OSDN Git Service
David S. Miller [Mon, 25 Oct 2010 20:04:48 +0000 (13:04 -0700)]
tms380tr: Use mdelay() in tms380tr_wait().
This driver tries to do up to half-second udelay()
calls, which overflows on x86-64.
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 25 Oct 2010 19:51:55 +0000 (12:51 -0700)]
net: Increase xmit RECURSION_LIMIT to 10.
Three is definitely too low, and we know from reports that GRE tunnels
stacked as deeply as 37 levels cause stack overflows, so pick some
reasonable value between those two.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Mon, 25 Oct 2010 02:56:47 +0000 (02:56 +0000)]
mlx4_en: Fix out of bounds array access
When searching for a free entry in either mlx4_register_vlan() or
mlx4_register_mac(), and there is no free entry, the loop terminates without
updating the local variable free thus causing out of array bounds access. Fix
this by adding a proper check outside the loop.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joshua Hoke [Mon, 25 Oct 2010 01:44:22 +0000 (01:44 +0000)]
macb: Don't re-enable interrupts while in polling mode
On a busy network, the macb driver could get stuck in the interrupt
handler, quickly triggering the watchdog, due to a confluence of
factors:
1. macb_poll re-enables interrupts unconditionally, even when it will
be called again because it exhausted its rx budget
2. macb_interrupt only disables interrupts after scheduling
macb_poll, but scheduling fails when macb_poll is already scheduled
because it didn't call napi_complete
3. macb_interrupt loops until the interrupt status register is clear,
which will never happen in this case if the driver doesn't disable
the RX interrupt
Since macb_interrupt runs in interrupt context, this effectively locks
up the machine, triggering the hardware watchdog.
This issue was readily reproducible on a flooded network with a
modified 2.6.27.48 kernel. The same problem appears to still be in the
2.6.36-rc8 driver code, so I am submitting this patch against that
version. I have not tested this version of the patch except to make
sure the kernel compiles.
Signed-off-by: Joshua Hoke <joshua.hoke@sixnet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Mon, 25 Oct 2010 01:11:58 +0000 (01:11 +0000)]
be2net: Fix CSO for UDP packets
We're setting skb->ip_summed to CHECKSUM_NONE for all non-TCP pkts, making the stack
recompute checksum.This is a bug for UDP pkts for which cso must be used.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Mon, 25 Oct 2010 01:11:10 +0000 (01:11 +0000)]
be2net: Call netif_carier_off() after register_netdev()
Calling netif_carrier_off before register_netdev was causing the network interface
to miss a linkwatch pending event leading to an inconsistent state if the link
is not up when interface is initialized.This is now invoked after register_netdev.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Divy Le Ray [Mon, 25 Oct 2010 07:35:02 +0000 (07:35 +0000)]
cxgb3: fix device opening error path
Only negative return from bind_qsets() should be considered an error and
propagated.
It fixes an issue reported by IBM on P Series platform.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Tested-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Rothwell [Mon, 25 Oct 2010 05:26:41 +0000 (22:26 -0700)]
l2tp: static functions should not be exported
Causes these build failures on PowerPC:
net/l2tp/l2tp_core.c:1228: error: __ksymtab_l2tp_tunnel_closeall causes a section type conflict
net/l2tp/l2tp_core.c:1228: error: __ksymtab_l2tp_tunnel_closeall causes a section type conflict
net/l2tp/l2tp_core.c:1006: error: __ksymtab_l2tp_xmit_core causes a section type conflict
net/l2tp/l2tp_core.c:1006: error: __ksymtab_l2tp_xmit_core causes a section type conflict
net/l2tp/l2tp_core.c:847: error: __ksymtab_l2tp_udp_recv_core causes a section type conflict
net/l2tp/l2tp_core.c:847: error: __ksymtab_l2tp_udp_recv_core causes a section type conflict
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Dillow [Sun, 24 Oct 2010 10:20:21 +0000 (10:20 +0000)]
typhoon: update to new VLAN acceleration model
Also correct the byteswapping as we keep the TCI in host order.
Signed-off-by: David Dillow <dave@thedillows.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Dillow [Sun, 24 Oct 2010 10:20:20 +0000 (10:20 +0000)]
typhoon: wait for RX mode commands to finish
When adding VLAN devices, we can get several calls to
typhoon_set_rx_mode() in quick succession. Because we didn't wait for
the commands to complete, we could run out of command descriptors and
fail to set the RX mode.
Signed-off-by: David Dillow <dave@thedillows.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 24 Oct 2010 04:27:10 +0000 (04:27 +0000)]
netlink: fix netlink_change_ngroups()
commit
6c04bb18ddd633 (netlink: use call_rcu for netlink_change_ngroups)
used a somewhat convoluted and racy way to perform call_rcu().
The old block of memory is freed after a grace period, but the rcu_head
used to track it is located in new block.
This can clash if we call two times or more netlink_change_ngroups(),
and a block is freed before another. call_rcu() called on different cpus
makes no guarantee in order of callbacks.
