git.osdn.net Git - tomoyo/tomoyo-test1.git/log

hsr: use netdev_err() instead of WARN_ONCE()

When HSR interface is sending a frame, it finds a node with
the destination ethernet address from the list.
If there is no node, it calls WARN_ONCE().
But, using WARN_ONCE() for this situation is a little bit overdoing.
So, in this patch, the netdev_err() is used instead.

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hsr: use extack error message instead of netdev_info

If HSR uses the extack instead of netdev_info(), users can get
error messages immediately without any checking the kernel message.

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hsr: use debugfs_remove_recursive() instead of debugfs_remove()

If it uses debugfs_remove_recursive() instead of debugfs_remove(),
hsr_priv() doesn't need to have "node_tbl_file" pointer variable.

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ag71xx: port to phylink

The port to phylink was done as close as possible to initial
functionality.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-ll_temac-RX-TX-ring-size-and-coalesce-ethtool-parameters'

Esben Haabendal says:

====================
net: ll_temac: RX/TX ring size and coalesce ethtool parameters

This series adds support for RX/TX ring size and irq coalesce ethtool
parameters to ll_temac driver.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: ll_temac: Add ethtool support for coalesce parameters

Please note that the delays are calculated based on typical
parameters. But as TEMAC is an HDL IP, designs may vary, and future
work might be needed to make this calculation configurable.

Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ll_temac: Make RX/TX ring sizes configurable

Add support for setting the RX and TX ring sizes for this driver using
ethtool. Also increase the default RX ring size as the previous default
was far too low for good performance in some configurations.

Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ll_temac: Remove unused start_p variable

The start_p variable was included in the initial commit,
commit 92744989533c ("net: add Xilinx ll_temac device driver"),
but has never had any real use.

Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ll_temac: Remove unused tx_bd_next struct field

The tx_bd_next field was included in the initial commit,
commit 92744989533c ("net: add Xilinx ll_temac device driver"),
but has never had any real use.

Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: Replace zero-length array with flexible-array member

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
int stuff;
struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git./linux/kernel/git/bpf/bpf-next

Alexei Starovoitov says:

====================
pull-request: bpf-next 2020-02-28

The following pull-request contains BPF updates for your *net-next* tree.

We've added 41 non-merge commits during the last 7 day(s) which contain
a total of 49 files changed, 1383 insertions(+), 499 deletions(-).

The main changes are:

1) BPF and Real-Time nicely co-exist.

2) bpftool feature improvements.

3) retrieve bpf_sk_storage via INET_DIAG.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-cleanup-datagram-receive-helpers'

Paolo Abeni says:

====================
net: cleanup datagram receive helpers

Several receive helpers have an optional destructor argument, which uglify
the code a bit and is taxed by retpoline overhead.

This series refactor the code so that we can drop such optional argument,
cleaning the helpers a bit and avoiding an indirect call in fast path.

The first patch refactor a bit the caller, so that the second patch
actually dropping the argument is more straight-forward

v1 -> v2:
- call scm_stat_del() only when not peeking - Kirill
- fix build issue with CONFIG_INET_ESPINTCP
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: datagram: drop 'destructor' argument from several helpers

The only users for such argument are the UDP protocol and the UNIX
socket family. We can safely reclaim the accounted memory directly
from the UDP code and, after the previous patch, we can do scm
stats accounting outside the datagram helpers.

Overall this cleans up a bit some datagram-related helpers, and
avoids an indirect call per packet in the UDP receive path.

v1 -> v2:
- call scm_stat_del() only when not peeking - Kirill
- fix build issue with CONFIG_INET_ESPINTCP

Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

unix: uses an atomic type for scm files accounting

So the scm_stat_{add,del} helper can be invoked with no
additional lock held.

This clean-up the code a bit and will make the next
patch easier.

Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

af_unix: Replace zero-length array with flexible-array member

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
int stuff;
struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: Replace zero-length array with flexible-array member

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
int stuff;
struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: core: Replace zero-length array with flexible-array member

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
int stuff;
struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Replace zero-length array with flexible-array member

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
int stuff;
struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dccp: Replace zero-length array with flexible-array member

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
int stuff;
struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

l2tp: Replace zero-length array with flexible-array member

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
int stuff;
struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

Lastly, fix the following checkpatch warning:
CHECK: Prefer kernel type 'u8' over 'uint8_t'
#50: FILE: net/l2tp/l2tp_core.h:119:
+ uint8_t priv[]; /* private data */

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mpls: Replace zero-length array with flexible-array member

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
int stuff;
struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xdp: Replace zero-length array with flexible-array member

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
int stuff;
struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mlx5-updates-2020-02-27' of git://git./linux/kernel/git/saeed/linux

Saeed Mahameed says:

====================
mlx5-updates-2020-02-27

mlx5 misc updates and minor cleanups:

1) Use per vport tables for mirroring
2) Improve log messages for SW steering (DR)
3) Add devlink fdb_large_groups parameter
4) E-Switch, Allow goto earlier chain
5) Don't allow forwarding between uplink representors
6) Add support for devlink-port in non-representors mode
7) Minor misc cleanups
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'bpf_sk_storage_via_inet_diag'

Martin KaFai Lau says:

====================
The bpf_prog can store specific info to a sk by using bpf_sk_storage.
In other words, a sk can be extended by a bpf_prog.

This series is to support providing bpf_sk_storage data during inet_diag's
dump. The primary target is the usage like iproute2's "ss".

The first two patches are refactoring works in inet_diag to make
adding bpf_sk_storage support easier. The next two patches do
the actual work.

Please see individual patch for details.

v2:
- Add commit message for u16 to u32 change in min_dump_alloc in Patch 4 (Song)
- Add comment to explain the !skb->len check in __inet_diag_dump in Patch 4.
- Do the map->map_type check earlier in Patch 3 for readability.
====================

Signed-off-by: Alexei Starovoitov <ast@kernel.org>

bpf: inet_diag: Dump bpf_sk_storages in inet_diag_dump()

This patch will dump out the bpf_sk_storages of a sk
if the request has the INET_DIAG_REQ_SK_BPF_STORAGES nlattr.

An array of SK_DIAG_BPF_STORAGE_REQ_MAP_FD can be specified in
INET_DIAG_REQ_SK_BPF_STORAGES to select which bpf_sk_storage to dump.
If no map_fd is specified, all bpf_sk_storages of a sk will be dumped.

bpf_sk_storages can be added to the system at runtime.  It is difficult
to find a proper static value for cb->min_dump_alloc.

This patch learns the nlattr size required to dump the bpf_sk_storages
of a sk.  If it happens to be the very first nlmsg of a dump and it
cannot fit the needed bpf_sk_storages,  it will try to expand the
skb by "pskb_expand_head()".

Instead of expanding it in inet_sk_diag_fill(), it is expanded at a
sleepable context in __inet_diag_dump() so __GFP_DIRECT_RECLAIM can
be used.  In __inet_diag_dump(), it will retry as long as the
skb is empty and the cb->min_dump_alloc becomes larger than before.
cb->min_dump_alloc is bounded by KMALLOC_MAX_SIZE.  The min_dump_alloc
is also changed from 'u16' to 'u32' to accommodate a sk that may have
a few large bpf_sk_storages.

The updated cb->min_dump_alloc will also be used to allocate the skb in
the next dump.  This logic already exists in netlink_dump().

