OSDN Git Service
David S. Miller [Wed, 30 Dec 2009 21:51:29 +0000 (13:51 -0800)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6
John W. Linville [Wed, 30 Dec 2009 20:25:08 +0000 (15:25 -0500)]
Merge git://git./linux/kernel/git/linville/wireless-2.6
Conflicts:
drivers/net/wireless/libertas/scan.c
H Hartley Sweeten [Wed, 30 Dec 2009 04:10:35 +0000 (20:10 -0800)]
Subject: drivers/net/sh_eth.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
H Hartley Sweeten [Wed, 30 Dec 2009 04:10:01 +0000 (20:10 -0800)]
drivers/net/r8169.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
H Hartley Sweeten [Wed, 30 Dec 2009 04:09:07 +0000 (20:09 -0800)]
drivers/net/octeon/octeon_mgmt.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
H Hartley Sweeten [Wed, 30 Dec 2009 04:08:09 +0000 (20:08 -0800)]
drivers/net/smc911x.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
H Hartley Sweeten [Wed, 30 Dec 2009 04:07:27 +0000 (20:07 -0800)]
drivers/net/sunvnet.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
H Hartley Sweeten [Wed, 30 Dec 2009 04:06:45 +0000 (20:06 -0800)]
drivers/net/usb/catc.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
H Hartley Sweeten [Wed, 30 Dec 2009 04:05:37 +0000 (20:05 -0800)]
drivers/s390/net/qeth_l2_main.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
H Hartley Sweeten [Wed, 30 Dec 2009 04:04:53 +0000 (20:04 -0800)]
drivers/net/xilinx_emaclite.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
H Hartley Sweeten [Wed, 30 Dec 2009 04:04:14 +0000 (20:04 -0800)]
drivers/net/via-velocity.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
H Hartley Sweeten [Wed, 30 Dec 2009 04:03:28 +0000 (20:03 -0800)]
drivers/net/usb/rtl8150.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
H Hartley Sweeten [Wed, 30 Dec 2009 04:02:29 +0000 (20:02 -0800)]
drivers/net/igbvf/netdev.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
H Hartley Sweeten [Wed, 30 Dec 2009 04:01:46 +0000 (20:01 -0800)]
drivers/net/lib82596.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.
The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation instead of
space-separated.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville [Tue, 29 Dec 2009 19:07:42 +0000 (14:07 -0500)]
Revert "b43: Enforce DMA descriptor memory constraints"
This reverts commit
9bd568a50c446433038dec2a5186c5c57c3dbd23.
That commit is shown to cause allocation failures during initialization
on some machines.
http://bugzilla.kernel.org/show_bug.cgi?id=14844
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Wed, 23 Dec 2009 12:15:47 +0000 (13:15 +0100)]
mac80211: annotate sleeping driver ops
To make it easier to notice cases of calling sleeping ops in atomic context,
annotate driver-ops.h with appropiate might_sleep() calls. At the same time,
also document in mac80211.h the op functions with missing contexts.
mac80211 doesn't seem to use get_tx_stats anywhere currently. Just to be on
the safe side, I documented it to be atomic, but hopefully the op can be
removed in the future.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:15:46 +0000 (13:15 +0100)]
mac80211: remove requeue from work
There's no need to be requeueing the work struct
since we check for the scan after removing items
due to possible timeouts.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:15:45 +0000 (13:15 +0100)]
mac80211: remove struct ieee80211_if_init_conf
All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:
@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:15:44 +0000 (13:15 +0100)]
mac80211/cfg80211: add station events
When, for instance, a new IBSS peer is found, userspace
wants to be notified. Add events for all new stations
that mac80211 learns about.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:15:43 +0000 (13:15 +0100)]
mac80211: make off-channel work generic
This changes mac80211 to allow being off-channel for
any type of work, not just the 'remain-on-channel'
work. This also helps fast transition to a BSS on a
different channel.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:15:42 +0000 (13:15 +0100)]
mac80211: support remain-on-channel command
This implements the new remain-on-channel cfg80211
command in mac80211, extending the work interface.
