OSDN Git Service
Lars Persson [Fri, 1 Dec 2017 10:12:44 +0000 (11:12 +0100)]
stmmac: reset last TSO segment size after device open
The mss variable tracks the last max segment size sent to the TSO
engine. We do not update the hardware as long as we receive skb:s with
the same value in gso_size.
During a network device down/up cycle (mapped to stmmac_release() and
stmmac_open() callbacks) we issue a reset to the hardware and it
forgets the setting for mss. However we did not zero out our mss
variable so the next transmission of a gso packet happens with an
undefined hardware setting.
This triggers a hang in the TSO engine and eventuelly the netdev
watchdog will bark.
Fixes:
f748be531d70 ("stmmac: support new GMAC4")
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gao Feng [Fri, 1 Dec 2017 01:58:42 +0000 (09:58 +0800)]
ipvlan: Add the skb->mark as flow4's member to lookup route
Current codes don't use skb->mark to assign flowi4_mark, it would
make the policy route rule with fwmark doesn't work as expected.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 3 Dec 2017 02:35:21 +0000 (21:35 -0500)]
Merge branch 's390-qeth-fixes'
Julian Wiedmann says:
====================
s390/qeth: fixes 2017-12-01
please apply the following three fixes for 4.15. These should also go
back to stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 1 Dec 2017 09:14:51 +0000 (10:14 +0100)]
s390/qeth: build max size GSO skbs on L2 devices
The current GSO skb size limit was copy&pasted over from the L3 path,
where it is needed due to a TSO limitation.
As L2 devices don't offer TSO support (and thus all GSO skbs are
segmented before they reach the driver), there's no reason to restrict
the stack in how large it may build the GSO skbs.
Fixes:
d52aec97e5bc ("qeth: enable scatter/gather in layer 2 mode")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 1 Dec 2017 09:14:50 +0000 (10:14 +0100)]
s390/qeth: fix GSO throughput regression
Using GSO with small MTUs currently results in a substantial throughput
regression - which is caused by how qeth needs to map non-linear skbs
into its IO buffer elements:
compared to a linear skb, each GSO-segmented skb effectively consumes
twice as many buffer elements (ie two instead of one) due to the
additional header-only part. This causes the Output Queue to be
congested with low-utilized IO buffers.
Fix this as follows:
If the MSS is low enough so that a non-SG GSO segmentation produces
order-0 skbs (currently ~3500 byte), opt out from NETIF_F_SG. This is
where we anticipate the biggest savings, since an SG-enabled
GSO segmentation produces skbs that always consume at least two
buffer elements.
Larger MSS values continue to get a SG-enabled GSO segmentation, since
1) the relative overhead of the additional header-only buffer element
becomes less noticeable, and
2) the linearization overhead increases.
With the throughput regression fixed, re-enable NETIF_F_SG by default to
reap the significant CPU savings of GSO.
Fixes:
5722963a8e83 ("qeth: do not turn on SG per default")
Reported-by: Nils Hoppmann <niho@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 1 Dec 2017 09:14:49 +0000 (10:14 +0100)]
s390/qeth: fix thinko in IPv4 multicast address tracking
Commit
5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
reworked how secondary addresses are managed for qeth devices.
Instead of dropping & subsequently re-adding all addresses on every
ndo_set_rx_mode() call, qeth now keeps track of the addresses that are
currently registered with the HW.
On a ndo_set_rx_mode(), we thus only need to do (de-)registration
requests for the addresses that have actually changed.
On L3 devices, the lookup for IPv4 Multicast addresses checks the wrong
hashtable - and thus never finds a match. As a result, we first delete
*all* such addresses, and then re-add them again. So each set_rx_mode()
causes a short period where the IPv4 Multicast addresses are not
registered, and the card stops forwarding inbound traffic for them.
Fix this by setting the ->is_multicast flag on the lookup object, thus
enabling qeth_l3_ip_from_hash() to search the correct hashtable and
find a match there.
Fixes:
5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 3 Dec 2017 02:31:04 +0000 (21:31 -0500)]
Merge branch 'vhost-skb-leaks'
Wei Xu says:
====================
vhost: fix a few skb leaks
Matthew found a roughly 40% tcp throughput regression with commit
c67df11f(vhost_net: try batch dequing from skb array) as discussed
in the following thread:
https://www.mail-archive.com/netdev@vger.kernel.org/msg187936.html
v4:
- fix zero iov iterator count in tap/tap_do_read()(Jason)
- don't put tun in case of EBADFD(Jason)
- Replace msg->msg_control with new 'skb' when calling tun/tap_do_read()
v3:
- move freeing skb from vhost to tun/tap recvmsg() to not
confuse the callers.
v2:
- add Matthew as the reporter, thanks matthew.
- moving zero headcount check ahead instead of defer consuming skb
due to jason and mst's comment.
- add freeing skb in favor of recvmsg() fails.
====================
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Xu [Fri, 1 Dec 2017 10:10:38 +0000 (05:10 -0500)]
tap: free skb if flags error
tap_recvmsg() supports accepting skb by msg_control after
commit
3b4ba04acca8 ("tap: support receiving skb from msg_control"),
the skb if presented should be freed within the function, otherwise
it would be leaked.
Signed-off-by: Wei Xu <wexu@redhat.com>
Reported-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Xu [Fri, 1 Dec 2017 10:10:37 +0000 (05:10 -0500)]
tun: free skb in early errors
tun_recvmsg() supports accepting skb by msg_control after
commit
ac77cfd4258f ("tun: support receiving skb through msg_control"),
the skb if presented should be freed no matter how far it can go
along, otherwise it would be leaked.
This patch fixes several missed cases.
Signed-off-by: Wei Xu <wexu@redhat.com>
Reported-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Xu [Fri, 1 Dec 2017 10:10:36 +0000 (05:10 -0500)]
vhost: fix skb leak in handle_rx()
Matthew found a roughly 40% tcp throughput regression with commit
c67df11f(vhost_net: try batch dequing from skb array) as discussed
in the following thread:
https://www.mail-archive.com/netdev@vger.kernel.org/msg187936.html
Eventually we figured out that it was a skb leak in handle_rx()
when sending packets to the VM. This usually happens when a guest
can not drain out vq as fast as vhost fills in, afterwards it sets
off the traffic jam and leaks skb(s) which occurs as no headcount
to send on the vq from vhost side.
This can be avoided by making sure we have got enough headcount
before actually consuming a skb from the batched rx array while
transmitting, which is simply done by moving checking the zero
headcount a bit ahead.
Signed-off-by: Wei Xu <wexu@redhat.com>
Reported-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 3 Dec 2017 02:25:39 +0000 (21:25 -0500)]
Merge branch 'bnxt_en-fixes'
Michael Chan says:
====================
bnxt_en: Fixes.
A shutdown fix for SMARTNIC, 2 fixes related to TC Flower vxlan
filters, and the last one fixes an out-of-scope variable when sending
short firmware messages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Fri, 1 Dec 2017 08:13:05 +0000 (03:13 -0500)]
bnxt_en: Fix a variable scoping in bnxt_hwrm_do_send_msg()
short_input variable is assigned to another data pointer which is
referred out of its scope. Fix it by moving short_input definition
to the beginning of bnxt_hwrm_do_send_msg() function.
No failure has been reported so far due to this issue.
Fixes:
e605db801bde ("bnxt_en: Support for Short Firmware Message")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Fri, 1 Dec 2017 08:13:04 +0000 (03:13 -0500)]
bnxt_en: fix dst/src fid for vxlan encap/decap actions
For flows that involve a vxlan encap action, the vxlan sock
interface may be specified as the outgoing interface. The driver
must resolve the outgoing PF interface used by this socket and
use the dst_fid of the PF in the hwrm_cfa_encap_record_alloc cmd.
Similarily for flows that have a vxlan decap action, the
fid of the incoming PF interface must be used as the src_fid in
the hwrm_cfa_decap_filter_alloc cmd.
Fixes:
8c95f773b4a3 ("bnxt_en: add support for Flower based vxlan encap/decap offload")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Challa [Fri, 1 Dec 2017 08:13:03 +0000 (03:13 -0500)]
bnxt_en: wildcard smac while creating tunnel decap filter
While creating a decap filter the tunnel smac need not (and must not) be
specified as we cannot ascertain the neighbor in the recv path. 'ttl'
match is also not needed for the decap filter and must be wild-carded.
