_1() picks an intermediate
node and sets the node's fn->leaf to NULL in order to add this new
route. However, if fib6_add_rt2node() fails to add the new
route for some reason, fn->leaf will be left as NULL and could
potentially cause crash when fn->leaf is accessed in fib6_locate().
This patch makes sure fib6_repair_tree() is called to properly repair
fn->leaf in the above failure case.
Here is the syzkaller reported general protection fault in fib6_locate:
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 0 PID: 40937 Comm: syz-executor3 Not tainted
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
task:
ffff8801d7d64100 ti:
ffff8801d01a0000 task.ti:
ffff8801d01a0000
RIP: 0010:[<
ffffffff82a3e0e1>] [<
ffffffff82a3e0e1>] __ipv6_prefix_equal64_half include/net/ipv6.h:475 [inline]
RIP: 0010:[<
ffffffff82a3e0e1>] [<
ffffffff82a3e0e1>] ipv6_prefix_equal include/net/ipv6.h:492 [inline]
RIP: 0010:[<
ffffffff82a3e0e1>] [<
ffffffff82a3e0e1>] fib6_locate_1 net/ipv6/ip6_fib.c:1210 [inline]
RIP: 0010:[<
ffffffff82a3e0e1>] [<
ffffffff82a3e0e1>] fib6_locate+0x281/0x3c0 net/ipv6/ip6_fib.c:1233
RSP: 0018:
ffff8801d01a36a8 EFLAGS:
00010202
RAX:
0000000000000020 RBX:
ffff8801bc790e00 RCX:
ffffc90002983000
RDX:
0000000000001219 RSI:
ffff8801d01a37a0 RDI:
0000000000000100
RBP:
ffff8801d01a36f0 R08:
00000000000000ff R09:
0000000000000000
R10:
0000000000000003 R11:
0000000000000000 R12:
0000000000000001
R13:
dffffc0000000000 R14:
ffff8801d01a37a0 R15:
0000000000000000
FS:
00007f6afd68c700(0000) GS:
ffff8801db400000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00000000004c6340 CR3:
00000000ba41f000 CR4:
00000000001426f0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Stack:
ffff8801d01a37a8 ffff8801d01a3780 ffffed003a0346f5 0000000c82a23ea0
ffff8800b7bd7700 ffff8801d01a3780 ffff8800b6a1c940 ffffffff82a23ea0
ffff8801d01a3920 ffff8801d01a3748 ffffffff82a223d6 ffff8801d7d64988
Call Trace:
[<
ffffffff82a223d6>] ip6_route_del+0x106/0x570 net/ipv6/route.c:2109
[<
ffffffff82a23f9d>] inet6_rtm_delroute+0xfd/0x100 net/ipv6/route.c:3075
[<
ffffffff82621359>] rtnetlink_rcv_msg+0x549/0x7a0 net/core/rtnetlink.c:3450
[<
ffffffff8274c1d1>] netlink_rcv_skb+0x141/0x370 net/netlink/af_netlink.c:2281
[<
ffffffff82613ddf>] rtnetlink_rcv+0x2f/0x40 net/core/rtnetlink.c:3456
[<
ffffffff8274ad38>] netlink_unicast_kernel net/netlink/af_netlink.c:1206 [inline]
[<
ffffffff8274ad38>] netlink_unicast+0x518/0x750 net/netlink/af_netlink.c:1232
[<
ffffffff8274b83e>] netlink_sendmsg+0x8ce/0xc30 net/netlink/af_netlink.c:1778
[<
ffffffff82564aff>] sock_sendmsg_nosec net/socket.c:609 [inline]
[<
ffffffff82564aff>] sock_sendmsg+0xcf/0x110 net/socket.c:619
[<
ffffffff82564d62>] sock_write_iter+0x222/0x3a0 net/socket.c:834
[<
ffffffff8178523d>] new_sync_write+0x1dd/0x2b0 fs/read_write.c:478
[<
ffffffff817853f4>] __vfs_write+0xe4/0x110 fs/read_write.c:491
[<
ffffffff81786c38>] vfs_write+0x178/0x4b0 fs/read_write.c:538
[<
ffffffff817892a9>] SYSC_write fs/read_write.c:585 [inline]
[<
ffffffff817892a9>] SyS_write+0xd9/0x1b0 fs/read_write.c:577
[<
ffffffff82c71e32>] entry_SYSCALL_64_fastpath+0x12/0x17
Note: there is no "Fixes" tag as this seems to be a bug introduced
very early.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bhumika Goyal [Sat, 19 Aug 2017 10:55:52 +0000 (16:25 +0530)]
net: dsa: mv88e6xxx: make irq_chip const
Make this const as it is only used in a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Konstantin Khlebnikov [Sat, 19 Aug 2017 12:37:07 +0000 (15:37 +0300)]
net_sched: fix order of queue length updates in qdisc_replace()
This important to call qdisc_tree_reduce_backlog() after changing queue
length. Parent qdisc should deactivate class in ->qlen_notify() called from
qdisc_tree_reduce_backlog() but this happens only if qdisc->q.qlen in zero.
