OSDN Git Service
Nicholas Kazlauskas [Mon, 3 Jun 2019 17:44:37 +0000 (13:44 -0400)]
drm/amd/display: Add connector debugfs for "output_bpc"
[Why]
This will be useful for verifying whether we enter the correct output
color depth from IGT.
[How]
Locks the connector and associated CRTC if available and outputs
the current and maximum output bpc values.
Example:
cat /sys/kernel/debug/dri/0/DP-1/output_bpc
Current: 8
Maximum: 10
v2: Drop unneeded connector status check
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Prike Liang [Mon, 27 May 2019 08:05:50 +0000 (16:05 +0800)]
drm/amd/amdgpu: add RLC firmware to support raven1 refresh
Use SMU firmware version to indentify the raven1 refresh device and
then load homologous RLC FW.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Suggested-by: Huang Rui<Ray.Huang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Chengming Gui [Mon, 13 May 2019 09:41:19 +0000 (17:41 +0800)]
drm/amd/powerplay: add set_power_profile_mode for raven1_refresh
add gfxoff_state_changed_by_workload to control gfxoff
when set power_profile_mode
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Trigger Huang [Mon, 3 Jun 2019 08:48:17 +0000 (16:48 +0800)]
drm/amdgpu: Hardcode reg access using L1 security
Under Vega10 SR-IOV VF, L1 register access mode should be enabled by
default as the non-security VF will no longer be supported.
Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Shirish S [Tue, 4 Jun 2019 15:55:03 +0000 (21:25 +0530)]
drm/amdgpu/{uvd,vcn}: fetch ring's read_ptr after alloc
[What]
readptr read always returns zero, since most likely
these blocks are either power or clock gated.
[How]
fetch rptr after amdgpu_ring_alloc() which informs
the power management code that the block is about to be
used and hence the gating is turned off.
Signed-off-by: Louis Li <Ching-shih.Li@amd.com>
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Louis Li [Fri, 24 May 2019 22:39:47 +0000 (06:39 +0800)]
drm/amdgpu: fix ring test failure issue during s3 in vce 3.0 (V2)
[What]
vce ring test fails consistently during resume in s3 cycle, due to
mismatch read & write pointers.
On debug/analysis its found that rptr to be compared is not being
correctly updated/read, which leads to this failure.
Below is the failure signature:
[drm:amdgpu_vce_ring_test_ring] *ERROR* amdgpu: ring 12 test failed
[drm:amdgpu_device_ip_resume_phase2] *ERROR* resume of IP block <vce_v3_0> failed -110
[drm:amdgpu_device_resume] *ERROR* amdgpu_device_ip_resume failed (-110).
[How]
fetch rptr appropriately, meaning move its read location further down
in the code flow.
With this patch applied the s3 failure is no more seen for >5k s3 cycles,
which otherwise is pretty consistent.
V2: remove reduntant fetch of rptr
Signed-off-by: Louis Li <Ching-shih.Li@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jay Cornwall [Tue, 19 Jun 2018 15:17:30 +0000 (10:17 -0500)]
drm/amdkfd: Implement queue priority controls for gfx9
Ported from gfx8, no changes in register setup.
Signed-off-by: Jay Cornwall <Jay.Cornwall@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Oak Zeng [Tue, 7 Feb 2017 21:40:14 +0000 (15:40 -0600)]
drm/amdkfd: CP queue priority controls
Translate queue priority into pipe priority and write to MQDs.
The priority values are used to perform queue and pipe arbitration.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Felix Kuehling [Wed, 1 May 2019 22:20:13 +0000 (18:20 -0400)]
drm/amdkfd: Simplify eviction state logic
Always mark evicted queues with q->properties.is_evicted = true, even
queues that are inactive for other reason. This simplifies maintaining
the eviction state as it doesn't require updating is_evicted when other
queue activation conditions change.
On the other hand, we now need to check those other queue activation
conditions whenever an evicted queues is restored. To minimize code
duplication, move the queue activation check into a macro so it can be
maintained in one central place.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Philip Cox <Philip.Cox@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
James Zhu [Tue, 4 Jun 2019 16:49:02 +0000 (12:49 -0400)]
drm/amdgpu: Fixed missing to clear some EDC count
EDC counts are related to instance and se. They are not the same
for different type of EDC. EDC clearing are changed to base on
individual EDC's instance and SE number.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nicholas Kazlauskas [Fri, 31 May 2019 16:05:26 +0000 (12:05 -0400)]
drm/amd/display: Add back missing hw translate init for DCN1_01
[Why]
DCN_VERSION_1_01 is no longer handled in the dal_hw_translate_init
switch since it was inadvertently dropped in the patch that removed the
unnecessary DCN1_01 guards.
This caused numerous regressions on DCN1_01 when loading the driver.
[How]
Add it back.
Fixes:
97df424fe7a7 ("drm/amd/display: Drop DCN1_01 guards")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nicholas Kazlauskas [Tue, 11 Jun 2019 16:54:05 +0000 (11:54 -0500)]
drm/amd/display: Don't set mode_changed=false if the stream was removed
[Why]
When switching from vt to desktop with EDID emulation we can receive
an atomic commit such that we have a crtc where mode_changed = true.
During the dm_update_crtc_state disable pass we remove the stream from
the context and free it on the dm_new_crtc_state.
During the enable pass we compare the new provisional stream to the
dm_old_crtc_state->stream and determine that the stream is unchanged
and no scaling has been changed.
Following this, new_crtc_state->mode_changed is then set to false.
The connectors haven't changed and the CRTC active state hasn't changed
so drm_atomic_crtc_needs_modeset returns false, so we jump to
skip_modeset and we hit:
BUG_ON(dm_new_crtc_state->stream == NULL);
...since the old stream is gone from the context and the new stream is
also still NULL.
[How]
Ensure that we still a stream to reuse before checking if we can reuse
the old stream without a full modeset.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Fri, 10 May 2019 14:09:48 +0000 (16:09 +0200)]
drm/amdgpu: stop removing BOs from the LRU v3
This avoids OOM situations when we have lots of threads
submitting at the same time.
v3: apply this to the whole driver, not just CS
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 16 May 2019 08:25:35 +0000 (10:25 +0200)]
drm/amdgpu: create GDS, GWS and OA in system domain
And only move them in on validation. This allows for better control
when multiple processes are fighting over those resources.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Fri, 17 May 2019 07:31:44 +0000 (09:31 +0200)]
drm/amdgpu: drop some validation failure messages
The messages about amdgpu_cs_list_validate are duplicated because the
caller will complain into the logs as well and we can also get
interrupted by a signal here.
