OSDN Git Service
Jaime Caamaño Ruiz [Wed, 31 Oct 2018 17:52:03 +0000 (18:52 +0100)]
openvswitch: Fix push/pop ethernet validation
When there are both pop and push ethernet header actions among the
actions to be applied to a packet, an unexpected EINVAL (Invalid
argument) error is obtained. This is due to mac_proto not being reset
correctly when those actions are validated.
Reported-at:
https://mail.openvswitch.org/pipermail/ovs-discuss/2018-October/047554.html
Fixes:
91820da6ae85 ("openvswitch: add Ethernet push and pop actions")
Signed-off-by: Jaime Caamaño Ruiz <jcaamano@suse.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 31 Oct 2018 15:08:10 +0000 (16:08 +0100)]
net: stmmac: Fix stmmac_mdio_reset() when building stmmac as modules
When building stmmac, it is only possible to select CONFIG_DWMAC_GENERIC,
or any of the glue drivers, when CONFIG_STMMAC_PLATFORM is set.
The only exception is CONFIG_STMMAC_PCI.
When calling of_mdiobus_register(), it will call our ->reset()
callback, which is set to stmmac_mdio_reset().
Most of the code in stmmac_mdio_reset() is protected by a
"#if defined(CONFIG_STMMAC_PLATFORM)", which will evaluate
to false when CONFIG_STMMAC_PLATFORM=m.
Because of this, the phy reset gpio will only be pulled when
stmmac is built as built-in, but not when built as modules.
Fix this by using "#if IS_ENABLED()" instead of "#if defined()".
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 1 Nov 2018 01:21:37 +0000 (18:21 -0700)]
Merge branch '10GbE' of git://git./linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-10-31
This series contains a various collection of fixes.
Miroslav Lichvar from Red Hat or should I say IBM now? Updates the PHC
timecounter interval for igb so that it gets updated at least once
every 550 seconds.
Ngai-Mint provides a fix for fm10k to prevent a soft lockup or system
crash by adding a new condition to determine if the SM mailbox is in the
correct state before proceeding.
Jake provides several fm10k fixes, first one marks complier aborts as
non-fatal since on some platforms trigger machine check errors when the
compile aborts. Added missing device ids to the in-kernel driver. Due
to the recent fixes, bumped the driver version.
I (Jeff Kirsher) fixed a XFRM_ALGO dependency for both ixgbe and
ixgbevf. This fix was based on the original work from Arnd Bergmann,
which only fixed ixgbe.
Mitch provides a fix for i40e/avf to update the status codes, which
resolves an issue between a mis-match between i40e and the iavf driver,
which also supports the ice LAN driver.
Radoslaw fixes the ixgbe where the driver is logging a message about
spoofed packets detected when the VF is re-started with a different MAC
address.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 1 Nov 2018 00:34:08 +0000 (17:34 -0700)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2018-11-01
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix tcp_bpf_recvmsg() to return -EAGAIN instead of 0 in non-blocking
case when no data is available yet, from John.
2) Fix a compilation error in libbpf_attach_type_by_name() when compiled
with clang 3.8, from Andrey.
3) Fix a partial copy of map pointer on scalar alu and remove id
generation for RET_PTR_TO_MAP_VALUE return types, from Daniel.
4) Add unlimited memlock limit for kernel selftest's flow_dissector_load
program, from Yonghong.
5) Fix ping for some BPF shell based kselftests where distro does not
ship "ping -6" anymore, from Li.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov [Wed, 31 Oct 2018 23:53:18 +0000 (16:53 -0700)]
Merge branch 'verifier-fixes'
Daniel Borkmann says:
====================
The series contains two fixes in BPF core and test cases. For details
please see individual patches. Thanks!
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann [Wed, 31 Oct 2018 23:05:55 +0000 (00:05 +0100)]
bpf: test make sure to run unpriv test cases in test_verifier
Right now unprivileged tests are never executed as a BPF test run,
only loaded. Allow for running them as well so that we can check
the outcome and probe for regressions.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann [Wed, 31 Oct 2018 23:05:54 +0000 (00:05 +0100)]
bpf: add various test cases to test_verifier
Add some more map related test cases to test_verifier kselftest
to improve test coverage. Summary: 1012 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann [Wed, 31 Oct 2018 23:05:53 +0000 (00:05 +0100)]
bpf: don't set id on after map lookup with ptr_to_map_val return
In the verifier there is no such semantics where registers with
PTR_TO_MAP_VALUE type have an id assigned to them. This is only
used in PTR_TO_MAP_VALUE_OR_NULL and later on nullified once the
test against NULL has been pattern matched and type transformed
into PTR_TO_MAP_VALUE.
Fixes:
3e6a4b3e0289 ("bpf/verifier: introduce BPF_PTR_TO_MAP_VALUE")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Roman Gushchin <guro@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann [Wed, 31 Oct 2018 23:05:52 +0000 (00:05 +0100)]
bpf: fix partial copy of map_ptr when dst is scalar
ALU operations on pointers such as scalar_reg += map_value_ptr are
handled in adjust_ptr_min_max_vals(). Problem is however that map_ptr
and range in the register state share a union, so transferring state
through dst_reg->range = ptr_reg->range is just buggy as any new
map_ptr in the dst_reg is then truncated (or null) for subsequent
checks. Fix this by adding a raw member and use it for copying state
over to dst_reg.
Fixes:
f1174f77b50c ("bpf/verifier: rework value tracking")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Edward Cree <ecree@solarflare.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Andrey Ignatov [Wed, 31 Oct 2018 19:57:18 +0000 (12:57 -0700)]
libbpf: Fix compile error in libbpf_attach_type_by_name
Arnaldo Carvalho de Melo reported build error in libbpf when clang
version 3.8.1-24 (tags/RELEASE_381/final) is used:
libbpf.c:2201:36: error: comparison of constant -22 with expression of
type 'const enum bpf_attach_type' is always false
[-Werror,-Wtautological-constant-out-of-range-compare]
if (section_names[i].attach_type == -EINVAL)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ^ ~~~~~~~
1 error generated.
Fix the error by keeping "is_attachable" property of a program in a
separate struct field instead of trying to use attach_type itself.
Fixes:
956b620fcf0b ("libbpf: Introduce libbpf_attach_type_by_name")
Reported-by: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Li Zhijian [Tue, 30 Oct 2018 03:15:55 +0000 (11:15 +0800)]
kselftests/bpf: use ping6 as the default ipv6 ping binary if it exists
ping binary on some distros doesn't support "ping -6" anymore.
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
David S. Miller [Wed, 31 Oct 2018 19:56:59 +0000 (12:56 -0700)]
Merge branch 'mlxsw-Enable-minimum-shaper-on-MC-TCs'
Ido Schimmel says:
====================
mlxsw: Enable minimum shaper on MC TCs
Petr says:
An MC-aware mode was introduced in commit
7b8195306694 ("mlxsw:
spectrum: Configure MC-aware mode on mlxsw ports"). In MC-aware mode,
BUM traffic gets a special treatment by being assigned to a separate set
of traffic classes 8..15. Pairs of TCs 0 and 8, 1 and 9, etc., are then
configured to strictly prioritize the lower-numbered ones. The intention
is to prevent BUM traffic from flooding the switch and push out all UC
traffic, which would otherwise happen, and instead give UC traffic
precedence.
However strictly prioritizing UC traffic has the effect that UC overload
pushes out all BUM traffic, such as legitimate ARP queries. These
packets are kept in queues for a while, but under sustained UC overload,
their lifetime eventually expires and these packets are dropped. That is
detrimental to network performance as well.
In this patchset, MC TCs (8..15) are configured with minimum shaper of
200Mbps (a minimum permitted value) to allow a trickle of necessary
control traffic to get through.
First in patch #1, the QEEC register is extended with fields necessary
to configure the minimum shaper.
In patch #2, minimum shaper is enabled on TCs 8..15.
In patches #3 and #4, first the MC-awareness test is tweaked to support
the minimum shaper, and then a new test is introduced to test that MC
traffic behaves well under UC overload.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Wed, 31 Oct 2018 09:56:46 +0000 (09:56 +0000)]
selftests: mlxsw: qos_mc_aware: Add a test for UC awareness
In a previous patch, mlxsw was updated to configure a minimum bandwidth
allowance on MC TCs. Test that this indeed fixes the problem of UC
traffic overload pushing out all MC traffic.
Fixes:
b5638d46c90a ("selftests: mlxsw: Add a test for UC behavior under MC flood")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Wed, 31 Oct 2018 09:56:45 +0000 (09:56 +0000)]
selftests: mlxsw: qos_mc_aware: Tweak for min shaper
Since the minimum shaper is now being enabled for MC TCs, it's
unreasonable to expect no UC traffic loss. Minimal min shaper value is
200Mbps, which is 20% of the 1Gbps that this test configures on egress.
To cover for glitches, tolerate up to 25% UC degradation under MC
overload.
Fixes:
b5638d46c90a ("selftests: mlxsw: Add a test for UC behavior under MC flood")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Wed, 31 Oct 2018 09:56:44 +0000 (09:56 +0000)]
mlxsw: spectrum: Set minimum shaper on MC TCs
An MC-aware mode was introduced in commit
7b8195306694 ("mlxsw:
spectrum: Configure MC-aware mode on mlxsw ports"). In MC-aware mode,
BUM traffic gets a special treatment by being assigned to a separate set
of traffic classes 8..15. Pairs of TCs 0 and 8, 1 and 9, etc., are then
configured to strictly prioritize the lower-numbered ones. The intention
is to prevent BUM traffic from flooding the switch and push out all UC
traffic, which would otherwise happen, and instead give UC traffic
precedence.
However strictly prioritizing UC traffic has the effect that UC overload
pushes out all BUM traffic, such as legitimate ARP queries. These
packets are kept in queues for a while, but under sustained UC overload,
their lifetime eventually expires and these packets are dropped. That is
detrimental to network performance as well.
Therefore configure the MC TCs (8..15) with minimum shaper of 200Mbps (a
minimum permitted value) to allow a trickle of necessary control traffic
to get through.
Fixes:
7b8195306694 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Wed, 31 Oct 2018 09:56:42 +0000 (09:56 +0000)]
mlxsw: reg: QEEC: Add minimum shaper fields
Add QEEC.mise (minimum shaper enable) and QEEC.min_shaper_rate to enable
configuration of minimum shaper.
Increase the QEEC length to 0x20 as well: that's the length that the
register has had for a long time now, but with the configurations that
mlxsw typically exercises, the firmware tolerated 0x1C-sized packets.
With mise=true however, FW rejects packets unless they have the full
required length.
Fixes:
b9b7cee40579 ("mlxsw: reg: Add QoS ETS Element Configuration register")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 31 Oct 2018 19:42:39 +0000 (12:42 -0700)]
Merge branch 'hns3-fixes'
Huazhong Tan says:
====================
Bugfix for the HNS3 driver
This patch series include bugfix for the HNS3 ethernet
controller driver.
Change log:
V4->V5:
Fixes comments from Joe Perches & Sergei Shtylyov
V3->V4:
Fixes comments from Sergei Shtylyov
V2->V3:
Fixes comments from Sergei Shtylyov
V1->V2:
Fixes the compilation break reported by kbuild test robot
http://patchwork.ozlabs.org/patch/989818/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Tue, 30 Oct 2018 13:50:53 +0000 (21:50 +0800)]
net: hns3: bugfix for rtnl_lock's range in the hclgevf_reset()
Since hclgevf_reset_wait() is used to wait for the hardware to complete
the reset, it is not necessary to hold the rtnl_lock during
hclgevf_reset_wait(). So this patch releases the lock for the duration
of hclgevf_reset_wait().
