igb: Workaround for igb i210 firmware issue

From: Chris J Arges <christopherarges@gmail.com>

[ Upstream commit 4e684f59d760a2c7c716bb60190783546e2d08a1 ]

Sometimes firmware may not properly initialize I347AT4_PAGE_SELECT causing
the probe of an igb i210 NIC to fail. This patch adds an addition zeroing
of this register during igb_get_phy_id to workaround this issue.

Thanks for Jochen Henneberg for the idea and original patch.

Signed-off-by: Chris J Arges <christopherarges@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen: do not re-use pirq number cached in pci device msi msg data

From: Dan Streetman <ddstreet@ieee.org>

[ Upstream commit c74fd80f2f41d05f350bb478151021f88551afe8 ]

Revert the main part of commit:
af42b8d12f8a ("xen: fix MSI setup and teardown for PV on HVM guests")

That commit introduced reading the pci device's msi message data to see
if a pirq was previously configured for the device's msi/msix, and re-use
that pirq.  At the time, that was the correct behavior.  However, a
later change to Qemu caused it to call into the Xen hypervisor to unmap
all pirqs for a pci device, when the pci device disables its MSI/MSIX
vectors; specifically the Qemu commit:
c976437c7dba9c7444fb41df45468968aaa326ad
("qemu-xen: free all the pirqs for msi/msix when driver unload")

Once Qemu added this pirq unmapping, it was no longer correct for the
kernel to re-use the pirq number cached in the pci device msi message
data.  All Qemu releases since 2.1.0 contain the patch that unmaps the
pirqs when the pci device disables its MSI/MSIX vectors.

This bug is causing failures to initialize multiple NVMe controllers
under Xen, because the NVMe driver sets up a single MSIX vector for
each controller (concurrently), and then after using that to talk to
the controller for some configuration data, it disables the single MSIX
vector and re-configures all the MSIX vectors it needs.  So the MSIX
setup code tries to re-use the cached pirq from the first vector
for each controller, but the hypervisor has already given away that
pirq to another controller, and its initialization fails.

This is discussed in more detail at:
https://lists.xen.org/archives/html/xen-devel/2017-01/msg00447.html

Fixes: af42b8d12f8a ("xen: fix MSI setup and teardown for PV on HVM guests")
Signed-off-by: Dan Streetman <dan.streetman@canonical.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfs: clear _XBF_PAGES from buffers when readahead page

commit 2aa6ba7b5ad3189cc27f14540aa2f57f0ed8df4b upstream.

If we try to allocate memory pages to back an xfs_buf that we're trying
to read, it's possible that we'll be so short on memory that the page
allocation fails.  For a blocking read we'll just wait, but for
readahead we simply dump all the pages we've collected so far.

Unfortunately, after dumping the pages we neglect to clear the
_XBF_PAGES state, which means that the subsequent call to xfs_buf_free
thinks that b_pages still points to pages we own.  It then double-frees
the b_pages pages.

This results in screaming about negative page refcounts from the memory
manager, which xfs oughtn't be triggering.  To reproduce this case,
mount a filesystem where the size of the inodes far outweighs the
availalble memory (a ~500M inode filesystem on a VM with 300MB memory
did the trick here) and run bulkstat in parallel with other memory
eating processes to put a huge load on the system.  The "check summary"
phase of xfs_scrub also works for this purpose.

Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Cc: Ivan Kozik <ivan@ludios.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usbtmc: add missing endpoint sanity check

commit 687e0687f71ec00e0132a21fef802dee88c2f1ad upstream.

USBTMC devices are required to have a bulk-in and a bulk-out endpoint,
but the driver failed to verify this, something which could lead to the
endpoint addresses being taken from uninitialised memory.

Make sure to zero all private data as part of allocation, and add the
missing endpoint sanity check.

Note that this also addresses a more recently introduced issue, where
the interrupt-in-presence flag would also be uninitialised whenever the
optional interrupt-in endpoint is not present. This in turn could lead
to an interrupt urb being allocated, initialised and submitted based on
uninitialised values.

Fixes: dbf3e7f654c0 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.")
Fixes: 5b775f672cc9 ("USB: add USB test and measurement class driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
[ johan: backport to v4.4 ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nl80211: fix dumpit error path RTNL deadlocks

commit ea90e0dc8cecba6359b481e24d9c37160f6f524f upstream.

Sowmini pointed out Dmitry's RTNL deadlock report to me, and it turns out
to be perfectly accurate - there are various error paths that miss unlock
of the RTNL.

To fix those, change the locking a bit to not be conditional in all those
nl80211_prepare_*_dump() functions, but make those require the RTNL to
start with, and fix the buggy error paths. This also let me use sparse
(by appropriately overriding the rtnl_lock/rtnl_unlock functions) to
validate the changes.

Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfs: fix up xfs_swap_extent_forks inline extent handling

commit 4dfce57db6354603641132fac3c887614e3ebe81 upstream.

There have been several reports over the years of NULL pointer
dereferences in xfs_trans_log_inode during xfs_fsr processes,
when the process is doing an fput and tearing down extents
on the temporary inode, something like:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
PID: 29439  TASK: ffff880550584fa0  CPU: 6   COMMAND: "xfs_fsr"
    [exception RIP: xfs_trans_log_inode+0x10]
 #9 [ffff8800a57bbbe0] xfs_bunmapi at ffffffffa037398e [xfs]
#10 [ffff8800a57bbce8] xfs_itruncate_extents at ffffffffa0391b29 [xfs]
#11 [ffff8800a57bbd88] xfs_inactive_truncate at ffffffffa0391d0c [xfs]
#12 [ffff8800a57bbdb8] xfs_inactive at ffffffffa0392508 [xfs]
#13 [ffff8800a57bbdd8] xfs_fs_evict_inode at ffffffffa035907e [xfs]
#14 [ffff8800a57bbe00] evict at ffffffff811e1b67
#15 [ffff8800a57bbe28] iput at ffffffff811e23a5
#16 [ffff8800a57bbe58] dentry_kill at ffffffff811dcfc8
#17 [ffff8800a57bbe88] dput at ffffffff811dd06c
#18 [ffff8800a57bbea8] __fput at ffffffff811c823b
#19 [ffff8800a57bbef0] ____fput at ffffffff811c846e
#20 [ffff8800a57bbf00] task_work_run at ffffffff81093b27
#21 [ffff8800a57bbf30] do_notify_resume at ffffffff81013b0c
#22 [ffff8800a57bbf50] int_signal at ffffffff8161405d

As it turns out, this is because the i_itemp pointer, along
with the d_ops pointer, has been overwritten with zeros
when we tear down the extents during truncate.  When the in-core
inode fork on the temporary inode used by xfs_fsr was originally
set up during the extent swap, we mistakenly looked at di_nextents
to determine whether all extents fit inline, but this misses extents
generated by speculative preallocation; we should be using if_bytes
instead.

This mistake corrupts the in-memory inode, and code in
xfs_iext_remove_inline eventually gets bad inputs, causing
it to memmove and memset incorrect ranges; this became apparent
because the two values in ifp->if_u2.if_inline_ext[1] contained
what should have been in d_ops and i_itemp; they were memmoved due
to incorrect array indexing and then the original locations
were zeroed with memset, again due to an array overrun.

Fix this by properly using i_df.if_bytes to determine the number
of extents, not di_nextents.

Thanks to dchinner for looking at this with me and spotting the
root cause.

[nborisov: backported to 4.4]

Cc: stable@vger.kernel.org
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
--
 fs/xfs/xfs_bmap_util.c |    7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

xfs: don't allow di_size with high bit set

commit ef388e2054feedaeb05399ed654bdb06f385d294 upstream.

The on-disk field di_size is used to set i_size, which is a signed
integer of loff_t.  If the high bit of di_size is set, we'll end up with
a negative i_size, which will cause all sorts of problems.  Since the
VFS won't let us create a file with such length, we should catch them
here in the verifier too.

Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Cc: Nikolay Borisov <n.borisov.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libceph: don't set weight to IN when OSD is destroyed

commit b581a5854eee4b7851dedb0f8c2ceb54fb902c06 upstream.

Since ceph.git commit 4e28f9e63644 ("osd/OSDMap: clear osd_info,
osd_xinfo on osd deletion"), weight is set to IN when OSD is deleted.
This changes the result of applying an incremental for clients, not
just OSDs.  Because CRUSH computations are obviously affected,
pre-4e28f9e63644 servers disagree with post-4e28f9e63644 clients on
object placement, resulting in misdirected requests.

Mirrors ceph.git commit a6009d1039a55e2c77f431662b3d6cc5a8e8e63f.

Fixes: 930c53286977 ("libceph: apply new_state before new_up_client on incrementals")
Link: http://tracker.ceph.com/issues/19122
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

raid10: increment write counter after bio is split

commit 9b622e2bbcf049c82e2550d35fb54ac205965f50 upstream.

md pending write counter must be incremented after bio is split,
otherwise it gets decremented too many times in end bio callback and
becomes negative.

Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Reviewed-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cpufreq: Restore policy min/max limits on CPU online

commit ff010472fb75670cb5c08671e820eeea3af59c87 upstream.

On CPU online the cpufreq core restores the previous governor (or
the previous "policy" setting for ->setpolicy drivers), but it does
not restore the min/max limits at the same time, which is confusing,
inconsistent and real pain for users who set the limits and then
suspend/resume the system (using full suspend), in which case the
limits are reset on all CPUs except for the boot one.

Fix this by making cpufreq_online() restore the limits when an inactive
policy is brought online.

The commit log and patch are inspired from Rafael's earlier work.

Reported-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: at91: sama5d2: add dma properties to UART nodes

commit b1708b72a0959a032cd2eebb77fa9086ea3e0c84 upstream.

