OSDN Git Service
Benjamin Tissoires [Fri, 28 Mar 2014 07:43:00 +0000 (00:43 -0700)]
Input: synaptics - add manual min/max quirk
The new Lenovo Haswell series (-40's) contains a new Synaptics touchpad.
However, these new Synaptics devices report bad axis ranges.
Under Windows, it is not a problem because the Windows driver uses RMI4
over SMBus to talk to the device. Under Linux, we are using the PS/2
fallback interface and it occurs the reported ranges are wrong.
Of course, it would be too easy to have only one range for the whole
series, each touchpad seems to be calibrated in a different way.
We can not use SMBus to get the actual range because I suspect the firmware
will switch into the SMBus mode and stop talking through PS/2 (this is the
case for hybrid HID over I2C / PS/2 Synaptics touchpads).
So as a temporary solution (until RMI4 land into upstream), start a new
list of quirks with the min/max manually set.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Hans de Goede [Wed, 26 Mar 2014 20:30:52 +0000 (13:30 -0700)]
Input: cypress_ps2 - don't report as a button pads
The cypress PS/2 trackpad models supported by the cypress_ps2 driver
emulate BTN_RIGHT events in firmware based on the finger position, as part
of this no motion events are sent when the finger is in the button area.
The INPUT_PROP_BUTTONPAD property is there to indicate to userspace that
BTN_RIGHT events should be emulated in userspace, which is not necessary
in this case.
When INPUT_PROP_BUTTONPAD is advertised userspace will wait for a motion
event before propagating the button event higher up the stack, as it needs
current abs x + y data for its BTN_RIGHT emulation. Since in the
cypress_ps2 pads don't report motion events in the button area, this means
that clicks in the button area end up being ignored, so
INPUT_PROP_BUTTONPAD actually causes problems for these touchpads, and
removing it fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=76341
Reported-by: Adam Williamson <awilliam@redhat.com>
Tested-by: Adam Williamson <awilliam@redhat.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Anthony Olech [Mon, 17 Feb 2014 19:23:39 +0000 (11:23 -0800)]
Input: da9052_onkey - use correct register bit for key status
The wrong register bit of the DA9052/3 PMIC registers was
used to determine the status on the ONKEY.
Also a failure in reading the status register will no longer
result in the work queue being rescheduled as that would result
in a (potentially) endless retry.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Acked-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Jean-Francois Dagenais [Wed, 12 Feb 2014 23:14:28 +0000 (15:14 -0800)]
Input: adp5588-keys - get value from data out when dir is out
As discussed here: http://ez.analog.com/message/35852, the 5587 revC and
5588 revB spec sheets contain a mistake in the GPIO_DAT_STATx register
description.
According to R.Shnell at ADI, as well as my own observations, it should
read: "GPIO data status (shows GPIO state when read for inputs)".
This commit changes the get value function accordingly.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry Torokhov [Thu, 23 Jan 2014 16:10:44 +0000 (08:10 -0800)]
Merge branch 'next' into for-linus
First round of input updates for 3.14.
Ping Cheng [Tue, 21 Jan 2014 04:18:04 +0000 (20:18 -0800)]
Input: wacom - add support for DTU-1031
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Ping Cheng [Fri, 17 Jan 2014 00:28:47 +0000 (16:28 -0800)]
Input: wacom - fix wacom->shared guards for dual input devices
features->quirks can have multiple bits set. For dual input, we only
need to check WACOM_QUIRK_MULTI_INPUT.
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Lothar Waßmann [Fri, 17 Jan 2014 00:26:55 +0000 (16:26 -0800)]
Input: edt_ft5x06 - use devm_* functions where appropriate
Simplify the error path and remove() function by using devm_*
functions for requesting gpios and irq and allocating the input
device.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
K. Y. Srinivasan [Sun, 12 Jan 2014 19:09:14 +0000 (11:09 -0800)]
Input: hyperv-keyboard - pass through 0xE1 prefix
Pass through the 0xE1 prefix so atkbd can properly parse the scancode
data.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Geert Uytterhoeven [Sun, 12 Jan 2014 19:08:49 +0000 (11:08 -0800)]
Input: logips2pp - fix spelling s/reciver/receiver/
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Paul Gortmaker [Mon, 6 Jan 2014 18:27:05 +0000 (10:27 -0800)]
Input: delete non-required instances of include <linux/init.h>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry Torokhov [Sat, 4 Jan 2014 08:52:48 +0000 (00:52 -0800)]
Input: twl4030-keypad - convert to using managed resources
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry Torokhov [Sat, 4 Jan 2014 08:08:49 +0000 (00:08 -0800)]
Input: twl6040-vibra - remove unneeded check for CONFIG_OF
Since the driver requires DT now we do not need to check if CONFIG_OF is
defined.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Sebastian Reichel [Sat, 4 Jan 2014 08:41:03 +0000 (00:41 -0800)]
Input: twl4030-keypad - add device tree support
Add device tree support for twl4030 keypad driver.
Tested on Nokia N900.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Libo Chen [Sat, 4 Jan 2014 08:00:30 +0000 (00:00 -0800)]
Input: twl6040-vibra - add missing of_node_put
We should drop reference to twl6040_core_node device_node once we are done
using it.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Libo Chen [Sat, 4 Jan 2014 07:58:32 +0000 (23:58 -0800)]
Input: twl4030-vibra - add missing of_node_put
We should drop reference to twl6040_core_node device_node once we are done
using it.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Mark Salter [Wed, 1 Jan 2014 19:34:39 +0000 (11:34 -0800)]
Input: i8042 - cleanup SERIO_I8042 dependencies
Remove messy dependencies from SERIO_I8042 by having it depend on one
Kconfig symbol (ARCH_MIGHT_HAVE_PC_SERIO) and having architectures
which need it select ARCH_MIGHT_HAVE_PC_SERIO in arch/*/Kconfig.
New architectures are unlikely to need SERIO_I8042, so this avoids
having an ever growing list of architectures to exclude.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Mark Salter [Wed, 1 Jan 2014 19:34:16 +0000 (11:34 -0800)]
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on x86
Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Mark Salter [Wed, 1 Jan 2014 19:33:53 +0000 (11:33 -0800)]
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on unicore32
Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Mark Salter [Wed, 1 Jan 2014 19:33:21 +0000 (11:33 -0800)]
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on sparc
Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Mark Salter [Wed, 1 Jan 2014 19:32:52 +0000 (11:32 -0800)]
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO for SH_CAYMAN
Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO. Cayman board
is only sh board which needs this.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Mark Salter [Wed, 1 Jan 2014 19:32:26 +0000 (11:32 -0800)]
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on powerpc
Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Mark Salter [Wed, 1 Jan 2014 19:32:00 +0000 (11:32 -0800)]
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on mips
Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Mark Salter [Wed, 1 Jan 2014 19:31:12 +0000 (11:31 -0800)]
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on IA64
Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Mark Salter [Wed, 1 Jan 2014 19:28:54 +0000 (11:28 -0800)]
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on ARM/Footbridge
Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Mark Salter [Wed, 1 Jan 2014 19:27:31 +0000 (11:27 -0800)]
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on alpha
Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Petr Sebor [Thu, 2 Jan 2014 23:35:07 +0000 (15:35 -0800)]
Input: xpad - add new USB IDs for Logitech F310 and F710
This enables the rumble force feedback on the F710 unit since
it is no longer treated as XTYPE_UNKNOWN type.
