OSDN Git Service
Wolfram Sang [Tue, 9 Jun 2015 07:14:39 +0000 (16:14 +0900)]
i2c: sh_mobile: add errata workaround
This used to be in platform init code. We want it to do in the driver
now. This is basically a code move and a new compatible added.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cyrille Pitchen [Thu, 11 Jun 2015 09:16:32 +0000 (11:16 +0200)]
i2c: at91: fix code checker warnings
buf_len is a size_t, so unsigned, but was tested with '<= 0'.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Feng Kan [Tue, 2 Jun 2015 23:43:09 +0000 (16:43 -0700)]
i2c: busses: xgene-slimpro: fix incorrect __init declation for probe
Fix section mismatch error during kernel build for xgene_slimpro_i2c_probe
function. It was incorrectly defined with __init declaration.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Alexander Sverdlin [Tue, 9 Jun 2015 11:10:10 +0000 (13:10 +0200)]
i2c: davinci: Avoid sending to own address
Sending a message to own address locks the controller up in very bizarre state,
it behaves as slave even if MDR register clearly states master. The controller
remains in this state until reset. To avoid unnecessary timeouts simply avoid
sending to own address. The controller cannot do this any way. Also, do not
enable AAS IRQ, as the slave mode is not supported by the driver and the only
possibility to trigger this IRQ is to send to own address.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Alexander Sverdlin [Tue, 9 Jun 2015 10:58:29 +0000 (12:58 +0200)]
i2c: davinci: Refactor i2c_davinci_wait_bus_not_busy()
There are several problems in the function:
- "to_cnt" variable does nothing
- schedule_timeout() call without setting current state does nothing
- "allow_sleep" parameter is not really used
Refactor the function so that it really tries to wait. In case of timeout try
to recover the bus.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Kamal Dasu [Tue, 9 Jun 2015 19:36:20 +0000 (15:36 -0400)]
i2c: brcmstb: Add Broadcom settop SoC i2c controller driver
Adding support for i2c controller driver for Broadcom settop
SoCs.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
[wsa: removed superfluous owner in platform_driver]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cyrille Pitchen [Tue, 9 Jun 2015 16:22:19 +0000 (18:22 +0200)]
i2c: at91: add support to FIFOs
When FIFOs are available and enabled, the driver now configures the Atmel
eXtended DMA Controller to perform word accesses instead of byte accesses
when possible.
The actual access width depends on the size of the buffer to transmit.
To enable FIFO support the "atmel,fifo-size" property must be set properly
in the I2C controller node of the device tree.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cyrille Pitchen [Tue, 9 Jun 2015 16:22:18 +0000 (18:22 +0200)]
i2c: at91: print hardware version
The probe() function now prints the hardware version of the I2C
controller.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[wsa: s/version/hw version/] for clarity]
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cyrille Pitchen [Tue, 9 Jun 2015 16:22:17 +0000 (18:22 +0200)]
i2c: at91: add support for new alternative command mode
The alternative command mode was introduced to simplify the transmission
of STOP conditions and to solve timing and latency issues around them.
This mode relies on a new register, the Alternative Command Register,
which must be set at the same time as the Master Mode Register. This new
register was designed to allow simple setup of basic combined transactions
built from up to two unitary transactions.
Indeed, the ACR is split into two areas, which describe one unitary
transaction each. Each area is filled with Data Length 8bit counter, a
Direction and a PEC Request bit. The PEC bit is only used in SMBus mode
and is not supported by this driver yet. Also when using alternative
command mode, the MREAD bit from the Master Mode Register is ignored.
Instead the Direction bits from ACR are used to setup the direction, read
or write, of each unitary transaction. Finally the 8bit counters must
filled with the data length of their respective transaction. Then if only
one transaction is to be used, the data length of the second one must be
set to zero. At the moment, this driver uses only the first transaction.
In addition to MMR and ACR, the Control Register also need to be written
to enable the alternative command mode. That's the purpose of its ACMEN
bit, which stands for Alternative Command Mode Enable.
Note that the alternative command mode is compatible with the use of the
Internal Address Register. So combined transactions for eeprom read are
actually implemented with the Internal Address Register. This register is
written with up to 3 bytes, which are the internal address sent to the
slave through the first write transaction. Then the first area of the ACR
describe the write transaction to follow, which carries the data to be
read from the eeprom. The second area of the ACR is not used so its Data
Length 8bit counter is cleared.
For each byte sent or received by the device, the Data Length 8bit counter
is decremented. When it reaches 0, a STOP condition is automatically sent.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cyrille Pitchen [Tue, 9 Jun 2015 16:22:16 +0000 (18:22 +0200)]
i2c: at91: update documentation for DT bindings
add a new value "atmel,sama5d2-i2c" for the "compatible" property.
add a new optional property "atmel,fifo-size" to enable FIFO support when
available.
add missing optional properties "dmas" and "dma-names".
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cyrille Pitchen [Tue, 9 Jun 2015 16:22:15 +0000 (18:22 +0200)]
i2c: at91: use BIT() macro to define register bits
This patch just fixes typo before applying later patches which will use
register bits with index above 16.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cyrille Pitchen [Tue, 9 Jun 2015 16:22:14 +0000 (18:22 +0200)]
i2c: at91: fix a race condition when using the DMA controller
For TX transactions, the TXCOMP bit in the Status Register is cleared
when the first data is written into the Transmit Holding Register.
In the lines from at91_do_twi_transfer():
at91_twi_write_data_dma(dev);
at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP);
the TXCOMP interrupt may be enabled before the DMA controller has
actually started to write into the THR. In such a case, the TXCOMP bit
is still set into the Status Register so the interrupt is triggered
immediately. The driver understands that a transaction completion has
occurred but this transaction hasn't started yet. Hence the TXCOMP
interrupt is no longer enabled by at91_do_twi_transfer() but instead
by at91_twi_write_data_dma_callback().
Also, the TXCOMP bit in the Status Register in not a clear on read flag
but a snapshot of the transmission state at the time the Status
Register is read.
When a NACK error is dectected by the I2C controller, the TXCOMP, NACK
and TXRDY bits are set together to 1 in the SR. If enabled, the TXCOMP
interrupt is triggered at the same time. Also setting the TXRDY to 1
triggers the DMA controller to write the next data into the THR. Such
a write resets the TXCOMP bit to 0 in the SR. So depending on when the
interrupt handler reads the SR, it may fail to detect the NACK error
if it relies on the TXCOMP bit. The NACK bit and its interrupt should
be used instead.
For RX transactions, the TXCOMP bit in the Status Register is cleared
when the START bit is set into the Control Register. However to unify
the management of the TXCOMP bit when the DMA controller is used, the
TXCOMP interrupt is now enabled by the DMA callbacks for both TX and
RX transfers.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Cc: stable@vger.kernel.org #3.10 and later
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Ray Jui [Thu, 14 May 2015 22:36:04 +0000 (15:36 -0700)]
i2c: iproc: Add suspend/resume support
Add suspend/resume support to the Broadcom iProc I2C driver
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jisheng Zhang [Wed, 20 May 2015 14:33:13 +0000 (22:33 +0800)]
i2c: designware: Avoid unnecessary resuming during system suspend
Commit
1fc2fe204cb9 ("i2c: designware: Add runtime PM hooks") adds
runtime pm support using the same ops for system pm and runtime pm.