Fixes:
f484f6782e01 ("bnxt_en: add hwrm FW cmds for cfa_encap_record and decap_filter")
Signed-off-by: Sunil Challa <sunilkumar.challa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ray Jui [Fri, 1 Dec 2017 08:13:02 +0000 (03:13 -0500)]
bnxt_en: Need to unconditionally shut down RoCE in bnxt_shutdown
The current 'bnxt_shutdown' implementation only invokes
'bnxt_ulp_shutdown' to shut down RoCE in the case when the system is in
the path of power off (SYSTEM_POWER_OFF). While this may work in most
cases, it does not work in the smart NIC case, when Linux 'reboot'
command is initiated from the Linux that runs on the ARM cores of the
NIC card. In this particular case, Linux 'reboot' results in a system
'L3' level reset where the entire ARM and associated subsystems are
being reset, but at the same time, Nitro core is being kept in sane state
(to allow external PCIe connected servers to continue to work). Without
properly shutting down RoCE and freeing all associated resources, it
results in the ARM core to hang immediately after the 'reboot'
By always invoking 'bnxt_ulp_shutdown' in 'bnxt_shutdown', it fixes the
above issue
Fixes:
0efd2fc65c92 ("bnxt_en: Add a callback to inform RDMA driver during PCI shutdown.")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 1 Dec 2017 20:18:42 +0000 (15:18 -0500)]
Merge branch 'sfp-phylink-fixes'
Russell King says:
====================
SFP/phylink fixes
Here are four phylink fixes:
- the "options" is a big-endian value, we must test the bits taking the
endian-ness into account.
- improve the handling of RX_LOS polarity, taking no RX_LOS polarity
bits set to mean there is no RX_LOS functionality provided.
- do not report modules that require the address mode switching as
supporting SFF8472.
- ensure that the mac_link_down() function is called when phylink_stop()
is called.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 30 Nov 2017 13:59:26 +0000 (13:59 +0000)]
phylink: ensure we take the link down when phylink_stop() is called
Ensure that we tell the MAC to take the link down when phylink_stop()
is called, and that this completes prior to phylink_stop() returns.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 30 Nov 2017 13:59:21 +0000 (13:59 +0000)]
sfp: warn about modules requiring address change sequence
We do not support SFP modules which require the address change sequence
as detailed by SFF 8472 revision 1.22 section 8.9. Warn when these
modules are inserted, and treat them as SFF8079 modules for ethtool.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 30 Nov 2017 13:59:16 +0000 (13:59 +0000)]
sfp: improve RX_LOS handling
There are two bits in the option word for the RX_LOS signal. One
reports that the RX_LOS signal is active high, the other reports that
it is active low. When both or neither are set, the result is not
well defined in the specification.
Rather than assuming that neither set means normal RX_LOS, take this
as meaning no RX_LOS signal available, thereby ignoring the signal.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 30 Nov 2017 13:59:11 +0000 (13:59 +0000)]
sfp: fix RX_LOS signal handling
The options word is a be16 quantity, so we need to test the flags
having converted the endian-ness. Convert the flag bits to be16,
which can be optimised by the compiler, rather than converting a
variable at runtime.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Max Uvarov [Thu, 30 Nov 2017 10:08:29 +0000 (13:08 +0300)]
net: phy-micrel: check return code in flp center function
Fix obvious typo that first return value is set but not checked.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tommi Rantala [Wed, 29 Nov 2017 10:48:42 +0000 (12:48 +0200)]
tipc: call tipc_rcv() only if bearer is up in tipc_udp_recv()
Remove the second tipc_rcv() call in tipc_udp_recv(). We have just
checked that the bearer is not up, and calling tipc_rcv() with a bearer
that is not up leads to a TIPC div-by-zero crash in
tipc_node_calculate_timer(). The crash is rare in practice, but can
happen like this:
We're enabling a bearer, but it's not yet up and fully initialized.
At the same time we receive a discovery packet, and in tipc_udp_recv()
we end up calling tipc_rcv() with the not-yet-initialized bearer,
causing later the div-by-zero crash in tipc_node_calculate_timer().
Jon Maloy explains the impact of removing the second tipc_rcv() call:
"link setup in the worst case will be delayed until the next arriving
discovery messages, 1 sec later, and this is an acceptable delay."
As the tipc_rcv() call is removed, just leave the function via the
rcu_out label, so that we will kfree_skb().
[ 12.590450] Own node address <1.1.1>, network identity 1
[ 12.668088] divide error: 0000 [#1] SMP
[ 12.676952] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.14.2-dirty #1
[ 12.679225] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-2.fc27 04/01/2014
[ 12.682095] task:
ffff8c2a761edb80 task.stack:
ffffa41cc0cac000
[ 12.684087] RIP: 0010:tipc_node_calculate_timer.isra.12+0x45/0x60 [tipc]
[ 12.686486] RSP: 0018:
ffff8c2a7fc838a0 EFLAGS:
00010246
[ 12.688451] RAX:
0000000000000000 RBX:
ffff8c2a5b382600 RCX:
0000000000000000
[ 12.691197] RDX:
0000000000000000 RSI:
ffff8c2a5b382600 RDI:
ffff8c2a5b382600
[ 12.693945] RBP:
ffff8c2a7fc838b0 R08:
0000000000000001 R09:
0000000000000001
[ 12.696632] R10:
0000000000000000 R11:
0000000000000000 R12:
ffff8c2a5d8949d8
[ 12.699491] R13:
ffffffff95ede400 R14:
0000000000000000 R15:
ffff8c2a5d894800
[ 12.702338] FS:
0000000000000000(0000) GS:
ffff8c2a7fc80000(0000) knlGS:
0000000000000000
[ 12.705099] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 12.706776] CR2:
0000000001bb9440 CR3:
00000000bd009001 CR4:
00000000003606e0
[ 12.708847] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[ 12.711016] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[ 12.712627] Call Trace:
[ 12.713390] <IRQ>
[ 12.714011] tipc_node_check_dest+0x2e8/0x350 [tipc]
[ 12.715286] tipc_disc_rcv+0x14d/0x1d0 [tipc]
[ 12.716370] tipc_rcv+0x8b0/0xd40 [tipc]
[ 12.717396] ? minmax_running_min+0x2f/0x60
[ 12.718248] ? dst_alloc+0x4c/0xa0
[ 12.718964] ? tcp_ack+0xaf1/0x10b0
[ 12.719658] ? tipc_udp_is_known_peer+0xa0/0xa0 [tipc]
[ 12.720634] tipc_udp_recv+0x71/0x1d0 [tipc]
[ 12.721459] ? dst_alloc+0x4c/0xa0
[ 12.722130] udp_queue_rcv_skb+0x264/0x490
[ 12.722924] __udp4_lib_rcv+0x21e/0x990
[ 12.723670] ? ip_route_input_rcu+0x2dd/0xbf0
[ 12.724442] ? tcp_v4_rcv+0x958/0xa40
[ 12.725039] udp_rcv+0x1a/0x20
[ 12.725587] ip_local_deliver_finish+0x97/0x1d0
[ 12.726323] ip_local_deliver+0xaf/0xc0
[ 12.726959] ? ip_route_input_noref+0x19/0x20
[ 12.727689] ip_rcv_finish+0xdd/0x3b0
[ 12.728307] ip_rcv+0x2ac/0x360
[ 12.728839] __netif_receive_skb_core+0x6fb/0xa90
[ 12.729580] ? udp4_gro_receive+0x1a7/0x2c0
[ 12.730274] __netif_receive_skb+0x1d/0x60
[ 12.730953] ? __netif_receive_skb+0x1d/0x60
[ 12.731637] netif_receive_skb_internal+0x37/0xd0
[ 12.732371] napi_gro_receive+0xc7/0xf0
[ 12.732920] receive_buf+0x3c3/0xd40
[ 12.733441] virtnet_poll+0xb1/0x250
[ 12.733944] net_rx_action+0x23e/0x370
[ 12.734476] __do_softirq+0xc5/0x2f8
[ 12.734922] irq_exit+0xfa/0x100
[ 12.735315] do_IRQ+0x4f/0xd0
[ 12.735680] common_interrupt+0xa2/0xa2
[ 12.736126] </IRQ>
[ 12.736416] RIP: 0010:native_safe_halt+0x6/0x10
[ 12.736925] RSP: 0018:
ffffa41cc0cafe90 EFLAGS:
00000246 ORIG_RAX:
ffffffffffffff4d
[ 12.737756] RAX:
0000000000000000 RBX:
ffff8c2a761edb80 RCX:
0000000000000000
[ 12.738504] RDX:
0000000000000000 RSI:
0000000000000000 RDI:
0000000000000000
[ 12.739258] RBP:
ffffa41cc0cafe90 R08:
0000014b5b9795e5 R09:
ffffa41cc12c7e88
[ 12.740118] R10:
0000000000000000 R11:
0000000000000000 R12:
0000000000000002
[ 12.740964] R13:
ffff8c2a761edb80 R14:
0000000000000000 R15:
0000000000000000
[ 12.741831] default_idle+0x2a/0x100
[ 12.742323] arch_cpu_idle+0xf/0x20
[ 12.742796] default_idle_call+0x28/0x40
[ 12.743312] do_idle+0x179/0x1f0
[ 12.743761] cpu_startup_entry+0x1d/0x20
[ 12.744291] start_secondary+0x112/0x120
[ 12.744816] secondary_startup_64+0xa5/0xa5
[ 12.745367] Code: b9 f4 01 00 00 48 89 c2 48 c1 ea 02 48 3d d3 07 00
00 48 0f 47 d1 49 8b 0c 24 48 39 d1 76 07 49 89 14 24 48 89 d1 31 d2 48
89 df <48> f7 f1 89 c6 e8 81 6e ff ff 5b 41 5c 5d c3 66 90 66 2e 0f 1f
[ 12.747527] RIP: tipc_node_calculate_timer.isra.12+0x45/0x60 [tipc] RSP:
ffff8c2a7fc838a0
[ 12.748555] ---[ end trace
1399ab83390650fd ]---
[ 12.749296] Kernel panic - not syncing: Fatal exception in interrupt
[ 12.750123] Kernel Offset: 0x13200000 from 0xffffffff82000000
(relocation range: 0xffffffff80000000-0xffffffffbfffffff)
[ 12.751215] Rebooting in 60 seconds..
