OSDN Git Service
Lukas Wunner [Sun, 10 Jan 2016 23:08:35 +0000 (00:08 +0100)]
apple-gmux: Add initial documentation
Document what I've learned so far about the gmux so that we can
collaboratively reverse-engineer its remaining unknown bits
without everyone having to start from scratch.
The DOC sections are bound together in the gpu.tmpl DocBook
under a new vga_switcheroo "Handlers" chapter. Eventually
this should be amended with documentation about the four other
handlers that exist so far (nouveau v1 DSM, nouveau Optimus DSM,
radeon ATPX, amdgpu ATPX).
Requires kernel-doc with asciidoc support.
The EFI variable was reverse-engineered by Bruno Bierbaumer
<bruno@bierbaumer.net> and Andreas Heider <andreas@meetr.de>.
Some of the remaining open questions:
* How are vblank intervals synchronized on retinas to achieve seamless
switching? Is the DP mux capable of this? It's not mentioned in the
data sheets. Or is it done at the OS level, i.e. do we have to
synchronize vblank intervals between DRM drivers? There's a signal
coming from the panel connector and going into gmux, could this be
the vblank signal as received by the panel to properly time the
switch?
* On retinas there's an I2C bus between gmux and the connector of the
right I/O board, apparently leading to the Parade PS8401A HDMI
repeater. What is this for, is it controlled via gmux registers?
Data sheet:
http://www.paradetech.com/products/jitter-cleaning-repeaters/ps8401/
* On retinas there's an I2C bus between gmux and the LED driver.
Pre-retinas connected the LED driver to SMBUS. Are there additional
gmux registers on retinas to control it?
* The MacPro6,1 2013 also has a gmux, the same Renesas R4F2113 as the
retina MacBook Pro. The Mac Pro doesn't have a built-in display,
so what is its purpose? Power control of the dual FirePro GPUs?
Switching of the external DP/Thunderbolt ports? The iFixit teardown
clearly shows one TI HD3SS212 DisplayPort mux on the logic board next
to one of the three Thunderbolt controllers. However six muxes would
be necessary to switch all six ports between GPUs. The mux is probably
necessary for one of the display configurations allowed by Apple,
but which one?
https://www.ifixit.com/Teardown/Mac+Pro+Late+2013+Teardown/20778
https://d3nevzfk7ii3be.cloudfront.net/igi/fELBTnt31QhnDsqq.huge
https://support.apple.com/en-us/HT202801
* Registers we haven't decoded yet:
0x700 32 Bit configmap?
0x708 32 Bit power sequence?
0x712 8 Bit status of clock from panel on retinas?
0x713 8 Bit dito?
0x724 16 Bit backlight, raw value?
0x760 32 Bit backlight
0x764 32 Bit backlight
0x768 8 Bit backlight
0x76a 16 Bit backlight
0x76c 16 Bit backlight
0x76e 16 Bit backlight
0x77f edp/dp/hdmi probe? retina only.
* Addition by Bruno Prémont <bonbons@linux-vserver.org>:
"Missing is also precise knowledge as to what the gmux depends on.
From behavioral reports, it is somehow sensitive to VGA IO/MEM
routing (it apparently needs the routing to go to integrated GPU,
not discrete GPU).
When the routing is inappropriate backlight control IO just reads back
as 0xFF (and eventually gmux IO in general does so)."
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/da309e436fbeac886477d80376457b7d83ea4b2d.1452431795.git.lukas@wunner.de
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dan Carpenter [Fri, 8 Jan 2016 11:00:45 +0000 (14:00 +0300)]
drm: move MODULE_PARM_DESC to other file
We moved the module options from drm_drv.c to drm_irq.c in
18882995713d
('drm: Move vblank related module options into drm_irq.c'). Let's move
the MODULE_PARM_DESC()s as well so they're together.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160108110045.GF32195@mwanda
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Fri, 8 Jan 2016 11:21:51 +0000 (13:21 +0200)]
drm/edid: index CEA/HDMI mode tables using the VIC
Add a dummy entry to CEA/HDMI mode tables so they can be indexed
directly using the VIC, avoiding a +1/-1 dance here and there. This adds
clarity to the error checking for various functions that return the VIC
on success and zero on failure; we can now explicitly check for 0
instead of just subtracting one from an unsigned type.
Also add drm_valid_cea_vic() and drm_valid_hdmi_vic() helpers for
checking valid VICs.
v2: add drm_valid_cea_vic and drm_valid_hdmi_vic helpers (Ville)
use { } instead of { 0 } for initializing the dummy modes
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452252111-6439-1-git-send-email-jani.nikula@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Maarten Lankhorst [Mon, 4 Jan 2016 11:53:20 +0000 (12:53 +0100)]
drm/atomic: Remove drm_atomic_connectors_for_crtc.
Now that connector_mask is reliable there's no need for this
function any more.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1451908400-25147-6-git-send-email-maarten.lankhorst@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Maarten Lankhorst [Wed, 6 Jan 2016 13:53:25 +0000 (14:53 +0100)]
drm/i915: Update connector_mask during readout, v2.
drm/i915: Update connector_mask during readout, v2.
The connector_mask may be used any time during the non-atomic
.crtc_disable which is called before the full atomic state is
set up and needs to be accurate for that reason.
Changes since v1:
- Update connector_mask in readout_hw_state and add a comment.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/568D1C55.8010001@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Tue, 5 Jan 2016 09:42:31 +0000 (09:42 +0000)]
drm: Remove opencoded drm_gem_object_release_handle()
drm_gem_handle_delete() contains its own version of
drm_gem_object_release_handle(), so lets just call the release method
instead.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1451986951-3703-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Tue, 5 Jan 2016 09:42:30 +0000 (09:42 +0000)]
drm: Do not set outparam on error during GEM handle allocation
Good practice dictates that we do not leak stale information to our
callers, and should avoid overwriting an outparam on an error path.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1451986951-3703-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Mon, 4 Jan 2016 06:53:36 +0000 (07:53 +0100)]
drm/docs: more leftovers from the big vtable documentation pile
Another pile of vfuncs from the old gpu.tmpl xml documentation that
I've forgotten to delete. I spotted a few more things to
clarify/extend in the new kerneldoc while going through this once
more.
v2: Spelling fixes (Thierry).
v3: More spelling fixes and use Thierry's proposal to clarify why
drivers need to validate modes both in ->mode_fixup and ->mode_valid.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Daniel Vetter [Tue, 8 Dec 2015 08:49:20 +0000 (09:49 +0100)]
drm/atomic-helper: Reject legacy flips on a disabled pipe
We want this for consistency with existing page_flip semantics.
