OSDN Git Service
Jiri Pirko [Thu, 25 Apr 2019 13:59:45 +0000 (15:59 +0200)]
netdevsim: move device registration and related code to bus.c
Move netdevsim device registration into bus.c and alongside with that
the related sysfs attributes. Introduce new struct nsim_bus_dev to
represent a netdevsim device on netdevsim bus.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 25 Apr 2019 13:59:44 +0000 (15:59 +0200)]
netdevsim: put netdevsim bus code into separate file
As the code related to netdevsim bus is going to get bigger, move the
existing code to a separate file.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 25 Apr 2019 13:59:43 +0000 (15:59 +0200)]
netdevsim: rename devlink.c to dev.c to contain per-dev(asic) items
The existing devlink.c code is going to be extended to represent asic
device on a bus. As this is about more than just devlink,
rename the file. Do appropriate prefix renaming alongside with that.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 25 Apr 2019 13:59:42 +0000 (15:59 +0200)]
netdevsim: create devlink instance per netdevsim instance
Currently there is one devlink instance created per network namespace.
That is quite odd considering the fact that devlink instance should
represent an ASIC. The following patches are going to move the devlink
instance even more down to a bus device, but until then, have one
devlink instance per netdevsim instance. Struct nsim_devlink is
introduced to hold fib setting.
The changes in the fib code are only related to holding the
configuration per devlink instance instead of network namespace.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 25 Apr 2019 13:59:41 +0000 (15:59 +0200)]
netdevsim: move device registration on bus to be done earlier in init
As a dependency of the subsequent patch, mode device registration to be
done earlier, directly in nsim_newlink().
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 26 Apr 2019 05:39:38 +0000 (01:39 -0400)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-04-25
Here's the main bluetooth-next pull request for the 5.2 kernel.
- Added support for Mediatek SDIO controllers
- Added support for Broadcom BCM2076B1 UART controller
- Added support for Marvel SD8987 chipset
- Fix buffer overflow bug in hidp protocol
- Various other smaller fixes & improvements
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 26 Apr 2019 03:52:29 +0000 (23:52 -0400)]
Merge git://git./linux/kernel/git/davem/net
Two easy cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel Holtmann [Wed, 24 Apr 2019 20:19:17 +0000 (22:19 +0200)]
Bluetooth: Align minimum encryption key size for LE and BR/EDR connections
The minimum encryption key size for LE connections is 56 bits and to
align LE with BR/EDR, enforce 56 bits of minimum encryption key size for
BR/EDR connections as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Linus Torvalds [Wed, 24 Apr 2019 23:18:59 +0000 (16:18 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"Just the usual assortment of small'ish fixes:
1) Conntrack timeout is sometimes not initialized properly, from
Alexander Potapenko.
2) Add a reasonable range limit to tcp_min_rtt_wlen to avoid
undefined behavior. From ZhangXiaoxu.
3) des1 field of descriptor in stmmac driver is initialized with the
wrong variable. From Yue Haibing.
4) Increase mlxsw pci sw reset timeout a little bit more, from Ido
Schimmel.
5) Match IOT2000 stmmac devices more accurately, from Su Bao Cheng.
6) Fallback refcount fix in TLS code, from Jakub Kicinski.
7) Fix max MTU check when using XDP in mlx5, from Maxim Mikityanskiy.
8) Fix recursive locking in team driver, from Hangbin Liu.
9) Fix tls_set_device_offload_Rx() deadlock, from Jakub Kicinski.
10) Don't use napi_alloc_frag() outside of softiq context of socionext
driver, from Ilias Apalodimas.
11) MAC address increment overflow in ncsi, from Tao Ren.
12) Fix a regression in 8K/1M pool switching of RDS, from Zhu Yanjun.
13) ipv4_link_failure has to validate the headers that are actually
there because RAW sockets can pass in arbitrary garbage, from Eric
Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
ipv4: add sanity checks in ipv4_link_failure()
net/rose: fix unbound loop in rose_loopback_timer()
rxrpc: fix race condition in rxrpc_input_packet()
net: rds: exchange of 8K and 1M pool
net: vrf: Fix operation not supported when set vrf mac
net/ncsi: handle overflow when incrementing mac address
net: socionext: replace napi_alloc_frag with the netdev variant on init
net: atheros: fix spelling mistake "underun" -> "underrun"
spi: ST ST95HF NFC: declare missing of table
spi: Micrel eth switch: declare missing of table
net: stmmac: move stmmac_check_ether_addr() to driver probe
netfilter: fix nf_l4proto_log_invalid to log invalid packets
netfilter: never get/set skb->tstamp
netfilter: ebtables: CONFIG_COMPAT: drop a bogus WARN_ON
Documentation: decnet: remove reference to CONFIG_DECNET_ROUTE_FWMARK
dt-bindings: add an explanation for internal phy-mode
net/tls: don't leak IV and record seq when offload fails
net/tls: avoid potential deadlock in tls_set_device_offload_rx()
selftests/net: correct the return value for run_afpackettests
team: fix possible recursive locking when add slaves
...
Linus Torvalds [Wed, 24 Apr 2019 23:15:38 +0000 (16:15 -0700)]
Merge tag 'leds-for-5.1-rc7' of git://git./linux/kernel/git/j.anaszewski/linux-leds
Pull LED update from Jacek Anaszewski:
"A single change to MAINTAINERS:
We announce a new LED reviewer - Dan Murphy"
* tag 'leds-for-5.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
MAINTAINERS: LEDs: Add designated reviewer for LED subsystem
Eric Dumazet [Wed, 24 Apr 2019 15:04:05 +0000 (08:04 -0700)]
ipv4: add sanity checks in ipv4_link_failure()
Before calling __ip_options_compile(), we need to ensure the network
header is a an IPv4 one, and that it is already pulled in skb->head.
RAW sockets going through a tunnel can end up calling ipv4_link_failure()
with total garbage in the skb, or arbitrary lengthes.
syzbot report :
BUG: KASAN: stack-out-of-bounds in memcpy include/linux/string.h:355 [inline]
BUG: KASAN: stack-out-of-bounds in __ip_options_echo+0x294/0x1120 net/ipv4/ip_options.c:123
Write of size 69 at addr
ffff888096abf068 by task syz-executor.4/9204
CPU: 0 PID: 9204 Comm: syz-executor.4 Not tainted 5.1.0-rc5+ #77
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
check_memory_region_inline mm/kasan/generic.c:185 [inline]
check_memory_region+0x123/0x190 mm/kasan/generic.c:191
memcpy+0x38/0x50 mm/kasan/common.c:133
memcpy include/linux/string.h:355 [inline]
__ip_options_echo+0x294/0x1120 net/ipv4/ip_options.c:123
__icmp_send+0x725/0x1400 net/ipv4/icmp.c:695
ipv4_link_failure+0x29f/0x550 net/ipv4/route.c:1204
dst_link_failure include/net/dst.h:427 [inline]
vti6_xmit net/ipv6/ip6_vti.c:514 [inline]
vti6_tnl_xmit+0x10d4/0x1c0c net/ipv6/ip6_vti.c:553
__netdev_start_xmit include/linux/netdevice.h:4414 [inline]
netdev_start_xmit include/linux/netdevice.h:4423 [inline]
xmit_one net/core/dev.c:3292 [inline]
dev_hard_start_xmit+0x1b2/0x980 net/core/dev.c:3308
__dev_queue_xmit+0x271d/0x3060 net/core/dev.c:3878
dev_queue_xmit+0x18/0x20 net/core/dev.c:3911
neigh_direct_output+0x16/0x20 net/core/neighbour.c:1527
neigh_output include/net/neighbour.h:508 [inline]
ip_finish_output2+0x949/0x1740 net/ipv4/ip_output.c:229
ip_finish_output+0x73c/0xd50 net/ipv4/ip_output.c:317
NF_HOOK_COND include/linux/netfilter.h:278 [inline]
ip_output+0x21f/0x670 net/ipv4/ip_output.c:405
dst_output include/net/dst.h:444 [inline]
NF_HOOK include/linux/netfilter.h:289 [inline]
raw_send_hdrinc net/ipv4/raw.c:432 [inline]
raw_sendmsg+0x1d2b/0x2f20 net/ipv4/raw.c:663
inet_sendmsg+0x147/0x5d0 net/ipv4/af_inet.c:798
sock_sendmsg_nosec net/socket.c:651 [inline]
sock_sendmsg+0xdd/0x130 net/socket.c:661
sock_write_iter+0x27c/0x3e0 net/socket.c:988
call_write_iter include/linux/fs.h:1866 [inline]
new_sync_write+0x4c7/0x760 fs/read_write.c:474
__vfs_write+0xe4/0x110 fs/read_write.c:487
vfs_write+0x20c/0x580 fs/read_write.c:549
ksys_write+0x14f/0x2d0 fs/read_write.c:599
__do_sys_write fs/read_write.c:611 [inline]
__se_sys_write fs/read_write.c:608 [inline]
__x64_sys_write+0x73/0xb0 fs/read_write.c:608
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x458c29
Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007f293b44bc78 EFLAGS:
00000246 ORIG_RAX:
0000000000000001
RAX:
ffffffffffffffda RBX:
0000000000000003 RCX:
0000000000458c29
RDX:
0000000000000014 RSI:
00000000200002c0 RDI:
0000000000000003
RBP:
000000000073bf00 R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000246 R12:
00007f293b44c6d4
R13:
00000000004c8623 R14:
00000000004ded68 R15:
00000000ffffffff
The buggy address belongs to the page:
page:
ffffea00025aafc0 count:0 mapcount:0 mapping:
0000000000000000 index:0x0
flags: 0x1fffc0000000000()
raw:
01fffc0000000000 0000000000000000 ffffffff025a0101 0000000000000000
raw:
0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888096abef80: 00 00 00 f2 f2 f2 f2 f2 00 00 00 00 00 00 00 f2
ffff888096abf000: f2 f2 f2 f2 00 00 00 00 00 00 00 00 00 00 00 00
>
ffff888096abf080: 00 00 f3 f3 f3 f3 00 00 00 00 00 00 00 00 00 00
^
ffff888096abf100: 00 00 00 00 f1 f1 f1 f1 00 00 f3 f3 00 00 00 00
ffff888096abf180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Fixes:
ed0de45a1008 ("ipv4: recompile ip options in ipv4_link_failure")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Suryaputra <ssuryaextr@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 24 Apr 2019 12:35:00 +0000 (05:35 -0700)]
net/rose: fix unbound loop in rose_loopback_timer()
This patch adds a limit on the number of skbs that fuzzers can queue
into loopback_queue. 1000 packets for rose loopback seems more than enough.