When suspend to ram, the i2c host may have been runtime suspended, thus
i2c_dw_disable() hangs.
Previously, I fixed this issue by separating ops for system pm and
runtime pm, then in the system suspend/resume path, runtime pm apis are
used to ensure the device is at correct state.
But as Mika Westerberg pointed out: it sounds a bit silly to resume the
device just because you want to call i2c_dw_disable() for it before
suspending again. He then suggested an elegant solution which keeps the
device runtime suspended during system suspend with the help of
'dev->power.direct_complete'. This patch adopted this solution, and in
fact Mika provided the main code.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Alexander Sverdlin [Wed, 13 May 2015 09:03:42 +0000 (11:03 +0200)]
i2c: axxia: Add bus recovery functionality
Use recovery framework and implement bus recovery using "Bus Monitor" register.
Tests show that shortening SDA to GND results in "completion" timeout with
"BUSY" bit still set, so initiate recovery in this case.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jarkko Nikula [Wed, 20 May 2015 13:36:52 +0000 (16:36 +0300)]
i2c: core: Reduce stack size of acpi_i2c_space_handler()
sizeof(struct i2c_client) is 1088 bytes on a CONFIG_X86_64=y build and
produces following warning when CONFIG_FRAME_WARN is set to 1024:
drivers/i2c/i2c-core.c: In function ‘acpi_i2c_space_handler’:
drivers/i2c/i2c-core.c:367:1: warning: the frame size of 1152 bytes is
larger than 1024 bytes [-Wframe-larger-than=]
This is not critical given that kernel stack is 16 kB on x86_64 but lets
reduce the stack usage by allocating the struct i2c_client from the heap.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Shailendra Verma [Tue, 19 May 2015 14:39:41 +0000 (20:09 +0530)]
i2c: smbus: fix typo in commet
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Shailendra Verma [Mon, 18 May 2015 17:07:54 +0000 (22:37 +0530)]
i2c: algo-pca: fix typo in comment
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Shailendra Verma [Mon, 18 May 2015 16:54:01 +0000 (22:24 +0530)]
i2c: core: fix typo in comment
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Eddie Huang [Thu, 21 May 2015 08:53:30 +0000 (16:53 +0800)]
I2C: mediatek: Add driver for MediaTek MT8173 I2C controller
Add mediatek MT8173 I2C controller driver. Compare to I2C controller
of earlier mediatek SoC, MT8173 fix write-then-read limitation, and
also increase message size to 64kb.
Signed-off-by: Xudong Chen <xudong.chen@mediatek.com>
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Xudong Chen [Thu, 21 May 2015 08:53:28 +0000 (16:53 +0800)]
I2C: mediatek: Add driver for MediaTek I2C controller
The mediatek SoCs have I2C controller that handle I2C transfer.
This patch include common I2C bus driver.
This driver is compatible with I2C controller on mt65xx/mt81xx.
Signed-off-by: Xudong Chen <xudong.chen@mediatek.com>
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Tue, 19 May 2015 16:29:48 +0000 (18:29 +0200)]
i2c: check for proper length of the reg property
int is vague, let's simply use the type of the variable in question.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Thu, 14 May 2015 12:40:05 +0000 (14:40 +0200)]
i2c: slave: add error messages to slave core
Inform users what went wrong from the core, so drivers don't have to do
it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Thu, 14 May 2015 12:40:04 +0000 (14:40 +0200)]
i2c: slave: docs: be more precise about the prerequsites
There was some confusion what was needed to utilize the slave support,
so let's be more precise about this. Add an introductory paragraph to
the development section while we are here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Thu, 14 May 2015 12:40:03 +0000 (14:40 +0200)]
i2c: rcar: report slave capabilities to users
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Thu, 14 May 2015 12:40:02 +0000 (14:40 +0200)]
i2c: add FUNC flag for slave capabilities
So users can check in advance if there is slave support.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Feng Kan [Fri, 24 Apr 2015 22:17:50 +0000 (15:17 -0700)]
i2c: add SLIMpro I2C device driver on APM X-Gene platform
Add SLIMpro I2C device driver on APM X-Gene platform. This I2C
device driver use the SLIMpro Mailbox driver to tunnel message to
the SLIMpro coprocessor to do the work of accessing I2C components.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Hieu Le <hnle@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Felipe Balbi [Wed, 6 May 2015 16:50:27 +0000 (11:50 -0500)]
i2c: omap: implement bus recovery
implement bus recovery methods for i2c-omap
so we can recover from situations where SCL/SDA
are stuck low.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Krzysztof Kozlowski [Fri, 1 May 2015 15:54:25 +0000 (00:54 +0900)]
i2c: constify platform_device_id
The platform_device_id is not modified by these drivers and core uses it
as const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pascal Huerst [Wed, 6 May 2015 13:07:04 +0000 (15:07 +0200)]
i2c: omap: Add calls for pinctrl state select
This adds calls to pinctrl subsystem in order to switch pin states
on suspend/resume if you provide a "sleep" state in DT.
If no "sleep" state is provided in the DT, these calls turn
to NOPs, so we don't need error checking here.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Geert Uytterhoeven [Tue, 5 May 2015 16:32:22 +0000 (18:32 +0200)]
i2c: Allow compile test of GPIO consumers if !GPIOLIB
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Shubhrajyoti Datta [Tue, 5 May 2015 12:36:05 +0000 (18:06 +0530)]
i2c: xiic: Fix kerneldoc warnings
info(drivers/i2c/busses/i2c-xiic.c:55): Scanning doc for struct xiic_i2c
Warning(drivers/i2c/busses/i2c-xiic.c:79): No description found for parameter 'endianness'
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Doug Anderson [Mon, 11 May 2015 19:44:28 +0000 (12:44 -0700)]
i2c: rk3x: Increase wait timeout to 1 second
Although unlikely, it is remotely possible for an i2c command to need
more than 200ms complete. Unlike smbus, i2c devices can clock stretch
for an unspecified amount of time. The longest time I've seen
specified for a device is 144ms (bq27541 battery gas), but one could
imagine a device taking a bit slower. 1 second "ought to be enough for
anyone."
The above is not the only justifcation for going above 200ms for a
timeout, though. It turns out that if you've got a large number of
printks going out to a serial console, interrupts on a CPU can be
disabled for hundreds of milliseconds. That's not a great situation to
be in to start with (maybe we should put a cap in vprintk_emit()) but
it's pretty annoying to start seeing unexplained i2c timeouts.
Note that to understand why we can timeout when printk has interrupts
disabled, you need to understand that on current Linux ARM kernels
interrupts are routed to a single CPU in a multicore system. Thus,
you can get:
1. CPU1 is running rk3x_i2c_xfer()
2. CPU0 calls vprintk_emit(), which disables all IRQs on CPU0.
3. I2C interrupt is ready but is set to only run on CPU0, where IRQs
are disabled.