Fixes:
c9b64d492b1f ("tipc: add replicast peer discovery")
Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 1 Dec 2017 18:06:56 +0000 (10:06 -0800)]
tcp/dccp: block bh before arming time_wait timer
Maciej Żenczykowski reported some panics in tcp_twsk_destructor()
that might be caused by the following bug.
timewait timer is pinned to the cpu, because we want to transition
timwewait refcount from 0 to 4 in one go, once everything has been
initialized.
At the time commit
ed2e92394589 ("tcp/dccp: fix timewait races in timer
handling") was merged, TCP was always running from BH habdler.
After commit
5413d1babe8f ("net: do not block BH while processing
socket backlog") we definitely can run tcp_time_wait() from process
context.
We need to block BH in the critical section so that the pinned timer
has still its purpose.
This bug is more likely to happen under stress and when very small RTO
are used in datacenter flows.
Fixes:
5413d1babe8f ("net: do not block BH while processing socket backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 1 Dec 2017 20:06:31 +0000 (15:06 -0500)]
Merge branch 'sctp-prsctp-chunk-fixes'
Xin Long says:
====================
sctp: a couple of fixes for chunks abandoned in prsctp
Now when abandoning chunks in prsctp, it doesn't consider for frags in
one msg, which would cause peer can never receive the whole frags for
one msg to get them reassembled, these pieces of this msg will stay in
the reasm queue forever and block the following chunks' receiving.
This patchset is to fix them in patch 2 and 3, and also fix another
issue for prsctp in patch 1.
====================
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sat, 25 Nov 2017 13:18:36 +0000 (21:18 +0800)]
sctp: do not abandon the other frags in unsent outq if one msg has outstanding frags
Now for the abandoned chunks in unsent outq, it would just free the chunks.
Because no tsn is assigned to them yet, there's no need to send fwd tsn to
peer, unlike for the abandoned chunks in sent outq.
The problem is when parts of the msg have been sent and the other frags
are still in unsent outq, if they are abandoned/dropped, the peer would
never get this msg reassembled.
So these frags in unsent outq can't be dropped if this msg already has
outstanding frags.
This patch does the check in sctp_chunk_abandoned and
sctp_prsctp_prune_unsent.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sat, 25 Nov 2017 13:18:35 +0000 (21:18 +0800)]
sctp: abandon the whole msg if one part of a fragmented message is abandoned
As rfc3758#section-3.1 demands:
A3) When a TSN is "abandoned", if it is part of a fragmented message,
all other TSN's within that fragmented message MUST be abandoned
at the same time.
Besides, if it couldn't handle this, the rest frags would never get
assembled in peer side.
This patch supports it by adding abandoned flag in sctp_datamsg, when
one chunk is being abandoned, set chunk->msg->abandoned as well. Next
time when checking for abandoned, go checking chunk->msg->abandoned
first.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sat, 25 Nov 2017 13:18:34 +0000 (21:18 +0800)]
sctp: only update outstanding_bytes for transmitted queue when doing prsctp_prune
Now outstanding_bytes is only increased when appending chunks into one
packet and sending it at 1st time, while decreased when it is about to
move into retransmit queue. It means outstanding_bytes value is already
decreased for all chunks in retransmit queue.
However sctp_prsctp_prune_sent is a common function to check the chunks
in both transmitted and retransmit queue, it decrease outstanding_bytes
when moving a chunk into abandoned queue from either of them.
It could cause outstanding_bytes underflow, as it also decreases it's
value for the chunks in retransmit queue.
This patch fixes it by only updating outstanding_bytes for transmitted
queue when pruning queues for prsctp prio policy, the same fix is also
needed in sctp_check_transmitted.
Fixes:
8dbdf1f5b09c ("sctp: implement prsctp PRIO policy")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 30 Nov 2017 18:45:26 +0000 (10:45 -0800)]
net: dsa: bcm_sf2: Set correct CHAIN_ID and slice number mask
When configuring an IPv6 address mask, we should use SLICE_NUM_MASK as
the mask in order to make sure all bits are masked by the hardware.
Also, we want matching entries to have a CHAIN_ID value set to the same
value as the rule index we return to user-space for convenience, so fix
that too.
Fixes:
ba0696c22e7c ("net: dsa: bcm_sf2: Add support for IPv6 CFP rules")
Fixes:
dd8eff68343d ("net: dsa: bcm_sf2: Allow matching arbitrary IPv6 masks/lengths")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Thu, 30 Nov 2017 02:41:14 +0000 (10:41 +0800)]
sit: update frag_off info
After parsing the sit netlink change info, we forget to update frag_off in
ipip6_tunnel_update(). Fix it by assigning frag_off with new value.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 30 Nov 2017 01:43:57 +0000 (17:43 -0800)]
tcp: remove buggy call to tcp_v6_restore_cb()
tcp_v6_send_reset() expects to receive an skb with skb->cb[] layout as
used in TCP stack.
MD5 lookup uses tcp_v6_iif() and tcp_v6_sdif() and thus
TCP_SKB_CB(skb)->header.h6
This patch probably fixes RST packets sent on behalf of a timewait md5
ipv6 socket.
Before Florian patch, tcp_v6_restore_cb() was needed before jumping to
no_tcp_socket label.
Fixes:
271c3b9b7bda ("tcp: honour SO_BINDTODEVICE for TW_RST case too")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Thu, 30 Nov 2017 00:07:51 +0000 (16:07 -0800)]
act_sample: get rid of tcf_sample_cleanup_rcu()
Similar to commit
d7fb60b9cafb ("net_sched: get rid of tcfa_rcu"),
TC actions don't need to respect RCU grace period, because it
is either just detached from tc filter (standalone case) or
it is removed together with tc filter (bound case) in which case
RCU grace period is already respected at filter layer.
Fixes:
5c5670fae430 ("net/sched: Introduce sample tc action")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 30 Nov 2017 15:07:34 +0000 (10:07 -0500)]
Merge tag 'rxrpc-fixes-
20171129' of git://git./linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fixes
Here are three patches for AF_RXRPC. One removes some whitespace, one
fixes terminal ACK generation and the third makes a couple of places
actually use the timeout value just determined rather than ignoring it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Corentin Labbe [Tue, 28 Nov 2017 16:48:22 +0000 (17:48 +0100)]
net: stmmac: dwmac-sun8i: fix allwinner,leds-active-low handling
The driver expect "allwinner,leds-active-low" to be in PHY node, but
the binding doc expect it to be in MAC node.
Since all board DT use it also in MAC node, the driver need to search
allwinner,leds-active-low in MAC node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Thu, 30 Nov 2017 13:33:56 +0000 (14:33 +0100)]
skbuff: Grammar s/are can/can/, s/change/changes/
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yan Markman [Thu, 30 Nov 2017 09:49:46 +0000 (10:49 +0100)]
net: mvpp2: allocate zeroed tx descriptors
Reserved and unused fields in the Tx descriptors should be 0. The PPv2
driver doesn't clear them at run-time (for performance reasons) but
these descriptors aren't zeroed when allocated, which can lead to
unpredictable behaviors. This patch fixes this by using
dma_zalloc_coherent instead of dma_alloc_coherent.
Fixes:
3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 29 Nov 2017 22:49:26 +0000 (14:49 -0800)]
Merge tag 'nfsd-4.15-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd fixes from Bruce Fields:
"I screwed up my merge window pull request; I only sent half of what I
meant to.
There were no new features, just bugfixes of various importance and
some very minor cleanup, so I think it's all still appropriate for
-rc2.
Highlights:
- Fixes from Trond for some races in the NFSv4 state code.
- Fix from Naofumi Honda for a typo in the blocked lock notificiation
code
- Fixes from Vasily Averin for some problems starting and stopping
lockd especially in network namespaces"
* tag 'nfsd-4.15-1' of git://linux-nfs.org/~bfields/linux: (23 commits)
lockd: fix "list_add double add" caused by legacy signal interface
nlm_shutdown_hosts_net() cleanup
race of nfsd inetaddr notifiers vs nn->nfsd_serv change
race of lockd inetaddr notifiers vs nlmsvc_rqst change
SUNRPC: make cache_detail structures const
NFSD: make cache_detail structures const
sunrpc: make the function arg as const
nfsd: check for use of the closed special stateid
nfsd: fix panic in posix_unblock_lock called from nfs4_laundromat
lockd: lost rollback of set_grace_period() in lockd_down_net()
lockd: added cleanup checks in exit_net hook
grace: replace BUG_ON by WARN_ONCE in exit_net hook
nfsd: fix locking validator warning on nfs4_ol_stateid->st_mutex class
lockd: remove net pointer from messages
nfsd: remove net pointer from debug messages
nfsd: Fix races with check_stateid_generation()
nfsd: Ensure we check stateid validity in the seqid operation checks
nfsd: Fix race in lock stateid creation
nfsd4: move find_lock_stateid
nfsd: Ensure we don't recognise lock stateids after freeing them
...
