OSDN Git Service
Ido Schimmel [Tue, 14 Jul 2020 14:21:01 +0000 (17:21 +0300)]
mlxsw: spectrum_span: Allow setting policer on a SPAN agent
When mirroring packets to the CPU port the mirrored packets are trapped
to the CPU. However, unlike other traps, it is not possible to set a
policer on the associated trap group. Instead, the policer needs to be
set on the SPAN agent.
Moreover, the policer ID must be within a specified range: From a
configurable (even) base ID to this base plus the maximum number of SPAN
agents.
While the immediate use case is to set the policer on a SPAN agent that
mirrors to the CPU port, a policer can be set on any SPAN agent.
Therefore, the operation is implemented for all SPAN agent types.
Extend the SPAN agent request API to allow passing the desired policer
ID that should be bound to the SPAN agent. Return an error for
Spectrum-1, as it does not support policer setting on a SPAN agent.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 14 Jul 2020 14:21:00 +0000 (17:21 +0300)]
mlxsw: spectrum_span: Allow passing parameters to SPAN agents
Currently, the only parameter of a SPAN agent is the netdev which
the SPAN agent should mirror to.
The next patch will add the ability to request a SPAN agent that mirrors
to a specific netdev and has a specific policer ID bound to it. This is
required when mirroring packets to the CPU port.
Therefore, encapsulate the sole parameter to mlxsw_sp_span_agent_get()
in a structure, so that it could later be extended with policer
information.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 14 Jul 2020 14:20:59 +0000 (17:20 +0300)]
mlxsw: spectrum_span: Add support for mirroring towards CPU port
The Spectrum-2 and Spectrum-3 ASICs are able to mirror packets towards
the CPU. These packets are then trapped like any other packet, but with
a special packet trap and additional metadata such as why the packet was
mirrored.
The ability to mirror packets towards the CPU will be utilized by a
subsequent patch set that will mirror packets that were dropped by the
ASIC for various buffer-related reasons, such as tail-drop and
early-drop.
Add mirroring towards the CPU as a new SPAN agent type and re-use the
functions that mirror to a physical port where possible.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 14 Jul 2020 14:20:58 +0000 (17:20 +0300)]
mlxsw: spectrum_span: Do not dereference destination netdev
Currently, the destination netdev to which we mirror must be a valid
netdev. However, this is going to change with the introduction of
mirroring towards the CPU port, as the CPU port does not have a backing
netdev.
Avoid dereferencing the destination netdev when it is not clear if it is
valid or not.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 14 Jul 2020 14:20:57 +0000 (17:20 +0300)]
mlxsw: spectrum_span: Add driver private info to parms_set() callback
The parms_set() callback is supposed to fill in the parameters for the
SPAN agent, such as the destination port and encapsulation info, if any.
When mirroring to the CPU port we cannot resolve the destination port
(the CPU port) without access to the driver private info.
Pass the driver private info to parms_set() callback so that it could be
used later on to resolve the CPU port.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 14 Jul 2020 14:20:56 +0000 (17:20 +0300)]
mlxsw: spectrum_span: Add per-ASIC SPAN agent operations
The various SPAN agent types differ in their mirror targets (i.e.,
physical port netdev vs. VLAN netdev) and the encapsulation headers that
they need to encapsulate the mirrored packets with.
The Spectrum-2 and Spectrum-3 ASICs support a SPAN agent type that is
able to mirror towards the CPU, whereas the Spectrum-1 ASIC does not.
Prepare for the addition of this new SPAN agent type by splitting the
SPAN agent operations to be per-ASIC.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Tue, 14 Jul 2020 14:20:55 +0000 (17:20 +0300)]
mlxsw: reg: add mirroring_pid_base to MOGCR register
Allow setting mirroring_pid_base using MOGCR register.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Tue, 14 Jul 2020 14:20:54 +0000 (17:20 +0300)]
mlxsw: reg: Add session_id and pid to MPAT register
Allow setting session_id and pid as part of port analyzer
configurations.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Tue, 14 Jul 2020 09:14:12 +0000 (11:14 +0200)]
net: neterion: vxge: switch from 'pci_' to 'dma_' API
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below. No GFP_
flag needs to be corrected.
It has been compile tested.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Tue, 14 Jul 2020 09:06:20 +0000 (11:06 +0200)]
net: neterion: s2io: switch from 'pci_' to 'dma_' API
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GPF_ with a correct flag.
It has been compile tested.
When memory is allocated in 'init_shared_mem()' GFP_KERNEL can be used
because this flag is already used to allocate some memory in this function.
While at it, update some debug message to match the new function names.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Tue, 14 Jul 2020 07:52:24 +0000 (09:52 +0200)]
lan743x: switch from 'pci_' to 'dma_' API
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GPF_ with a correct flag.
It has been compile tested.
When memory is allocated in 'lan743x_tx_ring_cleanup()' and
'lan743x_rx_ring_init()', GFP_KERNEL can be used because this flag is
already used to allocate some memory in these functions.
While at it, remove a useless (void *) casting in the first hunk in so that
the code is more consistent.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 14 Jul 2020 20:46:43 +0000 (13:46 -0700)]
Merge branch 'bridge-mrp-Add-support-for-interconnect-ring'
Horatiu Vultur says:
====================
bridge: mrp: Add support for interconnect ring
This patch series extends existing MRP to add support for interconnect ring. An
interconnect ring is a ring that connects 2 rings. In this way is possible to
connect multiple rings. Each interconnect ring is form of 4 nodes, in which 3
have the role MIC(Media Redundancy Interconnect Client) and one has the role
MIM(Media Redundancy Interconnect Manager). All these nodes need to have the
same ID and the ID needs to be unique between multiple interconnect rings. And 2
nodes needs to be part of one ring and the other 2 nodes needs to be part of the
other ring that is connected.
+---------+
| |
+----------| MRM |---------------+
| | | |
| +---------+ |
| |
| |
| |
+--------------+ +-----------------+
| | | |
| MRC/MIC |------------------| MRC/MIM |
| | | |
+--------------+ +-----------------+
| |
|Interconnect port |Interconnect port
| |
| |
+--------------+ +-----------------+
| | | |
| MRC/MIC |----------------- | MRC/MIC |
| | | |
+--------------+ +-----------------+
| |
| |
| +---------+ |
| | | |
+----------| MRM |----------------+
| |
+---------+
Each node in a ring needs to have one of the following ring roles, MRM or MRC.
