OSDN Git Service
Jay Fenlason [Fri, 16 May 2008 15:15:23 +0000 (11:15 -0400)]
firewire: prevent userspace from accessing shut down devices
If userspace ignores the POLLERR bit from poll(), and only attempts to
read() the device when POLLIN is set, it can still make ioctl() calls on
a device that has been removed from the system. The node_id and
generation returned by GET_INFO will be outdated, but INITIATE_BUS_RESET
would still cause a bus reset, and GET_CYCLE_TIMER will return data.
And if you guess the correct generation to use, you can send requests to
a different device on the bus, and get responses back.
This patch prevents open, ioctl, compat_ioctl, and mmap against shutdown
devices.
Signed-off-by: Jay Fenlason <fenlason@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 4 May 2008 14:54:14 +0000 (16:54 +0200)]
ieee1394: sbp2: use correct size of command descriptor block
Boaz Harrosh wrote:
> cmd->cmd_len is now guarantied to be set properly at all cases.
> And some commands you want to support will not be set correctly
> by COMMAND_SIZE().
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Linus Torvalds [Tue, 20 May 2008 15:16:25 +0000 (08:16 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: remove CVS keywords
HID: Add iMON LCDs to blacklist
HID: add Microchip PICKit 1 and PICkit 2 to blacklist
HID: split Numlock emulation quirk from HID_QUIRK_APPLE_HAS_FN.
Linus Torvalds [Tue, 20 May 2008 15:15:34 +0000 (08:15 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Update defconfigs for desktop/server systems
[POWERPC] Fix mpc8377_mds.dts DMA nodes to match spec
[POWERPC] Update arch/powerpc/boot/.gitignore
[POWERPC] Remove generated files on make clean
[POWERPC] powerpc/mm/hash_low_32.S: Remove CVS keyword
[POWERPC] Update Cell MAINTAINERS entry, add spufs entry
lmb: Fix compile warning
Linus Torvalds [Tue, 20 May 2008 15:15:18 +0000 (08:15 -0700)]
Merge git://git./linux/kernel/git/steve/gfs2-2.6-fixes
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
[GFS2] Prefer strlcpy() over snprintf()
[GFS2] Fix cast from unsigned int to s64
[GFS2] filesystem consistency error from do_strip
Hugh Dickins [Tue, 20 May 2008 12:59:47 +0000 (13:59 +0100)]
x86: strengthen 64-bit p?d_bad()
The x86_64 pgd_bad(), pud_bad(), pmd_bad() inlines have differed from
their x86_32 counterparts in a couple of ways: they've been unnecessarily
weak (e.g. letting 0 or 1 count as good), and were typed as unsigned long.
Strengthen them and return int.
The PAE pmd_bad was too weak before, allowing any junk in the upper half;
but got strengthened by the patch correcting its ~PAGE_MASK to ~PTE_MASK.
The PAE pud_bad already said ~PTE_MASK; and since it folds into pgd_bad,
and we don't set the protection bits at that level, it'll do as is.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeremy Fitzhardinge [Tue, 20 May 2008 07:26:24 +0000 (08:26 +0100)]
xen: use PTE_MASK in pte_mfn()
Use PTE_MASK to extract mfn from pte.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Tested-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeremy Fitzhardinge [Tue, 20 May 2008 07:26:23 +0000 (08:26 +0100)]
x86: use PTE_MASK rather than ad-hoc mask
Use ~PTE_MASK to extract the non-pfn parts of the pte (ie, the pte
flags), rather than constructing an ad-hoc mask.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Tested-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeremy Fitzhardinge [Tue, 20 May 2008 07:26:22 +0000 (08:26 +0100)]
x86: clarify use of _PAGE_CHG_MASK
_PAGE_CHG_MASK is defined as the set of bits not updated by
pte_modify(); specifically, the pfn itself, and the Accessed and Dirty
bits (which are updated by hardware).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Tested-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeremy Fitzhardinge [Tue, 20 May 2008 07:26:21 +0000 (08:26 +0100)]
x86: use PTE_MASK in pgtable_32.h
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeremy Fitzhardinge [Tue, 20 May 2008 07:26:20 +0000 (08:26 +0100)]
x86: use PTE_MASK in 32-bit PAE
Use PTE_MASK in 3-level pagetables (ie, 32-bit PAE).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Tested-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeremy Fitzhardinge [Tue, 20 May 2008 07:26:19 +0000 (08:26 +0100)]
x86: rearrange __(VIRTUAL|PHYSICAL)_MASK
Put the definitions of __(VIRTUAL|PHYSICAL)_MASK before their uses.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Tested-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeremy Fitzhardinge [Tue, 20 May 2008 07:26:18 +0000 (08:26 +0100)]
x86: fix warning on 32-bit non-PAE
Fix the warning:
include2/asm/pgtable.h: In function `pte_modify':
include2/asm/pgtable.h:290: warning: left shift count >= width of type
On 32-bit PAE the virtual and physical addresses are both 32-bits,
so it ends up evaluating 1<<32. Do the shift as a 64-bit shift then
cast to the appropriate size. This should all be done at compile time,
and so have no effect on generated code.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Tested-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeremy Fitzhardinge [Tue, 20 May 2008 07:26:17 +0000 (08:26 +0100)]
x86: define PTE_MASK in a universally useful way
Define PTE_MASK so that it contains a meaningful value for all x86
pagetable configurations. Previously it was defined as a "long" which
means that it was too short to cover a 32-bit PAE pte entry.
