OSDN Git Service
Paul Walmsley [Thu, 3 Jul 2008 09:24:45 +0000 (12:24 +0300)]
ARM: OMAP2: Clock: Add OMAP3 DPLL autoidle functions
This patch adds support for DPLL autoidle control to the OMAP3 clock
framework. These functions will be used by the noncore DPLL enable
and disable code - this is because, according to the CDP code, the
DPLL autoidle status must be saved and restored across DPLL
lock/bypass/off transitions.
N.B.: the CORE DPLL (DPLL3) has three autoidle mode options, rather
than just two. This code currently does not support the third option,
low-power bypass autoidle.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Thu, 3 Jul 2008 09:24:45 +0000 (12:24 +0300)]
ARM: OMAP: Add OMAP chip type structure; clean up mach-omap2/id.c
Add a new OMAP chip identification interface, omap_chip_id.
omap_chip_id is a structure which contains one bit for each OMAP2/3
CPU type, and on 3430, ES level. For example, the CHIP_IS_OMAP2420
bit is set in omap_chip at boot on an OMAP2420. On OMAP3430ES2, both
CHIP_IS_OMAP3430 and CHIP_IS_OMAP3430ES2 bits are set.
omap_chip is set in mach-omap2/id.c by _set_omap_chip(). Other
code should use the omap_chip_is() function to test against omap_chip.
Also, clean up id.c by splitting some code out of
omap_check_revision() into its own function, _set_system_rev(); and
converting some debug printk()s into pr_debug().
Second revision.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 3 Jul 2008 09:24:44 +0000 (12:24 +0300)]
ARM: OMAP: Turn CM and PRM access into functions
Otherwise compiling in omap2 and omap3 will not work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 3 Jul 2008 09:24:44 +0000 (12:24 +0300)]
ARM: OMAP: Introduce omap_globals and prcm access functions for multi-omap
New struct omap_globals contains the omap processor specific
module bases. Use omap_globals to set the various base addresses
to make detecting omap chip type simpler.
Also introduce OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS for future multi-omap
patches.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 3 Jul 2008 09:24:43 +0000 (12:24 +0300)]
ARM: OMAP: Remove __REG access for multi-omap
This does not play nicely with multi-omap as it cannot be replaced
by a function in io.c for omaps with different IO bases.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 3 Jul 2008 09:24:43 +0000 (12:24 +0300)]
ARM: OMAP: USB: Change omap USB code to use omap_read/write instead of __REG
Change omap USB code to use omap_read/write instead of __REG for multi-omap
Cc: David Brownell <david-b@pacbell.net>
Cc: linux-usb@vger.kernel.org
Cc: i2c@lm-sensors.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 3 Jul 2008 09:24:41 +0000 (12:24 +0300)]
ARM: OMAP: Change omap_cf.c and omap_nor.c to use omap_readw/writew instead of __REG
Change omap_cf.c and omap_nor.c to use omap_readw/writew instead of __REG.
This is needed for multi-omap in the future.
Cc: David Brownell <david-b@pacbell.net>
Cc: linux-pcmcia@lists.infradead.org
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Tony Lindren <tony@atomide.com>
Hiroshi DOYU [Thu, 3 Jul 2008 09:24:41 +0000 (12:24 +0300)]
ARM: OMAP: CLKFW: Initial debugfs support for omap clock framework
debugfs can provide the infrastructure to trace the dependencies of
clock tree hierarchy quite visibly. This patch enables to keep track
of clock tree hierarchy and expose their attributes under each clock
directry as below:
omap:~# tree -d -L 2 /debug/clock/omap_32k_fck/
/debug/clock/omap_32k_fck/
|-- gpt10_fck
|-- gpt11_fck
|-- gpt1_fck
|-- per_32k_alwon_fck
| |-- gpio2_fck
| |-- gpio3_fck
| |-- gpio4_fck
| |-- gpio5_fck
| |-- gpio6_fck
| `-- wdt3_fck
|-- ts_fck
`-- wkup_32k_fck
|-- gpio1_fck
`-- wdt2_fck
14 directories
omap:~# tree /debug/clock/omap_32k_fck/gpt10_fck/
/debug/clock/omap_32k_fck/gpt10_fck/
|-- flags
|-- rate
`-- usecount
0 directories, 3 files
Although, compared with David Brownell's small patch, this may look
bit overkilling, I expect that this debugfs can deal with other PRCM
complexities at the same time. For example, powerdomain dependencies
can be expressed by using symbolic links of these clocks if
powerdomain supports dubgfs as well.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 3 Jul 2008 09:24:41 +0000 (12:24 +0300)]
ARM: OMAP: Clean up interrupt lines to fix warnings for multi-omap
If boards with different NR_IRQS are compiled together, tons of
compiler warnings are emitted about redefining NR_IRQS.
This patch fixes the problem by adding up NR_IRQS in a common place.
Patch also removes quite a bit of now unnecessary code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eduardo Valentin [Thu, 3 Jul 2008 09:24:40 +0000 (12:24 +0300)]
ARM: OMAP: McBSP: Add support for mcbsp on mach-omap2
This patch adds support for mach-omap2 based on current
mcbsp platform driver.
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eduardo Valentin [Thu, 3 Jul 2008 09:24:40 +0000 (12:24 +0300)]
ARM: OMAP: McBSP: Add support for mcbsp on mach-omap1
This patch adds support for mach-omap1 based on current
mcbsp platform driver.
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eduardo Valentin [Thu, 3 Jul 2008 09:24:39 +0000 (12:24 +0300)]
ARM: OMAP: McBSP: Prepare for splitting into omap1 and omap2 code
This patch transform mcbsp code to use platform data
from arch/arm/plat-omap/devices.c
It also gets ride of ifdefs on mcbsp.c code.
To do it, a platform data structure was defined.
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eduardo Valentin [Thu, 3 Jul 2008 09:24:39 +0000 (12:24 +0300)]
ARM: OMAP: McBSP: Coding style cleanup on arch/arm/plat-omap/mcbsp.c
This patch fix lots of warnings and errors reported by
scripts/checkpatch.pl on arch/arm/plat-omap/mcbsp.c.
