OSDN Git Service
Simon Wunderlich [Mon, 1 Oct 2018 14:26:59 +0000 (17:26 +0300)]
ath9k: fix reporting calculated new FFT upper max
Since the debug print code is outside of the loop, it shouldn't use the loop
iterator anymore but instead print the found maximum index.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simon Wunderlich [Mon, 1 Oct 2018 14:26:56 +0000 (17:26 +0300)]
ath9k: FFT magnitude check: don't consider lower 3 data bits
There were a lot of Magnitude Mismatch while getting FFT samples on my
hardware (Atheros AR9462. I've compared the reported magnitude with
the data in the FFT bin, and the FFT bin was less accurate:
[ 5395.193030] ath: phy0: FFT HT20 frame: max mag 0x89,max_mag_idx 28,
,magnitude 0x89 max_exp 0, data[28] = 0x88
[ 5395.194525] ath: phy0: FFT HT20 frame: max mag 0x89,max_mag_idx 28,
,magnitude 0x89 max_exp 0, data[28] = 0x88
[ 5395.196012] ath: phy0: FFT HT20 frame: max mag 0x88,max_mag_idx 28,
,magnitude 0x88 max_exp 0, data[28] = 0x88
[ 5395.197509] ath: phy0: FFT HT20 frame: max mag 0x6C,max_mag_idx 28,
,magnitude 0x6C max_exp 0, data[28] = 0x68
[ 5395.199015] ath: phy0: FFT HT20 frame: max mag 0x78,max_mag_idx 28,
,magnitude 0x78 max_exp 0, data[28] = 0x78
[ 5395.200497] ath: phy0: FFT HT20 frame: max mag 0xA1,max_mag_idx 28,
,magnitude 0xA1 max_exp 0, data[28] = 0xA0
[ 5395.202011] ath: phy0: FFT HT20 frame: max mag 0x91,max_mag_idx 28,
,magnitude 0x91 max_exp 0, data[28] = 0x90
[ 5395.203482] ath: phy0: FFT HT20 frame: max mag 0x89,max_mag_idx 28,
,magnitude 0x89 max_exp 0, data[28] = 0x88
[ 5395.204999] ath: phy0: FFT HT20 frame: max mag 0x27,max_mag_idx 4,
,magnitude 0x27 max_exp 0, data[4] = 0x20
[ 5395.206461] ath: phy0: FFT HT20 frame: max mag 0x41,max_mag_idx 28,
,magnitude 0x41 max_exp 0, data[28] = 0x40
[ 5395.207977] ath: phy0: FFT HT20 frame: max mag 0x51,max_mag_idx 28,
,magnitude 0x51 max_exp 0, data[28] = 0x50
[ 5395.209454] ath: phy0: FFT HT20 frame: max mag 0x53,max_mag_idx 28,
,magnitude 0x53 max_exp 0, data[28] = 0x50
[ 5395.210940] ath: phy0: FFT HT20 frame: max mag 0x40,max_mag_idx 28,
,magnitude 0x40 max_exp 0, data[28] = 0x40
[ 5395.212441] ath: phy0: FFT HT20 frame: max mag 0x59,max_mag_idx 28,
,magnitude 0x59 max_exp 0, data[28] = 0x58
[ 5395.213932] ath: phy0: FFT HT20 frame: max mag 0x53,max_mag_idx 28,
,magnitude 0x53 max_exp 0, data[28] = 0x50
[ 5395.215428] ath: phy0: FFT HT20 frame: max mag 0x7D,max_mag_idx 28,
,magnitude 0x7D max_exp 0, data[28] = 0x78
[ 5395.216910] ath: phy0: FFT HT20 frame: max mag 0x8C,max_mag_idx 28,
,magnitude 0x8C max_exp 0, data[28] = 0x88
[ 5395.218413] ath: phy0: FFT HT20 frame: max mag 0x7B,max_mag_idx 28,
,magnitude 0x7B max_exp 0, data[28] = 0x78
[ 5395.219900] ath: phy0: FFT HT20 frame: max mag 0x43,max_mag_idx 28,
,magnitude 0x43 max_exp 0, data[28] = 0x40
It seems like the lower 3 bits on my hardware are always zeroed, but the
magnitude matches otherwise. Therefore, let's not make the magnitude
check so strict so we can get those samples released to userspace.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simon Wunderlich [Mon, 1 Oct 2018 14:26:51 +0000 (17:26 +0300)]
ath9k: fix and simplify FFT max index retrieval
FFT max index retrieval was not retrieved correctly for HT20/HT40 FFT
frames. Fixing the retrieval allows us to remove the fixup function as
well. While at it, split the spectral_max_index function into versions
for ht20 and ht40 to simplify the code.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simon Wunderlich [Mon, 1 Oct 2018 14:26:46 +0000 (17:26 +0300)]
ath9k: return when short FFT frame was handled
With the loop break like this, there are false "FFT report truncated"
messages because the iterator is not advanced as the check expects.
Instead, just return, for a single frame there is nothing left to be
done anyways.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simon Wunderlich [Mon, 1 Oct 2018 14:26:42 +0000 (17:26 +0300)]
ath9k: add counters for good and errorneous FFT/spectral frames
This is helpful to see whether spectral samples get discarded.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
YueHaibing [Tue, 11 Sep 2018 12:32:19 +0000 (12:32 +0000)]
wil6210: remove set but not used variable 'start'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/wil6210/pm.c: In function 'wil_suspend_keep_radio_on':
drivers/net/wireless/ath/wil6210/pm.c:193:16: warning:
variable 'start' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
YueHaibing [Mon, 10 Sep 2018 03:11:28 +0000 (11:11 +0800)]
ath9k: debug: remove set but not used variable 'fops_dump_nfcal'
'fops_dump_nfcal' is not used since commit
4447d815fd0f ("ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Louie Lu [Thu, 6 Sep 2018 03:53:26 +0000 (11:53 +0800)]
ath9k: add reset for airtime station debugfs
Let user can reset station airtime status by debugfs, it will
reset all airtime deficit to ATH_AIRTIME_QUANTUM and reset rx/tx
airtime accumulate to 0.
Signed-off-by: Louie Lu <git@louie.lu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Thu, 20 Sep 2018 05:04:26 +0000 (10:34 +0530)]
ath10k: disable napi before resource cleanup to avoid "use after free"
CE buffers are cleaned up prior to napi disable and this is causing
NULL pointer dereference due to "use after free".
Disable napi before resource cleanup to avoid "use after free".
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Thu, 20 Sep 2018 05:04:25 +0000 (10:34 +0530)]
ath10k: move napi_enable to hif_start for consistent pairing
There is unbalanced napi_{enable,disable}() behavior as they
are being called from hif_snoc_{power_up/stop).
The fix is to call napi_enable() from ath10k_snoc_hif_start()
so that it matches with napi_disable() being called from
ath10k_snoc_hif_stop().
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Maharaja Kennadyrajan [Tue, 18 Sep 2018 12:07:26 +0000 (17:37 +0530)]
ath10k: advertize beacon_int_min_gcd as 100 while bring up multi vaps
With the latest firmware design, the beacon interval should be
greater than 100 to bring the multiple vaps.
Set beacon_int_min_gcd to 100, when the wmi service
WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT is enabled
in the firmware. If not, beacon_int_min_gcd will be set
to the default value 1.
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00015
Tested in QCA9888 with firmware ver 10.4-3.5.1-0005
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Maharaja Kennadyrajan [Tue, 18 Sep 2018 06:34:27 +0000 (12:04 +0530)]
ath10k: add debugfs support to get power save state change of STA
This patch helps to get the power save state change of each peer
connected to the AP. With WMI_10_4_PEER_STA_PS_STATECHG_EVENTID
event, ps state of each peer is reported to user space via
debugfs.
Use the below command to get the ps state of each sta:
cat /sys/kernel/debug/ieee80211/phyX/netdev::wlanX/stations/
XX:XX:XX:XX:XX:XX/peer_ps_state
If STA is in power save state, we get the peer_ps_state value as 1.
if STA is not in power save state, we get the peer_ps_state value as 0.
If ps_state event is disabled, we get the peer_ps_state value as 2.
We can enable/disable the ps_state events using the debugfs flag
"ps_state_enable"
echo Y > /sys/kernel/debug/ieee80211/phyX/ath10k/ps_state_enable
Y = 1 to enable and Y = 0 to disable
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
YueHaibing [Thu, 13 Sep 2018 14:01:21 +0000 (22:01 +0800)]
ath10k: remove duplicated includes
remove duplicated include from ath10k driver.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sriram R [Mon, 10 Sep 2018 05:39:40 +0000 (11:09 +0530)]
ath10k: add support for configuring management packet rate
By default the firmware uses 1Mbps and 6Mbps rate for management packets
in 2G and 5G bands respectively. But when the user selects different
basic rates from the userspace, we need to send the management
packets at the lowest basic rate selected by the user.