It is now defined as a pteval_t, which is an integer type long enough
to contain a full pte (or pmd, pud, pgd).
This fixes an Xorg crash on 32-bit x86 with PAE due to corruption of the
NX bit in mprotect due to the incorrect type/value of PTE_MASK reported
by Hugh Dickins:
"Yes, thanks Jeremy: I've checked that each stage builds and runs X on
my boxes here, x86_32 and x86_32+PAE and x86_64. (So even 1/8 is
enough to fix the PAT pte_modify issue, though 2/8 then fixes
compiler warnings.)"
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Tested-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adrian Bunk [Mon, 19 May 2008 23:31:25 +0000 (01:31 +0200)]
HID: remove CVS keywords
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Dylan R Semler [Wed, 14 May 2008 09:38:14 +0000 (11:38 +0200)]
HID: Add iMON LCDs to blacklist
The new iMON LCDs from SoundGraph need to be blacklisted from HID in order to
be used by lirc.
Signed-off-by: Dylan R Semler <dylan.semler@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Xiaofan Chen [Tue, 13 May 2008 15:11:59 +0000 (17:11 +0200)]
HID: add Microchip PICKit 1 and PICkit 2 to blacklist
Microchip PICkit 1 and PICKit 2 USB Programmers are USB HID class of device but
they are not real HID device. They are now supported by libusb based programs
like the following programs.
pk2 and pk2cmd Linux port:
http://home.pacbell.net/theposts/picmicro/
usb_pickit:
http://tfc.duke.free.fr/pickit.html
usb_pickit original version:
http://charm.cs.uiuc.edu/users/olawlor/projects/2003/microchip/
Therefore it ispreferred to blacklist them.
Signed-off-by: Xiaofan Chen <xiaofanc@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Diego 'Flameeyes' Petteno [Mon, 5 May 2008 14:20:50 +0000 (16:20 +0200)]
HID: split Numlock emulation quirk from HID_QUIRK_APPLE_HAS_FN.
Since 2.6.25 the HID_QUIRK_APPLE_HAS_FN quirk is enabled even for
non-laptop Apple keyboards of the Aluminium series. The USB version of
these don't need Numlock emulation, like the laptop (and Aluminium
Wireless) do, as they have a proper keypad.
This patch splits the Numlock emulation for Apple keyboards in a
different quirk flag, so that it can be enabled for all the keyboards
but the Aluminium USB ones.
If the Numlock emulation is enabled for Aluminium USB keyboards, the
JKL and UIO keys become the numeric pad, and the rest of the keyboard
is disabled, included the key used to disable Numlock.
Additionally, these keyboard should not have a Numlock at all, as the
Numlock key is instead replaced by the 'Clear' key as usual for Apple
USB keyboards.
Signed-off-by: Diego 'Flameeyes' Petteno <flameeyes@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Paul Mackerras [Tue, 20 May 2008 10:04:12 +0000 (20:04 +1000)]
[POWERPC] Update defconfigs for desktop/server systems
Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Tue, 20 May 2008 09:46:37 +0000 (19:46 +1000)]
Merge branch 'for-2.6.26' of /linux/kernel/git/galak/powerpc into merge
Kumar Gala [Sun, 18 May 2008 18:30:03 +0000 (13:30 -0500)]
[POWERPC] Fix mpc8377_mds.dts DMA nodes to match spec
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Sun, 18 May 2008 18:25:28 +0000 (13:25 -0500)]
[POWERPC] Update arch/powerpc/boot/.gitignore
* Add dtbImage.*
* Added zImage.holly
* Folded zImage.coff.lds into zImage.*lds
* Removed some unused zImage.<foo> ignores
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Sun, 18 May 2008 18:23:03 +0000 (13:23 -0500)]
[POWERPC] Remove generated files on make clean
dtbImage.* and several zImage. targets get created but never cleaned up.
Also, moved zImage to the clean-files line associated with all other image
results (was previously duplicated).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Linus Torvalds [Mon, 19 May 2008 23:40:30 +0000 (16:40 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
at91_mci: minor cleanup
mmc: mmc host test driver
mmc: Fix omap compile by replacing dev_name with dma_dev_name
Brice Goglin [Sat, 17 May 2008 10:45:36 +0000 (12:45 +0200)]
Add maintainers for myri10ge driver
Add a MAINTAINERS entry for the myri10ge driver.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 19 May 2008 23:38:10 +0000 (16:38 -0700)]
Merge branch 'audit.b51' of git://git./linux/kernel/git/viro/audit-current
* 'audit.b51' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] list_for_each_rcu must die: audit
[patch 1/1] audit_send_reply(): fix error-path memory leak
[PATCH] open sessionid permissions
Linus Torvalds [Mon, 19 May 2008 23:37:45 +0000 (16:37 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
[PATCH] return to old errno choice in mkdir() et.al.