Fixes:
6988eb2a9b77 ("net: hns3: Add support to reset the enet/ring mgmt layer")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Tue, 30 Oct 2018 13:50:52 +0000 (21:50 +0800)]
net: hns3: bugfix for rtnl_lock's range in the hclge_reset()
Since hclge_reset_wait() is used to wait for the hardware to complete
the reset, it is not necessary to hold the rtnl_lock during
hclge_reset_wait(). So this patch releases the lock for the duration
of hclge_reset_wait().
Fixes:
6d4fab39533f ("net: hns3: Reset net device with rtnl_lock")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Tue, 30 Oct 2018 13:50:51 +0000 (21:50 +0800)]
net: hns3: bugfix for handling mailbox while the command queue reinitialized
In a multi-core machine, the mailbox service and reset service
will be executed at the same time. The reset service will re-initialize
the command queue, before that, the mailbox handler can only get some
invalid messages.
The HCLGE_STATE_CMD_DISABLE flag means that the command queue is not
available and needs to be reinitialized. Therefore, when the mailbox
handler recognizes this flag, it should not process the command.
Fixes:
dde1a86e93ca ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Tue, 30 Oct 2018 13:50:50 +0000 (21:50 +0800)]
net: hns3: fix incorrect return value/type of some functions
There are some functions that, when they fail to send the command,
need to return the corresponding error value to its caller.
Fixes:
46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes:
681ec3999b3d ("net: hns3: fix for vlan table lost problem when resetting")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Tue, 30 Oct 2018 13:50:49 +0000 (21:50 +0800)]
net: hns3: bugfix for hclge_mdio_write and hclge_mdio_read
When there is a PHY, the driver needs to complete some operations through
MDIO during reset reinitialization, so HCLGE_STATE_CMD_DISABLE is more
suitable than HCLGE_STATE_RST_HANDLING to prevent the MDIO operation from
being sent during the hardware reset.
Fixes:
b50ae26c57cb ("net: hns3: never send command queue message to IMP when reset)
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Tue, 30 Oct 2018 13:50:48 +0000 (21:50 +0800)]
net: hns3: bugfix for is_valid_csq_clean_head()
The HEAD pointer of the hardware command queue maybe equal to the command
queue's next_to_use in the driver, so that does not belong to the invalid
HEAD pointer, since the hardware may not process the command in time,
causing the HEAD pointer to be too late to update. The variables' name
in this function is unreadable, so give them a more readable one.
Fixes:
3ff504908f95 ("net: hns3: fix a dead loop in hclge_cmd_csq_clean")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Tue, 30 Oct 2018 13:50:47 +0000 (21:50 +0800)]
net: hns3: remove unnecessary queue reset in the hns3_uninit_all_ring()
It is not necessary to reset the queue in the hns3_uninit_all_ring(),
since the queue is stopped in the down operation, and will be reset
in the up operation. And the judgment of the HCLGE_STATE_RST_HANDLING
flag in the hclge_reset_tqp() is not correct, because we need to reset
tqp during pf reset, otherwise it may cause queue not being reset to
working state problem.
Fixes:
76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Tue, 30 Oct 2018 13:50:46 +0000 (21:50 +0800)]
net: hns3: bugfix for the initialization of command queue's spin lock
The spin lock of the command queue only need to be initialized once
when the driver initializes the command queue. It is not necessary to
initialize the spin lock when resetting. At the same time, the
modification of the queue member should be performed after acquiring
the lock.
Fixes:
3efb960f056d ("net: hns3: Refactor the initialization of command queue")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Tue, 30 Oct 2018 13:50:45 +0000 (21:50 +0800)]
net: hns3: bugfix for reporting unknown vector0 interrupt repeatly problem
The current driver supports handling two vector0 interrupts, reset and
mailbox. When the hardware reports an interrupt of another type of
interrupt source, if the driver does not process the interrupt, but
enables the interrupt, the hardware will repeatedly report the unknown
interrupt.
Therefore, the driver enables the vector0 interrupt after clearing the
known type of interrupt source. Other conditions are not enabled.
Fixes:
cd8c5c269b1d ("net: hns3: Fix for hclge_reset running repeatly problem")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Tue, 30 Oct 2018 13:50:44 +0000 (21:50 +0800)]
net: hns3: bugfix for buffer not free problem during resetting
When hns3_get_ring_config()/hns3_queue_to_ring()/
hns3_get_vector_ring_chain() failed during resetting, the allocated
memory has not been freed before these three functions return. So
this patch adds error handler in these functions to fix it.
Fixes:
76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Tue, 30 Oct 2018 13:50:43 +0000 (21:50 +0800)]
net: hns3: add error handler for hns3_nic_init_vector_data()
When hns3_nic_init_vector_data() fails to map ring to vector,
it should cancel the netif_napi_add() that has been successfully
done and then exits.
Fixes:
76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 30 Oct 2018 07:57:25 +0000 (00:57 -0700)]
net/mlx5e: fix csum adjustments caused by RXFCS
As shown by Dmitris, we need to use csum_block_add() instead of csum_add()
when adding the FCS contribution to skb csum.
Before 4.18 (more exactly commit
88078d98d1bb "net: pskb_trim_rcsum()
and CHECKSUM_COMPLETE are friends"), the whole skb csum was thrown away,
so RXFCS changes were ignored.
Then before commit
d55bef5059dd ("net: fix pskb_trim_rcsum_slow() with
odd trim offset") both mlx5 and pskb_trim_rcsum_slow() bugs were canceling
each other.
Now we fixed pskb_trim_rcsum_slow() we need to fix mlx5.
Note that this patch also rewrites mlx5e_get_fcs() to :
- Use skb_header_pointer() instead of reinventing it.
- Use __get_unaligned_cpu32() to avoid possible non aligned accesses
as Dmitris pointed out.
Fixes:
902a545904c7 ("net/mlx5e: When RXFCS is set, add FCS data into checksum calculation")
Reported-by: Paweł Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eran Ben Elisha <eranbe@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Dimitris Michailidis <dmichail@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Paweł Staszewski <pstaszewski@itcare.pl>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Tested-By: Maria Pasechnik <mariap@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Tue, 30 Oct 2018 06:10:49 +0000 (14:10 +0800)]
vhost: Fix Spectre V1 vulnerability
The idx in vhost_vring_ioctl() was controlled by userspace, hence a
potential exploitation of the Spectre variant 1 vulnerability.
Fixing this by sanitizing idx before using it to index d->vqs.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bo YU [Tue, 30 Oct 2018 03:42:10 +0000 (23:42 -0400)]
net: drop a space before tabs
Fix a warning from checkpatch.pl:'please no space before tabs'
in include/net/af_unix.h
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bo YU [Tue, 30 Oct 2018 03:42:09 +0000 (23:42 -0400)]
net: add an identifier name for 'struct sock *'
Fix a warning from checkpatch:
function definition argument 'struct sock *' should also have an
identifier name in include/net/af_unix.h.
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Mon, 29 Oct 2018 22:46:11 +0000 (22:46 +0000)]
net: hns3: fix spelling mistake "intrerrupt" -> "interrupt"
Trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Radoslaw Tyl [Mon, 22 Oct 2018 06:44:31 +0000 (08:44 +0200)]
ixgbe: fix MAC anti-spoofing filter after VFLR
This change resolves a driver bug where the driver is logging a
message that says "Spoofed packets detected". This can occur on the PF
(host) when a VF has VLAN+MACVLAN enabled and is re-started with a
different MAC address.
MAC and VLAN anti-spoofing filters are to be enabled together.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Fri, 19 Oct 2018 21:11:03 +0000 (14:11 -0700)]
i40e: Update status codes
Add a few new status code which will be used by the ice driver, and
rename a few to make them more consistent. Error code are mapped to
similar values as in i40e_status.h, so as to be compatible with older
VF drivers not using this status enum.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher [Thu, 18 Oct 2018 22:39:43 +0000 (15:39 -0700)]
ixgbe/ixgbevf: fix XFRM_ALGO dependency
Based on the original work from Arnd Bergmann.
When XFRM_ALGO is not enabled, the new ixgbe IPsec code produces a
link error:
drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.o: In function `ixgbe_ipsec_vf_add_sa':
ixgbe_ipsec.c:(.text+0x1266): undefined reference to `xfrm_aead_get_byname'
Simply selecting XFRM_ALGO from here causes circular dependencies, so
to fix it, we probably want this slightly more complex solution that is
similar to what other drivers with XFRM offload do:
A separate Kconfig symbol now controls whether we include the IPsec
offload code. To keep the old behavior, this is left as 'default y'. The
dependency in XFRM_OFFLOAD still causes a circular dependency but is
not actually needed because this symbol is not user visible, so removing
that dependency on top makes it all work.
CC: Arnd Bergmann <arnd@arndb.de>
CC: Shannon Nelson <shannon.nelson@oracle.com>
Fixes:
eda0333ac293 ("ixgbe: add VF IPsec management")
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Jacob Keller [Mon, 15 Oct 2018 19:21:28 +0000 (12:21 -0700)]
fm10k: bump driver version to match out-of-tree release
The upstream and out-of-tree drivers are once again at comparable
functionality. It's been a while since we updated the upstream driver
version, so bump it now.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Mon, 15 Oct 2018 19:18:29 +0000 (12:18 -0700)]
fm10k: add missing device IDs to the upstream driver
The device IDs for the Ethernet SDI Adapter devices were never added to
the upstream driver. The IDs are already in the pci.ids database, and
are supported by the out-of-tree driver.
Add the device IDs now, so that the upstream driver can recognize and
load these devices.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Mon, 15 Oct 2018 19:18:28 +0000 (12:18 -0700)]
fm10k: ensure completer aborts are marked as non-fatal after a resume
VF drivers can trigger PCIe completer aborts any time they read a queue
that they don't own. Even in nominal circumstances, it is not possible
to prevent the VF driver from reading queues it doesn't own. VF drivers
may attempt to read queues it previously owned, but which it no longer
does due to a PF reset.
Normally these completer aborts aren't an issue. However, on some
platforms these trigger machine check errors. This is true even if we
lower their severity from fatal to non-fatal. Indeed, we already have
code for lowering the severity.
We could attempt to mask these errors conditionally around resets, which
is the most common time they would occur. However this would essentially
be a race between the PF and VF drivers, and we may still occasionally
see machine check exceptions on these strictly configured platforms.
Instead, mask the errors entirely any time we resume VFs. By doing so,
we prevent the completer aborts from being sent to the parent PCIe
device, and thus these strict platforms will not upgrade them into
machine check errors.
Additionally, we don't lose any information by masking these errors,
because we'll still report VFs which attempt to access queues via the
FUM_BAD_VF_QACCESS errors.
Without this change, on platforms where completer aborts cause machine
check exceptions, the VF reading queues it doesn't own could crash the
host system. Masking the completer abort prevents this, so we should
mask it for good, and not just around a PCIe reset. Otherwise malicious
or misconfigured VFs could cause the host system to crash.
Because we are masking the error entirely, there is little reason to
also keep setting the severity bit, so that code is also removed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ngai-Mint Kwan [Mon, 15 Oct 2018 19:18:27 +0000 (12:18 -0700)]
fm10k: fix SM mailbox full condition
Current condition will always incorrectly report a full SM mailbox if an
IES API application is not running. Due to this, the
"fm10k_service_task" will be infinitely queued into the driver's
workqueue. This, in turn, will cause a "kworker" thread to report 100%
CPU utilization and might cause "soft lockup" events or system crashes.