This change makes use of WMI_VDEV_PARAM_MGMT_RATE param for configuring the
management packets rate to the firmware.
Chipsets Tested : QCA988X, QCA9887, QCA9984
FW Tested : 10.2.4-1.0-41, 10.4-3.6.104
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Stromdahl [Thu, 13 Sep 2018 14:45:06 +0000 (16:45 +0200)]
ath10k: remove num_peers in hw_params for most targets
>From commit "ath10k: add per target config of max_num_peers",
the num_peers value in struct ath10k_hw_params is used to override
the value obtained from the WMI op version in the firmware file.
Currently, only high latency devices (USB and SDIO) need to use this
value, since the value obtained from the WMI op version is not
applicable for these devices.
Many devices in ath10k_hw_params_list have the wrong value set.
An example of this is the QCA9880 hw2.0 chipset that had (before this
patch) num_peers set to TARGET_TLV_NUM_PEERS although the firmware
uses WMI version ATH10K_FW_WMI_OP_VERSION_10_2_4.
Using the wrong value for the QCA9880 chip results in a fw crash:
ath10k_pci 0000:01:00.0: firmware crashed! (guid
ddf39880-3e64-4edf-b4e4-
979d31724503)
ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 0
ath10k_pci 0000:01:00.0: firmware ver 10.2.4-1.0-00037 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32
a4a52adb
ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32
bebc7c08
ath10k_pci 0000:01:00.0: htt-ver 0.0 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
ath10k_pci 0000:01:00.0: firmware register dump:
ath10k_pci 0000:01:00.0: [00]: 0x4100016C 0x000015B3 0x009B54B7 0x00955B31
ath10k_pci 0000:01:00.0: [04]: 0x009B54B7 0x00060530 0x00000011 0x00400000
ath10k_pci 0000:01:00.0: [08]: 0x000001B8 0x00000007 0x00443138 0x00955A00
ath10k_pci 0000:01:00.0: [12]: 0x00000009 0x00000000 0x009B548E 0x009B54AB
ath10k_pci 0000:01:00.0: [16]: 0x00958080 0x0094078E 0x00000000 0x00000000
ath10k_pci 0000:01:00.0: [20]: 0x409B54B7 0x0040AC64 0x00400000 0x00000087
ath10k_pci 0000:01:00.0: [24]: 0x809A3831 0x0040ACC4 0x000001B1 0xC09B54B7
ath10k_pci 0000:01:00.0: [28]: 0x809A2F08 0x0040AD04 0x00410410 0x00000001
ath10k_pci 0000:01:00.0: [32]: 0x80988856 0x0040AD24 0x00410410 0x00000001
ath10k_pci 0000:01:00.0: [36]: 0x8098AF64 0x0040AD44 0x00410410 0x00000001
ath10k_pci 0000:01:00.0: [40]: 0x809B5DEC 0x0040AD84 0x00410410 0x00410FF4
ath10k_pci 0000:01:00.0: [44]: 0x809B1F20 0x0040ADA4 0x00400000 0x00416C54
ath10k_pci 0000:01:00.0: [48]: 0x809C0295 0x0040ADE4 0x0040AE08 0x00411DC8
ath10k_pci 0000:01:00.0: [52]: 0x809486FA 0x0040AE04 0x00000001 0x00000000
ath10k_pci 0000:01:00.0: [56]: 0x80948E2C 0x0040AEA4 0x0041F290 0x004123D4
ath10k_pci 0000:01:00.0: Copy Engine register dump:
ath10k_pci 0000:01:00.0: [00]: 0x00057400 10 10 3 3
ath10k_pci 0000:01:00.0: [01]: 0x00057800 3 3 8 9
ath10k_pci 0000:01:00.0: [02]: 0x00057c00 2 2 1 2
ath10k_pci 0000:01:00.0: [03]: 0x00058000 1 1 2 1
ath10k_pci 0000:01:00.0: [04]: 0x00058400 0 0 40 0
ath10k_pci 0000:01:00.0: [05]: 0x00058800 1 1 0 1
ath10k_pci 0000:01:00.0: [06]: 0x00058c00 0 0 0 0
ath10k_pci 0000:01:00.0: [07]: 0x00059000 0 0 0 0
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Stromdahl [Thu, 13 Sep 2018 14:45:05 +0000 (16:45 +0200)]
ath10k: add default value for num_peers in WMI TLV init
The hw_params value will only be used if it was explicitly set in the
global hw_params array.
This makes it possible to have the num_peers member unset.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Fri, 7 Sep 2018 17:21:57 +0000 (10:21 -0700)]
ath10k: utilize random MAC address if none is provided
Since commit
9d5804662ce1 ("ath10k: retrieve MAC address from system
firmware if provided"), we support pulling our MAC address from system
firmware. Along with this, we should admit that it's possible for system
firmware to be screwed up as well, omitting the MAC address there.
Provide a fallback, such that we choose a randomly-generated MAC
address, with the local assignment bit set.
This is not a preferred mode of operation and really should only serve
the purpose of keeping the system chugging along while someone figures
out what's wrong with the system. Grepping through other wireless
drivers shows very similar fallback logic though, so why not?
git grep eth_random_addr drivers/net/wireless/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rakesh Pillai [Thu, 6 Sep 2018 13:27:27 +0000 (18:57 +0530)]
ath10k: fix tx status flag setting for management frames
The tx_status for management frames is being filled
incorrectly in the flags of skb_cb. This incorrect
flag setting causes the upper layers to consider that
the particular frame was not transmitted properly,
leading to improper behavior.
Set the IEEE80211_TX_STAT_ACK flag in the info flags
of skb_cb, to indicate the successful transmission of
the management frame.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes:
dc405152bb64d4ae01c9ac669de25b2d1fb6fc2d
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ben Greear [Thu, 6 Sep 2018 16:46:20 +0000 (19:46 +0300)]
ath10k: fix vdev-start timeout on error
The vdev-start-response message should cause the
completion to fire, even in the error case. Otherwise,
the user still gets no useful information and everything
is blocked until the timeout period.
Add some warning text to print out the invalid status
code to aid debugging, and propagate failure code.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Stromdahl [Tue, 4 Sep 2018 12:07:07 +0000 (15:07 +0300)]
ath10k: wmi: disable softirq's while calling ieee80211_rx
This is done in order not to trig the below warning in
ieee80211_rx_napi:
WARN_ON_ONCE(softirq_count() == 0);
ieee80211_rx_napi requires that softirq's are disabled during
execution.
The High latency bus drivers (SDIO and USB) sometimes call the wmi
ep_rx_complete callback from non softirq context, resulting in a trigger
of the above warning.
Calling ieee80211_rx_ni with softirq's already disabled (e.g., from
softirq context) should be safe as the local_bh_disable and
local_bh_enable functions (called from ieee80211_rx_ni) are fully
reentrant.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Stromdahl [Tue, 4 Sep 2018 12:06:58 +0000 (15:06 +0300)]
ath10k: htt: High latency RX support
Special HTT RX handling for high latency interfaces.
Since no DMA physical addresses are used in the RX ring
config message (this is not supported by the high latency
devices), no RX ring is allocated.
All RX skb's are allocated by the driver and passed directly
to mac80211 in the HTT RX indication handler.
A nice side effect of this is that no huge buffer will be
allocated with dma_alloc_coherent. On embedded systems with
limited memory resources, the allocation of the RX ring is
prone to fail.
Some tweaks made to "make it work":
Removal of protected bit in 802.11 header frame control field.
The chipset seems to do hw decryption but the frame_control
protected bit is still set.
This is necessary for mac80211 not to drop the frame.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Stromdahl [Tue, 4 Sep 2018 12:06:38 +0000 (15:06 +0300)]
ath10k: htt: High latency TX support
Add HTT TX function for HL interfaces.
Intended for SDIO and USB.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Stromdahl [Tue, 4 Sep 2018 12:06:13 +0000 (15:06 +0300)]
ath10k: htt: RX ring config HL support
Special HTT RX ring config message used by high latency
devices.
The main difference between HL and LL is that HL devices
do not use shared memory between device and host and thus,
no host paddr's are added to the RX config message.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Stromdahl [Tue, 4 Sep 2018 12:05:57 +0000 (15:05 +0300)]
ath10k: add HTT RX HL ops
Initial (empty) HTT RX ops for high latency devices.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Stromdahl [Tue, 4 Sep 2018 12:05:43 +0000 (15:05 +0300)]
ath10k: add HTT TX HL ops
Initial HTT TX ops for high latency devices.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Stromdahl [Tue, 4 Sep 2018 12:05:23 +0000 (15:05 +0300)]
ath10k: DMA related fixes for high latency devices
Several DMA related functions (such as the dma_map_xxx functions)
are not used with high latency devices and don't need to be invoked
in this case.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Stromdahl [Tue, 4 Sep 2018 12:05:04 +0000 (15:05 +0300)]
ath10k: add per target config of max_num_peers
This patch makes sure the value of max_num_peers matches
num_peers in hw_params (if set to a non zero value).
hw_params->num_peers is used in the TLV WMI init command.