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 3 Jul 2008 09:24:38 +0000 (12:24 +0300)]
ARM: OMAP: SRAM: Split sram24xx.S into sram242x.S and sram243x.S
Split sram24xx.S into sram242x.S and sram243x.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 3 Jul 2008 09:24:38 +0000 (12:24 +0300)]
ARM: OMAP: SRAM: Move omap2 sram-fn.S to sram242x.S
This file will get split between sram242x.S and sram243x.S
in following patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 3 Jul 2008 09:24:38 +0000 (12:24 +0300)]
ARM: OMAP: SRAM: Move sram-fn.S from plat-omap to mach-omap1
This file is omap1 specific.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 3 Jul 2008 09:24:37 +0000 (12:24 +0300)]
ARM: OMAP: DMA: Clean-up code
DMA clean-up, mostly checkpatch.pl fixes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 3 Jul 2008 09:24:36 +0000 (12:24 +0300)]
ARM: OMAP: DMA: Remove __REG access
Remove __REG access in DMA code, use dma_read/write instead:
- dynamically set the omap_dma_base based on the omap type
- omap_read/write becomes dma_read/write
- dma channel registers are read with dma_ch_read/write
Cc: David Brownell <david-b@pacbell.net>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 3 Jul 2008 09:24:31 +0000 (12:24 +0300)]
ARM: OMAP: DMA: Make channels dynamic for multi-boot
Make DMA channels dynamic for multi-boot
Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Thu, 3 Jul 2008 09:24:31 +0000 (12:24 +0300)]
ARM: OMAP: Add OMAP3430 base defines
Add symbolic constants for OMAP3430 base addresses; include that file
in hardware.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Richard Woodruff [Thu, 3 Jul 2008 09:24:30 +0000 (12:24 +0300)]
ARM: OMAP: DMTimer: Optimize by adding load and start
This patch optimizes the timer load and start sequence. By combining the
load and start a needless posted wait can be removed from the system timer
execution path.
* Before patch register writes are taking up .078% @ 500MHz during idle.
Address |total |min |max |avr |count|ratio%
old\process\default_idle|7.369s |0.0us|999.902ms|14.477ms|509. |62.661%
ld\Global\cpu_v7_do_idle|4.265s |0.0us|375.786ms|24.374ms|175. |36.270%
(UNKNOWN)|17.503ms|0.us|531.080us|5.119us|3419. |0.148%
r\omap_dm_timer_set_load|8.135ms|0.0us|79.887us|15.065us|540. |0.069% <--
\vmlinux-old\Global\_end|2.023ms|0.0us|4.000us|0.560us|3613. |0.017%
-old\Global\__raw_readsw|1.962ms|0.0us|108.610us|9.167us|214. |0.016%
old\smc91x\smc_interrupt|1.353ms|0.0us|10.212us|2.348us|576. |0.011%
s/namei\__link_path_walk|1.161ms|0.0us|4.310us|0.762us| 1524. |0.009%
\omap_dm_timer_write_reg|1.085ms|0.0us|126.150us|2.153us|504. |0.009% <--
* After patch timer functions do not show up in top listings for long captures.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Richard Woodruff [Thu, 3 Jul 2008 09:24:30 +0000 (12:24 +0300)]
ARM: OMAP: DMTimer: Use posted mode
This patch adds the use of write posting for the timer. Previously, every
write could lock the requestor for almost 3x32KHz cycles. This patch only
synchronizes before writes and reads instead of after them and it does
it on per register basis. Doing it this way there is some chance to hide
some of the sync latency. It also removes some needless reads when
non-posted mode is there. With out this fix the read/writes take almost
2% CPU load @500MHz just waiting on tick timer registers.
Also define new 34xx only registers.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Thara Gopinath [Thu, 3 Jul 2008 09:24:30 +0000 (12:24 +0300)]
ARM: OMAP: Correcting the gpmc prefetch control register address
Correcting the GPMC_PREFETCH_CONTROL register address
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Nikula [Thu, 3 Jul 2008 09:24:29 +0000 (12:24 +0300)]
ARM: OMAP: DMA: Don't mark channel active in omap_enable_channel_irq
Channel should be marked active only when DMA is really started. Otherwise
just omap_request_dma, omap_dma_link_lch and omap_dma_unlink_lch will cause
incorrect dump_stack().
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Thu, 3 Jul 2008 02:29:16 +0000 (19:29 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: acpiphp: cleanup notify handler on all root bridges
PCI: Limit VPD read/write lengths for Broadcom 5706, 5708, 5709 rev.
PCI: Restrict VPD read permission to root
Linus Torvalds [Thu, 3 Jul 2008 02:26:38 +0000 (19:26 -0700)]
Merge branch 'i2c-fix' of git://aeryn.fluff.org.uk/bjdooks/linux
* 'i2c-fix' of git://aeryn.fluff.org.uk/bjdooks/linux:
I2C: S3C2410: Add MODULE_ALIAS() for s3c2440 device.
I2C: S3C2410: Fixup error codes returned rom a transfer.
I2C: S3C2410: Check ACK on byte transmission
Linus Torvalds [Thu, 3 Jul 2008 02:25:36 +0000 (19:25 -0700)]
Merge branch 'for-2.6.26' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.26' of git://git.kernel.dk/linux-2.6-block:
Properly notify block layer of sync writes
block: Fix the starving writes bug in the anticipatory IO scheduler
Linus Torvalds [Thu, 3 Jul 2008 02:24:48 +0000 (19:24 -0700)]
Merge branch 'release' of git://git./linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] export account_system_vtime
[IA64] Bugfix for system with 32 cpus
Linus Torvalds [Thu, 3 Jul 2008 02:23:52 +0000 (19:23 -0700)]
Merge git://git./linux/kernel/git/mchehab/v4l-dvb
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (8178): uvc: Fix compilation breakage for the other drivers, if uvc is selected
V4L/DVB (8145a): USB Video Class driver
Linus Torvalds [Thu, 3 Jul 2008 02:22:54 +0000 (19:22 -0700)]
Merge git://git./linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: fix /proc/ide/ide?/mate reporting
Revert "BAST: Remove old IDE driver"
Linus Torvalds [Thu, 3 Jul 2008 02:22:25 +0000 (19:22 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5131/1: Annotate platform_secondary_init with trace_hardirqs_off
[ARM] 5117/1: pxafb: fix __devinit/exit annotations
[ARM] Export dma_sync_sg_for_device()
[ARM] 5109/1: Mark rtc sa1100 driver as wakeup source before registering it
[ARM] 5116/1: pxafb: cleanup and fix order of failure handling
[ARM] 5115/1: pxafb: fix ifdef for command line option handling
ARM: OMAP: Correcting the gpmc prefetch control register address
ARM: OMAP: DMA: Don't mark channel active in omap_enable_channel_irq
Alan Cox [Mon, 30 Jun 2008 16:40:08 +0000 (17:40 +0100)]
tty: Fix inverted logic in send_break
Not sure how this came to get inverted but it appears to have been my
mess up.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 3 Jul 2008 02:12:53 +0000 (19:12 -0700)]
Merge branch 'sched-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: fix divide error when trying to configure rt_period to zero
Linus Torvalds [Thu, 3 Jul 2008 02:00:29 +0000 (19:00 -0700)]
Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Fix bad hint about irqs in i2c.h
i2c: Documentation: fix device matching description
Linus Torvalds [Thu, 3 Jul 2008 01:59:45 +0000 (18:59 -0700)]
Merge branch 'core-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: fix hotplug vs rcu race
Linus Torvalds [Thu, 3 Jul 2008 01:58:56 +0000 (18:58 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix NODES_SHIFT Kconfig range
Linus Torvalds [Thu, 3 Jul 2008 01:57:33 +0000 (18:57 -0700)]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] esp: tidy up target reference counting
[SCSI] esp: Fix OOPS in esp_reset_cleanup().