Linus Torvalds [Wed, 29 Nov 2017 22:26:50 +0000 (14:26 -0800)]
Merge tag 'for-4.15-rc2-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"We've collected some fixes in since the pre-merge window freeze.
There's technically only one regression fix for 4.15, but the rest
seems important and candidates for stable.
- fix missing flush bio puts in error cases (is serious, but rarely
happens)
- fix reporting stat::st_blocks for buffered append writes
- fix space cache invalidation
- fix out of bound memory access when setting zlib level
- fix potential memory corruption when fsync fails in the middle
- fix crash in integrity checker
- incremetnal send fix, path mixup for certain unlink/rename
combination
- pass flags to writeback so compressed writes can be throttled
properly
- error handling fixes"
* tag 'for-4.15-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: incremental send, fix wrong unlink path after renaming file
btrfs: tree-checker: Fix false panic for sanity test
Btrfs: fix list_add corruption and soft lockups in fsync
btrfs: Fix wild memory access in compression level parser
btrfs: fix deadlock when writing out space cache
btrfs: clear space cache inode generation always
Btrfs: fix reported number of inode blocks after buffered append writes
Btrfs: move definition of the function btrfs_find_new_delalloc_bytes
Btrfs: bail out gracefully rather than BUG_ON
btrfs: dev_alloc_list is not protected by RCU, use normal list_del
btrfs: add missing device::flush_bio puts
btrfs: Fix transaction abort during failure in btrfs_rm_dev_item
Btrfs: add write_flags for compression bio
Linus Torvalds [Wed, 29 Nov 2017 22:19:22 +0000 (14:19 -0800)]
Merge tag 'microblaze-4.15-rc2' of git://git.monstr.eu/linux-2.6-microblaze
Pull Microblaze fix from Michal Simek:
"Add missing header to mmu_context_mm.h"
* tag 'microblaze-4.15-rc2' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: add missing include to mmu_context_mm.h
Linus Torvalds [Wed, 29 Nov 2017 22:17:30 +0000 (14:17 -0800)]
Merge git://git./linux/kernel/git/davem/sparc
Pull sparc fix from David Miller:
"Sparc T4 and later cpu bootup regression fix"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix boot on T4 and later.
Linus Torvalds [Wed, 29 Nov 2017 21:10:25 +0000 (13:10 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) The forcedeth conversion from pci_*() DMA interfaces to dma_*() ones
missed one spot. From Zhu Yanjun.
2) Missing CRYPTO_SHA256 Kconfig dep in cfg80211, from Johannes Berg.
3) Fix checksum offloading in thunderx driver, from Sunil Goutham.
4) Add SPDX to vm_sockets_diag.h, from Stephen Hemminger.
5) Fix use after free of packet headers in TIPC, from Jon Maloy.
6) "sizeof(ptr)" vs "sizeof(*ptr)" bug in i40e, from Gustavo A R Silva.
7) Tunneling fixes in mlxsw driver, from Petr Machata.
8) Fix crash in fanout_demux_rollover() of AF_PACKET, from Mike
Maloney.
9) Fix race in AF_PACKET bind() vs. NETDEV_UP notifier, from Eric
Dumazet.
10) Fix regression in sch_sfq.c due to one of the timer_setup()
conversions. From Paolo Abeni.
11) SCTP does list_for_each_entry() using wrong struct member, fix from
Xin Long.
12) Don't use big endian netlink attribute read for
IFLA_BOND_AD_ACTOR_SYSTEM, it is in cpu endianness. Also from Xin
Long.
13) Fix mis-initialization of q->link.clock in CBQ scheduler, preventing
adding filters there. From Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
ethernet: dwmac-stm32: Fix copyright
net: via: via-rhine: use %p to format void * address instead of %x
net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
myri10ge: Update MAINTAINERS
net: sched: cbq: create block for q->link.block
atm: suni: remove extraneous space to fix indentation
atm: lanai: use %p to format kernel addresses instead of %x
VSOCK: Don't set sk_state to TCP_CLOSE before testing it
atm: fore200e: use %pK to format kernel addresses instead of %x
ambassador: fix incorrect indentation of assignment statement
vxlan: use __be32 type for the param vni in __vxlan_fdb_delete
bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM
sctp: use right member as the param of list_for_each_entry
sch_sfq: fix null pointer dereference at timer expiration
cls_bpf: don't decrement net's refcount when offload fails
net/packet: fix a race in packet_bind() and packet_notifier()
packet: fix crash in fanout_demux_rollover()
sctp: remove extern from stream sched
sctp: force the params with right types for sctp csum apis
sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail
...
David S. Miller [Wed, 29 Nov 2017 20:09:29 +0000 (15:09 -0500)]
sparc64: Fix boot on T4 and later.
If we don't put the NG4fls.o object into the same part of
the link as the generic sparc64 objects for fls() and __fls()
then the relocation in the branch we use for patching will
not fit.
Move NG4fls.o into lib-y to fix this problem.
Fixes:
46ad8d2d22c1 ("sparc64: Use sparc optimized fls and __fls for T4 and above")
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Tested-by: Anatoly Pugachev <matorola@gmail.com>
Linus Torvalds [Wed, 29 Nov 2017 19:28:09 +0000 (11:28 -0800)]
vsprintf: don't use 'restricted_pointer()' when not restricting
Instead, just fall back on the new '%p' behavior which hashes the
pointer.
Otherwise, '%pK' - that was intended to mark a pointer as restricted -
just ends up leaking pointers that a normal '%p' wouldn't leak. Which
just make the whole thing pointless.
I suspect we should actually get rid of '%pK' entirely, and make it just
work as '%p' regardless, but this is the minimal obvious fix. People
who actually use 'kptr_restrict' should weigh in on which behavior they
want.
Cc: Tobin Harding <me@tobin.cc>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 29 Nov 2017 18:30:13 +0000 (10:30 -0800)]
kallsyms: take advantage of the new '%px' format
The conditional kallsym hex printing used a special fixed-width '%lx'
output (KALLSYM_FMT) in preparation for the hashing of %p, but that
series ended up adding a %px specifier to help with the conversions.
Use it, and avoid the "print pointer as an unsigned long" code.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 29 Nov 2017 18:19:29 +0000 (10:19 -0800)]
Merge tag 'printk-hash-pointer-4.15-rc2' of git://github.com/tcharding/linux
Pull printk pointer hashing update from Tobin Harding:
"Here is the patch set that implements hashing of printk specifier %p.
First we have two clean up patches then we do the hashing. Hashing is
done via the SipHash algorithm. The next patch adds printk specifier
%px for printing pointers when we _really_ want to see the address i.e
%px is functionally equivalent to %lx. Final patch in the set fixes
KASAN since we break it by hashing %p.
For the record here is the justification for the series:
Currently there exist approximately 14 000 places in the Kernel
where addresses are being printed using an unadorned %p. This
potentially leaks sensitive information about the Kernel layout in
memory. Many of these calls are stale, instead of fixing every call
we hash the address by default before printing. We then add %px to
provide a way to print the actual address. Although this is
achievable using %lx, using %px will assist us if we ever want to
change pointer printing behaviour. %px is more uniquely grep'able
(there are already >50 000 uses of %lx).
The added advantage of hashing %p is that security is now opt-out,
if you _really_ want the address you have to work a little harder
and use %px.
This will of course break some users, forcing code printing needed
addresses to be updated"
[ I do expect this to be an annoyance, and a number of %px users to be
added for debuggability. But nobody is willing to audit existing %p
users for information leaks, and a number of places really only use
the pointer as an object identifier rather than really 'I need the
address'.
IOW - sorry for the inconvenience, but it's the least inconvenient of
the options. - Linus ]
* tag 'printk-hash-pointer-4.15-rc2' of git://github.com/tcharding/linux:
kasan: use %px to print addresses instead of %p
vsprintf: add printk specifier %px
printk: hash addresses printed with %p
vsprintf: refactor %pK code out of pointer()
docs: correct documentation for %pK
Linus Torvalds [Wed, 29 Nov 2017 17:01:01 +0000 (09:01 -0800)]
Revert "mm, thp: Do not make pmd/pud dirty without a reason"
This reverts commit
152e93af3cfe2d29d8136cc0a02a8612507136ee.
It was a nice cleanup in theory, but as Nicolai Stange points out, we do
need to make the page dirty for the copy-on-write case even when we
didn't end up making it writable, since the dirty bit is what we use to
check that we've gone through a COW cycle.