If ar->max_num_peers is not set to the same value, there is a risk
that the user creates more peers than the maximum number of peers
supported by the device.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Stromdahl [Tue, 4 Sep 2018 12:04:26 +0000 (15:04 +0300)]
ath10k: use hw_params.num_peers for num_tids in TLV init
As TARGET_TLV_NUM_TIDS is calculated like this:
#define TARGET_TLV_NUM_TIDS ((TARGET_TLV_NUM_PEERS) * 2)
... it is better to use the per device hw_params.num_peers value in
the TLV init message (if set), rather than using a hard coded value.
This makes the value used in the TLV init message match the hw_param
value.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Stromdahl [Tue, 4 Sep 2018 12:04:07 +0000 (15:04 +0300)]
ath10k: add bus type check in ath10k_init_hw_params
The bus type is used together with the other hw parameters
to find a matching entry in ath10k_hw_params_list for the device.
This is necessary since HL devices can have the same dev_id and
target_version as a corresponding LL device (same chipset) and
yet use a totally different configuration.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Stromdahl [Tue, 4 Sep 2018 12:03:44 +0000 (15:03 +0300)]
ath10k: add device type enum to ath10k_bus_params
Add dev_type parameter to struct ath10k_bus_params.
The dev type specifies if the device is a high latency device (usb and
sdio) or low latency device (pci, ahb and snoc)
The setup of high latency chips is sometimes different than
for chips using low latency interfaces.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Stromdahl [Tue, 4 Sep 2018 12:03:19 +0000 (15:03 +0300)]
ath10k: add struct ath10k_bus_params
This struct is used as argument to ath10k_core_register in order to
make it easier to add more bus parameters in the future.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Carl Huang [Tue, 4 Sep 2018 10:00:51 +0000 (13:00 +0300)]
ath10k: download firmware via diag Copy Engine for QCA6174 and QCA9377.
Downloading firmware via BMI protocol takes too long time. For example,
a ~700K bytes firmware takes about 500ms to download via BMI protocol.
This is too long especially in suspend and resume scenario where firmware
is re-downloaded unless WoWLAN is enabled. Downloading firmware via diag CE
can reduce the time to ~40ms for a ~700K bytes firmware binary.
Ath10k driver parses the firmware to segments and downloads the segments
to the specified address directly. If the firmware is compressed or has
unsupported segments, ath10k driver will try BMI download again.
It's tested with QCA6174 hw3.2 and
firmware-6.bin_WLAN.RM.4.4.1-00111-QCARMSWP-1. QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Carl Huang [Tue, 4 Sep 2018 10:00:39 +0000 (13:00 +0300)]
ath10k: support to access target space below 1M for qca6174 and qca9377
To download firmware via diag interface, driver needs to write the target
memory space below 1M. It means the bit20 should be zero for the converted
address if the target memory space is below 1M. Otherwise, bit20 is one if
the target address is larger or equal to 1M space.
As downloading firmware via diag interface is only required for qca6174
and qca9377, a new specific function is introduced to convert the target
address to ce address: ath10k_pci_qca6174_targ_cpu_to_ce_addri().
This function supports to convert any target address to ce address.
It's tested with QCA6174 hw3.2 and
firmware-6.bin_WLAN.RM.4.4.1-00111-QCARMSWP-1. QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Carl Huang [Tue, 4 Sep 2018 10:00:25 +0000 (13:00 +0300)]
ath10k: optimize pci diag mem read & write operations
Delay 1ms is too long for both diag read and write operations.
This is observed when writing a big memory buffer to target or
reading a big memory buffer from target. Take writing/reading
512k bytes as example, the delay itself is 256ms as the maximum
length of every write/read is 2k size.
Reduce the delay to 50us for read and write operations.
Take the ath10k_pci_targ_cpu_to_ce_addr() out of loop and put it
in the beginning of the loop for ath10k_pci_diag_read_mem().
The ath10k_pci_targ_cpu_to_ce_addr() is to convert the address
from target cpu's perspective to CE's perspective, so it makes
no sense to convert a CE's perspective address again in the loop.
It's a wrong implementation but happens to work.
If the target address is below 1M space, then the convert in the loop
from the second time becomes wrong because the previously converted address
is larger than 1M. The counterpart ath10k_pci_diag_write_mem() has the
correct implementation.
With this change, ath10k_pci_diage_read_mem() works correctly no matter
the target address is below 1M or above 1M.
It's tested with QCA6174 hw3.2 and
firmware-6.bin_WLAN.RM.4.4.1-00111-QCARMSWP-1. QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Balaji Pothunoori [Tue, 4 Sep 2018 09:52:18 +0000 (12:52 +0300)]
ath10k: average ack rssi support for data frames
Average ack rssi value is weighted average of ack rssi for
no of msdu's has been sent.
This feature is enabled by the host driver if firmware is capable.
After receiving event from host, firmware allocates the necessary
memory to store the ack_rssi for data packets during the init time.
After each successful transmission, If tx completion status is OK
and 24th bit is set in HTT message header then host will fetch the
ack_rssi else host can ignore the ack_rssi field.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
K.T.VIJAYAKUMAAR [Mon, 3 Sep 2018 17:07:44 +0000 (20:07 +0300)]
ath10k: avoid possible memory access violation
array "ctl_power_table" access index "pream" is initialized with -1 and
is raised as a static analysis tool issue.
[drivers\net\wireless\ath\ath10k\wmi.c:4719] ->
[drivers\net\wireless\ath\ath10k\wmi.c:4730]: (error) Array index -1 is
out of bounds.
Since the "pream" index for accessing ctl_power_table array is initialized
with -1, there is a chance of memory access violation for the cases below.
1) wmi_pdev_tpc_final_table_event change frequency is between 2483 and 5180
2) pream_idx is out of the enumeration ranges of wmi_tpc_pream_2ghz,
wmi_tpc_pream_5ghz
Signed-off-by: K.T.VIJAYAKUMAAR <vijay.bvb@samsung.com>
[kvalo@codeaurora.org: clean up the warning message]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Anilkumar Kolli [Tue, 4 Sep 2018 06:45:16 +0000 (12:15 +0530)]
ath10k: add debugfs support to dump per sta tx stats
This patch adds 'tx_stats' in per station debugfs entry.
Use this command to dump tx_stats:
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/
stations/<MACADDR>/tx_stats
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Anilkumar Kolli [Tue, 4 Sep 2018 06:45:15 +0000 (12:15 +0530)]
ath10k: add extended per sta tx statistics support
This patch adds per station tx statistics support.
Per station tx stats include
- pkts/bytes transmitted at all possible rates(mcs/nss/bw/gi).
- ACK fails count
- ampdu bytes/pkts transmitted at all possible rates(mcs/nss/bw/gi).
- BA fails count
Tested on QCA9984/QCA4019/QCA988x
Firmware: 10.4-3.5.3-00057
10.2.4-1.0-00037
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Anilkumar Kolli [Tue, 4 Sep 2018 06:45:14 +0000 (12:15 +0530)]
ath10k: add debugfs entry to enable extended tx stats
This patch adds debugfs entry to enable/disable extended
tx statistics. Extended tx statistics are from peer stats
feature.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Anilkumar Kolli [Tue, 4 Sep 2018 06:45:13 +0000 (12:15 +0530)]
ath10k: get the legacy rate index to update the txrate table
Get the legacy rate index to update the pkts/bytes counter
against each possible tx rate.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Gustavo A. R. Silva [Wed, 29 Aug 2018 17:50:18 +0000 (12:50 -0500)]
wil6210: fix unsigned cid comparison with >= 0
The comparison of cid >= 0 is always true because cid is of type u8
(8 bits, unsigned).
Fix this by removing such comparison and updating the type of
variable cid to u8 in the caller function.
Addresses-Coverity-ID:
1473079 ("Unsigned compared against 0")
Fixes:
b9010f105f21 ("wil6210: add FT roam support for AP and station")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Mon, 3 Sep 2018 17:08:01 +0000 (20:08 +0300)]
ath10k: enable pktlog for WCN3990 target
WCN3990 target uses separate htc service for pktlog.
Add pktlog service request and support for pktlog
rx path handling.
Testing:
Tested on WCN3990 and QCA6174 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1,
WLAN.RM.4.4.1-00109-QCARMSWPZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Mon, 3 Sep 2018 17:07:58 +0000 (20:07 +0300)]
ath10k: introduce CE_ATTR_POLL attribute for polling pipe
Existing copy engine interrupt enable logic assumes that last
CE is using polling mode and due to this interrupt for last copy engine
are always disabled. WCN3990 uses last CE for pktlog and
interrupt remains disabled with existing logic.