The dmas/dma-names properties are added to the UART nodes. Note that additional
properties are needed to enable them at the board level: check bindings for
details.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: at91: pm: cpu_idle: switch DDR to power-down mode

commit 60b89f1928af80b546b5c3fd8714a62f6f4b8844 upstream.

On some DDR controllers, compatible with the sama5d3 one,
the sequence to enter/exit/re-enter the self-refresh mode adds
more constrains than what is currently written in the at91_idle
driver. An actual access to the DDR chip is needed between exit
and re-enter of this mode which is somehow difficult to implement.
This sequence can completely hang the SoC. It is particularly
experienced on parts which embed a L2 cache if the code run
between IDLE calls fits in it...

Moreover, as the intention is to enter and exit pretty rapidly
from IDLE, the power-down mode is a good candidate.

So now we use power-down instead of self-refresh. As we can
simplify the code for sama5d3 compatible DDR controllers,
we instantiate a new sama5d3_ddr_standby() function.

Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 017b5522d5e3 ("ARM: at91: Add new binding for sama5d3-ddramc")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/vt-d: Fix NULL pointer dereference in device_to_iommu

commit 5003ae1e735e6bfe4679d9bed6846274f322e77e upstream.

The function device_to_iommu() in the Intel VT-d driver
lacks a NULL-ptr check, resulting in this oops at boot on
some platforms:

 BUG: unable to handle kernel NULL pointer dereference at 00000000000007ab
 IP: [<ffffffff8132234a>] device_to_iommu+0x11a/0x1a0
 PGD 0

 [...]

 Call Trace:
   ? find_or_alloc_domain.constprop.29+0x1a/0x300
   ? dw_dma_probe+0x561/0x580 [dw_dmac_core]
   ? __get_valid_domain_for_dev+0x39/0x120
   ? __intel_map_single+0x138/0x180
   ? intel_alloc_coherent+0xb6/0x120
   ? sst_hsw_dsp_init+0x173/0x420 [snd_soc_sst_haswell_pcm]
   ? mutex_lock+0x9/0x30
   ? kernfs_add_one+0xdb/0x130
   ? devres_add+0x19/0x60
   ? hsw_pcm_dev_probe+0x46/0xd0 [snd_soc_sst_haswell_pcm]
   ? platform_drv_probe+0x30/0x90
   ? driver_probe_device+0x1ed/0x2b0
   ? __driver_attach+0x8f/0xa0
   ? driver_probe_device+0x2b0/0x2b0
   ? bus_for_each_dev+0x55/0x90
   ? bus_add_driver+0x110/0x210
   ? 0xffffffffa11ea000
   ? driver_register+0x52/0xc0
   ? 0xffffffffa11ea000
   ? do_one_initcall+0x32/0x130
   ? free_vmap_area_noflush+0x37/0x70
   ? kmem_cache_alloc+0x88/0xd0
   ? do_init_module+0x51/0x1c4
   ? load_module+0x1ee9/0x2430
   ? show_taint+0x20/0x20
   ? kernel_read_file+0xfd/0x190
   ? SyS_finit_module+0xa3/0xb0
   ? do_syscall_64+0x4a/0xb0
   ? entry_SYSCALL64_slow_path+0x25/0x25
 Code: 78 ff ff ff 4d 85 c0 74 ee 49 8b 5a 10 0f b6 9b e0 00 00 00 41 38 98 e0 00 00 00 77 da 0f b6 eb 49 39 a8 88 00 00 00 72 ce eb 8f <41> f6 82 ab 07 00 00 04 0f 85 76 ff ff ff 0f b6 4d 08 88 0e 49
 RIP  [<ffffffff8132234a>] device_to_iommu+0x11a/0x1a0
  RSP <ffffc90001457a78>
 CR2: 00000000000007ab
 ---[ end trace 16f974b6d58d0aad ]---

Add the missing pointer check.

Fixes: 1c387188c60f53b338c20eee32db055dfe022a9b ("iommu/vt-d: Fix IOMMU lookup for SR-IOV Virtual Functions")
Signed-off-by: Koos Vriezen <koos.vriezen@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/acpi: upload PM state from init-domain to Xen

commit 1914f0cd203c941bba72f9452c8290324f1ef3dc upstream.

This was broken in commit cd979883b9ed ("xen/acpi-processor:
fix enabling interrupts on syscore_resume"). do_suspend (from
xen/manage.c) and thus xen_resume_notifier never get called on
the initial-domain at resume (it is if running as guest.)

The rationale for the breaking change was that upload_pm_data()
potentially does blocking work in syscore_resume(). This patch
addresses the original issue by scheduling upload_pm_data() to
execute in workqueue context.

Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Based-on-patch-by: Konrad Wilk <konrad.wilk@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: sdhci: Do not disable interrupts while waiting for clock

commit e2ebfb2142acefecc2496e71360f50d25726040b upstream.

Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when sdhci changes clock frequency because it
waits for the clock to become stable under a spin lock.

The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.

Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: mark inode dirty after converting inline directory

commit b9cf625d6ecde0d372e23ae022feead72b4228a6 upstream.

If ext4_convert_inline_data() was called on a directory with inline
data, the filesystem was left in an inconsistent state (as considered by
e2fsck) because the file size was not increased to cover the new block.
This happened because the inode was not marked dirty after i_disksize
was updated.  Fix this by marking the inode dirty at the end of
ext4_finish_convert_inline_dir().

This bug was probably not noticed before because most users mark the
inode dirty afterwards for other reasons.  But if userspace executed
FS_IOC_SET_ENCRYPTION_POLICY with invalid parameters, as exercised by
'kvm-xfstests -c adv generic/396', then the inode was never marked dirty
after updating i_disksize.

Fixes: 3c47d54170b6a678875566b1b8d6dcf57904e49b
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parport: fix attempt to write duplicate procfiles

commit 03270c6ac6207fc55bbf9d20d195029dca210c79 upstream.

Usually every parallel port will have a single pardev registered with
it. But ppdev driver is an exception. This userspace parallel port
driver allows to create multiple parrallel port devices for a single
parallel port. And as a result we were having a nice warning like:
"sysctl table check failed:
/dev/parport/parport0/devices/ppdev0/timeslice Sysctl already exists"

Use the same logic as used in parport_register_device() and register
the proc files only once for each parallel port.

Fixes: 6fa45a226897 ("parport: add device-model to parport subsystem")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1414656
Bugzilla: https://bugs.archlinux.org/task/52322
Tested-by: James Feeney <james@nurealm.net>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3

commit 3bec247474469f769af41e8c80d3a100dd97dd76 upstream.

In function _hid_sensor_power_state(), when hid_sensor_read_poll_value()
is called, sensor's all properties will be updated by the value from
sensor hardware/firmware.
In some implementation, sensor hardware/firmware will do a power cycle
during S3. In this case, after resume, once hid_sensor_read_poll_value()
is called, sensor's all properties which are kept by driver during S3
will be changed to default value.
But instead, if a set feature function is called first, sensor
hardware/firmware will be recovered to the last status. So change the
sensor_hub_set_feature() calling order to behind of set feature function
to avoid sensor properties lose.

Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: ti_am335x_adc: fix fifo overrun recovery

commit e83bb3e6f3efa21f4a9d883a25d0ecd9dfb431e1 upstream.

The tiadc_irq_h(int irq, void *private) function is handling FIFO
overruns by clearing flags, disabling and enabling the ADC to
recover.

If the ADC is running in continuous mode a FIFO overrun happens
regularly. If the disabling of the ADC happens concurrently with
a new conversion. It might happen that the enabling of the ADC
is ignored by the hardware. This stops the ADC permanently. No
more interrupts are triggered.

According to the AM335x Reference Manual (SPRUH73H October 2011 -
Revised April 2013 - Chapter 12.4 and 12.5) it is necessary to
check the ADC FSM bits in REG_ADCFSM before enabling the ADC
again. Because the disabling of the ADC is done right after the
current conversion has been finished.

To trigger this bug it is necessary to run the ADC in continuous
mode. The ADC values of all channels need to be read in an endless
loop. The bug appears within the first 6 hours (~5.4 million
handled FIFO overruns). The user space application will hang on
reading new values from the character device.

Fixes: ca9a563805f7a ("iio: ti_am335x_adc: Add continuous sampling support")
Signed-off-by: Michael Engl <michael.engl@wjw-solutions.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: ushc: fix NULL-deref at probe

commit 181302dc7239add8ab1449c23ecab193f52ee6ab upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Fixes: 53f3a9e26ed5 ("mmc: USB SD Host Controller (USHC) driver")
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

uwb: hwa-rc: fix NULL-deref at probe

commit daf229b15907fbfdb6ee183aac8ca428cb57e361 upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Note that the dereference happens in the start callback which is called
during probe.

Fixes: de520b8bd552 ("uwb: add HWA radio controller driver")
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

uwb: i1480-dfu: fix NULL-deref at probe

commit 4ce362711d78a4999011add3115b8f4b0bc25e8c upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Note that the dereference happens in the cmd and wait_init_done
callbacks which are called during probe.

Fixes: 1ba47da52712 ("uwb: add the i1480 DFU driver")
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: hub: Fix crash after failure to read BOS descriptor

commit 7b2db29fbb4e766fcd02207eb2e2087170bd6ebc upstream.