Signed-off-by: Petr Sebor <petr@scssoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Thomaz de Oliveira dos Reis [Thu, 2 Jan 2014 23:38:45 +0000 (15:38 -0800)]
Input: xpad - change D-PAD mapping on Razer devices
When using Razer Onza controller the dpad doesn't work in many games
because D-PAD was mapped to buttons (useful for dance pads) and not to
HAT0X/Y axis.
ers who really want to have it mapped to buttons can restore previous
behavior by using 'dpad_to_buttons' module option.
Signed-off-by: Thomaz de Oliveira dos Reis <thor27@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry Torokhov [Fri, 27 Dec 2013 01:44:29 +0000 (17:44 -0800)]
Input: allocate absinfo data when setting ABS capability
We need to make sure we allocate absinfo data when we are setting one of
EV_ABS/ABS_XXX capabilities, otherwise we may bomb when we try to emit this
event.
Rested-by: Paul Cercueil <pcercuei@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Doug Anderson [Mon, 30 Dec 2013 00:52:46 +0000 (16:52 -0800)]
Input: cros_ec_keyb - fix problems with backslash
The driver can't deal with two entries its keymap having the same keycode.
When this happens it will get confused about whether the key is down or up
and will cause some screwy behavior.
We need to have two entries for KEY_BACKSLASH to handle US and UK
keyboards. Specifically:
* On the US keyboard the backslash key (above enter) is r3 c11 and is
supposed to be reported as BACKSLASH.
* On the UK keyboard the # key (left of enter) is r4 c10 and is
supposed to be reported as BACKSLASH.
* On the UK keyboard the \ key (left of Z) is r2 c7 and is supposed to
be reported as KEY_102ND.
Note that both keyboards (US and UK) have only one physical backslash
key so the constraint that each physical key should have its own keycode
still stands.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Sachin Kamat [Sat, 28 Dec 2013 01:13:45 +0000 (17:13 -0800)]
Input: keypad-omap - cleanup header file
Commit
2203747c9771 ("ARM: omap: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Sachin Kamat [Sat, 28 Dec 2013 01:13:17 +0000 (17:13 -0800)]
Input: keypad-ep93xx - cleanup header file
Commit
a3b2924547a7 ("ARM: ep93xx: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry Torokhov [Sun, 15 Dec 2013 11:28:26 +0000 (03:28 -0800)]
Input: pmic8xxx-pwrkey - switch to using managed resources
This simplifies error handling and device removal paths.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wei Yongjun [Tue, 17 Dec 2013 17:03:05 +0000 (09:03 -0800)]
Input: pmic8xxx-pwrkey - pass correct device identity to free_irq()
free_irq() in the error handling case is missing when change
pass input device directly to interrupt.
Fixes:
b27f8fee4965('Input: pmic8xxx-pwrkey - pass input device directly to interrupt')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Yunkang Tang [Thu, 26 Dec 2013 22:54:19 +0000 (14:54 -0800)]
Input: ALPS - add support for "Dolphin" devices
This adds support for another flavor of ALPS protocol used in newer
"Dolphin" devices.
Signed-off-by: Yunkang Tang <yunkang.tang@cn.alps.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Antonio Ospite [Wed, 18 Dec 2013 16:39:10 +0000 (08:39 -0800)]
Input: fix typos in Documentation/input/gamepad.txt
Fix some typos and while at it also use "PS" as the name for the central
"HOME" button on Sony controllers, this is how Sony itself calls it.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wei Yongjun [Tue, 17 Dec 2013 16:58:18 +0000 (08:58 -0800)]
Input: zforce - fix error return code in zforce_start()
The error code was not set if unable to set config, so the error
condition wasn't reflected in the return value. Fix to return a
negative error code from the error handling case instead of 0.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Hans de Goede [Mon, 16 Dec 2013 15:09:25 +0000 (07:09 -0800)]
Input: elantech - improve clickpad detection
The current assumption in the elantech driver that hw version 3 touchpads
are never clickpads and hw version 4 touchpads are always clickpads is
wrong.
There are several bug reports for this, ie:
https://bugzilla.redhat.com/show_bug.cgi?id=
1030802
http://superuser.com/questions/619582/right-elantech-touchpad-button-not-working-in-linux
I've spend a couple of hours wading through various bugzillas, launchpads
and forum posts to create a list of fw-versions and capabilities for
different laptop models to find a good method to differentiate between
clickpads and versions with separate hardware buttons.
Which shows that a device being a clickpad is reliable indicated by bit 12
being set in the fw_version. I've included the gathered list inside the
driver, so that we've this info at hand if we need to revisit this later.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rafał Miłecki [Mon, 16 Dec 2013 05:00:48 +0000 (21:00 -0800)]
Input: define KEY_WWAN for Wireless WAN
Some devices with support for mobile networks may have buttons for
enabling/disabling such connection. An example can be Linksys router 54G3G.
We already have KEY_BLUETOOTH, KEY_WLAN and KEY_UWB so it makes sense to
add KEY_WWAN as well. As we already have KEY_WIMAX, use it's value for
KEY_WWAN and make it an alias.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Aleksej Makarov [Sat, 23 Nov 2013 18:20:36 +0000 (10:20 -0800)]
Input: don't call input_dev_release_keys() in resume
When waking up the platform by pressing a specific key, sending a
release on that key makes it impossible to react on the event in
user-space. This is fixed by moving the input_reset_device() call to
resume instead.
[dmitry.torokhov@gmail.com: make sure we still restore LED/sound state
after resume, handle hibernation properly]
Signed-off-by: Aleksej Makarov <aleksej.makarov@sonymobile.com>
Signed-off-by: Oskar Andero <oskar.andero@sonymobile.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Antonio Ospite [Mon, 16 Dec 2013 09:52:17 +0000 (01:52 -0800)]
Input: joystick - use sizeof(VARIABLE) in documentation
Use the preferred style sizeof(VARIABLE) instead of sizeof(TYPE) in the
joystick API documentation, Documentation/CodingStyle states that this
is the preferred style for allocations but using it elsewhere is good
too.
Also fix some errors like "sizeof(struct mybuffer)" which didn't mean
anything.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Antonio Ospite [Mon, 16 Dec 2013 09:51:47 +0000 (01:51 -0800)]
Input: joystick - refer to /dev/input/js0 in documentation
Nowadays the joystick device nodes are created under /dev/input, reflect
this in the documentation in order to make copy and paste easier for
users.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Guenter Roeck [Thu, 28 Nov 2013 04:08:33 +0000 (20:08 -0800)]
Input: ads7846 - convert to hwmon_device_register_with_groups()
Simplify the code and create mandatory 'name' attribute by using
new hwmon API.