Also fix the the caller to not report -EAGAIN from validation.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Fri, 31 May 2019 14:53:38 +0000 (22:53 +0800)]
drm/amdgpu/psp: udpate ta_ras interface header
ras ta interface header need to be updated to match with latest ta fw updates
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Daniel Vetter [Tue, 11 Jun 2019 11:29:33 +0000 (13:29 +0200)]
Merge tag 'omapdrm-5.3' of git://git./linux/kernel/git/tomba/linux into drm-next
omapdrm changes for 5.3
- Add support for DSI command mode displays
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a709f57d-6909-8550-3932-d84e0b5bc3ef@ti.com
Daniel Vetter [Tue, 11 Jun 2019 08:08:48 +0000 (10:08 +0200)]
Merge tag 'du-next-
20190608-2' of git://linuxtv.org/pinchartl/media into drm-next
R-Car DU changes for v5.3:
- R8A774A1 SoC support
- LVDS dual-link mode support
- Support for additional formats
- Misc fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190608134652.GE4786@pendragon.ideasonboard.com
Sebastian Reichel [Thu, 23 May 2019 20:07:56 +0000 (22:07 +0200)]
drm/omap: add support for manually updated displays
This adds the required infrastructure for manually updated displays,
such as DSI command mode panels. While those panels often support
partial updates we currently always do a full refresh.
The display will be refreshed when something calls the dirty callback,
such as libdrm's drmModeDirtyFB(). This is currently being done at least
by the kernel console and Xorg (with modesetting driver) in their
default configuration. Weston does not implement this and the fbdev
backend does not work (display will not update). Weston's DRM backend
uses double buffering and the page flip will also trigger a display
refresh.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Sebastian Reichel [Thu, 23 May 2019 20:07:55 +0000 (22:07 +0200)]
drm/omap: add framedone interrupt support
This prepares framedone interrupt handling for
manual display update support.
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Sebastian Reichel [Thu, 23 May 2019 20:07:54 +0000 (22:07 +0200)]
drm/omap: don't check dispc timings for DSI
While most display types only forward their VM to the DISPC, this
is not true for DSI. DSI calculates the VM for DISPC based on its
own, but it's not identical. Actually the DSI VM is not even a valid
DISPC VM making this check fail. Let's restore the old behaviour
and avoid checking the DISPC VM for DSI here.
Fixes:
7c27fa57ef31 ("drm/omap: Call dispc timings check operation directly")
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Sebastian Reichel [Thu, 23 May 2019 20:07:53 +0000 (22:07 +0200)]
drm/omap: use DRM_DEBUG_DRIVER instead of CORE
This macro is only used by omapdrm, which should print
debug messages using the DRIVER category instead of the
default CORE category.
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Kefeng Wang [Tue, 23 Apr 2019 07:50:01 +0000 (15:50 +0800)]
drm/omap: Use dev_get_drvdata()
Using dev_get_drvdata directly.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Emil Velikov [Wed, 22 May 2019 15:02:18 +0000 (16:02 +0100)]
drm/omap: remove open-coded drm_invalid_op()
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Thomas Meyer [Mon, 27 May 2019 20:41:15 +0000 (22:41 +0200)]
drm/omap: Make sure device_id tables are NULL terminated
Make sure (of/i2c/platform)_device_id tables are NULL terminated.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Thu, 28 Mar 2019 05:31:32 +0000 (07:31 +0200)]
drm: rcar-du: Add support for missing 16-bit RGB1555 formats
Add support for the DRM_FORMAT_RGBA5551, DRM_FORMAT_RGBX5551,
DRM_FORMAT_ABGR1555, DRM_FORMAT_XBGR1555, DRM_FORMAT_BGRA5551 and
DRM_FORMAT_BGRX5551 formats to the DU driver. Those formats are only
available on Gen3.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Laurent Pinchart [Thu, 28 Mar 2019 05:31:32 +0000 (07:31 +0200)]
drm: rcar-du: Add support for missing 16-bit RGB4444 formats
Add support for the DRM_FORMAT_RGBA4444, DRM_FORMAT_RGBX4444,
DRM_FORMAT_ABGR4444, DRM_FORMAT_XBGR4444, DRM_FORMAT_BGRA4444 and
DRM_FORMAT_BGRX4444 formats to the DU driver. Those formats are only
available on Gen3.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Laurent Pinchart [Thu, 28 Mar 2019 05:31:32 +0000 (07:31 +0200)]
drm: rcar-du: Add support for missing 32-bit RGB formats
Add support for the DRM_FORMAT_RGBA8888, DRM_FORMAT_RGBX8888,
DRM_FORMAT_ABGR8888 and DRM_FORMAT_XBGR8888 formats to the DU driver.
Those formats are only available on Gen3.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Laurent Pinchart [Mon, 4 Mar 2019 22:10:28 +0000 (00:10 +0200)]
drm: rcar-du: Skip LVDS1 output on Gen3 when using dual-link LVDS mode
In dual-link LVDS mode, the LVDS1 encoder is used as a companion for
LVDS0, and both encoders transmit data from DU0. The LVDS1 output of DU1
can't be used in that case, don't create an encoder and connector for
it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Laurent Pinchart [Mon, 4 Mar 2019 19:34:46 +0000 (21:34 +0200)]
drm: rcar-du: lvds: Add support for dual-link mode
In dual-link mode the LVDS0 encoder transmits even-numbered pixels, and
sends odd-numbered pixels to the LVDS1 encoder for transmission on a
separate link.
To implement support for this mode of operation, determine if the LVDS
connection operates in dual-link mode by querying the next device in the
pipeline, locate the companion encoder, and control it directly through
its bridge operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Laurent Pinchart [Wed, 6 Mar 2019 20:57:02 +0000 (22:57 +0200)]
drm: rcar-du: lvds: Remove LVDS double-enable checks
The DRM core and DU driver guarantee that the LVDS bridge will not be
double-enabled or double-disabled. Remove the corresponding unnecessary
checks.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Laurent Pinchart [Mon, 4 Mar 2019 21:51:18 +0000 (23:51 +0200)]
dt-bindings: display: renesas: lvds: Add renesas,companion property
Add a new optional renesas,companion property to point to the companion
LVDS encoder. This is used to support dual-link operation where the main
LVDS encoder splits even-numbered and odd-numbered pixels between the
two LVDS encoders.