And it can also have an interconnect role like MIM or MIC if it is part of an
interconnect ring. In the figure above the MRM doesn't have any interconnect
role but the MRC from the top ring have the interconnect roles MIC respectively
MIM. Therefore it is not possible for a node to have only an interconnect role.
There are 2 ways for interconnect ring to detect when is open or closed:
1. To use CCM frames on the interconnect port to detect when the interconnect
link goes down/up. This mode is called LC-mode.
2. To send InTest frames on all 3 ports(2 ring ports and 1 interconnect port)
and detect when these frames are received back. This mode is called RC-mode.
This patch series adds support only for RC-mode. Where MIM sends InTest frames
on all 3 ports and detects when it receives back the InTest. When it receives
the InTest it means that the ring is closed so it would set the interconnect
port in blocking state. If it stops receiving the InTest frames then it would
set the port in forwarding state and it would send InTopo frames. These InTopo
frames will be received by MRM nodes and process them. And then the MRM will
send Topo frames in the rings so each client will clear its FDB.
v4:
- always cancel delay work if the MRP instance is deleted or interconnect role
is disabled but allow only to start to send InTest frames only if the role
is MIM.
v3:
- update 'br_mrp_set_in_role' to stop sending test if the role is disabled
and don't allow to set a different interconnect port if there is already
one.
v2:
- rearrange structures not to contain holes
- stop sending MRP_InTest frames when the MRP instance is deleted
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:58 +0000 (09:34 +0200)]
net: bridge: Add port attribute IFLA_BRPORT_MRP_IN_OPEN
This patch adds a new port attribute, IFLA_BRPORT_MRP_IN_OPEN, which
allows to notify the userspace when the node lost the contiuity of
MRP_InTest frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:57 +0000 (09:34 +0200)]
bridge: mrp: Extend br_mrp_fill_info
This patch extends the function br_mrp_fill_info to return also the
status for the interconnect ring.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:56 +0000 (09:34 +0200)]
bridge: uapi: mrp: Extend MRP_INFO attributes for interconnect status
Extend the existing MRP_INFO to return status of MRP interconnect. In
case there is no MRP interconnect on the node then the role will be
disabled so the other attributes can be ignored.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:55 +0000 (09:34 +0200)]
bridge: mrp: Extend MRP netlink interface for configuring MRP interconnect
This patch extends the existing MRP netlink interface with the following
attributes: IFLA_BRIDGE_MRP_IN_ROLE, IFLA_BRIDGE_MRP_IN_STATE and
IFLA_BRIDGE_MRP_START_IN_TEST. These attributes are similar with their
ring attributes but they apply to the interconnect port.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:54 +0000 (09:34 +0200)]
bridge: mrp: Implement the MRP Interconnect API
Thie patch adds support for MRP Interconnect. Similar with the MRP ring,
if the HW can't generate MRP_InTest frames, then the SW will try to
generate them. And if also the SW fails to generate the frames then an
error is return to userspace.
The forwarding/termination of MRP_In frames is happening in the kernel
and is done by MRP instances.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:53 +0000 (09:34 +0200)]
bridge: switchdev: mrp: Extend MRP API for switchdev for MRP Interconnect
Implement the MRP API for interconnect switchdev. Similar with the other
br_mrp_switchdev function, these function will just eventually call the
switchdev functions: switchdev_port_obj_add/del.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:52 +0000 (09:34 +0200)]
bridge: mrp: Add br_mrp_in_port_open function
This function notifies the userspace when the node lost the continuity
of MRP_InTest frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:51 +0000 (09:34 +0200)]
bridge: mrp: Rename br_mrp_port_open to br_mrp_ring_port_open
This patch renames the function br_mrp_port_open to
br_mrp_ring_port_open. In this way is more clear that a ring port lost
the continuity because there will be also a br_mrp_in_port_open.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:50 +0000 (09:34 +0200)]
bridge: mrp: Extend br_mrp for MRP interconnect
This patch extends the 'struct br_mrp' to contain information regarding
the MRP interconnect. It contains the following:
- the interconnect port 'i_port', which is NULL if the node doesn't have
a interconnect role
- the interconnect id, which is similar with the ring id, but this field
is also part of the MRP_InTest frames.
- the interconnect role, which can be MIM or MIC.
- the interconnect state, which can be open or closed.
- the interconnect delayed_work for sending MRP_InTest frames and check
for lost of continuity.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:49 +0000 (09:34 +0200)]
bridge: mrp: Extend bridge interface
This patch adds a new flag(BR_MRP_LOST_IN_CONT) to the net bridge
ports. This bit will be set when the port lost the continuity of
MRP_InTest frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:48 +0000 (09:34 +0200)]
bridge: uapi: mrp: Extend MRP attributes for MRP interconnect
Extend the existing MRP netlink attributes to allow to configure MRP
Interconnect:
IFLA_BRIDGE_MRP_IN_ROLE - the parameter type is br_mrp_in_role which
contains the interconnect id, the ring id, the interconnect role(MIM
or MIC) and the port ifindex that represents the interconnect port.
IFLA_BRIDGE_MRP_IN_STATE - the parameter type is br_mrp_in_state which
contains the interconnect id and the interconnect state.
IFLA_BRIDGE_MRP_IN_TEST - the parameter type is br_mrp_start_in_test
which contains the interconnect id, the interval at which to send
MRP_InTest frames, how many test frames can be missed before declaring
the interconnect ring open and the period which represents for how long
to send MRP_InTest frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:47 +0000 (09:34 +0200)]
switchdev: mrp: Extend switchdev API for MRP Interconnect
Extend switchdev API to add support for MRP interconnect. The HW is
notified in the following cases:
SWITCHDEV_OBJ_ID_IN_ROLE_MRP: This is used when the interconnect role
of the node changes. The supported roles are MIM and MIC.
SWITCHDEV_OBJ_ID_IN_STATE_MRP: This is used when the interconnect ring
changes it states to open or closed.
SWITCHDEV_OBJ_ID_IN_TEST_MRP: This is used to start/stop sending
MRP_InTest frames on all MRP ports. This is called only on nodes that
have the interconnect role MIM.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 14 Jul 2020 01:04:05 +0000 (18:04 -0700)]
Merge git://git./linux/kernel/git/bpf/bpf-next
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-07-13
The following pull-request contains BPF updates for your *net-next* tree.
We've added 36 non-merge commits during the last 7 day(s) which contain
a total of 62 files changed, 2242 insertions(+), 468 deletions(-).