[Patch] fs/binfmt_elf.c: fix wrong return values
[PATCH] get rid of leak in compat_execve()
[Patch] fs/binfmt_elf.c: fix a wrong free
[PATCH] avoid multiplication overflows and signedness issues for max_fds
[PATCH] dup_fd() part 4 - race fix
[PATCH] dup_fd() - part 3
[PATCH] dup_fd() part 2
[PATCH] dup_fd() fixes, part 1
[PATCH] take init_files to fs/file.c
Linus Torvalds [Mon, 19 May 2008 23:36:28 +0000 (16:36 -0700)]
Merge branch 'for-2.6.26' of git://git./linux/kernel/git/jwboyer/powerpc-4xx
* 'for-2.6.26' of git://git.kernel.org/pub/scm/linux/kernel/git/jwboyer/powerpc-4xx:
[POWERPC] 4xx: Workaround for CHIP_11 Errata
Alan Cox [Mon, 19 May 2008 13:21:51 +0000 (14:21 +0100)]
MAINTAINERS needs further order fixing
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adrian Bunk [Mon, 19 May 2008 22:07:25 +0000 (01:07 +0300)]
[POWERPC] powerpc/mm/hash_low_32.S: Remove CVS keyword
This removes a CVS keyword that wasn't updated for a long time from a
comment.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Linus Torvalds [Mon, 19 May 2008 23:33:29 +0000 (16:33 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin SPORTS UART Driver: converting BFIN->BLACKFIN
Blackfin serial driver: add extra IRQ flag for 8250 serial driver
8250 Serial Driver: Added support for 8250-class UARTs in HV Sistemas H8606 board
Blackfin arch: Fix bug - USB fails to build for BF524/BF526
Blackfin arch: update boards defconfig files
Blackfin arch: IO Port functions to read/write unalligned memory
Blackfin arch: enable a choice to provide 4M DMA memory
Blackfin arch: cleanup the icplb/dcplb multiple hit checks
Blackfin arch: Add workaround to read edge triggered GPIOs
Blackfin arch: Sync channel defines with struct dma_register dma_io_base_addr.
Blackfin arch: Check for Anomaly
05000182
[Blackfin] arch: rename bf5xx-flash to bfin-async-flash
[Blackfin] arch: Blackfin checksum annotations
Linus Torvalds [Mon, 19 May 2008 23:33:08 +0000 (16:33 -0700)]
Merge git://git./linux/kernel/git/lethal/sh-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix up restorer in debug_trap exception return path.
sh: Make is_valid_bugaddr() more intelligent on nommu.
sh: use the common ascii hex helpers
sh: fix sh7785 master clock value
sh: Fix up thread info pointer in syscall_badsys resume path.
sh: Fix up optimized SH-4 memcpy on big endian.
sh: disable initrd defaults in .empty_zero_page.
sh: display boot params by default on entry.
Linus Torvalds [Mon, 19 May 2008 23:29:29 +0000 (16:29 -0700)]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (28 commits)
drivers/ata: trim trailing whitespace
Fixups to ATA ACPI hotplug
libata: ignore SIMG4726 config pseudo device
sata_sil24: don't use NCQ if marvell 4140 PMP is attached
libata: don't schedule LPM action seperately during probing
libata: make sure PMP notification is turned off during recovery
libata: increase PMP register access timeout to 3s
libata: ignore recovered PHY errors
libata: kill hotplug related race condition
libata: move reset freeze/thaw handling into ata_eh_reset()
libata: reorganize ata_eh_reset() no reset method path
libata: fix sata_link_hardreset() @online out parameter handling
sata_promise: other cleanups
sata_promise: mmio access cleanups
sata_promise: fix irq clearing buglets
ata: remove FIT() macro
sata_mv: ensure empty request queue for FBS-NCQ EH
sata_mv: cache main_irq_mask register in hpriv
sata_mv: disregard masked irqs
sata_mv: fix pmp drives not found
...
Arnd Bergmann [Fri, 16 May 2008 09:10:59 +0000 (11:10 +0200)]
[POWERPC] Update Cell MAINTAINERS entry, add spufs entry
The MAINTAINERS file entry for the cell platform is outdated,
even the name of the platform changed since the early days
when it was initially submitted.
The SPU file system is now maintained by Jeremy Kerr.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Jeff Garzik [Mon, 19 May 2008 21:56:10 +0000 (17:56 -0400)]
drivers/ata: trim trailing whitespace
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Matthew Garrett [Mon, 19 May 2008 16:29:34 +0000 (17:29 +0100)]
Fixups to ATA ACPI hotplug
The libata-acpi.c code currently accepts hotplug messages from both the
port and the device. This does not match the behaviour of the bay
driver, and may result in confusion when two hotplug requests are
received for the same device. This patch limits the hotplug notification
to removable ACPI devices, which in turn allows it to use the _STA
method to determine whether the device has been removed or inserted.
On removal, devices are marked as detached. On insertion, a hotplug scan
is started. This should avoid lockups caused by the ata layer attempting
to scan devices which have been removed. The uevent sending is moved
outside the spinlock in order to avoid a warning generated by it firing
when interrupts are disabled.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Sun, 18 May 2008 16:15:14 +0000 (01:15 +0900)]
libata: ignore SIMG4726 config pseudo device
I was hoping ATA_HORKAGE_NODMA | ATA_HORKAGE_SKIP_PM could keep it
happy but no even this doesn't work under certain configurations and
it's not like we can do anything useful with the cofig device anyway.
