OSDN Git Service
Shengjiu Wang [Fri, 12 Mar 2021 02:38:45 +0000 (10:38 +0800)]
ASoC: imx-rpmsg: Add machine driver for audio base on rpmsg
The platform device is not registered by device tree or
cpu dai driver, it is registered by the rpmsg channel,
So add a dedicated machine driver to handle this case.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1615516725-4975-7-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shengjiu Wang [Fri, 12 Mar 2021 02:38:44 +0000 (10:38 +0800)]
ASoC: imx-pcm-rpmsg: Add platform driver for audio base on rpmsg
Platform driver based on rpmsg is the interface for sending and
receiving rpmsg to and from M core. It will tell the Cortex-M core
sound format/rate/channel, where is the data buffer, where is
the period size, when to start, when to stop and when suspend
or resume happen, each this behavior there is defined rpmsg
command.
Especially we designed the low power audio case, that is to
allocate a large buffer and fill the data, then Cortex-A core can go
to sleep mode, Cortex-M core continue to play the sound, when the
buffer is consumed, Cortex-M core will trigger the Cortex-A core to
wake up.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1615516725-4975-6-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shengjiu Wang [Fri, 12 Mar 2021 02:38:43 +0000 (10:38 +0800)]
ASoC: imx-audio-rpmsg: Add rpmsg_driver for audio channel
This driver is used to accept the message from rpmsg audio
channel, and if this driver is probed, it will help to register
the platform driver, the platform driver will use this
audio channel to send and receive messages to and from Cortex-M
core.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1615516725-4975-5-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shengjiu Wang [Fri, 12 Mar 2021 02:38:42 +0000 (10:38 +0800)]
ASoC: dt-bindings: fsl_rpmsg: Add binding doc for rpmsg audio device
fsl_rpmsg is a virtual audio device. Mapping to real hardware
devices are SAI, DMA controlled by Cortex M core. What we see from
Linux side is a device which provides audio service by rpmsg channel.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1615516725-4975-4-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shengjiu Wang [Fri, 12 Mar 2021 02:38:41 +0000 (10:38 +0800)]
ASoC: fsl_rpmsg: Add CPU DAI driver for audio base on rpmsg
This is a cpu dai driver for rpmsg audio use case,
which is mainly used for getting the user's configuration
from devicetree and configure the clocks which is used by
Cortex-M core.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1615516725-4975-3-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shengjiu Wang [Fri, 12 Mar 2021 02:38:40 +0000 (10:38 +0800)]
ASoC: soc-component: Add snd_soc_pcm_component_ack
Add snd_soc_pcm_component_ack back, which can be used to get an
updated buffer pointer in the platform driver.
On Asymmetric multiprocessor, this pointer can be sent to Cortex-M
core for audio processing.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1615516725-4975-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Wed, 24 Mar 2021 23:29:33 +0000 (23:29 +0000)]
Merge series "MFD/extcon/ASoC: Rework arizona codec jack-detect support" from Hans de Goede <hdegoede@redhat.com>:
Hi All,
Here is v4 of my series to rework the arizona codec jack-detect support
to use the snd_soc_jack helpers instead of direct extcon reporting.
As discussed before here is a resend rebased on 5.12-rc2, making sure that
all patches this depends on are in place.
Lee, can you pick-up patches 1-6 through the MFD tree and then send a
pull-req to Mark so that Mark can merge the Asoc parts throught the ASoC
tree ?
Patches 2-6 touch drivers/extcon, these all have an Ack from Chanwoo Choi
for merging these through the MFD tree.
Here is some more generic info on this series from the previous
cover-letter:
This is done by reworking the extcon driver into an arizona-jackdet
library and then modifying the codec drivers to use that directly,
replacing the old separate extcon child-devices and extcon-driver.
This brings the arizona-codec jack-detect handling inline with how
all other ASoC codec driver do this. This was developed and tested on
a Lenovo Yoga Tablet 1051L with a WM5102 codec.
This was also tested by Charles Keepax, one of the Cirrus Codec folks.
Regards,
Hans
Hans de Goede (13):
mfd: arizona: Drop arizona-extcon cells
extcon: arizona: Fix some issues when HPDET IRQ fires after the jack
has been unplugged
extcon: arizona: Fix various races on driver unbind
extcon: arizona: Fix flags parameter to the gpiod_get("wlf,micd-pol")
call
extcon: arizona: Always use pm_runtime_get_sync() when we need the
device to be awake
ASoC/extcon: arizona: Move arizona jack code to
sound/soc/codecs/arizona-jack.c
ASoC: arizona-jack: Move jack-detect variables to struct arizona_priv
ASoC: arizona-jack: Use arizona->dev for runtime-pm
ASoC: arizona-jack: convert into a helper library for codec drivers
ASoC: arizona-jack: Use snd_soc_jack to report jack events
ASoC: arizona-jack: Cleanup logging
ASoC: arizona: Make the wm5102, wm5110, wm8997 and wm8998 drivers use
the new jack library
ASoC: Intel: bytcr_wm5102: Add jack detect support
MAINTAINERS | 3 +-
drivers/extcon/Kconfig | 8 -
drivers/extcon/Makefile | 1 -
drivers/mfd/arizona-core.c | 20 -
sound/soc/codecs/Makefile | 2 +-
.../soc/codecs/arizona-jack.c | 577 +++++++-----------
sound/soc/codecs/arizona.h | 44 ++
sound/soc/codecs/wm5102.c | 12 +-
sound/soc/codecs/wm5110.c | 12 +-
sound/soc/codecs/wm8997.c | 14 +-
sound/soc/codecs/wm8998.c | 9 +
sound/soc/intel/boards/bytcr_wm5102.c | 28 +-
12 files changed, 325 insertions(+), 405 deletions(-)
rename drivers/extcon/extcon-arizona.c => sound/soc/codecs/arizona-jack.c (76%)
--
2.30.1
Hans de Goede [Sun, 7 Mar 2021 15:18:07 +0000 (16:18 +0100)]
ASoC: Intel: bytcr_wm5102: Add jack detect support
Add jack detect support by creating a jack and calling
snd_soc_component_set_jack to register the created jack
with the codec.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307151807.35201-14-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hans de Goede [Sun, 7 Mar 2021 15:18:06 +0000 (16:18 +0100)]
ASoC: arizona: Make the wm5102, wm5110, wm8997 and wm8998 drivers use the new jack library
Make all arizona codec drivers for which drivers/mfd/arizona-core.c used
to instantiate a "arizona-extcon" child-device use the new arizona-jack.c
library for jack-detection.
This has been tested on a Lenovo Yoga Tablet 2 1051L with a WM5102 codec.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307151807.35201-13-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hans de Goede [Sun, 7 Mar 2021 15:18:05 +0000 (16:18 +0100)]
ASoC: arizona-jack: Cleanup logging
Cleanup the use of dev_foo functions used for logging:
1. Many of these are unnecessarily split over multiple lines
2. Use dev_err_probe() in cases where we might get a -EPROBE_DEFER
return value
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307151807.35201-12-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hans de Goede [Sun, 7 Mar 2021 15:18:04 +0000 (16:18 +0100)]
ASoC: arizona-jack: Use snd_soc_jack to report jack events
Use the snd_soc_jack code to report jack events, instead of using extcon
for reporting the cable-type + an input_dev for reporting the button
presses.
The snd_soc_jack code will report the cable-type through both input_dev
events and through ALSA controls and the button-presses through input_dev
events.
Note that this means that when the codec drivers are moved over to use
the new arizona-jack.c library code instead of having a separate MFD
extcon cell with the extcon-arizona.c driver, we will no longer report
extcon events to userspace for cable-type changes. This should not be
a problem since "standard" Linux distro userspace does not (and has
never) used the extcon class interface for this. Android does have
support for the extcon class interface, but that was introduced in
the same release as support for input_dev cable-type events, so this
should not be a problem for Android either.
Note this also reduces ARIZONA_MAX_MICD_RANGE from 8 to 6, this is
ok to do since this info is always provided through pdata (or defaults)
and cannot be overridden from devicetree. All in-kernel users of the
pdata (and the fallback defaults) define 6 or less buttons/ranges.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307151807.35201-11-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hans de Goede [Sun, 7 Mar 2021 15:18:03 +0000 (16:18 +0100)]
ASoC: arizona-jack: convert into a helper library for codec drivers
Convert the arizona extcon driver into a helper library for direct use
from the arizona codec-drivers, rather then being bound to a separate
MFD cell.