Fix this using a more standard way of handling this : Each block of
memory contains its own rcu_head, so that no 'use after free' can
happens.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Johannes Berg <johannes@sipsolutions.net>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Kirjanov [Fri, 22 Oct 2010 05:41:14 +0000 (05:41 +0000)]
slhc: Don't export symbols twice
Don't export symbols twice.
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guo-Fu Tseng [Sun, 24 Oct 2010 23:18:25 +0000 (16:18 -0700)]
jme: Support WoL after shutdown
Adding shutdown function that setup wake if wol is enabled.
Add jme_phy_on in jme_set_100m_half in case it is shutting down
or suspending when interface is down(phy_off by default).
v2 updates:
Removed CONFIG_PM ifdef for jme_set_100m_half and jme_wait_link.
It would be nice if it can be applied to net-2.6 along with other patches
sent few days ago. If it is not appropriate, please ignore the net-2.6
request, and apply it to net-next-2.6 as previous patch. :)
Reported-and-helped-by: Сtac <Taoga@yandex.ru>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Balazs Scheidler [Sat, 23 Oct 2010 04:48:14 +0000 (04:48 +0000)]
tproxy: Add missing CAP_NET_ADMIN check to ipv6 side
IP_TRANSPARENT requires root (more precisely CAP_NET_ADMIN privielges)
for IPV6.
However as I see right now this check was missed from the IPv6
implementation.
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Thu, 21 Oct 2010 18:05:34 +0000 (18:05 +0000)]
vmxnet3: fix typo setting confPA
It's a le64, not a le32, typo in one place only.
Noticed by sparse:
drivers/net/vmxnet3/vmxnet3_drv.c:2668:52: warning: incorrect type in assignment (different base types)
drivers/net/vmxnet3/vmxnet3_drv.c:2668:52: expected restricted __le64 [usertype] confPA
drivers/net/vmxnet3/vmxnet3_drv.c:2668:52: got restricted __le32 [usertype] <noident>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Thu, 21 Oct 2010 18:05:33 +0000 (18:05 +0000)]
vmxnet3: annotate hwaddr members as __iomem pointers
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Thu, 21 Oct 2010 18:05:32 +0000 (18:05 +0000)]
vmxnet3: remove set_flag_le{16,64} helpers
It's easier to just annotate the constants as little endian types and set/clear
the flags directly.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dimitris Michailidis [Thu, 21 Oct 2010 11:29:56 +0000 (11:29 +0000)]
cxgb4: update to utilize the newer VLAN infrastructure
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dimitris Michailidis [Thu, 21 Oct 2010 11:29:55 +0000 (11:29 +0000)]
cxgb4: fix crash due to manipulating queues before registration
Before commit "net: allocate tx queues in register_netdevice"
netif_tx_stop_all_queues and related functions could be used between
device allocation and registration but now only after registration.
cxgb4 has such a call before registration and crashes now. Move it
after register_netdev.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andre B. Oliveira [Mon, 18 Oct 2010 21:47:27 +0000 (21:47 +0000)]
can: tscan1: add driver for TS-CAN1 boards
Add driver for Technologic Systems TS-CAN1 PC104 peripheral boards.
Signed-off-by: Andre B. Oliveira <anbadeol@gmail.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anders Franzen [Tue, 19 Oct 2010 03:50:47 +0000 (03:50 +0000)]
ip6_tunnel dont update the mtu on the route.
The ip6_tunnel device did not unset the flag,
IFF_XMIT_DST_RELEASE. This will make the dev layer
to release the dst before calling the tunnel.
The tunnel will not update any mtu/pmtu info, since
it does not have a dst on the skb.
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Gortmaker [Mon, 18 Oct 2010 12:14:44 +0000 (12:14 +0000)]
pktgen: clean up handling of local/transient counter vars
The temporary variable "i" is needlessly initialized to zero
in two distinct cases in this file:
1) where it is set to zero and then used as an argument in an addition
before being assigned a non-zero value.
2) where it is only used in a standard/typical loop counter
For (1), simply delete assignment to zero and usages while still
zero; for (2) simply make the loop start at zero as per standard
practice as seen everywhere else in the same file.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Thu, 21 Oct 2010 07:50:57 +0000 (07:50 +0000)]
e1000: make e1000_reinit_safe local
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Thu, 21 Oct 2010 07:50:56 +0000 (07:50 +0000)]
bnx2x: make local function static and remove dead code
Make many functions that are only used in one file static.
Remove dead code for override_led_value.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Thu, 21 Oct 2010 07:50:55 +0000 (07:50 +0000)]
qlge: disable unsed dump code
The driver has lots of unused code to dump data structures to
console. Use existing simple way to remove the code with ifdef.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Thu, 21 Oct 2010 07:50:54 +0000 (07:50 +0000)]
qlge: make local functions static
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Thu, 21 Oct 2010 07:50:53 +0000 (07:50 +0000)]
vxge: make functions local and remove dead code
Use results of make namespacecheck to make functions local and
remove code that is not used.
