scsi: aacraid: Include HBA direct interface

Added support to send direct pasthru srb commands from management utilty
to the  controller.

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Dave Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Added support for hotplug

Added support for drive hotplug add and removal

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Dave Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Added support to set QD of attached drives

Added support to set qd of drives in slave_configure.This only works for
HBA1000 attached drives.

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Dave Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Retrieve Queue Depth from Adapter FW

Retrieved queue depth from fw and saved it for future use.
Only applicable for HBA1000 drives.

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Dave Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Added support for periodic wellness sync

This patch adds a new functions that periodically sync the time of host
to the adapter. In addition also informs the adapter that the driver is
alive and kicking. Only applicable to the HBA1000 and SMARTIOC2000.

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Dave Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Reworked aac_command_thread

Reworked aac_command_thread into aac_process_events

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Dave Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Added support for read medium error

This patch processes Raw IO read medium errors.

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Dave Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Added support for response path

This patch enables the driver to actually process the I/O, or srb replies
from adapter. In addition to any HBA1000 or SmartIOC2000 adapter events.

Signed-off-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@microsemi.com>
Signed-off-by: Dave Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Process Error for response I/O

Make sure that the driver processes error conditions even in the fast
response path for response from the adapter.

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Dave Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Reworked scsi command submission path

Moved the READ and WRITE switch cases to the top. Added a  default
case to the switch case and replaced duplicate scsi result value with a
macro.

The idea is that since most of scsi commands we care about performance
wise are read or write, we need to process them first.

Internally the compiler (GCC) converts a switch case into either a jump
table or a bunch of if else conditions, so placing the often used read,
write cases at the top is an effort in optimization.

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Dave Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Retrieve and update the device types

This patch adds support to retrieve the type of each adapter connected
device. Applicable to HBA1000 and SmartIOC2000 products

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Dave Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Added sa firmware support

sa_firmware adds the capability to differentiate the new SmartIOC family
of adapters from the series 8 and below.

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Dave Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: added support for init_struct_8

This  patch lays the groundwork for supporting the new HBA-1000 controller
family.A new INIT structure INIT_STRUCT_8 has been added which allows for a
variable size for MSI-x vectors among other things,  and is used for both
Series-8, HBA-1000 and SmartIOC-2000.

Signed-off-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@microsemi.com>
Signed-off-by: Dave Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Added aacraid.h include guard

Added aacraid.h include guard

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Dave Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Remove duplicate irq management code

Removed duplicate code that for acquiring and releasing irqs

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Dave Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: scsi_debug: Add OPTIMAL TRANSFER LENGTH GRANULARITY option.

[mkp: whitespace fixes]

Signed-off-by: Lukas Herbolt <lherbolt@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Updating driver version to v15.100.00.00

Updated driver version to "15.100.00.00"

Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Fix Firmware fault state 0x2100 during heavy 4K RR FIO stress test.

Due existence of loop in the IO path our HBA will receive heavy IOs and
also as driver is not updating the Reply Post Host Index frequently, So
there will be a high chance that our Firmware unable to find any free
entry in the Reply Post Descriptor Queue (i.e. Queue overflow occurs)
and can observe 0x2100 firmware fault.  So to fix this, we have defined
a thresh hold value. After continuously processing this thresh hold
number of reply descriptors driver will update the Reply Descriptor Host
Index so that this thresh hold number of reply descriptors entries will
be freed and these entries will be available for firmware and we won't
observe this Firmware fault. We have defined this threshold value as
1/3rd of the hba queue depth.

Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Fix for Crusader to achieve product targets with SAS devices.

Small glitch/degraded performance in Crusader is improved with SAS
drives by removing unnecessary spinlocks while clearing scsi command in
drivers internal lookup table.

Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Added print to notify cable running at a degraded speed.

Driver processes the event MPI26_EVENT_ACTIVE_CABLE_DEGRADED when a
cable is present and is running at a degraded speed (below the SAS3 12
Gb/s rate). Prints added to inform the user that the cable is not
running at optimal speed.

Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: remove coalescing settings for ioaccel2

- Setting coalescing has a significant negative impact on low
  queue-depth performance.
- Does not help high queue-depth performance.