Note the probe (and remove) sequence is split into 2 parts:
1. The arizona_jack_codec_dev_probe() function inits a bunch of
jack-detect specific variables in struct arizona_priv and tries to get
a number of resources where getting them may fail with -EPROBE_DEFER.
2. Then once the machine driver has create a snd_sock_jack through
snd_soc_card_jack_new() it calls snd_soc_component_set_jack() on
the codec component, which will call the new arizona_jack_set_jack(),
which sets up jack-detection and requests the IRQs.
This split is necessary, because the IRQ handlers need access to the
arizona->dapm pointer and the snd_sock_jack which are not available
when the codec-driver's probe function runs.
Note this requires that machine-drivers for codecs which are converted
to use the new helper functions from arizona-jack.c are modified to
create a snd_soc_jack through snd_soc_card_jack_new() and register
this jack with the codec through snd_soc_component_set_jack().
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307151807.35201-10-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hans de Goede [Sun, 7 Mar 2021 15:18:02 +0000 (16:18 +0100)]
ASoC: arizona-jack: Use arizona->dev for runtime-pm
Drivers for MFD child-devices such as the arizona codec drivers
and the arizona-extcon driver can choose to either make
runtime_pm_get/_put calls on their own child-device, which will
then be propagated to their parent; or they can make them directly
on their MFD parent-device.
The arizona-extcon code was using runtime_pm_get/_put calls on
its own child-device where as the codec drivers are using
runtime_pm_get/_put calls on their parent.
The arizona-extcon MFD cell/child-device has been removed and this
commit is part of refactoring the arizona-extcon code into a library
to be used directly from the codec drivers.
Specifically this commit moves the code over to make
runtime_pm_get/_put calls on the parent device (on arizona->dev)
bringing the code inline with how the codec drivers do this.
Note this also removes the pm_runtime_enable/_disable calls
as pm_runtime support has already been enabled on the parent-device
by the arizona MFD driver.
This is part of a patch series converting the arizona extcon driver into
a helper library for letting the arizona codec-drivers directly report
jack state through the standard sound/soc/soc-jack.c functions.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307151807.35201-9-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hans de Goede [Sun, 7 Mar 2021 15:18:01 +0000 (16:18 +0100)]
ASoC: arizona-jack: Move jack-detect variables to struct arizona_priv
Move all the jack-detect variables from struct arizona_extcon_info to
struct arizona_priv.
This is part of a patch series converting the arizona extcon driver into
a helper library for letting the arizona codec-drivers directly report jack
state through the standard sound/soc/soc-jack.c functions.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307151807.35201-8-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shengjiu Wang [Wed, 24 Mar 2021 09:58:48 +0000 (17:58 +0800)]
ASoC: fsl_micfil: Don't use devm_regmap_init_mmio_clk
When there is power domain bind with ipg_clk clock,
The call flow:
devm_regmap_init_mmio_clk
- clk_prepare()
- clk_pm_runtime_get()
cause the power domain of clock always be enabled after
regmap_init(). which impact the power consumption.
So use devm_regmap_init_mmio instead of
devm_regmap_init_mmio_clk,but explicitly enable
clock when it is used.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Viorel Suman <viorel.suman@nxp.com>
Link: https://lore.kernel.org/r/1616579928-22428-7-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shengjiu Wang [Wed, 24 Mar 2021 09:58:47 +0000 (17:58 +0800)]
ASoC: fsl_audmix: Don't use devm_regmap_init_mmio_clk
When there is power domain bind with ipg clock,
The call flow:
devm_regmap_init_mmio_clk
- clk_prepare()
- clk_pm_runtime_get()
cause the power domain of clock always be enabled after
regmap_init(). which impact the power consumption.
So use devm_regmap_init_mmio instead of
devm_regmap_init_mmio_clk,but explicitly enable
clock when it is used.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1616579928-22428-6-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shengjiu Wang [Wed, 24 Mar 2021 09:58:46 +0000 (17:58 +0800)]
ASoC: fsl_easrc: Don't use devm_regmap_init_mmio_clk
When there is power domain bind with mem clock,
The call flow:
devm_regmap_init_mmio_clk
- clk_prepare()
- clk_pm_runtime_get()
cause the power domain of clock always be enabled after
regmap_init(). which impact the power consumption.
So use devm_regmap_init_mmio instead of
devm_regmap_init_mmio_clk,but explicitly enable
clock when it is used.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1616579928-22428-5-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shengjiu Wang [Wed, 24 Mar 2021 09:58:45 +0000 (17:58 +0800)]
ASoC: fsl_asrc: Don't use devm_regmap_init_mmio_clk
When there is power domain bind with mem clock,
The call flow:
devm_regmap_init_mmio_clk
- clk_prepare()
- clk_pm_runtime_get()
cause the power domain of clock always be enabled after
regmap_init(). which impact the power consumption.
So use devm_regmap_init_mmio instead of
devm_regmap_init_mmio_clk,but explicitly enable
clock when it is used.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1616579928-22428-4-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shengjiu Wang [Wed, 24 Mar 2021 09:58:44 +0000 (17:58 +0800)]
ASoC: fsl_spdif: Don't use devm_regmap_init_mmio_clk
When there is power domain bind with core clock,
The call flow:
devm_regmap_init_mmio_clk
- clk_prepare()
- clk_pm_runtime_get()
cause the power domain of clock always be enabled after
regmap_init(). which impact the power consumption.
So use devm_regmap_init_mmio instead of
devm_regmap_init_mmio_clk,but explicitly enable
clock when it is used.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1616579928-22428-3-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shengjiu Wang [Wed, 24 Mar 2021 09:58:43 +0000 (17:58 +0800)]
ASoC: fsl_esai: Don't use devm_regmap_init_mmio_clk
When there is power domain bind with bus clock,
The call flow:
devm_regmap_init_mmio_clk
- clk_prepare()
- clk_pm_runtime_get()
cause the power domain of clock always be enabled after
regmap_init(). which impact the power consumption.
So use devm_regmap_init_mmio instead of
devm_regmap_init_mmio_clk,but explicitly enable
clock when it is used.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1616579928-22428-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Tue, 23 Mar 2021 22:13:35 +0000 (22:13 +0000)]
Merge tag 'ib-mfd-extcon-v5.13' of git://git./linux/kernel/git/lee/mfd into asoc-5.13
Immutable branch between MFD and Extcon due for the v5.13 merge window
Kai Vehmanen [Mon, 22 Mar 2021 14:38:30 +0000 (16:38 +0200)]
ASoC: SOF: Intel: hda: drop display power on/off in D0i3 flows
Controller needs to ensure display power is enabled only for
HDA controller reset. Drop the display power-up/down calls from
D0i3 entry/exit paths.
This was previously not possible as codec drivers could not resume the
links, and instead controller kept the reference to display power. The
state of display power had be maintained in the D0i3 entry/exit code.
With commit
87fc20e4a0cb ("ASoC: SOF: Intel: hda: use hdac_ext
fine-grained link management"), this is no longer needed and the code
can be cleaned up.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Keyon Jie <yang.jie@intel.com>
Link: https://lore.kernel.org/r/20210322143830.3880293-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Keyon Jie [Fri, 19 Mar 2021 12:49:50 +0000 (14:49 +0200)]
ASoC: intel: sof_rt5682: use the topology mclk
We should use the topology configured mclk if it existed, which can make
sure we are aligned with the FW side about the mclk usage.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210319124950.3853994-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Keyon Jie [Fri, 19 Mar 2021 12:49:49 +0000 (14:49 +0200)]
ASoC: SOF: add a helper to get topology configured mclk
Add helper sof_dai_ssp_mclk to get the topology configured MCLK from a
pcm_runtime, return 0 if it is not available, and error if the dai type
is not SSP at the moment.
Export the helper for external use, e.g. from machine drivers.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210319124950.3853994-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shengjiu Wang [Fri, 19 Mar 2021 08:06:43 +0000 (16:06 +0800)]
ASoC: fsl_sai: Don't use devm_regmap_init_mmio_clk
When there is power domain bind with bus clock,
The call flow:
devm_regmap_init_mmio_clk
- clk_prepare()
- clk_pm_runtime_get()
cause the power domain of clock always be enabled after
regmap_init(). which impact the power consumption.