Replace ATA_HORKAGE_SKIP_PM with ATA_HORKAGE_DISABLE and use it for
the config device. This makes the device completely ignored by
libata.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Sun, 18 May 2008 16:15:13 +0000 (01:15 +0900)]
sata_sil24: don't use NCQ if marvell 4140 PMP is attached
When 4140 PMP is attached to sil24, NCQ commands to fan out port 1 and
2 (0 based) often stall if commands are in progress to other ports.
I've tried a number of things but can't tell what's going on. It
never happens w/ ahci and reportedly sata_mv which can issue NCQ
commands to multiple devices simultaneously like sil24 does.
Disable NCQ for devices behind 4140 PMP for the time being.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Sun, 18 May 2008 16:15:12 +0000 (01:15 +0900)]
libata: don't schedule LPM action seperately during probing
There's no reason to schedule LPM action after probing is complete
causing another EH iteration. Just schedule it together with probing
itself.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Sun, 18 May 2008 16:15:11 +0000 (01:15 +0900)]
libata: make sure PMP notification is turned off during recovery
PMP notification during reset can make some controllers fail reset
processing and needs to be turned off during resets. PMP attach and
full-revalidation path did this via sata_pmp_configure() but the quick
revalidation wasn't. Move the notification disable code right above
fan-out port recovery so that it's always turned off.
This fixes obscure reset failures.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Sun, 18 May 2008 16:15:10 +0000 (01:15 +0900)]
libata: increase PMP register access timeout to 3s
This timeout was set low because previously PMP register access was
done via polling and register access timeouts could stack up. This is
no longer the case. One timeout will make all following accesses fail
immediately.
In rare cases both marvell and SIMG PMPs need almost a second. Bump
it to 3s.
While at it, rename it to SATA_PMP_RW_TIMEOUT. It's not specific to
SCR access.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Sun, 18 May 2008 16:15:09 +0000 (01:15 +0900)]
libata: ignore recovered PHY errors
No reason to get overzealous about recovered comm and data errors.
Some PHYs habitually sets them w/o no good reason and being draconian
about these soft error conditions doesn't seem to help anybody.
If need ever rises, we might need to add soft PHY error condition, say
AC_ERR_MAYBE_ATA_BUS and use it only to determine whether speed down
is necessary but I don't think that's very likely to happen. It's far
more likely we'll get timeouts or fatal transmission errors if
recovered errors are so prominent that they hamper operation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Sun, 18 May 2008 16:15:08 +0000 (01:15 +0900)]
libata: kill hotplug related race condition
Originally, whole reset processing was done while the port is frozen
and SError was cleared during @postreset(). This had two race
conditions. 1: hotplug could occur after reset but before SError is
cleared and libata won't know about it. 2: hotplug could occur after
all the reset is complete but before the port is thawed. As all
events are cleared on thaw, the hotplug event would be lost.
Commit
ac371987a81c61c2efbd6931245cdcaf43baad89 kills the first race
by clearing SError during link resume but before link onlineness test.
However, this doesn't fix race #2 and in some cases clearing SError
after SRST is a good idea.
This patch solves this problem by cross checking link onlineness with
classification result after SError is cleared and port is thawed.
Reset is retried if link is online but all devices attached to the
link are unknown. As all devices will be revalidated, this one-way
check is enough to ensure that all devices are detected and
revalidated reliably.
This, luckily, also fixes the cases where host controller returns
bogus status while harddrive is spinning up after hotplug making
classification run before the device sends the first FIS and thus
causes misdetection.
Low level drivers can bypass the logic by setting class explicitly to
ATA_DEV_NONE if ever necessary (currently none requires this).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Sun, 18 May 2008 16:15:07 +0000 (01:15 +0900)]
libata: move reset freeze/thaw handling into ata_eh_reset()
Previously reset freeze/thaw handling lived outside of ata_eh_reset()
mainly because the original PMP reset code needed the port frozen
while resetting all the fan-out ports, which is no longer the case.
This patch moves freeze/thaw handling into ata_eh_reset().
@prereset() and @postreset() are now called w/o freezing the port
although @prereset() an be called frozen if the port is frozen prior
to entering ata_eh_reset().
This makes code simpler and will help removing hotplug event related
races.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Sun, 18 May 2008 16:15:06 +0000 (01:15 +0900)]
libata: reorganize ata_eh_reset() no reset method path
Reorganize ata_eh_reset() such that @prereset() is called even when no
reset method is available and if block is used instead of goto to skip
actual reset. This makes no reset case behave better (readiness wait)
and future changes easier.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Sun, 18 May 2008 16:15:05 +0000 (01:15 +0900)]
libata: fix sata_link_hardreset() @online out parameter handling
The @online out parameter is supposed to set to true iff link is
online and reset succeeded as advertised in the function description
and callers are coded expecting that. However, sata_link_reset()
didn't behave this way on device readiness test failure. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mikael Pettersson [Sat, 17 May 2008 16:49:09 +0000 (18:49 +0200)]
sata_promise: other cleanups
Minor coding-style fixes for sata_promise:
- remove stray blank lines
- fix checkpatch.pl errors; warnings about long lines
remain, but I don't intend to address those at this time
- remove two inline directives: neither is essential and
both functions are trivially inlinable anyway by virtue
of being static and having a single unique call site
- fix comment in pdc_interrupt(): the bits in PDC_INT_SEQMASK
denote SEQIDs not tags, the distinction becomes important
when NCQ gets implemented
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mikael Pettersson [Sat, 17 May 2008 16:48:15 +0000 (18:48 +0200)]
sata_promise: mmio access cleanups
This patch cleans up sata_promise's mmio accesses.