Here is the sample output of a locally modified 'ss' and it could be made
more readable by using BTF later:
[root@arch-fb-vm1 ~]# ss --bpf-map-id 14 --bpf-map-id 13 -t6an 'dst [::1]:8989'
State Recv-Q Send-Q Local Address:Port  Peer Address:PortProcess
ESTAB 0      0              [::1]:51072        [::1]:8989
bpf_map_id:14 value:[ 3feb ]
bpf_map_id:13 value:[ 3f ]
ESTAB 0      0              [::1]:51070        [::1]:8989
bpf_map_id:14 value:[ 3feb ]
bpf_map_id:13 value:[ 3f ]

[root@arch-fb-vm1 ~]# ~/devshare/github/iproute2/misc/ss --bpf-maps -t6an 'dst [::1]:8989'
State         Recv-Q         Send-Q                   Local Address:Port                    Peer Address:Port         Process
ESTAB         0              0                                [::1]:51072                          [::1]:8989
bpf_map_id:14 value:[ 3feb ]
bpf_map_id:13 value:[ 3f ]
bpf_map_id:12 value:[ 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000... total:65407 ]
ESTAB         0              0                                [::1]:51070                          [::1]:8989
bpf_map_id:14 value:[ 3feb ]
bpf_map_id:13 value:[ 3f ]
bpf_map_id:12 value:[ 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000... total:65407 ]

Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200225230427.1976129-1-kafai@fb.com

bpf: INET_DIAG support in bpf_sk_storage

This patch adds INET_DIAG support to bpf_sk_storage.

1. Although this series adds bpf_sk_storage diag capability to inet sk,
   bpf_sk_storage is in general applicable to all fullsock.  Hence, the
   bpf_sk_storage logic will operate on SK_DIAG_* nlattr.  The caller
   will pass in its specific nesting nlattr (e.g. INET_DIAG_*) as
   the argument.

2. The request will be like:
INET_DIAG_REQ_SK_BPF_STORAGES (nla_nest) (defined in latter patch)
SK_DIAG_BPF_STORAGE_REQ_MAP_FD (nla_put_u32)
SK_DIAG_BPF_STORAGE_REQ_MAP_FD (nla_put_u32)
......

   Considering there could have multiple bpf_sk_storages in a sk,
   instead of reusing INET_DIAG_INFO ("ss -i"),  the user can select
   some specific bpf_sk_storage to dump by specifying an array of
   SK_DIAG_BPF_STORAGE_REQ_MAP_FD.

   If no SK_DIAG_BPF_STORAGE_REQ_MAP_FD is specified (i.e. an empty
   INET_DIAG_REQ_SK_BPF_STORAGES), it will dump all bpf_sk_storages
   of a sk.

3. The reply will be like:
INET_DIAG_BPF_SK_STORAGES (nla_nest) (defined in latter patch)
SK_DIAG_BPF_STORAGE (nla_nest)
SK_DIAG_BPF_STORAGE_MAP_ID (nla_put_u32)
SK_DIAG_BPF_STORAGE_MAP_VALUE (nla_reserve_64bit)
SK_DIAG_BPF_STORAGE (nla_nest)
SK_DIAG_BPF_STORAGE_MAP_ID (nla_put_u32)
SK_DIAG_BPF_STORAGE_MAP_VALUE (nla_reserve_64bit)
......

4. Unlike other INET_DIAG info of a sk which is pretty static, the size
   required to dump the bpf_sk_storage(s) of a sk is dynamic as the
   system adding more bpf_sk_storage_map.  It is hard to set a static
   min_dump_alloc size.

   Hence, this series learns it at the runtime and adjust the
   cb->min_dump_alloc as it iterates all sk(s) of a system.  The
   "unsigned int *res_diag_size" in bpf_sk_storage_diag_put()
   is for this purpose.

   The next patch will update the cb->min_dump_alloc as it
   iterates the sk(s).

Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200225230421.1975729-1-kafai@fb.com

inet_diag: Move the INET_DIAG_REQ_BYTECODE nlattr to cb->data

The INET_DIAG_REQ_BYTECODE nlattr is currently re-found every time when
the "dump()" is re-started.

In a latter patch, it will also need to parse the new
INET_DIAG_REQ_SK_BPF_STORAGES nlattr to learn the map_fds. Thus, this
patch takes this chance to store the parsed nlattr in cb->data
during the "start" time of a dump.

By doing this, the "bc" argument also becomes unnecessary
and is removed. Also, the two copies of the INET_DIAG_REQ_BYTECODE
parsing-audit logic between compat/current version can be
consolidated to one.

Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200225230415.1975555-1-kafai@fb.com

inet_diag: Refactor inet_sk_diag_fill(), dump(), and dump_one()

In a latter patch, there is a need to update "cb->min_dump_alloc"
in inet_sk_diag_fill() as it learns the diffierent bpf_sk_storages
stored in a sk while dumping all sk(s) (e.g. tcp_hashinfo).

The inet_sk_diag_fill() currently does not take the "cb" as an argument.
One of the reason is inet_sk_diag_fill() is used by both dump_one()
and dump() (which belong to the "struct inet_diag_handler".  The dump_one()
interface does not pass the "cb" along.

This patch is to make dump_one() pass a "cb".  The "cb" is created in
inet_diag_cmd_exact().  The "nlh" and "in_skb" are stored in "cb" as
the dump() interface does.  The total number of args in
inet_sk_diag_fill() is also cut from 10 to 7 and
that helps many callers to pass fewer args.

In particular,
"struct user_namespace *user_ns", "u32 pid", and "u32 seq"
can be replaced by accessing "cb->nlh" and "cb->skb".

A similar argument reduction is also made to
inet_twsk_diag_fill() and inet_req_diag_fill().

inet_csk_diag_dump() and inet_csk_diag_fill() are also removed.
They are mostly equivalent to inet_sk_diag_fill().  Their repeated
usages are very limited.  Thus, inet_sk_diag_fill() is directly used
in those occasions.

Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200225230409.1975173-1-kafai@fb.com

Merge git://git./linux/kernel/git/netdev/net

The mptcp conflict was overlapping additions.

The SMC conflict was an additional and removal happening at the same
time.

Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: Remove redundant comment about goto slow path

The code is self explanatory and makes the comment redundant.

Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Reduce number of arguments in slow path handling

mlx5e_tc_offload_to_slow_path() and mlx5e_tc_unoffload_from_slow_path()
take an extra argument allocated on the stack of the caller but not used
by the caller. Avoid the extra argument and use local variable in the
function itself.

Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Remove unused argument from parse_tc_pedit_action()

parse_attr is not used by parse_tc_pedit_action() so revmove it.

Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Use NL_SET_ERR_MSG_MOD() extack for errors

This to be consistent and adds the module name to the error message.

Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Use netdev_warn() instead of pr_err() for errors

This is for added netdev prefix that helps identify
the source of the message.

Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Use netdev_warn() for errors for added prefix

This helps identify the source of the message.
If netdev still doesn't exists use mlx5_core_warn().

Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: DR, Improve log messages

Few print messages are in debug level where they should be in error, and
few messages are missing.

Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: DR, Change matcher priority parameter type

Change matcher priority parameter type from u16 to u32,
this change is needed since sometimes upper levels
create a matcher with priority bigger than 2^16.

Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Add devlink fdb_large_groups parameter

Add a devlink parameter to control the number of large groups in a
autogrouped flow table. The default value is 15, and the range is between 1
and 1024.

The size of each large group can be calculated according to the following
formula: size = 4M / (fdb_large_groups + 1).