Missed class deactivations leads to crashes/warnings at picking packets
from empty qdisc and corrupting state at reactivating this class in future.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Fixes:
86a7996cc8a0 ("net_sched: introduce qdisc_replace() helper")
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe Jaillet [Sun, 20 Aug 2017 04:35:00 +0000 (06:35 +0200)]
net: ibm: emac: Fix some error handling path in 'emac_probe()'
If 'irq_of_parse_and_map()' or 'of_address_to_resource()' fail, 'err' is
known to be 0 at this point.
So return -ENODEV instead in the first case and use 'of_iomap()' instead of
the equivalent 'of_address_to_resource()/ioremap()' combinaison in the 2nd
case.
Doing so, the 'rsrc_regs' field of the 'emac_instance struct' becomes
redundant and is removed.
While at it, turn a 'err != 0' test into an equivalent 'err' to be more
consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Sun, 20 Aug 2017 08:45:51 +0000 (14:15 +0530)]
cxgb4/cxgbvf: Handle 32-bit fw port capabilities
Implement new 32-bit Firmware Port Capabilities in order to
handle new speeds which couldn't be represented in the old 16-bit
Firmware Port Capabilities values.
Based on the original work of Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Leblond [Sun, 20 Aug 2017 19:48:14 +0000 (21:48 +0200)]
tools lib bpf: improve warning
Signed-off-by: Eric Leblond <eric@regit.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Packham [Sun, 20 Aug 2017 20:52:54 +0000 (08:52 +1200)]
switchdev: documentation: minor typo fixes
Two typos in switchdev.txt
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sun, 20 Aug 2017 23:48:12 +0000 (01:48 +0200)]
bpf: fix double free from dev_map_notification()
In the current code, dev_map_free() can still race with dev_map_notification().
In dev_map_free(), we remove dtab from the list of dtabs after we purged
all entries from it. However, we don't do xchg() with NULL or the like,
so the entry at that point is still pointing to the device. If a unregister
notification comes in at the same time, we therefore risk a double-free,
since the pointer is still present in the map, and then pushed again to
__dev_map_entry_free().
All this is completely unnecessary. Just remove the dtab from the list
right before the synchronize_rcu(), so all outstanding readers from the
notifier list have finished by then, thus we don't need to deal with this
corner case anymore and also wouldn't need to nullify dev entires. This is
fine because we iterate over the map releasing all entries and therefore
dev references anyway.
Fixes:
4cc7b9544b9a ("bpf: devmap fix mutex in rcu critical section")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sun, 20 Aug 2017 22:26:03 +0000 (00:26 +0200)]
bpf, doc: also add s390x as arch to sysctl description
Looks like this was accidentally missed, so still add s390x
as supported eBPF JIT arch to bpf_jit_enable.