Reported-by: Michal Hocko <mhocko@kernel.org>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Benjamin Gaignard [Wed, 29 Nov 2017 14:20:00 +0000 (15:20 +0100)]
ethernet: dwmac-stm32: Fix copyright
Uniformize STMicroelectronics copyrights header
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
CC: Alexandre Torgue <alexandre.torgue@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Wed, 29 Nov 2017 14:11:49 +0000 (14:11 +0000)]
net: via: via-rhine: use %p to format void * address instead of %x
Don't use %x and casting to print out an address, instead use %p
and remove the casting. Cleans up smatch warnings:
drivers/net/ethernet/via/via-rhine.c:998 rhine_init_one_common()
warn: argument 4 to %lx specifier is cast from pointer
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Tue, 28 Nov 2017 17:28:52 +0000 (11:28 -0600)]
rxrpc: Fix variable overwrite
Values assigned to both variable resend_at and ack_at are overwritten
before they can be used.
The correct fix here is to add 'now' to the previously computed value in
resend_at and ack_at.
Addresses-Coverity-ID:
1462262
Addresses-Coverity-ID:
1462263
Addresses-Coverity-ID:
1462264
Fixes:
beb8e5e4f38c ("rxrpc: Express protocol timeouts in terms of RTT")
Link: https://marc.info/?i=17004.1511808959%40warthog.procyon.org.uk
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Geert Uytterhoeven [Wed, 29 Nov 2017 10:01:09 +0000 (11:01 +0100)]
net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
On 64-bit (e.g. powerpc64/allmodconfig):
drivers/net/ethernet/xilinx/ll_temac_main.c: In function 'temac_start_xmit_done':
drivers/net/ethernet/xilinx/ll_temac_main.c:633:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
dev_kfree_skb_irq((struct sk_buff *)cur_p->app4);
^
cdmac_bd.app4 is u32, so it is too small to hold a kernel pointer.
Note that several other fields in struct cdmac_bd are also too small to
hold physical addresses on 64-bit platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Wed, 29 Nov 2017 14:40:41 +0000 (14:40 +0000)]
rxrpc: Fix ACK generation from the connection event processor
Repeat terminal ACKs and now terminal ACKs are now generated from the
connection event processor rather from call handling as this allows us to
discard client call structures as soon as possible and free up the channel
for a follow on call.
However, in ACKs so generated, the additional information trailer is
malformed because the padding that's meant to be in the middle isn't
included in what's transmitted.
Fix it so that the 3 bytes of padding are included in the transmission.
Further, the trailer is misaligned because of the padding, so assigment to
the u16 and u32 fields inside it might cause problems on some arches, so
fix this by breaking the padding and the trailer out of the packed struct.
(This also deals with potential compiler weirdies where some of the nested
structs are packed and some aren't).
The symptoms can be seen in wireshark as terminal DUPLICATE or IDLE ACK
packets in which the Max MTU, Interface MTU and rwind fields have weird
values and the Max Packets field is apparently missing.
Reported-by: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Wed, 29 Nov 2017 14:25:50 +0000 (14:25 +0000)]
rxrpc: Clean up whitespace
Clean up some whitespace from rxrpc.
Signed-off-by: David Howells <dhowells@redhat.com>
Hyong-Youb Kim [Wed, 29 Nov 2017 05:03:50 +0000 (00:03 -0500)]
myri10ge: Update MAINTAINERS
Change the maintainer to Chris Lee who has access to Myricom hardware
and can test/review. Update the website URL.
Signed-off-by: Hyong-Youb Kim <hykim@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobin C. Harding [Wed, 1 Nov 2017 04:32:22 +0000 (15:32 +1100)]
kasan: use %px to print addresses instead of %p
Pointers printed with %p are now hashed by default. Kasan needs the
actual address. We can use the new printk specifier %px for this
purpose.
Use %px instead of %p to print addresses.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Tobin C. Harding [Wed, 22 Nov 2017 23:59:45 +0000 (10:59 +1100)]
vsprintf: add printk specifier %px
printk specifier %p now hashes all addresses before printing. Sometimes
we need to see the actual unmodified address. This can be achieved using
%lx but then we face the risk that if in future we want to change the
way the Kernel handles printing of pointers we will have to grep through
the already existent 50 000 %lx call sites. Let's add specifier %px as a
clear, opt-in, way to print a pointer and maintain some level of
isolation from all the other hex integer output within the Kernel.
Add printk specifier %px to print the actual unmodified address.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Tobin C. Harding [Wed, 1 Nov 2017 04:32:23 +0000 (15:32 +1100)]
printk: hash addresses printed with %p
Currently there exist approximately 14 000 places in the kernel where
addresses are being printed using an unadorned %p. This potentially
leaks sensitive information regarding the Kernel layout in memory. Many
of these calls are stale, instead of fixing every call lets hash the
address by default before printing. This will of course break some
users, forcing code printing needed addresses to be updated.
Code that _really_ needs the address will soon be able to use the new
printk specifier %px to print the address.
For what it's worth, usage of unadorned %p can be broken down as
follows (thanks to Joe Perches).
$ git grep -E '%p[^A-Za-z0-9]' | cut -f1 -d"/" | sort | uniq -c
1084 arch
20 block
10 crypto
32 Documentation
8121 drivers
1221 fs
143 include
101 kernel
69 lib
100 mm
1510 net
40 samples
7 scripts
11 security
166 sound
152 tools
2 virt
Add function ptr_to_id() to map an address to a 32 bit unique
identifier. Hash any unadorned usage of specifier %p and any malformed
specifiers.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Tobin C. Harding [Wed, 22 Nov 2017 23:56:39 +0000 (10:56 +1100)]
vsprintf: refactor %pK code out of pointer()
Currently code to handle %pK is all within the switch statement in
pointer(). This is the wrong level of abstraction. Each of the other switch
clauses call a helper function, pK should do the same.
Refactor code out of pointer() to new function restricted_pointer().
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Tobin C. Harding [Wed, 22 Nov 2017 23:55:24 +0000 (10:55 +1100)]
docs: correct documentation for %pK
Current documentation indicates that %pK prints a leading '0x'. This is
not the case.
Correct documentation for printk specifier %pK.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Linus Torvalds [Wed, 29 Nov 2017 00:22:10 +0000 (16:22 -0800)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- avoid potential bogus alignment for some AEAD operations
- fix crash in algif_aead
- avoid sleeping in softirq context with async af_alg
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: skcipher - Fix skcipher_walk_aead_common
crypto: af_alg - remove locking in async callback
crypto: algif_aead - skip SGL entries with NULL page
Jiri Pirko [Mon, 27 Nov 2017 17:37:21 +0000 (18:37 +0100)]
net: sched: cbq: create block for q->link.block
q->link.block is not initialized, that leads to EINVAL when one tries to
add filter there. So initialize it properly.
This can be reproduced by:
$ tc qdisc add dev eth0 root handle 1: cbq avpkt 1000 rate 1000Mbit bandwidth 1000Mbit
$ tc filter add dev eth0 parent 1: protocol ip prio 100 u32 match ip protocol 0 0x00 flowid 1:1
Reported-by: Jaroslav Aster <jaster@redhat.com>
Reported-by: Ivan Vecera <ivecera@redhat.com>
Fixes:
6529eaba33f0 ("net: sched: introduce tcf block infractructure")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Mon, 27 Nov 2017 13:47:22 +0000 (13:47 +0000)]
atm: suni: remove extraneous space to fix indentation
Remove a leading space, fixes indentation
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Mon, 27 Nov 2017 13:39:32 +0000 (13:39 +0000)]
atm: lanai: use %p to format kernel addresses instead of %x
Don't use %x and casting to print out a kernel address, instead use %p
and remove the casting. Cleans up smatch warnings:
drivers/atm/lanai.c:1589 service_buffer_allocate() warn: argument 2 to
%08lX specifier is cast from pointer
drivers/atm/lanai.c:2221 lanai_dev_open() warn: argument 4 to %lx
specifier is cast from pointer
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jorgen Hansen [Mon, 27 Nov 2017 13:29:32 +0000 (05:29 -0800)]
VSOCK: Don't set sk_state to TCP_CLOSE before testing it
A recent commit (
3b4477d2dcf2) converted the sk_state to use
TCP constants. In that change, vmci_transport_handle_detach
was changed such that sk->sk_state was set to TCP_CLOSE before
we test whether it is TCP_SYN_SENT. This change moves the
sk_state change back to the original locations in that function.
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Mon, 27 Nov 2017 13:24:15 +0000 (13:24 +0000)]
atm: fore200e: use %pK to format kernel addresses instead of %x
Don't use %x and casting to print out a kernel address, instead use the
%pK and remove the casting. Cleans up smatch warning:
drivers/atm/fore200e.c:3093 fore200e_proc_read() warn: argument 3 to %08x
specifier is cast from pointer
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Mon, 27 Nov 2017 13:06:10 +0000 (13:06 +0000)]
ambassador: fix incorrect indentation of assignment statement
Remove one extraneous level of indentation on assignment statement.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 26 Nov 2017 13:19:05 +0000 (21:19 +0800)]
vxlan: use __be32 type for the param vni in __vxlan_fdb_delete
All callers of __vxlan_fdb_delete pass vni with __be32 type, and
this param should be declared as __be32 type.