4. CPU1 timeout expires. I2C interrupt is still ready, but CPU0 is
still sitting in the same vprintk_emit()
5. CPU1 sees that no interrupt happened in 200ms, so timeout.
A normal system shouldn't see i2c timeouts anyway, so increasing the
timeout should help people debugging without hurting other people
excessively.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Linus Torvalds [Mon, 4 May 2015 02:22:23 +0000 (19:22 -0700)]
Linux 4.1-rc2
Linus Torvalds [Mon, 4 May 2015 01:23:53 +0000 (18:23 -0700)]
Merge tag 'for_linus_stable' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Some miscellaneous bug fixes and some final on-disk and ABI changes
for ext4 encryption which provide better security and performance"
* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix growing of tiny filesystems
ext4: move check under lock scope to close a race.
ext4: fix data corruption caused by unwritten and delayed extents
ext4 crypto: remove duplicated encryption mode definitions
ext4 crypto: do not select from EXT4_FS_ENCRYPTION
ext4 crypto: add padding to filenames before encrypting
ext4 crypto: simplify and speed up filename encryption
Linus Torvalds [Mon, 4 May 2015 01:15:48 +0000 (18:15 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"One intel fix, one rockchip fix, and a bunch of radeon fixes for some
regressions from audio rework and vm stability"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915/chv: Implement WaDisableShadowRegForCpd
drm/radeon: fix userptr return value checking (v2)
drm/radeon: check new address before removing old one
drm/radeon: reset BOs address after clearing it.
drm/radeon: fix lockup when BOs aren't part of the VM on release
drm/radeon: add SI DPM quirk for Sapphire R9 270 Dual-X 2G GDDR5
drm/radeon: adjust pll when audio is not enabled
drm/radeon: only enable audio streams if the monitor supports it
drm/radeon: only mark audio as connected if the monitor supports it (v3)
drm/radeon/audio: don't enable packets until the end
drm/radeon: drop dce6_dp_enable
drm/radeon: fix ordering of AVI packet setup
drm/radeon: Use drm_calloc_ab for CS relocs
drm/rockchip: fix error check when getting irq
MAINTAINERS: add entry for Rockchip drm drivers
Dave Airlie [Sun, 3 May 2015 22:56:47 +0000 (08:56 +1000)]
Merge tag 'drm-intel-fixes-2015-04-30' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Just a single intel fix
* tag 'drm-intel-fixes-2015-04-30' of git://anongit.freedesktop.org/drm-intel:
drm/i915/chv: Implement WaDisableShadowRegForCpd
Dave Airlie [Sun, 3 May 2015 22:56:27 +0000 (08:56 +1000)]
Merge branch 'drm-next0420' of https://github.com/markyzq/kernel-drm-rockchip into drm-fixes
one fix and maintainers update
* 'drm-next0420' of https://github.com/markyzq/kernel-drm-rockchip:
drm/rockchip: fix error check when getting irq
MAINTAINERS: add entry for Rockchip drm drivers
Linus Torvalds [Sun, 3 May 2015 20:22:32 +0000 (13:22 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is three logical fixes (as 5 patches).
The 3ware class of drivers were causing an oops with multiqueue by
tearing down the command mappings after completing the command (where
the variables in the command used to tear down the mapping were
no-longer valid). There's also a fix for the qnap iscsi target which
was choking on us sending it commands that were too long and a fix for
the reworked aha1542 allocating GFP_KERNEL under a lock"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
3w-9xxx: fix command completion race
3w-xxxx: fix command completion race
3w-sas: fix command completion race
aha1542: Allocate memory before taking a lock
SCSI: add 1024 max sectors black list flag
Linus Torvalds [Sun, 3 May 2015 17:49:04 +0000 (10:49 -0700)]
Merge branch 'next' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave dmaengine fixes from Vinod Koul:
"Here are the fixes in dmaengine subsystem for rc2:
- privatecnt fix for slave dma request API by Christopher
- warn fix for PM ifdef in usb-dmac by Geert
- fix hardware dependency for xgene by Jean"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: increment privatecnt when using dma_get_any_slave_channel
dmaengine: xgene: Set hardware dependency
dmaengine: usb-dmac: Protect PM-only functions to kill warning
Linus Torvalds [Sun, 3 May 2015 17:28:36 +0000 (10:28 -0700)]
Merge tag 'powerpc-4.1-3' of git://git./linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- build fix for SMP=n in book3s_xics.c
- fix for Daniel's pci_controller_ops on powernv.
- revert the TM syscall abort patch for now.
- CPU affinity fix from Nathan.
- two EEH fixes from Gavin.
- fix for CR corruption from Sam.
- selftest build fix.
* tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Restore non-volatile CRs after nap
powerpc/eeh: Delay probing EEH device during hotplug
powerpc/eeh: Fix race condition in pcibios_set_pcie_reset_state()
powerpc/pseries: Correct cpu affinity for dlpar added cpus
selftests/powerpc: Fix the pmu install rule
Revert "powerpc/tm: Abort syscalls in active transactions"
powerpc/powernv: Fix early pci_controller_ops loading.
powerpc/kvm: Fix SMP=n build error in book3s_xics.c
Jan Kara [Sun, 3 May 2015 03:58:32 +0000 (23:58 -0400)]
ext4: fix growing of tiny filesystems
The estimate of necessary transaction credits in ext4_flex_group_add()
is too pessimistic. It reserves credit for sb, resize inode, and resize
inode dindirect block for each group added in a flex group although they
are always the same block and thus it is enough to account them only
once. Also the number of modified GDT block is overestimated since we
fit EXT4_DESC_PER_BLOCK(sb) descriptors in one block.
Make the estimation more precise. That reduces number of requested
credits enough that we can grow 20 MB filesystem (which has 1 MB
journal, 79 reserved GDT blocks, and flex group size 16 by default).
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Davide Italiano [Sun, 3 May 2015 03:21:15 +0000 (23:21 -0400)]
ext4: move check under lock scope to close a race.
fallocate() checks that the file is extent-based and returns
EOPNOTSUPP in case is not. Other tasks can convert from and to
indirect and extent so it's safe to check only after grabbing
the inode mutex.
Signed-off-by: Davide Italiano <dccitaliano@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Lukas Czerner [Sun, 3 May 2015 01:36:55 +0000 (21:36 -0400)]
ext4: fix data corruption caused by unwritten and delayed extents
Currently it is possible to lose whole file system block worth of data
when we hit the specific interaction with unwritten and delayed extents
in status extent tree.
The problem is that when we insert delayed extent into extent status
tree the only way to get rid of it is when we write out delayed buffer.
However there is a limitation in the extent status tree implementation
so that when inserting unwritten extent should there be even a single
delayed block the whole unwritten extent would be marked as delayed.
At this point, there is no way to get rid of the delayed extents,
because there are no delayed buffers to write out. So when a we write
into said unwritten extent we will convert it to written, but it still
remains delayed.
When we try to write into that block later ext4_da_map_blocks() will set
the buffer new and delayed and map it to invalid block which causes
the rest of the block to be zeroed loosing already written data.
For now we can fix this by simply not allowing to set delayed status on
written extent in the extent status tree. Also add WARN_ON() to make
sure that we notice if this happens in the future.