So use devm_regmap_init_mmio instead of
devm_regmap_init_mmio_clk, then explicitly enable clock when
using by pm_runtime_get(), if CONFIG_PM=n, then
fsl_sai_runtime_resume will be explicitly called.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Link: https://lore.kernel.org/r/1616141203-13344-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vijendar Mukunda [Fri, 19 Mar 2021 01:40:42 +0000 (07:10 +0530)]
ASoC: amd: Add support for RT5682 codec in machine driver
Add support for RT5682 codec in machine driver.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/1616118056-5506-1-git-send-email-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Fri, 19 Mar 2021 16:31:39 +0000 (16:31 +0000)]
Merge series "ASoC: tidyup error message timing" from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:
Hi Mark
Indicating error message when failed case is very useful for debuging.
In many case, it uses below style.
int function(...)
{
...
return ret;
}
int caller(...)
{
...
ret = function(...);
if (ret < 0)
dev_err(...)
...
}
This is not so bad, but in this style *each caller* needs to indicate
duplicate same error message, and some caller is forgetting to do it.
And caller can't indicate detail function() error information.
I know many people have many opinion, but if function() indicates error
message, we can get same and detail information without forgot, and it is better.
This patch-set tidyup to do it.
int function(...)
{
...
if (ret < 0)
dev_err(...)
return ret;
}
int caller(...)
{
...
ret = function(...);
...
}
Kuninori Morimoto (14):
ASoC: soc-pcm: indicate error message at soc_pcm_open()
ASoC: soc-pcm: indicate error message at soc_pcm_hw_params()
ASoC: soc-pcm: indicate error message at soc_pcm_prepare()
ASoC: soc-pcm: indicate error message at dpcm_path_get()
ASoC: soc-pcm: indicate error message at dpcm_be_dai_trigger()
ASoC: soc-pcm: indicate error message at dpcm_apply_symmetry()
ASoC: soc-pcm: indicate error message at dpcm_run_update_startup/shutdown()
ASoC: soc-pcm: indicate error message at dpcm_fe/be_dai_startup()
ASoC: soc-pcm: indicate error message at dpcm_fe/be_dai_hw_params()
ASoC: soc-pcm: indicate error message at dpcm_fe/be_dai_prepare()
ASoC: soc-pcm: don't indicate error message for soc_pcm_hw_free()
ASoC: soc-pcm: don't indicate error message for dpcm_be_dai_hw_free()
ASoC: don't indicate error message for snd_soc_[pcm_]dai_xxx()
ASoC: don't indicate error message for snd_soc_[pcm_]component_xxx()
include/sound/soc-dpcm.h | 2 +-
sound/soc/soc-compress.c | 9 +-
sound/soc/soc-core.c | 22 +----
sound/soc/soc-dapm.c | 24 ++---
sound/soc/soc-pcm.c | 197 +++++++++++++++++++--------------------
5 files changed, 108 insertions(+), 146 deletions(-)
--
2.25.1
Wei Yongjun [Fri, 19 Mar 2021 09:41:02 +0000 (09:41 +0000)]
ASoC: rt1019: make symbol 'rt1019_i2c_driver' static
The sparse tool complains as follows:
sound/soc/codecs/rt1019.c:927:19: warning:
symbol 'rt1019_i2c_driver' was not declared. Should it be static?
This symbol is not used outside of rt1019.c, so this
commit marks it static.
Fixes:
7ec79d3850d0 ("ASoC: rt1019: add rt1019 amplifier driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210319094102.4185096-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuninori Morimoto [Mon, 15 Mar 2021 00:58:41 +0000 (09:58 +0900)]
ASoC: don't indicate error message for snd_soc_[pcm_]component_xxx()
All snd_soc_component_xxx() and snd_soc_pcm_component_xxx() itself
indicate error message if failed.
Its caller doesn't need to indicate duplicated error message.
This patch removes it.
All snd_soc_component_xxx() indicate error message if failed.
Its caller doesn't need to indicate duplicated error message.
This patch removes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/878s6puta6.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuninori Morimoto [Mon, 15 Mar 2021 00:58:37 +0000 (09:58 +0900)]
ASoC: don't indicate error message for snd_soc_[pcm_]dai_xxx()
All snd_soc_dai_xxx() and snd_soc_pcm_dai_xxx() itself
indicate error message if failed.
Its caller doesn't need to indicate duplicated error message.
This patch removes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87a6r5utaa.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuninori Morimoto [Mon, 15 Mar 2021 00:58:32 +0000 (09:58 +0900)]
ASoC: soc-pcm: don't indicate error message for dpcm_be_dai_hw_free()
dpcm_be_dai_hw_free() never fail, error message is not needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87blblutaf.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuninori Morimoto [Mon, 15 Mar 2021 00:58:28 +0000 (09:58 +0900)]
ASoC: soc-pcm: don't indicate error message for soc_pcm_hw_free()
soc_pcm_hw_free() never fail, error message is not needed.
We can't use void function for it, because it is used
part of struct snd_pcm_ops :: hw_free.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87czw1utaj.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuninori Morimoto [Mon, 15 Mar 2021 00:58:22 +0000 (09:58 +0900)]
ASoC: soc-pcm: indicate error message at dpcm_fe/be_dai_prepare()
Indicating error message when failed case is very useful for debuging.
In many case, its style is like below.
int function(...)
{
...
return ret;
}
int caller(...)
{
...
ret = function(...);
if (ret < 0)
dev_err(...)
...
}
This is not so bad, but in this style *each caller* needs to indicate
duplicate same error message, and some caller is forgetting to do it.
And caller can't indicate detail function() error information.
If function() indicates error message, we can get same and
detail information without forgot.
int function(...)
{
...
if (ret < 0)
dev_err(...)
return ret;
}
int caller(...)
{
...
ret = function(...);
...
}
This patch follow above style at dpcm_fe/be_dai_prepare()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87eeghutap.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuninori Morimoto [Mon, 15 Mar 2021 00:58:18 +0000 (09:58 +0900)]
ASoC: soc-pcm: indicate error message at dpcm_fe/be_dai_hw_params()
Indicating error message when failed case is very useful for debuging.
In many case, its style is like below.
int function(...)
{
...
return ret;
}
int caller(...)
{
...
ret = function(...);
if (ret < 0)
dev_err(...)
...
}
This is not so bad, but in this style *each caller* needs to indicate
duplicate same error message, and some caller is forgetting to do it.
And caller can't indicate detail function() error information.
If function() indicates error message, we can get same and
detail information without forgot.
int function(...)
{
...
if (ret < 0)
dev_err(...)
return ret;
}
int caller(...)
{
...
ret = function(...);
...
}
This patch follow above style at dpcm_fe/be_dai_hw_params()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87ft0xutat.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuninori Morimoto [Mon, 15 Mar 2021 00:58:13 +0000 (09:58 +0900)]
ASoC: soc-pcm: indicate error message at dpcm_fe/be_dai_startup()
Indicating error message when failed case is very useful for debuging.
In many case, its style is like below.
int function(...)
{
...
return ret;
}
int caller(...)
{
...
ret = function(...);
if (ret < 0)
dev_err(...)
...
}
This is not so bad, but in this style *each caller* needs to indicate
duplicate same error message, and some caller is forgetting to do it.
And caller can't indicate detail function() error information.
If function() indicates error message, we can get same and
detail information without forgot.
int function(...)
{
...
if (ret < 0)
dev_err(...)
return ret;
}
int caller(...)
{
...
ret = function(...);
...
}
This patch follow above style at dpcm_fe/be_dai_startup().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87h7ldutay.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuninori Morimoto [Mon, 15 Mar 2021 00:58:08 +0000 (09:58 +0900)]
ASoC: soc-pcm: indicate error message at dpcm_run_update_startup/shutdown()
Indicating error message when failed case is very useful for debuging.
In many case, its style is like below.
int function(...)
{
...
return ret;
}
int caller(...)
{
...
ret = function(...);
if (ret < 0)
dev_err(...)
...
}
This is not so bad, but in this style *each caller* needs to indicate
duplicate same error message, and some caller is forgetting to do it.
And caller can't indicate detail function() error information.
If function() indicates error message, we can get same and
detail information without forgot.
int function(...)
{
...
if (ret < 0)
dev_err(...)
return ret;
}
int caller(...)
{
...
ret = function(...);
...
}
This patch also
do below to dpcm_run_update_startup()
1) remove duplicated ret = -EINVAL
2) remove blank line
do below to dpcm_run_update_shutdown()
1) remove unused ret
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87im5tutb3.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuninori Morimoto [Mon, 15 Mar 2021 00:58:02 +0000 (09:58 +0900)]
ASoC: soc-pcm: indicate error message at dpcm_apply_symmetry()
Indicating error message when failed case is very useful for debuging.
In many case, its style is like below.
int function(...)
{
...
return ret;
}
int caller(...)