Fixes:
3ad7a4b141eb ("vxlan: support fdb and learning in COLLECT_METADATA mode")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 26 Nov 2017 13:12:09 +0000 (21:12 +0800)]
bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM
bond_opt_initval expects a u64 type param, it's better to use
nla_get_u64 to extract the value here, to eliminate a sparse
endianness mismatch warning.
Fixes:
171a42c38c6e ("bonding: add netlink support for sys prio, actor sys mac, and port key")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 26 Nov 2017 12:56:07 +0000 (20:56 +0800)]
sctp: use right member as the param of list_for_each_entry
Commit
d04adf1b3551 ("sctp: reset owner sk for data chunks on out queues
when migrating a sock") made a mistake that using 'list' as the param of
list_for_each_entry to traverse the retransmit, sacked and abandoned
queues, while chunks are using 'transmitted_list' to link into these
queues.
It could cause NULL dereference panic if there are chunks in any of these
queues when peeling off one asoc.
So use the chunk member 'transmitted_list' instead in this patch.
Fixes:
d04adf1b3551 ("sctp: reset owner sk for data chunks on out queues when migrating a sock")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 28 Nov 2017 13:28:39 +0000 (14:28 +0100)]
sch_sfq: fix null pointer dereference at timer expiration
While converting sch_sfq to use timer_setup(), the commit
cdeabbb88134
("net: sched: Convert timers to use timer_setup()") forgot to
initialize the 'sch' field. As a result, the timer callback tries to
dereference a NULL pointer, and the kernel does oops.
Fix it initializing such field at qdisc creation time.
Fixes:
cdeabbb88134 ("net: sched: Convert timers to use timer_setup()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 27 Nov 2017 19:11:41 +0000 (11:11 -0800)]
cls_bpf: don't decrement net's refcount when offload fails
When cls_bpf offload was added it seemed like a good idea to
call cls_bpf_delete_prog() instead of extending the error
handling path, since the software state is fully initialized
at that point. This handling of errors without jumping to
the end of the function is error prone, as proven by later
commit missing that extra call to __cls_bpf_delete_prog().
__cls_bpf_delete_prog() is now expected to be invoked with
a reference on exts->net or the field zeroed out. The call
on the offload's error patch does not fullfil this requirement,
leading to each error stealing a reference on net namespace.
Create a function undoing what cls_bpf_set_parms() did and
use it from __cls_bpf_delete_prog() and the error path.
Fixes:
aae2c35ec892 ("cls_bpf: use tcf_exts_get_net() before call_rcu()")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 28 Nov 2017 18:01:15 +0000 (10:01 -0800)]
Merge tag 'drm-for-v4.15-part2-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
- TTM regression fix for some virt gpus (bochs vga)
- a few i915 stable fixes
- one vc4 fix
- one uapi fix
* tag 'drm-for-v4.15-part2-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/ttm: don't attempt to use hugepages if dma32 requested (v2)
drm/vblank: Pass crtc_id to page_flip_ioctl.
drm/i915: Fix init_clock_gating for resume
drm/i915: Mark the userptr invalidate workqueue as WQ_MEM_RECLAIM
drm/i915: Clear breadcrumb node when cancelling signaling
drm/i915/gvt: ensure -ve return value is handled correctly
drm/i915: Re-register PMIC bus access notifier on runtime resume
drm/i915: Fix false-positive assert_rpm_wakelock_held in i915_pmic_bus_access_notifier v2
drm/edid: Don't send non-zero YQ in AVI infoframe for HDMI 1.x sinks
drm/vc4: Account for interrupts in flight
Takashi Iwai [Mon, 27 Nov 2017 09:59:40 +0000 (10:59 +0100)]
Revert "ALSA: usb-audio: Fix potential zero-division at parsing FU"
The commit
8428a8ebde2d ("ALSA: usb-audio: Fix potential zero-division
at parsing FU") is utterly bogus and breaks the case with csize=1
instead of fixing anything. Just take it back again.
Reported-by: Jörg Otte <jrg.otte@gmail.com>
Fixes:
8428a8ebde2d ("ALSA: usb-audio: Fix potential zero-division at parsing FU"
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Filipe Manana [Fri, 17 Nov 2017 01:54:00 +0000 (01:54 +0000)]
Btrfs: incremental send, fix wrong unlink path after renaming file
Under some circumstances, an incremental send operation can issue wrong
paths for unlink commands related to files that have multiple hard links
and some (or all) of those links were renamed between the parent and send
snapshots. Consider the following example:
Parent snapshot
. (ino 256)
|---- a/ (ino 257)
| |---- b/ (ino 259)
| | |---- c/ (ino 260)
| | |---- f2 (ino 261)
| |
| |---- f2l1 (ino 261)
|
|---- d/ (ino 262)
|---- f1l1_2 (ino 258)
|---- f2l2 (ino 261)
|---- f1_2 (ino 258)
Send snapshot
. (ino 256)
|---- a/ (ino 257)
| |---- f2l1/ (ino 263)
| |---- b2/ (ino 259)
| |---- c/ (ino 260)
| | |---- d3 (ino 262)
| | |---- f1l1_2 (ino 258)
| | |---- f2l2_2 (ino 261)
| | |---- f1_2 (ino 258)
| |
| |---- f2 (ino 261)
| |---- f1l2 (ino 258)
|
|---- d (ino 261)
When computing the incremental send stream the following steps happen:
1) When processing inode 261, a rename operation is issued that renames
inode 262, which currently as a path of "d", to an orphan name of
"o262-7-0". This is done because in the send snapshot, inode 261 has
of its hard links with a path of "d" as well.
2) Two link operations are issued that create the new hard links for
inode 261, whose names are "d" and "f2l2_2", at paths "/" and
"o262-7-0/" respectively.
3) Still while processing inode 261, unlink operations are issued to
remove the old hard links of inode 261, with names "f2l1" and "f2l2",
at paths "a/" and "d/". However path "d/" does not correspond anymore
to the directory inode 262 but corresponds instead to a hard link of
inode 261 (link command issued in the previous step). This makes the
receiver fail with a ENOTDIR error when attempting the unlink
operation.
The problem happens because before sending the unlink operation, we failed
to detect that inode 262 was one of ancestors for inode 261 in the parent
snapshot, and therefore we didn't recompute the path for inode 262 before
issuing the unlink operation for the link named "f2l2" of inode 262. The
detection failed because the function "is_ancestor()" only follows the
first hard link it finds for an inode instead of all of its hard links
(as it was originally created for being used with directories only, for
which only one hard link exists). So fix this by making "is_ancestor()"
follow all hard links of the input inode.
A test case for fstests follows soon.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Eric Dumazet [Tue, 28 Nov 2017 16:03:30 +0000 (08:03 -0800)]
net/packet: fix a race in packet_bind() and packet_notifier()
syzbot reported crashes [1] and provided a C repro easing bug hunting.
When/if packet_do_bind() calls __unregister_prot_hook() and releases
po->bind_lock, another thread can run packet_notifier() and process an
NETDEV_UP event.
This calls register_prot_hook() and hooks again the socket right before
first thread is able to grab again po->bind_lock.
Fixes this issue by temporarily setting po->num to 0, as suggested by
David Miller.
[1]
dev_remove_pack:
ffff8801bf16fa80 not found
------------[ cut here ]------------
kernel BUG at net/core/dev.c:7945! ( BUG_ON(!list_empty(&dev->ptype_all)); )
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
device syz0 entered promiscuous mode
CPU: 0 PID: 3161 Comm: syzkaller404108 Not tainted 4.14.0+ #190
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
task:
ffff8801cc57a500 task.stack:
ffff8801cc588000
RIP: 0010:netdev_run_todo+0x772/0xae0 net/core/dev.c:7945
RSP: 0018:
ffff8801cc58f598 EFLAGS:
00010293
RAX:
ffff8801cc57a500 RBX:
dffffc0000000000 RCX:
ffffffff841f75b2
RDX:
0000000000000000 RSI:
1ffff100398b1ede RDI:
ffff8801bf1f8810
device syz0 entered promiscuous mode
RBP:
ffff8801cc58f898 R08:
0000000000000001 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000000 R12:
ffff8801bf1f8cd8
R13:
ffff8801cc58f870 R14:
ffff8801bf1f8780 R15:
ffff8801cc58f7f0
FS:
0000000001716880(0000) GS:
ffff8801db400000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000020b13000 CR3:
0000000005e25000 CR4:
00000000001406f0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
rtnl_unlock+0xe/0x10 net/core/rtnetlink.c:106
tun_detach drivers/net/tun.c:670 [inline]
tun_chr_close+0x49/0x60 drivers/net/tun.c:2845
__fput+0x333/0x7f0 fs/file_table.c:210
____fput+0x15/0x20 fs/file_table.c:244
task_work_run+0x199/0x270 kernel/task_work.c:113
exit_task_work include/linux/task_work.h:22 [inline]
do_exit+0x9bb/0x1ae0 kernel/exit.c:865
do_group_exit+0x149/0x400 kernel/exit.c:968
SYSC_exit_group kernel/exit.c:979 [inline]
SyS_exit_group+0x1d/0x20 kernel/exit.c:977
entry_SYSCALL_64_fastpath+0x1f/0x96
RIP: 0033:0x44ad19
Fixes:
30f7ea1c2b5f ("packet: race condition in packet_bind")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Francesco Ruggeri <fruggeri@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Maloney [Tue, 28 Nov 2017 15:44:29 +0000 (10:44 -0500)]
packet: fix crash in fanout_demux_rollover()
syzkaller found a race condition fanout_demux_rollover() while removing
a packet socket from a fanout group.
po->rollover is read and operated on during packet_rcv_fanout(), via
fanout_demux_rollover(), but the pointer is currently cleared before the
synchronization in packet_release(). It is safer to delay the cleanup
until after synchronize_net() has been called, ensuring all calls to
packet_rcv_fanout() for this socket have finished.