Then, since we now have multiple cpus in most linux hosts,
we also need to limit the number of skbs rose_loopback_timer()
can dequeue at each round.
rose_loopback_queue() can be drop-monitor friendly, calling
consume_skb() or kfree_skb() appropriately.
Finally, use mod_timer() instead of del_timer() + add_timer()
syzbot report was :
rcu: INFO: rcu_preempt self-detected stall on CPU
rcu: 0-...!: (10499 ticks this GP) idle=536/1/0x4000000000000002 softirq=103291/103291 fqs=34
rcu: (t=10500 jiffies g=140321 q=323)
rcu: rcu_preempt kthread starved for 10426 jiffies! g140321 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 ->cpu=1
rcu: RCU grace-period kthread stack dump:
rcu_preempt I29168 10 2 0x80000000
Call Trace:
context_switch kernel/sched/core.c:2877 [inline]
__schedule+0x813/0x1cc0 kernel/sched/core.c:3518
schedule+0x92/0x180 kernel/sched/core.c:3562
schedule_timeout+0x4db/0xfd0 kernel/time/timer.c:1803
rcu_gp_fqs_loop kernel/rcu/tree.c:1971 [inline]
rcu_gp_kthread+0x962/0x17b0 kernel/rcu/tree.c:2128
kthread+0x357/0x430 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
NMI backtrace for cpu 0
CPU: 0 PID: 7632 Comm: kworker/0:4 Not tainted 5.1.0-rc5+ #172
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events iterate_cleanup_work
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
nmi_cpu_backtrace.cold+0x63/0xa4 lib/nmi_backtrace.c:101
nmi_trigger_cpumask_backtrace+0x1be/0x236 lib/nmi_backtrace.c:62
arch_trigger_cpumask_backtrace+0x14/0x20 arch/x86/kernel/apic/hw_nmi.c:38
trigger_single_cpu_backtrace include/linux/nmi.h:164 [inline]
rcu_dump_cpu_stacks+0x183/0x1cf kernel/rcu/tree.c:1223
print_cpu_stall kernel/rcu/tree.c:1360 [inline]
check_cpu_stall kernel/rcu/tree.c:1434 [inline]
rcu_pending kernel/rcu/tree.c:3103 [inline]
rcu_sched_clock_irq.cold+0x500/0xa4a kernel/rcu/tree.c:2544
update_process_times+0x32/0x80 kernel/time/timer.c:1635
tick_sched_handle+0xa2/0x190 kernel/time/tick-sched.c:161
tick_sched_timer+0x47/0x130 kernel/time/tick-sched.c:1271
__run_hrtimer kernel/time/hrtimer.c:1389 [inline]
__hrtimer_run_queues+0x33e/0xde0 kernel/time/hrtimer.c:1451
hrtimer_interrupt+0x314/0x770 kernel/time/hrtimer.c:1509
local_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1035 [inline]
smp_apic_timer_interrupt+0x120/0x570 arch/x86/kernel/apic/apic.c:1060
apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:807
RIP: 0010:__sanitizer_cov_trace_pc+0x0/0x50 kernel/kcov.c:95
Code: 89 25 b4 6e ec 08 41 bc f4 ff ff ff e8 cd 5d ea ff 48 c7 05 9e 6e ec 08 00 00 00 00 e9 a4 e9 ff ff 90 90 90 90 90 90 90 90 90 <55> 48 89 e5 48 8b 75 08 65 48 8b 04 25 00 ee 01 00 65 8b 15 c8 60
RSP: 0018:
ffff8880ae807ce0 EFLAGS:
00000286 ORIG_RAX:
ffffffffffffff13
RAX:
ffff88806fd40640 RBX:
dffffc0000000000 RCX:
ffffffff863fbc56
RDX:
0000000000000100 RSI:
ffffffff863fbc1d RDI:
ffff88808cf94228
RBP:
ffff8880ae807d10 R08:
ffff88806fd40640 R09:
ffffed1015d00f8b
R10:
ffffed1015d00f8a R11:
0000000000000003 R12:
ffff88808cf941c0
R13:
00000000fffff034 R14:
ffff8882166cd840 R15:
0000000000000000
rose_loopback_timer+0x30d/0x3f0 net/rose/rose_loopback.c:91
call_timer_fn+0x190/0x720 kernel/time/timer.c:1325
expire_timers kernel/time/timer.c:1362 [inline]
__run_timers kernel/time/timer.c:1681 [inline]
__run_timers kernel/time/timer.c:1649 [inline]
run_timer_softirq+0x652/0x1700 kernel/time/timer.c:1694
__do_softirq+0x266/0x95a kernel/softirq.c:293
do_softirq_own_stack+0x2a/0x40 arch/x86/entry/entry_64.S:1027
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 24 Apr 2019 16:44:11 +0000 (09:44 -0700)]
rxrpc: fix race condition in rxrpc_input_packet()
After commit
5271953cad31 ("rxrpc: Use the UDP encap_rcv hook"),
rxrpc_input_packet() is directly called from lockless UDP receive
path, under rcu_read_lock() protection.
It must therefore use RCU rules :
- udp_sk->sk_user_data can be cleared at any point in this function.
rcu_dereference_sk_user_data() is what we need here.
- Also, since sk_user_data might have been set in rxrpc_open_socket()
we must observe a proper RCU grace period before kfree(local) in
rxrpc_lookup_local()
v4: @local can be NULL in xrpc_lookup_local() as reported by kbuild test robot <lkp@intel.com>
and Julia Lawall <julia.lawall@lip6.fr>, thanks !
v3,v2 : addressed David Howells feedback, thanks !