To mitigate this issue, introduce CE_ATTR_POLL flag and control
the interrupt based on the flag which can be set in ce_attr.
Testing:
Tested on WCN3990 and QCA6174 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1,
WLAN.RM.4.4.1-00109-QCARMSWPZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sathishkumar Muruganandam [Mon, 3 Sep 2018 17:07:53 +0000 (20:07 +0300)]
ath10k: support extended board data download for dual-band QCA9984
To support dual-band variant of QCA9984, new extended board data (eBDF)
is introduced since existing board data ran out of space.
Below is the brief implementation & design detail,
----------------------------------------------------
1. New OTP changes to inform eBDF support in existing OTP download to
fetch board ID and chip ID. This is backward compatible and older
card sends 0 by default for eBDF support bit (bit 18 of OTP response) we
check in ath10k driver.
2. If eBDF is supported, then we need to fetch eBDF ID which is bundled
in downloaded board data. So again OTP is executed for knowing the eBDF ID.
This is done once we set 'board_data_initialized' bit. If eBDF ID
returned is zero, we continue booting with previous board data downloaded.
3. Based on the eBDF ID fetched, ath10k driver tries to download the
extended board data to a new offset ahead of already downloaded board
data address.
4. A new BD IE type, ATH10K_BD_IE_BOARD_EXT is added to differentiate in
bundling eBDF separately in board-2.bin and also to parse through
board bundle for eBDF download in ath10k boot.
5. If eBDF is not present in the board-2.bin bundle or when board ID is
zero, we do a fallback boot to "eboard.bin" in the same QCA9984/hw1.0 dir.
This is same as done to existing "board.bin" if board ID is not present
in board-2.bin bundle.
Current design is that eBDF size will be 2KB and eBDF ID will be
byte value.
Tested the above changes with dual-band variant of QCA9984 card. OTP
update needed for the test will be part of next FW release 10.4-3.6-xxxx.
Below are the logs with ath10k BOOT debugs enabled.
First OTP response :
---------------------
..
boot upload otp to 0x1234 len 9478 for board id
boot get otp board id result 0x00040400 board_id 1 chip_id 0 ext_bid_support 1
..
Second OTP response :
---------------------
..
boot upload otp to 0x1234 len 9478 for ext board id
boot get otp ext board id result 0x00000005 ext_board_id 5
boot using eboard name 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5'
..
Extended board data download:
------------------------------
..
board name
00000000: 62 75 73 3d 70 63 69 2c 62 6d 69 2d 63 68 69 70 bus=pci,bmi-chip
00000010: 2d 69 64 3d 30 2c 62 6d 69 2d 65 62 6f 61 72 64 -id=0,bmi-eboard
00000020: 2d 69 64 3d 35 -id=5
boot found match for name 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5'
boot found eboard data for 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5'
using board api 2
boot writing ext board data to addr 0xc3000
..
Fallback Extended board data download from "eboard.bin":
---------------------------------------------------------
..
board name
00000000: 62 75 73 3d 70 63 69 2c 62 6d 69 2d 63 68 69 70 bus=pci,bmi-chip
00000010: 2d 69 64 3d 30 2c 62 6d 69 2d 62 6f 61 72 64 2d -id=0,bmi-board-
00000020: 69 64 3d 31 30 id=10
failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-eboard-id=5 from ath10k/QCA9984/hw1.0/board-2.bin
boot fw request 'ath10k/QCA9984/hw1.0/eboard.bin': 0
using board api 1
boot writing ext board data to addr 0xc3000
..
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sathishkumar Muruganandam [Mon, 3 Sep 2018 17:07:50 +0000 (20:07 +0300)]
ath10k: refactoring needed for extended board data download
Just moving functions down in the file, no functional changes.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Niklas Cassel [Tue, 12 Jun 2018 11:39:06 +0000 (13:39 +0200)]
ath10k: allow ATH10K_SNOC with COMPILE_TEST
ATH10K_SNOC builds just fine with COMPILE_TEST, so make that possible.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rob Herring [Tue, 28 Aug 2018 16:48:46 +0000 (19:48 +0300)]
ath6kl: convert to using %pOFn instead of device_node.name
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wen Gong [Tue, 28 Aug 2018 16:48:42 +0000 (19:48 +0300)]
ath10k: add waiting htt tx complete before wow enable
If there are some tx packets pending in firmware, and then system
enters suspend, firmware will fail for wow enable. This will trigger
mac80211 to stop ath10k and download firmware again, then it is
non-wow suspend.
After add the waiting htt tx complete, then firmware will have some
time window to send or flush the pending tx packets.
Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1, but this will also affect QCA9377 PCI.
It's not a regression with new firmware releases.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Tue, 28 Aug 2018 16:48:17 +0000 (19:48 +0300)]
ath10k: retrieve MAC address from system firmware if provided
Devices may provide their own MAC address via system firmware (e.g.,
device tree), especially in the case where the device doesn't have a
useful EEPROM on which to store its MAC address (e.g., for integrated
Wifi).
Use the generic device helper to retrieve the MAC address, and (if
present) honor it above the MAC address advertised by the card.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Tue, 28 Aug 2018 16:39:22 +0000 (19:39 +0300)]
Merge ath-next from git://git./linux/kernel/git/kvalo/ath.git
ath.git patches for 4.20. Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
Sven Eckelmann [Fri, 24 Aug 2018 12:04:59 +0000 (15:04 +0300)]
ath10k: limit available channels via DT ieee80211-freq-limit
Tri-band devices (1x 2.4GHz + 2x 5GHz) often incorporate special filters in
the RX and TX path. These filtered channel can in theory still be used by
the hardware but the signal strength is reduced so much that it makes no
sense.
There is already a DT property to limit the available channels but ath10k
has to manually call this functionality to limit the currrently set wiphy
channels further.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dedy Lansky [Thu, 23 Aug 2018 11:47:13 +0000 (14:47 +0300)]
wil6210: fix invalid memory access for rx_buff_mgmt debugfs
Check rx_buff_mgmt is allocated before accessing its internal fields.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ahmad Masri [Thu, 23 Aug 2018 11:47:12 +0000 (14:47 +0300)]
wil6210: add FT roam support for AP and station
This feature is needed for enterprise APs and clients to enable
fast roaming as defined in 802.11r between APs in the same ESS.
On AP side, this feature is supported only when disable_ap_sme
is enabled.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Maya Erez [Thu, 23 Aug 2018 11:47:11 +0000 (14:47 +0300)]
wil6210: fix RX buffers release and unmap
RX SKBs are released in both wil6210 rmmod and RX handle.
As there is no lock to protect the buffers DMA unmap,
the SKB pointer in buff_arr is used to check if the buffer
memory was already released.
Setting wil->rx_buff_mgmt.buff_arr[buff_id].skb to NULL before the DMA
memory unmap will prevent duplicate unmapping of the same memory.
Move the buffer ID to the free list also in case the SKB is NULL.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Maya Erez [Thu, 23 Aug 2018 11:47:10 +0000 (14:47 +0300)]
wil6210: prevent usage of tx ring 0 for eDMA
In enhanced DMA ring 0 is used for RX ring, hence TX ring 0
is an unused element in ring_tx and ring2cid_tid arrays.
Initialize ring2cid_tid CID to WIL6210_MAX_CID to prevent a false
match of CID 0.
Go over the ring_tx and ring2cid_tid from wil_get_min_tx_ring_id
and on to prevent access to index 0 in eDMA.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Maya Erez [Thu, 23 Aug 2018 11:47:09 +0000 (14:47 +0300)]
wil6210: allocate rx reorder buffer only if rx reorder is enabled
wil_addba_rx_request allocates the rx reorder buffer regardless
of use_rx_hw_reordering settings.
Fix this by checking wil->use_rx_hw_reordering before allocating
the reorder buffer.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Maya Erez [Thu, 23 Aug 2018 11:47:08 +0000 (14:47 +0300)]
wil6210: set edma variables only for Talyn-MB devices
use_rx_hw_reordering is already set to true in wil_set_capabilities
for Talyn-MB devices. Remove its setting from wil_priv_init to
prevent its activation for older chips.
Similarly, move the setting of use_compressed_rx_status to
wil_set_capabilities.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dedy Lansky [Thu, 23 Aug 2018 11:47:07 +0000 (14:47 +0300)]
wil6210: drop Rx multicast packets that are looped-back to STA
Delivering a looped-back multicast packet to network stack can cause
higher layer protocols to fail like for example IPv6 DAD.