The new property doesn't control the mode of operation, it only
describes the relationship between the master and companion LVDS
encoders.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Laurent Pinchart [Mon, 4 Mar 2019 19:56:07 +0000 (21:56 +0200)]
drm: bridge: thc63: Report input bus mode through bridge timings
Set a drm_bridge_timings in the drm_bridge, and use it to report the
input bus mode (single-link or dual-link). The other fields of the
timings structure are kept to 0 as they do not apply to LVDS buses.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Laurent Pinchart [Mon, 4 Mar 2019 19:47:51 +0000 (21:47 +0200)]
dt-bindings: display: bridge: thc63lvd1024: Document dual-link operation
The THC63LVD1024 LVDS decoder can operate in two modes, single-link or
dual-link. In dual-link mode both input ports are used to carry even-
and odd-numbered pixels separately. Document this in the DT bindings,
along with the related rules governing port and usage.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Laurent Pinchart [Mon, 4 Mar 2019 21:05:34 +0000 (23:05 +0200)]
drm: bridge: Add dual_link field to the drm_bridge_timings structure
Extend the drm_bridge_timings structure with a new dual_link field to
indicate that the bridge's input bus carries data on two separate
physical links. The first use case is LVDS dual-link mode where even-
and odd-numbered pixels are transferred on separate LVDS links.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Kieran Bingham [Fri, 17 May 2019 21:20:49 +0000 (22:20 +0100)]
drm: rcar-du: writeback: include interface header
The new writeback feature exports functions so that they can integrate
into the rcar_du_kms module.
The interface functions are defined in the rcar_du_writeback header, but
it is not included in the object file itself leading to compiler
warnings for missing prototypes.
Include the header as appropriate.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Biju Das [Fri, 12 Apr 2019 12:38:05 +0000 (13:38 +0100)]
drm: rcar-du: lvds: Add r8a774a1 support
The LVDS encoders on RZ/G2M SoC is similar to R-Car M3-W. Add support for
RZ/G2M (R8A774A1) SoC to the LVDS encoder driver.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Biju Das [Fri, 12 Apr 2019 12:38:04 +0000 (13:38 +0100)]
drm: rcar-du: Add R8A774A1 support
Add support for the R8A774A1 DU (which is very similar to the R8A7796 DU
except that it lacks TCON and CMM); it has one RGB output, one LVDS output
and one HDMI output.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Biju Das [Fri, 12 Apr 2019 12:38:03 +0000 (13:38 +0100)]
dt-bindings: display: renesas: lvds: Document r8a774a1 bindings
Document the RZ/G2M (R8A774A1) LVDS bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Biju Das [Fri, 12 Apr 2019 12:38:02 +0000 (13:38 +0100)]
dt-bindings: display: renesas: du: Document the r8a774a1 bindings
Document the RZ/G2M (R8A774A1) SoC in the R-Car DU bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Dave Airlie [Thu, 6 Jun 2019 03:47:40 +0000 (13:47 +1000)]
Merge branch 'drm-next-5.3' of git://people.freedesktop.org/~agd5f/linux into drm-next
amdgpu:
- Revert timeline support until KHR is ready
- Various driver reload fixes
- Refactor clock handling in DC
- Aux fixes for DC
- Bandwidth calculation updates for DC
- Fix documentation due to file rename
- RAS fix
- Fix race in late_init
ttm:
- Allow for better forward progress when there is heavy memory contention
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190606032537.6939-1-alexander.deucher@amd.com
Alex Deucher [Wed, 5 Jun 2019 14:54:27 +0000 (09:54 -0500)]
Revert "drm/amdgpu: add DRIVER_SYNCOBJ_TIMELINE to amdgpu"
This reverts commit
8d8a5a64a8904ea32bbf7292b89c11156d64f9a1.
Wait until KHR exposes the VLK support.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Tue, 4 Jun 2019 15:07:10 +0000 (17:07 +0200)]
drm/ttm: fix ttm_bo_unreserve
Since we now keep BOs on the LRU we need to explicitely remove
them from the LRU now after they are pinned.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Fri, 31 May 2019 16:34:57 +0000 (11:34 -0500)]
drm/amdgpu/display: Drop some new CONFIG_DRM_AMD_DC_DCN1_01 guards
These got added back by subsequent merges accidently.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Tue, 28 May 2019 19:17:25 +0000 (14:17 -0500)]
drm/amdgpu: fix a race in GPU reset with IB test (v2)
Split late_init into two functions, one (do_late_init) which
just does the hw init, and late_init which calls do_late_init
and schedules the IB test work. Call do_late_init in
the GPU reset code to run the init code, but not schedule
the IB test code. The IB test code is called directly
in the gpu reset code so no need to run the IB tests
in a separate work thread. If we do, we end up racing.
v2: Rework late_init. Pull out the mgpu fan boost and xgmi
pstate code into late_init so they get called in all cases.
rename the late_init worker thread to delayed work since it's
just the IB tests now which can happen later. Schedule the
work at init and resume time. It's not needed at reset time
because the IB tests are called directly.
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: Xinhui Pan <xinhui.pan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
xinhui pan [Fri, 17 May 2019 02:27:44 +0000 (10:27 +0800)]
drm/amdgpu: cancel late_init_work before gpu reset
gpu reset will run late_init and schedule the late_init_work. if we
keep triggering gpu reset in a short time, there are potenial races.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mauro Carvalho Chehab [Wed, 29 May 2019 23:23:42 +0000 (20:23 -0300)]
gpu: amdgpu: fix broken amdgpu_dma_buf.c references
This file was renamed, but docs weren't updated accordingly.
WARNING: kernel-doc './scripts/kernel-doc -rst -enable-lineno -function PRIME Buffer Sharing ./drivers/gpu/drm/amd/amdgpu/amdgpu_prime.c' failed with return code 1
WARNING: kernel-doc './scripts/kernel-doc -rst -enable-lineno -internal ./drivers/gpu/drm/amd/amdgpu/amdgpu_prime.c' failed with return code 2
Fixes:
2fbd6f94accdbb223a ("drm/amdgpu: rename amdgpu_prime.[ch] into amdgpu_dma_buf.[ch]")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dave Airlie [Thu, 6 Jun 2019 02:16:17 +0000 (12:16 +1000)]
Merge tag 'drm-misc-next-2019-06-05' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3:
UAPI Changes:
Cross-subsystem Changes:
- Add devicetree bindings for new panels.
- Convert allwinner's DT bindings to a schema.
- Drop video/hdmi static functions from kernel docs.
- Discard old fence when reserving space in reservation_object_get_fences_rcu.
Core Changes:
- Add missing -ENOMEM handling in edid loading.
- Fix null pointer deref in scheduler.
- Header cleanups, making them self-contained.
- Remove drmP.h inclusion from core.
- Fix make htmldocs warning in scheduler and HDR metadata.
- Fix a few warnings in the uapi header and add a doc section for it.