The main changes are:
1) Avoid trace_printk warning banner by switching bpf_trace_printk to use
its own tracing event, from Alan.
2) Better libbpf support on older kernels, from Andrii.
3) Additional AF_XDP stats, from Ciara.
4) build time resolution of BTF IDs, from Jiri.
5) BPF_CGROUP_INET_SOCK_RELEASE hook, from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander A. Klimov [Mon, 13 Jul 2020 20:48:12 +0000 (22:48 +0200)]
wan: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Mon, 13 Jul 2020 20:18:45 +0000 (22:18 +0200)]
pcnet32: switch from 'pci_' to 'dma_' API
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GPF_ with a correct flag.
It has been compile tested.
When memory is allocated in 'pcnet32_realloc_tx_ring()' and
'pcnet32_realloc_rx_ring()', GFP_ATOMIC must be used because a spin_lock is
hold.
The call chain is:
pcnet32_set_ringparam
** spin_lock_irqsave(&lp->lock, flags);
--> pcnet32_realloc_tx_ring
--> pcnet32_realloc_rx_ring
** spin_unlock_irqrestore(&lp->lock, flags);
When memory is in 'pcnet32_probe1()' and 'pcnet32_alloc_ring()', GFP_KERNEL
can be used.
While at it, update a few comments and pr_err messages to be more in line
with the new function names.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Mon, 13 Jul 2020 19:55:03 +0000 (21:55 +0200)]
amd8111e: switch from 'pci_' to 'dma_' API
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GPF_ with a correct flag.
It has been compile tested.
When memory is allocated in 'amd8111e_init_ring()', GFP_ATOMIC must be used
because a spin_lock is hold.
One of the call chains is:
amd8111e_open
** spin_lock_irq(&lp->lock);
--> amd8111e_restart
--> amd8111e_init_ring
** spin_unlock_irq(&lp->lock);
The rest of the patch is produced by coccinelle with a few adjustments to
please checkpatch.pl.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander A. Klimov [Mon, 13 Jul 2020 17:34:47 +0000 (19:34 +0200)]
net: wan: cosa: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander A. Klimov [Mon, 13 Jul 2020 17:24:39 +0000 (19:24 +0200)]
net: jme: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander A. Klimov [Mon, 13 Jul 2020 17:14:29 +0000 (19:14 +0200)]
net: ethernet: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 14 Jul 2020 00:40:02 +0000 (17:40 -0700)]
Merge branch 'New-DSA-driver-for-VSC9953-Seville-switch'
Vladimir Oltean says:
====================
New DSA driver for VSC9953 Seville switch
Looking at the Felix and Ocelot drivers, Maxim asked if it would be
possible to use them as a base for a new driver for the Seville switch
inside NXP T1040. Turns out, it is! The result is that the mscc_felix
driver was extended to probe on Seville.
The biggest challenge seems to be getting register read/write API
generic enough to cover such wild bitfield variations between hardware
generations.
Currently, both felix and seville are built under the same kernel config
option (NET_DSA_MSCC_FELIX). This has both some advantages (no need to
duplicate the Lynx PCS code from felix_vsc9959.c) and some disadvantages
(Seville needs to depend on PCI and on ENETC_MDIO). This will be further
refined as time progresses.
The driver has been completely reviewed. Previous submission was here,
it wasn't accepted due to a conflict with Mark Brown's tree, very late
in the release cycle:
https://patchwork.ozlabs.org/project/netdev/cover/
20200531122640.
1375715-1-olteanv@gmail.com/
So this is more of a repost, with the only changes being related to
rebasing on top of the cleanup I had to do in Ocelot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:11 +0000 (19:57 +0300)]
docs: devicetree: add bindings for Seville DSA switch inside Felix driver
There are no non-standard bindings being used. However Felix is a PCI
device and Seville is a platform device. So give an example of device
tree for this switch and document its compatible string.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Kochetkov [Mon, 13 Jul 2020 16:57:10 +0000 (19:57 +0300)]
net: dsa: felix: introduce support for Seville VSC9953 switch
This is another switch from Vitesse / Microsemi / Microchip, that has
10 ports (8 external, 2 internal) and is integrated into the Freescale /
NXP T1040 PowerPC SoC. It is very similar to Felix from NXP LS1028A,
except that this is a platform device and Felix is a PCI device, and it
doesn't support IEEE 1588 and TSN.
Like Felix, this driver configures its own PCS on the internal MDIO bus
using a phy_device abstraction for it (yes, it will be refactored to use
a raw mdio_device, like other phylink drivers do, but let's keep it like
that for now). But unlike Felix, the MDIO bus and the PCS are not from
the same vendor. The PCS is the same QorIQ/Layerscape PCS as found in
Felix/ENETC/DPAA*, but the internal MDIO bus that is used to access it
is actually an instantiation of drivers/net/phy/mdio-mscc-miim.c. But it
would be difficult to reuse that driver (it doesn't even use regmap, and
it's less than 200 lines of code), so we hand-roll here some internal
MDIO bus accessors within seville_vsc9953.c, which serves the purpose of
driving the PCS absolutely fine.
Also, same as Felix, the PCS doesn't support dynamic reconfiguration of
SerDes protocol, so we need to do pre-validation of PHY mode from device
tree and not let phylink change it.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:09 +0000 (19:57 +0300)]
net: dsa: felix: move probing to felix_vsc9959.c
Felix is not actually meant to be a DSA driver only for the switch
inside NXP LS1028A, but an umbrella for all Vitesse / Microsemi /
Microchip switches that are register-compatible with Ocelot and that are
using in DSA mode (with an NPI Ethernet port).
For the dsa_switch_ops exported by the felix driver to be generic enough
to be used by other non-PCI switches, we need to move the PCI-specific
probing to the low-level translation module felix_vsc9959.c. This way,
other switches can have their own probing functions, as platform devices
or otherwise.
