OSDN Git Service
Jens Axboe [Wed, 12 Dec 2018 16:18:11 +0000 (09:18 -0700)]
nvme: provide fallback for discard alloc failure
[ Upstream commit
cb5b7262b011cfb793519bf97e54dff5282da23c ]
When boxes are run near (or to) OOM, we have a problem with the discard
page allocation in nvme. If we fail allocating the special page, we
return busy, and it'll get retried. But since ordering is honored for
dispatch requests, we can keep retrying this same IO and failing. Behind
that IO could be requests that want to free memory, but they never get
the chance.
Allocate a fixed discard page per controller for a safe fallback, and use
that if the initial allocation fails.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Giridhar Malavali [Mon, 10 Dec 2018 20:36:24 +0000 (12:36 -0800)]
scsi: qla2xxx: Fix for FC-NVMe discovery for NPIV port
[ Upstream commit
835aa4f2691e4ed4ed16de81f3cabf17a87a164f ]
This patch fixes NVMe discovery by setting SKIP_PRLI flag, so that PRLI is
driven by driver and is retried when the NPIV port is detected to have NVMe
capability.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Himanshu Madhani [Mon, 10 Dec 2018 20:36:23 +0000 (12:36 -0800)]
scsi: qla2xxx: Fix NPIV handling for FC-NVMe
[ Upstream commit
5e6803b409ba3c18434de6693062d98a470bcb1e ]
This patch fixes issues with NPIV port with FC-NVMe. Clean up code for
remoteport delete and also call nvme_delete when deleting VPs.
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Tue, 11 Dec 2018 03:37:01 +0000 (19:37 -0800)]
scsi: lpfc: Enable Management features for IF_TYPE=6
[ Upstream commit
719162bd5bb968203397b9b1d0dd30a9797bbd09 ]
Addition of support for if_type=6 missed several checks for interface type,
resulting in the failure of several key management features such as
firmware dump and loopback testing.
Correct the checks on the if_type so that both SLI4 IF_TYPE's 2 and 6 are
supported.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans de Goede [Sat, 8 Dec 2018 12:59:24 +0000 (13:59 +0100)]
ACPI / LPSS: Ignore acpi_device_fix_up_power() return value
[ Upstream commit
1a2fa02f7489dc4d746f2a15fb77b3ce1affade8 ]
Ignore acpi_device_fix_up_power() return value. If we return an error
we end up with acpi_default_enumeration() still creating a platform-
device for the device and we end up with the device still being used
but without the special LPSS related handling which is not useful.
Specicifically ignoring the error fixes the touchscreen no longer
working after a suspend/resume on a Prowise PT301 tablet.
This tablet has a broken _PS0 method on the touchscreen's I2C controller,
causing acpi_device_fix_up_power() to fail, causing fallback to standard
platform-dev handling and specifically causing acpi_lpss_save/restore_ctx
to not run.
The I2C controllers _PS0 method does actually turn on the device, but then
does some more nonsense which fails when run during early boot trying to
use I2C opregion handling on another not-yet registered I2C controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Arnd Bergmann [Mon, 10 Dec 2018 21:58:38 +0000 (22:58 +0100)]
ARM: ks8695: fix section mismatch warning
[ Upstream commit
4aa64677330beeeed721b4b122884dabad845d66 ]
WARNING: vmlinux.o(.text+0x13250): Section mismatch in reference from the function acs5k_i2c_init() to the (unknown reference) .init.data:(unknown)
The function acs5k_i2c_init() references
the (unknown reference) __initdata (unknown).
This is often because acs5k_i2c_init lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dave Chinner [Wed, 12 Dec 2018 16:46:21 +0000 (08:46 -0800)]
xfs: zero length symlinks are not valid
[ Upstream commit
43feeea88c9cb2955b9f7ba8152ec5abeea42810 ]
A log recovery failure has been reproduced where a symlink inode has
a zero length in extent form. It was caused by a shutdown during a
combined fstress+fsmark workload.
The underlying problem is the issue in xfs_inactive_symlink(): the
inode is unlocked between the symlink inactivation/truncation and
the inode being freed. This opens a window for the inode to be
written to disk before it xfs_ifree() removes it from the unlinked
list, marks it free in the inobt and zeros the mode.
For shortform inodes, the fix is simple. xfs_ifree() clears the data
fork state, so there's no need to do it in xfs_inactive_symlink().
This means the shortform fork verifier will not see a zero length
data fork as it mirrors the inode size through to xfs_ifree()), and
hence if the inode gets written back and the fork verifiers are run
they will still see a fork that matches the on-disk inode size.
For extent form (remote) symlinks, it is a little more tricky. Here
we explicitly set the inode size to zero, so the above race can lead
to zero length symlinks on disk. Because the inode is unlinked at
this point (i.e. on the unlinked list) and unreferenced, it can
never be seen again by a user. Hence when we set the inode size to
zeor, also change the type to S_IFREG. xfs_ifree() expects S_IFREG
inodes to be of zero length, and so this avoids all the problems of
zero length symlinks ever hitting the disk. It also avoids the
problem of needing to handle zero length symlink inodes in log
recovery to replay the extent free intents and the remaining
deferops to free the extents the symlink used.
Also add a couple of asserts to warn us if zero length symlinks end
up in either the symlink create or inactivation paths.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Thomas Meyer [Sun, 2 Dec 2018 20:52:11 +0000 (21:52 +0100)]
PM / AVS: SmartReflex: NULL check before some freeing functions is not needed
[ Upstream commit
14d338a857f05f894ba3badd9e6d3039c68b8180 ]
NULL check before some freeing functions is not needed.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Gal Pressman [Mon, 10 Dec 2018 15:17:25 +0000 (17:17 +0200)]
RDMA/vmw_pvrdma: Use atomic memory allocation in create AH
[ Upstream commit
a276a4d93bf1580d737f38d1810e5f4b166f3edd ]
Create address handle callback should not sleep, use GFP_ATOMIC instead of
GFP_KERNEL for memory allocation.
Fixes:
29c8d9eba550 ("IB: Add vmw_pvrdma driver")
Cc: Adit Ranadive <aditr@vmware.com>
Signed-off-by: Gal Pressman <galpress@amazon.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Will Deacon [Tue, 11 Dec 2018 13:41:32 +0000 (13:41 +0000)]
arm64: preempt: Fix big-endian when checking preempt count in assembly
[ Upstream commit
7faa313f05cad184e8b17750f0cbe5216ac6debb ]
Commit
396244692232 ("arm64: preempt: Provide our own implementation of
asm/preempt.h") extended the preempt count field in struct thread_info
to 64 bits, so that it consists of a 32-bit count plus a 32-bit flag
indicating whether or not the current task needs rescheduling.
Whilst the asm-offsets definition of TSK_TI_PREEMPT was updated to point
to this new field, the assembly usage was left untouched meaning that a
32-bit load from TSK_TI_PREEMPT on a big-endian machine actually returns
the reschedule flag instead of the count.
Whilst we could fix this by pointing TSK_TI_PREEMPT at the count field,
we're actually better off reworking the two assembly users so that they
operate on the whole 64-bit value in favour of inspecting the thread
flags separately in order to determine whether a reschedule is needed.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Lijun Ou [Sat, 8 Dec 2018 10:40:09 +0000 (18:40 +0800)]
RDMA/hns: Fix the bug while use multi-hop of pbl
[ Upstream commit
4af07f01f7a787ba5158352b98c9e3cb74995a1c ]
It will prevent multiply overflow when defines the pbl for u64 type.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Aaro Koskinen [Tue, 4 Dec 2018 17:57:42 +0000 (19:57 +0200)]
ARM: OMAP1: fix USB configuration for device-only setups
[ Upstream commit
c7b7b5cbd0c859b1546a5a3455d457708bdadf4c ]
Currently we do USB configuration only if the host mode (CONFIG_USB)
is enabled. But it should be done also in the case of device-only setups,
so change the condition to CONFIG_USB_SUPPORT. This allows to use
omap_udc on Palm Tungsten E.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vadim Pasternak [Thu, 15 Nov 2018 17:26:57 +0000 (17:26 +0000)]
platform/x86: mlx-platform: Fix LED configuration
[ Upstream commit
440f343df1996302d9a3904647ff11b689bf27bc ]
Exchange LED configuration between msn201x and next generation systems
types.
Bug was introduced when LED driver activation was added to mlx-platform.
LED configuration for the three new system MQMB7, MSN37, MSN34 was
assigned to MSN21 and vice versa. This bug affects MSN21 only and
likely requires backport to v4.19.
Fixes:
1189456b1cce ("platform/x86: mlx-platform: Add LED platform driver activation")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tony Lindgren [Mon, 10 Dec 2018 22:11:26 +0000 (14:11 -0800)]
bus: ti-sysc: Check for no-reset and no-idle flags at the child level
[ Upstream commit
4014c08ba39476a18af546186da625a6833a1529 ]
With ti-sysc, we need to now have the device tree properties for
ti,no-reset-on-init and ti,no-idle-on-init at the module level instead
of the child device level.
Let's check for these properties at the child device level to enable
quirks, and warn about moving the properties to the module level.
Otherwise am335x-evm based boards tagging gpio1 with ti,no-reset-on-init
will have their DDR power disabled if wired up in such a tricky way.