Fixes:
014cd0a368dc ("bpf: Update sysctl documentation to list all supported architectures")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 20 Aug 2017 22:19:31 +0000 (15:19 -0700)]
Merge tag 'mlx5-updates-2017-08-17-V2' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-08-17
Some updates for mlx5 ethernet and IPoIB device driver.
Eran added the support for manage physical link state from netdevice upon
interface open/close requests.
Feras fixed the driver name showed in ethtool for IPoIB interfaces.
Shalom Added the support for IPoIB netdevice ethtool get link settings.
Gal and Eran exposed new diagnostic counters for outbound PCIe stalls and overflow
and RX buffer fullness statistics.
Code cleanups from Or Gerlitz.
Variable types cleanup from Gal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 20 Aug 2017 21:13:52 +0000 (14:13 -0700)]
Linux 4.13-rc6
Linus Torvalds [Sun, 20 Aug 2017 20:26:27 +0000 (13:26 -0700)]
Sanitize 'move_pages()' permission checks
The 'move_paghes()' system call was introduced long long ago with the
same permission checks as for sending a signal (except using
CAP_SYS_NICE instead of CAP_SYS_KILL for the overriding capability).
That turns out to not be a great choice - while the system call really
only moves physical page allocations around (and you need other
capabilities to do a lot of it), you can check the return value to map
out some the virtual address choices and defeat ASLR of a binary that
still shares your uid.
So change the access checks to the more common 'ptrace_may_access()'
model instead.
This tightens the access checks for the uid, and also effectively
changes the CAP_SYS_NICE check to CAP_SYS_PTRACE, but it's unlikely that
anybody really _uses_ this legacy system call any more (we hav ebetter
NUMA placement models these days), so I expect nobody to notice.
Famous last words.
Reported-by: Otto Ebeling <otto.ebeling@iki.fi>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 20 Aug 2017 16:36:52 +0000 (09:36 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Another pile of small fixes and updates for x86:
- Plug a hole in the SMAP implementation which misses to clear AC on
NMI entry
- Fix the norandmaps/ADDR_NO_RANDOMIZE logic so the command line
parameter works correctly again
- Use the proper accessor in the startup64 code for next_early_pgt to
prevent accessing of invalid addresses and faulting in the early
boot code.
- Prevent CPU hotplug lock recursion in the MTRR code
- Unbreak CPU0 hotplugging
- Rename overly long CPUID bits which got introduced in this cycle
- Two commits which mark data 'const' and restrict the scope of data
and functions to file scope by making them 'static'"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Constify attribute_group structures
x86/boot/64/clang: Use fixup_pointer() to access 'next_early_pgt'
x86/elf: Remove the unnecessary ADDR_NO_RANDOMIZE checks
x86: Fix norandmaps/ADDR_NO_RANDOMIZE
x86/mtrr: Prevent CPU hotplug lock recursion
x86: Mark various structures and functions as 'static'
x86/cpufeature, kvm/svm: Rename (shorten) the new "virtualized VMSAVE/VMLOAD" CPUID flag
x86/smpboot: Unbreak CPU0 hotplug
x86/asm/64: Clear AC on NMI entries
Linus Torvalds [Sun, 20 Aug 2017 16:34:24 +0000 (09:34 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A few small fixes for timer drivers:
- Prevent infinite recursion in the arm architected timer driver with
ftrace
- Propagate error codes to the caller in case of failure in EM STI
driver
- Adjust a bogus loop iteration in the arm architected timer driver
- Add a missing Kconfig dependency to the pistachio clocksource to
prevent build failures
- Correctly check for IS_ERR() instead of NULL in the shared timer-of
code"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/arm_arch_timer: Avoid infinite recursion when ftrace is enabled
clocksource/drivers/Kconfig: Fix CLKSRC_PISTACHIO dependencies
clocksource/drivers/timer-of: Checking for IS_ERR() instead of NULL
clocksource/drivers/em_sti: Fix error return codes in em_sti_probe()
clocksource/drivers/arm_arch_timer: Fix mem frame loop initialization
Linus Torvalds [Sun, 20 Aug 2017 16:20:57 +0000 (09:20 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"Two fixes for the perf subsystem:
- Fix an inconsistency of RDPMC mm struct tagging across exec() which
causes RDPMC to fault.