Since this spurred quite a discussion on IRC also document why we
reject event generation when the pipe is off: It's not that it's hard
to implement, but userspace has a track recording which proves that it's
way too easy to accidentally abuse and cause havoc. We want to make
sure userspace doesn't get away with that.
v2: Somehow thought we do reject events already, but that code only
existed in my imagination ... Also suggestions from Thierry.
Cc: Daniel Stone <daniels@collabora.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449564561-3896-4-git-send-email-daniel.vetter@ffwll.ch
Maarten Lankhorst [Mon, 4 Jan 2016 11:53:18 +0000 (12:53 +0100)]
drm/atomic: add connector mask to drm_crtc_state.
It can be useful to iterate over connectors without grabbing
connection_mutex. It can also be used to see how many connectors
are on a crtc without iterating over the list.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1451908400-25147-4-git-send-email-maarten.lankhorst@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Maarten Lankhorst [Mon, 4 Jan 2016 11:53:17 +0000 (12:53 +0100)]
drm/tegra: Use __drm_atomic_helper_reset_connector for subclassing connector state, v2.
Changes since v1:
- Do not reset if state allocation fails.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com> #irc
Link: http://patchwork.freedesktop.org/patch/msgid/1451908400-25147-3-git-send-email-maarten.lankhorst@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Maarten Lankhorst [Mon, 4 Jan 2016 11:53:16 +0000 (12:53 +0100)]
drm/atomic: Add __drm_atomic_helper_connector_reset, v2.
This is useful for drivers that subclass connector_state, like tegra.
Changes since v1:
- Docbook updates.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1451908400-25147-2-git-send-email-maarten.lankhorst@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Maarten Lankhorst [Mon, 4 Jan 2016 11:53:15 +0000 (12:53 +0100)]
drm/i915: Set connector_state->connector using the helper.
The atomic helper sets connector_state->connector, which the i915
code didn't. This will become a problem when we start using it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1451908400-25147-1-git-send-email-maarten.lankhorst@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 4 Jan 2016 10:11:01 +0000 (10:11 +0000)]
drm: Use a normal idr allocation for the obj->name
Unlike the handle, the name table uses a sleeping mutex rather than a
spinlock. The allocation is in a normal context, and we can use the
simpler sleeping gfp_t, rather than have to take from the atomic
reserves.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1451902261-25380-3-git-send-email-chris@chris-wilson.co.uk
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 4 Jan 2016 10:11:00 +0000 (10:11 +0000)]
drm: Only bump object-reference count when adding first handle
We only need a single reference count for all handles (i.e. non-zero
obj->handle_count) and so can trim a few atomic operations by only
taking the reference on the first handle and dropping it after the last.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1451902261-25380-2-git-send-email-chris@chris-wilson.co.uk
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 4 Jan 2016 10:10:59 +0000 (10:10 +0000)]
drm: Balance error path for GEM handle allocation
The current error path for failure when establishing a handle for a GEM
object is unbalance, e.g. we call object_close() without calling first
object_open(). Use the typical onion structure to only undo what has
been set up prior to the error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Lukas Wunner [Sat, 2 Jan 2016 17:47:17 +0000 (18:47 +0100)]
vga_switcheroo: Prettify documentation
Fix indentation of vga_switcheroo sections in gpu.tmpl.
Change section type of API documentation from "chapter" to "sect1"
so that the individual functions no longer clutter up the ToC.
Group together under a new "API" chapter.
Fix wording "heretoforth" -> "henceforth".
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Julia Lawall [Wed, 30 Dec 2015 21:20:30 +0000 (22:20 +0100)]
drm/dp/mst: constify drm_dp_mst_topology_cbs structures
The drm_dp_mst_topology_cbs structures are never modified, so declare them
as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Geliang Tang [Sun, 27 Dec 2015 10:45:58 +0000 (18:45 +0800)]
drm/gma500: use to_pci_dev()
Use to_pci_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Matt Roper [Sat, 19 Dec 2015 01:27:01 +0000 (17:27 -0800)]
drm/fb-helper: Use proper plane mask for fb cleanup
pan_display_atomic() calls drm_atomic_clean_old_fb() to sanitize the
legacy FB fields (plane->fb and plane->old_fb). However it was building
the plane mask to pass to this function incorrectly (the bitwise OR was
using plane indices rather than plane masks). The end result was that
sometimes the legacy pointers would become out of sync with the atomic
pointers. If another operation tried to re-set the same FB onto the
plane, we might end up with the pointers back in sync, but improper
reference counts, which would eventually lead to system crashes when we
accessed a pointer to a prematurely-destroyed FB.
The cause here was a very subtle bug introduced in commit:
commit
07d3bad6c1210bd21e85d084807ef4ee4ac43a78
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Wed Nov 11 11:29:11 2015 +0100
drm/core: Fix old_fb handling in pan_display_atomic.
I found the crashes were most easily reproduced (on i915 at least) by
starting X and then VT switching to a VT that wasn't running a console
instance...the sequence of vt/fbcon entries that happen in that case
trigger a reference count mismatch and crash the system.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93313
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Nicolas Iooss [Fri, 11 Dec 2015 10:20:28 +0000 (11:20 +0100)]
drm: use dev_name as default unique name in drm_dev_alloc()
The following code pattern exists in some DRM drivers:
ddev = drm_dev_alloc(&driver, parent_dev);
drm_dev_set_unique(ddev, dev_name(parent_dev));
(Sometimes dev_name(ddev->dev) is used, which is the same.)
As suggested in
http://lists.freedesktop.org/archives/dri-devel/2015-December/096441.html,
the unique name of a new DRM device can be set as dev_name(parent_dev)
when parent_dev is not NULL (vgem is a special case).
