OSDN Git Service
Maxime Ripard [Wed, 21 Feb 2018 12:57:02 +0000 (13:57 +0100)]
drm/sun4i: rgb: Fix potential division by zero
In the case where mode_valid callback of our RGB connector was called
before mode_set was being called, the range of dividers would not be set,
resulting in a division by zero later on in the clk_round_rate logic.
Set the range of dividers before calling clk_round_rate to fix this.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221125703.4595-2-maxime.ripard@bootlin.com
Maxime Ripard [Wed, 21 Feb 2018 12:57:01 +0000 (13:57 +0100)]
drm/sun4i: tcon: Reduce the scope of the LVDS error a bit
The current logic to deal with old DT missing the LVDS properties doesn't
take into account whether the LVDS output is supported in the first place,
resulting in spurious error messages on SoCs where it doesn't even matter.
Introduce a new TCON flag to list if LVDS is supported at all to prevent
this from happening.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221125703.4595-1-maxime.ripard@bootlin.com
Jernej Skrabec [Thu, 1 Mar 2018 21:34:32 +0000 (22:34 +0100)]
drm/sun4i: Release exclusive clock lock when disabling TCON
Currently exclusive TCON clock lock is never released, which, for
example, prevents changing resolution on HDMI.
In order to fix that, release clock when disabling TCON. TCON is always
disabled first before new mode is set.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180301213442.16677-7-jernej.skrabec@siol.net
Giulio Benetti [Wed, 28 Feb 2018 16:46:53 +0000 (17:46 +0100)]
drm/sun4i: Fix dclk_set_phase
Phase value is not shifted before writing.
Shift left of 28 bits to fit right bits
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1519836413-35023-1-git-send-email-giulio.benetti@micronovasrl.com
Dave Airlie [Wed, 21 Feb 2018 01:50:03 +0000 (11:50 +1000)]
virtio-gpu: fix ioctl and expose the fixed status to userspace.
This exposes to mesa that it can use the fixed ioctl for querying
later cap sets, cap set 1 is forever frozen in time.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180221015003.22884-1-airlied@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Maxime Ripard [Wed, 21 Feb 2018 09:20:27 +0000 (10:20 +0100)]
drm/sun4i: Protect the TCON pixel clocks
Both TCON clocks are very sensitive to clock changes, since any change
might lead to improper timings.
Make sure our rate is never changed.
Tested-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d5224d2e81ecf73dc09f234e580ada52c00eaee3.1519204731.git-series.maxime.ripard@bootlin.com
Ondrej Jirman [Thu, 22 Feb 2018 16:12:17 +0000 (17:12 +0100)]
drm/sun4i: Enable the output on the pins (tcon0)
I noticed that with 4.16-rc1 LVDS output on A83T based TBS A711 tablet doesn't
work (there's output but it's garbled). I compared some older patches for LVDS
support with the mainlined ones and this change is missing from mainline Linux.
I don't know what the register does exactly and the harcoded register value
doesn't inspire much confidence that it will work in a general case, so I'm
sending this RFC.
This patch fixes the issue on A83T.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222161217.23904-1-megous@megous.com
Ilia Mirkin [Sat, 3 Feb 2018 19:11:23 +0000 (14:11 -0500)]
drm/nouveau: prefer XBGR2101010 for addfb ioctl
Nouveau only exposes support for XBGR2101010. Prior to the atomic
conversion, drm would pass in the wrong format in the framebuffer, but
it was always ignored -- both userspace (xf86-video-nouveau) and the
kernel driver agreed on the layout, so the fact that the format was
wrong didn't matter.
With the atomic conversion, nouveau all of a sudden started caring about
the exact format, and so the previously-working code in
xf86-video-nouveau no longer functioned since the (internally-assigned)
format from the addfb ioctl was wrong.
This change adds infrastructure to allow a drm driver to specify that it
prefers the XBGR format variant for the addfb ioctl, and makes nouveau's
nv50 display driver set it. (Prior gens had no support for 30bpp at all.)
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: stable@vger.kernel.org # v4.10+
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203191123.31507-1-imirkin@alum.mit.edu
Dave Airlie [Wed, 21 Feb 2018 22:39:26 +0000 (08:39 +1000)]
Merge tag 'drm-misc-fixes-2018-02-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for 4.16. I contains fixes for deadlock on runtime suspend on few
drivers, a memory leak on non-blocking commits, a crash on color-eviction.
The is also meson and edid fixes, plus a fix for a doc warning.
* tag 'drm-misc-fixes-2018-02-21' of git://anongit.freedesktop.org/drm/drm-misc:
drm/tve200: fix kernel-doc documentation comment include
drm/meson: fix vsync buffer update
drm: Handle unexpected holes in color-eviction
drm/edid: Add 6 bpc quirk for CPT panel in Asus UX303LA
drm/amdgpu: Fix deadlock on runtime suspend
drm/radeon: Fix deadlock on runtime suspend
drm/nouveau: Fix deadlock on runtime suspend
drm: Allow determining if current task is output poll worker
workqueue: Allow retrieval of current task's work struct
drm/atomic: Fix memleak on ERESTARTSYS during non-blocking commits
Jani Nikula [Tue, 20 Feb 2018 14:20:08 +0000 (16:20 +0200)]
drm/tve200: fix kernel-doc documentation comment include
The DOC: line acts as an identifier for the :doc: include. Fixes:
./drivers/gpu/drm/tve200/tve200_drv.c:1: warning: no structured comments found
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220142008.9330-1-jani.nikula@intel.com
Philipp Zabel [Mon, 19 Feb 2018 17:59:38 +0000 (18:59 +0100)]
drm/edid: quirk Sony PlayStation VR headset as non-desktop
This uses the EDID info from the Sony PlayStation VR headset,
when connected directly, to mark it as non-desktop.
Since the connection box (product id b403) defaults to HDMI
pass-through to the TV, it is not marked as non-desktop.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Philipp Zabel [Mon, 19 Feb 2018 17:59:37 +0000 (18:59 +0100)]
drm/edid: quirk Windows Mixed Reality headsets as non-desktop
This uses the EDID info from Lenovo Explorer (LEN-b800), Acer AH100
(ACR-7fce), and Samsung Odyssey (SEC-144a) to mark them as non-desktop.
The other entries are for the HP Windows Mixed Reality Headset (HPN-3515),
the Fujitsu Windows Mixed Reality headset (FUJ-1970), the Dell Visor
(DEL-7fce), and the ASUS HC102 (AUS-c102). They are not tested with real
hardware, but listed as HMD monitors alongside the tested headsets in the
Microsoft HololensSensors driver package.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Philipp Zabel [Mon, 19 Feb 2018 17:59:36 +0000 (18:59 +0100)]
drm/edid: quirk Oculus Rift headsets as non-desktop
This uses the EDID info from Oculus Rift DK1 (OVR-0001), DK2 (OVR-0003),
and CV1 (OVR-0004) to mark them as non-desktop.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Tue, 20 Feb 2018 21:09:15 +0000 (07:09 +1000)]
Merge tag 'drm-misc-fixes-2018-01-31' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
- fix lut loading for cirrus
* tag 'drm-misc-fixes-2018-01-31' of git://anongit.freedesktop.org/drm/drm-misc:
drm/cirrus: Load lut in crtc_commit
Dave Airlie [Tue, 20 Feb 2018 21:08:22 +0000 (07:08 +1000)]
Merge tag 'exynos-drm-fixes-for-v4.16-rc3' of git://git./linux/kernel/git/daeinki/drm-exynos into drm-fixes
- three fixeups
. it fixes potential issues[1] by using monotonic timestamp
instead of 'struct timeval'
. correct HDMI_I2S_PIN_SEL_1 definition and setting value.
. fix bit shift typo of FIMC register definition
- two cleanups
. remove unnecessary error messages
. remove exynos_drm_rotator.h file
[1] https://patchwork.kernel.org/patch/
10170205/
* tag 'exynos-drm-fixes-for-v4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm: exynos: Use proper macro definition for HDMI_I2S_PIN_SEL_1
drm/exynos: remove exynos_drm_rotator.h
drm/exynos: g2d: Delete an error message for a failed memory allocation in two functions
drm/exynos: fix comparison to bitshift when dealing with a mask
drm/exynos: g2d: use monotonic timestamps
Neil Armstrong [Thu, 15 Feb 2018 10:19:36 +0000 (11:19 +0100)]
drm/meson: fix vsync buffer update
The plane buffer address/stride/height was incorrectly updated in the
plane_atomic_update operation instead of the vsync irq.
This patch delays this operation in the vsync irq along with the
other plane delayed setup.
This issue was masked using legacy framebuffer and X11 modesetting, but
is clearly visible using gbm rendering when buffer is submitted late after
vblank, like using software decoding and OpenGL rendering in Kodi.
With this patch, tearing and other artifacts disappears completely.