Also change the work purge code to be able to clean
up events properly (pretending they timed out.)
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Wed, 23 Dec 2009 12:15:41 +0000 (13:15 +0100)]
cfg80211: add remain-on-channel command
Add new commands for requesting the driver to remain awake
on a specified channel for the specified amount of time
(and another command to cancel such an operation). This
can be used to implement userspace-controlled off-channel
operations, like Public Action frame exchange on another
channel than the operation channel.
The off-channel operation should behave similarly to scan,
i.e. the local station (if associated) moves into power
save mode to request the AP to buffer frames for it and
then moves to the other channel to allow the off-channel
operation to be completed. The duration parameter can be
used to request enough time to receive a response from
the target station.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Wed, 23 Dec 2009 12:15:40 +0000 (13:15 +0100)]
mac80211: Generalize off-channel operation helpers from scan code
The off-channel operations for going into power save mode (station
mode) or stop beaconing (AP/IBSS) are not limited to scanning. Move
these into a separate file and allow them to be used for other
purposes, too.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:15:39 +0000 (13:15 +0100)]
mac80211: proper bss private data handling
cfg80211 offers private data for each BSS struct,
which mac80211 uses. However, mac80211 uses internal
and external (cfg80211) BSS pointers interchangeably
and has a hack to put the cfg80211 bss struct into
the private struct.
Remove this hack, properly converting between the
pointers wherever necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:15:38 +0000 (13:15 +0100)]
mac80211: split up and insert custom IEs correctly
Currently, we insert all user-specified IEs before the HT
IE for association, and after the HT IE for probe requests.
For association, that's correct only if the user-specified
IEs are RSN only, incorrect in all other cases including
WPA. Change this to split apart the user-specified IEs in
two places for association: before the HT IE (e.g. RSN),
after the HT IE (generally empty right now I think?) and
after WMM (all other vendor-specific IEs). For probes,
split the IEs in different places to be correct according
to the spec.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:15:37 +0000 (13:15 +0100)]
mac80211: refactor association
Refactor the code to reserve an skb of the right size
(instead of hoping 200 bytes are enough forever), and
also put HT IE generation into an own function.
Additionally, put the HT IE before the vendor-specific
WMM IE. This still leaves things not quite ordered
correctly, due to user-specified IEs, add a note about
that for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:15:36 +0000 (13:15 +0100)]
mac80211: rewrite a few work messages
The station we're authenticating/associating with
may not always be an AP in the sense that word is
mostly understood, so print only the MAC address
of the peer instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:15:35 +0000 (13:15 +0100)]
mac80211: generalise work handling
In order to use auth/assoc for different purposes
other than MLME, it needs to be split up. For other
purposes, a generic work handling (potentially on
another channel) will be useful.
To achieve that, this patch moves much of the MLME
work handling out of mlme into a new work API. The
API can currently handle probing a specific AP,
authentication and association. The MLME previously
handled probe/authentication as one step and will
continue to do so, but they are separate in the new
work handling.
Work items are RCU-managed to be able to check for
existence of an item for a specific frame in the RX
path, but they can be re-used which the MLME right
now will do for its combined probe/auth step.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:15:34 +0000 (13:15 +0100)]
mac80211: generalise management work a bit
As a first step of generalising management work,
this renames a few things and puts more information
directly into the struct so that auth/assoc need
not access the BSS pointer as often -- in fact it
can be removed from auth completely. Also since the
previous patch made sure a new work item is used
for association, we can make the different data a
union.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:15:33 +0000 (13:15 +0100)]
mac80211: let cfg80211 manage auth state
mac80211 currently hangs on to the auth state by
keeping it on the work list. That can lead to
confusing behaviour like rejecting scans while
authenticated to any AP (but not yet associated.)
It also means that it needs to keep track of the
work struct while associated for when it gets
disassociated (or disassociates.)
