OSDN Git Service
Doug Berger [Tue, 5 Nov 2019 19:07:24 +0000 (11:07 -0800)]
net: bcmgenet: use RGMII loopback for MAC reset
As noted in commit
28c2d1a7a0bf ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked while sw_reset
is asserted for its state machines to reset cleanly.
The transmit and receive clocks used by the UniMAC are derived from
the signals used on its PHY interface. The bcmgenet MAC can be
configured to work with different PHY interfaces including MII,
GMII, RGMII, and Reverse MII on internal and external interfaces.
Unfortunately for the UniMAC, when configured for MII the Tx clock
is always driven from the PHY which places it outside of the direct
control of the MAC.
The earlier commit enabled a local loopback mode within the UniMAC
so that the receive clock would be derived from the transmit clock
which addressed the observed issue with an external GPHY disabling
it's Rx clock. However, when a Tx clock is not available this
loopback is insufficient.
This commit implements a workaround that leverages the fact that
the MAC can reliably generate all of its necessary clocking by
enterring the external GPHY RGMII interface mode with the UniMAC in
local loopback during the sw_reset interval. Unfortunately, this
has the undesirable side efect of the RGMII GTXCLK signal being
driven during the same window.
In most configurations this is a benign side effect as the signal
is either not routed to a pin or is already expected to drive the
pin. The one exception is when an external MII PHY is expected to
drive the same pin with its TX_CLK output creating output driver
contention.
This commit exploits the IEEE 802.3 clause 22 standard defined
isolate mode to force an external MII PHY to present a high
impedance on its TX_CLK output during the window to prevent any
contention at the pin.
The MII interface is used internally with the 40nm internal EPHY
which agressively disables its clocks for power savings leading to
incomplete resets of the UniMAC and many instabilities observed
over the years. The workaround of this commit is expected to put
an end to those problems.
Fixes:
1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Tue, 5 Nov 2019 12:13:48 +0000 (14:13 +0200)]
Documentation: TLS: Add missing counter description
Add TLS TX counter description for the handshake retransmitted
packets that triggers the resync procedure then skip it, going
into the regular transmit flow.
Fixes:
46a3ea98074e ("net/mlx5e: kTLS, Enhance TX resync flow")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pan Bian [Tue, 5 Nov 2019 08:34:07 +0000 (16:34 +0800)]
NFC: fdp: fix incorrect free object
The address of fw_vsc_cfg is on stack. Releasing it with devm_kfree() is
incorrect, which may result in a system crash or other security impacts.
The expected object to free is *fw_vsc_cfg.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 5 Nov 2019 05:38:43 +0000 (21:38 -0800)]
net: prevent load/store tearing on sk->sk_stamp
Add a couple of READ_ONCE() and WRITE_ONCE() to prevent
load-tearing and store-tearing in sock_read_timestamp()
and sock_write_timestamp()
This might prevent another KCSAN report.
Fixes:
3a0ed3e96197 ("sock: Make sock->sk_stamp thread-safe")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Tranchetti [Tue, 5 Nov 2019 00:54:22 +0000 (17:54 -0700)]
net: qualcomm: rmnet: Fix potential UAF when unregistering
During the exit/unregistration process of the RmNet driver, the function
rmnet_unregister_real_device() is called to handle freeing the driver's
internal state and removing the RX handler on the underlying physical
device. However, the order of operations this function performs is wrong
and can lead to a use after free of the rmnet_port structure.
Before calling netdev_rx_handler_unregister(), this port structure is
freed with kfree(). If packets are received on any RmNet devices before
synchronize_net() completes, they will attempt to use this already-freed
port structure when processing the packet. As such, before cleaning up any
other internal state, the RX handler must be unregistered in order to
guarantee that no further packets will arrive on the device.
Fixes:
ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 4 Nov 2019 23:36:57 +0000 (15:36 -0800)]
net/tls: fix sk_msg trim on fallback to copy mode
sk_msg_trim() tries to only update curr pointer if it falls into
the trimmed region. The logic, however, does not take into the
account pointer wrapping that sk_msg_iter_var_prev() does nor
(as John points out) the fact that msg->sg is a ring buffer.
This means that when the message was trimmed completely, the new
curr pointer would have the value of MAX_MSG_FRAGS - 1, which is
neither smaller than any other value, nor would it actually be
correct.
Special case the trimming to 0 length a little bit and rework
the comparison between curr and end to take into account wrapping.
This bug caused the TLS code to not copy all of the message, if
zero copy filled in fewer sg entries than memcopy would need.
Big thanks to Alexander Potapenko for the non-KMSAN reproducer.
v2:
- take into account that msg->sg is a ring buffer (John).
Link: https://lore.kernel.org/netdev/20191030160542.30295-1-jakub.kicinski@netronome.com/
Fixes:
d829e9c4112b ("tls: convert to generic sk_msg interface")
Reported-by: syzbot+f8495bff23a879a6d0bd@syzkaller.appspotmail.com
Reported-by: syzbot+6f50c99e8f6194bf363f@syzkaller.appspotmail.com
Co-developed-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dotan Barak [Sun, 3 Nov 2019 09:11:35 +0000 (11:11 +0200)]
mlx4_core: fix wrong comment about the reason of subtract one from the max_cqes
The reason for the pre-allocation of one CQE is to enable resizing of
the CQ.
Fix comment accordingly.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.com>
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sun, 3 Nov 2019 03:17:39 +0000 (20:17 -0700)]
net: dsa: bcm_sf2: Fix driver removal
With the DSA core doing the call to dsa_port_disable() we do not need to
do that within the driver itself. This could cause an use after free
since past dsa_unregister_switch() we should not be accessing any
dsa_switch internal structures.
Fixes:
0394a63acfe2 ("net: dsa: enable and disable all ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Sat, 2 Nov 2019 14:17:47 +0000 (14:17 +0000)]
net: sched: prevent duplicate flower rules from tcf_proto destroy race
When a new filter is added to cls_api, the function
tcf_chain_tp_insert_unique() looks up the protocol/priority/chain to
determine if the tcf_proto is duplicated in the chain's hashtable. It then
creates a new entry or continues with an existing one. In cls_flower, this
allows the function fl_ht_insert_unque to determine if a filter is a
duplicate and reject appropriately, meaning that the duplicate will not be
passed to drivers via the offload hooks. However, when a tcf_proto is
destroyed it is removed from its chain before a hardware remove hook is
hit. This can lead to a race whereby the driver has not received the
remove message but duplicate flows can be accepted. This, in turn, can
lead to the offload driver receiving incorrect duplicate flows and out of
order add/delete messages.
Prevent duplicates by utilising an approach suggested by Vlad Buslov. A
hash table per block stores each unique chain/protocol/prio being
destroyed. This entry is only removed when the full destroy (and hardware
offload) has completed. If a new flow is being added with the same
identiers as a tc_proto being detroyed, then the add request is replayed
until the destroy is complete.
Fixes:
8b64678e0af8 ("net: sched: refactor tp insert/delete for concurrent execution")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reported-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nishad Kamdar [Sat, 2 Nov 2019 11:44:42 +0000 (17:14 +0530)]
net: hns3: Use the correct style for SPDX License Identifier
This patch corrects the SPDX License Identifier style in
header files related to Hisilicon network devices. For C header files
Documentation/process/license-rules.rst mandates C-like comments
(opposed to C source files where C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jay Vosburgh [Sat, 2 Nov 2019 04:56:42 +0000 (21:56 -0700)]
bonding: fix state transition issue in link monitoring
Since
de77ecd4ef02 ("bonding: improve link-status update in
mii-monitoring"), the bonding driver has utilized two separate variables
to indicate the next link state a particular slave should transition to.
Each is used to communicate to a different portion of the link state
change commit logic; one to the bond_miimon_commit function itself, and
another to the state transition logic.
Unfortunately, the two variables can become unsynchronized,
resulting in incorrect link state transitions within bonding. This can
cause slaves to become stuck in an incorrect link state until a
subsequent carrier state transition.
The issue occurs when a special case in bond_slave_netdev_event
sets slave->link directly to BOND_LINK_FAIL. On the next pass through
bond_miimon_inspect after the slave goes carrier up, the BOND_LINK_FAIL
case will set the proposed next state (link_new_state) to BOND_LINK_UP,
but the new_link to BOND_LINK_DOWN. The setting of the final link state
from new_link comes after that from link_new_state, and so the slave
will end up incorrectly in _DOWN state.
Resolve this by combining the two variables into one.
Reported-by: Aleksei Zakharov <zakharov.a.g@yandex.ru>
Reported-by: Sha Zhang <zhangsha.zhang@huawei.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Fixes:
de77ecd4ef02 ("bonding: improve link-status update in mii-monitoring")
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 6 Nov 2019 01:38:21 +0000 (17:38 -0800)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2019-11-02
The following pull-request contains BPF updates for your *net* tree.
We've added 6 non-merge commits during the last 6 day(s) which contain
a total of 8 files changed, 35 insertions(+), 9 deletions(-).
The main changes are:
1) Fix ppc BPF JIT's tail call implementation by performing a second pass
to gather a stable JIT context before opcode emission, from Eric Dumazet.
2) Fix build of BPF samples sys_perf_event_open() usage to compiled out
unavailable test_attr__{enabled,open} checks. Also fix potential overflows
in bpf_map_{area_alloc,charge_init} on 32 bit archs, from Björn Töpel.
3) Fix narrow loads of bpf_sysctl context fields with offset > 0 on big endian
archs like s390x and also improve the test coverage, from Ilya Leoshkevich.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Fri, 1 Nov 2019 23:28:28 +0000 (01:28 +0200)]
taprio: fix panic while hw offload sched list swap
Don't swap oper and admin schedules too early, it's not correct and
causes crash.