To fix this issue, a new condition is added to determine if the SM
mailbox is in the correct state of FM10K_STATE_OPEN before proceeding.
In other words, an instance of the IES API must be running. If there is,
the remainder of the flow stays the same which is to determine if the SM
mailbox capacity has been exceeded or not and take appropriate action.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Miroslav Lichvar [Fri, 12 Oct 2018 11:13:39 +0000 (13:13 +0200)]
igb: shorten maximum PHC timecounter update interval
The timecounter needs to be updated at least once per ~550 seconds in
order to avoid a 40-bit SYSTIM timestamp to be misinterpreted as an old
timestamp.
Since commit
500462a9d ("timers: Switch to a non-cascading wheel"),
scheduling of delayed work seems to be less accurate and a requested
delay of 540 seconds may actually be longer than 550 seconds. Shorten
the delay to 480 seconds to be sure the timecounter is updated in time.
This fixes an issue with HW timestamps on 82580/I350/I354 being off by
~1100 seconds for few seconds every ~9 minutes.
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Fastabend [Mon, 29 Oct 2018 19:31:28 +0000 (12:31 -0700)]
bpf: tcp_bpf_recvmsg should return EAGAIN when nonblocking and no data
We return 0 in the case of a nonblocking socket that has no data
available. However, this is incorrect and may confuse applications.
After this patch we do the correct thing and return the error
EAGAIN.
Quoting return codes from recvmsg manpage,
EAGAIN or EWOULDBLOCK
The socket is marked nonblocking and the receive operation would
block, or a receive timeout had been set and the timeout expired
before data was received.
Fixes:
604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Yonghong Song [Mon, 29 Oct 2018 21:56:48 +0000 (14:56 -0700)]
tools/bpf: add unlimited rlimit for flow_dissector_load
On our test machine, bpf selftest test_flow_dissector.sh failed
with the following error:
# ./test_flow_dissector.sh
bpffs not mounted. Mounting...
libbpf: failed to create map (name: 'jmp_table'): Operation not permitted
libbpf: failed to load object 'bpf_flow.o'
./flow_dissector_load: bpf_prog_load bpf_flow.o
selftests: test_flow_dissector [FAILED]
Let us increase the rlimit to remove the above map
creation failure.
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Marc Zyngier [Tue, 30 Oct 2018 15:41:00 +0000 (15:41 +0000)]
net: mvpp2: Fix affinity hint allocation
The mvpp2 driver has the curious behaviour of passing a stack variable
to irq_set_affinity_hint(), which results in the kernel exploding
the first time anyone accesses this information. News flash: userspace
does, and irqbalance will happily take the machine down. Great stuff.
An easy fix is to track the mask within the queue_vector structure,
and to make sure it has the same lifetime as the interrupt itself.
Fixes:
e531f76757eb ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 30 Oct 2018 07:18:12 +0000 (00:18 -0700)]
net/mlx4_en: add a missing <net/ip.h> include
Abdul Haleem reported a build error on ppc :
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: `struct
iphdr` declared inside parameter list [enabled by default]
struct iphdr *iph)
^
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: its scope is
only this definition or declaration, which is probably not what you want
[enabled by default]
drivers/net/ethernet/mellanox/mlx4/en_rx.c: In function
get_fixed_ipv4_csum:
drivers/net/ethernet/mellanox/mlx4/en_rx.c:586:20: error: dereferencing
pointer to incomplete type
__u8 ipproto = iph->protocol;
^
Fixes:
55469bc6b577 ("drivers: net: remove <net/busy_poll.h> inclusion when not needed")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 29 Oct 2018 20:36:43 +0000 (20:36 +0000)]
rtnetlink: Disallow FDB configuration for non-Ethernet device
When an FDB entry is configured, the address is validated to have the
length of an Ethernet address, but the device for which the address is
configured can be of any type.
The above can result in the use of uninitialized memory when the address
is later compared against existing addresses since 'dev->addr_len' is
used and it may be greater than ETH_ALEN, as with ip6tnl devices.
Fix this by making sure that FDB entries are only configured for
Ethernet devices.
BUG: KMSAN: uninit-value in memcmp+0x11d/0x180 lib/string.c:863
CPU: 1 PID: 4318 Comm: syz-executor998 Not tainted 4.19.0-rc3+ #49
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x14b/0x190 lib/dump_stack.c:113
kmsan_report+0x183/0x2b0 mm/kmsan/kmsan.c:956
__msan_warning+0x70/0xc0 mm/kmsan/kmsan_instr.c:645
memcmp+0x11d/0x180 lib/string.c:863
dev_uc_add_excl+0x165/0x7b0 net/core/dev_addr_lists.c:464
ndo_dflt_fdb_add net/core/rtnetlink.c:3463 [inline]
rtnl_fdb_add+0x1081/0x1270 net/core/rtnetlink.c:3558
rtnetlink_rcv_msg+0xa0b/0x1530 net/core/rtnetlink.c:4715
netlink_rcv_skb+0x36e/0x5f0 net/netlink/af_netlink.c:2454
rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:4733
netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
netlink_unicast+0x1638/0x1720 net/netlink/af_netlink.c:1343
netlink_sendmsg+0x1205/0x1290 net/netlink/af_netlink.c:1908
sock_sendmsg_nosec net/socket.c:621 [inline]
sock_sendmsg net/socket.c:631 [inline]
___sys_sendmsg+0xe70/0x1290 net/socket.c:2114
__sys_sendmsg net/socket.c:2152 [inline]
__do_sys_sendmsg net/socket.c:2161 [inline]
__se_sys_sendmsg+0x2a3/0x3d0 net/socket.c:2159
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2159
do_syscall_64+0xb8/0x100 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x63/0xe7
RIP: 0033:0x440ee9
Code: e8 cc ab 02 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7
48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff
ff 0f 83 bb 0a fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007fff6a93b518 EFLAGS:
00000213 ORIG_RAX:
000000000000002e
RAX:
ffffffffffffffda RBX:
0000000000000000 RCX:
0000000000440ee9
RDX:
0000000000000000 RSI:
0000000020000240 RDI:
0000000000000003
RBP:
0000000000000000 R08:
00000000004002c8 R09:
00000000004002c8
R10:
00000000004002c8 R11:
0000000000000213 R12:
000000000000b4b0
R13:
0000000000401ec0 R14:
0000000000000000 R15:
0000000000000000
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:256 [inline]
kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:181
kmsan_kmalloc+0x98/0x100 mm/kmsan/kmsan_hooks.c:91
kmsan_slab_alloc+0x10/0x20 mm/kmsan/kmsan_hooks.c:100
slab_post_alloc_hook mm/slab.h:446 [inline]
slab_alloc_node mm/slub.c:2718 [inline]
__kmalloc_node_track_caller+0x9e7/0x1160 mm/slub.c:4351
__kmalloc_reserve net/core/skbuff.c:138 [inline]
__alloc_skb+0x2f5/0x9e0 net/core/skbuff.c:206
alloc_skb include/linux/skbuff.h:996 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1189 [inline]
netlink_sendmsg+0xb49/0x1290 net/netlink/af_netlink.c:1883
sock_sendmsg_nosec net/socket.c:621 [inline]
sock_sendmsg net/socket.c:631 [inline]
___sys_sendmsg+0xe70/0x1290 net/socket.c:2114
__sys_sendmsg net/socket.c:2152 [inline]
__do_sys_sendmsg net/socket.c:2161 [inline]
__se_sys_sendmsg+0x2a3/0x3d0 net/socket.c:2159
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2159
do_syscall_64+0xb8/0x100 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x63/0xe7
v2:
* Make error message more specific (David)
Fixes:
090096bf3db1 ("net: generic fdb support for drivers without ndo_fdb_<op>")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-and-tested-by: syzbot+3a288d5f5530b901310e@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+d53ab4e92a1db04110ff@syzkaller.appspotmail.com
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 29 Oct 2018 15:13:11 +0000 (23:13 +0800)]
sctp: check policy more carefully when getting pr status
When getting pr_assocstatus and pr_streamstatus by sctp_getsockopt,
it doesn't correctly process the case when policy is set with
SCTP_PR_SCTP_ALL | SCTP_PR_SCTP_MASK. It even causes a
slab-out-of-bounds in sctp_getsockopt_pr_streamstatus().
This patch fixes it by return -EINVAL for this case.
Fixes:
0ac1077e3a54 ("sctp: get pr_assoc and pr_stream all status with SCTP_PR_SCTP_ALL")
Reported-by: syzbot+5da0d0a72a9e7d791748@syzkaller.appspotmail.com
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 29 Oct 2018 15:10:29 +0000 (23:10 +0800)]
sctp: clear the transport of some out_chunk_list chunks in sctp_assoc_rm_peer
If a transport is removed by asconf but there still are some chunks with
this transport queuing on out_chunk_list, later an use-after-free issue
will be caused when accessing this transport from these chunks in
sctp_outq_flush().
This is an old bug, we fix it by clearing the transport of these chunks
in out_chunk_list when removing a transport in sctp_assoc_rm_peer().
Reported-by: syzbot+56a40ceee5fb35932f4d@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 30 Oct 2018 03:48:00 +0000 (20:48 -0700)]
Merge branch 'mlxsw-Couple-of-fixes'
Ido Schimmel says:
====================
mlxsw: Couple of fixes
First patch makes sure mlxsw does not ignore user requests to delete FDB
entries that were learned by the device.
Second patch fixes a use-after-free that can be triggered by requesting
a reload via devlink when the previous reload failed.
Please consider both patches for stable. They apply cleanly to both
4.18.y and 4.19.y.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shalom Toledo [Mon, 29 Oct 2018 14:26:16 +0000 (14:26 +0000)]
mlxsw: core: Fix devlink unregister flow
After a failed reload, the driver is still registered to devlink, its
devlink instance is still allocated and the 'reload_fail' flag is set.
Then, in the next reload try, the driver's allocated devlink instance will
be freed without unregistering from devlink and its components (e.g,
resources). This scenario can cause a use-after-free if the user tries to
execute command via devlink user-space tool.
Fix by not freeing the devlink instance during reload (failed or not).
Fixes:
24cc68ad6c46 ("mlxsw: core: Add support for reload")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 29 Oct 2018 14:26:14 +0000 (14:26 +0000)]
mlxsw: spectrum_switchdev: Don't ignore deletions of learned MACs
Demands to remove FDB entries should be honored even if the FDB entry in
question was originally learned, and not added by the user. Therefore
ignore the added_by_user datum for SWITCHDEV_FDB_DEL_TO_DEVICE.
Fixes:
816a3bed9549 ("switchdev: Add fdb.added_by_user to switchdev notifications")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Suggested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Chancellor [Mon, 29 Oct 2018 10:51:58 +0000 (03:51 -0700)]
hinic: Fix l4_type parameter in hinic_task_set_tunnel_l4
Clang warns:
drivers/net/ethernet/huawei/hinic/hinic_tx.c:392:34: error: implicit
conversion from enumeration type 'enum hinic_l4_tunnel_type' to
different enumeration type 'enum hinic_l4_offload_type'
[-Werror,-Wenum-conversion]
hinic_task_set_tunnel_l4(task, TUNNEL_UDP_NO_CSUM,
~~~~~~~~~~~~~~~~~~~~~~~~ ^~~~~~~~~~~~~~~~~~
1 error generated.