- Small MST sideband error handling fix.
- Clarify userspace review requirements.
- Clarify implicit/explicit fencing in docs.
- Flush output polling on shutdown.
Driver Changes:
- Small cleanups to stm.
- Add new driver for ST-Ericsson MCDE
- Kconfig fix for meson HDMI.
- Add support for Armadeus ST0700 Adapt panel.
- Add KOE tx14d24vm1bpa panel.
- Update timings for st7701.
- Fix compile error in mcde.
- Big series of tc358767 fixes, and enabling support for IRQ and HPD handling.
- Assorted fixes to sii902x, and implementing HDMI audio support.
- Enable HDR metadata support on amdgpu.
- Assorted fixes to atmel-hlcdc, and add sam9x60 LCD controller support.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6c43ffa9-11ff-5354-d772-c20fd4d1e3d9@linux.intel.com
Chris Wilson [Tue, 4 Jun 2019 12:53:23 +0000 (13:53 +0100)]
dma-buf: Discard old fence_excl on retrying get_fences_rcu for realloc
If we have to drop the seqcount & rcu lock to perform a krealloc, we
have to restart the loop. In doing so, be careful not to lose track of
the already acquired exclusive fence.
Fixes:
fedf54132d24 ("dma-buf: Restart reservation_object_get_fences_rcu() after writes")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: stable@vger.kernel.org #v4.10
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190604125323.21396-1-chris@chris-wilson.co.uk
Claudiu Beznea [Thu, 25 Apr 2019 12:36:39 +0000 (12:36 +0000)]
drm/atmel-hlcdc: revert shift by 8
Revert shift by 8 of state->base.alpha. This introduced a
regression on planes.
Fixes:
7f73c10b256b ("drm/atmel-hclcdc: Convert to the new generic alpha property")
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1556195748-11106-7-git-send-email-claudiu.beznea@microchip.com
Sandeep Sheriker Mallikarjun [Thu, 25 Apr 2019 12:36:35 +0000 (12:36 +0000)]
drm: atmel-hlcdc: add sam9x60 LCD controller
Add the LCD controller for SAM9X60.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
[claudiu.beznea@microchip.com: add fixed_clksrc option to
atmel_hlcdc_dc_sam9x60]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1556195748-11106-6-git-send-email-claudiu.beznea@microchip.com
Sandeep Sheriker Mallikarjun [Thu, 25 Apr 2019 12:36:30 +0000 (12:36 +0000)]
drm: atmel-hlcdc: enable sys_clk during initalization.
For SAM9X60 SoC, sys_clk is through lcd_gclk clock source and this
needs to be enabled before enabling lcd_clk.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
[claudiu.beznea@microchip.com: add fixed_clksrc checks]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1556195748-11106-5-git-send-email-claudiu.beznea@microchip.com
Claudiu Beznea [Thu, 25 Apr 2019 12:36:16 +0000 (12:36 +0000)]
drm: atmel-hlcdc: avoid initializing cfg with zero
Remove cfg initialization with zero and read state with
drm_crtc_state_to_atmel_hlcdc_crtc_state() so that cfg to be initialized
with state's output_mode.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1556195748-11106-3-git-send-email-claudiu.beznea@microchip.com
Claudiu Beznea [Thu, 25 Apr 2019 12:36:09 +0000 (12:36 +0000)]
drm: atmel-hlcdc: add config option for clock selection
SAM9x60 LCD Controller has no option to select clock source as previous
controllers have. To be able to use the same driver even for this LCD
controller add a config option to know if controller supports this.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1556195748-11106-2-git-send-email-claudiu.beznea@microchip.com
Chris Wilson [Mon, 3 Jun 2019 13:58:57 +0000 (14:58 +0100)]
drm: Flush output polling on shutdown
We need to mark the output polling as disabled to prevent concurrent
irqs from queuing new work as shutdown the probe -- causing that work to
execute after we have freed the structs:
<4> [341.846490] DEBUG_LOCKS_WARN_ON(mutex_is_locked(lock))
<4> [341.846497] WARNING: CPU: 3 PID: 3300 at kernel/locking/mutex-debug.c:103 mutex_destroy+0x49/0x50
<4> [341.846508] Modules linked in: i915(-) vgem thunderbolt snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic mei_hdcp x86_pkg_temp_thermal coretemp crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm mcs7830 btusb usbnet btrtl mii btbcm btintel bluetooth ecdh_generic ecc mei_me mei prime_numbers i2c_hid pinctrl_sunrisepoint pinctrl_intel [last unloaded: i915]
<4> [341.846546] CPU: 3 PID: 3300 Comm: i915_module_loa Tainted: G U 5.2.0-rc2-CI-CI_DRM_6175+ #1
<4> [341.846553] Hardware name: Dell Inc. XPS 13 9360/0823VW, BIOS 2.9.0 07/09/2018
<4> [341.846560] RIP: 0010:mutex_destroy+0x49/0x50
<4> [341.846565] Code: 00 00 5b c3 e8 a8 9f 3b 00 85 c0 74 ed 8b 05 3e 55 23 01 85 c0 75 e3 48 c7 c6 00 d0 08 82 48 c7 c7 a8 aa 07 82 e8 e7 08 fa ff <0f> 0b eb cc 0f 1f 00 48 b8 11 11 11 11 11 11 11 11 48 89 76 20 48
<4> [341.846578] RSP: 0018:
ffffc900006cfdb0 EFLAGS:
00010286
<4> [341.846583] RAX:
0000000000000000 RBX:
ffff88826759a168 RCX:
0000000000000000
<4> [341.846589] RDX:
0000000000000002 RSI:
0000000000000000 RDI:
ffffffff8112844c
<4> [341.846595] RBP:
ffff8882708fa548 R08:
0000000000000000 R09:
0000000000039600
<4> [341.846601] R10:
0000000000000000 R11:
0000000000000ce4 R12:
ffffffffa07de1e0
<4> [341.846607] R13:
0000000000000000 R14:
0000000000000000 R15:
ffffffffa07de2d0
<4> [341.846613] FS:
00007f62b5ae0e40(0000) GS:
ffff888276380000(0000) knlGS:
0000000000000000
<4> [341.846620] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
<4> [341.846626] CR2:
000055a4e064f4a0 CR3:
0000000266b16006 CR4:
00000000003606e0
<4> [341.846632] Call Trace:
<4> [341.846639] drm_fb_helper_fini.part.17+0xb3/0x100
<4> [341.846682] intel_fbdev_fini+0x20/0x80 [i915]
<4> [341.846722] intel_modeset_cleanup+0x9a/0x140 [i915]
<4> [341.846750] i915_driver_unload+0xa3/0x100 [i915]
<4> [341.846778] i915_pci_remove+0x19/0x30 [i915]
<4> [341.846784] pci_device_remove+0x36/0xb0
<4> [341.846790] device_release_driver_internal+0xd3/0x1b0
<4> [341.846795] driver_detach+0x3f/0x80
<4> [341.846800] bus_remove_driver+0x53/0xd0
<4> [341.846805] pci_unregister_driver+0x25/0xa0
<4> [341.846843] i915_exit+0x16/0x1c [i915]
<4> [341.846849] __se_sys_delete_module+0x162/0x210
<4> [341.846855] ? trace_hardirqs_off_thunk+0x1a/0x1c
<4> [341.846859] ? do_syscall_64+0xd/0x1c0
<4> [341.846864] do_syscall_64+0x55/0x1c0
<4> [341.846869] entry_SYSCALL_64_after_hwframe+0x49/0xbe
<4> [341.846875] RIP: 0033:0x7f62b51871b7
<4> [341.846881] Code: 73 01 c3 48 8b 0d d1 8c 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d a1 8c 2c 00 f7 d8 64 89 01 48
<4> [341.846897] RSP: 002b:
00007ffe7a227138 EFLAGS:
00000206 ORIG_RAX:
00000000000000b0
<4> [341.846904] RAX:
ffffffffffffffda RBX:
00007ffe7a2272b0 RCX:
00007f62b51871b7
<4> [341.846910] RDX:
0000000000000001 RSI:
0000000000000800 RDI:
0000557cd6b55948
<4> [341.846916] RBP:
0000557cd6b558e0 R08:
0000557cd6b5594c R09:
00007ffe7a227160
<4> [341.846922] R10:
00007ffe7a226134 R11:
0000000000000206 R12:
0000000000000000
<4> [341.846927] R13:
00007ffe7a227820 R14:
0000000000000000 R15:
0000000000000000
<4> [341.846936] irq event stamp:
3547847
<4> [341.846940] hardirqs last enabled at (
3547847): [<
ffffffff819aad2c>] _raw_spin_unlock_irqrestore+0x4c/0x60
<4> [341.846949] hardirqs last disabled at (
3547846): [<
ffffffff819aab9d>] _raw_spin_lock_irqsave+0xd/0x50
<4> [341.846957] softirqs last enabled at (
3547376): [<
ffffffff81c0033a>] __do_softirq+0x33a/0x4b9
<4> [341.846966] softirqs last disabled at (
3547367): [<
ffffffff810b6379>] irq_exit+0xa9/0xc0
<4> [341.846973] WARNING: CPU: 3 PID: 3300 at kernel/locking/mutex-debug.c:103 mutex_destroy+0x49/0x50
<4> [341.846980] ---[ end trace
ba94ca8952ba970e ]---
<7> [341.866547] [drm:intel_dp_detect [i915]] MST support? port A: no, sink: no, modparam: yes
<7> [341.890480] [drm:drm_add_display_info] non_desktop set to 0
<7> [341.890530] [drm:drm_add_edid_modes] ELD: no CEA Extension found
<7> [341.890537] [drm:drm_add_display_info] non_desktop set to 0
<7> [341.890578] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:86:eDP-1] probed modes :
<7> [341.890589] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [341.890602] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<4> [341.890628] general protection fault: 0000 [#1] PREEMPT SMP PTI
<4> [341.890636] CPU: 0 PID: 508 Comm: kworker/0:4 Tainted: G U W 5.2.0-rc2-CI-CI_DRM_6175+ #1
<4> [341.890646] Hardware name: Dell Inc. XPS 13 9360/0823VW, BIOS 2.9.0 07/09/2018
<4> [341.890655] Workqueue: events output_poll_execute
<4> [341.890663] RIP: 0010:drm_setup_crtcs+0x13e/0xbe0
<4> [341.890669] Code: 00 41 8b 44 24 58 85 c0 0f 8e f9 01 00 00 44 8b 6c 24 20 44 8b 74 24 28 31 db 31 ed 49 8b 44 24 60 48 63 d5 44 89 ee 83 c5 01 <48> 8b 04 d0 44 89 f2 48 8b 38 48 8b 87 88 01 00 00 48 8b 40 20 e8
<4> [341.890686] RSP: 0018:
ffffc9000033fd40 EFLAGS:
00010202
<4> [341.890692] RAX:
6b6b6b6b6b6b6b6b RBX:
0000000000000002 RCX:
0000000000000000
<4> [341.890700] RDX:
0000000000000001 RSI:
0000000000000c80 RDI:
00000000ffffffff
<4> [341.890707] RBP:
0000000000000002 R08:
0000000000000000 R09:
0000000000000000
<4> [341.890715] R10:
0000000000000c80 R11:
0000000000000000 R12:
ffff888267599fe8
<4> [341.890722] R13:
0000000000000c80 R14:
0000000000000708 R15:
0000000000000007
<4> [341.890730] FS:
0000000000000000(0000) GS:
ffff888276200000(0000) knlGS:
0000000000000000
<4> [341.890739] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
<4> [341.890745] CR2:
000055a4e064f4a0 CR3:
000000026d234003 CR4:
00000000003606f0
<4> [341.890752] Call Trace:
<4> [341.890760] drm_fb_helper_hotplug_event.part.24+0x89/0xb0
<4> [341.890768] drm_kms_helper_hotplug_event+0x21/0x30
<4> [341.890774] output_poll_execute+0x9d/0x1a0
<4> [341.890782] process_one_work+0x245/0x610
<4> [341.890790] worker_thread+0x37/0x380
<4> [341.890796] ? process_one_work+0x610/0x610
<4> [341.890802] kthread+0x119/0x130
<4> [341.890808] ? kthread_park+0x80/0x80
<4> [341.890815] ret_from_fork+0x3a/0x50
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109964
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190603135910.15979-2-chris@chris-wilson.co.uk
Uma Shankar [Mon, 3 Jun 2019 13:08:50 +0000 (18:38 +0530)]
video/hdmi: Dropped static functions from kernel doc
Dropped static functions from kernel documentation.
v2: Dropped the comments altogether for static functions,
as the definitions seems self explanatory.