In sata_promise there are three distinct mmio address spaces:
1. global registers, offsets from host->iomap[PDC_MMIO_BAR]
2. per-port ATA registers, offsets from ap->ioaddr.cmd_addr
3. per-port SATA registers, offsets from ap->ioaddr.scr_addr
The driver currently often fails to indicate which address space
a given mmio base pointer refers to, which is a source of bugs
and confusion (see recent pdc_thaw() irq clearing bug; it's also
been an obstacle for the pending NCQ extensions).
To reduce these problems, adopt a coding style where the name of
a base pointer always indicates which address space it refers to:
1. global registers: host_mmio
2. per-port ATA registers: ata_mmio
3. per-port SATA registers: sata_mmio
Also rearrange register offset definitions to clearly indicate
which address space they belong to, and add a symbolic definition
for the previously hard-coded PHYMODE4 register.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mikael Pettersson [Sat, 17 May 2008 16:47:35 +0000 (18:47 +0200)]
sata_promise: fix irq clearing buglets
This patch fixes two bugs in sata_promise's irq status clearing paths:
1. When clearing the irq status for a specific port, the driver
read the global SEQMASK register. This is wrong because that
clears the irq status for _all_ ports.
2. pdc_thaw() incorrectly added the PDC_INT_SEQMASK host register
offset to a per-port ata engine base address. This resulted in
it reading the unrelated PDC_PKT_SUBMIT register, which did not
have the desired irq status clearing effect.
In both cases the fix is to read from the port's Command/Status
register. This also matches what Promise's own driver does.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Harvey Harrison [Wed, 14 May 2008 23:17:00 +0000 (16:17 -0700)]
ata: remove FIT() macro
Use the kernel-provided clamp_val() macro.
FIT was always applied to a member of struct ata_timing (unsigned short)
and two constants. clamp_val will not cast to short anymore.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Mon, 19 May 2008 13:01:24 +0000 (09:01 -0400)]
sata_mv: ensure empty request queue for FBS-NCQ EH
Check for an empty request queue before stopping EDMA after a FBS-NCQ error,
as per recommendation from the Marvell datasheet.
This ensures that the EDMA won't suddenly become active again
just after our subsequent check of the empty/idle bits.
Also bump DRV_VERSION.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Sat, 17 May 2008 17:38:00 +0000 (13:38 -0400)]
sata_mv: cache main_irq_mask register in hpriv
Part five of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.
Keep a cached copy of the main_irq_mask so that we don't have
to stall the CPU to read it on every pass through mv_interrupt.
This significantly speeds up interrupt handling, both for sata_mv,
and for any other driver/device sharing the same PCI IRQ line.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Sat, 17 May 2008 17:37:07 +0000 (13:37 -0400)]
sata_mv: disregard masked irqs
Part four of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.
Ignore masked IRQs in mv_interrupt().
This prevents "unexpected device interrupt while idle" messages.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Sat, 17 May 2008 17:36:30 +0000 (13:36 -0400)]
sata_mv: fix pmp drives not found
Part three of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.
Partially fix a reported bug whereby we sometimes miss seeing drives on
a port-multiplier, as reported by Gwendal Grignou <gwendal@google.com>.
The problem was that we were receiving unexpected interrupts
during EH from POLLed commands while accessing port-multiplier registers.
These unexpected interrupts can be prevented by masking the DONE_IRQ bit
for the port whenever not operating in EDMA mode.
Also fix port_stop() to mask all port interrupts.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Sat, 17 May 2008 17:35:21 +0000 (13:35 -0400)]
sata_mv: consolidate main_irq_mask updates
Part two of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.
Consolidate all updates of the host main_irq_mask register
into a single function. This simplifies maintenance,
and also prepares the way for caching it (later).
No functionality changes in this update.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Sat, 17 May 2008 17:34:42 +0000 (13:34 -0400)]
sata_mv: don't blindly enable IRQs
Part one of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.
Don't blindly enable port IRQs at host init time.
Instead, enable only the bits that we want,
which in this case is simply the PCI_ERR bit.
The per-port bits can wait until the ports are reset/probed for devices.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Wed, 14 May 2008 13:24:39 +0000 (09:24 -0400)]
sata_mv: async notify for genIIe only
Now that we handle the FIS_IRQ_CAUSE register correctly,
we can also now handle SATA asynchronous notification events.
So enable them, but only for the more modern GenIIe chips.
(older chips have unaddressed errata issues related to this).
This fixes hot plug/unplug for port-muliplier ports.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Wed, 14 May 2008 13:21:43 +0000 (09:21 -0400)]
sata_mv: group genIIe flags
Group all of the flags for GenIIe devices into a common definition,
to ensure that any updates to them are shared by all GenIIe devices.
This will help make future maintenance somewhat simpler.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Wed, 14 May 2008 13:19:30 +0000 (09:19 -0400)]
sata_mv: fis irq register fixes
Fix handling of the FIS_IRQ_CAUSE register in sata_mv.