[SCSI] ses: Fix timeout
Linus Torvalds [Thu, 3 Jul 2008 01:55:17 +0000 (18:55 -0700)]
Merge git://git./linux/kernel/git/agk/linux-2.6-dm
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm crypt: use cond_resched
Linus Torvalds [Thu, 3 Jul 2008 01:47:10 +0000 (18:47 -0700)]
Merge branch 'for-2.6.26' of git://neil.brown.name/md
* 'for-2.6.26' of git://neil.brown.name/md:
Fix error paths if md_probe fails.
Don't acknowlege that stripe-expand is complete until it really is.
Ensure interrupted recovery completed properly (v1 metadata plus bitmap)
Linus Torvalds [Thu, 3 Jul 2008 01:45:29 +0000 (18:45 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc/mpc5200: Fix lite5200b suspend/resume
powerpc/legacy_serial: Bail if reg-offset/shift properties are present
powerpc/bootwrapper: update for initrd with simpleImage
Linus Torvalds [Thu, 3 Jul 2008 01:43:16 +0000 (18:43 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (55 commits)
net: fib_rules: fix error code for unsupported families
netdevice: Fix wrong string handle in kernel command line parsing
net: Tyop of sk_filter() comment
netlink: Unneeded local variable
net-sched: fix filter destruction in atm/hfsc qdisc destruction
net-sched: change tcf_destroy_chain() to clear start of filter list
ipv4: fix sysctl documentation of time related values
mac80211: don't accept WEP keys other than WEP40 and WEP104
hostap: fix sparse warnings
hostap: don't report useless WDS frames by default
textsearch: fix Boyer-Moore text search bug
netfilter: nf_conntrack_tcp: fixing to check the lower bound of valid ACK
ipv6 route: Convert rt6_device_match() to use RT6_LOOKUP_F_xxx flags.
netlabel: Fix a problem when dumping the default IPv6 static labels
net/inet_lro: remove setting skb->ip_summed when not LRO-able
inet fragments: fix race between inet_frag_find and inet_frag_secret_rebuild
CONNECTOR: add a proc entry to list connectors
netlink: Fix some doc comments in net/netlink/attr.c
tcp: /proc/net/tcp rto,ato values not scaled properly (v2)
include/linux/netdevice.h: don't export MAX_HEADER to userspace
...
Jesse Barnes [Tue, 1 Jul 2008 19:32:52 +0000 (12:32 -0700)]
DRM/i915: only use tiled blits on 965+
When scheduled swaps occur, we need to blit between front & back
buffers. If the buffers are tiled, we need to set the appropriate
XY_SRC_COPY tile bit, but only on 965 chips, since it will cause
corruption on pre-965 (e.g. 945).
Bug reported by and fix tested by Tomas Janousek <tomi@nomi.cz>.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Tue, 1 Jul 2008 11:55:25 +0000 (13:55 +0200)]
drivers/input/ff-core.c needs <linux/sched.h>
Commit
656acd2bbc4ce7f224de499ee255698701396c48 ("Input: fix locking in
force-feedback core") causes the following regression on m68k:
| linux/drivers/input/ff-core.c: In function 'input_ff_upload':
| linux/drivers/input/ff-core.c:172: error: dereferencing pointer to incomplete type
| linux/drivers/input/ff-core.c: In function 'erase_effect':
| linux/drivers/input/ff-core.c:197: error: dereferencing pointer to incomplete type
| linux/drivers/input/ff-core.c:204: error: dereferencing pointer to incomplete type
| make[4]: *** [drivers/input/ff-core.o] Error 1
As the incomplete type is `struct task_struct', including <linux/sched.h> fixes
it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Mackerras [Thu, 3 Jul 2008 00:05:59 +0000 (10:05 +1000)]
Merge branch 'for-2.6.26' of git://git.secretlab.ca/git/linux-2.6-mpc52xx into merge
Alex Chiang [Wed, 2 Jul 2008 02:02:23 +0000 (20:02 -0600)]
PCI: acpiphp: cleanup notify handler on all root bridges
During the development of the physical PCI slot patch series, Gary Hade
kept on reporting strange oopses due to interactions between pci_slot
and acpiphp.
http://lkml.org/lkml/2007/11/28/319
find_root_bridges() unconditionally installs
handle_hotplug_event_bridge() as an ACPI_SYSTEM_NOTIFY handler for all
root bridges.
However, during module cleanup, remove_bridge() will only remove the
notify handler iff the root bridge had a hot-pluggable slot directly
underneath. That is:
root bridge -> hotplug slot
But, if the topology looks like either of the following:
root bridge -> non-hotplug slot
root bridge -> p2p bridge -> hotplug slot
Then we currently do not remove the notify handler from that root
bridge.
This can cause a kernel oops if we modprobe acpiphp later and it gets
loaded somewhere else in memory. If the root bridge then receives a
hotplug event, it will then attempt to call a stale, non-existent notify
handler and we blow up.
Much thanks goes to Gary Hade for his persistent debugging efforts.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Benjamin Li [Wed, 2 Jul 2008 17:59:04 +0000 (10:59 -0700)]
PCI: Limit VPD read/write lengths for Broadcom 5706, 5708, 5709 rev.
For Broadcom 5706, 5708, 5709 rev. A nics, any read beyond the
VPD end tag will hang the device. This problem was initially
observed when a vpd entry was created in sysfs
('/sys/bus/pci/devices/<id>/vpd'). A read to this sysfs entry
will dump 32k of data. Reading a full 32k will cause an access
beyond the VPD end tag causing the device to hang. Once the device
is hung, the bnx2 driver will not be able to reset the device.
We believe that it is legal to read beyond the end tag and
therefore the solution is to limit the read/write length.
A majority of this patch is from Matthew Wilcox who gave code for
reworking the PCI vpd size information. A PCI quirk added for the
Broadcom NIC's to limit the read/write's.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Mauro Carvalho Chehab [Wed, 2 Jul 2008 14:03:33 +0000 (11:03 -0300)]
V4L/DVB (8178): uvc: Fix compilation breakage for the other drivers, if uvc is selected
UVC makefile defines obj as:
obj-$(CONFIG_USB_VIDEO_CLASS) := uvcvideo.o
Instead of:
obj-$(CONFIG_USB_VIDEO_CLASS) += uvcvideo.o
Due to that, if uvc is selected, all obj-y or obj-m that were added to
compilation were forget. This breaks a proper kernel build.
Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Milan Broz [Wed, 2 Jul 2008 08:34:28 +0000 (09:34 +0100)]
dm crypt: use cond_resched
Add cond_resched() to prevent monopolising CPU when processing large bios.
dm-crypt processes encryption of bios in sector units. If the bio request
is big it can spend a long time in the encryption call.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Tested-by: Yan Li <elliot.li.tech@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Patrick McHardy [Wed, 2 Jul 2008 02:59:37 +0000 (19:59 -0700)]
net: fib_rules: fix error code for unsupported families
The errno code returned must be negative.