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Nicolas Iooss [Fri, 11 Dec 2015 10:20:27 +0000 (11:20 +0100)]
drm: make drm_dev_set_unique() not use a format string
drm_dev_set_unique() uses a format string to define the unique name of a
device. This feature is not used as currently all the calls to this
function either use "%s" as a format string or directly use
dev_name().
Even though this second kind of call does not introduce security
problems, because there cannot be "%" characters in dev_name() results,
gcc issues a warning when building with -Wformat-security flag
("warning: format string is not a string literal (potentially
insecure)"). This warning is useful to find real bugs like the one
fixed by commit
3958b79266b1 ("configfs: fix kernel infoleak through
user-controlled format string"). False positives which do not bring
an extra value make the work of finding real bugs harder.
Therefore remove the format-string feature from drm_dev_set_unique().
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1449829228-4425-1-git-send-email-nicolas.iooss_linux@m4x.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:21:15 +0000 (12:21 +0100)]
drm/vmwgfx: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/vmwgfx/vmwgfx.ko:
-.text 132244
+.text 132240
-.rodata 18296
+.rodata 18680
-.data 5096
+.data 4712
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-28-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:21:14 +0000 (12:21 +0100)]
drm/udl: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/udl/udl.ko:
-.text 11336
+.text 11332
-.rodata 560
+.rodata 684
-.data 696
+.data 572
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-27-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:21:13 +0000 (12:21 +0100)]
drm/tegra: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/tegra/tegra-drm.ko:
-.rodata 13672
+.rodata 13684
-.data 1108
+.data 1096
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-26-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:21:12 +0000 (12:21 +0100)]
drm/rockchip: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/rockchip/dw_hdmi-rockchip.ko:
-.rodata 772
+.rodata 828
-.data 148
+.data 92
drivers/gpu/drm/rockchip/rockchipdrm.ko:
-.rodata 748
+.rodata 760
-.data 448
+.data 436
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-25-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:21:11 +0000 (12:21 +0100)]
drm/nouveau: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/nouveau/nouveau.ko:
-.rodata 105688
+.rodata 105792
-.data 125724
+.data 125620
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-24-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:21:10 +0000 (12:21 +0100)]
drm/mgag200: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/mgag200/mgag200.ko:
-.text 29244
+.text 29232
-.rodata 600
+.rodata 668
-.data 688
+.data 620
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-23-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:21:09 +0000 (12:21 +0100)]
drm/imx: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/imx/imxdrm.ko:
-.rodata 624
+.rodata 652
-.data 372
+.data 344
drivers/gpu/drm/imx/imx-ipuv3-crtc.ko:
-.rodata 224
+.rodata 280
-.data 184
+.data 128
drivers/gpu/drm/imx/imx-ldb.ko:
-.rodata 660
+.rodata 784
-.data 240
+.data 116
drivers/gpu/drm/imx/imx-tve.ko:
-.rodata 400
+.rodata 524
-.data 416
+.data 292
drivers/gpu/drm/imx/parallel-display.ko:
-.rodata 400
+.rodata 524
-.data 216
+.data 92
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-22-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:21:08 +0000 (12:21 +0100)]
drm/i2c/sil164: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/i2c/sil164.ko:
-.text 1660
+.text 1656
-.rodata 56
+.rodata 104
-.data 212
+.data 164
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-21-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:21:07 +0000 (12:21 +0100)]
drm/i2c/adv7511: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/i2c/adv7511.ko:
-.rodata 1368
+.rodata 1416
-.data 164
+.data 116
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-20-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:21:06 +0000 (12:21 +0100)]
drm/exynos: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/exynos/exynosdrm.ko:
-.text 125792
+.text 125788
-.rodata 10972
+.rodata 11748
-.data 6720
+.data 5944
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-19-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:21:05 +0000 (12:21 +0100)]
drm/cirrus: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/cirrus/cirrus.ko:
-.text 10104
+.text 10092
-.rodata 528
+.rodata 596
-.data 608
+.data 540
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-18-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:21:04 +0000 (12:21 +0100)]
drm/i2c/ch7006: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/i2c/ch7006.ko:
-.text 5752
+.text 5760
-.rodata 6608
+.rodata 6656
-.data 216
+.data 168
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-17-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:21:03 +0000 (12:21 +0100)]
drm/bridge/nxp-ptn3460: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/bridge/nxp-ptn3460.ko:
-.rodata 440
+.rodata 536
-.data 208
+.data 112
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-16-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:21:02 +0000 (12:21 +0100)]
drm/bridge/dw_hdmi: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/bridge/dw_hdmi.ko:
-.rodata 120
+.rodata 216
-.data 96
+.data 0
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-15-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:21:01 +0000 (12:21 +0100)]
drm/bochs: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/bochs/bochs-drm.ko:
-.text 7608
+.text 7600
-.rodata 648
+.rodata 716
-.data 612
+.data 544
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-14-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:21:00 +0000 (12:21 +0100)]
drm/atmel-hlcdc: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/atmel-hlcdc/atmel-hlcdc-dc.ko:
-.text 12488
+.text 12480
-.rodata 1696
+.rodata 1760
-.data 776
+.data 712
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-13-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:20:59 +0000 (12:20 +0100)]
drm/armada: Constify function pointer structs
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/armada/armada.ko:
-.rodata 1040
+.rodata 1100
-.data 1156
+.data 1096
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-12-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Dec 2015 11:20:58 +0000 (12:20 +0100)]
drm: Constify drm_encoder_slave_funcs
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-11-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Luis de Bethencourt [Tue, 15 Dec 2015 11:21:16 +0000 (12:21 +0100)]
drm: atmel-hlcdc: Fix module autoload for OF platform driver
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-29-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Nicolas Ferre [Tue, 15 Dec 2015 11:20:57 +0000 (12:20 +0100)]
drm: atmel-hlcdc: add support for sama5d2 SoCs
As the hardware description for this chip is the same as the sama5d4, we use
this SoC structures for layers and DC descriptions. Thus only 2 lines are added
to the atmel_hlcdc_of_match table.