{
...
ret = function(...);
if (ret < 0)
dev_err(...)
...
}
This is not so bad, but in this style *each caller* needs to indicate
duplicate same error message, and some caller is forgetting to do it.
And caller can't indicate detail function() error information.
If function() indicates error message, we can get same and
detail information without forgot.
int function(...)
{
...
if (ret < 0)
dev_err(...)
return ret;
}
int caller(...)
{
...
ret = function(...);
...
}
This patch follow above style at dpcm_apply_symmetry(...)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87k0q9utb9.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuninori Morimoto [Mon, 15 Mar 2021 00:57:57 +0000 (09:57 +0900)]
ASoC: soc-pcm: indicate error message at dpcm_be_dai_trigger()
Indicating error message when failed case is very useful for debuging.
In many case, its style is like below.
int function(...)
{
...
return ret;
}
int caller(...)
{
...
ret = function(...);
if (ret < 0)
dev_err(...)
...
}
This is not so bad, but in this style *each caller* needs to indicate
duplicate same error message, and some caller is forgetting to do it.
And caller can't indicate detail function() error information.
If function() indicates error message, we can get same and
detail information without forgot.
int function(...)
{
...
if (ret < 0)
dev_err(...)
return ret;
}
int caller(...)
{
...
ret = function(...);
...
}
Now, dpcm_be_dai_trigger() user uses it like below.
err = dpcm_be_dai_trigger(...);
if (err < 0)
dev_err(..., "ASoC: trigger FE failed %d\n", err);
But we can get more detail information if dpcm_be_dai_trigger() itself
had dev_err(). And above error message is confusable,
failed is *BE*, not *FE*.
This patch indicates error message at dpcm_be_dai_trigger().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87lfaputbe.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuninori Morimoto [Mon, 15 Mar 2021 00:57:52 +0000 (09:57 +0900)]
ASoC: soc-pcm: indicate error message at dpcm_path_get()
Indicating error message when failed case is very useful for debuging.
In many case, its style is like below.
int function(...)
{
...
return ret;
}
int caller(...)
{
...
ret = function(...);
if (ret < 0)
dev_err(...)
...
}
This is not so bad, but in this style *each caller* needs to indicate
duplicate same error message, and some caller is forgetting to do it.
And caller can't indicate detail function() error information.
If function() indicates error message, we can get same and
detail information without forgot.
int function(...)
{
...
if (ret < 0)
dev_err(...)
return ret;
}
int caller(...)
{
...
ret = function(...);
...
}
Now, many place uses dpcm_path_get() like below
ret = dpcm_path_get(...);
if (ret < 0)
goto error;
(A) else if (ret == 0)
dev_dbg(...)
But here, (A) part can be indicated at dpcm_path_get() not caller.
It is simple and readable code.
This patch do it.
Small detail behaviors will be exchanged by this patch.
1) indicates debug info (= path numbers) if path > 0 case only
(It was *always* indicated).
2) soc_dpcm_fe_runtime_update() is indicating error message
for paths < 0 case, but it is already done at dpcm_path_get().
Thus just remove it. but dev_dbg() vs dev_warn() is exchanged.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87mtv5utbj.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuninori Morimoto [Mon, 15 Mar 2021 00:57:48 +0000 (09:57 +0900)]
ASoC: soc-pcm: indicate error message at soc_pcm_prepare()
Indicating error message when failed case is very useful for debuging.
In many case, its style is like below.
int function(...)
{
...
return ret;
}
int caller(...)
{
...
ret = function(...);
if (ret < 0)
dev_err(...)
...
}
This is not so bad, but in this style *each caller* needs to indicate
duplicate same error message, and some caller is forgetting to do it.
And caller can't indicate detail function() error information.
If function() indicates error message, we can get same and
detail information without forgot.
int function(...)
{
...
if (ret < 0)
dev_err(...)
return ret;
}
int caller(...)
{
...
ret = function(...);
...
}
This patch follow above style at soc_pcm_prepare().
By this patch, dpcm_fe/be_dai_prepare(...)
temporary lacks FE/BE error info, but it will reborn soon.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o8flutbn.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuninori Morimoto [Mon, 15 Mar 2021 00:57:42 +0000 (09:57 +0900)]
ASoC: soc-pcm: indicate error message at soc_pcm_hw_params()
Indicating error message when failed case is very useful for debuging.
In many case, its style is like below.
int function(...)
{
...
return ret;
}
int caller(...)
{
...
ret = function(...);
if (ret < 0)
dev_err(...)
...
}
This is not so bad, but in this style *each caller* needs to indicate
duplicate same error message, and some caller is forgetting to do it.
And caller can't indicate detail function() error information.
If function() indicates error message, we can get same and
detail information without forgot.
int function(...)
{
...
if (ret < 0)
dev_err(...)
return ret;
}
int caller(...)
{
...
ret = function(...);
...
}
This patch follow above style at soc_pcm_hw_params().
By this patch, dpcm_fe/be_dai_hw_params(...)
temporary lacks FE/BE error info, but it will reborn soon.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pn01utbt.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuninori Morimoto [Mon, 15 Mar 2021 00:57:37 +0000 (09:57 +0900)]
ASoC: soc-pcm: indicate error message at soc_pcm_open()
Indicating error message when failed case is very useful for debuging.
In many case, its style is like below.
int function(...)
{
...
return ret;
}
int caller(...)
{
...
ret = function(...);
if (ret < 0)
dev_err(...)
...
}
This is not so bad, but in this style *each caller* needs to indicate
duplicate same error message, and some caller is forgetting to do it.
And caller can't indicate detail function() error information.
If function() indicates error message, we can get same and
detail information without forgot.
int function(...)
{
...
if (ret < 0)
dev_err(...)
return ret;
}
int caller(...)
{
...
ret = function(...);
...
}
This patch follow above style at soc_pcm_open().
By this patch, dpcm_fe/be_dai_startup(...)
temporary lacks FE/BE error info, but it will reborn soon.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r1khutby.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Thu, 18 Mar 2021 17:52:22 +0000 (17:52 +0000)]
Merge series "ASoC: codecs: remove cppcheck warnings" from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
Lots of small fixes in various codec drivers that should have no
functional impact.
Pierre-Louis Bossart (23):
ASoC: ab8500-codec: remove useless structure
ASoC: ad1836: remove useless return
ASoC: adau1977: remove useless return
ASoC: cros_ec_codec: remove null pointer dereference warning
ASoC: cx2070x: remove useless assignment
ASoC: cx2070x: remove duplicate else branch
ASoC: da7219-aad: remove useless initialization
ASoC: hdac_hdmi: remove useless initializations
ASoC: hdac_hdmi: align function arguments
ASoC: hdmi-codec: remove useless initialization
ASoC: hdmi-codec: remove unused spk_mask member
ASoC: max98090: remove useless assignment
ASoC: mt6358: remove useless initializations
ASoC: mt6359: remove useless assignment
ASoC: nau8825: remove useless assignment
ASoC: pcm1681: remove useless assignment
ASoC: sigmadsp: align function prototype
ASoC: sti-sas: remove unused struct members
ASoC: tas2562: remove useless assignment
ASoC: tas2562: remove warning on return value
ASoC: tas2770: remove useless initialization
ASoC: tlv320dac33: clarify expression
ASoC: tscs454: remove useless test on PLL disable
sound/soc/codecs/ab8500-codec.c | 7 -------
sound/soc/codecs/ad1836.c | 2 --
sound/soc/codecs/adau1977.c | 2 --
sound/soc/codecs/cros_ec_codec.c | 2 +-
sound/soc/codecs/cx2072x.c | 11 ++++-------
sound/soc/codecs/da7219-aad.c | 2 +-
sound/soc/codecs/hdac_hdmi.c | 14 +++++++-------
sound/soc/codecs/hdac_hdmi.h | 2 +-
sound/soc/codecs/hdmi-codec.c | 3 +--
sound/soc/codecs/max98090.c | 2 +-
sound/soc/codecs/mt6358.c | 4 ++--
sound/soc/codecs/mt6359.c | 4 ++--
sound/soc/codecs/nau8825.c | 2 +-
sound/soc/codecs/pcm1681.c | 2 +-
sound/soc/codecs/sigmadsp.h | 2 +-
sound/soc/codecs/sti-sas.c | 3 ---
sound/soc/codecs/tas2562.c | 3 +--
sound/soc/codecs/tas2770.c | 2 +-
sound/soc/codecs/tlv320dac33.c | 2 +-
sound/soc/codecs/tscs454.c | 7 ++++++-
20 files changed, 32 insertions(+), 46 deletions(-)
--
2.25.1
Mark Brown [Thu, 18 Mar 2021 17:52:21 +0000 (17:52 +0000)]
Merge series "Fix reset controls and RPM of NVIDIA Tegra ASoC drivers" from Dmitry Osipenko <digetx@gmail.com>:
Hi,
This series adds missing hardware reset controls to I2S and AC97 drivers,
corrects runtime PM usage and drivers probe/remove order. Currently drivers
happen to work properly because reset is implicitly deasserted by tegra-clk
driver, but clk driver shouldn't touch the resets and we need to fix it
because this breaks other Tegra drivers. Previously we fixed the resets of
the AHUB and HDMI codec drivers, but turned out that we missed the I2C and
AC97 drivers.