Fixes "RTNETLINK answers: Unknown error
18446744073709551519".
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Wed, 2 Jul 2008 02:57:19 +0000 (19:57 -0700)]
netdevice: Fix wrong string handle in kernel command line parsing
v1->v2: Use strlcpy() to ensure s[i].name be null-termination.
1. In netdev_boot_setup_add(), a long name will leak.
ex. : dev=21,0x1234,0x1234,0x2345,eth123456789verylongname.........
2. In netdev_boot_setup_check(), mismatch will happen if s[i].name
is a substring of dev->name.
ex. : dev=...eth1 dev=...eth11
[ With feedback from Ben Hutchings. ]
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Wed, 2 Jul 2008 02:55:40 +0000 (19:55 -0700)]
net: Tyop of sk_filter() comment
Parameter "needlock" no long exists.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Wed, 2 Jul 2008 02:55:09 +0000 (19:55 -0700)]
netlink: Unneeded local variable
We already have a variable, which has the same capability.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 2 Jul 2008 02:53:09 +0000 (19:53 -0700)]
net-sched: fix filter destruction in atm/hfsc qdisc destruction
Filters need to be destroyed before beginning to destroy classes
since the destination class needs to still be alive to unbind the
filter.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 2 Jul 2008 02:52:38 +0000 (19:52 -0700)]
net-sched: change tcf_destroy_chain() to clear start of filter list
Pass double tcf_proto pointers to tcf_destroy_chain() to make it
clear the start of the filter list for more consistency.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Wed, 2 Jul 2008 00:22:48 +0000 (17:22 -0700)]
ipv4: fix sysctl documentation of time related values
These sysctl values are time related and all use the same routine
(proc_dointvec_jiffies) that internally converts from seconds to jiffies.
The code is fine, the documentation is just wrong.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tim Yamin [Tue, 17 Jun 2008 08:33:14 +0000 (09:33 +0100)]
powerpc/mpc5200: Fix lite5200b suspend/resume
Suspend/resume ("echo mem > /sys/power/state") does not work with
vanilla kernels -- the system does not suspend correctly and just
hangs. This patch fixes this so suspend/resume works:
1) of_iomap does not map the whole 0xC000 of the MPC5200 immr so
saving registers does not work.
2) PCI registers need to be saved and restored.
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
John Linn [Tue, 1 Jul 2008 17:52:41 +0000 (10:52 -0700)]
powerpc/legacy_serial: Bail if reg-offset/shift properties are present
The legacy serial driver does not work with an 8250 type UART that is
described in the device tree with the reg-offset and reg-shift
properties. This change makes legacy_serial ignore these devices.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Wolfram Sang [Tue, 1 Jul 2008 20:38:18 +0000 (22:38 +0200)]
i2c: Fix bad hint about irqs in i2c.h
i2c.h mentions -1 as a not-issued irq. This false hint was taken by
of_i2c and caused crashes. Don't give any advice as 'no irq' is not
consistent across all architectures yet and it is not needed internally
by the i2c-core.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Ben Dooks [Tue, 1 Jul 2008 20:38:18 +0000 (22:38 +0200)]
i2c: Documentation: fix device matching description
The matching process described for new style clients in
Documentation/i2c/writing-clients is classed as out-of-date
as it requires the presence of an .id_table entry in the
driver's i2c_driver entry.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
John Linn [Tue, 1 Jul 2008 20:17:18 +0000 (14:17 -0600)]
powerpc/bootwrapper: update for initrd with simpleImage
This change to the makefile corrects the build of a simpleImage with initrd.
Signed-off-by: John Linn <john.linn@xilinx>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Ben Hutchings [Tue, 1 Jul 2008 16:18:17 +0000 (17:18 +0100)]
PCI: Restrict VPD read permission to root
Some PCI devices will lock up if we attempt to read from VPD addresses
beyond some device-dependent limit. Until we can identify these
devices and adjust the file size accordingly, only let root read VPD
through sysfs to prevent a DoS by normal users.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Ben Dooks [Tue, 1 Jul 2008 10:59:43 +0000 (11:59 +0100)]
I2C: S3C2410: Add MODULE_ALIAS() for s3c2440 device.
Add a MODULE_ALIAS() statement for the i2c-s3c2410 controller
to ensure that it can be autoloaded on the S3C2440 systems that
we support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ben Dooks [Tue, 1 Jul 2008 10:59:42 +0000 (11:59 +0100)]
I2C: S3C2410: Fixup error codes returned rom a transfer.
The driver should be returning -ENXIO for transfers that do not
pass the initial address byte stage.
Note, also small tidyups to the driver comments in the area.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ben Dooks [Tue, 1 Jul 2008 10:59:41 +0000 (11:59 +0100)]
I2C: S3C2410: Check ACK on byte transmission
We should check for the reception of an ACK after transmitting each
data byte. The address send has been correctly checking this, but the
data write byte state should have also been checking for these failures.
As part of the same fix, we remove the ACK checking from the receive
path where it should not have been checking for an ACK which our hardware
was sending.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Gautham R Shenoy [Fri, 27 Jun 2008 04:47:38 +0000 (10:17 +0530)]
rcu: fix hotplug vs rcu race
Dhaval Giani reported this warning during cpu hotplug stress-tests:
| On running kernel compiles in parallel with cpu hotplug:
|
| WARNING: at arch/x86/kernel/smp.c:118
| native_smp_send_reschedule+0x21/0x36()
| Modules linked in:
| Pid: 27483, comm: cc1 Not tainted 2.6.26-rc7 #1
| [...]
| [<
c0110355>] native_smp_send_reschedule+0x21/0x36
| [<
c014fe8f>] force_quiescent_state+0x47/0x57
| [<
c014fef0>] call_rcu+0x51/0x6d
| [<
c01713b3>] __fput+0x130/0x158
| [<
c0171231>] fput+0x17/0x19
| [<
c016fd99>] filp_close+0x4d/0x57
| [<
c016fdff>] sys_close+0x5c/0x97
IMHO the warning is a spurious one.
cpu_online_map is updated by the _cpu_down() using stop_machine_run().
Since force_quiescent_state is invoked from irqs disabled section,
stop_machine_run() won't be executing while a cpu is executing
force_quiescent_state(). Hence the cpu_online_map is stable while we're
in the irq disabled section.
However, a cpu might have been offlined _just_ before we disabled irqs
while entering force_quiescent_state(). And rcu subsystem might not yet
have handled the CPU_DEAD notification, leading to the offlined cpu's
bit being set in the rcp->cpumask.
Hence cpumask = (rcp->cpumask & cpu_online_map) to prevent sending
smp_reschedule() to an offlined CPU.
Here's the timeline:
CPU_A CPU_B
--------------------------------------------------------------
cpu_down(): .
. .
. .
stop_machine(): /* disables preemption, .
* and irqs */ .
. .
. .
take_cpu_down(); .
. .
. .