This problem can be easily reproduced by running the following xfs_io.
xfs_io -f -c "pwrite -S 0xaa 4096 2048" \
-c "falloc 0 131072" \
-c "pwrite -S 0xbb 65536 2048" \
-c "fsync" /mnt/test/fff
echo 3 > /proc/sys/vm/drop_caches
xfs_io -c "pwrite -S 0xdd 67584 2048" /mnt/test/fff
This can be theoretically also reproduced by at random by running fsx,
but it's not very reliable, though on machines with bigger page size
(like ppc) this can be seen more often (especially xfstest generic/127)
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Chanho Park [Sat, 2 May 2015 14:29:22 +0000 (10:29 -0400)]
ext4 crypto: remove duplicated encryption mode definitions
This patch removes duplicated encryption modes which were already in
ext4.h. They were duplicated from commit
3edc18d and commit f542fb.
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Michael Halcrow <mhalcrow@google.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Herbert Xu [Sat, 2 May 2015 14:29:19 +0000 (10:29 -0400)]
ext4 crypto: do not select from EXT4_FS_ENCRYPTION
This patch adds a tristate EXT4_ENCRYPTION to do the selections
for EXT4_FS_ENCRYPTION because selecting from a bool causes all
the selected options to be built-in, even if EXT4 itself is a
module.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Linus Torvalds [Sat, 2 May 2015 03:51:04 +0000 (20:51 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Receive packet length needs to be adjust by 2 on RX to accomodate
the two padding bytes in altera_tse driver. From Vlastimil Setka.
2) If rx frame is dropped due to out of memory in macb driver, we leave
the receive ring descriptors in an undefined state. From Punnaiah
Choudary Kalluri
3) Some netlink subsystems erroneously signal NLM_F_MULTI. That is
only for dumps. Fix from Nicolas Dichtel.
4) Fix mis-use of raw rt->rt_pmtu value in ipv4, one must always go via
the ipv4_mtu() helper. From Herbert Xu.
5) Fix null deref in bridge netfilter, and miscalculated lengths in
jump/goto nf_tables verdicts. From Florian Westphal.
6) Unhash ping sockets properly.
7) Software implementation of BPF divide did 64/32 rather than 64/64
bit divide. The JITs got it right. Fix from Alexei Starovoitov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (30 commits)
ipv4: Missing sk_nulls_node_init() in ping_unhash().
net: fec: Fix RGMII-ID mode
net/mlx4_en: Schedule napi when RX buffers allocation fails
netxen_nic: use spin_[un]lock_bh around tx_clean_lock
net/mlx4_core: Fix unaligned accesses
mlx4_en: Use correct loop cursor in error path.
cxgb4: Fix MC1 memory offset calculation
bnx2x: Delay during kdump load
net: Fix Kernel Panic in bonding driver debugfs file: rlb_hash_table
net: dsa: Fix scope of eeprom-length property
net: macb: Fix race condition in driver when Rx frame is dropped
hv_netvsc: Fix a bug in netvsc_start_xmit()
altera_tse: Correct rx packet length
mlx4: Fix tx ring affinity_mask creation
tipc: fix problem with parallel link synchronization mechanism
tipc: remove wrong use of NLM_F_MULTI
bridge/nl: remove wrong use of NLM_F_MULTI
bridge/mdb: remove wrong use of NLM_F_MULTI
net: sched: act_connmark: don't zap skb->nfct
trivial: net: systemport: bcmsysport.h: fix 0x0x prefix
...
Stefan Hajnoczi [Fri, 1 May 2015 23:12:29 +0000 (08:42 +0930)]
virtio: fix typo in vring_need_event() doc comment
Here the "other side" refers to the guest or host.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rusty Russell [Fri, 1 May 2015 23:12:38 +0000 (08:42 +0930)]
virtio: pass baton to Michael Tsirkin
With my job change kernel work will be "own time"; I'm keeping lguest
and modules (and the virtio standards work), but virtio kernel has to
go.
This makes it clear that Michael is in charge. He's good, but having
me watch over his shoulder won't help.
Good luck Michael!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 2 May 2015 03:35:39 +0000 (20:35 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
Pull Ceph RBD fix from Sage Weil.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: end I/O the entire obj_request on error
David S. Miller [Sat, 2 May 2015 02:02:47 +0000 (22:02 -0400)]
ipv4: Missing sk_nulls_node_init() in ping_unhash().
If we don't do that, then the poison value is left in the ->pprev
backlink.
This can cause crashes if we do a disconnect, followed by a connect().
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Wen Xu <hotdog3645@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilya Dryomov [Sat, 25 Apr 2015 12:56:15 +0000 (15:56 +0300)]
rbd: end I/O the entire obj_request on error
When we end I/O struct request with error, we need to pass
obj_request->length as @nr_bytes so that the entire obj_request worth
of bytes is completed. Otherwise block layer ends up confused and we
trip on
rbd_assert(more ^ (which == img_request->obj_request_count));
in rbd_img_obj_callback() due to more being true no matter what. We
already do it in most cases but we are missing some, in particular
those where we don't even get a chance to submit any obj_requests, due
to an early -ENOMEM for example.
A number of obj_request->xferred assignments seem to be redundant but
I haven't touched any of obj_request->xferred stuff to keep this small
and isolated.
Cc: Alex Elder <elder@linaro.org>
Cc: stable@vger.kernel.org # 3.10+
Reported-by: Shawn Edwards <lesser.evil@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Theodore Ts'o [Fri, 1 May 2015 20:56:50 +0000 (16:56 -0400)]
ext4 crypto: add padding to filenames before encrypting
This obscures the length of the filenames, to decrease the amount of
information leakage. By default, we pad the filenames to the next 4
byte boundaries. This costs nothing, since the directory entries are
aligned to 4 byte boundaries anyway. Filenames can also be padded to
8, 16, or 32 bytes, which will consume more directory space.
Change-Id: Ibb7a0fb76d2c48e2061240a709358ff40b14f322
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Theodore Ts'o [Fri, 1 May 2015 20:56:45 +0000 (16:56 -0400)]
ext4 crypto: simplify and speed up filename encryption
Avoid using SHA-1 when calculating the user-visible filename when the
encryption key is available, and avoid decrypting lots of filenames
when searching for a directory entry in a directory block.
Change-Id: If4655f144784978ba0305b597bfa1c8d7bb69e63
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Linus Torvalds [Fri, 1 May 2015 14:46:21 +0000 (07:46 -0700)]
Merge branch 'for-linus-4.1' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"A few more btrfs fixes.
These range from corners Filipe found in the new free space cache
writeback to a grab bag of fixes from the list"
* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: btrfs_release_extent_buffer_page didn't free pages of dummy extent
Btrfs: fill ->last_trans for delayed inode in btrfs_fill_inode.
btrfs: unlock i_mutex after attempting to delete subvolume during send
btrfs: check io_ctl_prepare_pages return in __btrfs_write_out_cache
btrfs: fix race on ENOMEM in alloc_extent_buffer
btrfs: handle ENOMEM in btrfs_alloc_tree_block
Btrfs: fix find_free_dev_extent() malfunction in case device tree has hole
Btrfs: don't check for delalloc_bytes in cache_save_setup
Btrfs: fix deadlock when starting writeback of bg caches
Btrfs: fix race between start dirty bg cache writeout and bg deletion
Linus Torvalds [Fri, 1 May 2015 14:44:32 +0000 (07:44 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Not too much here, but we've addressed a couple of nasty issues in the
dma-mapping code as well as adding the halfword and byte variants of
load_acquire/store_release following on from the CSD locking bug that
you fixed in the core.
