OSDN Git Service
David S. Miller [Fri, 20 Mar 2020 04:14:46 +0000 (21:14 -0700)]
Merge branch 'mscc-RGMII'
Antoine Tenart says:
====================
net: phy: mscc: add support for RGMII MAC mode
This series adds support for the RGMII MAC mode for the VSC8584 PHY
family and for RGMII_ID modes (Tx and/or Rx).
I decided to drop the custom delay for now. I made some tests and it
seemed to be working quite well. If we find out we really need to lower
the delay, which I doubt, I'll send support for it.
Since v2:
- Dropped support for custom dt bindings.
- Add the 2ns delay based on the interface mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Thu, 19 Mar 2020 14:19:58 +0000 (15:19 +0100)]
net: phy: mscc: RGMII skew delay configuration
This patch adds support for configuring the RGMII skew delays in Rx and
Tx. The Rx and Tx skews are set based on the interface mode. By default
their configuration is set to the default value in hardware (0.2ns);
this means the driver do not rely anymore on the bootloader
configuration.
Then based on the interface mode being used, a 2ns delay is added:
- RGMII_ID adds it for both Rx and Tx.
- RGMII_RXID adds it for Rx.
- RGMII_TXID adds it for Tx.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Thu, 19 Mar 2020 14:19:57 +0000 (15:19 +0100)]
net: phy: mscc: add support for RGMII MAC mode
This patch adds support for connecting VSC8584 PHYs to the MAC using
RGMII.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 20 Mar 2020 04:09:20 +0000 (21:09 -0700)]
Merge branch 'mlxsw-Offload-TC-action-skbedit-priority'
Ido Schimmel says:
====================
mlxsw: Offload TC action skbedit priority
Petr says:
The TC action "skbedit priority P" has the effect of assigning skbprio of P
to SKBs that it's applied on. In HW datapath of a switch, the corresponding
action is assignment of internal switch priority. Spectrum switches allow
setting of packet priority based on an ACL action, which is good match for
the skbedit priority gadget. This patchset therefore implements offloading
of this action to the Spectrum ACL engine.
After a bit of refactoring in patch #1, patch #2 extends the skbedit action
to support offloading of "priority" subcommand.
On mlxsw side, in patch #3, the QOS_ACTION flexible action is added, with
fields necessary for priority adjustment. In patch #4, "skbedit priority"
is connected to that action.
Patch #5 implements a new forwarding selftest, suitable for both SW- and
HW-datapath testing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 19 Mar 2020 13:47:24 +0000 (15:47 +0200)]
selftests: forwarding: Add an skbedit priority selftest
Add a test that runs traffic through a port such that skbedit priority
action acts on it during forwarding. Test that at egress, it is classified
correctly according to the new priority at a PRIO qdisc.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 19 Mar 2020 13:47:23 +0000 (15:47 +0200)]
mlxsw: spectrum_flower: Offload FLOW_ACTION_PRIORITY
Offload action skbedit priority when keyed to a flower classifier. The
skb->priority field in Linux is very generic, so only allow setting the
bottom 8 priorities and bounce anything else.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 19 Mar 2020 13:47:22 +0000 (15:47 +0200)]
mlxsw: core: Add QOS_ACTION
The QOS_ACTION is used for manipulating the QoS attributes of a packet.
Add the corresponding defines and helpers, in particular for the
switch_priority override.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 19 Mar 2020 13:47:21 +0000 (15:47 +0200)]
net: tc_skbedit: Make the skbedit priority offloadable
The skbedit action "priority" is used for adjusting SKB priority. Allow
drivers to offload the action by introducing two new skbedit getters and a
new flow action, and initializing appropriately in tc_setup_flow_action().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 19 Mar 2020 13:47:20 +0000 (15:47 +0200)]
net: tc_skbedit: Factor a helper out of is_tcf_skbedit_{mark, ptype}()
The two functions is_tcf_skbedit_mark() and is_tcf_skbedit_ptype() have a
very similar structure. A follow-up patch will add one more such function.
Instead of more cut'n'pasting, extract a helper function that checks
whether a TC action is an skbedit with the required flag. Convert the two
existing functions into thin wrappers around the helper.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dejin Zheng [Thu, 19 Mar 2020 13:16:38 +0000 (21:16 +0800)]
net: stmmac: dwmac_lib: remove unnecessary checks in dwmac_dma_reset()
it will check the return value of dwmac_dma_reset() in the
stmmac_init_dma_engine() function and report an error if the
return value is not zero. so don't need check here.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Thu, 19 Mar 2020 12:48:19 +0000 (13:48 +0100)]
net: phy: mscc: add missing check on a phy_write return value
Commit
a5afc1678044 ("net: phy: mscc: add support for VSC8584 PHY")
introduced a call to 'phy_write' storing its return value to a variable
called 'ret'. But 'ret' never was checked for a possible error being
returned, and hence was not used at all. Fix this by checking the return
value and exiting the function if an error was returned.
As this does not fix a known bug, this commit is mostly cosmetic and not
sent as a fix.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Thu, 19 Mar 2020 12:12:00 +0000 (12:12 +0000)]
net: ipa: Remove unused including <linux/version.h>
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Thu, 19 Mar 2020 12:11:27 +0000 (12:11 +0000)]
net: ipa: fix platform_no_drv_owner.cocci warnings
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Thu, 19 Mar 2020 12:07:43 +0000 (12:07 +0000)]
liquidio: remove set but not used variable 's'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'octeon_chip_specific_setup':
drivers/net/ethernet/cavium/liquidio/lio_main.c:1378:8: warning:
variable 's' set but not used [-Wunused-but-set-variable]
It's not used since commit
b6334be64d6f ("net/liquidio: Delete driver version assignment")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 19 Mar 2020 11:33:10 +0000 (13:33 +0200)]
net: sched: Do not assume RTNL is held in tunnel key action helpers
The cited commit removed RTNL from tc_setup_flow_action(), but the
function calls two tunnel key action helpers that use rtnl_dereference()
to fetch the action's parameters. This leads to "suspicious RCU usage"
warnings [1][2].
Change the helpers to use rcu_dereference_protected() while requiring
the action's lock to be held. This is safe because the two helpers are
only called from tc_setup_flow_action() which acquires the lock.