Also use is_visible to determine visible attributes instead of creating
several different attribute groups.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Ping Cheng [Thu, 5 Dec 2013 20:54:53 +0000 (12:54 -0800)]
Input: wacom - add reporting of SW_MUTE_DEVICE events
New Intuos series models added a hardware switch to turn touch
data on/off. The state of the switch is reported periodically
from the tablet. To report the state the driver will emit SW_MUTE_DEVICE
events.
Reviewed_by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry Torokhov [Mon, 16 Dec 2013 10:04:49 +0000 (02:04 -0800)]
Merge tag 'v3.13-rc4' into next
Synchronize with mainline to bring in the new keycode definitions and
new hwmon API.
Linus Torvalds [Sun, 15 Dec 2013 20:31:33 +0000 (12:31 -0800)]
Linux 3.13-rc4
Matias Bjorling [Tue, 10 Dec 2013 15:50:38 +0000 (16:50 +0100)]
null_blk: mem garbage on NUMA systems during init
For NUMA systems, initializing the blk-mq layer and using per node hctx.
We initialize submit queues to 1, while blk-mq nr_hw_queues is
initialized to the number of NUMA nodes.
This makes the null_init_hctx function overwrite memory outside of what
it allocated. In my case it lead to writing garbage into struct
request_queue's mq_map.
Signed-off-by: Matias Bjorling <m@bjorling.me>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sergey Senozhatsky [Thu, 12 Dec 2013 23:25:57 +0000 (02:25 +0300)]
radeon_pm: fix oops in hwmon_attributes_visible() and radeon_hwmon_show_temp_thresh()
Since commit
ec39f64bba34 ("drm/radeon/dpm: Convert to use
devm_hwmon_register_with_groups") radeon_hwmon_init() is using
hwmon_device_register_with_groups(), which sets `rdev' as a device
private driver_data, while hwmon_attributes_visible() and
radeon_hwmon_show_temp_thresh() are still waiting for `drm_device'.
Fix them by using dev_get_drvdata(), in order to avoid this oops:
BUG: unable to handle kernel paging request at
0000000000001e28
IP: [<
ffffffffa02ae8b4>] hwmon_attributes_visible+0x18/0x3d [radeon]
PGD
15057e067 PUD
151a8e067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
Call Trace:
internal_create_group+0x114/0x1d9
sysfs_create_group+0xe/0x10
sysfs_create_groups+0x22/0x5f
device_add+0x34f/0x501
device_register+0x15/0x18
hwmon_device_register_with_groups+0xb5/0xed
radeon_hwmon_init+0x56/0x7c [radeon]
radeon_pm_init+0x134/0x7e5 [radeon]
radeon_modeset_init+0x75f/0x8ed [radeon]
radeon_driver_load_kms+0xc6/0x187 [radeon]
drm_dev_register+0xf9/0x1b4 [drm]
drm_get_pci_dev+0x98/0x129 [drm]
radeon_pci_probe+0xa3/0xac [radeon]
pci_device_probe+0x6e/0xcf
driver_probe_device+0x98/0x1c4
__driver_attach+0x5c/0x7e
bus_for_each_dev+0x7b/0x85
driver_attach+0x19/0x1b
bus_add_driver+0x104/0x1ce
driver_register+0x89/0xc5
__pci_register_driver+0x58/0x5b
drm_pci_init+0x86/0xea [drm]
radeon_init+0x97/0x1000 [radeon]
do_one_initcall+0x7f/0x117
load_module+0x1583/0x1bb4
SyS_init_module+0xa0/0xaf
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Alexander Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 15 Dec 2013 19:56:47 +0000 (11:56 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't
figure out why it breaks things.
2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it
was basically doing "x == x", from Dave Jones.
3) Freescale FEC driver was DMA mapping the wrong number of bytes, from
Sebastian Siewior.
4) Blackhole and prohibit routes in ipv6 were not doing the right thing
because their ->input and ->output methods were not being assigned
correctly. Now they behave properly like their ipv4 counterparts.
From Kamala R.
5) Several drivers advertise the NETIF_F_FRAGLIST capability, but
really do not support this feature and will send garbage packets if
fed fraglist SKBs. From Eric Dumazet.
6) Fix long standing user triggerable BUG_ON over loopback in RDS
protocol stack, from Venkat Venkatsubra.
7) Several not so common code paths can potentially try to invoke
packet scheduler actions that might be NULL without checking. Shore
things up by either 1) defining a method as mandatory and erroring
on registration if that method is NULL 2) defininig a method as
optional and the registration function hooks up a default
implementation when NULL is seen. From Jamal Hadi Salim.
8) Fix fragment detection in xen-natback driver, from Paul Durrant.
9) Kill dangling enter_memory_pressure method in cg_proto ops, from
Eric W Biederman.
10) SKBs that traverse namespaces should have their local_df cleared,
from Hannes Frederic Sowa.
11) IOCB file position is not being updated by macvtap_aio_read() and
tun_chr_aio_read(). From Zhi Yong Wu.
12) Don't free virtio_net netdev before releasing all of the NAPI
instances. From Andrey Vagin.
13) Procfs entry leak in xt_hashlimit, from Sergey Popovich.
14) IPv6 routes that are no cached routes should not count against the
garbage collection limits. We had this almost right, but were
missing handling addrconf generated routes properly. From Hannes
Frederic Sowa.
15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL
route info when they are called, from Stefan Tomanek.
16) TUN and MACVTAP have had truncated packet signalling for some time,
fix from Jason Wang.
17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet.
18) xen-netback does not interpret the NAPI budget properly for TX work,
fix from Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
xen-netback: fix gso_prefix check
net: make neigh_priv_len in struct net_device 16bit instead of 8bit
drivers: net: cpsw: fix for cpsw crash when build as modules
xen-netback: napi: don't prematurely request a tx event
xen-netback: napi: fix abuse of budget
sch_tbf: use do_div() for 64-bit divide
udp: ipv4: must add synchronization in udp_sk_rx_dst_set()
net:fec: remove duplicate lines in comment about errata ERR006358
Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature"
8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature
xen-netback: make sure skb linear area covers checksum field
net: smc91x: Fix device tree based configuration so it's usable
udp: ipv4: fix potential use after free in udp_v4_early_demux()
macvtap: signal truncated packets
tun: unbreak truncated packet signalling
net: sched: htb: fix the calculation of quantum
net: sched: tbf: fix the calculation of max_size
micrel: add support for KSZ8041RNLI
...
Linus Torvalds [Sun, 15 Dec 2013 19:52:47 +0000 (11:52 -0800)]
Merge branch 'x86/urgent' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"This is a pretty small batch:
The biggest single change is to stop using EFI time services on 32-bit
platforms. This matches our current behavior on 64-bit platforms as
we already had ruled them out there as being too unreliable. Turns
out that affects 32-bit platforms, too.