The compatible string is already documented in the parent MFD driver's binding.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-10-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Frediano Ziglio [Tue, 15 Dec 2015 11:20:56 +0000 (12:20 +0100)]
drm/qxl: use to_qxl_bo macro
Instead of using container_of directly use to_qxl_bo macro.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-9-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rasmus Villemoes [Tue, 15 Dec 2015 11:20:55 +0000 (12:20 +0100)]
drm/vmwgfx: check kmalloc return value
srf->sizes has been allocated and checked a few lines above; fix up
the copy-pasto so that we check srf->offsets.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-8-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rasmus Villemoes [Tue, 15 Dec 2015 11:20:54 +0000 (12:20 +0100)]
drm/vmwgfx: use kzalloc in vmw_surface_define_ioctl()
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-7-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rasmus Villemoes [Tue, 15 Dec 2015 11:20:53 +0000 (12:20 +0100)]
drm/omap: use kzalloc in sita_init()
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-6-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Thierry Reding [Tue, 15 Dec 2015 11:20:52 +0000 (12:20 +0100)]
drm/imx: Drop pipe field from struct imx_drm_crtc
Use the drm_crtc_index() helper to determine the pipe number of the CRTC
instead.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-5-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Thierry Reding [Tue, 15 Dec 2015 11:20:51 +0000 (12:20 +0100)]
drm/imx: Make pipe number unsigned
There's no reason whatsoever why this should ever be negative. The same
goes for the number of pipes added to the DRM device.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-4-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Thierry Reding [Tue, 15 Dec 2015 11:20:50 +0000 (12:20 +0100)]
drm/bochs: Store correct CRTC index in events
Previously a negative pipe caused a special case to be triggered for
drivers that didn't have proper VBLANK support. The trigger for this
special case is now independent of the pipe, so the correct CRTC index
can now be stored in events.
v2: convert to use drm_crtc_send_vblank_event()
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-3-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Thierry Reding [Tue, 15 Dec 2015 11:20:49 +0000 (12:20 +0100)]
drm/gma500: Sanity-check pipe index
If the DSI output isn't connected, then mdfld_dsi_encoder_get_pipe()
will return -1. The mdfld_dsi_dp_mode_set() function doesn't properly
check for this condition and causes the following compiler warnings:
CC drivers/gpu/drm/gma500/mdfld_dsi_dpi.o
drivers/gpu/drm/gma500/mdfld_dsi_dpi.c: In function ‘mdfld_dsi_dpi_mode_set’:
drivers/gpu/drm/gma500/mdfld_dsi_dpi.c:828:35: warning: array subscript is below array bounds [-Warray-bounds]
u32 pipeconf = dev_priv->pipeconf[pipe];
^
drivers/gpu/drm/gma500/mdfld_dsi_dpi.c:829:33: warning: array subscript is below array bounds [-Warray-bounds]
u32 dspcntr = dev_priv->dspcntr[pipe];
^
Fix this by checking for a valid pipe before indexing the pipeconf and
dspcntr arrays.
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-2-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eric Anholt [Tue, 15 Dec 2015 00:26:26 +0000 (16:26 -0800)]
drm: Use the driver's gem_object_free function from CMA helpers.
VC4 wraps the CMA objects in its own structures, so it needs to do its
own teardown (waiting for GPU to finish, updating bo_stats tracking).
The other CMA drivers are using drm_gem_cma_free_object as their
gem_free_object, so this should be a no-op for them.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Harry Wentland [Mon, 7 Dec 2015 18:55:52 +0000 (13:55 -0500)]
drm/dp/mst: save vcpi with payloads
This makes it possibly for drivers to find the associated
mst_port by looking at the payload allocation table.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449514552-10236-3-git-send-email-harry.wentland@amd.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mykola Lysenko [Mon, 7 Dec 2015 18:55:51 +0000 (13:55 -0500)]
drm/dp/mst: reply with ACK for UP reqs
Currently we reply with NACK to UP requests which might
confuse receivers. We haven't seen any actual issues with
this but should still respond to UP requests correctly.
Signed-off-by: Mykola Lysenko <Mykola.Lysenko@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449514552-10236-2-git-send-email-harry.wentland@amd.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Tue, 8 Dec 2015 08:49:19 +0000 (09:49 +0100)]
drm: Move more framebuffer doc from docbook to kerneldoc
I missed a few paragraphs in the docbook that need to be pulled into
the fbdev vfunc docs.
v2: Spelling fixes from Thierry.
Cc: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449564561-3896-3-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Daniel Vetter [Tue, 8 Dec 2015 08:49:18 +0000 (09:49 +0100)]
drm/atomic-helper: Drop unneeded argument from check_pending_encoder
Just a remnant from an old iteration of this patch that I've forgotten
to remove: We only need the encoder to figure out whether it has been
reassigned in this update already or not to figure out whether there's
a conflict or not.
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449564561-3896-2-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Danilo Cesar Lemes de Paula [Wed, 25 Nov 2015 17:07:55 +0000 (18:07 +0100)]
drm/doc: Convert to markdown
DRM Docbook is now Markdown ready. This means its doc is able to
use markdown text on it.
* Documentation/DocBook/drm.tmpl: Contains a table duplicated from
drivers/gpu/drm/i915/i915_reg.h. This is not needed anymore
* drivers/gpu/drm/drm_modeset_lock.c: had a code example that used
to look pretty bad on html. Fixed by using proper code markup.
* drivers/gpu/drm/drm_prime.c: Remove spaces between lines to make
a proper markup list.
* drivers/gpu/drm/i915/i915_reg.h: Altought pandoc supports tables,
it doesn't support table cell spanning. But we can use fixed-width
for those special cases.
* include/drm/drm_vma_manager.h: Another code example that should be
proper indented with four spaces.
v2 (Daniel): Adjust name to gpu.xml due to rename.
v3 (Daniel):
Split out the actual enabling in the Makefile - this way we can merge
the conversion, while just keeping the enabling in a drm-private tree.