Change this to free the work struct after the
authentication completed successfully and
allocate a new one for associating, thereby
letting cfg80211 manage the auth state. Another
change necessary for this is to tell cfg80211
about all unicast deauth frames sent to mac80211
since now it can no longer check the auth state,
but that check was racy anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:15:32 +0000 (13:15 +0100)]
mac80211: introduce flush operation
We've long lacked a good confirmation that frames
have really gone out, e.g. before going off-channel
for a scan. Add a flush() operation that drivers
can implement to provide that confirmation, and use
it in a few places:
* before scanning sends the nullfunc frames
* after scanning sends the nullfunc frames, if any
* when going idle, to send any pending frames
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:15:31 +0000 (13:15 +0100)]
mac80211: add ieee80211_sdata_running
Instead of always using netif_running(sdata->dev)
use ieee80211_sdata_running(sdata) now which is
just an inline containing netif_running() for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 22 Dec 2009 23:13:05 +0000 (18:13 -0500)]
rtl8187: remove priv->mode
It is checked in add_interface, but there it is easily replaced with
a check of priv->vif. If that information should become necessary,
it is available in vif->type anyway.
It is also checked in led_turn_on and led_turn_off, where I made the
substitutions as described above. Of course, these checks seem to
have been incorrect since the driver was using NL80211_IFTYPE_MONITOR
to indicate no interface rather than NL80211_IFTYPE_UNSPECIFIED.
Anyway, I think these checks may be extraneous...?
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 22 Dec 2009 23:13:04 +0000 (18:13 -0500)]
rtl8180: remove priv->mode
It is only checked in add_interface, and there it is easily replaced
with a check of priv->vif. If that information should become necessary,
it is available in vif->type anyway.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 22 Dec 2009 23:03:25 +0000 (00:03 +0100)]
rt2x00: Cleanup chip handling helper functions.
Let each of them take a struct rt2x00_dev pointer as argument instead of
a mixture of struct rt2x00_chip and struct rt2x00_dev pointers.
Preparation for further clean ups in the rt2x00 chip handling, especially
for rt2800 devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 22 Dec 2009 23:03:24 +0000 (00:03 +0100)]
rt2x00: convert RT2800PCI_PCI and RT2800PCI_SOC Kconfig symbols to booleans.
There is no need for Kconfig symbols RT2800PCI_PCI and RT2800PCI_SOC to be
tristates, as they are only used to check whether RT2800 PCI or SOC support
is to be compiled in.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 22 Dec 2009 23:03:23 +0000 (00:03 +0100)]
rt2x00: Let rt2800lib check CONFIG_RT2X00_LIB_USB instead of CONFIG_RT2800USB
rt2800lib currently checks whether RT2800USB is enabled in the configuration.
Strictly speaking this is not necessary, it only needs to know whether the
generic rt2x00usb library functions are available. Therefore check for
RT2X00_LIB_USB instead.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 22 Dec 2009 23:03:22 +0000 (00:03 +0100)]
rt2x00: Fix checks for rt2800 SOC support.
Fix checking for SOC support in rt2800pci. The wrong config (an unexisting
one) was checked.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Fri, 18 Dec 2009 22:59:02 +0000 (17:59 -0500)]
wireless: remove CONFIG_WIRELESS_OLD_REGULATORY
This is no longer needed with the availability of
CONFIG_CFG80211_INTERNAL_REGDB.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 11 Dec 2009 13:41:10 +0000 (15:41 +0200)]
wl1271: Prevent performing "join" before association
There is a minor bug in the code causing a "join" to be performed before
there is an intention to associate. Fix this.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 11 Dec 2009 13:41:09 +0000 (15:41 +0200)]
wl1271: Check vif for NULL when indicating beacon-loss
Because the interface is started and the vif are created and destroyed
separately, there is a slim possibility beacon-loss indications occur while
there is no vif - causing a kernel-oops unless checked.