- Correct the timestamp mechanics across IOC_DISABLE/ENABLE which
causes incorrect timestamps and total time calculations"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix time on IOC_ENABLE
perf/x86: Fix RDPMC vs. mm_struct tracking
Linus Torvalds [Sun, 20 Aug 2017 16:07:56 +0000 (09:07 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A pile of smallish changes all over the place:
- Add a missing ISB in the GIC V1 driver
- Remove an ACPI version check in the GIC V3 ITS driver
- Add the missing irq_pm_shutdown function for BRCMSTB-L2 to avoid
spurious wakeups
- Remove the artifical limitation of ITS instances to the number of
NUMA nodes which prevents utilizing the ITS hardware correctly
- Prevent a infinite parsing loop in the GIC-V3 ITS/MSI code
- Honour the force affinity argument in the GIC-V3 driver which is
required to make perf work correctly
- Correctly report allocation failures in GIC-V2/V3 to avoid using
half allocated and initialized interrupts.
- Fixup checks against nr_cpu_ids in the generic IPI code"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/ipi: Fixup checks against nr_cpu_ids
genirq: Restore trigger settings in irq_modify_status()
MAINTAINERS: Remove Jason Cooper's irqchip git tree
irqchip/gic-v3-its-platform-msi: Fix msi-parent parsing loop
irqchip/gic-v3-its: Allow GIC ITS number more than MAX_NUMNODES
irqchip: brcmstb-l2: Define an irq_pm_shutdown function
irqchip/gic: Ensure we have an ISB between ack and ->handle_irq
irqchip/gic-v3-its: Remove ACPICA version check for ACPI NUMA
irqchip/gic-v3: Honor forced affinity setting
irqchip/gic-v3: Report failures in gic_irq_domain_alloc
irqchip/gic-v2: Report failures in gic_irq_domain_alloc
irqchip/atmel-aic: Remove root argument from ->fixup() prototype
irqchip/atmel-aic: Fix unbalanced refcount in aic_common_rtc_irq_fixup()
irqchip/atmel-aic: Fix unbalanced of_node_put() in aic_common_irq_fixup()
Linus Torvalds [Sun, 20 Aug 2017 15:54:30 +0000 (08:54 -0700)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull watchdog fix from Thomas Gleixner:
"A fix for the hardlockup watchdog to prevent false positives with
extreme Turbo-Modes which make the perf/NMI watchdog fire faster than
the hrtimer which is used to verify.
Slightly larger than the minimal fix, which just would increase the
hrtimer frequency, but comes with extra overhead of more watchdog
timer interrupts and thread wakeups for all users.
With this change we restrict the overhead to the extreme Turbo-Mode
systems"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kernel/watchdog: Prevent false positives with turbo modes
Gal Pressman [Sun, 2 Jul 2017 15:26:21 +0000 (18:26 +0300)]
net/mlx5e: Use size_t to store byte offset in statistics descriptors
The byte offset of counter descriptors should be stored in size_t variable
instead of an integer.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Gal Pressman [Wed, 28 Jun 2017 11:03:36 +0000 (14:03 +0300)]
net/mlx5e: Use kernel types instead of uint*_t in ethtool callbacks
Fix checkpatch errors:
CHECK:PREFER_KERNEL_TYPES: Prefer kernel type 'u32' over 'uint32_t'
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Or Gerlitz [Tue, 11 Jul 2017 13:10:50 +0000 (16:10 +0300)]
net/mlx5e: Place constants on the right side of comparisons
To fix these checkpatch complaints:
WARNING: Comparisons should place the constant on the right side of the test
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Or Gerlitz [Tue, 11 Jul 2017 12:40:30 +0000 (15:40 +0300)]
net/mlx5e: Avoid using multiple blank lines
To fix these checkpatch complaints:
CHECK: Please don't use multiple blank lines
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Or Gerlitz [Tue, 11 Jul 2017 12:36:11 +0000 (15:36 +0300)]
net/mlx5e: Properly indent within conditional statements
To fix these checkpatch complaints:
WARNING: suspect code indent for conditional statements (8, 24)
+ if (eth_proto & (MLX5E_PROT_MASK(MLX5E_10GBASE_SR)
[...]