It seems that hinic_task_set_tunnel_l4 was meant to take an enum of type
hinic_l4_tunnel_type, not hinic_l4_offload_type, given both the name of
the functions and the values used.
Fixes:
cc18a7543d2f ("net-next/hinic: add checksum offload and TSO support")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Colitti [Mon, 29 Oct 2018 00:30:29 +0000 (09:30 +0900)]
Documentation: ip-sysctl.txt: Document tcp_fwmark_accept
This patch documents the tcp_fwmark_accept sysctl that was
added in 3.15.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Jungel [Sun, 28 Oct 2018 11:54:10 +0000 (12:54 +0100)]
bonding: fix length of actor system
The attribute IFLA_BOND_AD_ACTOR_SYSTEM is sent to user space having the
length of sizeof(bond->params.ad_actor_system) which is 8 byte. This
patch aligns the length to ETH_ALEN to have the same MAC address exposed
as using sysfs.
Fixes:
f87fda00b6ed2 ("bonding: prevent out of bound accesses")
Signed-off-by: Tobias Jungel <tobias.jungel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Fri, 26 Oct 2018 03:30:35 +0000 (11:30 +0800)]
ipv4/igmp: fix v1/v2 switchback timeout based on rfc3376, 8.12
Similiar with ipv6 mcast commit
89225d1ce6af3 ("net: ipv6: mld: fix v1/v2
switchback timeout to rfc3810, 9.12.")
i) RFC3376 8.12. Older Version Querier Present Timeout says:
The Older Version Querier Interval is the time-out for transitioning
a host back to IGMPv3 mode once an older version query is heard.
When an older version query is received, hosts set their Older
Version Querier Present Timer to Older Version Querier Interval.
This value MUST be ((the Robustness Variable) times (the Query
Interval in the last Query received)) plus (one Query Response
Interval).
Currently we only use a hardcode value IGMP_V1/v2_ROUTER_PRESENT_TIMEOUT.
Fix it by adding two new items mr_qi(Query Interval) and mr_qri(Query Response
Interval) in struct in_device.
Now we can calculate the switchback time via (mr_qrv * mr_qi) + mr_qri.
We need update these values when receive IGMPv3 queries.
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 29 Oct 2018 22:37:33 +0000 (15:37 -0700)]
Merge tag 'armsoc-soc' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"A couple of platforms change hands in the MAINTAINERS file:
- Linus Walleij lists himself for the ARM Reference platforms:
versatile, vexpress, integrator and realview. He has been the main
contributor for these for a while, and makes it official now.
- Vladimir Zapolskiy takes over the LPC18xx platform from Joachim
Eastwood
- Manivannan Sadhasivam becomes a secondary maintainer for the
Actions Semi machines
- Nicolas Ferre lists updates the MAINTAINER listing for the AT91
platform: Ludovic Desroches is now a co-maintainer for the
platform, and several other people (Claudiu Beznea, Cristian
Birsan, Eugen Hristev, Codrin Ciubotariu) take over individual
device drivers.
Thanks everyone for working on this, and welcome to the new
maintainers!
The "virt" platform on qemy or kvm can now be used in big-endian mode
without additional tricks, thanks to Jason Donenfeld.
Once again, we gain support for another NXP i.MX6 variant, this time
it's the i.MX 6ULZ 32-bit single-core version.
On arm64, we add support for two SoCs from Renesas: RZ/G2E (r8a774c0)
and RZ/G2M (r8a774a1). These are described as microcontrollers on the
manufacturer website, but appear to be rather powerful. The RZ/G2M is
used on the reference board for the CIP Super Long Term Support (SLTS)
Linux Kernels"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
MAINTAINERS: Assign myself as a maintainer of ARM/LPC18XX architecture
arm64: exynos: Enable generic power domain support
MAINTAINERS: remove non-exsiting email address of Baoyou
MAINTAINERS: fix pattern in ARM/Synaptics berlin SoC section
MAINTAINERS: Drop dt-bindings/genpd/k2g.h
ARM: samsung: Limit SAMSUNG_PM_CHECK config option to non-Exynos platforms
arm64: actions: Enable PINCTRL in platforms Kconfig
MAINTAINERS: Add entry for Actions Semi Owl SoCs DMA driver
MAINTAINERS: Add entry for Actions Semiconductor Owl I2C driver
MAINTAINERS: Update clock binding entry for Actions Semi Owl SoCs
ARM: imx: add i.mx6ulz msl support
ARM: Assume maintainership of ARM reference designs
ARM: support big-endian for the virt architecture
MAINTAINERS: sdhci: move the Microchip entry to proper location
MAINTAINERS: move former ATMEL entries to proper MICROCHIP location
MAINTAINERS: remove the / ATMEL string from MICROCHIP entries
MAINTAINERS: iio: add co-maintainer to SAMA5D2-compatible ADC driver
MAINTAINERS: pwm: add entry for Microchip pwm driver
MAINTAINERS: dmaengine: add files to Microchip dma entry
MAINTAINERS: USB: change maintainer for Microchip USBA gadget driver
...
Linus Torvalds [Mon, 29 Oct 2018 22:16:01 +0000 (15:16 -0700)]
Merge tag 'armsoc-drivers' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl"
interface that was a little controversial at first, but the version
we merged solved that by not exposing arbitrary firmware calls to
user space.
- The Amlogic Meson platform gains a "canvas" driver that is used for
video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for their
respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in
particular a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem" device
driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (129 commits)
firmware: tegra: bpmp: Implement suspend/resume support
drivers: clk: Add ZynqMP clock driver
dt-bindings: clock: Add bindings for ZynqMP clock driver
firmware: xilinx: Add zynqmp IOCTL API for device control
Documentation: xilinx: Add documentation for eemi APIs
MAINTAINERS: imx: include drivers/firmware/imx path
firmware: imx: add misc svc support
firmware: imx: add SCU firmware driver support
reset: Fix potential use-after-free in __of_reset_control_get()
dt-bindings: arm: fsl: add scu binding doc
soc: fsl: qbman: add interrupt coalesce changing APIs
soc: fsl: bman_portals: defer probe after bman's probe
soc: fsl: qbman: Use last response to determine valid bit
soc: fsl: qbman: Add 64 bit DMA addressing requirement to QBMan
soc: fsl: qbman: replace CPU 0 with any online CPU in hotplug handlers
soc: fsl: qbman: Check if CPU is offline when initializing portals
reset: qcom: PDC Global (Power Domain Controller) reset controller
dt-bindings: reset: Add PDC Global binding for SDM845 SoCs
reset: Grammar s/more then once/more than once/
bus: ti-sysc: Just use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
...
Linus Torvalds [Mon, 29 Oct 2018 22:10:45 +0000 (15:10 -0700)]
Merge tag 'armsoc-defconfig' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"The defconfig changes are split out from the rest again. This time we
have a number of changes for NXP i.MX and Renesas, including a cleanup
of old options.
Some smaller changes are for Socionext Uniphier, Allwinner, Qualcomm,
Rockchip, Renesas, AT91, Hisilicon, and STM32. All of these just
enable platform specific device drivers"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
arm64: defconfig: Enable SERIAL_8250_OMAP
arm64: defconfig: Enable TI_SCI related configs
ARM: imx_v6_v7_defconfig: Select CONFIG_TMPFS_POSIX_ACL
ARM: imx_v4_v5_defconfig: Remove unneeded options
ARM: imx_v4_v5_defconfig: Re-sync defconfig
ARM: mxs_defconfig: Remove unneeded options
ARM: mxs_defconfig: Re-sync defconfig
ARM: imx_v6_v7_defconfig: Remove unneeded options
ARM: imx_v6_v7_defconfig: Re-sync defconfig
ARM: imx_v6_v7_defconfig: select CONFIG_ARM_CPUIDLE by default
ARM: imx_v6_v7_defconfig: Make usbnet drivers builtin for boot
ARM: imx_v6_v7_defconfig: add CONFIG_FW_LOADER_USER_HELPER
ARM: imx_v6_v7_defconfig: Select CONFIG_SENSORS_MC13783_ADC
ARM: multi_v7_defconfig: enable CONFIG_MMC_UNIPHIER
arm64: defconfig: enable CONFIG_MMC_UNIPHIER
ARM: multi_v7_defconfig: Enable USB phys for UniPhier SoCs
arm64: defconfig: Enable USB phys for UniPhier SoCs
arm64: defconfig: enable Rockchip Innosilicon hdmiphy
arm64: defconfig: Enable PCIEPORTBUS
arm64: defconfig: enable HiSilicon HNS3 driver
...
Linus Torvalds [Mon, 29 Oct 2018 22:05:20 +0000 (15:05 -0700)]
Merge tag 'armsoc-dt' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"There are close to 800 indivudal changesets in this branch again,
which feels like a lot. There are particularly many changes for the
NVIDIA Tegra platform this time, in fact more than it has seen in the
two years since the v4.9 merge window. Aside from this, it's been
fairly normal, with lots of changes going into Renesas R-CAR, NXP
i.MX, Allwinner Sunxi, Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5 is a
minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core Marvell Armada 8040
network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in the
BMC.
NXP i.MX usually sees a lot of new boards each release. This time
there we only add one minor variant: ConnectCore 6UL SBC Pro uses the
same SoM design as the ConnectCore 6UL SBC Express added later.
However, there is a new chip, the i.MX6ULZ, which is an even smaller
variant of the i.MX6ULL, with features removed. There is also support
for the reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute
module based on bcm2837, it was launched in early 2017 but only now
added to the kernel, both as 32-bit and as 64-bit files, as we tend to
do for Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time are:
- Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
- Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
- Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
- Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana Pi
M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit Asus
Tinker board, the model 'S' based on rk3288, and three now boards
based on the popular RK3399 chip:
- ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
- Rock960: https://www.96boards.org/product/rock960/
- RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and the
RK3399 is the same chip used in several Chromebooks. Finally, we get
support for the PX30 (aka rk3326) chip, which is based on the low-end
64-bit Cortex-A35 CPU core. So far, only the evaluation board is
supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is
based on the MT7622 WiFi router platform, and the first product I've
seen with a 64-bit Mediatek chip in that market:
http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2), another
quad-core Cortex-A53 SoC, and its evaluation platform. On the 32-bit
side, we gain support for an actual end-user product, the Endless
Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform.
This chip is commonly known as the Snapdragon 835, and is used in
high-end phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the
previously added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the
M3NULCB Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing
files, the only board that gets added is the Toradex Colibri T20 on
Colibri Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the
(formerly Marvell) Berlin line of set-top-box chips used e.g. in the
various Google Chromecast. Only the .dtsi gets added at this point, no
actual machines"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (721 commits)
ARM: dts: socfgpa: remove ethernet aliases from dtsi
arm64: dts: stratix10: add ethernet aliases
dt-bindings: mediatek: Add bindig for MT7623 IOMMU and SMI
dt-bindings: mediatek: Add JPEG Decoder binding for MT7623
dt-bindings: iommu: mediatek: Add binding for MT7623
dt-bindings: clock: mediatek: add support for MT7623
ARM: dts: mvebu: armada-385-db-
88f6820-amc: auto-detect nand ECC properites
ARM: dts: da850-lego-ev3: slow down A/DC as much as possible
ARM: dts: da850-evm: Enable tca6416 on baseboard
arm64: dts: uniphier: Add USB2 PHY nodes
arm64: dts: uniphier: Add USB3 controller nodes
ARM: dts: uniphier: Add USB2 PHY nodes
ARM: dts: uniphier: Add USB3 controller nodes
arm64: dts: meson-axg: s400: disable emmc
arm64: dts: meson-axg: s400: add missing emmc pwrseq
arm64: dts: clearfog-gt-8k: add PCIe slot description
ARM: dts: at91: sama5d4_xplained: even nand memory partitions
ARM: dts: at91: sama5d3_xplained: even nand memory partitions
ARM: dts: at91: at91sam9x5cm: even nand memory partitions
ARM: dts: at91: sama5d2_ptc_ek: fix bootloader env offsets
...