Also rename initialize_ethtool_ops to vxge_initialize_ethtool_ops.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Thu, 21 Oct 2010 08:37:41 +0000 (08:37 +0000)]
phylib: make local function static
The following functions are not used directly by any drivers:
phy_attach_direct
phy_device_create
phy_prepare_link
genphy_config_advert
genphy_setup_forced
phy_config_interrupt
phy_clear_interrypt
phy_sanitize_settings
phy_enable_interrupts
phy_disable_interrupts
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Thu, 21 Oct 2010 07:50:50 +0000 (07:50 +0000)]
atlx: make local functions/data static
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Thu, 21 Oct 2010 07:50:49 +0000 (07:50 +0000)]
atl1c: make functions static
The up/down are only used in this file.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Thu, 21 Oct 2010 07:50:48 +0000 (07:50 +0000)]
benet: make be_poll_rx local
Only used in one file.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Thu, 21 Oct 2010 07:50:47 +0000 (07:50 +0000)]
benet: remove dead code
The following code and data are defined but never used in current
driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Thu, 21 Oct 2010 07:50:46 +0000 (07:50 +0000)]
l2tp: make local function static
Also moved the refcound inlines from l2tp_core.h to l2tp_core.c
since only used in that one file.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Thu, 21 Oct 2010 06:59:20 +0000 (06:59 +0000)]
mlx4: make functions local and remove dead code.
Make the following function static: mlx4_UNMAP_ICM
Remove the following unused function: mlx4_MAP_ICM_page
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde [Thu, 21 Oct 2010 01:01:22 +0000 (01:01 +0000)]
can: at91_can: add KBUILD_MODNAME to bittiming constant
While there replace all usage of self defined DRV_NAME by KBUILD_MODNAME.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde [Thu, 21 Oct 2010 01:01:21 +0000 (01:01 +0000)]
can: at91_can: convert dev_<level> printing to netdev_<level>
While there, remove "printk()" on driver loading.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde [Thu, 21 Oct 2010 01:01:20 +0000 (01:01 +0000)]
can: at91_can: convert readl, writel their __raw pendants
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde [Thu, 21 Oct 2010 01:01:19 +0000 (01:01 +0000)]
can: at91_can: set bittiming in chip_start
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde [Thu, 21 Oct 2010 01:01:18 +0000 (01:01 +0000)]
can: at91_can: implement and use at91_get_berr_counter
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde [Thu, 21 Oct 2010 01:01:17 +0000 (01:01 +0000)]
can: at91_can: fix section mismatch warning
...by adding the correct annotation "__devinit" to the driver's probe
function.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde [Thu, 21 Oct 2010 01:01:16 +0000 (01:01 +0000)]
can: at91_can: fix compiler warning in at91_irq_err_state
This patch fixes the following compiler warning:
drivers/net/can/at91_can.c: In function 'at91_irq_err_state':
drivers/net/can/at91_can.c:779: warning: 'reg_ier' may be used uninitialized in this function
drivers/net/can/at91_can.c:779: warning: 'reg_idr' may be used uninitialized in this function
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde [Thu, 21 Oct 2010 01:01:15 +0000 (01:01 +0000)]
can: at91_can: fix use after free of priv
The priv is part of the memory allocated by alloc_candev().
This patch moved the free it after last usage of priv.
While there convert all free_netdev() to free_candev() (which is currently
just a wrapper around free_netdev()) to be symetrically with the allocation
via alloc_candev().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde [Thu, 21 Oct 2010 01:01:14 +0000 (01:01 +0000)]
can: at91_can: fix reception of extended frames
The AT91_MID_MIDE bit must be set in order to receive extended frames.
The reception of an extended frame sets this bit, while reception of
standard frames resets it. This results in some lost extended frames in
an extended ID only environment. But leads to unpredictable lost
extended ID frames in a mixed environment.
The problem is fixed by setting the AT91_MID_MIDE after reception of a
CAN frame.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde [Thu, 21 Oct 2010 01:01:13 +0000 (01:01 +0000)]
can: at91_can: use correct bit to enable CAN_CTRLMODE_3_SAMPLES
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Masayuki Ohtake [Fri, 15 Oct 2010 03:00:28 +0000 (03:00 +0000)]
can: Topcliff: Add PCH_CAN driver.
CAN driver of Topcliff PCH
Topcliff PCH is the platform controller hub that is going to be used in
Intel's upcoming general embedded platform. All IO peripherals in
Topcliff PCH are actually devices sitting on AMBA bus.
Topcliff PCH has CAN I/F. This driver enables CAN function.
Signed-off-by: Masayuki Ohtake <masa-korg@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tejun Heo [Thu, 14 Oct 2010 23:55:22 +0000 (23:55 +0000)]
connector: remove lazy workqueue creation
Commit
1a5645bc (connector: create connector workqueue only while
needed once) implements lazy workqueue creation for connector
workqueue. With cmwq now in place, lazy workqueue creation doesn't
make much sense while adding a lot of complexity. Remove it and
allocate an ordered workqueue during initialization.
This also removes a call to flush_scheduled_work() which is deprecated
and scheduled to be removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 24 Oct 2010 20:41:39 +0000 (13:41 -0700)]
Merge branch 'for-next' of git://git./linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
Update broken web addresses in arch directory.