. .
cpu_disable(); /*this removes cpu .
*from cpu_online_map .
*/ .
. .
. .
restart_machine(); /* enables irqs */ .
------WINDOW DURING WHICH rcp->cpumask is stale ---------------
. call_rcu();
. /* disables irqs here */
. .force_quiescent_state();
.CPU_DEAD: .for_each_cpu(rcp->cpumask)
. . smp_send_reschedule();
. .
. . WARN_ON() for offlined CPU!
.
.
.
rcu_cpu_notify:
.
-------- WINDOW ENDS ------------------------------------------
rcu_offline_cpu() /* Which calls cpu_quiet()
* which removes
* cpu from rcp->cpumask.
*/
If a new batch was started just before calling stop_machine_run(), the
"tobe-offlined" cpu is still present in rcp-cpumask.
During a cpu-offline, from take_cpu_down(), we queue an rt-prio idle
task as the next task to be picked by the scheduler. We also call
cpu_disable() which will disable any further interrupts and remove the
cpu's bit from the cpu_online_map.
Once the stop_machine_run() successfully calls take_cpu_down(), it calls
schedule(). That's the last time a schedule is called on the offlined
cpu, and hence the last time when rdp->passed_quiesc will be set to 1
through rcu_qsctr_inc().
But the cpu_quiet() will be on this cpu will be called only when the
next RCU_SOFTIRQ occurs on this CPU. So at this time, the offlined CPU
is still set in rcp->cpumask.
Now coming back to the idle_task which truely offlines the CPU, it does
check for a pending RCU and raises the softirq, since it will find
rdp->passed_quiesc to be 0 in this case. However, since the cpu is
offline I am not sure if the softirq will trigger on the CPU.
Even if it doesn't the rcu_offline_cpu() will find that rcp->completed
is not the same as rcp->cur, which means that our cpu could be holding
up the grace period progression. Hence we call cpu_quiet() and move
ahead.
But because of the window explained in the timeline, we could still have
a call_rcu() before the RCU subsystem executes it's CPU_DEAD
notification, and we send smp_send_reschedule() to offlined cpu while
trying to force the quiescent states. The appended patch adds comments
and prevents checking for offlined cpu everytime.
cpu_online_map is updated by the _cpu_down() using stop_machine_run().
Since force_quiescent_state is invoked from irqs disabled section,
stop_machine_run() won't be executing while a cpu is executing
force_quiescent_state(). Hence the cpu_online_map is stable while we're
in the irq disabled section.
Reported-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Cc: laijs@cn.fujitsu.com
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Rusty Russel <rusty@rustcorp.com.au>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jens Axboe [Tue, 1 Jul 2008 07:07:34 +0000 (09:07 +0200)]
Properly notify block layer of sync writes
fsync_buffers_list() and sync_dirty_buffer() both issue async writes and
then immediately wait on them. Conceptually, that makes them sync writes
and we should treat them as such so that the IO schedulers can handle
them appropriately.
This patch fixes a write starvation issue that Lin Ming reported, where
xx is stuck for more than 2 minutes because of a large number of
synchronous IO in the system:
INFO: task kjournald:20558 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this
message.
kjournald D
ffff810010820978 6712 20558 2
ffff81022ddb1d10 0000000000000046 ffff81022e7baa10 ffffffff803ba6f2
ffff81022ecd0000 ffff8101e6dc9160 ffff81022ecd0348 000000008048b6cb
0000000000000086 ffff81022c4e8d30 0000000000000000 ffffffff80247537
Call Trace:
[<
ffffffff803ba6f2>] kobject_get+0x12/0x17
[<
ffffffff80247537>] getnstimeofday+0x2f/0x83
[<
ffffffff8029c1ac>] sync_buffer+0x0/0x3f
[<
ffffffff8066d195>] io_schedule+0x5d/0x9f
[<
ffffffff8029c1e7>] sync_buffer+0x3b/0x3f
[<
ffffffff8066d3f0>] __wait_on_bit+0x40/0x6f
[<
ffffffff8029c1ac>] sync_buffer+0x0/0x3f
[<
ffffffff8066d48b>] out_of_line_wait_on_bit+0x6c/0x78
[<
ffffffff80243909>] wake_bit_function+0x0/0x23
[<
ffffffff8029e3ad>] sync_dirty_buffer+0x98/0xcb
[<
ffffffff8030056b>] journal_commit_transaction+0x97d/0xcb6
[<
ffffffff8023a676>] lock_timer_base+0x26/0x4b
[<
ffffffff8030300a>] kjournald+0xc1/0x1fb
[<
ffffffff802438db>] autoremove_wake_function+0x0/0x2e
[<
ffffffff80302f49>] kjournald+0x0/0x1fb
[<
ffffffff802437bb>] kthread+0x47/0x74
[<
ffffffff8022de51>] schedule_tail+0x28/0x5d
[<
ffffffff8020cac8>] child_rip+0xa/0x12
[<
ffffffff80243774>] kthread+0x0/0x74
[<
ffffffff8020cabe>] child_rip+0x0/0x12
Lin Ming confirms that this patch fixes the issue. I've run tests with
it for the past week and no ill effects have been observed, so I'm
proposing it for inclusion into 2.6.26.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Divyesh Shah [Mon, 16 Jun 2008 16:37:08 +0000 (18:37 +0200)]
block: Fix the starving writes bug in the anticipatory IO scheduler
AS scheduler alternates between issuing read and write batches. It does
the batch switch only after all requests from the previous batch are
completed.
When switching to a write batch, if there is an on-going read request,
it waits for its completion and indicates its intention of switching by
setting ad->changed_batch and the new direction but does not update the
batch_expire_time for the new write batch which it does in the case of
no previous pending requests.
On completion of the read request, it sees that we were waiting for the
switch and schedules work for kblockd right away and resets the
ad->changed_data flag.
Now when kblockd enters dispatch_request where it is expected to pick
up a write request, it in turn ends the write batch because the
batch_expire_timer was not updated and shows the expire timestamp for
the previous batch.
This results in the write starvation for all the cases where there is
the intention for switching to a write batch, but there is a previous
in-flight read request and the batch gets reverted to a read_batch
right away.
This also holds true in the reverse case (switching from a write batch
to a read batch with an in-flight write request).
I've checked that this bug exists on 2.6.11, 2.6.18, 2.6.24 and
linux-2.6-block git HEAD. I've tested the fix on x86 platforms with
SCSI drives where the driver asks for the next request while a current
request is in-flight.
This patch is based off linux-2.6-block git HEAD.
Bug reproduction:
A simple scenario which reproduces this bug is:
- dd if=/dev/hda3 of=/dev/null &
- lilo
The lilo takes forever to complete.
This can also be reproduced fairly easily with the earlier dd and
another test
program doing msync().
The example test program below should print out a message after every
iteration
but it simply hangs forever. With this bugfix it makes forward progress.