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1559567330-25182-4-git-send-email-uma.shankar@intel.com
Uma Shankar [Tue, 4 Jun 2019 11:17:02 +0000 (16:47 +0530)]
drm: Fix docbook warnings in hdr metadata helper structures
Fixes the following warnings:
./include/drm/drm_mode_config.h:841: warning: Incorrect use of
kernel-doc format: * hdr_output_metadata_property: Connector
property containing hdr
./include/drm/drm_mode_config.h:918: warning: Function parameter or member 'hdr_output_metadata_property' not described in 'drm_mode_config'
./include/drm/drm_connector.h:1251: warning: Function parameter or member 'hdr_output_metadata' not described in 'drm_connector'
./include/drm/drm_connector.h:1251: warning: Function parameter or member 'hdr_sink_metadata' not described in 'drm_connector'
Also adds some property documentation for HDR Metadata Connector
Property in connector property create function.
v2: Fixed Sean Paul's review comments.
v3: Fixed Daniel Vetter's review comments, added the UAPI structure
definition section in kernel docs.
v4: Fixed Daniel Vetter's review comments.
v5: Added structure member references as per Daniel's suggestion.
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Ville Syrjä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: "Ville Syrjä" <ville.syrjala@linux.intel.com>
Cc: Hans Verkuil <hansverk@cisco.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Reviewed-by: Sean Paul <sean@poorly.run> (v1)
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
[danvet: Fix up markup: () for functions, & for structs. Style guide
also recommends to prepend struct for structures.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1559647022-7336-1-git-send-email-uma.shankar@intel.com
Uma Shankar [Mon, 3 Jun 2019 13:08:48 +0000 (18:38 +0530)]
drm: ADD UAPI structure definition section in kernel doc
Add a new section for UAPI structure and helper definitions
in kernel docbook.
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1559567330-25182-2-git-send-email-uma.shankar@intel.com
Noralf Trønnes [Fri, 31 May 2019 14:01:11 +0000 (16:01 +0200)]
drm/fb-helper: Remove drm_fb_helper_crtc
struct drm_fb_helper_crtc is now just a wrapper around drm_mode_set so
use that directly instead and attach it as a modeset array onto
drm_client_dev. drm_fb_helper will use this array to store its modesets
which means it will always initialize a drm_client, but it will not
register the client (callbacks) unless it's the generic fbdev emulation.
Code will later be moved to drm_client, so add code there in a new file
drm_client_modeset.c with MIT license to match drm_fb_helper.c.
The modeset connector array size is hardcoded for the cloned case to avoid
having to pass in a value from the driver. A value of 8 is chosen to err
on the safe side. This means that the max connector argument for
drm_fb_helper_init() and drm_fb_helper_fbdev_setup() isn't used anymore,
a todo entry for this is added.
In pan_display_atomic() restore_fbdev_mode_force() is used instead of
restore_fbdev_mode_atomic() because that one will later become internal
to drm_client_modeset.
Locking order:
1. drm_fb_helper->lock
2. drm_master_internal_acquire
3. drm_client_dev->modeset_mutex
v6: Improve commit message (Sam Ravnborg)
v3:
- Use full drm_client_init/release for the modesets (Daniel Vetter)
- drm_client_for_each_modeset: use lockdep_assert_held (Daniel Vetter)
- Hook up to Documentation/gpu/drm-client.rst (Daniel Vetter)
v2:
- Add modesets array to drm_client (Daniel Vetter)
- Use a new file for the modeset code (Daniel Vetter)
- File has to be MIT licensed (Emmanuel Vadot)
- Add copyrights from drm_fb_helper.c
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190531140117.37751-3-noralf@tronnes.org
Daniel Vetter [Mon, 3 Jun 2019 14:28:48 +0000 (16:28 +0200)]
drm/docs: More links for implicit/explicit fencing.
drm_atomic_set_fence_for_plane() contains the main discussion from a
driver pov, link to that from more places.
Cc: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190603142848.26487-1-daniel.vetter@ffwll.ch
Nicholas Kazlauskas [Tue, 28 May 2019 19:08:36 +0000 (15:08 -0400)]
drm/amd/display: Only force modesets when toggling HDR
[Why]
We can issue HDR static metadata as part of stream updates for
non-modesets as long as we force a modeset when entering or exiting HDR.
This avoids unnecessary blanking for simple metadata updates.
[How]
When changing scaling and abm for the stream also check if HDR has
changed and send the stream update. This will only happen in non-modeset
cases.
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528190836.10738-3-nicholas.kazlauskas@amd.com
Nicholas Kazlauskas [Tue, 28 May 2019 19:08:35 +0000 (15:08 -0400)]
drm/amd/display: Expose HDR output metadata for supported connectors
[Why]
For userspace to send static HDR metadata to the display we need to
attach the property on the connector and send it to DC.
[How]
The property is attached to HDMI and DP connectors. Since the metadata
isn't actually available when creating the connector this isn't a
property we can dynamically support based on the extension block
being available or not.
When the HDR metadata is changed a modeset will be forced for now.
We need to switch from 8bpc to 10bpc in most cases anyway, and we want
to fully exit HDR mode when userspace gives us a NULL metadata, so this
isn't completely unnecessary.
The requirement can later be reduced to just entering and exiting HDR
or switching max bpc.
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528190836.10738-2-nicholas.kazlauskas@amd.com
Uma Shankar [Wed, 29 May 2019 19:59:03 +0000 (01:29 +0530)]
drm: Fixed doc warnings in drm uapi header
Fixed doc warnings in drm uapi header. All the UAPI
structures are now documented in kernel doc.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1559159944-21103-4-git-send-email-uma.shankar@intel.com
Uma Shankar [Wed, 29 May 2019 19:59:01 +0000 (01:29 +0530)]
drm: Drop a redundant unused variable
Drop a redundant and unused variable "hdr_output_metadata" from
drm_connector.
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1559159944-21103-2-git-send-email-uma.shankar@intel.com
Daniel Vetter [Tue, 21 May 2019 08:48:49 +0000 (10:48 +0200)]
drm/doc: More fine-tuning on userspace review requirements
With Eric's patch
commit
ba6e798ecf320716780bb6a6088a8d17dcba1d49
Author: Eric Anholt <eric@anholt.net>
Date: Wed Apr 24 11:56:17 2019 -0700
drm/doc: Document expectation that userspace review looks at kernel uAPI.
there's been concerns raised that we expect userspace people to do
in-depth kernel patch review. That's not reasonable, same way kernel
people can't review all the userspace we have. Try to clarify
expectations a bit more.
Cc: Eric Anholt <eric@anholt.net>
Cc: Pekka Paalanen <ppaalanen@gmail.com>
Cc: contact@emersion.fr
Cc: wayland-devel@lists.freedesktop.org
Acked-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521084849.27452-1-daniel.vetter@ffwll.ch
Chunming Zhou [Tue, 7 May 2019 11:45:31 +0000 (19:45 +0800)]
drm/amd/display: use ttm_eu_reserve_buffers instead of amdgpu_bo_reserve v2
add ticket for display bo, so that it can preempt busy bo.
v2: fix stupid rebase error
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Wed, 22 May 2019 07:51:47 +0000 (09:51 +0200)]
drm/ttm: fix busy memory to fail other user v10
BOs on the LRU might be blocked during command submission
and cause OOM situations.
