OSDN Git Service
Arnd Bergmann [Thu, 16 Jun 2016 09:00:05 +0000 (11:00 +0200)]
dsa: b53: fix big-endian register access
The b53 dsa register access confusingly uses __raw register accessors
when both the CPU and the device are big-endian, but it uses little-
endian accessors when the same device is used from a little-endian
CPU, which makes no sense.
This uses normal accessors in device-endianess all the time, which
will work in all four combinations of register and CPU endianess,
and it will have the same barrier semantics in all cases.
This also seems to take care of a (false positive) warning I'm getting:
drivers/net/dsa/b53/b53_mmap.c: In function 'b53_mmap_read64':
drivers/net/dsa/b53/b53_mmap.c:109:10: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 32) | lo;
I originally planned to submit another patch for that warning
and did this one as a preparation cleanup, but it does seem to be
sufficient by itself.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Thu, 16 Jun 2016 08:09:09 +0000 (17:09 +0900)]
mpls: allow routes on ipgre devices
This appears to be necessary and sufficient to provide
MPLS in GRE (RFC4023) support.
This can be used by establishing an ipgre tunnel device
and then routing MPLS over it.
The following example will forward MPLS frames received with an outermost
MPLS label 100 over tun1, a GRE tunnel. The forwarded packet will have the
outermost MPLS LSE removed and two new LSEs added with labels 200
(outermost) and 300 (next).
ip link add name tun1 type gre remote 10.0.99.193 local 10.0.99.192 ttl 225
ip link set up dev tun1
ip addr add 10.0.98.192/24 dev tun1
ip route sh
echo 1 > /proc/sys/net/mpls/conf/eth0/input
echo 101 > /proc/sys/net/mpls/platform_labels
ip -f mpls route add 100 as 200/300 via inet 10.0.98.193
ip -f mpls route sh
Also remove unnecessary braces.
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Thu, 16 Jun 2016 06:08:29 +0000 (14:08 +0800)]
r8152: modify the check of the flag of PHY_RESET in set_speed function
In set_speed(), BMCR_RESET would be set when the flag of PHY_RESET
is set. Use BMCR_RESET to replace testing the flag of PHY_RESET.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Wed, 15 Jun 2016 22:12:49 +0000 (00:12 +0200)]
net: ethernet: ax88796: use phy_ethtool_{get|set}_link_ksettings
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Wed, 15 Jun 2016 22:12:48 +0000 (00:12 +0200)]
net: ethernet: ax88796: use phydev from struct net_device
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 16 Jun 2016 21:14:58 +0000 (14:14 -0700)]
Merge branch 'stmmac-wol'
Vincent Palatin says:
====================
net: stmmac: dwmac-rk: fixes for Wake-on-Lan on RK3288
In order to support Wake-On-Lan when using the RK3288 integrated MAC
(with an external RGMII PHY), we need to avoid shutting down the regulator
of the external PHY when the MAC is suspended as it's currently done in the MAC
platform code.
As a first step, create independant callbacks for suspend/resume rather than
re-using exit/init callbacks. So the dwmac platform driver can behave differently
on suspend where it might skip shutting the PHY and at module unloading.
Then update the dwmac-rk driver to switch off the PHY regulator only if we are
not planning to wake up from the LAN.
Finally add the PMT interrupt to the MAC device tree configuration, so we can
wake up the core from it when the PHY has received the magic packet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Palatin [Wed, 15 Jun 2016 18:32:23 +0000 (11:32 -0700)]
ARM: dts: rockchip: add interrupt for Wake-on-Lan on RK3288
In order to use Wake-on-Lan on RK3288 integrated MAC, we need to wake-up
the CPU on the PMT interrupt when the MAC and the PHY are in low power mode.
Adding the interrupt declaration.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Palatin [Wed, 15 Jun 2016 18:32:22 +0000 (11:32 -0700)]
net: stmmac: dwmac-rk: keep the PHY up for WoL
When suspending the machine, do not shutdown the external PHY by cutting
its regulator in the mac platform driver suspend code if Wake-on-Lan is enabled,
else it cannot wake us up.
In order to do this, split the suspend/resume callbacks from the
init/exit callbacks, so we can condition the power-down on the lack of
need to wake-up from the LAN but do it unconditionally when unloading the
module.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Palatin [Wed, 15 Jun 2016 18:32:21 +0000 (11:32 -0700)]
net: stmmac: allow to split suspend/resume from init/exit callbacks
Let the stmmac platform drivers provide dedicated suspend and resume
callbacks rather than always re-using the init and exits callbacks.
If the driver does not provide the suspend or resume callback, we fall
back to the old behavior trying to use exit or init.
This allows a specific platform to perform only a partial power-down on
suspend if Wake-on-Lan is enabled but always perform the full shutdown
sequence if the module is unloaded.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Wed, 15 Jun 2016 17:15:06 +0000 (01:15 +0800)]
sctp: change sk state to CLOSED instead of CLOSING in sctp_sock_migrate
Commit
d46e416c11c8 ("sctp: sctp should change socket state when
shutdown is received") may set sk_state CLOSING in sctp_sock_migrate,
but inet_accept doesn't allow the sk_state other than ESTABLISHED/
CLOSED for sctp. So we will change sk_state to CLOSED, instead of
CLOSING, as actually sk is closed already there.
Fixes:
d46e416c11c8 ("sctp: sctp should change socket state when shutdown is received")
Reported-by: Ye Xiaolong <xiaolong.ye@intel.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fabien Siron [Wed, 15 Jun 2016 15:37:49 +0000 (15:37 +0000)]
netlink: Add comment to warn about deprecated netlink rings attribute request
Signed-off-by: Fabien Siron <fabien.siron@epita.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 16 Jun 2016 06:42:58 +0000 (23:42 -0700)]
Merge branch 'bpf-fd-array-release'
Daniel Borkmann says:
====================
bpf: improve fd array release
This set improves BPF perf fd array map release wrt to purging
entries, first two extend the API as needed. Please see individual
patches for more details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 15 Jun 2016 20:47:14 +0000 (22:47 +0200)]
bpf, maps: flush own entries on perf map release
The behavior of perf event arrays are quite different from all
others as they are tightly coupled to perf event fds, f.e. shown
recently by commit
e03e7ee34fdd ("perf/bpf: Convert perf_event_array
to use struct file") to make refcounting on perf event more robust.