Cc: Michal Lazo <michal.lazo@gmail.com>
Fixes:
bbbe775ec5b5 ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1518689976-23292-1-git-send-email-narmstrong@baylibre.com
Chris Wilson [Mon, 19 Feb 2018 11:35:43 +0000 (11:35 +0000)]
drm: Handle unexpected holes in color-eviction
During eviction, the driver may free more than one hole in the drm_mm
due to the side-effects in evicting the scanned nodes. However,
drm_mm_scan_color_evict() expects that the scan result is the first
available hole (in the mru freed hole_stack list):
kernel BUG at drivers/gpu/drm/drm_mm.c:844!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in: i915 snd_hda_codec_analog snd_hda_codec_generic coretemp snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core lpc_ich snd_pcm e1000e mei_me prime_numbers mei
CPU: 1 PID: 1490 Comm: gem_userptr_bli Tainted: G U
4.16.0-rc1-g740f57c54ecf-kasan_6+ #1
Hardware name: Dell Inc. OptiPlex 755 /0PU052, BIOS A08 02/19/2008
RIP: 0010:drm_mm_scan_color_evict+0x2b8/0x3d0
RSP: 0018:
ffff880057a573f8 EFLAGS:
00010287
RAX:
ffff8800611f5980 RBX:
ffff880057a575d0 RCX:
dffffc0000000000
RDX:
00000000029d5000 RSI:
1ffff1000af4aec1 RDI:
ffff8800611f5a10
RBP:
ffff88005ab884d0 R08:
ffff880057a57600 R09:
000000000afff000
R10:
1ffff1000b5710b5 R11:
0000000000001000 R12:
1ffff1000af4ae82
R13:
ffff8800611f59b0 R14:
ffff8800611f5980 R15:
ffff880057a57608
FS:
00007f2de0c2e8c0(0000) GS:
ffff88006ac40000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007f2ddde1e000 CR3:
00000000609b2000 CR4:
00000000000006e0
Call Trace:
? drm_mm_scan_remove_block+0x330/0x330
? drm_mm_scan_remove_block+0x151/0x330
i915_gem_evict_something+0x711/0xbd0 [i915]
? igt_evict_contexts+0x50/0x50 [i915]
? nop_clear_range+0x10/0x10 [i915]
? igt_evict_something+0x90/0x90 [i915]
? i915_gem_gtt_reserve+0x1a1/0x320 [i915]
i915_gem_gtt_insert+0x237/0x400 [i915]
__i915_vma_do_pin+0xc25/0x1a20 [i915]
eb_lookup_vmas+0x1c63/0x3790 [i915]
? i915_gem_check_execbuffer+0x250/0x250 [i915]
? trace_hardirqs_on_caller+0x33f/0x590
? _raw_spin_unlock_irqrestore+0x39/0x60
? __pm_runtime_resume+0x7d/0xf0
i915_gem_do_execbuffer+0x86a/0x2ff0 [i915]
? __kmalloc+0x132/0x340
? i915_gem_execbuffer2_ioctl+0x10f/0x760 [i915]
? drm_ioctl_kernel+0x12e/0x1c0
? drm_ioctl+0x662/0x980
? eb_relocate_slow+0xa90/0xa90 [i915]
? i915_gem_execbuffer2_ioctl+0x10f/0x760 [i915]
? __might_fault+0xea/0x1a0
i915_gem_execbuffer2_ioctl+0x3cc/0x760 [i915]
? i915_gem_execbuffer_ioctl+0xba0/0xba0 [i915]
? lock_acquire+0x3c0/0x3c0
? i915_gem_execbuffer_ioctl+0xba0/0xba0 [i915]
drm_ioctl_kernel+0x12e/0x1c0
drm_ioctl+0x662/0x980
? i915_gem_execbuffer_ioctl+0xba0/0xba0 [i915]
? drm_getstats+0x20/0x20
? debug_check_no_obj_freed+0x2a6/0x8c0
do_vfs_ioctl+0x170/0xe70
? ioctl_preallocate+0x170/0x170
? task_work_run+0xbe/0x160
? lock_acquire+0x3c0/0x3c0
? trace_hardirqs_on_caller+0x33f/0x590
? _raw_spin_unlock_irq+0x2f/0x50
SyS_ioctl+0x36/0x70
? do_vfs_ioctl+0xe70/0xe70
do_syscall_64+0x18c/0x5d0
entry_SYSCALL_64_after_hwframe+0x26/0x9b
RIP: 0033:0x7f2ddf13b587
RSP: 002b:
00007fff15c4f9d8 EFLAGS:
00000246 ORIG_RAX:
0000000000000010
RAX:
ffffffffffffffda RBX:
0000000000000003 RCX:
00007f2ddf13b587
RDX:
00007fff15c4fa20 RSI:
0000000040406469 RDI:
0000000000000003
RBP:
00007fff15c4fa20 R08:
0000000000000000 R09:
00007f2ddf3fe120
R10:
0000000000000073 R11:
0000000000000246 R12:
0000000040406469
R13:
0000000000000003 R14:
00007fff15c4fa20 R15:
00000000000000c7
Code: 00 00 00 4a c7 44 22 08 00 00 00 00 42 c7 44 22 10 00 00 00 00 48 81 c4 b8 00 00 00 5b 5d 41 5c 41 5d 41 5e 41 5f c3 0f 0b 0f 0b <0f> 0b 31 c0 eb c0 4c 89 ef e8 9a 09 41 ff e9 1e fe ff ff 4c 89
RIP: drm_mm_scan_color_evict+0x2b8/0x3d0 RSP:
ffff880057a573f8
We can trivially relax this assumption by searching the hole_stack for
the scan result and warn instead if the driver called us without any
result.
Fixes:
3fa489dabea9 ("drm: Apply tight eviction scanning to color_adjust")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.11+
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180219113543.8010-1-chris@chris-wilson.co.uk
Sylwester Nawrocki [Wed, 14 Feb 2018 17:23:56 +0000 (18:23 +0100)]
drm: exynos: Use proper macro definition for HDMI_I2S_PIN_SEL_1
Bit field [2:0] of HDMI_I2S_PIN_SEL_1 corresponds to SDATA_0,
not SDATA_2. This patch removes redefinition of HDMI_I2S_SEL_DATA2
constant and adds missing HDMI_I2S_SEL_DATA0.
The value of bit field selecting SDATA_1 (pin_sel_3) is also changed,
so it is 3 as suggested in the Exynos TRMs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Corentin Labbe [Thu, 15 Feb 2018 08:23:15 +0000 (08:23 +0000)]
drm/exynos: remove exynos_drm_rotator.h
Since its inclusion in 2012 via commit
bea8a429d91a ("drm/exynos: add rotator ipp driver")
this header is not used by any source files and is empty.
Lets just remove it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Markus Elfring [Thu, 8 Feb 2018 17:42:51 +0000 (18:42 +0100)]
drm/exynos: g2d: Delete an error message for a failed memory allocation in two functions
Omit an extra message for a memory allocation failure in these functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Wolfram Sang [Mon, 5 Feb 2018 20:09:59 +0000 (21:09 +0100)]
drm/exynos: fix comparison to bitshift when dealing with a mask
Due to a typo, the mask was destroyed by a comparison instead of a bit
shift.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Arnd Bergmann [Wed, 17 Jan 2018 17:01:21 +0000 (18:01 +0100)]
drm/exynos: g2d: use monotonic timestamps
The exynos DRM driver uses real-time 'struct timeval' values
for exporting its timestamps to user space. This has multiple
problems:
1. signed seconds overflow in y2038
2. the 'struct timeval' definition is deprecated in the kernel
3. time may jump or go backwards after a 'settimeofday()' syscall
4. other DRM timestamps are in CLOCK_MONOTONIC domain, so they
can't be compared
5. exporting microseconds requires a division by 1000, which may
be slow on some architectures.
The code existed in two places before, but the IPP portion was
removed in
8ded59413ccc ("drm/exynos: ipp: Remove Exynos DRM
IPP subsystem"), so we no longer need to worry about it.
Ideally timestamps should just use 64-bit nanoseconds instead, but
of course we can't change that now. Instead, this tries to address
the first four points above by using monotonic 'timespec' values.
According to Tobias Jakobi, user space doesn't care about the
timestamp at the moment, so we can change the format. Even if
there is something looking at them, it will work just fine with
monotonic times as long as the application only looks at the
relative values between two events.
Link: https://patchwork.kernel.org/patch/10038593/
Cc: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Kai-Heng Feng [Sun, 18 Feb 2018 08:53:59 +0000 (16:53 +0800)]
drm/edid: Add 6 bpc quirk for CPT panel in Asus UX303LA
Similar to commit
e10aec652f31 ("drm/edid: Add 6 bpc quirk for display
AEO model 0."), the EDID reports "DFP 1.x compliant TMDS" but it support
6bpc instead of 8 bpc.
Hence, use 6 bpc quirk for this panel.
Fixes:
196f954e2509 ("drm/i915/dp: Revert "drm/i915/dp: fall back to 18 bpp when sink capability is unknown"")
BugLink: https://bugs.launchpad.net/bugs/1749420
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180218085359.7817-1-kai.heng.feng@canonical.com
Linus Torvalds [Mon, 19 Feb 2018 01:29:42 +0000 (17:29 -0800)]
Linux 4.16-rc2
Linus Torvalds [Sun, 18 Feb 2018 20:56:41 +0000 (12:56 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 Kconfig fixes from Thomas Gleixner:
"Three patchlets to correct HIGHMEM64G and CMPXCHG64 dependencies in
Kconfig when CPU selections are explicitely set to M586 or M686"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/Kconfig: Explicitly enumerate i686-class CPUs in Kconfig
x86/Kconfig: Exclude i586-class CPUs lacking PAE support from the HIGHMEM64G Kconfig group
x86/Kconfig: Add missing i586-class CPUs to the X86_CMPXCHG64 Kconfig group
Linus Torvalds [Sun, 18 Feb 2018 20:38:40 +0000 (12:38 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf updates from Thomas Gleixner:
"Perf tool updates and kprobe fixes:
- perf_mmap overwrite mode fixes/overhaul, prep work to get 'perf
top' using it, making it bearable to use it in large core count
systems such as Knights Landing/Mill Intel systems (Kan Liang)
- s/390 now uses syscall.tbl, just like x86-64 to generate the
syscall table id -> string tables used by 'perf trace' (Hendrik
Brueckner)
- Use strtoull() instead of home grown function (Andy Shevchenko)
- Synchronize kernel ABI headers, v4.16-rc1 (Ingo Molnar)
- Document missing 'perf data --force' option (Sangwon Hong)
- Add perf vendor JSON metrics for ARM Cortex-A53 Processor (William
Cohen)
- Improve error handling and error propagation of ftrace based
kprobes so failures when installing kprobes are not silently
ignored and create disfunctional tracepoints"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
kprobes: Propagate error from disarm_kprobe_ftrace()
kprobes: Propagate error from arm_kprobe_ftrace()
Revert "tools include s390: Grab a copy of arch/s390/include/uapi/asm/unistd.h"
perf s390: Rework system call table creation by using syscall.tbl
perf s390: Grab a copy of arch/s390/kernel/syscall/syscall.tbl
tools/headers: Synchronize kernel ABI headers, v4.16-rc1
perf test: Fix test trace+probe_libc_inet_pton.sh for s390x
perf data: Document missing --force option
perf tools: Substitute yet another strtoull()
perf top: Check the latency of perf_top__mmap_read()
perf top: Switch default mode to overwrite mode
perf top: Remove lost events checking
perf hists browser: Add parameter to disable lost event warning
perf top: Add overwrite fall back
perf evsel: Expose the perf_missing_features struct
perf top: Check per-event overwrite term
perf mmap: Discard legacy interface for mmap read
perf test: Update mmap read functions for backward-ring-buffer test
perf mmap: Introduce perf_mmap__read_event()
perf mmap: Introduce perf_mmap__read_done()
...