syzbot reported :
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 19236 Comm: syz-executor703 Not tainted 5.1.0-rc6 #79
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__lock_acquire+0xbef/0x3fb0 kernel/locking/lockdep.c:3573
Code: 00 0f 85 a5 1f 00 00 48 81 c4 10 01 00 00 5b 41 5c 41 5d 41 5e 41 5f 5d c3 48 b8 00 00 00 00 00 fc ff df 4c 89 ea 48 c1 ea 03 <80> 3c 02 00 0f 85 4a 21 00 00 49 81 7d 00 20 54 9c 89 0f 84 cf f4
RSP: 0018:
ffff88809d7aef58 EFLAGS:
00010002
RAX:
dffffc0000000000 RBX:
0000000000000000 RCX:
0000000000000000
RDX:
0000000000000026 RSI:
0000000000000000 RDI:
0000000000000001
RBP:
ffff88809d7af090 R08:
0000000000000001 R09:
0000000000000001
R10:
ffffed1015d05bc7 R11:
ffff888089428600 R12:
0000000000000000
R13:
0000000000000130 R14:
0000000000000001 R15:
0000000000000001
FS:
00007f059044d700(0000) GS:
ffff8880ae800000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00000000004b6040 CR3:
00000000955ca000 CR4:
00000000001406f0
Call Trace:
lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:4211
__raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline]
_raw_spin_lock_irqsave+0x95/0xcd kernel/locking/spinlock.c:152
skb_queue_tail+0x26/0x150 net/core/skbuff.c:2972
rxrpc_reject_packet net/rxrpc/input.c:1126 [inline]
rxrpc_input_packet+0x4a0/0x5536 net/rxrpc/input.c:1414
udp_queue_rcv_one_skb+0xaf2/0x1780 net/ipv4/udp.c:2011
udp_queue_rcv_skb+0x128/0x730 net/ipv4/udp.c:2085
udp_unicast_rcv_skb.isra.0+0xb9/0x360 net/ipv4/udp.c:2245
__udp4_lib_rcv+0x701/0x2ca0 net/ipv4/udp.c:2301
udp_rcv+0x22/0x30 net/ipv4/udp.c:2482
ip_protocol_deliver_rcu+0x60/0x8f0 net/ipv4/ip_input.c:208
ip_local_deliver_finish+0x23b/0x390 net/ipv4/ip_input.c:234
NF_HOOK include/linux/netfilter.h:289 [inline]
NF_HOOK include/linux/netfilter.h:283 [inline]
ip_local_deliver+0x1e9/0x520 net/ipv4/ip_input.c:255
dst_input include/net/dst.h:450 [inline]
ip_rcv_finish+0x1e1/0x300 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:289 [inline]
NF_HOOK include/linux/netfilter.h:283 [inline]
ip_rcv+0xe8/0x3f0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0x115/0x1a0 net/core/dev.c:4987
__netif_receive_skb+0x2c/0x1c0 net/core/dev.c:5099
netif_receive_skb_internal+0x117/0x660 net/core/dev.c:5202
napi_frags_finish net/core/dev.c:5769 [inline]
napi_gro_frags+0xade/0xd10 net/core/dev.c:5843
tun_get_user+0x2f24/0x3fb0 drivers/net/tun.c:1981
tun_chr_write_iter+0xbd/0x156 drivers/net/tun.c:2027
call_write_iter include/linux/fs.h:1866 [inline]
do_iter_readv_writev+0x5e1/0x8e0 fs/read_write.c:681
do_iter_write fs/read_write.c:957 [inline]
do_iter_write+0x184/0x610 fs/read_write.c:938
vfs_writev+0x1b3/0x2f0 fs/read_write.c:1002
do_writev+0x15e/0x370 fs/read_write.c:1037
__do_sys_writev fs/read_write.c:1110 [inline]
__se_sys_writev fs/read_write.c:1107 [inline]
__x64_sys_writev+0x75/0xb0 fs/read_write.c:1107
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes:
5271953cad31 ("rxrpc: Use the UDP encap_rcv hook")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Murphy [Tue, 23 Apr 2019 20:00:24 +0000 (15:00 -0500)]
MAINTAINERS: LEDs: Add designated reviewer for LED subsystem
Add a designated reviewer for the LED subsystem as there
are already two maintainers assigned.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Zhu Yanjun [Wed, 24 Apr 2019 06:56:42 +0000 (02:56 -0400)]
net: rds: exchange of 8K and 1M pool
Before the commit
490ea5967b0d ("RDS: IB: move FMR code to its own file"),
when the dirty_count is greater than 9/10 of max_items of 8K pool,
1M pool is used, Vice versa. After the commit
490ea5967b0d ("RDS: IB: move
FMR code to its own file"), the above is removed. When we make the
following tests.
Server:
rds-stress -r 1.1.1.16 -D 1M
Client:
rds-stress -r 1.1.1.14 -s 1.1.1.16 -D 1M
The following will appear.
"
connecting to 1.1.1.16:4000
negotiated options, tasks will start in 2 seconds
Starting up..header from 1.1.1.166:4001 to id 4001 bogus
..
tsks tx/s rx/s tx+rx K/s mbi K/s mbo K/s tx us/c rtt us
cpu %
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
...
"
So this exchange between 8K and 1M pool is added back.
Fixes: commit
490ea5967b0d ("RDS: IB: move FMR code to its own file")
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov [Wed, 24 Apr 2019 06:53:31 +0000 (09:53 +0300)]
net: sched: flower: refactor reoffload for concurrent access
Recent changes that introduced unlocked flower did not properly account for
case when reoffload is initiated concurrently with filter updates. To fix
the issue, extend flower with 'hw_filters' list that is used to store
filters that don't have 'skip_hw' flag set. Filter is added to the list
when it is inserted to hardware and only removed from it after being
unoffloaded from all drivers that parent block is attached to. This ensures
that concurrent reoffload can still access filter that is being deleted and
prevents race condition when driver callback can be removed when filter is
no longer accessible trough idr, but is still present in hardware.
Refactor fl_change() to respect new filter reference counter and to release
filter reference with __fl_put() in case of error, instead of directly
deallocating filter memory. This allows for concurrent access to filter
from fl_reoffload() and protects it with reference counting. Refactor
fl_reoffload() to iterate over hw_filters list instead of idr. Implement
fl_get_next_hw_filter() helper function that is used to iterate over
hw_filters list with reference counting and skips filters that are being
concurrently deleted.
Fixes:
92149190067d ("net: sched: flower: set unlocked flag for flower proto ops")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rosen Penev [Tue, 23 Apr 2019 20:46:03 +0000 (13:46 -0700)]
net: mvneta: Switch to using devm_alloc_etherdev_mqs
It allows some of the code to be simplified.
Tested on Turris Omnia.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 23 Apr 2019 16:24:46 +0000 (09:24 -0700)]
tipc: tipc_udp_recv() cleanup vs rcu verbs
First thing tipc_udp_recv() does is to use rcu_dereference_sk_user_data(),
and this is really hinting we already own rcu_read_lock() from the caller
(UDP stack).
No need to add another rcu_read_lock()/rcu_read_unlock() pair.
Also use rcu_dereference() instead of rcu_dereference_rtnl()
in the data path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Miaohe Lin [Sat, 20 Apr 2019 04:09:39 +0000 (12:09 +0800)]
net: vrf: Fix operation not supported when set vrf mac
Vrf device is not able to change mac address now because lack of
ndo_set_mac_address. Complete this in case some apps need to do
this.
Reported-by: Hui Wang <wanghui104@huawei.com>
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Balakrishna Godavarthi [Thu, 18 Apr 2019 13:21:23 +0000 (18:51 +0530)]
Bluetooth: hci_core: Don't stop BT if the BD address missing in dts
When flag HCI_QUIRK_USE_BDADDR_PROPERTY is set, we will read the
bluetooth address from dts. If the bluetooth address node is missing
from the dts we will enable it controller UNCONFIGURED state.
This patch enables the normal flow even if the BD address is missing
from the dts tree.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Tested-by: Harish Bandi <c-hbandi@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
David Ahern [Wed, 24 Apr 2019 01:05:33 +0000 (18:05 -0700)]
ipv6: Use result arg in fib_lookup_arg consistently
arg.result is sometimes used as fib6_result and sometimes used to
hold the rt6_info. Add rt6_info to fib6_result and make the use
of arg.result consistent through ipv6 rules.
The rt6 entry is filled in for lookups returning a dst_entry, but not
for direct fib_lookups that just want a fib6_info.
Fixes:
effda4dd97e8 ("ipv6: Pass fib6_result to fib lookups")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 24 Apr 2019 01:06:30 +0000 (18:06 -0700)]
ipv6: fib6_rule_action_alt needs to return -EAGAIN
fib rule actions should return -EAGAIN for the rules to continue to the
next one. A recent change overwrote err with the lookup always returning
0 (future change will make it more like IPv4) which means the rules
stopped at the first (e.g., local table lookup only). Catch and reset err
to -EAGAIN.
Fixes:
effda4dd97e87 ("ipv6: Pass fib6_result to fib lookups")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tao Ren [Wed, 24 Apr 2019 01:43:32 +0000 (01:43 +0000)]
net/ncsi: handle overflow when incrementing mac address
Previously BMC's MAC address is calculated by simply adding 1 to the
last byte of network controller's MAC address, and it produces incorrect
result when network controller's MAC address ends with 0xFF.
The problem can be fixed by calling eth_addr_inc() function to increment
MAC address; besides, the MAC address is also validated before assigning
to BMC.
Fixes:
cb10c7c0dfd9 ("net/ncsi: Add NCSI Broadcom OEM command")
Signed-off-by: Tao Ren <taoren@fb.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 24 Apr 2019 04:08:52 +0000 (21:08 -0700)]
Merge tag 'drm-fixes-2019-04-24' of git://anongit.freedesktop.org/drm/drm
Pull drm regression fixes from Dave Airlie:
"We interrupt your regularly scheduled drm fixes for a regression
special.
The first is for a fix in i915 that had unexpected side effects
fallout in the userspace X.org modesetting driver where X would no
longer start. I got tired of the nitpicking and issued a large hammer
on it. The X.org driver is buggy, but blackscreen regressions are
worse.
The second was an oversight that myself and Gerd should have noticed
better, Gerd is trying to fix this properly, but the regression is too
large to leave, even if the original behaviour is bad in some cases,
it's clearly bad to break a bunch of working use cases.
I'll likely have a regular fixes pull later, but I really wanted to
highlight these"
* tag 'drm-fixes-2019-04-24' of git://anongit.freedesktop.org/drm/drm:
Revert "drm/virtio: drop prime import/export callbacks"
Revert "drm/i915/fbdev: Actually configure untiled displays"
David Ahern [Tue, 23 Apr 2019 23:03:29 +0000 (16:03 -0700)]
mlxsw: spectrum_router: Prevent ipv6 gateway with v4 route via replace and append
mlxsw currently does not support v6 gateways with v4 routes. Commit
19a9d136f198 ("ipv4: Flag fib_info with a fib_nh using IPv6 gateway")
prevents a route from being added, but nothing stops the replace or
append. Add a catch for them too.