This patch also removes the "Felix instance table", which did not stand
the test of time and is unnecessary at this point.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Kochetkov [Mon, 13 Jul 2020 16:57:08 +0000 (19:57 +0300)]
net: mscc: ocelot: extend watermark encoding function
The ocelot_wm_encode function deals with setting thresholds for pause
frame start and stop. In Ocelot and Felix the register layout is the
same, but for Seville, it isn't. The easiest way to accommodate Seville
hardware configuration is to introduce a function pointer for setting
this up.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Kochetkov [Mon, 13 Jul 2020 16:57:07 +0000 (19:57 +0300)]
net: mscc: ocelot: convert SYS_PAUSE_CFG register access to regfield
Seville has a different bitwise layout than Ocelot and Felix.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:06 +0000 (19:57 +0300)]
net: mscc: ocelot: disable flow control on NPI interface
The Ocelot switches do not support flow control on Ethernet interfaces
where a DSA tag must be added. If pause frames are enabled, they will be
encapsulated in the DSA tag just like regular frames, and the DSA master
will not recognize them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:05 +0000 (19:57 +0300)]
net: mscc: ocelot: split writes to pause frame enable bit and to thresholds
We don't want ocelot_port_set_maxlen to enable pause frame TX, just to
adjust the pause thresholds.
Move the unconditional enabling of pause TX to ocelot_init_port. There
is no good place to put such setting because it shouldn't be
unconditional. But at the moment it is, we're not changing that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:04 +0000 (19:57 +0300)]
net: dsa: felix: create a template for the DSA tags on xmit
With this patch we try to kill 2 birds with 1 stone.
First of all, some switches that use tag_ocelot.c don't have the exact
same bitfield layout for the DSA tags. The destination ports field is
different for Seville VSC9953 for example. So the choices are to either
duplicate tag_ocelot.c into a new tag_seville.c (sub-optimal) or somehow
take into account a supposed ocelot->dest_ports_offset when packing this
field into the DSA injection header (again not ideal).
Secondly, tag_ocelot.c already needs to memset a 128-bit area to zero
and call some packing() functions of dubious performance in the
fastpath. And most of the values it needs to pack are pretty much
constant (BYPASS=1, SRC_PORT=CPU, DEST=port index). So it would be good
if we could improve that.
The proposed solution is to allocate a memory area per port at probe
time, initialize that with the statically defined bits as per chip
hardware revision, and just perform a simpler memcpy in the fastpath.
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:03 +0000 (19:57 +0300)]
net: mscc: ocelot: convert QSYS_SWITCH_PORT_MODE and SYS_PORT_MODE to regfields
Currently Felix and Ocelot share the same bit layout in these per-port
registers, but Seville does not. So we need reg_fields for that.
Actually since these are per-port registers, we need to also specify the
number of ports, and register size per port, and use the regmap API for
multiple ports.
There's a more subtle point to be made about the other 2 register
fields:
- QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG
- QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE
which we are not writing any longer, for 2 reasons:
- Using the previous API (ocelot_write_rix), we were only writing 1 for
Felix and Ocelot, which was their hardware-default value, and which
there wasn't any intention in changing.
- In the case of SCH_NEXT_CFG, in fact Seville does not have this
register field at all, and therefore, if we want to have common code
we would be required to not write to it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Kochetkov [Mon, 13 Jul 2020 16:57:02 +0000 (19:57 +0300)]
soc: mscc: ocelot: add MII registers description
Add the register definitions for the MSCC MIIM MDIO controller in
preparation for seville_vsc9959.c to create its accessors for the
internal MDIO bus.
Since we've introduced elements to ocelot_regfields that are not
instantiated by felix and ocelot, we need to define the size of the
regfields arrays explicitly, otherwise ocelot_regfields_init, which
iterates up to REGFIELD_MAX, will fault on the undefined regfield
entries (if we're lucky).
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:01 +0000 (19:57 +0300)]
net: mscc: ocelot: convert port registers to regmap
At the moment, there are some minimal register differences between
VSC7514 Ocelot and VSC9959 Felix. To be precise, the PCS1G registers are
missing from Felix because it was integrated with an NXP PCS.
But with VSC9953 Seville (not yet introduced), the register differences
are more pronounced. The MAC registers are located at different offsets
within the DEV_GMII target. So we need to refactor the driver to keep a
regmap even for per-port registers. The callers of the ocelot_port_readl
and ocelot_port_writel were kept unchanged, only the implementation is
now more generic.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 13 Jul 2020 15:20:14 +0000 (18:20 +0300)]
devlink: Fix use-after-free when destroying health reporters
Dereferencing the reporter after it was destroyed in order to unlock the
reporters lock results in a use-after-free [1].
Fix this by storing a pointer to the lock in a local variable before
destroying the reporter.
[1]
==================================================================
BUG: KASAN: use-after-free in devlink_health_reporter_destroy+0x15c/0x1b0 net/core/devlink.c:5476
Read of size 8 at addr
ffff8880650fd020 by task syz-executor.1/904
CPU: 0 PID: 904 Comm: syz-executor.1 Not tainted 5.8.0-rc2+ #35
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xf6/0x16e lib/dump_stack.c:118
print_address_description.constprop.0+0x1c/0x250 mm/kasan/report.c:383
__kasan_report mm/kasan/report.c:513 [inline]
kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530
devlink_health_reporter_destroy+0x15c/0x1b0 net/core/devlink.c:5476
nsim_dev_health_exit+0x8b/0xe0 drivers/net/netdevsim/health.c:317
nsim_dev_reload_destroy+0x7f/0x110 drivers/net/netdevsim/dev.c:1134
nsim_dev_reload_down+0x6e/0xd0 drivers/net/netdevsim/dev.c:712
devlink_reload+0xc6/0x3b0 net/core/devlink.c:2952
devlink_nl_cmd_reload+0x2f1/0x7c0 net/core/devlink.c:2987
genl_family_rcv_msg_doit net/netlink/genetlink.c:691 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:736 [inline]
genl_rcv_msg+0x611/0x9d0 net/netlink/genetlink.c:753
netlink_rcv_skb+0x152/0x440 net/netlink/af_netlink.c:2469
genl_rcv+0x24/0x40 net/netlink/genetlink.c:764
netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline]
netlink_unicast+0x53a/0x750 net/netlink/af_netlink.c:1329
netlink_sendmsg+0x850/0xd90 net/netlink/af_netlink.c:1918
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0x150/0x190 net/socket.c:672
____sys_sendmsg+0x6d8/0x840 net/socket.c:2363
___sys_sendmsg+0xff/0x170 net/socket.c:2417
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2450
do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:359
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x4748ad
Code: Bad RIP value.