Add checking for the vif.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 11 Dec 2009 13:41:08 +0000 (15:41 +0200)]
wl1271: Add support for acx_pm_config
This acx configures host clock parameters in correspondence with the clock
request line - the settling time of the clock, and whether fast wake-up is
supported.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 11 Dec 2009 13:41:07 +0000 (15:41 +0200)]
wl1271: Change booleans in struct wl1271 into a flags bitmask
For cleaner implementation, change the bunch of booleans in the struct wl1271
structure into a flags bitmask.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 11 Dec 2009 13:41:06 +0000 (15:41 +0200)]
wl1271: Fix supported rate management
Previously, only basic rates were used for data transmission - resulting in
reduced transfer rates. This patch takes enables the firmware to take advantage
of the full set of data rates supported by the AP.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 11 Dec 2009 13:41:05 +0000 (15:41 +0200)]
wl1271: Change rates configured for templates
Previously a "firmware chooses" value was used for the rates of all control
message templates set to the firmware. This resulted in a too high rate to be
chosen to transmit those messages. Change this by configuring a fixed low rate
for the templates.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 11 Dec 2009 13:41:04 +0000 (15:41 +0200)]
wl1271: Add rudimentary ad-hoc support
This patch adds rudimentary a-hoc support for the driver. It will allow
setting up ad-hoc, and for other devices to scan and join. The beacon and probe
response template setting is slightly dirty, and need to be properly
implemented with support from mac80211. Also, the SSID is not configured to the
firmware - the FW will not be able to respond to probe requests autonomously.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 11 Dec 2009 13:41:03 +0000 (15:41 +0200)]
wl1271: Remove beacon-loss-ind from PSM entry failure handling
Remove the beacon-loss indication to stack from PSM entry failure handling -
this will cause more problems than it will solve due to the design of the
mac80211.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 11 Dec 2009 13:41:02 +0000 (15:41 +0200)]
wl1271: Add pre-power-on sleep
This patch adds a short delay before powering on the wl1271. Normally, it is
not needed, but if the wl1271 has been powered off shortly before, for reliable
firmware-booting this small stabilization delay is required.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 11 Dec 2009 13:41:01 +0000 (15:41 +0200)]
wl1271: Implement chipset boot retry
The wl1271 has a hardware bug which causes it to randomly (very infrequently)
to fail powering up properly. This patch implements retry for the chipset boot
sequence, to work around the hardware problem.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 11 Dec 2009 13:41:00 +0000 (15:41 +0200)]
wl1271: prevent power save entry while not associated
The mac80211 sometimes requests power save entry while not associated - this
will cause problems, so prevent it if not associated. Go to powersave once
association is complete.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 11 Dec 2009 13:40:59 +0000 (15:40 +0200)]
wl1271: Fix event acknowledging functionality
In reference source, events are acknowledged separately - fix the driver to
do the same.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 11 Dec 2009 13:40:58 +0000 (15:40 +0200)]
wl1271: Use slow rates for association messages
While not associated, default the data rates to 1 and 2mbps, so that only
those rates will be used for association related message transfer. Once
associated, configure the full rate-set supported by the AP.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 11 Dec 2009 13:40:57 +0000 (15:40 +0200)]
wl1271: Remove smart reflex ACX
Remove the smart-reflex ACX - the associated parameters are now configured
in the radio parameters config.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 11 Dec 2009 13:40:56 +0000 (15:40 +0200)]
wl1271: Configure smart-reflex paramter values.
Configure correct values to be used with the smart-reflex configuration of the
firmware.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 11 Dec 2009 13:40:55 +0000 (15:40 +0200)]
wl1271: use channel 1 when configuring the data path
In the data path configuration, one of the parameters is the channel. We
have been setting it to wl->channel, which is not correct in this case. This
channel has nothing to do with the channel we're currently tuned to, since it
is only used for calibration during this phase. Hardcoded the channel to 1,
according to the reference driver.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 11 Dec 2009 13:40:54 +0000 (15:40 +0200)]
wl1271: some new configuration values according to new reference
In the new reference driver, some of the firmware configuration values have
been changed. This patch changes them in the wl1271 driver accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 11 Dec 2009 13:40:53 +0000 (15:40 +0200)]
wl1271: upload only the first 468 bytes from the NVS file
We were uploading the whole NVS file, but that is wrong, because the same
file also contains the initialization values. For the latest firmwares, we
should upload only the initial 468 bytes from the file.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 11 Dec 2009 13:40:52 +0000 (15:40 +0200)]
wl1271: add gpio_power file in debugfs to power the chip on and off
Some debugging tools require the chip to be powered on before they can work.