Avoid this by blocking for the first busy BO not locked by
the same ticket as the BO we are searching space for.
v10: completely start over with the patch since we didn't
handled a whole bunch of corner cases.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Mon, 13 May 2019 15:58:23 +0000 (17:58 +0200)]
drm/ttm: immediately move BOs to the new LRU v3
Move BOs which are currently in a lower domain to the new
LRU before allocating backing space while validating.
This makes sure that we always have enough entries on the
LRU to allow for other processes to wait for an operation
to complete.
v2: generalize the test
v3: fix rebase error
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Mon, 13 May 2019 15:34:29 +0000 (17:34 +0200)]
drm/ttm: cleanup ttm_bo_mem_space
We tried this once before, but that turned out to be more
complicated than thought. With all the right prerequisites
it looks like we can do this now.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Mon, 13 May 2019 13:42:52 +0000 (15:42 +0200)]
drm/ttm: remove manual placement preference
If drivers don't prefer a system memory placement
they should not but it into the placement list first.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Mon, 13 May 2019 13:36:08 +0000 (15:36 +0200)]
drm/ttm: return immediately in case of a signal
When a signal arrives we should return immediately for
handling it and not try other placements first.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Fri, 10 May 2019 12:15:08 +0000 (14:15 +0200)]
drm/ttm: Make LRU removal optional v2
We are already doing this for DMA-buf imports and also for
amdgpu VM BOs for quite a while now.
If this doesn't run into any problems we are probably going
to stop removing BOs from the LRU altogether.
v2: drop BUG_ON from ttm_bo_add_to_lru
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Emily Deng [Fri, 31 May 2019 09:35:27 +0000 (17:35 +0800)]
drm/amdgpu/display: Fix reload driver error
Issue:
Will have follow error when reload driver:
[ 3986.567739] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:07.0/drm_dp_aux_dev'
[ 3986.567743] CPU: 6 PID: 1767 Comm: modprobe Tainted: G OE 5.0.0-rc1-custom #1
[ 3986.567745] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
[ 3986.567746] Call Trace:
......
[ 3986.567808] drm_dp_aux_register_devnode+0xdc/0x140 [drm_kms_helper]
......
[ 3986.569081] kobject_add_internal failed for drm_dp_aux_dev with -EEXIST, don't try to register things with the same name in the same directory.
Reproduce sequences:
1.modprobe amdgpu
2.modprobe -r amdgpu
3.modprobe amdgpu
Root cause:
When unload driver, it doesn't unregister aux.
v2: Don't use has_aux
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Emily Deng [Fri, 31 May 2019 09:30:39 +0000 (17:30 +0800)]
drm/amdgpu/sriov: Correct some register program method
For the VF, some registers only could be programmed with RLC.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Trigger Huang <Trigger.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Oak Zeng [Tue, 28 May 2019 19:51:49 +0000 (14:51 -0500)]
drm/amdkfd: Return proper error code for gws alloc API
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Aric Cyr [Thu, 16 May 2019 22:43:54 +0000 (18:43 -0400)]
drm/amd/display: program manual trigger only for bottom most pipe
[Why]
We only want to manual trigger end-of-frame when the bottom-most
pipe is flipped to prevent overlays from ending the frame too early.
[How]
Check that the manual trigger is only firing on bottom plane.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Krunoslav Kovac [Thu, 16 May 2019 15:14:55 +0000 (11:14 -0400)]
drm/amd/display: CS_TFM_1D only applied post EOTF
[Why]
There's some unnecessary mem allocation for CS_TFM_ID. What's worse, it
depends on LUT size and since it's 4K for CS_TFM_1D, it is 16x bigger
than in regular case when it's actually needed. This leads to some
crashes in stress conditions.
[How]
Skip ramp combining designed for RGB256 and DXGI gamma with CS_TFM_1D.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nicholas Kazlauskas [Wed, 1 May 2019 14:26:09 +0000 (10:26 -0400)]
drm/amd/display: Reset planes for color management changes
[Why]
For commits with allow_modeset=false and CRTC degamma changes the planes
aren't reset. This results in incorrect rendering.
[How]
Reset the planes when color management has changed on the CRTC.
Technically this will include regamma changes as well, but it doesn't
really after legacy userspace since those commit with
allow_modeset=true.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eryk Brol [Wed, 15 May 2019 19:12:41 +0000 (15:12 -0400)]
drm/amd/display: Increase Backlight Gain Step Size
[Why]
Some backlight tests fail due to backlight settling
taking too long. This happens because the step
size used to change backlight levels is too small.
[How]
1. Change the size of the backlight gain step size
2. Change how DMCU firmware gets the step size value
so that it is passed in by driver during DMCU initn
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Anthony Koo [Wed, 15 May 2019 20:39:23 +0000 (16:39 -0400)]
drm/amd/display: fix issues with bad AUX reply on some displays
[Why]
Some displays take some time to power up AUX CH once they are
put into D3 state via write to DPCD 600h=2.
Interestingly enough, some display may simply NACK, but some might
also ACK with a bunch of 0s, which can cause issues with receiver
cap retrieval. Note that not all DPCD address return 0s, but in
particular it has been observed on some higher DPCD address such
as DPCD 2200h, etc.
[How]
Based on spec, receiver will monitor differential signal while in D3 and
AUX CH is in low power mode. When detected, it may allow up to
1 ms to power up AUX CH and reply.
If we read Sink power state D3, we should add 1 ms delay to satisfy
this spec requirement.
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eric Bernstein [Wed, 8 May 2019 20:08:39 +0000 (16:08 -0400)]
drm/amd/display: Refactor DIO stream encoder
* Pull duplicate audio_clock_info struct to stream_encoder.h
* Generalize sec_gsp7* to sec_gsp_pps*
* Expose enc1 and enc2 stream encoder audio funcs
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Daniel He [Wed, 15 May 2019 03:38:37 +0000 (11:38 +0800)]
drm/amd/display: Modified AUX_DPHY_RX_CONTROL0
[Description] This is cause by failing to read link caps from driver.
Signed-off-by: Daniel He <daniel.he@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ilya Bakoulin [Fri, 12 Apr 2019 20:47:08 +0000 (16:47 -0400)]
drm/amd/display: Add writeback_config to VBA vars
Adding writeback_config enum to vba_vars_st, replacing old flag.