RSP: 002b:
00007fd0358adc38 EFLAGS:
00000246 ORIG_RAX:
000000000000002e
RAX:
ffffffffffffffda RBX:
000000000056bf00 RCX:
00000000004748ad
RDX:
0000000000000000 RSI:
00000000200000c0 RDI:
0000000000000003
RBP:
00000000ffffffff R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000246 R12:
0000000000000000
R13:
00000000004d1a4b R14:
00007fd0358ae6b4 R15:
00007fd0358add80
Allocated by task 539:
save_stack+0x1b/0x40 mm/kasan/common.c:48
set_track mm/kasan/common.c:56 [inline]
__kasan_kmalloc mm/kasan/common.c:494 [inline]
__kasan_kmalloc.constprop.0+0xc2/0xd0 mm/kasan/common.c:467
kmalloc include/linux/slab.h:555 [inline]
kzalloc include/linux/slab.h:669 [inline]
__devlink_health_reporter_create+0x91/0x2f0 net/core/devlink.c:5359
devlink_health_reporter_create+0xa1/0x170 net/core/devlink.c:5431
nsim_dev_health_init+0x95/0x3a0 drivers/net/netdevsim/health.c:279
nsim_dev_probe+0xb1e/0xeb0 drivers/net/netdevsim/dev.c:1086
really_probe+0x287/0x6d0 drivers/base/dd.c:525
driver_probe_device+0xfe/0x1d0 drivers/base/dd.c:701
__device_attach_driver+0x21e/0x290 drivers/base/dd.c:807
bus_for_each_drv+0x161/0x1e0 drivers/base/bus.c:431
__device_attach+0x21a/0x360 drivers/base/dd.c:873
bus_probe_device+0x1e6/0x290 drivers/base/bus.c:491
device_add+0xaf2/0x1b00 drivers/base/core.c:2680
nsim_bus_dev_new drivers/net/netdevsim/bus.c:336 [inline]
new_device_store+0x374/0x590 drivers/net/netdevsim/bus.c:215
bus_attr_store+0x75/0xa0 drivers/base/bus.c:122
sysfs_kf_write+0x113/0x170 fs/sysfs/file.c:138
kernfs_fop_write+0x25d/0x480 fs/kernfs/file.c:315
__vfs_write+0x7c/0x100 fs/read_write.c:495
vfs_write+0x265/0x5e0 fs/read_write.c:559
ksys_write+0x12d/0x250 fs/read_write.c:612
do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:359
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Freed by task 904:
save_stack+0x1b/0x40 mm/kasan/common.c:48
set_track mm/kasan/common.c:56 [inline]
kasan_set_free_info mm/kasan/common.c:316 [inline]
__kasan_slab_free+0x12c/0x170 mm/kasan/common.c:455
slab_free_hook mm/slub.c:1474 [inline]
slab_free_freelist_hook mm/slub.c:1507 [inline]
slab_free mm/slub.c:3072 [inline]
kfree+0xe6/0x320 mm/slub.c:4063
devlink_health_reporter_free net/core/devlink.c:5449 [inline]
devlink_health_reporter_put+0xb7/0xf0 net/core/devlink.c:5456
__devlink_health_reporter_destroy net/core/devlink.c:5463 [inline]
devlink_health_reporter_destroy+0x11b/0x1b0 net/core/devlink.c:5475
nsim_dev_health_exit+0x8b/0xe0 drivers/net/netdevsim/health.c:317
nsim_dev_reload_destroy+0x7f/0x110 drivers/net/netdevsim/dev.c:1134
nsim_dev_reload_down+0x6e/0xd0 drivers/net/netdevsim/dev.c:712
devlink_reload+0xc6/0x3b0 net/core/devlink.c:2952
devlink_nl_cmd_reload+0x2f1/0x7c0 net/core/devlink.c:2987
genl_family_rcv_msg_doit net/netlink/genetlink.c:691 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:736 [inline]
genl_rcv_msg+0x611/0x9d0 net/netlink/genetlink.c:753
netlink_rcv_skb+0x152/0x440 net/netlink/af_netlink.c:2469
genl_rcv+0x24/0x40 net/netlink/genetlink.c:764
netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline]
netlink_unicast+0x53a/0x750 net/netlink/af_netlink.c:1329
netlink_sendmsg+0x850/0xd90 net/netlink/af_netlink.c:1918
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0x150/0x190 net/socket.c:672
____sys_sendmsg+0x6d8/0x840 net/socket.c:2363
___sys_sendmsg+0xff/0x170 net/socket.c:2417
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2450
do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:359
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The buggy address belongs to the object at
ffff8880650fd000
which belongs to the cache kmalloc-512 of size 512
The buggy address is located 32 bytes inside of
512-byte region [
ffff8880650fd000,
ffff8880650fd200)
The buggy address belongs to the page:
page:
ffffea0001943f00 refcount:1 mapcount:0 mapping:
0000000000000000 index:0xffff8880650ff800 head:
ffffea0001943f00 order:2 compound_mapcount:0 compound_pincount:0
flags: 0x100000000010200(slab|head)
raw:
0100000000010200 ffffea0001a06a08 ffffea00010ad308 ffff88806c402500
raw:
ffff8880650ff800 0000000000100009 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8880650fcf00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8880650fcf80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>
ffff8880650fd000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8880650fd080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8880650fd100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Fixes:
3c5584bf0a04 ("devlink: Rework devlink health reporter destructor")
Fixes:
15c724b997a8 ("devlink: Add devlink health port reporters API")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bartosz Golaszewski [Mon, 13 Jul 2020 15:12:07 +0000 (17:12 +0200)]
net: phy: fix mdio-mscc-miim build
PHYLIB is not selected by mdio-mscc-miim but it uses mdio devres helpers.
Explicitly select MDIO_DEVRES in this driver's Kconfig entry.
Reported-by: kernel test robot <lkp@intel.com>
Fixes:
1814cff26739 ("net: phy: add a Kconfig option for mdio_devres")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander A. Klimov [Mon, 13 Jul 2020 14:30:54 +0000 (16:30 +0200)]
isdn/capi: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 13 Jul 2020 14:23:44 +0000 (22:23 +0800)]
net: make symbol 'flush_works' static
The sparse tool complains as follows:
net/core/dev.c:5594:1: warning:
symbol '__pcpu_scope_flush_works' was not declared. Should it be static?
'flush_works' is not used outside of dev.c, so marks
it static.
Fixes:
41852497a9205 ("net: batch calls to flush_all_backlogs()")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 14 Jul 2020 00:22:22 +0000 (17:22 -0700)]
Merge branch 'mlxsw-Add-support-for-buffer-drops-mirroring'
Petr Machata says:
====================
mlxsw: Add support for buffer drops mirroring
This set offloads the recently introduced qevent infrastructure in TC and
allows mlxsw to support mirroring of packets that were dropped due to
buffer related reasons (e.g., early drops) during forwarding.