If usb_get_bos_descriptor() returns an error, usb->bos will be NULL.
Nevertheless, it is dereferenced unconditionally in
hub_set_initial_usb2_lpm_policy() if usb2_hw_lpm_capable is set.
This results in a crash.

usb 5-1: unable to get BOS descriptor
...
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = ffffffc00165f000
[00000008] *pgd=000000000174f003, *pud=000000000174f003,
*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac [ ... ]
CPU: 5 PID: 3353 Comm: kworker/5:3 Tainted: G    B 4.4.52 #480
Hardware name: Google Kevin (DT)
Workqueue: events driver_set_config_work
task: ffffffc0c3690000 ti: ffffffc0ae9a8000 task.ti: ffffffc0ae9a8000
PC is at hub_port_init+0xc3c/0xd10
LR is at hub_port_init+0xc3c/0xd10
...
Call trace:
[<ffffffc0007fbbfc>] hub_port_init+0xc3c/0xd10
[<ffffffc0007fbe2c>] usb_reset_and_verify_device+0x15c/0x82c
[<ffffffc0007fc5e0>] usb_reset_device+0xe4/0x298
[<ffffffbffc0e3fcc>] rtl8152_probe+0x84/0x9b0 [r8152]
[<ffffffc00080ca8c>] usb_probe_interface+0x244/0x2f8
[<ffffffc000774a24>] driver_probe_device+0x180/0x3b4
[<ffffffc000774e48>] __device_attach_driver+0xb4/0xe0
[<ffffffc000772168>] bus_for_each_drv+0xb4/0xe4
[<ffffffc0007747ec>] __device_attach+0xd0/0x158
[<ffffffc000775080>] device_initial_probe+0x24/0x30
[<ffffffc0007739d4>] bus_probe_device+0x50/0xe4
[<ffffffc000770bd0>] device_add+0x414/0x738
[<ffffffc000809fe8>] usb_set_configuration+0x89c/0x914
[<ffffffc00080a120>] driver_set_config_work+0xc0/0xf0
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40

Since we don't know anything about LPM capabilities without BOS descriptor,
don't attempt to enable LPM if it is not available.

Fixes: 890dae886721 ("xhci: Enable LPM support only for hardwired ...")
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: cppi41: don't check early-TX-interrupt for Isoch transfer

commit 0090114d336a9604aa2d90bc83f20f7cd121b76c upstream.

The CPPI 4.1 driver polls register to workaround the premature TX
interrupt issue, but it causes audio playback underrun when triggered in
Isoch transfers.

Isoch doesn't do back-to-back transfers, the TX should be done by the
time the next transfer is scheduled. So skip this polling workaround for
Isoch transfer.

Fixes: a655f481d83d6 ("usb: musb: musb_cppi41: handle pre-mature TX complete interrupt")
Reported-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: wusbcore: fix NULL-deref at probe

commit 03ace948a4eb89d1cf51c06afdfc41ebca5fdb27 upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.

This specifically fixes the NULL-pointer dereference when probing HWA HC
devices.

Fixes: df3654236e31 ("wusb: add the Wire Adapter (WA) core")
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: idmouse: fix NULL-deref at probe

commit b0addd3fa6bcd119be9428996d5d4522479ab240 upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: lvtest: fix NULL-deref at probe

commit 1dc56c52d2484be09c7398a5207d6b11a4256be9 upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should the probed device lack endpoints.

Note that this driver does not bind to any devices by default.

Fixes: ce21bfe603b3 ("USB: Add LVS Test device driver")
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: uss720: fix NULL-deref at probe

commit f259ca3eed6e4b79ac3d5c5c9fb259fb46e86217 upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.

Note that the endpoint access that causes the NULL-deref is currently
only used for debugging purposes during probe so the oops only happens
when dynamic debugging is enabled. This means the driver could be
rewritten to continue to accept device with only two endpoints, should
such devices exist.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb-core: Add LINEAR_FRAME_INTR_BINTERVAL USB quirk

commit 3243367b209faed5c320a4e5f9a565ee2a2ba958 upstream.

Some USB 2.0 devices erroneously report millisecond values in
bInterval. The generic config code manages to catch most of them,
but in some cases it's not completely enough.

The case at stake here is a USB 2.0 braille device, which wants to
announce 10ms and thus sets bInterval to 10, but with the USB 2.0
computation that yields to 64ms.  It happens that one can type fast
enough to reach this interval and get the device buffers overflown,
leading to problematic latencies.  The generic config code does not
catch this case because the 64ms is considered a sane enough value.

This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk
to mark devices which actually report milliseconds in bInterval,
and marks Vario Ultra devices as needing it.

Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: f_uvc: Fix SuperSpeed companion descriptor's wBytesPerInterval

commit 09424c50b7dff40cb30011c09114404a4656e023 upstream.

The streaming_maxburst module parameter is 0 offset (0..15)
so we must add 1 while using it for wBytesPerInterval
calculation for the SuperSpeed companion descriptor.

Without this host uvcvideo driver will always see the wrong
wBytesPerInterval for SuperSpeed uvc gadget and may not find
a suitable video interface endpoint.
e.g. for streaming_maxburst = 0 case it will always
fail as wBytePerInterval was evaluating to 0.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACM gadget: fix endianness in notifications

commit cdd7928df0d2efaa3270d711963773a08a4cc8ab upstream.

The gadget code exports the bitfield for serial status changes
over the wire in its internal endianness. The fix is to convert
to little endian before sending it over the wire.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: 家瑋 <momo1208@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: qcserial: add Dell DW5811e

commit 436ecf5519d892397af133a79ccd38a17c25fa51 upstream.

This is a Dell branded Sierra Wireless EM7455.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: add Quectel UC15, UC20, EC21, and EC25 modems

commit 6e9f44eaaef0df7b846e9316fa9ca72a02025d44 upstream.

Add Quectel UC15, UC20, EC21, and EC25.  The EC20 is handled by
qcserial due to a USB VID/PID conflict with an existing Acer
device.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda - Adding a group of pin definition to fix headset problem

commit 3f307834e695f59dac4337a40316bdecfb9d0508 upstream.

A new Dell laptop needs to apply ALC269_FIXUP_DELL1_MIC_NO_PRESENCE to
fix the headset problem, and the pin definiton of this machine is not
in the pin quirk table yet, now adding it to the table.

Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: ctxfi: Fix the incorrect check of dma_set_mask() call

commit f363a06642f28caaa78cb6446bbad90c73fe183c upstream.

In the commit [15c75b09f8d1: ALSA: ctxfi: Fallback DMA mask to 32bit],
I forgot to put "!" at dam_set_mask() call check in cthw20k1.c (while
cthw20k2.c is OK).  This patch fixes that obvious bug.

(As a side note: although the original commit was completely wrong,
 it's still working for most of machines, as it sets to 32bit DMA mask
 in the end.  So the bug severity is low.)

Fixes: 15c75b09f8d1 ("ALSA: ctxfi: Fallback DMA mask to 32bit")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: seq: Fix racy cell insertions during snd_seq_pool_done()

commit c520ff3d03f0b5db7146d9beed6373ad5d2a5e0e upstream.

When snd_seq_pool_done() is called, it marks the closing flag to
refuse the further cell insertions.  But snd_seq_pool_done() itself
doesn't clear the cells but just waits until all cells are cleared by
the caller side.  That is, it's racy, and this leads to the endless
stall as syzkaller spotted.

This patch addresses the racy by splitting the setup of pool->closing
flag out of snd_seq_pool_done(), and calling it properly before
snd_seq_pool_done().

BugLink: http://lkml.kernel.org/r/CACT4Y+aqqy8bZA1fFieifNxR2fAfFQQABcBHj801+u5ePV0URw@mail.gmail.com
Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: sur40 - validate number of endpoints before using them

commit 92461f5d723037530c1f36cce93640770037812c upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.

Fixes: bdb5c57f209c ("Input: add sur40 driver for Samsung SUR40... ")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: kbtab - validate number of endpoints before using them

commit cb1b494663e037253337623bf1ef2df727883cb7 upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: cm109 - validate number of endpoints before using them

commit ac2ee9ba953afe88f7a673e1c0c839227b1d7891 upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Fixes: c04148f915e5 ("Input: add driver for USB VoIP phones with CM109...")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: yealink - validate number of endpoints before using them

commit 5cc4a1a9f5c179795c8a1f2b0f4361829d6a070e upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Fixes: aca951a22a1d ("[PATCH] input-driver-yealink-P1K-usb-phone")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: hanwang - validate number of endpoints before using them

commit ba340d7b83703768ce566f53f857543359aa1b98 upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Fixes: bba5394ad3bd ("Input: add support for Hanwang tablets")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: ims-pcu - validate number of endpoints before using them

commit 1916d319271664241b7aa0cd2b05e32bdb310ce9 upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack control-interface endpoints.

Fixes: 628329d52474 ("Input: add IMS Passenger Control Unit driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: iforce - validate number of endpoints before using them

commit 59cf8bed44a79ec42303151dd014fdb6434254bb upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.

Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: i8042 - add noloop quirk for Dell Embedded Box PC 3000

commit 45838660e34d90db8d4f7cbc8fd66e8aff79f4fe upstream.

The aux port does not get detected without noloop quirk, so external PS/2
mouse cannot work as result.

The PS/2 mouse can work with this quirk.

BugLink: https://bugs.launchpad.net/bugs/1591053
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: elan_i2c - add ASUS EeeBook X205TA special touchpad fw

commit 92ef6f97a66e580189a41a132d0f8a9f78d6ddce upstream.

EeeBook X205TA is yet another ASUS device with a special touchpad
firmware that needs to be accounted for during initialization, or
else the touchpad will go into an invalid state upon suspend/resume.
Adding the appropriate ic_type and product_id check fixes the problem.

Signed-off-by: Matjaz Hegedic <matjaz.hegedic@gmail.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: initialize icsk_ack.lrcvtime at session start time

[ Upstream commit 15bb7745e94a665caf42bfaabf0ce062845b533b ]

icsk_ack.lrcvtime has a 0 value at socket creation time.

tcpi_last_data_recv can have bogus value if no payload is ever received.

This patch initializes icsk_ack.lrcvtime for active sessions
in tcp_finish_connect(), and for passive sessions in
tcp_create_openreq_child()

Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

socket, bpf: fix sk_filter use after free in sk_clone_lock

[ Upstream commit a97e50cc4cb67e1e7bff56f6b41cda62ca832336 ]

In sk_clone_lock(), we create a new socket and inherit most of the
parent's members via sock_copy() which memcpy()'s various sections.
Now, in case the parent socket had a BPF socket filter attached,
then newsk->sk_filter points to the same instance as the original
sk->sk_filter.

sk_filter_charge() is then called on the newsk->sk_filter to take a
reference and should that fail due to hitting max optmem, we bail
out and release the newsk instance.