Examples:
- Set the number of large groups to 20.
    $ devlink dev param set pci/0000:82:00.0 name fdb_large_groups \
      cmode driverinit value 20

  Then run devlink reload command to apply the new value.
    $ devlink dev reload pci/0000:82:00.0

- Read the number of large groups in flow table.
    $ devlink dev param show pci/0000:82:00.0 name fdb_large_groups
    pci/0000:82:00.0:
      name fdb_large_groups type driver-specific
        values:
          cmode driverinit value 20

Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: Change the name of steering mode param id

The prefix should be "MLX5_DEVLINK_PARAM_ID_" for all in
mlx5_devlink_param_id enum.

Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Add support for devlink-port in non-representors mode

Added devlink_port field to mlx5e_priv structure and a callback to
netdev ops to enable devlink to get info about the port. The port
registration happens at driver initialization.

Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Rename representor get devlink port function

Rename representor's mlx5e_get_devlink_port() to
mlx5e_rep_get_devlink_port().
The downstream patch will add a non-representor mlx5e function called
mlx5e_get_devlink_phy_port().

Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: E-Switch, Allow goto earlier chain if FW supports it

Mellanox FW can support this if ignore_flow_level capability exists.

Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Eswitch, Use per vport tables for mirroring

When using port mirroring, we forward the traffic to another table and
use that table to forward to the mirrored vport. Since the hardware
loses the values of reg c, and in particular reg c0, we fail the match
on the input vport which previously existed in reg c0. To overcome this
situation, we use a set of per vport tables, positioned at the lowest
priority, and forward traffic to those tables. Since these tables are
per vport, we can avoid matching on reg c0.

Fixes: c01cfd0f1115 ("net/mlx5: E-Switch, Add match on vport metadata for rule in fast path")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: Eswitch, avoid redundant mask

misc_params.source_port is a 16 bit field already so no need for
redundant masking against 0xffff. Also change local variables type to
u16.

Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Don't allow forwarding between uplink

We can install forwarding packets rule between uplink
in switchdev mode, as show below. But the hardware does
not do that as expected (mlnx_perf -i $PF1, we can't get
the counter of the PF1). By the way, if we add the uplink
PF0, PF1 to Open vSwitch and enable hw-offload, the rules
can be offloaded but not work fine too. This patch add a
check and if so return -EOPNOTSUPP.

$ tc filter add dev $PF0 protocol all parent ffff: prio 1 handle 1 \
    flower skip_sw action mirred egress redirect dev $PF1

$ tc -d -s filter show dev $PF0 ingress
    skip_sw
    in_hw in_hw_count 1
    action order 1: mirred (Egress Redirect to device enp130s0f1) stolen
    ...
    Sent hardware 408954 bytes 4173 pkt
    ...

Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Merge git://git./linux/kernel/git/netdev/net

Pull networking fixes from David Miller:

1) Fix leak in nl80211 AP start where we leak the ACL memory, from
    Johannes Berg.

2) Fix double mutex unlock in mac80211, from Andrei Otcheretianski.

3) Fix RCU stall in ipset, from Jozsef Kadlecsik.

4) Fix devlink locking in devlink_dpipe_table_register, from Madhuparna
    Bhowmik.

5) Fix race causing TX hang in ll_temac, from Esben Haabendal.

6) Stale eth hdr pointer in br_dev_xmit(), from Nikolay Aleksandrov.

7) Fix TX hash calculation bounds checking wrt. tc rules, from Amritha
    Nambiar.

8) Size netlink responses properly in schedule action code to take into
    consideration TCA_ACT_FLAGS. From Jiri Pirko.

9) Fix firmware paths for mscc PHY driver, from Antoine Tenart.

10) Don't register stmmac notifier multiple times, from Aaro Koskinen.

11) Various rmnet bug fixes, from Taehee Yoo.

12) Fix vsock deadlock in vsock transport release, from Stefano
    Garzarella.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (61 commits)
  net: dsa: mv88e6xxx: Fix masking of egress port
  mlxsw: pci: Wait longer before accessing the device after reset
  sfc: fix timestamp reconstruction at 16-bit rollover points
  vsock: fix potential deadlock in transport->release()
  unix: It's CONFIG_PROC_FS not CONFIG_PROCFS
  net: rmnet: fix packet forwarding in rmnet bridge mode
  net: rmnet: fix bridge mode bugs
  net: rmnet: use upper/lower device infrastructure
  net: rmnet: do not allow to change mux id if mux id is duplicated
  net: rmnet: remove rcu_read_lock in rmnet_force_unassociate_device()
  net: rmnet: fix suspicious RCU usage
  net: rmnet: fix NULL pointer dereference in rmnet_changelink()
  net: rmnet: fix NULL pointer dereference in rmnet_newlink()
  net: phy: marvell: don't interpret PHY status unless resolved
  mlx5: register lag notifier for init network namespace only
  unix: define and set show_fdinfo only if procfs is enabled
  hinic: fix a bug of rss configuration
  hinic: fix a bug of setting hw_ioctxt
  hinic: fix a irq affinity bug
  net/smc: check for valid ib_client_data
  ...

bpf: Replace zero-length array with flexible-array member

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
int stuff;
struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200227001744.GA3317@embeddedor

net: dsa: mv88e6xxx: Fix masking of egress port

Add missing ~ to the usage of the mask.

Reported-by: Kevin Benson <Kevin.Benson@zii.aero>
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 5c74c54ce6ff ("net: dsa: mv88e6xxx: Split monitor port configuration")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: pci: Wait longer before accessing the device after reset

During initialization the driver issues a reset to the device and waits
for 100ms before checking if the firmware is ready. The waiting is
necessary because before that the device is irresponsive and the first
read can result in a completion timeout.

While 100ms is sufficient for Spectrum-1 and Spectrum-2, it is
insufficient for Spectrum-3.

Fix this by increasing the timeout to 200ms.

Fixes: da382875c616 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: reg: Update module_type values in PMTM register and map them to width

There are couple new values that PMTM register can return
in module_type field. Add them and map them to module width in
mlxsw_core_module_max_width(). Fix the existing names on the way.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

WAN: Replace zero-length array with flexible-array member

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
int stuff;
struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NFC: Replace zero-length array with flexible-array member

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
int stuff;
struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: fix timestamp reconstruction at 16-bit rollover points

We can't just use the top bits of the last sync event as they could be
off-by-one every 65,536 seconds, giving an error in reconstruction of
65,536 seconds.

This patch uses the difference in the bottom 16 bits (mod 2^16) to
calculate an offset that needs to be applied to the last sync event to
get to the current time.

Signed-off-by: Alexandru-Mihai Maftei <amaftei@solarflare.com>
Acked-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vsock: fix potential deadlock in transport->release()

Some transports (hyperv, virtio) acquire the sock lock during the
.release() callback.

In the vsock_stream_connect() we call vsock_assign_transport(); if
the socket was previously assigned to another transport, the
vsk->transport->release() is called, but the sock lock is already
held in the vsock_stream_connect(), causing a deadlock reported by
syzbot:

    INFO: task syz-executor280:9768 blocked for more than 143 seconds.
      Not tainted 5.6.0-rc1-syzkaller #0
    "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
    syz-executor280 D27912  9768   9766 0x00000000
    Call Trace:
     context_switch kernel/sched/core.c:3386 [inline]
     __schedule+0x934/0x1f90 kernel/sched/core.c:4082
     schedule+0xdc/0x2b0 kernel/sched/core.c:4156
     __lock_sock+0x165/0x290 net/core/sock.c:2413
     lock_sock_nested+0xfe/0x120 net/core/sock.c:2938
     virtio_transport_release+0xc4/0xd60 net/vmw_vsock/virtio_transport_common.c:832
     vsock_assign_transport+0xf3/0x3b0 net/vmw_vsock/af_vsock.c:454
     vsock_stream_connect+0x2b3/0xc70 net/vmw_vsock/af_vsock.c:1288
     __sys_connect_file+0x161/0x1c0 net/socket.c:1857
     __sys_connect+0x174/0x1b0 net/socket.c:1874
     __do_sys_connect net/socket.c:1885 [inline]
     __se_sys_connect net/socket.c:1882 [inline]
     __x64_sys_connect+0x73/0xb0 net/socket.c:1882
     do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
     entry_SYSCALL_64_after_hwframe+0x49/0xbe

To avoid this issue, this patch remove the lock acquiring in the
.release() callback of hyperv and virtio transports, and it holds
the lock when we call vsk->transport->release() in the vsock core.