Thanks to Paul Fertser for testing the pending clk patches and finding
that audio got broken on Tegra20 AC100 netbook because of the missing I2S
reset.
Changelog:
v5: - After taking another look at the drivers I noticed couple more
things that could be improved. These new patches correct runtime PM
and probe/remove order of the drivers:
ASoC: tegra20: spdif: Correct driver removal order
ASoC: tegra20: spdif: Remove handing of disabled runtime PM
ASoC: tegra20: i2s: Add system level suspend-resume callbacks
ASoC: tegra20: i2s: Correct driver removal order
ASoC: tegra20: i2s: Use devm_clk_get()
ASoC: tegra20: i2s: Remove handing of disabled runtime PM
ASoC: tegra30: i2s: Correct driver removal order
ASoC: tegra30: i2s: Use devm_clk_get()
ASoC: tegra30: i2s: Remove handing of disabled runtime PM
ASoC: tegra30: ahub: Reset global variable
ASoC: tegra30: ahub: Correct suspend-resume callbacks
ASoC: tegra30: ahub: Remove handing of disabled runtime PM
v4: - Added missing prototype for reset_control_bulk_put().
v3: - Fixed reset stubs for !CONFIG_RESET_CONTROLLER.
v2: - After some more testing I found that I2S control logic doesn't require
I2S clock to be enabled for resetting. Hence it's fine to have I2S to
be reset by parent AHUB driver, so I dropped "tegra30: i2s: Add reset
control" patch.
- While I was double-checking resets on Tegra30, I found that that
Tegra30 I2S driver has a broken runtime PM which doesn't restore
hardware state on resume and it's lost after AHUB RPM-resume.
Thus, added this new patch "tegra30: i2s: Restore hardware state
on runtime PM resume".
- Added new patches which switch AHUB driver to use reset-bulk API.
I took the RFC patch from Philipp Zabel, fixed it and added
devm_reset_control_bulk_optional_get_exclusive_released() that
will be useful for further Tegra GPU patches. This is a minor
improvement which makes code cleaner.
Dmitry Osipenko (16):
ASoC: tegra20: ac97: Add reset control
ASoC: tegra20: i2s: Add reset control
ASoC: tegra30: i2s: Restore hardware state on runtime PM resume
ASoC: tegra30: ahub: Switch to use reset-bulk API
ASoC: tegra20: spdif: Correct driver removal order
ASoC: tegra20: spdif: Remove handing of disabled runtime PM
ASoC: tegra20: i2s: Add system level suspend-resume callbacks
ASoC: tegra20: i2s: Correct driver removal order
ASoC: tegra20: i2s: Use devm_clk_get()
ASoC: tegra20: i2s: Remove handing of disabled runtime PM
ASoC: tegra30: i2s: Correct driver removal order
ASoC: tegra30: i2s: Use devm_clk_get()
ASoC: tegra30: i2s: Remove handing of disabled runtime PM
ASoC: tegra30: ahub: Reset global variable
ASoC: tegra30: ahub: Correct suspend-resume callbacks
ASoC: tegra30: ahub: Remove handing of disabled runtime PM
Philipp Zabel (1):
reset: Add reset_control_bulk API
drivers/reset/core.c | 215 ++++++++++++++++++++++
include/linux/reset.h | 315 ++++++++++++++++++++++++++++++++
sound/soc/tegra/tegra20_ac97.c | 21 +++
sound/soc/tegra/tegra20_ac97.h | 1 +
sound/soc/tegra/tegra20_i2s.c | 60 +++---
sound/soc/tegra/tegra20_i2s.h | 1 +
sound/soc/tegra/tegra20_spdif.c | 16 +-
sound/soc/tegra/tegra30_ahub.c | 168 ++++++-----------
sound/soc/tegra/tegra30_ahub.h | 5 +-
sound/soc/tegra/tegra30_i2s.c | 65 ++-----
10 files changed, 667 insertions(+), 200 deletions(-)
--
2.30.2
base-commit:
a38fd8748464831584a19438cbb3082b5a2dab15
Brent Lu [Wed, 17 Mar 2021 11:08:24 +0000 (19:08 +0800)]
ASoC: Intel: sof_rt5682: Add ALC1015Q-VB speaker amp support
This patch adds jsl_rt5682_rt1015p which supports the RT5682 headset
codec and ALC1015Q-VB speaker amplifier combination on JasperLake
platform.
This driver also supports ALC1015Q-CG if running in auto-mode.
Following table shows the audio interface support of the two
amplifiers.
| ALC1015Q-CG | ALC1015Q-VB
=====================================
I2C | Yes | No
Auto-mode | 48K, 64fs | 16k, 32fs
| 48k, 32fs
| 48k, 64fs
Signed-off-by: Brent Lu <brent.lu@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210317110824.20814-1-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Jack Yu [Thu, 11 Mar 2021 02:58:09 +0000 (10:58 +0800)]
ASoC: rt1019: add rt1019 amplifier driver
This is initial amplifier driver for rt1019.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Link: https://lore.kernel.org/r/20210311025809.31852-1-jack.yu@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Bhaskar Chowdhury [Sat, 13 Mar 2021 23:18:50 +0000 (04:48 +0530)]
ASoC: Fix a typo in the file rt5682.txt
s/drving/driving/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210313231850.17278-1-unixbhaskar@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Nick Desaulniers [Mon, 15 Mar 2021 01:39:08 +0000 (18:39 -0700)]
ASoC: Intel: Skylake: skl-topology: fix -frame-larger-than
sound/soc/intel/skylake/skl-topology.c:3613:13: warning: stack frame
size of 1304 bytes in function 'skl_tplg_complete'
[-Wframe-larger-than=]
struct snd_ctl_elem_value is 1224 bytes in my configuration.
Heap allocate it, then free it within the current frame.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Nick Desaulniers <nick.desaulniers@gmail.com>
Link: https://lore.kernel.org/r/20210315013908.217219-1-nick.desaulniers@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:46 +0000 (12:22 -0600)]
ASoC: tscs454: remove useless test on PLL disable
cppcheck warning:
sound/soc/codecs/tscs454.c:730:37: style: Same value in both branches
of ternary operator. [duplicateValueTernary]
val = pll1 ? FV_PLL1CLKEN_DISABLE : FV_PLL2CLKEN_DISABLE;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-24-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:45 +0000 (12:22 -0600)]
ASoC: tlv320dac33: clarify expression
cppcheck warning:
sound/soc/codecs/tlv320dac33.c:1074:43: style: Clarify calculation
precedence for '%' and '?'. [clarifyCalculation]
(dac33->alarm_threshold % period_size ?