In STA mode, upon receiving Rx multicast packet, check if the source
MAC address is equal to our own MAC address and if so drop the packet.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Alexei Avshalom Lazar [Thu, 23 Aug 2018 11:47:06 +0000 (14:47 +0300)]
wil6210: add support for channel 4
wil6210 supports channels 1-3 of the 60GHz band.
New FW added support for channel 4. Add support for channel 4 also in
wil6210 driver.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Karthick Gopalasubramanian [Thu, 23 Aug 2018 11:47:05 +0000 (14:47 +0300)]
wil6210: remove reset file from debugfs
Reset file is not used and may cause race conditions
with operational driver if used.
Signed-off-by: Karthick Gopalasubramanian <kargop@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Varsha Rao [Wed, 25 Jul 2018 18:49:48 +0000 (20:49 +0200)]
ath6kl: Remove unnecessary parentheses
Remove extra parentheses to fix the clang warning of extraneous
parentheses.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Felix Fietkau [Mon, 20 Aug 2018 09:37:51 +0000 (11:37 +0200)]
ath9k: fix tx99 with monitor mode interface
Tx99 is typically configured via a monitor mode interface, which does
not get added to the driver as a vif. Since the code currently expects
a configured virtual interface for tx99, enabling tx99 via debugfs fails.
Since the vif is not needed anyway, remove all checks for it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@codeaurora.org: s/CPTCFG/CONFIG/]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Colin Ian King [Thu, 16 Aug 2018 12:50:30 +0000 (13:50 +0100)]
ath9k: remove unused array firstep_table
Array firstep_table is being assigned but is never used
hence it is redundant and can be removed.
Cleans up clang warning:
warning: 'firstep_table' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Varsha Rao [Wed, 25 Jul 2018 18:53:03 +0000 (20:53 +0200)]
ath9k: Remove unnecessary parentheses
Remove extra parentheses to fix the clang warning of extraneous
parentheses.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Gustavo A. R. Silva [Fri, 24 Aug 2018 01:12:47 +0000 (20:12 -0500)]
ath10k: use struct_size() in kzalloc()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Martin Willi [Wed, 22 Aug 2018 07:39:52 +0000 (09:39 +0200)]
ath10k: schedule hardware restart if WMI command times out
When running in AP mode, ath10k sometimes suffers from TX credit
starvation. The issue is hard to reproduce and shows up once in a
few days, but has been repeatedly seen with QCA9882 and a large
range of firmwares, including 10.2.4.70.67.
Once the module is in this state, TX credits are never replenished,
which results in "SWBA overrun" errors, as no beacons can be sent.
Even worse, WMI commands run in a timeout while holding the conf
mutex for three seconds each, making any further operations slow
and the whole system unresponsive.
The firmware/driver never recovers from that state automatically,
and triggering TX flush or warm restarts won't work over WMI. So
issue a hardware restart if a WMI command times out due to missing
TX credits. This implies a connectivity outage of about 1.4s in AP
mode, but brings back the interface and the whole system to a usable
state. WMI command timeouts have not been seen in absent of this
specific issue, so taking such drastic actions seems legitimate.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rakesh Pillai [Mon, 6 Aug 2018 14:48:08 +0000 (20:18 +0530)]
ath10k: skip resetting rx filter for WCN3990
WCN3990 has the MAC_PCU_ADDR1 configured properly
and hence it will not send spurious ack frames
during boot up.
Hence the reset_rx_filter workaround is not needed
for WCN3990. Add a hw_param to indicate if hardware rx
filter reset is needed and skip the reset_rx_filter for
WCN3990.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Linus Torvalds [Mon, 27 Aug 2018 18:59:39 +0000 (11:59 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) ICE, E1000, IGB, IXGBE, and I40E bug fixes from the Intel folks.
2) Better fix for AB-BA deadlock in packet scheduler code, from Cong
Wang.
3) bpf sockmap fixes (zero sized key handling, etc.) from Daniel
Borkmann.
4) Send zero IPID in TCP resets and SYN-RECV state ACKs, to prevent
attackers using it as a side-channel. From Eric Dumazet.
5) Memory leak in mediatek bluetooth driver, from Gustavo A. R. Silva.
6) Hook up rt->dst.input of ipv6 anycast routes properly, from Hangbin
Liu.
7) hns and hns3 bug fixes from Huazhong Tan.
8) Fix RIF leak in mlxsw driver, from Ido Schimmel.
9) iova range check fix in vhost, from Jason Wang.
10) Fix hang in do_tcp_sendpages() with tls, from John Fastabend.
11) More r8152 chips need to disable RX aggregation, from Kai-Heng Feng.
12) Memory exposure in TCA_U32_SEL handling, from Kees Cook.
13) TCP BBR congestion control fixes from Kevin Yang.
14) hv_netvsc, ignore non-PCI devices, from Stephen Hemminger.
15) qed driver fixes from Tomer Tayar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
net: sched: Fix memory exposure from short TCA_U32_SEL
qed: fix spelling mistake "comparsion" -> "comparison"
vhost: correctly check the iova range when waking virtqueue
qlge: Fix netdev features configuration.
net: macb: do not disable MDIO bus at open/close time
Revert "net: stmmac: fix build failure due to missing COMMON_CLK dependency"
net: macb: Fix regression breaking non-MDIO fixed-link PHYs
mlxsw: spectrum_switchdev: Do not leak RIFs when removing bridge
i40e: fix condition of WARN_ONCE for stat strings
i40e: Fix for Tx timeouts when interface is brought up if DCB is enabled
ixgbe: fix driver behaviour after issuing VFLR
ixgbe: Prevent unsupported configurations with XDP
ixgbe: Replace GFP_ATOMIC with GFP_KERNEL
igb: Replace mdelay() with msleep() in igb_integrated_phy_loopback()
igb: Replace GFP_ATOMIC with GFP_KERNEL in igb_sw_init()
igb: Use an advanced ctx descriptor for launchtime
e1000: ensure to free old tx/rx rings in set_ringparam()
e1000: check on netif_running() before calling e1000_up()
ixgb: use dma_zalloc_coherent instead of allocator/memset
ice: Trivial formatting fixes
...
Jens Axboe [Mon, 27 Aug 2018 14:37:46 +0000 (08:37 -0600)]
Fix up libata MAINTAINERS entry
The email was botched in one entry, and I also forgot to update the
location of the git tree. It'll be under the linux-block umbrella, just
with different branches.
Reported-by: Baruch Siach <baruch@tkos.co.il>
Fixes:
7634ccd2da97 ("libata: maintainership update")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kees Cook [Sun, 26 Aug 2018 05:58:01 +0000 (22:58 -0700)]
net: sched: Fix memory exposure from short TCA_U32_SEL
Via u32_change(), TCA_U32_SEL has an unspecified type in the netlink
policy, so max length isn't enforced, only minimum. This means nkeys
(from userspace) was being trusted without checking the actual size of
nla_len(), which could lead to a memory over-read, and ultimately an
exposure via a call to u32_dump(). Reachability is CAP_NET_ADMIN within
a namespace.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 26 Aug 2018 21:11:59 +0000 (14:11 -0700)]
Linux 4.19-rc1
Linus Torvalds [Sun, 26 Aug 2018 20:39:05 +0000 (13:39 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer update from Thomas Gleixner:
"New defines for the compat time* types so they can be shared between
32bit and 64bit builds. Not used yet, but merging them now allows the
actual conversions to be merged through different maintainer trees
without dependencies
We still have compat interfaces for 32bit on 64bit even with the new
2038 safe timespec/val variants because pointer size is different. And
for the old style timespec/val interfaces we need yet another 'compat'
interface for both 32bit native and 32bit on 64bit"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
y2038: Provide aliases for compat helpers
Linus Torvalds [Sun, 26 Aug 2018 18:48:42 +0000 (11:48 -0700)]
Merge branch 'ida-4.19' of git://git.infradead.org/users/willy/linux-dax
Pull IDA updates from Matthew Wilcox:
"A better IDA API:
id = ida_alloc(ida, GFP_xxx);
ida_free(ida, id);
rather than the cumbersome ida_simple_get(), ida_simple_remove().
The new IDA API is similar to ida_simple_get() but better named. The
internal restructuring of the IDA code removes the bitmap
preallocation nonsense.
I hope the net -200 lines of code is convincing"
* 'ida-4.19' of git://git.infradead.org/users/willy/linux-dax: (29 commits)
ida: Change ida_get_new_above to return the id
ida: Remove old API
test_ida: check_ida_destroy and check_ida_alloc
test_ida: Convert check_ida_conv to new API
test_ida: Move ida_check_max
test_ida: Move ida_check_leaf
idr-test: Convert ida_check_nomem to new API
ida: Start new test_ida module
target/iscsi: Allocate session IDs from an IDA
iscsi target: fix session creation failure handling
drm/vmwgfx: Convert to new IDA API
dmaengine: Convert to new IDA API
ppc: Convert vas ID allocation to new IDA API
media: Convert entity ID allocation to new IDA API
ppc: Convert mmu context allocation to new IDA API
Convert net_namespace to new IDA API
cb710: Convert to new IDA API
rsxx: Convert to new IDA API
osd: Convert to new IDA API
sd: Convert to new IDA API
...