A remaining issue that the current code still has is that since
additions to the perf event array take a reference on the struct
file via perf_event_get() and are only released via fput() (that
cleans up the perf event eventually via perf_event_release_kernel())
when the element is either manually removed from the map from user
space or automatically when the last reference on the perf event
map is dropped. However, this leads us to dangling struct file's
when the map gets pinned after the application owning the perf
event descriptor exits, and since the struct file reference will
in such case only be manually dropped or via pinned file removal,
it leads to the perf event living longer than necessary, consuming
needlessly resources for that time.
Relations between perf event fds and bpf perf event map fds can be
rather complex. F.e. maps can act as demuxers among different perf
event fds that can possibly be owned by different threads and based
on the index selection from the program, events get dispatched to
one of the per-cpu fd endpoints. One perf event fd (or, rather a
per-cpu set of them) can also live in multiple perf event maps at
the same time, listening for events. Also, another requirement is
that perf event fds can get closed from application side after they
have been attached to the perf event map, so that on exit perf event
map will take care of dropping their references eventually. Likewise,
when such maps are pinned, the intended behavior is that a user
application does bpf_obj_get(), puts its fds in there and on exit
when fd is released, they are dropped from the map again, so the map
acts rather as connector endpoint. This also makes perf event maps
inherently different from program arrays as described in more detail
in commit
c9da161c6517 ("bpf: fix clearing on persistent program
array maps").
To tackle this, map entries are marked by the map struct file that
added the element to the map. And when the last reference to that map
struct file is released from user space, then the tracked entries
are purged from the map. This is okay, because new map struct files
instances resp. frontends to the anon inode are provided via
bpf_map_new_fd() that is called when we invoke bpf_obj_get_user()
for retrieving a pinned map, but also when an initial instance is
created via map_create(). The rest is resolved by the vfs layer
automatically for us by keeping reference count on the map's struct
file. Any concurrent updates on the map slot are fine as well, it
just means that perf_event_fd_array_release() needs to delete less
of its own entires.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 15 Jun 2016 20:47:13 +0000 (22:47 +0200)]
bpf, maps: extend map_fd_get_ptr arguments
This patch extends map_fd_get_ptr() callback that is used by fd array
maps, so that struct file pointer from the related map can be passed
in. It's safe to remove map_update_elem() callback for the two maps since
this is only allowed from syscall side, but not from eBPF programs for these
two map types. Like in per-cpu map case, bpf_fd_array_map_update_elem()
needs to be called directly here due to the extra argument.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 15 Jun 2016 20:47:12 +0000 (22:47 +0200)]
bpf, maps: add release callback
Add a release callback for maps that is invoked when the last
reference to its struct file is gone and the struct file about
to be released by vfs. The handler will be used by fd array maps.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 16 Jun 2016 05:26:27 +0000 (22:26 -0700)]
Merge branch 'sfc-rx-vlan-filtering'
Edward Cree says:
====================
sfc: RX VLAN filtering
Adds support for VLAN-qualified receive filters on EF10 hardware.
This is needed when running as a guest if the hypervisor has enabled
vfs-vlan-restrict, in which case the firmware rejects filters not qualified
with VLAN 0.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:52:08 +0000 (17:52 +0100)]
sfc: Fix VLAN filtering feature if vPort has VLAN_RESTRICT flag
If vPort has VLAN_RESTRICT flag, VLAN tagged traffic will not be
delivered without corresponding Rx filters which may be proxied to and
moderated by hypervisor.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Wed, 15 Jun 2016 16:51:48 +0000 (17:51 +0100)]
sfc: Update MCDI protocol definitions
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:51:36 +0000 (17:51 +0100)]
sfc: Disable VLAN filtering by default if not strictly required
If should be done after net_dev->hw_features initialization, to keep the
feature there to be able to enable it later using ethtool.
VLAN filtering is enforced and fixed if vPort requires usage of VLAN
filters to receive tagged traffic.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Habets [Wed, 15 Jun 2016 16:51:07 +0000 (17:51 +0100)]
sfc: VLAN filters must only be created if the firmware supports this.
If it is not supported we simply disable the feature.
For the feature to work we need firmware filter support for
OUTER_VID + LOC_MAC and for OUTER_VID + LOC_MAC_IG.
The low-latency firmware can match on OUTER_VID + LOC_MAC but not on
OUTER_VID + LOC_MAC_IG.
For the capture packet firmware it is the other way around.
Only the full-feature variant can match on both combinations.
Incorporates a fix by Andrew Rybchenko <Andrew.Rybchenko@oktetlabs.ru>
in the net_dev->[hw_]features handling.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:49:30 +0000 (17:49 +0100)]
sfc: Fix dup unknown multicast/unicast filters after datapath reset
Filter match flags are not unique criteria to be mapped to priority
because of both unknown unicast and unknown multicast are mapped to
LOC_MAC_IG. So, local MAC is required to map filter to priority.
MCDI filter flags is unique criteria to find filter priority.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Wed, 15 Jun 2016 16:49:05 +0000 (17:49 +0100)]
sfc: Refactor checks for invalid filter ID
Nearly every time we call efx_ef10_filter_remove_unsafe, we first check
for EFX_EF10_FILTER_ID_INVALID, in which case we do nothing. So move
that check into the function, simplifying all the call sites.
Also, change the return type to void, since none of the callers check it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Habets [Wed, 15 Jun 2016 16:48:49 +0000 (17:48 +0100)]
sfc: Take mac_lock before calling efx_ef10_filter_table_probe
When trying to enslave an SFC interface to a bond the following BUG_ON was
hit:
kernel BUG [in ef10.c]!
CPU: 0 PID: 4383 Comm: ifenslave Tainted: G
...
Call Trace:
efx_ef10_filter_add_vlan+0x121/0x180 [sfc]
efx_ef10_filter_table_probe+0x2a2/0x4f0 [sfc]
efx_ef10_set_mac_address+0x370/0x6d0 [sfc]
efx_set_mac_address+0x7d/0x120 [sfc]
dev_set_mac_address+0x43/0xa0
bond_enslave+0x337/0xea0 [bonding]
This comes from function efx_ef10_filter_vlan_sync_rx_mode.
To solve the bug we ensure the mac_lock is taken before calling
efx_ef10_filter_add_vlan. But to avoid a priority inversion mac_lock must
be taken before filter_sem.
To satisfy these requirements we end up taking mac_lock in
efx_ef10_vport_set_mac_address, efx_ef10_set_mac_address,
efx_ef10_sriov_set_vf_vlan and efx_probe_filters.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:48:32 +0000 (17:48 +0100)]
sfc: Implement ndo_vlan_rx_{add, kill}_vid() callbacks
Supports HW VLAN filtering, en/disabled using ethtool.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:48:14 +0000 (17:48 +0100)]
sfc: Implement list of VLANs added over interface
Right now it contains dummy VLAN entry with unspecified VID only.