One NULL pointer fix for SGI UV.
Two minor build fixes, one of which only affects icc and the other
which affects icc and future versions or nonstandard default settings
of gcc"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Don't use (U)EFI time services on 32 bit
x86, build, icc: Remove uninitialized_var() from compiler-intel.h
x86/UV: Fix NULL pointer dereference in uv_flush_tlb_others() if the 'nobau' boot option is used
x86, build: Pass in additional -mno-mmx, -mno-sse options
Linus Torvalds [Sun, 15 Dec 2013 19:45:27 +0000 (11:45 -0800)]
Merge tag 'pci-v3.13-fixes-2' of git://git./linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI device hotplug
- Move device_del() from pci_stop_dev() to pci_destroy_dev() (Rafael
Wysocki)
Host bridge drivers
- Update maintainers for DesignWare, i.MX6, Armada, R-Car (Bjorn
Helgaas)
- mvebu: Return 'unsupported' for Interrupt Line and Interrupt Pin
(Jason Gunthorpe)
Miscellaneous
- Avoid unnecessary CPU switch when calling .probe() (Alexander
Duyck)
- Revert "workqueue: allow work_on_cpu() to be called recursively"
(Bjorn Helgaas)
- Disable Bus Master only on kexec reboot (Khalid Aziz)
- Omit PCI ID macro strings to shorten quirk names for LTO (Michal
Marek)"
* tag 'pci-v3.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Add DesignWare, i.MX6, Armada, R-Car PCI host maintainers
PCI: Disable Bus Master only on kexec reboot
PCI: mvebu: Return 'unsupported' for Interrupt Line and Interrupt Pin
PCI: Omit PCI ID macro strings to shorten quirk names
PCI: Move device_del() from pci_stop_dev() to pci_destroy_dev()
Revert "workqueue: allow work_on_cpu() to be called recursively"
PCI: Avoid unnecessary CPU switch when calling driver .probe() method
Linus Torvalds [Sun, 15 Dec 2013 19:28:02 +0000 (11:28 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/linux-security
Pull SELinux fixes from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: process labeled IPsec TCP SYN-ACK packets properly in selinux_ip_postroute()
selinux: look for IPsec labels on both inbound and outbound packets
selinux: handle TCP SYN-ACK packets correctly in selinux_ip_postroute()
selinux: handle TCP SYN-ACK packets correctly in selinux_ip_output()
selinux: fix possible memory leak
Linus Torvalds [Sun, 15 Dec 2013 19:17:45 +0000 (11:17 -0800)]
Revert "selinux: consider filesystem subtype in policies"
This reverts commit
102aefdda4d8275ce7d7100bc16c88c74272b260.
Tom London reports that it causes sync() to hang on Fedora rawhide:
https://bugzilla.redhat.com/show_bug.cgi?id=
1033965
and Josh Boyer bisected it down to this commit. Reverting the commit in
the rawhide kernel fixes the problem.
Eric Paris root-caused it to incorrect subtype matching in that commit
breaking fuse, and has a tentative patch, but by now we're better off
retrying this in 3.14 rather than playing with it any more.
Reported-by: Tom London <selinux@gmail.com>
Bisected-by: Josh Boyer <jwboyer@fedoraproject.org>
Acked-by: Eric Paris <eparis@redhat.com>
Cc: James Morris <jmorris@namei.org>
Cc: Anand Avati <avati@redhat.com>
Cc: Paul Moore <paul@paul-moore.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen Boyd [Sun, 15 Dec 2013 11:24:45 +0000 (03:24 -0800)]
Input: pmic8xxx-pwrkey - migrate to regmap APIs
Use the regmap APIs for this driver instead of custom pm8xxx
APIs. This breaks this driver's dependency on the pm8xxx APIs and
allows us to easily port it to other bus protocols in the future.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stephen Boyd [Sun, 15 Dec 2013 11:14:47 +0000 (03:14 -0800)]
Input: pmic8xxx-pwrkey - pass input device directly to interrupt
Instead of passing the pointer to the container structure just
pass the input device here. This saves a dereference in the fast
path.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stephen Boyd [Sun, 15 Dec 2013 11:46:21 +0000 (03:46 -0800)]
Input: pm8xxx-vibrator - migrate to regmap APIs
Use the regmap APIs for this driver instead of custom pm8xxx
APIs. This breaks this driver's dependency on the pm8xxx APIs and
allows us to easily port it to other bus protocols in the future.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stephen Boyd [Sun, 15 Dec 2013 11:43:06 +0000 (03:43 -0800)]
Input: pm8xxx-vibrator - switch to using managed resources
Simplify the error paths and reduce the lines of code in this
driver by using the devm_* APIs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rashika Kheria [Sun, 15 Dec 2013 10:25:55 +0000 (02:25 -0800)]
Input: cyttsp - include appropriate header file in cyttsp_i2c_common.c
Include cyttsp4_core.h in cyttsp_i2c_common.c to ensure that implementation
of cyttsp_i2c_read_block_data() and cyttsp_i2c_write_block_data()
match what the rest of the driver expects.
Thus, it also eliminates the following warning in cyttsp_i2c_common.c:
drivers/input/touchscreen/cyttsp_i2c_common.c:34:5: warning: no previous prototype for ‘cyttsp_i2c_read_block_data’ [-Wmissing-prototypes]
drivers/input/touchscreen/cyttsp_i2c_common.c:64:5: warning: no previous prototype for ‘cyttsp_i2c_write_block_data’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Heiko Stübner [Sat, 14 Dec 2013 09:41:55 +0000 (01:41 -0800)]
Input: zforce - fix possible driver hang during suspend
handle_level_irq masks the interrupt before handling it, and only
unmasks it after the handler is finished. So when a touch event
happens after threads are suspended, but before the system is fully asleep
the irq handler tries to wakeup the thread which will only happen on the
next resume, resulting in the wakeup event never being sent and the driver
not being able to wake the system from sleep due to the masked irq.
Therefore move the wakeup_event to a small non-threaded handler.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Carolyn Wyborny [Sat, 14 Dec 2013 11:26:46 +0000 (03:26 -0800)]
igb: Fix for issue where values could be too high for udelay function.
This patch changes the igb_phy_has_link function to check the value of the
parameter before deciding to use udelay or mdelay in order to be sure that
the value is not too high for udelay function.
CC: stable kernel <stable@vger.kernel.org> # 3.9+
Signed-off-by: Sunil K Pandey <sunil.k.pandey@intel.com>
Signed-off-by: Kevin B Smith <kevin.b.smith@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Sat, 14 Dec 2013 11:26:45 +0000 (03:26 -0800)]
i40e: fix null dereference
If the vsi->tx_rings structure is NULL we don't want to panic.