====
Example test program using msync() (thanks to suleiman AT google DOT
com)
inline uint64_t
rdtsc(void)
{
int64_t tsc;
__asm __volatile("rdtsc" : "=A" (tsc));
return (tsc);
}
int
main(int argc, char **argv)
{
struct stat st;
uint64_t e, s, t;
char *p, q;
long i;
int fd;
if (argc < 2) {
printf("Usage: %s <file>\n", argv[0]);
return (1);
}
if ((fd = open(argv[1], O_RDWR | O_NOATIME)) < 0)
err(1, "open");
if (fstat(fd, &st) < 0)
err(1, "fstat");
p = mmap(NULL, st.st_size, PROT_READ | PROT_WRITE,
MAP_SHARED, fd, 0);
t = 0;
for (i = 0; i < 1000; i++) {
*p = 0;
msync(p, 4096, MS_SYNC);
s = rdtsc();
*p = 0;
__asm __volatile(""::: "memory");
e = rdtsc();
if (argc > 2)
printf("%d: %lld cycles %jd %jd\n",
i, e - s, (intmax_t)s, (intmax_t)e);
t += e - s;
}
printf("average time: %lld cycles\n", t / 1000);
return (0);
}
Cc: <stable@kernel.org>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Thomas Gleixner [Tue, 1 Jul 2008 06:56:32 +0000 (08:56 +0200)]
x86: fix NODES_SHIFT Kconfig range
commit
4323838215184f5a2f081e0d17b8d60731b03164
x86: change size of node ids from u8 to s16
set the range for NODES_SHIFT to 1..15.
The possible range is 1..9
Fixes Bugzilla #10726
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Raistlin [Thu, 26 Jun 2008 16:54:09 +0000 (18:54 +0200)]
sched: fix divide error when trying to configure rt_period to zero
Here it is another little Oops we found while configuring invalid values
via cgroups:
echo 0 > /dev/cgroups/0/cpu.rt_period_us
or
echo
4294967296 > /dev/cgroups/0/cpu.rt_period_us
[ 205.509825] divide error: 0000 [#1]
[ 205.510151] Modules linked in:
[ 205.510151]
[ 205.510151] Pid: 2339, comm: bash Not tainted (2.6.26-rc8 #33)
[ 205.510151] EIP: 0060:[<
c030c6ef>] EFLAGS:
00000293 CPU: 0
[ 205.510151] EIP is at div64_u64+0x5f/0x70
[ 205.510151] EAX:
0000389f EBX:
00000000 ECX:
00000000 EDX:
00000000
[ 205.510151] ESI:
d9800000 EDI:
00000000 EBP:
c6cede60 ESP:
c6cede50
[ 205.510151] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
[ 205.510151] Process bash (pid: 2339, ti=
c6cec000 task=
c79be370 task.ti=
c6cec000)
[ 205.510151] Stack:
d9800000 0000389f c05971a0 d9800000 c6cedeb4 c0214dbd 00000000 00000000
[ 205.510151]
c6cede88 c0242bd8 c05377c0 c7a41b40 00000000 00000000 00000000 c05971a0
[ 205.510151]
c780ed20 c7508494 c7a41b40 00000000 00000002 c6cedebc c05971a0 ffffffea
[ 205.510151] Call Trace:
[ 205.510151] [<
c0214dbd>] ? __rt_schedulable+0x1cd/0x240
[ 205.510151] [<
c0242bd8>] ? cgroup_file_open+0x18/0xe0
[ 205.510151] [<
c0214fe4>] ? tg_set_bandwidth+0xa4/0xf0
[ 205.510151] [<
c0215066>] ? sched_group_set_rt_period+0x36/0x50
[ 205.510151] [<
c021508e>] ? cpu_rt_period_write_uint+0xe/0x10
[ 205.510151] [<
c0242dc5>] ? cgroup_file_write+0x125/0x160
[ 205.510151] [<
c0232c15>] ? hrtimer_interrupt+0x155/0x190
[ 205.510151] [<
c02f047f>] ? security_file_permission+0xf/0x20
[ 205.510151] [<
c0277ad8>] ? rw_verify_area+0x48/0xc0
[ 205.510151] [<
c0283744>] ? dupfd+0x104/0x130
[ 205.510151] [<
c027838c>] ? vfs_write+0x9c/0x160
[ 205.510151] [<
c0242ca0>] ? cgroup_file_write+0x0/0x160
[ 205.510151] [<
c027850d>] ? sys_write+0x3d/0x70
[ 205.510151] [<
c0203019>] ? sysenter_past_esp+0x6a/0x91
[ 205.510151] =======================
[ 205.510151] Code: 0f 45 de 31 f6 0f ad d0 d3 ea f6 c1 20 0f 45 c2 0f 45 d6 89 45 f0 89 55 f4 8b 55 f4 31 c9 8b 45 f0 39 d3 89 c6 77 08 89 d0 31 d2 <f7> f3 89 c1 83 c4 08 89 f0 f7 f3 89 ca 5b 5e 5d c3 55 89 e5 56
[ 205.510151] EIP: [<
c030c6ef>] div64_u64+0x5f/0x70 SS:ESP 0068:
c6cede50
The attached patch solves the issue for me.
I'm checking as soon as possible for the period not being zero since, if
it is, going ahead is useless. This way we also save a mutex_lock() and
a read_lock() wrt doing it inside tg_set_bandwidth() or
__rt_schedulable().
Signed-off-by: Dario Faggioli <raistlin@linux.it>
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Doug Chapman [Mon, 30 Jun 2008 22:06:48 +0000 (15:06 -0700)]
[IA64] export account_system_vtime
The symbol account_system_vtime is used by the kvm module but
not exported. This breaks building with CONFIG_VIRT_CPU_ACCOUNTING
and CONFIG_KVM=m.
Signed-off-by: Doug Chapman <doug.chapman@hp.com>
Acked-by: Hidetosho Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Tony Luck [Mon, 30 Jun 2008 22:03:14 +0000 (15:03 -0700)]
[IA64] Bugfix for system with 32 cpus
On a system where there are no hot pluggable cpus "additional_cpus"
is still set to -1 at the point where we call per_cpu_scan_finalize().
If we didn't find an SRAT table and so pick the default "32" for the
number of cpus, when we get to:
high_cpu = min(high_cpu + reserve_cpus, NR_CPUS);
we will end up initializing for just 31 cpus ... and so we will
die horribly when bringing up cpu#32.
Problem introduced by:
2c6e6db41f01b6b4eb98809350827c9678996698
"Minimize per_cpu reservations."
Acked-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Laurent Pinchart [Mon, 30 Jun 2008 18:04:50 +0000 (15:04 -0300)]
V4L/DVB (8145a): USB Video Class driver
This driver supports video input devices compliant with the USB Video Class
specification. This means lots of currently manufactured webcams, and probably
most of the future ones.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
David S. Miller [Mon, 30 Jun 2008 20:18:53 +0000 (13:18 -0700)]
Merge branch 'master' of /linux/kernel/git/linville/wireless-2.6
Emmanuel Grumbach [Fri, 27 Jun 2008 23:50:13 +0000 (02:50 +0300)]
mac80211: don't accept WEP keys other than WEP40 and WEP104
This patch makes mac80211 refuse a WEP key whose length is not WEP40 nor
WEP104.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin [Fri, 27 Jun 2008 20:19:58 +0000 (16:19 -0400)]
hostap: fix sparse warnings
Rewrite AID calculation in handle_pspoll() to avoid truncating bits.