Note that this should not be an issue for earlier kernels as we don't
rely on this until the dts files have been updated to probe with ti-sysc
interconnect target driver.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Suzuki K Poulose [Mon, 10 Dec 2018 18:07:33 +0000 (18:07 +0000)]
arm64: smp: Handle errors reported by the firmware
[ Upstream commit
f357b3a7e17af7736d67d8267edc1ed3d1dd9391 ]
The __cpu_up() routine ignores the errors reported by the firmware
for a CPU bringup operation and looks for the error status set by the
booting CPU. If the CPU never entered the kernel, we could end up
in assuming stale error status, which otherwise would have been
set/cleared appropriately by the booting CPU.
Reported-by: Steve Capper <steve.capper@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Steve Capper [Thu, 6 Dec 2018 22:50:40 +0000 (22:50 +0000)]
arm64: mm: Prevent mismatched 52-bit VA support
[ Upstream commit
a96a33b1ca57dbea4285893dedf290aeb8eb090b ]
For cases where there is a mismatch in ARMv8.2-LVA support between CPUs
we have to be careful in allowing secondary CPUs to boot if 52-bit
virtual addresses have already been enabled on the boot CPU.
This patch adds code to the secondary startup path. If the boot CPU has
enabled 52-bit VAs then ID_AA64MMFR2_EL1 is checked to see if the
secondary can also enable 52-bit support. If not, the secondary is
prevented from booting and an error message is displayed indicating why.
Technically this patch could be implemented using the cpufeature code
when considering 52-bit userspace support. However, we employ low level
checks here as the cpufeature code won't be able to run if we have
mismatched 52-bit kernel va support.
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tony Lindgren [Wed, 5 Dec 2018 22:48:51 +0000 (14:48 -0800)]
ARM: dts: Fix hsi gdd range for omap4
[ Upstream commit
e9e685480b74aef3f3d0967dadb52eea3ff625d2 ]
While reviewing the missing mcasp ranges I noticed omap4 hsi range
for gdd is wrong so let's fix it.
I'm not aware of any omap4 devices in mainline kernel though that use
hsi though.
Fixes:
84badc5ec5fc ("ARM: dts: omap4: Move l4 child devices to probe
them with ti-sysc")
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Helge Deller [Thu, 15 Nov 2018 20:06:34 +0000 (21:06 +0100)]
parisc: Fix HP SDC hpa address output
[ Upstream commit
c4bff35ca1bfba886da6223c9fed76a2b1382b8e ]
Show the hpa address of the HP SDC instead of a hashed value, e.g.:
HP SDC: HP SDC at 0xf0201000, IRQ 23 (NMI IRQ 24)
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Helge Deller [Thu, 15 Nov 2018 20:09:59 +0000 (21:09 +0100)]
parisc: Fix serio address output
[ Upstream commit
785145171d17af2554128becd6a7c8f89e101141 ]
We want the hpa addresses printed in the serio modules, not some
virtual ioremap()ed address, e.g.:
serio: gsc-ps2-keyboard port at 0xf0108000 irq 22 @ 2:0:11
serio: gsc-ps2-mouse port at 0xf0108100 irq 22 @ 2:0:12
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabio Estevam [Wed, 5 Dec 2018 18:10:01 +0000 (16:10 -0200)]
ARM: dts: imx53-voipac-dmm-668: Fix memory node duplication
[ Upstream commit
998a84c27a7f3f9133d32af64e19c05cec161a1a ]
imx53-voipac-dmm-668 has two memory nodes, but the correct representation
would be to use a single one with two reg entries - one for each RAM chip
select, so fix it accordingly.
Reported-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabio Estevam [Mon, 26 Nov 2018 12:40:54 +0000 (10:40 -0200)]
ARM: dts: imx25: Fix memory node duplication
[ Upstream commit
59d8bb363f563e4a147a291037bf979cb8ff9a59 ]
Boards based on imx25 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx25.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabio Estevam [Mon, 26 Nov 2018 12:40:53 +0000 (10:40 -0200)]
ARM: dts: imx27: Fix memory node duplication
[ Upstream commit
38715dcd49b4430ac5b6bc1293278d91a4d32bd5 ]
Boards based on imx27 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx27.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabio Estevam [Mon, 26 Nov 2018 12:40:52 +0000 (10:40 -0200)]
ARM: dts: imx1: Fix memory node duplication
[ Upstream commit
62864d5665c4fc636d3021f829b3ac00fa058e30 ]
Boards based on imx1 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx1.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabio Estevam [Mon, 26 Nov 2018 12:08:55 +0000 (10:08 -0200)]
ARM: dts: imx23: Fix memory node duplication
[ Upstream commit
b629e83520fafe6f4c2f3e8c88c78a496fc4987c ]
Boards based on imx23 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx23.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabio Estevam [Fri, 23 Nov 2018 13:25:19 +0000 (11:25 -0200)]
ARM: dts: imx50: Fix memory node duplication
[ Upstream commit
aab5e3ea95b958cf22a24e756a84e635bdb081c1 ]
imx50-evk has duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx50.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabio Estevam [Tue, 20 Nov 2018 15:59:45 +0000 (13:59 -0200)]
ARM: dts: imx6sl: Fix memory node duplication
[ Upstream commit
7fa8ab65ee15e386558ac5e971004712da91e2dd ]
Boards based on imx6sl have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx6sl.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabio Estevam [Tue, 20 Nov 2018 15:59:44 +0000 (13:59 -0200)]
ARM: dts: imx6sx: Fix memory node duplication
[ Upstream commit
216f35fedd8688c8b654ebfbad18c6e64713fad7 ]
Boards based on imx6sx have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx6sx.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabio Estevam [Tue, 20 Nov 2018 15:59:43 +0000 (13:59 -0200)]
ARM: dts: imx6ul: Fix memory node duplication
[ Upstream commit
750d8df6e7b269b828f66631a1d39ea027afc92a ]
Boards based on imx6ul have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx6ul.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabio Estevam [Tue, 6 Nov 2018 15:40:47 +0000 (13:40 -0200)]
ARM: dts: imx7: Fix memory node duplication
[ Upstream commit
29988e867cb17de7119e971f9acfad2c3fccdb47 ]
Boards based on imx7 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx7s.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabio Estevam [Tue, 6 Nov 2018 15:40:46 +0000 (13:40 -0200)]
ARM: dts: imx35: Fix memory node duplication
[ Upstream commit
8721610a6c2b8c42fc57819d8c3bfbb9166f95a3 ]
Boards based on imx35 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx35.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabio Estevam [Tue, 6 Nov 2018 15:40:45 +0000 (13:40 -0200)]
ARM: dts: imx31: Fix memory node duplication
[ Upstream commit
013d37e4707e24c7b9bc3fc55aeda55ce9c2b262 ]
Boards based on imx31 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx31.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabio Estevam [Mon, 5 Nov 2018 21:14:46 +0000 (19:14 -0200)]
ARM: dts: imx53: Fix memory node duplication
[ Upstream commit
e8fd17b900a4a1e3a8bef7b44727cbad35db05a7 ]
Boards based on imx53 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx53.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabio Estevam [Mon, 5 Nov 2018 21:14:45 +0000 (19:14 -0200)]
ARM: dts: imx51: Fix memory node duplication
[ Upstream commit
6a9681168b83c62abfa457c709f2f4b126bd6b92 ]
Boards based on imx51 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx51.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Uwe Kleine-König [Wed, 28 Nov 2018 09:04:16 +0000 (10:04 +0100)]
ARM: debug-imx: only define DEBUG_IMX_UART_PORT if needed
[ Upstream commit
7c41ea57beb2aee96fa63091a457b1a2826f3c42 ]
If debugging on i.MX is enabled DEBUG_IMX_UART_PORT defines which UART
is used for the debug output. If however debugging is off don't only
hide the then unused config item but drop it completely by using a
dependency instead of a conditional prompt.
This fixes DEBUG_IMX_UART_PORT being present in the kernel config even
if DEBUG_LL is disabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Masami Hiramatsu [Mon, 5 Nov 2018 09:00:43 +0000 (18:00 +0900)]
tracing: Lock event_mutex before synth_event_mutex
[ Upstream commit
fc800a10be26017f8f338bc8e500d48e3e6429d9 ]
synthetic event is using synth_event_mutex for protecting
synth_event_list, and event_trigger_write() path acquires
locks as below order.
event_trigger_write(event_mutex)
->trigger_process_regex(trigger_cmd_mutex)
->event_hist_trigger_func(synth_event_mutex)
On the other hand, synthetic event creation and deletion paths
call trace_add_event_call() and trace_remove_event_call()
which acquires event_mutex. In that case, if we keep the
synth_event_mutex locked while registering/unregistering synthetic
events, its dependency will be inversed.
To avoid this issue, current synthetic event is using a 2 phase
process to create/delete events. For example, it searches existing
events under synth_event_mutex to check for event-name conflicts, and
unlocks synth_event_mutex, then registers a new event under event_mutex
locked. Finally, it locks synth_event_mutex and tries to add the
new event to the list. But it can introduce complexity and a chance
for name conflicts.
To solve this simpler, this introduces trace_add_event_call_nolock()
and trace_remove_event_call_nolock() which don't acquire
event_mutex inside. synthetic event can lock event_mutex before
synth_event_mutex to solve the lock dependency issue simpler.