This register exists *only* on GenIIe devices, so don't bother
writing to it on older chips. Also, it has to be read/cleared
in mv_err_intr() before clearing the main ERR_IRQ_CAUSE register.
This keeps sata_mv from getting stuck forever on certain error types.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Wed, 14 May 2008 13:18:12 +0000 (09:18 -0400)]
sata_mv: always do softreset
Always request a softreset after hardreset succeeds.
This fixes a regression reported by Martin Michlmayr <tbm@cyrius.com>.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Christophe Jaillet [Tue, 13 May 2008 19:17:30 +0000 (21:17 +0200)]
avr32/pata: avoid unnecessary memset (updated after comments)
Remove an explicit memset(.., 0, ...) to a variable allocated with
kzalloc (i.e. 'info').
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sonic Zhang [Mon, 12 May 2008 04:12:16 +0000 (12:12 +0800)]
pata-bf54x: Set ATAPI HSM to control IDE device terminate sequence.
Set ATAPI host state machine to control IDE device terminate sequence.
Some IDE harddisk may assert terminate sequence in the middle of a
formal DMA transaction and resume later. Bit DETECT_TERM in ATAPI_CTRL
register determines whether the ATAPI host state machine or the kernel
driver should take care of this case.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Linus Torvalds [Mon, 19 May 2008 21:04:47 +0000 (14:04 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/teigland/dlm
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: <linux/dlm_plock.h> should be "unifdef"ed.
dlm: fix plock dev_write return value
dlm: tcp_connect_to_sock should check for -EINVAL, not EINVAL
dlm: section mismatch warning fix
dlm: convert connections_lock in a mutex
Linus Torvalds [Mon, 19 May 2008 20:53:21 +0000 (13:53 -0700)]
Merge branch 'kvm-updates-2.6.26' of git://git./linux/kernel/git/avi/kvm
* 'kvm-updates-2.6.26' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: LAPIC: ignore pending timers if LVTT is disabled
KVM: Update MAINTAINERS for new mailing lists
KVM: Fix kvm_vcpu_block() task state race
KVM: ia64: Set KVM_IOAPIC_NUM_PINS to 48
KVM: ia64: fix GVMM module including position-dependent objects
KVM: ia64: Define new kvm_fpreg struture to replace ia64_fpreg
KVM: PIT: take inject_pending into account when emulating hlt
s390: KVM guest: fix compile error
KVM: x86 emulator: fix writes to registers with modrm encodings
Robert P. J. Day [Sat, 17 May 2008 20:58:28 +0000 (16:58 -0400)]
dlm: <linux/dlm_plock.h> should be "unifdef"ed.
Given that <linux/dlm_plock.h> contains a conditional __KERNEL__ test,
it should be moved from header-y to unifdef-y.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: David Teigland <teigland@redhat.com>
David Teigland [Tue, 13 May 2008 19:28:26 +0000 (14:28 -0500)]
dlm: fix plock dev_write return value
The return value on writes to the plock device should be
the number of bytes written. It was returning 0 instead
when an nfs lock callback was involved.
Reported-by: Nathan Straz <nstraz@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Marcin Slusarz [Sun, 11 May 2008 20:01:29 +0000 (22:01 +0200)]
dlm: tcp_connect_to_sock should check for -EINVAL, not EINVAL
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Christine Caulfield <ccaulfie@redhat.com>
Cc: David Teigland <teigland@redhat.com>
Cc: cluster-devel@redhat.com
Signed-off-by: David Teigland <teigland@redhat.com>
Leonardo Potenza [Sun, 11 May 2008 17:15:34 +0000 (19:15 +0200)]
dlm: section mismatch warning fix
Removed the section mismatch message:
WARNING: fs/dlm/dlm.o(.init.text+0x132): Section mismatch in reference from the function init_module() to the function .exit.text:dlm_netlink_exit()
Since dlm_netlink_exit() is called in the init_dlm() error handling,
the __exit annotation has been removed.
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
Signed-off-by: David Teigland <teigland@redhat.com>
Matthias Kaehlcke [Mon, 12 May 2008 15:04:51 +0000 (10:04 -0500)]
dlm: convert connections_lock in a mutex
The semaphore connections_lock is used as a mutex. Convert it to the mutex
API.
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Cc: Christine Caulfield <ccaulfie@redhat.com>
Cc: David Teigland <teigland@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Teigland <teigland@redhat.com>
Linus Torvalds [Mon, 19 May 2008 20:30:40 +0000 (13:30 -0700)]
Merge branch 'drm-patches' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: save and restore dsparb and d_state registers.
drm/i915: fix off by one in VGA save/restore of AR & CR regs.
drm: disable tasklets not IRQs when taking the drm lock spinlock
Revert "drm/vbl rework: rework how the drm deals with vblank."
Linus Torvalds [Mon, 19 May 2008 18:32:21 +0000 (11:32 -0700)]
Merge git://git./linux/kernel/git/sam/kbuild-fixes
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
Don't clean bounds.h and asm-offsets.h
kconfig: incorrect 'len' field initialisation ?
kernel-doc: allow unnamed bit-fields
kbuild: filter away debug symbols from kernel symbols
Remove *.rej pattern from .gitignore
MAINTAINERS: document names of new kbuild trees
kbuild: disable modpost warnings for linkonce sections
kbuild: escape meta characters in regular expression in make TAGS
Jan Blunck [Fri, 16 May 2008 11:54:59 +0000 (13:54 +0200)]
Don't clean bounds.h and asm-offsets.h
Since
97965478a66fbdf0f4ad5e4ecc4828f0cb548a45 ("mm: Get rid of __ZONE_COUNT")
mmzone.h includes bounds.h.