Steps to reproduce:
1)
tc qdisc replace dev eth0 parent root handle 100 taprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 1@2 \
base-time $SOME_BASE_TIME \
sched-entry S 01 80000 \
sched-entry S 02 15000 \
sched-entry S 04 40000 \
flags 2
2)
tc qdisc replace dev eth0 parent root handle 100 taprio \
base-time $SOME_BASE_TIME \
sched-entry S 01 90000 \
sched-entry S 02 20000 \
sched-entry S 04 40000 \
flags 2
3)
tc qdisc replace dev eth0 parent root handle 100 taprio \
base-time $SOME_BASE_TIME \
sched-entry S 01 150000 \
sched-entry S 02 200000 \
sched-entry S 04 40000 \
flags 2
Do 2 3 2 .. steps more times if not happens and observe:
[ 305.832319] Unable to handle kernel write to read-only memory at
virtual address
ffff0000087ce7f0
[ 305.910887] CPU: 0 PID: 0 Comm: swapper/0 Not tainted
[ 305.919306] Hardware name: Texas Instruments AM654 Base Board (DT)
[...]
[ 306.017119] x1 :
ffff800848031d88 x0 :
ffff800848031d80
[ 306.022422] Call trace:
[ 306.024866] taprio_free_sched_cb+0x4c/0x98
[ 306.029040] rcu_process_callbacks+0x25c/0x410
[ 306.033476] __do_softirq+0x10c/0x208
[ 306.037132] irq_exit+0xb8/0xc8
[ 306.040267] __handle_domain_irq+0x64/0xb8
[ 306.044352] gic_handle_irq+0x7c/0x178
[ 306.048092] el1_irq+0xb0/0x128
[ 306.051227] arch_cpu_idle+0x10/0x18
[ 306.054795] do_idle+0x120/0x138
[ 306.058015] cpu_startup_entry+0x20/0x28
[ 306.061931] rest_init+0xcc/0xd8
[ 306.065154] start_kernel+0x3bc/0x3e4
[ 306.068810] Code:
f2fbd5b7 f2fbd5b6 d503201f f9400422 (
f9000662)
[ 306.074900] ---[ end trace
96c8e2284a9d9d6e ]---
[ 306.079507] Kernel panic - not syncing: Fatal exception in interrupt
[ 306.085847] SMP: stopping secondary CPUs
[ 306.089765] Kernel Offset: disabled
Try to explain one of the possible crash cases:
The "real" admin list is assigned when admin_sched is set to
new_admin, it happens after "swap", that assigns to oper_sched NULL.
Thus if call qdisc show it can crash.
Farther, next second time, when sched list is updated, the admin_sched
is not NULL and becomes the oper_sched, previous oper_sched was NULL so
just skipped. But then admin_sched is assigned new_admin, but schedules
to free previous assigned admin_sched (that already became oper_sched).
Farther, next third time, when sched list is updated,
while one more swap, oper_sched is not null, but it was happy to be
freed already (while prev. admin update), so while try to free
oper_sched the kernel panic happens at taprio_free_sched_cb().
So, move the "swap emulation" where it should be according to function
comment from code.
Fixes:
9c66d15646760e ("taprio: Add support for hardware offloading")
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 Nov 2019 21:29:18 +0000 (13:29 -0800)]
Merge tag 'linux-can-fixes-for-5.4-
20191105' of git://git./linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2019-11-05
this is a pull request of 33 patches for net/master.
In the first patch Wen Yang's patch adds a missing of_node_put() to CAN device
infrastructure.
Navid Emamdoost's patch for the gs_usb driver fixes a memory leak in the
gs_can_open() error path.
Johan Hovold provides two patches, one for the mcba_usb, the other for the
usb_8dev driver. Both fix a use-after-free after USB-disconnect.
Joakim Zhang's patch improves the flexcan driver, the ECC mechanism is now
completely disabled instead of masking the interrupts.
The next three patches all target the peak_usb driver. Stephane Grosjean's
patch fixes a potential out-of-sync while decoding packets, Johan Hovold's
patch fixes a slab info leak, Jeroen Hofstee's patch adds missing reporting of
bus off recovery events.
Followed by three patches for the c_can driver. Kurt Van Dijck's patch fixes
detection of potential missing status IRQs, Jeroen Hofstee's patches add a chip
reset on open and add missing reporting of bus off recovery events.
Appana Durga Kedareswara rao's patch for the xilinx driver fixes the flags
field initialization for axi CAN.
The next seven patches target the rx-offload helper, they are by me and Jeroen
Hofstee. The error handling in case of a queue overflow is fixed removing a
memory leak. Further the error handling in case of queue overflow and skb OOM
is cleaned up.
The next two patches are by me and target the flexcan and ti_hecc driver. In
case of a error during can_rx_offload_queue_sorted() the error counters in the
drivers are incremented.
Jeroen Hofstee provides 6 patches for the ti_hecc driver, which properly stop
the device in ifdown, improve the rx-offload support (which hit mainline in
v5.4-rc1), and add missing FIFO overflow and state change reporting.
The following four patches target the j1939 protocol. Colin Ian King's patch
fixes a memory leak in the j1939_sk_errqueue() handling. Three patches by
Oleksij Rempel fix a memory leak on socket release and fix the EOMA packet in
the transport protocol.
Timo Schlüßler's patch fixes a potential race condition in the mcp251x driver
on after suspend.
The last patch is by Yegor Yefremov and updates the SPDX-License-Identifier to
v3.0.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yegor Yefremov [Thu, 19 Sep 2019 13:53:04 +0000 (15:53 +0200)]
can: don't use deprecated license identifiers
The "GPL-2.0" license identifier changed to "GPL-2.0-only" in SPDX v3.0.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Timo Schlüßler [Fri, 11 Oct 2019 13:38:19 +0000 (15:38 +0200)]
can: mcp251x: mcp251x_restart_work_handler(): Fix potential force_quit race condition
In mcp251x_restart_work_handler() the variable to stop the interrupt
handler (priv->force_quit) is reset after the chip is restarted and thus
a interrupt might occur.
This patch fixes the potential race condition by resetting force_quit
before enabling interrupts.
Signed-off-by: Timo Schlüßler <schluessler@krause.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oleksij Rempel [Fri, 25 Oct 2019 13:04:13 +0000 (15:04 +0200)]
can: j1939: transport: j1939_xtp_rx_eoma_one(): Add sanity check for correct total message size
We were sending malformed EOMA with total message size set to 0. This
issue has been fixed in the previous patch.
In this patch a sanity check is added to the RX path and a error message
is displayed.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oleksij Rempel [Fri, 25 Oct 2019 13:04:13 +0000 (15:04 +0200)]
can: j1939: transport: j1939_session_fresh_new(): make sure EOMA is send with the total message size set
We were sending malformed EOMA messageswith total message size set to 0.
This patch fixes the bug.
Reported-by: https://github.com/linux-can/can-utils/issues/159
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oleksij Rempel [Thu, 10 Oct 2019 10:50:31 +0000 (12:50 +0200)]
can: j1939: fix memory leak if filters was set
Filters array is coped from user space and linked to the j1939 socket.
On socket release this memory was not freed.
Fixes:
9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Colin Ian King [Wed, 18 Sep 2019 10:11:56 +0000 (11:11 +0100)]
can: j1939: fix resource leak of skb on error return paths
Currently the error return paths do not free skb and this results in a
memory leak. Fix this by freeing them before the return.
Addresses-Coverity: ("Resource leak")
Fixes:
9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 24 Sep 2019 18:46:06 +0000 (18:46 +0000)]
can: ti_hecc: add missing state changes
While the ti_hecc has interrupts to report when the error counters increase
to a certain level and which change state it doesn't handle the case that
the error counters go down again, so the reported state can actually be
wrong. Since there is no interrupt for that, do update state based on the
error counters, when the state is not error active and goes down again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 24 Sep 2019 18:46:03 +0000 (18:46 +0000)]
can: ti_hecc: properly report state changes
The HECC_CANES register handles the flags specially, it only updates
the flags after a one is written to them. Since the interrupt for
frame errors is not enabled an old error can hence been seen when a
state interrupt arrives. For example if the device is not connected
to the CAN-bus the error warning interrupt will have HECC_CANES
indicating there is no ack. The error passive interrupt thereafter
will have HECC_CANES flagging that there is a warning level. And if
thereafter there is a message successfully send HECC_CANES points to
an error passive event, while in reality it became error warning
again. In summary, the state is not always reported correctly.
So handle the state changes and frame errors separately. The state
changes are now based on the interrupt flags and handled directly
when they occur. The reporting of the frame errors is still done as
before, as a side effect of another interrupt.
note: the hecc_clear_bit will do a read, modify, write. So it will
not only clear the bit, but also reset all other bits being set as
a side affect, hence it is replaced with only clearing the flags.
note: The HECC_CANMC_CCR is no longer cleared in the state change
interrupt, it is completely unrelated.
And use net_ratelimit to make checkpatch happy.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 24 Sep 2019 18:46:00 +0000 (18:46 +0000)]
can: ti_hecc: add fifo overflow error reporting
When the rx FIFO overflows the ti_hecc would silently drop them since
the overwrite protection is enabled for all mailboxes. So disable it for
the lowest priority mailbox and return a proper error value when receive
message lost is set. Drop the message itself in that case, since it
might be partially updated.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 24 Sep 2019 18:45:49 +0000 (18:45 +0000)]
can: ti_hecc: release the mailbox a bit earlier
Release the mailbox after reading it, so it can be reused a bit earlier.