Up until now mlxsw only supported mirroring that was either triggered by
per-port triggers (i.e., via matchall) or by the policy engine (i.e.,
via flower). Packets that are dropped due to buffer related reasons are
mirrored using a third type of trigger, a global trigger.
Global triggers are bound once to a mirroring (SPAN) agent and enabled
on a per-{port, TC} basis. This allows users, for example, to request
that only packets that were early dropped on a specific netdev to be
mirrored.
Patch set overview:
Patch #1 extends flow_block_offload and indirect offload structure to pass
a scheduler instead of a netdevice. That is necessary, because binding type
and netdevice are not a unique identifier of the block anymore.
Patches #2-#3 add the required registers to support above mentioned
functionality.
Patches #4-#6 gradually add support for global mirroring triggers.
Patch #7 adds support for enablement of global mirroring triggers.
Patches #8-#11 are cleanups in the flow offload code and shuffle some
code around to make the qevent offload easier.
Patch #12 implements offload of RED early_drop qevent.
Patch #13 extends the RED selftest for offloaded datapath to cover
early_drop qevent.
v2:
- Patch #1:
- In struct flow_block_indr, track both sch and dev.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Fri, 10 Jul 2020 21:55:15 +0000 (00:55 +0300)]
selftests: mlxsw: RED: Test offload of mirror on RED early_drop qevent
Add a selftest for offloading a mirror action attached to the block
associated with RED early_drop qevent.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Fri, 10 Jul 2020 21:55:14 +0000 (00:55 +0300)]
mlxsw: spectrum_qdisc: Offload mirroring on RED qevent early_drop
The RED qevents early_drop and mark can be offloaded under the following
fairly strict conditions:
- At most one filter is configured at the qevent block
- The protocol is "any"
- The classifier is matchall
- The action is trap, sample, or mirror with the same conditions as
with other SPAN offloads
- The hw_counters type is none
In this patchset, implement offload of mirror for early_drop qevent.
The ECN trigger is currently not implemented in the FW and therefore
the mark qevent is not supported.
The qevent notifications look exactly like regular block binding
notifications with a binder type that identifies them as qevents.
Therefore the details of processing this binding are fairly similar
to the matchall offload.
struct flow_block_offload.sch points at the qdisc in question. Use it to
figure out if the qdisc is offloaded at all and what TC it configures.
Bounce bindings on not-offloaded qdiscs.
Individual bindings are kept in a list so that several qevents can share
the same block and all binding points get configured as the configured
filters change.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Fri, 10 Jul 2020 21:55:13 +0000 (00:55 +0300)]
mlxsw: spectrum_flow: Promote binder-type dispatch to spectrum.c
Two RED qevents have been introduced recently. From the point of view of a
driver, qevents are simply blocks with unusual binder types. However they
need to be handled by different logic than ACL-like flows.
Thus rename mlxsw_sp_setup_tc_block() to mlxsw_sp_setup_tc_block_clsact()
and move the binder-type dispatch from there to spectrum.c into a new
function of the original name. The new dispatcher is easier to extend with
new binder types.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Fri, 10 Jul 2020 21:55:12 +0000 (00:55 +0300)]
mlxsw: spectrum_matchall: Publish matchall data structures
A following patch introduces offloading of filters attached to blocks bound
to the RED tail_drop qevent. The only classifier that mlxsw will permit in
this role is matchall. mlxsw currently offloads matchall filters used with
clsact qdisc. The data structures used for that offload will come handy for
the qevent offload as well. Publish them in spectrum.h.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Fri, 10 Jul 2020 21:55:11 +0000 (00:55 +0300)]
mlxsw: spectrum_flow: Drop an unused field
The field "dev" in struct mlxsw_sp_flow_block_binding is not used. Drop it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Fri, 10 Jul 2020 21:55:10 +0000 (00:55 +0300)]
mlxsw: spectrum_flow: Convert a goto to a return
No clean-up is performed at the target label of this goto. Convert it to a
direct return.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 10 Jul 2020 21:55:09 +0000 (00:55 +0300)]
mlxsw: spectrum_span: Add APIs to enable / disable global mirroring triggers
While the binding of global mirroring triggers to a SPAN agent is
global, packets are only mirrored if they belong to a port and TC on
which the trigger was enabled. This allows, for example, to mirror
packets that were tail-dropped on a specific netdev.
Implement the operations that allow to enable / disable a global
mirroring trigger on a specific port and TC.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 10 Jul 2020 21:55:08 +0000 (00:55 +0300)]
mlxsw: spectrum_span: Add support for global mirroring triggers
Global mirroring triggers are triggers that are only keyed by their
trigger, as opposed to per-port triggers, which are keyed by their
trigger and port.
Such triggers allow mirroring packets that were tail/early dropped or
ECN marked to a SPAN agent.
Implement the previously added trigger operations for these global
triggers. Since such triggers are only supported from Spectrum-2
onwards, have the Spectrum-1 operations return an error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 10 Jul 2020 21:55:07 +0000 (00:55 +0300)]
mlxsw: spectrum_span: Prepare for global mirroring triggers
Currently, a SPAN agent can only be bound to a per-port trigger where
the trigger is either an incoming packet (INGRESS) or an outgoing packet
(EGRESS) to / from the port.
The subsequent patch will introduce the concept of global mirroring
triggers. The binding / unbinding of global triggers is different than
that of per-port triggers. Such triggers also need to be enabled /
disabled on a per-{port, TC} basis and are only supported from
Spectrum-2 onwards.
Add trigger operations that allow us to abstract these differences. Only
implement the operations for per-port triggers. Next patch will
implement the operations for global triggers.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 10 Jul 2020 21:55:06 +0000 (00:55 +0300)]
mlxsw: spectrum_span: Move SPAN operations out of global file
The per-ASIC SPAN operations are relevant to the SPAN module and
therefore should be implemented there and not in the main driver file.
Move them.
These operations will be extended later on.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Fri, 10 Jul 2020 21:55:05 +0000 (00:55 +0300)]
mlxsw: reg: Add Monitoring Port Analyzer Global Register
This register is used for global port analyzer configurations.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Fri, 10 Jul 2020 21:55:04 +0000 (00:55 +0300)]
mlxsw: reg: Add Monitoring Mirror Trigger Enable Register
This register is used to configure the mirror enable for different
mirror reasons.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Fri, 10 Jul 2020 21:55:03 +0000 (00:55 +0300)]
net: sched: Pass qdisc reference in struct flow_block_offload
Previously, shared blocks were only relevant for the pseudo-qdiscs ingress
and clsact. Recently, a qevent facility was introduced, which allows to
bind blocks to well-defined slots of a qdisc instance. RED in particular
got two qevents: early_drop and mark. Drivers that wish to offload these
blocks will be sent the usual notification, and need to know which qdisc it
is related to.