Linus Torvalds [Mon, 29 Oct 2018 22:02:40 +0000 (15:02 -0700)]
Merge branch 'parisc-4.20-2' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"Three small patches:
- A boot fix for A500 machines, crash was caused by the new
alternative patching code from this merge window (Dave)
- Change __kernel_suseconds_t to match glibc on 64-bit parisc (Arnd)
- Use constants instead of hard-coded numbers (me)"
* 'parisc-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix A500 boot crash
parisc: Use LINUX_GATEWAY_SPACE constant in entry.S
parisc64: change __kernel_suseconds_t to match glibc
Linus Torvalds [Mon, 29 Oct 2018 21:44:03 +0000 (14:44 -0700)]
Merge branch 'i2c/for-4.20' of git://git./linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has not so much stuff this time. Mostly driver enablement for new
SoCs, some driver bugfixes, and some cleanups"
* 'i2c/for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (35 commits)
MAINTAINERS: add maintainer for Renesas RIIC driver
i2c: sh_mobile: Remove dummy runtime PM callbacks
i2c: uniphier-f: fix race condition when IRQ is cleared
i2c: uniphier-f: fix occasional timeout error
i2c: uniphier-f: make driver robust against concurrency
i2c: i2c-qcom-geni: Simplify irq handler
i2c: i2c-qcom-geni: Simplify tx/rx functions
i2c: designware: Set IRQF_NO_SUSPEND flag for all BYT and CHT controllers
i2c: mux: mlxcpld: simplify code to reach the adapter
i2c: mux: ltc4306: simplify code to reach the adapter
i2c: mux: pca954x: simplify code to reach the adapter
i2c: core: remove level of indentation in i2c_transfer
i2c: core: remove outdated DEBUG output
i2c: zx2967: use core to detect 'no zero length' quirk
i2c: tegra: use core to detect 'no zero length' quirk
i2c: qup: use core to detect 'no zero length' quirk
i2c: omap: use core to detect 'no zero length' quirk
i2c: Convert to using %pOFn instead of device_node.name
i2c: brcmstb: Allow enabling the driver on DSL SoCs
eeprom: at24: fix unexpected timeout under high load
...
Linus Torvalds [Mon, 29 Oct 2018 21:29:58 +0000 (14:29 -0700)]
Merge tag 'media/v4.20-1' of git://git./linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new dvb frontend driver: lnbh29
- new sensor drivers: imx319 and imx 355
- some old soc_camera driver renames to avoid conflict with new
drivers
- new i.MX Pixel Pipeline (PXP) mem-to-mem platform driver
- a new V4L2 frontend for the FWHT codec
- several other improvements, bug fixes, code cleanups, etc
* tag 'media/v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (289 commits)
media: rename soc_camera I2C drivers
media: cec: forgot to cancel delayed work
media: vivid: Support 480p for webcam capture
media: v4l2-tpg: fix kernel oops when enabling HFLIP and OSD
media: vivid: Add 16-bit bayer to format list
media: v4l2-tpg-core: Add 16-bit bayer
media: pvrusb2: replace `printk` with `pr_*`
media: venus: vdec: fix decoded data size
media: cx231xx: fix potential sign-extension overflow on large shift
media: dt-bindings: media: rcar_vin: add device tree support for r8a7744
media: isif: fix a NULL pointer dereference bug
media: exynos4-is: make const array config_ids static
media: cx23885: make const array addr_list static
media: ivtv: make const array addr_list static
media: bttv-input: make const array addr_list static
media: cx18: Don't check for address of video_dev
media: dw9807-vcm: Fix probe error handling
media: dw9714: Remove useless error message
media: dw9714: Fix error handling in probe function
media: cec: name for RC passthrough device does not need 'RC for'
...
Chris Brandt [Fri, 26 Oct 2018 19:57:10 +0000 (14:57 -0500)]
MAINTAINERS: add maintainer for Renesas RIIC driver
The RIIC I2C controller is used in Renesas RZ/A SoCs.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
[wsa: added documentation file]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jarkko Nikula [Wed, 24 Oct 2018 13:51:32 +0000 (16:51 +0300)]
i2c: sh_mobile: Remove dummy runtime PM callbacks
Platform drivers don't need dummy runtime PM callbacks that just return
success and non-NULL pm pointer in their struct device_driver in order
to have runtime PM happening. This has changed since following commits:
05aa55dddb9e ("PM / Runtime: Lenient generic runtime pm callbacks")
543f2503a956 ("PM / platform_bus: Allow runtime PM by default")
8b313a38ecff ("PM / Platform: Use generic runtime PM callbacks directly")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Masahiro Yamada [Tue, 16 Oct 2018 03:01:49 +0000 (12:01 +0900)]
i2c: uniphier-f: fix race condition when IRQ is cleared
The current IRQ handler clears all the IRQ status bits when it bails
out. This is dangerous because it might clear away the status bits
that have just been set while processing the current handler. If this
happens, the IRQ event for the latest transfer is lost forever.
The IRQ status bits must be cleared *before* the next transfer is
kicked.
Fixes:
6a62974b667f ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Masahiro Yamada [Tue, 16 Oct 2018 03:01:48 +0000 (12:01 +0900)]
i2c: uniphier-f: fix occasional timeout error
Currently, a timeout error could happen at a repeated START condition.
For a (non-repeated) START condition, the controller starts sending
data when the UNIPHIER_FI2C_CR_STA bit is set. However, for a repeated
START condition, the hardware starts running when the slave address is
written to the TX FIFO - the write to the UNIPHIER_FI2C_CR register is
actually unneeded.
Because the hardware is already running before the IRQ is enabled for
a repeated START, the driver may miss the IRQ event. In most cases,
this problem does not show up since modern CPUs are much faster than
the I2C transfer. However, it is still possible that a context switch
happens after the controller starts, but before the IRQ register is
set up.
To fix this,
- Do not write UNIPHIER_FI2C_CR for repeated START conditions.
- Enable IRQ *before* writing the slave address to the TX FIFO.
- Disable IRQ for the current CPU while queuing up the TX FIFO;
If the CPU is interrupted by some task, the interrupt handler
might be invoked due to the empty TX FIFO before completing the
setup.
Fixes:
6a62974b667f ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Masahiro Yamada [Tue, 16 Oct 2018 03:01:47 +0000 (12:01 +0900)]
i2c: uniphier-f: make driver robust against concurrency
This is unlikely to happen, but it is possible for a CPU to enter
the interrupt handler just after wait_for_completion_timeout() has
expired. If this happens, the hardware is accessed from multiple
contexts concurrently.
Disable the IRQ after wait_for_completion_timeout(), and do nothing
from the handler when the IRQ is disabled.
Fixes:
6a62974b667f ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Mon, 29 Oct 2018 18:52:46 +0000 (18:52 +0000)]
Merge branch 'i2c-mux/for-next' of https://github.com/peda-r/i2c-mux into i2c/for-4.20-fixed
Linus Torvalds [Mon, 29 Oct 2018 18:25:24 +0000 (11:25 -0700)]
HID: input: simplify/fix high-res scroll event handling
Commit
1ff2e1a44e02 ("HID: input: Create a utility class for counting
scroll events") created the helper function
hid_scroll_counter_handle_scroll()
to handle high-res scroll events and also expose them as regular wheel
events.
But the resulting algorithm was unstable, and causes scrolling to be
very unreliable. When you hit the half-way mark of the highres
multiplier, small highres movements will incorrectly translate into big
traditional wheel movements, causing odd jitters.
Simplify the code and make the output stable.
NOTE! I'm pretty sure this will need further tweaking. But this at
least turns a unusable mouse wheel on my Logitech MX Anywhere 2S into
a usable one.
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Harry Cutts <hcutts@chromium.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 29 Oct 2018 17:42:20 +0000 (10:42 -0700)]
Merge tag 'tty-4.20-rc1' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big tty and serial pull request for 4.20-rc1
Lots of little things here, including a merge from the SPI tree in
order to keep things simpler for everyone to sync around for one
platform.
Major stuff is:
- tty buffer clearing after use
- atmel_serial fixes and additions
- xilinx uart driver updates
and of course, lots of tiny fixes and additions to individual serial
drivers.
All of these have been in linux-next with no reported issues for a
while"
* tag 'tty-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (66 commits)
of: base: Change logic in of_alias_get_alias_list()
of: base: Fix english spelling in of_alias_get_alias_list()
serial: sh-sci: do not warn if DMA transfers are not supported
serial: uartps: Do not allow use aliases >= MAX_UART_INSTANCES
tty: check name length in tty_find_polling_driver()
serial: sh-sci: Add r8a77990 support
tty: wipe buffer if not echoing data
tty: wipe buffer.
serial: fsl_lpuart: Remove the alias node dependence
TTY: sn_console: Replace spin_is_locked() with spin_trylock()
Revert "serial:serial_core: Allow use of CTS for PPS line discipline"
serial: 8250_uniphier: add auto-flow-control support
serial: 8250_uniphier: flatten probe function
serial: 8250_uniphier: remove unused "fifo-size" property
dt-bindings: serial: sh-sci: Document r8a7744 bindings
serial: uartps: Fix missing unlock on error in cdns_get_id()
tty/serial: atmel: add ISO7816 support
tty/serial_core: add ISO7816 infrastructure
serial:serial_core: Allow use of CTS for PPS line discipline
serial: docs: Fix filename for serial reference implementation
...
Linus Torvalds [Mon, 29 Oct 2018 17:38:10 +0000 (10:38 -0700)]
Merge tag 'staging-4.20-rc1' of git://git./linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the big staging and IIO driver pull request for 4.20-rc1.
There are lots of things here, we ended up adding more lines than
removing, thanks to a large influx of Comedi National Instrument
device support. Someday soon we need to get comedi out of staging...
Other than the comedi drivers, the "big" things here are:
- new iio drivers
- delete dgnc driver (no one used it and no one had the hardware
anymore)
- vbox driver updates and fixes
- erofs fixes
- tons and tons of tiny checkpatch fixes for almost all staging
drivers
All of these have been in linux-next, with the last few happening a
bit "late" due to them getting stuck on my laptop during travel to the
Mantainers summit"
* tag 'staging-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (690 commits)
staging: gasket: Fix sparse "incorrect type in assignment" warnings.
staging: gasket: remove debug logs for callback invocation
staging: gasket: remove debug logs in page table mapping calls
staging: rtl8188eu: core: Use sizeof(*p) instead of sizeof(struct P) for memory allocation
staging: ks7010: Remove extra blank line
staging: gasket: Remove extra blank line
staging: media: davinci_vpfe: Fix spelling mistake in enum
staging: speakup: Add a pair of braces
staging: wlan-ng: Replace long int with long
staging: MAINTAINERS: remove obsolete IPX staging directory
staging: MAINTAINERS: remove NCP filesystem entry
staging: rtl8188eu: cleanup comparsions to false
staging: gasket: Update device virtual address comment
staging: gasket: sysfs: fix attribute release comment
staging: gasket: apex: fix sysfs_show
staging: gasket: page_table: simplify gasket_components_to_dev_address
staging: gasket: page_table: fix comment in components_to_dev_address
staging: gasket: page table: fixup error path allocating coherent mem
staging: gasket: page_table: rearrange gasket_page_table_entry
staging: gasket: page_table: remove unnecessary PTE status set to free
...