Signed-off-by: Danilo Cesar Lemes de Paula <danilo.cesar@collabora.co.uk> (v1)
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephan Mueller <smueller@chronox.de>
Cc: Michal Marek <mmarek@suse.cz>
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: intel-gfx <intel-gfx@lists.freedesktop.org>
Cc: dri-devel <dri-devel@lists.freedesktop.org>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448471279-19748-2-git-send-email-daniel.vetter@ffwll.ch
Dave Airlie [Tue, 15 Dec 2015 01:01:04 +0000 (11:01 +1000)]
Merge tag 'drm-intel-next-2015-12-04-1' of git://anongit.freedesktop.org/drm-intel into drm-next
This is the "fix igt basic test set issues" edition.
- more PSR fixes from Rodrigo, getting closer
- tons of fifo underrun fixes from Ville
- runtime pm fixes from Imre, Daniel Stone
- fix SDE interrupt handling properly (Jani Nikula)
- hsw/bdw fdi modeset sequence fixes (Ville)
- "don't register bad VGA connectors and fall over" fixes (Ville)
- more fbc fixes from Paulo
- and a grand total of exactly one feature item: Implement dma-buf/fence based
cross-driver sync in the i915 pageflip path (Alex Goins)
* tag 'drm-intel-next-2015-12-04-1' of git://anongit.freedesktop.org/drm-intel: (70 commits)
drm/i915: Update DRIVER_DATE to
20151204
drm/i915/skl: Add SKL GT4 PCI IDs
Revert "drm/i915: Extend LRC pinning to cover GPU context writeback"
drm/i915: Correct the Ref clock value for BXT
drm/i915: Restore skl_gt3 device info
drm/i915: Fix RPS pointer passed from wait_ioctl to i915_wait_request
Revert "drm/i915: Remove superfluous NULL check"
drm/i915: Clean up device info structure definitions
drm/i915: Remove superfluous NULL check
drm/i915: Handle cdclk limits on broadwell.
i915: wait for fence in prepare_plane_fb
i915: wait for fence in mmio_flip_work_func
drm/i915: Extend LRC pinning to cover GPU context writeback
drm/i915/guc: Clean up locks in GuC
drm/i915: only recompress FBC after flushing a drawing operation
drm/i915: get rid of FBC {,de}activation messages
drm/i915: kill fbc.uncompressed_size
drm/i915: use a single intel_fbc_work struct
drm/i915: check for FBC planes in the same place as the pipes
drm/i915: alloc/free the FBC CFB during enable/disable
...
Nicolai Hähnle [Sat, 12 Dec 2015 16:42:23 +0000 (11:42 -0500)]
drm/ttm: fix documentation of ttm_bo_reserve
Previously, the comment was inconsistent. EDEADLK is what the ww_mutex
mechanism really returns.
Signed-off-by: Nicolai Hähnle <Nicolai.Haehnle@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Tue, 15 Dec 2015 00:43:27 +0000 (10:43 +1000)]
Merge tag 'drm-vc4-next-2015-12-11' of github.com/anholt/linux into drm-next
This pull request brings in 3D acceleration support for the VC4 GPU.
While there is still performance work to be done (particularly
surrounding RCL generation), the CL submit ABI should be settled and
done now.
* tag 'drm-vc4-next-2015-12-11' of http://github.com/anholt/linux:
drm/vc4: Add an interface for capturing the GPU state after a hang.
drm/vc4: Add support for async pageflips.
drm/vc4: Add support for drawing 3D frames.
drm/vc4: Bind and initialize the V3D engine.
drm/vc4: Fix a typo in a V3D debug register.
drm/vc4: Add an API for creating GPU shaders in GEM BOs.
drm/vc4: Add create and map BO ioctls.
drm/vc4: Add a BO cache.
drm: Create a driver hook for allocating GEM object structs.
Dave Airlie [Tue, 15 Dec 2015 00:42:07 +0000 (10:42 +1000)]
Merge branch 'exynos-drm-next' of git://git./linux/kernel/git/daeinki/drm-exynos into drm-next
- Support runtime pm
. In case of most ARM SoC, each IP has each power domain which should be
controlled by each IP driver using runtime pm interface. So this patch
series makes each IP driver to control its own power domain when
drm dpms is requested.
- Support of_graph based dt binding for DP panel.
. This patch series adds of_graph based dt binding for DP panel.
And also it keeps backward compatibility. This includes dt binding
patch so I got Acked-by from Krzysztof Kozlowski who is a Exynos
SoC maintainer and from Rob Herring who is a device tree maintainer.
- Cleanup for Exynos DRM IPP enhancement.
. This patch series is a first step for enhancing existing IPP framework
which will integrate existing IPP functions with DRM KMS part so that
these can be transparent to userspace. For other portion of the patch
series, we will have more times for the review.]
* 'exynos-drm-next' of git://git.kernel.org:/pub/scm/linux/kernel/git/daeinki/drm-exynos: (29 commits)
drm/exynos: gem: remove old unused prototypes
drm/exynos: fimd: fix dma burst size setting for small plane size
drm/exynos: fix clipping when scaling is enabled
drm/exynos: mixer: use ratio precalculated in exynos_state
drm/exynos: add generic check for plane state
drm/exynos: introduce exynos_drm_plane_config structure
drm/exynos: mixer: enable video overlay plane only when VP is available
drm/exynos: mixer: use crtc->state->adjusted_mode instead of crtc->mode
drm/exynos: introduce exynos_drm_plane_state structure
drm/exynos: move dma_addr attribute from exynos plane to exynos fb
drm/exynos: exynos7-decon: remove excessive check
drm/exynos: rotator: convert to common clock framework
drm/exynos: gsc: add device tree support and remove usage of static mappings
drm/exynos: gsc: fix wrong pm_runtime state
drm/exynos: gsc: prepare and unprepare gsc clock
ARM: dts: Use OF graph for DP to panel connection in exynos5800-peach-pi
dt-bindings: exynos-dp: update ports node binding for panel
drm/exynos: dp: add of_graph dt binding support for panel
drm/exynos: decon: remove unused variables
drm/exynos: dsi: modify a error type when getting a node failed
...
Dave Airlie [Tue, 15 Dec 2015 00:07:07 +0000 (10:07 +1000)]
Merge tag 'topic/drm-misc-2015-12-14' of git://anongit.freedesktop.org/drm-intel into drm-next
Last (very likely at least) drm-misc pull for 4.5. 3 big things:
- piles of docs for kms vtables.