Linus Torvalds [Sun, 18 Feb 2018 20:22:04 +0000 (12:22 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"A small set of updates mostly for irq chip drivers:
- MIPS GIC fix for spurious, masked interrupts
- fix for a subtle IPI bug in GICv3
- do not probe GICv3 ITSs that are marked as disabled
- multi-MSI support for GICv2m
- various small cleanups"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqdomain: Re-use DEFINE_SHOW_ATTRIBUTE() macro
irqchip/bcm: Remove hashed address printing
irqchip/gic-v2m: Add PCI Multi-MSI support
irqchip/gic-v3: Ignore disabled ITS nodes
irqchip/gic-v3: Use wmb() instead of smb_wmb() in gic_raise_softirq()
irqchip/gic-v3: Change pr_debug message to pr_devel
irqchip/mips-gic: Avoid spuriously handling masked interrupts
Linus Torvalds [Sun, 18 Feb 2018 19:54:22 +0000 (11:54 -0800)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull core fix from Thomas Gleixner:
"A small fix which adds the missing for_each_cpu_wrap() stub for the UP
case to avoid build failures"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpumask: Make for_each_cpu_wrap() available on UP as well
Linus Torvalds [Sat, 17 Feb 2018 18:20:47 +0000 (10:20 -0800)]
Merge tag 'for-linus-
20180217' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request from Keith, with fixes all over the map for nvme.
From various folks.
- Classic polling fix, that avoids a latency issue where we still end
up waiting for an interrupt in some cases. From Nitesh Shetty.
- Comment typo fix from Minwoo Im.
* tag 'for-linus-
20180217' of git://git.kernel.dk/linux-block:
block: fix a typo in comment of BLK_MQ_POLL_STATS_BKTS
nvme-rdma: fix sysfs invoked reset_ctrl error flow
nvmet: Change return code of discard command if not supported
nvme-pci: Fix timeouts in connecting state
nvme-pci: Remap CMB SQ entries on every controller reset
nvme: fix the deadlock in nvme_update_formats
blk: optimization for classic polling
nvme: Don't use a stack buffer for keep-alive command
nvme_fc: cleanup io completion
nvme_fc: correct abort race condition on resets
nvme: Fix discard buffer overrun
nvme: delete NVME_CTRL_LIVE --> NVME_CTRL_CONNECTING transition
nvme-rdma: use NVME_CTRL_CONNECTING state to mark init process
nvme: rename NVME_CTRL_RECONNECTING state to NVME_CTRL_CONNECTING
Linus Torvalds [Sat, 17 Feb 2018 18:08:28 +0000 (10:08 -0800)]
Merge tag 'mmc-v4.16-rc1' of git://git./linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- meson-gx: Revert to earlier tuning process
- bcm2835: Don't overwrite max frequency unconditionally
* tag 'mmc-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: bcm2835: Don't overwrite max frequency unconditionally
Revert "mmc: meson-gx: include tx phase in the tuning process"
Linus Torvalds [Sat, 17 Feb 2018 18:06:13 +0000 (10:06 -0800)]
Merge tag 'mtd/fixes-for-4.16-rc2' of git://git.infradead.org/linux-mtd
Pull mtd fixes from Boris Brezillon:
- add missing dependency to NAND_MARVELL Kconfig entry
- use the appropriate OOB layout in the VF610 driver
* tag 'mtd/fixes-for-4.16-rc2' of git://git.infradead.org/linux-mtd:
mtd: nand: MTD_NAND_MARVELL should depend on HAS_DMA
mtd: nand: vf610: set correct ooblayout
Linus Torvalds [Sat, 17 Feb 2018 17:48:26 +0000 (09:48 -0800)]
Merge tag 'powerpc-4.16-3' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"The main attraction is a fix for a bug in the new drmem code, which
was causing an oops on boot on some versions of Qemu.
There's also a fix for XIVE (Power9 interrupt controller) on KVM, as
well as a few other minor fixes.
Thanks to: Corentin Labbe, Cyril Bur, Cédric Le Goater, Daniel Black,
Nathan Fontenot, Nicholas Piggin"
* tag 'powerpc-4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Check for zero filled ibm,dynamic-memory property
powerpc/pseries: Add empty update_numa_cpu_lookup_table() for NUMA=n
powerpc/powernv: IMC fix out of bounds memory access at shutdown
powerpc/xive: Use hw CPU ids when configuring the CPU queues
powerpc: Expose TSCR via sysfs only on powernv
Linus Torvalds [Sat, 17 Feb 2018 17:46:18 +0000 (09:46 -0800)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"The bulk of this is the pte accessors annotation to READ/WRITE_ONCE
(we tried to avoid pushing this during the merge window to avoid
conflicts)
- Updated the page table accessors to use READ/WRITE_ONCE and prevent
compiler transformation that could lead to an apparent loss of
coherency
- Enabled branch predictor hardening for the Falkor CPU
- Fix interaction between kpti enabling and KASan causing the
recursive page table walking to take a significant time
- Fix some sparse warnings"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: cputype: Silence Sparse warnings
arm64: mm: Use READ_ONCE/WRITE_ONCE when accessing page tables
arm64: proc: Set PTE_NG for table entries to avoid traversing them twice
arm64: Add missing Falkor part number for branch predictor hardening
Linus Torvalds [Sat, 17 Feb 2018 17:16:09 +0000 (09:16 -0800)]
Merge tag 'for-linus-4.16a-rc2-tag' of git://git./linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- fixes for the Xen pvcalls frontend driver
- fix for booting Xen pv domains
- fix for the xenbus driver user interface
* tag 'for-linus-4.16a-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
pvcalls-front: wait for other operations to return when release passive sockets
pvcalls-front: introduce a per sock_mapping refcount
x86/xen: Calculate __max_logical_packages on PV domains
xenbus: track caller request id
Stefano Stabellini [Wed, 14 Feb 2018 18:28:24 +0000 (10:28 -0800)]
pvcalls-front: wait for other operations to return when release passive sockets
Passive sockets can have ongoing operations on them, specifically, we
have two wait_event_interruptable calls in pvcalls_front_accept.
Add two wake_up calls in pvcalls_front_release, then wait for the
potential waiters to return and release the sock_mapping refcount.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Stefano Stabellini [Wed, 14 Feb 2018 18:28:23 +0000 (10:28 -0800)]
pvcalls-front: introduce a per sock_mapping refcount
Introduce a per sock_mapping refcount, in addition to the existing
global refcount. Thanks to the sock_mapping refcount, we can safely wait
for it to be 1 in pvcalls_front_release before freeing an active socket,
instead of waiting for the global refcount to be 1.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Prarit Bhargava [Wed, 7 Feb 2018 23:49:23 +0000 (18:49 -0500)]
x86/xen: Calculate __max_logical_packages on PV domains
The kernel panics on PV domains because native_smp_cpus_done() is
only called for HVM domains.
Calculate __max_logical_packages for PV domains.
Fixes:
b4c0a7326f5d ("x86/smpboot: Fix __max_logical_packages estimate")
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Tested-and-reported-by: Simon Gaiser <simon@invisiblethingslab.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: xen-devel@lists.xenproject.org
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Joao Martins [Fri, 2 Feb 2018 17:42:33 +0000 (17:42 +0000)]
xenbus: track caller request id
Commit
fd8aa9095a95 ("xen: optimize xenbus driver for multiple concurrent
xenstore accesses") optimized xenbus concurrent accesses but in doing so
broke UABI of /dev/xen/xenbus. Through /dev/xen/xenbus applications are in
charge of xenbus message exchange with the correct header and body. Now,
after the mentioned commit the replies received by application will no
longer have the header req_id echoed back as it was on request (see
specification below for reference), because that particular field is being
overwritten by kernel.
struct xsd_sockmsg
{
uint32_t type; /* XS_??? */
uint32_t req_id;/* Request identifier, echoed in daemon's response. */
uint32_t tx_id; /* Transaction id (0 if not related to a transaction). */
uint32_t len; /* Length of data following this. */
/* Generally followed by nul-terminated string(s). */
};
Before there was only one request at a time so req_id could simply be
forwarded back and forth. To allow simultaneous requests we need a
different req_id for each message thus kernel keeps a monotonic increasing
counter for this field and is written on every request irrespective of
userspace value.
Forwarding again the req_id on userspace requests is not a solution because
we would open the possibility of userspace-generated req_id colliding with
kernel ones. So this patch instead takes another route which is to
artificially keep user req_id while keeping the xenbus logic as is. We do
that by saving the original req_id before xs_send(), use the private kernel
counter as req_id and then once reply comes and was validated, we restore
back the original req_id.
Cc: <stable@vger.kernel.org> # 4.11
Fixes:
fd8aa9095a ("xen: optimize xenbus driver for multiple concurrent xenstore accesses")
Reported-by: Bhavesh Davda <bhavesh.davda@oracle.com>
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Robin Murphy [Fri, 16 Feb 2018 17:04:23 +0000 (17:04 +0000)]
arm64: cputype: Silence Sparse warnings
Sparse makes a fair bit of noise about our MPIDR mask being implicitly
long - let's explicitly describe it as such rather than just relying on
the value forcing automatic promotion.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Lukas Wunner [Sun, 11 Feb 2018 09:38:28 +0000 (10:38 +0100)]
drm/amdgpu: Fix deadlock on runtime suspend
amdgpu's ->runtime_suspend hook calls drm_kms_helper_poll_disable(),
which waits for the output poll worker to finish if it's running.
The output poll worker meanwhile calls pm_runtime_get_sync() in
amdgpu's ->detect hooks, which waits for the ongoing suspend to finish,
causing a deadlock.
Fix by not acquiring a runtime PM ref if the ->detect hooks are called
in the output poll worker's context. This is safe because the poll
worker is only enabled while runtime active and we know that
->runtime_suspend waits for it to finish.
Fixes:
d38ceaf99ed0 ("drm/amdgpu: add core driver (v4)")
Cc: stable@vger.kernel.org # v4.2+: 27d4ee03078a: workqueue: Allow retrieval of current task's work struct
Cc: stable@vger.kernel.org # v4.2+: 25c058ccaf2e: drm: Allow determining if current task is output poll worker
Cc: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Mike Lothian <mike@fireburn.co.uk>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/4c9bf72aacae1eef062bd134cd112e0770a7f121.1518338789.git.lukas@wunner.de
Lukas Wunner [Sun, 11 Feb 2018 09:38:28 +0000 (10:38 +0100)]
drm/radeon: Fix deadlock on runtime suspend
radeon's ->runtime_suspend hook calls drm_kms_helper_poll_disable(),
which waits for the output poll worker to finish if it's running.
The output poll worker meanwhile calls pm_runtime_get_sync() in
radeon's ->detect hooks, which waits for the ongoing suspend to finish,
causing a deadlock.
Fix by not acquiring a runtime PM ref if the ->detect hooks are called
in the output poll worker's context. This is safe because the poll
worker is only enabled while runtime active and we know that
->runtime_suspend waits for it to finish.