With these tools, we shouldn't upload the firmware nor boot the firmware
ourselves, so this debufs file is provided. It always contains the gpio
power setting (0 = off, 1 = on). To change the power setting, just write 0
or 1 to the file.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 11 Dec 2009 13:40:51 +0000 (15:40 +0200)]
wl1271: fix one typo in the rx_rssi_and_proc_compens values
There was a typo in one of the values in the rx_rssi_and_proc_compens elemt
of the Radio Parameters struct.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 11 Dec 2009 13:40:50 +0000 (15:40 +0200)]
wl1271: implement dco itrim parameters setting
Newer firmwares require the dco itrim parameters to be set during
initialization. This patch implements the new ACX function and calls it.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 11 Dec 2009 13:40:49 +0000 (15:40 +0200)]
wl1271: use the correct macro when setting the basic rates
We were using CONF_TX_RATE_MASK_ALL when calling wl1271_acx_rate_policies()
during init. We should use WL1271_DEFAULT_BASIC_RATE_SET instead. The
values are the same, but the latter is just the correct macro to use.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 11 Dec 2009 13:40:48 +0000 (15:40 +0200)]
wl1271: set null data template when BSSID is known
The call to wl1271_cmd_build_null_data() was missing when we got associated,
this was causing PS to fail. This patch adds the call and now PS seems to
work.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 11 Dec 2009 13:40:47 +0000 (15:40 +0200)]
wl1271: check result code from the join command
We were not checking the return value from the call to wl1271_cmd_join().
Added a check to make things more reliable.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 11 Dec 2009 13:40:46 +0000 (15:40 +0200)]
wl1271: limit TX power to 25dBm for every channel
The wl1271 firmware supports maximun 25.5dBm, so the driver was returning
-EINVALID to anything above that. This patch uses the channel max_power
option to limit the TX power to 25dBm.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 11 Dec 2009 13:40:45 +0000 (15:40 +0200)]
wl1271: remove workaround for disconnection
Now we're using a the idle information coming from mac80211 to decide when to
disconnect. If we have joined (ie. we're listening to a channel), whenever
the interface goes to idle, we will issue a disconnect command. So the
workaround to send a disconnect command before joining is not needed anymore.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 11 Dec 2009 13:40:44 +0000 (15:40 +0200)]
wl1271: use join command with dummy BSSID
When we need to change the channel before association, we have to send a join
command with a valid BSSID. With this patch we use
0baddeadbeef as the
BSSID. There are ongoing discussions with TI to get this done in a cleaner
way.
When we go back to idle, we issue a CMD_DISCONNECT to make sure the firmware
stops listening to the channel and cleans things up internally.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 11 Dec 2009 13:40:43 +0000 (15:40 +0200)]
wl1271: added radio parameters configuration values newer firmwares
Add new radio parameters for new structures based on firmware revision
6.1.0.0.288.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 11 Dec 2009 13:40:42 +0000 (15:40 +0200)]
wl1271: update radio and general parameters values
There were some changes in the values we have to use for these settings. This
patches updates them.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 11 Dec 2009 13:40:41 +0000 (15:40 +0200)]
wl1271: updated general parameters structure for newer firmwares
In revision 6.1.0.0.288 the general parameters structure has changed. This
patch updates the driver code accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 11 Dec 2009 13:40:40 +0000 (15:40 +0200)]
wl1271: updated radio parameters structure for newer firmwares
In revision 6.1.0.0.288 the radio parameters structure has changed. This
patch updates the driver code accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Thu, 10 Dec 2009 23:35:01 +0000 (17:35 -0600)]
b43: Allow PIO mode to be selected at module load
If userencounter the "Fatal DMA Problem" with a BCM43XX device, and
still wish to use b43 as the driver, their only option is to rebuild
the kernel with CONFIG_B43_FORCE_PIO. This patch removes this option and
allows PIO mode to be selected with a load-time parameter for the module.