The issue is that commit 278571baca2a ("net: filter: simplify socket
charging") wrongly combined the dismantle path with the failure path
of xfrm_sk_clone_policy(). This means, even when charging failed, we
call sk_free_unlock_clone() on the newsk, which then still points to
the same sk_filter as the original sk.

Thus, sk_free_unlock_clone() calls into __sk_destruct() eventually
where it tests for present sk_filter and calls sk_filter_uncharge()
on it, which potentially lets sk_omem_alloc wrap around and releases
the eBPF prog and sk_filter structure from the (still intact) parent.

Fix it by making sure that when sk_filter_charge() failed, we reset
newsk->sk_filter back to NULL before passing to sk_free_unlock_clone(),
so that we don't mess with the parents sk_filter.

Only if xfrm_sk_clone_policy() fails, we did reach the point where
either the parent's filter was NULL and as a result newsk's as well
or where we previously had a successful sk_filter_charge(), thus for
that case, we do need sk_filter_uncharge() to release the prior taken
reference on sk_filter.

Fixes: 278571baca2a ("net: filter: simplify socket charging")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv4: provide stronger user input validation in nl_fib_input()

[ Upstream commit c64c0b3cac4c5b8cb093727d2c19743ea3965c0b ]

Alexander reported a KMSAN splat caused by reads of uninitialized
field (tb_id_in) from user provided struct fib_result_nl

It turns out nl_fib_input() sanity tests on user input is a bit
wrong :

User can pretend nlh->nlmsg_len is big enough, but provide
at sendmsg() time a too small buffer.

Reported-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: bcmgenet: remove bcmgenet_internal_phy_setup()

[ Upstream commit 31739eae738ccbe8b9d627c3f2251017ca03f4d2 ]

Commit 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset")
removed the bcmgenet_mii_reset() function from bcmgenet_power_up() and
bcmgenet_internal_phy_setup() functions.  In so doing it broke the reset
of the internal PHY devices used by the GENETv1-GENETv3 which required
this reset before the UniMAC was enabled.  It also broke the internal
GPHY devices used by the GENETv4 because the config_init that installed
the AFE workaround was no longer occurring after the reset of the GPHY
performed by bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup().
In addition the code in bcmgenet_internal_phy_setup() related to the
"enable APD" comment goes with the bcmgenet_mii_reset() so it should
have also been removed.

Commit bd4060a6108b ("net: bcmgenet: Power on integrated GPHY in
bcmgenet_power_up()") moved the bcmgenet_phy_power_set() call to the
bcmgenet_power_up() function, but failed to remove it from the
bcmgenet_internal_phy_setup() function.  Had it done so, the
bcmgenet_internal_phy_setup() function would have been empty and could
have been removed at that time.

Commit 5dbebbb44a6a ("net: bcmgenet: Software reset EPHY after power on")
was submitted to correct the functional problems introduced by
commit 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset"). It
was included in v4.4 and made available on 4.3-stable. Unfortunately,
it didn't fully revert the commit because this bcmgenet_mii_reset()
doesn't apply the soft reset to the internal GPHY used by GENETv4 like
the previous one did. This prevents the restoration of the AFE work-
arounds for internal GPHY devices after the bcmgenet_phy_power_set() in
bcmgenet_internal_phy_setup().

This commit takes the alternate approach of removing the unnecessary
bcmgenet_internal_phy_setup() function which shouldn't have been in v4.3
so that when bcmgenet_mii_reset() was restored it should have only gone
into bcmgenet_power_up().  This will avoid the problems while also
removing the redundancy (and hopefully some of the confusion).

Fixes: 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5e: Count LRO packets correctly

[ Upstream commit 8ab7e2ae15d84ba758b2c8c6f4075722e9bd2a08 ]

RX packets statistics ('rx_packets' counter) used to count LRO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.

Note that no information is lost in this patch due to 'rx_lro_packets'
counter existence.

Before, ethtool showed:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
     rx_packets: 435277
     rx_lro_packets: 35847
     rx_packets_phy: 1935066

Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
     rx_packets: 1935066
     rx_lro_packets: 35847
     rx_packets_phy: 1935066

Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: Increase number of max QPs in default profile

[ Upstream commit 5f40b4ed975c26016cf41953b7510fe90718e21c ]

With ConnectX-4 sharing SRQs from the same space as QPs, we hit a
limit preventing some applications to allocate needed QPs amount.
Double the size to 256K.

Fixes: e126ba97dba9e ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: unix: properly re-increment inflight counter of GC discarded candidates

[ Upstream commit 7df9c24625b9981779afb8fcdbe2bb4765e61147 ]

Dmitry has reported that a BUG_ON() condition in unix_notinflight()
may be triggered by a simple code that forwards unix socket in an
SCM_RIGHTS message.
That is caused by incorrect unix socket GC implementation in unix_gc().

The GC first collects list of candidates, then (a) decrements their
"children's" inflight counter, (b) checks which inflight counters are
now 0, and then (c) increments all inflight counters back.
(a) and (c) are done by calling scan_children() with inc_inflight or
dec_inflight as the second argument.

Commit 6209344f5a37 ("net: unix: fix inflight counting bug in garbage
collector") changed scan_children() such that it no longer considers
sockets that do not have UNIX_GC_CANDIDATE flag. It also added a block
of code that that unsets this flag _before_ invoking
scan_children(, dec_iflight, ). This may lead to incorrect inflight
counters for some sockets.

This change fixes this bug by changing order of operations:
UNIX_GC_CANDIDATE is now unset only after all inflight counters are
restored to the original state.

  kernel BUG at net/unix/garbage.c:149!
  RIP: 0010:[<ffffffff8717ebf4>]  [<ffffffff8717ebf4>]
  unix_notinflight+0x3b4/0x490 net/unix/garbage.c:149
  Call Trace:
   [<ffffffff8716cfbf>] unix_detach_fds.isra.19+0xff/0x170 net/unix/af_unix.c:1487
   [<ffffffff8716f6a9>] unix_destruct_scm+0xf9/0x210 net/unix/af_unix.c:1496
   [<ffffffff86a90a01>] skb_release_head_state+0x101/0x200 net/core/skbuff.c:655
   [<ffffffff86a9808a>] skb_release_all+0x1a/0x60 net/core/skbuff.c:668
   [<ffffffff86a980ea>] __kfree_skb+0x1a/0x30 net/core/skbuff.c:684
   [<ffffffff86a98284>] kfree_skb+0x184/0x570 net/core/skbuff.c:705
   [<ffffffff871789d5>] unix_release_sock+0x5b5/0xbd0 net/unix/af_unix.c:559
   [<ffffffff87179039>] unix_release+0x49/0x90 net/unix/af_unix.c:836
   [<ffffffff86a694b2>] sock_release+0x92/0x1f0 net/socket.c:570
   [<ffffffff86a6962b>] sock_close+0x1b/0x20 net/socket.c:1017
   [<ffffffff81a76b8e>] __fput+0x34e/0x910 fs/file_table.c:208
   [<ffffffff81a771da>] ____fput+0x1a/0x20 fs/file_table.c:244
   [<ffffffff81483ab0>] task_work_run+0x1a0/0x280 kernel/task_work.c:116
   [<     inline     >] exit_task_work include/linux/task_work.h:21
   [<ffffffff8141287a>] do_exit+0x183a/0x2640 kernel/exit.c:828
   [<ffffffff8141383e>] do_group_exit+0x14e/0x420 kernel/exit.c:931
   [<ffffffff814429d3>] get_signal+0x663/0x1880 kernel/signal.c:2307
   [<ffffffff81239b45>] do_signal+0xc5/0x2190 arch/x86/kernel/signal.c:807
   [<ffffffff8100666a>] exit_to_usermode_loop+0x1ea/0x2d0
  arch/x86/entry/common.c:156
   [<     inline     >] prepare_exit_to_usermode arch/x86/entry/common.c:190
   [<ffffffff81009693>] syscall_return_slowpath+0x4d3/0x570
  arch/x86/entry/common.c:259
   [<ffffffff881478e6>] entry_SYSCALL_64_fastpath+0xc4/0xc6

Link: https://lkml.org/lkml/2017/3/6/252
Signed-off-by: Andrey Ulanov <andreyu@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Fixes: 6209344 ("net: unix: fix inflight counting bug in garbage collector")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

amd-xgbe: Fix jumbo MTU processing on newer hardware

[ Upstream commit 622c36f143fc9566ba49d7cec994c2da1182d9e2 ]

Newer hardware does not provide a cumulative payload length when multiple
descriptors are needed to handle the data. Once the MTU increases beyond
the size that can be handled by a single descriptor, the SKB does not get
built properly by the driver.

The driver will now calculate the size of the data buffers used by the
hardware.  The first buffer of the first descriptor is for packet headers
or packet headers and data when the headers can't be split. Subsequent
descriptors in a multi-descriptor chain will not use the first buffer. The
second buffer is used by all the descriptors in the chain for payload data.
Based on whether the driver is processing the first, intermediate, or last
descriptor it can calculate the buffer usage and build the SKB properly.

Tested and verified on both old and new hardware.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: properly release sk_frag.page

[ Upstream commit 22a0e18eac7a9e986fec76c60fa4a2926d1291e2 ]

I mistakenly added the code to release sk->sk_frag in
sk_common_release() instead of sk_destruct()

TCP sockets using sk->sk_allocation == GFP_ATOMIC do no call
sk_common_release() at close time, thus leaking one (order-3) page.

iSCSI is using such sockets.