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-23-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:44 +0000 (12:22 -0600)]
ASoC: tas2770: remove useless initialization
cppcheck warning:
sound/soc/codecs/tas2770.c:109:10: style: Variable 'ret' is assigned a
value that is never used. [unreadVariable]
int ret = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-22-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:43 +0000 (12:22 -0600)]
ASoC: tas2562: remove warning on return value
cppcheck warning:
sound/soc/codecs/tas2562.c:530:9: warning: Identical condition and return expression 'ret', return value is always 0 [identicalConditionAfterEarlyExit]
return ret;
^
sound/soc/codecs/tas2562.c:525:6: note: If condition 'ret' is true, the function will return/exit
if (ret)
^
sound/soc/codecs/tas2562.c:530:9: note: Returning identical expression 'ret'
return ret;
^
Fix with return 0
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-21-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:42 +0000 (12:22 -0600)]
ASoC: tas2562: remove useless assignment
cppcheck throws a warning:
sound/soc/codecs/tas2562.c:203:4: style: Assignment of function
parameter has no effect outside the function. [uselessAssignmentArg]
tx_mask &= ~(1 << right_slot);
^
This assignment seems to come from a copy/paste but the value is
indeed not used. Let's remove it.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-20-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:41 +0000 (12:22 -0600)]
ASoC: sti-sas: remove unused struct members
cppcheck warnings:
sound/soc/codecs/sti-sas.c:54:25: style: struct member
'sti_dac_audio::field' is never used. [unusedStructMember]
struct regmap_field **field;
^
sound/soc/codecs/sti-sas.c:55:24: style: struct member
'sti_dac_audio::rst' is never used. [unusedStructMember]
struct reset_control *rst;
^
sound/soc/codecs/sti-sas.c:61:25: style: struct member
'sti_spdif_audio::field' is never used. [unusedStructMember]
struct regmap_field **field;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-19-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:40 +0000 (12:22 -0600)]
ASoC: sigmadsp: align function prototype
cppcheck warning:
sound/soc/codecs/sigmadsp.c:736:60: style:inconclusive: Function
'sigmadsp_setup' argument 2 names different: declaration 'rate'
definition 'samplerate'. [funcArgNamesDifferent]
int sigmadsp_setup(struct sigmadsp *sigmadsp, unsigned int samplerate)
^
sound/soc/codecs/sigmadsp.h:62:60: note: Function 'sigmadsp_setup'
argument 2 names different: declaration 'rate' definition
'samplerate'.
int sigmadsp_setup(struct sigmadsp *sigmadsp, unsigned int rate);
^
sound/soc/codecs/sigmadsp.c:736:60: note: Function 'sigmadsp_setup'
argument 2 names different: declaration 'rate' definition
'samplerate'.
int sigmadsp_setup(struct sigmadsp *sigmadsp, unsigned int samplerate)
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-18-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:39 +0000 (12:22 -0600)]
ASoC: pcm1681: remove useless assignment
cppcheck warning:
sound/soc/codecs/pcm1681.c:87:8: style: Variable 'i' is assigned a
value that is never used. [unreadVariable]
int i = 0, val = -1, enable = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-17-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:38 +0000 (12:22 -0600)]
ASoC: nau8825: remove useless assignment
cppcheck warning:
sound/soc/codecs/nau8825.c:2113:10: style: Variable 'ret' is assigned
a value that is never used. [unreadVariable]
int ret = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-16-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:37 +0000 (12:22 -0600)]
ASoC: mt6359: remove useless assignment
cppcheck warning:
sound/soc/codecs/mt6359.c:242:19: style: Variable 'stage' is assigned a value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
sound/soc/codecs/mt6359.c:260:19: style: Variable 'stage' is assigned a value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
sound/soc/codecs/mt6359.c:274:8: style: Variable 'i' is assigned a value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
sound/soc/codecs/mt6359.c:274:19: style: Variable 'stage' is assigned a value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-15-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:36 +0000 (12:22 -0600)]
ASoC: mt6358: remove useless initializations
cppcheck warnings:
sound/soc/codecs/mt6358.c:334:19: style: Variable 'stage' is assigned
a value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
sound/soc/codecs/mt6358.c:350:19: style: Variable 'stage' is assigned
a value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
185/930 files checked 25% done
Checking sound/soc/codecs/mt6359.c ...
sound/soc/codecs/mt6359.c:274:8: style: Variable 'i' is assigned a
value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
sound/soc/codecs/mt6359.c:274:19: style: Variable 'stage' is assigned
a value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-14-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:35 +0000 (12:22 -0600)]
ASoC: max98090: remove useless assignment
cppcheck warning:
sound/soc/codecs/max98090.c:1835:16: style: Variable 'test_diff' is
assigned a value that is never used. [unreadVariable]
int test_diff = INT_MAX;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-13-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:34 +0000 (12:22 -0600)]
ASoC: hdmi-codec: remove unused spk_mask member
fix cppcheck warning:
sound/soc/codecs/hdmi-codec.c:25:16: style: struct member
'hdmi_codec_channel_map_table::spk_mask' is never
used. [unusedStructMember]
unsigned long spk_mask; /* speaker position bit mask */
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-12-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:33 +0000 (12:22 -0600)]
ASoC: hdmi-codec: remove useless initialization
Fix cppcheck warning:
sound/soc/codecs/hdmi-codec.c:745:5: style: Redundant initialization
for 'cf'. The initialized value is overwritten before it is
read. [redundantInitialization]
cf = dai->playback_dma_data;
^
sound/soc/codecs/hdmi-codec.c:738:31: note: cf is initialized
struct hdmi_codec_daifmt *cf = dai->playback_dma_data;
^
sound/soc/codecs/hdmi-codec.c:745:5: note: cf is overwritten
cf = dai->playback_dma_data;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:32 +0000 (12:22 -0600)]
ASoC: hdac_hdmi: align function arguments
cppcheck warning:
sound/soc/codecs/hdac_hdmi.c:1882:54: style:inconclusive: Function
'hdac_hdmi_jack_init' argument 2 names different: declaration 'pcm'
definition 'device'. [funcArgNamesDifferent]
int hdac_hdmi_jack_init(struct snd_soc_dai *dai, int device,
^
sound/soc/codecs/hdac_hdmi.h:5:54: note: Function
'hdac_hdmi_jack_init' argument 2 names different: declaration 'pcm'
definition 'device'.
int hdac_hdmi_jack_init(struct snd_soc_dai *dai, int pcm,
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:31 +0000 (12:22 -0600)]
ASoC: hdac_hdmi: remove useless initializations
Cppcheck complains a lot about possible null pointer dereferences but
it's again a case of useless initializations to NULL.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:30 +0000 (12:22 -0600)]
ASoC: da7219-aad: remove useless initialization
cppcheck warning:
sound/soc/codecs/da7219-aad.c:118:22: style: Variable 'ret' is
assigned a value that is never used. [unreadVariable]
int report = 0, ret = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20210312182246.5153-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:29 +0000 (12:22 -0600)]
ASoC: cx2070x: remove duplicate else branch
cppcheck warning:
sound/soc/codecs/cx2072x.c:1436:10: style:inconclusive: Found
duplicate branches for 'if' and 'else'. [duplicateBranch]
} else if (type & 0x4) {
^
sound/soc/codecs/cx2072x.c:1439:5: note: Found duplicate branches for
'if' and 'else'.
} else {
^
sound/soc/codecs/cx2072x.c:1436:10: note: Found duplicate branches for
'if' and 'else'.