Since "can: rx-offload: continue on error" all pending message bits are
cleared directly, so remove clearing them in ti_hecc.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 24 Sep 2019 18:45:56 +0000 (18:45 +0000)]
can: ti_hecc: keep MIM and MD set
The HECC_CANMIM is set in the xmit path and cleared in the interrupt.
Since this is done with a read, modify, write action the register might
end up with some more MIM enabled then intended, since it is not
protected. That doesn't matter at all, since the tx interrupt disables
the mailbox with HECC_CANME (while holding a spinlock). So lets just
always keep MIM set.
While at it, since the mailbox direction never changes, don't set it
every time a message is send, ti_hecc_reset() already sets them to tx.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 24 Sep 2019 18:45:52 +0000 (18:45 +0000)]
can: ti_hecc: ti_hecc_stop(): stop the CPK on down
When the interface goes down, the CPK should no longer take an active
part in the CAN-bus communication, like sending acks and error frames.
So enable configuration mode in ti_hecc_stop, so the CPK is no longer
active.
When a transceiver switch is present the acks and errors don't make it
to the bus, but disabling the CPK then does prevent oddities, like
ti_hecc_reset() failing, since the CPK can become bus-off and starts
counting the 11 bit recessive bits, which seems to block the reset. It
can also cause invalid interrupts and disrupt the CAN-bus, since
transmission can be stopped in the middle of a message, by disabling the
tranceiver while the CPK is sending.
Since the CPK is disabled after normal power on, it is typically only
seen when the interface is restarted.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 15 Jul 2019 18:53:08 +0000 (20:53 +0200)]
can: ti_hecc: ti_hecc_error(): increase error counters if skb enqueueing via can_rx_offload_queue_sorted() fails
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 15 Jul 2019 18:53:08 +0000 (20:53 +0200)]
can: flexcan: increase error counters if skb enqueueing via can_rx_offload_queue_sorted() fails
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 24 Sep 2019 18:45:38 +0000 (18:45 +0000)]
can: rx-offload: can_rx_offload_irq_offload_fifo(): continue on error
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
If the hardware FIFO is empty can_rx_offload_offload_one() will return
NULL.
In case a CAN frame was read from the hardware,
can_rx_offload_offload_one() returns the skb containing it.
Without this patch can_rx_offload_irq_offload_fifo() bails out if no skb
returned, regardless of the reason.
Similar to can_rx_offload_irq_offload_timestamp() in case of a resource
shortage the whole FIFO should be discarded, to avoid an IRQ storm and
give the system some time to recover. However if the FIFO is empty the
loop can be left.
With this patch the loop is left in case of empty FIFO, but not on
errors.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 24 Sep 2019 18:45:38 +0000 (18:45 +0000)]
can: rx-offload: can_rx_offload_irq_offload_timestamp(): continue on error
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
However can_rx_offload_irq_offload_timestamp() bails out in the error
case. In case of a resource shortage all mailboxes should be discarded,
to avoid an IRQ storm and give the system some time to recover.
Since can_rx_offload_irq_offload_timestamp() is typically called from a
while loop, all message will eventually be discarded. So let's continue
on error instead to discard them directly.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 9 Oct 2019 19:00:32 +0000 (21:00 +0200)]
can: rx-offload: can_rx_offload_offload_one(): use ERR_PTR() to propagate error value in case of errors
Before this patch can_rx_offload_offload_one() returns a pointer to a
skb containing the read CAN frame or a NULL pointer.
However the meaning of the NULL pointer is ambiguous, it can either mean
the requested mailbox is empty or there was an error.
This patch fixes this situation by returning:
- pointer to skb on success
- NULL pointer if mailbox is empty
- ERR_PTR() in case of an error
All users of can_rx_offload_offload_one() have been adopted, no
functional change intended.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 9 Oct 2019 13:15:07 +0000 (15:15 +0200)]
can: rx-offload: can_rx_offload_offload_one(): increment rx_fifo_errors on queue overflow or OOM
If the rx-offload skb_queue is full or the skb allocation fails (due to OOM),
the mailbox contents is discarded.
This patch adds the incrementing of the rx_fifo_errors statistics counter.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 9 Oct 2019 14:03:18 +0000 (16:03 +0200)]
can: rx-offload: can_rx_offload_offload_one(): do not increase the skb_queue beyond skb_queue_len_max
The skb_queue is a linked list, holding the skb to be processed in the
next NAPI call.
Without this patch, the queue length in can_rx_offload_offload_one() is
limited to skb_queue_len_max + 1. As the skb_queue is a linked list, no
array or other resources are accessed out-of-bound, however this
behaviour is counterintuitive.
This patch limits the rx-offload skb_queue length to skb_queue_len_max.
Fixes:
d254586c3453 ("can: rx-offload: Add support for HW fifo based irq offloading")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 9 Oct 2019 13:48:48 +0000 (15:48 +0200)]
can: rx-offload: can_rx_offload_queue_tail(): fix error handling, avoid skb mem leak
If the rx-offload skb_queue is full can_rx_offload_queue_tail() will not
queue the skb and return with an error.
This patch frees the skb in case of a full queue, which brings
can_rx_offload_queue_tail() in line with the
can_rx_offload_queue_sorted() function, which has been adjusted in the
previous patch.
The return value is adjusted to -ENOBUFS to better reflect the actual
problem.
The device stats handling is left to the caller.
Fixes:
d254586c3453 ("can: rx-offload: Add support for HW fifo based irq offloading")
Reported-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 9 Oct 2019 13:48:48 +0000 (15:48 +0200)]
can: rx-offload: can_rx_offload_queue_sorted(): fix error handling, avoid skb mem leak
If the rx-offload skb_queue is full can_rx_offload_queue_sorted() will
not queue the skb and return with an error.
None of the callers of this function, issue a kfree_skb() to free the
not queued skb. This results in a memory leak.
This patch fixes the problem by freeing the skb in case of a full queue.
The return value is adjusted to -ENOBUFS to better reflect the actual
problem.
The device stats handling is left to the callers, as this function might
be used in both the rx and tx path.
Fixes:
55059f2b7f86 ("can: rx-offload: introduce can_rx_offload_get_echo_skb() and can_rx_offload_queue_sorted() functions")
Cc: linux-stable <stable@vger.kernel.org>
Cc: Martin Hundebøll <martin@geanix.com>
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Appana Durga Kedareswara rao [Wed, 9 Oct 2019 07:29:47 +0000 (12:59 +0530)]
can: xilinx_can: Fix flags field initialization for axi can
AXI CANIP doesn't support tx fifo empty interrupt feature(TXFEMP),
update the flags filed in the driver for AXI CAN case accordingly.
Fixes:
3281b380ec9f ("can: xilinx_can: Fix flags field initialization for axi can and canps")
Reported-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 1 Oct 2019 21:01:24 +0000 (21:01 +0000)]
can: c_can: C_CAN: add bus recovery events
While the state is updated when the error counters increase and
decrease, there is no event when the bus recovers and the error counters
decrease again. So add that event as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Tested-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 1 Oct 2019 21:01:20 +0000 (21:01 +0000)]
can: c_can: D_CAN: c_can_chip_config(): perform a sofware reset on open
When the CAN interface is closed it the hardwre is put in power down
mode, but does not reset the error counters / state. Reset the D_CAN on
open, so the reported state and the actual state match.
According to [1], the C_CAN module doesn't have the software reset.
[1] http://www.bosch-semiconductors.com/media/ip_modules/pdf_2/c_can_fd8/users_manual_c_can_fd8_r210_1.pdf
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Kurt Van Dijck [Tue, 1 Oct 2019 07:40:36 +0000 (09:40 +0200)]
can: c_can: c_can_poll(): only read status register after status IRQ
When the status register is read without the status IRQ pending, the
chip may not raise the interrupt line for an upcoming status interrupt
and the driver may miss a status interrupt.
It is critical that the BUSOFF status interrupt is forwarded to the
higher layers, since no more interrupts will follow without
intervention.
Thanks to Wolfgang and Joe for bringing up the first idea.
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Joe Burmeister <joe.burmeister@devtank.co.uk>
Fixes:
fa39b54ccf28 ("can: c_can: Get rid of pointless interrupts")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Wed, 25 Sep 2019 08:58:45 +0000 (08:58 +0000)]
can: peak_usb: report bus recovery as well
While the state changes are reported when the error counters increase
and decrease, there is no event when the bus recovers and the error
counters decrease again. So add those as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Johan Hovold [Wed, 23 Oct 2019 08:27:05 +0000 (10:27 +0200)]
can: peak_usb: fix slab info leak
Fix a small slab info leak due to a failure to clear the command buffer
at allocation.
The first 16 bytes of the command buffer are always sent to the device
in pcan_usb_send_cmd() even though only the first two may have been
initialised in case no argument payload is provided (e.g. when waiting
for a response).
Fixes:
bb4785551f64 ("can: usb: PEAK-System Technik USB adapters driver core")
Cc: stable <stable@vger.kernel.org> # 3.4
Reported-by: syzbot+863724e7128e14b26732@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stephane Grosjean [Tue, 8 Oct 2019 08:35:44 +0000 (10:35 +0200)]
can: peak_usb: fix a potential out-of-sync while decoding packets
When decoding a buffer received from PCAN-USB, the first timestamp read in
a packet is a 16-bit coded time base, and the next ones are an 8-bit
offset to this base, regardless of the type of packet read.
This patch corrects a potential loss of synchronization by using a
timestamp index read from the buffer, rather than an index of received
data packets, to determine on the sizeof the timestamp to be read from the
packet being decoded.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Fixes:
46be265d3388 ("can: usb: PEAK-System Technik PCAN-USB specific part")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Joakim Zhang [Thu, 15 Aug 2019 08:00:26 +0000 (08:00 +0000)]
can: flexcan: disable completely the ECC mechanism
The ECC (memory error detection and correction) mechanism can be
activated or not, controlled by the ECCDIS bit in CAN_MECR. When
disabled, updates on indications and reporting registers are stopped.