Make hostap_80211_header_parse() static, don't export it. Avoid
shadowing variables.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin [Fri, 27 Jun 2008 20:19:52 +0000 (16:19 -0400)]
hostap: don't report useless WDS frames by default
DEBUG_EXTRA is reported to the kernel log by default, but DEBUG_EXTRA2
is not. Unrelated WDS frames pollute the log unnecessarily.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joonwoo Park [Mon, 30 Jun 2008 19:42:23 +0000 (12:42 -0700)]
textsearch: fix Boyer-Moore text search bug
The current logic has a bug which cannot find matching pattern, if the
pattern is matched from the first character of target string.
for example:
pattern=abc, string=abcdefg
pattern=a, string=abcdefg
Searching algorithm should return 0 for those things.
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jozsef Kadlecsik [Mon, 30 Jun 2008 19:41:30 +0000 (12:41 -0700)]
netfilter: nf_conntrack_tcp: fixing to check the lower bound of valid ACK
Lost connections was reported by Thomas Bätzler (running 2.6.25 kernel) on
the netfilter mailing list (see the thread "Weird nat/conntrack Problem
with PASV FTP upload"). He provided tcpdump recordings which helped to
find a long lingering bug in conntrack.
In TCP connection tracking, checking the lower bound of valid ACK could
lead to mark valid packets as INVALID because:
- We have got a "higher or equal" inequality, but the test checked
the "higher" condition only; fixed.
- If the packet contains a SACK option, it could occur that the ACK
value was before the left edge of our (S)ACK "window": if a previous
packet from the other party intersected the right edge of the window
of the receiver, we could move forward the window parameters beyond
accepting a valid ack. Therefore in this patch we check the rightmost
SACK edge instead of the ACK value in the lower bound of valid (S)ACK
test.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bartlomiej Zolnierkiewicz [Mon, 30 Jun 2008 18:14:45 +0000 (20:14 +0200)]
ide: fix /proc/ide/ide?/mate reporting
Now that we support warm-plug mate port will be registered
even if there are no devices attached to it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Mon, 30 Jun 2008 18:13:31 +0000 (20:13 +0200)]
Revert "BAST: Remove old IDE driver"
This reverts commit
ac1623625c5818bbdf5c68973098ba386ba7a004.
It was premature to remove it now, we will do it post-2.6.26.
Thanks to Russell King for noticing the issue.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Catalin Marinas [Fri, 27 Jun 2008 14:15:12 +0000 (15:15 +0100)]
[ARM] 5131/1: Annotate platform_secondary_init with trace_hardirqs_off
This patch annotates the platform_secondary_init function in
arch/arm/mach-realview/platsmp.c with trace_hardirqs_off to avoid a
warning when LOCKDEP and TRACE_IRQFLAGS are enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Mon, 30 Jun 2008 15:58:09 +0000 (08:58 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: fix locking in force-feedback core
Input: add KEY_MEDIA_REPEAT definition
Linus Torvalds [Mon, 30 Jun 2008 15:57:43 +0000 (08:57 -0700)]
Merge branch 'core-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
debugobjects: fix lockdep warning
Linus Torvalds [Mon, 30 Jun 2008 15:57:19 +0000 (08:57 -0700)]
Merge branch 'sched-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: fix cpu hotplug
Linus Torvalds [Mon, 30 Jun 2008 15:56:57 +0000 (08:56 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ptrace GET/SET FPXREGS broken
x86: fix cpu hotplug crash
x86: section/warning fixes
x86: shift bits the right way in native_read_tscp
Dmitry Torokhov [Thu, 26 Jun 2008 15:30:02 +0000 (11:30 -0400)]
Input: fix locking in force-feedback core
The newly added event_lock spinlock in the input core disallows sleeping
and therefore using mutexes in event handlers. Convert force-feedback
core to rely on event_lock instead of mutex to protect slots allocated
for fore-feedback effects. The original mutex is still used to serialize
uploading and erasing of effects.
Reported-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bastien Nocera [Thu, 26 Jun 2008 13:13:48 +0000 (09:13 -0400)]
Input: add KEY_MEDIA_REPEAT definition
This patch adds the Repeat key to the input layer. The usage
in the HUT is 0xBC (listed under "15.7 Transport Controls").
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
TAKADA Yoshihito [Mon, 30 Jun 2008 04:44:45 +0000 (13:44 +0900)]
ptrace GET/SET FPXREGS broken
When I update kernel 2.6.25 from 2.6.24, gdb does not work.
On 2.6.25, ptrace(PTRACE_GETFPXREGS, ...) returns ENODEV.
But 2.6.24 kernel's ptrace() returns EIO.
It is issue of compatibility.
I attached test program as pt.c and patch for fix it.
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <signal.h>
#include <errno.h>
#include <sys/ptrace.h>
#include <sys/types.h>
struct user_fxsr_struct {
unsigned short cwd;
unsigned short swd;
unsigned short twd;
unsigned short fop;
long fip;
long fcs;
long foo;
long fos;
long mxcsr;
long reserved;
long st_space[32]; /* 8*16 bytes for each FP-reg = 128 bytes */
long xmm_space[32]; /* 8*16 bytes for each XMM-reg = 128 bytes */
long padding[56];
};
int main(void)
{
pid_t pid;
pid = fork();
switch(pid){
case -1:/* error */
break;
case 0:/* child */
child();
break;
default:
parent(pid);
break;
}
return 0;
}
int child(void)
{
ptrace(PTRACE_TRACEME);
kill(getpid(), SIGSTOP);
sleep(10);
return 0;
}
int parent(pid_t pid)
{
int ret;
struct user_fxsr_struct fpxregs;
ret = ptrace(PTRACE_GETFPXREGS, pid, 0, &fpxregs);
if(ret < 0){
printf("%d: %s.\n", errno, strerror(errno));
}
kill(pid, SIGCONT);
wait(pid);
return 0;
}
/* in the kerel, at kernel/i387.c get_fpxregs() */
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Zhang, Yanmin [Tue, 24 Jun 2008 08:06:23 +0000 (16:06 +0800)]
x86: fix cpu hotplug crash
Vegard Nossum reported crashes during cpu hotplug tests:
http://marc.info/?l=linux-kernel&m=
121413950227884&w=4
In function _cpu_up, the panic happens when calling
__raw_notifier_call_chain at the second time. Kernel doesn't panic when
calling it at the first time. If just say because of nr_cpu_ids, that's
not right.
By checking the source code, I found that function do_boot_cpu is the culprit.