The entry is used for the case when HW VLAN filtering is not used.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:47:36 +0000 (17:47 +0100)]
sfc: Make EF10 filter management helper functions VLAN-aware
It is a step to support VLAN filtering in HW.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:45:56 +0000 (17:45 +0100)]
sfc: Store unicast and multicast promisc flag with address cache
These flags are built when address cache is updated.
The information will be required when VLAN filtering is added and address
cache is used without re-sync.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:45:36 +0000 (17:45 +0100)]
sfc: Move filter IDs to per-VLAN data structure
It is a step to support VLAN filtering in HW.
Until then, there is only one struct efx_ef10_filter_vlan per struct
efx_ef10_filter_table, with no VLAN information yet.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:44:20 +0000 (17:44 +0100)]
sfc: Forget filter ID when the filter is marked old
It is required to remove setting of filter IDs to invalid from multicast
and unicast addresses caching functions.
Add initialization to invalid when filter table is created.
Add paranoid checks to track consistency.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Wed, 15 Jun 2016 16:43:43 +0000 (17:43 +0100)]
sfc: Assert filter_sem write locked when required
Based on a patch by Andrew Rybchenko <Andrew.Rybchenko@oktetlabs.ru>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:43:20 +0000 (17:43 +0100)]
sfc: Add efx_nic member with fixed netdev features
It allows to change set of fixed features on datapath reset.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:43:00 +0000 (17:43 +0100)]
sfc: Move last mc_promisc flag to EF10 filter table state
It is used for EF10 only and logically belongs to EF10 filter table state.
It is OK that it is reset to false on filter table recreation since all
filters are removed on destruction.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:42:26 +0000 (17:42 +0100)]
sfc: Define macro with EF10 offload feature
It is useful to simplify features addition.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 16 Jun 2016 05:22:17 +0000 (22:22 -0700)]
Merge tag 'rxrpc-rewrite-
20160615' of git://git./linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Rework endpoint record handling
Here's the next part of the AF_RXRPC rewrite. In this set I rework
endpoint record handling. There are two types of endpoint record, local
and peer. The local endpoint record is used as an anchor for the transport
socket that AF_RXRPC uses (at the moment a UDP socket). Local endpoints
can be shared between AF_RXRPC sockets under certain restricted
circumstances.
The peer endpoint is a record of the remote end. It is (or will be) used
to keep track MTU and RTT values and, with these changes, is used to find
the call(s) to abort when a network error occurs.
The following significant changes are made:
(1) The local endpoint event handling code is split out into its own file.
(2) The local endpoint list bottom half-excluding spinlock is removed as
things are arranged such that sk_user_data will not change whilst the
transport socket callbacks are in progress.
(3) Local endpoints can now only be shared if they have the same transport
address (as before) and have a local service ID of 0 (ie. they're not
listening for incoming calls). This prevents callbacks from a server
to one process being picked up by another process.
(4) Local endpoint destruction is now accomplished by the same work item
as processes events, meaning that the destructor doesn't need to wait
for the event processor.
(5) Peer endpoints are now held in a hash table rather than a flat list.
(6) Peer endpoints are now destroyed by RCU rather than by work item.
(7) Peer endpoints are now differentiated by local endpoint and remote
transport port in addition to remote transport address and transport
type and family.
This means that a firewall that excludes access between a particular
local port and remote port won't cause calls to be aborted that use a
different port pair.
(8) Error report handling now no longer assumes that the source is always
an IPv4 ICMP message from a UDP port and has assumptions that an ICMP
message comes from an IPv4 socket removed. At some point IPv6 support
will be added.
(9) Peer endpoints rather than local endpoints are now the anchor point
for distributing network error reports.
(10) Both types of endpoint records are now disposed of as soon as all
references to them are gone. There is less hanging around and once
their usage counts hit zero, records can no longer be resurrected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 16 Jun 2016 04:44:33 +0000 (21:44 -0700)]
Merge branch 'liquidio-next'
Raghu Vatsavayi says:
====================
liquidio: Updates and Bug fixes
Following are updates for liquidio bug fixes and driver
support for new firmware interface. These updates are divided
into smaller logical patches as mentioned by you. These set of
nine patches should be applied in the following order as some of
them depend on earlier patches in the list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Tue, 14 Jun 2016 23:54:51 +0000 (16:54 -0700)]
liquidio: Introduce new octeon2/3 header
Added support for new instruction header for octeon2/octeon3(ih) and
corresponding changes.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Tue, 14 Jun 2016 23:54:50 +0000 (16:54 -0700)]
liquidio: Replace ifidx for FW commands
This patch decoupled the firmware side ifidx and host side interface
number. It also has some minor name change for linkinfo sturct field.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Tue, 14 Jun 2016 23:54:49 +0000 (16:54 -0700)]
liquidio: New driver FW command structure
This patch is for new driver/firmware control command structure
(octnic_packet_params and octnic_cmd_setup ) and resultant code changes.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Tue, 14 Jun 2016 23:54:48 +0000 (16:54 -0700)]
liquidio: Consider PTP for packet size calculations
This patch is to refactor packet size calculations to support PTP enabled
for 66xx and 68xx cards and also other cards that do not support PTP.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Tue, 14 Jun 2016 23:54:47 +0000 (16:54 -0700)]
liquidio: RX desc alloc changes
This patch is to add page based buffers for receive side descriptors of
the driver and separate free routines for rx and tx buffers.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Tue, 14 Jun 2016 23:54:46 +0000 (16:54 -0700)]
liquidio:RX queue alloc changes
This patch is to allocate rx queue's memory based on numa node and also use
page based buffers for rx traffic improvements.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Tue, 14 Jun 2016 23:54:45 +0000 (16:54 -0700)]
liquidio:Scatter gather list per IQ
This patch is to allocate and manage scatter gather lists per
input queue(iq's) and remove queue's interdependence.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Tue, 14 Jun 2016 23:54:44 +0000 (16:54 -0700)]
liquidio: Host queue mapping changes
This patch is to allocate the input queues based on Numa node in tx path
and queue mapping changes based on the mapping info provided by firmware.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Tue, 14 Jun 2016 23:54:43 +0000 (16:54 -0700)]
liquidio: Avoid double free during soft command
This patch is to resolve the double free issue by checking proper return
values from soft command.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Tue, 14 Jun 2016 23:29:15 +0000 (16:29 -0700)]
ila: Fix checksum neutral mapping
The algorithm for checksum neutral mapping is incorrect. This problem
was being hidden since we were previously always performing checksum
offload on the translated addresses and only with IPv6 HW csum.