Link: http://lkml.kernel.org/r/154140844377.17322.13781091165954002713.stgit@devbox
Reviewed-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Tested-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Linus Walleij [Fri, 19 Oct 2018 07:00:51 +0000 (09:00 +0200)]
ARM: dts: Fix up SQ201 flash access
[ Upstream commit
d88b11ef91b15d0af9c0676cbf4f441a0dff0c56 ]
This sets the partition information on the SQ201 to be read
out from the RedBoot partition table, removes the static
partition table and sets our boot options to mount root from
/dev/mtdblock2 where the squashfs+JFFS2 resides.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Fri, 30 Nov 2018 00:09:40 +0000 (16:09 -0800)]
scsi: lpfc: Fix dif and first burst use in write commands
[ Upstream commit
7c4042a4d0b7532cfbc90478fd3084b2dab5849e ]
When dif and first burst is used in a write command wqe, the driver was not
properly setting fields in the io command request. This resulted in no dif
bytes being sent and invalid xfer_rdy's, resulting in the io being aborted
by the hardware.
Correct the wqe initializaton when both dif and first burst are used.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Fri, 30 Nov 2018 00:09:32 +0000 (16:09 -0800)]
scsi: lpfc: Fix kernel Oops due to null pring pointers
[ Upstream commit
5a9eeff57f340238c39c95d8e7e54c96fc722de7 ]
Driver is hitting null pring pointers in lpfc_do_work().
Pointer assignment occurs based on SLI-revision. If recovering after an
error, its possible the sli revision for the port was cleared, making the
lpfc_phba_elsring() not return a ring pointer, thus the null pointer.
Add SLI revision checking to lpfc_phba_elsring() and status checking to all
callers.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bart Van Assche [Tue, 27 Nov 2018 23:51:55 +0000 (15:51 -0800)]
scsi: target/tcmu: Fix queue_cmd_ring() declaration
[ Upstream commit
e7f411049f5164ee6db6c3434c07302846f09990 ]
This patch does not change any functionality but avoids that sparse
complains about the queue_cmd_ring() function and its callers.
Fixes:
6fd0ce79724d ("tcmu: prep queue_cmd_ring to be used by unmap wq")
Reviewed-by: David Disseldorp <ddiss@suse.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Uwe Kleine-König [Thu, 17 Oct 2019 19:22:18 +0000 (21:22 +0200)]
pwm: bcm-iproc: Prevent unloading the driver module while in use
[ Upstream commit
24906a41eecb73d51974ade0847c21e429beec60 ]
The owner member of struct pwm_ops must be set to THIS_MODULE to
increase the reference count of the module such that the module cannot
be removed while its code is in use.
Fixes:
daa5abc41c80 ("pwm: Add support for Broadcom iProc PWM controller")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dan Carpenter [Thu, 7 Nov 2019 07:48:47 +0000 (10:48 +0300)]
block: drbd: remove a stray unlock in __drbd_send_protocol()
[ Upstream commit
8e9c523016cf9983b295e4bc659183d1fa6ef8e0 ]
There are two callers of this function and they both unlock the mutex so
this ends up being a double unlock.
Fixes:
44ed167da748 ("drbd: rcu_read_lock() and rcu_dereference() for tconn->net_conf")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ahmed Zaki [Thu, 31 Oct 2019 12:12:43 +0000 (06:12 -0600)]
mac80211: fix station inactive_time shortly after boot
[ Upstream commit
285531f9e6774e3be71da6673d475ff1a088d675 ]
In the first 5 minutes after boot (time of INITIAL_JIFFIES),
ieee80211_sta_last_active() returns zero if last_ack is zero. This
leads to "inactive time" showing jiffies_to_msecs(jiffies).
# iw wlan0 station get fc:ec:da:64:a6:dd
Station fc:ec:da:64:a6:dd (on wlan0)
inactive time:
4294894049 ms
.
.
connected time: 70 seconds
Fix by returning last_rx if last_ack == 0.
Signed-off-by: Ahmed Zaki <anzaki@gmail.com>
Link: https://lore.kernel.org/r/20191031121243.27694-1-anzaki@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Toke Høiland-Jørgensen [Tue, 5 Nov 2019 15:57:50 +0000 (16:57 +0100)]
net/fq_impl: Switch to kvmalloc() for memory allocation
[ Upstream commit
71e67c3bd127cfe7863f54e4b087eba1cc8f9a7a ]
The FQ implementation used by mac80211 allocates memory using kmalloc(),
which can fail; and Johannes reported that this actually happens in
practice.
To avoid this, switch the allocation to kvmalloc() instead; this also
brings fq_impl in line with all the FQ qdiscs.
Fixes:
557fc4a09803 ("fq: add fair queuing framework")
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191105155750.547379-1-toke@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jeff Layton [Thu, 7 Nov 2019 14:39:32 +0000 (09:39 -0500)]
ceph: return -EINVAL if given fsc mount option on kernel w/o support
[ Upstream commit
ff29fde84d1fc82f233c7da0daa3574a3942bec7 ]
If someone requests fscache on the mount, and the kernel doesn't
support it, it should fail the mount.
[ Drop ceph prefix -- it's provided by pr_err. ]
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vladimir Oltean [Tue, 5 Nov 2019 22:01:40 +0000 (00:01 +0200)]
net: mscc: ocelot: fix __ocelot_rmw_ix prototype
[ Upstream commit
17fdd7638cb687cd7f15a48545f25d738f0101e0 ]
The "read-modify-write register index" function is declared with a
confusing prototype: the "mask" and "reg" arguments are swapped.
Fortunately, this does not affect callers so far. Both arguments are
u32, and the wrapper macros (ocelot_rmw_ix etc) have the arguments in
the correct order (the one from ocelot_io.c).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Doug Berger [Tue, 5 Nov 2019 19:07:26 +0000 (11:07 -0800)]
net: bcmgenet: reapply manual settings to the PHY
[ Upstream commit
0686bd9d5e6863f60e4bb1e78e6fe7bb217a0890 ]
The phy_init_hw() function may reset the PHY to a configuration
that does not match manual network settings stored in the phydev
structure. If the phy state machine is polled rather than event
driven this can create a timing hazard where the phy state machine
might alter the settings stored in the phydev structure from the
value read from the BMCR.
This commit follows invocations of phy_init_hw() by the bcmgenet
driver with invocations of the genphy_config_aneg() function to
ensure that the BMCR is written to match the settings held in the
phydev structure. This prevents the risk of manual settings being
accidentally altered.
Fixes:
1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Doug Berger [Tue, 5 Nov 2019 19:07:24 +0000 (11:07 -0800)]
net: bcmgenet: use RGMII loopback for MAC reset
[ Upstream commit
3a55402c93877d291b0a612d25edb03d1b4b93ac ]
As noted in commit
28c2d1a7a0bf ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked while sw_reset
is asserted for its state machines to reset cleanly.
The transmit and receive clocks used by the UniMAC are derived from
the signals used on its PHY interface. The bcmgenet MAC can be
configured to work with different PHY interfaces including MII,
GMII, RGMII, and Reverse MII on internal and external interfaces.
Unfortunately for the UniMAC, when configured for MII the Tx clock
is always driven from the PHY which places it outside of the direct
control of the MAC.
The earlier commit enabled a local loopback mode within the UniMAC
so that the receive clock would be derived from the transmit clock
which addressed the observed issue with an external GPHY disabling
it's Rx clock. However, when a Tx clock is not available this
loopback is insufficient.
This commit implements a workaround that leverages the fact that
the MAC can reliably generate all of its necessary clocking by
enterring the external GPHY RGMII interface mode with the UniMAC in
local loopback during the sw_reset interval. Unfortunately, this
has the undesirable side efect of the RGMII GTXCLK signal being
driven during the same window.
In most configurations this is a benign side effect as the signal
is either not routed to a pin or is already expected to drive the
pin. The one exception is when an external MII PHY is expected to
drive the same pin with its TX_CLK output creating output driver
contention.
This commit exploits the IEEE 802.3 clause 22 standard defined
isolate mode to force an external MII PHY to present a high
impedance on its TX_CLK output during the window to prevent any
contention at the pin.
The MII interface is used internally with the 40nm internal EPHY
which agressively disables its clocks for power savings leading to
incomplete resets of the UniMAC and many instabilities observed
over the years. The workaround of this commit is expected to put
an end to those problems.
Fixes:
1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ilya Leoshkevich [Wed, 6 Nov 2019 05:17:06 +0000 (21:17 -0800)]
scripts/gdb: fix debugging modules compiled with hot/cold partitioning
[ Upstream commit
8731acc5068eb3f422a45c760d32198175c756f8 ]
gcc's -freorder-blocks-and-partition option makes it group frequently
and infrequently used code in .text.hot and .text.unlikely sections
respectively. At least when building modules on s390, this option is
used by default.
gdb assumes that all code is located in .text section, and that .text
section is located at module load address. With such modules this is no
longer the case: there is code in .text.hot and .text.unlikely, and
either of them might precede .text.
Fix by explicitly telling gdb the addresses of code sections.
It might be tempting to do this for all sections, not only the ones in
the white list. Unfortunately, gdb appears to have an issue, when
telling it about e.g. loadable .note.gnu.build-id section causes it to
think that non-loadable .note.Linux section is loaded at address 0,
which in turn causes NULL pointers to be resolved to bogus symbols. So
keep using the white list approach for the time being.