Linus Torvalds [Sun, 26 Aug 2018 18:41:08 +0000 (11:41 -0700)]
Merge tag 'gcc-plugins-v4.19-rc1-fix' of git://git./linux/kernel/git/kees/linux
Pull gcc plugin fix from Kees Cook:
"Lift gcc test into Kconfig. This is for better behavior when the
kernel is built with Clang, reported by Stefan Agner"
* tag 'gcc-plugins-v4.19-rc1-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-plugins: Disable when building under Clang
Linus Torvalds [Sun, 26 Aug 2018 18:25:21 +0000 (11:25 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf updates from Thomas Gleixner:
"Kernel:
- Improve kallsyms coverage
- Add x86 entry trampolines to kcore
- Fix ARM SPE handling
- Correct PPC event post processing
Tools:
- Make the build system more robust
- Small fixes and enhancements all over the place
- Update kernel ABI header copies
- Preparatory work for converting libtraceevnt to a shared library
- License cleanups"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (100 commits)
tools arch: Update arch/x86/lib/memcpy_64.S copy used in 'perf bench mem memcpy'
tools arch x86: Update tools's copy of cpufeatures.h
perf python: Fix pyrf_evlist__read_on_cpu() interface
perf mmap: Store real cpu number in 'struct perf_mmap'
perf tools: Remove ext from struct kmod_path
perf tools: Add gzip_is_compressed function
perf tools: Add lzma_is_compressed function
perf tools: Add is_compressed callback to compressions array
perf tools: Move the temp file processing into decompress_kmodule
perf tools: Use compression id in decompress_kmodule()
perf tools: Store compression id into struct dso
perf tools: Add compression id into 'struct kmod_path'
perf tools: Make is_supported_compression() static
perf tools: Make decompress_to_file() function static
perf tools: Get rid of dso__needs_decompress() call in __open_dso()
perf tools: Get rid of dso__needs_decompress() call in symbol__disassemble()
perf tools: Get rid of dso__needs_decompress() call in read_object_code()
tools lib traceevent: Change to SPDX License format
perf llvm: Allow passing options to llc in addition to clang
perf parser: Improve error message for PMU address filters
...
Linus Torvalds [Sun, 26 Aug 2018 17:13:21 +0000 (10:13 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
- Correct the L1TF fallout on 32bit and the off by one in the 'too much
RAM for protection' calculation.
- Add a helpful kernel message for the 'too much RAM' case
- Unbreak the VDSO in case that the compiler desides to use indirect
jumps/calls and emits retpolines which cannot be resolved because the
kernel uses its own thunks, which does not work for the VDSO. Make it
use the builtin thunks.
- Re-export start_thread() which was unexported when the 32/64bit
implementation was unified. start_thread() is required by modular
binfmt handlers.
- Trivial cleanups
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/speculation/l1tf: Suggest what to do on systems with too much RAM
x86/speculation/l1tf: Fix off-by-one error when warning that system has too much RAM
x86/kvm/vmx: Remove duplicate l1d flush definitions
x86/speculation/l1tf: Fix overflow in l1tf_pfn_limit() on 32bit
x86/process: Re-export start_thread()
x86/mce: Add notifier_block forward declaration
x86/vdso: Fix vDSO build if a retpoline is emitted
Linus Torvalds [Sun, 26 Aug 2018 16:55:28 +0000 (09:55 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq update from Thomas Gleixner:
"A small set of updats/fixes for the irq subsystem:
- Allow GICv3 interrupts to be configured as wake-up sources to
enable wakeup from suspend
- Make the error handling of the STM32 irqchip init function work
- A set of small cleanups and improvements"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Allow interrupt to be configured as wake-up sources
irqchip/tango: Set irq handler and data in one go
dt-bindings: irqchip: renesas-irqc: Document r8a774a1 support
irqchip/s3c24xx: Remove unneeded comparison of unsigned long to 0
irqchip/stm32: Fix init error handling
irqchip/bcm7038-l1: Hide cpu offline callback when building for !SMP
Linus Torvalds [Sun, 26 Aug 2018 16:47:00 +0000 (09:47 -0700)]
Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull licking update from Thomas Gleixner:
"Mark the switch cases which fall through to the next case with the
proper comment so the fallthrough compiler checks can be enabled"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Mark expected switch fall-throughs
Linus Torvalds [Sun, 26 Aug 2018 01:43:59 +0000 (18:43 -0700)]
Merge tag 'libnvdimm-for-4.19_dax-memory-failure' of gitolite.pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm memory-failure update from Dave Jiang:
"As it stands, memory_failure() gets thoroughly confused by dev_pagemap
backed mappings. The recovery code has specific enabling for several
possible page states and needs new enabling to handle poison in dax
mappings.
In order to support reliable reverse mapping of user space addresses:
1/ Add new locking in the memory_failure() rmap path to prevent races
that would typically be handled by the page lock.
2/ Since dev_pagemap pages are hidden from the page allocator and the
"compound page" accounting machinery, add a mechanism to determine
the size of the mapping that encompasses a given poisoned pfn.
3/ Given pmem errors can be repaired, change the speculatively
accessed poison protection, mce_unmap_kpfn(), to be reversible and
otherwise allow ongoing access from the kernel.
A side effect of this enabling is that MADV_HWPOISON becomes usable
for dax mappings, however the primary motivation is to allow the
system to survive userspace consumption of hardware-poison via dax.
Specifically the current behavior is:
mce: Uncorrected hardware memory error in user-access at
af34214200
{1}[Hardware Error]: It has been corrected by h/w and requires no further action
mce: [Hardware Error]: Machine check events logged
{1}[Hardware Error]: event severity: corrected
Memory failure: 0xaf34214: reserved kernel page still referenced by 1 users
[..]
Memory failure: 0xaf34214: recovery action for reserved kernel page: Failed
mce: Memory error not recovered
<reboot>
...and with these changes:
Injecting memory failure for pfn 0x20cb00 at process virtual address 0x7f763dd00000
Memory failure: 0x20cb00: Killing dax-pmd:5421 due to hardware memory corruption
Memory failure: 0x20cb00: recovery action for dax page: Recovered
Given all the cross dependencies I propose taking this through
nvdimm.git with acks from Naoya, x86/core, x86/RAS, and of course dax
folks"
* tag 'libnvdimm-for-4.19_dax-memory-failure' of gitolite.kernel.org:pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, pmem: Restore page attributes when clearing errors
x86/memory_failure: Introduce {set, clear}_mce_nospec()
x86/mm/pat: Prepare {reserve, free}_memtype() for "decoy" addresses
mm, memory_failure: Teach memory_failure() about dev_pagemap pages
filesystem-dax: Introduce dax_lock_mapping_entry()
mm, memory_failure: Collect mapping size in collect_procs()
mm, madvise_inject_error: Let memory_failure() optionally take a page reference
mm, dev_pagemap: Do not clear ->mapping on final put
mm, madvise_inject_error: Disable MADV_SOFT_OFFLINE for ZONE_DEVICE pages
filesystem-dax: Set page->index
device-dax: Set page->index
device-dax: Enable page_mapping()
device-dax: Convert to vmf_insert_mixed and vm_fault_t
Linus Torvalds [Sun, 26 Aug 2018 01:13:10 +0000 (18:13 -0700)]
Merge tag 'libnvdimm-for-4.19_misc' of gitolite.pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dave Jiang:
"Collection of misc libnvdimm patches for 4.19 submission:
- Adding support to read locked nvdimm capacity.
- Change test code to make DSM failure code injection an override.
- Add support for calculate maximum contiguous area for namespace.
- Add support for queueing a short ARS when there is on going ARS for
nvdimm.
- Allow NULL to be passed in to ->direct_access() for kaddr and pfn
params.
- Improve smart injection support for nvdimm emulation testing.
- Fix test code that supports for emulating controller temperature.
- Fix hang on error before devm_memremap_pages()
- Fix a bug that causes user memory corruption when data returned to
user for ars_status.