Update broken web addresses in the kernel.
Revert "drivers/usb: Remove unnecessary return's from void functions" for musb gadget
Revert "Fix typo: configuation => configuration" partially
ida: document IDA_BITMAP_LONGS calculation
ext2: fix a typo on comment in ext2/inode.c
drivers/scsi: Remove unnecessary casts of private_data
drivers/s390: Remove unnecessary casts of private_data
net/sunrpc/rpc_pipe.c: Remove unnecessary casts of private_data
drivers/infiniband: Remove unnecessary casts of private_data
drivers/gpu/drm: Remove unnecessary casts of private_data
kernel/pm_qos_params.c: Remove unnecessary casts of private_data
fs/ecryptfs: Remove unnecessary casts of private_data
fs/seq_file.c: Remove unnecessary casts of private_data
arm: uengine.c: remove C99 comments
arm: scoop.c: remove C99 comments
Fix typo configue => configure in comments
Fix typo: configuation => configuration
Fix typo interrest[ing|ed] => interest[ing|ed]
Fix various typos of valid in comments
...
Fix up trivial conflicts in:
drivers/char/ipmi/ipmi_si_intf.c
drivers/usb/gadget/rndis.c
net/irda/irnet/irnet_ppp.c
Linus Torvalds [Sun, 24 Oct 2010 20:06:57 +0000 (13:06 -0700)]
Merge branch 'devel' of git://git./linux/kernel/git/mchehab/edac
* 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/edac: (25 commits)
i7300_edac: Properly initialize per-csrow memory size
V4L/DVB: i7300_edac: better initialize page counts
MAINTAINERS: Add maintainer for i7300-edac driver
i7300-edac: CodingStyle cleanup
i7300_edac: Improve comments
i7300_edac: Cleanup: reorganize the file contents
i7300_edac: Properly detect channel on CE errors
i7300_edac: enrich FBD error info for corrected errors
i7300_edac: enrich FBD error info for fatal errors
i7300_edac: pre-allocate a buffer used to prepare err messages
i7300_edac: Fix MTR x4/x8 detection logic
i7300_edac: Make the debug messages coherent with the others
i7300_edac: Cleanup: remove get_error_info logic
i7300_edac: Add a code to cleanup error registers
i7300_edac: Add support for reporting FBD errors
i7300_edac: Properly detect the type of error correction
i7300_edac: Detect if the device is on single mode
i7300_edac: Adds detection for enhanced scrub mode on x8
i7300_edac: Clear the error bit after reading
i7300_edac: Add error detection code for global errors
...
Linus Torvalds [Sun, 24 Oct 2010 19:47:55 +0000 (12:47 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/penberg/slab-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6: (27 commits)
SLUB: Fix memory hotplug with !NUMA
slub: Move functions to reduce #ifdefs
slub: Enable sysfs support for !CONFIG_SLUB_DEBUG
SLUB: Optimize slab_free() debug check
slub: Move NUMA-related functions under CONFIG_NUMA
slub: Add lock release annotation
slub: Fix signedness warnings
slub: extract common code to remove objects from partial list without locking
SLUB: Pass active and inactive redzone flags instead of boolean to debug functions
slub: reduce differences between SMP and NUMA
Revert "Slub: UP bandaid"
percpu: clear memory allocated with the km allocator
percpu: use percpu allocator on UP too
percpu: reduce PCPU_MIN_UNIT_SIZE to 32k
vmalloc: pcpu_get/free_vm_areas() aren't needed on UP
SLUB: Fix merged slab cache names
Slub: UP bandaid
slub: fix SLUB_RESILIENCY_TEST for dynamic kmalloc caches
slub: Fix up missing kmalloc_cache -> kmem_cache_node case for memoryhotplug
slub: Add dummy functions for the !SLUB_DEBUG case
...
Linus Torvalds [Sun, 24 Oct 2010 19:47:25 +0000 (12:47 -0700)]
Merge branch 'kvm-updates/2.6.37' of git://git./virt/kvm/kvm
* 'kvm-updates/2.6.37' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (321 commits)
KVM: Drop CONFIG_DMAR dependency around kvm_iommu_map_pages
KVM: Fix signature of kvm_iommu_map_pages stub
KVM: MCE: Send SRAR SIGBUS directly
KVM: MCE: Add MCG_SER_P into KVM_MCE_CAP_SUPPORTED
KVM: fix typo in copyright notice
KVM: Disable interrupts around get_kernel_ns()
KVM: MMU: Avoid sign extension in mmu_alloc_direct_roots() pae root address
KVM: MMU: move access code parsing to FNAME(walk_addr) function
KVM: MMU: audit: check whether have unsync sps after root sync
KVM: MMU: audit: introduce audit_printk to cleanup audit code
KVM: MMU: audit: unregister audit tracepoints before module unloaded
KVM: MMU: audit: fix vcpu's spte walking
KVM: MMU: set access bit for direct mapping
KVM: MMU: cleanup for error mask set while walk guest page table
KVM: MMU: update 'root_hpa' out of loop in PAE shadow path
KVM: x86 emulator: Eliminate compilation warning in x86_decode_insn()
KVM: x86: Fix constant type in kvm_get_time_scale
KVM: VMX: Add AX to list of registers clobbered by guest switch
KVM guest: Move a printk that's using the clock before it's ready
KVM: x86: TSC catchup mode
...