Link: http://lkml.kernel.org/r/20191028152734.13065-1-iii@linux.ibm.com
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Kieran Bingham <kbingham@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Olivier Moysan [Mon, 4 Nov 2019 13:36:54 +0000 (14:36 +0100)]
ASoC: stm32: sai: add restriction on mmap support
[ Upstream commit
eaf072e512d54c95b0977eda06cbca3151ace1e5 ]
Do not support mmap in S/PDIF mode. In S/PDIF mode
the buffer has to be copied, to allow the channel status
bits insertion.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20191104133654.28750-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Xingyu Chen [Sun, 29 Sep 2019 10:53:49 +0000 (18:53 +0800)]
watchdog: meson: Fix the wrong value of left time
[ Upstream commit
2c77734642d52448aca673e889b39f981110828b ]
The left time value is wrong when we get it by sysfs. The left time value
should be equal to preset timeout value minus elapsed time value. According
to the Meson-GXB/GXL datasheets which can be found at [0], the timeout value
is saved to BIT[0-15] of the WATCHDOG_TCNT, and elapsed time value is saved
to BIT[16-31] of the WATCHDOG_TCNT.
[0]: http://linux-meson.com
Fixes:
683fa50f0e18 ("watchdog: Add Meson GXBB Watchdog Driver")
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Timo Schlüßler [Fri, 11 Oct 2019 13:38:19 +0000 (15:38 +0200)]
can: mcp251x: mcp251x_restart_work_handler(): Fix potential force_quit race condition
[ Upstream commit
27a0e54bae09d2dd023a01254db506d61cc50ba1 ]
In mcp251x_restart_work_handler() the variable to stop the interrupt
handler (priv->force_quit) is reset after the chip is restarted and thus
a interrupt might occur.
This patch fixes the potential race condition by resetting force_quit
before enabling interrupts.
Signed-off-by: Timo Schlüßler <schluessler@krause.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marc Kleine-Budde [Mon, 15 Jul 2019 18:53:08 +0000 (20:53 +0200)]
can: flexcan: increase error counters if skb enqueueing via can_rx_offload_queue_sorted() fails
[ Upstream commit
758124335a9dd649ab820bfb5b328170919ee7dc ]
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marc Kleine-Budde [Tue, 24 Sep 2019 18:45:38 +0000 (18:45 +0000)]
can: rx-offload: can_rx_offload_irq_offload_fifo(): continue on error
[ Upstream commit
1f7f504dcd9d1262437bdcf4fa071e41dec1af03 ]
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
If the hardware FIFO is empty can_rx_offload_offload_one() will return
NULL.
In case a CAN frame was read from the hardware,
can_rx_offload_offload_one() returns the skb containing it.
Without this patch can_rx_offload_irq_offload_fifo() bails out if no skb
returned, regardless of the reason.
Similar to can_rx_offload_irq_offload_timestamp() in case of a resource
shortage the whole FIFO should be discarded, to avoid an IRQ storm and
give the system some time to recover. However if the FIFO is empty the
loop can be left.
With this patch the loop is left in case of empty FIFO, but not on
errors.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jeroen Hofstee [Tue, 24 Sep 2019 18:45:38 +0000 (18:45 +0000)]
can: rx-offload: can_rx_offload_irq_offload_timestamp(): continue on error
[ Upstream commit
c2a9f74c9d18acfdcabd3361adc7eac82c537a66 ]
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
However can_rx_offload_irq_offload_timestamp() bails out in the error
case. In case of a resource shortage all mailboxes should be discarded,
to avoid an IRQ storm and give the system some time to recover.
Since can_rx_offload_irq_offload_timestamp() is typically called from a
while loop, all message will eventually be discarded. So let's continue
on error instead to discard them directly.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marc Kleine-Budde [Wed, 9 Oct 2019 19:00:32 +0000 (21:00 +0200)]
can: rx-offload: can_rx_offload_offload_one(): use ERR_PTR() to propagate error value in case of errors
[ Upstream commit
d763ab3044f0bf50bd0e6179f6b2cf1c125d1d94 ]
Before this patch can_rx_offload_offload_one() returns a pointer to a
skb containing the read CAN frame or a NULL pointer.
However the meaning of the NULL pointer is ambiguous, it can either mean
the requested mailbox is empty or there was an error.
This patch fixes this situation by returning:
- pointer to skb on success
- NULL pointer if mailbox is empty
- ERR_PTR() in case of an error
All users of can_rx_offload_offload_one() have been adopted, no
functional change intended.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marc Kleine-Budde [Wed, 9 Oct 2019 13:15:07 +0000 (15:15 +0200)]
can: rx-offload: can_rx_offload_offload_one(): increment rx_fifo_errors on queue overflow or OOM
[ Upstream commit
4e9016bee3bf0c24963097edace034ff205b565c ]
If the rx-offload skb_queue is full or the skb allocation fails (due to OOM),
the mailbox contents is discarded.
This patch adds the incrementing of the rx_fifo_errors statistics counter.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marc Kleine-Budde [Wed, 9 Oct 2019 14:03:18 +0000 (16:03 +0200)]
can: rx-offload: can_rx_offload_offload_one(): do not increase the skb_queue beyond skb_queue_len_max
[ Upstream commit
a2dc3f5e1022a5ede8af9ab89a144f1e69db8636 ]
The skb_queue is a linked list, holding the skb to be processed in the
next NAPI call.
Without this patch, the queue length in can_rx_offload_offload_one() is
limited to skb_queue_len_max + 1. As the skb_queue is a linked list, no
array or other resources are accessed out-of-bound, however this
behaviour is counterintuitive.
This patch limits the rx-offload skb_queue length to skb_queue_len_max.
Fixes:
d254586c3453 ("can: rx-offload: Add support for HW fifo based irq offloading")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marc Kleine-Budde [Wed, 9 Oct 2019 13:48:48 +0000 (15:48 +0200)]
can: rx-offload: can_rx_offload_queue_tail(): fix error handling, avoid skb mem leak
[ Upstream commit
6caf8a6d6586d44fd72f4aa1021d14aa82affafb ]
If the rx-offload skb_queue is full can_rx_offload_queue_tail() will not
queue the skb and return with an error.
This patch frees the skb in case of a full queue, which brings
can_rx_offload_queue_tail() in line with the
can_rx_offload_queue_sorted() function, which has been adjusted in the
previous patch.
The return value is adjusted to -ENOBUFS to better reflect the actual
problem.
The device stats handling is left to the caller.
Fixes:
d254586c3453 ("can: rx-offload: Add support for HW fifo based irq offloading")
Reported-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jeroen Hofstee [Tue, 1 Oct 2019 21:01:20 +0000 (21:01 +0000)]
can: c_can: D_CAN: c_can_chip_config(): perform a sofware reset on open
[ Upstream commit
23c5a9488f076bab336177cd1d1a366bd8ddf087 ]
When the CAN interface is closed it the hardwre is put in power down
mode, but does not reset the error counters / state. Reset the D_CAN on
open, so the reported state and the actual state match.
According to [1], the C_CAN module doesn't have the software reset.
[1] http://www.bosch-semiconductors.com/media/ip_modules/pdf_2/c_can_fd8/users_manual_c_can_fd8_r210_1.pdf
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jeroen Hofstee [Wed, 25 Sep 2019 08:58:45 +0000 (08:58 +0000)]
can: peak_usb: report bus recovery as well
[ Upstream commit
128a1b87d3ceb2ba449d5aadb222fe22395adeb0 ]
While the state changes are reported when the error counters increase
and decrease, there is no event when the bus recovers and the error
counters decrease again. So add those as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Florian Westphal [Sun, 3 Nov 2019 19:54:28 +0000 (20:54 +0100)]
bridge: ebtables: don't crash when using dnat target in output chains
[ Upstream commit
b23c0742c2ce7e33ed79d10e451f70fdb5ca85d1 ]
xt_in() returns NULL in the output hook, skip the pkt_type change for
that case, redirection only makes sense in broute/prerouting hooks.
Reported-by: Tom Yan <tom.ty89@gmail.com>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Fixes:
cf3cb246e277d ("bridge: ebtables: fix reception of frames DNAT-ed to bridge device/port")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Chuhong Yuan [Mon, 4 Nov 2019 15:50:00 +0000 (23:50 +0800)]
net: fec: add missed clk_disable_unprepare in remove
[ Upstream commit
c43eab3eddb4c6742ac20138659a9b701822b274 ]
This driver forgets to disable and unprepare clks when remove.
Add calls to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tony Lindgren [Mon, 30 Sep 2019 15:40:01 +0000 (08:40 -0700)]
clk: ti: clkctrl: Fix failed to enable error with double udelay timeout
[ Upstream commit
81a41901ffd46bac6df4c95b8290ac259e0feda8 ]
Commit
3d8598fb9c5a ("clk: ti: clkctrl: use fallback udelay approach if
timekeeping is suspended") added handling for cases when timekeeping is
suspended. But looks like we can still get occasional "failed to enable"
errors on the PM runtime resume path with udelay() returning faster than
expected.
With ti-sysc interconnect target module driver this leads into device
failure with PM runtime failing with "failed to enable" clkctrl error.
Let's fix the issue with a delay of two times the desired delay as in
often done for udelay() to account for the inaccuracy.