Reported-by: syzbot+731710996d79d0d58fbc@syzkaller.appspotmail.com
Fixes: 408624af4c89 ("vsock: use local transport when it is loaded")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'rework-phylink-interface-for-split-MAC-PCS-support'

Russell King says:

====================
rework phylink interface for split MAC/PCS support

The following series changes the phylink interface to allow us to
better support split MAC / MAC PCS setups. The fundamental change
required for this turns out to be quite simple.

Today, mac_config() is used for everything to do with setting the
parameters for the MAC, and mac_link_up() is used to inform the
MAC driver that the link is now up (and so to allow packet flow.)
mac_config() also has had a few implementation issues, with folk
who believe that members such as "speed" and "duplex" are always
valid, where "link" gets used inappropriately, etc.

With the proposed patches, all this changes subtly - but in a
backwards compatible way at this stage.

We pass the the full resolved link state (speed, duplex, pause) to
mac_link_up(), and it is now guaranteed that these parameters to
this function will always be valid (no more SPEED_UNKNOWN or
DUPLEX_UNKNOWN here - unless phylink is fed with such things.)

Drivers should convert over to using the state in mac_link_up()
rather than configuring the speed, duplex and pause in the
mac_config() method. The patch series includes a number of MAC
drivers which I've thought have been easy targets - I've left the
remainder as I think they need maintainer input. However, *all*
drivers will need conversion for future phylink development.

v2: add ocelot/felix and qca/ar9331 DSA drivers to patch 2, add
received tested-by so far.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: mvpp2: use resolved link config in mac_link_up()

Convert the Marvell mvpp2 ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mvneta: use resolved link config in mac_link_up()

Convert the Marvell mvneta ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: macb: use resolved link config in mac_link_up()

Convert the macb ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().

Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dpaa2-mac: use resolved link config in mac_link_up()

Convert the DPAA2 ethernet driver to use the finalised link parameters
in mac_link_up() rather than the parameters in mac_config(), which are
more suited to the needs of the DPAA2 MC firmware than those available
via mac_config().

Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: use resolved link config in mac_link_up()

Convert the Xilinx AXI ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().

Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mv88e6xxx: use resolved link config in mac_link_up()

Use the resolved link configuration to set the MAC configuration when
mac_link_up() for non-internal-PHY ports.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: propagate resolved link config via mac_link_up()

Propagate the resolved link configuration down via DSA's
phylink_mac_link_up() operation to allow split PCS/MAC to work.

Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phylink: propagate resolved link config via mac_link_up()

Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.

Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

unix: It's CONFIG_PROC_FS not CONFIG_PROCFS

Fixes: 3a12500ed5dd ("unix: define and set show_fdinfo only if procfs is enabled")
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-rmnet-fix-several-bugs'

Taehee Yoo says:

====================
net: rmnet: fix several bugs

This patchset is to fix several bugs in RMNET module.

1. The first patch fixes NULL-ptr-deref in rmnet_newlink().
When rmnet interface is being created, it uses IFLA_LINK
without checking NULL.
So, if userspace doesn't set IFLA_LINK, panic will occur.
In this patch, checking NULL pointer code is added.

2. The second patch fixes NULL-ptr-deref in rmnet_changelink().
To get real device in rmnet_changelink(), it uses IFLA_LINK.
But, IFLA_LINK should not be used in rmnet_changelink().

3. The third patch fixes suspicious RCU usage in rmnet_get_port().
rmnet_get_port() uses rcu_dereference_rtnl().
But, rmnet_get_port() is used by datapath.
So, rcu_dereference_bh() should be used instead of rcu_dereference_rtnl().

4. The fourth patch fixes suspicious RCU usage in
rmnet_force_unassociate_device().
RCU critical section should not be scheduled.
But, unregister_netdevice_queue() in the rmnet_force_unassociate_device()
would be scheduled.
So, the RCU warning occurs.
In this patch, the rcu_read_lock() in the rmnet_force_unassociate_device()
is removed because it's unnecessary.

5. The fifth patch fixes duplicate MUX ID case.
RMNET MUX ID is unique.
So, rmnet interface isn't allowed to be created, which have
a duplicate MUX ID.
But, only rmnet_newlink() checks this condition, rmnet_changelink()
doesn't check this.
So, duplicate MUX ID case would happen.

6. The sixth patch fixes upper/lower interface relationship problems.
When IFLA_LINK is used, the upper/lower infrastructure should be used.
Because it checks the maximum depth of upper/lower interfaces and it also
checks circular interface relationship, etc.
In this patch, netdev_upper_dev_link() is used.

7. The seventh patch fixes bridge related problems.
a) ->ndo_del_slave() doesn't work.
b) It couldn't detect circular upper/lower interface relationship.
c) It couldn't prevent stack overflow because of too deep depth
of upper/lower interface
d) It doesn't check the number of lower interfaces.
e) Panics because of several reasons.
These problems are actually the same problem.
So, this patch fixes these problems.

8. The eighth patch fixes packet forwarding issue in bridge mode
Packet forwarding is not working in rmnet bridge mode.
Because when a packet is forwarded, skb_push() for an ethernet header
is needed. But it doesn't call skb_push().
So, the ethernet header will be lost.

Change log:
- update commit logs.
- drop two patches in this patchset because of wrong target branch.
   - ("net: rmnet: add missing module alias")
   - ("net: rmnet: print error message when command fails")
- remove unneessary rcu_read_lock() in the third patch.
- use rcu_dereference_bh() instead of rcu_dereference in third patch.
- do not allow to add a bridge device if rmnet interface is already
   bridge mode in the seventh patch.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: rmnet: fix packet forwarding in rmnet bridge mode

Packet forwarding is not working in rmnet bridge mode.
Because when a packet is forwarded, skb_push() for an ethernet header
is needed. But it doesn't call skb_push().
So, the ethernet header will be lost.

Test commands:
    modprobe rmnet
    ip netns add nst
    ip netns add nst2
    ip link add veth0 type veth peer name veth1
    ip link add veth2 type veth peer name veth3
    ip link set veth1 netns nst
    ip link set veth3 netns nst2

    ip link add rmnet0 link veth0 type rmnet mux_id 1
    ip link set veth2 master rmnet0
    ip link set veth0 up
    ip link set veth2 up
    ip link set rmnet0 up
    ip a a 192.168.100.1/24 dev rmnet0

    ip netns exec nst ip link set veth1 up
    ip netns exec nst ip a a 192.168.100.2/24 dev veth1
    ip netns exec nst2 ip link set veth3 up
    ip netns exec nst2 ip a a 192.168.100.3/24 dev veth3
    ip netns exec nst2 ping 192.168.100.2

Fixes: 60d58f971c10 ("net: qualcomm: rmnet: Implement bridge mode")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: rmnet: fix bridge mode bugs

In order to attach a bridge interface to the rmnet interface,
"master" operation is used.
(e.g. ip link set dummy1 master rmnet0)
But, in the rmnet_add_bridge(), which is a callback of ->ndo_add_slave()
doesn't register lower interface.
So, ->ndo_del_slave() doesn't work.
There are other problems too.
1. It couldn't detect circular upper/lower interface relationship.
2. It couldn't prevent stack overflow because of too deep depth
of upper/lower interface
3. It doesn't check the number of lower interfaces.
4. Panics because of several reasons.