Signed-off-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: storvsc: remove bogus code to transfer struct scatterlist

Remove a piece of code in storvsc_queuecommand that tries to pass the
physical address of the kernel struct scatterlist pointer to the host.

Fortunately the code can't ever be reached anyway.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: atari_scsi: Reset DMA during bus reset only under ST-DMA lock

The atari_scsi driver should not access Falcon DMA chip registers unless
it has acquired exclusive access to that chip. If the driver doesn't
have exclusive access then there's no need for a DMA reset as there are
no scsi commands in progress.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ncr5380: Improve target selection robustness

Handle timeout or bus phase change errors that could occur when sending
the IDENTIFY message.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ncr5380: Resolve various static checker warnings

Avoid various warnings from "make C=1" by annotating a couple of
unlock-then-lock sequences, replacing a zero with NULL and correcting
some type casts.

Also avoid a warning from "make W=1" by adding braces.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ncr5380: Reduce #include files

The NCR5380 wrapper drivers don't export symbols or declarations and
don't actually need separate header files. Most of these header files
were removed already; only sun3_scsi.h and g_NCR5380.h remain.

Move the remaining definitions to the corresponding .c files to improve
readability and proximity. The #defines which influence the #included
core driver are no longer mixed up with unrelated #defines and #includes.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ncr5380: Clean up dead code and redundant macro usage

Remove dead code inside #if 0 conditionals.

Remove the #ifdef __KERNEL__ test, since NCR5380.h has no definitions
that relate to userspace code.

Remove two redundant macro definitions which were overlooked in
commit e9db3198e08b ("sun3_scsi: Adopt NCR5380.c core driver").

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ncr5380: Shorten host info string by removing unused option macros

The DIFFERENTIAL and PARITY option macros are unused: no supported
hardware uses differential signalling and the core driver never
implemented parity checking. These options just waste space in the host
info string.

While we are here, fix a typo in the NCR5380_info() kernel-doc comment.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: decrease running_req in hisi_sas_slot_task_free()

There is an issue that hisi_sas_dev.running_req is not
decremented properly for internal abort and TMF.

To resolve, only decrease running_req in hisi_sas_slot_task_free()

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: fix probe ordering problem

There is a potential probe issue in how we trigger the hw initialisation.
Although we use 1s timer to delay hw initialisation, there is still a
potential that sas_register_ha() is not be finished before we start
the PHY init from hw->hw_init().
To avoid this issue, initialise the hw after sas_register_ha() in the
same probe context.
Note: it is not necessary to use 1s timer now (modified v2 hw only).

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: downgrade internal abort exit print

Downgrade the exit print in hisi_sas_internal_task_abort()
to dbg level, as info is not required.

Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: modify hard reset for directed-attached disk

Correctly set registers in v2 for root PHY hardreset for directly
attached disk.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: downgrade refclk message

The message to inform that the controller has no refclk
is currently at warning level, which is unnecessary, so
downgrade to debug.

Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: modify some values of ITCT table

Set SMP connection timeout and continue AWT timer;
Clear ITCT table when dev gone.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: workaround v2 hw SATA IO timeout issue

The v2 SAS controller needs more time to detect channel idle
and send setup link request than SATA disk does, so it is
difficult for the SAS controller to setup an STP link. Therefore
it may cause some IO timeouts.

We need to periodically configure the SAS controller so it
doesn't receive STP setup requests from SATA disks for a while,
so IO can be sent during this period.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Fix lpfc_wwn_set return code check

When I reversed the patch to re-add the lpfc_soft_wwn parameter feature,
it re-added code that had a long-standing bug. (that's what I get I
guess :)

As Dan Carpenter pointed out - error checks looked at wrong polarity.  0
is success, -errno is failure. Updated checks.

Signed-off-by: James Smart <james.smart@broadcom.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: sd: Cleaned up comment references to @sdp argument explanation.

In sd.c there are two comment references to 'struct scsi_device *sdp' as
an argument.  One of the references has a typo and the other should be a
reference to 'struct device *dev' instead.

Fixed by correcting the typo in the first and changing the explanation
in the second.

Signed-off-by: John Pittman <jpittman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: be2iscsi: Use GFP_ATOMIC under spin lock

A spin lock is taken here so we should use GFP_ATOMIC.