- fix perf devicetree warnings at probe time
- fix memory leak in __dma_free()
- ensure DMA buffers are always zeroed
- show IRQ trigger in /proc/interrupts (for parity with ARM)
- implement byte and halfword access for smp_{load_acquire,store_release}"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: perf: Fix the pmu node name in warning message
arm64: perf: don't warn about missing interrupt-affinity property for PPIs
arm64: add missing PAGE_ALIGN() to __dma_free()
arm64: dma-mapping: always clear allocated buffers
ARM64: Enable CONFIG_GENERIC_IRQ_SHOW_LEVEL
arm64: add missing data types in smp_load_acquire/smp_store_release
Sam Bobroff [Fri, 1 May 2015 06:50:34 +0000 (16:50 +1000)]
powerpc/powernv: Restore non-volatile CRs after nap
Patches
7cba160ad "powernv/cpuidle: Redesign idle states management"
and
77b54e9f2 "powernv/powerpc: Add winkle support for offline cpus"
use non-volatile condition registers (cr2, cr3 and cr4) early in the system
reset interrupt handler (system_reset_pSeries()) before it has been determined
if state loss has occurred. If state loss has not occurred, control returns via
the power7_wakeup_noloss() path which does not restore those condition
registers, leaving them corrupted.
Fix this by restoring the condition registers in the power7_wakeup_noloss()
case.
This is apparent when running a KVM guest on hardware that does not
support winkle or sleep and the guest makes use of secondary threads. In
practice this means Power7 machines, though some early unreleased Power8
machines may also be susceptible.
The secondary CPUs are taken off line before the guest is started and
they call pnv_smp_cpu_kill_self(). This checks support for sleep
states (in this case there is no support) and power7_nap() is called.
When the CPU is woken, power7_nap() returns and because the CPU is
still off line, the main while loop executes again. The sleep states
support test is executed again, but because the tested values cannot
have changed, the compiler has optimized the test away and instead we
rely on the result of the first test, which has been left in cr3
and/or cr4. With the result overwritten, the wrong branch is taken and
power7_winkle() is called on a CPU that does not support it, leading
to it stalling.
Fixes:
7cba160ad789 ("powernv/cpuidle: Redesign idle states management")
Fixes:
77b54e9f213f ("powernv/powerpc: Add winkle support for offline cpus")
[mpe: Massage change log a bit more]
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Thu, 30 Apr 2015 23:22:15 +0000 (09:22 +1000)]
powerpc/eeh: Delay probing EEH device during hotplug
Commit
1c509148b ("powerpc/eeh: Do probe on pci_dn") probes EEH
devices in early stage, which is reasonable to pSeries platform.
However, it's wrong for PowerNV platform because the PE# isn't
determined until the resources (IO and MMIO) are assigned to
PE in hotplug case. So we have to delay probing EEH devices
for PowerNV platform until the PE# is assigned.
Fixes:
ff57b454ddb9 ("powerpc/eeh: Do probe on pci_dn")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Thu, 30 Apr 2015 23:14:11 +0000 (09:14 +1000)]
powerpc/eeh: Fix race condition in pcibios_set_pcie_reset_state()
When asserting reset in pcibios_set_pcie_reset_state(), the PE
is enforced to (hardware) frozen state in order to drop unexpected
PCI transactions (except PCI config read/write) automatically by
hardware during reset, which would cause recursive EEH error.
However, the (software) frozen state EEH_PE_ISOLATED is missed.
When users get 0xFF from PCI config or MMIO read, EEH_PE_ISOLATED
is set in PE state retrival backend. Unfortunately, nobody (the
reset handler or the EEH recovery functinality in host) will clear
EEH_PE_ISOLATED when the PE has been passed through to guest.
The patch sets and clears EEH_PE_ISOLATED properly during reset
in function pcibios_set_pcie_reset_state() to fix the issue.
Fixes:
28158cd ("Enhance pcibios_set_pcie_reset_state()")
Reported-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nathan Fontenot [Thu, 30 Apr 2015 01:42:06 +0000 (20:42 -0500)]
powerpc/pseries: Correct cpu affinity for dlpar added cpus
The incorrect ordering of operations during cpu dlpar add results in invalid
affinity for the cpu being added. The ibm,associativity property in the
device tree is populated with all zeroes for the added cpu which results in
invalid affinity mappings and all cpus appear to belong to node 0.
This occurs because rtas configure-connector is called prior to making the
rtas set-indicator calls. Phyp does not assign affinity information
for a cpu until the rtas set-indicator calls are made to set the isolation
and allocation state.
Correct the order of operations to make the rtas set-indicator
calls (done in dlpar_acquire_drc) before calling rtas configure-connector.
Fixes:
1a8061c46c46 ("powerpc/pseries: Add kernel based CPU DLPAR handling")
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Fri, 1 May 2015 01:10:09 +0000 (11:10 +1000)]
selftests/powerpc: Fix the pmu install rule
My patch to add install support for the powerpc selftests had a typo,
leading to the three tests in the pmu directory itself not being
installed.
Fixes:
6faeeea44b84 ("selftests: Add install support for the powerpc tests")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Linus Torvalds [Thu, 30 Apr 2015 21:23:31 +0000 (14:23 -0700)]
Merge tag 'pm+acpi-4.1-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Three regression fixes this time, one for a recent regression in the
cpuidle core affecting multiple systems, one for an inadvertently
added duplicate typedef in ACPICA that breaks compilation with GCC 4.5
and one for an ACPI Smart Battery Subsystem driver regression
introduced during the 3.18 cycle (stable-candidate).
Specifics:
- Fix for a regression in the cpuidle core introduced by one of the
recent commits in the clockevents_notify() removal series that put
a call to a function which had to be executed with disabled
interrupts into a code path running with enabled interrupts (Rafael
J Wysocki)
- Fix for a build problem in ACPICA (with GCC 4.5) introduced by one
of the recent ACPICA tools commits that added a duplicate typedef
to one of the ACPICA's header files by mistake (Olaf Hering)
- Fix for a regression in the ACPI SBS (Smart Battery Subsystem)
driver introduced during the 3.18 development cycle causing the
smart battery manager to be marked as not present when it should be
marked as present (Chris Bainbridge)"
* tag 'pm+acpi-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: Run tick_broadcast_exit() with disabled interrupts
ACPI / SBS: Enable battery manager when present
ACPICA: remove duplicate u8 typedef
Linus Torvalds [Thu, 30 Apr 2015 21:00:18 +0000 (14:00 -0700)]
Merge tag 'sound-4.1-rc2' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"One nice fix is Peter's patch to make the old good SB Audigy PCI to
work with 32bit DMA instead of 31bit. This allows the MIDI synth
running on modern machines again. Along with it, a few fixes for
emu10k1 have merged.