Fixes:
3d8598fb9c5a ("clk: ti: clkctrl: use fallback udelay approach if timekeeping is suspended")
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lkml.kernel.org/r/20190930154001.46581-1-tony@atomide.com
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Peter Ujfalusi [Wed, 2 Oct 2019 08:34:36 +0000 (11:34 +0300)]
clk: ti: dra7-atl-clock: Remove ti_clk_add_alias call
[ Upstream commit
9982b0f69b49931b652d35f86f519be2ccfc7027 ]
ti_clk_register() calls it already so the driver should not create
duplicated alias.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lkml.kernel.org/r/20191002083436.10194-1-peter.ujfalusi@ti.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Xiaochen Shen [Tue, 29 Oct 2019 05:25:02 +0000 (13:25 +0800)]
x86/resctrl: Prevent NULL pointer dereference when reading mondata
[ Upstream commit
26467b0f8407cbd628fa5b7bcfd156e772004155 ]
When a mon group is being deleted, rdtgrp->flags is set to RDT_DELETED
in rdtgroup_rmdir_mon() firstly. The structure of rdtgrp will be freed
until rdtgrp->waitcount is dropped to 0 in rdtgroup_kn_unlock() later.
During the window of deleting a mon group, if an application calls
rdtgroup_mondata_show() to read mondata under this mon group,
'rdtgrp' returned from rdtgroup_kn_lock_live() is a NULL pointer when
rdtgrp->flags is RDT_DELETED. And then 'rdtgrp' is passed in this path:
rdtgroup_mondata_show() --> mon_event_read() --> mon_event_count().
Thus it results in NULL pointer dereference in mon_event_count().
Check 'rdtgrp' in rdtgroup_mondata_show(), and return -ENOENT
immediately when reading mondata during the window of deleting a mon
group.
Fixes:
d89b7379015f ("x86/intel_rdt/cqm: Add mon_data")
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: pei.p.jia@intel.com
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/1572326702-27577-1-git-send-email-xiaochen.shen@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Matthew Wilcox (Oracle) [Sat, 2 Nov 2019 04:25:08 +0000 (00:25 -0400)]
idr: Fix idr_alloc_u32 on 32-bit systems
[ Upstream commit
b7e9728f3d7fc5c5c8508d99f1675212af5cfd49 ]
Attempting to allocate an entry at 0xffffffff when one is already
present would succeed in allocating one at 2^32, which would confuse
everything. Return -ENOSPC in this case, as expected.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Matthew Wilcox (Oracle) [Sun, 3 Nov 2019 11:36:43 +0000 (06:36 -0500)]
idr: Fix integer overflow in idr_for_each_entry
[ Upstream commit
f6341c5af4e6e15041be39976d16deca789555fa ]
If there is an entry at INT_MAX then idr_for_each_entry() will increment
id after handling it. This is undefined behaviour, and is caught by
UBSAN. Adding 1U to id forces the operation to be carried out as an
unsigned addition which (when assigned to id) will result in INT_MIN.
Since there is never an entry stored at INT_MIN, idr_get_next() will
return NULL, ending the loop as expected.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Eric Dumazet [Fri, 1 Nov 2019 03:34:44 +0000 (20:34 -0700)]
powerpc/bpf: Fix tail call implementation
[ Upstream commit
7de086909365cd60a5619a45af3f4152516fd75c ]
We have seen many crashes on powerpc hosts while loading bpf programs.
The problem here is that bpf_int_jit_compile() does a first pass
to compute the program length.
Then it allocates memory to store the generated program and
calls bpf_jit_build_body() a second time (and a third time
later)
What I have observed is that the second bpf_jit_build_body()
could end up using few more words than expected.
If bpf_jit_binary_alloc() put the space for the program
at the end of the allocated page, we then write on
a non mapped memory.
It appears that bpf_jit_emit_tail_call() calls
bpf_jit_emit_common_epilogue() while ctx->seen might not
be stable.
Only after the second pass we can be sure ctx->seen wont be changed.
Trying to avoid a second pass seems quite complex and probably
not worth it.
Fixes:
ce0761419faef ("powerpc/bpf: Implement support for tail calls")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Sandipan Das <sandipan@linux.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20191101033444.143741-1-edumazet@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Björn Töpel [Tue, 1 Oct 2019 11:33:07 +0000 (13:33 +0200)]
samples/bpf: fix build by setting HAVE_ATTR_TEST to zero
[ Upstream commit
04ec044b7d30800296824783df7d9728d16d7567 ]
To remove that test_attr__{enabled/open} are used by perf-sys.h, we
set HAVE_ATTR_TEST to zero.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: KP Singh <kpsingh@google.com>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: bpf@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: http://lore.kernel.org/bpf/20191001113307.27796-3-bjorn.topel@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ondrej Jirman [Mon, 28 Oct 2019 21:58:58 +0000 (22:58 +0100)]
ARM: dts: sun8i-a83t-tbs-a711: Fix WiFi resume from suspend
[ Upstream commit
e614f341253f8541baf0230a8dc6a016b544b1e2 ]
Without enabling keep-power-in-suspend, we can't wake the device
up using WOL packet, and the log is flooded with these messages
on resume:
sunxi-mmc
1c10000.mmc: send stop command failed
sunxi-mmc
1c10000.mmc: data error, sending stop command
sunxi-mmc
1c10000.mmc: send stop command failed
sunxi-mmc
1c10000.mmc: data error, sending stop command
So to make the WiFi really a wakeup-source, we need to keep it powered
during suspend.
Fixes:
0e23372080def7 ("arm: dts: sun8i: Add the TBS A711 tablet devicetree")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Colin Ian King [Wed, 23 Oct 2019 11:28:09 +0000 (12:28 +0100)]
clk: sunxi-ng: a80: fix the zero'ing of bits 16 and 18
[ Upstream commit
cdfc2e2086bf9c465f44e2db25561373b084a113 ]
The zero'ing of bits 16 and 18 is incorrect. Currently the code
is masking with the bitwise-and of BIT(16) & BIT(18) which is
0, so the updated value for val is always zero. Fix this by bitwise
and-ing value with the correct mask that will zero bits 16 and 18.
Addresses-Coverity: (" Suspicious &= or |= constant expression")
Fixes:
b8eb71dcdd08 ("clk: sunxi-ng: Add A80 CCU")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nathan Chancellor [Tue, 22 Oct 2019 16:50:54 +0000 (09:50 -0700)]
clk: sunxi: Fix operator precedence in sunxi_divs_clk_setup
[ Upstream commit
afdc74ed2d57e86c10b1d6831339770a802bab9a ]
r375326 in Clang exposes an issue with operator precedence in
sunxi_div_clk_setup:
drivers/clk/sunxi/clk-sunxi.c:1083:30: warning: operator '?:' has lower
precedence than '|'; '|' will be evaluated first
[-Wbitwise-conditional-parentheses]
data->div[i].critical ?
~~~~~~~~~~~~~~~~~~~~~ ^
drivers/clk/sunxi/clk-sunxi.c:1083:30: note: place parentheses around
the '|' expression to silence this warning
data->div[i].critical ?
^
)
drivers/clk/sunxi/clk-sunxi.c:1083:30: note: place parentheses around
the '?:' expression to evaluate it first
data->div[i].critical ?
^
(
1 warning generated.
It appears that the intention was for ?: to be evaluated first so that
CLK_IS_CRITICAL could be added to clkflags if the critical boolean was
set; right now, | is being evaluated first. Add parentheses around the
?: block to have it be evaluated first.
Fixes:
9919d44ff297 ("clk: sunxi: Use CLK_IS_CRITICAL flag for critical clks")
Link: https://github.com/ClangBuiltLinux/linux/issues/745
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Alexandre Belloni [Fri, 20 Sep 2019 15:39:06 +0000 (17:39 +0200)]
clk: at91: avoid sleeping early
[ Upstream commit
658fd65cf0b0d511de1718e48d9a28844c385ae0 ]
It is not allowed to sleep to early in the boot process and this may lead
to kernel issues if the bootloader didn't prepare the slow clock and main
clock.
This results in the following error and dump stack on the AriettaG25:
bad: scheduling from the idle thread!