$ ip ro add 172.16.2.0/24 via 10.99.1.2
$ ip ro replace 172.16.2.0/24 via inet6 fe80::202:ff:fe00:b dev swp1s0
Error: mlxsw_spectrum: IPv6 gateway with IPv4 route is not supported.
$ ip ro append 172.16.2.0/24 via inet6 fe80::202:ff:fe00:b dev swp1s0
Error: mlxsw_spectrum: IPv6 gateway with IPv4 route is not supported.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Apr 2019 02:52:33 +0000 (19:52 -0700)]
Merge branch 'Taprio-qdisc-fixes'
Andre Guedes says:
====================
Taprio qdisc fixes
I'm re-sending this series, now with the "net-next" prefix in the subject.
The only change from the previous version is in patch 3. As suggested by Cong
Wang, it removes the !entry check within should_restart_cycle() since it is
already checked by the caller. As a side effect, that function becomes a dummy
wrapper on list_is_last() so we simply remove it and call list_is_last()
instead.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Guedes [Tue, 23 Apr 2019 19:44:24 +0000 (12:44 -0700)]
net: sched: taprio: Fix taprio_dequeue()
In case we don't have 'guard' or 'budget' to transmit the skb, we should
continue traversing the qdisc list since the remaining guard/budget
might be enough to transmit a skb from other children qdiscs.
Fixes:
5a781ccbd19e (“tc: Add support for configuring the taprio scheduler”)
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Guedes [Tue, 23 Apr 2019 19:44:23 +0000 (12:44 -0700)]
net: sched: taprio: Fix taprio_peek()
While traversing taprio's children qdisc list, if the gate is closed for
a given traffic class, we should continue traversing the list since the
remaining qdiscs may have skb ready for transmission.
This patch also takes this opportunity and changes the function to use
the TAPRIO_ALL_GATES_OPEN macro instead of the magic number '-1'.
Fixes:
5a781ccbd19e (“tc: Add support for configuring the taprio scheduler”)
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Guedes [Tue, 23 Apr 2019 19:44:22 +0000 (12:44 -0700)]
net: sched: taprio: Remove should_restart_cycle()
The 'entry' argument from should_restart_cycle() cannot be NULL since it
is already checked by the caller so the WARN_ON() within should_
restart_cycle() could be removed. By doing that, that function becomes
a dummy wrapper on list_is_last() so this patch simply gets rid of it
and call list_is_last() within advance_sched() instead.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Guedes [Tue, 23 Apr 2019 19:44:21 +0000 (12:44 -0700)]
net: sched: taprio: Refactor taprio_get_start_time()
This patch does a code refactoring to taprio_get_start_time() function
to improve readability and report error properly.
If 'base' time is later than 'now', the start time is equal to 'base'
and taprio_get_start_time() is done. That's the natural case so we move
that code to the beginning of the function. Also, if 'cycle' calculation
is zero, something went really wrong with taprio and we should log that
internal error properly.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Guedes [Tue, 23 Apr 2019 19:44:20 +0000 (12:44 -0700)]
net: sched: taprio: Remove pointless variable assigment
This patch removes a pointless variable assigment in taprio_change().
The 'err' variable is not used from this assignment to the next one so
this patch removes it.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 23 Apr 2019 15:48:09 +0000 (08:48 -0700)]
net: Change nhc_flags to unsigned char
nhc_flags holds the RTNH_F flags for a given nexthop (fib{6}_nh).
All of the RTNH_F_ flags fit in an unsigned char, and since the API to
userspace (rtnh_flags and lower byte of rtm_flags) is 1 byte it can not
grow. Make nhc_flags in fib_nh_common an unsigned char and shrink the
size of the struct by 8, from 56 to 48 bytes.
Update the flags arguments for up netdevice events and fib_nexthop_info
which determines the RTNH_F flags to return on a dump/event. The RTNH_F
flags are passed in the lower byte of rtm_flags which is an unsigned int
so use a temp variable for the flags to fib_nexthop_info and combine
with rtm_flags in the caller.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 23 Apr 2019 15:23:41 +0000 (08:23 -0700)]
lwtunnel: Pass encap and encap type attributes to lwtunnel_fill_encap
Currently, lwtunnel_fill_encap hardcodes the encap and encap type
attributes as RTA_ENCAP and RTA_ENCAP_TYPE, respectively. The nexthop
objects want to re-use this code but the encap attributes passed to
userspace as NHA_ENCAP and NHA_ENCAP_TYPE. Since that is the only
difference, change lwtunnel_fill_encap to take the attribute type as
an input.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilias Apalodimas [Tue, 23 Apr 2019 06:01:41 +0000 (09:01 +0300)]
net: socionext: replace napi_alloc_frag with the netdev variant on init
The netdev variant is usable on any context since it disables interrupts.
The napi variant of the call should only be used within softirq context.
Replace napi_alloc_frag on driver init with the correct netdev_alloc_frag
call
Changes since v1:
- Adjusted commit message
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Fixes:
4acb20b46214 ("net: socionext: different approach on DMA")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 23 Apr 2019 14:30:07 +0000 (15:30 +0100)]
net: atheros: fix spelling mistake "underun" -> "underrun"
There are spelling mistakes in structure elements, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Tue, 23 Apr 2019 13:01:53 +0000 (15:01 +0200)]
ravb: Avoid unsupported internal delay mode for R-Car E3/D3
According to the R-Car Gen3 Hardware Manual Rev 1.50 of Nov 30, 2018, the
TX clock internal delay mode isn't supported on R-Car E3 (r8a77990) or D3
(r8a77995). And by extension it is also not supported by RZ/G2E (r9a774c0).
This matches all ES versions of the affected SoCs as it is
not clear if this problem will be resolved in newer chips.
This can be revisited, as necessary.
This patch does not error-out if PHY_INTERFACE_MODE_RGMII_ID or
PHY_INTERFACE_MODE_RGMII_TXID are used on SoCs where TX clock delay
mode is not supported as there is a risk of introducing a regression
when used in conjunction with older DT blobs present in the field.
Rather, a warning is logged in such cases.
Based on work by Kazuya Mizuguchi.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Rothwell [Tue, 23 Apr 2019 07:25:24 +0000 (17:25 +1000)]
net: fix sparc64 compilation of sock_gettstamp
net/core/sock.c: In function 'sock_gettstamp':
net/core/sock.c:3007:23: error: expected '}' before ';' token
.tv_sec = ts.tv_sec;
^
net/core/sock.c:3011:4: error: expected ')' before 'return'
return -EFAULT;
^~~~~~
net/core/sock.c:3013:2: error: expected expression before '}' token
}
^
Fixes:
c7cbdbf29f48 ("net: rework SIOCGSTAMP ioctl handling")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fuqian Huang [Tue, 23 Apr 2019 02:56:23 +0000 (10:56 +0800)]
isdn:mISDN: fix misuse of %x in hfcpci.c
Pointers should be printed with %p or %px rather than
cast to (u_long) and printed with %lx.
Change %lx to %p to print the pointer.
Change %lx to %pad to print the dma_addr_t.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fuqian Huang [Tue, 23 Apr 2019 02:25:28 +0000 (10:25 +0800)]
isdn: hisax: Fix misuse of %x in config.c
Pointers should be printed with %p or %px rather than
cast to (u_long) type and printed with %lX.
As the function seems to be for debug purpose.
Change %lX to %px to print the pointer value.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Airlie [Wed, 24 Apr 2019 00:52:20 +0000 (10:52 +1000)]
Revert "drm/virtio: drop prime import/export callbacks"
This patch does more harm than good, as it breaks both Xwayland and
gnome-shell with X11.
Xwayland requires DRI3 & DRI3 requires PRIME.
X11 crash for obscure double-free reason which are hard to debug
(starting X11 by hand doesn't trigger the crash).
I don't see an apparent problem implementing those stub prime
functions, they may return an error at run-time, and it seems to be
handled fine by GNOME at least.
This reverts commit
b318e3ff7ca065d6b107e424c85a63d7a6798a69.
[airlied:
This broke userspace for virtio-gpus, and regressed things from DRI3 to DRI2.
This brings back the original problem, but it's better than regressions.]
Fixes:
b318e3ff7ca065d6b107e424c85a63d7a6798a ("drm/virtio: drop prime import/export callbacks")
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Wed, 24 Apr 2019 00:47:56 +0000 (10:47 +1000)]
Revert "drm/i915/fbdev: Actually configure untiled displays"
This reverts commit
d179b88deb3bf6fed4991a31fd6f0f2cad21fab5.
This commit is documented to break userspace X.org modesetting driver in certain configurations.
The X.org modesetting userspace driver is broken. No fixes are available yet. In order for this patch to be applied it either needs a config option or a workaround developed.