Stack trace for posterity:
INFO: task kworker/0:3:31847 blocked for more than 120 seconds
Workqueue: events output_poll_execute [drm_kms_helper]
Call Trace:
schedule+0x3c/0x90
rpm_resume+0x1e2/0x690
__pm_runtime_resume+0x3f/0x60
radeon_lvds_detect+0x39/0xf0 [radeon]
output_poll_execute+0xda/0x1e0 [drm_kms_helper]
process_one_work+0x14b/0x440
worker_thread+0x48/0x4a0
INFO: task kworker/2:0:10493 blocked for more than 120 seconds.
Workqueue: pm pm_runtime_work
Call Trace:
schedule+0x3c/0x90
schedule_timeout+0x1b3/0x240
wait_for_common+0xc2/0x180
wait_for_completion+0x1d/0x20
flush_work+0xfc/0x1a0
__cancel_work_timer+0xa5/0x1d0
cancel_delayed_work_sync+0x13/0x20
drm_kms_helper_poll_disable+0x1f/0x30 [drm_kms_helper]
radeon_pmops_runtime_suspend+0x3d/0xa0 [radeon]
pci_pm_runtime_suspend+0x61/0x1a0
vga_switcheroo_runtime_suspend+0x21/0x70
__rpm_callback+0x32/0x70
rpm_callback+0x24/0x80
rpm_suspend+0x12b/0x640
pm_runtime_work+0x6f/0xb0
process_one_work+0x14b/0x440
worker_thread+0x48/0x4a0
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94147
Fixes:
10ebc0bc0934 ("drm/radeon: add runtime PM support (v2)")
Cc: stable@vger.kernel.org # v3.13+: 27d4ee03078a: workqueue: Allow retrieval of current task's work struct
Cc: stable@vger.kernel.org # v3.13+: 25c058ccaf2e: drm: Allow determining if current task is output poll worker
Cc: Ismo Toijala <ismo.toijala@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/64ea02c44f91dda19bc563902b97bbc699040392.1518338789.git.lukas@wunner.de
Lukas Wunner [Sun, 11 Feb 2018 09:38:28 +0000 (10:38 +0100)]
drm/nouveau: Fix deadlock on runtime suspend
nouveau's ->runtime_suspend hook calls drm_kms_helper_poll_disable(),
which waits for the output poll worker to finish if it's running.
The output poll worker meanwhile calls pm_runtime_get_sync() in
nouveau_connector_detect() which waits for the ongoing suspend to finish,
causing a deadlock.
Fix by not acquiring a runtime PM ref if nouveau_connector_detect() is
called in the output poll worker's context. This is safe because
the poll worker is only enabled while runtime active and we know that
->runtime_suspend waits for it to finish.
Other contexts calling nouveau_connector_detect() do require a runtime
PM ref, these comprise:
status_store() drm sysfs interface
->fill_modes drm callback
drm_fb_helper_probe_connector_modes()
drm_mode_getconnector()
nouveau_connector_hotplug()
nouveau_display_hpd_work()
nv17_tv_set_property()
Stack trace for posterity:
INFO: task kworker/0:1:58 blocked for more than 120 seconds.
Workqueue: events output_poll_execute [drm_kms_helper]
Call Trace:
schedule+0x28/0x80
rpm_resume+0x107/0x6e0
__pm_runtime_resume+0x47/0x70
nouveau_connector_detect+0x7e/0x4a0 [nouveau]
nouveau_connector_detect_lvds+0x132/0x180 [nouveau]
drm_helper_probe_detect_ctx+0x85/0xd0 [drm_kms_helper]
output_poll_execute+0x11e/0x1c0 [drm_kms_helper]
process_one_work+0x184/0x380
worker_thread+0x2e/0x390
INFO: task kworker/0:2:252 blocked for more than 120 seconds.
Workqueue: pm pm_runtime_work
Call Trace:
schedule+0x28/0x80
schedule_timeout+0x1e3/0x370
wait_for_completion+0x123/0x190
flush_work+0x142/0x1c0
nouveau_pmops_runtime_suspend+0x7e/0xd0 [nouveau]
pci_pm_runtime_suspend+0x5c/0x180
vga_switcheroo_runtime_suspend+0x1e/0xa0
__rpm_callback+0xc1/0x200
rpm_callback+0x1f/0x70
rpm_suspend+0x13c/0x640
pm_runtime_work+0x6e/0x90
process_one_work+0x184/0x380
worker_thread+0x2e/0x390
Bugzilla: https://bugs.archlinux.org/task/53497
Bugzilla: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=870523
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70388#c33
Fixes:
5addcf0a5f0f ("nouveau: add runtime PM support (v0.9)")
Cc: stable@vger.kernel.org # v3.12+: 27d4ee03078a: workqueue: Allow retrieval of current task's work struct
Cc: stable@vger.kernel.org # v3.12+: 25c058ccaf2e: drm: Allow determining if current task is output poll worker
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/b7d2cbb609a80f59ccabfdf479b9d5907c603ea1.1518338789.git.lukas@wunner.de
Lukas Wunner [Wed, 14 Feb 2018 05:41:25 +0000 (06:41 +0100)]
drm: Allow determining if current task is output poll worker
Introduce a helper to determine if the current task is an output poll
worker.
This allows us to fix a long-standing deadlock in several DRM drivers
wherein the ->runtime_suspend callback waits for the output poll worker
to finish and the worker in turn calls a ->detect callback which waits
for runtime suspend to finish. The ->detect callback is invoked from
multiple call sites and waiting for runtime suspend to finish is the
correct thing to do except if it's executing in the context of the
worker.
v2: Expand kerneldoc to specifically mention deadlock between
output poll worker and autosuspend worker as use case. (Lyude)
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/3549ce32e7f1467102e70d3e9cbf70c46bfe108e.1518593424.git.lukas@wunner.de
Lukas Wunner [Sun, 11 Feb 2018 09:38:28 +0000 (10:38 +0100)]
workqueue: Allow retrieval of current task's work struct
Introduce a helper to retrieve the current task's work struct if it is
a workqueue worker.
This allows us to fix a long-standing deadlock in several DRM drivers
wherein the ->runtime_suspend callback waits for a specific worker to
finish and that worker in turn calls a function which waits for runtime
suspend to finish. That function is invoked from multiple call sites
and waiting for runtime suspend to finish is the correct thing to do
except if it's executing in the context of the worker.
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/2d8f603074131eb87e588d2b803a71765bd3a2fd.1518338788.git.lukas@wunner.de
Linus Torvalds [Fri, 16 Feb 2018 20:22:33 +0000 (12:22 -0800)]
Merge tag 'dma-mapping-4.16-2' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"A few dma-mapping fixes for the fallout from the changes in rc1"
* tag 'dma-mapping-4.16-2' of git://git.infradead.org/users/hch/dma-mapping:
powerpc/macio: set a proper dma_coherent_mask
dma-mapping: fix a comment typo
dma-direct: comment the dma_direct_free calling convention
dma-direct: mark as is_phys
ia64: fix build failure with CONFIG_SWIOTLB
Will Deacon [Thu, 15 Feb 2018 11:14:56 +0000 (11:14 +0000)]
arm64: mm: Use READ_ONCE/WRITE_ONCE when accessing page tables
In many cases, page tables can be accessed concurrently by either another
CPU (due to things like fast gup) or by the hardware page table walker
itself, which may set access/dirty bits. In such cases, it is important
to use READ_ONCE/WRITE_ONCE when accessing page table entries so that
entries cannot be torn, merged or subject to apparent loss of coherence
due to compiler transformations.
Whilst there are some scenarios where this cannot happen (e.g. pinned
kernel mappings for the linear region), the overhead of using READ_ONCE
/WRITE_ONCE everywhere is minimal and makes the code an awful lot easier
to reason about. This patch consistently uses these macros in the arch
code, as well as explicitly namespacing pointers to page table entries
from the entries themselves by using adopting a 'p' suffix for the former
(as is sometimes used elsewhere in the kernel source).
Tested-by: Yury Norov <ynorov@caviumnetworks.com>
Tested-by: Richard Ruigrok <rruigrok@codeaurora.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Arnd Bergmann [Fri, 16 Feb 2018 15:25:53 +0000 (16:25 +0100)]
mm: hide a #warning for COMPILE_TEST
We get a warning about some slow configurations in randconfig kernels:
mm/memory.c:83:2: error: #warning Unfortunate NUMA and NUMA Balancing config, growing page-frame for last_cpupid. [-Werror=cpp]
The warning is reasonable by itself, but gets in the way of randconfig
build testing, so I'm hiding it whenever CONFIG_COMPILE_TEST is set.
The warning was added in 2013 in commit
75980e97dacc ("mm: fold
page->_last_nid into page->flags where possible").