Note that the configuration variable CONFIG_B43_PIO is also removed.
Once the DMA problem with the BCM4312 devices is solved, this patch will
likely be reverted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:33:09 +0000 (18:33 +0100)]
mwl8k: remove duplicate local per-vif copy of ieee80211_bss_conf
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:33:04 +0000 (18:33 +0100)]
mwl8k: remove unused mwl8k_vif::priv
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:32:54 +0000 (18:32 +0100)]
mwl8k: fix up AP vs. STA firmware image receive descriptor handling
The receive descriptor ops that are currently marked as being for
8687 only are actually used for all STA firmware images, whereas the
receive descriptor ops marked as 8366 are only used on 8366 when an
AP firmware image is in use.
Rename the receive descriptor ops to reflect this, use the STA ops
unconditionally if the firmware image loaded reported the STA ready
code, and rename the mwl8k_device_info::rxd_ops member to ap_rxd_ops
to indicate that it should only be used if we are running on AP
firmware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:32:46 +0000 (18:32 +0100)]
mwl8k: do rx/tx ring initialisation after loading firmware
Whether the firmware we have loaded is AP or STA firmware decides
which receive descriptor format we have to use. Therefore, move
rx/tx ring initialisation to be after firmware loading.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:32:38 +0000 (18:32 +0100)]
mwl8k: get rid of the struct mwl8k_firmware abstraction
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:32:20 +0000 (18:32 +0100)]
mwl8k: add 2.4GHz channels 12, 13 and 14
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:32:13 +0000 (18:32 +0100)]
mwl8k: initialize the mwl8k_info_tbl table using the MWL* enums
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:32:00 +0000 (18:32 +0100)]
mwl8k: inline qos field manipulation functions
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:31:52 +0000 (18:31 +0100)]
mwl8k: get rid of the AMSDU check in the transmit path
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:31:40 +0000 (18:31 +0100)]
mwl8k: hw is never NULL in mwl8k_set_radio_preamble()
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:31:33 +0000 (18:31 +0100)]
mwl8k: firmware command code cleanup
Sort firmware commands by command code, get rid of the 802_11 substring
in all command names, and make sure that the command functions match the
firmware command names.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Mon, 28 Dec 2009 06:23:11 +0000 (14:23 +0800)]
iwmc3200wifi: fix array out-of-boundary access
Allocate priv->rx_packets[IWM_RX_ID_HASH + 1] because the max array
index is IWM_RX_ID_HASH according to IWM_RX_ID_GET_HASH().
Cc: stable@kernel.org
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roel Kluin [Sat, 26 Dec 2009 19:31:59 +0000 (20:31 +0100)]
wl1251: timeout one too soon in wl1251_boot_run_firmware()
`loop' reaches INIT_LOOP + 1 after the loop. so if ACX_INTR_INIT_COMPLETE
occurs in the last iteration the write occurs but also the error out as if a
timeout occurred. This is probably very unlikely to ever occur.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 24 Dec 2009 20:38:22 +0000 (15:38 -0500)]
mac80211: fix propagation of failed hardware reconfigurations
mac80211 does not propagate failed hardware reconfiguration
requests. For suspend and resume this is important due to all
the possible issues that can come out of the suspend <-> resume
cycle. Not propagating the error means cfg80211 will assume
the resume for the device went through fine and mac80211 will
continue on trying to poke at the hardware, enable timers,
queue work, and so on for a device which is completley
unfunctional.
