OSDN Git Service
Marc Kleine-Budde [Tue, 2 Sep 2014 14:54:17 +0000 (16:54 +0200)]
can: flexcan: increase FLEXCAN_MCR_MAXMB() macro to 7 bits
This patch increases the mask in the FLEXCAN_MCR_MAXMB() to 7 bits as in the
newer flexcan cores the MAXMB field is 7 bits wide.
Reported-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 16 Sep 2014 13:31:27 +0000 (15:31 +0200)]
can: flexcan: put TX mailbox into TX_INACTIVE mode after tx-complete
After sending a RTR frame the TX mailbox becomes a RX_EMPTY mailbox. To avoid
side effects when the RX-FIFO is full, this patch puts the TX mailbox into
TX_INACTIVE mode in the transmission complete interrupt handler. This, of
course, leaves a race window between the actual completion of the transmission
and the handling of tx-complete interrupt. However this is the best we can do
without busy polling the tx complete interrupt.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
David Jander [Wed, 3 Sep 2014 14:47:22 +0000 (16:47 +0200)]
can: flexcan: implement workaround for errata ERR005829
This patch implements the workaround mentioned in ERR005829:
ERR005829: FlexCAN: FlexCAN does not transmit a message that is enabled to
be transmitted in a specific moment during the arbitration process.
Workaround: The workaround consists of two extra steps after setting up a
message for transmission:
Step 8: Reserve the first valid mailbox as an inactive mailbox (CODE=0b1000).
If RX FIFO is disabled, this mailbox must be message buffer 0. Otherwise, the
first valid mailbox can be found using the "RX FIFO filters" table in the
FlexCAN chapter of the chip reference manual.
Step 9: Write twice INACTIVE code (0b1000) into the first valid mailbox.
Signed-off-by: David Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
David Jander [Wed, 27 Aug 2014 09:58:05 +0000 (11:58 +0200)]
can: flexcan: correctly initialize mailboxes
Apparently mailboxes may contain random data at startup, causing some of them
being prepared for message reception. This causes overruns being missed or even
confusing the IRQ check for trasmitted messages, increasing the transmit
counter instead of the error counter.
This patch initializes all mailboxes after the FIFO as RX_INACTIVE.
Signed-off-by: David Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 16 Sep 2014 10:39:28 +0000 (12:39 +0200)]
can: flexcan: mark TX mailbox as TX_INACTIVE
This patch fixes the initialization of the TX mailbox. It is now correctly
initialized as TX_INACTIVE not RX_EMPTY.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Tue, 16 Sep 2014 08:05:41 +0000 (10:05 +0200)]
can: peak_pci: add PCI ID definition pcie card variant
Add PCI ID definition for the single channel PCAN ExpressCard 34 adapter. Due
to the subsystem id evaluation the correct number of channels (here 1) is
created at initialization time. Tested including the LED functionality.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Roger Quadros [Tue, 9 Sep 2014 14:31:08 +0000 (17:31 +0300)]
can: c_can_platform: fix parameters of c_can_hw_raminit_ti()
Pass the correct 'mask' and 'value' bits to c_can_hw_raminit_wait_ti(). They
seem to have been swapped in the usage instances.
Reported-by: Jay Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Randy Dunlap [Tue, 16 Sep 2014 20:47:41 +0000 (13:47 -0700)]
scsi: use 'depends' instead of 'select' for SCSI_FC_ATTRS
There are other kconfig symbols which use SCSI_FC_ATTRS.
In order to maintain sanity and prevent kconfig warnings, change
all of these from using 'select' to using 'depends on' so that
proper symbol dependencies will be honored and circular depends
problems will be avoided.
This fixes kconfig warnings and build errors:
warning: (LIBFC && SCSI_IBMVFC && SCSI_QLA_FC && SCSI_LPFC && ZFCP && SCSI_BFA_FC && SCSI_CHELSIO_FCOE && FUSION_FC) selects SCSI_FC_ATTRS which has unmet direct dependencies (SCSI && NET)
drivers/scsi/scsi_transport_fc.c: In function 'fc_host_post_event':
drivers/scsi/scsi_transport_fc.c:543:7: error: 'scsi_nl_sock' undeclared (first use in this function)
drivers/scsi/scsi_transport_fc.c: In function 'fc_host_post_vendor_event':
drivers/scsi/scsi_transport_fc.c:611:7: error: 'scsi_nl_sock' undeclared (first use in this function)
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Tue, 16 Sep 2014 16:05:21 +0000 (17:05 +0100)]
sfc: fix addr_list_lock spinlock use before init
Reported by Nikolay Aleksandrov. In efx_init_port() we call
efx_mac_reconfigure() to work around a Falcon/A1 limitation, and this calls
efx_{arch}_filter_sync_rx_mode(), which takes the addr_list_lock; but this
lock is uninitialised, because we haven't called register_netdevice() yet.
So, in efx_farch_filter_sync_rx_mode(), check efx_dev_registered() before
doing anything else.
The EF10 equivalent, efx_ef10_filter_sync_rx_mode(), already has the
corresponding check.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Tested-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Tue, 16 Sep 2014 03:40:47 +0000 (11:40 +0800)]
r8169: adjust __rtl8169_set_features
Remove the "changed" test in __rtl8169_set_features(). Instead, do
simple test in rtl8169_set_features().
Set the RxChkSum and RxVlan through __rtl8169_set_features() in
rtl_open().
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Tue, 16 Sep 2014 00:20:42 +0000 (17:20 -0700)]
scsi: fix build errors, SCSI_FC_ATTRS needs to depend on SCSI && NET
Fix build errors when CONFIG_SCSI_NETLINK is enabled but
CONFIG_NET is not enabled:
drivers/built-in.o: In function `scsi_nl_rcv_msg':
scsi_netlink.c:(.text+0x1850fa): undefined reference to `netlink_ack'
scsi_netlink.c:(.text+0x185105): undefined reference to `skb_pull'
scsi_netlink.c:(.text+0x18515d): undefined reference to `netlink_capable'
drivers/built-in.o: In function `scsi_netlink_init':
(.text+0x185244): undefined reference to `init_net'
drivers/built-in.o: In function `scsi_netlink_init':
(.text+0x185258): undefined reference to `__netlink_kernel_create'
drivers/built-in.o: In function `scsi_netlink_exit':
(.text+0x185291): undefined reference to `netlink_kernel_release'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 15 Sep 2014 21:45:23 +0000 (17:45 -0400)]
Merge branch 'bnx2-deps'
Anish Bhatt says:
====================
net: Fix randconfig errros in bnx2i/bnx2fc caused by IPV6
Just like CNIC bnx2i/bnx2fc also have their tristate dependent on IPV6, however
using the same solution as CNIC can cause recursive dependecies during make.
Based on suggestions by Randy Dunlap, SCSI_NETLINK now depends on NET instead
of selecting NET. Second patch fixes the actual randconfig error.
Entire thread can be followed here : https://lkml.org/lkml/2014/9/9/500
Fixes:
c99d667e8527 ("cnic : Cleanup CONFIG_IPV6 & VLAN check")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Anish Bhatt [Mon, 15 Sep 2014 20:45:21 +0000 (13:45 -0700)]
bnx2i/bnx2fc : fix randconfig error in next-
20140909
Just like CNIC, tristate of these two modules is also dependent on IPV6.
These need to be handled separately as they select CNIC, which can override
tristate for CNIC from 'm' to 'y', which can cause build failures when ipv6 is
compiled as a module even if CNIC's Kconfig will only 'm' or 'n' when ipv6 is
compiled as a module.
Fixes:
c99d667e8527 ("cnic : Cleanup CONFIG_IPV6 & VLAN check")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anish Bhatt [Mon, 15 Sep 2014 20:45:20 +0000 (13:45 -0700)]
scsi_netlink : Make SCSI_NETLINK dependent on NET instead of selecting NET
Required for avoiding recursive dependencies in the Kconfig, brought out
by fixing randconfig error for bnx2i/bnx2fc in the patch that follows.
As suggested by Randy Dunlap
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Mon, 15 Sep 2014 21:28:46 +0000 (02:58 +0530)]
cxgb4: Don't allocate adapter structure for all PF's
commit
35b1de557970 ("rdma/cxgb4: Fixes cxgb4 probe failure in VM when PF is
exposed through PCI Passthrough") moved the code to check for SR-IOV PF[0..3]
much further down in init_one() past the point where we allocate a (struct
adapter) for PF[0..3]. As a result, we left four of these on ever module remove.