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 16 Feb 2018 17:31:37 +0000 (09:31 -0800)]
Merge tag 'mips_fixes_4.16_2' of git://git./linux/kernel/git/jhogan/mips
Pull MIPS fixes from James Hogan:
"A few fixes for outstanding MIPS issues:
- an __init section mismatch warning when brcmstb_pm is enabled
- a regression handling multiple mem=X@Y arguments (4.11)
- a USB Kconfig select warning, and related sparc cleanup (4.16)"
* tag 'mips_fixes_4.16_2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
sparc,leon: Select USB_UHCI_BIG_ENDIAN_{MMIO,DESC}
usb: Move USB_UHCI_BIG_ENDIAN_* out of USB_SUPPORT
MIPS: Fix incorrect mem=X@Y handling
MIPS: BMIPS: Fix section mismatch warning
Linus Torvalds [Fri, 16 Feb 2018 17:26:18 +0000 (09:26 -0800)]
Merge tag 'for-4.16-rc1-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"We have a few assorted fixes, some of them show up during fstests so I
gave them more testing"
* tag 'for-4.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: Fix use-after-free when cleaning up fs_devs with a single stale device
Btrfs: fix null pointer dereference when replacing missing device
btrfs: remove spurious WARN_ON(ref->count < 0) in find_parent_nodes
btrfs: Ignore errors from btrfs_qgroup_trace_extent_post
Btrfs: fix unexpected -EEXIST when creating new inode
Btrfs: fix use-after-free on root->orphan_block_rsv
Btrfs: fix btrfs_evict_inode to handle abnormal inodes correctly
Btrfs: fix extent state leak from tree log
Btrfs: fix crash due to not cleaning up tree log block's dirty bits
Btrfs: fix deadlock in run_delalloc_nocow
Linus Torvalds [Fri, 16 Feb 2018 17:23:36 +0000 (09:23 -0800)]
Merge tag 'for-4.16/dm-chained-bios-fix' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix for DM core to properly propagate errors (avoids overriding
non-zero error with 0). This is particularly important given DM core's
increased use of chained bios"
* tag 'for-4.16/dm-chained-bios-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: correctly handle chained bios in dec_pending()
Linus Torvalds [Fri, 16 Feb 2018 17:20:00 +0000 (09:20 -0800)]
Merge tag 'platform-drivers-x86-v4.16-4' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Andy Shevchenko:
- regression fix in keyboard support for Dell laptops
- prevent out-of-boundary write in WMI bus driver
- increase timeout to read functional key status on Lenovo laptops
* tag 'platform-drivers-x86-v4.16-4' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: dell-laptop: Removed duplicates in DMI whitelist
platform/x86: dell-laptop: fix kbd_get_state's request value
platform/x86: ideapad-laptop: Increase timeout to wait for EC answer
platform/x86: wmi: fix off-by-one write in wmi_dev_probe()
Linus Torvalds [Fri, 16 Feb 2018 17:11:30 +0000 (09:11 -0800)]
Merge tag 'sound-4.16-rc2' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of usual suspects:
- a handful USB-audio and HD-audio device-specific quirks
- some trivial fixes for the new AC97 bus stuff
- another race fix in ALSA sequencer core"
* tag 'sound-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: PCI quirk for Fujitsu U7x7
ALSA: seq: Fix racy pool initializations
ALSA: usb: add more device quirks for USB DSD devices
ALSA: usb-audio: Fix UAC2 get_ctl request with a RANGE attribute
ALSA: ac97: Fix copy and paste typo in documentation
ALSA: usb-audio: add implicit fb quirk for Behringer UFX1204
ALSA: ac97: kconfig: Remove select of undefined symbol AC97
ALSA: hda/realtek - Enable Thinkpad Dock device for ALC298 platform
ALSA: hda/realtek - Add headset mode support for Dell laptop
ALSA: hda - Fix headset mic detection problem for two Dell machines
Linus Torvalds [Fri, 16 Feb 2018 17:08:59 +0000 (09:08 -0800)]
Merge tag 'drm-fixes-for-v4.16-rc2' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"One nouveau regression fix, one AMD quirk and a full set of i915
fixes.
The i915 fixes are mostly for things caught by their CI system, main
ones being DSI panel fixes and GEM fixes"
* tag 'drm-fixes-for-v4.16-rc2' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: Make clock gate support conditional
drm/i915: Fix DSI panels with v1 MIPI sequences without a DEASSERT sequence v3
drm/i915: Free memdup-ed DSI VBT data structures on driver_unload
drm/i915: Add intel_bios_cleanup() function
drm/i915/vlv: Add cdclk workaround for DSI
drm/i915/gvt: fix one typo of render_mmio trace
drm/i915/gvt: Support BAR0 8-byte reads/writes
drm/i915/gvt: add 0xe4f0 into gen9 render list
drm/i915/pmu: Fix building without CONFIG_PM
drm/i915/pmu: Fix sleep under atomic in RC6 readout
drm/i915/pmu: Fix PMU enable vs execlists tasklet race
drm/i915: Lock out execlist tasklet while peeking inside for busy-stats
drm/i915/breadcrumbs: Ignore unsubmitted signalers
drm/i915: Don't wake the device up to check if the engine is asleep
drm/i915: Avoid truncation before clamping userspace's priority value
drm/i915/perf: Fix compiler warning for string truncation
drm/i915/perf: Fix compiler warning for string truncation
drm/amdgpu: add new device to use atpx quirk
NeilBrown [Thu, 15 Feb 2018 09:00:15 +0000 (20:00 +1100)]
dm: correctly handle chained bios in dec_pending()
dec_pending() is given an error status (possibly 0) to be recorded
against a bio. It can be called several times on the one 'struct
dm_io', and it is careful to only assign a non-zero error to
io->status. However when it then assigned io->status to bio->bi_status,
it is not careful and could overwrite a genuine error status with 0.
This can happen when chained bios are in use. If a bio is chained
beneath the bio that this dm_io is handling, the child bio might
complete and set bio->bi_status before the dm_io completes.
This has been possible since chained bios were introduced in 3.14, and
has become a lot easier to trigger with commit
18a25da84354 ("dm: ensure
bio submission follows a depth-first tree walk") as that commit caused
dm to start using chained bios itself.
A particular failure mode is that if a bio spans an 'error' target and a
working target, the 'error' fragment will complete instantly and set the
->bi_status, and the other fragment will normally complete a little
later, and will clear ->bi_status.
The fix is simply to only assign io_error to bio->bi_status when
io_error is not zero.
Reported-and-tested-by: Milan Broz <gmazyland@gmail.com>
Cc: stable@vger.kernel.org (v3.14+)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Thomas Gleixner [Fri, 16 Feb 2018 14:47:26 +0000 (15:47 +0100)]
Merge tag 'irqchip-4.16-2' of git://git./linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates for 4.16-rc2 from Marc Zyngier
- A MIPS GIC fix for spurious, masked interrupts
- A fix for a subtle IPI bug in GICv3
- Do not probe GICv3 ITSs that are marked as disabled
- Multi-MSI support for GICv2m
- Various cleanups
Andy Shevchenko [Wed, 14 Feb 2018 15:47:35 +0000 (17:47 +0200)]
irqdomain: Re-use DEFINE_SHOW_ATTRIBUTE() macro
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Jaedon Shin [Mon, 12 Feb 2018 02:18:12 +0000 (11:18 +0900)]
irqchip/bcm: Remove hashed address printing
Since commit
ad67b74d2469 ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful. so delete the prints.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Marc Zyngier [Tue, 6 Feb 2018 18:55:33 +0000 (18:55 +0000)]
irqchip/gic-v2m: Add PCI Multi-MSI support
We'd never implemented Multi-MSI support with GICv2m, because
it is weird and clunky, and you'd think people would rather use
MSI-X.
Turns out there is still plenty of devices out there that rely
on Multi-MSI. Oh well, let's teach that trick to the v2m widget,
it is not a big deal anyway.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Stephen Boyd [Thu, 1 Feb 2018 17:03:29 +0000 (09:03 -0800)]
irqchip/gic-v3: Ignore disabled ITS nodes
On some platforms there's an ITS available but it's not enabled
because reading or writing the registers is denied by the
firmware. In fact, reading or writing them will cause the system
to reset. We could remove the node from DT in such a case, but
it's better to skip nodes that are marked as "disabled" in DT so
that we can describe the hardware that exists and use the status
property to indicate how the firmware has configured things.
Cc: Stuart Yoder <stuyoder@gmail.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Shanker Donthineni [Thu, 1 Feb 2018 00:03:42 +0000 (18:03 -0600)]
irqchip/gic-v3: Use wmb() instead of smb_wmb() in gic_raise_softirq()
A DMB instruction can be used to ensure the relative order of only
memory accesses before and after the barrier. Since writes to system
registers are not memory operations, barrier DMB is not sufficient
for observability of memory accesses that occur before ICC_SGI1R_EL1
writes.
A DSB instruction ensures that no instructions that appear in program
order after the DSB instruction, can execute until the DSB instruction
has completed.
Cc: stable@vger.kernel.org
Acked-by: Will Deacon <will.deacon@arm.com>,
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Mark Salter [Fri, 2 Feb 2018 14:20:29 +0000 (09:20 -0500)]
irqchip/gic-v3: Change pr_debug message to pr_devel
The pr_debug() in gic-v3 gic_send_sgi() can trigger a circular locking
warning:
GICv3: CPU10: ICC_SGI1R_EL1
5000400
======================================================
WARNING: possible circular locking dependency detected
4.15.0+ #1 Tainted: G W
------------------------------------------------------
dynamic_debug01/1873 is trying to acquire lock:
((console_sem).lock){-...}, at: [<
0000000099c891ec>] down_trylock+0x20/0x4c
but task is already holding lock:
(&rq->lock){-.-.}, at: [<
00000000842e1587>] __task_rq_lock+0x54/0xdc
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&rq->lock){-.-.}:
__lock_acquire+0x3b4/0x6e0
lock_acquire+0xf4/0x2a8
_raw_spin_lock+0x4c/0x60
task_fork_fair+0x3c/0x148
sched_fork+0x10c/0x214
copy_process.isra.32.part.33+0x4e8/0x14f0
_do_fork+0xe8/0x78c
kernel_thread+0x48/0x54
rest_init+0x34/0x2a4
start_kernel+0x45c/0x488
-> #1 (&p->pi_lock){-.-.}:
__lock_acquire+0x3b4/0x6e0
lock_acquire+0xf4/0x2a8
_raw_spin_lock_irqsave+0x58/0x70
try_to_wake_up+0x48/0x600
wake_up_process+0x28/0x34
__up.isra.0+0x60/0x6c
up+0x60/0x68
__up_console_sem+0x4c/0x7c
console_unlock+0x328/0x634
vprintk_emit+0x25c/0x390
dev_vprintk_emit+0xc4/0x1fc
dev_printk_emit+0x88/0xa8
__dev_printk+0x58/0x9c
_dev_info+0x84/0xa8
usb_new_device+0x100/0x474
hub_port_connect+0x280/0x92c
hub_event+0x740/0xa84
process_one_work+0x240/0x70c
worker_thread+0x60/0x400
kthread+0x110/0x13c
ret_from_fork+0x10/0x18
-> #0 ((console_sem).lock){-...}:
validate_chain.isra.34+0x6e4/0xa20
__lock_acquire+0x3b4/0x6e0
lock_acquire+0xf4/0x2a8
_raw_spin_lock_irqsave+0x58/0x70
down_trylock+0x20/0x4c
__down_trylock_console_sem+0x3c/0x9c
console_trylock+0x20/0xb0
vprintk_emit+0x254/0x390
vprintk_default+0x58/0x90
vprintk_func+0xbc/0x164
printk+0x80/0xa0
__dynamic_pr_debug+0x84/0xac
gic_raise_softirq+0x184/0x18c
smp_cross_call+0xac/0x218
smp_send_reschedule+0x3c/0x48
resched_curr+0x60/0x9c
check_preempt_curr+0x70/0xdc
wake_up_new_task+0x310/0x470
_do_fork+0x188/0x78c
SyS_clone+0x44/0x50
__sys_trace_return+0x0/0x4
other info that might help us debug this:
Chain exists of:
(console_sem).lock --> &p->pi_lock --> &rq->lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&rq->lock);
lock(&p->pi_lock);
lock(&rq->lock);
lock((console_sem).lock);
*** DEADLOCK ***
2 locks held by dynamic_debug01/1873:
#0: (&p->pi_lock){-.-.}, at: [<
000000001366df53>] wake_up_new_task+0x40/0x470
#1: (&rq->lock){-.-.}, at: [<
00000000842e1587>] __task_rq_lock+0x54/0xdc
stack backtrace:
CPU: 10 PID: 1873 Comm: dynamic_debug01 Tainted: G W 4.15.0+ #1
Hardware name: GIGABYTE R120-T34-00/MT30-GS2-00, BIOS T48 10/02/2017
Call trace:
dump_backtrace+0x0/0x188
show_stack+0x24/0x2c
dump_stack+0xa4/0xe0
print_circular_bug.isra.31+0x29c/0x2b8
check_prev_add.constprop.39+0x6c8/0x6dc
validate_chain.isra.34+0x6e4/0xa20
__lock_acquire+0x3b4/0x6e0
lock_acquire+0xf4/0x2a8
_raw_spin_lock_irqsave+0x58/0x70
down_trylock+0x20/0x4c
__down_trylock_console_sem+0x3c/0x9c
console_trylock+0x20/0xb0
vprintk_emit+0x254/0x390
vprintk_default+0x58/0x90
vprintk_func+0xbc/0x164
printk+0x80/0xa0
__dynamic_pr_debug+0x84/0xac
gic_raise_softirq+0x184/0x18c
smp_cross_call+0xac/0x218
smp_send_reschedule+0x3c/0x48
resched_curr+0x60/0x9c
check_preempt_curr+0x70/0xdc
wake_up_new_task+0x310/0x470
_do_fork+0x188/0x78c
SyS_clone+0x44/0x50
__sys_trace_return+0x0/0x4
GICv3: CPU0: ICC_SGI1R_EL1 12000
This could be fixed with printk_deferred() but that might lessen its
usefulness for debugging. So change it to pr_devel to keep it out of
production kernels. Developers working on gic-v3 can enable it as
needed in their kernels.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Matt Redfearn [Mon, 5 Feb 2018 16:45:36 +0000 (16:45 +0000)]
irqchip/mips-gic: Avoid spuriously handling masked interrupts
Commit
7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading
GIC_SH_MASK*") removed the read of the hardware mask register when
handling shared interrupts, instead using the driver's shadow pcpu_masks
entry as the effective mask. Unfortunately this did not take account of
the write to pcpu_masks during gic_shared_irq_domain_map, which
effectively unmasks the interrupt early. If an interrupt is asserted,
gic_handle_shared_int decodes and processes the interrupt even though it
has not yet been unmasked via gic_unmask_irq, which also sets the
appropriate bit in pcpu_masks.