[1]
[ 156.950855] =============================
[ 156.955463] WARNING: suspicious RCU usage
[ 156.960085]
5.6.0-rc5-custom-47426-gdfe43878d573 #2409 Not tainted
[ 156.967116] -----------------------------
[ 156.971728] include/net/tc_act/tc_tunnel_key.h:31 suspicious rcu_dereference_protected() usage!
[ 156.981583]
[ 156.981583] other info that might help us debug this:
[ 156.981583]
[ 156.990675]
[ 156.990675] rcu_scheduler_active = 2, debug_locks = 1
[ 156.998205] 1 lock held by tc/877:
[ 157.002187] #0:
ffff8881cbf7bea0 (&(&p->tcfa_lock)->rlock){+...}, at: tc_setup_flow_action+0xbe/0x4f78
[ 157.012866]
[ 157.012866] stack backtrace:
[ 157.017886] CPU: 2 PID: 877 Comm: tc Not tainted
5.6.0-rc5-custom-47426-gdfe43878d573 #2409
[ 157.027253] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016
[ 157.037389] Call Trace:
[ 157.040170] dump_stack+0xfd/0x178
[ 157.044034] lockdep_rcu_suspicious+0x14a/0x153
[ 157.049157] tc_setup_flow_action+0x89f/0x4f78
[ 157.054227] fl_hw_replace_filter+0x375/0x640
[ 157.064348] fl_change+0x28ec/0x4f6b
[ 157.088843] tc_new_tfilter+0x15e2/0x2260
[ 157.176801] rtnetlink_rcv_msg+0x8d6/0xb60
[ 157.190915] netlink_rcv_skb+0x177/0x460
[ 157.208884] rtnetlink_rcv+0x21/0x30
[ 157.212925] netlink_unicast+0x5d0/0x7f0
[ 157.227728] netlink_sendmsg+0x981/0xe90
[ 157.245416] ____sys_sendmsg+0x76d/0x8f0
[ 157.255348] ___sys_sendmsg+0x10f/0x190
[ 157.320308] __sys_sendmsg+0x115/0x1f0
[ 157.342553] __x64_sys_sendmsg+0x7d/0xc0
[ 157.346987] do_syscall_64+0xc1/0x600
[ 157.351142] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[2]
[ 157.432346] =============================
[ 157.436937] WARNING: suspicious RCU usage
[ 157.441537]
5.6.0-rc5-custom-47426-gdfe43878d573 #2409 Not tainted
[ 157.448559] -----------------------------
[ 157.453204] include/net/tc_act/tc_tunnel_key.h:43 suspicious rcu_dereference_protected() usage!
[ 157.463042]
[ 157.463042] other info that might help us debug this:
[ 157.463042]
[ 157.472112]
[ 157.472112] rcu_scheduler_active = 2, debug_locks = 1
[ 157.479529] 1 lock held by tc/877:
[ 157.483442] #0:
ffff8881cbf7bea0 (&(&p->tcfa_lock)->rlock){+...}, at: tc_setup_flow_action+0xbe/0x4f78
[ 157.494119]
[ 157.494119] stack backtrace:
[ 157.499114] CPU: 2 PID: 877 Comm: tc Not tainted
5.6.0-rc5-custom-47426-gdfe43878d573 #2409
[ 157.508485] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016
[ 157.518628] Call Trace:
[ 157.521416] dump_stack+0xfd/0x178
[ 157.525293] lockdep_rcu_suspicious+0x14a/0x153
[ 157.530425] tc_setup_flow_action+0x993/0x4f78
[ 157.535505] fl_hw_replace_filter+0x375/0x640
[ 157.545650] fl_change+0x28ec/0x4f6b
[ 157.570204] tc_new_tfilter+0x15e2/0x2260
[ 157.658199] rtnetlink_rcv_msg+0x8d6/0xb60
[ 157.672315] netlink_rcv_skb+0x177/0x460
[ 157.690278] rtnetlink_rcv+0x21/0x30
[ 157.694320] netlink_unicast+0x5d0/0x7f0
[ 157.709129] netlink_sendmsg+0x981/0xe90
[ 157.726813] ____sys_sendmsg+0x76d/0x8f0
[ 157.736725] ___sys_sendmsg+0x10f/0x190
[ 157.801721] __sys_sendmsg+0x115/0x1f0
[ 157.823967] __x64_sys_sendmsg+0x7d/0xc0
[ 157.828403] do_syscall_64+0xc1/0x600
[ 157.832558] entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes:
b15e7a6e8d31 ("net: sched: don't take rtnl lock during flow_action setup")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Thu, 19 Mar 2020 10:14:14 +0000 (12:14 +0200)]
net: bridge: vlan: include stats in dumps if requested
This patch adds support for vlan stats to be included when dumping vlan
information. We have to dump them only when explicitly requested (thus the
flag below) because that disables the vlan range compression and will make
the dump significantly larger. In order to request the stats to be
included we add a new dump attribute called BRIDGE_VLANDB_DUMP_FLAGS which
can affect dumps with the following first flag:
- BRIDGE_VLANDB_DUMPF_STATS
The stats are intentionally nested and put into separate attributes to make
it easier for extending later since we plan to add per-vlan mcast stats,
drop stats and possibly STP stats. This is the last missing piece from the
new vlan API which makes the dumped vlan information complete.
A dump request which should include stats looks like:
[BRIDGE_VLANDB_DUMP_FLAGS] |= BRIDGE_VLANDB_DUMPF_STATS
A vlandb entry attribute with stats looks like:
[BRIDGE_VLANDB_ENTRY] = {
[BRIDGE_VLANDB_ENTRY_STATS] = {
[BRIDGE_VLANDB_STATS_RX_BYTES]
[BRIDGE_VLANDB_STATS_RX_PACKETS]
...
}
}
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 19 Mar 2020 10:06:30 +0000 (11:06 +0100)]
mptcp: rename fourth ack field
The name is misleading, it actually tracks the 'fully established'
status.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 19 Mar 2020 02:13:37 +0000 (19:13 -0700)]
Merge tag 'mlx5-updates-2020-03-17' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-03-17
1) Compiler warnings and cleanup for the connection tracking series
2) Bug fixes for the connection tracking series
3) Fix devlink port register sequence
4) Last five patches in the series, By Eli cohen
Add the support for forwarding traffic between two eswitch uplink
representors (Hairpin for eswitch), using mlx5 termination tables
to change the direction of a packet in hw from RX to TX pipeline.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 18 Mar 2020 22:07:24 +0000 (23:07 +0100)]
net: phy: realtek: read actual speed to detect downshift
At least some integrated PHY's in RTL8168/RTL8125 chip versions support
downshift, and the actual link speed can be read from a vendor-specific
register. Info about this register was provided by Realtek.