Fix: Allocate adapter structure only for PF4
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Mon, 15 Sep 2014 19:24:26 +0000 (15:24 -0400)]
bridge: Fix br_should_learn to check vlan_enabled
As Toshiaki Makita pointed out, the BRIDGE_INPUT_SKB_CB will
not be initialized in br_should_learn() as that function
is called only from br_handle_local_finish(). That is
an input handler for link-local ethernet traffic so it perfectly
correct to check br->vlan_enabled here.
Reported-by: Toshiaki Makita<toshiaki.makita1@gmail.com>
Fixes:
20adfa1 bridge: Check if vlan filtering is enabled only once.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Y. Fomichev [Mon, 15 Sep 2014 10:22:35 +0000 (14:22 +0400)]
net: fix creation adjacent device symlinks
__netdev_adjacent_dev_insert may add adjust device of different net
namespace, without proper check it leads to emergence of broken
sysfs links from/to devices in another namespace.
Fix: rewrite netdev_adjacent_is_neigh_list macro as a function,
move net_eq check into netdev_adjacent_is_neigh_list.
(thanks David)
related to:
4c75431ac3520631f1d9e74aa88407e6374dbbc4
Signed-off-by: Alexander Fomichev <git.user@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Looijmans [Mon, 15 Sep 2014 10:06:33 +0000 (12:06 +0200)]
net/phy: micrel: Disable asymmetric pause for KSZ9031
The KSZ9031 appears to suffer from the same hardware bug as described
for the KSZ9021 in commit
32fcafbcd1c9f6c7013016a22a5369b4acb93577
("net/phy: micrel: Disable asymmetric pause for KSZ9021")
you have to unplug the cable and plug it back to get it to work.
Remove the SUPPORTED_Asym_Pause flag for the KSZ9031 to fix this.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 13 Sep 2014 21:22:02 +0000 (17:22 -0400)]
Merge branch 'bridge_vlan_filtering'
Vladislav Yasevich says:
====================
bridge: Two small fixes to vlan filtering code.
This series corrects 2 small issues that I've ran across recently
while doing more work with vlan filtering changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Fri, 12 Sep 2014 20:26:17 +0000 (16:26 -0400)]
bridge: Allow clearing of pvid and untagged bitmap
Currently, it is possible to modify the vlan filter
configuration to add pvid or untagged support.
For example:
bridge vlan add vid 10 dev eth0
bridge vlan add vid 10 dev eth0 untagged pvid
The second statement will modify vlan 10 to
include untagged and pvid configuration.
However, it is currently impossible to go backwards
bridge vlan add vid 10 dev eth0 untagged pvid
bridge vlan add vid 10 dev eth0
Here nothing happens. This patch correct this so
that any modifiers not supplied are removed from
the configuration.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Fri, 12 Sep 2014 20:26:16 +0000 (16:26 -0400)]
bridge: Check if vlan filtering is enabled only once.
The bridge code checks if vlan filtering is enabled on both
ingress and egress. When the state flip happens, it
is possible for the bridge to currently be forwarding packets
and forwarding behavior becomes non-deterministic. Bridge
may drop packets on some interfaces, but not others.
This patch solves this by caching the filtered state of the
packet into skb_cb on ingress. The skb_cb is guaranteed to
not be over-written between the time packet entres bridge
forwarding path and the time it leaves it. On egress, we
can then check the cached state to see if we need to
apply filtering information.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Fri, 12 Sep 2014 15:38:18 +0000 (17:38 +0200)]
bonding: fix div by zero while enslaving and transmitting
The problem is that the slave is first linked and slave_cnt is
incremented afterwards leading to a div by zero in the modes that use it
as a modulus. What happens is that in bond_start_xmit()
bond_has_slaves() is used to evaluate further transmission and it becomes
true after the slave is linked in, but when slave_cnt is used in the xmit
path it is still 0, so fetch it once and transmit based on that. Since
it is used only in round-robin and XOR modes, the fix is only for them.
Thanks to Eric Dumazet for pointing out the fault in my first try to fix
this.
Call trace (took it out of net-next kernel, but it's the same with net):
[46934.330038] divide error: 0000 [#1] SMP
[46934.330041] Modules linked in: bonding(O) 9p fscache
snd_hda_codec_generic crct10dif_pclmul
[46934.330041] bond0: Enslaving eth1 as an active interface with an up
link
[46934.330051] ppdev joydev crc32_pclmul crc32c_intel 9pnet_virtio
ghash_clmulni_intel snd_hda_intel 9pnet snd_hda_controller parport_pc
serio_raw pcspkr snd_hda_codec parport virtio_balloon virtio_console
snd_hwdep snd_pcm pvpanic i2c_piix4 snd_timer i2ccore snd soundcore
virtio_blk virtio_net virtio_pci virtio_ring virtio ata_generic
pata_acpi floppy [last unloaded: bonding]
[46934.330053] CPU: 1 PID: 3382 Comm: ping Tainted: G O
3.17.0-rc4+ #27
[46934.330053] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[46934.330054] task:
ffff88005aebf2c0 ti:
ffff88005b728000 task.ti:
ffff88005b728000
[46934.330059] RIP: 0010:[<
ffffffffa0198c33>] [<
ffffffffa0198c33>]
bond_start_xmit+0x1c3/0x450 [bonding]
[46934.330060] RSP: 0018:
ffff88005b72b7f8 EFLAGS:
00010246
[46934.330060] RAX:
0000000000000679 RBX:
ffff88004b077000 RCX:
000000000000002a
[46934.330061] RDX:
0000000000000000 RSI:
ffff88004b3f0500 RDI:
ffff88004b077940
[46934.330061] RBP:
ffff88005b72b830 R08:
00000000000000c0 R09:
ffff88004a83e000
[46934.330062] R10:
000000000000ffff R11:
ffff88004b1f12c0 R12:
ffff88004b3f0500
[46934.330062] R13:
ffff88004b3f0500 R14:
000000000000002a R15:
ffff88004b077940
[46934.330063] FS:
00007fbd91a4c740(0000) GS:
ffff88005f080000(0000)
knlGS:
0000000000000000
[46934.330064] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[46934.330064] CR2:
00007f803a8bb000 CR3:
000000004b2c9000 CR4:
00000000000406e0
[46934.330069] Stack:
[46934.330071]
ffffffff811e6169 00000000e772fa05 ffff88004b077000
ffff88004b3f0500
[46934.330072]
ffffffff81d17d18 000000000000002a 0000000000000000
ffff88005b72b8a0
[46934.330073]
ffffffff81620108 ffffffff8161fe0e ffff88005b72b8c4
ffff88005b302000
[46934.330073] Call Trace:
[46934.330077] [<
ffffffff811e6169>] ?
__kmalloc_node_track_caller+0x119/0x300
[46934.330084] [<
ffffffff81620108>] dev_hard_start_xmit+0x188/0x410
[46934.330086] [<
ffffffff8161fe0e>] ? harmonize_features+0x2e/0x90
[46934.330088] [<
ffffffff81620b06>] __dev_queue_xmit+0x456/0x590
[46934.330089] [<
ffffffff81620c50>] dev_queue_xmit+0x10/0x20
[46934.330090] [<
ffffffff8168f022>] arp_xmit+0x22/0x60
[46934.330091] [<
ffffffff8168f090>] arp_send.part.16+0x30/0x40
[46934.330092] [<
ffffffff8168f1e5>] arp_solicit+0x115/0x2b0
[46934.330094] [<
ffffffff8160b5d7>] ? copy_skb_header+0x17/0xa0
[46934.330096] [<
ffffffff8162875a>] neigh_probe+0x4a/0x70
[46934.330097] [<
ffffffff8162979c>] __neigh_event_send+0xac/0x230
[46934.330098] [<
ffffffff8162a00b>] neigh_resolve_output+0x13b/0x220
[46934.330100] [<
ffffffff8165f120>] ? ip_forward_options+0x1c0/0x1c0
[46934.330101] [<
ffffffff81660478>] ip_finish_output+0x1f8/0x860
[46934.330102] [<
ffffffff81661f08>] ip_output+0x58/0x90
[46934.330103] [<
ffffffff81661602>] ? __ip_local_out+0xa2/0xb0
[46934.330104] [<
ffffffff81661640>] ip_local_out_sk+0x30/0x40
[46934.330105] [<
ffffffff81662a66>] ip_send_skb+0x16/0x50
[46934.330106] [<
ffffffff81662ad3>] ip_push_pending_frames+0x33/0x40
[46934.330107] [<
ffffffff8168854c>] raw_sendmsg+0x88c/0xa30
[46934.330110] [<
ffffffff81612b31>] ? skb_recv_datagram+0x41/0x60
[46934.330111] [<
ffffffff816875a9>] ? raw_recvmsg+0xa9/0x1f0
[46934.330113] [<
ffffffff816978d4>] inet_sendmsg+0x74/0xc0
[46934.330114] [<
ffffffff81697a9b>] ? inet_recvmsg+0x8b/0xb0
[46934.330115] bond0: Adding slave eth2
[46934.330116] [<
ffffffff8160357c>] sock_sendmsg+0x9c/0xe0
[46934.330118] [<
ffffffff81603248>] ?