Enabling an ILA router shows the issue.
Corrected algorithm:
old_loc is the original locator in the packet, new_loc is the value
to overwrite with and is found in the lookup table. old_flag is
the old flag value (zero of CSUM_NEUTRAL_FLAG) and new_flag is
then (old_flag ^ CSUM_NEUTRAL_FLAG) & CSUM_NEUTRAL_FLAG.
Need SUM(new_id + new_flag + diff) == SUM(old_id + old_flag) for
checksum neutral translation.
Solving for diff gives:
diff = (old_id - new_id) + (old_flag - new_flag)
compute_csum_diff8(new_id, old_id) gives old_id - new_id
If old_flag is set
old_flag - new_flag = old_flag = CSUM_NEUTRAL_FLAG
Else
old_flag - new_flag = -new_flag = ~CSUM_NEUTRAL_FLAG
Tested:
- Implemented a user space program that creates random addresses
and random locators to overwrite. Compares the checksum over
the address before and after translation (must always be equal)
- Enabled ILA router and showed proper operation.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philip Prindeville [Tue, 14 Jun 2016 21:53:02 +0000 (15:53 -0600)]
net: ipv4: Add ability to have GRE ignore DF bit in IPv4 payloads
In the presence of firewalls which improperly block ICMP Unreachable
(including Fragmentation Required) messages, Path MTU Discovery is
prevented from working.
A workaround is to handle IPv4 payloads opaquely, ignoring the DF bit--as
is done for other payloads like AppleTalk--and doing transparent
fragmentation and reassembly.
Redux includes the enforcement of mutual exclusion between this feature
and Path MTU Discovery as suggested by Alexander Duyck.
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 14 Jun 2016 18:37:21 +0000 (11:37 -0700)]
net: vrf: Switch dst dev to loopback on device delete
Attempting to delete a VRF device with a socket bound to it can stall:
unregister_netdevice: waiting for red to become free. Usage count = 1
The unregister is waiting for the dst to be released and with it
references to the vrf device. Similar to dst_ifdown switch the dst
dev to loopback on delete for all of the dst's for the vrf device
and release the references to the vrf device.
Fixes:
193125dbd8eb2 ("net: Introduce VRF device driver")
Fixes:
35402e3136634 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 16 Jun 2016 04:37:10 +0000 (21:37 -0700)]
Merge tag 'shared' of git://git./linux/kernel/git/leon/linux-rdma
Mellanox shared code between RDMA and net-next trees
This is Mellanox mlx5_core shared code for both net-next and RDMA
trees for 4.8 kernel cycle.
Arnd Bergmann [Tue, 14 Jun 2016 10:03:17 +0000 (12:03 +0200)]
mdio: mux: avoid 'maybe-uninitialized' warning
The latest changes to the MDIO code introduced a false-positive
warning with gcc-6 (possibly others):
drivers/net/phy/mdio-mux.c: In function 'mdio_mux_init':
drivers/net/phy/mdio-mux.c:188:3: error: 'parent_bus_node' may be used uninitialized in this function [-Werror=maybe-uninitialized]
It's easy to avoid the warning by making sure the parent_bus_node
is initialized in both cases at the start of the function, since
the later 'of_node_put()' call is also valid for a NULL pointer
argument.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes:
f20e6657a875 ("mdio: mux: Enhanced MDIO mux framework for integrated multiplexers")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 16 Jun 2016 03:41:24 +0000 (20:41 -0700)]
Merge branch '6lowpan-ndisc'
Alexander Aring says:
====================
6lowpan: introduce 6lowpan-nd
David can you please pick-up this patch-serie for your net-next tree?
Thanks in advance.
This patch series introduces the ndisc ops callback structure to add different
handling for IPv6 neighbour discovery cache functionality. It implements at first
the two following use-cases:
- 6CO handling as userspace option (For all 6LoWPAN layers, BTLE/802.15.4) [0]
- short address handling for 802.15.4 6LoWPAN only [1]
Since my last patch series, I completely changed the whole ndisc_ops callback
structure to not replace the whole ndisc functionality at recv/send level of
NS/NA/RS/RA which I send in my previous patch-series "6lowpan: introduce basic
6lowpan-nd". I changed it now to add different handling in a very low-level way
of ndisc functionality.
The ndisc_ops don't must be registered to dev->ndisc_ops anymore, if they are not
set, then no additional ipv6 ndisc handling will be done.
This patch series now introduce a complete handling of short address for
802.15.4 6LoWPAN in case of send/recv of NA/NS/RS and RA. In case of RA
(receive only) and PIO we also need a second prefix + short-address based
address.
This callback structure can be used later (I hope) for RFC 6775 [0]. This RFC
defines some new option fields and messages for 6LoWPAN-ND. This patch series
does not implement RFC 6775 (except we decide now to handle 6CO in userspace).
Additional we can use the current ops for parse/fill ndisc options for kernel
handled ndisc messages to add 6CIO, see [2].
I tested RA/NS/NA/RS messages with short address which seems to work, what I
didn't test is the redirect messages since I don't know how to generate them.
The short address for redirect messages are also some special case here, because
the short address by a L3 target address lookuped by neighbour cache need to be
added.
btw:
According to [3] sending redirect messages should be also disabled by default
on 6lowpan interfaces, but can be activated afterwards. This is maybe
something for the ipv6_devconf structure. There is a "accept_redirects" but
no "disable_redirects".
- Alex
[0] https://tools.ietf.org/html/rfc6775
[1] https://tools.ietf.org/html/rfc4944#section-8
[2] https://tools.ietf.org/html/rfc7400
changes since v3:
- add acked-by and reviewed-by tags
- fix url references in cover-letter
- add cover-letter that this patch series is okay to go through net-next tree
changes since RFC:
- add lowlevel functions __ndisc_opt_addr_space,
__ndisc_opt_addr_data and __ndisc_fill_addr_option for corresponding
functions which doesn't requires net_device argument.
- move ndisc_ops e.g. ndisc_ops_fill_addr_option function call into the
corresponding device argument function ndisc_fill_addr_option.
(Introduced a special static inline function for redirect handling).
- fix error handling in addrconf_prefix_rcv_add_addr.
(Please see, introduce new API handling that second address registration
(in case of 802.15.4 6LoWPAN) will still be notified if failed, because
dev->addr was successful.
- add ieee802154 sub-directory in short address entry for 6lowpan UAPI.