Change-Id: Ic694f043701738c434e8ebe0caf0673f4410dc10
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 14 Dec 2013 17:37:17 +0000 (09:37 -0800)]
Merge tag 'edac_fixes_for_3.13' of git://git./linux/kernel/git/bp/bp
Pull EDAC fix from Borislav Petkov:
"Silence a compiler warning in sb_edac"
* tag 'edac_fixes_for_3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
sb_edac: Shut up compiler warning when EDAC_DEBUG is enabled
Linus Torvalds [Sat, 14 Dec 2013 00:16:03 +0000 (16:16 -0800)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"This resolves some further issues with the dma mask changes on ARM
which have been found by TI and others, and also some corner cases
with the updates to the virtual to physical address translations.
Konstantin also found some problems with the unwinder, which now
performs tighter verification that the stack is valid while unwinding"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: fix asm/memory.h build error
ARM: 7917/1: cacheflush: correctly limit range of memory region being flushed
ARM: 7913/1: fix framepointer check in unwind_frame
ARM: 7912/1: check stack pointer in get_wchan
ARM: 7909/1: mm: Call setup_dma_zone() post early_paging_init()
ARM: 7908/1: mm: Fix the arm_dma_limit calculation
ARM: another fix for the DMA mapping checks
Linus Torvalds [Sat, 14 Dec 2013 00:14:39 +0000 (16:14 -0800)]
Merge tag 'arc-fixes-for-3.13' of git://git./linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"These are couple of weeks old already, but I just couldn't get them to
you earlier.
- couple of fixes for recently added perf code
- build time extable sort"
* tag 'arc-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [perf] Fix a few thinkos
ARC: Add guard macro to uapi/asm/unistd.h
ARC: extable: Enable sorting at build time
Linus Torvalds [Fri, 13 Dec 2013 21:22:22 +0000 (13:22 -0800)]
Merge tag 'dm-3.13-fixes' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"A set of device-mapper fixes for 3.13.
A fix for possible memory corruption during DM table load, fix a
possible leak of snapshot space in case of a crash, fix a possible
deadlock due to a shared workqueue in the delay target, fix to
initialize read-only module parameters that are used to export metrics
for dm stats and dm bufio.
Quite a few stable fixes were identified for both the thin-
provisioning and caching targets as a result of increased regression
testing using the device-mapper-test-suite (dmts). The most notable
of these are the reference counting fixes for the space map btree that
is used by the dm-array interface -- without these the dm-cache
metadata will leak, resulting in dm-cache devices running out of
metadata blocks. Also, some important fixes related to the
thin-provisioning target's transition to read-only mode on error"
* tag 'dm-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm array: fix a reference counting bug in shadow_ablock
dm space map: disallow decrementing a reference count below zero
dm stats: initialize read-only module parameter
dm bufio: initialize read-only module parameters
dm cache: actually resize cache
dm cache: update Documentation for invalidate_cblocks's range syntax
dm cache policy mq: fix promotions to occur as expected
dm thin: allow pool in read-only mode to transition to read-write mode
dm thin: re-establish read-only state when switching to fail mode
dm thin: always fallback the pool mode if commit fails
dm thin: switch to read-only mode if metadata space is exhausted
dm thin: switch to read only mode if a mapping insert fails
dm space map metadata: return on failure in sm_metadata_new_block
dm table: fail dm_table_create on dm_round_up overflow
dm snapshot: avoid snapshot space leak on crash
dm delay: fix a possible deadlock due to shared workqueue
Linus Torvalds [Fri, 13 Dec 2013 21:21:28 +0000 (13:21 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- Genius Gx Imperator Keyboard regression fix (missing break in case),
by Ben Hutchings
- duplicate sysfs entry error fix for hid-sensor-hub driver, by
Srinivas Pandruvada
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hid-sensor-hub: fix duplicate sysfs entry error
HID: kye: Fix missing break in kye_report_fixup()
Russell King [Tue, 10 Dec 2013 19:21:08 +0000 (19:21 +0000)]
ARM: fix asm/memory.h build error
Jason Gunthorpe reports a build failure when ARM_PATCH_PHYS_VIRT is
not defined:
In file included from arch/arm/include/asm/page.h:163:0,
from include/linux/mm_types.h:16,
from include/linux/sched.h:24,
from arch/arm/kernel/asm-offsets.c:13:
arch/arm/include/asm/memory.h: In function '__virt_to_phys':
arch/arm/include/asm/memory.h:244:40: error: 'PHYS_OFFSET' undeclared (first use in this function)
arch/arm/include/asm/memory.h:244:40: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/include/asm/memory.h: In function '__phys_to_virt':
arch/arm/include/asm/memory.h:249:13: error: 'PHYS_OFFSET' undeclared (first use in this function)
Fixes:
ca5a45c06cd4 ("ARM: mm: use phys_addr_t appropriately in p2v and v2p conversions")
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Fri, 13 Dec 2013 19:39:54 +0000 (11:39 -0800)]
Merge tag 'regulator-v3.13-rc3' of git://git./linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A small set of driver fixes plus one larger core change which changes
the way we check to see if we're using DT so that there aren't any
races between deciding we're using DT and the regulator subsystem
noticing.
This makes the new support for substituting a dummy regulator and
optional regulators work a lot better on DT systems since it ensures
that we don't trigger probe deferral when we shouldn't which was
causing bugs in clients"
* tag 'regulator-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: pfuze100: allow misprogrammed ID
regulator: pfuze100: Fix address of FABID
regulator: as3722: set the correct current limit
regulator: core: Check for DT every time we check full constraints
regulator: core: Replace checks of have_full_constraints with a function
Linus Torvalds [Fri, 13 Dec 2013 19:38:35 +0000 (11:38 -0800)]
Merge tag 'regmap-v3.13-rc3' of git://git./linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Two small changes to fix some error handling and checking (both of
which would be quite serious if the errors trigger) plus a trivial
documentation fix"
* tag 'regmap-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: use IS_ERR() to check clk_get() results
regmap: make sure we unlock on failure in regmap_bulk_write
regmap: trivial comment fix (copy'n'paste error)
Linus Torvalds [Fri, 13 Dec 2013 19:37:57 +0000 (11:37 -0800)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here are two simple but wanted fixes for the i2c subsystem"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: imx: Check the return value from clk_prepare_enable()
i2c: mux: Inherit retry count and timeout from parent for muxed bus
Linus Torvalds [Fri, 13 Dec 2013 19:31:22 +0000 (11:31 -0800)]
Merge tag 'for-linus-
20131212' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Two MTD fixes, for the pxa3xx-nand driver:
- This driver was not ready to fully Armada 370 NAND, with
particularly notable problems seen on flash with 2KB page sizes.
This "compatible" entry really should have been held back until
3.14 or later.
- Fix a bug seen in rare cases on the error path of a failed probe
attempt, where we free unallocated DMA resources"
* tag 'for-linus-
20131212' of git://git.infradead.org/linux-mtd:
mtd: nand: pxa3xx: Use info->use_dma to release DMA resources
Partially revert "mtd: nand: pxa3xx: Introduce 'marvell,armada370-nand' compatible string"
Linus Torvalds [Fri, 13 Dec 2013 19:29:51 +0000 (11:29 -0800)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"Here is the common fixes PULL for dmaengine.