Linus Torvalds [Sun, 24 Oct 2010 19:46:24 +0000 (12:46 -0700)]
Merge branch 'i2c-for-linus' of git://git./linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-viapro: Don't log nacks
i2c/pca954x: Remove __devinit and __devexit from probe and remove functions
MAINTAINERS: Add maintainer for PCA9541 I2C bus master selector driver
i2c/mux: Driver for PCA9541 I2C Master Selector
i2c: Optimize function i2c_detect()
i2c: Discard warning message on device instantiation from user-space
i2c-amd8111: Add proper error handling
i2c: Change to new flag variable
i2c: Remove unneeded inclusions of <linux/i2c-id.h>
i2c: Let i2c_parent_is_i2c_adapter return the parent adapter
i2c: Simplify i2c_parent_is_i2c_adapter
i2c-pca-platform: Change device name of request_irq
i2c: Fix Kconfig dependencies
Linus Torvalds [Sun, 24 Oct 2010 19:44:59 +0000 (12:44 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (47 commits)
HID: fix mismerge in hid-lg
HID: hidraw: fix window in hidraw_release
HID: hid-sony: override usbhid_output_raw_report for Sixaxis
HID: add absolute axis resolution calculation
HID: force feedback support for Logitech RumblePad gamepad
HID: support STmicroelectronics and Sitronix with hid-stantuml driver
HID: magicmouse: Adjust major / minor axes to scale
HID: Fix for problems with eGalax/DWAV multi-touch-screen
HID: waltop: add support for Waltop Slim Tablet 12.1 inch
HID: add NOGET quirk for AXIS 295 Video Surveillance Joystick
HID: usbhid: remove unused hiddev_driver
HID: magicmouse: Use hid-input parsing rather than bypassing it
HID: trivial formatting fix
HID: Add support for Logitech Speed Force Wireless gaming wheel
HID: don't Send Feature Reports on Interrupt Endpoint
HID: 3m: Adjust major / minor axes to scale
HID: 3m: Correct touchscreen emulation
HID: 3m: Convert to MT slots
HID: 3m: Output proper orientation range
HID: 3m: Adjust to sequential MT HID protocol
...
Linus Torvalds [Sun, 24 Oct 2010 19:44:34 +0000 (12:44 -0700)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: Makefile - replace the use of <module>-objs with <module>-y
crypto: hifn_795x - use cancel_delayed_work_sync()
crypto: talitos - sparse check endian fixes
crypto: talitos - fix checkpatch warning
crypto: talitos - fix warning: 'alg' may be used uninitialized in this function
crypto: cryptd - Adding the AEAD interface type support to cryptd
crypto: n2_crypto - Niagara2 driver needs to depend upon CRYPTO_DES
crypto: Kconfig - update broken web addresses
crypto: omap-sham - Adjust DMA parameters
crypto: fips - FIPS requires algorithm self-tests
crypto: omap-aes - OMAP2/3 AES hw accelerator driver
crypto: updates to enable omap aes
padata: add missing __percpu markup in include/linux/padata.h
MAINTAINERS: Add maintainer entries for padata/pcrypt
Pekka Enberg [Sun, 24 Oct 2010 16:57:05 +0000 (19:57 +0300)]
Merge branch 'master' into for-linus
Conflicts:
include/linux/percpu.h
mm/percpu.c
Jean Delvare [Sun, 24 Oct 2010 16:16:59 +0000 (18:16 +0200)]
i2c-viapro: Don't log nacks
Transactions not acked can happen every now and then, in particular
during device detection, and various transaction types can be used for
this purpose. So stop logging this event, except when debugging is
enabled. This is what other similar drivers (e.g. i2c-i801 or
i2c-piix4) do.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Guenter Roeck [Sun, 24 Oct 2010 16:16:59 +0000 (18:16 +0200)]
i2c/pca954x: Remove __devinit and __devexit from probe and remove functions
The underlying I2C adapter may or may not be present when this driver
gets initialized, and may disappear later, so there is no safe time at
which the probe and remove functions can be discarded.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Guenter Roeck [Sun, 24 Oct 2010 16:16:59 +0000 (18:16 +0200)]
MAINTAINERS: Add maintainer for PCA9541 I2C bus master selector driver
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Guenter Roeck [Sun, 24 Oct 2010 16:16:58 +0000 (18:16 +0200)]
i2c/mux: Driver for PCA9541 I2C Master Selector
This patch adds support for PCA9541, an I2C Bus Master Selector.
The driver is modeled as single channel I2C Multiplexer to be able to utilize
the I2C multiplexer framework.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Sun, 24 Oct 2010 16:16:58 +0000 (18:16 +0200)]
i2c: Optimize function i2c_detect()
Check the class flags before allocating the temporary i2c_client
structure, to avoid allocating it when we don't need it.