Ensure it is possible to sleep, else simply have a delay.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lkml.kernel.org/r/20190920153906.20887-1-alexandre.belloni@bootlin.com
Fixes:
80eded6ce8bb ("clk: at91: add slow clks driver")
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Randy Dunlap [Wed, 23 Oct 2019 03:57:06 +0000 (20:57 -0700)]
reset: fix reset_control_ops kerneldoc comment
[ Upstream commit
f430c7ed8bc22992ed528b518da465b060b9223f ]
Add a missing short description to the reset_control_ops documentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
[p.zabel@pengutronix.de: rebased and updated commit message]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabio Estevam [Wed, 9 Oct 2019 20:43:43 +0000 (17:43 -0300)]
ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts
[ Upstream commit
7e5d0bf6afcc7bd72f78e7f33570e2e0945624f0 ]
Since commit
a211b8c55f3c ("ARM: dts: imx6qdl-sabreauto: Add sensors")
a storm of accelerometer interrupts is seen:
[ 114.211283] irq 260: nobody cared (try booting with the "irqpoll" option)
[ 114.218108] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.4 #1
[ 114.223960] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 114.230531] [<
c0112858>] (unwind_backtrace) from [<
c010cdc8>] (show_stack+0x10/0x14)
[ 114.238301] [<
c010cdc8>] (show_stack) from [<
c0c1aa1c>] (dump_stack+0xd8/0x110)
[ 114.245644] [<
c0c1aa1c>] (dump_stack) from [<
c0193594>] (__report_bad_irq+0x30/0xc0)
[ 114.253417] [<
c0193594>] (__report_bad_irq) from [<
c01933ac>] (note_interrupt+0x108/0x298)
[ 114.261707] [<
c01933ac>] (note_interrupt) from [<
c018ffe4>] (handle_irq_event_percpu+0x70/0x80)
[ 114.270433] [<
c018ffe4>] (handle_irq_event_percpu) from [<
c019002c>] (handle_irq_event+0x38/0x5c)
[ 114.279326] [<
c019002c>] (handle_irq_event) from [<
c019438c>] (handle_level_irq+0xc8/0x154)
[ 114.287701] [<
c019438c>] (handle_level_irq) from [<
c018eda0>] (generic_handle_irq+0x20/0x34)
[ 114.296166] [<
c018eda0>] (generic_handle_irq) from [<
c0534214>] (mxc_gpio_irq_handler+0x30/0xf0)
[ 114.304975] [<
c0534214>] (mxc_gpio_irq_handler) from [<
c0534334>] (mx3_gpio_irq_handler+0x60/0xb0)
[ 114.313955] [<
c0534334>] (mx3_gpio_irq_handler) from [<
c018eda0>] (generic_handle_irq+0x20/0x34)
[ 114.322762] [<
c018eda0>] (generic_handle_irq) from [<
c018f3ac>] (__handle_domain_irq+0x64/0xe0)
[ 114.331485] [<
c018f3ac>] (__handle_domain_irq) from [<
c05215a8>] (gic_handle_irq+0x4c/0xa8)
[ 114.339862] [<
c05215a8>] (gic_handle_irq) from [<
c0101a70>] (__irq_svc+0x70/0x98)
[ 114.347361] Exception stack(0xc1301ec0 to 0xc1301f08)
[ 114.352435] 1ec0:
00000001 00000006 00000000 c130c340 00000001 c130f688 9785636d c13ea2e8
[ 114.360635] 1ee0:
9784907d 0000001a eaf99d78 0000001a 00000000 c1301f10 c0182b00 c0878de4
[ 114.368830] 1f00:
20000013 ffffffff
[ 114.372349] [<
c0101a70>] (__irq_svc) from [<
c0878de4>] (cpuidle_enter_state+0x168/0x5f4)
[ 114.380464] [<
c0878de4>] (cpuidle_enter_state) from [<
c08792ac>] (cpuidle_enter+0x28/0x38)
[ 114.388751] [<
c08792ac>] (cpuidle_enter) from [<
c015ef9c>] (do_idle+0x224/0x2a8)
[ 114.396168] [<
c015ef9c>] (do_idle) from [<
c015f3b8>] (cpu_startup_entry+0x18/0x20)
[ 114.403765] [<
c015f3b8>] (cpu_startup_entry) from [<
c1200e54>] (start_kernel+0x43c/0x500)
[ 114.411958] handlers:
[ 114.414302] [<
a01028b8>] irq_default_primary_handler threaded [<
fd7a3b08>] mma8452_interrupt
[ 114.422974] Disabling IRQ #260
CPU0 CPU1
....
260: 100001 0 gpio-mxc 31 Level mma8451
The MMA8451 interrupt triggers as low level, so the GPIO6_IO31 pin
needs to activate its pull up, otherwise it will stay always at low level
generating multiple interrupts.
The current device tree does not configure the IOMUX for this pin, so
it uses whathever comes configured from the bootloader.
The IOMUXC_SW_PAD_CTL_PAD_EIM_BCLK register value comes as 0x8000 from
the bootloader, which has PKE bit cleared, hence disabling the
pull-up.
Instead of relying on a previous configuration from the bootloader,
configure the GPIO6_IO31 pin with pull-up enabled in order to fix
this problem.
Fixes:
a211b8c55f3c ("ARM: dts: imx6qdl-sabreauto: Add sensors")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-By: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Andy Shevchenko [Thu, 24 Oct 2019 13:34:41 +0000 (16:34 +0300)]
pinctrl: cherryview: Allocate IRQ chip dynamic
[ Upstream commit
67d33aecd030226f0a577eb683aaa6853ecf8f91 ]
Keeping the IRQ chip definition static shares it with multiple instances
of the GPIO chip in the system. This is bad and now we get this warning
from GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
This patch is heavily based on the attachment to the bug by Christoph Marz.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=202543
Fixes:
6e08d6bbebeb ("pinctrl: Add Intel Cherryview/Braswell pin controller support")
Depends-on:
83b9dc11312f ("pinctrl: cherryview: Associate IRQ descriptors to irqdomain")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marek Szyprowski [Fri, 25 Oct 2019 09:02:01 +0000 (11:02 +0200)]
clk: samsung: exynos5420: Preserve PLL configuration during suspend/resume
[ Upstream commit
e9323b664ce29547d996195e8a6129a351c39108 ]
Properly save and restore all top PLL related configuration registers
during suspend/resume cycle. So far driver only handled EPLL and RPLL
clocks, all other were reset to default values after suspend/resume cycle.
This caused for example lower G3D (MALI Panfrost) performance after system
resume, even if performance governor has been selected.
Reported-by: Reported-by: Marian Mihailescu <mihailescu2m@gmail.com>
Fixes:
773424326b51 ("clk: samsung: exynos5420: add more registers to restore list")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Russell King [Wed, 23 Oct 2019 13:46:49 +0000 (14:46 +0100)]
ASoC: kirkwood: fix device remove ordering
[ Upstream commit
dc39596a906d5b604f4e64597b6e904fc14625e8 ]
The devm conversion of kirkwood was incorrect; on removal, devm takes
effect after the "remove" function has returned. So, the effect of
the conversion was to change the order during remove from:
- snd_soc_unregister_component() (unpublishes interfaces)
- clk_disable_unprepare()
- cleanup resources
After the conversion, this became:
- clk_disable_unprepare() - while the device may still be active
- snd_soc_unregister_component()
- cleanup resources
Hence, it introduces a bug, where the internal clock for the device
may be shut down before the device itself has been shut down. It is
known that Marvell SoCs, including Dove, locks up if registers for a
peripheral that has its clocks disabled are accessed.
Fixes:
f98fc0f8154e ("ASoC: kirkwood: replace platform to component")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1iNGyP-0004oN-BA@rmk-PC.armlinux.org.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Russell King [Wed, 23 Oct 2019 13:46:44 +0000 (14:46 +0100)]
ASoC: kirkwood: fix external clock probe defer
[ Upstream commit
4523817d51bc3b2ef38da768d004fda2c8bc41de ]
When our call to get the external clock fails, we forget to clean up
the enabled internal clock correctly. Enable the clock after we have
obtained all our resources.
Fixes:
84aac6c79bfd ("ASoC: kirkwood: fix loss of external clock at probe time")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1iNGyK-0004oF-6A@rmk-PC.armlinux.org.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marek Szyprowski [Wed, 2 Oct 2019 08:53:09 +0000 (10:53 +0200)]
clk: samsung: exynos5433: Fix error paths
[ Upstream commit
faac3604d05e8015567124e5ee79edc3f1568a89 ]
Add checking the value returned by samsung_clk_alloc_reg_dump() and
devm_kcalloc(). While fixing this, also release all gathered clocks.
Fixes:
523d3de41f02 ("clk: samsung: exynos5433: Add support for runtime PM")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
[s.nawrocki: squashed patch from K. Kozlowski adding missing slab.h header]
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kishon Vijay Abraham I [Tue, 22 Oct 2019 08:36:23 +0000 (14:06 +0530)]
reset: Fix memory leak in reset_control_array_put()
[ Upstream commit
532f9cd6ee994ed10403e856ca27501428048597 ]
Memory allocated for 'struct reset_control_array' in
of_reset_control_array_get() is never freed in
reset_control_array_put() resulting in kmemleak showing
the following backtrace.
backtrace:
[<
00000000c5f17595>] __kmalloc+0x1b0/0x2b0
[<
00000000bd499e13>] of_reset_control_array_get+0xa4/0x180
[<
000000004cc02754>] 0xffff800008c669e4
[<
0000000050a83b24>] platform_drv_probe+0x50/0xa0
[<
00000000d3a0b0bc>] really_probe+0x108/0x348
[<
000000005aa458ac>] driver_probe_device+0x58/0x100
[<
000000008853626c>] device_driver_attach+0x6c/0x90
[<
0000000085308d19>] __driver_attach+0x84/0xc8
[<
00000000080d35f2>] bus_for_each_dev+0x74/0xc8
[<
00000000dd7f015b>] driver_attach+0x20/0x28
[<
00000000923ba6e6>] bus_add_driver+0x148/0x1f0
[<
0000000061473b66>] driver_register+0x60/0x110
[<
00000000c5bec167>] __platform_driver_register+0x40/0x48
[<
000000007c764b4f>] 0xffff800008c6c020
[<
0000000047ec2e8c>] do_one_initcall+0x5c/0x1b0
[<
0000000093d4b50d>] do_init_module+0x54/0x1d0
Fixes:
17c82e206d2a ("reset: Add APIs to manage array of resets")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Xiaojun Sang [Mon, 21 Oct 2019 09:54:32 +0000 (10:54 +0100)]
ASoC: compress: fix unsigned integer overflow check
[ Upstream commit
d3645b055399538415586ebaacaedebc1e5899b0 ]
Parameter fragments and fragment_size are type of u32. U32_MAX is
the correct check.