move_addr_to_kernel.part.20+0x28/0x80
[46934.330121] [<
ffffffff811b4477>] ? might_fault+0x47/0x50
[46934.330122] [<
ffffffff816039b9>] ___sys_sendmsg+0x3a9/0x3c0
[46934.330125] [<
ffffffff8144a14a>] ? n_tty_write+0x3aa/0x530
[46934.330127] [<
ffffffff810d1ae4>] ? __wake_up+0x44/0x50
[46934.330129] [<
ffffffff81242b38>] ? fsnotify+0x238/0x310
[46934.330130] [<
ffffffff816048a1>] __sys_sendmsg+0x51/0x90
[46934.330131] [<
ffffffff816048f2>] SyS_sendmsg+0x12/0x20
[46934.330134] [<
ffffffff81738b29>] system_call_fastpath+0x16/0x1b
[46934.330144] Code: 48 8b 10 4c 89 ee 4c 89 ff e8 aa bc ff ff 31 c0 e9
1a ff ff ff 0f 1f 00 4c 89 ee 4c 89 ff e8 65 fb ff ff 31 d2 4c 89 ee 4c
89 ff <f7> b3 64 09 00 00 e8 02 bd ff ff 31 c0 e9 f2 fe ff ff 0f 1f 00
[46934.330146] RIP [<
ffffffffa0198c33>] bond_start_xmit+0x1c3/0x450
[bonding]
[46934.330146] RSP <
ffff88005b72b7f8>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
Fixes:
278b208375 ("bonding: initial RCU conversion")
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 13 Sep 2014 20:52:52 +0000 (16:52 -0400)]
Merge branch 'r8169-net'
Hayes Wang says:
====================
r8169: fix rx vlan
There are two issues for hw rx vlan. The patches are
used to fix them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Fri, 12 Sep 2014 03:35:12 +0000 (11:35 +0800)]
r8169: fix setting rx vlan
The setting should depend on the new features not the current one.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Fri, 12 Sep 2014 03:35:11 +0000 (11:35 +0800)]
r8169: fix the default setting of rx vlan
If the parameter "features" of __rtl8169_set_features() is equal to
dev->features, the variable "changed" is alwayes 0, and nothing would
be changed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Thu, 11 Sep 2014 17:22:38 +0000 (22:52 +0530)]
drivers: net: cpsw: dual_emac: in suspend/resume bring down/up all the netdev
During suspend and resume in Dual EMAC, second port is not working as in
suspend/resume only the first slave netdev is closed and opened. So bring
down and up all the interfaces that are up during suspend/resume.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Einon [Thu, 11 Sep 2014 22:19:49 +0000 (23:19 +0100)]
drivers: net: b44: Fix typo in returning multicast stats
nstat->multicast refers to received packets, not transmitted as
is returned here. Change it so that received packet stats are
given.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 12 Sep 2014 22:21:47 +0000 (18:21 -0400)]
Merge tag 'master-2014-09-11' of git://git./linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-09-11
Please pull this batch of fixes intended for the 3.17 stream:
For the mac80211 bits, Johannes says:
"Two more fixes for mac80211 - one of them addresses a long-standing
issue that we only found when using vendor events more frequently;
the other addresses some bad information being reported in userspace
that people were starting to actually look at."
For the iwlwifi bits, Emmanuel says:
"I re-enable scheduled scan on firmware that contain the fix for
the bug that Linus reported. A few trivial fixes: endianity issues,
the same DTIM period fix that I did in mac80211. Eyal fixes a few
issues we identified with EAPOL, we now send them just as if they were
management frames, this solves interrop issues. Johannes has another
set of trivial fixes, while Luca fixes the way we configure the filters
in the firmware. Last but not least, a new device is added by Oren."
Emmanuel was traveling, resulting in his pull to be a bit larger than
I would have liked to see at this point. FWIW, I have asked Emmanuel
to be much more strict for any more pull requests in this cycle.
In addition to the above, Sujith Manoharan reverts an earlier ath9k
patch. The earlier change was found to allow for the device to sleep
too long and miss beacons.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 12 Sep 2014 22:04:04 +0000 (18:04 -0400)]
Merge tag 'linux-can-fixes-for-3.17-
20140911' of git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2014-09-11
this is a pull request for the current release cycle of a single patch.
The patch by David Jander fixes a scheduling while atomic problem in the
flexcan driver, that was introduced by me in v3.14-rc6.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Wed, 10 Sep 2014 21:23:02 +0000 (23:23 +0200)]
ipv6: clean up anycast when an interface is destroyed
If we try to rmmod the driver for an interface while sockets with
setsockopt(JOIN_ANYCAST) are alive, some refcounts aren't cleaned up
and we get stuck on:
unregister_netdevice: waiting for ens3 to become free. Usage count = 1
If we LEAVE_ANYCAST/close everything before rmmod'ing, there is no
problem.
We need to perform a cleanup similar to the one for multicast in
addrconf_ifdown(how == 1).
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 12 Sep 2014 21:18:09 +0000 (17:18 -0400)]
Merge branch 'arc_emac'
Beniamino Galvani says:
====================
net: arc_emac: fix tx issues
the patches below solve some issues found in the tx ring reclaim
strategy currently implemented in the arc_emac driver.
Without these patches a simple outgoing UDP flow blocks almost
immediately with the socket send buffer full, until some new rx
packets trigger a clean of the tx ring.
Everything seems to work fine on a Radxa Rock with this fix applied.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Beniamino Galvani [Wed, 10 Sep 2014 20:50:03 +0000 (22:50 +0200)]
net: arc_emac: prevent reuse of unreclaimed tx descriptors
This patch changes the logic in tx path to ensure that tx descriptors
are reused for transmission only after they have been reclaimed by
arc_emac_tx_clean().
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Beniamino Galvani [Wed, 10 Sep 2014 20:50:02 +0000 (22:50 +0200)]
net: arc_emac: enable tx interrupts
In the current implementation the cleaning of tx ring is done by the
NAPI poll handler, which is scheduled after rx interrupts. Thus, in
absence of received packets the reclaim of used tx buffers is never
executed, blocking further transmission.
This can be easily reproduced starting the transmission of a UDP flow
with iperf, which blocks almost immediately because skbs are not
returned to the stack and the socket send buffer becomes full.
The patch enables tx interrupts so that the tx reclaim is scheduled
after completed transmissions.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sujith Manoharan [Thu, 11 Sep 2014 13:35:48 +0000 (19:05 +0530)]
Revert "ath9k: Calculate sleep duration"
This reverts commit
09ebb810927a110e4c354beb20308830d108a54b.
ath9k_hw_set_sta_beacon_timers() configures AR_TIM_PERIOD with
the beacon interval. Before this commit, the sleepduration was
never greater than the beacon interval. But now, the behavior
has changed. For example, with an AP that uses a beacon interval of 100:
ath: phy9: next beacon
61128704
ath: phy9: beacon period 204800
ath: phy9: DTIM period 204800
If the sleepduration is calculated based on the listen time, then
the bmiss threshold should also be changed since the HW would
be in sleep state for a longer time, but that is not done currently.
To avoid configuring a higher beacon interval based on the sleepduration,
revert to the original behavior. Power consumption is not a
problem since PS is disabled in ath9k anyway.
Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Jander [Wed, 27 Aug 2014 10:02:16 +0000 (12:02 +0200)]
can: flexcan: avoid calling usleep_range from interrupt context
Apparently can_restart() runs from a (timer-) interrupt and can call
flexcan_chip_[en|dis]able(), so avoid using usleep_range()
Signed-off-by: David Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Markos Chandras [Wed, 10 Sep 2014 13:51:44 +0000 (14:51 +0100)]
Documentation: filter: Add MIPS to architectures with BPF JIT
MIPS supports BPF JIT since v3.16-rc1
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Wed, 10 Sep 2014 14:15:11 +0000 (17:15 +0300)]
mlx4: Fix wrong endianess access with QP context flags
We wrongly tested QP context bits without BE conversion
as was spotted by sparse...
drivers/infiniband/hw/mlx4/qp.c:1685:38: sparse: restricted __be32 degrades to integer
Fix that!
Fixes:
d2fce8a ('mlx4: Set user-space raw Ethernet QPs to properly handle VXLAN traffic')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 10 Sep 2014 22:21:38 +0000 (15:21 -0700)]
Merge branch 'mlx4'
Or Gerlitz says:
====================
mlx4 SRIOV fixes
This series contains few SRIOV related fixes from Matan, please apply to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Wed, 10 Sep 2014 13:41:56 +0000 (16:41 +0300)]
net/mlx4: Set vlan stripping policy by the right command
Changing the vlan stripping policy of the QP isn't supported by older
firmware versions for the INIT2RTR command. Nevertheless, we've used it.
Fix that by doing this policy change using INIT2RTR only if the firmware
supports it, otherwise, we call UPDATE_QP command to do the task.
Fixes:
7677fc9 ('net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Wed, 10 Sep 2014 13:41:55 +0000 (16:41 +0300)]
net/mlx4: Avoid dealing with MAC index in UPDATE_QP wrapper if not needed
The current wrapper implementation of the UPDATE_QP command tries to get
the MAC index, even if MAC wasn't set by the VF. Fix it up to only handle
the MAC field if it's valid.
Fixes:
ce8d9e0 ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Wed, 10 Sep 2014 13:41:54 +0000 (16:41 +0300)]
net/mlx4: Use the correct VSD mask in UPDATE_QP
When doing VGT->VST->VGT state changes, we used an incorrect mask
for the vlan-stripping-disable (VSD) flag, hence the vlan related policy
for user-space Raw Ethernet QPs open by VFs wasn't really applied.
Fix that, by using the correct mask.
Fixes:
f0f829b ('net/mlx4_core: Add immediate activate for VGT->VST->VGT')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Wed, 10 Sep 2014 13:41:53 +0000 (16:41 +0300)]
net/mlx4: Correctly configure single ported VFs from the host
Single port VFs are seen PCI wise on both ports of the PF (we don't have
single port PFs with ConnectX). With this in mind, it's possible for
virtualization tools to try and configure a single ported VF through
the "wrong" PF port.
To handle that, we use the PF driver mapping of single port VFs to NIC
ports and adjust the port value before calling into the low level
code that does the actual VF configuration
Fixes:
449fc48 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Wed, 10 Sep 2014 11:08:09 +0000 (16:38 +0530)]
drivers: net: cpsw: dual_emac: fix reducing of rx descriptor during ifdown
In Dual EMAC, when both interface are up and while doing ifdown with heavy
traffic then skbs already processed by DMA from that slave emac has to be
requeued as still the other interface is up and running.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Tue, 9 Sep 2014 14:19:44 +0000 (15:19 +0100)]
RxRPC: Fix missing __user annotation
Fix a missing __user annotation in a cast of a user space pointer (found by
checker).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Masanari Iida [Tue, 9 Sep 2014 09:07:55 +0000 (18:07 +0900)]
net:bonding: Add missing space in bonding driver parameter description
This patch adds missing space between "interface" and "by"
in bonding module parameter description.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ani Sinha [Mon, 8 Sep 2014 21:49:59 +0000 (14:49 -0700)]
net:socket: set msg_namelen to 0 if msg_name is passed as NULL in msghdr struct from userland.
Linux manpage for recvmsg and sendmsg calls does not explicitly mention setting msg_namelen to 0 when
msg_name passed set as NULL. When developers don't set msg_namelen member in msghdr, it might contain garbage
value which will fail the validation check and sendmsg and recvmsg calls from kernel will return EINVAL. This will
break old binaries and any code for which there is no access to source code.
To fix this, we set msg_namelen to 0 when msg_name is passed as NULL from userland.
Signed-off-by: Ani Sinha <ani@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville [Tue, 9 Sep 2014 19:00:06 +0000 (15:00 -0400)]
Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-fixes
John W. Linville [Tue, 9 Sep 2014 18:29:36 +0000 (14:29 -0400)]
Merge tag 'mac80211-for-john-2014-09-08' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg <johannes@sipsolutions.net> says:
"Two more fixes for mac80211 - one of them addresses a long-standing
issue that we only found when using vendor events more frequently;
the other addresses some bad information being reported in userspace
that people were starting to actually look at."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
David S. Miller [Mon, 8 Sep 2014 23:02:59 +0000 (16:02 -0700)]
Merge branch 'oom_fixes'
Florian Fainelli says:
====================
net: systemport and bcmgenet OOM fixes
These two patches fix similar Out of Memory code paths in the SYSTEMPORT and
GENET drivers. Under high memory pressure, we could produce an OOPS by
passing a NULL pointer to dma_unmap_single().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 8 Sep 2014 18:37:52 +0000 (11:37 -0700)]
net: bcmgenet: check harder for out of memory conditions
There is a potential case where we might be failing to refill a
control block, leaving it with both a NULL skb pointer *and* a NULL
dma_unmap_addr.
The way we process incoming packets, by first calling
dma_unmap_single(), and then only checking for a potential NULL skb can
lead to situations where do pass a NULL dma_unmap_addr() to
dma_unmap_single(), resulting in an oops.
Fix this my moving the NULL skb check earlier, since no backing skb
also means no corresponding DMA mapping for this packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 8 Sep 2014 18:37:51 +0000 (11:37 -0700)]
net: systemport: check harder for out of memory conditions
There is a potential case where we might be failing to refill a
control block, leaving it with both a NULL skb pointer *and* a NULL
dma_unmap_addr.
The way we process incoming packets, by first calling
dma_unmap_single(), and then only checking for a potential NULL skb can
lead to situations where do pass a NULL dma_unmap_addr() to
dma_unmap_single(), resulting in an oops.
Fix this my moving the NULL skb check earlier, since no backing skb
also means no corresponding DMA mapping for this packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Mon, 8 Sep 2014 16:46:53 +0000 (18:46 +0200)]
net/mlx4_en: do not ignore autoneg in mlx4_en_set_pauseparam()
The driver does not support pause autonegotiation so it should return
-EINVAL when the function is called with non-zero autoneg.
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aaro Koskinen [Mon, 8 Sep 2014 15:01:53 +0000 (18:01 +0300)]
drivers: net: ethernet: octeon_mgmt: fix a compiler warning
Fix the following compiler warning:
drivers/net/ethernet/octeon/octeon_mgmt.c: In function 'octeon_mgmt_clean_tx_buffers':
drivers/net/ethernet/octeon/octeon_mgmt.c:295:4: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
u64 ns = cvmx_read_csr(CVMX_MIXX_TSTAMP(p->port));
^
Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 8 Sep 2014 11:00:00 +0000 (04:00 -0700)]
net: fix skb_page_frag_refill() kerneldoc
In commit
d9b2938aabf7 ("net: attempt a single high order allocation)
I forgot to update kerneldoc, as @prio parameter was renamed to @gfp
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David L Stevens [Mon, 8 Sep 2014 20:23:01 +0000 (16:23 -0400)]
sunvnet - add missing rmb() for sunvnet driver
The sunvnet driver does not have an rmb() in the ring consumer corresponding
to the wmb() in the producer. According to Documentation/memory-barriers.txt:
"When dealing with CPU-CPU interactions, certain types of memory barrier should
always be paired. A lack of appropriate pairing is almost certainly an error."
In cases where an rmb() is not a no-op and a consumer is removing data from
the ring while a producer is adding new entries, a load reorder would allow
CPU1 CPU2
---- ----
LOAD desc.size [e.g]
STORE desc.size
<wmb>
set desc.hdr.state = VIO_DESC_READY
LOAD desc.hdr.state
[because VIO_DESC_READY, use
old desc.size, already loaded
out of order]
[CPU2 has reordered apparently unrelated LOADs]
To ensure other desc fields are not loaded before checking VIO_DESC_READY, we
need an rmb() between the check and desc data accesses.