- Maintainer updates for Ross Zwisler emails and adding Jan Kara to
fsdax"
* tag 'libnvdimm-for-4.19_misc' of gitolite.kernel.org:pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm: fix ars_status output length calculation
device-dax: avoid hang on error before devm_memremap_pages()
tools/testing/nvdimm: improve emulation of smart injection
filesystem-dax: Do not request kaddr and pfn when not required
md/dm-writecache: Don't request pointer dummy_addr when not required
dax/super: Do not request a pointer kaddr when not required
tools/testing/nvdimm: kaddr and pfn can be NULL to ->direct_access()
s390, dcssblk: kaddr and pfn can be NULL to ->direct_access()
libnvdimm, pmem: kaddr and pfn can be NULL to ->direct_access()
acpi/nfit: queue issuing of ars when an uc error notification comes in
libnvdimm: Export max available extent
libnvdimm: Use max contiguous area for namespace size
MAINTAINERS: Add Jan Kara for filesystem DAX
MAINTAINERS: update Ross Zwisler's email address
tools/testing/nvdimm: Fix support for emulating controller temperature
tools/testing/nvdimm: Make DSM failure code injection an override
acpi, nfit: Prefer _DSM over _LSR for namespace label reads
libnvdimm: Introduce locked DIMM capacity support
Colin Ian King [Fri, 24 Aug 2018 11:18:30 +0000 (12:18 +0100)]
qed: fix spelling mistake "comparsion" -> "comparison"
Trivial fix to spelling mistake in DP_ERR error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Fri, 24 Aug 2018 08:53:13 +0000 (16:53 +0800)]
vhost: correctly check the iova range when waking virtqueue
We don't wakeup the virtqueue if the first byte of pending iova range
is the last byte of the range we just got updated. This will lead a
virtqueue to wait for IOTLB updating forever. Fixing by correct the
check and wake up the virtqueue in this case.
Fixes:
6b1e6cc7855b ("vhost: new device IOTLB API")
Reported-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Peter Xu <peterx@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Thu, 23 Aug 2018 20:20:52 +0000 (13:20 -0700)]
qlge: Fix netdev features configuration.
qlge_fix_features() is not supposed to modify hardware or
driver state, rather it is supposed to only fix requested
fetures bits. Currently qlge_fix_features() also goes for
interface down and up unnecessarily if there is not even
any change in features set.
This patch changes/fixes following -
1) Move reload of interface or device re-config from
qlge_fix_features() to qlge_set_features().
2) Reload of interface in qlge_set_features() only if
relevant feature bit (NETIF_F_HW_VLAN_CTAG_RX) is changed.
3) Get rid of qlge_fix_features() since driver is not really
required to fix any features bit.
Signed-off-by: Manish <manish.chopra@cavium.com>
Reviewed-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anssi Hannula [Thu, 23 Aug 2018 07:45:22 +0000 (10:45 +0300)]
net: macb: do not disable MDIO bus at open/close time
macb_reset_hw() is called from macb_close() and indirectly from
macb_open(). macb_reset_hw() zeroes the NCR register, including the MPE
(Management Port Enable) bit.
This will prevent accessing any other PHYs for other Ethernet MACs on
the MDIO bus, which remains registered at macb_reset_hw() time, until
macb_init_hw() is called from macb_open() which sets the MPE bit again.
I.e. currently the MDIO bus has a short disruption at open time and is
disabled at close time until the interface is opened again.
Fix that by only touching the RE and TE bits when enabling and disabling
RX/TX.
v2: Make macb_init_hw() NCR write a single statement.
Fixes:
6c36a7074436 ("macb: Use generic PHY layer")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Wed, 22 Aug 2018 13:27:23 +0000 (15:27 +0200)]
Revert "net: stmmac: fix build failure due to missing COMMON_CLK dependency"
This reverts commit
bde4975310eb1982bd0bbff673989052d92fd481.
All legacy clock implementations now implement clk_set_rate() (Some
implementations may be dummies, though).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arnd.de>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ahmad Fatoum [Tue, 21 Aug 2018 15:35:48 +0000 (17:35 +0200)]
net: macb: Fix regression breaking non-MDIO fixed-link PHYs
commit
739de9a1563a ("net: macb: Reorganize macb_mii bringup") broke
initializing macb on the EVB-KSZ9477 eval board.
There, of_mdiobus_register was called even for the fixed-link representing
the RGMII-link to the switch with the result that the driver attempts to
enumerate PHYs on a non-existent MDIO bus:
libphy: MACB_mii_bus: probed
mdio_bus
f0028000.ethernet-
ffffffff: fixed-link has invalid PHY address
mdio_bus
f0028000.ethernet-
ffffffff: scan phy fixed-link at address 0
[snip]
mdio_bus
f0028000.ethernet-
ffffffff: scan phy fixed-link at address 31
The "MDIO" bus registration succeeds regardless, having claimed the reset GPIO,
and calling of_phy_register_fixed_link later on fails because it tries
to claim the same GPIO:
macb
f0028000.ethernet: broken fixed-link specification
Fix this by registering the fixed-link before calling mdiobus_register.
Fixes:
739de9a1563a ("net: macb: Reorganize macb_mii bringup")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 24 Aug 2018 12:41:35 +0000 (15:41 +0300)]
mlxsw: spectrum_switchdev: Do not leak RIFs when removing bridge
When a bridge device is removed, the VLANs are flushed from each
configured port. This causes the ports to decrement the reference count
on the associated FIDs (filtering identifier). If the reference count of
a FID is 1 and it has a RIF (router interface), then this RIF is
destroyed.
However, if no port is member in the VLAN for which a RIF exists, then
the RIF will continue to exist after the removal of the bridge. To
reproduce:
# ip link add name br0 type bridge vlan_filtering 1
# ip link set dev swp1 master br0
# ip link add link br0 name br0.10 type vlan id 10
# ip address add 192.0.2.0/24 dev br0.10
# ip link del dev br0
The RIF associated with br0.10 continues to exist.
Fix this by iterating over all the bridge device uppers when it is
destroyed and take care of destroying their RIFs.
Fixes:
99f44bb3527b ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 25 Aug 2018 21:12:36 +0000 (14:12 -0700)]
Merge tag 'armsoc-late' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC late updates from Olof Johansson:
"A couple of late-merged changes that would be useful to get in this
merge window:
- Driver support for reset of audio complex on Meson platforms. The
audio driver went in this merge window, and these changes have been
in -next for a while (just not in our tree).
- Power management fixes for IOMMU on Rockchip platforms, getting
closer to kexec working on them, including Chromebooks.
- Another pass updating "arm,psci" -> "psci" for some properties that
have snuck in since last time it was done"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
iommu/rockchip: Move irq request past pm_runtime_enable
iommu/rockchip: Handle errors returned from PM framework
arm64: rockchip: Force CONFIG_PM on Rockchip systems
ARM: rockchip: Force CONFIG_PM on Rockchip systems
arm64: dts: Fix various entry-method properties to reflect documentation
reset: imx7: Fix always writing bits as 0
reset: meson: add meson audio arb driver
reset: meson: add dt-bindings for meson-axg audio arb
Linus Torvalds [Sat, 25 Aug 2018 20:40:38 +0000 (13:40 -0700)]
Merge tag 'kbuild-v4.19-2' of git://git./linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- add build_{menu,n,g,x}config targets for compile-testing Kconfig
- fix and improve recursive dependency detection in Kconfig
- fix parallel building of menuconfig/nconfig
- fix syntax error in clang-version.sh
- suppress distracting log from syncconfig
- remove obsolete "rpm" target
- remove VMLINUX_SYMBOL(_STR) macro entirely
- fix microblaze build with CONFIG_DYNAMIC_FTRACE
- move compiler test for dead code/data elimination to Kconfig
- rename well-known LDFLAGS variable to KBUILD_LDFLAGS
- misc fixes and cleanups
* tag 'kbuild-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: rename LDFLAGS to KBUILD_LDFLAGS
kbuild: pass LDFLAGS to recordmcount.pl
kbuild: test dead code/data elimination support in Kconfig
initramfs: move gen_initramfs_list.sh from scripts/ to usr/
vmlinux.lds.h: remove stale <linux/export.h> include
export.h: remove VMLINUX_SYMBOL() and VMLINUX_SYMBOL_STR()
Coccinelle: remove pci_alloc_consistent semantic to detect in zalloc-simple.cocci
kbuild: make sorting initramfs contents independent of locale
kbuild: remove "rpm" target, which is alias of "rpm-pkg"
kbuild: Fix LOADLIBES rename in Documentation/kbuild/makefiles.txt
kconfig: suppress "configuration written to .config" for syncconfig
kconfig: fix "Can't open ..." in parallel build
kbuild: Add a space after `!` to prevent parsing as file pattern
scripts: modpost: check memory allocation results
kconfig: improve the recursive dependency report
kconfig: report recursive dependency involving 'imply'
kconfig: error out when seeing recursive dependency
kconfig: add build-only configurator targets
scripts/dtc: consolidate include path options in Makefile
Linus Torvalds [Sat, 25 Aug 2018 20:30:23 +0000 (13:30 -0700)]
Merge tag 'for-linus-
20180825' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A few small fixes for this merge window:
- Locking imbalance fix for bcache (Shan Hai)
- A few small fixes for wbt. One is a cleanup/prep, one is a fix for
an existing issue, and the last two are fixes for changes that went
into this merge window (me)"
* tag 'for-linus-
20180825' of git://git.kernel.dk/linux-block:
blk-wbt: don't maintain inflight counts if disabled
blk-wbt: fix has-sleeper queueing check
blk-wbt: use wq_has_sleeper() for wq active check
blk-wbt: move disable check into get_limit()
bcache: release dc->writeback_lock properly in bch_writeback_thread()
Linus Torvalds [Sat, 25 Aug 2018 20:27:35 +0000 (13:27 -0700)]
Merge tag 'upstream-4.19-rc1-fix' of git://git.infradead.org/linux-ubifs
Pull UBIFS fix from Richard Weinberger:
"Remove an empty file from UBIFS source"
* tag 'upstream-4.19-rc1-fix' of git://git.infradead.org/linux-ubifs:
ubifs: Remove empty file.h
Linus Torvalds [Sat, 25 Aug 2018 20:17:53 +0000 (13:17 -0700)]
Merge tag '4.19-rc-smb3' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Three small SMB3 fixes, one for stable"
* tag '4.19-rc-smb3' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module version number for cifs.ko to 2.12
cifs: check kmalloc before use
cifs: check if SMB2 PDU size has been padded and suppress the warning
cifs: create a define for how many iovs we need for an SMB2_open()
Linus Torvalds [Mon, 9 Jul 2018 20:19:49 +0000 (13:19 -0700)]
mm/cow: don't bother write protecting already write-protected pages
This is not normally noticeable, but repeated forks are unnecessarily
expensive because they repeatedly dirty the parent page tables during
the page table copy operation.