Signed-off-by: Xiaojun Sang <xsang@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191021095432.5639-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Stephan Gerhold [Sun, 20 Oct 2019 15:30:06 +0000 (17:30 +0200)]
ASoC: msm8916-wcd-analog: Fix RX1 selection in RDAC2 MUX
[ Upstream commit
9110d1b0e229cebb1ffce0c04db2b22beffd513d ]
According to the PM8916 Hardware Register Description,
CDC_D_CDC_CONN_HPHR_DAC_CTL has only a single bit (RX_SEL)
to switch between RX1 (0) and RX2 (1). It is not possible to
disable it entirely to achieve the "ZERO" state.
However, at the moment the "RDAC2 MUX" mixer defines three possible
values ("ZERO", "RX2" and "RX1"). Setting the mixer to "ZERO"
actually configures it to RX1. Setting the mixer to "RX1" has
(seemingly) no effect.
Remove "ZERO" and replace it with "RX1" to fix this.
Fixes:
585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20191020153007.206070-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabien Parent [Thu, 19 Sep 2019 19:13:15 +0000 (21:13 +0200)]
clocksource/drivers/mediatek: Fix error handling
[ Upstream commit
41d49e7939de5ec532d86494185b2ca2e99c848a ]
When timer_of_init fails, it cleans up after itself by undoing
everything it did during the initialization function.
mtk_syst_init and mtk_gpt_init both call timer_of_cleanup if
timer_of_init fails. timer_of_cleanup try to release the resource
taken. Since these resources have already been cleaned up by
timer_of_init, we end up getting a few warnings printed:
[ 0.001935] WARNING: CPU: 0 PID: 0 at __clk_put+0xe8/0x128
[ 0.002650] Modules linked in:
[ 0.003058] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.67+ #1
[ 0.003852] Hardware name: MediaTek MT8183 (DT)
[ 0.004446] pstate:
20400085 (nzCv daIf +PAN -UAO)
[ 0.005073] pc : __clk_put+0xe8/0x128
[ 0.005555] lr : clk_put+0xc/0x14
[ 0.005988] sp :
ffffff80090b3ea0
[ 0.006422] x29:
ffffff80090b3ea0 x28:
0000000040e20018
[ 0.007121] x27:
ffffffc07bfff780 x26:
0000000000000001
[ 0.007819] x25:
ffffff80090bda80 x24:
ffffff8008ec5828
[ 0.008517] x23:
ffffff80090bd000 x22:
ffffff8008d8b2e8
[ 0.009216] x21:
0000000000000001 x20:
fffffffffffffdfb
[ 0.009914] x19:
ffffff8009166180 x18:
00000000002bffa8
[ 0.010612] x17:
ffffffc012996980 x16:
0000000000000000
[ 0.011311] x15:
ffffffbf004a6800 x14:
3536343038393334
[ 0.012009] x13:
2079726576652073 x12:
7eb9c62c5c38f100
[ 0.012707] x11:
ffffff80090b3ba0 x10:
ffffff80090b3ba0
[ 0.013405] x9 :
0000000000000004 x8 :
0000000000000040
[ 0.014103] x7 :
ffffffc079400270 x6 :
0000000000000000
[ 0.014801] x5 :
ffffffc079400248 x4 :
0000000000000000
[ 0.015499] x3 :
0000000000000000 x2 :
0000000000000000
[ 0.016197] x1 :
ffffff80091661c0 x0 :
fffffffffffffdfb
[ 0.016896] Call trace:
[ 0.017218] __clk_put+0xe8/0x128
[ 0.017654] clk_put+0xc/0x14
[ 0.018048] timer_of_cleanup+0x60/0x7c
[ 0.018551] mtk_syst_init+0x8c/0x9c
[ 0.019020] timer_probe+0x6c/0xe0
[ 0.019469] time_init+0x14/0x44
[ 0.019893] start_kernel+0x2d0/0x46c
[ 0.020378] ---[ end trace
8c1efabea1267649 ]---
[ 0.020982] ------------[ cut here ]------------
[ 0.021586] Trying to vfree() nonexistent vm area ((____ptrval____))
[ 0.022427] WARNING: CPU: 0 PID: 0 at __vunmap+0xd0/0xd8
[ 0.023119] Modules linked in:
[ 0.023524] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 4.19.67+ #1
[ 0.024498] Hardware name: MediaTek MT8183 (DT)
[ 0.025091] pstate:
60400085 (nZCv daIf +PAN -UAO)
[ 0.025718] pc : __vunmap+0xd0/0xd8
[ 0.026176] lr : __vunmap+0xd0/0xd8
[ 0.026632] sp :
ffffff80090b3e90
[ 0.027066] x29:
ffffff80090b3e90 x28:
0000000040e20018
[ 0.027764] x27:
ffffffc07bfff780 x26:
0000000000000001
[ 0.028462] x25:
ffffff80090bda80 x24:
ffffff8008ec5828
[ 0.029160] x23:
ffffff80090bd000 x22:
ffffff8008d8b2e8
[ 0.029858] x21:
0000000000000000 x20:
0000000000000000
[ 0.030556] x19:
ffffff800800d000 x18:
00000000002bffa8
[ 0.031254] x17:
0000000000000000 x16:
0000000000000000
[ 0.031952] x15:
ffffffbf004a6800 x14:
3536343038393334
[ 0.032651] x13:
2079726576652073 x12:
7eb9c62c5c38f100
[ 0.033349] x11:
ffffff80090b3b40 x10:
ffffff80090b3b40
[ 0.034047] x9 :
0000000000000005 x8 :
5f5f6c6176727470
[ 0.034745] x7 :
5f5f5f5f28282061 x6 :
ffffff80091c86ef
[ 0.035443] x5 :
ffffff800852b690 x4 :
0000000000000000
[ 0.036141] x3 :
0000000000000002 x2 :
0000000000000002
[ 0.036839] x1 :
7eb9c62c5c38f100 x0 :
7eb9c62c5c38f100
[ 0.037536] Call trace:
[ 0.037859] __vunmap+0xd0/0xd8
[ 0.038271] vunmap+0x24/0x30
[ 0.038664] __iounmap+0x2c/0x34
[ 0.039088] timer_of_cleanup+0x70/0x7c
[ 0.039591] mtk_syst_init+0x8c/0x9c
[ 0.040060] timer_probe+0x6c/0xe0
[ 0.040507] time_init+0x14/0x44
[ 0.040932] start_kernel+0x2d0/0x46c
This commit remove the calls to timer_of_cleanup when timer_of_init
fails since it is unnecessary and actually cause warnings to be printed.
Fixes:
a0858f937960 ("mediatek: Convert the driver to timer-of")
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/linux-arm-kernel/20190919191315.25190-1-fparent@baylibre.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
Martin Blumenstingl [Sat, 21 Sep 2019 15:04:11 +0000 (17:04 +0200)]
clk: meson: gxbb: let sar_adc_clk_div set the parent clock rate
[ Upstream commit
44b09b11b813b8550e6b976ea51593bc23bba8d1 ]
The meson-saradc driver manually sets the input clock for
sar_adc_clk_sel. Update the GXBB clock driver (which is used on GXBB,
GXL and GXM) so the rate settings on sar_adc_clk_div are propagated up
to sar_adc_clk_sel which will let the common clock framework select the
best matching parent clock if we want that.
This makes sar_adc_clk_div consistent with the axg-aoclk and g12a-aoclk
drivers, which both also specify CLK_SET_RATE_PARENT.
Fixes:
33d0fcdfe0e870 ("clk: gxbb: add the SAR ADC clocks and expose them")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Greg Kroah-Hartman [Sun, 1 Dec 2019 08:17:47 +0000 (09:17 +0100)]
Linux 4.19.87
Ezequiel Garcia [Fri, 21 Jun 2019 21:39:49 +0000 (18:39 -0300)]
PM / devfreq: Fix kernel oops on governor module load
commit
7544fd7f384591038646d3cd9efb311ab4509e24 upstream.
A bit unexpectedly (but still documented), request_module may
return a positive value, in case of a modprobe error.
This is currently causing issues in the devfreq framework.
When a request_module exits with a positive value, we currently
return that via ERR_PTR. However, because the value is positive,
it's not a ERR_VALUE proper, and is therefore treated as a
valid struct devfreq_governor pointer, leading to a kernel oops.
Fix this by returning -EINVAL if request_module returns a positive
value.
Fixes:
b53b0128052ff ("PM / devfreq: Fix static checker warning in try_then_request_governor")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Ellerman [Wed, 13 Nov 2019 10:05:44 +0000 (21:05 +1100)]
KVM: PPC: Book3S HV: Flush link stack on guest exit to host kernel
commit
af2e8c68b9c5403f77096969c516f742f5bb29e0 upstream.
On some systems that are vulnerable to Spectre v2, it is up to
software to flush the link stack (return address stack), in order to
protect against Spectre-RSB.