More details about downshift configuration (e.g. number of attempts)
aren't available, therefore the downshift tunable is not implemented.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Wed, 18 Mar 2020 17:42:29 +0000 (19:42 +0200)]
net: sched: Fix hw_stats_type setting in pedit loop
In the commit referenced below, hw_stats_type of an entry is set for every
entry that corresponds to a pedit action. However, the assignment is only
done after the entry pointer is bumped, and therefore could overwrite
memory outside of the entries array.
The reason for this positioning may have been that the current entry's
hw_stats_type is already set above, before the action-type dispatch.
However, if there are no more actions, the assignment is wrong. And if
there are, the next round of the for_each_action loop will make the
assignment before the action-type dispatch anyway.
Therefore fix this issue by simply reordering the two lines.
Fixes:
74522e7baae2 ("net: sched: set the hw_stats_type in pedit loop")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Mar 2020 23:46:20 +0000 (16:46 -0700)]
Merge branch 'mlxsw-spectrum_cnt-Expose-counter-resources'
Ido Schimmel says:
====================
mlxsw: spectrum_cnt: Expose counter resources
Jiri says:
Capacity and utilization of existing flow and RIF counters are currently
unavailable to be seen by the user. Use the existing devlink resources
API to expose the information:
$ sudo devlink resource show pci/0000:00:10.0 -v
pci/0000:00:10.0:
name kvd resource_path /kvd size 524288 unit entry dpipe_tables none
name span_agents resource_path /span_agents size 8 occ 0 unit entry dpipe_tables none
name counters resource_path /counters size 79872 occ 44 unit entry dpipe_tables none
resources:
name flow resource_path /counters/flow size 61440 occ 4 unit entry dpipe_tables none
name rif resource_path /counters/rif size 18432 occ 40 unit entry dpipe_tables none
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Wed, 18 Mar 2020 13:48:57 +0000 (15:48 +0200)]
selftests: mlxsw: Add tc action hw_stats tests
Add tests for mlxsw hw_stats types.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Wed, 18 Mar 2020 13:48:56 +0000 (15:48 +0200)]
mlxsw: spectrum_cnt: Expose devlink resource occupancy for counters
Implement occupancy counting for counters and expose over devlink
resource API.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Wed, 18 Mar 2020 13:48:55 +0000 (15:48 +0200)]
mlxsw: spectrum_cnt: Consolidate subpools initialization
Put all init operations related to subpools into
mlxsw_sp_counter_sub_pools_init().
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Wed, 18 Mar 2020 13:48:54 +0000 (15:48 +0200)]
mlxsw: spectrum_cnt: Move config validation along with resource register
Move the validation of subpools configuration, to avoid possible over
commitment to resource registration. Add WARN_ON to indicate bug
in the code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Wed, 18 Mar 2020 13:48:53 +0000 (15:48 +0200)]
mlxsw: spectrum_cnt: Expose subpool sizes over devlink resources
Implement devlink resources support for counter pools. Move the subpool
sizes calculations into the new resources register function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Wed, 18 Mar 2020 13:48:52 +0000 (15:48 +0200)]
mlxsw: spectrum_cnt: Add entry_size_res_id for each subpool and use it to query entry size
Add new field to subpool struct that would indicate which
resource id should be used to query the entry size for
the subpool from the device.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Wed, 18 Mar 2020 13:48:51 +0000 (15:48 +0200)]
mlxsw: spectrum_cnt: Move sub_pools under per-instance pool struct
Currently, the global static array of subpools is used. Make it
per-instance as multiple instances of the mlxsw driver can have
different values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Wed, 18 Mar 2020 13:48:50 +0000 (15:48 +0200)]
selftests: spectrum-2: Adjust tc_flower_scale limit according to current counter count
With the change that made the code to query counter bank size from device
instead of using hard-coded value, the number of available counters
changed for Spectrum-2. Adjust the limit in the selftests.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Wed, 18 Mar 2020 13:48:49 +0000 (15:48 +0200)]
mlxsw: spectrum_cnt: Query bank size from FW resources
The bank size is different between Spectrum versions. Also it is
a resource that can be queried. So instead of hard coding the value in
code, query it from the firmware.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy [Wed, 18 Mar 2020 10:54:51 +0000 (16:24 +0530)]
cxgb4: rework TC filter rule insertion across regions
Chelsio NICs have 3 filter regions, in following order of priority:
1. High Priority (HPFILTER) region (Highest Priority).
2. HASH region.
3. Normal FILTER region (Lowest Priority).
Currently, there's a 1-to-1 mapping between the prio value passed
by TC and the filter region index. However, it's possible to have
multiple TC rules with the same prio value. In this case, if a region
is exhausted, no attempt is made to try inserting the rule in the
next available region.
So, rework and remove the 1-to-1 mapping. Instead, dynamically select
the region to insert the filter rule, as long as the new rule's prio
value doesn't conflict with existing rules across all the 3 regions.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 18 Mar 2020 09:33:22 +0000 (10:33 +0100)]
netfilter: revert introduction of egress hook
This reverts the following commits:
8537f78647c0 ("netfilter: Introduce egress hook")
5418d3881e1f ("netfilter: Generalize ingress hook")
b030f194aed2 ("netfilter: Rename ingress hook include file")
>From the discussion in [0], the author's main motivation to add a hook
in fast path is for an out of tree kernel module, which is a red flag
to begin with. Other mentioned potential use cases like NAT{64,46}
is on future extensions w/o concrete code in the tree yet. Revert as
suggested [1] given the weak justification to add more hooks to critical
fast-path.
[0] https://lore.kernel.org/netdev/cover.
1583927267.git.lukas@wunner.de/
[1] https://lore.kernel.org/netdev/
20200318.011152.