} else if (type & 0x4) {
^
The last two branches do the same thing and can be collapsed together.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210312182246.5153-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:28 +0000 (12:22 -0600)]
ASoC: cx2070x: remove useless assignment
Cppcheck warning:
sound/soc/codecs/cx2072x.c:830:26: style: Variable
'reg1.r.rx_data_one_line' is reassigned a value before the old one has
been used. [redundantAssignment]
reg1.r.rx_data_one_line = 1;
^
sound/soc/codecs/cx2072x.c:782:26: note: reg1.r.rx_data_one_line is
assigned
reg1.r.rx_data_one_line = 1;
^
sound/soc/codecs/cx2072x.c:830:26: note: reg1.r.rx_data_one_line is
overwritten
reg1.r.rx_data_one_line = 1;
^
sound/soc/codecs/cx2072x.c:831:26: style: Variable
'reg1.r.tx_data_one_line' is reassigned a value before the old one has
been used. [redundantAssignment]
reg1.r.tx_data_one_line = 1;
^
sound/soc/codecs/cx2072x.c:783:26: note: reg1.r.tx_data_one_line is
assigned
reg1.r.tx_data_one_line = 1;
^
sound/soc/codecs/cx2072x.c:831:26: note: reg1.r.tx_data_one_line is
overwritten
reg1.r.tx_data_one_line = 1;
^
Likely copy/paste.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210312182246.5153-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:27 +0000 (12:22 -0600)]
ASoC: cros_ec_codec: remove null pointer dereference warning
Cppcheck complains of a possible issue:
sound/soc/codecs/cros_ec_codec.c:98:10: warning: Possible null pointer
dereference: in [nullPointer]
memcpy(in, msg->data, insize);
^
sound/soc/codecs/cros_ec_codec.c:162:34: note: Calling function
'send_ec_host_command', 5th argument 'NULL' value is 0
(uint8_t *)&p, sizeof(p), NULL, 0);
^
sound/soc/codecs/cros_ec_codec.c:98:10: note: Null pointer dereference
memcpy(in, msg->data, insize);
^
In practice the access to the pointer is protected by another
argument, but this is likely to fool other static analysis tools. Add
a test to avoid doing the memcpy if the pointer is NULL or the size is
zero.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210312182246.5153-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:26 +0000 (12:22 -0600)]
ASoC: adau1977: remove useless return
Cppcheck warning:
sound/soc/codecs/adau1977.c:242:9: warning: Identical condition and
return expression 'ret', return value is always 0
[identicalConditionAfterEarlyExit]
return ret;
^
sound/soc/codecs/adau1977.c:239:6: note: If condition 'ret' is true,
the function will return/exit
if (ret)
^
sound/soc/codecs/adau1977.c:242:9: note: Returning identical expression 'ret'
return ret;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:25 +0000 (12:22 -0600)]
ASoC: ad1836: remove useless return
Cppcheck warning:
sound/soc/codecs/ad1836.c:311:9: warning: Identical condition and return expression 'ret', return value is always 0 [identicalConditionAfterEarlyExit]
return ret;
^
sound/soc/codecs/ad1836.c:308:6: note: If condition 'ret' is true, the function will return/exit
if (ret)
^
sound/soc/codecs/ad1836.c:311:9: note: Returning identical expression 'ret'
return ret;
^
Likely copy/paste between adc and dac cases.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Fri, 12 Mar 2021 18:22:24 +0000 (12:22 -0600)]
ASoC: ab8500-codec: remove useless structure
Cppcheck warnings:
sound/soc/codecs/ab8500-codec.c:117:20: style: struct member 'ab8500_codec_drvdata_dbg::vaud' is never used. [unusedStructMember]
struct regulator *vaud;
^
sound/soc/codecs/ab8500-codec.c:118:20: style: struct member 'ab8500_codec_drvdata_dbg::vamic1' is never used. [unusedStructMember]
struct regulator *vamic1;
^
sound/soc/codecs/ab8500-codec.c:119:20: style: struct member 'ab8500_codec_drvdata_dbg::vamic2' is never used. [unusedStructMember]
struct regulator *vamic2;
^
sound/soc/codecs/ab8500-codec.c:120:20: style: struct member 'ab8500_codec_drvdata_dbg::vdmic' is never used. [unusedStructMember]
struct regulator *vdmic;
^
The structure is never used, remove.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko [Sun, 14 Mar 2021 15:44:59 +0000 (18:44 +0300)]
ASoC: tegra30: ahub: Remove handing of disabled runtime PM
Runtime PM is always available on Tegra since commit
40b2bb1b132a
("ARM: tegra: enforce PM requirement"), hence there is no need to
handle the case of a disabled RPM by Tegra drivers. Remove handing
of a disabled runtime PM from Tegra30 AHUB driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-18-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko [Sun, 14 Mar 2021 15:44:58 +0000 (18:44 +0300)]
ASoC: tegra30: ahub: Correct suspend-resume callbacks
Tegra30 AHUB driver always syncs hardware state on a runtime PM resume,
hence there is no needed to re-sync the state on system resume. Replace
the suspend-resume callbacks with a generic helpers which ensure that
AHUB is suspended using RPM callbacks across system suspend-resume.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-17-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko [Sun, 14 Mar 2021 15:44:57 +0000 (18:44 +0300)]
ASoC: tegra30: ahub: Reset global variable
Tegra30 AHUB uses global variable that is never reset by the driver on
a probe failure and on driver removal, meaning that driver will never try
to re-probe and can't be unbound. Make driver to reset the variable.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-16-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko [Sun, 14 Mar 2021 15:44:56 +0000 (18:44 +0300)]
ASoC: tegra30: i2s: Remove handing of disabled runtime PM
Runtime PM is always available on Tegra since commit
40b2bb1b132a
("ARM: tegra: enforce PM requirement"), hence there is no need to
handle the case of a disabled RPM by Tegra drivers. Remove handing
of a disabled runtime PM from Tegra30 I2S driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-15-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko [Sun, 14 Mar 2021 15:44:55 +0000 (18:44 +0300)]
ASoC: tegra30: i2s: Use devm_clk_get()
Use resource-managed variant of clk_get() to simplify code.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-14-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko [Sun, 14 Mar 2021 15:44:54 +0000 (18:44 +0300)]
ASoC: tegra30: i2s: Correct driver removal order
Tegra30 I2S driver has a wrong driver removal order, which should be
opposite to the registration order, but it's not. In particular the
runtime PM is disabled in a wrong order. Fix the order.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-13-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko [Sun, 14 Mar 2021 15:44:53 +0000 (18:44 +0300)]
ASoC: tegra20: i2s: Remove handing of disabled runtime PM
Runtime PM is always available on Tegra since commit
40b2bb1b132a
("ARM: tegra: enforce PM requirement"), hence there is no need to
handle the case of a disabled RPM by Tegra drivers. Remove handing
of a disabled runtime PM from Tegra20 I2S driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-12-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko [Sun, 14 Mar 2021 15:44:52 +0000 (18:44 +0300)]
ASoC: tegra20: i2s: Use devm_clk_get()
Use resource-managed variant of clk_get() to simplify code.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-11-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko [Sun, 14 Mar 2021 15:44:51 +0000 (18:44 +0300)]
ASoC: tegra20: i2s: Correct driver removal order
Tegra20 I2S driver has a wrong driver removal order, which should be
opposite to the registration order, but it's not. In particular the
runtime PM is disabled in a wrong order. Fix the order.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-10-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko [Sun, 14 Mar 2021 15:44:50 +0000 (18:44 +0300)]
ASoC: tegra20: i2s: Add system level suspend-resume callbacks
Add system level suspend-resume callbacks in order to ensure that I2S
is gated before system is suspended. This puts Tegra20 I2S driver on
par with the Tegra30 I2S driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-9-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko [Sun, 14 Mar 2021 15:44:49 +0000 (18:44 +0300)]
ASoC: tegra20: spdif: Remove handing of disabled runtime PM
Runtime PM is always available on Tegra since commit
40b2bb1b132a
("ARM: tegra: enforce PM requirement"), hence there is no need to
handle the case of a disabled RPM by Tegra drivers. Remove handing
of a disabled runtime PM from Tegra20 SPDIF driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-8-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko [Sun, 14 Mar 2021 15:44:48 +0000 (18:44 +0300)]
ASoC: tegra20: spdif: Correct driver removal order
Tegra20 SPDIF driver has a wrong driver removal order, which should be
opposite to the registration order, but it's not. In particular the
runtime PM is disabled in a wrong order. Fix the order.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-7-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko [Sun, 14 Mar 2021 15:44:47 +0000 (18:44 +0300)]
ASoC: tegra30: ahub: Switch to use reset-bulk API
Switch to use reset-bulk API in order to make code cleaner.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-6-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Philipp Zabel [Sun, 14 Mar 2021 15:44:46 +0000 (18:44 +0300)]
reset: Add reset_control_bulk API
Follow the clock and regulator subsystems' lead and add a bulk API
for reset controls.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-5-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko [Sun, 14 Mar 2021 15:44:45 +0000 (18:44 +0300)]
ASoC: tegra30: i2s: Restore hardware state on runtime PM resume
Tegra30 I2S driver syncs regmap cache only on resume from system suspend,
but hardware is reset across the runtime suspend because RPM of the parent
AHUB driver resets the I2S hardware, hence h/w state is lost after each
RPM resume. The problem isn't visible because hardware happens to be fully
reprogrammed after each RPM resume. Move hardware syncing to RPM resume in
order to restore h/w state properly.
Fixes:
ed9ce1ed2239 ("ASoC: tegra: ahub: Reset hardware properly")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-4-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko [Sun, 14 Mar 2021 15:44:44 +0000 (18:44 +0300)]
ASoC: tegra20: i2s: Add reset control
The I2S reset may be asserted at a boot time, in particular this is the
case on Tegra20 AC100 netbook. Tegra20 I2S driver doesn't manage the
reset control and currently it happens to work because reset is implicitly
deasserted by the tegra-clk driver when I2S clock is enabled. The I2S
permanently stays in a reset once tegra-clk is fixed to not touch the
resets, which it shouldn't be doing. Add reset control to the Tegra20
I2S driver.
Note that I2S reset was always specified in Tegra20 device-tree, hence
DTB ABI changes aren't required.
Tested-by: Paul Fertser <fercerpav@gmail.com> # T20 AC100
Reported-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-3-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko [Sun, 14 Mar 2021 15:44:43 +0000 (18:44 +0300)]
ASoC: tegra20: ac97: Add reset control
Tegra20 AC97 driver doesn't manage the AC97 controller reset, relying on
implicit deassertion of the reset by tegra-clk driver, which needs to be
fixed since this behaviour is unacceptable by other Tegra drivers. Add
explicit reset control to the Tegra20 AC97 driver.