- add lowpan_802154_is_valid_src_short_addr, because 802.15.4 6lowpan
defines the first bit as multicast (don't know how this can be working
at the end, because some hardware addresses will handle such addresses
in L2 as unicast. See:
https://www.iana.org/assignments/_6lowpan-parameters/_6lowpan-parameters.xhtml#_6lowpan-parameters-2
changes since v2:
- Introduce ndisc_ops to have our own implementation for dealing with NS/NA
which allows also to support RFC6775 (e.g. ARO).
- add handling for handling 6CO as userspace option for RA messages in
case of 6LoWPAN interfaces.
- change lowpan_is_ll to check on linklayer type only.
- added some reviewed-by's.
- move short addr slaac to net/6lowpan instead ipv6 handling.
- add handling for context based address compression in case for
short address as link-layer address.
- change strategy to use short address, a short address will always be used
when it's available.
- Handle override flag in NA messages to update short address information or
not.
====================
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:27 +0000 (21:20 +0200)]
6lowpan: add support for 802.15.4 short addr handling
This patch adds necessary handling for use the short address for
802.15.4 6lowpan. It contains support for IPHC address compression
and new matching algorithmn to decide which link layer address will be
used for 802.15.4 frame.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:26 +0000 (21:20 +0200)]
6lowpan: add support for getting short address
In case of sending RA messages we need some way to get the short address
from an 802.15.4 6LoWPAN interface. This patch will add a temporary
debugfs entry for experimental userspace api.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:25 +0000 (21:20 +0200)]
6lowpan: introduce 6lowpan-nd
This patch introduce different 6lowpan handling for receive and transmit
NS/NA messages for the ipv6 neighbour discovery. The first use-case is
for supporting 802.15.4 short addresses inside the option fields and
handling for RFC6775 6CO option field as userspace option.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:24 +0000 (21:20 +0200)]
ipv6: export several functions
This patch exports some neighbour discovery functions which can be used
by 6lowpan neighbour discovery ops functionality then.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:23 +0000 (21:20 +0200)]
ipv6: introduce neighbour discovery ops
This patch introduces neighbour discovery ops callback structure. The
idea is to separate the handling for 6LoWPAN into the 6lowpan module.
These callback offers 6lowpan different handling, such as 802.15.4 short
address handling or RFC6775 (Neighbor Discovery Optimization for IPv6
over 6LoWPANs).
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:22 +0000 (21:20 +0200)]
addrconf: put prefix address add in an own function
This patch moves the functionality to add a RA PIO prefix generated
address in an own function. This move prepares to add a hook for
adding a second address for a second link-layer address. E.g. short
address for 802.15.4 6LoWPAN.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:21 +0000 (21:20 +0200)]
ndisc: add __ndisc_fill_addr_option function
This patch adds __ndisc_fill_addr_option as low-level function for
ndisc_fill_addr_option which doesn't depend on net_device parameter.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:20 +0000 (21:20 +0200)]
ndisc: add __ndisc_opt_addr_data function
This patch adds __ndisc_opt_addr_data as low-level function for
ndisc_opt_addr_data which doesn't depend on net_device parameter.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:19 +0000 (21:20 +0200)]
ndisc: add __ndisc_opt_addr_space function
This patch adds __ndisc_opt_addr_space as low-level function for
ndisc_opt_addr_space which doesn't depend on net_device parameter.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:18 +0000 (21:20 +0200)]
6lowpan: remove ipv6 module request
Since we use exported function from ipv6 kernel module we don't need to
request the module anymore to have ipv6 functionality.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:17 +0000 (21:20 +0200)]
6lowpan: add 802.15.4 short addr slaac
This patch adds the autoconfiguration if a valid 802.15.4 short address
is available for 802.15.4 6LoWPAN interfaces.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:16 +0000 (21:20 +0200)]
6lowpan: add private neighbour data
This patch will introduce a 6lowpan neighbour private data. Like the
interface private data we handle private data for generic 6lowpan and
for link-layer specific 6lowpan.
The current first use case if to save the short address for a 802.15.4
6lowpan neighbour.
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 15 Jun 2016 21:46:05 +0000 (14:46 -0700)]
Merge branch 'cxgb4-sriov-sysfs'
Hariprasad Shenai says:
====================
Add SRIOV configuration via sysfs and few fixes
This series adds support to configure SR-IOV via PCI sysfs interface,
reduces resource allocation in kdump kernel by disabling offload. Also
synchronize unicast and multicast mac address, even in the interface is in
Promiscuous mode.
This patch series has been created against net-next tree and includes
patches on cxgb4 and cxgb4vf driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Tue, 14 Jun 2016 09:09:32 +0000 (14:39 +0530)]
cxgb4/cxgb4vf: Synchronize all MAC addresses
Even if interface is in Promiscuous mode/Allmulti mode synchronize
MAC addresses.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Tue, 14 Jun 2016 09:09:31 +0000 (14:39 +0530)]
cxgb4: Enable SR-IOV configuration via PCI sysfs interface
Implement callback in the driver for the new PCI bus driver
interface that allows the user to enable/disable SR-IOV
virtual functions in a device via the sysfs interface.
Deprecate module parameter used to configure SRIOV
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Tue, 14 Jun 2016 09:09:30 +0000 (14:39 +0530)]
cxgb4: Force cxgb4 driver as MASTER in kdump kernel
When is_kdump_kernel() is true, Forcing cxgb4 driver as Master so we can
reinitialize the Firmware/Chip. Also reduce memory usage by disabling
offload.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 15 Jun 2016 21:08:36 +0000 (14:08 -0700)]
Merge branch 'sched_skb_free_defer'
Eric Dumazet says:
====================
net_sched: defer skb freeing while changing qdiscs
qdiscs/classes are changed under RTNL protection and often
while blocking BH and root qdisc spinlock.
When lots of skbs need to be dropped, we free
them under these locks causing TX/RX freezes,
and more generally latency spikes.
I saw spikes of 50+ ms on quite fast hardware...
This patch series adds a simple queue protected by RTNL
where skbs can be placed until RTNL is released.
Note that this might also serve in the future for optional
reinjection of packets when a qdisc is replaced.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 14 Jun 2016 03:21:59 +0000 (20:21 -0700)]
net_sched: sch_fq: defer skb freeing
sfq_reset() can use rtnl_kfree_skbs() instead of kfree_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 14 Jun 2016 03:21:58 +0000 (20:21 -0700)]
net_sched: sch_pie: defer skb freeing
pie_change() can use rtnl_qdisc_drop() to benefit from
deferred freeing.
pie_reset() is already using qdisc_reset_queue()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 14 Jun 2016 03:21:57 +0000 (20:21 -0700)]
net_sched: sch_netem: defer skb freeing
rtnl_kfree_skbs() can be used in tfifo_reset()
It would be nice if we could iterate through rb tree instead
of removing one skb at a time, and build a single skb chain.