Dan has been working on fixing the build issues in bunch of drivers.
Here we have one fixing s3c24xx-dma, along with fix from Russell on
pl08x. Also we have Kuninori rcar dma fixes. The s3c24xx-dma which
was added in last merge window missed updates to usage of DMA_COMPLETE
so converting the last driver"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: fix build breakage in s3c24xx-dma
Fix pl08x warnings
rcar-hpbdma: initialise plane information when halted
rcar-hpbdma: fixup channel busy check for double plane
rcar-hpbdma: add max transfer size
dma: mmp_pdma: add missing platform_set_drvdata() in mmp_pdma_probe()
dmaengine: s3c24xx-dma: use DMA_COMPLETE for dma completion status
Joe Thornber [Fri, 13 Dec 2013 14:55:55 +0000 (14:55 +0000)]
dm array: fix a reference counting bug in shadow_ablock
An old array block could have its reference count decremented below
zero when it is being replaced in the btree by a new array block.
The fix is to increment the old ablock's reference count just before
inserting a new ablock into the btree.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.9+
Joe Thornber [Fri, 13 Dec 2013 12:31:08 +0000 (12:31 +0000)]
dm space map: disallow decrementing a reference count below zero
The old behaviour, returning -EINVAL if a ref_count of 0 would be
decremented, was removed in commit
f722063 ("dm space map: optimise
sm_ll_dec and sm_ll_inc"). To fix this regression we return an error
code from the mutator function pointer passed to sm_ll_mutate() and have
dec_ref_count() return -EINVAL if the old ref_count is 0.
Add a DMERR to reflect the potential seriousness of this error.
Also, add missing dm_tm_unlock() to sm_ll_mutate()'s error path.
With this fix the following dmts regression test now passes:
dmtest run --suite cache -n /metadata_use_kernel/
The next patch fixes the higher-level dm-array code that exposed this
regression.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.12+
Mark Brown [Fri, 13 Dec 2013 13:44:57 +0000 (13:44 +0000)]
Merge remote-tracking branch 'regulator/topic/constraints' into regulator-linus
James Morris [Fri, 13 Dec 2013 02:27:55 +0000 (13:27 +1100)]
Merge branch 'master' of git://git.infradead.org/users/pcmoore/selinux_fixes into for-linus
Linus Torvalds [Fri, 13 Dec 2013 02:22:10 +0000 (18:22 -0800)]
Merge branch 'akpm' (fixes from Andrew)
Merge patches from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: memcg: do not allow task about to OOM kill to bypass the limit
mm: memcg: fix race condition between memcg teardown and swapin
thp: move preallocated PTE page table on move_huge_pmd()
mfd/rtc: s5m: fix register updating by adding regmap for RTC
rtc: s5m: enable IRQ wake during suspend
rtc: s5m: limit endless loop waiting for register update
rtc: s5m: fix unsuccesful IRQ request during probe
drivers/rtc/rtc-s5m.c: fix info->rtc assignment
include/linux/kernel.h: make might_fault() a nop for !MMU
drivers/rtc/rtc-at91rm9200.c: correct alarm over day/month wrap
procfs: also fix proc_reg_get_unmapped_area() for !MMU case
mm: memcg: do not declare OOM from __GFP_NOFAIL allocations
include/linux/hugetlb.h: make isolate_huge_page() an inline
Johannes Weiner [Fri, 13 Dec 2013 01:12:35 +0000 (17:12 -0800)]
mm: memcg: do not allow task about to OOM kill to bypass the limit
Commit
4942642080ea ("mm: memcg: handle non-error OOM situations more
gracefully") allowed tasks that already entered a memcg OOM condition to
bypass the memcg limit on subsequent allocation attempts hoping this
would expedite finishing the page fault and executing the kill.
David Rientjes is worried that this breaks memcg isolation guarantees
and since there is no evidence that the bypass actually speeds up fault
processing just change it so that these subsequent charge attempts fail
outright. The notable exception being __GFP_NOFAIL charges which are
required to bypass the limit regardless.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-bt: David Rientjes <rientjes@google.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 13 Dec 2013 01:12:34 +0000 (17:12 -0800)]
mm: memcg: fix race condition between memcg teardown and swapin
There is a race condition between a memcg being torn down and a swapin
triggered from a different memcg of a page that was recorded to belong
to the exiting memcg on swapout (with CONFIG_MEMCG_SWAP extension). The
result is unreclaimable pages pointing to dead memcgs, which can lead to
anything from endless loops in later memcg teardown (the page is charged
to all hierarchical parents but is not on any LRU list) or crashes from
following the dangling memcg pointer.
Memcgs with tasks in them can not be torn down and usually charges don't
show up in memcgs without tasks. Swapin with the CONFIG_MEMCG_SWAP
extension is the notable exception because it charges the cgroup that
was recorded as owner during swapout, which may be empty and in the
process of being torn down when a task in another memcg triggers the
swapin:
teardown: swapin:
lookup_swap_cgroup_id()
rcu_read_lock()
mem_cgroup_lookup()
css_tryget()
rcu_read_unlock()
disable css_tryget()
call_rcu()
offline_css()
reparent_charges()
res_counter_charge() (hierarchical!)
css_put()
css_free()
pc->mem_cgroup = dead memcg
add page to dead lru
Add a final reparenting step into css_free() to make sure any such raced
charges are moved out of the memcg before it's finally freed.
In the longer term it would be cleaner to have the css_tryget() and the
res_counter charge under the same RCU lock section so that the charge
reparenting is deferred until the last charge whose tryget succeeded is
visible. But this will require more invasive changes that will be
harder to evaluate and backport into stable, so better defer them to a
separate change set.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kirill A. Shutemov [Fri, 13 Dec 2013 01:12:33 +0000 (17:12 -0800)]
thp: move preallocated PTE page table on move_huge_pmd()
Andrey Wagin reported crash on VM_BUG_ON() in pgtable_pmd_page_dtor() with
fallowing backtrace:
free_pgd_range+0x2bf/0x410
free_pgtables+0xce/0x120
unmap_region+0xe0/0x120
do_munmap+0x249/0x360
move_vma+0x144/0x270
SyS_mremap+0x3b9/0x510
system_call_fastpath+0x16/0x1b
The crash can be reproduce with this test case:
#define _GNU_SOURCE
#include <sys/mman.h>
#include <stdio.h>
#include <unistd.h>
#define MB (1024 * 1024UL)
#define GB (1024 * MB)
int main(int argc, char **argv)
{
char *p;
int i;
p = mmap((void *) GB, 10 * MB, PROT_READ | PROT_WRITE,
MAP_PRIVATE | MAP_ANONYMOUS | MAP_FIXED, -1, 0);
for (i = 0; i < 10 * MB; i += 4096)
p[i] = 1;
mremap(p, 10 * MB, 10 * MB, MREMAP_FIXED | MREMAP_MAYMOVE, 2 * GB);
return 0;
}
Due to split PMD lock, we now store preallocated PTE tables for THP
pages per-PMD table. It means we need to move them to other PMD table
if huge PMD moved there.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Andrey Vagin <avagin@openvz.org>
Tested-by: Andrey Vagin <avagin@openvz.org>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Kozlowski [Fri, 13 Dec 2013 01:12:31 +0000 (17:12 -0800)]
mfd/rtc: s5m: fix register updating by adding regmap for RTC
Rename old regmap field of "struct sec_pmic_dev" to "regmap_pmic" and
add new regmap for RTC.