So if want to disable ECC completely, had better assert ECCDIS bit, not
just mask the related interrupts.
Fixes:
cdce844865be ("can: flexcan: add vf610 support for FlexCAN")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Johan Hovold [Tue, 1 Oct 2019 10:29:14 +0000 (12:29 +0200)]
can: usb_8dev: fix use-after-free on disconnect
The driver was accessing its driver data after having freed it.
Fixes:
0024d8ad1639 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Cc: stable <stable@vger.kernel.org> # 3.9
Cc: Bernd Krumboeck <b.krumboeck@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Johan Hovold [Tue, 1 Oct 2019 10:29:13 +0000 (12:29 +0200)]
can: mcba_usb: fix use-after-free on disconnect
The driver was accessing its driver data after having freed it.
Fixes:
51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Cc: stable <stable@vger.kernel.org> # 4.12
Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Reported-by: syzbot+e29b17e5042bbc56fae9@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Navid Emamdoost [Fri, 20 Sep 2019 02:44:38 +0000 (21:44 -0500)]
can: gs_usb: gs_can_open(): prevent memory leak
In gs_can_open() if usb_submit_urb() fails the allocated urb should be
released.
Fixes:
d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Wen Yang [Sat, 28 Sep 2019 14:29:05 +0000 (22:29 +0800)]
can: dev: add missing of_node_put() after calling of_get_child_by_name()
of_node_put() needs to be called when the device node which is got
from of_get_child_by_name() finished using.
Fixes:
2290aefa2e90 ("can: dev: Add support for limiting configured bitrate")
Cc: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Eric Dumazet [Mon, 4 Nov 2019 15:57:55 +0000 (07:57 -0800)]
dccp: do not leak jiffies on the wire
For some reason I missed the case of DCCP passive
flows in my previous patch.
Fixes:
a904a0693c18 ("inet: stop leaking jiffies on the wire")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Thiemo Nagel <tnagel@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chuhong Yuan [Mon, 4 Nov 2019 15:50:00 +0000 (23:50 +0800)]
net: fec: add missed clk_disable_unprepare in remove
This driver forgets to disable and unprepare clks when remove.
Add calls to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 2 Nov 2019 00:48:11 +0000 (17:48 -0700)]
Merge git://git./linux/kernel/git/netdev/net
Pull networking fixes from David Miller:
1) Fix free/alloc races in batmanadv, from Sven Eckelmann.
2) Several leaks and other fixes in kTLS support of mlx5 driver, from
Tariq Toukan.
3) BPF devmap_hash cost calculation can overflow on 32-bit, from Toke
Høiland-Jørgensen.
4) Add an r8152 device ID, from Kazutoshi Noguchi.
5) Missing include in ipv6's addrconf.c, from Ben Dooks.
6) Use siphash in flow dissector, from Eric Dumazet. Attackers can
easily infer the 32-bit secret otherwise etc.
7) Several netdevice nesting depth fixes from Taehee Yoo.
8) Fix several KCSAN reported errors, from Eric Dumazet. For example,
when doing lockless skb_queue_empty() checks, and accessing
sk_napi_id/sk_incoming_cpu lockless as well.
9) Fix jumbo packet handling in RXRPC, from David Howells.
10) Bump SOMAXCONN and tcp_max_syn_backlog values, from Eric Dumazet.
11) Fix DMA synchronization in gve driver, from Yangchun Fu.
12) Several bpf offload fixes, from Jakub Kicinski.
13) Fix sk_page_frag() recursion during memory reclaim, from Tejun Heo.
14) Fix ping latency during high traffic rates in hisilicon driver, from
Jiangfent Xiao.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (146 commits)
net: fix installing orphaned programs
net: cls_bpf: fix NULL deref on offload filter removal
selftests: bpf: Skip write only files in debugfs
selftests: net: reuseport_dualstack: fix uninitalized parameter
r8169: fix wrong PHY ID issue with RTL8168dp
net: dsa: bcm_sf2: Fix IMP setup for port different than 8
net: phylink: Fix phylink_dbg() macro
gve: Fixes DMA synchronization.
inet: stop leaking jiffies on the wire
ixgbe: Remove duplicate clear_bit() call
Documentation: networking: device drivers: Remove stray asterisks
e1000: fix memory leaks
i40e: Fix receive buffer starvation for AF_XDP
igb: Fix constant media auto sense switching when no cable is connected
net: ethernet: arc: add the missed clk_disable_unprepare
igb: Enable media autosense for the i350.
igb/igc: Don't warn on fatal read failures when the device is removed
tcp: increase tcp_max_syn_backlog max value
net: increase SOMAXCONN to 4096
netdevsim: Fix use-after-free during device dismantle
...
Linus Torvalds [Sat, 2 Nov 2019 00:37:44 +0000 (17:37 -0700)]
Merge tag 'nfs-for-5.4-3' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client bugfixes from Anna Schumaker:
"This contains two delegation fixes (with the RCU lock leak fix marked
for stable), and three patches to fix destroying the the sunrpc back
channel.
Stable bugfixes:
- Fix an RCU lock leak in nfs4_refresh_delegation_stateid()
Other fixes:
- The TCP back channel mustn't disappear while requests are
outstanding
- The RDMA back channel mustn't disappear while requests are
outstanding
- Destroy the back channel when we destroy the host transport
- Don't allow a cached open with a revoked delegation"
* tag 'nfs-for-5.4-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFS: Fix an RCU lock leak in nfs4_refresh_delegation_stateid()
NFSv4: Don't allow a cached open with a revoked delegation
SUNRPC: Destroy the back channel when we destroy the host transport
SUNRPC: The RDMA back channel mustn't disappear while requests are outstanding
SUNRPC: The TCP back channel mustn't disappear while requests are outstanding
Linus Torvalds [Sat, 2 Nov 2019 00:33:12 +0000 (17:33 -0700)]
Merge tag 'for-linus-
20191101' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Two small nvme fixes, one is a fabrics connection fix, the other one
a cleanup made possible by that fix (Anton, via Keith)
- Fix requeue handling in umb ubd (Anton)
- Fix spin_lock_irq() nesting in blk-iocost (Dan)
- Three small io_uring fixes:
- Install io_uring fd after done with ctx (me)
- Clear ->result before every poll issue (me)
- Fix leak of shadow request on error (Pavel)
* tag 'for-linus-
20191101' of git://git.kernel.dk/linux-block:
iocost: don't nest spin_lock_irq in ioc_weight_write()
io_uring: ensure we clear io_kiocb->result before each issue
um-ubd: Entrust re-queue to the upper layers
nvme-multipath: remove unused groups_only mode in ana log
nvme-multipath: fix possible io hang after ctrl reconnect
io_uring: don't touch ctx in setup after ring fd install
io_uring: Fix leaked shadow_req
Linus Torvalds [Sat, 2 Nov 2019 00:20:53 +0000 (17:20 -0700)]
Merge tag 'riscv/for-v5.4-rc6' of git://git./linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"One fix for PCIe users:
- Fix legacy PCI I/O port access emulation
One set of cleanups:
- Resolve most of the warnings generated by sparse across arch/riscv.
No functional changes
And one MAINTAINERS update:
- Update Palmer's E-mail address"
* tag 'riscv/for-v5.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
MAINTAINERS: Change to my personal email address
RISC-V: Add PCIe I/O BAR memory mapping
riscv: for C functions called only from assembly, mark with __visible
riscv: fp: add missing __user pointer annotations
riscv: add missing header file includes
riscv: mark some code and data as file-static
riscv: init: merge split string literals in preprocessor directive
riscv: add prototypes for assembly language functions from head.S
Eric Dumazet [Fri, 1 Nov 2019 03:34:44 +0000 (20:34 -0700)]
powerpc/bpf: Fix tail call implementation
We have seen many crashes on powerpc hosts while loading bpf programs.
The problem here is that bpf_int_jit_compile() does a first pass
to compute the program length.
Then it allocates memory to store the generated program and
calls bpf_jit_build_body() a second time (and a third time
later)
What I have observed is that the second bpf_jit_build_body()
could end up using few more words than expected.
If bpf_jit_binary_alloc() put the space for the program
at the end of the allocated page, we then write on
a non mapped memory.
It appears that bpf_jit_emit_tail_call() calls
bpf_jit_emit_common_epilogue() while ctx->seen might not
be stable.
Only after the second pass we can be sure ctx->seen wont be changed.
Trying to avoid a second pass seems quite complex and probably
not worth it.
Fixes:
ce0761419faef ("powerpc/bpf: Implement support for tail calls")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Sandipan Das <sandipan@linux.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20191101033444.143741-1-edumazet@google.com
Linus Torvalds [Fri, 1 Nov 2019 22:16:25 +0000 (15:16 -0700)]
Merge branch 'parisc-5.4-3' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc fix from Helge Deller:
"Fix a parisc kernel crash with ftrace functions when compiled without
frame pointers"
* 'parisc-5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix frame pointer in ftrace_regs_caller()
David S. Miller [Fri, 1 Nov 2019 22:16:01 +0000 (15:16 -0700)]
Merge branch 'fix-BPF-offload-related-bugs'
Jakub Kicinski says:
====================
fix BPF offload related bugs
test_offload.py catches some recently added bugs.
First of a bug in test_offload.py itself after recent changes
to netdevsim is fixed.