The root problem of these issues is actually the same.
So, in this patch, these all problems will be fixed.

Test commands:
    modprobe rmnet
    ip link add dummy0 type dummy
    ip link add rmnet0 link dummy0 type rmnet mux_id 1
    ip link add dummy1 master rmnet0 type dummy
    ip link add dummy2 master rmnet0 type dummy
    ip link del rmnet0
    ip link del dummy2
    ip link del dummy1

Splat looks like:
[   41.867595][ T1164] general protection fault, probably for non-canonical address 0xdffffc0000000101I
[   41.869993][ T1164] KASAN: null-ptr-deref in range [0x0000000000000808-0x000000000000080f]
[   41.872950][ T1164] CPU: 0 PID: 1164 Comm: ip Not tainted 5.6.0-rc1+ #447
[   41.873915][ T1164] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   41.875161][ T1164] RIP: 0010:rmnet_unregister_bridge.isra.6+0x71/0xf0 [rmnet]
[   41.876178][ T1164] Code: 48 89 ef 48 89 c6 5b 5d e9 fc fe ff ff e8 f7 f3 ff ff 48 8d b8 08 08 00 00 48 ba 00 7
[   41.878925][ T1164] RSP: 0018:ffff8880c4d0f188 EFLAGS: 00010202
[   41.879774][ T1164] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000101
[   41.887689][ T1164] RDX: dffffc0000000000 RSI: ffffffffb8cf64f0 RDI: 0000000000000808
[   41.888727][ T1164] RBP: ffff8880c40e4000 R08: ffffed101b3c0e3c R09: 0000000000000001
[   41.889749][ T1164] R10: 0000000000000001 R11: ffffed101b3c0e3b R12: 1ffff110189a1e3c
[   41.890783][ T1164] R13: ffff8880c4d0f200 R14: ffffffffb8d56160 R15: ffff8880ccc2c000
[   41.891794][ T1164] FS:  00007f4300edc0c0(0000) GS:ffff8880d9c00000(0000) knlGS:0000000000000000
[   41.892953][ T1164] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   41.893800][ T1164] CR2: 00007f43003bc8c0 CR3: 00000000ca53e001 CR4: 00000000000606f0
[   41.894824][ T1164] Call Trace:
[   41.895274][ T1164]  ? rcu_is_watching+0x2c/0x80
[   41.895895][ T1164]  rmnet_config_notify_cb+0x1f7/0x590 [rmnet]
[   41.896687][ T1164]  ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet]
[   41.897611][ T1164]  ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet]
[   41.898508][ T1164]  ? __module_text_address+0x13/0x140
[   41.899162][ T1164]  notifier_call_chain+0x90/0x160
[   41.899814][ T1164]  rollback_registered_many+0x660/0xcf0
[   41.900544][ T1164]  ? netif_set_real_num_tx_queues+0x780/0x780
[   41.901316][ T1164]  ? __lock_acquire+0xdfe/0x3de0
[   41.901958][ T1164]  ? memset+0x1f/0x40
[   41.902468][ T1164]  ? __nla_validate_parse+0x98/0x1ab0
[   41.903166][ T1164]  unregister_netdevice_many.part.133+0x13/0x1b0
[   41.903988][ T1164]  rtnl_delete_link+0xbc/0x100
[ ... ]

Fixes: 60d58f971c10 ("net: qualcomm: rmnet: Implement bridge mode")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: rmnet: use upper/lower device infrastructure

netdev_upper_dev_link() is useful to manage lower/upper interfaces.
And this function internally validates looping, maximum depth.
All or most virtual interfaces that could have a real interface
(e.g. macsec, macvlan, ipvlan etc.) use lower/upper infrastructure.

Test commands:
    modprobe rmnet
    ip link add dummy0 type dummy
    ip link add rmnet1 link dummy0 type rmnet mux_id 1
    for i in {2..100}
    do
        let A=$i-1
        ip link add rmnet$i link rmnet$A type rmnet mux_id $i
    done
    ip link del dummy0

The purpose of the test commands is to make stack overflow.

Splat looks like:
[   52.411438][ T1395] BUG: KASAN: slab-out-of-bounds in find_busiest_group+0x27e/0x2c00
[   52.413218][ T1395] Write of size 64 at addr ffff8880c774bde0 by task ip/1395
[   52.414841][ T1395]
[   52.430720][ T1395] CPU: 1 PID: 1395 Comm: ip Not tainted 5.6.0-rc1+ #447
[   52.496511][ T1395] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   52.513597][ T1395] Call Trace:
[   52.546516][ T1395]
[   52.558773][ T1395] Allocated by task 3171537984:
[   52.588290][ T1395] BUG: unable to handle page fault for address: ffffffffb999e260
[   52.589311][ T1395] #PF: supervisor read access in kernel mode
[   52.590529][ T1395] #PF: error_code(0x0000) - not-present page
[   52.591374][ T1395] PGD d6818067 P4D d6818067 PUD d6819063 PMD 0
[   52.592288][ T1395] Thread overran stack, or stack corrupted
[   52.604980][ T1395] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[   52.605856][ T1395] CPU: 1 PID: 1395 Comm: ip Not tainted 5.6.0-rc1+ #447
[   52.611764][ T1395] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   52.621520][ T1395] RIP: 0010:stack_depot_fetch+0x10/0x30
[   52.622296][ T1395] Code: ff e9 f9 fe ff ff 48 89 df e8 9c 1d 91 ff e9 ca fe ff ff cc cc cc cc cc cc cc 89 f8 0
[   52.627887][ T1395] RSP: 0018:ffff8880c774bb60 EFLAGS: 00010006
[   52.628735][ T1395] RAX: 00000000001f8880 RBX: ffff8880c774d140 RCX: 0000000000000000
[   52.631773][ T1395] RDX: 000000000000001d RSI: ffff8880c774bb68 RDI: 0000000000003ff0
[   52.649584][ T1395] RBP: ffffea00031dd200 R08: ffffed101b43e403 R09: ffffed101b43e403
[   52.674857][ T1395] R10: 0000000000000001 R11: ffffed101b43e402 R12: ffff8880d900e5c0
[   52.678257][ T1395] R13: ffff8880c774c000 R14: 0000000000000000 R15: dffffc0000000000
[   52.694541][ T1395] FS:  00007fe867f6e0c0(0000) GS:ffff8880da000000(0000) knlGS:0000000000000000
[   52.764039][ T1395] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   52.815008][ T1395] CR2: ffffffffb999e260 CR3: 00000000c26aa005 CR4: 00000000000606e0
[   52.862312][ T1395] Call Trace:
[   52.887133][ T1395] Modules linked in: dummy rmnet veth openvswitch nsh nf_conncount nf_nat nf_conntrack nf_dex
[   52.936749][ T1395] CR2: ffffffffb999e260
[   52.965695][ T1395] ---[ end trace 7e32ca99482dbb31 ]---
[   52.966556][ T1395] RIP: 0010:stack_depot_fetch+0x10/0x30
[   52.971083][ T1395] Code: ff e9 f9 fe ff ff 48 89 df e8 9c 1d 91 ff e9 ca fe ff ff cc cc cc cc cc cc cc 89 f8 0
[   53.003650][ T1395] RSP: 0018:ffff8880c774bb60 EFLAGS: 00010006
[   53.043183][ T1395] RAX: 00000000001f8880 RBX: ffff8880c774d140 RCX: 0000000000000000
[   53.076480][ T1395] RDX: 000000000000001d RSI: ffff8880c774bb68 RDI: 0000000000003ff0
[   53.093858][ T1395] RBP: ffffea00031dd200 R08: ffffed101b43e403 R09: ffffed101b43e403
[   53.112795][ T1395] R10: 0000000000000001 R11: ffffed101b43e402 R12: ffff8880d900e5c0
[   53.139837][ T1395] R13: ffff8880c774c000 R14: 0000000000000000 R15: dffffc0000000000
[   53.141500][ T1395] FS:  00007fe867f6e0c0(0000) GS:ffff8880da000000(0000) knlGS:0000000000000000
[   53.143343][ T1395] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   53.152007][ T1395] CR2: ffffffffb999e260 CR3: 00000000c26aa005 CR4: 00000000000606e0
[   53.156459][ T1395] Kernel panic - not syncing: Fatal exception
[   54.213570][ T1395] Shutting down cpus with NMI
[   54.354112][ T1395] Kernel Offset: 0x33000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0x)
[   54.355687][ T1395] Rebooting in 5 seconds..