I've also moved the viodbg() call to after the rmb() so that it, too, has
current descriptor data even with reordering, which has the side effect that
it won't print anything for descriptors that are not VIO_DESC_READY as before.
That's a) probably a good thing, since the fields are not necessarily set and,
b) better than adding another rmb() just for viodbg().
This would not be possible if strict-ordering is enforced, but then the
memory barriers should be no-ops in that case.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eyal Shapira [Tue, 12 Aug 2014 21:26:17 +0000 (00:26 +0300)]
iwlwifi: mvm: fix an overflow in iwl_mvm_get_signal_strength
The idea here is to translate a value of 0 received from
the firmware to the lowest rssi figure. As rx_status->chain_signal
is a signed byte the lowest possible value is -128 and not -256.
-256 was causing 0 to get stored in the signed byte.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Oren Givon [Mon, 8 Sep 2014 05:57:05 +0000 (08:57 +0300)]
iwlwifi: add PCI IDs and add then new 3165 series
This change does the following:
1) Add a new 7265 series PCI ID
2) Add two new 3160 series PCI IDs
3) Add the new 3165 series PCI IDs and configurations
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Linus Torvalds [Mon, 8 Sep 2014 15:27:00 +0000 (08:27 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A bug fix for the vdso code, the loadparm for booting from SCSI is
added and the access permissions for the dasd module parameters are
corrected"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/vdso: remove NULL pointer check from clock_gettime
s390/ipl: Add missing SCSI loadparm attributes to /sys/firmware
s390/dasd: Make module parameter visible in sysfs
Emmanuel Grumbach [Sun, 7 Sep 2014 18:33:53 +0000 (21:33 +0300)]
iwlwifi: dvm: disable power save by default
In
https://bugzilla.kernel.org/show_bug.cgi?id=84031,
the submitter said that disabling power saving helped,
do just that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Johannes Berg [Thu, 21 Aug 2014 17:08:44 +0000 (19:08 +0200)]
iwlwifi: mvm: BT Coex - always initialize smps_mode
smps_mode is used uninitialized in a debug statement in AP
mode, so always initialize it.
While at it, fix a typo.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Emmanuel Grumbach [Thu, 31 Jul 2014 11:39:40 +0000 (14:39 +0300)]
iwlwiwi: mvm: use bss_conf->dtim_period instead of conf.ps_dtim_period
The latter is meant for software implementation of power
save and is not per-virtual interface. Since our driver
supports multiple virtual interfaces, we need to use
vif->bss_conf.dtim_period.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eyal Shapira [Tue, 2 Sep 2014 15:39:21 +0000 (18:39 +0300)]
iwlwifi: mvm: treat EAPOLs like mgmt frames wrt rate
Using the LQ table which is initially set according to
the rssi could lead to EAPOLs being sent in high legacy
rates like 54mbps.
It's better to avoid sending EAPOLs in high rates as it reduces
the chances of a successful 4-Way handshake.
Avoid this and treat them like other mgmt frames which would
initially get sent at the basic rate.
Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Johannes Berg [Tue, 26 Aug 2014 12:25:46 +0000 (14:25 +0200)]
iwlwifi: mvm: correctly handle PM/QoS changes from mac80211
When mac80211 requests multiple BSS config changes, as for example
while associating, we ignore power management and QoS changes and
only apply them later. Fix that by removing the "else" and making
the conditions independent.
Also move it after (potential) beacon filter enablement to have
that already enabled when going into power management code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eliad Peller [Tue, 26 Aug 2014 08:23:11 +0000 (11:23 +0300)]
iwlwifi: increase DEFAULT_MAX_TX_POWER
The chip is able to transmit up to 22dBm, so set
the constant appropriately.
CC: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Emmanuel Grumbach [Thu, 31 Jul 2014 11:32:37 +0000 (14:32 +0300)]
iwlwifi: mvm: fix endianity issues with Smart Fifo commands
This code was broken on big endian systems. Sparse didn't
catch the bug since the firmware command was not tagged as
little endian.
Fix the bug for big endian systems and tag the field in the
firmware command to prevent such issues in the future.
Cc: stable@vger.kernel.org [3.14+]
Fixes:
1f3b0ff8ec ("iwlwifi: mvm: Add Smart FIFO support")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Luciano Coelho [Wed, 30 Jul 2014 12:04:08 +0000 (15:04 +0300)]
iwlwifi: mvm: set MAC_FILTER_IN_BEACON correctly for STA/P2P client
In commit
cad3f08c (iwlwifi: mvm: enable MAC_FILTER_IN_BEACON when
forced_assoc_off is set) the code to set the MAC_FILTER_IN_BEACON flag
was accidentally moved to the main block of the if statement, while it
should be in the else block instead. Move it to the right place.
Fixes:
cad3f08c23de ("iwlwifi: mvm: enable MAC_FILTER_IN_BEACON when forced_assoc_off is set")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Johannes Berg [Fri, 25 Jul 2014 12:49:59 +0000 (14:49 +0200)]
iwlwifi: mvm: BT Coex - remove shadowing variable
The variable 'u32 mode' exists twice, the latter shadowing
the former - remove the latter since there's no need for
two variables.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Linus Torvalds [Mon, 8 Sep 2014 03:20:16 +0000 (20:20 -0700)]
Merge branch 'for-3.17-fixes' of git://git./linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"This pull request includes Alban's patch to disallow '\n' in cgroup
names.
Two other patches from Li to fix a possible oops when cgroup
destruction races against other file operations and one from Vivek to
fix a unified hierarchy devel behavior"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: check cgroup liveliness before unbreaking kernfs
cgroup: delay the clearing of cgrp->kn->priv
cgroup: Display legacy cgroup files on default hierarchy
cgroup: reject cgroup names with '\n'
Linus Torvalds [Mon, 8 Sep 2014 03:10:06 +0000 (20:10 -0700)]
Merge branch 'for-3.17-fixes' of git://git./linux/kernel/git/tj/percpu
Pull percpu fixes from Tejun Heo:
"One patch to fix a failure path in the alloc path. The bug is
dangerous but probably not too likely to actually trigger in the wild
given that there hasn't been any report yet.
The other two are low impact fixes"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: free percpu allocation info for uniprocessor system
percpu: perform tlb flush after pcpu_map_pages() failure
percpu: fix pcpu_alloc_pages() failure path
Linus Torvalds [Mon, 8 Sep 2014 03:06:44 +0000 (20:06 -0700)]
Merge branch 'for-3.17-fixes' of git://git./linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Two patches are to add PCI IDs for ICH9 and all others are device
specific fixes. Nothing too interesting"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci_xgene: Fix the link down in first attempt for the APM X-Gene SoC AHCI SATA host controller driver.
ahci_xgene: Skip the PHY and clock initialization if already configured by the firmware.
ahci: add pcid for Marvel 0x9182 controller
ata: Disabling the async PM for JMicron chip 363/361
ata_piix: Add Device IDs for Intel 9 Series PCH
ahci: Add Device IDs for Intel 9 Series PCH
ata: ahci_tegra: Read calibration fuse
Linus Torvalds [Mon, 8 Sep 2014 02:56:38 +0000 (19:56 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix skb leak in mac802154, from Martin Townsend
2) Use select not depends on NF_NAT for NFT_NAT, from Pablo Neira
Ayuso
3) Fix union initializer bogosity in vxlan, from Gerhard Stenzel
4) Fix RX checksum configuration in stmmac driver, from Giuseppe
CAVALLARO
5) Fix TSO with non-accelerated VLANs in e1000, e1000e, bna, ehea,
i40e, i40evf, mvneta, and qlge, from Vlad Yasevich
6) Fix capability checks in phy_init_eee(), from Giuseppe CAVALLARO
7) Try high order allocations more sanely for SKBs, specifically if a
high order allocation fails, fall back directly to zero order pages
rather than iterating down one order at a time. From Eric Dumazet
8) Fix a memory leak in openvswitch, from Li RongQing
9) amd-xgbe initializes wrong spinlock, from Thomas Lendacky
10) RTNL locking was busted in setsockopt for anycast and multicast, fix
from Sabrina Dubroca
11) Fix peer address refcount leak in ipv6, from Nicolas Dichtel
12) DocBook typo fixes, from Masanari Iida
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
ipv6: restore the behavior of ipv6_sock_ac_drop()
amd-xgbe: Enable interrupts for all management counters
amd-xgbe: Treat certain counter registers as 64 bit
greth: moved TX ring cleaning to NAPI rx poll func
cnic : Cleanup CONFIG_IPV6 & VLAN check
net: treewide: Fix typo found in DocBook/networking.xml
bnx2x: Fix link problems for 1G SFP RJ45 module
3c59x: avoid panic in boomerang_start_xmit when finding page address:
netfilter: add explicit Kconfig for NETFILTER_XT_NAT
ipv6: use addrconf_get_prefix_route() to remove peer addr
ipv6: fix a refcnt leak with peer addr
net-timestamp: only report sw timestamp if reporting bit is set
drivers/net/fddi/skfp/h/skfbi.h: Remove useless PCI_BASE_2ND macros
l2tp: fix race while getting PMTU on PPP pseudo-wire
ipv6: fix rtnl locking in setsockopt for anycast and multicast
VMXNET3: Check for map error in vmxnet3_set_mc
openvswitch: distinguish between the dropped and consumed skb
amd-xgbe: Fix initialization of the wrong spin lock
openvswitch: fix a memory leak
netfilter: fix missing dependencies in NETFILTER_XT_TARGET_LOG
...