72770718915606186.davem@davemloft.net/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Miller <davem@davemloft.net>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Nacked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Mar 2020 23:33:36 +0000 (16:33 -0700)]
Merge branch 's390-qeth-next'
Julian Wiedmann says:
====================
s390/qeth: updates 2020-03-18
please apply the following patch series for qeth to netdev's net-next
tree.
This consists of three parts:
1) support for __GFP_MEMALLOC,
2) several ethtool enhancements (.set_channels, SW Timestamping),
3) the usual cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Mar 2020 12:54:55 +0000 (13:54 +0100)]
s390/qeth: use dev->reg_state
To check whether a netdevice has already been registered, look at
NETREG_REGISTERED to replace some hacks I added a while ago.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Mar 2020 12:54:54 +0000 (13:54 +0100)]
s390/qeth: remove gratuitous NULL checks
qeth_do_ioctl() is only reached through our own net_device_ops, so we
can trust that dev->ml_priv still contains what we put there earlier.
qeth_bridgeport_an_set() is an internal function that doesn't require
such sanity checks.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Mar 2020 12:54:53 +0000 (13:54 +0100)]
s390/qeth: add phys_to_virt() translation for AOB
Data addresses in the AOB are absolute, and need to be translated before
being fed into kmem_cache_free(). Currently this phys_to_virt() is a no-op.
Also see commit
2db01da8d25f ("s390/qdio: fill SBALEs with absolute addresses").
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Mar 2020 12:54:52 +0000 (13:54 +0100)]
s390/qeth: don't report hard-coded driver version
Versions are meaningless for an in-kernel driver.
Instead use the UTS_RELEASE that is set by ethtool_get_drvinfo().
Cc: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Mar 2020 12:54:51 +0000 (13:54 +0100)]
s390/qeth: add SW timestamping support for IQD devices
This adds support for SOF_TIMESTAMPING_TX_SOFTWARE.
No support for non-IQD devices, since they orphan the skb in their xmit
path.
To play nice with TX bulking, set the timestamp when the buffer that
contains the skb(s) is actually flushed out to HW.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Mar 2020 12:54:50 +0000 (13:54 +0100)]
s390/qeth: balance the TX queue selection for IQD devices
For ucast traffic, qeth_iqd_select_queue() falls back to
netdev_pick_tx(). This will potentially use skb_tx_hash() to distribute
the flow over all active TX queues - so txq 0 is a valid selection, and
qeth_iqd_select_queue() needs to check for this and put it on some other
queue. As a result, the distribution for ucast flows is unbalanced and
hits QETH_IQD_MIN_UCAST_TXQ heavier than the other queues.
Open-coding a custom variant of skb_tx_hash() isn't an option, since
netdev_pick_tx() also gives us eg. access to XPS. But we can pull a
little trick: add a single TC class that excludes the mcast txq, and
thus encourage skb_tx_hash() to not pick the mcast txq.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Mar 2020 12:54:49 +0000 (13:54 +0100)]
s390/qeth: allow configuration of TX queues for IQD devices
Similar to the support for z/VM NICs, but we need to take extra care
about the dedicated mcast queue:
1. netdev_pick_tx() is unaware of this limitation and might select the
mcast txq. Catch this.
2. require at least _two_ TX queues - one for ucast, one for mcast.
3. when reducing the number of TX queues, there's a potential race
where netdev_cap_txqueue() over-rules the selected txq index and
falls back to index 0. This would place ucast traffic on the mcast
queue, and result in TX errors.
So for IQD, reject a reduction while the interface is running.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Mar 2020 12:54:48 +0000 (13:54 +0100)]
s390/qeth: allow configuration of TX queues for z/VM NICs
Add support for ETHTOOL_SCHANNELS to change the count of active
TX queues.
Since all TX queue structs are pre-allocated and -registered, we just
need to trivially adjust dev->real_num_tx_queues.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Mar 2020 12:54:47 +0000 (13:54 +0100)]
s390/qeth: remove prio-queueing support for z/VM NICs
z/VM NICs don't offer HW QoS for TX rings. So just use netdev_pick_tx()
to distribute the connections equally over all enabled TX queues.
We start with just 1 enabled TX queue (this matches the typical
configuration without prio-queueing). A follow-on patch will allow users
to enable additional TX queues.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Mar 2020 12:54:46 +0000 (13:54 +0100)]
s390/qeth: use memory reserves in TX slow path
When falling back to an allocation from the HW header cache, check if
the skb is eligible for using memory reserves.
This only makes a difference if the cache is empty and needs to be
refilled.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Mar 2020 12:54:45 +0000 (13:54 +0100)]
s390/qeth: use memory reserves to back RX buffers
Use dev_alloc_page() for backing the RX buffers with pages. This way we
pick up __GFP_MEMALLOC.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Mar 2020 06:51:31 +0000 (23:51 -0700)]
Merge git://git./linux/kernel/git/pablo/nf-next
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Use nf_flow_offload_tuple() to fetch flow stats, from Paul Blakey.
2) Add new xt_IDLETIMER hard mode, from Manoj Basapathi.
Follow up patch to clean up this new mode, from Dan Carpenter.
3) Add support for geneve tunnel options, from Xin Long.
4) Make sets built-in and remove modular infrastructure for sets,
from Florian Westphal.
5) Remove unused TEMPLATE_NULLS_VAL, from Li RongQing.
6) Statify nft_pipapo_get, from Chen Wandun.
7) Use C99 flexible-array member, from Gustavo A. R. Silva.
8) More descriptive variable names for bitwise, from Jeremy Sowden.
9) Four patches to add tunnel device hardware offload to the flowtable
infrastructure, from wenxu.
10) pipapo set supports for 8-bit grouping, from Stefano Brivio.
11) pipapo can switch between nibble and byte grouping, also from
Stefano.
12) Add AVX2 vectorized version of pipapo, from Stefano Brivio.
13) Update pipapo to be use it for single ranges, from Stefano.
14) Add stateful expression support to elements via control plane,
eg. counter per element.
15) Re-visit sysctls in unprivileged namespaces, from Florian Westphal.
15) Add new egress hook, from Lukas Wunner.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 17 Mar 2020 14:53:34 +0000 (15:53 +0100)]
mptcp: move msk state update to subflow_syn_recv_sock()
After commit
58b09919626b ("mptcp: create msk early"), the
msk socket is already available at subflow_syn_recv_sock()
time. Let's move there the state update, to mirror more
closely the first subflow state.