Fixes: 987132167f4b ("scsi: be2iscsi: Fix for crash in beiscsi_eh_device_reset")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Replace BUG() with BUG_ON()

Replace BUG() with BUG_ON() using coccinelle.

Signed-off-by: Shyam Saini <mayhs11saini@gmail.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: remove two unused MSI-X related #defines

Spotted while preparing qla2xxx changes as the symbols exist in both
drivers (sigh..).

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: cxlflash: Cancel scheduled workers before stopping AFU

When processing an AFU asynchronous interrupt, if the action results in an
operation that requires off level processing (a link reset for example),
the worker thread is scheduled. In the meantime a reset event (i.e.: EEH)
could unmap the AFU to recover. This results in an Oops when the worker
thread tries to access the AFU mapping.

[c000000f17e03b90] d000000007cd5978 cxlflash_worker_thread+0x268/0x550
[c000000f17e03c40] c00000000011883c process_one_work+0x1dc/0x680
[c000000f17e03ce0] c000000000118e80 worker_thread+0x1a0/0x520
[c000000f17e03d80] c000000000126174 kthread+0xf4/0x100
[c000000f17e03e30] c00000000000a47c ret_from_kernel_thread+0x5c/0xe0

In an effort to avoid this, a mapcount was introduced in
commit b45cdbaf9f7f ("cxlflash: Resolve oops in wait_port_offline")
but due to the race condition described above, this solution is incomplete.

In order to fully resolve this problem and to simplify things, this commit
removes the mapcount solution. Instead, the scheduled worker thread is
cancelled after interrupts have been disabled and prior to the mapping
being freed.

Fixes: b45cdbaf9f7f ("cxlflash: Resolve oops in wait_port_offline")
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: cxlflash: Cleanup prints

The usage of prints within the cxlflash driver is inconsistent. This
hinders debug and makes the driver source and log output appear sloppy.

The following cleanups help unify the prints within cxlflash:
 - move all prints to dev-* where possible
 - transition all hex prints to lowercase
 - standardize variable prints in debug output
 - derive pointers in a consistent manner
 - change int to bool where appropriate
 - remove superfluous data from prints and print statements that do not
   make sense

Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: cxlflash: Support SQ Command Mode

The SISLite specification outlines a new queuing model to improve
over the MMIO-based IOARRIN model that exists today. This new model
uses a submission queue that exists in host memory and is shared with
the device. Each entry in the queue is an IOARCB that describes a
transfer request. When requests are submitted, IOARCBs ('current'
position tracked in host software) are populated and the submission
queue tail pointer is then updated via MMIO to make the device aware
of the requests.

Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: cxlflash: Refactor context reset to share reset logic

As staging for supporting hardware with different context reset
registers but a similar reset procedure, refactor the existing context
reset routine to move the reset logic to a common routine. This will
allow hardware with a different reset register to leverage existing
code.

Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: fix arguments order some trace calls

Colin Ian King reported that with commit 7ff5ab473633 ("scsi: ufs: add
tracing support") static analysis is reporting that we may have swapped
arguments on calls to:

    trace_ufshcd_runtime_resume,
    trace_ufshcd_runtime_suspend,
    trace_ufshcd_system_suspend,
    trace_ufshcd_system_resume,
and trace_ufshcd_init

Where:
    hba->uic_link_state is passed to dev_state
    hba->curr_dev_pwr_mode is passed to link_state

This wasn't intentional so it's a bug. This change fixed this bug.

Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: vmw_pvscsi: switch to pci_alloc_irq_vectors

And simplify the interrupt handler by splitting the INTx case that needs
to deal with shared interrupts into a separate helper.

[mkp: typo fixage]

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jim Gill <jgill@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: driver version upgrade

Upgrade driver version.

Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: Implement the PD Map support for SAS3.5 Generic Megaraid Controllers

Update Linux driver to use new pdTargetId field for JBOD target ID

Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: ldio_outstanding variable is not decremented in completion path

ldio outstanding variable needs to be decremented in io completion path for
iMR dual queue depth

Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: Enable or Disable Fast path based on the PCI Threshold Bandwidth

Large SEQ IO workload should sent as non fast path commands

Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: Add the Support for SAS3.5 Generic Megaraid Controllers Capabilities

The Megaraid driver has to support the SAS3.5 Generic Megaraid Controllers Firmware functionality.

Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: Dynamic Raid Map Changes for SAS3.5 Generic Megaraid Controllers

SAS3.5 Generic Megaraid Controllers FW will support new dynamic RaidMap to have different
sizes for different number of supported VDs.

Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: SAS3.5 Generic Megaraid Controllers Fast Path for RAID 1/10 Writes

To improve RAID 1/10 Write performance, OS drivers need to issue the
required Write IOs as Fast Path IOs (after the appropriate checks
allowing Fast Path to be used) to the appropriate physical drives
(translated from the OS logical IO) and wait for all Write IOs to complete.

Design: A write IO on RAID volume will be examined if it can be sent in
Fast Path based on IO size and starting LBA and ending LBA falling on to
a Physical Drive boundary. If the underlying RAID volume is a RAID 1/10,
driver issues two fast path write IOs one for each corresponding physical
drive after computing the corresponding start LBA for each physical drive.
Both write IOs will have the same payload and are posted to HW such that
replies land in the same reply queue.

If there are no resources available for sending two IOs, driver will send
the original IO from SCSI layer to RAID volume through the Firmware.

Based on PCI bandwidth and write payload, every second this feature is
enabled/disabled.

When both IOs are completed by HW, the resources will be released
and SCSI IO completion handler will be called.

Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: SAS3.5 Generic Megaraid Controllers Stream Detection and IO Coalescing

Detect sequential Write IOs and pass the hint that it is part of sequential
stream to help HBA Firmware do the Full Stripe Writes. For read IOs on
certain RAID volumes like Read Ahead volumes,this will help driver to
send it to Firmware even if the IOs can potentially be sent to
hardware directly (called fast path) bypassing firmware.

Design: 8 streams are maintained per RAID volume as per the combined
firmware/driver design. When there is no stream detected the LRU stream
is used for next potential stream and LRU/MRU map is updated to make this
as MRU stream. Every time a stream is detected the MRU map
is updated to make the current stream as MRU stream.

Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: EEDP Escape Mode Support for SAS3.5 Generic Megaraid Controllers

An UNMAP command on a PI formatted device will leave the Logical Block Application
Tag and Logical Block Reference Tag as all F's (for those LBAs that are unmapped).
To avoid IO errors if those LBAs are subsequently read before they are written with
valid tag fields, the MPI SCSI IO requests need to set the EEDPFlags element EEDP
Escape Mode field, Bits [7:6] appropriately.  A value of 2 should be set to disable
all PI checks if the Logical Block Application Tag is 0xFFFF for PI types 1 and 2.
A value of 3 should be set to disable all PI checks if the Logical Block Application
Tag is 0xFFFF and the Logical Block Reference Tag is 0xFFFFFFFF for PI type 3.

Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: 128 MSIX Support

SAS3.5 Generic Megaraid based Controllers will have the support for 128 MSI-X vectors,
resulting in the need to support 128 reply queues

Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: Add new pci device Ids for SAS3.5 Generic Megaraid Controllers

This patch contains new pci device ids for SAS3.5 Generic Megaraid Controllers

Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: remove useless acpi functions in the header file

commit f1bc1e4c44b1 ("ata: acpi: rework the ata acpi bind support")
removed scsi_register_acpi_bus_type() and
scsi_unregister_acpi_bus_type(), but forgot to remove them in the header
file, do it now.

Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: refactor device descriptor reading

Pull device descriptor reading out of ufs quirk so it can be used also
for other purposes.

Revamp the fixup setup:

1. Rename ufs_device_info to ufs_dev_desc as very similar name
   ufs_dev_info is already in use.

2. Make the handlers static as they are not used out of the ufshdc.c
   file.

[mkp: applied by hand]

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: ufshcd_get_max_icc_level fix endianity handling

Reading big endian value from a buffer requires explicit cast.
Fix sparse warning:
drivers/scsi/ufs/ufshcd.c:4825:24: warning: cast to restricted __be16

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: unexport descritpor reading functions

Unexport ufshcd_read_device_desc and ufshcd_read_string_desc there is no
really possibility to calling them directly outside of UFS context.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: ufshcd_query_descriptor_retry should be static

Fix the following compilation warning:

drivers/scsi/ufs/ufshcd.c:2076:5: warning: no previous prototype for
 ufshcd_query_descriptor_retry  [-Wmissing-prototypes]

Also do not export the function, it should not be used out of ufs
context.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: esas2r: Fix format string type mistakes

This adds the missing __printf attribute which allows compile time
format string checking (and will be used by the coming initify gcc
plugin). Additionally, this fixes the warnings exposed by the attribute.