Calling make clean after make prepare removes bounds.h
again so when building external modules this fails.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
--
Christophe Jaillet [Sun, 18 May 2008 21:10:24 +0000 (23:10 +0200)]
kconfig: incorrect 'len' field initialisation ?
1) The field 'len' of the 'gstr' structure seems to track the size of the memory
already allocated for the "growable string". So the value of this field should be
the same as the 'malloc()' just above, shouldn't it ?
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Randy Dunlap [Fri, 16 May 2008 22:45:52 +0000 (15:45 -0700)]
kernel-doc: allow unnamed bit-fields
Allow for unnamed bit-fields and skip them instead of printing an
erroneous warning message for them, such as:
Warning(include/asm-s390/cio.h:103): No description found for parameter 'u32'
which contains:
struct tm_scsw {
u32 :1;
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Sam Ravnborg [Mon, 19 May 2008 18:07:58 +0000 (20:07 +0200)]
kbuild: filter away debug symbols from kernel symbols
Andi Kleen <andi@firstfloor.org>
reported that he saw a lot of symbols like this:
0000000000000b24 N DW.aio.h.
903a6d92.2
0000000000000bce N DW.task_io_accounting.h.
8d8de327.0
0000000000000bec N DW.hrtimer.h.
c23659c6.0
in his System.map / kallsyms output.
Simple solution is to skip all debugging
symbols (they are marked 'N').
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Paulo Marques <pmarques@grupopie.com>
Linus Torvalds [Mon, 19 May 2008 16:24:49 +0000 (09:24 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
snd-pcsp: silent misleading warning
snd-pcsp: depend on CONFIG_EXPERIMENTAL
snd-pcsp: put back the compatibility code for the older alsa-libs
snd-pcsp: adjust help texts to frighten users
Josh Boyer [Thu, 15 May 2008 14:43:46 +0000 (00:43 +1000)]
[POWERPC] 4xx: Workaround for CHIP_11 Errata
The PowerPC 440EP, 440GR, 440EPx, and 440GRx chips have an issue that
causes the PLB3-to-PLB4 bridge to wait indefinitely for transaction
requests that cross the end-of-memory-range boundary. Since the DDR
controller only returns the valid portion of a read request, the bridge
will prevent other PLB masters from completing their transactions.
This implements the recommended workaround for this errata for chips that
use older versions of firmware that do not already handle it. The last
4KiB of memory are hidden from the kernel to prevent the problem
transactions from occurring.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Paul Mundt [Mon, 19 May 2008 10:39:33 +0000 (19:39 +0900)]
sh: Fix up restorer in debug_trap exception return path.
There are a few different types of debug trap exceptions, though now
that they are all going through a special jump table, the restorer needs
to be unified as well.
Presently this is falling through the ret_from_fork path, which more or
less does the right thing on SH-3/4 whilst being completely unsuitable on
MMU-less targets.
Ultimately what we want here is a branch through the platform's
restore_all directly, without worrying about the retval being clobbered.
We can accomplish that through a branch to __restore_all directly, so
switch it so we come back from the jump table and branch to the restorer.
This fixes up a recursion in the nommu WARN_ON() path, as well as some
other userspace nastiness where said recursion caused serious stack
corruption.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Mon, 19 May 2008 10:32:07 +0000 (19:32 +0900)]
sh: Make is_valid_bugaddr() more intelligent on nommu.
Currently is_valid_bugaddr() is true for anything >= PAGE_OFFSET, which
happens to be 0 on nommu configurations. Make this a bit smarter by just
reading in the opcode and comparing it against the trap type that we
already know. Follows the logic from avr32.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Stas Sergeev [Sun, 18 May 2008 16:30:03 +0000 (18:30 +0200)]
snd-pcsp: silent misleading warning
It appears that alsa allows a sound buffer with size not
evenly devided by the period size. This triggers a warning in
snd-pcsp and floods the log. As a quick fix, the warning should
be disabled.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stas Sergeev [Sat, 17 May 2008 06:46:55 +0000 (08:46 +0200)]
snd-pcsp: depend on CONFIG_EXPERIMENTAL
Considering all the feedbacks I got, depending snd-pcsp on
CONFIG_EXPERIMENTAL looks like the only safe way to get out
of all the troubles at one go. :)
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stas Sergeev [Sat, 17 May 2008 06:44:41 +0000 (08:44 +0200)]
snd-pcsp: put back the compatibility code for the older alsa-libs
The attached patch adds back the compatibility code, allowing the
driver to work with older alsa-libs.
The removal was premature, it breaks the real-life configs.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stas Sergeev [Fri, 16 May 2008 10:10:03 +0000 (12:10 +0200)]
snd-pcsp: adjust help texts to frighten users
Added the warning text to the help of snd-pcsp about the possible problem
with this driver so that user can know of the problem in advance.