This has been reported a few times, saying it's a userspace problem is clearly against the regression rules.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109806
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cc: <stable@vger.kernel.org> # v3.19+
David S. Miller [Wed, 24 Apr 2019 00:19:48 +0000 (17:19 -0700)]
Merge branch 'ipv6-fib6_ref-conversion-to-refcount_t'
Eric Dumazet says:
====================
ipv6: fib6_ref conversion to refcount_t
We are chasing use-after-free in IPv6 that could have their origin
in fib6_ref 0 -> 1 transitions.
This patch series should help finding the root causes if these
illegal transitions ever happen.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 23 Apr 2019 01:35:03 +0000 (18:35 -0700)]
ipv6: convert fib6_ref to refcount_t
We suspect some issues involving fib6_ref 0 -> 1 transitions might
cause strange syzbot reports.
Lets convert fib6_ref to refcount_t to catch them earlier.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 23 Apr 2019 01:35:02 +0000 (18:35 -0700)]
ipv6: broadly use fib6_info_hold() helper
Instead of using atomic_inc(), prefer fib6_info_hold()
so that upcoming refcount_t conversion is simpler.
Only fib6_info_alloc() is using atomic_set() since we
just allocated a new object.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 23 Apr 2019 01:35:01 +0000 (18:35 -0700)]
ipv6: fib6_info_destroy_rcu() cleanup
We do not need to clear f6i->rt6i_exception_bucket right before
freeing f6i.
Note that f6i->rt6i_exception_bucket is properly protected by
f6i->exception_bucket_flushed being set to one in rt6_flush_exceptions()
under the protection of rt6_exception_lock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Apr 2019 00:03:40 +0000 (17:03 -0700)]
Merge tag 'mlx5-updates-2019-04-22' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-04-22
This series includes updates to mlx5e driver RX data path and some
significant XDP RX/TX improvements to overcome/mitigate HW and PCIE
bottlenecks.
From Tariq:
1) Some Enhancements in rq->flags
2) Stabilize RX packet rate (on Striding RQ) with
multiple outstanding UMR posts
In this patch, we add support for multiple outstanding UMR posts,
to allow faster gap closure between consuming MPWQEs and reposting
them back into the WQ.
Performance test:
As expected, huge improvement in large-scale (48 cores).
xdp_redirect_map, 64B UDP multi-stream.
Redirect from ConnectX-5 100Gbps to ConnectX-6 100Gbps.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz.
Before: Unstable, 7 to 30 Mpps
After: Stable, at 70.5 Mpps
From Shay:
3) XDP, Inline small packets into the TX MPWQE in XDP xmit flow
Upon high packet rate with multiple CPUs TX workloads, much of the HCA's
resources are spent on prefetching TX descriptors, thus affecting
transmission rates.
This patch comes to mitigate this problem by moving some workload to the
CPU and reducing the HW data prefetch overhead for small packets (<= 256B).
When forwarding packets with XDP, a packet that is smaller
than a certain size (set to ~256 bytes) would be sent inline within
its WQE TX descrptor (mem-copied), when the hardware tx queue is congested
beyond a pre-defined water-mark.
Performance:
Tested packet rate for UDP 64Byte multi-stream
over two dual port ConnectX-5 100Gbps NICs.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
* Tested with hyper-threading disabled
XDP_TX:
| | before | after | |
| 24 rings | 51Mpps | 116Mpps | +126% |
| 1 ring | 12Mpps | 12Mpps | same |
XDP_REDIRECT:
** Below is the transmit rate, not the redirection rate
which might be larger, and is not affected by this patch.
| | before | after | |
| 32 rings | 64Mpps | 92Mpps | +43% |
| 1 ring | 6.4Mpps | 6.4Mpps | same |
As we can see, feature significantly improves scaling, without
hurting single ring performance.
From Maxim:
4) Some trivial refactoring and code improvements prior to a larger series
to support AF_XDP.
====================
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 23 Apr 2019 20:40:55 +0000 (13:40 -0700)]
Merge tag 'nfsd-5.1-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfixes from Bruce Fields:
"Fix miscellaneous nfsd bugs, in NFSv4.1 callbacks, NFSv4.1
lock-notification callbacks, NFSv3 readdir encoding, and the
cache/upcall code"
* tag 'nfsd-5.1-1' of git://linux-nfs.org/~bfields/linux:
nfsd: wake blocked file lock waiters before sending callback
nfsd: wake waiters blocked on file_lock before deleting it
nfsd: Don't release the callback slot unless it was actually held
nfsd/nfsd3_proc_readdir: fix buffer count and page pointers
sunrpc: don't mark uninitialised items as VALID.
Linus Torvalds [Tue, 23 Apr 2019 20:34:17 +0000 (13:34 -0700)]
Merge tag 'syscalls-5.1' of git://git./linux/kernel/git/arnd/asm-generic
Pull syscall numbering updates from Arnd Bergmann:
"arch: add pidfd and io_uring syscalls everywhere
This comes a bit late, but should be in 5.1 anyway: we want the newly
added system calls to be synchronized across all architectures in the
release.
I hope that in the future, any newly added system calls can be added
to all architectures at the same time, and tested there while they are
in linux-next, avoiding dependencies between the architecture
maintainer trees and the tree that contains the new system call"
* tag 'syscalls-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
arch: add pidfd and io_uring syscalls everywhere
Matthias Kaehlcke [Tue, 23 Apr 2019 18:16:52 +0000 (11:16 -0700)]
Bluetooth: hci_qca: Fix crash with non-serdev devices
qca_set_baudrate() calls serdev_device_wait_until_sent() assuming that
the HCI is always associated with a serdev device. This isn't true for
ROME controllers instantiated through ldisc, where the call causes a
crash due to a NULL pointer dereferentiation. Only call the function
when we have a serdev device. The timeout for ROME devices at the end
of qca_set_baudrate() is long enough to be reasonably sure that the
command was sent.
Fixes:
fa9ad876b8e0 ("Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990")
Reported-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reported-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Rocky Liao <rjliao@codeaurora.org>
Tested-by: Rocky Liao <rjliao@codeaurora.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Maxim Mikityanskiy [Tue, 5 Mar 2019 12:46:16 +0000 (14:46 +0200)]
net/mlx5e: Use #define for the WQE wait timeout constant
Create a #define for the timeout of mlx5e_wait_for_min_rx_wqes to
clarify the meaning of a magic number.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Maxim Mikityanskiy [Thu, 21 Mar 2019 13:22:57 +0000 (15:22 +0200)]
net/mlx5e: Remove unused rx_page_reuse stat
Remove the no longer used page_reuse stat of RQs.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Maxim Mikityanskiy [Fri, 1 Mar 2019 10:05:21 +0000 (12:05 +0200)]
net/mlx5e: Take HW interrupt trigger into a function
mlx5e_trigger_irq posts a NOP to the ICO SQ just to trigger an IRQ and
enter the NAPI poll on the right CPU according to the affinity. Use it
in mlx5e_activate_rq.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Maxim Mikityanskiy [Wed, 27 Mar 2019 11:46:50 +0000 (13:46 +0200)]
net/mlx5e: Remove unused parameter
mdev is unused in mlx5e_rx_is_linear_skb.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Maxim Mikityanskiy [Wed, 27 Mar 2019 11:39:21 +0000 (13:39 +0200)]
net/mlx5e: Add an underflow warning comment
mlx5e_mpwqe_get_log_rq_size calculates the number of WQEs (N) based on
the requested number of frames in the RQ (F) and the number of packets
per WQE (P). It ensures that N is not less than the minimum number of
WQEs in an RQ (N_min). Arithmetically, it means that F / P >= N_min
should be true. This function deals with logarithms, so it should check
that log(F) - log(P) >= log(N_min). However, if F < P, this expression
will cause an unsigned underflow. Check log(F) >= log(P) + log(N_min)
instead.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Maxim Mikityanskiy [Wed, 27 Mar 2019 11:09:27 +0000 (13:09 +0200)]
net/mlx5e: Move parameter calculation functions to en/params.c
This commit moves the parameter calculation functions to a separate file
for better modularity and code sharing with future features.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Maxim Mikityanskiy [Tue, 19 Mar 2019 16:32:37 +0000 (18:32 +0200)]
net/mlx5e: Report mlx5e_xdp_set errors
If the channels fail to reopen after setting an XDP program, return the
error code instead of 0. A proper fix is still needed, as now any error
while reopening the channels brings the interface down. This patch only
adds error reporting.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Maxim Mikityanskiy [Thu, 7 Mar 2019 17:30:30 +0000 (19:30 +0200)]
net/mlx5e: Remove unused parameter
params is unused in mlx5e_init_di_list.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Shay Agroskin [Thu, 14 Mar 2019 12:54:07 +0000 (14:54 +0200)]
net/mlx5e: XDP, Inline small packets into the TX MPWQE in XDP xmit flow
Upon high packet rate with multiple CPUs TX workloads, much of the HCA's
resources are spent on prefetching TX descriptors, thus affecting
transmission rates.
This patch comes to mitigate this problem by moving some workload to the
CPU and reducing the HW data prefetch overhead for small packets (<= 256B).