Signed-off-by: Emese Revfy <re.emese@gmail.com>
[kees: split scsi/acpi, merged attr and fix, new commit messages]
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pmcraid: switch to pci_alloc_irq_vectors

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bfa: remove bfa_fcs_mod_s

Just call the functions directly instead of obsfucating the call chain.
This was in reply to a patch from Kees Cook to constify the function
pointer struct bfa_fcs_mod_s, but it turns out there is no reason to
have this indirection at all.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: rename {vendor|hba}_indentifer to {vendor|hba}_identifer

Rename the vendor_indentifer and hba_indentifer fields to correct
spelling.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: make msix_entries const

msix_entries and qla82xx_msix_entries arrays are never modified in
drivers/scsi/qla2xxx/qla_isr.c. Move their contents to read-only data.

Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: silence -Wformat-security warning

qla24xx_enable_msix() calls scnprintf() with a non-literal format
string. This makes clang report -Wformat-security warnings when
compiling this function:

    drivers/scsi/qla2xxx/qla_isr.c:3083:7: error: format string is not a
    string literal (potentially insecure) [-Werror,-Wformat-security]
                        msix_entries[i].name);
                        ^~~~~~~~~~~~~~~~~~~~
    drivers/scsi/qla2xxx/qla_isr.c:3083:7: note: treat the string as an
    argument to avoid this
                        msix_entries[i].name);
                        ^
                        "%s",
    drivers/scsi/qla2xxx/qla_isr.c:3119:7: error: format string is not a
    string literal (potentially insecure) [-Werror,-Wformat-security]
                        msix_entries[QLA_ATIO_VECTOR].name);
                        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    drivers/scsi/qla2xxx/qla_isr.c:3119:7: note: treat the string as an
    argument to avoid this
                        msix_entries[QLA_ATIO_VECTOR].name);
                        ^
                        "%s",

Even though msix_entries[...].name are initialized as literal strings
with no % character and are never modified, introduce a "%s" format
parameter in order to silence this -Wformat-security warning and make
clang able to detect at compile time real bugs related to string
formatting.

[mkp: typo]

Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Reinstate lpfc_soft_wwn parameter

The lpfc 11.2.0.4 patch set deprecated, by removing, the lpfc_soft_wwn
parameter support.

This patch reinstates support, but adds a warning in the enablement of
the feature that indicates Broadcom (Emulex) does not support the
feature.

Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: lock sensitive region in hisi_sas_slot_abort()

When we call hisi_sas_slot_task_free() we should grab the hisi_hba.lock,
as hisi_sas_slot_task_free() accesses common hisi_hba elements.
Function hisi_sas_slot_abort() is missing this, so add it.

Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: lock sensitive regions when servicing CQ interrupt

There is a bug in the current driver in that certain hisi_hba and port
structure elements which we access when servicing the CQ interrupt do
not use thread-safe accesses; these include hisi_sas_port linked-list of
active slots (hisi_sas_port.entry), bitmap of currently allocated IPTT
(in hisi_hba.slot_index_tags), and completion queue read pointer.

As a solution, lock these elements with the hisi_hba.lock.

Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: service v2 hw CQ ISR with tasklet

Currently the all the slot processing for the completion queue is done
in ISR context. It is judged that the slot processing can take a long
time, especially when a SATA NCQ completes (upto 32 slots).

So, as a solution, defer the bulk of the ISR processing to tasklet
context. Each CQ will have its down tasklet.

Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs-qcom: Fix module autoload

If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/scsi/ufs/ufs-qcom.ko | grep alias
$

After this patch:

$ modinfo drivers/scsi/ufs/ufs-qcom.ko | grep alias
alias:          of:N*T*Cqcom,ufshcC*
alias:          of:N*T*Cqcom,ufshc

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Improve fatal error logs

Errors such as UIC error, illegal OCS values, and others may require
more information for debugging. Such information could be hibern8 events,
events sequences, recoverable errors, error history, and more.
This patch improves tracking of important errors and events in debug level
to be enabled when debugging a such issues. It includes:
* UIC error history
* Successful hibern8 events
* Successful command after hibern8 exit
* Clk-freq info
* Failed device command
* Infrastructure for dumping host controller debug information

Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: add trace event for ufs commands

Use the ftrace infrastructure to conditionally trace ufs command events.
New trace event is created, which samples the following ufs command data:
- device name
- optional identification string
- task tag
- doorbell register
- number of transfer bytes
- interrupt status register
- request start LBA
- command opcode

Currently we only fully trace read(10) and write(10) commands.
All other commands which pass through ufshcd_send_command() will be
printed with "-1" in the lba and transfer_len fields.

Usage:
echo 1 > /sys/kernel/debug/tracing/events/ufs/enable
cat /sys/kernel/debug/tracing/trace_pipe

Signed-off-by: Lee Susman <lsusman@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: add time profiling support

This patch adds the profiling support for some of the time critical
operations like hibern8 enter/exit, clock gating & clock scaling.

Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: fix setting init power mode

Immediately after successful UFS link startup, UFS link power mode would
be in PWM-G1, 1-lane, SLOW-AUTO mode. But currently we are doing few
of the DME local/peer attributes access before setting the "hba->pwr_info"
to default power mode. If we are doing link startup as part of error
recovery then old power mode might be set to FAST mode and doing DME peer
access (after link startup but before updating "hba->pwr_info" to default
power mode) unintentionally tries to switch from FAST to FAST_AUTO mode (if
UFSHCD_QUIRK_DME_PEER_ACCESS_AUTO_MODE quirk is enabled).

Above issue is fixed by setting the default power mode immediately after
successful link startup.

Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: add capability to keep auto bkops always enabled

UFS device requires to perform bkops (back ground operations) periodically
but host can control (via auto-bkops parameter of device) when device can
perform bkops based on its performance requirements. In general, host
would like to enable the device's auto-bkops only when it's not doing any
regular data transfer but sometimes device may not behave properly if host
keeps the auto-bkops disabled. This change adds the capability to let the
device auto-bkops always enabled except suspend.

Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: set default UFS power management level

UFS device and link can be put in multiple different low power modes hence
UFS driver supports multiple different low power modes.
This change sets the default UFS power management level which should put
the link hibernate state and device in sleep state. This default power
management level gives good  power savings with relatively less enter/exit
latencies.

Reviewed-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: provide sysfs attribute to select the PM level

This patch provides the sysfs attribute to choose the power management
level for UFS runtime and system suspend.

Reviewed-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Add sysfs node to dynamically control clock scaling

Provide an option to enable/disable clock scaling during runtime.
Write 1/0 to "clkscale_enable" sysfs node to enable/disable clock
scaling.

Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Add sysfs node to dynamically control clock gating

Provide an option to enable/disable clock gating during runtime.
Write 1 or 0 to "clkgate_enable" sysfs node to enable/disable
clock gating.

Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: fix multiple ufs spec violation

When a command to a W-LU is timed out via scsi, error handling
will treat it as any other LU and send commands such as
START_STOP with wrong format or task abort. Those commands are
illegal for W-LU according to the UFS spec.
To solve it, when an error is recognized those steps are skipped
and the last step, reset and restore process, is initiated.

Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: add tracing support

This change adds the ftrace support for following:
1. UFS initialization time
2. Clock gating states
3. Clock scaling states
4. Power management APIs latency
5. BKOPs enable/disable

Usage:
echo 1 > /sys/kernel/debug/tracing/events/ufs/enable
cat /sys/kernel/debug/tracing/trace_pipe

Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: dump debug info during failures

Inserts driver dumps for UFS Host Controller registers, Transfer Requests
and Task Management Requests.
The dumps will occur on driver initialization failure, ufshcd_abort() and
on error handling path.

Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: comments correction

Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Acked-by: Nilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedi: return via va_end to match corresponding va_start

Although on most systems va_end is a no-op, it is good practice to use
va_end on the function return path, especially since the va_start
documenation states:

  "Each invocation of va_start() must be matched by a corresponding
   invocation of va_end() in the same function."