But this is left for a future patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 14 Jun 2016 03:21:56 +0000 (20:21 -0700)]
net_sched: sch_htb: defer skb freeing
Both htb_reset() and htb_destroy() can use __qdisc_reset_queue()
instead of __skb_queue_purge() to defer skb freeing of internal
queues.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 14 Jun 2016 03:21:55 +0000 (20:21 -0700)]
net_sched: sch_hhf: defer skb freeing
Both hhf_reset() and hhf_change() can use rtnl_kfree_skbs()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 14 Jun 2016 03:21:54 +0000 (20:21 -0700)]
net_sched: fq_codel: defer skb freeing
Both fq_codel_change() and fq_codel_reset() can use rtnl_kfree_skbs()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 14 Jun 2016 03:21:53 +0000 (20:21 -0700)]
net_sched: sch_fq: defer skb freeing
Both fq_change() and fq_reset() can use rtnl_kfree_skbs()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 14 Jun 2016 03:21:52 +0000 (20:21 -0700)]
net_sched: sch_codel: defer skb freeing in codel_change()
codel_change() can use rtnl_qdisc_drop()
to defer expensive skb freeing after locks are released.
codel_reset() already has support for deferred skb freeing
because it uses qdisc_reset_queue()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 14 Jun 2016 03:21:51 +0000 (20:21 -0700)]
net_sched: sch_choke: defer skb freeing
choke_reset() and choke_change() can use rtnl_qdisc_drop()
to defer expensive skb freeing after locks are released.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 14 Jun 2016 03:21:50 +0000 (20:21 -0700)]
net_sched: add the ability to defer skb freeing
qdisc are changed under RTNL protection and often
while blocking BH and root qdisc spinlock.
When lots of skbs need to be dropped, we free
them under these locks causing TX/RX freezes,
and more generally latency spikes.
This commit adds rtnl_kfree_skbs(), used to queue
skbs for deferred freeing.
Actual freeing happens right after RTNL is released,
with appropriate scheduling points.
rtnl_qdisc_drop() can also be used in place
of disc_drop() when RTNL is held.
qdisc_reset_queue() and __qdisc_reset_queue() get
the new behavior, so standard qdiscs like pfifo, pfifo_fast...
have their ->reset() method automatically handled.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Tue, 14 Jun 2016 00:46:22 +0000 (20:46 -0400)]
tipc: add neighbor monitoring framework
TIPC based clusters are by default set up with full-mesh link
connectivity between all nodes. Those links are expected to provide
a short failure detection time, by default set to 1500 ms. Because
of this, the background load for neighbor monitoring in an N-node
cluster increases with a factor N on each node, while the overall
monitoring traffic through the network infrastructure increases at
a ~(N * (N - 1)) rate. Experience has shown that such clusters don't
scale well beyond ~100 nodes unless we significantly increase failure
discovery tolerance.
This commit introduces a framework and an algorithm that drastically
reduces this background load, while basically maintaining the original
failure detection times across the whole cluster. Using this algorithm,
background load will now grow at a rate of ~(2 * sqrt(N)) per node, and
at ~(2 * N * sqrt(N)) in traffic overhead. As an example, each node will
now have to actively monitor 38 neighbors in a 400-node cluster, instead
of as before 399.
This "Overlapping Ring Supervision Algorithm" is completely distributed
and employs no centralized or coordinated state. It goes as follows:
- Each node makes up a linearly ascending, circular list of all its N
known neighbors, based on their TIPC node identity. This algorithm
must be the same on all nodes.
- The node then selects the next M = sqrt(N) - 1 nodes downstream from
itself in the list, and chooses to actively monitor those. This is
called its "local monitoring domain".
- It creates a domain record describing the monitoring domain, and
piggy-backs this in the data area of all neighbor monitoring messages
(LINK_PROTOCOL/STATE) leaving that node. This means that all nodes in
the cluster eventually (default within 400 ms) will learn about
its monitoring domain.
- Whenever a node discovers a change in its local domain, e.g., a node
has been added or has gone down, it creates and sends out a new
version of its node record to inform all neighbors about the change.
- A node receiving a domain record from anybody outside its local domain
matches this against its own list (which may not look the same), and
chooses to not actively monitor those members of the received domain
record that are also present in its own list. Instead, it relies on
indications from the direct monitoring nodes if an indirectly
monitored node has gone up or down. If a node is indicated lost, the
receiving node temporarily activates its own direct monitoring towards
that node in order to confirm, or not, that it is actually gone.
- Since each node is actively monitoring sqrt(N) downstream neighbors,
each node is also actively monitored by the same number of upstream
neighbors. This means that all non-direct monitoring nodes normally
will receive sqrt(N) indications that a node is gone.
- A major drawback with ring monitoring is how it handles failures that
cause massive network partitionings. If both a lost node and all its
direct monitoring neighbors are inside the lost partition, the nodes in
the remaining partition will never receive indications about the loss.
To overcome this, each node also chooses to actively monitor some
nodes outside its local domain. Those nodes are called remote domain
"heads", and are selected in such a way that no node in the cluster
will be more than two direct monitoring hops away. Because of this,
each node, apart from monitoring the member of its local domain, will
also typically monitor sqrt(N) remote head nodes.
- As an optimization, local list status, domain status and domain
records are marked with a generation number. This saves senders from
unnecessarily conveying unaltered domain records, and receivers from
performing unneeded re-adaptations of their node monitoring list, such
as re-assigning domain heads.
- As a measure of caution we have added the possibility to disable the
new algorithm through configuration. We do this by keeping a threshold
value for the cluster size; a cluster that grows beyond this value
will switch from full-mesh to ring monitoring, and vice versa when
it shrinks below the value. This means that if the threshold is set to
a value larger than any anticipated cluster size (default size is 32)
the new algorithm is effectively disabled. A patch set for altering the
threshold value and for listing the table contents will follow shortly.
- This change is fully backwards compatible.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 14 Jun 2016 00:14:12 +0000 (17:14 -0700)]
net: vrf: Update flags and features settings
1. Default VRF devices to not having a qdisc (IFF_NO_QUEUE). Users
can add one as desired.