Linus Torvalds [Mon, 29 Oct 2018 17:30:44 +0000 (10:30 -0700)]
Merge tag 'mailbox-v4.20' of git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox updates from Jassi Brar:
- convert print users to use the %pOFn format specifier
- enable ti-msgmr driver for the K3 platform as well
- add QCS404 to compatible list of QCOM's APCS IPC driver
- minor spelling fixes toogle -> toggle
- kzalloc failure catch in Mediatek driver
* tag 'mailbox-v4.20' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: mediatek: Add check for possible failure of kzalloc
mailbox: bcm-flexrm-mailbox: fix spelling mistake "toogle" -> "toggle"
mailbox: qcom: Add QCS404 APPS Global compatible
drivers: mailbox: Make ti-msgmr driver depend on ARCH_K3
mailbox: Convert to using %pOFn instead of device_node.name
Linus Torvalds [Mon, 29 Oct 2018 17:23:36 +0000 (10:23 -0700)]
Merge tag 'filesystems_for_v4.20-rc1' of git://git./linux/kernel/git/jack/linux-fs
Pull ext2 and udf updates from Jan Kara:
"Small ext2 cleanups and a couple of udf fixes"
* tag 'filesystems_for_v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext2: remove redundant building macro check
udf: Drop pack pragma from udf_sb.h
udf: Drop freed bitmap / table support
udf: Fix crash during mount
udf: Prevent write-unsupported filesystem to be remounted read-write
ext2: cache NULL when both default_acl and acl are NULL
udf: remove unused variables group_start and nr_groups
Linus Torvalds [Mon, 29 Oct 2018 16:19:53 +0000 (09:19 -0700)]
Merge tag 'for_v4.20-rc1' of git://git./linux/kernel/git/jack/linux-fs
Pull fsnotify updates from Jan Kara:
"Amir's patches to implement superblock fanotify watches, Xiaoming's
patch to enable reporting of thread IDs in fanotify events instead of
TGIDs (sadly the patch got mis-attributed to Amir and I've noticed
only now), and a fix of possible oops on umount caused by fsnotify
infrastructure"
* tag 'for_v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fsnotify: Fix busy inodes during unmount
fs: group frequently accessed fields of struct super_block together
fanotify: support reporting thread id instead of process id
fanotify: add BUILD_BUG_ON() to count the bits of fanotify constants
fsnotify: convert runtime BUG_ON() to BUILD_BUG_ON()
fanotify: deprecate uapi FAN_ALL_* constants
fanotify: simplify handling of FAN_ONDIR
fsnotify: generalize handling of extra event flags
fanotify: fix collision of internal and uapi mark flags
fanotify: store fanotify_init() flags in group's fanotify_data
fanotify: add API to attach/detach super block mark
fsnotify: send path type events to group with super block marks
fsnotify: add super block object type
Linus Torvalds [Mon, 29 Oct 2018 16:09:47 +0000 (09:09 -0700)]
Merge tag '9p-for-4.20' of git://github.com/martinetd/linux
Pull 9p updates from Dominique Martinet:
"Highlights this time around are the end of Matthew's work to remove
the custom 9p request cache and use a slab directly for requests, with
some extra patches on my end to not degrade performance, but it's a
very good cleanup.
Tomas and I fixed a few more syzkaller bugs (refcount is the big one),
and I had a go at the coverity bugs and at some of the bugzilla
reports we had open for a while.
I'm a bit disappointed that I couldn't get much reviews for a few of
my own patches, but the big ones got some and it's all been soaking in
linux-next for quite a while so I think it should be OK.
Summary:
- Finish removing the custom 9p request cache mechanism
- Embed part of the fcall in the request to have better slab
performance (msize usually is power of two aligned)
- syzkaller fixes:
* add a refcount to 9p requests to avoid use after free
* a few double free issues
- A few coverity fixes
- Some old patches that were in the bugzilla:
* do not trust pdu content for size header
* mount option for lock retry interval"
* tag '9p-for-4.20' of git://github.com/martinetd/linux: (21 commits)
9p/trans_fd: put worker reqs on destroy
9p/trans_fd: abort p9_read_work if req status changed
9p: potential NULL dereference
9p locks: fix glock.client_id leak in do_lock
9p: p9dirent_read: check network-provided name length
9p/rdma: remove useless check in cm_event_handler
9p: acl: fix uninitialized iattr access
9p locks: add mount option for lock retry interval
9p: do not trust pdu content for stat item size
9p: Rename req to rreq in trans_fd
9p: fix spelling mistake in fall-through annotation
9p/rdma: do not disconnect on down_interruptible EAGAIN
9p: Add refcount to p9_req_t
9p: rename p9_free_req() function
9p: add a per-client fcall kmem_cache
9p: embed fcall in req to round down buffer allocs
9p: Remove p9_idpool
9p: Use a slab for allocating requests
9p: clear dangling pointers in p9stat_free
v9fs_dir_readdir: fix double-free on p9stat_read error
...
Linus Torvalds [Mon, 29 Oct 2018 16:04:26 +0000 (09:04 -0700)]
Merge branch 'for-next' of git://git./linux/kernel/git/gerg/m68knommu
Pull m68k nommu fix from Greg Ungerer:
"Only a single change to fix an out of bounds array access when parsing
boot command line"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: fix command-line parsing when passed from u-boot
Linus Torvalds [Mon, 29 Oct 2018 16:02:15 +0000 (09:02 -0700)]
Merge tag 'm68k-for-v4.20-tag1' of git://git./linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
"Just two small cleanups"
* tag 'm68k-for-v4.20-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/sun3: Remove is_medusa and m68k_pgtable_cachemode
m68k/atari: ARAnyM - Remove reference to long-deprecated MODULE_PARM
Linus Torvalds [Mon, 29 Oct 2018 15:25:00 +0000 (08:25 -0700)]
Merge tag 'csky-for-linus-4.20' of https://github.com/c-sky/csky-linux
Pull C-SKY architecture port from Guo Ren:
"This contains the Linux port for C-SKY(csky) based on linux-4.19
Release, which has been through 10 rounds of review on mailing list.
More information:
http://en.c-sky.com
The development repo:
https://github.com/c-sky/csky-linux
ABI Documentation:
https://github.com/c-sky/csky-doc
Here is the pre-built cross compiler for fast test from our CI:
https://gitlab.com/c-sky/buildroot/-/jobs/
101608095/artifacts/file/output/images/csky_toolchain_qemu_csky_ck807f_4.18_glibc_defconfig_482b221e52908be1c9b2ccb444255e1562bb7025.tar.xz
We use buildroot as our CI-test enviornment. "LTP, Lmbench ..." will
be tested for every commit. See here for more details:
https://gitlab.com/c-sky/buildroot/pipelines
We'll continouslly improve csky subsystem in future"
Arnd acks, and adds the following notes:
"I did a thorough review of the ABI, which as usual mainly consists of
spotting any files that don't use the asm-generic ABI itself, and
having it changed to it matches exactly what we do on other new
architectures.
I also looked at every other patch and commented on maybe half of them
where I saw something that did not quite seem right. Others have
reviewed specific patches in greater depth. I'm sure that one could
fine more of the minor details, but as long as they are not ABI
relevant, they can be fixed later.
The only patch that is part of the ABI and that nobody reviewed is the
signal handling. This is one of the areas I never worked on in much
detail. I did not see anything wrong with it, but I also don't know
what the problems with the other architectures are here, and we seem
to be hitting issues occasionally, and we never managed to generalize
this enough for new architectures to have a trivial implementation.
I was originally hoping that we could have the 64-bit time_t
interfaces ready in time to completely drop the 32-bit ones, but that
did not happen. We might still remove them in the next merge window
depending on whether the libc upstream people prefer to keep them or
not.
One more general comment: I think this may well be the last new CPU
architecture we ever add to the kernel. Both nds32 and c-sky are made
by companies that also work on risc-v, and generally speaking risc-v
seems to be killing off any of the minor licensable instruction set
projects, just like ARM has mostly killed off the custom
vendor-specific instruction sets already.
If we add another architecture in the future, it may instead be
something like the LLVM bitcode or WebAssembly, who knows?"
To which Geert Uytterhoeven pipes in about another architecture still in
the pipeline: Kalray MPPA.
* tag 'csky-for-linus-4.20' of https://github.com/c-sky/csky-linux: (24 commits)
dt-bindings: interrupt-controller: C-SKY APB intc
irqchip: add C-SKY APB bus interrupt controller
dt-bindings: interrupt-controller: C-SKY SMP intc
irqchip: add C-SKY SMP interrupt controller
MAINTAINERS: Add csky
dt-bindings: Add vendor prefix for csky
dt-bindings: csky CPU Bindings
csky: Misc headers
csky: SMP support
csky: Debug and Ptrace GDB
csky: User access
csky: Library functions
csky: ELF and module probe
csky: Atomic operations
csky: IRQ handling
csky: VDSO and rt_sigreturn
csky: Process management and Signal
csky: MMU and page table management
csky: Cache and TLB routines
csky: System Call
...
Linus Torvalds [Mon, 29 Oct 2018 03:17:49 +0000 (20:17 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) GRO overflow entries are not unlinked properly, resulting in list
poison pointers being dereferenced.
2) Fix bridge build with ipv6 disabled, from Nikolay Aleksandrov.
3) Direct packet access and other fixes in BPF from Daniel Borkmann.
4) gred_change_table_def() gets passed the wrong pointer, a pointer to
a set of unparsed attributes instead of the attribute itself. From
Jakub Kicinski.
5) Allow macsec device to be brought up even if it's lowerdev is down,
from Sabrina Dubroca.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: diag: document swapped src/dst in udp_dump_one.
macsec: let the administrator set UP state even if lowerdev is down
macsec: update operstate when lower device changes
net: sched: gred: pass the right attribute to gred_change_table_def()
ptp: drop redundant kasprintf() to create worker name
net: bridge: remove ipv6 zero address check in mcast queries
net: Properly unlink GRO packets on overflow.
bpf: fix wrong helper enablement in cgroup local storage
bpf: add bpf_jit_limit knob to restrict unpriv allocations
bpf: make direct packet write unclone more robust
bpf: fix leaking uninitialized memory on pop/peek helpers
bpf: fix direct packet write into pop/peek helpers
bpf: fix cg_skb types to hint access type in may_access_direct_pkt_data
bpf: fix direct packet access for flow dissector progs
bpf: disallow direct packet access for unpriv in cg_skb
bpf: fix test suite to enable all unpriv program types
bpf, btf: fix a missing check bug in btf_parse
selftests/bpf: add config fragments BPF_STREAM_PARSER and XDP_SOCKETS
bpf: devmap: fix wrong interface selection in notifier_call
Lorenzo Colitti [Mon, 29 Oct 2018 00:15:22 +0000 (09:15 +0900)]
net: diag: document swapped src/dst in udp_dump_one.
Since its inception, udp_dump_one has had a bug where userspace
needs to swap src and dst addresses and ports in order to find
the socket it wants. This is because it passes the socket source
address to __udp[46]_lib_lookup's saddr argument, but those
functions are intended to find local sockets matching received
packets, so saddr is the remote address, not the local address.