Initialize to dm_normal.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eric Yang [Wed, 8 May 2019 23:06:30 +0000 (19:06 -0400)]
drm/amd/display: Refactor clk_mgr functions
[Why]
Some HW specific implementations can be pulled out into clk_mgr.c.
[How]
* Pull get_active_display_cnt out to clk_mgr.
* Pull out shared logic in set_dispclk and set_dprefclk
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eric Yang [Wed, 10 Apr 2019 20:31:08 +0000 (16:31 -0400)]
drm/amd/display: Fix type of pp_smu_wm_set_range struct
[why]
Value read from SMU is 16 bits, not 32.
[How]
Fix type, and add wm_type enum in preparation for future interfaces.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Anthony Koo [Fri, 10 May 2019 18:57:48 +0000 (14:57 -0400)]
drm/amd/display: do not power on eDP power rail early
[Why]
Modern Standby may toggle display adapter state between D0
and D3 state unpredictably.
But events that cause transition to D0 are not always resulting
in a display light up scenario.
Modern eDP panels should be able to power on panel logic
quickly upon VDD going high. Based on spec, the T3 time
between VDD on and HPD high can be between 0 and 80 ms.
Doing any tricky sorts of optimization by powering on panel
VDD early during D0 transition on can negatively impact other
features due to unnecessary power drain and toggling when
final system state does not intend for the panel to be lit up.
We need OEMs to source higher end panels that have T3 time
close to 0 if they want quick S3/Modern Standby resume times.
[How]
Remove panel VDD power on in init_hw
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Su Sung Chung [Fri, 10 May 2019 19:16:45 +0000 (15:16 -0400)]
drm/amd/display: fix crash on setmode when mode is close to bw limit
[why]
during It's possible to call dcn_validate_bandwidth with no plane.
In that case, as we are only intersted in if output timing is supported or not,
even if we cannot support native resolution, we still want to support lower
resolution if it is valid
[how]
if there exist no surface, make viewport/rec_out size at max 1080p. It is
already known that 1080p x 6(max # of pipes) is supported, so if we fail
validation, it is because of the stream
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Su Sung Chung [Wed, 1 May 2019 20:54:56 +0000 (16:54 -0400)]
drm/amd/display: fix calculation of total_data_read_bandwidth
[why]
by adding fast_validate flag, we are skipping some portion of
dcn_validate_bandwidth code that is not necessary for mode validation.
However we have a bug where it does not calculate
v->total_data_read_bandwidth, which is one of the factors determines the
result of the validation, and therefore report false positive during
mode validation.
[how]
add calculation of v->total_data_read_bandwidth outside of the region
that is guarded by fast_validate flag
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Aric Cyr [Fri, 10 May 2019 21:01:01 +0000 (17:01 -0400)]
drm/amd/display: 3.2.32
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Chris Park [Fri, 10 May 2019 17:34:30 +0000 (13:34 -0400)]
drm/amd/display: Move link functions from dc to dc_link
[Why]
link-specific functions should reside in dc_link.c
[How]
Move them there.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jun Lei [Thu, 9 May 2019 19:32:27 +0000 (15:32 -0400)]
drm/amd/display: Add min_dcfclk_mhz field to bb overrides
Add min_dcfclk_mhz to bounding box overrides.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eric Yang [Tue, 7 May 2019 16:47:37 +0000 (12:47 -0400)]
drm/amd/display: move clk_mgr files to right place
[Why]
Better organization
[How]
Move clk_mgr files under dc/clk_mgr
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Paul Hsieh [Tue, 7 May 2019 09:58:58 +0000 (17:58 +0800)]
drm/amd/display: disable PSR/ABM before destroy DMCU struct
[Why]
1. DMCU is not running on some platform but driver still send ABM
command. It may cause assert due to DMCU is not alive.
2. To make sure PSR disable when driver disable
[How]
1. Add dmcu_is_running in ABM struct, driver can check this flag to
determine driver should send ABM command or not.
2. Send PSR disable command when destroy PSR
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eryk Brol [Tue, 23 Apr 2019 15:53:52 +0000 (11:53 -0400)]
drm/amd/display: Ensure DRR triggers in BP
[Why]
In the previous implementation DRR event sometimes came
in during FP2 region which is a keep-out zone. This
would cause the frame not to latch until the next frame
which resulted in heavy flicker. To fix this we need
to make sure that it triggers in the BP.
[How]
1. Remove DRR programming during flip
2. Setup manual trigger for DRR event and trigger it
after surface programming is complete
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Krunoslav Kovac [Fri, 15 Mar 2019 20:25:41 +0000 (16:25 -0400)]
drm/amd/display: Add GSL source select registers
GSL is a form of locking that can be used to synchronize pipes in a
pipe-split configurations when async flip is used. Add the registers
here.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eryk Brol [Wed, 8 May 2019 13:08:03 +0000 (09:08 -0400)]
drm/amd/display: Disable audio stream only if it's currently enabled
[Why]
Previously there were 2 consecutive calls being made to disable
audio stream. The first one disabled the audio stream, and the second
one went through and also tried to disable the audio stream causing
BACO entry issues due to the ASIC appearing busy.
[How]
1. Add a status field to the audio struct which stores enabled/disabled
info
2. In the calls to enable/disable audio stream check if we're already
in the desired state before executing the function
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Wenjing Liu [Tue, 7 May 2019 19:18:44 +0000 (15:18 -0400)]
drm/amd/display: assign new stream id in dc_copy_stream
[why]
stream id should uniquely identify an instance of stream.
the copy constructor should be treated as a new
stream instance.
[how]
assign a new stream id in this copy constructor.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eric Yang [Tue, 7 May 2019 21:29:11 +0000 (17:29 -0400)]
drm/amd/display: Move CLK_BASE_INNER macro
This macro is specificly used by RV1. Move it to the appropriate
location.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Gary Kattan [Fri, 22 Feb 2019 20:51:18 +0000 (12:51 -0800)]
drm/amd/display: Implement CM dealpha and bias interfaces
Add vtable entries for de-alpha and bias color management interfaces.
Move piece-wise transfer function registers to a helper list for future
reuse.
Signed-off-by: Gary Kattan <gary.kattan@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hugo Hu [Fri, 3 May 2019 07:36:29 +0000 (15:36 +0800)]
drm/amd/display: Don't use ROM for output TF if GAMMA_CS_TFM_1D
We can’t use hardcoded SRGB ROM for output TF if we have GAMMA_CS_TFM_1D
(unless we know 1D LUT is identity), so we never want to return here early.
We apply the LUT part of ColorTransform3x4 only in apply_lut_1d() which is
called near the end of that function.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>