Fixes: b37f78f234bf ("net: qualcomm: rmnet: Fix crash on real dev unregistration")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: rmnet: do not allow to change mux id if mux id is duplicated

Basically, duplicate mux id isn't be allowed.
So, the creation of rmnet will be failed if there is duplicate mux id
is existing.
But, changelink routine doesn't check duplicate mux id.

Test commands:
    modprobe rmnet
    ip link add dummy0 type dummy
    ip link add rmnet0 link dummy0 type rmnet mux_id 1
    ip link add rmnet1 link dummy0 type rmnet mux_id 2
    ip link set rmnet1 type rmnet mux_id 1

Fixes: 23790ef12082 ("net: qualcomm: rmnet: Allow to configure flags for existing devices")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: rmnet: remove rcu_read_lock in rmnet_force_unassociate_device()

The notifier_call() of the slave interface removes rmnet interface with
unregister_netdevice_queue().
But, before calling unregister_netdevice_queue(), it acquires
rcu readlock.
In the RCU critical section, sleeping isn't be allowed.
But, unregister_netdevice_queue() internally calls synchronize_net(),
which would sleep.
So, suspicious RCU usage warning occurs.

Test commands:
    modprobe rmnet
    ip link add dummy0 type dummy
    ip link add dummy1 type dummy
    ip link add rmnet0 link dummy0 type rmnet mux_id 1
    ip link set dummy1 master rmnet0
    ip link del dummy0

Splat looks like:
[   79.639245][ T1195] =============================
[   79.640134][ T1195] WARNING: suspicious RCU usage
[   79.640852][ T1195] 5.6.0-rc1+ #447 Not tainted
[   79.641657][ T1195] -----------------------------
[   79.642472][ T1195] ./include/linux/rcupdate.h:273 Illegal context switch in RCU read-side critical section!
[   79.644043][ T1195]
[   79.644043][ T1195] other info that might help us debug this:
[   79.644043][ T1195]
[   79.645682][ T1195]
[   79.645682][ T1195] rcu_scheduler_active = 2, debug_locks = 1
[   79.646980][ T1195] 2 locks held by ip/1195:
[   79.647629][ T1195]  #0: ffffffffa3cf64f0 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x457/0x890
[   79.649312][ T1195]  #1: ffffffffa39256c0 (rcu_read_lock){....}, at: rmnet_config_notify_cb+0xf0/0x590 [rmnet]
[   79.651717][ T1195]
[   79.651717][ T1195] stack backtrace:
[   79.652650][ T1195] CPU: 3 PID: 1195 Comm: ip Not tainted 5.6.0-rc1+ #447
[   79.653702][ T1195] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   79.655037][ T1195] Call Trace:
[   79.655560][ T1195]  dump_stack+0x96/0xdb
[   79.656252][ T1195]  ___might_sleep+0x345/0x440
[   79.656994][ T1195]  synchronize_net+0x18/0x30
[   79.661132][ T1195]  netdev_rx_handler_unregister+0x40/0xb0
[   79.666266][ T1195]  rmnet_unregister_real_device+0x42/0xb0 [rmnet]
[   79.667211][ T1195]  rmnet_config_notify_cb+0x1f7/0x590 [rmnet]
[   79.668121][ T1195]  ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet]
[   79.669166][ T1195]  ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet]
[   79.670286][ T1195]  ? __module_text_address+0x13/0x140
[   79.671139][ T1195]  notifier_call_chain+0x90/0x160
[   79.671973][ T1195]  rollback_registered_many+0x660/0xcf0
[   79.672893][ T1195]  ? netif_set_real_num_tx_queues+0x780/0x780
[   79.675091][ T1195]  ? __lock_acquire+0xdfe/0x3de0
[   79.675825][ T1195]  ? memset+0x1f/0x40
[   79.676367][ T1195]  ? __nla_validate_parse+0x98/0x1ab0
[   79.677290][ T1195]  unregister_netdevice_many.part.133+0x13/0x1b0
[   79.678163][ T1195]  rtnl_delete_link+0xbc/0x100
[ ... ]

Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: rmnet: fix suspicious RCU usage

rmnet_get_port() internally calls rcu_dereference_rtnl(),
which checks RTNL.
But rmnet_get_port() could be called by packet path.
The packet path is not protected by RTNL.
So, the suspicious RCU usage problem occurs.

Test commands:
    modprobe rmnet
    ip netns add nst
    ip link add veth0 type veth peer name veth1
    ip link set veth1 netns nst
    ip link add rmnet0 link veth0 type rmnet mux_id 1
    ip netns exec nst ip link add rmnet1 link veth1 type rmnet mux_id 1
    ip netns exec nst ip link set veth1 up
    ip netns exec nst ip link set rmnet1 up
    ip netns exec nst ip a a 192.168.100.2/24 dev rmnet1
    ip link set veth0 up
    ip link set rmnet0 up
    ip a a 192.168.100.1/24 dev rmnet0
    ping 192.168.100.2