Also, removed the obsoleted text about ancient pc-speaker patch in
CONFIG_SOUND help.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kumar Gala [Sun, 18 May 2008 18:18:01 +0000 (13:18 -0500)]
lmb: Fix compile warning
lib/lmb.c: In function 'lmb_dump_all':
lib/lmb.c:51: warning: format '%lx' expects type 'long unsigned int', but argument 2 has type 'u64'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Linus Torvalds [Sun, 18 May 2008 22:32:44 +0000 (15:32 -0700)]
Merge branch 'hotfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'hotfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
SUNRPC: AUTH_SYS "machine creds" shouldn't use negative valued uid/gid
nfs: make nfs4_drop_state_owner() static
nfs: path_{get,put}() cleanups
nfs: replace remaining __FUNCTION__ occurrences
nfs/lsm: make NFSv4 set LSM mount options
NFSv4: Check the return value of decode_compound_hdr_arg()
nfs: fix race in nfs_dirty_request
NFS: Ensure that 'noac' and/or 'actimeo=0' turn off attribute caching
Linus Torvalds [Sun, 18 May 2008 21:36:41 +0000 (14:36 -0700)]
Linux 2.6.26-rc3
Linus Torvalds [Sun, 18 May 2008 20:56:54 +0000 (13:56 -0700)]
Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c/max6875: Really prevent 24RF08 corruption
i2c-amd756: Fix functionality flags
i2c: Kill the old driver matching scheme
i2c: Convert remaining new-style drivers to use module aliasing
i2c: Switch pasemi to the new device/driver matching scheme
i2c: Clean up Blackfin BF527 I2C device declarations
i2c-nforce2: Disable the second SMBus channel on the DFI Lanparty NF4 Expert
i2c: New co-maintainer
Geert Uytterhoeven [Sun, 18 May 2008 18:47:24 +0000 (20:47 +0200)]
m68k: Add multi_defconfig
Add multi_defconfig, to build a kernel for all supported m68k platforms,
excluding Sun 3 (Sun 3 kernels are incompatible with all other m68k platforms)
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Sun, 18 May 2008 18:47:23 +0000 (20:47 +0200)]
m68k: Update defconfigs
Update the m68k defconfigs
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Sun, 18 May 2008 18:47:22 +0000 (20:47 +0200)]
m68k: Correctly handle multi-ISA at runtime
m68k: Correctly handle multi-ISA at runtime in multi-platform kernels
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Sun, 18 May 2008 18:47:21 +0000 (20:47 +0200)]
m68k: Prefix ISA type with ISA_TYPE_
The *_ISA type defines are quite generic and cause namespace conflicts
(e.g. with `AMIGAHW_DECLARE(GG2_ISA)' in <asm/amigahw.h>) for some kernel
configurations. Use ISA_TYPE_* to avoid such conflicts.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Sun, 18 May 2008 18:47:20 +0000 (20:47 +0200)]
m68k: export m68k_mmutype
UIO needs m68k_mmutype:
ERROR: "m68k_mmutype" [drivers/uio/uio.ko] undefined!
(noticed by Christian T. Steigies)
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Sun, 18 May 2008 18:47:19 +0000 (20:47 +0200)]
m68k: Q40/Q60 floppy support is broken
Mark Q40/Q60 floppy support broken:
arch/m68k/q40/q40ints.c: In function 'q40_irq_handler':
arch/m68k/q40/q40ints.c:214: error: implicit declaration of function 'floppy_hardint'
Including <asm/floppy.h> doesn't help, as it causes a lot of additional error
messages (cfr. Sun 3x).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Sun, 18 May 2008 18:47:18 +0000 (20:47 +0200)]
m68k: Return -ENODEV if no device is found
According to the tests in do_initcalls(), the proper error code in case no
device is found is -ENODEV, not -ENXIO or -EIO.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Sun, 18 May 2008 18:47:17 +0000 (20:47 +0200)]
m68k: Some input drivers do not check the platform
Some input drivers do not check whether they're actually running on the
correct platform, causing multi-platform kernels to crash if they are not.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Sun, 18 May 2008 18:47:16 +0000 (20:47 +0200)]
m68k: Some network drivers do not check the platform
Some network drivers do not check whether they're actually running on the
correct platform, causing multi-platform kernels to crash if they are not.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Sun, 18 May 2008 18:47:15 +0000 (20:47 +0200)]
m68k: dnfb doesnt check for Apollo
The Apollo frame buffer device driver (dnfb) doesn't check whether it's
actually running on Apollo hardware, causing a crash if it isn't.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Sun, 18 May 2008 18:47:14 +0000 (20:47 +0200)]
m68k: macide doesnt check for Mac
The Macintosh IDE driver (macide) doesn't check whether it's actually running
on Mac hardware, causing a crash if it isn't.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Sun, 18 May 2008 18:47:13 +0000 (20:47 +0200)]
m68k: Correct jump if not running on HP300
When running a HP300-enabled kernel on non-HP300 hardware, a test in the early
startup code jumps to the wrong label, causing a double bus fault.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Sun, 18 May 2008 18:47:12 +0000 (20:47 +0200)]
m68k: Make gcc aware that BUG() does not return
Use `__builtin_trap()' instead of `asm volatile("illegal")' in the m68k BUG()
macros (as suggested by Andrew Pinski), to kill warnings in code that assumes
BUG() does not return.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>