The least we can do is to propagate device start issues and
warn when this occurs upon resume. A side effect of this patch
is we also now propagate the start errors upon harware
reconfigurations (non-suspend), but this should also be desirable
anyway, there is not point in continuing to reconfigure a
device if mac80211 was unable to start the device.
For further details refer to the thread:
http://marc.info/?t=
126151038700001&r=1&w=2
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 24 Dec 2009 20:26:09 +0000 (15:26 -0500)]
mac80211: fix race with suspend and dynamic_ps_disable_work
When mac80211 suspends it calls a driver's suspend callback
as a last step and after that the driver assumes no calls will
be made to it until we resume and its start callback is kicked.
If such calls are made, however, suspend can end up throwing
hardware in an unexpected state and making the device unusable
upon resume.
Fix this by preventing mac80211 to schedule dynamic_ps_disable_work
by checking for when mac80211 starts to suspend and starts
quiescing. Frames should be allowed to go through though as
that is part of the quiescing steps and we do not flush the
mac80211 workqueue since it was already done towards the
beginning of suspend cycle.
The other mac80211 issue will be hanled in the next patch.
For further details see refer to the thread:
http://marc.info/?t=
126144866100001&r=1&w=2
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 24 Dec 2009 13:04:32 +0000 (14:04 +0100)]
ath9k: fix missed error codes in the tx status check
My previous change added in:
commit
815833e7ecf0b9a017315cae6aef4d7cd9517681
ath9k: fix tx status reporting
was not checking all possible tx error conditions. This could possibly
lead to throughput issues due to slow rate control adaption or missed
retransmissions of failed A-MPDU frames.
This patch adds a mask for all possible error conditions and uses it
in the xmit ok check.
Cc: stable@kernel.org
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 24 Dec 2009 01:03:29 +0000 (20:03 -0500)]
ath9k: wake hardware during AMPDU TX actions
AMDPDU actions poke hardware for TX operation, as such
we want to turn hardware on for these actions. AMDPU RX operations
do not require hardware on as nothing is done in hardware for
those actions. Without this we cannot guarantee hardware has
been programmed correctly for each AMPDU TX action.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 24 Dec 2009 01:03:28 +0000 (20:03 -0500)]
ath9k: wake hardware for interface IBSS/AP/Mesh removal
When we remove a IBSS/AP/Mesh interface we stop DMA
but to do this we should ensure hardware is on. Awaken
the device prior to these calls. This should ensure
DMA is stopped upon suspend and plain device removal.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Thu, 24 Dec 2009 01:03:27 +0000 (20:03 -0500)]
ath9k: fix suspend by waking device prior to stop
Ensure the device is awake prior to trying to tell hardware
to stop it. Impact of not doing this is we can likely leave
the device in an undefined state likely causing issues with
suspend and resume. This patch ensures harware is where it
should be prior to suspend.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 14:33:35 +0000 (15:33 +0100)]
cfg80211: fix error path in cfg80211_wext_siwscan
If there's an invalid channel or SSID, the code leaks
the scan request. Always free the scan request, unless
it was successfully given to the driver.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Wed, 23 Dec 2009 13:23:19 +0000 (15:23 +0200)]
wl1271_cmd.c: cleanup char => u8
This is just a clean up and doesn't make a functional difference. It keeps the
lint checkers happy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tobias Klauser [Wed, 23 Dec 2009 13:18:11 +0000 (14:18 +0100)]
iwlwifi: Storage class should be before const qualifier
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tobias Klauser [Wed, 23 Dec 2009 13:04:43 +0000 (14:04 +0100)]
ath9k: Storage class should be before const qualifier
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:12:05 +0000 (13:12 +0100)]
cfg80211: fix race between deauth and assoc response
Joseph Nahmias reported, in http://bugs.debian.org/562016,
that he was getting the following warning (with some log
around the issue):
ath0: direct probe to AP 00:11:95:77:e0:b0 (try 1)
ath0: direct probe responded
ath0: authenticate with AP 00:11:95:77:e0:b0 (try 1)
ath0: authenticated
ath0: associate with AP 00:11:95:77:e0:b0 (try 1)
ath0: deauthenticating from 00:11:95:77:e0:b0 by local choice (reason=3)
ath0: direct probe to AP 00:11:95:77:e0:b0 (try 1)
ath0: RX AssocResp from 00:11:95:77:e0:b0 (capab=0x421 status=0 aid=2)
ath0: associated
------------[ cut here ]------------
WARNING: at net/wireless/mlme.c:97 cfg80211_send_rx_assoc+0x14d/0x152 [cfg80211]()
Hardware name: 7658CTO
...