- drm.debug dmesg output prettification from Ville (i915 parts are for 4.6
I think)
- connector mode probing/validating/merging cleanup from Ville.
[airlied : fix drm_encoder_init conflict.]
* tag 'topic/drm-misc-2015-12-14' of git://anongit.freedesktop.org/drm-intel: (43 commits)
drm: modes: Revert
cc344980c767 "replace simple_strtoul by kstrtouint"
drm: Expand the drm_helper_probe_single_connector_modes() docs
drm: Allow override_edid to override the firmware EDID
drm/sti: Drop bogus drm_mode_sort() call
drm: Drop drm_helper_probe_single_connector_modes_nomerge()
drm: Only merge mode type bits between new probed modes
drm: Flatten drm_mode_connector_list_update() a bit
drm: Rename MODE_UNVERIFIED to MODE_STALE
drm: Don't overwrite UNVERFIED mode status to OK
drm: Add plane->name and use it in debug prints
drm: Add crtc->name and use it in debug messages
drm: Use driver specified encoder name
drm: Pass 'name' to drm_encoder_init()
drm: Pass 'name' to drm_universal_plane_init()
drm: Pass 'name' to drm_crtc_init_with_planes()
drm: Documentation style guide
drm: Document drm_encoder/crtc_helper_funcs
drm: Move drm_display_mode an related docs into kerneldoc
drm/atomic-helper: Mention the new system/resume helpers the docs
drm: Document drm_connector_helper_funcs
...
Dave Airlie [Mon, 14 Dec 2015 23:52:29 +0000 (09:52 +1000)]
Merge branch 'msm-next' of git://people.freedesktop.org/~robclark/linux into drm-next
Main thing this time around is DSI support for msm8960/apq8064, which
should be helpful for getting an upstream kernel working on
nexus7/nexus4/etc.
* 'msm-next' of git://people.freedesktop.org/~robclark/linux: (29 commits)
drm/msm/mdp: fix a problematic usage of WARN_ON()
drm/msm/dsi: Added missing mutex_unlock
drm/msm: ratelimit error irq msgs
drm/msm: Use unlocked gem unreferencing
drm/msm: trivial whitespace fix
dt-bindings: msm/dsi: Add DSIv2 documentation
dt-bindings: msm/dsi: Fix the order in which clocks are listed
drm/msm/dsi: Enable MMSS SPFB port via syscon
drm/msm/dsi: Don't use iommu for command TX buffer for DSIv2
drm/msm/dsi: Add dsi_cfg for APQ8064
drm/msm/dsi: Set up link clocks for DSIv2
drm/msm/dsi: Parse bus clocks from a list
drm/msm/dsi: Delay dsi_clk_init
drm/msm/dsi: Use a better way to figure out DSI version
drm/msm/dsi: Add DSI PLL for 28nm 8960 PHY
drm/msm/dsi: Add support for 28nm PHY on 8960
drm/msm/dsi: Don't get byte/pixel source clocks from DT
drm/msm/mdp4: Initialize DSI encoders
drm/msm/mdp4: Call custom round_pixclk helper only if the encoder type is TMDS
drm/msm/dsi: Add a mdp4 encoder for DSI
...
Geliang Tang [Wed, 25 Nov 2015 13:12:14 +0000 (21:12 +0800)]
drm/msm/mdp: fix a problematic usage of WARN_ON()
WARN_ON() takes a condition rather than a format string. This patch
converted WARN_ON() to WARN() instead.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
saurabh [Sun, 6 Dec 2015 19:49:21 +0000 (01:19 +0530)]
drm/msm/dsi: Added missing mutex_unlock
in case of failed to get iova, function was returning without releasing
the mutex. Added it.
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Rob Clark [Wed, 2 Dec 2015 19:40:44 +0000 (14:40 -0500)]
drm/msm: ratelimit error irq msgs
When things go bad and don't recover, we can be getting an err irq every
vblank.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Daniel Vetter [Mon, 23 Nov 2015 09:32:41 +0000 (10:32 +0100)]
drm/msm: Use unlocked gem unreferencing
For drm_gem_object_unreference callers are required to hold
dev->struct_mutex, which these paths don't. Enforcing this requirement
has become a bit more strict with
commit
ef4c6270bf2867e2f8032e9614d1a8cfc6c71663
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 15 09:36:25 2015 +0200
drm/gem: Check locking in drm_gem_object_unreference
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Rob Clark [Mon, 14 Dec 2015 14:59:56 +0000 (09:59 -0500)]
drm/msm: trivial whitespace fix
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Tue, 1 Dec 2015 06:18:15 +0000 (11:48 +0530)]
dt-bindings: msm/dsi: Add DSIv2 documentation
Add additional property info needed for DSIv2 DT.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Tue, 1 Dec 2015 06:09:59 +0000 (11:39 +0530)]
dt-bindings: msm/dsi: Fix the order in which clocks are listed
List the clocks in the order that's used in DT. We don't have mdp/dsi
DT nodes for any SoC in upstream yet, but we align with the order
we intend to use.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 14 Oct 2015 10:01:13 +0000 (15:31 +0530)]
drm/msm/dsi: Enable MMSS SPFB port via syscon
For DSIv2 to work, we need to enable MMSS_AHB_ARB_MASTER_PORT in
MMSS_SFPB. We enable the required bitfield by retrieving MMSS_SFPB
regmap pointer via syscon.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Tue, 13 Oct 2015 06:50:47 +0000 (12:20 +0530)]
drm/msm/dsi: Don't use iommu for command TX buffer for DSIv2
We currently use iommu allocated DMA buffers for sending DSI commands.
DSIv2 doesn't have a port connected to the MDP iommu. Therefore, it
can't use iommu allocated buffers to fetch DSI commands.
Use a regular contiguous DMA buffer if we are DSIv2.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Mon, 12 Oct 2015 05:46:48 +0000 (11:16 +0530)]
drm/msm/dsi: Add dsi_cfg for APQ8064
Add a dsi_cfg entry for APQ8064. Since this is the first DSIv2 chip to
be supported, add a list of bus clocks that are required by the DSIv2
block.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Fri, 9 Oct 2015 11:02:38 +0000 (16:32 +0530)]
drm/msm/dsi: Set up link clocks for DSIv2
DSIv2 (DSI on older A family chips) has slightly different link clock
requirements.