When exiting from a guest we do some house keeping and then
potentially exit to C code which is several stack frames deep in the
host kernel. We will then execute a series of returns without
preceeding calls, opening up the possiblity that the guest could have
poisoned the link stack, and direct speculative execution of the host
to a gadget of some sort.
To prevent this we add a flush of the link stack on exit from a guest.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[dja: straightforward backport to v4.19]
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Ellerman [Wed, 13 Nov 2019 10:05:41 +0000 (21:05 +1100)]
powerpc/book3s64: Fix link stack flush on context switch
commit
39e72bf96f5847ba87cc5bd7a3ce0fed813dc9ad upstream.
In commit
ee13cb249fab ("powerpc/64s: Add support for software count
cache flush"), I added support for software to flush the count
cache (indirect branch cache) on context switch if firmware told us
that was the required mitigation for Spectre v2.
As part of that code we also added a software flush of the link
stack (return address stack), which protects against Spectre-RSB
between user processes.
That is all correct for CPUs that activate that mitigation, which is
currently Power9 Nimbus DD2.3.
What I got wrong is that on older CPUs, where firmware has disabled
the count cache, we also need to flush the link stack on context
switch.
To fix it we create a new feature bit which is not set by firmware,
which tells us we need to flush the link stack. We set that when
firmware tells us that either of the existing Spectre v2 mitigations
are enabled.
Then we adjust the patching code so that if we see that feature bit we
enable the link stack flush. If we're also told to flush the count
cache in software then we fall through and do that also.
On the older CPUs we don't need to do do the software count cache
flush, firmware has disabled it, so in that case we patch in an early
return after the link stack flush.
The naming of some of the functions is awkward after this patch,
because they're called "count cache" but they also do link stack. But
we'll fix that up in a later commit to ease backporting.
This is the fix for CVE-2019-18660.
Reported-by: Anthony Steinhauser <asteinhauser@google.com>
Fixes:
ee13cb249fab ("powerpc/64s: Add support for software count cache flush")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christopher M. Riedl [Fri, 24 May 2019 02:46:48 +0000 (21:46 -0500)]
powerpc/64s: support nospectre_v2 cmdline option
commit
d8f0e0b073e1ec52a05f0c2a56318b47387d2f10 upstream.
Add support for disabling the kernel implemented spectre v2 mitigation
(count cache flush on context switch) via the nospectre_v2 and
mitigations=off cmdline options.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Christopher M. Riedl <cmr@informatik.wtf>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190524024647.381-1-cmr@informatik.wtf
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bernd Porr [Mon, 18 Nov 2019 23:07:59 +0000 (23:07 +0000)]
staging: comedi: usbduxfast: usbduxfast_ai_cmdtest rounding error
commit
5618332e5b955b4bff06d0b88146b971c8dd7b32 upstream.
The userspace comedilib function 'get_cmd_generic_timed' fills
the cmd structure with an informed guess and then calls the
function 'usbduxfast_ai_cmdtest' in this driver repeatedly while
'usbduxfast_ai_cmdtest' is modifying the cmd struct until it
no longer changes. However, because of rounding errors this never
converged because 'steps = (cmd->convert_arg * 30) / 1000' and then
back to 'cmd->convert_arg = (steps * 1000) / 30' won't be the same
because of rounding errors. 'Steps' should only be converted back to
the 'convert_arg' if 'steps' has actually been modified. In addition
the case of steps being 0 wasn't checked which is also now done.
Signed-off-by: Bernd Porr <mail@berndporr.me.uk>
Cc: <stable@vger.kernel.org> # 4.4+
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20191118230759.1727-1-mail@berndporr.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aleksander Morgado [Wed, 13 Nov 2019 10:14:05 +0000 (11:14 +0100)]
USB: serial: option: add support for Foxconn T77W968 LTE modules
commit
f0797095423e6ea3b4be61134ee353c7f504d440 upstream.
These are the Foxconn-branded variants of the Dell DW5821e modules,
same USB layout as those. The device exposes AT, NMEA and DIAG ports
in both USB configurations.
P: Vendor=0489 ProdID=e0b4 Rev=03.18
S: Manufacturer=FII
S: Product=T77W968 LTE
S: SerialNumber=
0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
P: Vendor=0489 ProdID=e0b4 Rev=03.18
S: Manufacturer=FII
S: Product=T77W968 LTE
S: SerialNumber=
0123456789ABCDEF
C: #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
[ johan: drop id defines ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aleksander Morgado [Thu, 7 Nov 2019 10:55:08 +0000 (11:55 +0100)]
USB: serial: option: add support for DW5821e with eSIM support
commit
957c31ea082e3fe5196f46d5b04018b10de47400 upstream.
The device exposes AT, NMEA and DIAG ports in both USB configurations.
Exactly same layout as the default DW5821e module, just a different
vid/pid.
P: Vendor=413c ProdID=81e0 Rev=03.18
S: Manufacturer=Dell Inc.
S: Product=DW5821e-eSIM Snapdragon X20 LTE
S: SerialNumber=
0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
P: Vendor=413c ProdID=81e0 Rev=03.18
S: Manufacturer=Dell Inc.
S: Product=DW5821e-eSIM Snapdragon X20 LTE
S: SerialNumber=
0123456789ABCDEF
C: #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 7 Nov 2019 13:21:19 +0000 (14:21 +0100)]
USB: serial: mos7840: fix remote wakeup
commit
92fe35fb9c70a00d8fbbf5bd6172c921dd9c7815 upstream.
The driver was setting the device remote-wakeup feature during probe in
violation of the USB specification (which says it should only be set
just prior to suspending the device). This could potentially waste
power during suspend as well as lead to spurious wakeups.
Note that USB core would clear the remote-wakeup feature at first
resume.
Fixes:
3f5429746d91 ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 7 Nov 2019 13:21:18 +0000 (14:21 +0100)]
USB: serial: mos7720: fix remote wakeup
commit
ea422312a462696093b5db59d294439796cba4ad upstream.
The driver was setting the device remote-wakeup feature during probe in
violation of the USB specification (which says it should only be set
just prior to suspending the device). This could potentially waste
power during suspend as well as lead to spurious wakeups.
Note that USB core would clear the remote-wakeup feature at first
resume.
Fixes:
0f64478cbc7a ("USB: add USB serial mos7720 driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pavel Löbl [Fri, 1 Nov 2019 07:01:50 +0000 (08:01 +0100)]
USB: serial: mos7840: add USB ID to support Moxa UPort 2210
commit
e696d00e65e81d46e911f24b12e441037bf11b38 upstream.
Add USB ID for MOXA UPort 2210. This device contains mos7820 but
it passes GPIO0 check implemented by driver and it's detected as
mos7840. Hence product id check is added to force mos7820 mode.
Signed-off-by: Pavel Löbl <pavel@loebl.cz>
Cc: stable <stable@vger.kernel.org>
[ johan: rename id defines and add vendor-id check ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Neukum [Wed, 6 Nov 2019 12:49:01 +0000 (13:49 +0100)]
appledisplay: fix error handling in the scheduled work
commit
91feb01596e5efc0cc922cc73f5583114dccf4d2 upstream.
The work item can operate on
1. stale memory left over from the last transfer
the actual length of the data transfered needs to be checked
2. memory already freed
the error handling in appledisplay_probe() needs
to cancel the work in that case
Reported-and-tested-by: syzbot+495dab1f175edc9c2f13@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191106124902.7765-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Neukum [Thu, 7 Nov 2019 14:28:55 +0000 (15:28 +0100)]
USB: chaoskey: fix error case of a timeout
commit
92aa5986f4f7b5a8bf282ca0f50967f4326559f5 upstream.
In case of a timeout or if a signal aborts a read
communication with the device needs to be ended
lest we overwrite an active URB the next time we
do IO to the device, as the URB may still be active.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191107142856.16774-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Mon, 18 Nov 2019 09:21:19 +0000 (10:21 +0100)]
usb-serial: cp201x: support Mark-10 digital force gauge
commit
347bc8cb26388791c5881a3775cb14a3f765a674 upstream.
Add support for the Mark-10 digital force gauge device to the cp201x
driver.
Based on a report and a larger patch from Joel Jennings
Reported-by: Joel Jennings <joel.jennings@makeitlabs.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191118092119.GA153852@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suwan Kim [Mon, 11 Nov 2019 14:10:35 +0000 (23:10 +0900)]
usbip: Fix uninitialized symbol 'nents' in stub_recv_cmd_submit()
commit
2a9125317b247f2cf35c196f968906dcf062ae2d upstream.
Smatch reported that nents is not initialized and used in
stub_recv_cmd_submit(). nents is currently initialized by sgl_alloc()
and used to allocate multiple URBs when host controller doesn't
support scatter-gather DMA. The use of uninitialized nents means that
buf_len is zero and use_sg is true. But buffer length should not be
zero when an URB uses scatter-gather DMA.
To prevent this situation, add the conditional that checks buf_len
and use_sg. And move the use of nents right after the sgl_alloc() to
avoid the use of uninitialized nents.
If the error occurs, it adds SDEV_EVENT_ERROR_MALLOC and stub_priv
will be released by stub event handler and connection will be shut
down.
Fixes:
ea44d190764b ("usbip: Implement SG support to vhci-hcd and stub driver")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191111141035.27788-1-suwan.kim027@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>