To that end, extend flow_block_offload with a "sch" pointer, and initialize
as appropriate. This prompts changes in the indirect block facility, which
now tracks the scheduler in addition to the netdevice. Update signatures of
several functions similarly.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 14 Jul 2020 00:20:40 +0000 (17:20 -0700)]
Merge branch 'net-simple-kerneldoc-fixes'
Andrew Lunn says:
====================
net simple kerneldoc fixes
This is a collection of simple kerneldoc fixes. They are all low
hanging fruit, were not real understanding of the code was needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:16 +0000 (01:15 +0200)]
net: x25: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:15 +0000 (01:15 +0200)]
net: wireless: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:14 +0000 (01:15 +0200)]
net: tipc: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Jon Maloy <jmaloy@redhat.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:13 +0000 (01:15 +0200)]
net: switchdev: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:12 +0000 (01:15 +0200)]
net: socket: Move kerneldoc next to function it documents
Fix the warning "Function parameter or member 'inode' not described in
'__sock_release'' due to the kerneldoc being placed before
__sock_release() not sock_release(), which does not take an inode
parameter.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:11 +0000 (01:15 +0200)]
net: sched: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:10 +0000 (01:15 +0200)]
net: rxrpc: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:09 +0000 (01:15 +0200)]
net: openvswitch: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:08 +0000 (01:15 +0200)]
net: nfc: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:07 +0000 (01:15 +0200)]
net: netlabel: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Paul Moore <paul@paul-moore.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:06 +0000 (01:15 +0200)]
net: netfilter: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Jozsef Kadlecsik <kadlec@netfilter.org>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:05 +0000 (01:15 +0200)]
net: mac80211: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:04 +0000 (01:15 +0200)]
net: llc: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:03 +0000 (01:15 +0200)]
net: ipv6: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:02 +0000 (01:15 +0200)]
net: ipv4: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Paul Moore <paul@paul-moore.com>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:01 +0000 (01:15 +0200)]
net: decnet: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:00 +0000 (01:15 +0200)]
net: dccp: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:14:59 +0000 (01:14 +0200)]
net: core: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:14:58 +0000 (01:14 +0200)]
net: can: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:14:57 +0000 (01:14 +0200)]
net: 9p: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Cc: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Mon, 13 Jul 2020 12:24:18 +0000 (07:24 -0500)]
net: ipa: fix kerneldoc comments
This commit affects comments (and in one case, whitespace) only.
Throughout the IPA code, return statements are documented using
"@Return:", whereas they should use "Return:" instead. Fix these
mistakes.
In function definitions, some parameters are missing their comment
to describe them. And in structure definitions, some fields are
missing their comment to describe them. Add these missing
descriptions.
Some arguments changed name and type along the way, but their
descriptions were not updated (an endpoint pointer is now used in
many places that previously used an endpoint ID). Fix these
incorrect parameter descriptions.
In the description for the ipa_clock structure, one field had a
semicolon instead of a colon in its description. Fix this.
Add a missing function description for ipa_gsi_endpoint_data_empty().
All of these issues were identified when building with "W=1".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov [Tue, 14 Jul 2020 00:07:43 +0000 (17:07 -0700)]
Merge branch 'strip-mods-from-global-vars'
Andrii Nakryiko says:
====================
Fix bpftool logic of stripping away const/volatile modifiers for all global
variables during BPF skeleton generation. See patch #1 for details on when
existing logic breaks and why it's important. Support special .strip_mods=true
mode in btf_dump__emit_type_decl.
Recent example of when this has caused problems can be found in [0].
[0] https://github.com/iovisor/bcc/pull/2994#issuecomment-
650588533
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Andrii Nakryiko [Mon, 13 Jul 2020 23:24:09 +0000 (16:24 -0700)]
tools/bpftool: Strip away modifiers from global variables
Reliably remove all the type modifiers from read-only (.rodata) global
variable definitions, including cases of inner field const modifiers and
arrays of const values.
Also modify one of selftests to ensure that const volatile struct doesn't
prevent user-space from modifying .rodata variable.
Fixes:
985ead416df3 ("bpftool: Add skeleton codegen command")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200713232409.3062144-3-andriin@fb.com
Andrii Nakryiko [Mon, 13 Jul 2020 23:24:08 +0000 (16:24 -0700)]
libbpf: Support stripping modifiers for btf_dump
One important use case when emitting const/volatile/restrict is undesirable is
BPF skeleton generation of DATASEC layout. These are further memory-mapped and
can be written/read from user-space directly.
For important case of .rodata variables, bpftool strips away first-level
modifiers, to make their use on user-space side simple and not requiring extra
type casts to override compiler complaining about writing to const variables.
This logic works mostly fine, but breaks in some more complicated cases. E.g.:
const volatile int params[10];
Because in BTF it's a chain of ARRAY -> CONST -> VOLATILE -> INT, bpftool
stops at ARRAY and doesn't strip CONST and VOLATILE. In skeleton this variable
will be emitted as is. So when used from user-space, compiler will complain
about writing to const array. This is problematic, as also mentioned in [0].
To solve this for arrays and other non-trivial cases (e.g., inner
const/volatile fields inside the struct), teach btf_dump to strip away any
modifier, when requested. This is done as an extra option on
btf_dump__emit_type_decl() API.
Reported-by: Anton Protopopov <a.s.protopopov@gmail.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200713232409.3062144-2-andriin@fb.com
Alexander A. Klimov [Mon, 13 Jul 2020 10:24:18 +0000 (12:24 +0200)]
atm: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov [Mon, 13 Jul 2020 23:55:49 +0000 (16:55 -0700)]
Merge branch 'trace_printk-banner-remove'
Alan Maguire says:
====================
Steven suggested a way to resolve the appearance of the warning banner
that appears as a result of using trace_printk() in BPF [1].
Applying the patch and testing reveals all works as expected; we
can call bpf_trace_printk() and see the trace messages in
/sys/kernel/debug/tracing/trace_pipe and no banner message appears.
Also add a test prog to verify basic bpf_trace_printk() helper behaviour.