Second patch fixes a bug in cls_bpf, and last one addresses
a problem with the recently added XDP installation optimization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 1 Nov 2019 03:07:00 +0000 (20:07 -0700)]
net: fix installing orphaned programs
When netdevice with offloaded BPF programs is destroyed
the programs are orphaned and removed from the program
IDA - their IDs get released (the programs may remain
accessible via existing open file descriptors and pinned
files). After IDs are released they are set to 0.
This confuses dev_change_xdp_fd() because it compares
the __dev_xdp_query() result where 0 means no program
with prog->aux->id where 0 means orphaned.
dev_change_xdp_fd() would have incorrectly returned success
even though it had not installed the program.
Since drivers already catch this case via bpf_offload_dev_match()
let them handle this case. The error message drivers produce in
this case ("program loaded for a different device") is in fact
correct as the orphaned program must had to be loaded for a
different device.
Fixes:
c14a9f633d9e ("net: Don't call XDP_SETUP_PROG when nothing is changed")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 1 Nov 2019 03:06:59 +0000 (20:06 -0700)]
net: cls_bpf: fix NULL deref on offload filter removal
Commit
401192113730 ("net: sched: refactor block offloads counter
usage") missed the fact that either new prog or old prog may be
NULL.
Fixes:
401192113730 ("net: sched: refactor block offloads counter usage")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 1 Nov 2019 03:06:58 +0000 (20:06 -0700)]
selftests: bpf: Skip write only files in debugfs
DebugFS for netdevsim now contains some "action trigger" files
which are write only. Don't try to capture the contents of those.
Note that we can't use os.access() because the script requires
root.
Fixes:
4418f862d675 ("netdevsim: implement support for devlink region and snapshots")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Thu, 31 Oct 2019 23:24:36 +0000 (16:24 -0700)]
selftests: net: reuseport_dualstack: fix uninitalized parameter
This test reports EINVAL for getsockopt(SOL_SOCKET, SO_DOMAIN)
occasionally due to the uninitialized length parameter.
Initialize it to fix this, and also use int for "test_family" to comply
with the API standard.
Fixes:
d6a61f80b871 ("soreuseport: test mixed v4/v6 sockets")
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Cc: Craig Gallek <cgallek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Thu, 31 Oct 2019 23:10:21 +0000 (00:10 +0100)]
r8169: fix wrong PHY ID issue with RTL8168dp
As reported in [0] at least one RTL8168dp version has problems
establishing a link. This chip version has an integrated RTL8211b PHY,
however the chip seems to report a wrong PHY ID, resulting in a wrong
PHY driver (for Generic Realtek PHY) being loaded.
Work around this issue by adding a hook to r8168dp_2_mdio_read()
for returning the correct PHY ID.
[0] https://bbs.archlinux.org/viewtopic.php?id=246508
Fixes:
242cd9b5866a ("r8169: use phy_resume/phy_suspend")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 31 Oct 2019 22:54:05 +0000 (15:54 -0700)]
net: dsa: bcm_sf2: Fix IMP setup for port different than 8
Since it became possible for the DSA core to use a CPU port different
than 8, our bcm_sf2_imp_setup() function was broken because it assumes
that registers are applicable to port 8. In particular, the port's MAC
is going to stay disabled, so make sure we clear the RX_DIS and TX_DIS
bits if we are not configured for port 8.
Fixes:
9f91484f6fcc ("net: dsa: make "label" property optional for dsa2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 31 Oct 2019 22:42:26 +0000 (15:42 -0700)]
net: phylink: Fix phylink_dbg() macro
The phylink_dbg() macro does not follow dynamic debug or defined(DEBUG)
and as a result, it spams the kernel log since a PR_DEBUG level is
currently used. Fix it to be defined appropriately whether
CONFIG_DYNAMIC_DEBUG or defined(DEBUG) are set.
Fixes:
17091180b152 ("net: phylink: Add phylink_{printk, err, warn, info, dbg} macros")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yangchun Fu [Fri, 1 Nov 2019 17:09:56 +0000 (10:09 -0700)]
gve: Fixes DMA synchronization.
Synces the DMA buffer properly in order for CPU and device to see
the most up-to-data data.
Signed-off-by: Yangchun Fu <yangchun@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 1 Nov 2019 17:32:19 +0000 (10:32 -0700)]
inet: stop leaking jiffies on the wire
Historically linux tried to stick to RFC 791, 1122, 2003
for IPv4 ID field generation.
RFC 6864 made clear that no matter how hard we try,
we can not ensure unicity of IP ID within maximum
lifetime for all datagrams with a given source
address/destination address/protocol tuple.
Linux uses a per socket inet generator (inet_id), initialized
at connection startup with a XOR of 'jiffies' and other
fields that appear clear on the wire.
Thiemo Nagel pointed that this strategy is a privacy
concern as this provides 16 bits of entropy to fingerprint
devices.
Let's switch to a random starting point, this is just as
good as far as RFC 6864 is concerned and does not leak
anything critical.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Thiemo Nagel <tnagel@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 1 Nov 2019 21:50:27 +0000 (14:50 -0700)]
Merge branch '1GbE' of git://git./linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-11-01
This series contains updates to e1000, igb, igc, ixgbe, i40e and driver
documentation.
Lyude Paul fixes an issue where a fatal read error occurs when the
device is unplugged from the machine. So change the read error into a
warn while the device is still present.
Manfred Rudigier found that the i350 device was not apart of the "Media
Auto Sense" feature, yet the device supports it. So add the missing
i350 device to the check and fix an issue where the media auto sense
would flip/flop when no cable was connected to the port causing spurious
kernel log messages.
I fixed an issue where the fix to resolve receive buffer starvation was
applied in more than one place in the driver, one being the incorrect
location in the i40e driver.
Wenwen Wang fixes a potential memory leak in e1000 where allocated
memory is not properly cleaned up in one of the error paths.
Jonathan Neuschäfer cleans up the driver documentation to be consistent
and remove the footnote reference, since the footnote no longer exists in
the documentation.
Igor Pylypiv cleans up a duplicate clearing of a bit, no need to clear
it twice.
v2: Fixed alignment issue in patch 3 of the series based on community
feedback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Pylypiv [Fri, 4 Oct 2019 06:53:57 +0000 (23:53 -0700)]
ixgbe: Remove duplicate clear_bit() call
__IXGBE_RX_BUILD_SKB_ENABLED bit is already cleared.
Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jonathan Neuschäfer [Wed, 2 Oct 2019 15:09:55 +0000 (17:09 +0200)]
Documentation: networking: device drivers: Remove stray asterisks
These asterisks were once references to a line that said:
"* Other names and brands may be claimed as the property of others."
But now, they serve no purpose; they can only irritate the reader.
Fixes:
de3edab4276c ("e1000: update README for e1000")
Fixes:
a3fb65680f65 ("e100.txt: Cleanup license info in kernel doc")
Fixes:
da8c01c4502a ("e1000e.txt: Add e1000e documentation")
Fixes:
f12a84a9f650 ("Documentation: fm10k: Add kernel documentation")
Fixes:
b55c52b1938c ("igb.txt: Add igb documentation")
Fixes:
c4e9b56e2442 ("igbvf.txt: Add igbvf Documentation")
Fixes:
d7064f4c192c ("Documentation/networking/: Update Intel wired LAN driver documentation")
Fixes:
c4b8c01112a1 ("ixgbevf.txt: Update ixgbevf documentation")
Fixes:
1e06edcc2f22 ("Documentation: i40e: Prepare documentation for RST conversion")
Fixes:
105bf2fe6b32 ("i40evf: add driver to kernel build system")
Fixes:
1fae869bcf3d ("Documentation: ice: Prepare documentation for RST conversion")
Fixes:
df69ba43217d ("ionic: Add basic framework for IONIC Network device driver")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Wenwen Wang [Mon, 12 Aug 2019 05:59:21 +0000 (00:59 -0500)]
e1000: fix memory leaks
In e1000_set_ringparam(), 'tx_old' and 'rx_old' are not deallocated if
e1000_up() fails, leading to memory leaks. Refactor the code to fix this
issue.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher [Mon, 7 Oct 2019 22:07:24 +0000 (15:07 -0700)]
i40e: Fix receive buffer starvation for AF_XDP
Magnus's fix to resolve a potential receive buffer starvation for AF_XDP
got applied to both the i40e_xsk_umem_enable/disable() functions, when it
should have only been applied to the "enable". So clean up the undesired
code in the disable function.
CC: Magnus Karlsson <magnus.karlsson@intel.com>
Fixes:
1f459bdc2007 ("i40e: fix potential RX buffer starvation for AF_XDP")
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Manfred Rudigier [Thu, 15 Aug 2019 20:55:20 +0000 (13:55 -0700)]
igb: Fix constant media auto sense switching when no cable is connected
At least on the i350 there is an annoying behavior that is maybe also
present on 82580 devices, but was probably not noticed yet as MAS is not
widely used.
If no cable is connected on both fiber/copper ports the media auto sense
code will constantly swap between them as part of the watchdog task and
produce many unnecessary kernel log messages.