Found with static analysis by CoverityScan, CIDs 1389477-1389479

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: be2iscsi: Update driver version

Version 11.2.1.0

Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: be2iscsi: Add warning message for unsupported adapter

Add a warning message to indicate obsolete/unsupported
BE2 Adapter Family devices

Signed-off-by: Ketan Mukadam <ketan.mukadam@avagotech.com>
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: be2iscsi: Reinit SGL handle, CID tables after TPE

After TPE recovery, CID table needs to be repopulated as per CIDs in
WRBQ creation responses.

SGL handles table needs to be recreated for posting and its indices need
to be resetted.

This is achieved by calling beiscsi_cleanup_port when disabling and
beiscsi_init_port in enabling port.

Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: be2iscsi: Add checks to validate CID alloc/free

Set CID slot to 0xffff to indicate empty.
Check if connection already exists in conn_table before binding.
Check if endpoint already NULL before putting back CID.
Break ep->conn link in free_ep to ignore completions after freeing.

Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: be2iscsi: Remove wq_name from beiscsi_hba

wq_name is used only to set WQ name when its being allocated.
Remove it from beiscsi_hba structure and define locally.

Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: be2iscsi: Remove unused struct members

Fix errors reported in static analysis.

Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: be2iscsi: Remove redundant receive buffers posting

This duplicate code got added during manual merging.

Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: be2iscsi: Fix iSCSI cmd cleanup IOCTL

Prepare the IOCTL with appropriate sizes of buffers of V0 and V1.
Set missing chute number in V1 IOCTL.

Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: be2iscsi: Add checks to validate completions

Added check in beiscsi_process_cq for pio_handle.
pio_handle is cleared in beiscsi_put_wrb_handle.
This catches any case where task gets cleaned up just before completion.

Use back_lock before accessing pio_handle.

Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: be2iscsi: Set WRB invalid bit for SkyHawk

invalid bit in WRB indicates to FW that IO was invalidated before WRB
was fetched from host memory.

For SkyHawk, this invalid bit in WRB is at a different offset.
Use amap_iscsi_wrb_v2 to mark invalid bit for SkyHawk.

Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: be2iscsi: Take iscsi_task ref in abort handler

Hold the reference of iscsi_task till invalidation completes.
This prevents use of ICD when invalidation of that ICD is being processed.

Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: be2iscsi: Fix for crash in beiscsi_eh_device_reset

System crashes when sg_reset is executed in a loop.
CPU: 13 PID: 7073 Comm: sg_reset Tainted: G            E   4.8.0-rc1+ #4
RIP: 0010:[<ffffffffa0825370>]  [<ffffffffa0825370>]
beiscsi_eh_device_reset+0x160/0x520 [be2iscsi]
Call Trace:
[<ffffffff814c7c77>] ? scsi_host_alloc_command+0x47/0xc0
[<ffffffff814caafa>] scsi_try_bus_device_reset+0x2a/0x50
[<ffffffff814cb46e>] scsi_ioctl_reset+0x13e/0x260
[<ffffffff814ca477>] scsi_ioctl+0x137/0x3d0
[<ffffffffa05e4ba2>] sg_ioctl+0x572/0xc20 [sg]
[<ffffffff8123f627>] do_vfs_ioctl+0xa7/0x5d0

The accesses to beiscsi_io_task is being protected in device reset handler
with frwd_lock but the freeing of task can happen under back_lock.

Hold the reference of iscsi_task till invalidation completes.
This prevents use of ICD when invalidation of that ICD is being processed.
Use frwd_lock for iscsi_tasks looping and back_lock to access
beiscsi_io_task structures.

Rewrite mgmt_invalidation_icds to handle allocation and freeing of IOCTL
buffer in one place.

Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: be2iscsi: Fix use of invalidate command table req

Remove shared structure inv_tbl in phba for all sessions to post
invalidation IOCTL.
Always allocate and then free the table after use in reset handler.
Abort handler needs just one instance so define it on stack.
Add checks for BE_INVLDT_CMD_TBL_SZ to not exceed invalidation
command table size in IOCTL.

Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>