This can no longer be fixed for backwards compatibility reasons,
so add a brief comment explaining that this is the case. This
will avoid confusion and help ensure SOCK_DIAG implementations
of new protocols don't have the same problem.
Fixes:
a925aa00a55 ("udp_diag: Implement the get_exact dumping functionality")
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 29 Oct 2018 02:26:43 +0000 (19:26 -0700)]
Merge branch 'macsec-fixes'
Sabrina Dubroca says:
====================
macsec: linkstate fixes
This series fixes issues with handling administrative and operstate of
macsec devices.
Radu Rendec proposed another version of the first patch [0] but I'd
rather not follow the behavior of vlan devices, going with macvlan
does instead. Patrick Talbert also reported the same issue to me.
The second patch is a follow-up. The restriction on setting the device
up is a bit unreasonable, and operstate provides the information we
need in this case.
[0] https://patchwork.ozlabs.org/patch/971374/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Sun, 28 Oct 2018 08:33:10 +0000 (09:33 +0100)]
macsec: let the administrator set UP state even if lowerdev is down
Currently, the kernel doesn't let the administrator set a macsec device
up unless its lower device is currently up. This is inconsistent, as a
macsec device that is up won't automatically go down when its lower
device goes down.
Now that linkstate propagation works, there's really no reason for this
limitation, so let's remove it.
Fixes:
c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Reported-by: Radu Rendec <radu.rendec@gmail.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Sun, 28 Oct 2018 08:33:09 +0000 (09:33 +0100)]
macsec: update operstate when lower device changes
Like all other virtual devices (macvlan, vlan), the operstate of a
macsec device should match the state of its lower device. This is done
by calling netif_stacked_transfer_operstate from its netdevice notifier.
We also need to call netif_stacked_transfer_operstate when a new macsec
device is created, so that its operstate is set properly. This is only
relevant when we try to bring the device up directly when we create it.
Radu Rendec proposed a similar patch, inspired from the 802.1q driver,
that included changing the administrative state of the macsec device,
instead of just the operstate. This version is similar to what the
macvlan driver does, and updates only the operstate.
Fixes:
c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Reported-by: Radu Rendec <radu.rendec@gmail.com>
Reported-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 26 Oct 2018 22:51:06 +0000 (15:51 -0700)]
net: sched: gred: pass the right attribute to gred_change_table_def()
gred_change_table_def() takes a pointer to TCA_GRED_DPS attribute,
and expects it will be able to interpret its contents as
struct tc_gred_sopt. Pass the correct gred attribute, instead of
TCA_OPTIONS.
This bug meant the table definition could never be changed after
Qdisc was initialized (unless whatever TCA_OPTIONS contained both
passed netlink validation and was a valid struct tc_gred_sopt...).
Old behaviour:
$ ip link add type dummy
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
RTNETLINK answers: Invalid argument
Now:
$ ip link add type dummy
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
Fixes:
f62d6b936df5 ("[PKT_SCHED]: GRED: Use central VQ change procedure")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rasmus Villemoes [Fri, 26 Oct 2018 21:22:59 +0000 (23:22 +0200)]
ptp: drop redundant kasprintf() to create worker name
Building with -Wformat-nonliteral, gcc complains
drivers/ptp/ptp_clock.c: In function ‘ptp_clock_register’:
drivers/ptp/ptp_clock.c:239:26: warning: format not a string literal and no format arguments [-Wformat-nonliteral]
worker_name : info->name);
kthread_create_worker takes fmt+varargs to set the name of the
worker, and that happens with a vsnprintf() to a stack buffer (that is
then copied into task_comm). So there's no reason not to just pass
"ptp%d", ptp->index to kthread_create_worker() and avoid the
intermediate worker_name variable.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Sat, 27 Oct 2018 09:07:47 +0000 (12:07 +0300)]
net: bridge: remove ipv6 zero address check in mcast queries
Recently a check was added which prevents marking of routers with zero
source address, but for IPv6 that cannot happen as the relevant RFCs
actually forbid such packets:
RFC 2710 (MLDv1):
"To be valid, the Query message MUST
come from a link-local IPv6 Source Address, be at least 24 octets
long, and have a correct MLD checksum."
Same goes for RFC 3810.
And also it can be seen as a requirement in ipv6_mc_check_mld_query()
which is used by the bridge to validate the message before processing
it. Thus any queries with :: source address won't be processed anyway.
So just remove the check for zero IPv6 source address from the query
processing function.
Fixes:
5a2de63fd1a5 ("bridge: do not add port to router list when receives query with source 0.0.0.0")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 29 Oct 2018 00:49:53 +0000 (17:49 -0700)]
Merge tag 'drm-next-2018-10-24' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is going to rebuild more than drm as it adds a new helper to
list.h for doing bulk updates. Seemed like a reasonable addition to
me.
Otherwise the usual merge window stuff lots of i915 and amdgpu, not so
much nouveau, and piles of everything else.
Core:
- Adds a new list.h helper for doing bulk list updates for TTM.
- Don't leak fb address in smem_start to userspace (comes with EXPORT
workaround for people using mali out of tree hacks)
- udmabuf device to turn memfd regions into dma-buf
- Per-plane blend mode property
- ref/unref replacements with get/put
- fbdev conflicting framebuffers code cleaned up
- host-endian format variants
- panel orientation quirk for Acer One 10
bridge:
- TI SN65DSI86 chip support
vkms:
- GEM support.
- Cursor support
amdgpu:
- Merge amdkfd and amdgpu into one module
- CEC over DP AUX support
- Picasso APU support + VCN dynamic powergating
- Raven2 APU support
- Vega20 enablement + kfd support
- ACP powergating improvements
- ABGR/XBGR display support
- VCN jpeg support
- xGMI support
- DC i2c/aux cleanup
- Ycbcr 4:2:0 support
- GPUVM improvements
- Powerplay and powerplay endian fixes
- Display underflow fixes
vmwgfx:
- Move vmwgfx specific TTM code to vmwgfx
- Split out vmwgfx buffer/resource validation code
- Atomic operation rework
bochs:
- use more helpers
- format/byteorder improvements
qxl:
- use more helpers
i915:
- GGTT coherency getparam
- Turn off resource streamer API
- More Icelake enablement + DMC firmware
- Full PPGTT for Ivybridge, Haswell and Valleyview
- DDB distribution based on resolution
- Limited range DP display support
nouveau:
- CEC over DP AUX support
- Initial HDMI 2.0 support
virtio-gpu:
- vmap support for PRIME objects
tegra:
- Initial Tegra194 support
- DMA/IOMMU integration fixes
msm:
- a6xx perf improvements + clock prefix
- GPU preemption optimisations
- a6xx devfreq support
- cursor support
rockchip:
- PX30 support
- rgb output interface support
mediatek:
- HDMI output support on mt2701 and mt7623
rcar-du:
- Interlaced modes on Gen3
- LVDS on R8A77980
- D3 and E3 SoC support
hisilicon:
- misc fixes
mxsfb:
- runtime pm support
sun4i:
- R40 TCON support
- Allwinner A64 support
- R40 HDMI support
omapdrm:
- Driver rework changing display pipeline ordering to use common code
- DMM memory barrier and irq fixes
- Errata workarounds
exynos:
- out-bridge support for LVDS bridge driver
- Samsung 16x16 tiled format support
- Plane alpha and pixel blend mode support
tilcdc:
- suspend/resume update
mali-dp:
- misc updates"
* tag 'drm-next-2018-10-24' of git://anongit.freedesktop.org/drm/drm: (1382 commits)
firmware/dmc/icl: Add missing MODULE_FIRMWARE() for Icelake.
drm/i915/icl: Fix signal_levels
drm/i915/icl: Fix DDI/TC port clk_off bits
drm/i915/icl: create function to identify combophy port
drm/i915/gen9+: Fix initial readout for Y tiled framebuffers
drm/i915: Large page offsets for pread/pwrite
drm/i915/selftests: Disable shrinker across mmap-exhaustion
drm/i915/dp: Link train Fallback on eDP only if fallback link BW can fit panel's native mode
drm/i915: Fix intel_dp_mst_best_encoder()
drm/i915: Skip vcpi allocation for MSTB ports that are gone
drm/i915: Don't unset intel_connector->mst_port
drm/i915: Only reset seqno if actually idle
drm/i915: Use the correct crtc when sanitizing plane mapping
drm/i915: Restore vblank interrupts earlier
drm/i915: Check fb stride against plane max stride
drm/amdgpu/vcn:Fix uninitialized symbol error
drm: panel-orientation-quirks: Add quirk for Acer One 10 (S1003)
drm/amd/amdgpu: Fix debugfs error handling
drm/amdgpu: Update gc_9_0 golden settings.
drm/amd/powerplay: update PPtable with DC BTC and Tvr SocLimit fields
...
Linus Torvalds [Sun, 28 Oct 2018 20:26:45 +0000 (13:26 -0700)]
Merge tag 'vla-v4.20-rc1' of git://git./linux/kernel/git/kees/linux
Pull VLA removal from Kees Cook:
"Globally warn on VLA use.
This turns on "-Wvla" globally now that the last few trees with their
VLA removals have landed (crypto, block, net, and powerpc).
Arnd mentioned that there may be a couple more VLAs hiding in
hard-to-find randconfigs, but nothing big has shaken out in the last
month or so in linux-next.
We should be basically VLA-free now! Wheee. :)
Summary:
- Remove unused fallback for BUILD_BUG_ON (which technically contains
a VLA)
- Lift -Wvla to the top-level Makefile"
* tag 'vla-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
Makefile: Globally enable VLA warning
compiler.h: give up __compiletime_assert_fallback()
Linus Torvalds [Sun, 28 Oct 2018 20:22:35 +0000 (13:22 -0700)]
Merge tag 'kbuild-v4.20' of git://git./linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- optimize kallsyms slightly
- remove check for old CFLAGS usage
- add some compiler flags unconditionally instead of evaluating
$(call cc-option,...)
- fix variable shadowing in host tools
- refactor scripts/mkmakefile
- refactor various makefiles
* tag 'kbuild-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
modpost: Create macro to avoid variable shadowing
ASN.1: Remove unnecessary shadowed local variable
kbuild: use 'else ifeq' for checksrc to improve readability
kbuild: remove unneeded link_multi_deps
kbuild: add -Wno-unused-but-set-variable flag unconditionally
kbuild: add -Wdeclaration-after-statement flag unconditionally
kbuild: add -Wno-pointer-sign flag unconditionally
modpost: remove leftover symbol prefix handling for module device table
kbuild: simplify command line creation in scripts/mkmakefile
kbuild: do not pass $(objtree) to scripts/mkmakefile
kbuild: remove user ID check in scripts/mkmakefile
kbuild: remove VERSION and PATCHLEVEL from $(objtree)/Makefile
kbuild: add --include-dir flag only for out-of-tree build
kbuild: remove dead code in cmd_files calculation in top Makefile
kbuild: hide most of targets when running config or mixed targets
kbuild: remove old check for CFLAGS use
kbuild: prefix Makefile.dtbinst path with $(srctree) unconditionally
kallsyms: remove left-over Blackfin code
kallsyms: reduce size a little on 64-bit
Linus Torvalds [Sun, 28 Oct 2018 19:58:42 +0000 (12:58 -0700)]
Merge tag 'linux-kselftest-4.20-rc1' of git://git./linux/kernel/git/shuah/linux-kselftest
Pull kselftest updates from Shuah Khan:
"This Kselftest update for Linux 4.20-rc1 consists of:
- Improvements to ftrace test suite from Masami Hiramatsu.