David S. Miller [Sun, 7 Sep 2014 23:11:10 +0000 (16:11 -0700)]
Merge tag 'master-2014-09-04' of git://git./linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-09-05
Please pull this batch of fixes intended for the 3.17 stream...
For the mac80211 bits, Johannes says:
"Here are a few fixes for mac80211. One has been discussed for a while
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs."
For the iwlwifi bits, Emmanuel says:
"I revert a patch that disabled CTS to self in dvm because users
reported issues. The revert is CCed to stable since the offending
patch was sent to stable too. I also bump the firmware API versions
since a new firmware is coming up. On top of that, Marcel fixes a
bug I introduced while fixing a bug in our Kconfig file."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Fri, 5 Sep 2014 21:33:00 +0000 (14:33 -0700)]
ipv6: restore the behavior of ipv6_sock_ac_drop()
It is possible that the interface is already gone after joining
the list of anycast on this interface as we don't hold a refcount
for the device, in this case we are safe to ignore the error.
What's more important, for API compatibility we should not
change this behavior for applications even if it were correct.
Fixes: commit
a9ed4a2986e13011 ("ipv6: fix rtnl locking in setsockopt for anycast and multicast")
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 7 Sep 2014 23:09:43 +0000 (16:09 -0700)]
Linux 3.17-rc4
Sudip Mukherjee [Sun, 7 Sep 2014 18:26:12 +0000 (11:26 -0700)]
Documentation: new page link in SubmittingPatches
new link for - How to piss off a Linux kernel subsystem maintainer
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Bolle [Sun, 7 Sep 2014 18:25:55 +0000 (11:25 -0700)]
Documentation: NFS/RDMA: Document separate Kconfig symbols
The NFS/RDMA Kconfig symbol was split into separate options for client
and server in commit
2e8c12e1b765 ("xprtrdma: add separate Kconfig
options for NFSoRDMA client and server support").
Update the documentation to reflect this split.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "J. Bruce Fields" <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Masanari Iida [Sun, 7 Sep 2014 18:25:45 +0000 (11:25 -0700)]
Documentation: misc-devices: Rename freefall.c from hpfall.c in lis2lv02d
hpfall.c was renamed to freefall.c in 3.16, but this file still refer to
hpfall.c instead of freefall.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jose Manuel Alarcon Roldan [Sun, 7 Sep 2014 18:25:00 +0000 (11:25 -0700)]
Documentation: i2c: rename variable "register" to "reg"
The example code provided with the i2c device interface documentation
won't compile since it uses the reserved word "register" to name a
variable.
The compiler fails with this error message:
error: expected identifier or '(' before '=' token
__u8 register = 0x20; /* Device register to access */
^
Rename the variable "register" to simply "reg" in the example code.
Another couple of typos has been fixed as well.
[Change "! =" to "!=".]
Signed-off-by: Jose Alarcon Roldan <jose.alarcon.roldan@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rob Jones [Sun, 7 Sep 2014 18:24:40 +0000 (11:24 -0700)]
Documentation: seq_file: Document seq_open_private(), seq_release_private()
Despite the fact that these functions have been around for years, they
are little used (only 15 uses in 13 files at the preseht time) even
though many other files use work-arounds to achieve the same result.
By documenting them, hopefully they will become more widely used.
Signed-off-by: Rob Jones <rob.jones@codethink.co.uk>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 7 Sep 2014 18:57:27 +0000 (11:57 -0700)]
Merge tag 'pm+acpi-3.17-rc4' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are regression fixes (ACPI sysfs, ACPI video, suspend test),
ACPI cpuidle deadlock fix, missing runtime validation of ACPI _DSD
output, a fix and a new CPU ID for the RAPL driver, new blacklist
entry for the ACPI EC driver and a couple of trivial cleanups
(intel_pstate and generic PM domains).
Specifics:
- Fix for recently broken test_suspend= command line argument (Rafael
Wysocki).
- Fixes for regressions related to the ACPI video driver caused by
switching the default to native backlight handling in 3.16 from
Hans de Goede.
- Fix for a sysfs attribute of ACPI device objects that returns stale
values sometimes due to the fact that they are cached instead of
executing the appropriate method (_SUN) every time (broken in
3.14). From Yasuaki Ishimatsu.
- Fix for a deadlock between cpuidle_lock and cpu_hotplug.lock in the
ACPI processor driver from Jiri Kosina.
- Runtime output validation for the ACPI _DSD device configuration
object missing from the support for it that has been introduced
recently. From Mika Westerberg.
- Fix for an unuseful and misleading RAPL (Running Average Power
Limit) domain detection message in the RAPL driver from Jacob Pan.
- New Intel Haswell CPU ID for the RAPL driver from Jason Baron.
- New Clevo W350etq blacklist entry for the ACPI EC driver from Lan
Tianyu.
- Cleanup for the intel_pstate driver and the core generic PM domains
code from Gabriele Mazzotta and Geert Uytterhoeven"
* tag 'pm+acpi-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / cpuidle: fix deadlock between cpuidle_lock and cpu_hotplug.lock
ACPI / scan: not cache _SUN value in struct acpi_device_pnp
cpufreq: intel_pstate: Remove unneeded variable
powercap / RAPL: change domain detection message
powercap / RAPL: add support for CPU model 0x3f
PM / domains: Make generic_pm_domain.name const
PM / sleep: Fix test_suspend= command line option
ACPI / EC: Add msi quirk for Clevo W350etq
ACPI / video: Disable native_backlight on HP ENVY 15 Notebook PC
ACPI / video: Add a disable_native_backlight quirk
ACPI / video: Fix use_native_backlight selection logic
ACPICA: ACPI 5.1: Add support for runtime validation of _DSD package.
Linus Torvalds [Sun, 7 Sep 2014 17:59:58 +0000 (10:59 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull filesystem fixes from Al Viro:
"Several bugfixes (all of them -stable fodder).
Alexey's one deals with double mutex_lock() in UFS (apparently, nobody
has tried to test "ufs: sb mutex merge + mutex_destroy" on something
like file creation/removal on ufs). Mine deal with two kinds of
umount bugs, in umount propagation and in handling of automounted
submounts, both resulting in bogus transient EBUSY from umount"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ufs: fix deadlocks introduced by sb mutex merge
fix EBUSY on umount() from MNT_SHRINKABLE
get rid of propagate_umount() mistakenly treating slaves as busy.
Linus Torvalds [Sun, 7 Sep 2014 17:51:42 +0000 (10:51 -0700)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull RCU fix from Ingo Molnar:
"A boot hang fix for the offloaded callback RCU model (RCU_NOCB_CPU=y
&& (TREE_CPU=y || TREE_PREEMPT_RC)) in certain bootup scenarios"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Make nocb leader kthreads process pending callbacks after spawning
Linus Torvalds [Sun, 7 Sep 2014 17:37:48 +0000 (10:37 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Three fixlets from the timer departement:
- Update the timekeeper before updating vsyscall and pvclock. This
fixes the kvm-clock regression reported by Chris and Paolo.