Fixes: 5640f7685831 ("net: use a per task frag allocator")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: bcmgenet: Do not suspend PHY if Wake-on-LAN is enabled

[ Upstream commit 5371bbf4b295eea334ed453efa286afa2c3ccff3 ]

Suspending the PHY would be putting it in a low power state where it
may no longer allow us to do Wake-on-LAN.

Fixes: cc013fb48898 ("net: bcmgenet: correctly suspend and resume PHY device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/openvswitch: Set the ipv6 source tunnel key address attribute correctly

[ Upstream commit 3d20f1f7bd575d147ffa75621fa560eea0aec690 ]

When dealing with ipv6 source tunnel key address attribute
(OVS_TUNNEL_KEY_ATTR_IPV6_SRC) we are wrongly setting the tunnel
dst ip, fix that.

Fixes: 6b26ba3a7d95 ('openvswitch: netlink attributes for IPv6 tunneling')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.4.57

ext4: fix fencepost in s_first_meta_bg validation

commit 2ba3e6e8afc9b6188b471f27cf2b5e3cf34e7af2 upstream.

It is OK for s_first_meta_bg to be equal to the number of block group
descriptor blocks.  (It rarely happens, but it shouldn't cause any
problems.)

https://bugzilla.kernel.org/show_bug.cgi?id=194567

Fixes: 3a4b77cd47bb837b8557595ec7425f281f2ca1fe
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

percpu: acquire pcpu_lock when updating pcpu_nr_empty_pop_pages

commit 320661b08dd6f1746d5c7ab4eb435ec64b97cd45 upstream.

Update to pcpu_nr_empty_pop_pages in pcpu_alloc() is currently done
without holding pcpu_lock. This can lead to bad updates to the variable.
Add missing lock calls.

Fixes: b539b87fed37 ("percpu: implmeent pcpu_nr_empty_pop_pages and chunk->nr_populated")
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gfs2: Avoid alignment hole in struct lm_lockname

commit 28ea06c46fbcab63fd9a55531387b7928a18a590 upstream.

Commit 88ffbf3e03 switches to using rhashtables for glocks, hashing over
the entire struct lm_lockname instead of its individual fields.  On some
architectures, struct lm_lockname contains a hole of uninitialized
memory due to alignment rules, which now leads to incorrect hash values.
Get rid of that hole.

Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

isdn/gigaset: fix NULL-deref at probe

commit 68c32f9c2a36d410aa242e661506e5b2c2764179 upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Fixes: cf7776dc05b8 ("[PATCH] isdn4linux: Siemens Gigaset drivers - direct USB connection")
Cc: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

target: Fix VERIFY_16 handling in sbc_parse_cdb

commit 13603685c1f12c67a7a2427f00b63f39a2b6f7c9 upstream.

As reported by Max, the Windows 2008 R2 chkdsk utility expects
VERIFY_16 to be supported, and does not handle the returned
CHECK_CONDITION properly, resulting in an infinite loop.

The kernel will log huge amounts of this error:

kernel: TARGET_CORE[iSCSI]: Unsupported SCSI Opcode 0x8f, sending
CHECK_CONDITION.

Signed-off-by: Max Lohrmann <post@wickenrode.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: libiscsi: add lock around task lists to fix list corruption regression

commit 6f8830f5bbab16e54f261de187f3df4644a5b977 upstream.

There's a rather long standing regression from the commit "libiscsi:
Reduce locking contention in fast path"

Depending on iSCSI target behavior, it's possible to hit the case in
iscsi_complete_task where the task is still on a pending list
(!list_empty(&task->running)).  When that happens the task is removed
from the list while holding the session back_lock, but other task list
modification occur under the frwd_lock.  That leads to linked list
corruption and eventually a panicked system.

Rather than back out the session lock split entirely, in order to try
and keep some of the performance gains this patch adds another lock to
maintain the task lists integrity.

Major enterprise supported kernels have been backing out the lock split
for while now, thanks to the efforts at IBM where a lab setup has the
most reliable reproducer I've seen on this issue.  This patch has been
tested there successfully.

Signed-off-by: Chris Leech <cleech@redhat.com>
Fixes: 659743b02c41 ("[SCSI] libiscsi: Reduce locking contention in fast path")
Reported-by: Prashantha Subbarao <psubbara@us.ibm.com>
Reviewed-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: lpfc: Add shutdown method for kexec

commit 85e8a23936ab3442de0c42da97d53b29f004ece1 upstream.

We see lpfc devices regularly fail during kexec. Fix this by adding a
shutdown method which mirrors the remove method.

Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Tested-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

target/pscsi: Fix TYPE_TAPE + TYPE_MEDIMUM_CHANGER export

commit a04e54f2c35823ca32d56afcd5cea5b783e2f51a upstream.

The following fixes a divide by zero OOPs with TYPE_TAPE
due to pscsi_tape_read_blocksize() failing causing a zero
sd->sector_size being propigated up via dev_attrib.hw_block_size.

It also fixes another long-standing bug where TYPE_TAPE and
TYPE_MEDIMUM_CHANGER where using pscsi_create_type_other(),
which does not call scsi_device_get() to take the device
reference.  Instead, rename pscsi_create_type_rom() to
pscsi_create_type_nondisk() and use it for all cases.

Finally, also drop a dump_stack() in pscsi_get_blocks() for
non TYPE_DISK, which in modern target-core can get invoked
via target_sense_desc_format() during CHECK_CONDITION.

Reported-by: Malcolm Haak <insanemal@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md/raid1/10: fix potential deadlock

commit 61eb2b43b99ebdc9bc6bc83d9792257b243e7cb3 upstream.

Neil Brown pointed out a potential deadlock in raid 10 code with
bio_split/chain. The raid1 code could have the same issue, but recent
barrier rework makes it less likely to happen. The deadlock happens in
below sequence:

1. generic_make_request(bio), this will set current->bio_list
2. raid10_make_request will split bio to bio1 and bio2
3. __make_request(bio1), wait_barrer, add underlayer disk bio to
current->bio_list
4. __make_request(bio2), wait_barrer

If raise_barrier happens between 3 & 4, since wait_barrier runs at 3,
raise_barrier waits for IO completion from 3. And since raise_barrier
sets barrier, 4 waits for raise_barrier. But IO from 3 can't be
dispatched because raid10_make_request() doesn't finished yet.

The solution is to adjust the IO ordering. Quotes from Neil:
"
It is much safer to:

    if (need to split) {
        split = bio_split(bio, ...)
        bio_chain(...)
        make_request_fn(split);
        generic_make_request(bio);
   } else
        make_request_fn(mddev, bio);

This way we first process the initial section of the bio (in 'split')
which will queue some requests to the underlying devices.  These
requests will be queued in generic_make_request.
Then we queue the remainder of the bio, which will be added to the end
of the generic_make_request queue.
Then we return.
generic_make_request() will pop the lower-level device requests off the
queue and handle them first.  Then it will process the remainder
of the original bio once the first section has been fully processed.
"

Note, this only happens in read path. In write path, the bio is flushed to
underlaying disks either by blk flush (from schedule) or offladed to raid1/10d.
It's queued in current->bio_list.

Cc: Coly Li <colyli@suse.de>
Suggested-by: NeilBrown <neilb@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/boot: Fix zImage TOC alignment

commit 97ee351b50a49717543533cfb85b4bf9d88c9680 upstream.

Recent toolchains force the TOC to be 256 byte aligned. We need to
enforce this alignment in the zImage linker script, otherwise pointers
to our TOC variables (__toc_start) could be incorrect. If the actual
start of the TOC and __toc_start don't have the same value we crash
early in the zImage wrapper.

Suggested-by: Alan Modra <amodra@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cpufreq: Fix and clean up show_cpuinfo_cur_freq()

commit 9b4f603e7a9f4282aec451063ffbbb8bb410dcd9 upstream.

There is a missing newline in show_cpuinfo_cur_freq(), so add it,
but while at it clean that function up somewhat too.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf/core: Fix event inheritance on fork()

commit e7cc4865f0f31698ef2f7aac01a50e78968985b7 upstream.

While hunting for clues to a use-after-free, Oleg spotted that
perf_event_init_context() can loose an error value with the result
that fork() can succeed even though we did not fully inherit the perf
event context.

Spotted-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: oleg@redhat.com
Fixes: 889ff0150661 ("perf/core: Split context's event group list into pinned and non-pinned lists")
Link: http://lkml.kernel.org/r/20170316125823.190342547@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

give up on gcc ilog2() constant optimizations

commit 474c90156c8dcc2fa815e6716cc9394d7930cb9c upstream.

gcc-7 has an "optimization" pass that completely screws up, and
generates the code expansion for the (impossible) case of calling
ilog2() with a zero constant, even when the code gcc compiles does not
actually have a zero constant.

And we try to generate a compile-time error for anybody doing ilog2() on
a constant where that doesn't make sense (be it zero or negative).  So
now gcc7 will fail the build due to our sanity checking, because it
created that constant-zero case that didn't actually exist in the source
code.

There's a whole long discussion on the kernel mailing about how to work
around this gcc bug.  The gcc people themselevs have discussed their
"feature" in

   https://gcc.gnu.org/bugzilla/show_bug.cgi?id=72785

but it's all water under the bridge, because while it looked at one
point like it would be solved by the time gcc7 was released, that was
not to be.

So now we have to deal with this compiler braindamage.

And the only simple approach seems to be to just delete the code that
tries to warn about bad uses of ilog2().

So now "ilog2()" will just return 0 not just for the value 1, but for
any non-positive value too.

It's not like I can recall anybody having ever actually tried to use
this function on any invalid value, but maybe the sanity check just
meant that such code never made it out in public.

Reported-by: Laura Abbott <labbott@redhat.com>
Cc: John Stultz <john.stultz@linaro.org>,
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kernek/fork.c: allocate idle task for a CPU always on its local node

commit 725fc629ff2545b061407305ae51016c9f928fce upstream.