The above will also help multiple subflow supports.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Mar 2020 05:51:16 +0000 (22:51 -0700)]
Merge branch 'net-add-phylink-support-for-PCS'
Russell King says:
====================
net: add phylink support for PCS
This series adds support for IEEE 802.3 register set compliant PCS
for phylink. In order to do this, we:
1. convert BUG_ON() in existing accessors to WARN_ON_ONCE() and return
an error.
2. add accessors for modifying a MDIO device register, and use them in
phylib, rather than duplicating the code from phylib.
3. add support for decoding the advertisement from clause 22 compatible
register sets for clause 37 advertisements and SGMII advertisements.
4. add support for clause 45 register sets for 10GBASE-R PCS.
These have been tested on the LX2160A Clearfog-CX platform.
v2: eliminate use of BUG_ON() in the accessors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 17 Mar 2020 14:52:41 +0000 (14:52 +0000)]
net: phylink: pcs: add 802.3 clause 45 helpers
Implement helpers for PCS accessed via the MII bus using 802.3 clause
45 cycles for 10GBASE-R. Only link up/down is supported, 10G full
duplex is assumed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 17 Mar 2020 14:52:36 +0000 (14:52 +0000)]
net: phylink: pcs: add 802.3 clause 22 helpers
Implement helpers for PCS accessed via the MII bus using 802.3 clause
22 cycles, conforming to 802.3 clause 37 and Cisco SGMII specifications
for the advertisement word.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 17 Mar 2020 14:52:31 +0000 (14:52 +0000)]
net: mdiobus: add APIs for modifying a MDIO device register
Add APIs for modifying a MDIO device register, similar to the existing
phy_modify() group of functions, but at mdiobus level instead. Adapt
__phy_modify_changed() to use the new mdiobus level helper.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 17 Mar 2020 14:52:26 +0000 (14:52 +0000)]
net: mdiobus: avoid BUG_ON() in mdiobus accessors
Avoid using BUG_ON() in the mdiobus accessors, prefering instead to use
WARN_ON_ONCE() and returning an error.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Mar 2020 05:47:13 +0000 (22:47 -0700)]
Merge branch 'net-bridge-vlan-options-add-support-for-tunnel-mapping'
Nikolay Aleksandrov says:
====================
net: bridge: vlan options: add support for tunnel mapping
In order to bring the new vlan API on par with the old one and be able
to completely migrate to the new one we need to support vlan tunnel mapping
and statistics. This patch-set takes care of the former by making it a
vlan option. There are two notable issues to deal with:
- vlan range to tunnel range mapping
* The tunnel ids are globally unique for the vlan code and a vlan can
be mapped to one tunnel, so the old API took care of ranges by
taking the starting tunnel id value and incrementally mapping
vlan id(i) -> tunnel id(i). This set takes the same approach and
uses one new attribute - BRIDGE_VLANDB_ENTRY_TUNNEL_ID. If used
with a vlan range then it's the starting tunnel id to map.
- tunnel mapping removal
* Since there are no reserved/special tunnel ids defined, we can't
encode mapping removal within the new attribute, in order to be
able to remove a mapping we add a vlan flag which makes the new
tunnel option remove the mapping
The rest is pretty straight-forward, in fact we directly re-use the old
code for manipulating tunnels by just mapping the command (set/del). In
order to be able to keep detecting vlan ranges we check that the current
vlan has a tunnel and it's extending the current vlan range end's tunnel
id.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 17 Mar 2020 12:08:36 +0000 (14:08 +0200)]
net: bridge: vlan options: add support for tunnel mapping set/del
This patch adds support for manipulating vlan/tunnel mappings. The
tunnel ids are globally unique and are one per-vlan. There were two
trickier issues - first in order to support vlan ranges we have to
compute the current tunnel id in the following way:
- base tunnel id (attr) + current vlan id - starting vlan id
This is in line how the old API does vlan/tunnel mapping with ranges. We
already have the vlan range present, so it's redundant to add another
attribute for the tunnel range end. It's simply base tunnel id + vlan
range. And second to support removing mappings we need an out-of-band way
to tell the option manipulating function because there are no
special/reserved tunnel id values, so we use a vlan flag to denote the
operation is tunnel mapping removal.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 17 Mar 2020 12:08:35 +0000 (14:08 +0200)]
net: bridge: vlan options: add support for tunnel id dumping
Add a new option - BRIDGE_VLANDB_ENTRY_TUNNEL_ID which is used to dump
the tunnel id mapping. Since they're unique per vlan they can enter a
vlan range if they're consecutive, thus we can calculate the tunnel id
range map simply as: vlan range end id - vlan range start id. The
starting point is the tunnel id in BRIDGE_VLANDB_ENTRY_TUNNEL_ID. This
is similar to how the tunnel entries can be created in a range via the
old API (a vlan range maps to a tunnel range).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 17 Mar 2020 12:08:34 +0000 (14:08 +0200)]
net: bridge: vlan tunnel: constify bridge and port arguments
The vlan tunnel code changes vlan options, it shouldn't touch port or
bridge options so we can constify the port argument. This would later help
us to re-use these functions from the vlan options code.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 17 Mar 2020 12:08:33 +0000 (14:08 +0200)]
net: bridge: vlan options: rename br_vlan_opts_eq to br_vlan_opts_eq_range
It is more appropriate name as it shows the intent of why we need to
check the options' state. It also allows us to give meaning to the two
arguments of the function: the first is the current vlan (v_curr) being
checked if it could enter the range ending in the second one (range_end).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Mar 2020 04:37:25 +0000 (21:37 -0700)]
Merge branch 'stmmac-100GB-Enterprise-MAC-support'
Jose Abreu says:
====================
net: stmmac: 100GB Enterprise MAC support
Adds the support for Enterprise MAC IP version which allows operating
speeds up to 100GB.
Patch 1/4, adds the support in XPCS for XLGMII interface that is used in
this kind of Enterprise MAC IPs.
Patch 2/4, adds the XLGMII interface support in stmmac.
Patch 3/4, adds the HW specific support for Enterprise MAC.