To further simplify synchronization around the rollover structure, set
po->rollover in fanout_add() only if there are no errors. This removes
the need for rcu in the struct and in the call to
packet_getsockopt(..., PACKET_ROLLOVER_STATS, ...).
Crashing stack trace:
fanout_demux_rollover+0xb6/0x4d0 net/packet/af_packet.c:1392
packet_rcv_fanout+0x649/0x7c8 net/packet/af_packet.c:1487
dev_queue_xmit_nit+0x835/0xc10 net/core/dev.c:1953
xmit_one net/core/dev.c:2975 [inline]
dev_hard_start_xmit+0x16b/0xac0 net/core/dev.c:2995
__dev_queue_xmit+0x17a4/0x2050 net/core/dev.c:3476
dev_queue_xmit+0x17/0x20 net/core/dev.c:3509
neigh_connected_output+0x489/0x720 net/core/neighbour.c:1379
neigh_output include/net/neighbour.h:482 [inline]
ip6_finish_output2+0xad1/0x22a0 net/ipv6/ip6_output.c:120
ip6_finish_output+0x2f9/0x920 net/ipv6/ip6_output.c:146
NF_HOOK_COND include/linux/netfilter.h:239 [inline]
ip6_output+0x1f4/0x850 net/ipv6/ip6_output.c:163
dst_output include/net/dst.h:459 [inline]
NF_HOOK.constprop.35+0xff/0x630 include/linux/netfilter.h:250
mld_sendpack+0x6a8/0xcc0 net/ipv6/mcast.c:1660
mld_send_initial_cr.part.24+0x103/0x150 net/ipv6/mcast.c:2072
mld_send_initial_cr net/ipv6/mcast.c:2056 [inline]
ipv6_mc_dad_complete+0x99/0x130 net/ipv6/mcast.c:2079
addrconf_dad_completed+0x595/0x970 net/ipv6/addrconf.c:4039
addrconf_dad_work+0xac9/0x1160 net/ipv6/addrconf.c:3971
process_one_work+0xbf0/0x1bc0 kernel/workqueue.c:2113
worker_thread+0x223/0x1990 kernel/workqueue.c:2247
kthread+0x35e/0x430 kernel/kthread.c:231
ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:432
Fixes:
0648ab70afe6 ("packet: rollover prepare: per-socket state")
Fixes:
509c7a1ecc860 ("packet: avoid panic in packet_getsockopt()")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Mike Maloney <maloney@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 28 Nov 2017 16:00:14 +0000 (11:00 -0500)]
Merge branch 'sctp-fix-sparse-errors'
Xin Long says:
====================
sctp: fix some other sparse errors
After the last fixes for sparse errors, there are still three sparse
errors in sctp codes, two of them are type cast, and the other one
is using extern.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 26 Nov 2017 12:16:08 +0000 (20:16 +0800)]
sctp: remove extern from stream sched
Now each stream sched ops is defined in different .c file and
added into the global ops in another .c file, it uses extern
to make this work.
However extern is not good coding style to get them in and
even make C=2 reports errors for this.
This patch adds sctp_sched_ops_xxx_init for each stream sched
ops in their .c file, then get them into the global ops by
calling them when initializing sctp module.
Fixes:
637784ade221 ("sctp: introduce priority based stream scheduler")
Fixes:
ac1ed8b82cd6 ("sctp: introduce round robin stream scheduler")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 26 Nov 2017 12:16:07 +0000 (20:16 +0800)]
sctp: force the params with right types for sctp csum apis
Now sctp_csum_xxx doesn't really match the param types of these common
csum apis. As sctp_csum_xxx is defined in sctp/checksum.h, many sparse
errors occur when make C=2 not only with M=net/sctp but also with other
modules that include this header file.
This patch is to force them fit in csum apis with the right types.
Fixes:
e6d8b64b34aa ("net: sctp: fix and consolidate SCTP checksumming code")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 26 Nov 2017 12:16:06 +0000 (20:16 +0800)]
sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail
This patch is to force SCTP_ERROR_INV_STRM with right type to
fit in sctp_chunk_fail to avoid the sparse error.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasyl Gomonovych [Wed, 22 Nov 2017 15:29:57 +0000 (16:29 +0100)]
lmc: Use memdup_user() as a cleanup
Fix coccicheck warning which recommends to use memdup_user():
drivers/net/wan/lmc/lmc_main.c:497:27-34: WARNING opportunity for memdup_user
Generated by: scripts/coccinelle/memdup_user/memdup_user.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Tue, 21 Nov 2017 19:46:49 +0000 (20:46 +0100)]
bnxt_en: Fix an error handling path in 'bnxt_get_module_eeprom()'
Error code returned by 'bnxt_read_sfp_module_eeprom_info()' is handled a
few lines above when reading the A0 portion of the EEPROM.
The same should be done when reading the A2 portion of the EEPROM.
In order to correctly propagate an error, update 'rc' in this 2nd call as
well, otherwise 0 (success) is returned.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Tue, 28 Nov 2017 13:26:30 +0000 (14:26 +0100)]
net: phy: marvell10g: fix the PHY id mask
The Marvell 10G PHY driver supports different hardware revisions, which
have their bits 3..0 differing. To get the correct revision number these
bits should be ignored. This patch fixes this by using the already
defined MARVELL_PHY_ID_MASK (0xfffffff0) instead of the custom
0xffffffff mask.
Fixes:
20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 28 Nov 2017 15:09:52 +0000 (10:09 -0500)]
Merge branch 'mvpp2-fixes'
Antoine Tenart says:
====================
net: mvpp2: set of fixes
This series fixes various issues with the Marvell PPv2 driver. The
patches are sent together to avoid any possible conflict. The series is
based on today's net tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Tue, 28 Nov 2017 13:19:51 +0000 (14:19 +0100)]
net: mvpp2: check ethtool sets the Tx ring size is to a valid min value
This patch fixes the Tx ring size checks when using ethtool, by adding
an extra check in the PPv2 check_ringparam_valid helper. The Tx ring
size cannot be set to a value smaller than the minimum number of
descriptors needed for TSO.
Fixes:
1d17db08c056 ("net: mvpp2: limit TSO segments and use stop/wake thresholds")
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yan Markman [Tue, 28 Nov 2017 13:19:50 +0000 (14:19 +0100)]
net: mvpp2: do not disable GMAC padding
Short fragmented packets may never be sent by the hardware when padding
is disabled. This patch stop modifying the GMAC padding bits, to leave
them to their reset value (disabled).
Fixes:
3919357fb0bb ("net: mvpp2: initialize the GMAC when using a port")
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Tue, 28 Nov 2017 13:19:49 +0000 (14:19 +0100)]
net: mvpp2: cleanup probed ports in the probe error path
This patches fixes the probe error path by cleaning up probed ports, to
avoid leaving registered net devices when the driver failed to probe.
Fixes:
3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Tue, 28 Nov 2017 13:19:48 +0000 (14:19 +0100)]
net: mvpp2: fix the txq_init error path
When an allocation in the txq_init path fails, the allocated buffers
end-up being freed twice: in the txq_init error path, and in txq_deinit.
This lead to issues as txq_deinit would work on already freed memory
regions:
kernel BUG at mm/slub.c:3915!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
This patch fixes this by removing the txq_init own error path, as the
txq_deinit function is always called on errors. This was introduced by
TSO as way more buffers are allocated.
Fixes:
186cd4d4e414 ("net: mvpp2: software tso support")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 28 Nov 2017 14:55:48 +0000 (09:55 -0500)]
Merge branch 'mlxsw-GRE-offloading-fixes'
Jiri Pirko says:
====================
mlxsw: GRE offloading fixes
Petr says:
This patchset fixes a couple bugs in offloading GRE tunnels in mlxsw
driver.