It's trivial to just avoid write protecting the page table entry if it
was already not writable.
This patch was inspired by
https://bugzilla.kernel.org/show_bug.cgi?id=200447
which points to an ancient "waste time re-doing fork" issue in the
presence of lots of signals.
That bug was fixed by Eric Biederman's signal handling series
culminating in commit
c3ad2c3b02e9 ("signal: Don't restart fork when
signals come in"), but the unnecessary work for repeated forks is still
work just fixing, particularly since the fix is trivial.
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Colin Ian King [Sat, 25 Aug 2018 10:24:31 +0000 (12:24 +0200)]
hpfs: remove unnecessary checks on the value of r when assigning error code
At the point where r is being checked for different values, r is always
going to be equal to 2 as the previous if statements jump to end or end1
if r is not 2. Hence the assignment to err can be simplified to just
err an assignment without any checks on the value or r.
Detected by CoverityScan, CID#
1226737 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jens Axboe [Sat, 25 Aug 2018 16:10:33 +0000 (10:10 -0600)]
libata: maintainership update
Tejun Heo wrote:
>
> I asked Jens whether he could take care of the libata tree and he
> thankfully agreed, so, from now on, Jens will be the libata
> maintainer.
>
> Thanks a lot!
Thanks for your work in this area. I still remember the first linux
storage summit we did in Vancouver 2001, Tejun was invited to talk about
his libata error handling work. Before that, it was basically a crap
shoot if we recovered properly or not... A lot of water has flown under
the bridge since then!
Here's an "official" patch. Linus, can you apply it?
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Sat, 25 Aug 2018 06:40:38 +0000 (23:40 -0700)]
Merge branch '1GbE' of git://git./linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-08-24
This series contains fixes to e1000, igb, ixgb, ixgbe and i40e.
YueHaibing from Huawei provides a change to use dma_zalloc_coherent()
instead of calls to allocator followed by a memset for ixgb.
Bo Chen provides a couple of fixes for e1000, first by adding a check to
prevent a NULL pointer dereference. The second change is to clean up a
possible resource leak on old transmit and receive rings when the device
is not up.
Jesus fixes an issue in the usage of an advanced transmit context
descriptor for retrieving the timestamp of a packet for AF_PACKET if the
IGB_TX_FLAGS_VLAN is not set in igb.
Jia-Ju Bai provides several patches which replace GFP_ATOMIC with
GFP_KERNEL, when using kzalloc() and kcalloc() which is not necessary.
Also found an instance of mdelay() call which could be replaced with
msleep().
Tony fixes ixgbe to allow MTU changes with XDP, by adding checks to
ensure only supported values and return -EINVAL for when it is not
supported.
Sebastian fixed an issue that was not clearing VF mailbox memory and
ensure queues are re-enabled correctly.
Martyna fixes a transmit timeout when DCB is configured when bringing up
an interface.
Jake fixes a previous commit which accidentally reversed the check of
the data pointer, so we can accurately count the size of the stats.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 24 Aug 2018 20:20:33 +0000 (13:20 -0700)]
Merge branch 'for-4.19' of git://git./linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
"Nothing too interesting. Mostly ahci and ahci_platform changes, many
around power management"
* 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
ata: ahci_platform: enable to get and control reset
ata: libahci_platform: add reset control support
ata: add an extra argument to ahci_platform_get_resources()
ata: sata_rcar: Add r8a77965 support
ata: sata_rcar: exclude setting of PHY registers in Gen3
ata: sata_rcar: really mask all interrupts on Gen2 and later
Revert "ata: ahci_platform: allow disabling of hotplug to save power"
ata: libahci: Allow reconfigure of DEVSLP register
ata: libahci: Correct setting of DEVSLP register
ata: ahci: Enable DEVSLP by default on x86 with SLP_S0
ata: ahci: Support state with min power but Partial low power state
Revert "ata: ahci_platform: convert kcalloc to devm_kcalloc"
ata: sata_rcar: Add rudimentary Runtime PM support
ata: sata_rcar: Provide a short-hand for &pdev->dev
ata: Only output sg element mapped number in verbose debug
ata: Guard ata_scsi_dump_cdb() by ATA_VERBOSE_DEBUG
ata: ahci_platform: convert kcalloc to devm_kcalloc
ata: ahci_platform: convert kzallloc to kcalloc
ata: ahci_platform: correct parameter documentation for ahci_platform_shutdown
libata: remove ata_sff_data_xfer_noirq()
...
Linus Torvalds [Fri, 24 Aug 2018 20:19:27 +0000 (13:19 -0700)]
Merge branch 'for-4.19' of git://git./linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
"Just one commit from Steven to take out spin lock from trace event
handlers"
* 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup/tracing: Move taking of spin lock out of trace event handlers
Linus Torvalds [Fri, 24 Aug 2018 20:16:36 +0000 (13:16 -0700)]
Merge branch 'for-4.19' of git://git./linux/kernel/git/tj/wq
Pull workqueue updates from Tejun Heo:
"Over the lockdep cross-release churn, workqueue lost some of the
existing annotations. Johannes Berg restored it and also improved
them"
* 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: re-add lockdep dependencies for flushing
workqueue: skip lockdep wq dependency in cancel_work_sync()
Linus Torvalds [Fri, 24 Aug 2018 20:10:38 +0000 (13:10 -0700)]
Merge tag 'iommu-updates-v4.19' of git://git./linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- PASID table handling updates for the Intel VT-d driver. It implements
a global PASID space now so that applications usings multiple devices
will just have one PASID.
- A new config option to make iommu passthroug mode the default.
- New sysfs attribute for iommu groups to export the type of the
default domain.
- A debugfs interface (for debug only) usable by IOMMU drivers to
export internals to user-space.
- R-Car Gen3 SoCs support for the ipmmu-vmsa driver
- The ARM-SMMU now aborts transactions from unknown devices and devices
not attached to any domain.
- Various cleanups and smaller fixes all over the place.
* tag 'iommu-updates-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (42 commits)
iommu/omap: Fix cache flushes on L2 table entries
iommu: Remove the ->map_sg indirection
iommu/arm-smmu-v3: Abort all transactions if SMMU is enabled in kdump kernel
iommu/arm-smmu-v3: Prevent any devices access to memory without registration
iommu/ipmmu-vmsa: Don't register as BUS IOMMU if machine doesn't have IPMMU-VMSA
iommu/ipmmu-vmsa: Clarify supported platforms
iommu/ipmmu-vmsa: Fix allocation in atomic context
iommu: Add config option to set passthrough as default
iommu: Add sysfs attribyte for domain type
iommu/arm-smmu-v3: sync the OVACKFLG to PRIQ consumer register
iommu/arm-smmu: Error out only if not enough context interrupts
iommu/io-pgtable-arm-v7s: Abort allocation when table address overflows the PTE
iommu/io-pgtable-arm: Fix pgtable allocation in selftest
iommu/vt-d: Remove the obsolete per iommu pasid tables
iommu/vt-d: Apply per pci device pasid table in SVA
iommu/vt-d: Allocate and free pasid table
iommu/vt-d: Per PCI device pasid table interfaces
iommu/vt-d: Add for_each_device_domain() helper
iommu/vt-d: Move device_domain_info to header
iommu/vt-d: Apply global PASID in SVA
...