In ASoC side, there is one fix in the common code, but it's just
trivial additions of static inline functions for CONFIG_PM=n. The
rest are various device-specific small fixes.
Last but not least, a few HD-audio fixes are included, as usual, too"
* tag 'sound-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ASoC: rt5677: fixed wrong DMIC ref clock
ALSA: emu10k1: Emu10k2 32 bit DMA mode
ALSA: emux: Fix mutex deadlock in OSS emulation
ASoC: Update email-id of Rajeev Kumar
ASoC: rt5645: Fix mask for setting RT5645_DMIC_2_DP_GPIO12 bit
ALSA: hda - Fix missing va_end() call in snd_hda_codec_pcm_new()
ALSA: emux: Fix mutex deadlock at unloading
ALSA: emu10k1: Fix card shortname string buffer overflow
ALSA: hda - Add mute-LED mode control to Thinkpad
ALSA: hda - Fix mute-LED fixed mode
ALSA: hda - Fix click noise at start on Dell XPS13
ASoC: rt5645: Add ACPI match ID
ASoC: rt5677: add register patch for PLL
ASoC: Intel: fix the makefile for atom code
ASoC: dapm: Enable autodisable on SOC_DAPM_SINGLE_TLV_AUTODISABLE
ASoC: add static inline funcs to fix a compiling issue
ASoC: Intel: sst_byt: remove kfree for memory allocated with devm_kzalloc
ASoC: samsung: s3c24xx-i2s: Fix return value check in s3c24xx_iis_dev_probe()
ASoC: tfa9879: Fix return value check in tfa9879_i2c_probe()
ASoC: fsl_ssi: Fix platform_get_irq() error handling
...
Markus Pargmann [Thu, 30 Apr 2015 15:07:50 +0000 (17:07 +0200)]
net: fec: Fix RGMII-ID mode
RGMII-ID uses an internal delay within the transmitter or receiver. This
feature is phy specific. The rest of the communication is normal RGMII.
So the fec driver has to check for all RGMII modes, not only
'PHY_INTERFACE_MODE_RGMII'.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 30 Apr 2015 14:32:46 +0000 (17:32 +0300)]
net/mlx4_en: Schedule napi when RX buffers allocation fails
When system is out of memory, refilling of RX buffers fails while
the driver continue to pass the received packets to the kernel stack.
At some point, when all RX buffers deplete, driver may fall into a
sleep, and not recover when memory for new RX buffers is once again
availible. This is because hardware does not have valid descriptors,
so no interrupt will be generated for the driver to return to work
in napi context. Fix it by schedule the napi poll function from
stats_task delayed workqueue, as long as the allocations fail.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Camuso [Thu, 30 Apr 2015 11:51:27 +0000 (07:51 -0400)]
netxen_nic: use spin_[un]lock_bh around tx_clean_lock
While testing this driver with DEBUG_LOCKDEP and DEBUG_SPINLOCK
enabled did not produce any traces, it would be more prudent in the
case of tx_clean_lock to use spin_[un]lock_bh, since this lock is
manipulated in both the process and softirq contexts.
This patch was tested for functionality and regressions with netperf
and DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 29 Apr 2015 20:52:51 +0000 (16:52 -0400)]
net/mlx4_core: Fix unaligned accesses
Addresses the following kernel logs seen during boot:
Kernel unaligned access at TPC[
100ee150] mlx4_QUERY_HCA+0x80/0x248 [mlx4_core]
Kernel unaligned access at TPC[
100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[
100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[
100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[
100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Signed-off-by: David Ahern <david.ahern@oracle.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Poirier [Wed, 29 Apr 2015 22:59:35 +0000 (15:59 -0700)]
mlx4_en: Use correct loop cursor in error path.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Fixes:
9e311e7 ("net/mlx4_en: Use affinity hint")
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rafael J. Wysocki [Thu, 30 Apr 2015 19:05:57 +0000 (21:05 +0200)]
Merge branches 'acpica', 'acpi-battery' and 'pm-cpuidle'
Takashi Iwai [Thu, 30 Apr 2015 17:08:06 +0000 (19:08 +0200)]
Merge tag 'asoc-v4.1-rc1' of git://git./linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.1
A few fixes for v4.1, none earth shattering and mostly driver related
except for one change to fix !PM builds for Intel platforms which is
done by adding stubs in the core so other platforms don't run into the
same issue.
Linus Torvalds [Thu, 30 Apr 2015 16:44:04 +0000 (09:44 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull kvm changes from Paolo Bonzini:
"Remove from guest code the handling of task migration during a pvclock
read; instead use the correct protocol in KVM.
This removes the need for task migration notifiers in core scheduler
code"
[ The scheduler people really hated the migration notifiers, so this was
kind of required - Linus ]
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
x86: pvclock: Really remove the sched notifier for cross-cpu migrations
kvm: x86: fix kvmclock update protocol
Linus Torvalds [Thu, 30 Apr 2015 16:39:52 +0000 (09:39 -0700)]
Merge tag 'dm-4.1-fixes' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper bugfixes from Mike Snitzer:
"Fix two bugs in the request-based DM blk-mq support that was added
during the 4.1 merge"
* tag 'dm-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix free_rq_clone() NULL pointer when requeueing unmapped request
dm: only initialize the request_queue once
David Howells [Thu, 30 Apr 2015 13:58:43 +0000 (14:58 +0100)]
modsign: change default key details
Change default key details to be more obviously unspecified.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 30 Apr 2015 16:30:07 +0000 (09:30 -0700)]
Merge tag 'tty-4.1-rc2' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty/serial driver fixes for 4.1-rc2.
They include some minor fixes that resolve reported issues, and a new
device quirk.
All have been in linux-next succesfully"
* tag 'tty-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_pci: Add support for 16 port Exar boards
serial: samsung: fix serial console break
tty/serial: at91: maxburst was missing for dma transfers
serial: of-serial: Remove device_type = "serial" registration
serial: xilinx: Use platform_get_irq to get irq description structure
serial: core: Fix kernel-doc build warnings
tty: Re-add external interface for tty_set_termios()
Linus Torvalds [Thu, 30 Apr 2015 16:08:53 +0000 (09:08 -0700)]
Merge tag 'usb-4.1-rc2' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for 4.2-rc2. They revert one
problem patch, fix some minor things, and add some new quirks for
"broken" devices.
All have been in linux-next successfully"
* tag 'usb-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
cdc-acm: prevent infinite loop when parsing CDC headers.