Patch #1 fixes a problem that local routes pointing at a GRE tunnel
device are offloaded even if that netdevice is down.
Patch #2 detects that as a result of moving a GRE netdevice to a
different VRF, two tunnels now have a conflict of local addresses,
something that the mlxsw driver can't offload.
Patch #3 fixes a FIB abort caused by forming a route pointing at a
GRE tunnel that is eligible for offloading but already onloaded.
Patch #4 fixes a problem that next hops migrated to a new RIF kept the
old RIF reference, which went dangling shortly afterwards.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Tue, 28 Nov 2017 12:17:14 +0000 (13:17 +0100)]
mlxsw: spectrum_router: Update nexthop RIF on update
The function mlxsw_sp_nexthop_rif_update() walks the list of nexthops
associated with a RIF, and updates the corresponding entries in the
switch. It is used in particular when a tunnel underlay netdevice moves
to a different VRF, and all the nexthops are migrated over to a new RIF.
The problem is that each nexthop holds a reference to its RIF, and that
is not updated. So after the old RIF is gone, further activity on these
nexthops (such as downing the underlay netdevice) dereferences a
dangling pointer.
Fix the issue by updating rif of impacted nexthops before calling
mlxsw_sp_nexthop_rif_update().
Fixes:
0c5f1cd5ba8c ("mlxsw: spectrum_router: Generalize __mlxsw_sp_ipip_entry_update_tunnel()")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Tue, 28 Nov 2017 12:17:13 +0000 (13:17 +0100)]
mlxsw: spectrum_router: Handle encap to demoted tunnels
Some tunnels that are offloadable on their own can nonetheless be
demoted to slow path if their local address is in conflict with that of
another tunnel. When a route is formed for such a tunnel,
mlxsw_sp_nexthop_ipip_init() fails to find the corresponding IPIP entry,
and that triggers a FIB abort.
Resolve the problem by not assuming that a tunnel for which
mlxsw_sp_ipip_ops.can_offload() holds also automatically has an IPIP
entry.
Fixes:
af641713e97d ("mlxsw: spectrum_router: Onload conflicting tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Tue, 28 Nov 2017 12:17:12 +0000 (13:17 +0100)]
mlxsw: spectrum_router: Demote tunnels on VRF migration
The mlxsw driver currently doesn't offload GRE tunnels if they have the
same local address and use the same underlay VRF. When such a situation
arises, the tunnels in conflict are demoted to slow path.
However, the current code only verifies this condition on tunnel
creation and tunnel change, not when a tunnel is moved to a different
VRF. When the tunnel has no bound device, underlay and overlay are the
same. Thus moving a tunnel moves the underlay as well, and that can
cause local address conflict.
So modify mlxsw_sp_netdevice_ipip_ol_vrf_event() to check if there are
any conflicting tunnels, and demote them if yes.
Fixes:
af641713e97d ("mlxsw: spectrum_router: Onload conflicting tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Tue, 28 Nov 2017 12:17:11 +0000 (13:17 +0100)]
mlxsw: spectrum_router: Offload decap only for up tunnels
When a new local route is added, an IPIP entry is looked up to determine
whether the route should be offloaded as a tunnel decap or as a trap.
That decision should take into account whether the tunnel netdevice in
question is actually IFF_UP, and only install a decap offload if it is.
Fixes:
0063587d3587 ("mlxsw: spectrum: Support decap-only IP-in-IP tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 28 Nov 2017 14:52:04 +0000 (09:52 -0500)]
Merge branch '40GbE' of git://git./linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2017-11-27
This series contains updates to e1000, e1000e and i40e.
Gustavo A. R. Silva fixes a sizeof() issue where we were taking the size of
the pointer (which is always the size of the pointer).
Sasha does a follow up fix to a previous fix for buffer overrun, to resolve
community feedback from David Laight and the use of magic numbers.
Amritha fixes the reporting of error codes for when adding a cloud filter
fails.
Ahmad Fatoum brushes the dust off the e1000 driver to fix a code comment
and debug message which was incorrect about what the code was really doing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Qu Wenruo [Wed, 8 Nov 2017 00:54:24 +0000 (08:54 +0800)]
btrfs: tree-checker: Fix false panic for sanity test
[BUG]
If we run btrfs with CONFIG_BTRFS_FS_RUN_SANITY_TESTS=y, it will
instantly cause kernel panic like:
------
...
assertion failed: 0, file: fs/btrfs/disk-io.c, line: 3853
...
Call Trace:
btrfs_mark_buffer_dirty+0x187/0x1f0 [btrfs]
setup_items_for_insert+0x385/0x650 [btrfs]
__btrfs_drop_extents+0x129a/0x1870 [btrfs]
...
-----
[Cause]
Btrfs will call btrfs_check_leaf() in btrfs_mark_buffer_dirty() to check
if the leaf is valid with CONFIG_BTRFS_FS_RUN_SANITY_TESTS=y.
However quite some btrfs_mark_buffer_dirty() callers(*) don't really
initialize its item data but only initialize its item pointers, leaving
item data uninitialized.
This makes tree-checker catch uninitialized data as error, causing
such panic.
*: These callers include but not limited to
setup_items_for_insert()
btrfs_split_item()
btrfs_expand_item()
[Fix]
Add a new parameter @check_item_data to btrfs_check_leaf().
With @check_item_data set to false, item data check will be skipped and
fallback to old btrfs_check_leaf() behavior.
So we can still get early warning if we screw up item pointers, and
avoid false panic.
Cc: Filipe Manana <fdmanana@gmail.com>
Reported-by: Lakshmipathi.G <lakshmipathi.g@gmail.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Linus Torvalds [Tue, 28 Nov 2017 00:45:56 +0000 (16:45 -0800)]
proc: don't report kernel addresses in /proc/<pid>/stack
This just changes the file to report them as zero, although maybe even
that could be removed. I checked, and at least procps doesn't actually
seem to parse the 'stack' file at all.
And since the file doesn't necessarily even exist (it requires
CONFIG_STACKTRACE), possibly other tools don't really use it either.
That said, in case somebody parses it with tools, just having that zero
there should keep such tools happy.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ahmad Fatoum [Sat, 18 Nov 2017 20:53:58 +0000 (21:53 +0100)]
e1000: Fix off-by-one in debug message
Signed-off-by: Ahmad Fatoum <ahmad@a3f.at>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Amritha Nambiar [Fri, 17 Nov 2017 23:35:57 +0000 (15:35 -0800)]
i40e: Fix reporting incorrect error codes
Adding cloud filters could fail for a number of reasons,
unsupported filter fields for example, which fails during
validation of fields itself. This will not result in admin
command errors and converting the admin queue status to posix
error code using i40e_aq_rc_to_posix would result in incorrect
error values. If the failure was due to AQ error itself,
reporting that correctly is handled in the inner function.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Mon, 6 Nov 2017 06:31:59 +0000 (08:31 +0200)]
e1000e: fix the use of magic numbers for buffer overrun issue
This is a follow on to commit
b10effb92e27 ("fix buffer overrun while the
I219 is processing DMA transactions") to address David Laights concerns
about the use of "magic" numbers. So define masks as well as add
additional code comments to give a better understanding of what needs to
be done to avoid a buffer overrun.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Alexander H Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Gustavo A R Silva [Wed, 18 Oct 2017 20:34:25 +0000 (15:34 -0500)]
i40e/virtchnl: fix application of sizeof to pointer
sizeof when applied to a pointer typed expression gives the size of
the pointer.
The proper fix in this particular case is to code sizeof(*vfres)
instead of sizeof(vfres).
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A R Silva <garsilva@embeddedor.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Vasily Averin [Mon, 13 Nov 2017 04:25:40 +0000 (07:25 +0300)]
lockd: fix "list_add double add" caused by legacy signal interface
restart_grace() uses hardcoded init_net.
It can cause to "list_add double add" in following scenario:
1) nfsd and lockd was started in several net namespaces
2) nfsd in init_net was stopped (lockd was not stopped because
it have users from another net namespaces)
3) lockd got signal, called restart_grace() -> set_grace_period()
and enabled lock_manager in hardcoded init_net.
4) nfsd in init_net is started again,
its lockd_up() calls set_grace_period() and tries to add
lock_manager into init_net 2nd time.
Jeff Layton suggest:
"Make it safe to call locks_start_grace multiple times on the same
lock_manager. If it's already on the global grace_list, then don't try
to add it again. (But we don't intentionally add twice, so for now we
WARN about that case.)
With this change, we also need to ensure that the nfsd4 lock manager
initializes the list before we call locks_start_grace. While we're at
it, move the rest of the nfsd_net initialization into
nfs4_state_create_net. I see no reason to have it spread over two
functions like it is today."
Suggested patch was updated to generate warning in described situation.
Suggested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Vasily Averin [Mon, 30 Oct 2017 13:47:58 +0000 (16:47 +0300)]
nlm_shutdown_hosts_net() cleanup
nlm_complain_hosts() walks through nlm_server_hosts hlist, which should
be protected by nlm_host_mutex.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>