When forwarding packets with XDP, a packet that is smaller
than a certain size (set to ~256 bytes) would be sent inline within
its WQE TX descrptor (mem-copied), when the hardware tx queue is congested
beyond a pre-defined water-mark.
This is added to better utilize the HW resources (which now makes
one less packet data prefetch) and allow better scalability, on the
account of CPU usage (which now 'memcpy's the packet into the WQE).
To load balance between HW and CPU and get max packet rate, we use
watermarks to detect how much the HW is congested and move the work
loads back and forth between HW and CPU.
Performance:
Tested packet rate for UDP 64Byte multi-stream
over two dual port ConnectX-5 100Gbps NICs.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
* Tested with hyper-threading disabled
XDP_TX:
| | before | after | |
| 24 rings | 51Mpps | 116Mpps | +126% |
| 1 ring | 12Mpps | 12Mpps | same |
XDP_REDIRECT:
** Below is the transmit rate, not the redirection rate
which might be larger, and is not affected by this patch.
| | before | after | |
| 32 rings | 64Mpps | 92Mpps | +43% |
| 1 ring | 6.4Mpps | 6.4Mpps | same |
As we can see, feature significantly improves scaling, without
hurting single ring performance.
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Shay Agroskin [Mon, 25 Feb 2019 16:02:09 +0000 (18:02 +0200)]
net/mlx5e: XDP, Add TX MPWQE session counter
This counter tracks how many TX MPWQE sessions are started in XDP SQ
in XDP TX/REDIRECT flow. It counts per-channel and global stats.
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tariq Toukan [Sun, 10 Mar 2019 13:35:58 +0000 (15:35 +0200)]
net/mlx5e: XDP, Enhance RQ indication for XDP redirect flush
The XDP redirect flush indication belongs to the receive queue,
not to its XDP send queue.
For this, use a new bit on rq->flags.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tariq Toukan [Sun, 10 Mar 2019 13:29:13 +0000 (15:29 +0200)]
net/mlx5e: XDP, Fix shifted flag index in RQ bitmap
Values in enum mlx5e_rq_flag are used as bit indixes.
Intention was to use them with no BIT(i) wrapping.
No functional bug fix here, as the same (shifted)flag bit
is used for all set, test, and clear operations.
Fixes:
121e89275471 ("net/mlx5e: Refactor RQ XDP_TX indication")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tariq Toukan [Wed, 27 Feb 2019 10:06:08 +0000 (12:06 +0200)]
net/mlx5e: RX, Support multiple outstanding UMR posts
The buffers mapping of the Multi-Packet WQEs (of Striding RQ)
is done via UMR posts, one UMR WQE per an RX MPWQE.
A single MPWQE is capable of serving many incoming packets,
usually larger than the budget of a single napi cycle.
Hence, posting a single UMR WQE per napi cycle (and handling its
completion in the next cycle) works fine in many common cases,
but not always.
When an XDP program is loaded, every MPWQE is capable of serving less
packets, to satisfy the packet-per-page requirement.
Thus, for the same number of packets more MPWQEs (and UMR posts)
are needed (twice as much for the default MTU), giving less latency
room for the UMR completions.
In this patch, we add support for multiple outstanding UMR posts,
to allow faster gap closure between consuming MPWQEs and reposting
them back into the WQ.
For better SW and HW locality, we combine the UMR posts in bulks of
(at least) two.
This is expected to improve packet rate in high CPU scale.
Performance test:
As expected, huge improvement in large-scale (48 cores).
xdp_redirect_map, 64B UDP multi-stream.
Redirect from ConnectX-5 100Gbps to ConnectX-6 100Gbps.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz.
Before: Unstable, 7 to 30 Mpps
After: Stable, at 70.5 Mpps
No degradation in other tested scenarios.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Saeed Mahameed [Tue, 23 Apr 2019 18:57:33 +0000 (11:57 -0700)]
Merge branch 'mlx5-next' of git://git./linux/kernel/git/mellanox/linux
David S. Miller [Tue, 23 Apr 2019 17:47:58 +0000 (10:47 -0700)]
Merge branch 'net-phy-mscc-Improvements-to-VSC8514-PHY-driver'
Kavya Sree Kotagiri says:
====================
net: phy: mscc: Improvements to VSC8514 PHY driver.
The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X, can communicate with the MAC via QSGMII.
The MAC interface protocol for each port within QSGMII can
be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is
connecting to supports this functionality.
VSC8514 also supports SGMII MAC-side autonegotiation on each individual
port, downshifting, can set the blinking pattern of each of its 4 LEDs,
SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection.
This patch series adds support for 10BASE-T, 100BASE-TX, and
1000BASE-T, QSGMII link with the MAC, downshifting, HP Auto-MDIX
detection and blinking pattern for its 4 LEDs.
The GPIO register bank is a set of registers that are common to all
PHYs in the package. So any modification in any register of this bank
affects all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
This patch series adds support for VSC8514 in Microsemi driver(mscc.c)
and removes support from Vitesse driver(vitesse.c).
v8
- mscc: Added appropriate code using phy_modify() in vsc8514_config_init().
v7
- mscc: Handled return values in vsc8514_config_init().
v6
- mscc: Added proper return value in vsc85xx_csr_ctrl_phy_read().
- mscc: Replaced __mdiobus_write and__mdiobus_read with __phy_write and __phy_read resp.
- mscc: Replaced register addresses in 8514_config_init() with proper constants.
v5
- mscc: Added return error statements for few function calls.
- mscc: Added comments in vsc85xx_csr_ctrl_phy_read() and vsc85xx_csr_ctrl_phy_write()
v4
- mscc: Removed features settings
- mscc: Removed aneg_done settings.
v3
- mscc: Used BIT(x) for PHY_MCB_S6G_WRITE and PHY_MCB_S6G_READ
instead of hex.
- mscc: Replaced magic numbers with proper constants.
- mscc: Handled delays and timeouts at appropriate points.
- mscc: Added comments/explanation where requested.
v2
- mscc: Sorted variable declarations in reverse christmas tree order.
v1
- Added 0/2 file.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kavya Sree Kotagiri [Mon, 22 Apr 2019 11:52:04 +0000 (11:52 +0000)]
net: phy: vitesse: Remove support for VSC8514.
Add support for VSC8514 in Microsemi driver (mscc.c)
with more features.
Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kavya Sree Kotagiri [Mon, 22 Apr 2019 11:51:35 +0000 (11:51 +0000)]
net: phy: mscc: add support for VSC8514 PHY.
The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X, can communicate with the MAC via QSGMII.
The MAC interface protocol for each port within QSGMII can
be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is
connecting to supports this functionality.
VSC8514 also supports SGMII MAC-side autonegotiation on each individual
port, downshifting, can set the blinking pattern of each of its 4 LEDs,
SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection.
This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T,
QSGMII link with the MAC, downshifting, HP Auto-MDIX detection
and blinking pattern for its 4 LEDs.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Gomez [Mon, 22 Apr 2019 19:08:04 +0000 (21:08 +0200)]
spi: ST ST95HF NFC: declare missing of table
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/nfc/st95hf/st95hf.ko | grep alias
alias: spi:st95hf
After this patch:
modinfo drivers/nfc/st95hf/st95hf.ko | grep alias
alias: spi:st95hf
alias: of:N*T*Cst,st95hfC*
alias: of:N*T*Cst,st95hf
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Gomez [Mon, 22 Apr 2019 19:08:03 +0000 (21:08 +0200)]
spi: Micrel eth switch: declare missing of table
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
After this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
alias: of:N*T*Cmicrel,ksz8795C*
alias: of:N*T*Cmicrel,ksz8795
alias: of:N*T*Cmicrel,ksz8864C*
alias: of:N*T*Cmicrel,ksz8864
alias: of:N*T*Cmicrel,ks8995C*
alias: of:N*T*Cmicrel,ks8995
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Mon, 22 Apr 2019 13:52:23 +0000 (21:52 +0800)]
net: phy: marvell: add new default led configure for m88e151x
The default m88e151x LED configuration is 0x1177, used LED[0]
for 1000M link, LED[1] for 100M link, and LED[2] for active.
But for some boards, which use LED[0] for link, and LED[1] for
active, prefer to be 0x1040. To be compatible with this case,
this patch defines a new dev_flag, and set it before connect
phy in HNS3 driver. When phy initializing, using the new
LED configuration if this dev_flag is set.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Thu, 28 Mar 2019 17:30:29 +0000 (12:30 -0500)]
Bluetooth: Use struct_size() helper
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
size = struct_size(instance, entry, count);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Balakrishna Godavarthi [Mon, 1 Apr 2019 09:49:08 +0000 (15:19 +0530)]
Bluetooth: hci_qca: Give enough time to ROME controller to bootup.
This patch enables enough time to ROME controller to bootup
after we bring the enable pin out of reset.
Fixes:
05ba533c5c11 ("Bluetooth: hci_qca: Add serdev support").