Also optimize the inner loop a bit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Jean Delvare [Sun, 24 Oct 2010 16:16:58 +0000 (18:16 +0200)]
i2c: Discard warning message on device instantiation from user-space
The "new_device" sysfs interface has been there for quite some time
now, nobody complained about it so it must be good enough. Time to
remove the warning and call it stable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Michael Lawnick <ml.lawnick@gmx.de>
Julia Lawall [Sun, 24 Oct 2010 16:16:58 +0000 (18:16 +0200)]
i2c-amd8111: Add proper error handling
The functions the functions amd_ec_wait_write and amd_ec_wait_read have an
unsigned return type, but return a negative constant to indicate an error
condition.
A sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@exists@
identifier f;
constant C;
@@
unsigned f(...)
{ <+...
* return -C;
...+> }
// </smpl>
Fixing amd_ec_wait_write and amd_ec_wait_read leads to the need to adjust
the return type of the functions amd_ec_write and amd_ec_read, which are
the only functions that call amd_ec_wait_write and amd_ec_wait_read.
amd_ec_write and amd_ec_read, in turn, are only called from within the
function amd8111_access, which already returns a signed typed value. Each
of the calls to amd_ec_write and amd_ec_read are updated using the
following semantic patch:
// <smpl>
@@
@@
+ status = amd_ec_write
- amd_ec_write
(...);
+ if (status) return status;
@@
@@
+ status = amd_ec_read
- amd_ec_read
(...);
+ if (status) return status;
// </smpl>
The patch also adds the declaration of the status variable.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
matt mooney [Sun, 24 Oct 2010 16:16:58 +0000 (18:16 +0200)]
i2c: Change to new flag variable
Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Sun, 24 Oct 2010 16:16:58 +0000 (18:16 +0200)]
i2c: Remove unneeded inclusions of <linux/i2c-id.h>
These drivers don't use anything which is defined in <linux/i2c-id.h>.
This header file was never meant to be included directly anyway, and
will be deleted soon.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Jean Delvare [Sun, 24 Oct 2010 16:16:57 +0000 (18:16 +0200)]
i2c: Let i2c_parent_is_i2c_adapter return the parent adapter
This makes the calling site's code clearer IMHO.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Michael Lawnick <ml.lawnick@gmx.de>
Jean Delvare [Sun, 24 Oct 2010 16:16:57 +0000 (18:16 +0200)]
i2c: Simplify i2c_parent_is_i2c_adapter
Only i2c devices can have their type set to i2c_adapter_type, so
testing the bus type is redundant.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
Nobuhiro Iwamatsu [Sun, 24 Oct 2010 16:16:57 +0000 (18:16 +0200)]
i2c-pca-platform: Change device name of request_irq
i2c->adap.name shouldn't be used in request_irq.
Instead the driver name "i2c-pca-platform" should be used.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Sun, 24 Oct 2010 16:16:57 +0000 (18:16 +0200)]
i2c: Fix Kconfig dependencies
drivers/i2c/algos/Kconfig makes all the algorithms dependent on
!I2C_HELPER_AUTO, which triggers a Kconfig warning about broken
dependencies when some driver selects one of the algorithms. Ideally
we would make only the prompts dependent on !I2C_HELPER_AUTO, however
Kconfig doesn't currently support that. So we have to redefine the
symbols separately for the I2C_HELPER_AUTO=y case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Michal Marek <mmarek@suse.cz>
Jan Kiszka [Mon, 18 Oct 2010 13:38:40 +0000 (15:38 +0200)]
KVM: Drop CONFIG_DMAR dependency around kvm_iommu_map_pages
We also have to call kvm_iommu_map_pages for CONFIG_AMD_IOMMU. So drop
the dependency on Intel IOMMU, kvm_iommu_map_pages will be a nop anyway
if CONFIG_IOMMU_API is not defined.
KVM-Stable-Tag.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Jan Kiszka [Thu, 14 Oct 2010 11:59:04 +0000 (13:59 +0200)]
KVM: Fix signature of kvm_iommu_map_pages stub
Breaks otherwise if CONFIG_IOMMU_API is not set.
KVM-Stable-Tag.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Huang Ying [Fri, 8 Oct 2010 08:24:15 +0000 (16:24 +0800)]
KVM: MCE: Send SRAR SIGBUS directly
Originally, SRAR SIGBUS is sent to QEMU-KVM via touching the poisoned
page. But commit
96054569190bdec375fe824e48ca1f4e3b53dd36 prevents the
signal from being sent. So now the signal is sent via
force_sig_info_fault directly.
[marcelo: use send_sig_info instead]
Reported-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Huang Ying [Fri, 8 Oct 2010 08:24:14 +0000 (16:24 +0800)]
KVM: MCE: Add MCG_SER_P into KVM_MCE_CAP_SUPPORTED
Now we have MCG_SER_P (and corresponding SRAO/SRAR MCE) support in
kernel and QEMU-KVM, the MCG_SER_P should be added into
KVM_MCE_CAP_SUPPORTED to make all these code really works.