On S5M8767A registers were not properly updated and read due to usage of
the same regmap as the PMIC. This could be observed in various hangs,
e.g. in infinite loop during waiting for UDR field change.
On this chip family the RTC has different I2C address than PMIC so
additional regmap is needed.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Kozlowski [Fri, 13 Dec 2013 01:12:30 +0000 (17:12 -0800)]
rtc: s5m: enable IRQ wake during suspend
Add PM suspend/resume ops to rtc-s5m driver and enable IRQ wake during
suspend so the RTC would act like a wake up source. This allows waking
up from suspend to RAM on RTC alarm interrupt.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Kozlowski [Fri, 13 Dec 2013 01:12:28 +0000 (17:12 -0800)]
rtc: s5m: limit endless loop waiting for register update
After setting alarm or time the driver is waiting for UDR register to be
cleared indicating that registers data have been transferred.
Limit the endless loop to only 5 retries.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Kozlowski [Fri, 13 Dec 2013 01:12:26 +0000 (17:12 -0800)]
rtc: s5m: fix unsuccesful IRQ request during probe
Probe failed for rtc-s5m:
s5m-rtc s5m-rtc: Failed to request alarm IRQ: 12: -22
s5m-rtc: probe of s5m-rtc failed with error -22
Fix rtc-s5m interrupt request by using regmap_irq_get_virq() for mapping
the IRQ.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Fri, 13 Dec 2013 01:12:25 +0000 (17:12 -0800)]
drivers/rtc/rtc-s5m.c: fix info->rtc assignment
Fix this warning:
drivers/rtc/rtc-s5m.c: In function `s5m_rtc_probe':
drivers/rtc/rtc-s5m.c:545: warning: assignment from incompatible pointer type
struct s5m_rtc_info.rtc has type "struct regmap *", while
struct sec_pmic_dev.rtc has type "struct i2c_client *".
Probably the author wanted to assign "struct sec_pmic_dev.regmap", which
has the correct type.
Also, as "rtc" doesn't make much sense as a name for a regmap, rename it
to "regmap".
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Axel Lin [Fri, 13 Dec 2013 01:12:24 +0000 (17:12 -0800)]
include/linux/kernel.h: make might_fault() a nop for !MMU
The machine cannot fault if !MUU, so make might_fault() a nop for !MMU.
This fixes below build error if
!CONFIG_MMU && (CONFIG_PROVE_LOCKING=y || CONFIG_DEBUG_ATOMIC_SLEEP=y):
arch/arm/kernel/built-in.o: In function `arch_ptrace':
arch/arm/kernel/ptrace.c:852: undefined reference to `might_fault'
arch/arm/kernel/built-in.o: In function `restore_sigframe':
arch/arm/kernel/signal.c:173: undefined reference to `might_fault'
...
arch/arm/kernel/built-in.o:arch/arm/kernel/signal.c:177: more undefined references to `might_fault' follow
make: *** [vmlinux] Error 1
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Pizunski [Fri, 13 Dec 2013 01:12:23 +0000 (17:12 -0800)]
drivers/rtc/rtc-at91rm9200.c: correct alarm over day/month wrap
Update month and day of month to the alarm month/day instead of current
day/month when setting the RTC alarm mask.
Signed-off-by: Linus Pizunski <linus@narrativeteam.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Beulich [Fri, 13 Dec 2013 01:12:22 +0000 (17:12 -0800)]
procfs: also fix proc_reg_get_unmapped_area() for !MMU case
Commit
fad1a86e25e0 ("procfs: call default get_unmapped_area on
MMU-present architectures"), as its title says, took care of only the
MMU case, leaving the !MMU side still in the regressed state (returning
-EIO in all cases where pde->proc_fops->get_unmapped_area is NULL).
From the
fad1a86e25e0 changelog:
"Commit
c4fe24485729 ("sparc: fix PCI device proc file mmap(2)") added
proc_reg_get_unmapped_area in proc_reg_file_ops and
proc_reg_file_ops_no_compat, by which now mmap always returns EIO if
get_unmapped_area method is not defined for the target procfs file, which
causes regression of mmap on /proc/vmcore.
To address this issue, like get_unmapped_area(), call default
current->mm->get_unmapped_area on MMU-present architectures if
pde->proc_fops->get_unmapped_area, i.e. the one in actual file operation
in the procfs file, is not defined"
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org> [3.12.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 13 Dec 2013 01:12:20 +0000 (17:12 -0800)]
mm: memcg: do not declare OOM from __GFP_NOFAIL allocations
Commit
84235de394d9 ("fs: buffer: move allocation failure loop into the
allocator") started recognizing __GFP_NOFAIL in memory cgroups but
forgot to disable the OOM killer.
Any task that does not fail allocation will also not enter the OOM
completion path. So don't declare an OOM state in this case or it'll be
leaked and the task be able to bypass the limit until the next
userspace-triggered page fault cleans up the OOM state.
Reported-by: William Dauchy <wdauchy@gmail.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: <stable@vger.kernel.org> [3.12.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Naoya Horiguchi [Fri, 13 Dec 2013 01:12:19 +0000 (17:12 -0800)]
include/linux/hugetlb.h: make isolate_huge_page() an inline
With CONFIG_HUGETLBFS=n:
mm/migrate.c: In function `do_move_page_to_node_array':
include/linux/hugetlb.h:140:33: warning: statement with no effect [-Wunused-value]
#define isolate_huge_page(p, l) false
^
mm/migrate.c:1170:4: note: in expansion of macro `isolate_huge_page'
isolate_huge_page(page, &pagelist);
Reported-by: Borislav Petkov <bp@alien8.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 12 Dec 2013 23:46:06 +0000 (15:46 -0800)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Four security fixes for KVM on x86. Thanks to Andrew Honig and Lars
Bull from Google for reporting them"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: fix guest-initiated crash with x2apic (CVE-2013-6376)
KVM: x86: Convert vapic synchronization to _cached functions (CVE-2013-6368)
KVM: x86: Fix potential divide by 0 in lapic (CVE-2013-6367)
KVM: Improve create VCPU parameter (CVE-2013-4587)
Linus Torvalds [Thu, 12 Dec 2013 23:45:03 +0000 (15:45 -0800)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another batch of fixes.