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Rocky Liao <rjliao@codeaurora.org>
Tested-by: Rocky Liao <rjliao@codeaurora.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Chen-Yu Tsai [Mon, 1 Apr 2019 03:43:12 +0000 (11:43 +0800)]
Bluetooth: hci_bcm: Fix empty regulator supplies for Intel Macs
The code path for Macs goes through bcm_apple_get_resources(), which
skips over the code that sets up the regulator supplies. As a result,
the call to regulator_bulk_enable() / regulator_bulk_disable() results
in a NULL pointer dereference.
This was reported on the kernel.org Bugzilla, bug 202963.
Unbreak Broadcom Bluetooth support on Intel Macs by checking if the
supplies were set up before enabling or disabling them.
The same does not need to be done for the clocks, as the common clock
framework API checks for NULL pointers.
Fixes:
75d11676dccb ("Bluetooth: hci_bcm: Add support for regulator supplies")
Cc: <stable@vger.kernel.org> # 5.0.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jaganath Kanakkassery [Wed, 3 Apr 2019 06:41:44 +0000 (12:11 +0530)]
Bluetooth: Fix incorrect pointer arithmatic in ext_adv_report_evt
In ext_adv_report_event rssi comes before data (not after data as
in legacy adv_report_evt) so "+ 1" is not required in the ptr arithmatic
to point to next report.
Signed-off-by: Jaganath Kanakkassery <jaganath.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Stephan Gerhold [Tue, 5 Mar 2019 13:09:00 +0000 (14:09 +0100)]
Bluetooth: btbcm: Add entry for BCM2076B1 UART Bluetooth
Add the device ID for the BT/FM/GPS combo chip BCM2076 (rev B1)
used in the AMPAK AP6476 WiFi/BT/FM/GPS module.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Dan Carpenter [Wed, 3 Apr 2019 05:34:16 +0000 (08:34 +0300)]
6lowpan: Off by one handling ->nexthdr
NEXTHDR_MAX is 255. What happens here is that we take a u8 value
"hdr->nexthdr" from the network and then look it up in
lowpan_nexthdr_nhcs[]. The problem is that if hdr->nexthdr is 0xff then
we read one element beyond the end of the array so the array needs to
be one element larger.
Fixes:
92aa7c65d295 ("6lowpan: add generic nhc layer interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Acked-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Ferry Toth [Tue, 9 Apr 2019 14:15:50 +0000 (16:15 +0200)]
Bluetooth: btbcm: Add default address for BCM43341B
The BCM43341B has the default MAC address 43:34:1B:00:1F:AC if none
is given. This address was found when enabling Bluetooth on multiple
Intel Edison modules. It also contains the sequence 43341B, the name
the chip identifies itself as. Using the same BD_ADDR is problematic
when having multiple Intel Edison modules in each others range.
The default address also has the LAA (locally administered address)
bit set which prevents a BNEP device from being created, needed for
BT tethering.
Add this to the list of black listed default MAC addresses and let
the user configure a valid one using f.i.
`btmgmt -i hci0 public-addr xx:xx:xx:xx:xx:xx`
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Young Xiao [Fri, 12 Apr 2019 07:24:30 +0000 (15:24 +0800)]
Bluetooth: hidp: fix buffer overflow
Struct ca is copied from userspace. It is not checked whether the "name"
field is NULL terminated, which allows local users to obtain potentially
sensitive information from kernel stack memory, via a HIDPCONNADD command.
This vulnerability is similar to CVE-2011-1079.
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Tamás Szűcs [Sun, 14 Apr 2019 18:38:14 +0000 (20:38 +0200)]
Bluetooth: btmrvl: add support for SD8987 chipset
This patch adds support for Marvell 88W8987 chipset with SDIO interface.
Register offsets and supported feature flags are updated. The corresponding
firmware image file shall be "mrvl/sd8987_uapsta.bin".
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Thu, 18 Apr 2019 09:08:02 +0000 (17:08 +0800)]
Bluetooth: btmtksdio: Add runtime PM support to SDIO based Bluetooth
Add runtime PM support to btmtksdio. With this way, there will be the
benefit of the device entering the more power saving state once it is
been a while data traffic is idle.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Thu, 18 Apr 2019 09:08:01 +0000 (17:08 +0800)]
Bluetooth: btmtksdio: Fix hdev->stat.byte_rx accumulation
Accumulate hdev->stat.byte_rx only for valid packets as btmtkuart doing.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Thu, 18 Apr 2019 09:08:00 +0000 (17:08 +0800)]
Bluetooth: btmtksdio: Add a bit definition for CHLPCR
Add a register bit definition about CHLPCR bit 8 because the bit is quite
different in the meaning between reading and writing that bit.
The patch adds a definition particularly for the bit read to avoid the
confusion about using write definition to read the bit.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Thu, 18 Apr 2019 09:07:59 +0000 (17:07 +0800)]
Bluetooth: btmtksdio: Drop newline with bt_dev logging macros
bt_dev logging macros already include a newline at each output
so drop these unnecessary additional newlines in the driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Colin Ian King [Tue, 23 Apr 2019 14:50:22 +0000 (15:50 +0100)]
Bluetooth: hci_h5: fix spelling mistake "sliped" -> "slipped"
There is a spelling mistake in a BT_DBG debug message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Tue, 5 Mar 2019 00:14:25 +0000 (08:14 +0800)]
Bluetooth: mediatek: Fixed incorrect type in assignment
Fixed warning: incorrect type in assignment reported by kbuild test robot.
The detailed warning is shown as below.
make ARCH=x86_64 allmodconfig
make C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__'
All warnings (new ones prefixed by >>):
btmtkuart.c:671:18: sparse: warning: incorrect type in assignment
(different base types)
btmtkuart.c:671:18: sparse: expected unsigned int [usertype] baudrate
btmtkuart.c:671:18: sparse: got restricted __le32 [usertype]
sparse warnings: (new ones prefixed by >>)
btmtkuart.c:671:18: sparse: warning: incorrect type in assignment
(different base types)
btmtkuart.c:671:18: sparse: expected unsigned int [usertype] baudrate
btmtkuart.c:671:18: sparse: got restricted __le32 [usertype]
vim +671 drivers/bluetooth/btmtkuart.c
659
660 static int btmtkuart_change_baudrate(struct hci_dev *hdev)
661 {
662 struct btmtkuart_dev *bdev = hci_get_drvdata(hdev);
663 struct btmtk_hci_wmt_params wmt_params;
664 u32 baudrate;
665 u8 param;
666 int err;
667
668 /* Indicate the device to enter the probe state the host is
669 * ready to change a new baudrate.
670 */
> 671 baudrate = cpu_to_le32(bdev->desired_speed);
672 wmt_params.op = MTK_WMT_HIF;
Fixes:
22eaf6c9946a ("Bluetooth: mediatek: add support for MediaTek MT7663U and MT7668U UART devices")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Mon, 18 Mar 2019 20:58:33 +0000 (04:58 +0800)]
Bluetooth: btmtksdio: fix uninitialized symbol errors in btmtksdio_rx_packet
Fixed all the below warnings. They would probably cause the following
error handling path would use the uninitialized value and then produce
unexpected behavior.
drivers/bluetooth/btmtksdio.c:470:2: warning: ‘old_len’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
print_hex_dump(KERN_ERR, "err sdio rx: ", DUMP_PREFIX_NONE, 4, 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
old_data, old_len, true);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/bluetooth/btmtksdio.c:376:15: note: ‘old_len’ was declared here
unsigned int old_len;
^~~~~~~
drivers/bluetooth/btmtksdio.c:470:2: warning: ‘old_data’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
print_hex_dump(KERN_ERR, "err sdio rx: ", DUMP_PREFIX_NONE, 4, 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
old_data, old_len, true);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/bluetooth/btmtksdio.c:375:17: note: ‘old_data’ was declared here
unsigned char *old_data;
^~~~~~~~
v2: Remove old_len and old_data because the error path for sdio_readsb also
seems wrong. And change the prefix from "mediatek" to "btmtksdio".
Fixes:
d74eef2834b5 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Wed, 13 Mar 2019 21:02:00 +0000 (05:02 +0800)]
Bluetooth: btsdio: Use module_sdio_driver helper
Macro module_sdio_driver is used for drivers whose init and exit paths
only register and unregister to SDIO API. So remove boilerplate code to
make code simpler by using module_sdio_driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Wed, 13 Mar 2019 21:01:59 +0000 (05:01 +0800)]
Bluetooth: mediatek: Use module_sdio_driver helper
Macro module_sdio_driver is used for drivers whose init and exit paths
only register and unregister to SDIO API. So remove boilerplate code to
make code simpler by using module_sdio_driver.
Suggested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Wed, 13 Mar 2019 21:01:58 +0000 (05:01 +0800)]
mmc: sdio: Add helper macro for sdio_driver boilerplate
This patch introduces the module_sdio_driver macro which is a convenience
macro for SDIO driver modules similar to module_usb_driver. It is intended
to be used by drivers which init/exit section does nothing but register/
unregister the SDIO driver. By using this macro it is possible to eliminate
a few lines of boilerplate code per SDIO driver.