Reported-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Nicolas Kaiser [Wed, 6 Oct 2010 12:23:22 +0000 (14:23 +0200)]
KVM: fix typo in copyright notice
Fix typo in copyright notice.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Avi Kivity [Mon, 4 Oct 2010 10:55:49 +0000 (12:55 +0200)]
KVM: Disable interrupts around get_kernel_ns()
get_kernel_ns() wants preemption disabled. It doesn't make a lot of sense
during the get/set ioctls (no way to make them non-racy) but the callee wants
it.
Signed-off-by: Avi Kivity <avi@redhat.com>
Avi Kivity [Sun, 3 Oct 2010 16:51:39 +0000 (18:51 +0200)]
KVM: MMU: Avoid sign extension in mmu_alloc_direct_roots() pae root address
Signed-off-by: Avi Kivity <avi@redhat.com>
Xiao Guangrong [Tue, 28 Sep 2010 09:03:14 +0000 (17:03 +0800)]
KVM: MMU: move access code parsing to FNAME(walk_addr) function
Move access code parsing from caller site to FNAME(walk_addr) function
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Xiao Guangrong [Mon, 27 Sep 2010 10:09:29 +0000 (18:09 +0800)]
KVM: MMU: audit: check whether have unsync sps after root sync
After root synced, all unsync sps are synced, this patch add a check to make
sure it's no unsync sps in VCPU's page table
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Xiao Guangrong [Mon, 27 Sep 2010 10:07:59 +0000 (18:07 +0800)]
KVM: MMU: audit: introduce audit_printk to cleanup audit code
Introduce audit_printk, and record audit point instead audit name
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Xiao Guangrong [Mon, 27 Sep 2010 10:07:07 +0000 (18:07 +0800)]
KVM: MMU: audit: unregister audit tracepoints before module unloaded
fix:
Call Trace:
[<
ffffffffa01e46ba>] ? kvm_mmu_pte_write+0x229/0x911 [kvm]
[<
ffffffffa01c6ba9>] ? gfn_to_memslot+0x39/0xa0 [kvm]
[<
ffffffffa01c6c26>] ? mark_page_dirty+0x16/0x2e [kvm]
[<
ffffffffa01c6d6f>] ? kvm_write_guest_page+0x67/0x7f [kvm]
[<
ffffffff81066fbd>] ? local_clock+0x2a/0x3b
[<
ffffffffa01d52ce>] emulator_write_phys+0x46/0x54 [kvm]
......
Code: Bad RIP value.
RIP [<
ffffffffa0172056>] 0xffffffffa0172056
RSP <
ffff880134f69a70>
CR2:
ffffffffa0172056
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Xiao Guangrong [Mon, 27 Sep 2010 10:06:16 +0000 (18:06 +0800)]
KVM: MMU: audit: fix vcpu's spte walking
After nested nested paging, it may using long mode to shadow 32/PAE paging
guest, so this patch fix it
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Xiao Guangrong [Mon, 27 Sep 2010 10:05:00 +0000 (18:05 +0800)]
KVM: MMU: set access bit for direct mapping
Set access bit while setup up direct page table if it's nonpaing or npt enabled,
it's good for CPU's speculate access
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Xiao Guangrong [Mon, 27 Sep 2010 10:03:27 +0000 (18:03 +0800)]
KVM: MMU: cleanup for error mask set while walk guest page table
Small cleanup for set page fault error code
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Xiao Guangrong [Mon, 27 Sep 2010 10:02:12 +0000 (18:02 +0800)]
KVM: MMU: update 'root_hpa' out of loop in PAE shadow path
The value of 'vcpu->arch.mmu.pae_root' is not modified, so we can update
'root_hpa' out of the loop.
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Sheng Yang [Tue, 28 Sep 2010 08:33:32 +0000 (16:33 +0800)]
KVM: x86 emulator: Eliminate compilation warning in x86_decode_insn()
Eliminate:
arch/x86/kvm/emulate.c:801: warning: ‘sv’ may be used uninitialized in this
function
on gcc 4.1.2
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Jan Kiszka [Sun, 26 Sep 2010 11:00:53 +0000 (13:00 +0200)]
KVM: x86: Fix constant type in kvm_get_time_scale
Older gcc versions complain about the improper type (for x86-32), 4.5
seems to fix this silently. However, we should better use the right type
initially.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Jan Kiszka [Tue, 28 Sep 2010 14:37:42 +0000 (16:37 +0200)]
KVM: VMX: Add AX to list of registers clobbered by guest switch
By chance this caused no harm so far. We overwrite AX during switch
to/from guest context, so we must declare this.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Arjan Koers [Mon, 2 Aug 2010 21:35:28 +0000 (23:35 +0200)]
KVM guest: Move a printk that's using the clock before it's ready
Fix a hang during SMP kernel boot on KVM that showed up
after commit
489fb490dbf8dab0249ad82b56688ae3842a79e8
(2.6.35) and
59aab522154a2f17b25335b63c1cf68a51fb6ae0
(2.6.34.1). The problem only occurs when
CONFIG_PRINTK_TIME is set.