On the MIPS Boston board, when a console command line of
"console=ttyS0,115200n8r" is passed, the modem status IRQ is enabled in
the UART, which is immediately raised to the GIC. The interrupt has been
mapped, but no handler has yet been registered, nor is it expected to be
unmasked. However, the write to pcpu_masks in gic_shared_irq_domain_map
has effectively unmasked it, resulting in endless reports of:
[ 5.058454] irq 13, desc:
ffffffff80a7ad80, depth: 1, count: 0, unhandled: 0
[ 5.062057] ->handle_irq():
ffffffff801b1838,
[ 5.062175] handle_bad_irq+0x0/0x2c0
Where IRQ 13 is the UART interrupt.
To fix this, just remove the write to pcpu_masks in
gic_shared_irq_domain_map. The existing write in gic_unmask_irq is the
correct place for what is now the effective unmasking.
Cc: stable@vger.kernel.org
Fixes:
7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading GIC_SH_MASK*")
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Nathan Fontenot [Fri, 16 Feb 2018 03:27:41 +0000 (21:27 -0600)]
powerpc/pseries: Check for zero filled ibm,dynamic-memory property
Some versions of QEMU will produce an ibm,dynamic-reconfiguration-memory
node with a ibm,dynamic-memory property that is zero-filled. This
causes the drmem code to oops trying to parse this property.
The fix for this is to validate that the property does contain LMB
entries before trying to parse it and bail if the count is zero.
Oops: Kernel access of bad area, sig: 11 [#1]
DAR:
0000000000000010
NIP read_drconf_v1_cell+0x54/0x9c
LR read_drconf_v1_cell+0x48/0x9c
Call Trace:
__param_initcall_debug+0x0/0x28 (unreliable)
drmem_init+0x144/0x2f8
do_one_initcall+0x64/0x1d0
kernel_init_freeable+0x298/0x38c
kernel_init+0x24/0x160
ret_from_kernel_thread+0x5c/0xb4
The ibm,dynamic-reconfiguration-memory device tree property generated
that causes this:
ibm,dynamic-reconfiguration-memory {
ibm,lmb-size = <0x0 0x10000000>;
ibm,memory-flags-mask = <0xff>;
ibm,dynamic-memory = <0x0 0x0 0x0 0x0 0x0 0x0>;
linux,phandle = <0x7e57eed8>;
ibm,associativity-lookup-arrays = <0x1 0x4 0x0 0x0 0x0 0x0>;
ibm,memory-preservation-time = <0x0>;
};
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Tested-by: Daniel Black <daniel@linux.vnet.ibm.com>
[mpe: Trim oops report]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Kelley [Wed, 14 Feb 2018 02:54:03 +0000 (02:54 +0000)]
cpumask: Make for_each_cpu_wrap() available on UP as well
for_each_cpu_wrap() was originally added in the #else half of a
large "#if NR_CPUS == 1" statement, but was omitted in the #if
half. This patch adds the missing #if half to prevent compile
errors when NR_CPUS is 1.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Michael Kelley <mhkelley@outlook.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kys@microsoft.com
Cc: martin.petersen@oracle.com
Cc: mikelley@microsoft.com
Fixes:
c743f0a5c50f ("sched/fair, cpumask: Export for_each_cpu_wrap()")
Link: http://lkml.kernel.org/r/SN6PR1901MB2045F087F59450507D4FCC17CBF50@SN6PR1901MB2045.namprd19.prod.outlook.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Matthew Whitehead [Thu, 15 Feb 2018 16:54:56 +0000 (11:54 -0500)]
x86/Kconfig: Explicitly enumerate i686-class CPUs in Kconfig
The X86_P6_NOP config class leaves out many i686-class CPUs. Instead,
explicitly enumerate all these CPUs.
Using a configuration with M686 currently sets X86_MINIMUM_CPU_FAMILY=5
instead of the correct value of 6.
Booting on an i586 it will fail to generate the "This kernel
requires an i686 CPU, but only detected an i586 CPU" message and
intentional halt as expected. It will instead just silently hang
when it hits i686-specific instructions.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1518713696-11360-3-git-send-email-tedheadster@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Matthew Whitehead [Thu, 15 Feb 2018 16:54:55 +0000 (11:54 -0500)]
x86/Kconfig: Exclude i586-class CPUs lacking PAE support from the HIGHMEM64G Kconfig group
i586-class machines also lack support for Physical Address Extension (PAE),
so add them to the exclusion list.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1518713696-11360-2-git-send-email-tedheadster@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Matthew Whitehead [Thu, 15 Feb 2018 16:54:54 +0000 (11:54 -0500)]
x86/Kconfig: Add missing i586-class CPUs to the X86_CMPXCHG64 Kconfig group
Several i586-class CPUs supporting this instruction are missing from
the X86_CMPXCHG64 config group.
Using a configuration with either M586TSC or M586MMX currently sets
X86_MINIMUM_CPU_FAMILY=4 instead of the correct value of 5.
Booting on an i486 it will fail to generate the "This kernel
requires an i586 CPU, but only detected an i486 CPU" message and
intentional halt as expected. It will instead just silently hang
when it hits i586-specific instructions.
The M586 CPU is not in this list because at least the Cyrix 5x86
lacks this instruction, and perhaps others.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1518713696-11360-1-git-send-email-tedheadster@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jessica Yu [Tue, 9 Jan 2018 23:51:24 +0000 (00:51 +0100)]
kprobes: Propagate error from disarm_kprobe_ftrace()
Improve error handling when disarming ftrace-based kprobes. Like with
arm_kprobe_ftrace(), propagate any errors from disarm_kprobe_ftrace() so
that we do not disable/unregister kprobes that are still armed. In other
words, unregister_kprobe() and disable_kprobe() should not report success
if the kprobe could not be disarmed.
disarm_all_kprobes() keeps its current behavior and attempts to
disarm all kprobes. It returns the last encountered error and gives a
warning if not all probes could be disarmed.
This patch is based on Petr Mladek's original patchset (patches 2 and 3)
back in 2015, which improved kprobes error handling, found here:
https://lkml.org/lkml/2015/2/26/452
However, further work on this had been paused since then and the patches
were not upstreamed.
Based-on-patches-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S . Miller <davem@davemloft.net>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/20180109235124.30886-3-jeyu@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jessica Yu [Tue, 9 Jan 2018 23:51:23 +0000 (00:51 +0100)]
kprobes: Propagate error from arm_kprobe_ftrace()
Improve error handling when arming ftrace-based kprobes. Specifically, if
we fail to arm a ftrace-based kprobe, register_kprobe()/enable_kprobe()
should report an error instead of success. Previously, this has lead to
confusing situations where register_kprobe() would return 0 indicating
success, but the kprobe would not be functional if ftrace registration
during the kprobe arming process had failed. We should therefore take any
errors returned by ftrace into account and propagate this error so that we
do not register/enable kprobes that cannot be armed. This can happen if,
for example, register_ftrace_function() finds an IPMODIFY conflict (since
kprobe_ftrace_ops has this flag set) and returns an error. Such a conflict
is possible since livepatches also set the IPMODIFY flag for their ftrace_ops.
arm_all_kprobes() keeps its current behavior and attempts to arm all
kprobes. It returns the last encountered error and gives a warning if
not all probes could be armed.
This patch is based on Petr Mladek's original patchset (patches 2 and 3)
back in 2015, which improved kprobes error handling, found here:
https://lkml.org/lkml/2015/2/26/452
However, further work on this had been paused since then and the patches
were not upstreamed.