2. Disable adding a VLAN to a VRF device.
3. Enable offloads and hardware features similar to other logical
devices (e.g., dummy, veth)
Change provides a significant boost in TCP stream Tx performance,
from ~2,700 Mbps to ~18,100 Mbps and makes throughput close to the
performance without a VRF (18,500 Mbps). netperf TCP_STREAM benchmark
using qemu with virtio+vhost for the NICs
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Mon, 13 Jun 2016 22:00:04 +0000 (00:00 +0200)]
tun: fix csum generation for tap devices
The commit
34166093639b ("tuntap: use common code for virtio_net_hdr
and skb GSO conversion") replaced the tun code for header manipulation
with the generic helpers. While doing so, it implictly moved the
skb_partial_csum_set() invocation after eth_type_trans(), which
invalidate the current gso start/offset values.
Fix it by moving the helper invocation before the mac pulling.
Fixes:
34166093639 ("tuntap: use common code for virtio_net_hdr and skb GSO conversion")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 15 Jun 2016 20:58:34 +0000 (13:58 -0700)]
Merge branch 'skb_array'
Michael S. Tsirkin says:
====================
skb_array: array based FIFO for skbs
This is in response to the proposal by Jason to make tun
rx packet queue lockless using a circular buffer.
My testing seems to show that at least for the common usecase
in networking, which isn't lockless, circular buffer
with indices does not perform that well, because
each index access causes a cache line to bounce between
CPUs, and index access causes stalls due to the dependency.
By comparison, an array of pointers where NULL means invalid
and !NULL means valid, can be updated without messing up barriers
at all and does not have this issue.
On the flip side, cache pressure may be caused by using large queues.
tun has a queue of 1000 entries by default and that's 8K.
At this point I'm not sure this can be solved efficiently.
The correct solution might be sizing the queues appropriately.
Here's an implementation of this idea: it can be used more
or less whenever sk_buff_head can be used, except you need
to know the queue size in advance.
As this might be useful outside of networking, I implemented
a generic array of void pointers, with a type-safe wrapper for skbs.
It remains to be seen whether resizing is required, in case it is
I included patches implementing resizing by holding both the
consumer and the producer locks.
I think this code works fine without any extra memory barriers since we
always read and write the same location, so the accesses can not be
reordered.
Multiple writes of the same value into memory would mess things up
for us, I don't think compilers would do it though.
But if people feel it's better to be safe wrt compiler optimizations,
specifying queue as volatile would probably do it in a cleaner way
than converting all accesses to READ_ONCE/WRITE_ONCE. Thoughts?
The only issue is with calls within a loop using the __ptr_ring_XXX
accessors - in theory compiler could hoist accesses out of the loop.
Following volatile-considered-harmful.txt I merely
documented that callers that busy-poll should invoke cpu_relax().
Most people will use the external skb_array_XXX APIs with a spinlock,
so this should not be an issue for them.
Eric Dumazet suggested adding an extra pointer to skb for when
we have a single outstanding packet. I could not figure out
a way to implement this without a shared consumer/producer lock
though, which would cause cache line bounces by itself.
Jesper, Jason, I know that both of you tested this,
please post Tested-by tags for whatever was tested.
changes since v7
fix typos noticed by Jesper Brouer
changes since v6
resize implemented. peek/full calls are no longer lockless
replaced _FIELD macros with _CALL which invoke a function
on the pointer rather than just returning a value
destroy now scans the array and frees all queued skbs
changes since v5
implemented a generic ptr_ring api, and
made skb_array a type-safe wrapper
apis for taking the spinlock in different contexts
following expected usecase in tun
changes since v4 (v3 was never posted)
documentation
dropped SKB_ARRAY_MIN_SIZE heuristic
unit test (in userspace, included as patch 2)
changes since v2:
fixed integer overflow pointed out by Eric.
added some comments.
changes since v1:
fixed bug pointed out by Eric.
====================
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael S. Tsirkin [Mon, 13 Jun 2016 20:54:50 +0000 (23:54 +0300)]
skb_array: resize support
Update skb_array after ptr_ring API changes.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael S. Tsirkin [Mon, 13 Jun 2016 20:54:45 +0000 (23:54 +0300)]
ptr_ring: resize support
This adds ring resize support. Seems to be necessary as
users such as tun allow userspace control over queue size.
If resize is used, this costs us ability to peek at queue without
consumer lock - should not be a big deal as peek and consumer are
usually run on the same CPU.
If ring is made bigger, ring contents is preserved. If ring is made
smaller, extra pointers are passed to an optional destructor callback.
Cleanup function also gains destructor callback such that
all pointers in queue can be cleaned up.
This changes some APIs but we don't have any users yet,
so it won't break bisect.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael S. Tsirkin [Mon, 13 Jun 2016 20:54:41 +0000 (23:54 +0300)]
skb_array: array based FIFO for skbs
A simple array based FIFO of pointers. Intended for net stack so uses
skbs for type safety. Implemented as a set of wrappers around ptr_ring.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael S. Tsirkin [Mon, 13 Jun 2016 20:54:36 +0000 (23:54 +0300)]
ptr_ring: ring test
Add ringtest based unit test for ptr ring.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael S. Tsirkin [Mon, 13 Jun 2016 20:54:31 +0000 (23:54 +0300)]
ptr_ring: array based FIFO for pointers
A simple array based FIFO of pointers. Intended for net stack which
commonly has a single consumer/producer.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Mon, 13 Jun 2016 20:46:28 +0000 (13:46 -0700)]
net_sched: make tcf_hash_check() boolean
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 15 Jun 2016 19:34:34 +0000 (12:34 -0700)]
Merge branch 'vrf-ipv6-mcast-link-local'
David Ahern says:
====================
net: vrf: Handle ipv6 multicast and link-local addresses
IPv6 multicast and link-local addresses require special handling by the
VRF driver. Rather than using the VRF device index and full FIB lookups,
packets to/from these addresses should use direct FIB lookups based on
the VRF device table.
Multicast routes do not make sense for the L3 master device directly.
Accordingly, do not add mcast routes for the device, and the VRF driver
should fail attempts to send packets to ipv6 mcast addresses on the
device (e.g, ping6 ff02::1%<vrf> should fail)
With this change connections into and out of a VRF enslaved device work
for multicast and link-local addresses (icmp, tcp, and udp). e.g.,
1. packets into VM with VRF config:
ping6 -c3 fe80::e0:f9ff:fe1c:b974%br1
ping6 -c3 ff02::1%br1
ssh -6 fe80::e0:f9ff:fe1c:b974%br1
2. packets going out a VRF enslaved device:
ping6 -c3 fe80::18f8:83ff:fe4b:7a2e%eth1
ping6 -c3 ff02::1%eth1
ssh -6 root@fe80::18f8:83ff:fe4b:7a2e%eth1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 13 Jun 2016 20:44:19 +0000 (13:44 -0700)]
net: vrf: Handle ipv6 multicast and link-local addresses
IPv6 multicast and link-local addresses require special handling by the
VRF driver:
1. Rather than using the VRF device index and full FIB lookups,
packets to/from these addresses should use direct FIB lookups based on
the VRF device table.