KVM-Stable-Tag.
Signed-off-by: Arjan Koers <0h61vkll2ly8@xutrox.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Zachary Amsden [Sun, 19 Sep 2010 00:38:15 +0000 (14:38 -1000)]
KVM: x86: TSC catchup mode
Negate the effects of AN TYM spell while kvm thread is preempted by tracking
conversion factor to the highest TSC rate and catching the TSC up when it has
fallen behind the kernel view of time. Note that once triggered, we don't
turn off catchup mode.
A slightly more clever version of this is possible, which only does catchup
when TSC rate drops, and which specifically targets only CPUs with broken
TSC, but since these all are considered unstable_tsc(), this patch covers
all necessary cases.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Zachary Amsden [Sun, 19 Sep 2010 00:38:14 +0000 (14:38 -1000)]
KVM: x86: Rename timer function
This just changes some names to better reflect the usage they
will be given. Separated out to keep confusion to a minimum.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Zachary Amsden [Sun, 19 Sep 2010 00:38:13 +0000 (14:38 -1000)]
KVM: x86: Make math work for other scales
The math in kvm_get_time_scale relies on the fact that
NSEC_PER_SEC < 2^32. To use the same function to compute
arbitrary time scales, we must extend the first reduction
step to shrink the base rate to a 32-bit value, and
possibly reduce the scaled rate into a 32-bit as well.
Note we must take care to avoid an arithmetic overflow
when scaling up the tps32 value (this could not happen
with the fixed scaled value of NSEC_PER_SEC, but can
happen with scaled rates above 2^31.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Avi Kivity [Tue, 21 Sep 2010 17:59:44 +0000 (19:59 +0200)]
KVM: cpu_relax() during spin waiting for reboot
It doesn't really matter, but if we spin, we should spin in a more relaxed
manner. This way, if something goes wrong at least it won't contribute to
global warming.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Avi Kivity [Sun, 19 Sep 2010 12:34:08 +0000 (14:34 +0200)]
KVM: VMX: Respect interrupt window in big real mode
If an interrupt is pending, we need to stop emulation so we
can inject it.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Mohammed Gamal [Sun, 19 Sep 2010 12:34:07 +0000 (14:34 +0200)]
KVM: VMX: Emulated real mode interrupt injection
Replace the inject-as-software-interrupt hack we currently have with
emulated injection.
Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Mohammed Gamal [Sun, 19 Sep 2010 12:34:06 +0000 (14:34 +0200)]
KVM: Add kvm_inject_realmode_interrupt() wrapper
This adds a wrapper function kvm_inject_realmode_interrupt() around the
emulator function emulate_int_real() to allow real mode interrupt injection.
[avi: initialize operand and address sizes before emulating interrupts]
[avi: initialize rip for real mode interrupt injection]
[avi: clear interrupt pending flag after emulating interrupt injection]
Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Mohammed Gamal [Sun, 19 Sep 2010 12:34:05 +0000 (14:34 +0200)]
KVM: x86 emulator: Expose emulate_int_real()
Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Hillf Danton [Sat, 18 Sep 2010 00:41:02 +0000 (08:41 +0800)]
KVM: MMU: fix counting of rmap entries in rmap_add()
It seems that rmap entries are under counted.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Xiao Guangrong [Mon, 20 Sep 2010 14:17:48 +0000 (22:17 +0800)]
KVM: document 'kvm.mmu_audit' parameter
Document this parameter into Documentation/kernel-parameters.txt
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Xiao Guangrong [Mon, 20 Sep 2010 14:16:45 +0000 (22:16 +0800)]
KVM: fix the description of kvm-amd.nested in documentation
The default state of 'kvm-amd.nested' is enabled now, so fix the documentation
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Gleb Natapov [Mon, 20 Sep 2010 08:15:32 +0000 (10:15 +0200)]
KVM: SVM: do not generate "external interrupt exit" if other exit is pending
Nested SVM checks for external interrupt after injecting nested exception.
In case there is external interrupt pending the code generates "external
interrupt exit" and overwrites previous exit info. If previously injected
exception already generated exit it will be lost.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Avi Kivity [Sun, 19 Sep 2010 16:44:07 +0000 (18:44 +0200)]
KVM: Convert PIC lock from raw spinlock to ordinary spinlock
The PIC code used to be called from preempt_disable() context, which
wasn't very good for PREEMPT_RT. That is no longer the case, so move
back from raw_spinlock_t to spinlock_t.
Signed-off-by: Avi Kivity <avi@redhat.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Zachary Amsden [Sun, 19 Sep 2010 00:38:12 +0000 (14:38 -1000)]
KVM: x86: Fix kvmclock bug
If preempted after kvmclock values are updated, but before hardware
virtualization is entered, the last tsc time as read by the guest is
never set. It underflows the next time kvmclock is updated if there
has not yet been a successful entry / exit into hardware virt.
Fix this by simply setting last_tsc to the newly read tsc value so
that any computed nsec advance of kvmclock is nulled.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>