Splat looks like:
[  146.630958][ T1174] WARNING: suspicious RCU usage
[  146.631735][ T1174] 5.6.0-rc1+ #447 Not tainted
[  146.632387][ T1174] -----------------------------
[  146.633151][ T1174] drivers/net/ethernet/qualcomm/rmnet/rmnet_config.c:386 suspicious rcu_dereference_check() !
[  146.634742][ T1174]
[  146.634742][ T1174] other info that might help us debug this:
[  146.634742][ T1174]
[  146.645992][ T1174]
[  146.645992][ T1174] rcu_scheduler_active = 2, debug_locks = 1
[  146.646937][ T1174] 5 locks held by ping/1174:
[  146.647609][ T1174]  #0: ffff8880c31dea70 (sk_lock-AF_INET){+.+.}, at: raw_sendmsg+0xab8/0x2980
[  146.662463][ T1174]  #1: ffffffff93925660 (rcu_read_lock_bh){....}, at: ip_finish_output2+0x243/0x2150
[  146.671696][ T1174]  #2: ffffffff93925660 (rcu_read_lock_bh){....}, at: __dev_queue_xmit+0x213/0x2940
[  146.673064][ T1174]  #3: ffff8880c19ecd58 (&dev->qdisc_running_key#7){+...}, at: ip_finish_output2+0x714/0x2150
[  146.690358][ T1174]  #4: ffff8880c5796898 (&dev->qdisc_xmit_lock_key#3){+.-.}, at: sch_direct_xmit+0x1e2/0x1020
[  146.699875][ T1174]
[  146.699875][ T1174] stack backtrace:
[  146.701091][ T1174] CPU: 0 PID: 1174 Comm: ping Not tainted 5.6.0-rc1+ #447
[  146.705215][ T1174] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[  146.706565][ T1174] Call Trace:
[  146.707102][ T1174]  dump_stack+0x96/0xdb
[  146.708007][ T1174]  rmnet_get_port.part.9+0x76/0x80 [rmnet]
[  146.709233][ T1174]  rmnet_egress_handler+0x107/0x420 [rmnet]
[  146.710492][ T1174]  ? sch_direct_xmit+0x1e2/0x1020
[  146.716193][ T1174]  rmnet_vnd_start_xmit+0x3d/0xa0 [rmnet]
[  146.717012][ T1174]  dev_hard_start_xmit+0x160/0x740
[  146.717854][ T1174]  sch_direct_xmit+0x265/0x1020
[  146.718577][ T1174]  ? register_lock_class+0x14d0/0x14d0
[  146.719429][ T1174]  ? dev_watchdog+0xac0/0xac0
[  146.723738][ T1174]  ? __dev_queue_xmit+0x15fd/0x2940
[  146.724469][ T1174]  ? lock_acquire+0x164/0x3b0
[  146.725172][ T1174]  __dev_queue_xmit+0x20c7/0x2940
[ ... ]

Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: rmnet: fix NULL pointer dereference in rmnet_changelink()

In the rmnet_changelink(), it uses IFLA_LINK without checking
NULL pointer.
tb[IFLA_LINK] could be NULL pointer.
So, NULL-ptr-deref could occur.

rmnet already has a lower interface (real_dev).
So, after this patch, rmnet_changelink() does not use IFLA_LINK anymore.

Test commands:
    modprobe rmnet
    ip link add dummy0 type dummy
    ip link add rmnet0 link dummy0 type rmnet mux_id 1
    ip link set rmnet0 type rmnet mux_id 2

Splat looks like:
[   90.578726][ T1131] general protection fault, probably for non-canonical address 0xdffffc0000000000I
[   90.581121][ T1131] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
[   90.582380][ T1131] CPU: 2 PID: 1131 Comm: ip Not tainted 5.6.0-rc1+ #447
[   90.584285][ T1131] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   90.587506][ T1131] RIP: 0010:rmnet_changelink+0x5a/0x8a0 [rmnet]
[   90.588546][ T1131] Code: 83 ec 20 48 c1 ea 03 80 3c 02 00 0f 85 6f 07 00 00 48 8b 5e 28 48 b8 00 00 00 00 00 0
[   90.591447][ T1131] RSP: 0018:ffff8880ce78f1b8 EFLAGS: 00010247
[   90.592329][ T1131] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffff8880ce78f8b0
[   90.593253][ T1131] RDX: 0000000000000000 RSI: ffff8880ce78f4a0 RDI: 0000000000000004
[   90.594058][ T1131] RBP: ffff8880cf543e00 R08: 0000000000000002 R09: 0000000000000002
[   90.594859][ T1131] R10: ffffffffc0586a40 R11: 0000000000000000 R12: ffff8880ca47c000
[   90.595690][ T1131] R13: ffff8880ca47c000 R14: ffff8880cf545000 R15: 0000000000000000
[   90.596553][ T1131] FS:  00007f21f6c7e0c0(0000) GS:ffff8880da400000(0000) knlGS:0000000000000000
[   90.597504][ T1131] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   90.599418][ T1131] CR2: 0000556e413db458 CR3: 00000000c917a002 CR4: 00000000000606e0
[   90.600289][ T1131] Call Trace:
[   90.600631][ T1131]  __rtnl_newlink+0x922/0x1270
[   90.601194][ T1131]  ? lock_downgrade+0x6e0/0x6e0
[   90.601724][ T1131]  ? rtnl_link_unregister+0x220/0x220
[   90.602309][ T1131]  ? lock_acquire+0x164/0x3b0
[   90.602784][ T1131]  ? is_bpf_image_address+0xff/0x1d0
[   90.603331][ T1131]  ? rtnl_newlink+0x4c/0x90
[   90.603810][ T1131]  ? kernel_text_address+0x111/0x140
[   90.604419][ T1131]  ? __kernel_text_address+0xe/0x30
[   90.604981][ T1131]  ? unwind_get_return_address+0x5f/0xa0
[   90.605616][ T1131]  ? create_prof_cpu_mask+0x20/0x20
[   90.606304][ T1131]  ? arch_stack_walk+0x83/0xb0
[   90.606985][ T1131]  ? stack_trace_save+0x82/0xb0
[   90.607656][ T1131]  ? stack_trace_consume_entry+0x160/0x160
[   90.608503][ T1131]  ? deactivate_slab.isra.78+0x2c5/0x800
[   90.609336][ T1131]  ? kasan_unpoison_shadow+0x30/0x40
[   90.610096][ T1131]  ? kmem_cache_alloc_trace+0x135/0x350
[   90.610889][ T1131]  ? rtnl_newlink+0x4c/0x90
[   90.611512][ T1131]  rtnl_newlink+0x65/0x90
[ ... ]

Fixes: 23790ef12082 ("net: qualcomm: rmnet: Allow to configure flags for existing devices")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: rmnet: fix NULL pointer dereference in rmnet_newlink()

rmnet registers IFLA_LINK interface as a lower interface.
But, IFLA_LINK could be NULL.
In the current code, rmnet doesn't check IFLA_LINK.
So, panic would occur.

Test commands:
    modprobe rmnet
    ip link add rmnet0 type rmnet mux_id 1

Splat looks like:
[   36.826109][ T1115] general protection fault, probably for non-canonical address 0xdffffc0000000000I
[   36.838817][ T1115] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
[   36.839908][ T1115] CPU: 1 PID: 1115 Comm: ip Not tainted 5.6.0-rc1+ #447
[   36.840569][ T1115] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   36.841408][ T1115] RIP: 0010:rmnet_newlink+0x54/0x510 [rmnet]
[   36.841986][ T1115] Code: 83 ec 18 48 c1 e9 03 80 3c 01 00 0f 85 d4 03 00 00 48 8b 6a 28 48 b8 00 00 00 00 00 c
[   36.843923][ T1115] RSP: 0018:ffff8880b7e0f1c0 EFLAGS: 00010247
[   36.844756][ T1115] RAX: dffffc0000000000 RBX: ffff8880d14cca00 RCX: 1ffff11016fc1e99
[   36.845859][ T1115] RDX: 0000000000000000 RSI: ffff8880c3d04000 RDI: 0000000000000004
[   36.846961][ T1115] RBP: 0000000000000000 R08: ffff8880b7e0f8b0 R09: ffff8880b6ac2d90
[   36.848020][ T1115] R10: ffffffffc0589a40 R11: ffffed1016d585b7 R12: ffffffff88ceaf80
[   36.848788][ T1115] R13: ffff8880c3d04000 R14: ffff8880b7e0f8b0 R15: ffff8880c3d04000
[   36.849546][ T1115] FS:  00007f50ab3360c0(0000) GS:ffff8880da000000(0000) knlGS:0000000000000000
[   36.851784][ T1115] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   36.852422][ T1115] CR2: 000055871afe5ab0 CR3: 00000000ae246001 CR4: 00000000000606e0
[   36.853181][ T1115] Call Trace:
[   36.853514][ T1115]  __rtnl_newlink+0xbdb/0x1270
[   36.853967][ T1115]  ? lock_downgrade+0x6e0/0x6e0
[   36.854420][ T1115]  ? rtnl_link_unregister+0x220/0x220
[   36.854936][ T1115]  ? lock_acquire+0x164/0x3b0
[   36.855376][ T1115]  ? is_bpf_image_address+0xff/0x1d0
[   36.855884][ T1115]  ? rtnl_newlink+0x4c/0x90
[   36.856304][ T1115]  ? kernel_text_address+0x111/0x140
[   36.856857][ T1115]  ? __kernel_text_address+0xe/0x30
[   36.857440][ T1115]  ? unwind_get_return_address+0x5f/0xa0
[   36.858063][ T1115]  ? create_prof_cpu_mask+0x20/0x20
[   36.858644][ T1115]  ? arch_stack_walk+0x83/0xb0
[   36.859171][ T1115]  ? stack_trace_save+0x82/0xb0
[   36.859710][ T1115]  ? stack_trace_consume_entry+0x160/0x160
[   36.860357][ T1115]  ? deactivate_slab.isra.78+0x2c5/0x800
[   36.860928][ T1115]  ? kasan_unpoison_shadow+0x30/0x40
[   36.861520][ T1115]  ? kmem_cache_alloc_trace+0x135/0x350
[   36.862125][ T1115]  ? rtnl_newlink+0x4c/0x90
[   36.864073][ T1115]  rtnl_newlink+0x65/0x90
[ ... ]

Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa2-eth: add support for nway reset

Add support for ethtool -r so that PHY negotiation can be restarted.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa2-eth: add support for mii ioctls

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'kbuild-fixes-v5.6-2' of git://git./linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

- fix missed rebuild of DT schema check

- add some phony targets to PHONY

- fix comments and documents

* tag 'kbuild-fixes-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: get rid of trailing slash from subdir- example
  kbuild: add dt_binding_check to PHONY in a correct place
  kbuild: add dtbs_check to PHONY
  kbuild: remove unneeded semicolon at the end of cmd_dtb_check
  kbuild: fix DT binding schema rule to detect command line changes
  kbuild: remove wrong documentation about mandatory-y
  kbuild: add comment for V=2 mode

net: phy: marvell10g: read copper results from CSSR1

Read the copper autonegotiation results from the copper specific
status register, rather than decoding the advertisements. Reading
what the link is actually doing will allow us to support downshift
modes.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: marvell: don't interpret PHY status unless resolved

Don't attempt to interpret the PHY specific status register unless
the PHY is indicating that the resolution is valid.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx5: register lag notifier for init network namespace only

The current code causes problems when the unregistering netdevice could
be different then the registering one.

Since the check in mlx5_lag_netdev_event() does not allow any other
network namespace anyway, fix this by registerting the lag notifier
per init network namespace only.

Fixes: d48834f9d4b4 ("mlx5: Use dev_net netdevice notifier registrations")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Aya Levin <ayal@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 's390-qeth-next'

Julian Wiedmann says:

====================
s390/qeth: updates 2020-02-27

please apply the following patch series for qeth to netdev's net-next
tree.

This adds support for ETHTOOL_RX_COPYBREAK, along with small cleanups
and fine-tuning.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: support configurable RX copybreak

Implement the ethtool hooks for the ETHTOOL_RX_COPYBREAK tunable.

The copybreak is stored into netdev_priv, so that we automatically go
back to the default value if the netdev is re-allocated.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: don't check for IFF_UP when scheduling napi

Trust the napi_disable() in qeth_stop() to handle this.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: don't re-start read cmd when IDX has terminated

Once the IDX connection is down, there's no point in trying to issue
more IOs.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: reset seqnos on connection startup

This let's us start every new IDX connection with clean seqnos.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: remove unused cmd definitions

Looks like these were never used, ever since the driver was initially
added.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: validate device-provided MAC address

It's good practice to not blindly trust what the HW offers.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: clean up CREATE_ADDR cmd code

Properly define the cmd's struct to get rid of some casts and accesses
at magic offsets.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: remove dead code in qeth_l3_iqd_read_initial_mac()

card->info.unique_id is always 0 for IQD devices, so don't bother with
copying it into the 0-initialized cmd.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-linus' of git://git./linux/kernel/git/hid/hid

Pull HID subsystem fixes from Jiri Kosina:

- syzkaller-reported error handling fixes in various drivers, from
   various people

- increase of HID report buffer size to 8K, which is apparently needed
   by certain modern devices

- a few new device-ID-specific fixes / quirks

- battery charging status reporting fix in logitech-hidpp, from Filipe
   Laíns

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
  HID: hid-bigbenff: fix race condition for scheduled work during removal
  HID: hid-bigbenff: call hid_hw_stop() in case of error
  HID: hid-bigbenff: fix general protection fault caused by double kfree
  HID: i2c-hid: add Trekstor Surfbook E11B to descriptor override
  HID: alps: Fix an error handling path in 'alps_input_configured()'
  HID: hiddev: Fix race in in hiddev_disconnect()
  HID: core: increase HID report buffer size to 8KiB
  HID: core: fix off-by-one memset in hid_report_raw_event()
  HID: apple: Add support for recent firmware on Magic Keyboards
  HID: ite: Only bind to keyboard USB interface on Acer SW5-012 keyboard dock
  HID: logitech-hidpp: BatteryVoltage: only read chargeStatus if extPower is active

unix: define and set show_fdinfo only if procfs is enabled

Follow the pattern used with other *_show_fdinfo functions and only
define unix_show_fdinfo and set it in proto_ops if CONFIG_PROCFS
is set.

Fixes: 3c32da19a858 ("unix: Show number of pending scm files of receive queue in fdinfo")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'selftests-updates-for-mlxsw-driver-test'

Jiri Pirko says:

====================
selftests: updates for mlxsw driver test

This patchset contains tweaks to the existing tests and is also adding
couple of new ones, namely tests for shared buffer and red offload.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: resource_scale: Invoke for Spectrum-3

The scale test for Spectrum-2 should be invoked for Spectrum-2 and
Spectrum-3. Add the appropriate device ID.

Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: Reduce router scale running time using offload indication

Currently, the test inserts X /32 routes and for each route it is
testing that a packet sent from the first host is received by the second
host, which is very time-consuming.

Instead only validate the offload flag of each route and get the same result.

Wait between the creation of the routes and the offload validation in
order to make sure that all the routes were successfully offloaded.

Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: Reduce running time using offload indication

After adding a given number of flower rules for different IPv6
addresses, the test generates traffic and ensures that each packet is
received, which is time-consuming.

Instead, test the offload indication of the tc flower rules and reduce
the running time by half.

Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: Add shared buffer traffic test

Test the max shared buffer occupancy for port's pool and port's TC's (using
different types of packets).

Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: Add mlxsw lib

Add mlxsw lib for common defines, helpers etc.

Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: devlink_lib: Add devlink port helpers

Add two devlink port helpers:
* devlink port get by netdev
* devlink cpu port get

Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: devlink_lib: Check devlink info command is supported

Sanity check for devlink info command.

Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: Add shared buffer configuration test

Test physical ports' shared buffer configuration options using random
values related to a specific configuration option. There are 3
configuration options: pool, TC bind and portpool.

Each sub-test, test a different configuration option and random the related
values as the follow:
* For pools, pool's size will be randomized.
* For TC bind, pool number and threshold will be randomized.
* For portpools, threshold will be randomized.

Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: Use busywait helper in rtnetlink test

Rtnetlink test uses offload indication checks.

Use a busywait helper and wait until the offload indication is set or
fail if it reaches timeout.

Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>