Pid: 761, comm: phy0 Not tainted 2.6.32-trunk-686 #1
Call Trace:
[<
c1030a5d>] ? warn_slowpath_common+0x5e/0x8a
[<
c1030a93>] ? warn_slowpath_null+0xa/0xc
[<
f86cafc7>] ? cfg80211_send_rx_assoc+0x14d/0x152
...
ath0: link becomes ready
ath0: deauthenticating from 00:11:95:77:e0:b0 by local choice (reason=3)
ath0: no IPv6 routers present
ath0: link is not ready
ath0: direct probe to AP 00:11:95:77:e0:b0 (try 1)
ath0: direct probe responded
ath0: authenticate with AP 00:11:95:77:e0:b0 (try 1)
ath0: authenticated
ath0: associate with AP 00:11:95:77:e0:b0 (try 1)
ath0: RX ReassocResp from 00:11:95:77:e0:b0 (capab=0x421 status=0 aid=2)
ath0: associated
It is not clear to me how the first "direct probe" here
happens, but this seems to be a race condition, if the
user requests to deauth after requesting assoc, but before
the assoc response is received. In that case, it may
happen that mac80211 tries to report the assoc success to
cfg80211, but gets blocked on the wdev lock that is held
because the user is requesting the deauth.
The result is that we run into a warning. This is mostly
harmless, but maybe cause an unexpected event to be sent
to userspace; we'd send an assoc success event although
userspace was no longer expecting that.
To fix this, remove the warning and check whether the
race happened and in that case abort processing.
Reported-by: Joseph Nahmias <joe@nahmias.net>
Cc: stable@kernel.org
Cc: 562016-quiet@bugs.debian.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:12:04 +0000 (13:12 +0100)]
wireless: remove remaining qual code
This removes the remaining users of the rx status
'qual' field and the field itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 22 Dec 2009 23:03:21 +0000 (00:03 +0100)]
rt2x00: Add USB ID for Linksys WUSB 600N rev 2.
This is a rt2870 based device.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Tue, 22 Dec 2009 03:26:48 +0000 (22:26 -0500)]
ath5k: fix SWI calibration interrupt storm
The calibration period is now invoked by triggering a software
interrupt from within the ISR by ath5k_hw_calibration_poll()
instead of via a timer.
However, the calibration interval isn't initialized before
interrupts are enabled, so we can have a situation where an
interrupt occurs before the interval is assigned, so the
interval is actually negative. As a result, the ISR will
arm a software interrupt to schedule the tasklet, and then
rearm it when the SWI is processed, and so on, leading to a
softlockup at modprobe time.
Move the initialization order around so the calibration interval
is set before interrupts are active. Another possible fix
is to schedule the tasklet directly from the poll routine,
but I think there are additional plans for the SWI.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 20 Dec 2009 18:07:09 +0000 (19:07 +0100)]
mac80211: fix ibss join with fixed-bssid
When fixed bssid is requested when joining an ibss network, incoming
beacons that match the configured bssid cause mac80211 to create new
sta entries, even before the ibss interface is in joined state.
When that happens, it fails to bring up the interface entirely, because
it checks for existing sta entries before joining.
This patch fixes this bug by refusing to create sta info entries before
the interface is fully operational.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Samuel Ortiz [Fri, 18 Dec 2009 10:36:49 +0000 (11:36 +0100)]
libertas: Remove carrier signaling from the scan code
There is no reason to signal a carrier off when doing a 802.11 scan.
Cc: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>