Again, OMAP regressions due to move to DT is the bulk of the changes
here, but this should be the last of it for 3.13. There are also a
handful of OMAP hwmod changes (power management, reset handling) for
USB on OMAP3 that fixes some longish-standing bugs around USB resets.
There are a couple of other changes that also add up line count a bit:
One is a long-standing bug with the keyboard layout on one of the PXA
platforms. The other is a fix for highbank that moves their
power-off/reset button handling to be done in-kernel since relying on
userspace to handle it was fragile and awkward"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: sun6i: dt: Fix interrupt trigger types
ARM: sun7i: dt: Fix interrupt trigger types
MAINTAINERS: merge IMX6 entry into IMX
ARM: tegra: add missing break to fuse initialization code
ARM: pxa: prevent PXA270 occasional reboot freezes
ARM: pxa: tosa: fix keys mapping
ARM: OMAP2+: omap_device: add fail hook for runtime_pm when bad data is detected
ARM: OMAP2+: hwmod: Fix usage of invalid iclk / oclk when clock node is not present
ARM: OMAP3: hwmod data: Don't prevent RESET of USB Host module
ARM: OMAP2+: hwmod: Fix SOFTRESET logic
ARM: OMAP4+: hwmod data: Don't prevent RESET of USB Host module
ARM: dts: Fix booting for secure omaps
ARM: OMAP2+: Fix the machine entry for am3517
ARM: dts: Fix missing entries for am3517
ARM: OMAP2+: Fix overwriting hwmod data with data from device tree
ARM: davinci: Fix McASP mem resource names
ARM: highbank: handle soft poweroff and reset key events
ARM: davinci: fix number of resources passed to davinci_gpio_register()
gpio: davinci: fix check for unbanked gpio
Linus Torvalds [Thu, 12 Dec 2013 23:25:10 +0000 (15:25 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This is a small collection of fixes. It was rebased this morning, but
I was just fixing signed-off-by tags with the wrong email"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix access_ok() check in btrfs_ioctl_send()
Btrfs: make sure we cleanup all reloc roots if error happens
Btrfs: skip building backref tree for uuid and quota tree when doing balance relocation
Btrfs: fix an oops when doing balance relocation
Btrfs: don't miss skinny extent items on delayed ref head contention
btrfs: call mnt_drop_write after interrupted subvol deletion
Btrfs: don't clear the default compression type
Linus Torvalds [Thu, 12 Dec 2013 23:24:32 +0000 (15:24 -0800)]
Merge branch 'for-3.13' of git://linux-nfs.org/~bfields/linux
Pull nfsd reply cache bugfix from Bruce Fields:
"One bugfix for nfsd crashes"
* 'for-3.13' of git://linux-nfs.org/~bfields/linux:
nfsd: when reusing an existing repcache entry, unhash it first
Ezequiel Garcia [Tue, 10 Dec 2013 12:57:15 +0000 (09:57 -0300)]
mtd: nand: pxa3xx: Use info->use_dma to release DMA resources
In commit:
commit
62e8b851783138a11da63285be0fbf69530ff73d
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date: Fri Oct 4 15:30:38 2013 -0300
mtd: nand: pxa3xx: Allocate data buffer on detected flash size
the way the buffer is allocated was changed: the first READ_ID is issued
with a small kmalloc'ed buffer. Only once the flash page size is detected
the DMA buffers are allocated, and info->use_dma is set.
Currently, if the device detection fails, the driver checks the 'use_dma'
module parameter and tries to release unallocated DMA resources.
Fix this by checking the proper indicator of the DMA allocation, which
is 'info->use_dma'.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Ezequiel Garcia [Mon, 9 Dec 2013 21:36:26 +0000 (18:36 -0300)]
Partially revert "mtd: nand: pxa3xx: Introduce 'marvell,armada370-nand' compatible string"
This partially reverts
c0f3b8643a6fa2461d70760ec49d21d2b031d611.
The "armada370-nand" compatible support is not complete, and it was mistake
to add it. Revert it and postpone the support until the infrastructure is
in place.
Cc: <stable@vger.kernel.org> # 3.12
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Paul Moore [Tue, 10 Dec 2013 19:58:01 +0000 (14:58 -0500)]
selinux: process labeled IPsec TCP SYN-ACK packets properly in selinux_ip_postroute()
Due to difficulty in arriving at the proper security label for
TCP SYN-ACK packets in selinux_ip_postroute(), we need to check packets
while/before they are undergoing XFRM transforms instead of waiting
until afterwards so that we can determine the correct security label.
Reported-by: Janak Desai <Janak.Desai@gtri.gatech.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Moore <pmoore@redhat.com>
Paul Moore [Tue, 10 Dec 2013 19:57:54 +0000 (14:57 -0500)]
selinux: look for IPsec labels on both inbound and outbound packets
Previously selinux_skb_peerlbl_sid() would only check for labeled
IPsec security labels on inbound packets, this patch enables it to
check both inbound and outbound traffic for labeled IPsec security
labels.
Reported-by: Janak Desai <Janak.Desai@gtri.gatech.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Moore <pmoore@redhat.com>
Paul Moore [Wed, 4 Dec 2013 21:10:51 +0000 (16:10 -0500)]
selinux: handle TCP SYN-ACK packets correctly in selinux_ip_postroute()
In selinux_ip_postroute() we perform access checks based on the
packet's security label. For locally generated traffic we get the
packet's security label from the associated socket; this works in all
cases except for TCP SYN-ACK packets. In the case of SYN-ACK packet's
the correct security label is stored in the connection's request_sock,
not the server's socket. Unfortunately, at the point in time when
selinux_ip_postroute() is called we can't query the request_sock
directly, we need to recreate the label using the same logic that
originally labeled the associated request_sock.
See the inline comments for more explanation.
Reported-by: Janak Desai <Janak.Desai@gtri.gatech.edu>
Tested-by: Janak Desai <Janak.Desai@gtri.gatech.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Moore <pmoore@redhat.com>
Paul Moore [Wed, 4 Dec 2013 21:10:45 +0000 (16:10 -0500)]
selinux: handle TCP SYN-ACK packets correctly in selinux_ip_output()
In selinux_ip_output() we always label packets based on the parent
socket. While this approach works in almost all cases, it doesn't
work in the case of TCP SYN-ACK packets when the correct label is not
the label of the parent socket, but rather the label of the larval
socket represented by the request_sock struct.
Unfortunately, since the request_sock isn't queued on the parent
socket until *after* the SYN-ACK packet is sent, we can't lookup the
request_sock to determine the correct label for the packet; at this
point in time the best we can do is simply pass/NF_ACCEPT the packet.
It must be said that simply passing the packet without any explicit
labeling action, while far from ideal, is not terrible as the SYN-ACK
packet will inherit any IP option based labeling from the initial
connection request so the label *should* be correct and all our
access controls remain in place so we shouldn't have to worry about
information leaks.
Reported-by: Janak Desai <Janak.Desai@gtri.gatech.edu>
Tested-by: Janak Desai <Janak.Desai@gtri.gatech.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Moore <pmoore@redhat.com>