Note that AC97 reset was always specified in Tegra20 device-tree, hence
DTB ABI changes aren't required.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-2-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hans de Goede [Sun, 7 Mar 2021 15:18:00 +0000 (16:18 +0100)]
ASoC/extcon: arizona: Move arizona jack code to sound/soc/codecs/arizona-jack.c
The jack handling for arizona codecs is being refactored so that it is
done directly by the codec drivers, instead of having an extcon-driver
bind to a separate "arizona-extcon" child-device for this.
drivers/mfd/arizona-core.c has already been updated to no longer
instantiate an "arizona-extcon" child-device for the arizona codecs.
This means that the "arizona-extcon" driver is no longer useful
(there are no longer any devices for it to bind to).
This commit drops the extcon Kconfig / Makefile bits and moves
drivers/extcon/extcon-arizona.c to sound/soc/codecs/arizona-jack.c .
This is a preparation patch for converting the arizona extcon-driver into
a helper library for letting the arizona codec-drivers directly report jack
state through the standard sound/soc/soc-jack.c functions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Hans de Goede [Sun, 7 Mar 2021 15:17:59 +0000 (16:17 +0100)]
extcon: arizona: Always use pm_runtime_get_sync() when we need the device to be awake
Before this commit the extcon-arizona code was mixing pm_runtime_get()
and pm_runtime_get_sync() in different places.
In all places where pm_runtime_get[_sync]() is called, the code
makes use of the device immediately after the call.
This means that we should always use pm_runtime_get_sync().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Hans de Goede [Sun, 7 Mar 2021 15:17:58 +0000 (16:17 +0100)]
extcon: arizona: Fix flags parameter to the gpiod_get("wlf,micd-pol") call
The initial value of the GPIO should match the info->micd_modes[0].gpio
value. arizona_extcon_probe() already stores the necessary flag in a
mode variable, but instead of passing mode as flags to the gpiod_get()
it was using a hardcoded GPIOD_OUT_LOW.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Hans de Goede [Sun, 7 Mar 2021 15:17:57 +0000 (16:17 +0100)]
extcon: arizona: Fix various races on driver unbind
We must free/disable all interrupts and cancel all pending works
before doing further cleanup.
Before this commit arizona_extcon_remove() was doing several
register writes to shut things down before disabling the IRQs
and it was cancelling only 1 of the 3 different works used.
Move all the register-writes shutting things down to after
the disabling of the IRQs and add the 2 missing
cancel_delayed_work_sync() calls.
This fixes various possible races on driver unbind. One of which
would always trigger on devices using the mic-clamp feature for
jack detection. The ARIZONA_MICD_CLAMP_MODE_MASK update was
done before disabling the IRQs, causing:
1. arizona_jackdet() to run
2. detect a jack being inserted (clamp disabled means jack inserted)
3. call arizona_start_mic() which:
3.1 Enables the MICVDD regulator
3.2 takes a pm_runtime_reference
And this was all happening after the ARIZONA_MICD_ENA bit clearing,
which would undo 3.1 and 3.2 because the ARIZONA_MICD_CLAMP_MODE_MASK
update was being done after the ARIZONA_MICD_ENA bit clearing.
So this means that arizona_extcon_remove() would exit with
1. MICVDD enabled and 2. The pm_runtime_reference being unbalanced.
MICVDD still being enabled caused the following oops when the
regulator is released by the devm framework:
[ 2850.745757] ------------[ cut here ]------------
[ 2850.745827] WARNING: CPU: 2 PID: 2098 at drivers/regulator/core.c:2123 _regulator_put.part.0+0x19f/0x1b0
[ 2850.745835] Modules linked in: extcon_arizona ...
...
[ 2850.746909] Call Trace:
[ 2850.746932] regulator_put+0x2d/0x40
[ 2850.746946] release_nodes+0x22a/0x260
[ 2850.746984] __device_release_driver+0x190/0x240
[ 2850.747002] driver_detach+0xd4/0x120
...
[ 2850.747337] ---[ end trace
f455dfd7abd9781f ]---
Note this oops is just one of various theoretically possible races caused
by the wrong ordering inside arizona_extcon_remove(), this fixes the
ordering fixing all possible races, including the reported oops.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Hans de Goede [Sun, 7 Mar 2021 15:17:56 +0000 (16:17 +0100)]
extcon: arizona: Fix some issues when HPDET IRQ fires after the jack has been unplugged
When the jack is partially inserted and then removed again it may be
removed while the hpdet code is running. In this case the following
may happen:
1. The "JACKDET rise" or ""JACKDET fall" IRQ triggers
2. arizona_jackdet runs and takes info->lock
3. The "HPDET" IRQ triggers
4. arizona_hpdet_irq runs, blocks on info->lock
5. arizona_jackdet calls arizona_stop_mic() and clears info->hpdet_done
6. arizona_jackdet releases info->lock
7. arizona_hpdet_irq now can continue running and:
7.1 Calls arizona_start_mic() (if a mic was detected)
7.2 sets info->hpdet_done
Step 7 is undesirable / a bug:
7.1 causes the device to stay in a high power-state (with MICVDD enabled)
7.2 causes hpdet to not run on the next jack insertion, which in turn
causes the EXTCON_JACK_HEADPHONE state to never get set
This fixes both issues by skipping these 2 steps when arizona_hpdet_irq
runs after the jack has been unplugged.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Hans de Goede [Sun, 7 Mar 2021 15:17:55 +0000 (16:17 +0100)]
mfd: arizona: Drop arizona-extcon cells
The arizona jack-dection handling is being reworked so that the
codec-child-device drivers directly handle jack-detect themselves,
so it is no longer necessary to instantiate "arizona-extcon"
child-devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bhaskar Chowdhury [Wed, 17 Mar 2021 08:20:42 +0000 (13:50 +0530)]
ASoC: ti: Fix a typo in the file ams-delta.c
s/functonality/functionality/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Link: https://lore.kernel.org/r/20210317082042.3670745-1-unixbhaskar@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Tue, 16 Mar 2021 17:55:39 +0000 (17:55 +0000)]
Merge series "ASoC: SOF: debug: cleanups" from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
cleanups of allocation and error handling
Guennadi Liakhovetski (3):
ASoC: SOF: fix debugfs initialisation error handling
ASoC: SOF: only allocate debugfs cache buffers for IPC flood entries
ASoC: SOF: remove superfluous NULL check in debugfs read
sound/soc/sof/core.c | 5 +++--
sound/soc/sof/debug.c | 21 +++++++++++----------
2 files changed, 14 insertions(+), 12 deletions(-)
--
2.25.1
Yang Li [Thu, 4 Mar 2021 09:08:01 +0000 (17:08 +0800)]
ASoC: imx-hdmi: fix platform_no_drv_owner.cocci warnings
./sound/soc/fsl/imx-hdmi.c:226:3-8: No need to set .owner here. The core
will do it.
Remove .owner field if calls are used which set it automatically
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1614848881-29637-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mikhail Durnev [Tue, 16 Mar 2021 04:47:35 +0000 (14:47 +1000)]
ASoC: rsnd: core: Check convert rate in rsnd_hw_params
snd_pcm_hw_params_set_rate_near can return incorrect sample rate in
some cases, e.g. when the backend output rate is set to some value higher
than 48000 Hz and the input rate is 8000 Hz. So passing the value returned
by snd_pcm_hw_params_set_rate_near to snd_pcm_hw_params will result in
"FSO/FSI ratio error" and playing no audio at all while the userland
is not properly notified about the issue.
If SRC is unable to convert the requested sample rate to the sample rate
the backend is using, then the requested sample rate should be adjusted in
rsnd_hw_params. The userland will be notified about that change in the
returned hw_params structure.
Signed-off-by: Mikhail Durnev <mikhail_durnev@mentor.com>
Link: https://lore.kernel.org/r/1615870055-13954-1-git-send-email-mikhail_durnev@mentor.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fabio Estevam [Mon, 15 Mar 2021 19:38:42 +0000 (16:38 -0300)]
ASoC: mx27vis: Remove unused file
i.MX has been converted to a devicetree-only platform and
asoc-mx27vis.h is no longer used.
Get rid of this unused file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210315193842.183042-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Viorel Suman [Tue, 16 Mar 2021 09:42:16 +0000 (17:42 +0800)]
ASoC: fsl_spdif: use snd_ctl_boolean_mono_info
Remove redundant code and use snd_ctl_boolean_mono_info
instead.
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1615887736-31217-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>