First, we have an extra clock called src_clk (with a dedicated RCG).
This is required by the DSI controller to process the pixel data
coming from MDP. It needs to be set at the rate "pclk * bytes_per_pixel".
We also need to explicitly configure esc_clk. On DSI6G chips, we don't
need to set a rate to esc_clk because its RCG is always sourced from
crystal clock (19.2 Mhz in all cases), which is within the escape clock
frequency range in the mipi DSI spec. For chips with DSIv2, the crystal
clock rate may not be within the required range (27Mhz on APQ8064).
Therefore, we derive it from the DSI byte clock. We calculate an esc_clck
rate that is within the mipi spec and also divisible by the byte clock
rate.
When setting rate and enabling the link clocks, we make sure that byte_clk
is configured before esc_clk, and src_clk before pixel_clk. We create two
different link_enable funcs for DSI6G and DSIv2 since the sequences are
different.
We also obtain two extra source clocks (dsi_src_clk and esc_src_clk) and
set their parent to the clocks provided by DSI PLL.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Fri, 9 Oct 2015 09:51:12 +0000 (15:21 +0530)]
drm/msm/dsi: Parse bus clocks from a list
DSI bus clocks seem to vary between different DSI host versions, and the
SOC to which they belong. Even the enable/disable sequence varies.
Provide a list of bus clock names in dsi_cfg. The driver will use this to
retrieve the clocks, and enable/disable them.
Add bus clock lists for DSI6G, and DSI for MSM8916(this is DSI6G too, but
there is no MMSS_CC specific clock since there is no MMSS clock controller
on 8916).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Fri, 9 Oct 2015 07:10:39 +0000 (12:40 +0530)]
drm/msm/dsi: Delay dsi_clk_init
Initialize clocks only after we get the DSI host version. This will allow
us to get clocks using a pre-defined list based on the DSI major/minor
version of the host. This is required since clock requirements of
different major DSI revisions(v2 vs 6g) aren't the same.
Modify dsi_get_version to get the interface clock, and then put it after
it is used.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Fri, 9 Oct 2015 05:40:59 +0000 (11:10 +0530)]
drm/msm/dsi: Use a better way to figure out DSI version
The current version checking mechanism works fine for DSI6G blocks. It
doesn't work so well for older generation DSIv2 blocks.
The initial read of REG_DSI_6G_HW_VERSION(offset 0x0) would result in a
read of REG_DSI_CTRL for DSIv2. This register won't necessarily be 0 on
DSIv2. It can be non zero if DSI was previously initialized by the
bootloader.
Instead of reading offset 0x0, we now read offset 0x1f0. For DSIv2, this
register is DSI_VERSION, and is bound to be non-zero. On DSI6G, this
register(offset 0x1f0) is SCRATCH_REGISTER_0, which no one ever seems to
touch, and from all register dumps I'vc seen, holds 0 all the time.
Modify dsi_get_version to read REG_DSI_VERSION to determine whether we
are DSI6G or DSIv2.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 14 Oct 2015 06:33:44 +0000 (12:03 +0530)]
drm/msm/dsi: Add DSI PLL for 28nm 8960 PHY
Add DSI PLL common clock framework clocks for 8960 PHY.
The PLL here is different from the ones found in B family msm chips. As
before, the DSI provides two clocks to the outside world. dsixpll and
dsixpllbyte (x = 1, 2). dsixpll is a regular clock divider, but
dsixpllbyte is modelled as a custom clock divider.
dsixpllbyte is the starting point of the PLL configuration. It is the
one that sets up the VCO clock rate. We need the VCO clock rate in the
form: F * byteclk, where F is a multiplication factor that varies on
the byte clock the DSI driver is trying to set. We use the custom
clk_ops for dsixpllbyte to ensure that the parent (VCO) is set at this
rate.
An additional divider (POSTDIV1) generates the bitclk. Since bit clock
can be derived from byteclock, we calculate it internally, and don't
expose it as a clock.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 14 Oct 2015 06:30:34 +0000 (12:00 +0530)]
drm/msm/dsi: Add support for 28nm PHY on 8960
DSI PHY on MSM8960 and APQ8064 is a 28nm PHY that's different from the
supported 28nm LP PHY found in newer chips.
Add support for the new PHY.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Mon, 30 Nov 2015 12:17:17 +0000 (17:47 +0530)]
drm/msm/dsi: Don't get byte/pixel source clocks from DT
We retrieve the byte and pixel source clocks (RCG clocks) in the dsi
driver via DT. These are needed so that we can re-parent these source
clocks if we want to drive it using a different DSI PLL.
We shouldn't get these via DT because they aren't clocks that directly
serve as inputs to the dsi host.
Fortunately, there is a static parent-child link between the
byte_clk_src/pixel_clk_src and byte_clk/pixel_clk clocks. So, we can
retrieve the source clocks via clk_get_parent.
Do this instead of retrieving via DT.
Cc: Rob Herring <robh@kernel.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 18 Nov 2015 12:28:28 +0000 (17:58 +0530)]
drm/msm/mdp4: Initialize DSI encoders
Create DSI encoders during modeset_init. The 2 encoders should ideally be
one command mode and one video mode DSI encoder respectively, but we don't
support command mode yet. We just create 2 of the same because the dsi
driver expects it, we end up using only the first one.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 18 Nov 2015 12:27:16 +0000 (17:57 +0530)]
drm/msm/mdp4: Call custom round_pixclk helper only if the encoder type is TMDS
The mdp_kms round_pixclk op creates problems when we have more
interfaces in use. It calls the DTV encoder's helper by default.
Check on encoder type and call the corresponding encoder's
func meant for rounding pixel clock. DSI and LVDS don't require
rounding, so just return rate in their case.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Vinay Simha BN [Mon, 19 Oct 2015 06:57:11 +0000 (12:27 +0530)]
drm/msm/dsi: Add a mdp4 encoder for DSI
Create an mdp4 incoder for DSI. Only DSI video mode is supported as of
now.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vinay Simha BN <vinaysimha@inforcecomputing.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 18 Nov 2015 11:45:50 +0000 (17:15 +0530)]
drm/msm/mdp4: Initialize LCDC encoder even if panel driver isn't available
Currently, the driver defers if it doesn't find a drm_panel. This forces
us to have a drm_panel, if not, the driver isn't usable.