- Color coded ftrace PASS / FAIL results from Steven Rostedt (VMware)
to improve readability of reports.
- watchdog Fixes and enhancement to add gettimeout and get|set
pretimeout options from Jerry Hoemann.
- Several fixes to warnings and spelling etc"
* tag 'linux-kselftest-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (40 commits)
selftests/ftrace: Strip escape sequences for log file
selftests/ftrace: Use colored output when available
selftests: fix warning: "_GNU_SOURCE" redefined
selftests: kvm: Fix -Wformat warnings
selftests/ftrace: Add color to the PASS / FAIL results
kvm: selftests: fix spelling mistake "Insufficent" -> "Insufficient"
selftests: gpio: Fix OUTPUT directory in Makefile
selftests: gpio: restructure Makefile
selftests: watchdog: Fix ioctl SET* error paths to take oneshot exit path
selftests: watchdog: Add gettimeout and get|set pretimeout
selftests: watchdog: Fix error message.
selftests: watchdog: fix message when /dev/watchdog open fails
selftests/ftrace: Add ftrace cpumask testcase
selftests/ftrace: Add wakeup_rt tracer testcase
selftests/ftrace: Add wakeup tracer testcase
selftests/ftrace: Add stacktrace ftrace filter command testcase
selftests/ftrace: Add trace_pipe testcase
selftests/ftrace: Add function filter on module testcase
selftests/ftrace: Add max stack tracer testcase
selftests/ftrace: Add function profiling stat testcase
...
Linus Torvalds [Sun, 28 Oct 2018 18:35:40 +0000 (11:35 -0700)]
Merge branch 'xarray' of git://git.infradead.org/users/willy/linux-dax
Pull XArray conversion from Matthew Wilcox:
"The XArray provides an improved interface to the radix tree data
structure, providing locking as part of the API, specifying GFP flags
at allocation time, eliminating preloading, less re-walking the tree,
more efficient iterations and not exposing RCU-protected pointers to
its users.
This patch set
1. Introduces the XArray implementation
2. Converts the pagecache to use it
3. Converts memremap to use it
The page cache is the most complex and important user of the radix
tree, so converting it was most important. Converting the memremap
code removes the only other user of the multiorder code, which allows
us to remove the radix tree code that supported it.
I have 40+ followup patches to convert many other users of the radix
tree over to the XArray, but I'd like to get this part in first. The
other conversions haven't been in linux-next and aren't suitable for
applying yet, but you can see them in the xarray-conv branch if you're
interested"
* 'xarray' of git://git.infradead.org/users/willy/linux-dax: (90 commits)
radix tree: Remove multiorder support
radix tree test: Convert multiorder tests to XArray
radix tree tests: Convert item_delete_rcu to XArray
radix tree tests: Convert item_kill_tree to XArray
radix tree tests: Move item_insert_order
radix tree test suite: Remove multiorder benchmarking
radix tree test suite: Remove __item_insert
memremap: Convert to XArray
xarray: Add range store functionality
xarray: Move multiorder_check to in-kernel tests
xarray: Move multiorder_shrink to kernel tests
xarray: Move multiorder account test in-kernel
radix tree test suite: Convert iteration test to XArray
radix tree test suite: Convert tag_tagged_items to XArray
radix tree: Remove radix_tree_clear_tags
radix tree: Remove radix_tree_maybe_preload_order
radix tree: Remove split/join code
radix tree: Remove radix_tree_update_node_t
page cache: Finish XArray conversion
dax: Convert page fault handlers to XArray
...
David S. Miller [Sun, 28 Oct 2018 17:35:12 +0000 (10:35 -0700)]
net: Properly unlink GRO packets on overflow.
Just like with normal GRO processing, we have to initialize
skb->next to NULL when we unlink overflow packets from the
GRO hash lists.
Fixes:
d4546c2509b1 ("net: Convert GRO SKB handling to list_head.")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leonardo Bras [Wed, 24 Oct 2018 04:03:52 +0000 (01:03 -0300)]
modpost: Create macro to avoid variable shadowing
Create DEF_FIELD_ADDR_VAR as a more generic version of the DEF_FIELD_ADD
macro, allowing usage of a variable name other than the struct element name.
Also, sets DEF_FIELD_ADDR as a specific usage of DEF_FILD_ADDR_VAR in which
the var name is the same as the struct element name.
Then, makes use of DEF_FIELD_ADDR_VAR to create a variable of another name,
in order to avoid variable shadowing.
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Leonardo Bras [Wed, 24 Oct 2018 04:03:51 +0000 (01:03 -0300)]
ASN.1: Remove unnecessary shadowed local variable
Remove an unnecessary shadowed local variable (start).
It was used only once, with the same value it was started before
the if block.
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
John David Anglin [Sat, 27 Oct 2018 22:03:25 +0000 (18:03 -0400)]
parisc: Fix A500 boot crash
I believe the following change will fix the cache/TLB inconsistency
observed by Meelis. After changing the page table entries, we need to
flush the cache and TLB to ensure that we don't have any stale PTE
values in the cache or TLB.
The alternative patching is done after all CPUs are running. Thus, we
need to flush the whole cache and TLB.
I included the init section in the range modified by map_pages as
suggested by Helge. Some routines in the init section may require
patching.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Linus Torvalds [Sat, 27 Oct 2018 18:03:27 +0000 (11:03 -0700)]
HID: we do not randomly make new drivers 'default y'
.. even when that "default y" is hidden syntactically as a
default !EXPERT
it's wrong.
The only reason something should be 'default y' is if it used to be
built-in, and it was made configurable, and the 'default y' is just
retaining the status quo.
Altheratively, the hardware for the driver has become _so_ common that
it really makes sense for everybody to build it. Finally, one possible
reason for 'default y' is because the option is not enabling any new
code at all, but is just enabling other options (the networking people
do this for vendor options, for example, so that you can disable whole
vendors at a time).
Clearly, none of these cases hold for the BigBen Interactive Kids'
gamepad, and HID_BIGBEN_FF should thus most definitely not default
to on for everybody.
Cc: Hanno Zulla <kontakt@hanno.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 27 Oct 2018 17:25:22 +0000 (10:25 -0700)]
Merge tag 'linux-watchdog-4.20-rc1' of git://linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- Add Armada 37xx CPU watchdog
- w83627hf_wdt: Add Support for NCT6796D, NCT6797D, NCT6798D
- hpwdt: several improvements
- renesas_wdt: SPDX identifiers, stop when unregistering, support for
R7S9210
- rza_wdt: SPDX identifiers, support longer timeouts
- core: fix null pointer dereference when releasing cdev
- iTCO_wdt: Drop option vendorsupport=2
- sama5d4: fix timeout-sec usage
- lantiq_wdt: convert to watchdog framework
- several small fixes
* tag 'linux-watchdog-4.20-rc1' of git://www.linux-watchdog.org/linux-watchdog: (30 commits)
watchdog: ts4800: release syscon device node in ts4800_wdt_probe()
watchdog: armada_37xx_wdt: use do_div for u64 division
documentation: watchdog: add documentation for armada-37xx-wdt
dt-bindings: watchdog: Document armada-37xx-wdt binding
watchdog: Add support for Armada 37xx CPU watchdog
dt-bindings: watchdog: add mpc8xxx-wdt support
watchdog: mpc8xxx: provide boot status
MAINTAINERS: Fix file pattern for MEN Z069 watchdog driver
dt-bindings: watchdog: renesas-wdt: Add support for R7S9210
watchdog: rza_wdt: Support longer timeouts
watchdog: hpwdt: Disable PreTimeout when Timeout is smaller
watchdog: w83627hf_wdt: Support NCT6796D, NCT6797D, NCT6798D
watchdog: mpc8xxx: use dev_xxxx() instead of pr_xxxx()
watchdog: lantiq: add get_timeleft callback
watchdog: lantiq: Convert to watchdog_device
watchdog: lantiq: update register names to better match spec
watchdog: sama5d4: fix timeout-sec usage
watchdog: fix a small number of "watchog" typos in comments
watchdog: rza_wdt: convert to SPDX identifiers
watchdog: iTCO_wdt: Remove unused hooks
...
Linus Torvalds [Sat, 27 Oct 2018 17:20:39 +0000 (10:20 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"Just random driver fixups, nothing exiting"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - avoid using uninitialized variable when probing
Input: xen-kbdfront - mark expected switch fall-through
Input: atmel_mxt_ts - mark expected switch fall-through
Input: cyapa - mark expected switch fall-throughs
Input: wm97xx-ts - fix exit path
Input: of_touchscreen - add support for touchscreen-min-x|y
Input: Fix DIR-685 touchkeys MAINTAINERS entry
Input: elants_i2c - use DMA safe i2c when possible
Input: silead - try firmware reload after unsuccessful resume
Input: st1232 - set INPUT_PROP_DIRECT property
Input: xilinx_ps2 - convert to using %pOFn instead of device_node.name
Input: atmel_mxt_ts - fix multiple <linux/property.h> includes
Input: sun4i-lradc - convert to using %pOFn instead of device_node.name
Input: pwm-vibrator - correct pwms in DT binding example
Linus Torvalds [Sat, 27 Oct 2018 16:24:24 +0000 (09:24 -0700)]
Merge tag 'rtc-4.20' of git://git./linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"This cycle, there were mostly non urgent fixes in drivers. I also
finally unexported the non managed registration.
Subsystem:
- non devm managed registration is now removed from the driver API
- all the unnecessary rtc_valid_tm() calls have been removed
Drivers:
- abx80X: watchdog support
- cmos: fix non ACPI support
- sc27xx: fix alarm support
- Remove a possible sysfs race condition for ab8500, ds1307, ds1685,
isl1208
- Fix a possible race condition where an irq handler may be called
before the rtc_device struct is allocated for mt6397, pl030,
menelaus, armada38x"
* tag 'rtc-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (54 commits)
rtc: sc27xx: Always read normal alarm when registering RTC device
rtc: sc27xx: Add check to see if need to enable the alarm interrupt
rtc: sc27xx: Remove interrupts disable and clear in probe()
rtc: sc27xx: Clear SPG value update interrupt status
rtc: sc27xx: Set wakeup capability before registering rtc device
rtc: s35390a: Change buf's type to u8 in s35390a_init
rtc: ds1307: fix ds1339 wakealarm support
rtc: ds1685: simplify getting .driver_data
rtc: m41t80: mark expected switch fall-through
rtc: tegra: Propagate errors from platform_get_irq()
rtc: cmos: Remove the `use_acpi_alarm' module parameter for !ACPI
rtc: cmos: Fix non-ACPI undefined reference to `hpet_rtc_interrupt'
rtc: mv: let the core handle invalid alarms
rtc: vr41xx: switch to rtc_time64_to_tm/rtc_tm_to_time64
rtc: ab8500: remove useless check
rtc: ab8500: let the core handle range
rtc: ab8500: use rtc_add_group
rtc: rs5c348: report error when time is invalid
rtc: rs5c348: remove forward declaration
rtc: rs5c348: remove useless label
...
Linus Torvalds [Sat, 27 Oct 2018 16:20:42 +0000 (09:20 -0700)]
Merge tag 'led-fix-for-4.20-rc1' of git://git./linux/kernel/git/j.anaszewski/linux-leds
Pull LED fix from Jacek Anaszewski.
* tag 'led-fix-for-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: gpio: set led_dat->gpiod pointer for OF defined GPIO leds