- Use the proper irq work interface from NMI. This fixes the
regression reported by Catalin and Dave.
- Clarify the compat_nanosleep error handling mechanism to avoid
future confusion"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Update timekeeper before updating vsyscall and pvclock
compat: nanosleep: Clarify error handling
nohz: Restore NMI safe local irq work for local nohz kick
Alexey Khoroshilov [Tue, 2 Sep 2014 07:40:17 +0000 (11:40 +0400)]
ufs: fix deadlocks introduced by sb mutex merge
Commit
0244756edc4b ("ufs: sb mutex merge + mutex_destroy") introduces
deadlocks in ufs_new_inode() and ufs_free_inode().
Most callers of that functions acqure the mutex by themselves and
ufs_{new,free}_inode() do that via lock_ufs(),
i.e we have an unavoidable double lock.
The patch proposes to resolve the issue by making sure that
ufs_{new,free}_inode() are not called with the mutex held.
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sat, 6 Sep 2014 23:42:12 +0000 (16:42 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"A smattering of bug fixes across most architectures"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
powerpc/kvm/cma: Fix panic introduces by signed shift operation
KVM: s390/mm: Fix guest storage key corruption in ptep_set_access_flags
KVM: s390/mm: Fix storage key corruption during swapping
arm/arm64: KVM: Complete WFI/WFE instructions
ARM/ARM64: KVM: Nuke Hyp-mode tlbs before enabling MMU
KVM: s390/mm: try a cow on read only pages for key ops
KVM: s390: Fix user triggerable bug in dead code
Linus Torvalds [Sat, 6 Sep 2014 19:37:43 +0000 (12:37 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"Another round of fixes from arm-soc land, which are mostly DT fixes
for:
- OMAP: handful of DT fixes devices on newly supported hardware
- davinci: fix 2nd EDMA channel
- ux500: extend previous pinctrl fix to another board
- at91: clock registration fixes, compatibility string precision
And one more fix for event cleanup in drivers/bus/arm-ccn"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
bus: arm-ccn: Move event cleanup routine
ARM: at91/dt: rm9200: fix usb clock definition
ARM: at91: rm9200: fix clock registration
ARM: at91/dt: sam9g20: set at91sam9g20 pllb driver
ARM: dts: dra7-evm: Add vtt regulator support
ARM: dts: dra7-evm: Fix spi1 mux documentation
ARM: dts: am43x-epos-evm: Disable QSPI to prevent conflict with GPMC-NAND
ARM: OMAP2+: gpmc: Don't complain if wait pin is used without r/w monitoring
ARM: dts: am43xx-epos-evm: Don't use read/write wait monitoring
ARM: dts: am437x-gp-evm: Don't use read/write wait monitoring
ARM: dts: am437x-gp-evm: Use BCH16 ECC scheme instead of BCH8
ARM: dts: am43x-epos-evm: Use BCH16 ECC scheme instead of BCH8
ARM: dts: am4372: fix USB regs size
ARM: dts: am437x-gp: switch i2c0 to 100KHz
ARM: dts: dra7-evm: Fix 8th NAND partition's name
ARM: dts: dra7-evm: Fix i2c3 pinmux and frequency
ARM: ux500: disable msp2 node on Snowball
ARM: edma: Fix configuration parsing for SoCs with multiple eDMA3 CC
ARM: dts: set 'ti,set-rate-parent' for dpll4_m5x2 clock
Linus Torvalds [Sat, 6 Sep 2014 19:13:17 +0000 (12:13 -0700)]
Merge tag 'xfs-for-linus-3.17-rc3' of git://git./linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"The fixes all address recently discovered data corruption issues.
The original Direct IO issue was discovered by Chris Mason @ Facebook
on a production workload which mixed buffered reads with direct reads
and writes IO to the same file. The fix for that exposed other issues
with page invalidation (exposed by millions of fsx operations) failing
due to dirty buffers beyond EOF.
Finally, the collapse_range code could also cause problems due to
racing writeback changing the extent map while it was being shifted
around. The commits for that problem are simple mitigation fixes that
prevent the problem from occuring. A more robust fix for 3.18 that
addresses the underlying problem is currently being worked on by
Brian.
Summary of fixes:
- a direct IO read/buffered read data corruption
- the associated fallout from the DIO data corruption fix
- collapse range bugs that are potential data corruption issues"
* tag 'xfs-for-linus-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: trim eofblocks before collapse range
xfs: xfs_file_collapse_range is delalloc challenged
xfs: don't log inode unless extent shift makes extent modifications
xfs: use ranged writeback and invalidation for direct IO
xfs: don't zero partial page cache pages during O_DIRECT writes
xfs: don't zero partial page cache pages during O_DIRECT writes
xfs: don't dirty buffers beyond EOF
Linus Torvalds [Sat, 6 Sep 2014 19:12:09 +0000 (12:12 -0700)]
Merge tag 'for-linus-
20140905' of git://git.infradead.org/linux-mtd
Pull mtd fixes from Brian Norris:
"Two trivial MTD updates for 3.17-rc4:
- a tiny comment tweak, to kill a bunch of DocBook warnings added
during the merge window
- a small fixup to the OTP routines' error handling"
* tag 'for-linus-
20140905' of git://git.infradead.org/linux-mtd:
mtd: nand: fix DocBook warnings on nand_sdr_timings doc
mtd: cfi_cmdset_0002: check return code for get_chip()
Thomas Gleixner [Sat, 6 Sep 2014 10:24:49 +0000 (12:24 +0200)]
timekeeping: Update timekeeper before updating vsyscall and pvclock
The update_walltime() code works on the shadow timekeeper to make the
seqcount protected region as short as possible. But that update to the
shadow timekeeper does not update all timekeeper fields because it's
sufficient to do that once before it becomes life. One of these fields
is tkr.base_mono. That stays stale in the shadow timekeeper unless an
operation happens which copies the real timekeeper to the shadow.
The update function is called after the update calls to vsyscall and
pvclock. While not correct, it did not cause any problems because none
of the invoked update functions used base_mono.
commit
cbcf2dd3b3d4 (x86: kvm: Make kvm_get_time_and_clockread()
nanoseconds based) changed that in the kvm pvclock update function, so
the stale mono_base value got used and caused kvm-clock to malfunction.
Put the update where it belongs and fix the issue.
Reported-by: Chris J Arges <chris.j.arges@canonical.com>
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1409050000570.3333@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sat, 6 Sep 2014 10:18:07 +0000 (12:18 +0200)]
compat: nanosleep: Clarify error handling
The error handling in compat_sys_nanosleep() is correct, but
completely non obvious. Document it and restrict it to the
-ERESTART_RESTARTBLOCK return value for clarity.
Reported-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
David S. Miller [Sat, 6 Sep 2014 05:37:36 +0000 (22:37 -0700)]
Merge branch 'amd-xgbe-net'
Tom Lendacky says:
====================
amd-xgbe: AMD XGBE driver fixes 2014-09-05
The following series of patches includes fixes to the driver.
- Proper access to 64 bit management counter registers
- Enable all management counter registers to generate an interrupt when
the counter threshold is reached
This patch series is based on net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 5 Sep 2014 23:02:36 +0000 (18:02 -0500)]
amd-xgbe: Enable interrupts for all management counters
As the management counters reach a threshold they will generate an
interrupt so the value can be saved and the counter reset. The
current code does not enable this interrupt on all counters. This
can result in inaccurate statistics.
Update the code to enable all the counters to generate an interrupt
when its threshold is exceeded.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 5 Sep 2014 23:02:30 +0000 (18:02 -0500)]
amd-xgbe: Treat certain counter registers as 64 bit
Even if the management counters are configured to be 32 bit register
values, the [rt]xoctetcount_gb and [rt]xoctetcount_g counters are
always 64 bit counter registers. Since they are not being treated as
64 bit values, these statistics are being reported incorrectly (ifconfig,
ethtool, etc.).
Update the routines used to read the registers to access the "hi"
register (an offset of 4 from the "lo" register) to create a 64 bit
value for these 64 bit counters.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Hellstrom [Fri, 5 Sep 2014 11:13:48 +0000 (13:13 +0200)]
greth: moved TX ring cleaning to NAPI rx poll func
This patch does not affect the 10/100 GRETH MAC.