We end in patch 4/4, by updating stmmac documentation to mention the
support for this new IP version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Tue, 17 Mar 2020 09:18:53 +0000 (10:18 +0100)]
Documentation: networking: stmmac: Mention new XLGMAC support
Add the Enterprise MAC support to the list of supported IP versions and
the newly added XLGMII interface support.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Tue, 17 Mar 2020 09:18:52 +0000 (10:18 +0100)]
net: stmmac: Add support for Enterprise MAC version
Adds the support for Enterprise MAC IP version which is very similar to
XGMAC. It's so similar that we just need to check the device id and add
new speeds definitions and some minor callbacks.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Tue, 17 Mar 2020 09:18:51 +0000 (10:18 +0100)]
net: stmmac: Add XLGMII support
Add XLGMII support for stmmac including the list of speeds and defines
for them.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Tue, 17 Mar 2020 09:18:50 +0000 (10:18 +0100)]
net: phy: xpcs: Add XLGMII support
Add XLGMII support for XPCS. This does not include Autoneg feature.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Mar 2020 04:18:25 +0000 (21:18 -0700)]
Merge branch 'ionic-bits-and-bytes'
Shannon Nelson says:
====================
ionic bits and bytes
These are a few little updates to the ionic driver while we are in between
other feature work. While these are mostly Fixes, they are almost all low
priority and needn't be promoted to net. The one higher need is patch 1,
but it is fixing something that hasn't made it out of net-next yet.
v3: allow decode of unknown transciever and use type
codes from sfp.h
v2: add Fixes tags to patches 1-4, and a little
description for patch 5
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Tue, 17 Mar 2020 03:22:10 +0000 (20:22 -0700)]
ionic: add decode for IONIC_RC_ENOSUPP
Add decoding for a new firmware error code.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Tue, 17 Mar 2020 03:22:09 +0000 (20:22 -0700)]
ionic: print data for unknown xcvr type
If we don't recognize the transceiver type, set the xcvr type
and data length such that ethtool can at least print the first
256 bytes and the reader can figure out why the transceiver
is not recognized.
While we're here, we can update the phy_id type values to use
the enum values in sfp.h.
Fixes:
4d03e00a2140 ("ionic: Add initial ethtool support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Tue, 17 Mar 2020 03:22:08 +0000 (20:22 -0700)]
ionic: remove adminq napi instance
Remove the adminq's napi struct when tearing down
the adminq.
Fixes:
1d062b7b6f64 ("ionic: Add basic adminq support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Tue, 17 Mar 2020 03:22:07 +0000 (20:22 -0700)]
ionic: deinit rss only if selected
Don't bother de-initing RSS if it wasn't selected.
Fixes:
aa3198819bea ("ionic: Add RSS support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Tue, 17 Mar 2020 03:22:06 +0000 (20:22 -0700)]
ionic: stop devlink warn on mgmt device
If we don't set a port type, the devlink code will eventually
print a WARN in the kernel log. Because the mgmt device is
not really a useful port, don't register it as a devlink port.
Fixes:
b3f064e9746d ("ionic: add support for device id 0x1004")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Mar 2020 04:16:35 +0000 (21:16 -0700)]
Merge branch 'net_sched-allow-use-of-hrtimer-slack'
Eric Dumazet says:
====================
net_sched: allow use of hrtimer slack
Packet schedulers have used hrtimers with exact expiry times.
Some of them can afford having a slack, in order to reduce
the number of timer interrupts and feed bigger batches
to increase efficiency.
FQ for example does not care if throttled packets are
sent with an additional (small) delay.
Original observation of having maybe too many interrupts
was made by Willem de Bruijn.
v2: added strict netlink checking (Jakub Kicinski)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 17 Mar 2020 02:12:51 +0000 (19:12 -0700)]
net_sched: sch_fq: enable use of hrtimer slack
Add a new attribute to control the fq qdisc hrtimer slack.
Default is set to 10 usec.
When/if packets are throttled, fq set up an hrtimer that can
lead to one interrupt per packet in the throttled queue.
By using a timer slack, we allow better use of timer interrupts,
by giving them a chance to call multiple timer callbacks
at each hardware interrupt.
Also, giving a slack allows FQ to dequeue batches of packets
instead of a single one, thus increasing xmit_more efficiency.
This has no negative effect on the rate a TCP flow can sustain,
since each TCP flow maintains its own precise vtime (tp->tcp_wstamp_ns)
v2: added strict netlink checking (as feedback from Jakub Kicinski)
Tested:
1000 concurrent flows all using paced packets.
1,000,000 packets sent per second.
Before the patch :
$ vmstat 2 10
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
0 0 0
60726784 23628
3485992 0 0 138 1 977 535 0 12 87 0 0
0 0 0
60714700 23628
3485628 0 0 0 0
1568827 26462 0 22 78 0 0
1 0 0
60716012 23628
3485656 0 0 0 0
1570034 26216 0 22 78 0 0
0 0 0
60722420 23628
3485492 0 0 0 0
1567230 26424 0 22 78 0 0
0 0 0
60727484 23628
3485556 0 0 0 0
1568220 26200 0 22 78 0 0
2 0 0
60718900 23628
3485380 0 0 0 40
1564721 26630 0 22 78 0 0
2 0 0
60718096 23628
3485332 0 0 0 0
1562593 26432 0 22 78 0 0
0 0 0
60719608 23628
3485064 0 0 0 0
1563806 26238 0 22 78 0 0
1 0 0
60722876 23628
3485236 0 0 0 130
1565874 26566 0 22 78 0 0
1 0 0
60722752 23628
3484908 0 0 0 0
1567646 26247 0 22 78 0 0
After the patch, slack of 10 usec, we can see a reduction of interrupts
per second, and a small decrease of reported cpu usage.