Revert "usb: host: ehci-msm: Use devm_ioremap_resource instead of devm_ioremap"
usb: chipidea: otg: remove mutex unlock and lock while stop and start role
uas: Set max_sectors_240 quirk for ASM1053 devices
uas: Add US_FL_MAX_SECTORS_240 flag
uas: Allow uas_use_uas_driver to return usb-storage flags
Linus Torvalds [Thu, 30 Apr 2015 16:07:26 +0000 (09:07 -0700)]
Merge tag 'renesas-sh-drivers-for-v4.1' of git://git./linux/kernel/git/horms/renesas
Pull SH driver updates from Simon Horman:
- remove test for now unsupported sh7372 SoC
- disable PM runtime for multi-platform r8a73a4 and sh73a0 SoCs with
genpd
* tag 'renesas-sh-drivers-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
drivers: sh: Remove test for now unsupported sh7372
drivers: sh: Disable PM runtime for multi-platform r8a73a4 with genpd
drivers: sh: Disable PM runtime for multi-platform sh73a0 with genpd
Mike Snitzer [Wed, 29 Apr 2015 14:48:09 +0000 (10:48 -0400)]
dm: fix free_rq_clone() NULL pointer when requeueing unmapped request
Commit
022333427a ("dm: optimize dm_mq_queue_rq to _not_ use kthread if
using pure blk-mq") mistakenly removed free_rq_clone()'s clone->q check
before testing clone->q->mq_ops. It was an oversight to discontinue
that check for 1 of the 2 use-cases for free_rq_clone():
1) free_rq_clone() called when an unmapped original request is requeued
2) free_rq_clone() called in the request-based IO completion path
The clone->q check made sense for case #1 but not for #2. However, we
cannot just reinstate the check as it'd mask a serious bug in the IO
completion case #2 -- no in-flight request should have an uninitialized
request_queue (basic block layer refcounting _should_ ensure this).
The NULL pointer seen for case #1 is detailed here:
https://www.redhat.com/archives/dm-devel/2015-April/msg00160.html
Fix this free_rq_clone() NULL pointer by simply checking if the
mapped_device's type is DM_TYPE_MQ_REQUEST_BASED (clone's queue is
blk-mq) rather than checking clone->q->mq_ops. This avoids the need to
dereference clone->q, but a WARN_ON_ONCE is added to let us know if an
uninitialized clone request is being completed.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Christoph Hellwig [Thu, 30 Apr 2015 14:10:36 +0000 (10:10 -0400)]
dm: only initialize the request_queue once
Commit
bfebd1cdb4 ("dm: add full blk-mq support to request-based DM")
didn't properly account for the need to short-circuit re-initializing
DM's blk-mq request_queue if it was already initialized.
Otherwise, reloading a blk-mq request-based DM table (either manually
or via multipathd) resulted in errors, see:
https://www.redhat.com/archives/dm-devel/2015-April/msg00132.html
Fix is to only initialize the request_queue on the initial table load
(when the mapped_device type is assigned).
This is better than having dm_init_request_based_blk_mq_queue() return
early if the queue was already initialized because it elevates the
constraint to a more meaningful location in DM core. As such the
pre-existing early return in dm_init_request_based_queue() can now be
removed.
Fixes:
bfebd1cdb4 ("dm: add full blk-mq support to request-based DM")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Suzuki K. Poulose [Mon, 13 Apr 2015 09:17:55 +0000 (10:17 +0100)]
arm64: perf: Fix the pmu node name in warning message
With commit
d5efd9cc9cf2 ("arm64: pmu: add support for interrupt-affinity
property"), we print a warning when we find a PMU SPI with a missing
missing interrupt-affinity property in a pmu node. Unfortunately, we
pass the wrong (NULL) device node to of_node_full_name, resulting in
unhelpful messages such as:
hw perfevents: Failed to parse <no-node>/interrupt-affinity[0]
This patch fixes the name to that of the pmu node.
Fixes:
d5efd9cc9cf2 (arm64: pmu: add support for interrupt-affinity property)
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Will Deacon [Fri, 17 Apr 2015 13:41:29 +0000 (14:41 +0100)]
arm64: perf: don't warn about missing interrupt-affinity property for PPIs
PPIs are affine by nature, so the interrupt-affinity property is not
used and therefore we shouldn't print a warning in its absence.
Reported-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Michael Ellerman [Thu, 30 Apr 2015 05:13:14 +0000 (15:13 +1000)]
Revert "powerpc/tm: Abort syscalls in active transactions"
This reverts commit
feba40362b11341bee6d8ed58d54b896abbd9f84.
Although the principle of this change is good, the implementation has a
few issues.
Firstly we can sometimes fail to abort a syscall because r12 may have
been clobbered by C code if we went down the virtual CPU accounting
path, or if syscall tracing was enabled.
Secondly we have decided that it is safer to abort the syscall even
earlier in the syscall entry path, so that we avoid the syscall tracing
path when we are transactional.
So that we have time to thoroughly test those changes we have decided to
revert this for this merge window and will merge the fixed version in
the next window.
NB. Rather than reverting the selftest we just drop tm-syscall from
TEST_PROGS so that it's not run by default.
Fixes:
feba40362b11 ("powerpc/tm: Abort syscalls in active transactions")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Dave Airlie [Thu, 30 Apr 2015 02:15:34 +0000 (12:15 +1000)]
Merge branch 'drm-fixes-4.1' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Fixes for 4.1 for radeon all destined for stable:
- fix fallout from the audio rework
- VM fixes
- other assorted bug fixes
* 'drm-fixes-4.1' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix userptr return value checking (v2)
drm/radeon: check new address before removing old one
drm/radeon: reset BOs address after clearing it.
drm/radeon: fix lockup when BOs aren't part of the VM on release
drm/radeon: add SI DPM quirk for Sapphire R9 270 Dual-X 2G GDDR5
drm/radeon: adjust pll when audio is not enabled
drm/radeon: only enable audio streams if the monitor supports it
drm/radeon: only mark audio as connected if the monitor supports it (v3)
drm/radeon/audio: don't enable packets until the end
drm/radeon: drop dce6_dp_enable
drm/radeon: fix ordering of AVI packet setup
drm/radeon: Use drm_calloc_ab for CS relocs
Forrest Liu [Mon, 9 Feb 2015 09:31:45 +0000 (17:31 +0800)]
Btrfs: btrfs_release_extent_buffer_page didn't free pages of dummy extent
btrfs_release_extent_buffer_page() can't handle dummy extent that
allocated by btrfs_clone_extent_buffer() properly. That is because
reference count of pages that allocated by btrfs_clone_extent_buffer()
was 2, 1 by alloc_page(), and another by attach_extent_buffer_page().
Running following command repeatly can check this memory leak problem
btrfs inspect-internal inode-resolve 256 /mnt/btrfs
Signed-off-by: Chien-Kuan Yeh <ckya@synology.com>
Signed-off-by: Forrest Liu <forrestl@synology.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Tested-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Hariprasad Shenai [Wed, 29 Apr 2015 11:49:05 +0000 (17:19 +0530)]
cxgb4: Fix MC1 memory offset calculation
Commit
6559a7e8296002b4 ("cxgb4: Cleanup macros so they follow the same
style and look consistent") introduced a regression where reading MC1
memory in adapters where MC0 isn't present or MC0 size is not equal to MC1
size caused the adapter to crash due to incorrect computation of memoffset.
Fix is to read the size of MC0 instead of MC1 for offset calculation
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Wed, 29 Apr 2015 05:09:49 +0000 (08:09 +0300)]
bnx2x: Delay during kdump load
In a kdump environment interfaces might be re-loaded without a proper
unload sequence in the previous running kernel.
bnx2x management FW and driver maintains a `pulse' that notifies the FW
that the driver is still up and running.