The swap code responsible for this behavior (switching to fiber) should
not be executed if the current media type is copper and there is no signal
detected on the fiber port. In this case we can safely wait until the
AUTOSENSE_EN bit is cleared.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linus Torvalds [Fri, 1 Nov 2019 18:49:54 +0000 (11:49 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Fix two scheduler topology bugs/oversights on Juno r0 2+4 big.LITTLE
systems"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/topology: Allow sched_asym_cpucapacity to be disabled
sched/topology: Don't try to build empty sched domains
Linus Torvalds [Fri, 1 Nov 2019 18:40:47 +0000 (11:40 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc fixes: an ABI fix for a reserved field, AMD IBS fixes, an Intel
uncore PMU driver fix and a header typo fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/headers: Fix spelling s/EACCESS/EACCES/, s/privilidge/privilege/
perf/x86/uncore: Fix event group support
perf/x86/amd/ibs: Handle erratum #420 only on the affected CPU family (10h)
perf/x86/amd/ibs: Fix reading of the IBS OpData register and thus precise RIP validity
perf/core: Start rejecting the syscall with attr.__reserved_2 set
Linus Torvalds [Fri, 1 Nov 2019 18:32:50 +0000 (11:32 -0700)]
Merge branch 'efi-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"Various fixes all over the map: prevent boot crashes on HyperV,
classify UEFI randomness as bootloader randomness, fix EFI boot for
the Raspberry Pi2, fix efi_test permissions, etc"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/efi_test: Lock down /dev/efi_test and require CAP_SYS_ADMIN
x86, efi: Never relocate kernel below lowest acceptable address
efi: libstub/arm: Account for firmware reserved memory at the base of RAM
efi/random: Treat EFI_RNG_PROTOCOL output as bootloader randomness
efi/tpm: Return -EINVAL when determining tpm final events log size fails
efi: Make CONFIG_EFI_RCI2_TABLE selectable on x86 only
David S. Miller [Fri, 1 Nov 2019 17:36:46 +0000 (10:36 -0700)]
Merge tag 'wireless-drivers-2019-11-01' of git://git./linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.4
Third set of fixes for 5.4. Most of them are for iwlwifi but important
fixes also for rtlwifi and mt76, the overflow fix for rtlwifi being
most important.
iwlwifi
* fix merge damage on earlier patch
* various fixes to device id handling
* fix scan config command handling which caused firmware asserts
rtlwifi
* fix overflow on P2P IE handling
* don't deliver too small frames to mac80211
mt76
* disable PCIE_ASPM
* fix buffer DMA unmap on certain cases
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Chuhong Yuan [Fri, 1 Nov 2019 12:17:25 +0000 (20:17 +0800)]
net: ethernet: arc: add the missed clk_disable_unprepare
The remove misses to disable and unprepare priv->macclk like what is done
when probe fails.
Add the missed call in remove.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 1 Nov 2019 17:03:46 +0000 (10:03 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"These are almost exclusively related to CPU errata in CPUs from
Broadcom and Qualcomm where the workarounds were either not being
enabled when they should have been or enabled when they shouldn't have
been.
The only "interesting" fix is ensuring that writeable, shared mappings
are initially mapped as clean since we inadvertently broke the logic
back in v4.14 and then noticed the problem via code inspection the
other day.
The only critical issue we have outstanding is a sporadic NULL
dereference in the scheduler, which doesn't appear to be
arm64-specific and PeterZ is tearing his hair out over it at the
moment.
Summary:
- Enable CPU errata workarounds for Broadcom Brahma-B53
- Enable CPU errata workarounds for Qualcomm Hydra/Kryo CPUs
- Fix initial dirty status of writeable, shared mappings"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: apply ARM64_ERRATUM_843419 workaround for Brahma-B53 core
arm64: Brahma-B53 is SSB and spectre v2 safe
arm64: apply ARM64_ERRATUM_845719 workaround for Brahma-B53 core
arm64: cpufeature: Enable Qualcomm Falkor errata 1009 for Kryo
arm64: cpufeature: Enable Qualcomm Falkor/Kryo errata 1003
arm64: Ensure VM_WRITE|VM_SHARED ptes are clean by default
Linus Torvalds [Fri, 1 Nov 2019 16:54:38 +0000 (09:54 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"generic:
- fix memory leak on failure to create VM
x86:
- fix MMU corner case with AMD nested paging disabled"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: vmx, svm: always run with EFER.NXE=1 when shadow paging is active
kvm: call kvm_arch_destroy_vm if vm creation fails
kvm: Allocate memslots and buses before calling kvm_arch_init_vm
Linus Torvalds [Fri, 1 Nov 2019 16:41:08 +0000 (09:41 -0700)]
Merge tag 'drm-fixes-2019-11-01' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"This is the regular drm fixes pull request for 5.4-rc6. It's a bit
larger than I'd like but then last week was quieter than usual.
The main fixes are amdgpu, and the two bigger area are navi fixes
which are the newest GPU range so still getting actively fixed up, but
also a bunch of clang stack alignment fixes (as amdgpu uses double in
some places).
Otherwise it's all fairly run of the mill fixes, i915, panfrost,
etnaviv, v3d and radeon, along with a core scheduler fix.
Summary:
amdgpu:
- clang alignment fixes
- Updated golden settings
- navi: gpuvm, sdma and display fixes
- Freesync fix
- Gamma fix for DCN
- DP dongle detection fix
- vega10: Fix for undervolting
radeon:
- reenable kexec fix for ppc
scheduler:
- set an error if hw job failed
i915:
- fix PCH reference clock for HSW/BDW
- TGL display PLL doc fix
panfrost:
- warning fix
- runtime pm fix
- bad pointer dereference fix
v3d:
- memleak fix
etnaviv:
- memory corruption fix
- deadlock fix
- reintroduce lost debug message"
* tag 'drm-fixes-2019-11-01' of git://anongit.freedesktop.org/drm/drm: (29 commits)
drm/amdgpu: enable -msse2 for GCC 7.1+ users
drm/amdgpu: fix stack alignment ABI mismatch for GCC 7.1+
drm/amdgpu: fix stack alignment ABI mismatch for Clang
drm/radeon: Fix EEH during kexec
drm/amdgpu/gmc10: properly set BANK_SELECT and FRAGMENT_SIZE
drm/amdgpu/powerplay/vega10: allow undervolting in p7
dc.c:use kzalloc without test
drm/amd/display: setting the DIG_MODE to the correct value.
drm/amd/display: Passive DP->HDMI dongle detection fix
drm/amd/display: add 50us buffer as WA for pstate switch in active
drm/amd/display: Allow inverted gamma
drm/amd/display: do not synchronize "drr" displays
drm/amdgpu: If amdgpu_ib_schedule fails return back the error.
drm/sched: Set error to s_fence if HW job submission failed.
drm/amdgpu/gfx10: update gfx golden settings for navi12
drm/amdgpu/gfx10: update gfx golden settings for navi14
drm/amdgpu/gfx10: update gfx golden settings
drm/amd/display: Change Navi14's DWB flag to 1
drm/amdgpu/sdma5: do not execute 0-sized IBs (v2)
drm/amdgpu: Fix SDMA hang when performing VKexample test
...
Linus Torvalds [Fri, 1 Nov 2019 16:30:48 +0000 (09:30 -0700)]
Merge tag 'pm-5.4-rc6' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix a recently introduced (mostly theoretical) issue that the requests
to confine the maximum CPU frequency coming from the platform firmware
may not be taken into account if multiple CPUs are covered by one
cpufreq policy on a system with ACPI"
* tag 'pm-5.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: processor: Add QoS requests for all CPUs
Linus Torvalds [Fri, 1 Nov 2019 16:21:48 +0000 (09:21 -0700)]
Merge tag 'for-linus' of git://git./linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"A number of bug fixes and a regression fix:
- Various issues from static analysis in hfi1, uverbs, hns, and cxgb4
- Fix for deadlock in a case when the new auto RDMA module loading is
used
- Missing _irq notation in a prior -rc patch found by lockdep
- Fix a locking and lifetime issue in siw
- Minor functional bug fixes in cxgb4, mlx5, qedr
- Fix a regression where vlan interfaces no longer worked with RDMA
CM in some cases"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/hns: Prevent memory leaks of eq->buf_list
RDMA/iw_cxgb4: Avoid freeing skb twice in arp failure case
RDMA/mlx5: Use irq xarray locking for mkey_table
IB/core: Avoid deadlock during netlink message handling
RDMA/nldev: Skip counter if port doesn't match
RDMA/uverbs: Prevent potential underflow
IB/core: Use rdma_read_gid_l2_fields to compare GID L2 fields
RDMA/qedr: Fix reported firmware version
RDMA/siw: free siw_base_qp in kref release routine
RDMA/iwcm: move iw_rem_ref() calls out of spinlock
iw_cxgb4: fix ECN check on the passive accept
IB/hfi1: Use a common pad buffer for 9B and 16B packets
IB/hfi1: Avoid excessive retry for TID RDMA READ request
RDMA/mlx5: Clear old rate limit when closing QP
Linus Torvalds [Fri, 1 Nov 2019 16:18:00 +0000 (09:18 -0700)]
Merge tag 'sound-5.4-rc6' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A couple of regression fixes and a fix for mutex deadlock at
hog-unplug, as well as other device-specific fixes:
- A commit to avoid the spurious unsolicited interrupt on HD-audio
bus caused a stall at shutdown, so it's reverted now.
- The recent support of AMD/Nvidia audio component binding caused a
mutex deadlock; fixed by splitting to another mutex
- The device hot-unplug and the ALSA timer close combo may lead to
another mutex deadlock; fixed by moving put_device() calls
- Usual device-specific small quirks for HD- and USB-audio drivers
- An old error check fix in FireWire driver"
* tag 'sound-5.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: timer: Fix mutex deadlock at releasing card
ALSA: hda - Fix mutex deadlock in HDMI codec driver
Revert "ALSA: hda: Flush interrupts on disabling"
ALSA: bebob: Fix prototype of helper function to return negative value
ALSA: hda/realtek - Fix 2 front mics of codec 0x623
ALSA: hda/realtek - Add support for ALC623
ALSA: usb-audio: Add DSD support for Gustard U16/X26 USB Interface
Trond Myklebust [Thu, 31 Oct 2019 22:40:33 +0000 (18:40 -0400)]
NFS: Fix an RCU lock leak in nfs4_refresh_delegation_stateid()
A typo in nfs4_refresh_delegation_stateid() means we're leaking an
RCU lock, and always returning a value of 'false'. As the function
description states, we were always supposed to return 'true' if a
matching delegation was found.