Consider below call chain:
_cpu_up=>__cpu_up=>smp_ops.cpu_up=>native_cpu_up=>do_boot_cpu.
So do_boot_cpu is called in the end. In do_boot_cpu, if
boot_error==true, cpu_clear(cpu, cpu_possible_map) is executed. So later
on, when _cpu_up calls __raw_notifier_call_chain at the second time to
report CPU_UP_CANCELED, because this cpu is already cleared from
cpu_possible_map, get_cpu_sysdev returns NULL.
Many resources are related to cpu_possible_map, so it's better not to
change it.
Below patch against 2.6.26-rc7 fixes it by removing the bit clearing in
cpu_possible_map.
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Tested-by: Vegard Nossum <vegard.nossum@gmail.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Sun, 29 Jun 2008 19:22:55 +0000 (12:22 -0700)]
Merge git://git./linux/kernel/git/mchehab/v4l-dvb
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (42 commits)
V4L/DVB (8108): Fix open/close race in saa7134
V4L/DVB (8100): V4L/vivi: fix possible memory leak in vivi_fillbuff
V4L/DVB (8097): xc5000: check device hardware state to determine if firmware download is needed
V4L/DVB (8096): au8522: prevent false-positive lock status
V4L/DVB (8092): videodev: simplify and fix standard enumeration
V4L/DVB (8075): stv0299: Uncorrected block count and bit error rate fixed
V4L/DVB (8074): av7110: OSD transfers should not be interrupted
V4L/DVB (8073): av7110: Catch another type of ARM crash
V4L/DVB (8071): tda10023: Fix possible kernel oops during initialisation
V4L/DVB (8069): cx18: Fix S-Video and Compsite inputs for the Yuan MPC718 and enable card entry
V4L/DVB (8068): cx18: Add I2C slave reset via GPIO upon initialization
V4L/DVB (8067): cx18: Fix firmware load for case when digital capture happens first
V4L/DVB (8066): cx18: Fix audio mux input definitions for HVR-1600 Line In 2 and FM radio
V4L/DVB (8063): cx18: Fix unintended auto configurations in cx18-av-core
V4L/DVB (8061): cx18: only select tuner / frontend modules if !DVB_FE_CUSTOMISE
V4L/DVB (8048): saa7134: Fix entries for Avermedia A16d and Avermedia E506
V4L/DVB (8044): au8522: tuning optimizations
V4L/DVB (8043): au0828: add support for additional USB device id's
V4L/DVB (8042): DVB-USB UMT-010 channel scan oops
V4L/DVB (8040): soc-camera: remove soc_camera_host_class class
...
Linus Torvalds [Sun, 29 Jun 2008 19:22:30 +0000 (12:22 -0700)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
dock: bay: Don't call acpi_walk_namespace() when ACPI is disabled.
ACPI: don't walk tables if ACPI was disabled
thermal: Create CONFIG_THERMAL_HWMON=n
Linus Torvalds [Sun, 29 Jun 2008 19:21:02 +0000 (12:21 -0700)]
Merge git://git./linux/kernel/git/sam/kbuild-fixes
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
kbuild: fix a.out.h export to userspace with O= build.
Linus Torvalds [Sun, 29 Jun 2008 19:20:11 +0000 (12:20 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: fw-sbp2: fix parsing of logical unit directories
Linus Torvalds [Sun, 29 Jun 2008 19:19:02 +0000 (12:19 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-udf-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6:
udf: Fix regression in UDF anchor block detection
Eduard - Gabriel Munteanu [Thu, 26 Jun 2008 07:54:34 +0000 (10:54 +0300)]
Fix and clean top .gitignore
Removed vmlinux* rule because it matches too many useful files, replacing
it with rules matching filetype by filename (e.g. *.gz). Also unignored
.mailmap from the top directory. Added a comment telling the user how to
check for tracked files being ignored.
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 29 Jun 2008 19:16:07 +0000 (12:16 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin arch: fix up section mismatch warning
Blackfin arch: fix bug - kernel boot fails when Spinlock and rw-lock debugging enabled
Linus Torvalds [Sun, 29 Jun 2008 19:15:10 +0000 (12:15 -0700)]
Merge branch 'audit.b52' of git://git./linux/kernel/git/viro/audit-current
* 'audit.b52' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] remove useless argument type in audit_filter_user()
[PATCH] audit: fix kernel-doc parameter notation
[PATCH] kernel/audit.c: nlh->nlmsg_type is gotten more than once
Linus Torvalds [Sun, 29 Jun 2008 19:14:37 +0000 (12:14 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
[patch 2/3] vfs: dcache cleanups
[patch 1/3] vfs: dcache sparse fixes
[patch 3/3] vfs: make d_path() consistent across mount operations
[patch 4/4] flock: remove unused fields from file_lock_operations
[patch 3/4] vfs: fix ERR_PTR abuse in generic_readlink
[patch 2/4] fs: make struct file arg to d_path const
[patch 1/4] vfs: path_{get,put}() cleanups
[patch for 2.6.26 4/4] vfs: utimensat(): fix write access check for futimens()
[patch for 2.6.26 3/4] vfs: utimensat(): fix error checking for {UTIME_NOW,UTIME_OMIT} case
[patch for 2.6.26 1/4] vfs: utimensat(): ignore tv_sec if tv_nsec == UTIME_OMIT or UTIME_NOW
[patch for 2.6.26 2/4] vfs: utimensat(): be consistent with utime() for immutable and append-only files
[PATCH] fix cgroup-inflicted breakage in block_dev.c
Dmitry Adamushko [Sat, 28 Jun 2008 22:16:56 +0000 (00:16 +0200)]
sched: fix cpu hotplug
the CPU hotplug problems (crashes under high-volume unplug+replug
tests) seem to be related to migrate_dead_tasks().
Firstly I added traces to see all tasks being migrated with
migrate_live_tasks() and migrate_dead_tasks(). On my setup the problem
pops up (the one with "se == NULL" in the loop of
pick_next_task_fair()) shortly after the traces indicate that some has
been migrated with migrate_dead_tasks()). btw., I can reproduce it
much faster now with just a plain cpu down/up loop.
[disclaimer] Well, unless I'm really missing something important in
this late hour [/desclaimer] pick_next_task() is not something
appropriate for migrate_dead_tasks() :-)
the following change seems to eliminate the problem on my setup
(although, I kept it running only for a few minutes to get a few
messages indicating migrate_dead_tasks() does move tasks and the
system is still ok)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
YOSHIFUJI Hideaki [Sat, 28 Jun 2008 03:14:54 +0000 (20:14 -0700)]
ipv6 route: Convert rt6_device_match() to use RT6_LOOKUP_F_xxx flags.
The commit
77d16f450ae0452d7d4b009f78debb1294fb435c ("[IPV6] ROUTE:
Unify RT6_F_xxx and RT6_SELECT_F_xxx flags") intended to pass various
routing lookup hints around RT6_LOOKUP_F_xxx flags, but conversion was
missing for rt6_device_match().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>