Driver load on the kdump kernel should be performed only after the pulse
has been out-of-sync long enough for the management FW to identify that
the driver has crashed, on which point it will perform some necessary
cleanup of the HW.
In today's distros kdump loading is quite fast, sometimes too fast for our
FW to get out-of-sync. This patch delays the bnx2x's probe during kdump
to allow a proper re-load on the kdump kernel.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pai [Wed, 29 Apr 2015 18:24:23 +0000 (14:24 -0400)]
net: Fix Kernel Panic in bonding driver debugfs file: rlb_hash_table
This patch fixes a Kernel Panic in bonding driver debugfs file: rlb_hash_table.
$> modprobe bonding mode=6
$> cat /sys/kernel/debug/bonding/bond0/rlb_hash_table
This will crash the kernel. The struct alb_bond_info is initialized only when
the bonding interface is initialized (ip link set bond0 up) and not at the time
it is allocated. If we try to read the table before that, it'll result in a
kernel panic.
The patch applies against both net and net-next
Signed-off-by: Vishwanath Pai <vpai@akamai.com>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Wed, 29 Apr 2015 17:56:15 +0000 (10:56 -0700)]
net: dsa: Fix scope of eeprom-length property
eeprom-length is a switch property, not a dsa property, and thus
needs to be attached to the switch node, not to the dsa node.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Fixes:
6793abb4e849 ("net: dsa: Add support for switch EEPROM access")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Punnaiah Choudary Kalluri [Wed, 29 Apr 2015 03:04:46 +0000 (08:34 +0530)]
net: macb: Fix race condition in driver when Rx frame is dropped
Under heavy Rx load, observed that the Hw is updating the USED bit
and it is not updating the received frame status to the BD control
field. This could be lack of resources for processing the BDs at high
data rates. Driver drops the frame associated with this BD but not
clearing the USED bit. So, this is causing hang condition as Hw
expects USED bit to be cleared for this BD.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 29 Apr 2015 00:59:48 +0000 (17:59 -0700)]
hv_netvsc: Fix a bug in netvsc_start_xmit()
Commit
b08cc79155fc26d0d112b1470d1ece5034651a4b eliminated memory
allocation in the packet send path:
"hv_netvsc: Eliminate memory allocation in the packet send path
The network protocol used to communicate with the host is the remote ndis (rndis)
protocol. We need to decorate each outgoing packet with a rndis header and
additional rndis state (rndis per-packet state). To manage this state, we
currently allocate memory in the transmit path. Eliminate this allocation by
requesting additional head room in the skb."
This commit introduced a bug since it did not account for the case if the skb
was cloned. Fix this bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlastimil Setka [Tue, 28 Apr 2015 22:17:11 +0000 (00:17 +0200)]
altera_tse: Correct rx packet length
Altera TSE MAC rx DMA transfer starts with the 2 additional bytes for IP
payload alignment. This patch fixes tse_rx() function loop which reads DMA
rx status and extracts packet length from it. Status signalises a whole DMA
transfer length, which is 2 bytes longer than the packet itself.
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Poirier [Tue, 28 Apr 2015 21:49:29 +0000 (14:49 -0700)]
mlx4: Fix tx ring affinity_mask creation
By default, the number of tx queues is limited by the number of online cpus
in mlx4_en_get_profile(). However, this limit no longer holds after the
ethtool .set_channels method has been called. In that situation, the driver
may access invalid bits of certain cpumask variables when queue_index >=
nr_cpu_ids.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Acked-by: Ido Shamay <idos@mellanox.com>
Fixes:
d03a68f ("net/mlx4_en: Configure the XPS queue mapping on driver load")
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Tue, 28 Apr 2015 20:59:04 +0000 (16:59 -0400)]
tipc: fix problem with parallel link synchronization mechanism
Currently, we try to accumulate arrived packets in the links's
'deferred' queue during the parallel link syncronization phase.
This entails two problems:
- With an unlucky combination of arriving packets the algorithm
may go into a lockstep with the out-of-sequence handling function,
where the synch mechanism is adding a packet to the deferred queue,
while the out-of-sequence handling is retrieving it again, thus
ending up in a loop inside the node_lock scope.
- Even if this is avoided, the link will very often send out
unnecessary protocol messages, in the worst case leading to
redundant retransmissions.
We fix this by just dropping arriving packets on the upcoming link
during the synchronization phase, thus relying on the retransmission
protocol to resolve the situation once the two links have arrived to
a synchronized state.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Tue, 28 Apr 2015 16:33:50 +0000 (18:33 +0200)]
tipc: remove wrong use of NLM_F_MULTI
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes:
35b9dd7607f0 ("tipc: add bearer get/dump to new netlink api")
Fixes:
7be57fc69184 ("tipc: add link get/dump to new netlink api")
Fixes:
46f15c6794fb ("tipc: add media get/dump to new netlink api")
CC: Richard Alpe <richard.alpe@ericsson.com>
CC: Jon Maloy <jon.maloy@ericsson.com>
CC: Ying Xue <ying.xue@windriver.com>
CC: tipc-discussion@lists.sourceforge.net
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Tue, 28 Apr 2015 16:33:49 +0000 (18:33 +0200)]
bridge/nl: remove wrong use of NLM_F_MULTI
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes:
e5a55a898720 ("net: create generic bridge ops")
Fixes:
815cccbf10b2 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Tue, 28 Apr 2015 16:33:48 +0000 (18:33 +0200)]
bridge/mdb: remove wrong use of NLM_F_MULTI
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes:
37a393bc4932 ("bridge: notify mdb changes via netlink")
CC: Cong Wang <amwang@redhat.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Tue, 28 Apr 2015 11:33:21 +0000 (13:33 +0200)]
net: sched: act_connmark: don't zap skb->nfct
This action is meant to be passive, i.e. we should not alter
skb->nfct: If nfct is present just leave it alone.
Compile tested only.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antonio Ospite [Tue, 28 Apr 2015 11:11:29 +0000 (13:11 +0200)]
trivial: net: systemport: bcmsysport.h: fix 0x0x prefix
Fix the 0x0x prefix in an integer constant.
In this case, while at it, also fix a typo (s/unitcast/unicast/).
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Antonio Ospite [Tue, 28 Apr 2015 11:11:27 +0000 (13:11 +0200)]
trivial: net: atl1e: atl1e_hw.h: fix 0x0x prefix
Fix the 0x0x prefix in an integer constant.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 29 Apr 2015 18:48:36 +0000 (14:48 -0400)]
Merge branch 'bnx2x'
Michal Schmidt says:
====================
bnx2x: minor cleanups related to TPA bits
I noticed some simplification possibilities while looking into the bug
fixed by "bnx2x: really disable TPA if 'disable_tpa' is set'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Tue, 28 Apr 2015 09:34:23 +0000 (11:34 +0200)]
bnx2x: remove {TPA,GRO}_ENABLE_FLAG
These flags are redundant with dev->features. Remove them.
Just make sure to set dev->features ourselves in bnx2x_set_features()
before performing the reload of the card.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>