Fixes:
12f275cdd163 ("NFSv4: Retry CLOSE and DELEGRETURN on NFS4ERR_OLD_STATEID.")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Trond Myklebust [Thu, 31 Oct 2019 22:40:32 +0000 (18:40 -0400)]
NFSv4: Don't allow a cached open with a revoked delegation
If the delegation is marked as being revoked, we must not use it
for cached opens.
Fixes:
869f9dfa4d6d ("NFSv4: Fix races between nfs_remove_bad_delegation() and delegation return")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Florian Fainelli [Thu, 31 Oct 2019 21:47:25 +0000 (14:47 -0700)]
arm64: apply ARM64_ERRATUM_843419 workaround for Brahma-B53 core
The Broadcom Brahma-B53 core is susceptible to the issue described by
ARM64_ERRATUM_843419 so this commit enables the workaround to be applied
when executing on that core.
Since there are now multiple entries to match, we must convert the
existing ARM64_ERRATUM_843419 into an erratum list and use
cpucap_multi_entry_cap_matches to match our entries.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
Florian Fainelli [Thu, 31 Oct 2019 21:47:24 +0000 (14:47 -0700)]
arm64: Brahma-B53 is SSB and spectre v2 safe
Add the Brahma-B53 CPU (all versions) to the whitelists of CPUs for the
SSB and spectre v2 mitigations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
Doug Berger [Thu, 31 Oct 2019 21:47:23 +0000 (14:47 -0700)]
arm64: apply ARM64_ERRATUM_845719 workaround for Brahma-B53 core
The Broadcom Brahma-B53 core is susceptible to the issue described by
ARM64_ERRATUM_845719 so this commit enables the workaround to be applied
when executing on that core.
Since there are now multiple entries to match, we must convert the
existing ARM64_ERRATUM_845719 into an erratum list.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
Dave Airlie [Fri, 1 Nov 2019 01:27:39 +0000 (11:27 +1000)]
Merge tag 'drm-fixes-5.4-2019-10-30' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
drm-fixes-5.4-2019-10-30:
amdgpu:
- clang fixes
- Updated golden settings
- GPUVM fixes for navi
- Navi sdma fix
- Navi display fixes
- Freesync fix
- Gamma fix for DCN
- DP dongle detection fix
- Fix for undervolting on vega10
radeon:
- enable kexec fix for PPC
scheduler:
- set an error on fence if hw job failed
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191030162339.44366-1-alexander.deucher@amd.com
Dave Airlie [Fri, 1 Nov 2019 01:13:35 +0000 (11:13 +1000)]
Merge tag 'drm-intel-fixes-2019-10-31' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix PCH reference clock for FDI on HSW/BDW which was causing users blank screen
- Small documentation fix for TGL display PLLs
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031171209.GA6586@intel.com
Dave Airlie [Fri, 1 Nov 2019 01:09:42 +0000 (11:09 +1000)]
Merge tag 'drm-misc-fixes-2019-10-30-1' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
- three fixes for panfrost, one to silence a warning, one to fix
runtime_pm and one to prevent bogus pointer dereferences
- one fix for a memleak in v3d
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191030182207.evrscl7lnv42u5zu@hendrix
Dave Airlie [Fri, 1 Nov 2019 01:08:24 +0000 (11:08 +1000)]
Merge branch 'etnaviv/fixes' of https://git.pengutronix.de/git/lst/linux into drm-fixes
One memory corruption fix in the MMUv2 GPU coredump code, a deadlock
fix also in the coredump code and reintroduction of a helpful message,
which got dropped by accident in this cycle.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/b0d640267662e3ce5e0089d0afedc1baba55058d.camel@pengutronix.de
Manfred Rudigier [Thu, 15 Aug 2019 20:55:19 +0000 (13:55 -0700)]
igb: Enable media autosense for the i350.
This patch enables the hardware feature "Media Auto Sense" also on the
i350. It works in the same way as on the 82850 devices. Hardware designs
using dual PHYs (fiber/copper) can enable this feature by setting the MAS
enable bits in the NVM_COMPAT register (0x03) in the EEPROM.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lyude Paul [Thu, 22 Aug 2019 18:33:18 +0000 (14:33 -0400)]
igb/igc: Don't warn on fatal read failures when the device is removed
Fatal read errors are worth warning about, unless of course the device
was just unplugged from the machine - something that's a rather normal
occurrence when the igb/igc adapter is located on a Thunderbolt dock. So,
let's only WARN() if there's a fatal read error while the device is
still present.
This fixes the following WARN splat that's been appearing whenever I
unplug my Caldigit TS3 Thunderbolt dock from my laptop:
igb 0000:09:00.0 enp9s0: PCIe link lost
------------[ cut here ]------------
igb: Failed to read reg 0x18!
WARNING: CPU: 7 PID: 516 at
drivers/net/ethernet/intel/igb/igb_main.c:756 igb_rd32+0x57/0x6a [igb]
Modules linked in: igb dca thunderbolt fuse vfat fat elan_i2c mei_wdt
mei_hdcp i915 wmi_bmof intel_wmi_thunderbolt iTCO_wdt
iTCO_vendor_support x86_pkg_temp_thermal intel_powerclamp joydev
coretemp crct10dif_pclmul crc32_pclmul i2c_algo_bit ghash_clmulni_intel
intel_cstate drm_kms_helper intel_uncore syscopyarea sysfillrect
sysimgblt fb_sys_fops intel_rapl_perf intel_xhci_usb_role_switch mei_me
drm roles idma64 i2c_i801 ucsi_acpi typec_ucsi mei intel_lpss_pci
processor_thermal_device typec intel_pch_thermal intel_soc_dts_iosf
intel_lpss int3403_thermal thinkpad_acpi wmi int340x_thermal_zone
ledtrig_audio int3400_thermal acpi_thermal_rel acpi_pad video
pcc_cpufreq ip_tables serio_raw nvme nvme_core crc32c_intel uas
usb_storage e1000e i2c_dev
CPU: 7 PID: 516 Comm: kworker/u16:3 Not tainted 5.2.0-rc1Lyude-Test+ #14
Hardware name: LENOVO 20L8S2N800/20L8S2N800, BIOS N22ET35W (1.12 ) 04/09/2018
Workqueue: kacpi_hotplug acpi_hotplug_work_fn
RIP: 0010:igb_rd32+0x57/0x6a [igb]
Code: 87 b8 fc ff ff 48 c7 47 08 00 00 00 00 48 c7 c6 33 42 9b c0 4c 89
c7 e8 47 45 cd dc 89 ee 48 c7 c7 43 42 9b c0 e8 c1 94 71 dc <0f> 0b eb
08 8b 00 ff c0 75 b0 eb c8 44 89 e0 5d 41 5c c3 0f 1f 44
RSP: 0018:
ffffba5801cf7c48 EFLAGS:
00010286
RAX:
0000000000000000 RBX:
ffff9e7956608840 RCX:
0000000000000007
RDX:
0000000000000000 RSI:
ffffba5801cf7b24 RDI:
ffff9e795e3d6a00
RBP:
0000000000000018 R08:
000000009dec4a01 R09:
ffffffff9e61018f
R10:
0000000000000000 R11:
ffffba5801cf7ae5 R12:
00000000ffffffff
R13:
ffff9e7956608840 R14:
ffff9e795a6f10b0 R15:
0000000000000000
FS:
0000000000000000(0000) GS:
ffff9e795e3c0000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000564317bc4088 CR3:
000000010e00a006 CR4:
00000000003606e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
igb_release_hw_control+0x1a/0x30 [igb]
igb_remove+0xc5/0x14b [igb]
pci_device_remove+0x3b/0x93
device_release_driver_internal+0xd7/0x17e
pci_stop_bus_device+0x36/0x75
pci_stop_bus_device+0x66/0x75
pci_stop_bus_device+0x66/0x75
pci_stop_and_remove_bus_device+0xf/0x19
trim_stale_devices+0xc5/0x13a
? __pm_runtime_resume+0x6e/0x7b
trim_stale_devices+0x103/0x13a
? __pm_runtime_resume+0x6e/0x7b
trim_stale_devices+0x103/0x13a
acpiphp_check_bridge+0xd8/0xf5
acpiphp_hotplug_notify+0xf7/0x14b
? acpiphp_check_bridge+0xf5/0xf5
acpi_device_hotplug+0x357/0x3b5
acpi_hotplug_work_fn+0x1a/0x23
process_one_work+0x1a7/0x296
worker_thread+0x1a8/0x24c
? process_scheduled_works+0x2c/0x2c
kthread+0xe9/0xee
? kthread_destroy_worker+0x41/0x41
ret_from_fork+0x35/0x40
---[ end trace
252bf10352c63d22 ]---
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes:
47e16692b26b ("igb/igc: warn when fatal read failure happens")
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Acked-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eric Dumazet [Wed, 30 Oct 2019 17:05:46 +0000 (10:05 -0700)]
tcp: increase tcp_max_syn_backlog max value
tcp_max_syn_backlog default value depends on memory size
and TCP ehash size. Before this patch, the max value
was 2048 [1], which is considered too small nowadays.
Increase it to 4096 to match the recent SOMAXCONN change.
[1] This is with TCP ehash size being capped to 524288 buckets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Yue Cao <ycao009@ucr.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 30 Oct 2019 16:36:20 +0000 (09:36 -0700)]
net: increase SOMAXCONN to 4096
SOMAXCONN is /proc/sys/net/core/somaxconn default value.