Linux preallocates the task structs of the idle tasks for all possible
CPUs.  This currently means they all end up on node 0.  This also
implies that the cache line of MWAIT, which is around the flags field in
the task struct, are all located in node 0.

We see a noticeable performance improvement on Knights Landing CPUs when
the cache lines used for MWAIT are located in the local nodes of the
CPUs using them.  I would expect this to give a (likely slight)
improvement on other systems too.

The patch implements placing the idle task in the node of its CPUs, by
passing the right target node to copy_process()

[akpm@linux-foundation.org: use NUMA_NO_NODE, not a bare -1]
Link: http://lkml.kernel.org/r/1463492694-15833-1-git-send-email-andi@firstfloor.org
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hv_netvsc: use skb_get_hash() instead of a homegrown implementation

commit 757647e10e55c01fb7a9c4356529442e316a7c72 upstream.

Recent changes to 'struct flow_keys' (e.g commit d34af823ff40 ("net: Add
VLAN ID to flow_keys")) introduced a performance regression in netvsc
driver. Is problem is, however, not the above mentioned commit but the
fact that netvsc_set_hash() function did some assumptions on the struct
flow_keys data layout and this is wrong.

Get rid of netvsc_set_hash() by switching to skb_get_hash(). This change
will also imply switching to Jenkins hash from the currently used Toeplitz
but it seems there is no good excuse for Toeplitz to stay.

Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm_tis: Use devm_free_irq not free_irq

commit 727f28b8ca24a581c7bd868326b8cea1058c720a upstream.

The interrupt is always allocated with devm_request_irq so it
must always be freed with devm_free_irq.

Fixes: 448e9c55c12d ("tpm_tis: verify interrupt during init")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: add missing irq.h include

commit e9c5e7402dad6f4f04c2430db6f283512bcd4392 upstream.

this fixes the build on arm.

Signed-off-by: Dave Airlie <airlied@redhat.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/pci: fix use after free in dma_init

commit dba599091c191d209b1499511a524ad9657c0e5a upstream.

After a failure during registration of the dma_table (because of the
function being in error state) we free its memory but don't reset the
associated pointer to zero.

When we then receive a notification from firmware (about the function
being in error state) we'll try to walk and free the dma_table again.

Fix this by resetting the dma_table pointer. In addition to that make
sure that we free the iommu_bitmap when appropriate.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: PPC: Book3S PR: Fix illegal opcode emulation

commit 708e75a3ee750dce1072134e630d66c4e6eaf63c upstream.

If kvmppc_handle_exit_pr() calls kvmppc_emulate_instruction() to emulate
one instruction (in the BOOK3S_INTERRUPT_H_EMUL_ASSIST case), it calls
kvmppc_core_queue_program() afterwards if kvmppc_emulate_instruction()
returned EMULATE_FAIL, so the guest gets an program interrupt for the
illegal opcode.
However, the kvmppc_emulate_instruction() also tried to inject a
program exception for this already, so the program interrupt gets
injected twice and the return address in srr0 gets destroyed.
All other callers of kvmppc_emulate_instruction() are also injecting
a program interrupt, and since the callers have the right knowledge
about the srr1 flags that should be used, it is the function
kvmppc_emulate_instruction() that should _not_ inject program
interrupts, so remove the kvmppc_core_queue_program() here.

This fixes the issue discovered by Laurent Vivier with kvm-unit-tests
where the logs are filled with these messages when the test tries
to execute an illegal instruction:

     Couldn't emulate instruction 0x00000000 (op 0 xop 0)
     kvmppc_handle_exit_pr: emulation at 700 failed (00000000)

Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Tested-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/qspinlock: Don't kick CPU if IRQ is not initialized

commit 707e59ba494372a90d245f18b0c78982caa88e48 upstream.

The following commit:

  1fb3a8b2cfb2 ("xen/spinlock: Fix locking path engaging too soon under PVHVM.")

... moved the initalization of the kicker interrupt until after
native_cpu_up() is called.

However, when using qspinlocks, a CPU may try to kick another CPU that is
spinning (because it has not yet initialized its kicker interrupt), resulting
in the following crash during boot:

  kernel BUG at /build/linux-Ay7j_C/linux-4.4.0/drivers/xen/events/events_base.c:1210!
  invalid opcode: 0000 [#1] SMP
  ...
  RIP: 0010:[<ffffffff814c97c9>]  [<ffffffff814c97c9>] xen_send_IPI_one+0x59/0x60
  ...
  Call Trace:
   [<ffffffff8102be9e>] xen_qlock_kick+0xe/0x10
   [<ffffffff810cabc2>] __pv_queued_spin_unlock+0xb2/0xf0
   [<ffffffff810ca6d1>] ? __raw_callee_save___pv_queued_spin_unlock+0x11/0x20
   [<ffffffff81052936>] ? check_tsc_warp+0x76/0x150
   [<ffffffff81052aa6>] check_tsc_sync_source+0x96/0x160
   [<ffffffff81051e28>] native_cpu_up+0x3d8/0x9f0
   [<ffffffff8102b315>] xen_hvm_cpu_up+0x35/0x80
   [<ffffffff8108198c>] _cpu_up+0x13c/0x180
   [<ffffffff81081a4a>] cpu_up+0x7a/0xa0
   [<ffffffff81f80dfc>] smp_init+0x7f/0x81
   [<ffffffff81f5a121>] kernel_init_freeable+0xef/0x212
   [<ffffffff81817f30>] ? rest_init+0x80/0x80
   [<ffffffff81817f3e>] kernel_init+0xe/0xe0
   [<ffffffff8182488f>] ret_from_fork+0x3f/0x70
   [<ffffffff81817f30>] ? rest_init+0x80/0x80

To fix this, only send the kick if the target CPU's interrupt has been
initialized. This check isn't racy, because the target is waiting for
the spinlock, so it won't have initialized the interrupt in the
meantime.

Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Drivers: hv: avoid vfree() on crash

commit a9f61ca793becabdefab03b77568d6c6f8c1bc79 upstream.

When we crash from NMI context (e.g. after NMI injection from host when
'sysctl -w kernel.unknown_nmi_panic=1' is set) we hit

    kernel BUG at mm/vmalloc.c:1530!

as vfree() is denied. While the issue could be solved with in_nmi() check
instead I opted for skipping vfree on all sorts of crashes to reduce the
amount of work which can cause consequent crashes. We don't really need to
free anything on crash.

Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Drivers: hv: balloon: don't crash when memory is added in non-sorted order

commit 77c0c9735bc0ba5898e637a3a20d6bcb50e3f67d upstream.

When we iterate through all HA regions in handle_pg_range() we have an
assumption that all these regions are sorted in the list and the
'start_pfn >= has->end_pfn' check is enough to find the proper region.
Unfortunately it's not the case with WS2016 where host can hot-add regions
in a different order. We end up modifying the wrong HA region and crashing
later on pages online. Modify the check to make sure we found the region
we were searching for while iterating. Fix the same check in pfn_covered()
as well.

Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: cherryview: Do not mask all interrupts in probe

commit bcb48cca23ec9852739e4a464307fa29515bbe48 upstream.

The Cherryview GPIO controller has 8 or 16 wires connected to the I/O-APIC
which can be used directly by the platform/BIOS or drivers. One such wire
is used as SCI (System Control Interrupt) which ACPI depends on to be able
to trigger GPEs (General Purpose Events).

The pinctrl driver itself uses another IRQ resource which is wire OR of all
the 8 (or 16) wires and follows what BIOS has programmed to the IntSel
register of each pin.

Currently the driver masks all interrupts at probe time and this prevents
these direct interrupts from working as expected. The reason for this is
that some early stage prototypes had some pins misconfigured causing lots
of spurious interrupts.

We fix this by leaving the interrupt mask untouched. This allows SCI and
other direct interrupts work properly. What comes to the possible spurious
interrupts we switch the default handler to be handle_bad_irq() instead of
handle_simple_irq() (which was not correct anyway).

Reported-by: Yu C Chen <yu.c.chen@intel.com>
Reported-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPI / video: skip evaluating _DOD when it does not exist

commit e34fbbac669de0b7fb7803929d0477f35f6e2833 upstream.

Some system supports hybrid graphics and its discrete VGA
does not have any connectors and therefore has no _DOD method.

Signed-off-by: Alex Hung <alex.hung@canonical.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cxlflash: Increase cmd_per_lun for better throughput

commit 83430833b4d4a9c9b23964babbeb1f36450f8136 upstream.

With the current value of cmd_per_lun at 16, the throughput
over a single adapter is limited to around 150kIOPS.

Increase the value of cmd_per_lun to 256 to improve
throughput. With this change a single adapter is able to
attain close to the maximum throughput (380kIOPS).
Also change the number of RRQ entries that can be queued.

Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: mcryptd - Fix load failure

commit ddef482420b1ba8ec45e6123a7e8d3f67b21e5e3 upstream.

mcryptd_create_hash() fails by returning -EINVAL, causing any
driver using mcryptd to fail to load. It is because it needs
to set its statesize properly.

Signed-off-by: Rui Wang <rui.y.wang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: cryptd - Assign statesize properly

commit 1a07834024dfca5c4bed5de8f8714306e0a11836 upstream.

cryptd_create_hash() fails by returning -EINVAL.  It is because after
8996eafdc ("crypto: ahash - ensure statesize is non-zero") all ahash
drivers must have a non-zero statesize.

This patch fixes the problem by properly assigning the statesize.

Signed-off-by: Rui Wang <rui.y.wang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: ghash-clmulni - Fix load failure

commit 3a020a723c65eb8ffa7c237faca26521a024e582 upstream.

ghash_clmulni_intel fails to load on Linux 4.3+ with the following message:
"modprobe: ERROR: could not insert 'ghash_clmulni_intel': Invalid argument"

After 8996eafdc ("crypto: ahash - ensure statesize is non-zero") all ahash
drivers are required to implement import()/export(), and must have a non-
zero statesize.