$ vmstat 2 10
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
1 0 0
60722564 23628
3484728 0 0 133 1 696 545 0 13 87 0 0
1 0 0
60722568 23628
3484824 0 0 0 0 977278 25469 0 20 80 0 0
0 0 0
60716396 23628
3484764 0 0 0 0 979997 25326 0 20 80 0 0
0 0 0
60713844 23628
3484960 0 0 0 0 981394 25249 0 20 80 0 0
2 0 0
60720468 23628
3484916 0 0 0 0 982860 25062 0 20 80 0 0
1 0 0
60721236 23628
3484856 0 0 0 0 982867 25100 0 20 80 0 0
1 0 0
60722400 23628
3484456 0 0 0 8 982698 25303 0 20 80 0 0
0 0 0
60715396 23628
3484428 0 0 0 0 981777 25176 0 20 80 0 0
0 0 0
60716520 23628
3486544 0 0 0 36 978965 27857 0 21 79 0 0
0 0 0
60719592 23628
3486516 0 0 0 22 977318 25106 0 20 80 0 0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 17 Mar 2020 02:12:50 +0000 (19:12 -0700)]
net_sched: do not reprogram a timer about to expire
qdisc_watchdog_schedule_range_ns() can use the newly added slack
and avoid rearming the hrtimer a bit earlier than the current
value. This patch has no effect if delta_ns parameter
is zero.
Note that this means the max slack is potentially doubled.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 17 Mar 2020 02:12:49 +0000 (19:12 -0700)]
net_sched: add qdisc_watchdog_schedule_range_ns()
Some packet schedulers might want to add a slack
when programming hrtimers. This can reduce number
of interrupts and increase batch sizes and thus
give good xmit_more savings.
This commit adds qdisc_watchdog_schedule_range_ns()
helper, with an extra delta_ns parameter.
Legacy qdisc_watchdog_schedule_n() becomes an inline
passing a zero slack.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Mar 2020 04:12:40 +0000 (21:12 -0700)]
Merge branch 'nfp-type'
Jakub Kicinski says:
====================
net: rename flow_action stats and set NFP type
Jiri, I hope this is okay with you, I just dropped the "type" from
the helper and value names, and now things should be able to fit
on a line, within 80 characters.
Second patch makes the NFP able to offload DELAYED stats, which
is the type it supports.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 17 Mar 2020 01:42:12 +0000 (18:42 -0700)]
nfp: allow explicitly selected delayed stats
NFP flower offload uses delayed stats. Kernel recently gained
the ability to specify stats types. Make nfp accept DELAYED
stats, not just the catch all "any".
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 17 Mar 2020 01:42:11 +0000 (18:42 -0700)]
net: rename flow_action_hw_stats_types* -> flow_action_hw_stats*
flow_action_hw_stats_types_check() helper takes one of the
FLOW_ACTION_HW_STATS_*_BIT values as input. If we align
the arguments to the opening bracket of the helper there
is no way to call this helper and stay under 80 characters.
Remove the "types" part from the new flow_action helpers
and enum values.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Mar 2020 03:58:22 +0000 (20:58 -0700)]
Merge branch 'net-phy-improve-phy_driver-callback-handle_interrupt'
Heiner Kallweit says:
====================
net: phy: improve phy_driver callback handle_interrupt
did_interrupt() clears the interrupt, therefore handle_interrupt() can
not check which event triggered the interrupt. To overcome this
constraint and allow more flexibility for customer interrupt handlers,
let's decouple handle_interrupt() from parts of the phylib interrupt
handling. Custom interrupt handlers now have to implement the
did_interrupt() functionality in handle_interrupt() if needed.
Fortunately we have just one custom interrupt handler so far (in the
mscc PHY driver), convert it to the changed API and make use of the
benefits.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 16 Mar 2020 21:33:31 +0000 (22:33 +0100)]
net: phy: mscc: consider interrupt source in interrupt handler
Trigger the respective interrupt handler functionality only if the
related interrupt source bit is set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 16 Mar 2020 21:32:33 +0000 (22:32 +0100)]
net: phy: improve phy_driver callback handle_interrupt
did_interrupt() clears the interrupt, therefore handle_interrupt() can
not check which event triggered the interrupt. To overcome this
constraint and allow more flexibility for customer interrupt handlers,
let's decouple handle_interrupt() from parts of the phylib interrupt
handling. Custom interrupt handlers now have to implement the
did_interrupt() functionality in handle_interrupt() if needed.
Fortunately we have just one custom interrupt handler so far (in the
mscc PHY driver), convert it to the changed API.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Mar 2020 03:56:58 +0000 (20:56 -0700)]
Merge branch 'ethtool-consolidate-irq-coalescing-last-part'
Jakub Kicinski says:
====================
ethtool: consolidate irq coalescing - last part
Convert remaining drivers following the groundwork laid in a recent
patch set [1] and continued in [2], [3], [4], [5]. The aim of
the effort is to consolidate irq coalescing parameter validation
in the core.
This set is the sixth and last installment. It converts the remaining
8 drivers in drivers/net/ethernet. The last patch makes declaring
supported IRQ coalescing parameters a requirement.
[1] https://lore.kernel.org/netdev/
20200305051542.991898-1-kuba@kernel.org/
[2] https://lore.kernel.org/netdev/
20200306010602.
1620354-1-kuba@kernel.org/
[3] https://lore.kernel.org/netdev/
20200310021512.
1861626-1-kuba@kernel.org/
[4] https://lore.kernel.org/netdev/
20200311223302.
2171564-1-kuba@kernel.org/
[5] https://lore.kernel.org/netdev/
20200313040803.
2367590-1-kuba@kernel.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 16 Mar 2020 20:47:12 +0000 (13:47 -0700)]
net: ethtool: require drivers to set supported_coalesce_params
Now that all in-tree drivers have been updated we can
make the supported_coalesce_params mandatory.
To save debugging time in case some driver was missed
(or is out of tree) add a warning when netdev is registered
with set_coalesce but without supported_coalesce_params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 16 Mar 2020 20:47:11 +0000 (13:47 -0700)]
net: axienet: let core reject the unsupported coalescing parameters
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver already correctly rejected all unsupported
parameters. No functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 16 Mar 2020 20:47:10 +0000 (13:47 -0700)]
net: ll_temac: let core reject the unsupported coalescing parameters
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver already correctly rejected all unsupported
parameters. No functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 16 Mar 2020 20:47:09 +0000 (13:47 -0700)]
net: davinci_emac: reject unsupported coalescing params
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 16 Mar 2020 20:47:08 +0000 (13:47 -0700)]
net: cpsw: reject unsupported coalescing params
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 16 Mar 2020 20:47:07 +0000 (13:47 -0700)]
net: tehuti: reject unsupported coalescing params
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 16 Mar 2020 20:47:06 +0000 (13:47 -0700)]
net: dwc-xlgmac: let core reject the unsupported coalescing parameters
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver already correctly rejected all unsupported
parameters.