2. fail sends/receives on a VRF device to/from a multicast address
(e.g, make ping6 ff02::1%<vrf> fail)
3. move the setting of the flow oif to the first dst lookup and revert
the change in icmpv6_echo_reply made in
ca254490c8dfd ("net: Add VRF
support to IPv6 stack"). Linklocal/mcast addresses require use of the
skb->dev.
With this change connections into and out of a VRF enslaved device work
for multicast and link-local addresses work (icmp, tcp, and udp)
e.g.,
1. packets into VM with VRF config:
ping6 -c3 fe80::e0:f9ff:fe1c:b974%br1
ping6 -c3 ff02::1%br1
ssh -6 fe80::e0:f9ff:fe1c:b974%br1
2. packets going out a VRF enslaved device:
ping6 -c3 fe80::18f8:83ff:fe4b:7a2e%eth1
ping6 -c3 ff02::1%eth1
ssh -6 root@fe80::18f8:83ff:fe4b:7a2e%eth1
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 13 Jun 2016 20:44:18 +0000 (13:44 -0700)]
net: ipv6: Do not add multicast route for l3 master devices
L3 master devices are virtual devices similar to the loopback
device. Link local and multicast routes for these devices do
not make sense. The ipv6 addrconf code already skips adding a
linklocal address; do the same for the mcast route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 13 Jun 2016 20:44:17 +0000 (13:44 -0700)]
net: l3mdev: Remove const from flowi6 arg to get_rt6_dst
Allow drivers to pass flow arg to functions where the arg is not const
and allow the driver to make updates as needed (eg., setting oif).
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 15 Jun 2016 19:21:05 +0000 (12:21 -0700)]
Merge branch 'af_iucv-big-bufs'
Ursula Braun says:
====================
s390: af_iucv patches
here are improvements for af_iucv relaxing the pressure to allocate
big contiguous kernel buffers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eugene Crosser [Mon, 13 Jun 2016 16:46:16 +0000 (18:46 +0200)]
af_iucv: use paged SKBs for big inbound messages
When an inbound message is bigger than a page, allocate a paged SKB,
and subsequently use IUCV receive primitive with IPBUFLST flag.
This relaxes the pressure to allocate big contiguous kernel buffers.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eugene Crosser [Mon, 13 Jun 2016 16:46:15 +0000 (18:46 +0200)]
af_iucv: remove fragment_skb() to use paged SKBs
Before introducing paged skbs in the receive path, get rid of the
function `iucv_fragment_skb()` that replaces one large linear skb
with several smaller linear skbs.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eugene Crosser [Mon, 13 Jun 2016 16:46:14 +0000 (18:46 +0200)]
af_iucv: use paged SKBs for big outbound messages
When an outbound message is bigger than a page, allocate and fill
a paged SKB, and subsequently use IUCV send primitive with IPBUFLST
flag. This relaxes the pressure to allocate big contiguous kernel
buffers.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Shiyan [Mon, 13 Jun 2016 15:52:17 +0000 (18:52 +0300)]
dt: bindings: Add bindings for Cirrus Logic CS89x0 ethernet chip
Add device tree binding documentation details for Cirrus Logic
CS8900/CS8920 ethernet chip.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Shiyan [Mon, 13 Jun 2016 15:51:05 +0000 (18:51 +0300)]
net: cx89x0: Add DT support
Add DT support to the Cirrus Logic CS89x0 driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Mon, 4 Apr 2016 13:00:35 +0000 (14:00 +0100)]
rxrpc: Rework local endpoint management
Rework the local RxRPC endpoint management.
Local endpoint objects are maintained in a flat list as before. This
should be okay as there shouldn't be more than one per open AF_RXRPC socket
(there can be fewer as local endpoints can be shared if their local service
ID is 0 and they share the same local transport parameters).
Changes:
(1) Local endpoints may now only be shared if they have local service ID 0
(ie. they're not being used for listening).
This prevents a scenario where process A is listening of the Cache
Manager port and process B contacts a fileserver - which may then
attempt to send CM requests back to B. But if A and B are sharing a
local endpoint, A will get the CM requests meant for B.
(2) We use a mutex to handle lookups and don't provide RCU-only lookups
since we only expect to access the list when opening a socket or
destroying an endpoint.
The local endpoint object is pointed to by the transport socket's
sk_user_data for the life of the transport socket - allowing us to
refer to it directly from the sk_data_ready and sk_error_report
callbacks.
(3) atomic_inc_not_zero() now exists and can be used to only share a local
endpoint if the last reference hasn't yet gone.
(4) We can remove rxrpc_local_lock - a spinlock that had to be taken with
BH processing disabled given that we assume sk_user_data won't change
under us.
(5) The transport socket is shut down before we clear the sk_user_data
pointer so that we can be sure that the transport socket's callbacks
won't be invoked once the RCU destruction is scheduled.
(6) Local endpoints have a work item that handles both destruction and
event processing. The means that destruction doesn't then need to
wait for event processing. The event queues can then be cleared after
the transport socket is shut down.
(7) Local endpoints are no longer available for resurrection beyond the
life of the sockets that had them open. As soon as their last ref
goes, they are scheduled for destruction and may not have their usage
count moved from 0.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 4 Apr 2016 13:00:34 +0000 (14:00 +0100)]
rxrpc: Separate local endpoint event handling out into its own file
Separate local endpoint event handling out into its own file preparatory to
overhauling the object management aspect (which remains in the original
file).
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 4 Apr 2016 13:00:34 +0000 (14:00 +0100)]
rxrpc: Use the peer record to distribute network errors
Use the peer record to distribute network errors rather than the transport
object (which I want to get rid of). An error from a particular peer
terminates all calls on that peer.
For future consideration:
(1) For ICMP-induced errors it might be worth trying to extract the RxRPC
header from the offending packet, if one is returned attached to the
ICMP packet, to better direct the error.
This may be overkill, though, since an ICMP packet would be expected
to be relating to the destination port, machine or network. RxRPC
ABORT and BUSY packets give notice at RxRPC level.
(2) To also abort connection-level communications (such as CHALLENGE
packets) where indicted by an error - but that requires some revamping
of the connection event handling first.
Signed-off-by: David Howells <dhowells@redhat.com>