This patch has been tested with the algif_hash interface. The calculated
digest values, after several rounds of import()s and export()s, match those
calculated by tcrypt.

Signed-off-by: Rui Wang <rui.y.wang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: don't free bandwidth_mutex too early

commit ab2a4bf83902c170d29ba130a8abb5f9d90559e1 upstream.

The USB core contains a bug that can show up when a USB-3 host
controller is removed.  If the primary (USB-2) hcd structure is
released before the shared (USB-3) hcd, the core will try to do a
double-free of the common bandwidth_mutex.

The problem was described in graphical form by Chung-Geol Kim, who
first reported it:

=================================================
     At *remove USB(3.0) Storage
     sequence <1> --> <5> ((Problem Case))
=================================================
                                  VOLD
------------------------------------|------------
                                 (uevent)
                            ________|_________
                           |<1>               |
                           |dwc3_otg_sm_work  |
                           |usb_put_hcd       |
                           |peer_hcd(kref=2)|
                           |__________________|
                            ________|_________
                           |<2>               |
                           |New USB BUS #2    |
                           |                  |
                           |peer_hcd(kref=1)  |
                           |                  |
                         --(Link)-bandXX_mutex|
                         | |__________________|
                         |
    ___________________  |
   |<3>                | |
   |dwc3_otg_sm_work   | |
   |usb_put_hcd        | |
   |primary_hcd(kref=1)| |
   |___________________| |
    _________|_________  |
   |<4>                | |
   |New USB BUS #1     | |
   |hcd_release        | |
   |primary_hcd(kref=0)| |
   |                   | |
   |bandXX_mutex(free) |<-
   |___________________|
                               (( VOLD ))
                            ______|___________
                           |<5>               |
                           |      SCSI        |
                           |usb_put_hcd       |
                           |peer_hcd(kref=0)  |
                           |*hcd_release      |
                           |bandXX_mutex(free*)|<- double free
                           |__________________|

=================================================

This happens because hcd_release() frees the bandwidth_mutex whenever
it sees a primary hcd being released (which is not a very good idea
in any case), but in the course of releasing the primary hcd, it
changes the pointers in the shared hcd in such a way that the shared
hcd will appear to be primary when it gets released.

This patch fixes the problem by changing hcd_release() so that it
deallocates the bandwidth_mutex only when the _last_ hcd structure
referencing it is released.  The patch also removes an unnecessary
test, so that when an hcd is released, both the shared_hcd and
primary_hcd pointers in the hcd's peer will be cleared.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Chung-Geol Kim <chunggeol.kim@samsung.com>
Tested-by: Chung-Geol Kim <chunggeol.kim@samsung.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: core: hub: hub_port_init lock controller instead of bus

commit feb26ac31a2a5cb88d86680d9a94916a6343e9e6 upstream.

The XHCI controller presents two USB buses to the system - one for USB2
and one for USB3. The hub init code (hub_port_init) is reentrant but
only locks one bus per thread, leading to a race condition failure when
two threads attempt to simultaneously initialise a USB2 and USB3 device:

[    8.034843] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[   13.183701] usb 3-3: device descriptor read/all, error -110

On a test system this failure occurred on 6% of all boots.

The call traces at the point of failure are:

Call Trace:
 [<ffffffff81b9bab7>] schedule+0x37/0x90
 [<ffffffff817da7cd>] usb_kill_urb+0x8d/0xd0
 [<ffffffff8111e5e0>] ? wake_up_atomic_t+0x30/0x30
 [<ffffffff817dafbe>] usb_start_wait_urb+0xbe/0x150
 [<ffffffff817db10c>] usb_control_msg+0xbc/0xf0
 [<ffffffff817d07de>] hub_port_init+0x51e/0xb70
 [<ffffffff817d4697>] hub_event+0x817/0x1570
 [<ffffffff810f3e6f>] process_one_work+0x1ff/0x620
 [<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620
 [<ffffffff810f4684>] worker_thread+0x64/0x4b0
 [<ffffffff810f4620>] ? rescuer_thread+0x390/0x390
 [<ffffffff810fa7f5>] kthread+0x105/0x120
 [<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
 [<ffffffff81ba183f>] ret_from_fork+0x3f/0x70
 [<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200

Call Trace:
 [<ffffffff817fd36d>] xhci_setup_device+0x53d/0xa40
 [<ffffffff817fd87e>] xhci_address_device+0xe/0x10
 [<ffffffff817d047f>] hub_port_init+0x1bf/0xb70
 [<ffffffff811247ed>] ? trace_hardirqs_on+0xd/0x10
 [<ffffffff817d4697>] hub_event+0x817/0x1570
 [<ffffffff810f3e6f>] process_one_work+0x1ff/0x620
 [<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620
 [<ffffffff810f4684>] worker_thread+0x64/0x4b0
 [<ffffffff810f4620>] ? rescuer_thread+0x390/0x390
 [<ffffffff810fa7f5>] kthread+0x105/0x120
 [<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
 [<ffffffff81ba183f>] ret_from_fork+0x3f/0x70
 [<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200

Which results from the two call chains:

hub_port_init
 usb_get_device_descriptor
  usb_get_descriptor
   usb_control_msg
    usb_internal_control_msg
     usb_start_wait_urb
      usb_submit_urb / wait_for_completion_timeout / usb_kill_urb

hub_port_init
 hub_set_address
  xhci_address_device
   xhci_setup_device

Mathias Nyman explains the current behaviour violates the XHCI spec:

 hub_port_reset() will end up moving the corresponding xhci device slot
 to default state.

 As hub_port_reset() is called several times in hub_port_init() it
 sounds reasonable that we could end up with two threads having their
 xhci device slots in default state at the same time, which according to
 xhci 4.5.3 specs still is a big no no:

 "Note: Software shall not transition more than one Device Slot to the
  Default State at a time"

 So both threads fail at their next task after this.
 One fails to read the descriptor, and the other fails addressing the
 device.

Fix this in hub_port_init by locking the USB controller (instead of an
individual bus) to prevent simultaneous initialisation of both buses.

Fixes: 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel")
Link: https://lkml.org/lkml/2016/2/8/312
Link: https://lkml.org/lkml/2016/2/4/748
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
 [sumits: minor merge conflict resolution for linux-4.4.y]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.4.56

futex: Add missing error handling to FUTEX_REQUEUE_PI

commit 9bbb25afeb182502ca4f2c4f3f88af0681b34cae upstream.

Thomas spotted that fixup_pi_state_owner() can return errors and we
fail to unlock the rt_mutex in that case.

Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Cc: juri.lelli@arm.com
Cc: bigeasy@linutronix.de
Cc: xlpang@redhat.com
Cc: rostedt@goodmis.org
Cc: mathieu.desnoyers@efficios.com
Cc: jdesfossez@efficios.com
Cc: dvhart@infradead.org
Cc: bristot@redhat.com
Link: http://lkml.kernel.org/r/20170304093558.867401760@infradead.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

futex: Fix potential use-after-free in FUTEX_REQUEUE_PI

commit c236c8e95a3d395b0494e7108f0d41cf36ec107c upstream.

While working on the futex code, I stumbled over this potential
use-after-free scenario. Dmitry triggered it later with syzkaller.

pi_mutex is a pointer into pi_state, which we drop the reference on in
unqueue_me_pi(). So any access to that pointer after that is bad.

Since other sites already do rt_mutex_unlock() with hb->lock held, see
for example futex_lock_pi(), simply move the unlock before
unqueue_me_pi().

Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Cc: juri.lelli@arm.com
Cc: bigeasy@linutronix.de
Cc: xlpang@redhat.com
Cc: rostedt@goodmis.org
Cc: mathieu.desnoyers@efficios.com
Cc: jdesfossez@efficios.com
Cc: dvhart@infradead.org
Cc: bristot@redhat.com
Link: http://lkml.kernel.org/r/20170304093558.801744246@infradead.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/perf: Fix CR4.PCE propagation to use active_mm instead of mm

commit 5dc855d44c2ad960a86f593c60461f1ae1566b6d upstream.

If one thread mmaps a perf event while another thread in the same mm
is in some context where active_mm != mm (which can happen in the
scheduler, for example), refresh_pce() would write the wrong value
to CR4.PCE.  This broke some PAPI tests.

Reported-and-tested-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes: 7911d3f7af14 ("perf/x86: Only allow rdpmc if a perf_event is mapped")
Link: http://lkml.kernel.org/r/0c5b38a76ea50e405f9abe07a13dfaef87c173a1.1489694270.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/kasan: Fix boot with KASAN=y and PROFILE_ANNOTATED_BRANCHES=y

commit be3606ff739d1c1be36389f8737c577ad87e1f57 upstream.

The kernel doesn't boot with both PROFILE_ANNOTATED_BRANCHES=y and KASAN=y
options selected. With branch profiling enabled we end up calling
ftrace_likely_update() before kasan_early_init(). ftrace_likely_update() is
built with KASAN instrumentation, so calling it before kasan has been
initialized leads to crash.

Use DISABLE_BRANCH_PROFILING define to make sure that we don't call
ftrace_likely_update() from early code before kasan_early_init().

Fixes: ef7f0d6a6ca8 ("x86_64: add KASan support")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: kasan-dev@googlegroups.com
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: lkp@01.org
Cc: Dmitry Vyukov <dvyukov@google.com>
Link: http://lkml.kernel.org/r/20170313163337.1704-1-aryabinin@virtuozzo.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fscrypto: lock inode while setting encryption policy

commit 8906a8223ad4909b391c5628f7991ebceda30e52 upstream.

i_rwsem needs to be acquired while setting an encryption policy so that
concurrent calls to FS_IOC_SET_ENCRYPTION_POLICY are correctly
serialized (especially the ->get_context() + ->set_context() pair), and
so that new files cannot be created in the directory during or after the
->empty_dir() check.

Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Richard Weinberger <richard@nod.at>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fscrypt: fix renaming and linking special files

commit 42d97eb0ade31e1bc537d086842f5d6e766d9d51 upstream.

Attempting to link a device node, named pipe, or socket file into an
encrypted directory through rename(2) or link(2) always failed with
EPERM.  This happened because fscrypt_has_permitted_context() saw that
the file was unencrypted and forbid creating the link.  This behavior
was unexpected because such files are never encrypted; only regular
files, directories, and symlinks can be encrypted.

To fix this, make fscrypt_has_permitted_context() always return true on
special files.

This will be covered by a test in my encryption xfstests patchset.

Fixes: 9bd8212f981e ("ext4 crypto: add encryption policy and password salt support")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net sched actions: decrement module reference count after table flush.

[ Upstream commit edb9d1bff4bbe19b8ae0e71b1f38732591a9eeb2 ]

When tc actions are loaded as a module and no actions have been installed,
flushing them would result in actions removed from the memory, but modules
reference count not being decremented, so that the modules would not be
unloaded.

Following is example with GACT action:

% sudo modprobe act_gact
% lsmod
Module                  Size  Used by
act_gact               16384  0
%
% sudo tc actions ls action gact
%
% sudo tc actions flush action gact
% lsmod
Module                  Size  Used by
act_gact               16384  1
% sudo tc actions flush action gact
% lsmod
Module                  Size  Used by
act_gact               16384  2
% sudo rmmod act_gact
rmmod: ERROR: Module act_gact is in use
....

After the fix:
% lsmod
Module                  Size  Used by
act_gact               16384  0
%
% sudo tc actions add action pass index 1
% sudo tc actions add action pass index 2
% sudo tc actions add action pass index 3
% lsmod
Module                  Size  Used by
act_gact               16384  3
%
% sudo tc actions flush action gact
% lsmod
Module                  Size  Used by
act_gact               16384  0
%
% sudo tc actions flush action gact
% lsmod
Module                  Size  Used by
act_gact               16384  0
% sudo rmmod act_gact
% lsmod
Module                  Size  Used by
%

Fixes: f97017cdefef ("net-sched: Fix actions flushing")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dccp: fix memory leak during tear-down of unsuccessful connection request

[ Upstream commit 72ef9c4125c7b257e3a714d62d778ab46583d6a3 ]

This patch fixes a memory leak, which happens if the connection request
is not fulfilled between parsing the DCCP options and handling the SYN
(because e.g. the backlog is full), because we forgot to free the
list of ack vectors.

Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dccp/tcp: fix routing redirect race

[ Upstream commit 45caeaa5ac0b4b11784ac6f932c0ad4c6b67cda0 ]

As Eric Dumazet pointed out this also needs to be fixed in IPv6.
v2: Contains the IPv6 tcp/Ipv6 dccp patches as well.

We have seen a few incidents lately where a dst_enty has been freed
with a dangling TCP socket reference (sk->sk_dst_cache) pointing to that
dst_entry. If the conditions/timings are right a crash then ensues when the
freed dst_entry is referenced later on. A Common crashing back trace is:

 #8 [] page_fault at ffffffff8163e648
    [exception RIP: __tcp_ack_snd_check+74]
.
.
 #9 [] tcp_rcv_established at ffffffff81580b64
#10 [] tcp_v4_do_rcv at ffffffff8158b54a
#11 [] tcp_v4_rcv at ffffffff8158cd02
#12 [] ip_local_deliver_finish at ffffffff815668f4
#13 [] ip_local_deliver at ffffffff81566bd9
#14 [] ip_rcv_finish at ffffffff8156656d
#15 [] ip_rcv at ffffffff81566f06
#16 [] __netif_receive_skb_core at ffffffff8152b3a2
#17 [] __netif_receive_skb at ffffffff8152b608
#18 [] netif_receive_skb at ffffffff8152b690
#19 [] vmxnet3_rq_rx_complete at ffffffffa015eeaf [vmxnet3]
#20 [] vmxnet3_poll_rx_only at ffffffffa015f32a [vmxnet3]
#21 [] net_rx_action at ffffffff8152bac2
#22 [] __do_softirq at ffffffff81084b4f
#23 [] call_softirq at ffffffff8164845c
#24 [] do_softirq at ffffffff81016fc5
#25 [] irq_exit at ffffffff81084ee5
#26 [] do_IRQ at ffffffff81648ff8

Of course it may happen with other NIC drivers as well.

It's found the freed dst_entry here:

 224 static bool tcp_in_quickack_mode(struct sock *sk)↩
 225 {↩
 226 ▹       const struct inet_connection_sock *icsk = inet_csk(sk);↩
 227 ▹       const struct dst_entry *dst = __sk_dst_get(sk);↩
 228 ↩
 229 ▹       return (dst && dst_metric(dst, RTAX_QUICKACK)) ||↩
 230 ▹       ▹       (icsk->icsk_ack.quick && !icsk->icsk_ack.pingpong);↩
 231 }↩

But there are other backtraces attributed to the same freed dst_entry in
netfilter code as well.

All the vmcores showed 2 significant clues:

- Remote hosts behind the default gateway had always been redirected to a
different gateway. A rtable/dst_entry will be added for that host. Making
more dst_entrys with lower reference counts. Making this more probable.

- All vmcores showed a postitive LockDroppedIcmps value, e.g:

LockDroppedIcmps                  267

A closer look at the tcp_v4_err() handler revealed that do_redirect() will run
regardless of whether user space has the socket locked. This can result in a
race condition where the same dst_entry cached in sk->sk_dst_entry can be
decremented twice for the same socket via:

do_redirect()->__sk_dst_check()-> dst_release().

Which leads to the dst_entry being prematurely freed with another socket
pointing to it via sk->sk_dst_cache and a subsequent crash.

To fix this skip do_redirect() if usespace has the socket locked. Instead let
the redirect take place later when user space does not have the socket
locked.

The dccp/IPv6 code is very similar in this respect, so fixing it there too.

As Eric Garver pointed out the following commit now invalidates routes. Which
can set the dst->obsolete flag so that ipv4_dst_check() returns null and
triggers the dst_release().

Fixes: ceb3320610d6 ("ipv4: Kill routes during PMTU/redirect updates.")
Cc: Eric Garver <egarver@redhat.com>
Cc: Hannes Sowa <hsowa@redhat.com>
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bridge: drop netfilter fake rtable unconditionally

[ Upstream commit a13b2082ece95247779b9995c4e91b4246bed023 ]

Andreas reports kernel oops during rmmod of the br_netfilter module.
Hannes debugged the oops down to a NULL rt6info->rt6i_indev.

Problem is that br_netfilter has the nasty concept of adding a fake
rtable to skb->dst; this happens in a br_netfilter prerouting hook.

A second hook (in bridge LOCAL_IN) is supposed to remove these again
before the skb is handed up the stack.

However, on module unload hooks get unregistered which means an
skb could traverse the prerouting hook that attaches the fake_rtable,
while the 'fake rtable remove' hook gets removed from the hooklist
immediately after.

Fixes: 34666d467cbf1e2e3c7 ("netfilter: bridge: move br_netfilter out of the core")
Reported-by: Andreas Karis <akaris@redhat.com>
Debugged-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: avoid write to a possibly cloned skb

[ Upstream commit 79e49503efe53a8c51d8b695bedc8a346c5e4a87 ]

ip6_fragment, in case skb has a fraglist, checks if the
skb is cloned.  If it is, it will move to the 'slow path' and allocates
new skbs for each fragment.

However, right before entering the slowpath loop, it updates the
nexthdr value of the last ipv6 extension header to NEXTHDR_FRAGMENT,
to account for the fragment header that will be inserted in the new
ipv6-fragment skbs.

In case original skb is cloned this munges nexthdr value of another
skb.  Avoid this by doing the nexthdr update for each of the new fragment
skbs separately.

This was observed with tcpdump on a bridge device where netfilter ipv6
reassembly is active:  tcpdump shows malformed fragment headers as
the l4 header (icmpv6, tcp, etc). is decoded as a fragment header.

Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Andreas Karis <akaris@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: make ECMP route replacement less greedy

[ Upstream commit 67e194007be08d071294456274dd53e0a04fdf90 ]

Commit 27596472473a ("ipv6: fix ECMP route replacement") introduced a
loop that removes all siblings of an ECMP route that is being
replaced. However, this loop doesn't stop when it has replaced
siblings, and keeps removing other routes with a higher metric.
We also end up triggering the WARN_ON after the loop, because after
this nsiblings < 0.

Instead, stop the loop when we have taken care of all routes with the
same metric as the route being replaced.

  Reproducer:
  ===========
    #!/bin/sh

    ip netns add ns1
    ip netns add ns2
    ip -net ns1 link set lo up

    for x in 0 1 2 ; do
        ip link add veth$x netns ns2 type veth peer name eth$x netns ns1
        ip -net ns1 link set eth$x up
        ip -net ns2 link set veth$x up
    done

    ip -net ns1 -6 r a 2000::/64 nexthop via fe80::0 dev eth0 \
            nexthop via fe80::1 dev eth1 nexthop via fe80::2 dev eth2
    ip -net ns1 -6 r a 2000::/64 via fe80::42 dev eth0 metric 256
    ip -net ns1 -6 r a 2000::/64 via fe80::43 dev eth0 metric 2048

    echo "before replace, 3 routes"
    ip -net ns1 -6 r | grep -v '^fe80\|^ff00'
    echo

    ip -net ns1 -6 r c 2000::/64 nexthop via fe80::4 dev eth0 \
            nexthop via fe80::5 dev eth1 nexthop via fe80::6 dev eth2

    echo "after replace, only 2 routes, metric 2048 is gone"
    ip -net ns1 -6 r | grep -v '^fe80\|^ff00'

Fixes: 27596472473a ("ipv6: fix ECMP route replacement")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>