While at it remove unnecessary zeroing on get.
No functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 16 Mar 2020 20:47:05 +0000 (13:47 -0700)]
net: socionext: reject unsupported coalescing params
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 16 Mar 2020 20:47:04 +0000 (13:47 -0700)]
net: sfc: reject unsupported coalescing params
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
The check for use_adaptive_tx_coalesce will now be done by
the core.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Thu, 12 Mar 2020 15:20:32 +0000 (17:20 +0200)]
net/mlx5: Avoid forwarding to other eswitch uplink
Do not allow forwarding of encapsulated traffic received from one eswtich's
uplink to another eswtich's uplink.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Cohen [Mon, 24 Feb 2020 14:59:54 +0000 (16:59 +0200)]
net/mlx5: Eswitch, enable forwarding back to uplink port
Add dependencny on cap termination_table_raw_traffic to allow non
encapsulated packets received from uplink to be forwarded back to the
received uplink port.
Refactor the conditions into a separate function.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Cohen [Thu, 13 Feb 2020 12:05:14 +0000 (14:05 +0200)]
net/mlx5e: Add support for offloading traffic from uplink to uplink
Termination tables change the direction of a packet in hw from RX to SX
pipeline. Use that to offload hairpin flows received from uplink and
sent back to uplink.
Currently termination tables are used for pushing VLAN to packets
received from uplink and targeting a VF. Extend the implementation to
allow forwarding packets to uplink. These packets can either be
encapsulated or not.
In case encapsulation is needed before forwarding, move the reformat
object to the termination table as required.
Extend the hash table key to include tunnel information for the sake of
reusing reformat objects.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Cohen [Thu, 27 Feb 2020 10:22:46 +0000 (12:22 +0200)]
net/mlx5: Don't use termination tables in slow path
Don't use termination tables for packets that are steered to the slow path,
as a pre-step for supporting packet encap (packet reformat) action on
termination tables. Packet encap (reformat action) actions steer the packet
to the slow path until outer arp entries are resolved.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Cohen [Sun, 1 Mar 2020 13:31:49 +0000 (15:31 +0200)]
net/mlx5: Avoid configuring eswitch QoS if not supported
Check if QoS is enabled for the eswitch before attempting to configure
QoS parameters and emit a netlink error if not supported.
Introduce an API to check if QoS is supported for the eswitch.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Vladyslav Tarasiuk [Wed, 4 Mar 2020 11:33:50 +0000 (13:33 +0200)]
net/mlx5e: Fix devlink port register sequence
If udevd is configured to rename interfaces according to persistent
naming rules and if a network interface has phys_port_name in sysfs,
its contents will be appended to the interface name.
However, register_netdev creates device in sysfs and if
devlink_port_register is called after that, there is a timeframe in
which udevd may read an empty phys_port_name value. The consequence is
that the interface will lose this suffix and its name will not be
really persistent.
The solution is to register the port before registering a netdev.
Fixes:
c6acd629eec7 ("net/mlx5e: Add support for devlink-port in non-representors mode")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Roi Dayan [Tue, 3 Mar 2020 09:18:53 +0000 (11:18 +0200)]
net/mlx5e: Fix rejecting all egress rules not on vlan
The original condition rejected all egress rules that
are not on tunnel device.
Also, the whole point of this egress reject was to disallow bad
rules because of egdev which doesn't exists today, so remove
this check entirely.
Fixes:
0a7fcb78cc21 ("net/mlx5e: Support inner header rewrite with goto action")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Paul Blakey [Tue, 10 Mar 2020 09:24:22 +0000 (11:24 +0200)]
net/mlx5e: en_tc: Rely just on register loopback for tunnel restoration
Register loopback which is needed for tunnel restoration, is now always
enabled if supported and not just with metadata enabled, check for
that instead.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Saeed Mahameed [Mon, 16 Mar 2020 22:47:03 +0000 (15:47 -0700)]
net/mlx5e: CT: Fix stack usage compiler warning
Fix the following warnings: [-Werror=frame-larger-than=]
In function ‘mlx5_tc_ct_entry_add_rule’:
drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:541:1:
error: the frame size of 1136 bytes is larger than 1024 bytes
In function ‘__mlx5_tc_ct_flow_offload’:
drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:1049:1:
error: the frame size of 1168 bytes is larger than 1024 bytes
Fixes:
4c3844d9e97e ("net/mlx5e: CT: Introduce connection tracking")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Paul Blakey [Sun, 15 Mar 2020 13:18:47 +0000 (15:18 +0200)]
net/mlx5e: CT: Fix insert rules when TC_CT config isn't enabled
If CONFIG_MLX5_TC_CT isn't enabled, all offloading of eswitch tc rules
fails on parsing ct match, even if there is no ct match.
Return success if there is no ct match, regardless of config.
Fixes:
4c3844d9e97e ("net/mlx5e: CT: Introduce connection tracking")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
YueHaibing [Sat, 14 Mar 2020 10:44:46 +0000 (18:44 +0800)]
net/mlx5e: CT: remove set but not used variable 'unnew'
drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:
In function mlx5_tc_ct_parse_match:
drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:699:36: warning:
variable unnew set but not used [-Wunused-but-set-variable]
Fixes:
4c3844d9e97e ("net/mlx5e: CT: Introduce connection tracking")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Paul Blakey [Mon, 16 Mar 2020 12:55:11 +0000 (14:55 +0200)]
net/mlx5: E-Switch, Skip restore modify header between prios of same chain
Restore modify header writes the chain mapping on the packet.
This modify header and action is added on all prios connections,
and gets overwritten with the same value consecutively in prios
of the same chain.
Use the chain's modify header only for the last prio of a given tc
chain.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Paul Blakey [Sun, 1 Mar 2020 14:12:00 +0000 (16:12 +0200)]
net/mlx5: E-Switch: Fix using fwd and modify when firmware doesn't support it
Currently, if firmware doesn't support fwd and modify, driver fails
initializing eswitch chains while entering switchdev mode.
Instead, on such cases, disable the chains and prio feature (as we can't
restore the chain on miss) and the usage of fwd and modify.
Fixes:
8f1e0b97cc70 ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>