It has been defined as 128 more than 20 years ago.
Since it caps the listen() backlog values, the very small value has
caused numerous problems over the years, and many people had
to raise it on their hosts after beeing hit by problems.
Google has been using 1024 for at least 15 years, and we increased
this to 4096 after TCP listener rework has been completed, more than
4 years ago. We got no complain of this change breaking any
legacy application.
Many applications indeed setup a TCP listener with listen(fd, -1);
meaning they let the system select the backlog.
Raising SOMAXCONN lowers chance of the port being unavailable under
even small SYNFLOOD attack, and reduces possibilities of side channel
vulnerabilities.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Yue Cao <ycao009@ucr.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rafael J. Wysocki [Thu, 31 Oct 2019 20:41:37 +0000 (21:41 +0100)]
Merge branch 'pm-cpufreq'
* pm-cpufreq:
ACPI: processor: Add QoS requests for all CPUs
Björn Töpel [Tue, 29 Oct 2019 15:43:07 +0000 (16:43 +0100)]
bpf: Change size to u64 for bpf_map_{area_alloc, charge_init}()
The functions bpf_map_area_alloc() and bpf_map_charge_init() prior
this commit passed the size parameter as size_t. In this commit this
is changed to u64.
All users of these functions avoid size_t overflows on 32-bit systems,
by explicitly using u64 when calculating the allocation size and
memory charge cost. However, since the result was narrowed by the
size_t when passing size and cost to the functions, the overflow
handling was in vain.
Instead of changing all call sites to size_t and handle overflow at
the call site, the parameter is changed to u64 and checked in the
functions above.
Fixes:
d407bd25a204 ("bpf: don't trigger OOM killer under pressure with map alloc")
Fixes:
c85d69135a91 ("bpf: move memory size checks to bpf_map_charge_init()")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Link: https://lore.kernel.org/bpf/20191029154307.23053-1-bjorn.topel@gmail.com
Björn Töpel [Tue, 1 Oct 2019 11:33:07 +0000 (13:33 +0200)]
samples/bpf: fix build by setting HAVE_ATTR_TEST to zero
To remove that test_attr__{enabled/open} are used by perf-sys.h, we
set HAVE_ATTR_TEST to zero.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: KP Singh <kpsingh@google.com>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: bpf@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: http://lore.kernel.org/bpf/20191001113307.27796-3-bjorn.topel@gmail.com
Björn Töpel [Tue, 1 Oct 2019 11:33:06 +0000 (13:33 +0200)]
perf tools: Make usage of test_attr__* optional for perf-sys.h
For users of perf-sys.h outside perf, e.g. samples/bpf/bpf_load.c, it's
convenient not to depend on test_attr__*.
After commit
91854f9a077e ("perf tools: Move everything related to
sys_perf_event_open() to perf-sys.h"), all users of perf-sys.h will
depend on test_attr__enabled and test_attr__open.
This commit enables a user to define HAVE_ATTR_TEST to zero in order
to omit the test dependency.
Fixes:
91854f9a077e ("perf tools: Move everything related to sys_perf_event_open() to perf-sys.h")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: bpf@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: http://lore.kernel.org/bpf/20191001113307.27796-2-bjorn.topel@gmail.com
Ido Schimmel [Thu, 31 Oct 2019 16:20:30 +0000 (18:20 +0200)]
netdevsim: Fix use-after-free during device dismantle
Commit
da58f90f11f5 ("netdevsim: Add devlink-trap support") added
delayed work to netdevsim that periodically iterates over the registered
netdevsim ports and reports various packet traps via devlink.
While the delayed work takes the 'port_list_lock' mutex to protect
against concurrent addition / deletion of ports, during device creation
/ dismantle ports are added / deleted without this lock, which can
result in a use-after-free [1].
Fix this by making sure that the ports list is always modified under the
lock.
[1]
[ 59.205543] ==================================================================
[ 59.207748] BUG: KASAN: use-after-free in nsim_dev_trap_report_work+0xa67/0xad0
[ 59.210247] Read of size 8 at addr
ffff8883cbdd3398 by task kworker/3:1/38
[ 59.212584]
[ 59.213148] CPU: 3 PID: 38 Comm: kworker/3:1 Not tainted
5.4.0-rc3-custom-16119-ge6abb5f0261e #2013
[ 59.215896] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20180724_192412-buildhw-07.phx2.fedoraproject.org-1.fc29 04/01/2014
[ 59.218384] Workqueue: events nsim_dev_trap_report_work
[ 59.219428] Call Trace:
[ 59.219924] dump_stack+0xa9/0x10e
[ 59.220623] print_address_description.constprop.4+0x21/0x340
[ 59.221976] ? vprintk_func+0x66/0x240
[ 59.222752] __kasan_report.cold.8+0x78/0x91
[ 59.223602] ? nsim_dev_trap_report_work+0xa67/0xad0
[ 59.224603] kasan_report+0xe/0x20
[ 59.225296] nsim_dev_trap_report_work+0xa67/0xad0
[ 59.226435] ? rcu_read_lock_sched_held+0xaf/0xe0
[ 59.227512] ? trace_event_raw_event_rcu_quiescent_state_report+0x360/0x360
[ 59.228851] process_one_work+0x98f/0x1760
[ 59.229684] ? pwq_dec_nr_in_flight+0x330/0x330
[ 59.230656] worker_thread+0x91/0xc40
[ 59.231587] ? process_one_work+0x1760/0x1760
[ 59.232451] kthread+0x34a/0x410
[ 59.233104] ? __kthread_queue_delayed_work+0x240/0x240
[ 59.234141] ret_from_fork+0x3a/0x50
[ 59.234982]
[ 59.235371] Allocated by task 187:
[ 59.236189] save_stack+0x19/0x80
[ 59.236853] __kasan_kmalloc.constprop.5+0xc1/0xd0
[ 59.237822] kmem_cache_alloc_trace+0x14c/0x380
[ 59.238769] __nsim_dev_port_add+0xaf/0x5c0
[ 59.239627] nsim_dev_probe+0x4fc/0x1140
[ 59.240550] really_probe+0x264/0xc00
[ 59.241418] driver_probe_device+0x208/0x2e0
[ 59.242255] __device_attach_driver+0x215/0x2d0
[ 59.243150] bus_for_each_drv+0x154/0x1d0
[ 59.243944] __device_attach+0x1ba/0x2b0
[ 59.244923] bus_probe_device+0x1dd/0x290
[ 59.245805] device_add+0xbac/0x1550
[ 59.246528] new_device_store+0x1f4/0x400
[ 59.247306] bus_attr_store+0x7b/0xa0
[ 59.248047] sysfs_kf_write+0x10f/0x170
[ 59.248941] kernfs_fop_write+0x283/0x430
[ 59.249843] __vfs_write+0x81/0x100
[ 59.250546] vfs_write+0x1ce/0x510
[ 59.251190] ksys_write+0x104/0x200
[ 59.251873] do_syscall_64+0xa4/0x4e0
[ 59.252642] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 59.253837]
[ 59.254203] Freed by task 187:
[ 59.254811] save_stack+0x19/0x80
[ 59.255463] __kasan_slab_free+0x125/0x170
[ 59.256265] kfree+0x100/0x440
[ 59.256870] nsim_dev_remove+0x98/0x100
[ 59.257651] nsim_bus_remove+0x16/0x20
[ 59.258382] device_release_driver_internal+0x20b/0x4d0
[ 59.259588] bus_remove_device+0x2e9/0x5a0
[ 59.260551] device_del+0x410/0xad0
[ 59.263777] device_unregister+0x26/0xc0
[ 59.264616] nsim_bus_dev_del+0x16/0x60
[ 59.265381] del_device_store+0x2d6/0x3c0
[ 59.266295] bus_attr_store+0x7b/0xa0
[ 59.267192] sysfs_kf_write+0x10f/0x170
[ 59.267960] kernfs_fop_write+0x283/0x430
[ 59.268800] __vfs_write+0x81/0x100
[ 59.269551] vfs_write+0x1ce/0x510
[ 59.270252] ksys_write+0x104/0x200
[ 59.270910] do_syscall_64+0xa4/0x4e0
[ 59.271680] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 59.272812]
[ 59.273211] The buggy address belongs to the object at
ffff8883cbdd3200
[ 59.273211] which belongs to the cache kmalloc-512 of size 512
[ 59.275838] The buggy address is located 408 bytes inside of
[ 59.275838] 512-byte region [
ffff8883cbdd3200,
ffff8883cbdd3400)
[ 59.278151] The buggy address belongs to the page:
[ 59.279215] page:
ffffea000f2f7400 refcount:1 mapcount:0 mapping:
ffff8883ecc0ce00 index:0x0 compound_mapcount: 0
[ 59.281449] flags: 0x200000000010200(slab|head)
[ 59.282356] raw:
0200000000010200 ffffea000f2f3a08 ffffea000f2fd608 ffff8883ecc0ce00
[ 59.283949] raw:
0000000000000000 0000000000150015 00000001ffffffff 0000000000000000
[ 59.285608] page dumped because: kasan: bad access detected
[ 59.286981]
[ 59.287337] Memory state around the buggy address:
[ 59.288310]
ffff8883cbdd3280: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 59.289763]
ffff8883cbdd3300: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 59.291452] >
ffff8883cbdd3380: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 59.292945] ^
[ 59.293815]
ffff8883cbdd3400: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 59.295220]
ffff8883cbdd3480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 59.296872] ==================================================================
Fixes:
da58f90f11f5 ("netdevsim: Add devlink-trap support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: syzbot+9ed8f68ab30761f3678e@syzkaller.appspotmail.com
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>