Before all GBit GRETH TX descriptor ring cleaning was done in
start_xmit(), when descriptor list became full it activated
TX interrupt to start the NAPI rx poll function to do TX ring
cleaning.
With this patch the TX descriptor ring is always cleaned from
the NAPI rx poll function, triggered via TX or RX interrupt.
Otherwise we could end up in TX frames being sent but not
reported to the stack being sent. On the 10/100 GRETH this
is not an issue since the SKB is copied&aligned into private
buffers so that the SKB can be freed directly on start_xmit()
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anish Bhatt [Fri, 5 Sep 2014 00:12:57 +0000 (17:12 -0700)]
cnic : Cleanup CONFIG_IPV6 & VLAN check
The cnic module needs to ensure that if ipv6 support is compiled as a module,
then the cnic module cannot be compiled as built-in as it depends on ipv6.
Made this check cleaner via Kconfig
Use simpler IS_ENABLED for CONFIG_VLAN_8021Q check
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suman Tripathi [Thu, 28 Aug 2014 09:21:22 +0000 (14:51 +0530)]
ahci_xgene: Fix the link down in first attempt for the APM X-Gene SoC AHCI SATA host controller driver.
Due to HW errata the APM X-Gene AHCI SATA host controller reports link
down even if the device presence is detected. This issue is due to speed
negotiation failure. This patch implements the algorithm to retry the
COMRESET if PxSTAT register reports device presence detected but
PHY communication not established. The maximum retry attempts are 3.
This patch also fixes the code to match the algorithm for the printing
a warning message if the disparity error still exists after link up.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Suman Tripathi [Thu, 28 Aug 2014 09:21:21 +0000 (14:51 +0530)]
ahci_xgene: Skip the PHY and clock initialization if already configured by the firmware.
This patch implements the feature to skip the PHY and clock
initialization if it is already configured by the firmware.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Masanari Iida [Thu, 4 Sep 2014 14:44:36 +0000 (23:44 +0900)]
net: treewide: Fix typo found in DocBook/networking.xml
This patch fix spelling typo found in DocBook/networking.xml.
It is because the neworking.xml is generated from comments
in the source, I have to fix typo in comments within the source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Thu, 4 Sep 2014 10:26:00 +0000 (13:26 +0300)]
bnx2x: Fix link problems for 1G SFP RJ45 module
When 1G SFP RJ45 module is detected, driver must reset the Tx laser
in order to prevent link issues. As part of change, the link_attr_sync
was relocated from vars to params.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Thu, 4 Sep 2014 10:13:38 +0000 (06:13 -0400)]
3c59x: avoid panic in boomerang_start_xmit when finding page address:
This bug was reported on a very old kernel (RHEL6, 2.6.32-491.el6):
BUG: unable to handle kernel paging request at
00800000
IP: [<
c04107b5>] nommu_map_page+0x15/0x110
*pdpt =
000000003454f001 *pde =
000000003f03d067
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/system/cpu/online
Modules linked in: nfsd lockd nfs_acl auth_rpcgss sunrpc exportfs p4_clockmod
ipv6 ppdev parport_pc parport microcode iTCO_wdt iTCO_vendor_support 3c59x mii
dcdbas serio_raw snd_intel8x0 snd_ac97_codec ac97_bus snd_seq snd_seq_device
snd_pcm snd_timer snd soundcore snd_page_alloc i2c_i801 sg lpc_ich mfd_core ext4
jbd2 mbcache sr_mod cdrom sd_mod crc_t10dif pata_acpi ata_generic ata_piix
radeon ttm drm_kms_helper drm i2c_algo_bit i2c_core dm_mirror dm_region_hash
dm_log dm_mod [last unloaded: mperf]
Pid: 4219, comm: nfsd Not tainted 2.6.32-491.el6.i686 #1 Dell Computer
Corporation OptiPlex GX240 /OptiPlex GX240
EIP: 0060:[<
c04107b5>] EFLAGS:
00010246 CPU: 0
EIP is at nommu_map_page+0x15/0x110
EAX:
00000000 EBX:
c0a83480 ECX:
00000000 EDX:
00800000
ESI:
00000000 EDI:
f70e7860 EBP:
e2d09b54 ESP:
e2d09b24
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process nfsd (pid: 4219, ti=
e2d08000 task=
e2ceaaa0 task.ti=
e2d08000)
Stack:
00000056 00000000 0000000e c65efd38 00000020 00000296 00000206 00000206
<0>
c050c850 c0a83480 e2cef154 00000001 e2d09ba8 f8fcd585 00000510 00000001
<0>
00000000 00000000 f5172200 f8fdac00 0039ef8c f5277020 f70e7860 00000510
Call Trace:
[<
c050c850>] ? page_address+0xd0/0xe0
[<
f8fcd585>] ? boomerang_start_xmit+0x3b5/0x520 [3c59x]
[<
c07b2975>] ? dev_hard_start_xmit+0xe5/0x400
[<
f9182b00>] ? ip6_output_finish+0x0/0xf0 [ipv6]
[<
c07ca053>] ? sch_direct_xmit+0x113/0x180
[<
c07d5588>] ? nf_hook_slow+0x68/0x120
[<
c07b2ea5>] ? dev_queue_xmit+0x1b5/0x290
[<
f9182b6d>] ? ip6_output_finish+0x6d/0xf0 [ipv6]
[<
f9184cb8>] ? ip6_xmit+0x3e8/0x490 [ipv6]
[<
f91ab9f9>] ? inet6_csk_xmit+0x289/0x2f0 [ipv6]
[<
c07f6451>] ? tcp_transmit_skb+0x431/0x7f0
[<
c07a403f>] ? __alloc_skb+0x4f/0x140
[<
c07f85a2>] ? tcp_write_xmit+0x1c2/0xa50
[<
c07f90b1>] ? __tcp_push_pending_frames+0x31/0xe0
[<
c07ea47a>] ? tcp_sendpage+0x44a/0x4b0
[<
c07ea030>] ? tcp_sendpage+0x0/0x4b0
[<
c079be1e>] ? kernel_sendpage+0x4e/0x90
[<
f8457bb9>] ? svc_send_common+0xc9/0x120 [sunrpc]
[<
f8457c85>] ? svc_sendto+0x75/0x1f0 [sunrpc]
[<
c060d0d9>] ? _atomic_dec_and_lock+0x59/0x90
[<
f87d55d0>] ? nfs3svc_encode_readres+0x0/0xc0 [nfsd]
[<
f845876d>] ? svc_authorise+0x2d/0x40 [sunrpc]
[<
f87d4410>] ? nfs3svc_release_fhandle+0x0/0x10 [nfsd]
[<
f8455721>] ? svc_process_common+0xf1/0x5a0 [sunrpc]
[<
f8457e86>] ? svc_tcp_sendto+0x36/0xa0 [sunrpc]
[<
f8461778>] ? svc_send+0x98/0xd0 [sunrpc]
[<
f87c698c>] ? nfsd+0xac/0x140 [nfsd]
[<
c04470e0>] ? complete+0x40/0x60
[<
f87c68e0>] ? nfsd+0x0/0x140 [nfsd]
[<
c04802ac>] ? kthread+0x7c/0xa0
[<
c0480230>] ? kthread+0x0/0xa0
[<
c0409f9f>] ? kernel_thread_helper+0x7/0x10
Code: 8d b6 00 00 00 00 eb f8 8d b4 26 00 00 00 00 8d bc 27 00 00 00 00 55 89 e5
83 ec 30 89 75 f8 31 f6 89 7d fc 89 c7 89 c8 89 5d f4 <8b> 1a 8b 4d 08 c1 eb 19
c1 e3 04 8b 9b c0 29 c7 c0 83 e3 fc 29
But the problem seems to still exist upstream. It seems on 32 bit kernels
page_address() can reutrn a NULL value in some circumstances, and the
pci_map_single api isn't prepared to handle that (on this system it results in a
bogus pointer deference in nommu_map_page.
The fix is pretty easy, if we convert the 3c59x driver to use the more
convieient skb_frag_dma_map api we don't need to find the virtual address of the
page at all, and page gets mapped to the hardware properly. Verified to fix the
problem as described by the reporter.
Applies to the net tree
Change Notes:
v2) Converted PCI_DMA_TODEVICE to DMA_TO_DEVICE. Thanks Dave!
v3) Actually Run git commit after making changes to v2 :)
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: klassert@mathematik.tu-chemnitz.de
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>