Suggested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fugang Duan [Fri, 15 Mar 2019 03:17:28 +0000 (03:17 +0000)]
Bluetooth: Add return check for L2CAP security level set
Add return check for security level set for socket interface since
stack will check the return value.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz [Thu, 14 Mar 2019 13:43:37 +0000 (15:43 +0200)]
Bluetooth: Fix not initializing L2CAP tx_credits
l2cap_le_flowctl_init was reseting the tx_credits which works only for
outgoing connection since that set the tx_credits on the response, for
incoming connections that was not the case which leaves the channel
without any credits causing it to be suspended.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 4.20+
Matthias Kaehlcke [Tue, 12 Mar 2019 23:02:57 +0000 (16:02 -0700)]
Bluetooth: btqca: Fix misspelling of 'baudrate'
Rename the misspelled struct 'qca_bardrate' to 'qca_baudrate'
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Matthias Kaehlcke [Mon, 11 Mar 2019 18:38:31 +0000 (11:38 -0700)]
Bluetooth: hci_qca: Add helper function to get the chip family
Many functions obtain a 'struct qca_serdev' only to read the btsoc_type
field. Add a helper function that encapsulates this.
This also fixes crashes observed on platforms with ROME controllers
that are instantiated through ldisc and not as serdev clients. The
crashes are caused by NULL pointer dereferentiations, which stem from
the driver's assumption that a QCA HCI device is always associated with
a serdev device.
Fixes:
fa9ad876b8e0 ("Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990")
Reported-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Fri, 8 Mar 2019 01:15:44 +0000 (09:15 +0800)]
Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices
This adds the support of enabling MT7663S and MT7668S SDIO-based
Bluetooth function.
There are quite many differences between MT766[3,8]S and standard
Bluetooth SDIO devices such as Type-A and Type-B devices. For example,
MT766[3,8]S have its own SDIO registers layout, definition, SDIO packet
format, and the specific flow should be programmed on them to complete
the device initialization and low power control and so on.
Currently, there are many independent programming sequences from the
transport which are exactly the same as the ones in btusb.c about MediaTek
support [1] and btmtkuart.c. We can try to split the transport independent
Bluetooth setups on the advance, place them into the common files and allow
varous transport drivers to reuse them in the future.
[1] http://lists.infradead.org/pipermail/linux-mediatek/2019-January/017074.html
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Fri, 8 Mar 2019 01:15:43 +0000 (09:15 +0800)]
mmc: add SDIO identifiers for MediaTek Bluetooth devices
The SDIO identifier for MediaTek Bluetooth devices were defined in the
MediaTek Bluetooth driver. Moving the definitions in MMC header file
seems common sense.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Fainelli [Mon, 22 Apr 2019 16:46:44 +0000 (09:46 -0700)]
net: systemport: Remove need for DMA descriptor
All we do is write the length/status and address bits to a DMA
descriptor only to write its contents into on-chip registers right
after, eliminate this unnecessary step.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 22 Apr 2019 09:33:19 +0000 (09:33 +0000)]
bridge: Fix possible use-after-free when deleting bridge port
When a bridge port is being deleted, do not dereference it later in
br_vlan_port_event() as it can result in a use-after-free [1] if the RCU
callback was executed before invoking the function.
[1]
[ 129.638551] ==================================================================
[ 129.646904] BUG: KASAN: use-after-free in br_vlan_port_event+0x53c/0x5fd
[ 129.654406] Read of size 8 at addr
ffff8881e4aa1ae8 by task ip/483
[ 129.663008] CPU: 0 PID: 483 Comm: ip Not tainted
5.1.0-rc5-custom-02265-ga946bd73daac #1383
[ 129.672359] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016
[ 129.682484] Call Trace:
[ 129.685242] dump_stack+0xa9/0x10e
[ 129.689068] print_address_description.cold.2+0x9/0x25e
[ 129.694930] kasan_report.cold.3+0x78/0x9d
[ 129.704420] br_vlan_port_event+0x53c/0x5fd
[ 129.728300] br_device_event+0x2c7/0x7a0
[ 129.741505] notifier_call_chain+0xb5/0x1c0
[ 129.746202] rollback_registered_many+0x895/0xe90
[ 129.793119] unregister_netdevice_many+0x48/0x210
[ 129.803384] rtnl_delete_link+0xe1/0x140
[ 129.815906] rtnl_dellink+0x2a3/0x820
[ 129.844166] rtnetlink_rcv_msg+0x397/0x910
[ 129.868517] netlink_rcv_skb+0x137/0x3a0
[ 129.882013] netlink_unicast+0x49b/0x660
[ 129.900019] netlink_sendmsg+0x755/0xc90
[ 129.915758] ___sys_sendmsg+0x761/0x8e0
[ 129.966315] __sys_sendmsg+0xf0/0x1c0
[ 129.988918] do_syscall_64+0xa4/0x470
[ 129.993032] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 129.998696] RIP: 0033:0x7ff578104b58
...
[ 130.073811] Allocated by task 479:
[ 130.077633] __kasan_kmalloc.constprop.5+0xc1/0xd0
[ 130.083008] kmem_cache_alloc_trace+0x152/0x320
[ 130.088090] br_add_if+0x39c/0x1580
[ 130.092005] do_set_master+0x1aa/0x210
[ 130.096211] do_setlink+0x985/0x3100
[ 130.100224] __rtnl_newlink+0xc52/0x1380
[ 130.104625] rtnl_newlink+0x6b/0xa0
[ 130.108541] rtnetlink_rcv_msg+0x397/0x910
[ 130.113136] netlink_rcv_skb+0x137/0x3a0
[ 130.117538] netlink_unicast+0x49b/0x660
[ 130.121939] netlink_sendmsg+0x755/0xc90
[ 130.126340] ___sys_sendmsg+0x761/0x8e0
[ 130.130645] __sys_sendmsg+0xf0/0x1c0
[ 130.134753] do_syscall_64+0xa4/0x470
[ 130.138864] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 130.146195] Freed by task 0:
[ 130.149421] __kasan_slab_free+0x125/0x170
[ 130.154016] kfree+0xf3/0x310
[ 130.157349] kobject_put+0x1a8/0x4c0
[ 130.161363] rcu_core+0x859/0x19b0
[ 130.165175] __do_softirq+0x250/0xa26
[ 130.170956] The buggy address belongs to the object at
ffff8881e4aa1ae8
which belongs to the cache kmalloc-1k of size 1024
[ 130.184972] The buggy address is located 0 bytes inside of
1024-byte region [
ffff8881e4aa1ae8,
ffff8881e4aa1ee8)
Fixes:
9c0ec2e7182a ("bridge: support binding vlan dev link state to vlan member bridge ports")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Cc: Mike Manning <mmanning@vyatta.att-mail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Mike Manning <mmanning@vyatta.att-mail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Crag.Wang [Mon, 22 Apr 2019 05:03:43 +0000 (13:03 +0800)]
r8152: sync sa_family with the media type of network device
Without this patch the socket address family sporadically gets wrong
value ends up the dev_set_mac_address() fails to set the desired MAC
address.
Fixes:
25766271e42f ("r8152: Refresh MAC address during USBDEVFS_RESET")
Signed-off-by: Crag.Wang <crag.wang@dell.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-By: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 23 Apr 2019 05:09:33 +0000 (22:09 -0700)]
Merge branch 'mlxsw-Shared-buffer-improvements'
Ido Schimmel says:
====================
mlxsw: Shared buffer improvements
This patchset includes two improvements with regards to shared buffer
configuration in mlxsw.
The first part of this patchset forbids the user from performing illegal
shared buffer configuration that can result in unnecessary packet loss.
In order to better communicate these configuration failures to the user,
extack is propagated from devlink towards drivers. This is done in
patches #1-#8.
The second part of the patchset deals with the shared buffer
configuration of the CPU port. When a packet is trapped by the device,
it is sent across the PCI bus to the attached host CPU. From the
device's perspective, it is as if the packet is transmitted through the
CPU port.
While testing traffic directed at the CPU it became apparent that for
certain packet sizes and certain burst sizes, the current shared buffer
configuration of the CPU port is inadequate and results in packet drops.
The configuration is adjusted by patches #9-#14 that create two new pools
- ingress & egress - which are dedicated for CPU traffic.
====================
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 22 Apr 2019 12:08:56 +0000 (12:08 +0000)]
mlxsw: spectrum_buffers: Adjust CPU port shared buffer egress quotas
Switch the CPU port to use the new dedicated egress pool instead the
previously used egress pool which was shared with normal front panel
ports.
Add per-port quotas for the amount of traffic that can be buffered for
the CPU port and also adjust the per-{port, TC} quotas.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 22 Apr 2019 12:08:55 +0000 (12:08 +0000)]
mlxsw: spectrum_buffers: Allow skipping ingress port quota configuration
The CPU port is used to transmit traffic that is trapped to the host
CPU. It is therefore irrelevant to define ingress quota for it.
Add a 'skip_ingress' argument to the function tasked with configuring
per-port quotas, so that ingress quotas could be skipped in case the
passed local port is the CPU port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>