+ return PORT_FIBRE;
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Or Gerlitz [Tue, 11 Jul 2017 12:53:29 +0000 (15:53 +0300)]
net/mlx5: Add a blank line after declarations
To fix these checkpatch complaints:
WARNING: Missing a blank line after declarations
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Or Gerlitz [Tue, 11 Jul 2017 12:44:04 +0000 (15:44 +0300)]
net/mlx5: Avoid blank lines after/before open/close brace
To fix these checkpatch complaints:
CHECK: Blank lines aren't necessary after an open brace '{'
CHECK: Blank lines aren't necessary before a close brace '}'
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eran Ben Elisha [Thu, 11 May 2017 23:47:02 +0000 (02:47 +0300)]
net/mlx5e: Add outbound PCI buffer overflow counter
Add outbound_pci_buffer_overflow to ethtool output for monitoring the
number of packets that were dropped due to lack of PCIe buffers on
receive path from NIC port toward the host(s).
This counter is valid only in case that tx_overflow_buffer_pkt is
supported in MCAM enhanced features.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Gal Pressman [Sun, 18 Jun 2017 11:56:57 +0000 (14:56 +0300)]
net/mlx5e: Add RX buffer fullness counters
rx_buffer_passed_thres_phy - The number of events where the port RX
buffer has passed a fullness threshold.
rx_buffer_full_phy - The number of events where the port RX buffer has
reached 100% fullness.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Gal Pressman [Sun, 18 Jun 2017 11:56:45 +0000 (14:56 +0300)]
net/mlx5: Add RX buffer fullness counters infrastructure
Add capability bit in PCAM register and counters to PPCNT register.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Gal Pressman [Thu, 15 Jun 2017 15:29:32 +0000 (18:29 +0300)]
net/mlx5e: Add PCIe outbound stalls counters
outbound_pci_stalled_rd - The percentage of time within the last second
that the NIC had outbound non-posted read requests but could not perform
the operation due to insufficient non-posted credits.
outbound_pci_stalled_wr - The percentage of time within the
last second that the NIC had outbound posted writes requests but could
not perform the operation due to insufficient posted credits.
outbound_pci_stalled_rd_events - The number of events where
outbound_pci_stalled_rd was above the threshold.
outbound_pci_stalled_wr_events - The number of events where
outbound_pci_stalled_wr was above the threshold.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Gal Pressman [Thu, 15 Jun 2017 15:29:23 +0000 (18:29 +0300)]
net/mlx5: Add PCIe outbound stalls counters infrastructure
Add capability bit in MCAM register and counters to MPCNT register.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Shalom Lagziel [Sun, 28 May 2017 13:40:24 +0000 (16:40 +0300)]
net/mlx5e: IPoIB, Add support for get_link_ksettings in ethtool
Add support for "ethtool DEVNAME" over ipoib ports,
Display standard port information for IPoIB netdevices using ethtool
For example:
$ ethtool ib2
> Settings for ib2:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Speed: 100000Mb/s
Duplex: Full
Port: Other
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
Link detected: yes
Signed-off-by: Shalom Lagziel <shaloml@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Feras Daoud [Mon, 10 Jul 2017 15:35:06 +0000 (18:35 +0300)]
net/mlx5e: IPoIB, Fix driver name retrieved by ethtool
Printing an enhanced IPoIB device information using
"ethtool -i DEVNAME", prints the low level driver name: mlx5_core.
This commit changes the name to mlx5_core [ib_ipoib], to include the
ipoib device driver infromation.
Fixes:
076b0936e5fb ("net/mlx5e: IPoIB, Add ethtool support")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>