Make the lcdc encoder initialization independent of the availability of
the drm panel. We only check if there is a panel node specified in DT. If
it isn't, then we don't initialize the encoder at all. The panel node is
passed to the lcdc encoder and lvds connector drivers.
The connector driver takes the responsibility to retrieve the drm_panel
from the panel node, and update the status on whether the panel is
connected or not. This makes the panel usable even if the drm_panel
driver is inserted as a module later on.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Mon, 19 Oct 2015 06:50:52 +0000 (12:20 +0530)]
drm/msm/mdp4: Clean up modeset_init
modeset_init() for mdp4 isn't very flexible. That makes it hard to add
more interfaces.
Split out the encoder/connector creation code in modeset_init into a
separate function. This is similar to what's done in modeset_init for
mdp5.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 18 Nov 2015 11:02:28 +0000 (16:32 +0530)]
drm/msm/adreno: Remove CONFIG_OF checks
Remove CONFIG_OF checks in adreno_device.c. The downstream bus scaling
stuff is included only when CONFIG_OF is not set. So, remove that too.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Fri, 30 Oct 2015 07:05:55 +0000 (12:35 +0530)]
drm/msm/hdmi: remove CONFIG_OF checks
We now only care about kernels that support DT. Remote the non-DT stuff.
While we're at it, use of_device_get_match_data to retrieve match data.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 18 Nov 2015 07:14:52 +0000 (12:44 +0530)]
drm/msm/mdp: Remove CONFIG_OF checks from MDP drivers
We don't intend to use downstream non-DT kernels anymore, so remove
CONFIG_OF checks.
Update the TODO comment so that we don't forget about max_clk setting
for non APQ8064 chips having MDP4.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 18 Nov 2015 07:06:19 +0000 (12:36 +0530)]
dt-bindings: drm/msm: Update MDP bindings
Update DT bindings for mdp. We now have a more uniform and future-proof
set of compatible strings.
MDP5 bindings were missing. Add those and update details on the
clock-names properties.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 18 Nov 2015 06:58:39 +0000 (12:28 +0530)]
drm/msm: Update compatible strings for mdp
Create distinct compatible strings for mdp4 and mdp5. Keep "qcom,mdss_mdp"
as is to support downstream kernels.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 18 Nov 2015 06:45:14 +0000 (12:15 +0530)]
drm/msm: Remove non-DT code in msm_drv
Support for non-DT kernels was mainly to use v3.4 downstream kernels.
This is no longer a priority now as we have reasonable support upstream.
Remove CONFIG_OF from the top level msm_drv.c file. While we're at it,
clean up the data matching process using of_device_get_match_data.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Mon, 26 Oct 2015 09:13:57 +0000 (14:43 +0530)]
drm/msm/mdp5: high precision vblank timestamp support
MDP5 has line count and frame count registers for each interface. Enable
these counters and use them to implement the get_vblank_timestamp drm
driver op.
The line counter starts with the value 1 at the beginning of the VSYNC
pulse and ends with value VTOTAL at the end of VFP. This value is used
to determine whether we're in blanking period or not, and an adjusted
value of this counter is used to get vpos as expected by
get_scanout_position. Since there is no way to calculate hpos, we always
set it to 0.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Marek Szyprowski [Mon, 30 Nov 2015 13:53:30 +0000 (14:53 +0100)]
drm/exynos: gem: remove old unused prototypes
This patch removes old, unused function prototypes from exynos_drm_gem.h.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Marek Szyprowski [Mon, 30 Nov 2015 13:53:29 +0000 (14:53 +0100)]
drm/exynos: fimd: fix dma burst size setting for small plane size
This patch fixes trashed display of buffers cropped to very small width.
Even if DMA is unstable and causes tearing when changing the burst size,
it is still better than displaying a garbage.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Marek Szyprowski [Mon, 30 Nov 2015 13:53:28 +0000 (14:53 +0100)]
drm/exynos: fix clipping when scaling is enabled
This patch fixes calculation of src x/y offset for negative crtc x/y
values when scaling is enabled. This fixes possible IOMMU fault when
scaling is enabled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Marek Szyprowski [Mon, 30 Nov 2015 13:53:27 +0000 (14:53 +0100)]
drm/exynos: mixer: use ratio precalculated in exynos_state
Common plane code already calculates and checks for supported scalling
modes, so additional code in mixer driver can be now removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Marek Szyprowski [Mon, 30 Nov 2015 13:53:26 +0000 (14:53 +0100)]
drm/exynos: add generic check for plane state
This patch adds generic check for plane state - display area dimensions,
so drivers can always assume that they get valid plane state to set.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Marek Szyprowski [Mon, 30 Nov 2015 13:53:25 +0000 (14:53 +0100)]
drm/exynos: introduce exynos_drm_plane_config structure
This patch adds common structure for keeping plane configuration and
capabilities data. This patch is inspired by similar code developed by
Tobias Jakobi.
Changelog v2:
- fix vidi_win_types(i) call. vidi_win_types is not a function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Marek Szyprowski [Mon, 30 Nov 2015 13:53:24 +0000 (14:53 +0100)]
drm/exynos: mixer: enable video overlay plane only when VP is available
Video overlay plane should be registered only when suitable hardware
sub-block (Video Processor) is available.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Marek Szyprowski [Mon, 30 Nov 2015 13:53:23 +0000 (14:53 +0100)]
drm/exynos: mixer: use crtc->state->adjusted_mode instead of crtc->mode
This patch replaces usage of crtc->mode with crtc->state->adjusted_mode
like it is already done in common plane code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Marek Szyprowski [Mon, 30 Nov 2015 13:53:22 +0000 (14:53 +0100)]
drm/exynos: introduce exynos_drm_plane_state structure
This patch introduces exynos_drm_plane_state structure, which subclasses
drm_plane_state and holds precalculated data suitable for configuring
Exynos hardware.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>