Based-on-patches-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S . Miller <davem@davemloft.net>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/20180109235124.30886-2-jeyu@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Fri, 16 Feb 2018 08:10:09 +0000 (09:10 +0100)]
Merge tag 'perf-core-for-mingo-4.17-
20180215' of git://git./linux/kernel/git/acme/linux into perf/urgent
Pull perf/core fixes from Arnaldo Carvalho de Melo:
- perf_mmap overwrite mode fixes/overhaul, prep work to get 'perf top'
using it, making it bearable to use it in large core count systems
such as Knights Landing/Mill Intel systems (Kan Liang)
- s/390 now uses syscall.tbl, just like x86-64 to generate the syscall
table id -> string tables used by 'perf trace' (Hendrik Brueckner)
- Use strtoull() instead of home grown function (Andy Shevchenko)
- Synchronize kernel ABI headers, v4.16-rc1 (Ingo Molnar)
- Document missing 'perf data --force' option (Sangwon Hong)
- Add perf vendor JSON metrics for ARM Cortex-A53 Processor (William Cohen)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Airlie [Fri, 16 Feb 2018 04:26:01 +0000 (14:26 +1000)]
Merge branch 'linux-4.16' of git://github.com/skeggsb/linux into drm-fixes
single fix for older gpus.
* 'linux-4.16' of git://github.com/skeggsb/linux:
drm/nouveau: Make clock gate support conditional
Thierry Reding [Wed, 7 Feb 2018 17:40:27 +0000 (18:40 +0100)]
drm/nouveau: Make clock gate support conditional
The recently introduced clock gate support breaks on Tegra chips because
no thermal support is enabled for those devices. Conditionalize the code
on the existence of thermal support to fix this.
Fixes:
b138eca661cc ("drm/nouveau: Add support for basic clockgating on Kepler1")
Cc: Martin Peres <martin.peres@free.fr>
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Dave Airlie [Fri, 16 Feb 2018 02:33:03 +0000 (12:33 +1000)]
Merge tag 'drm-intel-fixes-2018-02-14-1' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
There are important fixes for VLV with MIPI/DSI panels,
2 clean-up patches needed for this MIPI/DSI fix,
and many fixes for GEM including fixes for Perf OA and PMU,
and fixes on scheduler and preemption.
This also includes GVT fixes: "This has one to fix GTT mmio 8b
access from guest and two simple ones for mmio switch and typo fix"
* tag 'drm-intel-fixes-2018-02-14-1' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Fix DSI panels with v1 MIPI sequences without a DEASSERT sequence v3
drm/i915: Free memdup-ed DSI VBT data structures on driver_unload
drm/i915: Add intel_bios_cleanup() function
drm/i915/vlv: Add cdclk workaround for DSI
drm/i915/gvt: fix one typo of render_mmio trace
drm/i915/gvt: Support BAR0 8-byte reads/writes
drm/i915/gvt: add 0xe4f0 into gen9 render list
drm/i915/pmu: Fix building without CONFIG_PM
drm/i915/pmu: Fix sleep under atomic in RC6 readout
drm/i915/pmu: Fix PMU enable vs execlists tasklet race
drm/i915: Lock out execlist tasklet while peeking inside for busy-stats
drm/i915/breadcrumbs: Ignore unsubmitted signalers
drm/i915: Don't wake the device up to check if the engine is asleep
drm/i915: Avoid truncation before clamping userspace's priority value
drm/i915/perf: Fix compiler warning for string truncation
drm/i915/perf: Fix compiler warning for string truncation
Dave Airlie [Fri, 16 Feb 2018 02:30:41 +0000 (12:30 +1000)]
Merge branch 'drm-next-4.16' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
single atpx fix
* 'drm-next-4.16' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: add new device to use atpx quirk
Linus Torvalds [Thu, 15 Feb 2018 22:50:32 +0000 (14:50 -0800)]
Merge tag 'acpi-4.16-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a system resume regression from the 4.13 cycle, clean up
device table handling in the ACPI core, update sysfs ABI documentation
of a couple of drivers and add an expected switch fall-through marker
to the SPCR table parsing code.
Specifics:
- Revert a problematic EC driver change from the 4.13 cycle that
introduced a system resume regression on Thinkpad X240 (Rafael
Wysocki).
- Clean up device tables handling in the ACPI core and the related
part of the device properties framework (Andy Shevchenko).
- Update the sysfs ABI documentatio of the dock and the INT3407
special device drivers (Aishwarya Pant).
- Add an expected switch fall-through marker to the SPCR table
parsing code (Gustavo Silva)"
* tag 'acpi-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: dock: document sysfs interface
ACPI / DPTF: Document dptf_power sysfs atttributes
device property: Constify device_get_match_data()
ACPI / bus: Rename acpi_get_match_data() to acpi_device_get_match_data()
ACPI / bus: Remove checks in acpi_get_match_data()
ACPI / bus: Do not traverse through non-existed device table
ACPI: SPCR: Mark expected switch fall-through in acpi_parse_spcr
ACPI / EC: Restore polling during noirq suspend/resume phases
Linus Torvalds [Thu, 15 Feb 2018 22:40:01 +0000 (14:40 -0800)]
Merge tag 'pm-4.16-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a recently introduced build issue related to cpuidle and two
bugs in the PM core, update cpuidle documentation and clean up memory
allocations in the operating performance points (OPP) framework.
Specifics:
- Fix a recently introduced build issue related to cpuidle by
covering all of the relevant combinations of Kconfig options
in its header (Rafael Wysocki).
- Add missing invocation of pm_runtime_drop_link() to the
!CONFIG_SRCU variant of __device_link_del() (Lukas Wunner).
- Fix unbalanced IRQ enable in the wakeup interrupts framework
(Tony Lindgren).
- Update cpuidle sysfs ABI documentation (Aishwarya Pant).
- Use GFP_KERNEL instead of GFP_ATOMIC for allocating memory
in dev_pm_opp_init_cpufreq_table() (Jia-Ju Bai)"
* tag 'pm-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: cpuidle: Fix cpuidle_poll_state_init() prototype
PM / runtime: Update links_count also if !CONFIG_SRCU
PM / wakeirq: Fix unbalanced IRQ enable for wakeirq
Documentation/ABI: update cpuidle sysfs documentation
opp: cpu: Replace GFP_ATOMIC with GFP_KERNEL in dev_pm_opp_init_cpufreq_table
Linus Torvalds [Thu, 15 Feb 2018 22:31:28 +0000 (14:31 -0800)]
Merge tag 'hwmon-for-linus-v4.16-rc2' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix bad temperature display on Ryzen/Threadripper"
* tag 'hwmon-for-linus-v4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (k10temp) Only apply temperature offset if result is positive
Linus Torvalds [Thu, 15 Feb 2018 22:29:27 +0000 (14:29 -0800)]
Merge tag 'for_linus' of git://git./linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"This includes a bugfix for virtio 9p fs. It also fixes hybernation for
s390 guests with virtio devices"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio/s390: implement PM operations for virtio_ccw
9p/trans_virtio: discard zero-length reply
James Hogan [Wed, 31 Jan 2018 22:24:46 +0000 (22:24 +0000)]
sparc,leon: Select USB_UHCI_BIG_ENDIAN_{MMIO,DESC}
Now that USB_UHCI_BIG_ENDIAN_MMIO and USB_UHCI_BIG_ENDIAN_DESC are moved
outside of the USB_SUPPORT conditional, simply select them from
SPARC_LEON rather than by the symbol's defaults in drivers/usb/Kconfig,
similar to how it is done for USB_EHCI_BIG_ENDIAN_MMIO and
USB_EHCI_BIG_ENDIAN_DESC.
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: sparclinux@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: https://patchwork.linux-mips.org/patch/18560/
James Hogan [Wed, 31 Jan 2018 22:24:45 +0000 (22:24 +0000)]
usb: Move USB_UHCI_BIG_ENDIAN_* out of USB_SUPPORT
Move the Kconfig symbols USB_UHCI_BIG_ENDIAN_MMIO and
USB_UHCI_BIG_ENDIAN_DESC out of drivers/usb/host/Kconfig, which is
conditional upon USB && USB_SUPPORT, so that it can be freely selected
by platform Kconfig symbols in architecture code.
For example once the MIPS_GENERIC platform selects are fixed in commit
2e6522c56552 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN"), the MIPS
32r6_defconfig warns like so:
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB)
Fixes:
2e6522c56552 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patchwork: https://patchwork.linux-mips.org/patch/18559/
Linus Torvalds [Thu, 15 Feb 2018 17:28:47 +0000 (09:28 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes:
- fix rq->lock lockdep annotation bug
- fix/improve update_curr_rt() and update_curr_dl() accounting
- update documentation
- remove unused macro"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/cpufreq: Remove unused SUGOV_KTHREAD_PRIORITY macro
sched/core: Fix DEBUG_SPINLOCK annotation for rq->lock
sched/rt: Make update_curr_rt() more accurate
sched/deadline: Make update_curr_dl() more accurate
membarrier-sync-core: Document architecture support
Linus Torvalds [Thu, 15 Feb 2018 17:05:26 +0000 (09:05 -0800)]
Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"This contains two qspinlock fixes and three documentation and comment
fixes"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/semaphore: Update the file path in documentation
locking/atomic/bitops: Document and clarify ordering semantics for failed test_and_{}_bit()
locking/qspinlock: Ensure node->count is updated before initialising node
locking/qspinlock: Ensure node is initialised before updating prev->next
Documentation/locking/mutex-design: Update to reflect latest changes
Minwoo Im [Thu, 15 Feb 2018 14:53:17 +0000 (23:53 +0900)]
block: fix a typo in comment of BLK_MQ_POLL_STATS_BKTS
Update comment typo _consisitent_ to _consistent_ from following commit.
commit
0206319fdfee ("blk-mq: Fix poll_stat for new size-based bucketing.")
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Hendrik Brueckner [Thu, 8 Feb 2018 11:47:48 +0000 (12:47 +0100)]
Revert "tools include s390: Grab a copy of arch/s390/include/uapi/asm/unistd.h"
This reverts commit
f120c7b187e6c418238710b48723ce141f467543 which is no
longer required with the introduction of a syscall.tbl on s390.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Thomas Richter <tmricht@linux.vnet.ibm.com>
Cc: linux-s390@vger.kernel.org
LPU-Reference:
1518090470-2899-2-git-send-email-brueckner@linux.vnet.ibm.com
Link: https://lkml.kernel.org/n/tip-q1lg0nvhha1tk39ri9aqalcb@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Hendrik Brueckner [Thu, 8 Feb 2018 11:47:50 +0000 (12:47 +0100)]
perf s390: Rework system call table creation by using syscall.tbl
Recently, s390 uses a syscall.tbl input file to generate its system call
table and unistd uapi header files. Hence, update mksyscalltbl to use
it as input to create the system table for perf.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Thomas Richter <tmricht@linux.vnet.ibm.com>
Cc: linux-s390@vger.kernel.org
LPU-Reference:
1518090470-2899-4-git-send-email-brueckner@linux.vnet.ibm.com
Link: https://lkml.kernel.org/n/tip-bdyhllhsq1zgxv2qx4m377y6@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Hendrik Brueckner [Thu, 8 Feb 2018 11:47:49 +0000 (12:47 +0100)]
perf s390: Grab a copy of arch/s390/kernel/syscall/syscall.tbl
Grab a copy of the s390 system call table file introduced with commit
857f46bfb07f53dc112d69bdfb137cc5ec3da7c5 "s390/syscalls: add system call
table".