Changes since v2:
- fixed stray newline in bpf_trace_printk(), use sizeof(buf)
rather than #defined value in vsnprintf() (Daniel, patch 1)
- Daniel also pointed out that vsnprintf() returns 0 on error rather
than a negative value; also turns out that a null byte is not
appended if the length of the string written is zero, so to fix
for cases where the string to be traced is zero length we set the
null byte explicitly (Daniel, patch 1)
- switch to using getline() for retrieving lines from trace buffer
to ensure we don't read a portion of the search message in one
read() operation and then fail to find it (Andrii, patch 2)
Changes since v1:
- reorder header inclusion in bpf_trace.c (Steven, patch 1)
- trace zero-length messages also (Andrii, patch 1)
- use a raw spinlock to ensure there are no issues for PREMMPT_RT
kernels when using bpf_trace_printk() within other raw spinlocks
(Steven, patch 1)
- always enable bpf_trace_printk() tracepoint when loading programs
using bpf_trace_printk() as this will ensure that a user disabling
that tracepoint will not prevent tracing output from being logged
(Steven, patch 1)
- use "tp/raw_syscalls/sys_enter" and a usleep(1) to trigger events
in the selftest ensuring test runs faster (Andrii, patch 2)
[1] https://lore.kernel.org/r/
20200628194334.
6238b933@oasis.local.home
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Alexander A. Klimov [Mon, 13 Jul 2020 09:33:23 +0000 (11:33 +0200)]
WAN: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Maguire [Mon, 13 Jul 2020 11:52:34 +0000 (12:52 +0100)]
selftests/bpf: Add selftests verifying bpf_trace_printk() behaviour
Simple selftests that verifies bpf_trace_printk() returns a sensible
value and tracing messages appear.
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/1594641154-18897-3-git-send-email-alan.maguire@oracle.com
Alan Maguire [Mon, 13 Jul 2020 11:52:33 +0000 (12:52 +0100)]
bpf: Use dedicated bpf_trace_printk event instead of trace_printk()
The bpf helper bpf_trace_printk() uses trace_printk() under the hood.
This leads to an alarming warning message originating from trace
buffer allocation which occurs the first time a program using
bpf_trace_printk() is loaded.
We can instead create a trace event for bpf_trace_printk() and enable
it in-kernel when/if we encounter a program using the
bpf_trace_printk() helper. With this approach, trace_printk()
is not used directly and no warning message appears.
This work was started by Steven (see Link) and finished by Alan; added
Steven's Signed-off-by with his permission.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/r/20200628194334.6238b933@oasis.local.home
Link: https://lore.kernel.org/bpf/1594641154-18897-2-git-send-email-alan.maguire@oracle.com
Andrii Nakryiko [Fri, 10 Jul 2020 23:26:04 +0000 (16:26 -0700)]
tools/bpftool: Remove warning about PID iterator support
Don't emit warning that bpftool was built without PID iterator support. This
error garbles JSON output of otherwise perfectly valid show commands.
Reported-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200710232605.20918-1-andriin@fb.com
Alexei Starovoitov [Mon, 13 Jul 2020 22:32:56 +0000 (15:32 -0700)]
Merge branch 'af_xdp-stats'
Ciara Loftus says:
====================
This series introduces new statistics for af_xdp:
1. drops due to rx ring being full
2. drops due to fill ring being empty
3. failures pulling an item from the tx ring
These statistics should assist users debugging and troubleshooting
peformance issues and packet drops.
The statistics are made available though the getsockopt and xsk_diag
interfaces, and the ability to dump these extended statistics is made
available in the xdpsock application via the --extra-stats or -x flag.
A separate patch which will add ss/iproute2 support will follow.
====================
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Ciara Loftus [Wed, 8 Jul 2020 07:28:35 +0000 (07:28 +0000)]
xsk: Add xdp statistics to xsk_diag
Add xdp statistics to the information dumped through the xsk_diag interface
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200708072835.4427-4-ciara.loftus@intel.com
Ciara Loftus [Wed, 8 Jul 2020 07:28:34 +0000 (07:28 +0000)]
samples: bpf: Add an option for printing extra statistics in xdpsock
Introduce the --extra-stats (or simply -x) flag to the xdpsock application
which prints additional statistics alongside the regular rx and tx
counters. The new statistics printed report error conditions eg. rx ring
full, invalid descriptors, etc.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200708072835.4427-3-ciara.loftus@intel.com
Ciara Loftus [Wed, 8 Jul 2020 07:28:33 +0000 (07:28 +0000)]
xsk: Add new statistics
It can be useful for the user to know the reason behind a dropped packet.
Introduce new counters which track drops on the receive path caused by:
1. rx ring being full
2. fill ring being empty
Also, on the tx path introduce a counter which tracks the number of times
we attempt pull from the tx ring when it is empty.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200708072835.4427-2-ciara.loftus@intel.com
Alexei Starovoitov [Mon, 13 Jul 2020 17:42:03 +0000 (10:42 -0700)]
Merge branch 'resolve_btfids'
Jiri Olsa says:
====================
This patchset adds:
- support to generate BTF ID lists that are resolved during
kernel linking and usable within kernel code with following
macros:
BTF_ID_LIST(bpf_skb_output_btf_ids)
BTF_ID(struct, sk_buff)
and access it in kernel code via:
extern u32 bpf_skb_output_btf_ids[];
- resolve_btfids tool that scans elf object for .BTF_ids
section and resolves its symbols with BTF ID values
- resolving of bpf_ctx_convert struct and several other
objects with BTF_ID_LIST
v7 changes:
- added more acks [Andrii]
- added some name-conflicting entries and fixed resolve_btfids
to process them properly [Andrii]
- changed bpf_get_task_stack_proto to use BTF_IDS_LIST/BTF_ID
macros [Andrii]
- fixed selftest build for resolve_btfids test
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Alexander A. Klimov [Mon, 13 Jul 2020 09:02:51 +0000 (11:02 +0200)]
AX.25 Kconfig: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander A. Klimov [Mon, 13 Jul 2020 07:51:08 +0000 (09:51 +0200)]
dccp: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tetsuo Handa [Mon, 13 Jul 2020 04:53:30 +0000 (13:53 +0900)]
net: fddi: skfp: Remove addr_to_string().
kbuild test robot found that addr_to_string() is available only when
DEBUG is defined. And I found that what that function is doing is
what %pM will do. Thus, replace %s with %pM and remove thread-unsafe
addr_to_string() function.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>