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Thomas Richter <tmricht@linux.vnet.ibm.com>
Cc: linux-s390@vger.kernel.org
LPU-Reference:
1518090470-2899-3-git-send-email-brueckner@linux.vnet.ibm.com
Link: https://lkml.kernel.org/n/tip-hpw7vdjp7g92ivgpddrp5ydq@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Ingo Molnar [Tue, 13 Feb 2018 11:54:58 +0000 (12:54 +0100)]
tools/headers: Synchronize kernel ABI headers, v4.16-rc1
Sync the following tooling headers with the latest kernel version:
tools/arch/powerpc/include/uapi/asm/kvm.h
tools/arch/x86/include/asm/cpufeatures.h
tools/include/uapi/drm/i915_drm.h
tools/include/uapi/linux/if_link.h
tools/include/uapi/linux/kvm.h
All the changes are new ABI additions which don't impact their use
in existing tooling.
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Thomas Richter [Wed, 17 Jan 2018 08:38:31 +0000 (09:38 +0100)]
perf test: Fix test trace+probe_libc_inet_pton.sh for s390x
On Intel test case trace+probe_libc_inet_pton.sh succeeds and the
output is:
[root@f27 perf]# ./perf trace --no-syscalls
-e probe_libc:inet_pton/max-stack=3/ ping -6 -c 1 ::1
PING ::1(::1) 56 data bytes
64 bytes from ::1: icmp_seq=1 ttl=64 time=0.037 ms
--- ::1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.037/0.037/0.037/0.000 ms
0.000 probe_libc:inet_pton:(
7fa40ac618a0))
__GI___inet_pton (/usr/lib64/libc-2.26.so)
getaddrinfo (/usr/lib64/libc-2.26.so)
main (/usr/bin/ping)
The kernel stack unwinder is used, it is specified implicitly
as call-graph=fp (frame pointer).
On s390x only dwarf is available for stack unwinding. It is also
done in user space. This requires different parameter setup
and result checking for s390x and Intel.
This patch adds separate perf trace setup and result checking
for Intel and s390x. On s390x specify this command line to
get a call-graph and handle the different call graph result
checking:
[root@s35lp76 perf]# ./perf trace --no-syscalls
-e probe_libc:inet_pton/call-graph=dwarf/ ping -6 -c 1 ::1
PING ::1(::1) 56 data bytes
64 bytes from ::1: icmp_seq=1 ttl=64 time=0.041 ms
--- ::1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.041/0.041/0.041/0.000 ms
0.000 probe_libc:inet_pton:(
3ffb9942060))
__GI___inet_pton (/usr/lib64/libc-2.26.so)
gaih_inet (inlined)
__GI_getaddrinfo (inlined)
main (/usr/bin/ping)
__libc_start_main (/usr/lib64/libc-2.26.so)
_start (/usr/bin/ping)
[root@s35lp76 perf]#
Before:
[root@s8360047 perf]# ./perf test -vv 58
58: probe libc's inet_pton & backtrace it with ping :
--- start ---
test child forked, pid 26349
PING ::1(::1) 56 data bytes
64 bytes from ::1: icmp_seq=1 ttl=64 time=0.079 ms
--- ::1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.079/0.079/0.079/0.000 ms
0.000 probe_libc:inet_pton:(
3ff925c2060))
test child finished with -1
---- end ----
probe libc's inet_pton & backtrace it with ping: FAILED!
[root@s8360047 perf]#
After:
[root@s35lp76 perf]# ./perf test -vv 57
57: probe libc's inet_pton & backtrace it with ping :
--- start ---
test child forked, pid 38708
PING ::1(::1) 56 data bytes
64 bytes from ::1: icmp_seq=1 ttl=64 time=0.038 ms
--- ::1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.038/0.038/0.038/0.000 ms
0.000 probe_libc:inet_pton:(
3ff87342060))
__GI___inet_pton (/usr/lib64/libc-2.26.so)
gaih_inet (inlined)
__GI_getaddrinfo (inlined)
main (/usr/bin/ping)
__libc_start_main (/usr/lib64/libc-2.26.so)
_start (/usr/bin/ping)
test child finished with 0
---- end ----
probe libc's inet_pton & backtrace it with ping: Ok
[root@s35lp76 perf]#
On Intel the test case runs unchanged and succeeds.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20180117083831.101001-1-tmricht@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Sangwon Hong [Mon, 5 Feb 2018 11:48:35 +0000 (20:48 +0900)]
perf data: Document missing --force option
Add the --force option to the man page.
Signed-off-by: Sangwon Hong <qpakzk@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Taeung Song <treeze.taeung@gmail.com>
Link: http://lkml.kernel.org/r/1517831315-31490-1-git-send-email-qpakzk@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Andy Shevchenko [Mon, 29 Jan 2018 13:03:59 +0000 (15:03 +0200)]
perf tools: Substitute yet another strtoull()
Instead of home grown function let's use what library provides us.
Signed-off-by: Andriy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/20180129130359.1490-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:32 +0000 (13:26 -0800)]
perf top: Check the latency of perf_top__mmap_read()
The latency of perf_top__mmap_read() should be lower than refresh time.
If not, give some hints to reduce the latency.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-18-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:31 +0000 (13:26 -0800)]
perf top: Switch default mode to overwrite mode
perf_top__mmap_read() has a severe performance issue in the Knights
Landing/Mill platform, when monitoring heavy load systems. It costs
several minutes to finish, which is unacceptable.
Currently, 'perf top' uses the non overwrite mode. For non overwrite
mode, it tries to read everything in the ringbuffer and doesn't pause
it. Once there are lots of samples delivered persistently, the
processing time could be very long. Also, the latest samples could be
lost when the ringbuffer is full.
For overwrite mode, it takes a snapshot for the system by pausing the
ringbuffer, which could significantly reduce the processing time. Also,
the overwrite mode always keep the latest samples. Considering the real
time requirement for 'perf top', the overwrite mode is more suitable for
it.
Actually, 'perf top' was overwrite mode. It is changed to non overwrite
mode since commit
93fc64f14472 ("perf top: Switch to non overwrite
mode"). It's better to change it back to overwrite mode by default.
For the kernel which doesn't support overwrite mode, it will fall back
to non overwrite mode.
There would be some records lost in overwrite mode because of pausing
the ringbuffer. It has little impact for the accuracy of the snapshot
and can be tolerated.
For overwrite mode, unconditionally wait 100 ms before each snapshot. It
also reduces the overhead caused by pausing ringbuffer, especially on
light load system.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-17-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:30 +0000 (13:26 -0800)]
perf top: Remove lost events checking
There would be some records lost in overwrite mode because of pausing
the ringbuffer. It has little impact for the accuracy of the snapshot
and could be tolerated by 'perf top'.
Remove the lost events checking.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-16-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:29 +0000 (13:26 -0800)]
perf hists browser: Add parameter to disable lost event warning
For overwrite mode, the ringbuffer will be paused. The event lost is
expected. It needs a way to notify the browser not print the warning.
It will be used later for perf top to disable lost event warning in
overwrite mode. There is no behavior change for now.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-15-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:28 +0000 (13:26 -0800)]
perf top: Add overwrite fall back
Switch to non-overwrite mode if kernel doesnot support overwrite
ringbuffer.
It's only effect when overwrite mode is supported. No change to current
behavior.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-14-git-send-email-kan.liang@intel.com
[ Use perf_missing_features.write_backward instead of the non merged is_write_backward_fail() ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Fri, 2 Feb 2018 14:27:25 +0000 (11:27 -0300)]
perf evsel: Expose the perf_missing_features struct
As tools may need to adjust to missing features, as 'perf top' will, in
the next csets, to cope with a missing 'write_backward' feature.
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-jelngl9q1ooaizvkcput9tic@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:26 +0000 (13:26 -0800)]
perf top: Check per-event overwrite term
Per-event overwrite term is not forbidden in 'perf top', which can bring
problems. Because 'perf top' only support non-overwrite mode now.
Add new rules and check regarding to overwrite term for 'perf top'.
- All events either have same per-event term or don't have per-event
mode setting. Otherwise, it will error out.
- Per-event overwrite term should be consistent as opts->overwrite.
If not, updating the opts->overwrite according to per-event term.
Make it possible to support either non-overwrite or overwrite mode.
The overwrite mode is forbidden now, which will be removed when the
overwrite mode is supported later.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-12-git-send-email-kan.liang@intel.com
[ Renamed perf_top_overwrite_check to perf_top__overwrite_check, to follow existing convention ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:25 +0000 (13:26 -0800)]
perf mmap: Discard legacy interface for mmap read
Discards perf_mmap__read_backward() and perf_mmap__read_catchup(). No
tools use them.
There are tools still use perf_mmap__read_forward(). Keep it, but add
comments to point to the new interface for future use.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-11-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:24 +0000 (13:26 -0800)]
perf test: Update mmap read functions for backward-ring-buffer test
Use the new perf_mmap__read_* interfaces for overwrite ringbuffer test.
Commiter notes:
Testing:
[root@seventh ~]# perf test -v backward
48: Read backward ring buffer :
--- start ---
test child forked, pid 8309
Using CPUID GenuineIntel-6-9E
mmap size
1052672B
mmap size 8192B
Finished reading overwrite ring buffer: rewind
test child finished with 0
---- end ----
Read backward ring buffer: Ok
[root@seventh ~]#
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-10-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:23 +0000 (13:26 -0800)]
perf mmap: Introduce perf_mmap__read_event()
Except for 'perf record', the other perf tools read events one by one
from the ring buffer using perf_mmap__read_forward(). But it only
supports non-overwrite mode.
Introduce perf_mmap__read_event() to support both non-overwrite and
overwrite mode.
Usage:
perf_mmap__read_init()
while(event = perf_mmap__read_event()) {
//process the event
perf_mmap__consume()
}
perf_mmap__read_done()
It cannot use perf_mmap__read_backward(). Because it always reads the
stale buffer which is already processed. Furthermore, the forward and
backward concepts have been removed. The perf_mmap__read_backward() will
be replaced and discarded later.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-9-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>